Total Power: 200-350 Watts

350 Watts Input Voltage: 85-264 VAC

120-300 VDC

NTS350 Series # of Outputs: Single

Electrical Specs
Input
Input range 85-264 VAC; 120-300 VDC
Frequency 47-440 Hz
Inrush current 38 A max., cold start @ 25°C
Efficiency 85% typical at full load
EMI filter FCC Class B conducted and radiated
CISPR 22 Class B conducted and radiated
EN55022 Class B conducted and radiated
VDE 0878 PT3 Class B conducted and
radiated.
Power factor 0.99 typical
Safety ground
leakage current <0.5 mA @ 50/60 Hz, 264 VAC input

Special Features Output

Maximum power 200W convection; 350 W with 30 CFM
• Active power factor correction forced air
• IEC EN6100-3-2 compliance Adjustment range ±5%
• Remote sense Standby output 5 V @ 2A regulated, ±5%
• Power fail and remote inhibit Fan output 12 V @ 1A, -5 %, +7%, 0.5A for -CF version
• Single wire current sharing Hold-up time 20 ms @ 350 W load, 115 VAC nominal
• Built-in EMI filter line at factory voltage setting
• Low output ripple Overload protection Short circuit protection on all outputs.
• 5V standby Case overload protected @ 115-130%
• 12V fan output above peak rating
• Overvoltage protection Overvoltage protection 20% to 35% above nominal output
• Overload protection
• Thermal overload protection Logic Control
• DC power good Power failure TTL logic signal goes high 100-500 msec
• Built in OR-ing diode / FET after main output. It goes low at least 4
• Optional fan cover (-CF suffix) msec before loss of regulation
Remote on/off Requires an external contact closure to
inhibit outputs
DC OK TTL logic goes high after the output is in
Environmental regulation. It goes low when there is loss
of regulation.
Operating temperature: 0° to 50°C ambient Remote sense Compensates for 0.5 V lead drop min.
derate each output at 2.5% per degree from 50° to Will operate without remote sense
70°C connected. Reverse connection protected.
Electromagnetic susceptibility: Designed to meet
EN61000-4, -2, -4, -5, -11 Level 3
Humidity: Operating; non-condensing
10% to 90%
Vibration: Three orthogonal axes, sweep at Safety
1 oct/min, 5 min. dwell at four major resonances
2 G peak 8 Hz to 500 Hz, operational TUV 60950
Storage temperature: -40° to 85°C UL 60950
CSA 60950
Temperature coefficient: ±.04% per °C NEMKO 60950
MTBF demonstrated: >1M hours at full load and AUSTEL 60950
25°C ambient conditions CB Certificate and report
CE Mark (LVD)

1 Technical Support: (888) 41-ASTEC or (407) 241-2752

Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 rev 12.19.05
 AMERICAS EUROPE ASIA

5810 Van Allen Way Astec House, Waterfront Business Park Units 2111-2116, Level 21
Carlsbad, CA 92008 Merry Hill, Dudley Tower1, Metroplaza
Telephone: 760-930-4600 West Midlands, DY5 1LX, UK 223, Hing Fong Road
Facsimile: 760-930-0698 Telephone: 44 (1384) 842-211 Kwai Fong, New Territories
Facsimile: 44 (1384) 843-355 Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426

NTS350 Series
Ordering Information
Model Output Minimum Maximun Load with Maximum Load with Peak Regulation2 Ripple
Number Voltage Load Convection Cooling 30 CFM Forced Air Load1 P/P (PARD)3

NTS353 12V 0A 16.6 A 29.2 A 33 A ±2% 120 mV

NTS358 48V 0A 4.2A 7.3A 8.2 ±2% 480mV
NTS359 54V 0A 3.7A 6.5A 7.4 ±2% 540mV

1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges.

Pin Assignments
Connector
SK1 PIN 1 Line
PIN 3 Neutral
PIN 5 Ground

SK5 PIN 1 V1 swp

1 5 + V OR-ing out
PIN 2 - Remote Sense
PIN 3 + Remote Sense + V out
6 10 PIN 4 5VSB (standby)
PIN 5 5VSB return Common
PIN 6 +12V
135

5 10
PIN 7 Common SK1
PIN 8 Inhibit
PIN 9 DC power good (DC OK) 1 6

PIN 10 Power Fail (POK)

-CF option
Adjustment Potentiometers (SEE NOTE 5) P1 P1
P1 +V1 Output adjust Voltage P3
P3 +5VSB adjust ADJ POT
Mating Connectors 1.27 (32.26) -CF option
SK1 AC input Molex 09-50-8051 (USA)
Molex 09-91-0500 (UK)
PINS:08-58-0111 1.14 (29.1) a b .75 (19.1) (3X)

b 1.5 (38.10)
SK2,3,4 Molex BB-124-08
a

SK5 Control signals Molex 90142-0010 6.4 (2X) 5.85 (148.7)

PINS: 90119-2110 or 6.25 (158.7)
Amp: 87977-3
PINS: 87309-8

Astec Connector Kit #70-841-022 includes

all of the above

Notes: b a a b
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±.02”.
3. Specifications are at factory settings 2.5 (63.5) (4X) 4.0 (101.6)

4. Mounting maximum insertion depth is 0.12”.

5. Warranty: 1 year
6. Weight: 2.5 lb. / 1.13 kg.
b a a b

4.7 (119.6) (2X) #6-32 (8 places)

5.5 (139.7) (2X) M3 (8 places)
7.0 (177.8)

www.astecpower.com 2