Fundamentals of Valves
Fundamentals of Valves
Fundamentals of Valves
Fundamentals of Valves
http://www.mohandes-iran.com
What is valve?
Classification of valves
Valve types.
Methods of controlling flow through a valve.
Basic Parts of the valve.
Valve types
http://www.mohandes-iran.com
What is valve?
A valve is a device that regulates, directs or controls the flow of a fluid by
opening, closing, or partially obstructing various passageways.
Valve Functions
Stopping and starting fluid flow.
Varying (throttling) the amount of fluid flow.
Controlling the direction of fluid flow.
Regulating downstream system or process pressure.
Relieving component or piping over pressure.
http://www.mohandes-iran.com
Classification of Valves
The following are some of the commonly used valve classifications, based on
mechanical motion:
•Linear Motion Valves. The valves in which the closure member, as in gate, globe,
diaphragm, pinch moves in a straight line to allow, stop, or throttle the flow.
•Rotary Motion Valves. When the valve-closure member travels along an angular or
circular path, as in butterfly, ball, plug valves.
•Quarter Turn Valves. Some rotary motion valves require approximately a quarter turn,
0 through 90°, motion of the stem to go to fully open from a fully closed position or
vice versa.
http://www.mohandes-iran.com
Methods of controlling flow through a valve.
http://www.mohandes-iran.com
Methods of controlling flow through a valve.
http://www.mohandes-iran.com
Methods of controlling flow through a valve.
http://www.mohandes-iran.com
Methods of controlling flow through a valve.
http://www.mohandes-iran.com
Basic Parts of the valve
Body
Bonnet
Trim (internal elements)
Actuator (Handwheel)
Packing
http://www.mohandes-iran.com
Basic Parts of the valve
Body
It is called the shell, is the primary pressure boundary of a valve. It serves as the
principal element of a valve assembly because it is the framework that holds
everything together.
http://www.mohandes-iran.com
Basic Parts of the valve
Bonnet
The cover for the opening in the valve body.
Bonnets Features
• bonnet is the second principal pressure boundary of a
valve.
• It is cast or forged of the same material as the body and
is connected to the body by a threaded, bolted, or
welded joint.
• the attachment of the bonnet to the body is considered
a pressure boundary. This means that the weld joint or
bolts that connect the bonnet to the body are pressure-
retaining parts.
• Valve bonnets, although a necessity for most valves,
Welded Bonnet
represent a cause for concern,
• Bonnets can complicate the manufacture.
• Increase valve size.
• Represent a significant cost portion of valve cost.
• Bonnets are a source for potential leakage.
Valve Trim
http://www.mohandes-iran.com
Basic Parts of the valve
Internal parts of the valve
Disk
Disk is the third primary principal pressure boundary. It
provides the capability for allowing and stopping fluid flow.
The disk is a pressure-retaining part. Disks are typically
forged and, in some designs, hard-surfaced to provide good
wear characteristics. Most valves are named, in part,
according to the design of their disks.
http://www.mohandes-iran.com
Basic Parts of the valve
Internal parts of the valve
Stem
Connects the actuator (hand wheel) and disk, is
responsible for positioning the disk.
http://www.mohandes-iran.com
Basic Parts of the valve
Actuator (hand wheel)
Operates the stem and disk
assembly. An actuator may be
operated manually or
automatically.
Actuator
Packing
It is used to prevent leakage from
the space between the stem and
the bonnet.
Packing
http://www.mohandes-iran.com
Valve Selection Considerations
http://www.mohandes-iran.com
There are factors govern the basic materials selection
Corrosion-resistance requirements.
Thermal shock.
Piping stress.
Fire hazard.
Body Materials
For small valves are usually brass, bronze, or forged steel
For larger valves, cast iron, cast ductile iron or cast steel as required for the
pressure and service.
http://www.mohandes-iran.com
Seat and Valve Disk Materials
The valve seat and valve disk are sometimes referred to as the valve trim
and are usually constructed of the same material selected to meet the
service requirements.
http://www.mohandes-iran.com
http://www.mohandes-iran.com
Table 2.10 Common ASTM Materials for Bodies and Bonnets
http://www.mohandes-iran.com
Threaded ends
◦ Used for small application up to 4 in. they are cheap but can be stripped
and leak, for this reason they are used when leakage is not a problem.
Threaded ends should not be used with corrosive processes, since the
threads can either fail or become inseparable.
Threaded end
http://www.mohandes-iran.com
Welded ends
◦ When zero leakage is required for
environmental, safety, or any efficiency
reasons the piping can be welded to the
valve, providing one piece construction.
Many users insist that high-pressure Welded end
application requires a permanent end
especially if they involve high temperatures
Flanged ends
◦ The most expensive but are the best from
an installation and removal standpoint.
The main advantage of flanges is that the
valve can be removed easily from the line
Flanged end
http://www.mohandes-iran.com
Valve types
http://www.mohandes-iran.com
Globe Valves
A globe valve is a linear motion valve used to stop,
start, and regulate fluid flow. The three primary
body designs for globe valves are Z-body, Y-body,
and Angle.
Advantages
o Recommended for throttling applications.
o Good for frequent operation.
o Easy to repair.
Disadvantages
o Flow path causes a significant pressure drop.
o Globe valves are more costly than alternative
valves.
Globe_Valve_-_FBV.mp4
http://www.mohandes-iran.com
Gate Valves
Flow is controlled by raising or lowering the valving
element. Gate valves are not usually used to
regulate flow because the valving element can be
damaged when in the partially open position.
Similarly, they also limit the pressure drop across
the valve when fully open.
http://www.mohandes-iran.com
Advantages
• Gate valves opens or closes slowly, which prevents fluid hammer and
subsequent damage to the piping system.
• They need long operation time since setting the valve to the fully open or
closed position requires the handle to be turned many times.
• Good choice for on-off service.
• Full flow, low pressure drop.
• Bidirectional.
Disadvantages
• It is not suitable for throttling applications.
• It is prone to vibration in the partially open state.
• It is more subject to seat and disk wear.
• Repairs, such as lapping and grinding, are generally more difficult to
accomplish.
http://www.mohandes-iran.com
Ball Valves
A ball valve is a rotational motion valve that uses a
ball-shaped disk to stop or start fluid flow.
Advantages
- Maintains and regulates high volume, high
pressure, and high temp flow
- Low purchase and maintenance costs.
- No lubrication requirements.
- Give tight sealing with low torque.
- Time of valve operation is minimized.
- Can be used for throttling service.
- Can handle fluids with suspended solids.
Disadvantages
- Have relatively poor throttling characteristics.
- Difficult to clean, leads to contamination
Advantages
◦ They are suitable for large valve applications.
Disadvantages
◦ Difficult to clean
Butterfly_Valves.mp4
http://www.mohandes-iran.com
Diaphragm Valves
A diaphragm valve is a linear motion valve that is used to start,
regulate, and stop fluid flow. The name is derived from its
flexible disk, which mates with a seat located in the open area at
Advantages
- valve components can be isolated from the process fluid.
Disadvantages
- The diaphragm becomes worn more easily and regular
maintenance is necessary.
- These types of valves are generally not suited for very high
http://www.mohandes-iran.com
Pinch Valve
A pinch valve is the simplest valve design. It is a linear motion valve that
is used to start, regulate, and stop fluid flow. It uses a rubber tube (pinch
tube) to control the fluid.
Advantages
- They are ideally suited for the handling of slurries, liquids with large
amounts of suspended solids, and
systems that convey solids pneumatically.
- Can be used for application where corrosion or metal
contamination of the fluid might be a problem.
- The flow passage is straight without any crevice.
- There are no internal moving parts in contact with the fluid.
- Low maintenance due to wear or pressure.
- Minimum items to change. Tube ONLY.
Disadvantages
- Cannot be used in high temperature/ pressure applications
- Cannot be used with gas media
http://www.mohandes-iran.com
http://www.mohandes-iran.com
Check Valves
Check valves are designed to prevent the reversal of flow in a piping system. These
valves are activated by the flowing material in the pipeline. The pressure of the fluid
passing through the system opens the valve, while any reversal of flow will close the
valve. Closure is accomplished by the weight of the check mechanism, by back
pressure, by a spring, or by a combination of these means. The general types of check
valves are swing, tilting-disk, piston, , and stop.
http://www.mohandes-iran.com
tilting-disk Check Valve
http://www.mohandes-iran.com
Stop Check Valve
Lift Check Valve
http://www.mohandes-iran.com
J.AYAZI
20-MAR-2014
http://www.mohandes-iran.com