Angle Seat Motor Valve 7210

1/4“ up to 2“

Motor valve for on/off- and modulating operation for neutral

and aggressive media.
• Compact design
• Self calibration
• Unaffected by lightly contaminated media
• For temperatures from -58°F up to +428°F
• Working pressure up to 580 psi
• Versatile actuator options
• Actuators with control function also available with safety position

Technical Information Valve

Body material DN15-50: Bronze Stainless steel CF8M
DN65-80: Brass
Nominal size 1/2“ up to 2“ 1/4“ up to 2“
Connections:
Pipe threads acc. ISO 228-1 1/2“ - 3“ 1/4“ - 3“
NPT thread 1/2“ - 3“ 1/4“ - 3“
Welding ends - 1/2“ - 3“
Clamp connections 1/2“ - 3“
Nominal pressure 230 psi 580 psi
Max. fluid temperature -22°F up to 392°F, opt. -58°F up to +428°F
Viscosity max. 600 mm²/s (600 cSt)
Vacuum max. 0.0295 mercury (Hg)
Operating pressure max. 175 psi
packing underneath
Working pressure for Tri-Clamp con- maximum 235 psi
nection

Position electronics
Actuator 180 lbf
(self adapting)

Coupling

Packing from
filled PTFE, self
Head section adjusting
Valve stem Seating seal PTFE
1.4571, roller or alternative
burnished materials
Control plug

Schubert & Salzer Inc., 4601 Corporate Drive N.W., Suite 100 Concord, NC 28027, Ph.: (704) 789 0169, Fax: (704) 792 9783
info@schubertsalzerinc.com, www.schubertsalzerinc.com
Angle Seat Motor Valve 7210

Technical Information CA-Actuator

Function Control On/Off
Motor type CA24C CA260C CA24C-R CA260C-R CA24 CA260
Mains connection 24V AC/DC 90-260V AC 24V AC/DC 90-260V AC 24V AC/DC 90-260V AC
Set point range (0)2-10V / (0)4-20mA* 3-term**
Feedback (0)2-10V / (0)4-20mA optional
Limit switch 2 optional
Potentiometer feedback - optional
Max. switching capacity 24V AC/DC 200 mA 250V AC/DC 1A
38.1 / 50.8 / 76.2 s/inch 50.8 or 76.2 s/inch
Actuating speed
(Standard: 50.8 s/inch) (Standard: 76.2 s/inch)
Monitoring of tensile force, set point, temperature of the elect-
Safety functions Tensile force monitoring
ronics, etc.
Diagnostic functions Storage of motor and total operating time, temperature and
-
directional classes, etc.
Fail Safe position - - freely adjustable -
Load 500 Ω for current set point / 95 kΩ for voltage set point -
Max. input 13 W 12 W 13 W 12 W 13 W 12 W
Input heating resistor 10 W
Starting current heating resistor 6A 2,5 A 6A 2,5 A 6A 2,5 A
Actuating power 180 lbf
Protection class (EN 60529) IP 65
Adm. Ambient temperature 14°F to +140°F
Duty cycle 100%
*: for control with volt-signal split range adjustments are possible
**: minimum switch on time 200ms
Wiring diagrams of the actuators can be found in the manual.
Angle Seat Motor Valve 7210

Pressure Capability
Inlet pressure psi
Nominal size 1/4“ 1/2“ 3/4“ 1“ 1 1/4“
On/off Control On/off Control On/off Control On/off Control On/off Control
Stainless steel
- 250 580 250 290 250 175 175 100 100
body
Bronze body - - 230 - 230 - 175 - 100 -
Body stainless
steel pressure - - - - - - - - 580 247
balanced

Inlet pressure psi

Nominal size 1 1/2“ 2“ 2 1/2“ 3“
On/off Control On/off Control On/off Control On/off Control
Stainless steel
70 70 40 40 - - - -
body
Bronze body 70 - 40 - - - - -
Body stainless
steel pressure 365 250 365 250 250 250 205 205
balanced

Cv-Values
Characteristic linear equal percentage
1 1 2 1 1 2
Size 1/4“ 1/2“ 3/4“ 1“ 2“ 3“ 1/4“ 1/2“ 3/4“ 1“ 2“ 3“
1/4“ 1/2“ 1/2“ 1/4“ 1/2“ 1/2“
100 % 0.7 4.4 10.2 16.2 23.2 31.3 42.9 60.3 80 0.7 3.5 7 11.6 18.6 29 34.8 44.1 53.4
40 % 0.3 1.7 4.1 6.7 9.3 12.8 - - 1.4 2.8 4.6 7 11.6 - - -
25 % 0.2 1.1 2.6 4.2 - - - - 0.9 1.7 3 - - - - -
15% - - - - - - - - 0.5 - - - - - - -
10% - 0.5 - - - - - - - - - - - - - -
7,5% - - - - - - - - 0.3 - - - - - - -

On-Off 1.1 4.4 10.4 19.7 32.5 40.6 52.2 71.9 98.6
Angle Seat Motor Valve 7210

Article number
Ordering Number System 7210/ K S
Nominal size:
1/4“ (DN 8) only with seating seal PEEK 008
1/2“ (DN 15) 015
3/4“ (DN 20) 020
1“ (DN 25) 025
1 1/4“ (DN 32) 032
1 1/2“ (DN 40) 040
2“ (DN 50) 050
2 1/2“ (DN 65) 065
3“ (DN 80) 080
Item:
Valve V
Valve without actuator U
Actuator A
Body design:
Angle bodied 1
Connection:
Whitworth-thread 0
NPT thread 5
without thread 6
Welding ends acc. ISO H
Welded ends acc. DIN 11850-series 2 - drawing R0112 D
Welding ends acc. ISO, drawing R0094 E
Tri-clamp Z
Body material:
Bronze 1
Stainless steel 2
Seating seal:
PTFE 0
PEEK 7
Actuator:
Control actuator CA24C, 24V AC/DC, with pos. electronic, stanard adjustm.: control sig. 4-20mA, feedback 4-20mA, 2 C
limit switch
Control Actuator CA260C, 90-260V 50/60Hz, with pos. electronic, Standard adjustm. 4-20mA, feedb. 4-20mA, 2 limit D
switch
On-Of (3-point) actuator CA24, 24V AC/DC E
On-Off (3-point) actuator CA260, 90-260V, 50/60Hz F
Control plug:
none -
linear 100% 1
equal percentage 100% 2
linear 40% 3
equal percentage 40% 4
linear 25% 5
equal percentage 25% 6
Special versions
See following positions S
Pressure balanced version P
Lower part and console of the actuator KTL-coated K
Safety position:
without safety position -
Fail-Safe: normally closed at power failure 2
Fail-Safe: normaly open at power failure 3
Stroking times
Standard (51 s/inch for control actuators - 76 s/inch for on-off-actuators) -
76 s/inch 4
38 s/inch 5
51 s/inch (On/Off Actuator Type 2032) 9

Ordering example: 7210/025VK1520C1

Angle seat motor valve type 7210, 1“, pipe thread NPT, stainless steel body, seating seal
PTFE, control actuator CA24C, 24V AC/DC, 180 lbf, control electronics 4-20 mA, position
feedback 2-10V, linear characteristic, Cv-value 16.2 (100 %).
Angle Seat Motor Valve 7210
Dimenstions and Weights CA-actuators

Body with threaded ends Rp/NPT

Body with welding ends DIN/ISO

Size A C ISO Size B L E F E F SW1 SW2 Stroke Weight

pressure lbs
d1 d1
G / NPT G NPT s s G / NPT DIN/ISO balanced
1/4“ 1/4“ 0.47 0.42 - - - - 2.36 - 10.16 12.05 - - 0.79 1.18 0.33 5
1/2“ 1/2“ 0.59 0.57 0.84 0.08 0.71 0.06 2.56 3.15 10.35 12.2 - - 0.98 1.18 0,35 5.5
3/4“ 3/4“ 0.64 0.59 1.06 0.09 0.87 0.06 2.95 3.54 10.63 12.2 - - 1.22 1.18 0,55 5.5
1“ 1“ 0.75 0.71 1.33 0.1 1.1 0.06 3.54 3.94 10.83 12.36 11.57 13.27 1.54 1.18 0,71 6
1 1/4“ 1 1/4“ 0.84 0.73 1.67 0.1 1.34 0.06 4.33 4.33 11.46 12.99 12.01 13.62 1.89 1.18 0,83 7
1 1/2“ 1 1/2“ 0.84 0.73 1.9 0.1 1.57 0.06 4.72 4.72 11.61 13.15 12.28 13.94 2.17 1.18 0,87 7.5
2“ 2“ 1.01 0.75 2.37 0.11 2.05 0.06 5.91 5.91 12.24 13.43 12.99 14.33 2.68 1.26 0,87 9
2 1/2“ 2“ 1.19 1 3 0.11 2.76 0.08 8.43 7.09 - - 13.9 14.09 3.94 1.61 0,87 13.5
3“ 2“ 1.31 1.08 - - - - 8.43 - - - 16.81 15.24 3.94 1.61 0,87 18
Other body designs on request Dimensions in inch
Text and pictures are not binding. We reserve the right, to alter the equipment.
7210 - data sheet - US/Version: 23.09.2020