AHMEDABAD MUNICIPAL CORPORATION

(EAST ZONE)

TENDER DOCUMENT
CONSTRUCTION OF SUB ZONAL OFFICE BUILDING AT
F.P. NO. 207, T.P.S. NO. 113 (VASTRAL) IN VASTRAL WARD,
EAST ZONE, AHMEDABAD

Volume -II
Financial BID

Dy. Municipal Commissioner (East Zone)

Ahmedabad Municipal Corporation.
Harubhai Mehta Bhavan,Viratnagar,
Ahmedabad

1
 AHMEDABAD MUNICIPAL CORPORATION

Rate Amount
I. No. Qty Items Per
Rs. Ps. Rs. Ps.
Excavation for foundation including sorting out stacking of useful
1 material & disposing of excavated stuff upto 50 mt. lead.Loose or
soft soil.
a 2095 up to 1.5 mt. depth 122 Cu.M. 255590
b 1990 1.5 to 3.0 mt. depth. 135 Cu.M. 268650
c 3805 3.0 to 5.0 mt. depth 148 Cu.M. 563140
d 715 5.0 to 6.0 mt. depth 161.3 Cu.M. 115329.5
d Boring, Providing and installing cast in situ single under reamed
piles of specified diameter and length below pile cap in M-25
cement concrete, to carry a safe working load not less than
specified, excluding the cost of steel reinforcement but including
the cost of boring with bentonite solution and the length of the pile
to be embedded in pile cap etc. all complete. (Length of pile for
payment shall be measured upto to the bottom of pile cap)
i 7.00 450 mm dia. Piles 2835.95 Rmt. 19851.65
e Extra over item No. 20.3 for providing additional bulb in under
reamed piles, under specified dia meter (Only the quantity of extra
bulbs are to be paid).
i 2.00 450 mm dia. Piles 1795.20 Each 3590.4
2 2 Provdg. & laying cement concrete 1:5:10 (1 cement : 5 fine sand :
10 graded brick aggregates 40 mm nominal size) and curing
complete, excluding cost of form work in foundation & Plinth.
2048.00 Cu.M. 4096
3 Provdg. & laying cement concrete 1:3:6 (1 cement : 3 coarse sand
: 6 hand broken stone aggregates 40 mm nominal size) and
curing complete excluding cost of form work in
a 1 (A) Foundation and plinth 2501.00 Cu.M. 2501
4 385 Provdg. & laying cement concrete 1:4:8 (1 cement : 4 coarse sand
: 8 hand broken stone aggregates 40 mm nominal size) and
curing complete excluding cost of form work in foundation& plinth.
2249.00 Cu.M. 865865
5 3000 Filling available excavated earth (excluding rock) in trenches,
plinth, sides of foundations etc. in layers not exceeding 20 cm. in
depth consolidation each deposited layer by ramming and
watering. 79.00 Cu.M. 237000
6 40 Filling in plinth with sand under floors including watering,
ramming, consolidating, compacting and dressing etc. completed. 398.00 Cu.M. 15920
7 75.00 Filling in foundation and plinth with murrum , Garden soil or
selected soil in layers of 20 cm. thickness including watering,
ramming and consolidating etc. Complete. 286.00 Cmt 21450
8 Brick work using common burnt clay building bricks having
crushing strength not less than 35 kg/Sq. cm. in cement mortar
1:6 (1 cement : 6 fine sand)
a 25 (a) in foundation & Plinth 2798.00 Cu.M. 69950
b 360 (b)Super structure 2963 Cu.M. 1066680
c 177 Above First Floor Lvl. 2993.4 Cu.M. 529831.8
9 320.00 I.Half brick masonry in common burnt clay building bricks having
crushing strength note less than 35 Kg/Sq. Cm. in cement mortar
1:4 (1 cement : 4 coarse sand) in Super structure upto floor four
level
418 Sq.M. 133760

2
10 Providing and laying controlled cement concrete / Ready Mix
Concrete of M-20 Grade and curing complete, including the cost
of form work, Scaffolding But Excluding the cost of reinforcement
for reinforced concrete work For any Height up to Floor Four
Level.
a 621 Foundations,Raft,Footings,Mass concrete in M20 Grade 4321.00 Cu.M. 2683341
b 430 RCC Retaining wall / Column / Stair in M-20 Grade for any
thickness 6107.00 Cu.M. 2626010
c 607 Tie Beam , Lintel , Beam- Bracket , Coping ,Slab, balcony,
weather shed, loft , any cantilever etc in M-20 Grade 4900.00 Cu.M. 2974300
d 800 extra for M-250 Grade 183.00 Cu.M. 146400
e Rebaring :
Drilling hole of required diameter and depth as directed for fixing
of rebars,using hammer drill, cleaning the hole using mechanical
air flower, water etc,providing and fixing rebar in the drilled hole
using Fischer - FIS 360 or Equivalent approved make
Cementetious chemical grout and sealant with necessary
scaffolding, staging, labour, tools and equipment etc. complete as
directed by Engineer-in-charge.
i 50 (a) 8 mm dia bar (100 mm depth ) 69.00 No. 3450
ii 100 (b) 10 mm dia bar ( 100 mm depth ) 105.00 No. 10500
iii 100 (c) 12 mm dia bar (125 mm depth ) 145.00 No. 14500
iv 30 (d) 16 mm dia bar (175 mm depth ) 260.00 No. 7800
v 20 (e) 20mm dia bar (200 mm depth ) 405.00 No. 8100
vi 10 (f) 25 mm dia bar (250 mm depth ) 635.00 No. 6350
11 Providing and laying controlled cement concrete 1:2:4( 1cement :
2 coarse sand : 4 Graded stone aggregate 20 mm nominal size )
and curing complete, excluding the cost of form work and
reinforcement for reinforced concrete work in:
a 5 Foundations, footings, base of columns, and mass concrete. 3184.00 Cu.M. 15920
b 1 Slabs/grade slab, landing shelves, Balconies, lintels, beams,
girders, and cantilever, up to floor four level. 3384.00 Cu.M. 3384
1210 Providing & Applying Tremix method ( Vaccum de extracted &
Powered trowelled ) for Concrete Flooring with necessary finishing
c either smooth or wire finish as approved by consultants. Rate
shall includes the rate of side shuttering with channel , rails to
form panels etc. complete.
75.00 Sq.M. 90750
400 Providing & filling Polysulphide Sealant of "Fairmate" , "
d Pidilite" or equivalent make including Groove cutting of size :
12.5mmx25 mm for Expansion joints.
195.00 Rmt 78000
12 Providing form work in ordinary timber planking so as to give a
rough finish including centering, shuttering, strutting and propping
etc. height of propping and centering below supporting floor to
celling not exceeding 4 M & removal of the same for in situ
reinforced or plain concrete work upto floor four level
a 10
Providing Formwork in ordinary timber planking so as to give a
rough finish incl.centering,shuttering strutting and propping etc
height of propping and centering below supporting floor to ceiling
for any height and removal the same for in situ reinforced
concrete and plain concrete work for all type of RCC work
109.00 Smt 1090
13 195000.0 Providign Thermo Mechanically treated bars (TMT BARS)
confirming to IS 786/FC 415 for R.C.C works includings bendings,
binding and placing in position complete upto floor four level.
44.4 Kg. 8658000

3
14a 100 Providing and laying polished / River Washed Kota stone slab
(Polished, Green colour) flooring over 20 mm. (average) thick
base of cement mortar 1:6 (1 cement : 6 coarse sand) or lime
mortar 1:1.5 laid over and joined with grey cement slurry including
rubbing and polishing complete.25 mm th.
769.00 Sq.M. 76900
b 25 Providing and laying Combination of 25 mm thick River washed
Kota Stone & Black Kaddapa stone in Floor over 25 mm.
(average) thick base of cement mortar 1:6 (1 cement : 6 coarse
sand)and joined with matching shade, pigmented cement slurry
including rubbing and polishing complete & making of grooves as
per drgs. 1150.00 Sq.M. 28750
c 10
Providing and laying 100 x 100 mm x 75 mm thick grey or
coloured coble stone block over a bed of sand(minimum 75 mm
thickness).inclu.spreading sand on existing driven way
compacting sand bed by ramming and interlocking them with the
use of a suitable plate vibrator and incl.all incidental work like
cleaning the site of debries etc.The paver blocks supplied by the
party must confirm to following notes and complete as directed by
EIC.Rate for all level,heights,lift,leads.(No Extra payment shall be
made for any Architectural detail)
1680.00 Sq.M. 16800
15a 15 Providing and laying polished Kota stone slab 25 mm. thick in
Platform , dado and pillars laid on 10 mm. thick cement mortar 1:3
(1 cement : 3 coarse sand) jointed with grey cement slurry
including rubbing and polishing etc. compl

888.00 Sq.M. 13320

b 105 Providing & Laying 20 mm thickPolished Kota Stone upto 17 cm
High in Riser of Stair , Skirting etc. as per Design given laid on 10
mm. thick cement mortar 1:3 (1 cement : 3 coarse sand) jointed
with grey cement slurry including rubbing , polishing , moulding
etc. compl as per Direction of engg. in charge
170.00 Rmt 17850
c 440 Making of 2 mm Grooves in Kota / Granite stone Tread in stair
case portion for non skiding purpose as per dir. Of engg. In
charge. 9.50 Rmt 4180
16 5 Providing and laying white/Colur glazed tiles 6 mm thick in flooring
treads of steps and landing laid on a bed of 12 mm thick cement
mortar 1:3 (1 cement : 3 coarse sand) finished with flush pointing
in white cement.
692.00 Sq. M. 3460
17 481 Providing and layingWhite / Colour glazed tiles 6 mm. thick in
skirting, risers of steps and dedo on 10 mm. thick cement plaster
1:3 (1 cement : 3 coarse sand) and jointed with white cement
slurry.
906.00 Sq. M. 435786
18a 25 Providing & Laying Natural Stone Type Decorative Tiles of
standard make as approved by consultants. walls / columns
cladding laid on 12 mm th. Cement mortar 1:3 ( 1 cement : 3
coarse sand ) jointed with grey cement slurry with necessary
scaffolding etc. complete.
1180.00 Sq.mt. 29500
b 50 Providing & Fixing Exterior type 8 mm thick 150 mm wide , 3.0
mtr. in Length Shera / Zykron or Equivalent make Fibre Cement
Plank of Approved Shade by Providing & Fixing Necessary Steel
Frame work etc. at Any Height by Providing Necessary
Scaffolding etc. Complete as per Dir. Of Consultants / Engg. In
Charge.
1450.00 Sq.mt 72500

4
19 a 180 Providing and laying marble stone slab in Window Jambs, Dado,
flooring over 20 mm. (Average) base of cement mortar 1:6 (1
cement: 6 coarse sand) or L.M. 1:1.5 laid and jointed with grey
cement slurry including rubbing and polishing complete: (A)
Marble slab 20 mm. thick.
1669 Sq. M. 300420
b 1270.0 Providing and laying 1st quality Full body Glazed vitrified tiles for
Floor / Dado / Skirting of any Size as per Consultants Design i.e.
300mx600 mm ,600 mm x 600 , 800mmx800 mm etc. (size and
thickness to be specified by the manufacturer),of any desired
shade & color specified by Architect, laid with cement paste on
and including cement mortar 1:4 bedding laid to proper slope or
as required on site, line and level, as specified. All joints filled with
epoxy grout (avg. 4*10 to12 mm) and protection with minimum
10mm thick POP Laying over PVC bubble Sheet/Floor protector
approved by EIC and later removing and maintaining it till handing
over, including cutting of tiles,curing and cleaning complete all as
per detailed drawings and specifications as directed by EIC for all
lift,all floor levels and leads. The item to include all materiral,
fixing, scaffolding, labour, Wastage etc. complete in all respects
etc. complete as direction by E.I.C.
Note: No extra payment pay for architectural Ornamental Design
upto 10% of flooring area. Rate shall be inclusive of cutting of tiles
in any shape, at any level for service cutout.

1748.00 Sq. M. 2219960

20 90.0 Providing and laying Ceramics tiles in flooring, treads of steps
and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3
coarse sand) and jointed with white cement slurry.

663.00 Sq. M. 59670

21 a 120 Providing & Laying 18 mm thick Mirror polish granite For flooring ,
counter , stair -riser , tread , skirting , dedo etc. machine cut or
chiselled on bed of cement mortar 1:1 pointing with neat cement
slurry incl. moulding etc. comp. as per instruction of engineer in
charge.

2672 Sq. M. 320640

b 5 Providing & Fixing 20 mm thick Mirror Polished Decorative Granite
Board with Computerised Golden Letters Discription as per
instructions of engg. in charge to M.S. frame structure for
Inaugaration & Public Handover Function
4304 Sq.mt. 21520
22 a 8561 Provdg. 15 mm. thick cement plaster in single coat on fair side of
brick concrete walls for interior plastering upto floor four level and
finished even and smooth in C.M.1:4.
121 Sq.M. 1035881
b 400 Providing & fixing 15 cm wide chicken mesh jali with nails & then
application of 15 mm plaster on R.C.C. & masonary joints as per
dir. of engg. In charge. 48 Sq.mt 19200
c 70 Providing & Mixing of Water proof Chemical in Cement mortat for
Inside/ outside Plaster work of "Roof " , "Fosroc" or equivalent
make in proportion as per company's user manuals & Direction of
engg. In charge.
165 Litre 11550

5
23a 2025.00 Providing 20 mm th. Double coat Sand face / Mala Cement
Plaster on Walls upto height 10.0 mtrs. Above Ground level
consisting of 12 mm th. Backing coat of C.M. 1:3 ( 1 cement : 3
Ssand ) & 8 mm th. Finishing coat of C.M. 1:1 ( 1 cement : 1 sand
) ets. Complete.
189 Sq.M. 382725
b 50.00
P./L. METALIC HERITAGE SURFACE TEXTURE
Providing and fixing of HERITAGE textured homogeneous wall
finishing system from BAKELITE HYLAM LTD or equivalent make
consisting of a two component system of (25 kgs per Pack) made
of 92% silica particles coated with fade resistant pigments, 100%
acrylic polymer bonding agent (5kgs per pack) with the applied
thickness of the coating being between 0.8mm-1.2mm to be
applied on a cured, smooth level plaster without keying, as per the
shades/combinations approved, as per the manufacturer
directions, for usages, tobe applied by an approved applicator of
the manufacturer, as per the directions / supervision of the
engineers in charge, all complete.
591.7 Sq.m 29585
c 600.00 Providing & applying two coats of Textured Plaster fine filaments
made of polymer and including one coat of primer & two coats of
external acrylic emulsion paint of approved make & colour shade
to external wall with making grooves. Applying sand papering the
surfaces to remove dust, dirt etc; filling the cracks with approved
filler material to achieve level surface for all floor and all height as
approved by Architect/ Engineer in Charge.

458 Sq.m. 274800

24a 2000 White / Color washing with lime on undecorated wall surfaces (two
coats) to give an even shade including thoroughly brooming the
surface to remove all dirt, dust mortar drops and other foreign
matter.
7.8 Sq.M. 15600
24 b 1400 Providing & applying 3 coats of weather proof exterior emulsion
paint, waterproof and weather proof, External paint Apex or
approved equivalent of desired shade, after thoroughly brushing
the surface to remove all dirt and remaining all loose powdered ,
free from mortar dropping and other foreign matter and sand
paper smooth etc. complete as per E.I.C.

174 Sq.M. 243600

25a 6500 Wall Painting (two coats) with plastic emulsion paint of approved
brand and manufacture and of shade required on undecorated
wall surfaces to give an even shade, over and including a priming
coat with alkali resistance primer of approved brand and
manufacture after thoroughly brushing the surface free from
mortar droppings, and other foreign matter and also including
preparing the surface even and sand -papered smooth

49.8 Sq.M. 323700

b 6500 Extra over above item for every subsequent coat of of wall
painting with plastic emulsion paint of approved brand.
21.2 Sq.mt. 137800
c 6500 Providing & Applying Three Coats of Birla Putty or Equivalent
Putty on Primed Surface of Inside wall to make the surface even &
smooth upto the Satisfaction of Engg. In Charge including
Necessary Sandpapering etc. complete.
45 Sq.M. 292500

6
26 Providing & Laying & Jointing glazed stoneware pipes incl.
excavation up to 2.0 mt.,refilling, trasporting the pipe to work site,
unloading, lowering in trenches, laying and jointing the pipes in
c.m. 1:1 incl. all jointing materials such as cement, sand, hemp,
bitumen as dire. testing the pipe line to a head of 1.5 mt. and
hydraulic test as dire incl. watering trenches, spreading , and
carting away of surplus earth within 100 mt.lead as dire. etc.

a 70 23 cm dia. 386 Rmt 27020

b 15 15 cm dia 183 Rmt 2745
c 15 10 cm dia. 134 Rmt 2010
27 Constructing Slab type Chamber of following size including
excavation, refilling, BBCC (1:5:10), for foundation, C.C.Channel
(1:2:4) finished, 15 mm thick cement plaster inside & outside in
CM 1:3, finishing with cement slurry, P/F 4 mm dia M.S.Steel
HDPE coated steps 35 cm c/c at 35 cm staggered masonary in
CM 1:5, RCC Slab in CC 1:1.5:3, including Centering &
reinforcement , cost of chamber seat cover etc..completed.

a 5 (A) 0.60 X 0.45 mt. size Inside Clear, Depth from 0.0 to 0.90meter
for pipe dia <=150mm. 2533.00 No. 12665
28 Constructing Slab type M.H. Chamber of the following size
including excavation, refilling, brick bats cement concrete (1:5:10),
CC Channel (1:2:4) finished, 15 mm thick cement plaster inside &
outside in CM 1:3, finishing with cement slurry, P/F 4 mm dia
M.S.Steel HDPE coated steps 35 cm c/c at 35 cm staggered
masonary in CM 1:5, RCC Slab in CC 1:1.5:3, including Centering
& reinforcement, cost of Manhole seat cover etc..completed.
of Size 1.00 X 1.40 meter (Inside Clear)
a 5.00 (A) 0.00 to 2.00 meter depth, 11399.00 No. 56995
29a 12.00 Providing & fixing White/Light Coloured Vitreous China Large
Urinal 590mm x 375mm x 390mm as per product detail with
Flushing System as per product detail, with C.I. hangers, Bottle
Trap, Prassmatics angular cock, Waste Coupling, including cutting
and making good the walls and floors wherever required.
3879 No. 46548
b 25.00 Providing & Fixing Bib/Angle/Stop cock of " Ess Ess" - Trend
series or equivalent standard make as approved by engg. in
charge all complete. 675 No. 16875
30 15.00 Provdg. & laying S.W. Gully trap with C.I. garting brick masonry
chamber & water tight C.I. cover with frame of 300 mm x 300
mm size ( inside) with standard weight.sqare mouth trap size 150
x100 mm P trap 1227 No. 18405
31a 3000 Providing & Fixing Sintex, National or Equivalent make Polytheline
over head tank with necessary dia holes for outlet , inlet over flow
and washout with necessary washer and checkput etc. comp. 5.5 Litre 16500
b 75000 RCC Underground water tank for Domestic & Fire purpose as
specified by consultant or AMC Fire department including
Excavation, P.C.C., bottom slab,top slab, periphery walls, form
work, water proof plaster on wall (Inside & Outside) and
waterproofing ,etc.complete as per Structural design and
details,piping,valves,fittings and fixtures as directed
(Reinforcement steel shall not be given seperately.) 15 Litre 1125000
32 40 Extra for excavation of asphalt of any thickness the asphalt carpet
with soling metals etc. with stacking the same etc. comp. as dire. 40 Sq.M. 1600
33 18 P/F PVC / C.I. (span) nahni trap and all of the following nominal
dia of self cleanising design with C.I.Screw down or hinged
greeting inclusive cost of cutting and making good the walls and
floors 100 mm inlet and 50 mm outlet etc. comp. 351 No. 6318

7
34 Providing & fixing rigid C.P.V.C. pipes of Ashirvad FlowGuard or
astral orapproved equivalent make (SDR 11) with necessary
SWR fittings, coupler, bends, tees etc and fixed to walls/ columns
with PVC clamps with standard fittings joints to be filled with
approved solution etc. complete.
a 100 15 mm 99.00 Rmt 9900
b 200 25 mm 175.00 Rmt 35000
c 100 40 mm 333 Rmt 33300
d 40 50 mm 524 Rmt 20960
35 Provdg. And fixing to wall ,ceiling and floor 6.00 kg. F/Sq.Cm
working pressure polythelene pipes of the following outside
diameter, low, density, complete with special flange compression
type fittings, wall clips etc. making good wall ceiling and floor.
a 35 (A) 75mm dia 178.00 Rmt 6230
b 150 © 110 mm dia 318.00 Rmt 47700
36 9 Provdg. & fixing White / Color Vitreous china Orissa pan with
integral trap of "Cera" - Prima series or "Hindware" make of size
500x400 mm incl. jointing the trap with PVC / soil pipewith cement
mortar1:1 (1 cement : 1 fine sand) as per direction of engg. In
charge.
871 No. 7839
37a 9 Providing & fixing Wall-mounted European Closet Suite P-Trap
(White/Light Coloured) of Cera , Hindwear or Equivalent make as
Selected by engg. in charge / consultant all included with lid
(heavy duty) , C.I. Chair Brackets, C.P. brass hinges, All Internal
fittings complete with rubber buffers, C.P. nuts, bolts, ChaKi, etc
making holes in walls & floors, & finishing for ready to use
including cutting and making good the wall where required. 5688 No. 51192
b Provdg. & fixing chromium plated brass flush cock of " Ess Ess"-
Trend series or equivalent make incl.fixing in pipe etc. comp.as
per dir. Of engg. In chaarge.
18 (1) 25 mm dia. 1800 No. 32400
c 9 Health faucet - Providing & fixing of Hand Jet Shower
(Health Faucet) with 1mtr Flexible PVC Tube, wall hook, and 2-
Way Bib Cock. 1255 No. 11295
38a 6 Provdg. & fixing White / Color Vitreous china Counter wash basin
with signle hole for pillar tap of "Cera " - Concord series of 550
x425 mm size to be fiited in stone counter with necessary
brackets painted white incl. cutting holes and making good the
same .Cost Includes P/F C.P. brass waste coupline, 32 mm dia
fisher union , 15 mm dia. Pillar cock & Angle cock of " Ess Ess"-
Trend series , 32 mm dia. Waste pipe etc. complete as per dir. of
engg. in charge. 2950.00 No. 17700
b 1 Providing & Fixing S.S.304 Grade Sink of Nirali / Krishna or
Equivalent Make for Kitchen Platform of size : 24":x18" as per
Direction of engg. In charge. 4650.00 No. 4650
c 3 Provdg. & fixing wash basin with signle hole for pillar tap with C.I.
or M.S. brackets painted white incl. cutting holes and making good
the same . Incl. P/F C.P. brass waste pipe 32 mm dia M.I.Fisher
union of 32 mm dia. Pilar trap, capstren head, srew down high
pressure with screw of 15 m dia etc. comp.(550 x 400 mm size ) 1637.90 No. 4913.7
39 5 Provdg. & fixing 600mm x 450 mm Bevelled edge mirror of
superior glass mounted of .6 mm th. A.C. sheet or plywood sheet
and fixed to wooden pluge with C.P. brass screws and
washers.Bldg.s.o.r.2015-2016,it. No.23.143 Ch-23 ) 580 No. 2900
40 2 Provdg. & fixing C.P..Brass towal rail complete with C.P. brass
brackets fixed to wooden plugs with C.P. Brass screws.(600 mmx
20 mm size) 533 No. 1066
41 Provdg. & fixing C.P. Brass screw down bib taps of following size
a 20 (I) 15mm dia 248 No. 4960

8
42 Providing and fixing heavy gunmetal sluice valve of
approved make(Zoloto or equivalent make ) and quality
approved by Architect.
a 9 (A) 15 mm dia 310.00 No. 2790
c 15 (C) 25 mm dia 410.00 No. 6150
d 5 (D) 40 mm dia. 1200 No. 6000
e 2 (E) 50 mm dia. 1450 No. 2900
43 1 Provdg. & fixing C.P.brass pillar tap capstan head, screw down
high pressure with screws shanks and back nuts. (A) 15 mm dia
354.00 No. 354
44a 650 Providing and laying integral cement based water proofing
treatment Av=120 mm thick including preparation of surface as
required for treatment of roof, balconies, terraces etc. and making
necessary vata at the junction of Wall and floor wherever required
as directed by Engineer In Charge and consisting of following
operation .and shall be guaranteed for minimum period of 10
years after handing over the completed building by the main
contractor to be finished as directed. Stamp paper guarantee 10
years to be furnished before receiving any payment from the
client. 400.00 Sq.M. 260000
Applying and grouting a slurry coat of neat cement using 2.75
kg/Sq.Mt. Of cement admixed with proprietary water proofing
compound conforming to IS .2645 over the RCC slab including
cleaning the surface before treatment.
Laying cement concrete using broken bricks/brickbats25 mm to
100 mm size with 50% of cement mortar 1:5 ( 1 cement , 5 coarse
sand)admixed with proprietary water proofing compound
conforming to IS 2645 over 20 mm thick layer of cement mortar of
mix 1:5
After two days of proper curing applying a second coat of cement
slurry admixed with proprietary water proofing compound
confirming to IS 2645
Finishing the surface with 20 mm thick jointles cement mortar mix
1:4 ( 1 cement, 4 coarse sand) admixed with proprietary water
proofing compound conforming to IS: 2645 and finally finishing the
surface with trowel with neat cement slurry and making of
The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test.all above
operations to be done in order and as directed and specified by
Engineer -In-charge
b 650 Providing & Laying white / colored China mosaic clay tile flooring
& skirting dedo on wall ,slab surface as per Design / pattern over
20 mm. th. C.m. 1:4 finished with white cement incldg. Using
approved water proofing etc. comp. as per dire.ction of engg. In
charge
479 Sq. M. 311350
c 12 Filling with good Quality thor as and where directed by the
Architect / Engineer-in-charge, in sunk in layers of 15 cm.
thickness, including watering, ramming well etc. complete, as
directed by the Architect / Engineer-in-charge .
850 Cmt 10200
45 40 Providing and laying Cement concrete flooring for I.P.S. 1:2:4 (for
Indian Patent Stones) (1 cement: 2 coarse sand: 4 graded stone
aggregate 20 mm. nominal size) lain in layer finished with a
floating coat of net cement- 40 mm th by addition of waterproof
chemical etc. complete.

189 Sq.M. 7560

9
46a 15000 Providing & Fixing M.S.grill, gate,stair / balcony railing , elevation
element of Decorative pattern with M.S. Channel ,flat ,medium
grade m.s. pipe, square or round bars with round heanded bolts,
nuts, or by screw. Incl. applying one coat zinc primer and two coat
of oil paint etc. comp.
68 Kg. 1020000
b 400 Providing and fixing stainless steel (Grade 304) railing,daso, grill
work etc. made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making curvature
(wherever required) and fitting the same with necessary stainless
steel nuts and bolts omplete, i/c fixing the railing with necessary
accessories & stainless steel dash fasteners , stainless steel bolts
etc., of required size, on the top of the floor or the ide of waist slab
with suitable arrangement as per approval of Engineerin- charge, (
for payment purpose only basis of standard theorical weight of
stainless steel members shall be considered. No extra shall be
paid for fixing accessories such as nuts, bolts, nails, fasteners
etc.). 446 Kg. 178400
47a 35.0 Providing and fixing in position collapsible steel shutters with
vertical channels 20x10x2 mm braced with flat iron diagonals
20x5 mm size with top & bottom rails of T-iron 40x40x6 mm with
38 mm dia. Steel pulleys complete with bolts , nuts , locking
arrangement , stoppers , handles including applying a priming
coat of red lead paint & two coats of enamel paint of selected
shade & approved make 3478.2 Sq. M. 121737
b 10 Providing corrugated 0.80 mm (22 gauge) thick G.I. sheets
roofing fixed with galvanized iron ‘J’ or ‘L’ hook bolts, and nuts 8
mm. dia with bitumen and G.I. limpet washers filled with white
lead complete excluding the cost of purlines, rafters and trusses.
764 Sq.M. 7640
c 5 Providing valleys 900 mm. overall in plain 1.6 mm. thick G.I. sheet
Class – 3 fixed with ‘J’ or ‘L’ hook bolts and nuts galvanized from
‘J’ or ‘L’ hook bolts and bitumen washers complete.
920 Rmt. 4600
d Providing and fixing rolling shutters of approved make made of 80
mm wide M.S.laths interlocked together through their entier length
& joinned together at the enda by & locks mounted on specially
design pipe shaft with bracket plates giudes channel &
arrangement for inside & out side locking with push pull operation
incl. the the hood cover & spring etc. complete.

6.0 (A) Shutters having any width 3720 Sq.M. 22320

48 16 Providing, Fabricating and Erecting in position Partly Panelled
Partly Glazed / Fully Panelled / Fully Glazed anodised (15 to 25
micron of desired colour) door shutter (double action opening) of
standard aluminum section from 18mm (3/4”) series of Jindal,
Hindalco, Domal or approved equivalent make of size as
described below or of higher series if required as per site
condition-top and vertical style 47.62 x 44.45 x 2mm ( w approx =
1.05 kg./m), lock rail and bottom section 114.30 x 44.45 x 2mm (
w approx = 1.83 kg/m), fitted on frame of size 101.60 x 44.45 x
2mm ( w app = 1.60 kg./m) with standard accesories like handle ,
stopper, locking arrangement, C.P. brass hinges, etc, and glazing
of 5 mm thick clear / tinted float glass of Mody or approved
equivalent, fixed with rubber / PVC beading in upper / Lower and
12 MM both side pre laminated sheet fixed with Glazing clips in
Upper / lower panel etc. complete as per instruction.
4574 Sq.M. 73184
b 4 Extra over item of doors above for providing and fixing double
action floor spring of Everite or approved equivalent as directed.
2462 No. 9848

10
49 190 Providing & Fixing in position Alluminium window 2/3/4 track
sliding / fix / Openable type with frame using approved 15 to 25
micron anodised extruded alluminium section as approved by
Engg. In charge.(Jindal alluminium) units equivalent. including
P/F installing 5 mm thick clear/tinted Glass of standard quality
etc.comp.
3200 Sq. M. 608000
50 7 Providing & Fixing in position Alluminium vents with frame using
approved anodised extruded alluminium section as approved by
Engg. In charge.(Jindal alluminium) units equivalent Frame
section of 63.50 x 38.50 mm. (wt. 0.68 Kg/Rmt) incl. Providing &
Installing 5 mm thick Glass of standard quality etc. comp.
2800 Sq. M. 19600
51 Providing and fixing 35 mm th. Shutters for doors windows &
clearstory windows incl. wood frames as specified 12 cm. x
7cm. size incl. anodised alluminium fixtures and fastenings
including primer coat of approved quality and two coats of oil
paint etc. complete.
a 1 (I) Fully glazed 4201.00 Sq. M. 4201
b 2 (II)Fully panelled 5008.00 Sq. M. 10016
c 2 (III) Partly panelled & partly glazed. 4604.00 Sq. M. 9208
d 10

Providing, Making & Fixing Main Decorative Door using Special

Ghana teak wood frame of size 150x75 mm with 35 mm thick
Fully Glazed / Partly Panelled Partly Glazed Shutters having Top
& Vertical Rail of size 125x35 mm , Middle & bottom Rail of size
150x35 mm using Special Ghana teak wood, 5 mm thick Frosted /
stained Glass as per design including all Heavy type Fixtures /
Fittings / Hadware of Brass / S.S. of Standard makeas selected by
Consultants & special quality approved shade of Melamine
polishing as per direction of Engg. in charge 6450.00 Sq.M. 64500
e Providing and fixing 35mm thick flush shutter for doors, windows
& clearstory windows incl. Indian teak wood frames 12 cm x 7 cm
including anodized alluminium fixture and fastenings incl. primer
coat of approved quality and two coats of oil painting etc.
complete.(Fully pannele or partly panneled and partly galzed
door)
i 121 Flush shutter with both side laminate 4800.00 Sq.M. 580800
ii 2.5 Flush shutter with both side paint 4666.00 Sq.M. 11665
f 30 Providing and Fixing FRP FRAME size 125 x 65 mm and 35 mm
thick FRP shutter with wood grain raised pannel design finish
shutter having extra reinforcement on sides and edges and in
polish finish The core of the shutter is to be filled up with injected
fire extingushing grade.polyurethane foam done in situ along with
embedded wooden pieces for stiffering and also for tacking hinges
and fixtures. The whole FRP frame and shutter is to be water
proof.weather proof,tennite proof and resistance to mild acid/
Alkali, Rates are to be inclusive of S.S. hinges with necessary
screws and brass fixtures and fasening. Product should have 3
years performance guarntee and company have ISo 9001-2000
certificate.

3823.00 Sq.M. 114690

52 110 Brick projection patta work usiing common burnt clay building
bricks having crushing strength not less than 35 Kg/sq.mt. as dire.
By eng. Incharge in c.m. 1:6 for super structure elevation.
45 Rmt 4950

11
53 2 Making connection to ex. MH. In running sewer line at any
convinent time when manhole is found empty all damaged portion
shall be repaired as per instruction etc. comp.150 mm to 300 m
dia
160 No. 320
54 2 Making Water connection from exi.Muni. Water line 250 No. 500
55 2 Supplying , erecting, testing, and commissioning of Submercible
pump set of 1.5 H.P. of Standard make against the total
monometric head of 15 mt. as per specification incl. motor starter
single phase preventer / liquid level controller G.I. fitting check
valves etc. comp. as dire.
9200 No. 18400
56 5.00 Providing and fixiing M.S. Fan clamps type 1 of 16 mm dia M.S.
bar bent to shape with hooked ends of R.C.C. slabs during laying
incl. painting the exposed protion of loops, all as per standard
design complete.
79.2 No. 396
57 300.00 Providing throating or plaster drip, grooves and moulding to Wall ,
R.C.C. chajja and slab. 25 Rmt 7500
58 50 Providing & Laying cement vatta 10 cm wide in c.m. 1:1 ( 1
cement, 1 coarse sand) laid in one layers finishing with a floating
of neat cement complete as dire. 17.8 Rmt 890
59 1000 Carrying out plinth treatment to post construction / exsiting
structure by spraying chenical solution for termite control
treatment incl. labour and materials consistant with I.S.I
specification.

66.6 Sq.mt 66600

60 10 Carrying out timber treatment to all wood work incl. drilling holes
and spreying oil based chenical solution on surface ot timbner
work for termite contorl including labour and materials etc. comp

34.9 Smt 349

61 5000 Conveyance charges of earth lime, murrum, building rubbish,
manure, garbage, sludge, excavated rock, fly ash, aggregate of
any kind etc. comp. upto 5 km lead.

140.38 Cmt 701900

62a 400 Providing special superior quality of Approved shape & size
Rubber Mould interlock pavers block 65 mm thick of M-35 grade.
Hydraulically pressed in machine of natural pigment or colour
suggested by Consultants for paving in Flooring , footpath etc.incl.
labour for fixing of blocks upto 50 mm th. sand bedding , levelling
watering. rate also incl.average 30 cm depth for excavation &
filling , carting away the debris / excavated material upto 5 km. &
cleaning the site etc. complete as directed.

429 Sq.mt. 171600

b 200 Providing , Supplying & Fixiing Shot Blasted Texture Finish , 60
mm thick Concrete Paver Block of Vyara make with ISI mark ( IS :
15658 :2006 ), M-40 Grade Compressive Strength , 200 mm x200
mm Size of Approved colors & Design as per Company
Specifications & Dir. Of engg. In charge / Consultants. Rate also
includes labour for fixing of Paver , upto 50 mm th. sand bedding ,
levelling watering. rate also incl.average 30 cm depth for
excavation & filling , carting away the debris / excavated material
upto 5 km. & cleaning the site etc. complete as directed.

1015 Sq.mt. 203000

63 200 Providing Kerbing of size 300x300x75 mm of M-25 with good
finishing rate incl.pointing in C.M. (1:1) & fixing in good line , level
& plumb etc. comp. 192 R.mt. 38400
12
64 50 Providing & Fixing Door closer - complete of Approved make to
wooden / Aluminium Doors as per direction of engg. In charge.
480 No. 24000
65 20 Providing & fixing Approved Make Glass Mosaic on Plastered
surface. Glass mosaic shall be of 25 mm x 25 mm size & 4 mm
thickness pasted on a net / paper sheet.Glass mosaic pieces are
mounted uniformly on the net / paper sheet. colour shade
combinations & Pattern as approved by Consultants.Rate includes
all material, Labour , Scaffolding etc. complete.

2569 Sq.Mt. 51380

66 25 Providing 2 mm thick Poly carbonate Gutter with necessary M.S.
Supporting Brackets. 400 Rmt. 10000
67 7 Providing Making & Fixing Identity Glow sign Board of suitable
size as per approved color-Designed Back Light Material fixed on
G.I. sheet Box of suitable size with concealed Light Fittings,
Necessary Scaffolding etc. complete as per direction of engg.in
charge.
1750 Sq.mt. 12250
68 145 Providing & Fixing Alluminium Composite Panel of approved
make of 4 mm thick Exterior Grade PVDF with coil thickness 0.25
mm & Frame work made out from Alluminium anodised section of
size 50x25 mm ( weight approx. : 0.57 kg./mtr.) having weight of
2.6 kg. for 15'-0 supported on Masonary/ R.C.C. with the help of
MS bracket fixed with Brick Fastener / Anchor Fastener & Groove
Filled with 789 weather fillent of Dowl corning corporation make.

3500 Sq.mt. 507500

69 7 Providing & Fixing Strucural Glazing with using 17 micron
Anodised approved color alluminium section as transium , mullium
of size 63mmx38mmx2mm with using 6 mm thick reflective
strucural glass of approved make color toughened & shade and
fixed with silicon sealant & spacer tape & at corner sealed with
neoprine foam dust & Air sealed gasket mirred including
scaffolding , cleaning of Glass etc. complete at all heights & lifts
all necessary M.S. or alluminium brackets suitably design for
openable window as per Architectural Drawing and as directed by
Engineer in charge. Grooves between the Glass shall be filled
with sealant of Dow corning- structural sealant 789. The entire
facade should be waterproof. The Mullions are to be connected to
bracket by SS-304 nut bolts. Measurement shall be given as per
the actual execution of work.

4729 Sq.mt. 33103

70 Box type metal letters forming composite box made from 1mm
thick stainless steel plate of grade 304 having brush finish of
following font size to be fixed at Main Gate in english and or
Gujrati and including fixing charges approved before fixing by
clent / consultant.
a 8 400mm high 1000.00 Nos. 8000
b 20 300 mm high 750.00 Nos. 15000
c 15 230 mm high 565 Nos. 8475

13
71 120 Providing and fixing eco-friendly light weight calcium silicate false
ceiling tiles having T egular edge & 15mm Thick Densified edges
on the Tile Periphery for Extra Strength The Light weight calcium
silicate ceiling tiles shall have, light reflection 85% non-
combustible as per B.S.476 part IV, 100% humidity resistance and
also having thermal conductivity 0.043° w/m KC. for the best
thermal Insulation. The Light weight calcium Silicate tile shall be of
approved texture Fine fissured/ Spintone/ Cosmos having NRC
value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent
of size 595X595 mm to be laid on true horizontal level suspended
inter locking metal grid of hot dipped galvanized steel sections
(galvanizing @ 120 grams per sqm including bothside) consisting
of main ‘T’ runner suitably spaced at joints to get required length
and size of 24X38 mm made from 0.30 mm thick (minimum)
sheet, 1200 mm centre to centre, and cross ‘T’ of size 24X28 mm
made out of 0.33 mm (Minimum) sheet spaced 1200 mm along
spaced between main ‘T’ at 600 mm centre to centre to form a
grid.

1730 Sq.mt. 207600

b 120 Providing and fixing single layer water proof gypusm board 12.5
mm thick of the make New good Group Co.Ltd. or equivalent &
New good Group Co.Ltd. company sections using water proof
board of size 1220 mm x 1830 mm x 8.0 mm suspended by G.I
suspender of size 25 mm x 3 mm with intermediate channel of
size 18mm x40mm x0.80mm at 1220 mm center to center ceiling
section of size 40mmx 35mmx 0.55mm at 457 mm center to
center and perimetre chanel A of size 20mm x 27mm x 30mm x
0.50mm at edges & drops including paper taps and sofit cleat,
anchor fastener, scoch bolt connecting cleat joining compound top
coat on ceiling including making necessary opening for light fitting,
diffuser etc. complete as per detail drawing as directed.

704 Sq.mt. 84480

72 Providing and fixing 10mm thick multiwall Polycarbonate roof
sheets of approved make, on structural roofing / sky light
structures in shapes as per Architect’s drawing. The rate shall
include cost of scaffolding, screws, nuts, bolts and all necessary
fixtures and fastening etc. complete.
165.00 2345.6 sq.mt. 387024
73 120 Providing & making Standard make type Glass Brick Wall /
Element from color / plain Glass brick as per Selection & Direction
of Consultants/ Engg. In Charge.Work includes all Material , Labor
,Scaffolding etc. complete.
135 No. 16200
74
Manufacturing,testing ,supplying loading,,transporting to work
site,loading unloading lowering in trenches,laying and jointing
RCC NP3 class pipes in C:M 1:1 including all jointing materials
such as cement,sand,hemp bitumen as directed testing the pipe
line to a head of 1.5 mt and hydraulic test as directed etc comp.

a 10 300 mm internal diameter 690 Rmt 6900

14
75 1
Constructing BP type catchpit of size 0.60 x 0.60 mt depth up to
0.75 including excavation BBCC(1:5:10) 23 cms thick brickwalls in
c:m (1:6) with 40 mm thick IPS flooring in the proportion M15 at
bottom and 20 mm thick cement plaster inside the catchpit in the
prop of c:m(1:3) without jali etc comp as directed
1220 No 1220
76 1 P/F FRC catchpit Jali with frame 600 mm x 600 mm clear opening
etc comp as directed by engg.in.charge 1550 No 1550
77 Dismantling work
Demolition of brick masonry ( it includes both side plaster of
a 5 wall)and stone masonry in cement mortar including stacking of
servicable materials and disposal of unservicable materials with
all lead and lift. 346 Cu.M. 1730

b 3 Demolition of RCC work including stacking of servicable materials

and disposal of unservicable materials with all lead and lift. 665 Cu.M. 1995
Removing & Scrapping of Old deteriorated Plaster of any
c 200 thickness from Masonary / R.C.C. member including stacking of
serviceable material & disposal of un serviceable from site of work
with all lead & lift. 12.3 Sq.M. 2460
78 PERCOLATION WELL
a 66 Boring and Sinking 30 cm. Diameter. Percolation well 760 Rmt 50,160
b 1 Soak well around 5.0 m. dia. X 5.0 m. liquid depth 130,400 No. 130,400
c 1 Brick masonry collection cum filtration tank around soak well 34,500
34,500 No.
15 cm. diameter strainer pipes (Johnson make) having slot size
d 18 32,940
1.5 mm x 57 mm (72 slots in one line) in the casing pipe
1,830 Rmt
Supplying, fitting, fixing and lowering 30 cm. diameter strainer
e 1 pipe 1.2 m long (Johnson make) having slot size 1.5 mm x 57 mm 10,000
(72 slots in one line) 10,000 Rmt
Providing and lowering 15 cm size M.S. (3 m long) bail plug to the
f 1 3,800
bore hole. 3,800 Set
Supplying, lowering, fitting, fixing and joining with Strainer, 15 cm.
g 30 35,250
diameter M.S. Pipe of minimum 5.40 mm wall thickness
1,175 Rmt
Cement ceiling the saline zone as per logging report and as
h 1 10,265
directed by the employer. 10,265 Job
Supplying, washing and shrouding with approved gravel, the
annular gap between the casing pipe and the remaining annular
i 12 22,860
space to be filled in with puddle clay (for which no measurement
with be taken and paid for ). 1,905 Cumt
Hire and labour charges for necessary tools and plants for
j 1 14,945
conducting proper tests for percolation water, 14,945 No.
BORE WELL TURNKEY SYSTEM:‐

15
 Supply installation, testing, commissioning of Bore well complete
job, including drilling 6" bore hole, casing pipe MS c‐class,
plumbing pipe tata‐c class, testing of yield test report, including
water testing report, submersible pump to be installed in the tube
well of required indicated capacity and head as per relevant IS for
Bore water lifting
with suitable submersible vet type, water cooled, squirrel case
motor conforming to IS 9283, working of 3‐phase, 50Hz +/‐ 3%
415 VAT +/‐ 10%, AC supply 2900 RPM synchronous speed with
79 1 10mtr. copper conductor flat cable from pump to starter panel with 400000 job 400000
cables and termination ( all supports clamps pipe fittings
mechanical seal, bearing, bush, strainer, etc. comp., Casing C.I.,
S.S. CF8M impeller, bronze casing, wearing and bearing bush,
TC mechanical seal, S.S. bearing, S.S. shaft with sleeve, S.S.
strainer, and M.S. mortar along with water guard, single phase
preventer with all cables of appropriate size control and
instrumentations, switches, testing, and installation client /
Consultant's instructions ( Make as Per R & B Sor or App. Eq.)

Capacity of Each pump set : (100 CU.MTR/DAY.)

Depth : APPROX 250 to 500 ft.
Total 36322489.1
Rs.
ELECTRICAL WORKS
1 Internal Wiring

Point wiring for Light / Bell with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1
KV grade FRLS PVC insulated multistrand copper wires,
in following type of pipe to be erected concealed in/ on
surface on wall/ceiling complete with 6A Modular type
switch / bell push & accessories and earth continuity of
1.1 180 following type, erected on PVC / Metallic box, single 420 Pt
mounting base frame covered with textured/metallic front
plate modules erected on / in wall / ceiling as per pipe
erected, with necessary Lamp holder/ceiling rose /
H.D.Connector as directed. with (a) with medium class
Rigid PVC pipe and accessorie Cat III
75600
Secondary point wiring of light point with 2-1.5sqmm & earth wire
of 1.5sqmm ( Green ) both are of ISI marked 1.1KV FRLS PVC
1.2 120 insulated in medium class rigid pipe using same 6A one way 120 Pt
switch (a) with medium class Rigid PVC pipe and accessorie Cat
III
14400
Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm
& earthwire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV
grade FRLS PVC insulated multistrand copper wires, in following
type of pipe to be erected concealed in / flushed on wall/ceiling
,complete with 6A Modular type switches and following type of
accessories erected on PVC / Metallic box, single mounting base
1.3 6 frame covered with textured / metallic front plate modules erected 530 Pt
on / in wall / ceiling as per pipe erected. with necessary
batten/angle holder or ceiling rose or H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and accessorie Cat III

3180

16
 Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm
(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC
insulated multistrand copper wires, in following type of pipe to be
erected concealed in / flushed on wall/ceiling complete with 6A
Modular type switch and hum free EME four or more step type
electronic fan regulator with separately mounted and accessories
with earth continuity of following type erected on PVC / Metallic
1.4 75 box, single mounting base frame covered with textured/metallic 600 Pt
front plate modules erected on / in wall / ceiling and fan box with
hook in slab as per pipe erected. with necessary ceiling rose /
H.D.Connector as directed. (a) with medium class Rigid PVC pipe
and accessorie Cat III

45000
Point wiring for Individual Plug with & earthwire of 1.5 sq.mm
(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated
multistrand copper wires, in following type of to be erected
concealed in / on surface of wall / ceiling complete with Modular
1.5 type switch & 5 pin Plug erected on PVC / Metallic box covered
with appropriate front plate modules erected on / in wall / ceiling
as per pipe erected with following type of accessories.(a) with
medium class Rigid PVC pipe and accessorie Cat III
1.5.1 75 [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire 445 Pt 33375
1.5.2 12 [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire 670 Pt 8040
1.5.3 3 [III] For 16A Plug with 2-4 sq.mm Cu. Wire 790 Pt 2370
Point wiring for Looped Plug with 6A Modular type switch & 5 pin
socket erected on PVC / Metallic box, single mounting base frame
1.6 50 covered with textured / metallic front plate modules erected on / 240 Pt
in wall / ceiling with following type accessories.Cat III
12000
Providing following type of Modular Type Accessories mounted
with pvc / metallic box, single mounting base frame covered with
1.7 textured / metallic front plate , modules erected with necessary
connection. As desired by Engineer In charge

1.7.1 27 (3) Two Pin/RJ-11 Telephone Socket Cat- III 160 No 4320
1.7.2 3 (4) TV Co-axial Socket outlet 160 No 480
1.7.3 33 (8) Modem Jack for Computer Open RJ-45 160 No 5280
1.7.4 10 (19) Modular Indicating Call Bell 330 No 3300
Supply, Installation, testing and connection of LED type FOOT
LIGHT suitable in rooms (indoor type ) Similar to Philips Model
No. 30974 / Wipro-LT 54 -002-XXX-RD-XX W / Bajaj BGST 01 01
1.7.5 18 WW.The Price inclusive of anodized GI box .The LED colour will 1915 No
be as per instruction of Engineer-in-charge.
34470
1.8 9 Supply and erecting Decorative call bell Ting-tong box type 250 70 No
volts complete erected 630

Providing & erecting Switch board for Computer or electric

apparatus consisting of following items in single board erected on
PVC / Metal board with 3 mm thick PC (Polycarbonate) / Acrylic
1.9 33 sheet erected as directed 1140 No
1 no. 6A/16A universal plug-switch combined.
4 nos. 6A Switch
4 nos. 6A 5 pin Plug [B] For Modular Type Accessories
37620

17
 Providing and erecting ISI mark Medium class RIGID PVC PIPES
of following size complete to be erected on/in wall or ceiling
erected with necessary PVC fittings & Junction boxes fixed with
1.10 adhesive solution & Clamps with following dia of pipes, in
approved manner as directed ( if required )

1.10.1 520 (b) 25 mm ( for data and voice ) 32 Mtr. 16640

1.10.2 150 (c) 32 mm for TPNMCBDBs wiring mains 53 Mtr. 7950
Supplying & erecting M.S. Box having 16 Gauge painted with red
oxide or Heavy duty PVC box erected flushed on wall or
1.11 7 concealed in wall with necessary plastering & finishing as directed 110 No
of (d) 250 mm x 300 mm x 75 mm size.
770
2 MAINS WIRING
Mains with 1.1 KV grade FRLS PVC insulated ISI marked
stranded Copper conductor wire in following type of pipe to be
erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm
2.1 copper conductor FRLS PVC insulated stranded wire of green
colour for earth continuity of following size

2.1.1 320 (a) 2 wire 1.5 sq. mm 60 Mtr. 19200

2.1.2 600 (b) 2 wire 2.5 sq. mm 80 Mtr. 48000
2.1.3 225 ( c ) 2 wire 4.0sqmm for A/C point 110 Mtr. 24750

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor
2.2
FRLS PVC insulated stranded wire of green colour for earth
continuity of following size for TPNMCBDBs from main panel (e)
in existing pipe 32/40mm size pvc MMS

2.2.1 50 (h) 4 wire 6 sq. mm for G.F. and F.F. LDBs 240 Mtr. 12000
2.2.2 60 (i) 4 wire 10 sq. mm for A/C DB 400 Mtr. 24000
3 Telephone & TV wiring

Supplying & erecting Delton or approved make Telephone Cable

electrolytic copper conductor PE insulation twisted in two pairs, &
wrapped with FRLS PVC tape & sheathed with FRLS PVC or
3.1 510 HFFR outer Jacket suitable for telephone wiring & confirming to 14 Mtr.
C-DOT erected in existing pipe. of following size of conductors &
nos.of pairs. With necessary connections. (Conductors size :
0.5mm unarmoured 2 pairs )
7140
3.2 50 same as above but for 4) Five Pairs 30 Mtr. 1500
Providing & Erecting approved make following size of TV Co-axial
flexible cable comprising inner conductor of solid bare copper
insulated with Foam PE & Secondary conductor made of poly -
3.3 60 Aluminium film bonded Al. Braids @ suitable coverage overall 30 Mtr.
sheathed with black PVC insulation. ( a ) RG 6 WIRE
1800
Supplying & erecting approved make LAN cable of following size
3.4 650 40 Mtr.
in existing pipe as per direction ( CAT- 6 ) 26000
3.5 1 Supplying & erecting approved make 24 PORTS LAN Switch for 3500 No
Cat- 6 3500
3.6 1 Supplying and erecting of approved make 24-ports Patch panel 5500 No
for Cat-6 5500
3.7 1 Supplying and erecting approved make 6U mounting rack with all 3850 No
accessories 3850

18
 Providing & erecting main Distribution (MDF) indoor type, back
3.8 1 mounted frame suitable for 20 pair 1000 No
1000
3.9 1 Providing & erecting main Distribution (MDF) indoor type, back 600 No
mounted frame suitable for 10 pair 600
Supplying, erecting, commissioning and testing EPABX CMOS
microprocessor based system having common features With
remote programming & remote dialling having following other
common features. (Accord Matrix or equivalent approved make)-
Auto Call Disconnector- (Incoming - Local- STD) with
programmable timing- External Call forward with DOSA- Walk
in Class of service & trunk reservation- Boss ring & call back on
No Reply last caller recall CLI- Hot Line with Delay & with No.-
3.1 1 Unsupervised Conference- Serial DISA ( DISA with option to dial 12500 No
another No. if Extn. is No Reply)- Programming Flexibility of all
features related to timer( 41 Timer)-10 Different group of out
going call restriction like 95, 97, 98 etc.Having following
capacity. (E) 4 incoming junction line & 12 extensions.

12500
Supplying & erecting push button type telephone instrument
having speaker phone Caller ID & hands free dialling system & 30
3.11 10 memories with display system 790 No
(a) Single line BPL / SONY/ BEETEL or equivalent make
7900
4.0 Switchgears , Panel and MCBDBs
Approved make Four pole moulded case circuit breaker having
breaking capacity ICU of 35 KA. at 415 V. having normal current
rating up to 125A. with Fixed thermal & magnetic release suitable
4.1 1 to work on A.C.supply 50 c/s. with all internal connections & 8200 No
complete erected in existing 16 G.M.S. housing . ICS=100% of
ICU only Cat III

8200
Approved make Earth fault Relay suitable to mount with inter
connection to moulded case circuit breaker having CT ratio &
MCCB rating as following along with shunt trip 220V AC. with all
4.2 1 internal connections & complete erected in existing M.S.housing.. 5080 No
(2) 125 A -200 A , CT Ratio 1/200
5080
Providing and erecting M.S.Housing fabricated from 16 S.W.G.
CRCA sheet with duly powder coated in Siemens grey colour to
4.3 1 accommodate above items MCCB and E/F relay . 1250 No

1250
4.4 POWER DISTRIBUTION BOARD

19
 Design, fabrication, assembling, supply, installation, testing and
commissioning of cubicle type LT panel suitable for 415 V 3
phase, 4 wire 50 Hz AC supply system fabricated in
compartmentised design from CRCA sheet steel of 2 mm thick for
frame work IP 42 and covers,3 mm thick for gland plates i/c
cleaning and finishing complete 7 tank process for powder coating
in approved shade, extendable type TPN aluminium alloy busbars
of high condectivity, DMC/SMC busbar supports, with bottom
base channel of MS section not less than 100mm X 50 mm X 5
mm thick, entire panel shall have a common copper earthbar of
1 size 25mm X 5 mm at the rear with 2 Nos. earth studs, solid 65500 No
connection from main busbar to switchgears with require size of
aluminium busbar & control wiring with 1.5 sqmm FRLS insulated
copper conductor cable, cable alleys, cable gland plates i/c
accessrories as per specification and providing switchgears,
metering instruments etc. for follwing panel.

65500
A. Incoming Feeder:-
(i) 1 Nos. of 160 Amps, 415V, 35kA, FP MCCB with Thermal
magnetic Based releases having O/C & S/C along with following
along with following
(ii)LED type Indicating Lamp with suitable rating 2A SP MCB:- 1
Set comprise of R,Y,B)
(iii) Digital type 3 phase Multi function Meter with suitable rating of
MCB & 3 Nos. of single core epoxy resin cast type CTs of 200/5
Amps, 10 VA, CL 1.0 ratings -2 Sets.

B. Busbar:-
200 Amps, 415 V, TPN Aluminium Busbars with Heat shrinkable
color code insulation sleeves.
C. Outgoing:-
(a ) 7 nos. of 63 Amps, 415V, 10kA, FP MCB
( b ) 5 nos. of 40Amp DPMCB
( c ) 40Amp FP MCB incomer and 20Amp SP MCB 3 nos. per
phase controlled by 32Amp TP contactor and approved make
Segment time switch suitable for 230V+10%16A. floating contacts
with 24 hour dial having15/30 min. segments with early manual
override switching for on & off without influencing the program
sequence with quartz time switch With power reserve.

4.3 MCBDBs and MCBs

Supply, Assembling, grouting, levelling Connecting & testing D.B
of IP 43 of specified make.
Providing and erecting Sheet Steel powder coated MCB
distribution board - flush / surface mounted fitted with busbar,
neutral link, earth bar and DIN rail, confirming to IS 13032 and BS
5486-1986 without MCB to house appropriate nos. of MCBs.(The
DBs should be used of same company of MCB to be used)

4.3.1 6 8 ways SPNMCBDB double door type 990 No 5940

4.3.2 6 8 ways TPN MCBDB double door type 2920 No 17520
Miniature circuit breaker single pole 6A to 32A suitable to operate
on 240 V A.C. system and having breaking capacity 10 KA to be
4.3.3 100 erected in existing box. confirming to IS 8828/1996 with ISI Mark 115 No
.Cat III
11500

20
 Providing & erecting 240 V MCB double pole switch for motor &
inductive load (C Curve) having 10 KA breaking capacity &
4.3.4 12 confirms to IS : 8828 in existing box having (A ) 6 to 32 Amp 305 No
capacity .Cat III
3660
Providing & erecting 415 V MCB Four Pole for Motor & Inductive
Load (C Curve) having 10KA breaking capacity & confirms to IS
4.3.5 5 :8828 in existing box having ( c) 63 Amp capacity 750 NO

3750
Approved make ELCBs / RCCBs conforming to IS: 12640 and
having sensitivity of 30 mA and Short Circuit withstand capacity of
6 KA and suitable for operation on single phase 240 V. having
4.3.6 characteristic of quick action & tripping with all advance feature &
do not incorporate any electronic component. for following Max.
rating erected as directed.Cat III

4.3.6.1 2 (i) 25 Amps.DP 2300 No 4600

4.3.6.2 9 (ii) 40Amps. DP 2610 No 23490
4.3.6.3 6 (ii) 63Amps. DP 2600 No 15600
Mains with ISI marked, 1.5KV grade electrolyte multi stranded,
annealed copper conductor with heat resistant PVC insulated
conforms to IS 694, IEC - 227 erected in existing pipe of following
4.4 20 size (Specifically for mains supply switch to Meter ) with 235 Mtr.
required size of copper lugs, nuts and bolts if required.(h) One
wire 25.00 sq. mm

4700
Providing & erecting PVC Corrugated Flexible Conduit with
4.5 12 required nos. of coupling, PVC bushes, Check-nuts etc. complete 45 Mtr.
of (5) 50 mm size. 540
5.0 EARTHING
Providing and erecting required size HOT deep Galvanised iron
strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel
5.1 40 board, Motors etc. using proper clamp. 90 KG

3600
Providing and erecting HOT deep Galvanised iron strip wire 8 to
5.2 40 16 SWG. 90 KG
3600
Supplying & erecting in earthpit of minimum bore dia. 225mm size
ASH or approved make Safe Earthing Electrode consisting
Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion
free G.I.Pipes having Outer pipe dia of 80 mm having 80-200
Micron galvanising, Inner pipe dia of 40 mm having 200-250
Micron galvanising, connection terminal dia of 14 mm with
constant ohmic value surrounded by highly conductive compound
5.3 3 with high charge dissipation suitable for panel earthing.[A] For 9100 No
electrical installation up to 440 V
Length of Pipe - 1 Mtr
Back filling compound - 1 Nos. of Bag of 15 Kgs.

27300
6.0 CABLES
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable
multistrand Aluminium conductor for 1.1 KV. to be laid on wall
with necessary clamps or in existing trench / pipe of following size
of cables.
6.1 50 (B) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) 350 Mtr. 17500
6.2 250 (b) 4 core 6 Sq. mm 130 Mtr. 32500

21
 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
6.3 cable multistrand Copper conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench / pipe
at road crossing or floor of following size of cable.
6.3.1 30 (A) 4 core 2.5 Sq. mm 260 Mtr. 7800
6.3.2 60 (A-1) 4 core 4 Sq. mm 350 Mtr. 21000

7 CABLE END TERMINATION

Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete with
out going tails, insulating tape etc for following size of cables.

For Aluminium cable

7.1 4 (B) 3 & 1/2 core 35/50 Sq. mm 80 No 320
7.2 25 (b) 4 core 6 Sq. mm 40 No 1000
For Copper cable
7.3 3 (A) 4 core 2.5 Sq. mm 35 No 105
7.4 10 (A-1) 4 core 4 Sq. mm 35 No 350

Solderless crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool
& connected to switchgear terminals with brass/cadmium plated
nut bolts in an approved manner.

7.5 100 (A) 1.5/ 2.5/4/6 Sq.mm 5 No 500

7.6 4 (D) 25 Sq.mm. 15 No 60
7.7 10 (E) 35/50 Sq.mm. 20 No 200

Solderless crimping type Copper lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &
7.8 50 8 No
connected to switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. (A) 1.5/2.5 to 6 Sq.mm
400
7.0 CABLE TRENCHES
Making trench in soft soil of suitable width of 90 cms deep for
laying cable or locating the fault all over the run and backfilling
7.1 250 the same and making the surface as normal ground. 40 Mtr.

10000
Covering of cable with second class bricks or cement tiles laid
cover the cable crosswise & also on both sides with covering of 7.
7.2 230 5 Cms. layer of sand above & below cable (16 bricks per meter) 130 Mtr.

29900
7.3 Supplying following size of Light duty “A” Class G.I . Pipe &
erecting as directed by Engineer-in-charge.
7.3 ( a 5 (A) 25 mm dia 160 Mtr.
) 800
7.3 ( b 5 (B) 50 mm dia 280 Mtr.
) 1400
8.00 LIGHT FIXTURES AND FANS
Supply , Installation, testing and commissioning of pre-wired,
fluorescent fitting / compact fluorescent fitting/LED fitting/MH
fitting/post top luminaries etc of all types, complete with all
accessories and tube etc. directly on ceiling/ wall, including
connection with 1.5 sq. mm FRLS PVC insulated, flexible, copper
conductor, single core cable with flexible conduits and coupler and
earthing etc. as required

22
 Supplying and erecting decorative recess mounting type 2'X 2' LED 36w 4000 No 180000
LED luminaire caving in effect, with low glare UGR < 19 rated diffusers,
8.1 45 Clutter free,complete Electronic Ballast ,P.F. >0.95 , THD <10% , CRI >
80,CCT 4000K, 3600 Lumens, IP-20 Ingress protection

705 No 42300
SupplyinganderectingenergyefficientSlimLEDBatten22W(1200mm)lightin
anddecorativeendcapswithIndustrybestlightoutput with glare free
8.2 60
illumination ,Robust HPF LED
driver,Efficacy>85Lumens90/Watt,Protectedfromdustandsects

Supply,Installation,Testing and Commissioning of Circular LED

downlighter of following Cat No :-
(1) RECESS MOUNTING :- Philips DN 193 B/ Cromp LCDD-15W
/ Bajaj BZSLO 15W WH / Wipro LD 82-121- XXX-60-XX 12W
8.3 18 1915 No
(2) SURFACE MOUNTING :- (i) Crompton-LCDSPL-R-15-CDL /
Bajaj BGCML X 12 01 NW / Wipro LD80-101-XXX-60-SM- 12W
.Contractor has to supply Colour i.e. Warm white / Cool White as
per Client requirement
34470

Supply and erecting 300x300mm size LED Square

Surface panel with powder coated finished in white
8.4 20 housing light fixtures of Crompton make Cat.no: 2650 No
LCDSPL-S-CDL or Philips make Cat.no: SM518C LED
16S ( cirrus mini )
53000
Supply and erecting surface round down lighter OF Philips make
8.5 60 Cat no: DN092B LED 10S ULTIMA Green LED light fixtures 1350 No
81000
Supply, Installation, assembling, connection, testing and
commissioning of LED light fixture as per Philips BN550
8.6 10 WLED6K-6500K / Bajaj Trilux Onperla / Wipro Garnet Magma 1600 No
7W.Contractor has to supply Colour i.e. Warm white / Cool White
as per Client requirement.
16000
Supply and erecting Sleek LED mirror light with diffuser 10w LED
8.7 20 surface mounting of Crompton make Cat no: LL-10-CDL Linnet or 1350 No
equivalent 27000
Supply and erecting of Philips make Endura LED Bulkhead fitting
8.9 10 Cat no: WT202W LED 6S PSU S1 PC or Bajaj Cat no: BIBDP 1850 No
10W LED 18500
Providing & erecting Approved make Power Saving 50 Watt
Ceiling Fan with double ball bearing ISI mark with Condenser 230
volt A.C. 50 Hz 1200 mm sweep complete having 3blades with
aluminium blades with , canopy & suitable lenght of down rod
9 75 erected with 24/ 0.2, 3 core flexible wire with earthing.(Make shall 2070 No
be approved by Engineer in charge))Orient energy star, Havells
ES-50,Crompton high speed +

155250
Supplying & erecting approved make low noise decorative
exhaust fan having size 200mm with 1350 RPM with square frame
10 12 ABS body with inbuilt lowers & square frame. 1990 No

23880
11.0 EXTERNAL LIGHTING

23
 Supplying & erecting sintex make SMC press moulded
composite FRP. loop-in, loop-out approx. 2mm thick box
complete with bakelite connector strip 4way & hinged doors
having locking arrangements with mounting clamp with nuts, bolts
11.1 10 & washers suitable for erection on wall ( c)150mm x 125mm x 550 no
100mm [deep]
and 3 core x 1.5sqmm round flexible wire from box to light
fixtures .
5500
Streetlight luminare Pressure die cast aluminium housing with
heat resistant toughened glass & IP66 protection. 30w equivalent
11.2 8 to crompton make LSTO-30-CDL 6500 No

52000
Supplying Steel tubular pole (Swaged) confirming to IS - 2713
(Part-II) 1980. Manufacturing process of steel tubular pole should
be as per IS specification. Basic steel tube should be ISI Marked.
Pole should be painted by one coat of Zinc comet Primer and two
coat of Aluminium /approved paint to be erected on / in existing
Foundation. The length of poles are as below. (A) 7.5 mtr. Long
Swaged Steel tubular pole (i) pole as per IS code 410-SP-4 with
11.3 8 300 X 300 X 4 mm base plate. (Approximate Pole weight 67 Kg) 8500 No
For burial erection with M.S. Base plate 300 X 300 X 16 mm for
pole, Suitable for mounting on surface of foundation with
foundation bolts, with required stiffeners welded with pole and
duly painted.

68000
Providing and erecting ( on wall or pole ) Street light pole bracket
consisting of" B" Class MS .pipe of 4.2 cms. outside dia.complete
with suitable MS sleeve tubing of required size and length suitable
for 76.5mm/80mm/require size of pole top having nuts and bolts
for fixing the brackets and having spread of 0.5 mtr. Length with
110 deg.with vertical plane and suitable welded stiffener reducer
11.4 8 and nipple with checknut complete painted with one coat.of Red 525 No
oxide / PU base primer and two coats of Aluminium / PU paint.
paint with following nos of arms. [A] Single Arm bracket 1.0 Mtr

4200
Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC
from bottom including excavation for the pole of size 60 x 60 x 120
cms. Deep in below ground level with plinth of 45 cms x 45 cms(or
11.5 8 45 cms dia x 45 cms) high upper ground level with necessary 1300 No
curing and finishing in approved manner. ( for 7.5 & 8/8.5 mtr
pole)
10400
Pipe type earthing having 150 cms.long and 2.5 cms. dia.
galvanised iron pipe with coupling and buch buried in specially
11.6 8 prepared earth pit complete with necessary 8 SWG earth wire. 430 E.a.

3440
Supplying and erecting min IP65 aesthetically designed sturdy
70W SONT Posttop with housing made ofpowder coated die cast
alumunium. Light distribution should be symmetric 360° & for
glare free lighting posttop should be with Polycarbonate/ diffused
toughned glass or UV stablised polyethylene bowl. Philips make
11.7 2 6500 E.a.
HPS360 or Schreder Jasper 70W SONT or Disano Polar 1502
70W SON.
as erected for gate light.

13000

24
12.0 MISC
12.1 2 Automatic water level controller with sensors and wiring 4500 No 9000
Providing and erecting 3 star and above rated approved make
split air-conditioning unit consisting of condensing unit with fan
motor, hermetically sealed rotary compressor with accessories
etc. duly connected separately erected evaporating unit and
blower motor with its accessories by means of proper insulated
copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand,
12.2 12 Gas Charging & Internal Copper Wiring & Remote Control) Makes 42500 No
:-3-STAR model of DAIKIN/O GENERAL / TRAIN/HITACHI
/MITSUBISHI AND 5-star model of PANASONIC with cu
condensor for (b) 1.5 ton capacity

510000
Extra charges for the Items beyond standard length For Single
phase Split A.C. Machine insulated pair of soft, copper tubing
12.3 30 including power and control cable up to 1.5 TR capacity 850 Rmt

25500
Providing & erecting water cooler having storage capacity 150
Ltr.& cooling capacity 150 Ltr.per hour @ an ambient temp of 450
C. The outlet temp. of the water should drop by 150C within a
hour, The water cooler should be comprising of hermetically
sealed compressor, fan motor, condensing unit, water tank
12.4 3 surrounded by evaporating, coil, thermostats, relay etc.complete 54500 No
with necessary inlet & outlet connection. The body of water cooler
will be made from Stainless Steel. ( Make:-USHA/BLUE
STAR / VOLTAS ) ONLY

163500

Supplying and erecting water filter cum purifier with ultra violate
12.5 3 5290 No
technology. (Ureka forbes , KENT, PURE, Zero B )
15870
13.0 CCTV WORKS
13.1 5 Supply ,installation,testing and commissioning of 1/3" CMOS , Image 6950 No
Size:1280x960 , 0 Lux, 3.6mm Lens , Encode : VBR/CBR, Audio:No, 10-
20mtr IR Distance , IP66 Water Proof . 34750

13.2 15 Supply,installation, testing and commissioning of 1/3" CMOS , 1280x960 , 8200 No

0 Lux, 3.6mm Lens , Encode : VBR/CBR, Audio:No, 10-20mtr IR 123000
Distance , IP66 Water Proof .
13.3 3 Supply ,installation,testing and commissioning of 8CH IPC input @30fps 7850 No
1080P/ 960P/ 720P , Playback: 4CH simultaneously playback ,
OUTPUT- HDMI & VGA 1920 x 1080,Network Protocol: TCP/IP, UDP, 23550
DHCP, DNS, PPPOE, DDNS

13.4 1 Supply ,installation,testing and commissioning of Hard Disk 3TB, 24*7 7850 No
Reliability for video streaming 7850
13.5 3 Supply ,installation,testing and commissioning of 8 PORT POE SWITCH 2200 No
10/100 6600
13.6 3 Supply, Installation , testing and commissioning approved make 21"' TFT 8100 No
LCD Monitor 24300
13.7 450 Supplying & erecting approved make LAN cable of following size in 40 Mtr.
existing pipe as per direction ( CAT- 6 ) DILINK or MOLEX make 18000

13.8 Providing and erecting ISI mark Medium class RIGID PVC PIPES of
following size complete to be erected on/in wall or ceiling erected with
necessary PVC fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner as directed ( if
required )

450 (b) 25 mm ( for CCTV ) 32 Mtr. 14400

25
 LIASIONING WORK :-Charges for doing liasioning work for
obtaining the necessary clearances rom the Electrical inspector /
competent Authorities for the total Electrical installation, co-
ordinating with various agencies. All necessary drawings,
calculations, test certificates, etc. as required by these authorities
shall be prepared and furnished by the EPC Vendor. Any
14 1 modification/rectification as required by these authorities shall be 20000 Job
carried out by theEPC Vendor at free of cost. The fees required to
be paid to these authorities for inspection shall be borne by Owner
on production of documentary evidences.

20000
15.0 Passengers Elevator
Supplying, Erecting, Testing & Commissioning the passenger / stretcher
lift having following main features:
[1] MRL GEAR LESS LIFT DRIVE comprising of High Starting torque Lift
duty 3 phase 440 V A. C. Permanent magnetic synchronous motor of
proper rating with high efficiency shall be used.
[2] Micro processor based / PLC, ACVVF, vector control drive with
encoder feedback closed loop system shall be used for lift car and door
operation which shall be full collective selective operation hall call
demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with
overload and phase reversal relay and safety controls.

[3] Car with M S platform with bracings of adequate size and to sustain
the impact load cabin + passenger with safety factor of fire for steel and
side panels of Stainless steel of sheet of grade 304 duty. Car ceiling will
be S.S. finishes with aesthetic appearance with LED ceiling lights. Car
flooring shall be of anti skid PVC with choice of colour of engineer in
charge. Car doors shall be of stainless steel grade 304, hairline finish
with centre opening / telescopic automatic doors. Car panel will also be
S.S. 304 finished with emergency stop device, mechanical door safety
device, facility of auto/ attended mode. All car panel buttons and all floor
switches must be with brail language as per lift act.

[4] All landing doors shall be fully automatic centre opening/ telescopic
opening made of hairline finish steel grade of 304 with key holes and
infrared curtains with Unlocking facility from outside.
[5] Appropriate battery operated emergency light in the car along with
alarm switch shall be provided.
[6] Digital scrolling indicator system for up-down arrow along with floor
position indicator shall be provided inside the car and at all floors.
[7] Full height infra red curtain with multiple criss / crossing light beams
shall be provided.
[8] Automatic Rescue Device (ARD) shall be provided accordingly of
passenger capacity.
[9] Audio visual indication in the lift car showing over loading shall be
provided such that doors kept open till excess load is removed.

26
 [10] Spring buffers/PU Buffers shall be provided.
[11] Car fan with automatic sleep timer shall be provided.
[12] Voice annunciater with suitable music shall be provided in lift car.
[13] Self diagnostics system for operational and safety parameters shall
be provided in control panel.
[14] Mechanical over speed governor, door key holes in the floor doors,
fireman switch shall be provided.
[15] Lift machine hoisting arrangement in the lift machine room and
monkey ladder for lift pit should be provided by the lift agency, along with
the other steel structure works, foundations for the machine etc…
[16] In the hoist way fascia plate shall be provided without any extra cost,
where ever required as / if directed by engineer in charge.

[17] Permanent wiring in lift machine room and lift well with proper
numbers of light points, with fixtures, exhaust fan and plug points shall be
provided by the agency. Power supply of 3 phase 440 V shall be made
available by department in lift machine room.
[18] Any civil/ electrical works for additional and alteration in lift shaft and
machine room related to erection of lift shall be made by lift agency
without any extra cost.(granite/marble fixing around all landing door
openings are not in lift agency’s scope.)
[19] Agency has to provide all working drawings and documents and
liaison services for obtaining all necessary permission from lift inspector
and other authorities.

[20] As per statutory requirement of Got. Of Gujarat lift & escalator act
2000, lift agency has to provide
1. Car top safety barricade
2. Push & talk communication system.
3. Fireman's switch operation at Ground Floor

15.1 1 8 passengers .Basement, Ground plus 2 upper floor(Machine Room 2067500 No 2067500
Less) with Rated Speed of 1.0 m/sec with micro price/PLC control and
ACVVVF. drive - Premium category

Total
Rs. 4686090
LANDSCAPING WORK :
1 50 Development of lawns, hedges, flower beds etc.
at the locations shown in the drawing and as
directed by the Engineer. Comprising of the work as detailed
below.
175 Sq.mt. 8750
a) Loosening the soil upto a depth of 45cm
removing the grass roots weeds, stones, brick
bats, concrete etc., and disposing the rubbish at
the place shown by the Engineer.
b) Supplying and spreading good quality Farm
Yard Manure at the rate of 0.5 cu.m/I00 sq.mt. of
lawn area. The farm yard manure shall be free
from soil clods, grass roots, etc and shall be well
rotten. The manure shall be mixed well in the top
150 mm layer of soil and the area shall be
leveled, watered and rolled as directed by the
Engineer. After the area is made weed free,
planting of grass cutting shall be done.

27
 c) Supplying and planting of cynodon dactylon
(Dhoob grass) or pospalune SPP. Planting shall
be done at a distance of not more than 50mm on
either direction.
d) Supply of flower seedlings, low shrubs plant
pockets, balbous plants, brick curbing,
preparations of edge walls, retaining walls and
planting the same wherever required as per the
instructions of the Engineer, including watering
the plants at the time of development.
Measurement of the above will be made in Sqmt.and paid for.

2 15 Provide good quality of soil (river silt) 360 Cmt. 5400

3 50 Maintenance of newly developed/ existing
lawns, hedges, garden etc. comprising the
following operations for one year from the hand
over to AMC. 60 Sq.mt. 3000
c) Supplying and planting of cynodon dactylon
(Dhoob grass) or pospalune SPP. Planting shall
be done at a distance of not more than 50mm on
either direction.
a) Watering every-day for first 30 days after
initial development arid thereafter twice in a
week and thrice in a week during summer i.e.
March to June
b) Weeding the lawns, trimming the hedges,
shrubbery, twice in a month or more as directed
by the Engineer
c) Rolling, mowing or cutting the lawns twice in a
month or more as directed by the Engineer.
d) Supplying arid application of farm manure of
approved quality at the rate of 1 cu .mt/100 Sq.
mt, area once in 6 months and leveling the
same.
e) Supplying and application of fertilizer / Farm
Manure as required and as directed.
f) Supplying and application of good loamy soil
of approved quality at the rate of 1 cum/100 sqm
area once in a year.
g) Supplying and spraying of pesticides,
fungicides etc. once in a month or more as
required.
h) Removal of dead Leaves, sweeping the
lawns, clearing the flower beds daily or as and
then required and disposing the rubbish etc., at
the place shown by the Engineer.
i) Any other job related to the maintenance of
lawns, gardens, flower beds, hedges etc not
covered above but which are necessary for
maintenance in the opinion of the Engineer.

28
 Supplying on site , Digging upto 1.50 mtr. Depth and
Planting of, with adequate precautions against mortality or
damage, and including all materials and operations
associated with planting successfully the following
indicative number of Trees / Shrubs / Climbers / Bamboos
4 as per dir. of consultants /authority, with a reasonable
standard of care and Maintaining for a period of Twelve
months

.Gulmohar, bumum,Champa,Karanj,kadamb,Tabebula etc.

a 150 as per dir. Of Consultants 220 No
33000

Planting of exoitic palm trees Digging of pits 2ft x 2 ft x 3 ft,

5 5 filling with good earth with mixing of cow dong and 1200 No
pesticide. planting the following plant of 4' to 10' height
stack it well, maintain it for 12 month 6000
Total
Rs. 56150

Fire Fighting Work :

SPRINKLER & HYDRANT SYSTEM - PART- A

SITC of fire main pump of having 2280 lpm @55 mtr head
1 suitable for automatic operation with ci body,brass impellor at
2900 RPM,415 volt,3 phase,50 hz, 40 hp ac supply.
1 275000 Nos 275000

SITC of fire main pump of having 180 lpm @55 mtr head suitable
2 for automatic operation with ci body,brass impellor at 2900
RPM,415 volt,3 phase,50 hz,5 hp ac supply.
1 100000 Nos. 100000
Control Panel for Fire pumps.

Supply, installation, fabrication, testing & commissioning of

3 common control panel for Electrical motor driven,Jockey & diesel
pumps with automatic and manual operation.
1 130000 Nos. 130000
1 Nos. 63A, 3P, MCB, 35KA.

1 Set of RYB indicating lamps with controlled by 3P, MCB, 4A

DOL starter with over load relay, single phase preventor &
indicating lamps with ON / OFF push buttons.

All the components shall be housed in a common cubical made of

16 swg. M.S. sheet with required stiffners (if required). The panel
shall be powder coated of approved colour both inside & outside.
The panel shall have both bottom & top cable entry provisions &
panel shall be mounted on Pedastal of 300 mm height.

1100 V Grade power / Control cables

29
 Supply, laying, testing & commissioning of Cable with aluminium /
copper conductor, XLPE insulated, extruded PVC inner sheathed,
FRLS outer sheathed armoured and PVC Sheathed overall 1.1
KV grade. The cables shall conform to IS 7098 part-II. Providing
4 end Termination of cables with supply of brass, Double
compression cable glands, Solderless crimping type copper /
aluminium sockets for Copper and aluminium cables respectively
excluding cable tray, etc, complete as directed by Engineer-In-
Charge.

a 28 3 C x 10.0 Sqmm. 125 Rmt 3500

b 45 3 C x 16.0 Sqmm. 200 Rmt 9000
c 45 3 C x 95.0 Sqmm. 375 Rmt 16875

Providing, laying, jointing, fixing, testing, painting, commissioning

GI 'B' class' pipe of approved make conforming to IS:1239 with a
minimum weight as per IS standards, including cost of GI
specials, cutting the pipes to the required lengths, threading,
jointing the pipes, chasing the walls & floors, making holes
5
necessary in walls ,RCC & floors, clamping to walls / supports
using fabricated MS brackets of approved design, GI threaded U
clamps, pipe supports & restoring the walls & floors to the original
conditions, necessary testing, refilling etc., complete all as
specified and directed by Engineer-In-Charge.

The exposed pipes shall be painted with 2 coats of approved Fire

red colour synthetic enamel paint over a coat of metal primer,
including making the necessary colour bands / marking for
differentiating the pipes as specified. The buried and concealed
pipes shall be painted with 2 coats of anticorrosive black
bitumastic paint and buried pipes to be provided with sand alround
for 150mm thickness in the trench including all necessary
excavation and back filling as per specification.

The entire piping system in part or as a whole has to be tested to

a hydraulic test pressure of 14 kg/sq.cm for a period of not less
than 24 hours. the piping shall be concealed after satisfactory
testing of the system. The contractor shall make all arrangements
for water for testing.

a 275 25mm dia 325 Rmt 89375

b 70 32 mm dia 475 Rmt 33250
c 70 40mm dia 650 Rmt 45500
d 90 50 mm dia 750 Rmt 67500
e 45 65 mm dia 950 Rmt 42750
f 70 80mm dia 1125 Rmt 78750
g 260 100mm dia 1500 Rmt 390000
h 140 150mm dia 2175 Rmt 304500

Supply, installation, testing & commissioning of C.I. Non-return

valves of approved make conforming IS:5312 (PN 16) swing
6
check type with required flanges, nuts, bolts, gaskets, etc,
complete as directed by Engineer-In-Charge.

a 3 100 mm dia 5800 Nos. 17400

b 2 150 mm dia 7500 Nos. 15000
30
 Supply, Installation, testing & commissioning of CI butterfly valves
of approved make conforming BS 5155 (PN 16) slim seal
7
standared lever operated type with required flanges, nuts, bolts,
etc, complete as directed by Engineer-In-Charge.

a 6 50 mm dia 2700 Nos. 16200

6 80 mm dia 3050 Nos. 18300
b 6 100 mm dia 3650 Nos. 21900
c 4 150mm dia 6350 Nos. 25400

Supply & installation of Pressure switches of suitable range for

8 pump sets with Ball valves, Fittings like unions / colours /
reducers, etc, complete as directed by Engineer-In-Charge.
2 3500 Set 7000

Supply & installation of Pressure gauges of suitable range for

9 pump sets with Ball valves, siphon, Fittings like unions / colours /
reducers, etc, complete as directed by Engineer-In-Charge.
2 1700 Set 3400
Supply, installation, testing & commissioning of Landing Hydrants
10
comprising of the following in the Fire duct

1 No. of Single headed hydrant valve as per IS 5290, made of SS

a with 63 mm dia instantaneous single outlets & 100 mm dia fanged
inlet ,Blank caps, chain & hand wheels etc complete.
8 6000 Nos. 48000
1 Nos. of 15 M long, 63mm dia RRL hose with instantaneous
b
couplings and Hoses shall be stored in side the hose cabinet.
8 5600 Nos. 44800
c 8 1 no. SS short branch pipe with nozzle. 2150 Nos. 17200

Providing and fixing door with frame for all internal fire hydrants
fabricated from 16 SWG Alumunim of size 750 x 1200 x2100 mm
double door including 2 nos allen key lock for locking along with
padlock arrangement & fully glazed with 4 mm thick float glass
approved by local Fire Authority, stove enameled fire red finish
d with " fire hose' written on front suitable to house 15 mm long four
length of canvas hose with couplings,one no of branch pipe, one
fire mans axe and two numbers of portable extinguishers, first aid
fire hose and supports for hoses, branch pipes, Axe and hose
reel. as per approved design including necessary fixing
arrangement for hoses & axe and branch pipe.)
4 11000 Nos. 44000

Providing & fixing Hose reel drum of swinging type with 19 mm dia
Rubber braided hose of 40 Mtr length with Shut off nozzle of jet &
e spray type, including all fixing materials and including brass ball
valve (upstream) as per specifications etc, complete as directed
by Engineer-In-Charge.
8 6300 Nos. 50400
Supply, installation & commissioning of fire brigade inlet
connection of 4 way with 4 nos. 63 mm dia. built - in Gun metal
Non- return valves instantaneous coupling type arranged on 100
mm dia. Pipe manifold and connected to wet riser main as well as
11
to Fire water tank. Quoted rate shall be included with C.I. Butterfly
valve, C.I. Non-return valve and M.S. cabinet of suitable size with
mounting supports etc, complete as directed by Engineer-In-
Charge.
1 9000 Nos. 9000

31
 Supply, installation, testing & commissioning conventional
Sprinkler quartzoid bulb type with 15mm screwed end connection
12
of 68 deg. C. temperature rating,K 80 & orifice shall not be less
than 6mm, etc, complete as directed by Engineer-In-Charge.

60 Pendent sprinkler /Side throw 400 Nos 24000

13 15 SITC of Flexible Drop for The sprinkler 750 mm in length 1100 Nos. 16500
Providing & fixing approved make 15mm dia. automatic air
14 release valve with unions etc. complete as directed by Engineer-
2 In-Charge. 1650 Nos. 3300
FIRE EXTINGUISHERS - PART-B
ABC type fire extinguisher of 6 kgs. capacity, filled in brand new
seamless cylinder with powder coated finish, made out of
15 Manganese steel, with wheel type valve, discharge nozzle, bend
& horn, wal mounting bracket etc., complete, confirming to IS:
10 13849 4000 Nos. 40000
Providing & Fixing of CO2 type Fire Extinguisher 4.5 kgs Capacity
16
10 IS: 15683 7000 Nos. 70000
Fire buckets round bottom type enamel painted, white inside &
17 Red out side and Letter "FIRE" in black out side and handle with
5 mounting bracket each 4nos. 2950 Nos. 14750
Fire bucket stand fabricated by MS angles to install 2 Nos. of
18
5 buckets. 850 Nos. 4250
SIGNAGES - PART-C
19 10 Providing & fixing Exit Light fixtures with night glow 350 Nos 3500
Signage with printed "IN CASE OF FIRE, USE STAIRS UNLESS
INSTRUCTED OTHERWISE" of 1.5cm height letters in red with
20 white back ground.The size of the board shall be 25cm x 30 cm
and shall be fixed at the height of 2 mts. from finished floor near
Manual call points.
6 300 Nos. 1800

Floor indentification signage ( ie, GROUND FLOOR …etc.) at

each stair enclosure on every floor, indicating the floor number in
21
words, lettering size shall be 7.5 cm with contrasting colour from
back ground. Size shall be 15cm x 60cm.
6 250 Nos. 1500
Liasion work with Local authority and obtaining Fire NOC
22 and all relevant applicable approvals including required
1
drawing work. 100000 Job 100000
TOTAL RS. 2203600

ENGINEERING DEPT. –EAST ZONE

Name of Work : CONSTRUCTION OF SUB ZONAL OFFICE BUILDING AT F.P. NO. 207,
T.P.S. NO. 113 (VASTRAL) IN VASTRAL WARD, EAST ZONE, AHMEDABAD
Bill of Quantities

Signature of contractor Additional City Engineer (E.Z. )

Seal Ahmedabad Municipal Corporation
Date

32
 AHMEDABAD MUNICIPAL CORPORATION
EAST ZONE

Name of Work : CONSTRUCTION OF SUB ZONAL OFFICE BUILDING AT F.P. NO. 207, T.P.S. NO. 113
(VASTRAL) IN VASTRAL WARD, EAST ZONE, AHMEDABAD

FINANCIAL BID (To Be Submitted Online Only)

Sr. No. Description Amount
1 Amount For Civil Work RS. 3,63,22,489.05
RS. 46,86,090.00
2 Amount For Electrical&CCTV Work
3 Amount For Landscaping Work RS. 56,150.00
4 Amount For Fire Detection & Fire Fighting Work RS. 22,03,600.00
Total RS.4,32,68,329.05

I/We am/are willing to carry out work at ______ % above / below (should be written in figures and words)
the estimated cost mentioned above.

Estimated cost put to tender : Rs. 4,32,68,329.05 Estimated cost put to tender : Rs. 4,32,68,329.05
Add_____% above : Rs ___________ Deduct_____% below : Rs __________
Net: Rs___________ Net : Rs__________
In words : Rupees _______________________ In words : Rupees_____________________
____________________________________ ______________________________________
______________________________________
______________________________________

Signature of contractor Additional City Engineer ( E.Z. )

Seal Ahmedabad Municipal Corporation
Date

33