Unijunction Transistor (UJT) : Amarendra Narayan

Unijunction Transistor (UJT)
Amarendra Narayan
A Unijunction Transistor (UJT) is a three terminal semiconductor switching device. It consists
of a bar of n-type silicon material with a terminal attached at its two ends known as base 1 and base
2. A third terminal is connected with a heavily doped p-type material alloyed into the bar part way
along its length, and is known as the emitter. Since there is only one rectifying junction within the
device, it is called a ‘Unijunction’ transistor. The unijunction transistor exhibits negative resistance in
its characteristics. If finds use in relaxation oscillators in variety of applications.
Construction of Unijunction Transistor (UJT)
A Unijunction Transistor is constructed by forming a pn-
Junction between a lightly doped N type silicon bar and a heavily
doped P type material on one side as shown in the figure. The ohmic
contact on either ends of the silicon bar is termed as Base 1 (B 1) and
Base 2 (B2) and P-type terminal is named as emitter.
The emitter junction is placed such that it is closer to Base 1
than to Base 2.The symbol of UJT is similar to that of JFET except that
the emitter arrowhead for UJT is bent in the direction in which
conventional current flows.
How does a Unijunction Transistor (UJT) work
The simplified equivalent circuit (at Figure 3 below)
shows that N-type channel consists of two resistors RB2 and RB1
in series with an equivalent diode, D representing the PN
junction. The emitter PN junction is fixed along the ohmic
channel during its manufacturing process.
The variable resistance RB2 is provided between the
terminals Emitter (E) and Base 2 (B 1), the RB1 between the
terminals Emitter (E) and Base 1 (B 1). Since the PN junction is
closer to B1, the value of RB1 will be less than the variable
resistance RB2.
A voltage divider network is formed by the series
combination of resistances RB2 and RB1. When a voltage is applied across the semiconductor device,
the potential will be in proportion to the position of base points along the channel.
The Emitter (E) acts as input when employed in a circuit, as the terminal B 2 is grounded. The
terminal B1 is positively biased with respect to B 2 when a voltage (VBB) applied across the terminals B1
and B2. When the emitter input is zero, the voltage across resistance RB2 of the voltage divider circuit
is calculated by
RB2
V RB 2= V
R B 1+ R B 2 BB
The ‘intrinsic stand-off ratio’ (η) of the Unijunction Transistor is defined applied as the ratio
of RB2 to RBB. Most UJT’s have η value ranging from 0.5 to 0.8. The PN junction is reverse biased if the
voltage applied at the emitter is less than the sum of voltage developed across resistance R B2 (ηVBB)
and the voltage drop across a forward biased PN junction, V f. i.e. V E < ηV BB +V f A very high
impedance is developed in this situation prompting device to move into non-conducting state i.e., it
will be switched off and no current flows through it. The UJT begins to conduct when the PN
junction is forward biased. This is achieved when voltage applied to the emitter terminal,
V E > V RB 1 +V f , i.e. V E > ηV BB +V f . This results in larger flow of emitter current from emitter
region to base region. Increase in emitter current results in injection of large number of conduction
electrons in the region between emitter and Base 2. This reduces the resistance between emitter and
Base 2, resulting in a reduction in total resistance between Base 1 and base 2. As a result a large
current flows between base 1 and base 2.
The Unijunction Transistor (UJT) will act as voltage breakdown device, when the input applied
between emitter and base 1 reduces below breakdown value i.e., R B1 increases to a higher value. This
shows that RB1 depends on the emitter current and it is variable.
Characteristics Curve of Unijunction Transistor (UJT)
The characteristics of Unijunction Transistor (UJT) is given below. The figure shows Emitter current IE
on the x-axis and VE on the y-axis. The curve has three regions: (1) Cutoff region (2) Negative
Resistance region, (3) Saturation region.
Fig. 4 – Characteristics of Unijunction Transistor (UJT)

Cutoff region
Cutoff region is the area where the Unijunction Transistor (UJT) doesn’t get sufficient voltage to turn
on. The applied voltage VE hasn’t reached the triggering point, thus making transistor to remain in off
state.
Negative Resistance region
When the emitter reaches the triggering voltage, VTRIG, Unijunction Transistor (UJT) will turn on.
After a certain time, if the voltage applied to the emitter lead increases, it will reach out at V PEAK. The
voltage drops from VPEAK to Valley Point even though the current increases (negative resistance).
Saturation
Saturation region is the part of characteristic curve in which the current and voltage both
increase, if the applied voltage to emitter terminal increases.
Applications of Unijunction Transistor (UJT)

The Unijunction Transistor can be employed in variety of applications such as:
•Switching Device
•Triggering Device for Triacs and SCR’s
•Timing Circuits
•For phase control
•In sawtooth generators
•In simple relaxation oscillators
Application of Unijunction Transistor (UJT) in Relaxation Oscillator
UJT Relaxation Oscillator can be practically viewed by the following circuit.
Use of Unijunction Transistor (UJT) in Relaxation Oscillator
A relaxation oscillator is circuit that generates a sawtooth waveform. A typical circuit is shown above.
The capacitor C1 is charged through the resistor R 3 until VE reaches the peak point. (The UJT’s emitter
terminal has no effect on C1 until peak point is reached). When the emitter voltage reaches peak
voltage point, the emitter-base 1 resistance diminishes which results in rapid discharge of the
capacitor C1. The capacitor C1 discharges until VE goes below the valley point. The emitter-base 1
resistance will then return back to high resistance state, thus completing the cycle. The capacitor C 1 is
nowfree to charge again.
Application of Unijunction Transistor (UJT) in Speed Control Circuit
Speed Control Circuit is one of the typical applications of UJT to produce set of pulses to trigger and
control Thyristor. We can adjust the speed of universal motors by using UJT as triggering circuit in
combination with SCR and Triacs.
Advantages of Unijunction Transistor (UJT)
The advantages of Unijunction Transistor include:
• low cost
• negative resistance characteristics
• Requires low value of triggering current
• A stable triggering voltage
• Low power absorbing device
Disadvantage of Unijunction Transistor (UJT)
The main disadvantage of Unijunction Transistor is its inability to provide appropriate amplification.
Further reading: https://electricalfundablog.com/unijunction-transistor-ujt-construction-working-

characteristics-curve-applications/
Also see https://electricalfundablog.com/thyristor-working-vi-characteristics/
https://www.elprocus.com/introduction-to-uni-junction-transistor-construction-and-operation/

Unijunction Transistor (UJT) : Amarendra Narayan

Uploaded by

Copyright:

Available Formats

Unijunction Transistor (UJT) : Amarendra Narayan

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Unijunction Transistor (UJT) : Amarendra Narayan

Uploaded by

Copyright:

Available Formats

Unijunction Transistor (UJT)

Fig. 4 – Characteristics of Unijunction Transistor (UJT)

Applications of Unijunction Transistor (UJT)

Further reading: https://electricalfundablog.com/unijunction-transistor-ujt-construction-working-

You might also like