Di750 - All Active Solutions: June 2009
Di750 - All Active Solutions: June 2009
Di750 - All Active Solutions: June 2009
Legal Notice
This document is designed as a diagnostic tool, primarily for Konica Minolta's support personnel, and authorized
service representatives. Konica Minolta recommends that all service be performed by an authorized service
representative. Users are responsible for seeking advice of a Konica Minolta authorized service representative
regarding the information, opinion, advice or content of this document.
USER AGREES THAT USE OF THIS DOCUMENT IS AT USER'S SOLE RISK AND THAT THIS DOCUMENT IS PROVIDED
ON AN AS IS BASIS WITHOUT WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, WARRANTIES OF TITLE OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, OTHER THAN THOSE WARRANTIES THAT ARE IMPLIED BY LAW AND INCAPABLE OF
EXCLUSION. IN NO EVENT WILL KONICA MINOLTA OR THOSE ACTING ON ITS BEHALF BE LIABLE FOR ANY
DAMAGES, INCLUDING, WITHOUT LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
PUNITIVE DAMAGES ARISING OUT OF YOUR USE OF THIS DOCUMENT.
Description
Gray bands or blur lines from front-to-rear on the trail edge of 11x17 prints/copies.
Solution
PROBABLE CAUSES:
1. Worn fixing unit lower roller bearings or flat spots on the lower roller is allowing the lower roller to bounce which causes bands during image transfer.
Replace the lower fixing roller and bearings (p/n 55VA-5281).
2. Burrs on fixing drive gear/E (p/n 55VA-1670) causing inconsistent fixing unit rotation.
Replace fixing drive gear/E.
4. The cleaner shaft holders (bearings) for the toner guide brush are seized resulting in improper brush rotation and a loss of ground to the brush.
Replace the shaft holders front and rear (p/n 55VA75020) and ensure there is a clean path to ground.
5. Binding bushings in the resist (registration) unit or flat spots on the resist unit rollers causing transfer blur due to improper paper speed.
Remove and clean all resist unit bushings and replace worn parts as needed.
6. Worn components or a build up of foreign material in the main drive or drum drive units. Clean or replace affected parts.
Description
Dark band from front-to-rear, normally on the first print of a run.
Solution
CAUSE: The cleaner shaft holders (bearings) for the toner guide brush are seized resulting in improper brush rotation and a loss of ground to the brush.
SOLUTION: Replace the shaft holders front and rear (p/n 55VA 7502 0) and ensure there is a clean path to ground.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
2
Di750 Image failure other than density/color - magnification, blur
Solution ID TAUS0638932EN* Solution Usage 0
Description
Recurring copy quality issues, such as poor image density, overall light image quality, and blurred image. In addition, developer and toner intermittently dump
at the magnet roller.
Solution
PROBABLE CAUSES:
1. When developer and OPC drum was replaced, thecounts were not reset.
Reset the Developer and Drum counters back to "0" counts. This is done in the 25Service mode:
a. Select (5 - Parts counter) =>select (1 - Count of special parts).
b. Use the "up" and "down" keys to select the appropriate part name to reset.
c.Use the "counter reset" key to clear the count. If a problem is encountered when resetting the count, please refer to the Service manual for more details.
d.Ifdetermined that the drum count had not been reset, then reset the counter back to "0" counts, especiallyif the drum is less than half of its recommended
yield or if it is new. For example, if thedrum yield is rated at 750K copies, the drum counter can be reset up to 375K copies for that particular model. If a drum
count is set to "0" after or near 375K copies, image stabilization control may be unable to maintain a good copy quality. Replace any drum if it is determined
that the counter was never reset and the amount of prints exceeds half of the drum recommended yield.
e.Ifdetermined that the developer count was not reset, the developer should be replaced and the developer count returned to "0". The developer counter
cannot be reset to "0" without replacing the developer.
f.After resetting the counters, follow the procedures outlined in the Service manual for adjusting the high voltage and drum peculiarity adjustments of the
MFP. A table outlining a list of adjustment items and order to perform adjustments is provided at the beginning pages of the Adjustment section of the Service
manual.
2. Improperly set developer cover. An improperly set developer cover allows too much air to circulate around the developer chamber. This excess air will
affect the tribo-electrification process (agitation of developer to build a charge). Also, the extra air flow in the developer chamber increases the possibility of
contaminants and humidity to enter the developer chamber degrading the developer's ability to hold a charge.
Make sure the developer cover is properly positioned. The developer covers have a cylindrical shaped post on the front and rear sides of the cover. These
posts slide into a groove in the developer assembly. Make sure that both the front and rear posts of the developer covers are properly positioned in the
corresponding slot in the developer unit before locking the cover in place. Check to see that the developer locking tabs are securely fastened. If the developer
cover does not stay firmly in place the cover may need to be replaced.
3. Improper position of the charge andT/S coronas. It is possible that due to wear of the corona cleaners or due to the improper installation of the corona
wires, the height of the corona wire may be incorrect. Also, incorrect corona springs and corona wires can cause the wires to be too taut, too slack, have a
different thickness or even be composed of a different material. This causes the charge applied to the drum to be incorrect. Varied image
stabilization will result.
Always make sure the proper corona wires are being used along with the proper tensioning springs. Verify that the corona cleaners are intact and free from
wear. Replace if necessary. Also make sure that the corona wires are positioned properly. Use the Service manual as a reference for replacing the wires.
4. Improperly set drum flange. An improperly set drum flange can cause image stabilization issues. This is due to the lack of proper drum grounding
maintained by the drum flange.
Make sure that the drum flange is properly set. Refer to the diagram .
5. Error messages received during Auto maximum density adjustment or Auto dot diameter adjustments. Error messages 1, 2 and 3 can be given when
performing the automatic adjustments after replacement of developer or drum. Usually if the codes are ignored theMFP will function without indicating a
service code when theMFP is returned to a normal copy mode. If the codes are generated during the performing of the automatic adjustments, image
stabilization will not be performed properly unless the code is cleared and the adjustment mode repeated.
Usually the indication of error code 1, 2 and 3 indicates a problem with the drum potential senor or the TCB (Toner Control Board). If properly connected and
code fails to clear, replace the sensor. Refer to the adjustment section of the Service manual for the details of each of these error codes. Reference to these
codes is located at the end of the adjustment procedure.
6. Developing unit was disassembled during developer change. Magnet roller angle has been altered and also the developer gap is no longer accurate.
The developing unit should never be disassembled, only tilted at an angle and emptied by turning the developer drive gears.
CAUTION : Do not adjust the gap unless it is absolutely necessary. Remember, once the gap has been altered, the developing unit will need to be replaced.
The developer gap information should only be used to determine if the doctor blade had been altered. Adjust only as a temporary and last resort to repair copy
quality and dumping issue due to incorrect adjustment. Replace the developing unit on your next service visit.
Note : Please see Service & Support Bulletin 4267 for additional details. To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
3
Di750 Image voids or deletions
Solution ID TAUS0643221EN* Solution Usage 2
Description
Approximately 3mm to 4mm all around the image is being cut off when scanning to FTP. The originals are 8.5x11 and have image at the edge of the page.
Even when selecting reduction, the image is still being cut off.
Solution
CAUSE: All scanning through the EDH or platen is subject to edge erase. All four sides of the scanned image are erased approximately 2mm to 4mm all
around the entire document. This is done to prevent the edge of the originals from scanning which will produce a shadow/line when imaged. This is the default
function when a document is scanned.
SOLUTION: To remedy this issue make the following selections in the Scan to FTP mode:
1. Under "Function" select the "Application" key.
2. Under "Application" select All-Image Area.
3. Press the [Start] button.
The entire image should be reproduced with these settings.
Note : These settings must be selected each time a job is scanned. The All-Image Area setting can not be made as a default setting. This setting works in
all three scan modes: scan to HDD, FTP, and E-Mail.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
4
Di750 Miscellaneous
Solution ID TAUS0700453EN* Solution Usage 739
Description
NVRAM Troubleshooting Procedure used to identify NVRAM problems and and information concerning damaged or missing NVRAM/BRU.
Solution
bizhub C250/C252/C300/C350/C351/C450
NVRAM trouble codes (C-D3xx codes) can occur at any time. Mostly these codes happen when updating firmware. A NVRAM Data Restore procedure was
announced a few months ago to address these codes:
Stop, 0, 7, 1, 3, 9, *
What this procedure does is take a good image of the NVRAM off the MFP board (created when you performed the NVRAM Data Backup) and restore it to
the NVRAM. There are approximately 30 registers that can be corrupt, so the above procedure may have to be done as much as 30 times.
WARNING : If a corrupt NVRAM is suspected, DO NOT perform the NVRAM Data Backup. This will take the corrupt NVRAM image and back it up to the
MFP board. If this is done, and the NVRAM is replaced, the corrupt data that was just backed up will be transferred to the new NVRAM. If this is the case,
then the NVRAM and MFP board will have to be replaced as a set.
If a corrupt NVRAM is suspected, please try performing a Data Clear. This can be found in the Tech Rep mode.
CAUTION : All programmed addresses will be cleared. Please backup the address data using PageScope Web Connection to backup the data before
performing the Data Clear. If NVRAM replacement is necessary please be aware that the meters may not be transferred and they might be reset to zero. This
is unrecoverable and the correct meters cannot be input.
8020/CF2002/8031/CF3102
Codes C-3C00 through C-3C40 indicate a corrupt BRU.
Codes C-3C50 through C-3C90 indicates a problem with the PWB-C board or the scanner to main body cable.
bizhub 200/250/350
Common symptoms when NVRAM replacement may be necessary:
1. Machine not going to ready state.
2. Not printing to a host name with DHCP.
3. Not scanning to E-mail.
4. On startup, abort code 0x0000999a .
5. Abort code 0x00f00b00 .
6. Not printing.
7. Machine rebooting every few minutes.
8. Screen freezing in Konica Minolta logo.
9. Keep losing machine settings when power OFF.
bizhub 420/500
Common symptoms when NVRAM replacement may be necessary:
Note : First try to flash the machine to the latest firmware before swapping the NVRAM because the firmware fixes many of the following symptoms:
1. Screen freeze in Konica Minolta logo.
2. Fax unit locking up theMFP or not recognized.
3. C-E084 error code.
4. Cannot PING the MFP.
5. C-D203 error code.
6. Display resetting to Japanese.
7. Losing network settings after firmware upgrade.
8. C-E002 error code.
9. Scan to E-mail or FTP.
10. Loss of adjustment data.
11. Total counter is reset.
12. Display TCR adjustment.
13. C-284x error code.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
5
Di750 Miscellaneous
bizhub 600/750
Common symptoms when NVRAM replacement may be necessary:
1. Screen freeze in Konica Minolta logo.
2. Cannot recognize document feeder.
3. Error code SC2203 .
7145/7255
Common symptoms when NVRAM replacement may be necessary:
1. Blank screen.
2. Loss of E-mail addresses.
3. Loss of settings.
4. Error code E56-01 .
Ordering Procedures
Call the SSD Hotline at 800-825-5664, to open a Problem Ticket.
IMPORTANT : All requests for NVRAMs must be approved by the SSD Hotline and a problem ticket generated.If a request is received without an
established problem ticket number the request will be denied.
The NVRAM can be ordered via the Online Technical & Special Program order form located within MyKonicaMinolta.com:
1. Login to MKM.com.
2. Select the Service tab.
3. Select Warranty, Repair, & Special Programs (menu at left side of screen).
4. Click on Warranty Services & Technical/FOC Programs (in center of screen).
5. Select NVRAM/BRU Replacement Program.
Updates/Status
Call Logistics at 201-934-5339.
Notes :
a. Refer to the attached RA formand Bulletin Number 5783 for more detail.The bulletin may be a bit out-of-date concerning actual ordering procedures and
applicable models.
b. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Clinton Marquardt, ESS/SSD and Cesar Jimenez and Ed Bellone, Production Print/SSD
Description
What Konica Minolta printer drivers will come bundled with Microsoft® Windows Vista™ and what is the release schedule for Vista™-compatible drivers?
Solution
Please refer to the Windows Vista™ Hardware Compatibility List for Printers & Scanners.
For EFI legacy products that will not receive a Vista™-specific driver, refer to the following statement:
"The previous drivers ( System 5/5e-8/8e ) will not work on 64-bit Vista™. However, these drivers will work on the 32-bit version of Windows Vista™ with
minor issues."
Known issue : Borders and frames around icons and panes within the driver UI may not show up correctly.
Notes :
1. If a previous driver was Microsoft® Windows XP WHQL certified, Microsoft® also honors the digital signature (CAT file) on Windows Vista™.
2. The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the KMBS public site
(http://www.kmbs.konicaminolta.us) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
3. The Windows Vista™ Compatibility Legend can be viewed at: http://kmbs.konicaminolta.us/content/support/vistasupport.html
4. Refer to the attached document for a list of Konica Minolta printer drivers that come bundled with Microsoft® Windows Vista™. To view the PDF, Adobe
Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Bill Ehmke, ESS/SSD and Jim Behrends, Production Print/SSD
Description
NVRAM/BRU replacement form.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
6
Di750 Miscellaneous
Solution
The online NVRAM/BRU Replacement RA/Claim formis referencedin attached Bulletin Number 5783.
Notes :
1. AN SSD TICKET NUMBER MUST BE ASSIGNED IN ORDER TO PLACEA NVRAM/BRU ORDER ONLINE. All requests for NVRAMs must be approved
by the SSD Hotline and a problem ticket generated. If a request is received without an established problem ticket number, the request will be denied.
2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD
Description
Paper Test requirements.
Solution
For initial test the dealer/branch must supply 1000 sheets of the media paper. Once the paper is received the ticket is transferred to ESS.
If the initial test does not have any issues then a second test can be done. The dealer/branch must supply enough media to cover 1/3 of a PM cycle. There is
a charge involved to cover labor and supplies. The dealer/branch will be notified byESS before the test to communicate the charges.
SPECIAL NOTE : Solution contribution by Cesar Jimenez and Ian Lynch, Production Print/SSD
Description
How to copy/print onto envelopes.
Solution
Konica Minolta does not recommend copying/printing onto envelopes, asthe MFPwas not designed to run envelopes. Additionally, envelopes do not meet the
standards set for paper specifications. Their multi-layer make-up, adhesive, and odd size make it unreliable and potently damaging to the MFP.
The following special paper is recommended:
Transparency film
Labels
Hole punch
Rag content
Note : These special papers must only be fed from the multi-sheet bypass tray.
Description
ISW error codes list.
Solution
ISWERROR CODES
Error Code
Description
Action
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
7
Di750 Miscellaneous
01
Program is not executing normally. Restart from power ON and re-execute the ISW.
1F
Program is not executing normally. Restart from power ON and re-execute the ISW.
41
42
43
81
Check that the communication cable between input devices (PC or ISW Tool) is properly connected.
C1
There is an error in the flash ROM on the image control board. Restart from ISW. If the error persists, the life of the image control board flash ROM may
have expired. Replace the image control board.
C2
There is an error in the flash ROM on the image control board. Restart from ISW. If the error persists, the life of the image control board flash ROM may
have expired. Replace the image control board.
Error Code
Description
Action
C3
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
8
Di750 Miscellaneous
The checksum result after program writing does not match the ROM checksum data of the ISW transfer data file. Restart from ISW. If the error persists, the
ISW transfer data file may not be created correctly.
C4
An error was detected in the ISW board targeted at that time. Check the ISW board.
E1
Failed to erase flash ROM. (during ISW to printer control board and FNS control board)
There is an error in the flash ROM on the printer control board or FNS control board. Restart from ISW. If the error persists, the life of the targeted flash ROM
may have expired. Replace the targeted control board.
E2
Failed to write flash ROM. (during ISW to printer control board and FNS control board)
There is an error in the flash ROM on the printer control board or FNS control board. Restart from ISW. If the error persists, the life of the targeted flash ROM
may have expired. Replace the targeted control board.
E3
Communication error between image control board, printer control board, and FNS control board (during ISW to printer control board and FNS control board)
Check the I/F between the image control board and printer control board, or I/F between the printer control board and FNS control board.
Error Code
Description
Action
F80-11
F80-21
F80-30
ISW time-out
F80-31
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
9
Di750 Miscellaneous
Perform ISW data install
F80-32
F80-40
F80-41
Description
Support for Account track, Secure print, and User authentication from Unix/Linux environments.
Solution
Konica Minolta does not support Account track, Secure print, and User authentication from Unix/Linux environments at this time.
The availability of these options for Unix/Linux environments is being considered for future development.
Please attachticket to this solution and provide the following information;
1. Product model number(s).
2. Now many products placed or being considered for placement.
3.What "flavor" and version of Unix/Linux operating system.
SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD
Description
How to disable auto T/S corona electrode cleaning.
Solution
To disable auto transfer/separation electrode cleaning, perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
3. Touch [1. Software switch setting] on the touchscreen.
4. Scroll to software switch 2-4 or 3-4using the arrow keys.
5. Set 2-4 to 1 (OFF) for the 7055/7065. Set 3-4 to 1 (OFF) for the 7075/7085/Force75/Force85, 7155/7165/7255/7272/Force65, Di551/Di650, Di750/Di850
and Di5510/Di7210.
6. Power the copier OFF/ON to exit the 25 mode.
SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD
Description
How to disable auto charge electrode cleaning.
Solution
To disable auto charge electrode cleaning, perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
3. Touch [1. Software switch setting] on the touchscreen.
4. Scroll to software switch 2-3 using the arrow keys.
5. Set 2-3 to 1 (OFF) for the 7055/7065.Set 3-3 to 1 (OFF) for the 7075/7085/Force75/Force85, 7155/7165/7255/7272/Force65, Di551/Di650, Di750/Di850
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
10
Di750 Miscellaneous
and Di5510/Di7210.
6. Power the copier OFF/ON to exit the 25 mode.
Description
How to clear a fuser service code (SC 34-xx, SC 35-xx, SC 36-xx).
Solution
Using the 25 mode, softswitch 3, bit 1 must be changed back to 0 (off). To do this, perform the following steps:
1. Access the 25 mode (hold down the 2 and 5 keys at power up) or turn the main switch ON and wait for the Ready to Copy message. Hold the Utility button
down until the message "Enter 4-digit Password To Change" is displayed. (CF-5001 uses the P key instead of a Utility key).
Note : The button must be held down for about 5 seconds before the message is displayed.
2. Enter the password 9272 and press the Start (Print) button.
3. Press [1: Software SW setting] on the touchscreen.
4. Press the left up-arrow, which is displayed on the touchscreen, twice. The number displayed above the up-arrow will change to 03.
5. Select the bit number of switch 1, using the right up-arrow. 03-1 will be displayed.
6. Press the [OFF (0)] key, which is displayed on the touchscreen.
7. Power the machine OFF/ON to exit the 25 mode or press RETURN, MODE CHANGE and then BASIC SCREEN to return to normal operation.
Note : Please see the Service Manual for details.
Description
How to put the document feeder (EDH. RADF) into test mode.
Solution
The 47 mode can be used to check the sensors and motors. Code 060 has several tests for the document feeders:
DF-313
DF-316
DF-317
DF-322
EDH-2
EDH-4
EDH-5
EDH-7
Note : Please see the attached Field Service Manual pagesfor details. To view the separate manual pages Adobe Reader® must be installed. Adobe
Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Toaccess thefile(s), WinZip® must be installed. WinZip® can be downloaded from the WinZip® website at http://www.winzip.com/ddchomea.htm .
Description
Are Citrix© certified drivers available?
Solution
Citrix© certified drivers are not available.
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Description
How to install a printer using LPR (IP Printing) under Macintosh® OS9.
Solution
Please perform the procedures mentioned in the attached document.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
11
Di750 Miscellaneous
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Description
Printing to a printer on a Microsoft® Windows XP PC from a Macintosh® OS version 10.3.
Solution
Please perfrom the step-by-step procedures mentioned in the attached PDF.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez and Mark D'Attilio, Production Print/SSD
Description
IsMagneCote® paper or magnetic backed paper supported?
Solution
MagneCote® paperor magnetic backed paper is not supported.
SPECIAL NOTE : Solution contribution by Marge McLea, ProductionCustomer Support/SSD
Description
Parts have changed for the drum separating claw and toner guide brush assembly.
Solution
To be able to use the parts in common between all the listed MFPs,the drum separating claw(p/n 57GA2919) amount of coating has changed and the length
of the bristles on the toner guide brush assembly (p/n 57GA-574) has changed. See attached Parts Modification document for details.To view the PDF, Adobe
Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Description
What is the recommended MD5 checker?
Solution
Therecommended MD5 checker is HkSFV (download attached file).
HkSFV uses CRC-32 and MD5 technology to validate the integrity of files that you have downloaded or moved through a potentially unstable medium (burnt
to CD, transferred over the Internet/LAN). HkSFV can verify your files in seconds and is compatible with Win-SFV and md5sum.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
12
Di750 Miscellaneous
HkSFV is the simple, easy and most automatic application to create or check SFV and MD5 files.
What is an SFV?
An SFV file is a tiny list of files and CRCs, which allow you to check to see if the files you have downloaded are exactly what you are expecting. The CRC
algorithm used in SFV files allows you to see if the file you have has been changed, even a single byte, since the SFV file was created.
What is an MD5?
MD5 did not exist until somewhat recently, as md5sum is a popular UNIX format similar to SFV and UNIX does not use file extensions the way Microsoft®
Windows-based systems do. MD5 uses the md5 algorithm to computechecksums, rather than the CRC-32method used by SFV. The md5 algorithm is almost
as fast as CRC-32, but it is much more accurate at detecting changes in files.
Some key features of HkSFV:
Easy installation and automatic uninstallation (leaves no trace in the registry, even goes one step further than most programs and restores previous file
associations when you remove it)
One-click creation and checking of SFVs and MD5s
Flawless & smooth upgrading to new versions (simply install the new version)
Automatic association with SFV files, and an option to fix file association when other programs steal it
Handles SFV and MD5 files from any other program invisibly (including files created on *NIX)
Database/cache of previously checked files
Batch SFV and MD5 checking - queue up and check many SFVs and MD5s in one pass, specify a directory and check all the SFVs and MD5s in that
directory (including subdirectories, if you want)
Automatically find renamed files while checking SFV or MD5 files
Enqueue SFVs or MD5s during file verification
Recursive directory support during creation and verification
Supports creation of .bad and .missing files, or deleting failed files
Drag-and-drop SFV or MD5 file or directory to create/check SFV or MD5
SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
13
Di750 Original jam, no-feed, multi-feed, folding, tearing, skewing, curling
Solution ID TAUS0703403EN* Solution Usage
Description
DF-313/DF-317, original jamming.
Solution
CAUSE: Warped document feeder Low Flapper(s).
SOLUTION: Replace the Low Flapper(s) with the modified part (p/n 13GA45131 - Low Flapper F and p/n 13GA45121 - Low Flapper R). Please refer to the
attached Parts Modification Notices.To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site
at: http://www.adobe.com/products/acrobat/readstep2.html
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
14
Di750 Paper Conveyance jams, no-feed, folding, tearing, skewing, curling
Solution ID TAUS0801765EN* Solution Usage 8
Description
FS-xxx, first page not aligned properly/not stapled in stapled sets.
Solution
CAUSE:Static build-up onalignment plate which causes the first page to stick.
SOLUTION:Wipe affected are with anti-static compound (Brillianize®, Pledge®, dryer sheet, etc.).
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Description
PU-108/PK-1, intermittent J72-38 while copying.
Solution
CAUSE: A dirty or failed size detect board assembly.
SOLUTION: Clean or replace the size detect board assembly (p/n 13NK-9610for PU-108 and p/n 4014-2622-01 for PK-1).
SPECIAL NOTE : Solution contribution by David Aekus, Production Print/SSD
Description
PZ-108/PK-1, J72-38 error when punching. One set of 3 holes is punched near the edge of the paper and a second set is punched in the correct location.
Solution
CAUSE: The sensors in the Punch Unit need to be cleaned.
Description
Paper feeding from more than one tray at the same time resulting in jamming.
Solution
CAUSE: The DC driver board has failed.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
15
Di750 Software/Driver related
Solution ID TAUS0607358EN* Solution Usage 22
Description
The entire print job is stapled instead of each set when printing multiple stapled sets from Microsoft® Word.
Solution
CAUSE:The Collate option in the Microsoft® Word dialog box is selected.
SOLUTION:When printing and stapling multiple sets, the Collate option in the Microsoft® Word dialog box must be deselected.
SPECIAL NOTE : Solution contribution byEd Bellone and Mark D'Attilio, Production Print/SSD
Description
When printing from Microsoft® Office Excel using authentication and printng several spreadsheets within the same document, the authentication dialog box
pops up for each spreadsheet page.
Solution
CAUSE: Improper selection in the printer driver.
Description
"Device can not print in accordance w/guidelines pick another printer" message when trying to print postage from Stamps.Com.
Solution
CAUSE: Driver incompatibility.
SOLUTION: Stamps.com states that they will not work with Konica Minoltadrivers.The only thing they will do is print labels, and you have to purchase the
labels from Stamps.com.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Description
Slow printing issue when utilizing Macintosh® OS 10.4.x.
Solution
CAUSE: Issue with the CUPS daemon configuration file on Macintosh® OS 10.4.x. being corrupt.
SOLUTION: The old CUPS daemon configuration file must be deleted and a new one created. Please see the attached document for instruction on how to
remove and re-create the daemon configuration file.
SPECIAL NOTE : Solution contribution by Tim Blevins - KMBS/Cleveland
Description
"CWS must close" message when checking properties in Command WorkStation™ andthe job properties will not open.
Solution
CAUSE:Incorrect version of Command WorkStation™.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
16
Di750 Software/Driver related
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
17
Di750 Warm-up, wrong display, incorrect operation, lock-up
Solution ID TAUS0613434EN* Solution Usage 40
Description
SC90-01 at power up.
Solution
PROBABLE CAUSES:
1.Failure of the ADU drive board due to a short. An ICP on the ADU boardmay beOPEN.
Note : Service code may have occurred after a jam in the ADU.
Please:
Inspect the wiring harness, solenoids, fans and motors in the ADU section.
2. The connection at the rear of the ADU tray has loosened and is not making a proper connection. Inspect the wiring harnesses in the ADU section.
Reseatany connections of the ADU umbilical wiring harness on the ADU tray and at the rear of the machine below the fixing unit. Verify proper operation.
Description
Intermittent SC46-06, SC46-90, or SC46-91.
Solution
CAUSE: There is an image processing board FlashROM version incompatibility.
Description
ISW DATA ERROR 41 when attempting to flash the firmware.
Solution
CAUSE: A printer is attached to LPT1 preventing the ISW utility from sending the file to LPT1.
SOLUTION: Remove the printer (or other device) that is attached to LPT1.
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
18
Di750 Warm-up, wrong display, incorrect operation, lock-up
Description
J32-11 or F53-12 at power up.
Solution
PROBABLE CAUSES:
1.The wiring of the vertical conveyance unit (right side) is pinched by the lower right side cover (p/n 55VA12061 for 7075/FORCE 75 ;p/n 56GA12060 for
7085/FORCE 85 ; p/n 4014-1846-01 for Di750 ; p/n 4027-1449-01 for Di850 ) resulting in a damaged printer control board.
Inspect the conveyance wiring and repair any damaged wiring using a suitable insulating material. Ensure that the wiring is secured in all clamps and position
the wiring so there is no contact with the lower right side cover. Also inspect that if, an LCT is installed, the LCT is not pinching the wiring. If, after the wiring is
repaired, the code still exists, replace the printer control board (p/n 55VA-9021 for 7075/FORCE 75 ; p/n 56GA-9020 for 7085/FORCE 85 ; p/n 4014-3033-01
- PWB assembly for Di750 ; p/n 4027-1391-01 - PWB assembly for Di850 ).
Note : Amodified conveyance wiring harness (p/n 55VA90252 for 7075/FORCE 75 or p/n 56GA90251 for 7085/FORCE 85 ) is available which makes
routing of the harness easier.
Description
SC60-03 service code at power up. Condition can be cleared for a few seconds but returns immediately.
Solution
CAUSE: There is no initial communications between the logic of theMFP main body and thedocumentfeeder (DF-313/DF-317/EDH-2/EDH-5).
SOLUTION: Check the connections between thedocument feederandMFP by unplugging and reseating all of the electrical connections.
Make sure thedocument feederis not isolated by checking DIPsw 18-4 in the [25] Service Mode =>Soft Switch Setting Mode. The Soft Switch should be
set to "OFF" indicating thedocument feederis not isolated.
If all other checks fail to resolve the service code issue, replace thedocument feederCB (p/n 4014-3140-01 for the Di750/7075and p/n 4027-2084-01 for the
Di850/7085).
Description
"Please wait warming up" message. No malfunction codes are indicated.
Solution
PROBABLE CAUSES:
1. Incorrect line voltage.
Please check the wall outlet for the proper voltage. The line voltage should be 230V AC -14% to +10.6% (aproximately 208V AC is considered normal).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
19
Di750 Warm-up, wrong display, incorrect operation, lock-up
Description
"Please load 5.5x8.5" message when small originals are placed on the glass.
Solution
CAUSE: This is the default mode. Paper size and magnification ratios must be manually selected.
SOLUTION: To make it easier for users who often copy small originals from the platen, it is recommended to select the desired paper tray and magnification
ratio and then store the selections under a job in job memory. Whenever small originals are to be copied, this job should be selected from job memory.
Note : The small original setting can be changed from 5.5x8.5 to 8.5x11 using the Key Operator Mode/Memory Switch Settings/Platen original-size detect
(SMALL).
Description
Four paper drawers indicated on the LCD when there are actually only three.
Solution
CAUSE: Incorrect soft switch setting.
SOLUTION: Please set soft switch 28, bit 2 to OFF (in the 25 mode) to return to a normal display.
Description
SC90-xx (including SC90-01 and SC90-02) and/or SC93-xx service codes are generated, sometimes with jamming in the paper reverse section of the MFP.
Solution
CAUSE: There are two wire harnesses in the ADU section that may be short-circuited.
SOLUTION: Visually inspect the ADU section for wire harnesses that have been shorted. If the wire harness for SD2 (paper reverse gate solenoid) has been
pinched, repair the wire harness by wrapping it with electrical tape. Apply a high temperature locking agent to the threads of the shoulder screw and retighten
the screw. Please see bulletin 4404 for details.
Note : To view the above PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Description
J21-2.
Solution
CAUSE: The Dmax sensor is detecting paper during idling.
SOLUTION: Check for paper blocking the Dmax sensor located by the Cleaning Section, around the Drum.
Description
F67-08 or SC67-08 when using the RADF/EDH.
Solution
CAUSE: The RADF/EDH paper feed assembly is jammed preventing movement to allow the PS315 (tray upper limit) to be actuated by the upward movement
of the lift tray.
SOLUTION: Correct the source of the bind and ensure that when the feed assembly is is raised by the lift plate, the upper limit sensor is flagged.
Description
SC52-07 error code (Fan MT-3).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
20
Di750 Warm-up, wrong display, incorrect operation, lock-up
Solution
CAUSE: The front door interlock switch has failed.
Description
J10-01 when feeding from the bypass tray.
Solution
CAUSE: Loss of drive to the bypass unit due to a contaminated or failed bypassdriving gear.
SOLUTION: The bypass driving gear is a one-way gear that allows drive to the bypass feed when the loop motor (M6) drives in reverse. If the one-way gear
fails, there will be no drive to the bypass feed. Clean the gear and shaft with alcohol. If the problem remains, replace the gear (p/n 4014-2190-01).
SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD
Description
When feeding from Tray 4 (LCT) the machine will stop feeding and continue to cycle.
Solution
CAUSE: The feed sensors of the LCT are contaminated with paper dust.
SOLUTION: Access the LCT feed and pre-registration sensors and clean the sensors and surrounding area of paper dust.
SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
21
Di750
Solution ID TAUS0620249EN* Solution Usage 238
Description
Why toner/developer is spewing and falling onto the T/S corona resulting in light areas and marks/blotches on copies.
Solution
These symptoms can normally be corrected by following the recommendations as listed in the 7075/7085 Correction Checklist for Background and Spewing
and the Toner Spill Troubleshooting document.
IMPORTANT : The magnet angle area should be checked. If the part is cracked and developer is spilling out from the developing unit refer
toattachedBulletin Number 4832 for corrective measures.To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free
from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Description
Can the Interface Kit N from a Di850 work as a replacement for the Di750 Interface Kit L?
Solution
The Interface Kit N from a Di850 can not be used as a replacement for the Di750 Interface Kit L. Even if the firmware was changed by re-flashing the
Interface card, the controller interface will not function. This has been confirmed in the field and in house. Even though the controller interfaces appear
similar in design, the solid state components are different.
Description
The Pi7500 controller enters a perpetual boot condition until the firewire is disconnected. In addition, the VIF is grayed out in the [25] service mode -- ROM
Versions. Each time a new VIF was installed, it would function for a short time and then fail.
Solution
CAUSE: Failed PMB (power management board) and/or DC power supply #2. A short circuit in these boards can cause the VIF (Video Interface) to fail.
SOLUTION: Replace the PMB (Power Managment Board) and the DC Power Supply #2. In addition, the failed VIF (Video Interface) also needs to be
replaced.
Description
List of equipment that is no longer being supported.
Solution
Please see attached Product & Technical Support Bulletins 1792 and 2443 andMarketing Bulletin#07-GB-016.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
Unable to install 32-bitdrivers on a Microsoft Windows 2003 64-bit server formigration to the 32-bit clients.
Solution
The 32-bit driver files are not recognized when attempting to load on a 64-bit system, therefore, the files must be pulled from a 32-bit system in order to add
additional driver support on a 64-bit server:
1. After installing the 64-bit driver on the server, install the matching 32-bit(PCL, PostScript Visual, PostScript (Plug-in) or PostScript (Adobe) driveron one of
the clients.
2. The driver files will be placed in C:\WINDOWS\inf folder on the client.
3. Share this folder on the network so that the 64-bit server has access.
4. From the server, when adding additional drivers, browse to the shared folder on the workstation
5. Select the appropriate .inf file from the shared folder on the client - the driver files will then be pulled over to the server to support other 32-bit clients when
migrating the driver files.
Note: It is important to install the same type of driver on the client to match the driver installed on the server.
Description
When searching solutions by models,referenced links for the documentsare notaccessible.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
22
Di750
Solution
CAUSE: This is a search of the printed database. The links are locatedwithin the solution in the database.
SOLUTION: Copy the solution ID number into the Knowledgebase look-up Keyword field and select Search to access the solution complete with active links
to attached documents.
Note : If there is an actual 'dead' link within the solution, please send an E-mail to cses@kmbs.konicaminolta.us with the solution ID number and please
identify the link.
Description
How to set up scanning without using PageScope Light.
Solution
This can be done using the copier based Web Utilities. Perform the following steps:
1. Set up a TCP/IP address in the copier:
a. Set soft switch 22-0 to ON.
b. Enter KEY OPERATOR MODE.
c. Select SYSTEM INITIAL SETTING.
d. Select IP ADDRESS SETTING.
Note : The network drop for the print controller can be temporarily used to connect or a second drop can be used for a permanent connection. This drop is
connected directly to the RJ45 connector on the copier.
2. Launch a web browser from any PC on the network and enter the copier TCP/IP address to run the Web Utilities:
a. From the main screen select ENVIRONMENT SETUP.
b. When asked for a password, enter the Key Operator password set up in the 25 Mode (the default is 0000).
c. Select SCAN TRANSMISSION SETTING. FTP, E-mail and HDD scan one touches can be registered here.
d. Use the ENTRY LIST key to view all one touches and to change or delete entries.
Description
Making copies on the Di750 the image is shifted when using the bypass to make copies. The tray adjust and registration adjustments have all been done, but
the issue remains.
Solution
The tray adjustment indicated in service manual is incorrect. Please see Service Bulletin 3031 for additional information. A revised service manual is also
available. The part number for the new manual is 7662- 4014-22.
Link
Description
The message "Copier Warming Up" is indicated and the machine will never come to a ready state.
Solution
CAUSE: The heater electrifying brush is bound causing a poor connection to the drum.
SOLUTION: Check the heater electrifying brush at the rear of the drum. The heater electrifying brush is a carbonized contact that is spring loaded. This brush
makes contact with the rear of the drum and provides power to the drum heater. Check connection. Replace worn brushes if needed. Part number is
4014-1889-01 (two are required).
Description
SC41-10 was indicated during a print job.
Solution
CAUSE: The M17 lock signal is not being detected after a speed change was made. This issue involves the rotation of the polygon motor so the connections
to this motor should be checked along with the polygon mirror drive board and printer control board.
Description
When combining staple and duplex on the Di750, the paper jams. When combining staple with non-duplex the copier prints fine. Registration has been
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
23
Di750
adjusted and the main board has been replaced.
Solution
CAUSE: Incorrect firmware version of the finisher.
SOLUTION: The firmware version of the finisher should be a minimum of version 45. Please check Bulletin 3061e and Bulletin 3430b for the latest
firmware.
NOTE: When making copies utilizing the FN-4 or FN-104 and/or the TMG-1 it is possible that the copier will display service codes SC77-03, SC77-33 and
paper jams including J73-07 falsely. These can also be corrected by upgrading the firmware.
Description
Part/Item number for the interface kit (I/F Kit) to connect a Pi7500.
Solution
I/F Kit L (Item #4691-101).
Note: Interface kits for other machines (such as I/F Kit N for the Di850) are not compatible with the Di750/Pi7500.
Description
SC 93-06 service code.
Solution
CAUSE: The switchback pivot screw backed out and pinched solenoid wire against the cover which opened the ICP on the ADU board.
SOLUTION: Tighten the switchback pivot screw and check the solenoid wire. Replace the ADU, if necessary.
Description
SC46-91 as soon as the print key is pressed.
Solution
CAUSE: Incorrect or non-functioning memory module.
SOLUTION: Replace the memory on the ICB (Image Control Board). If optional memory had been installed, remove it or if the original memory is being used
replace it. Also make sure that current firmware is being used in the copier. Please see bulletin 3061F for additional information.
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
2. To open the ZIP file(s), WinZip* must be installed. WinZip can be downloaded from the [[WinZip website| URL http://www.winzip.com/ddchomea.htm]].
The file can either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view.
Description
SC56-04 when trying to connect to MicroPress* v6.
Solution
CAUSE: Communication problem between the PrintLink and the copier/printer.
SOLUTION: Please check the firmware in the PrintLink and the connections between the PrintLink and the copier. Please refer to bulletin 3784a and the
MicroPress Installation Guide for additional information.
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
24
Di750
Solution ID TAUS0636383EN* Solution Usage 1
Description
Part number for the fuser knob.
Solution
Please refer to bulletin 3759 .
Description
SC 00-00 is displayed on the machine.
Solution
CAUSE: This usually indicates a problem with the EDH (RADF), sometimes that the paper feed assembly is bound.
SOLUTION: Please make sure the document feeder's paper feed assembly moves up and down freely. It is possible that the code is generated by a faulty
PRCB or ICB.
To trouble-shoot this issue, begin by re-flashing the firmware in the copier. If re-flashing the copier fails to clear the SC00-00 service code, disconnect the
EDH to isolate the issue. If the issue is cleared by removing the EDH the problem is within the EDH. If nothing in the EDH is binding, the DFCB (Document
Feeder Control Board) could be faulty.
If the code does not clear when the EDH is disconnected the ICB (Image Control Board) could be faulty. Please check all connectors to the ICB and
PRCB(Printer Control Board).
If the ICB fails to resolve the issue the PRCB should be replaced.
Description
Are part numbers available for the shafts in Hopper Unit (C)?
Solution
These parts outlined with dotted lines on page 53 of the Di750 Parts Manual are not available individually. Please order the Hopper Assembly (p/n
4014-3265-01).
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
J 11-05 is displayed. "Close ADU unit or any tray except tray 1" is displayed. "Please remove a paper following a guide" is also displayed.
Solution
CAUSE:
J 11-05 indicates a problem with PS48.
SOLUTION:
To troubleshoot this problem, swap the tray 1 sensor (PS 48) with the one in tray 2 (PS 50). If the jam code changes to J 12-05, the sensor was bad. The
sensor that was originally in tray 1 needs to be replaced.
Description
SC34-01 at power up. The code can be cleared but returns after a few seconds.
Solution
PROBABLE CAUSES:
1. Failed TH1 sensor.
Replace the sensor.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
25
Di750
Replace the board (p/n 4014-3260-01).
Note: Check the TH1 thermistor, making sure that it is adjusted to the proper height and is connected properly.
Description
"Please close EDH cover" message although the EDH is already lowered.
Solution
CAUSE: Incorrect soft switch setting.
Description
The paper lift mechanism in the large capacity paper cassette is overdriving.
Solution
CAUSE: There are two interlock switches used to interrupt power to the lift tray motor M101. The two interlock switches are the lift tray interlock MS101 that
opens when the large capacity cassette top cover is opened and the lift tray interlock switch MS102 that is opened when the paper in the tray pushes against
the paper feed roller. A spring attached to the top cover and the paper feed roller unit is used to move the paper feed rollers out of the way of the lift tray; to
aid in the insertion of new paper when the paper supply runs out. This spring, by moving the paper take up rollers out of the way of the paper path, prevents
the paper stack from engaging the paper feed roller if it should be lifted by the activation of the lift tray motor M101. This prevents the lift tray interlock switch
MS102 from opening up and cutting power to the lift tray motor M101. If the lift tray interlock switch MS101 is 'cheated', the result is the lift tray motor M101
not stopping and the paper lift continues until catastrophic damage is generated in the tray lift mechanism.
SOLUTION: If it is required to override the lift tray interlock switch MS101, it will be necessary to remove the spring connecting the top cover and the paper
feed unit. Open the top cover and remove the spring from the paper feed unit. Once the spring has been removed the paper feed rollers will lower into a
position so that when the lift tray interlock switch MS101 is 'cheated' and the paper begins to be lifted by the lift tray motor MS101, the power supplied to the
motor will be interrupted as soon as the paper stack engages the paper feed roller and the lift tray interlock switch MS102.
Description
"Now warming up" message. No malfunction codes are displayed.
Solution
CAUSE: The fuser lamps illuminate, however proper/full temperature is not reached due to failing lamp filament.
SOLUTION: Check the fuser lamp and replace if necessary. If the lamp is OK, please replace the ADU board.
Description
The Di750, Di850, 7075, 8085 displays either SC80-02, and SC50-01 service codes on start up.
Solution
A communications issue exists between the ICB, Image Control Board and the PRCB, Printer Control Board.
Unplug and reseat the ICB and the ICIFB. Unplug and reseat all of the connections to the PRCB to insure the two boards have a solid electrical connection
to each other.
If the problem persists the ICIFB should be replaced.
The part number for the ICIFB is 4014-3248-01 for the 7075 / 7085 and 4027-1396-01 for the Di750 / Di850.
Description
Microsoft®-certified printer drivers - PCL, PostScript, PostScript (P)and PostScript (V).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
26
Di750
Solution
The Konica Minolta Microsoft®-certified printer driverscan bedownloaded fromthe Konica Minolta Download Selector. Access the Selector from theKMBS
public site ( http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS,
Drivers, Firmware and more'.
These drivers will be shown as a WHQL ( W indows H ardware Q uality L abs)Download.
Access the Download Selector and type WHQL in [Find downloads:],then click on Search->.
Description
How to determine what version of Sun Java™ is installed on a Microsoft® Windows workstation.
Solution
To determine what version of Sun Java™ is installed, perform the following:
1. From a command prompt type:java -version
2. Press Enter.
3. The version of Sun Java™ will be indicated. If the command is not recognized then Sun Java™ is not installed.
Description
When the finisher is installed and it reaches its limit of stapled sets, the customer must remove all stapled sets to continue printing. Can the copier be set to
continuously print when the finisher is installed?
Solution
Set dipswitch 15 bits 3 and 4 to 1. This causes the copier to disregard the finisher error request.
Description
How to print to a printer on a Microsoft® Windows XP PC from a Macintosh® running OS version 10.4.x.
Solution
Please perfrom the step-by-step procedure mentioned in the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
Site requirements, Di750.
Solution
Site Requirements 20 and 30 Ampere Machines . See also Konica Minolta Site Requirements Forms ( FO-9 and FO-10 ) which provide the site
requirements to which customers must conform before having any Konica Minolta 20 or 30 ampere models installed.
Note: To view the above PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
J11-01 service code displayed. The paper jammed at take-up seems to have a large buckle. The problem is intermittent.
Solution
There may be a bind in the second feed rollers. The paper seems to have too much buckle in it. The bushings on the second feed rollers and shaft should be
cleaned. Replace the bushings if the cleaning does not remedy the problem.
Description
When making a proof copy for a job containing several sets of copies, if the Interrupt Key is depressed and an interrupt copy is finished (after the interrupt
copy mode is released), print quantity for the preceding job becomes 1.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
27
Di750
Solution
CAUSE: Outdated firmware.
SOLUTION: This problem can be resolved by upgrading the firmware in the copier to the [[latest version| URL
http://techweb.konicabt.com/DownloadSelector/SearchResults.aspx?CNAME=di750]].
Description
How can the maintenance counter be set to click twice when feeding 11x17 paper?
Solution
To get the maintenance counter to count twice for 11x17 output, set DIPSW8-6 to "ON" in software switches section of the adjust mode. See page 1-9 in
the Di750 Service Manual for additional information.
Description
Are the parts from other copiers based on the Konica 7075 (such as the Mita VI7360, Pitney Bowes DL750, and OCE' 3275) compatible with the Di750?
Solution
The Di750 has some differences such as the covers, toner bottle, toner add mechanism and flash ROM information. For example, there are physical
differences between the 7075 toner bottle and the one designed for the Di750.
There may also be some undocumented differences in the hardware, circuit boards, and controls of the copier. Parts should not be substituted.
Description
Light copies and/or poor fill after initial installation.
Solution
CAUSE: This can be caused by performing certain adjustments out of sequence.
Description
There is no selection for the Di750 in ISW.
Solution
CAUSE: Incorrect ISW version.
SOLUTION: Verify that minimum ISW version is 3.39E . Refer to bulletin 3529A .
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
2. To open the ZIP file(s), WinZip* must be installed. WinZip can be downloaded from the [[WinZip website| URL http://www.winzip.com/ddchomea.htm]].
The file can either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view.
Description
The staple position is not in proper alignment on all of the copies. Attempts have been made to correct this problem through the adjustment mode, however
the staple position is still not correct.
Solution
SOLUTION: Adjust the stapling position as indicated in the Service Manual. This is a physical adjustment that requires the use of a Philips head screwdriver
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
28
Di750
to make the adjustment. See page 1-123 in the Service Manual for additional information.
Description
"Please load paper in tray 3" is displayed and SC 18-31 is listed in data collection, list output.
Solution
CAUSE: An F18-31 code is generated when PS22 (tray upper limit sensor 3) which has been OFF, is not turned ON within 10 seconds of upward movement
started by the turning ON of M21 (up drive 3). At this time, a trouble detection signal (24V off) is detected. The error code is not displayed on operation
panel. It is displayed only on data collection, list output. The message "Please load paper in tray 3" is displayed on the operation panel because the tray has
not completed ascending.
SOLUTION: Depending on checks, replace M21 (up drive motor 3), DCDB (DC drive board), PRCB (printer control board), or PS22 (tray upper limit sensor 3).
Description
An SC77-07code appears during stapling, after replacing the stapler problem returned.
Solution
Cause: Communication failure from the stapler to the FNCB.
Solution: Check all connections of the stapling unit back to the finisher control board. Verify that the proper voltages "24V" are provided for the stapler motor
M4. If present, replace the finisher control board.
Description
Video interface board will not register.
Solution
CAUSE: The video interface board is not installed in the proper slot.
SOLUTION: The proper slot for installation is the lower one. The upper slot is used for the hard drive option.
CAUTION: Installation of the video interface board into the wrong slot can damage the board.
Description
A false error message SC46-14 is displayed when the cover inserter A option is used. All recommended checks in the Troubleshooting Guide fail to identify
the cause of problem.
Solution
Confirm that the wire harnesses for the cover inserter A are properly routed in their saddles. There are several motors and clutches that can cause electrical
noise sufficient enough to cause the logic to falsely indicate a problem.
Description
The scan button is grayed out.
Solution
PROBABLE CAUSES:
1. Incorrect Pi7500 system software. Scanning requires v. 2.0 (or higher) system software in the Pi7500 print controller and current firmware in the copier.
2. Incorrect switch settings on the copier. Soft switch settings in the copier must also be set correctly. Soft switch 23, bit 4 must be turned on to enable
scanning.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
29
Di750
Solution ID TAUS0625238EN* Solution Usage 0
Description
Paper trays one and two are not being detected.
Solution
If the first and second paper tray are not detected check service mode 25, SW18 to reset the drawer. These settings will toggle to "1" if a background
malfunction is generated.
Description
Paper size is not being selected when originals placed on the glass.
Solution
CAUSE: Sensor malfunction.
SOLUTION: Use the tech rep mode to determine if the sensors are working properly. Use the 47 Mode, input checklist code 31, multi-mode 1 through 8 for
the platen sensors. For the document feeder (EDH) use code 60, multi-mode 1 through 15 for the RADF sensors. Please refer to service manual for additional
information.
Description
The machine is indicating an Error message 2 on the control panel. There is no information in the service manual on this malfunction.
Solution
Cause: The Error message 2 is associated to a problem with the image density sensor.
Solution: Check the image density sensor for a toner build-up, and also check for a proper electrical connection.
Description
SC 56-01 error message is displayed.
Solution
CAUSE: Poor connection.
SOLUTION: To correct error message SC56-01, try re-seating the connectors on the printer control board.
Description
The Di750 displays an F13-01 code?
Solution
An F13-01 code is generated when a trouble detection signal is detected two consecutive times (the first signal is ignored) in 4 seconds after turning ON of
M4 (paper feed). Depending on checks, replace M4 (paper feed motor), or the PRCB (printer control board).
Description
SC 13-02 is displayed.
Solution
CAUSE: An SC 13-02 code is generated when a trouble detection signal is detected two consecutive times (the first signal is ignored) in 2 seconds after
turning ON of M101 (LT paper feed motor).
SOLUTION: Depending on checks, replace M101 (LT paper feed motor) or the LTDB (LT drive board).
Description
How to enable or disable the key beeps.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
30
Di750
Solution
To enable or disable the beep option, perform the following:
1. Enter the key operator mode.
2. Entere memory switches, set beep, number 26. Key click.
3. Enable this mode.
Information can be found in the user's manual.
Description
Difficulty performing the registration adjustments for the Di750. The test pattern that prints out is more than 20mm off.
Solution
The incorrect adjustment procedure was used.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
* Trademark ownership information
Description
How to reset the electronic total counters in the Di750.
Solution
For obvious reasons the main electronic counter can not be cleared in this copier. The the consumable counters and most data collection counters can be
reset. Refer to the Di750 Service Manual, adjustment section page 1-20 for details. Be aware Replacment of the memory board clears the counters.
Replacement requires a lengthy adjustment procedure be performed. Copy quality is affected because many of the initial charge and image settings are
made at the factory using special tools. These settings are lost when a new memory board is installed.
Description
The list of adjustments stated in the Di750 service manual does not correspond with the service bulletin.
Solution
There is an amended list of adjusments for the Di750 in Service Bulletin 3033.
Link
Description
How to adjust the paper cassette using the Di750 manual. The proper size paper is not being indicated.
Solution
Changes have been made in reference to the adjustments for the paper cassette. See Service Bulletin 3031 for more details.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Why don't I see any jam and service codes when I print out the service reports from the Di750?
Solution
To view service data set DIPSW 30-1 to "1" in the 25 adjust mode. See the Service Manual, pages 1-12 for additional information.
Description
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
31
Di750
What is the recommended volume for the Di750 ?
Solution
Information regarding recommended volume and copier specifications can be located in the new product information guide. See the information posted on
the PartnerLink web site.
Link
Description
Can you use 7075 toner in the Di750, since they are similar machines?
Solution
7075 toner can't be used in the Di750, as the toner bottles are different. The holders between the machines are also keyed differently.
Description
Paper jamming at the registration roller. Jams occur at the same location each time.
Solution
CAUSE: Faulty sensor PC45 or PC55 or faulty registration clutch.
SOLUTION: For registration roller jams, check the functionality of PC45 and PC55. Use the I/O checks in mode 47 to verify the sensor operation.
If persistent paper jams at the registration roller is not corrected after sensor checks, please check the registration clutch. (If jamming is occurring from only
one paper tray you can swap clutches between drawers.) Also check for dust in the paper dust collector at the registration roller and make sure it is seated
correctly. Lubricate the registration and transport roller bushings.
Description
After refreshing the copier or after replacement of the ICB board, the copier will no longer indicate the proper paper size in the paper trays.
Solution
PROBABLE CAUSES:
1. The adjustment procedure on page 1-59 of the Service Manual does not set the paper trays properly.
See bulletin 3031 for a revised adjustment procedure for the paper feed trays.
2. Corrupt firmware.
Reprogram the graphics control board using the In System Writer utility. Detailed instructions can be found in the Service Manual on pages 2-1 to 2-12. Also,
information on current flashROM data can be found in service bulletin 3061E .
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
One of the paper trays, or the EDH, is shown as not available on the front panel of the Di750.
Solution
Enter 25 mode, check the settings for soft switch 18. All bits should be set = 0.
Refer to page 1-11 of the Field Service Manual.
Description
The copier locks out when printing large jobs from a MicroPress.
Solution
CAUSE: Insufficient memory installed in the Di750.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
32
Di750
Solution ID TAUS0625271EN* Solution Usage 0
Description
Finished booklets can no longer be made after upgrading the copier to the latest ROM version.
Solution
Upgrade firmware to the latest version. See Technical Bulletin 3061A and
Technical Bulletin 3061F for details.
Note: The latest version system software and firmware is available on the Konica Minolta FTP site .
Description
Cannot print after installing the Pi7500 print controller. Also, the configuration page does not print. The test page is processed from the controller, but no
pages are printed.
Solution
CAUSE: Firmware needs to be upgraded.
SOLUTION: Upgrade firmware to the latest version. It is recommended to check the flash ROM version of the copier. Use the 25 service made to review the
installed ROM versions. See Technical Bulletin 3061F for the latest flash ROM versions.
Notes:
1. If the machine's operation mode can not be changed to Print Mode by using the Mode Button on the control panel please make sure soft switch 23, bit 4 is
ON. This switch also enables scanning, as outlined in Technical Bulletin 3061F.
2. The latest version system software and firmware is available on the Konica Minolta FTP site .
Description
Intermittent jamming on take-up, especially after a long print job. This problem seems to be present from all of the paper trays.
Solution
CAUSE: Defective DC drive board.
SOLUTION: Refer to Bulletin 3372 . This Service Bulletin is in reference to issues with the drive boards for the copier's take-up system. If intermittent take-up
jams are present, replace the DC drive board with a new style one.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
The fuser section is not turning on and the paper cassettes in the copier are all reading metric paper sizes. An SC36-03 error may be displayed.
Solution
CAUSE: Faulty interlock.
SOLUTION: If there is no fuser operation or erratic/false copier operation, the front door interlocks should be replaced.
Description
The Di750 displays an SC46-14 after making several copies.
Solution
SC46-14 indicates an issue involving the optional memory. If you have any optional memory installed remove it and see if problemcorrects itself. Replace the
ICB board if removing the optional memory does not correct the problem.
Description
What is service mode "18" listed when I enter the service mode? I can not seem to find anything listed in the service manual.
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
33
Di750
CAUSE: Service mode "18" is used when the copier is set up during the assembly process. It is not used for service.
SOLUTION: Disable this display by entering the "25" adjusted and change DIPSW30-0 to 0. In addition check DIPSW31- (0-7) and DIPSW32-(0-70) , these
switches are also used during manufacture. All of their bits should be set to 0 for proper copier operation.
Description
What is the part number for the entire control panel assembly? The parts manual does not list this information, only individual parts.
Solution
SOLUTION: The part number for the panel is 4014-3268-01. In the manual, the image of the control panel is integrated with the individual parts of the panel.
Description
Duplex jams when feeding 110lb stock. The Operators Manual and Service Manual both indicate that the copier will feed 110lb paper.
Solution
CAUSE: The recommended paper weight for duplex is 45lb. The 110lb paper is too thick to be fed properly during duplex.
SOLUTION: Copies can be made by single-feeding first, and then reloading paper trays and feeding again. This is not recommended for large runs because
feed tires may need service sooner due to toner contamination from pre-printed stock.
Description
How to program the flashROM using ISW, Di750.
Solution
Please see bulletin 3104 which provides step-by-step instructions on the ISW (In-System Writer) Flash ROM upgrading procedure. For additional details,
refer to the ISW Service Manual . The current version of ISW is described in bulletin 4488A .
Please see bulletin 3104 which provides step-by-step instructions on the ISW (In-System Writer) Flash ROM upgrading procedure. For additional details,
refer to the ISW Service Manual . The current version of ISW is described in bulletin 4488A .
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
2. Click on the blue-highlighted links within the PDF(s) to view additional details.
3. To open the ZIP file(s), WinZip* must be installed. WinZip can be downloaded from the [[WinZip website| URL http://www.winzip.com/ddchomea.htm]].
4. The WinZip file(s) should have the extension changed from ZIP to EXE. When renamed, the files are self-extracting.
5. The most recent ISW Trns tool can also be downloaded from the [[Konica Minolta FTP site| URL ftp://kbtdigital:kx15@ftp.konicabt.com]].
Description
Dark background on all copies.
Solution
CAUSE: Toner density is seti too high.
ASOLUTION: Toner density of the developer can be changed by changing soft switch 23-2 and 23-3. The toner density can be reduced in increments of
(.5%=0,1), (1.0%=1,0), (1.5%=1,1). For this feature to work properly, it is necessary to make sure the latest firmware is installed. See Service Bulletin 3061e
for additional information.
Description
How to configure the PrintStation 075m to connect a Di750 to a MicroPress server.
Solution
If there is a communication problem between the MicroPress server and the print engine, please verify that the finisher is compatible with MicroPress. Certain
options for the CF2001, CF9001, and Di750 are not supported by MicroPress, possibly causing communication errors. Please refer to Bulletin 3541
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
34
Di750
Solution ID TAUS0625288EN* Solution Usage 0
Description
How to troubleshoot paper jam indication J31-01 is displayed.
Solution
Check the feed rollers and jam sensors and replace if necessary. Replace DC driver board as indicated in bulletin 3372 .
Description
Paper jams in the ADU section near the registration sensor.
Solution
SOLUTION: Clean the feed rollers and check the sensors and clutches. Clean the registration roller bushings and the one way bearings on the gears that
provide drive from M6 to the registration rollers. Replace the MC1 registration clutch.
Description
Service code SC 46-01 is indicated.
Solution
PROBABLE CAUSES: This code is triggered by the lack of 12VDC being supplied to the print head.
Please check the following:
1. Check for 12VDC at the Image Control Board. If voltage is missing, the main power supply may need to be replaced.
2. Also check the voltage being supplied to the copier; poor wall voltage may also cause this issue.
3. A less likely possibility is a faulty print head (write unit).
Description
Paper jams in the finisher when making 1-2 sided copies. The print job is set up as a programmed job and it is being recalled when copies are being made.
The problem does not seem present when walk-up copies are made.
Solution
Upgrade the firmware to the latest version. Please see Service Bulletin 3061f for the latest firmware information. This issue affects copiers with serial
numbers before XX1909.
Description
The machine is intermittently jamming in the fuser. Checks of feed tires and paper path failed to show any mechanical problem. The management list, when
examined, indicated a large quantity of fuser exit jams.
Solution
CAUSE: Firmware.
SOLUTION: Upgrade the Flash/ROMs on the copier. A timing issue exists with the very early release of the firmware for this copier. Please see Bulletin
3061e for the latest ROM information.
Description
The large capacity cassette C-305L is not listed in the Available Options area on the Configuration tab (the Optional Trays list in the Installable Options area
on Windows2000 and Macintosh) in the Printer Properties.
Solution
CAUSE: The C-305L is not supported directly with the version 1.01 print driver. The following options are supported; FN-4, FN-104, C-305, and cover inserter
A.
SOLUTION: Use the C-305 selection in the printer properties if the C-305L is connected to the copier. Issues may exist when using metric or larger paper
sizes.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
35
Di750
Description
The Di750 displays an SC70-01 service code.
Solution
This is a communication error between the FN104/FN4. Check all of the connectors to the FNSCB (Finisher control board).
Description
The Di750 displays a SC52-02 service code. What needs to be checked to resolve this issue?
Solution
Make sure FM3 (main Body Cooling Fan) is turning in the copier. Use the 47 service mode to test. If motor fails to turn, replace motor.
Description
SC32-01 error message.
Solution
PROBABLE CAUSES:
1. Failed FM2 (developer suction fan motor). Verify that FM2 turns using the 47 service mode. Replace motor as needed.
Description
Background on all of the copies.
Solution
PROBABLE CAUSES:
Description
Problems installing the firmware using the ISW utility. Error messages are displayed or the LCD is blank.
Solution
PROBABLE CAUSES:
1. Incorrect parallel port setting.
Check the port setting on the computer. Enter the BIOS section and make sure the printer port is not set for ECP. Using ECP mode may prevent the flash
ROMs from loading (for additional details, please see the ISW Service Manual ).
3. Other errors.
If a problem occurs while downloading other files the copier will display an error message. Regardless of the error message, the copier must be shut down.
Allow the PC to time out and display an error message. Click OK. Restart the copier in the "25" mode. Attempt to download the file again. For step-by-step
instructions on using ISW please see bulletin 3104 .
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
SC56-02 service code is generated shortly after accessing the hard drive.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
36
Di750
Solution
CAUSE: Communications problem involving the ICB (Image Control Board).
SOLUTION: First try resetting the code by unplugging the copier completely. If this does not correct the issue, replace the image control board (p/n
4014-3034-01). Refer to page 129 (figure 65) of the Di750 Parts Manual for further details.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
Description
Long warm up time in the morning.
Solution
CAUSE: Room temperature and humidity can affect the warm up time. It also varies according to the condition of the thermistors (including the drum
thermistor).
SOLUTION: Check the thermistors to make sure they are clean. Also use the adjustment jigs for the thermistor to make sure they are properly adjusted.
Description
SC36-06 code after replacing the lower fuser roller.
Solution
PROBABLE CAUSES:
1. Improper gap between the fuser roller and TH4 thermistor. Use the required adjustment jig to check the space between the fuser roller and the TH4
thermistor.
Description
SC28-01 when making copies. Some of the prints are blank.
Solution
CAUSE: This service code indicates an issue with the high voltage power supply HV1.
SOLUTION: Check the connections to HV1 including the charge corona assembly. Make sure that no shorts are present. Replace the HV1 if needed.
Description
At what interval should the cutters on a TMG-1 be replaced?
Solution
The cutters on the TMG-1 should last for 10,000,000 copies. Please see the service manual for information on items replaced at this interval.
Description
Are the parts from a MITA VI7360, Pitney Bowes DL750, and OCE` 3275 compatible with the Di750? All of these copiers are based on the Konica 7075 and
should be the same.
Solution
The Di750 has some differences such as the covers, toner bottle, toner add mechanism and flash ROM information. For example, there are physical
differences between the 7075 toner bottle and the one designed for the Di750.
There may also be some undocumented differences in the hardware, circuit boards, and controls of the copier. Parts should not be substituted.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
37
Di750
Solution ID TAUS0625307EN* Solution Usage 0
Description
The ECM mode does not function after upgrading the Pi7500 to version 2.0.
Solution
Cause: There is a communication problem between the Pi7500 and the Di750.
Solution:
1) Confirm that the proper soft switch settings per service bulletin 3061B "Revised" dated 2/13/02 have been made.
The controller and the copier must restarted after making any changes to the copier's soft switch settings.
2) Check that the controller is also plugged in properly into the copier's power receptacle, not the wall outlet.
3) Refer to bulletin 3061e to be sure the latest firmware has been installed in the Di750.
Link
Link
Description
Di750 "Line Screen" or "Screen Value" specification.
Solution
The value for "Line Screen" or "Screen Value" for the Di750 is 101.6 (lines per inch), based on a standard #1 test chart.
Description
When making copies that utilize corner stapling the position of the staple is incorrect. Also paper jams occur with the TMG-1 trimmer option.
Solution
CAUSE: This is a timing issue.
SOLUTION: Upgrade the firmware of the FN-4/FN104 to version 45 or higher. (Please see bulletin 3430b .) Make sure that the copier also has the current
firmware installed prior to upgrading the EPROM in the FN-4/FN-104. Please see bulletin 3061f for additional information on the current firmware.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
* Trademark ownership information
Description
We have a Di650/ Di750 in our demo room, along with a MicroPress server and a Pi6500. Can the copier be used with both systems?
Solution
Yes. The Di650 and Di750 can easily be switched between MicroPress and an EFI Fiery controller. Please refer to bulletin 02-GB-16 for details.
Link
Description
How to clear a fuser service code (SC 34-xx, SC 35-xx, SC 36-xx).
Solution
Using the 25 mode, soft switch 3, bit 1 must be changed back to 0 (off). To do this, perform the following steps:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
38
Di750
Solution ID TAUS0625320EN* Solution Usage 0
Description
Current firmware for the Di750.
Solution
Please see service bulletin 3061f or use the NSSG [[downloads page| URL
http://techweb.konicabt.com/DownloadSelector/SearchResults.aspx?CNAME=di750]]. Bulletin 3104 has the procedure for completing the upgrade using the
ISW utility.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
* Trademark ownership information
Description
When making copies of pictures or images with heavy background copies have a black band across the page. Normal copies look fine.
Solution
CAUSE: Incorrect settings.
SOLUTION:
In the 25 service mode, check DIPSW 16-7, 16-6, 16-5, and 16-0, which can be used to change the scan density. See page 1-17 in the service manual under
adjustments. Also see DIPSW 5-4 and 5-5, which affect the PWM table when using photo mode. Try using a different PWM table. Table 1 is lighter. See the
service manual for exact details on these changes.
Note: Also make sure that the [[current firmware| URL http://techweb.konicabt.com/DownloadSelector/SearchResults.aspx?CNAME=di750]] is installed.
Description
What kind of interface harness is required for a Hecon controller?
Solution
Third-party counters are not supported.
Description
Paper take up from paper tray 1 is not functioning. After installing a working tray from a known good copier and the paper will only take up approximately 1".
Solution
CAUSE: Problem with DC drive board.
SOLUTION: Please install a new DC drive board. Please see bulletin 3372 for details.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Part number for the C-305L rear cover.
Solution
The part number for the rear cover of the C-305L is 4014-3308-01.
Description
Part number for the C-305L right side cover.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
39
Di750
Solution
The part number for the right side cover of the C-305L is 4014-1534-01.
Description
Can the Di-750 do alpha numeric numbering?
Solution
Alpha numeric numbering cannot be done on the Di750. Page numbering is numeric only.The Di750 supports Stamp and Overlay with the addition of an
optional hard drive.
Description
How to assign a TCP/IP* address to the PrintStation 075m Print Link without using NetFlash because the current TCP/IP address is not known.
Solution
Please refer to bulletin 3285 and run the UDPReceive utility .
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
2. To open the ZIP file(s), WinZip* must be installed. WinZip can be downloaded from the [[WinZip website| URL http://www.winzip.com/ddchomea.htm]].
The file can either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view.
Description
Part number for ordering the ISW (In-System Writer) utility.
Solution
Please see bulletin 3529A . ISW also is supplied when ordering the flashROM CD (p/n 7660-4024-03). For additional details, see the ISW Service Manual
.
Notes:
1. The latest ISW tool software can be downloaded from the [[Konica Minolta FTP site| URL ftp://kbtdigital:kx15@ftp.konicabt.com]].
2. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
After installing a new PK-1 the Di750 shows that a two hole punch was installed even though a three hole punch was actually installed. I have updated all of
the firmware in the copier and accessories and I am unable to clear this condition. Is there anything that I need to do to have the copier show three holes
instead of two?
Solution
Make sure that DIP switch 22-2 is set to "0" and dip switch 22-1 is set to "1". These are the required switch settings for three-hole punch. If the soft switch
settings are set to all "0" or all "1" the copier will indicate two hole punch. Please see the PK-1 service manual for additional information.
Description
When I try to run auto drum potential after replacing the drum I get an Error 3 code appearing in the adjustment screen.
Solution
Cause: The Error 3 occurs when the drum potential has been corrected 10 or more times but it does not converge.
Solution: Clean the DPSB (drum potential sensor board), check its installation state, and re-try the auto drum potential adjustment. Please refer to pageS
1-54, 1-55, and 1-56 of the current di750 service manual.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
40
Di750
Description
Part number for the Di750 exit tray.
Solution
It is 4014-1771-01.
Description
The Di750 repeatedly jams when printing envelopes. What can be done to correct this?
Solution
Envelope printing is not within the specifications of this machine.
Description
The web motor M16 may fail to turn properly in the Di750's fusing section. Paper is jamming at the fusing roller during the copy process.
Solution
Cause: This occurs because the gripping force between the magnet ring and the drive shaft of the web motor 01 may become weak due to heat expansion.
Solution: To correct this issue, the web motor M16 has been enhanced so that the holding force between the Magnet and the Drive shaft is increased. The lot
number appearing on the motor can be used to identify the enhanced web motor. Please see bulletin 3753 for details.
Description
Void areas still remain afterI changing the setting for the transfer HV in the process adjustments.It did seem to reduce the void areas, but not eliminate them.
Is there more detailed info on these adjustments?
Solution
SOLUTION: Make sure the drum and developer are under 500K copies. If the count is near 500K you should consider replacing the drum and developer.
Check the drum ground and the coronas, check the corona housings and make sure they are clean. Check the various filters in the copier and make sure they
are clean and moving air properly within the copier.
Some adjustments can be done to customize charge and transfer using the "User Specified Paper Setting" located on page 1-58 of the Di750 Service Manual
. To use the settings after adjusting, enter the key operator mode and select "6-Paper Type Setting". Choose "User" from the listed paper types. This will apply
the settings made in service mode just to the trays with the "User" paper type selected. Do not make adjustments through the "High Voltage Adjustments."
If the above adjustments fail to minimize the problem, try removing the middle separation corona wire. This usually helps because the paper stays charged a
little longer and usually helps with trail edge voids. However, this increases the chance of jamming and possible pick off finger marks.
Description
"Front door open indication" that will not clear even though the front door is opened and closed.
Solution
Check both front door interlocks. Check the 24 VDC from DCPS2 through the interlocks. If not present replace the DCPS2. The part number for the power
supply is 4014-2329-01 as indicated by the Di750 parts manual page 127, Figure 64, index 02.
Description
Starter and other supplies.
Solution
The Di750 takes 1 bag of starter. Click here for a list of Di750 supplies.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded
for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL
http://www.adobe.com/products/acrobat/readstep2.html]]
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
41
Di750
Solution ID TAUS0625353EN* Solution Usage 0
Description
Part number for the Di750 PM kit.
Solution
Di750 Preventive Maintenance Kit (p/n 4014-3317-01). It is a 500K kit which supplies parts for this major maintenance cycle.
Notes:
1. Please see bulletin 3975 for details.
2. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Paper jams in the finisher between the finisher and hole punch unit.
Solution
CAUSE: The sensors are not adjusted properly.
SOLUTION: Verify the sensors in the PK-1 are all clean. Adjust the sensor voltage for each sensor by turning VR1-VR5 on the PUCB (Punch Unit Control
Unit) until the appropriate LED1-LED5 just turns on. This adjustment needs to be done with clean, unblocked sensors "No Paper Present."
Description
Are the same upper and lower fuser rollers used on Di750 and Di850? Is the drum the same for both?
Solution
The lower fuser roller is different (Di850: p/n 4027-1351-01; Di750: p/n 3031-01).
The upper fuser roller is different (Di850: p/n 4027-1431-01; Di750: p/n 4014-3015-01).
The drum is different. For the Di850 it is Photoconductor 802 (Yield 750K/pc) p/n 4027-0291-01.
The Di850 PM Parts Kit (Yield 500K/Set) is p/n 4027-3001-01.
Description
How to re-set the RAM pack to restore factory defaults.
Solution
Perform the following:
1. Set DIP SW 31-0 to "OFF" (in the "25" mode) to enable this adjustment.
2. Re-set the RAM pack using the 47 mode output check 92. This should restore factory defaults.
3. Set DIP SW 31-0 back to "ON" to prevent this adjustment from being executed accidentally.
Note: If this procedure fails to correct the problem, replace the RAM pack.
Description
The Pi7500 LCD screen displays the message "Copier Connection Failure - Reboot 75BW_M Alert." Printing is not possible and sending pages from the
Pi7500 is not possible. The problem is erratic and occurs primarily during long runs. The problem can usually be resolved temporarily by re-booting Di750 and
Pi7500.
Solution
CAUSE: Problem with the ICB (Image Control Board).
Description
Copies are over toned, have background, and intermittent SC46-08 codes are displayed. The copier has been cleaned and developer reinstalled, but the code
and poor copy quality persist.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
42
Di750
Solution
CAUSE: Defective print head assembly.
Description
Soft switch settings list for the Di750.
Solution
SOLUTION: The adjustment section of the Field Service Manual has the soft switch settings and their functions. (See the "25" mode, beginning on page
1-7.)
Description
Paper is jamming at the copier paper exit section, the PK-1, PK-3, and ZK-2 paper entrance section when making copies.
Solution
CAUSE:
Dirty or mis-adjusted paper edge sensors in the PK-1, PK-3, and ZK-2.
SOLUTION:
Clean and adjust the paper edge sensors in the PK-1, PK-3 and ZK-2. Please follow the procedure in bulletin 4014 to correct this.
Description
How to change or delete destination names for scan jobs.
Solution
To add or delete one touch keys, perform the following:
1. Enter the Key Operator Mode
2. Go to # 19 [Scanner transmission settings]
3. Select e-mail, HDD, or FTP.
4. Select the key for the name to be changed or deleted.
a. To change the name, touch the appropriate key, and then touch [Change]. Continue with step 5.
b. To delete the name, touch the appropriate key, and then touch [Delete]. Skip to step 6.
5. Type in the recipient information into each input screen. Touch the key on the left to select the information, and then touch the character keys on the right
to type in the information.
6. Touch [OK]. The Scan transmission setting screen appears again.
7. Touch [RETURN] on the Scan transmission setting screen to return to the Key Operator mode menu screen.
Notes:
a. Please refer to page 18 the Pi6500e Scanner Mode User Manual for the step-by-step procedure.
b. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Item numbers for Parts or Service Manuals.
Solution
Please refer to this publications list .
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
* Trademark ownership information
Description
J32-11 which cannot be reset.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
43
Di750
Solution
CAUSE: The wiring harness of the vertical transport section (right side) is pinched by the lower right side cover.
SOLUTION: Repair potential damage to the wiring harness; route the harness so there is no contact with the lower right side cover when installed. If an LCT
is mounted, ensure the LCT is not pinching the wiring. If the J32-11 code cannot be reset after the wiring harness is repaired, replace the Print Controller
Board (PRCB - p/n 4014-3033-01).
Description
The printer LED on the control panel will not light up. The printer information screen is not available.
Solution
CAUSE: Incorrect soft switch setting.
SOLUTION: Change soft switch 23, bit 4 to on (1) to activate the printer LED on the control panel. Refer to bulletin 3061 for additional soft switch setting
information.
Description
Staple cartridges do not snap into place properly.
Solution
CAUSE: The cardboard holder has been redesigned and the refill does not lock into the cartridge correctly in the staple unit. There is a notch that was not
previously cut in the cardboard, preventing the refill from travelling far enough into the cartridge to lock properly.
SOLUTION: Currently our inventory of staple cartridges (4448-121) are those with the notch. Please replace any cartridges without the notch by reordering
them.
Description
What is service mode 18?
Solution
Service mode 18 is a mode used only during the manufacture of the copier and not used for normal service. Please make sure soft switch 30-0 is set to "OFF"
to disable the "18" mode.
Description
Developer "dusting" on copies and in the image transfer area.
Solution
CAUSE:
The pre-charge erase lamp is turning on. There is no failure code for this lamp. The PRCB may not be turning on the lamp.
SOLUTION:
Check the lamp and associated wiring may be faulty.
Description
What are the specifications of the hard disk for the main body? Can it be replaced with an "off-the-shelf" HDD?
Solution
The main body HDD is a standard drive but it has proprietary formatting. If a replacement is required the drive must be purchased for the specific machine in
which it will be installed.
Description
Is there an option that will give the Di750 or Di850 the capability of 2-hole punching ?
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
44
Di750
Solution
There is no 2-hole punch option available for the Di750/ 850.
Description
Jam code J73-15 service code is displayed.
Solution
CAUSE: The J73-15 code indicates a paper jam& in the punch unit. One of the paper edge sensors on the edge sensor board, PS1 (passage sensor) or PS8
(exit sensor) is blocked when the copier is in an idle state.
SOLUTION: Use the 47 service mode to verify the operation of these sensors. Also make sure the paper edge sensor is clean and check the adjustment of
the edge sensor board.
Note: There are five variable resistors and five LED's on the PK-1 control board used to adjust the edge sensor board. To adjust them turn the variable
resistors located on the PK-1 control board counter clockwise until the LED on the same board goes out and then turn the variable resistor clockwise until the
LED just lights. Then continue to turn the LED clockwise 1/2 of a tick mark further. (Tick marks are indicated on the face of the variable resistor.) Be sure to
adjust all five sensors. Replace the paper edge sensor board if any of the edge sensors can not be adjusted.
Link
Link
Description
The Di750/Di850 display shows "scanning" and the exposure lamp is on. No input to the machine is possible. The machine has to be shut off and restarted to
clear the condition. No error codes are displayed.
Solution
CAUSE: Incorrect firmware version, poor connection or defective SCDB (Scanner Drive Board).
SOLUTION: Make sure the firmware has been upgraded in the copier and all of the connections have been checked. Check the SCDB (Scanner Drive Board)
for cold solder joints or loose connections. Replace the SCDB if the problem persists.
Description
Copies tend to curl up toward the drum and jam between the drum and fuser.
Solution
CAUSE: One of the transfer/separation corona wires could be broken. The broken wire may be due to a broken spring post.
SOLUTION: If the spring post is broken, the T/S corona unit will need to be replaced.
Description
Can meter readings be captured electronically? If so, which machines are supported and how does it work?
Solution
PageScope* Net Care records information for each device on the network, including total print count, error history, and paper jams. Records are kept for a
one-year period. The data can be displayed as a graph, providing a clear picture of the past performance and use pattern for each device. This log history is
automatically recorded when PageScope Net Care is installed.
Notes:
1. Please refer to the following web page for information on the record keeping function of PageScope Net Care:
[[http://www.pagescope.minolta.com/us/products/products/psnc/function5.html| URL
http://www.pagescope.minolta.com/us/products/products/psnc/function5.html]]
2. Compatibility with PageScope NetCare is listed in the compatibility chart linked below:
http://techweb.konicabt.com/tpm/mfiles/compatibility_chart_PageScopev2.pdf
Description
Crossover cable length restrictions for tandem operation. How to set the TCP/IP* address for the copier(s).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
45
Di750
Solution
Tandem operation requires the correct firmware and a crossover cable of less than 100 feet in length. The two machines must be configured the same way
and have the same firmware. Please see bulletin 3205 for additional details.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to set mixed original detecting as the default setting.
Solution
To set the machine's default to mixed originals, perform the following steps:
1. Program Job 30 to include mixed original detecting.
2. Press the [help] button on the control panel.
3. Enter Key Operator mode.
4. On the second screen in the Key Operator Mode: Press [Memory switch.]
5. Set switch 2 (Panel Reset Function) to [Initial Setting.]
6. Set switch 4 (Program memory auto recall (30)) to [On.]
Description
Parts Manual Update - Cover
Solution
See Bulletin Number 4945 .
Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to set TIFF* as the default when scanning to E-Mail, FTP, or HDD.
Solution
There is no way to set the default to TIFF when scanning to E-Mail or FTP. However, when scanning to HDD, it is possible to limit scanning to TIFF only by
setting soft switch 25-0 to OFF. When 25-0 is set to ON, both TIFF and PDF formats are available, with PDF as the default.
Description
One of the paper drawers, the EDH, folding, stapling, page insertion, HDD, or hole punching is not functioning. The component or function is grayed out on
the machine's LCD.
Solution
Check soft switch 18, bits 0 through 7, and soft switch 19, bits 4 and 5 (in the "25" mode). These bits are used by the copier for faulty parts isolation. If a
service code or jam is generated repeatedly the copier will automatically toggle one of these bits to a "1" and disable that section, isolating it from the rest of
the machine's functions.
The following components can be disabled this way through the switches shown below:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
46
Di750
Description
The Di750 displays an SC42-04 code.
Solution
The cooling fan motor and driver board have been replaced as indicated in the Service Manual, with no resolution to the problem.
Check for 24 VDC at the fan motors. If no voltage is present check for an open fuse on Power Supply # 2. Replace it.
If no change replace Power Supply # 2.
Description
C46-14 error message occurs when using the cover inserter "A" option.
Solution
The recommendation from the Di750 Service Manual have been tried, including the replacement of all of the control boards for the copier and accessories
without any change.
Check the installation of the cover inserter "A" option. If any of the wiring harnesses are not set properly in their wire harnesses, problems due to electrical
noise may be generated. Check the wire harness for the top cover. If the wire harness is not set properly, it can contact the PS12 solenoid. The noise from
this solenoid causes the problem.
Description
The Di750 displays an SC56-01 error message. It is not listed in service manual.
Solution
This problem code is corrected by resetting connectors on the printer control board.
Description
How many bags of developer are added at start up?
Solution
One bag of developer is used during start up for this copier.
Description
The fuser section is not turning ON, and the paper cassettes in the copier are all reading metric paper sizes. An SC36-03 error message would display over
time. The PRCB board was replaced, the fuser section was replaced with a new one, and DCPS 1 and 2 were also replaced. Nothing seems to resolve this
problem.
Solution
Replace the front door interlock. If there is no fuser operation, or erratic/false copier operation, the interlocks should be replaced.
Description
The PrintLink075m and Di750 lock up when trying to print from MicroPress after making a copy.
Solution
Change the Timer that prohibits the Printer setting to OFF. See service bulletin 3582 for the detailed procedure.
Link
Description
J72-21 and J72-29 paper jams are indicated. Incorrect "Finisher Working" message is displayed on the copier.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
47
Di750
Solution
CAUSE: PK-1 firmware bug. The firmware version has changed from version 10 to version 11.
SOLUTION: Please refer to Bulletin 3589 and upgrade the firmware in your PK-1 by installing a new EPROM. Please make sure that the copier and finisher
both have the current firmware installed prior to upgrading the EPROM in the PK-1. Please see Bulletin 3061f and Bulletin 3430b for additional
information on the firmware.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Toner is not fusing.
Solution
PROBABLE CAUSES:
1. Incorrect paper specifications or copier setup.
Check that, if thick paper is being used, it is within the specification of the copier and make sure that the paper cassette containing this paper is iconfigured for
"Thick Paper". Charge characteristics are changed along with paper timing. Copies are fed slower to compensate for the additional thickness of the paper.
Also make sure the thick paper is not reprinted or coated. This, too, may affect fusing of the image.
4. Proper voltage at the ACDB (AC Driver Board) is not being supplied to the lamps.
This is checked at CN440 and CN442. Please refer to the schematic diagrams and Service Manual on the adjustments and required voltage readings for
the fuser.
Description
Display indicates "operation in progress."
Solution
CAUSE: The "operation in progress" indication means the machine is still initializing on power-up.
SOLUTION: Move the scanner unit out of home position, and re-start the machine. Check to see if you get any service codes (such as a scanner failure
code). Reconnect the connectors on the scanner control board. Pay special attention to CN-620.
Description
J 92-02 jam codes are displayed intermittently, with copies stalling at the ADU reverse roller. M7 (reverse motor) looks like it binds when it reverses.
Solution
CAUSE: This jam code is generated when the timing of the paper passing PS58 is not properly detected. The issue can be caused by a mechanical problem
or a sensor problem.
SOLUTION:
Attempt to troubleshoot this issue first by running the copier in the paper feed test mode/paperless mode. Please see page 1-72 in the service manual for
additional information on running this test. The mode passes paper without using the paper sensors. If jamming issue continues problem is mechanical. If
issue stops, the problem is the sensor. Check the registration and loop adjustments. These adjustments are very critical. MC1 (the second paper feed clutch)
can also cause this issue. It can be tested in the 47 mode output test 25. Check that clutch engages solidly. Turn the roller manually when engaged to check
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
48
Di750
whether it drives roller solidly. MC1 and MC2 are interchangable. Switch them and see if the symptoms change. If they do replace the clutches.
Note: The following components can also cause this jam code: M7 motor, ADU reverse roller, ADU Idler roller bushings, gear on end of reverse roller shaft,
ADU board, PS58 (ADU reverse sensor).
Description
Current ISW (In-System Writer) utility, Di750.
Solution
The ISW utility is discussed in Service Bulletin 4488A . Please see Service Bulletin 4488 for further instructions. For additional details, refer to the ISW
Service Manual .
Please see bulletin 3104 which provides step-by-step instructions on the ISW (In-System Writer) Flash ROM upgrading procedure. For additional details,
refer to the ISW Service Manual . The current version of ISW is described in bulletin 4488A .
Notes:
1. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
2. Click on the blue-highlighted links within the PDF(s) to view additional details.
3. To open the ZIP file(s), WinZip* must be installed. WinZip can be downloaded from the [[WinZip website| URL http://www.winzip.com/ddchomea.htm]].
4. The WinZip file(s) should have the extension changed from ZIP to EXE. When renamed, the files are self-extracting.
5. The most recent ISW Trns tool can also be downloaded from the [[Konica Minolta FTP site| URL ftp://kbtdigital:kx15@ftp.konicabt.com]].
Description
SC77-36. This code is not listed in the manual.
Solution
CAUSE: The service code has to do with the TMG-1. PS112 (the pusher sensor) is not activated when M107 (the pusher motor) in the TMG-1 is energized.
SOLUTION: Check the sensor to make sure it is working properly. If the sensor does not change logical states when blocked and unblocked, it should be
replaced. If the sensor checks out to be working properly, the motor drive board should be replaced. The drive board is called the TUDB (TU Drive Board).
Please see the Additional Information for Di750 PK-1 Service Manual page 4-59 for additional information on this code. The TUDB can be damaged if the
trimmed booklets jam in the TMG-1. If this is happening check that the TM-G is installed properly. If the TMG is not properly mounted to the finisher, jamming
and booklet misalignment can be generated which may damage other components.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to set mixed original mode to be the default mode at power up.
Solution
Setting mixed original mode for the Di750 is not directly supported as a default start-up setting. However, there is a workaround that will allow this. To set
mixed original mode to be the default mode at power up, perform the following:
1. Refer to page 10-1 of the Di750 Operators Manual and program memory location number "30" with the machine configuration desired on start-up. Make
sure that Mixed Original mode is selected (and add any other feature that you would like to have active on start-up).
2. Go to the Key Operator mode/memory switch settings described on page 14-40 of the Operators Manual. Make sure switch "02-panel reset function" is set
to "initial setting".
3. Make sure switch "04-program memory auto recall (30)" is set to "ON". Now when the panel reset key is pressed or the auto reset timing is engaged, the
copier will automatically recall the machine settings saved in program job 30.
Description
J72-34 service code error. Paper is jamming in the trimmer TNG-1 just as it is about to exit the machine.
Solution
CAUSE: his is a jam code for the TMG-1.
SOLUTION: Information on the code can be found on page 4-31 of the "Additional Information and Corrections for the Di750 and EDH-2" . The code means
that PS108 the conveyance paper feed sensor is not being activated even after M101 the conveyance feed motor is turned on. Please check the flag on
sensor PS108 and make sure that the sensor is functioning properly. Please see Page 2-2 in the C-305/C-305L TMG-1 options service manual for the exact
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
49
Di750
location of this sensor. Also please see page 19 of the TMG-1 parts manual for a breakdown of the sensor and its mechanical flag.
Description
PROBLEM: 11 x 17 copies are buckling, mostly when making duplex copies.
Solution
PROBABLE CAUSES:
1. Play in the fuser section. Check the play by turning the fuser knob slightly forward and reverse while holding/preventing the fuser drive from turning. If there
is play in the drive replace the worn gears. Check also to see if the insulating sleeve bushings (part number 4014-3007-01) are worn.
2. The ADU paper reverse/exit roller 1 (part number 4027-1286-01), ADU paper reverse/exit roller 2 (part number 4027-1343-01), or ADU paper reverse/exit
roller 3 (part number 4027-1341-01) is worn. Clean and replace rollers if needed.
3. The ADU horizontal conveyance roller 1 (part number 4014-2050-01), or ADU horizontal conveyance roller 2 (4014-2050-01) are worn. Clean or replace the
rollers if needed.
4. Components out of adjustment. Check all of the paper feed adjustments for the copier. Please refer to pages 1-63 and 1-65 in the adjustment section of
the service manual.
5. Problems with MC1 and MC2 (in the ADU section). Turn these clutches on in the 47 mode. Make sure they engage and check their holding force by
turning the appropriate feed roller. When problems are generated in the turn-around section MC1 and/or MC2 are usually at fault. Replace MC1 and MC2
together, since the wear on both are generally the same. Please also see service bulletin 3549 , which covers some very critical checks for remedying feed
issues in the ADU. Please also inspect, clean, and check (in 47 mode) all sensors in the turn-around section. Make sure rollers have been cleaned.
6. Improperly operating one-way gear. The one-way gear on the turn-over section should also be cleaned and the solenoid for the switch-over gate should be
adjusted.
7. Outdated firmware. Also make sure the flash ROM in the copier is all up to date.
8. Other worn rollers. Check all rollers (especially part # 4014-2070-01 and 4014-2062-01) and replace if necessary.
Description
In the Installation Procedure for the FN-104/FN4 that came with equipment contains a list of items called "Accessory Parts". What is the part number for item
#2 which is called "main body installation plate/upper."
Solution
The part number for the plate called out as item #2 in the bulletin is 4014-2802-1
Please see service bulletin 3455 for information on parts that do not appear in the options parts manual. Included in this document are the part numbers for
mounting hardware that is included with the FN4/FN104.
Link
Description
FN104, SC77-01.
Solution
CAUSE: The finisher shift unit is not reaching the shift position or home position within the specified time.
SOLUTION: Problems with M2 or PS18 are possible causes. Also check the FNS CB (FNS control board). Check DIPswitch 18 to make sure that bits 0
through 7 are all set to O (if these soft switch settings are not correct, 77-01 will be indicated). Replace any failed parts.
Description
After upgrading to Microsoft* Windows 2000 Pro, the ISW utility completes the loading very quickly and then the machine errors out or the computer times out.
Error 41 is sometimes indicated.
Solution
CAUSE: Older versions of the ISW utility did not support Windows 2000 and Windows XP.
SOLUTION: Please use the latest version of ISW . Also make sure that the computer parallel port is not in ECP mode. Set it to "normal" or "bi-directional"
according to the PC instructions. Refer to the
ISW Instructions for additional detail.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
50
Di750
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to change the default scanning resolution from 400 DPI to another setting.
Solution
The default resolution can be changed by soft switch 19, as follows:
Description
What is the maximum number of one-touch buttons that can be created for scanning?
Solution
For scan to e-mail, up to 96 one-touch buttons can be set up.
Description
The part number for the C-305 clutch in the manual is wrong. The number 4014-2290-01 is a clutch with a straight gear on it; the clutch for the C-305 has a
helical gear on the end. What is the part number for the clutch with the helical gear?
Solution
Please see service bulletin 3393. The part number for the new style gear as indicated in the bulletin is 4014-2503-01.
Link
Description
Part number for the interface kit to connect a Pi7500 to a Di750.
Solution
SOLUTION: The video interface board (VIF) is not available by itself. Please order I/F Kit L, item number 4691-101.
Description
Part number availability for the mixing/auger rollers in the developer unit. The bushings have been replaced, but the shaft is worn and developer is leaking.
Solution
SOLUTION: There is not a part number available for the auger rollers. Please replace the developer assembly as a complete unit (4014-3025-01). To prevent
the developer unit from having to be replaced, please make sure to replace the bushings as soon as leaking is detected. If not replaced, the abrasive
characteristics of the developer will eventually damage the shafts. The bushings are not maintenance items and are replaced as needed. Please inspect them
during every service call as part of your minimum call procedure.
Description
Paper jams between the machine and PK-3/PK-7 or ZK-2/ZK-3. The machine sometimes does not stop immediately. A J 72-45 is indicated.
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
51
Di750
CAUSE:
Outdated firmware for the punch and z-fold units.
SOLUTION:
Please upgrade the punch unit firmware in the PK-1/PK-3/PK-7 by installing a new EPROM. Please refer to bulletin 3589B .
Please upgrade the z-fold unit firmware in the ZK-2/ZK-3 by installting a new EPROM. Please refer to bulletin 4526A .
If the firmware updates do not resolve the issue, please look for mechanical problems with guides and rollers.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
No power or intermittent loss of power.
Solution
CAUSE: The wiring harness of the vertical transport section (right side) is pinched by the lower right side cover.
SOLUTION: Repair or insulate potential damage to the wiring harness and route the harness so there is no contact with the lower right side cover when it is
installed. If an LCT is mounted, ensure the LCT is not pinching the wiring.
Description
What is the part number of the fuser drive gear for the Di750? It is shown in the parts manual but does not have a part number listed.
Solution
The part number of the gear is 4014-2521-01. Refer to service bulletin 3334 for details on a design change to this area of the copier to eliminate damage to
the gear.
Link
Description
SC93-06 at power up.
Solution
CAUSE: This code indicates a problem with the ADU and is usually related to a short in one of the solenoids, clutches, or motors. As a result, one or more of
the fuses on the ADU Board will open. These fuses (called ICP, "Integrated Circuit Protectors") are not replaceable.
SOLUTION: Check the ICP circuit protectors for continuity. If one is found to be open, inspect the wiring harness, solenoids, fans, and motors in the ADU
section for short circuits. Replace the ADUDB (p/n 4014-3251-01) if no shorted components are found.
Description
Is it possible to scan to FTP from the Di750 copier with a Pi7500?
Solution
Sorry, but scan to FTP is not supported on the Pi5500, Pi6500Pro, or Pi7500.
Description
How to access the machine's features by using web-based utilities while connected through the copier's RJ45 port.
Solution
First an IP address must be entered in the copier. This is done from the copier control panel by going to Key Operator Mode / System Initial Settings / IP
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
52
Di750
Address Setting. (If this setting is grayed out, turn on soft switch setting 22-0.)
After making the settings cycle the copier off then back on. By entering the IP address into the web browser of any PC on the connected network the copier
based management utilities can be accessed.
Please refer to Web Utilities documentation for details.
Note:
To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to disable the touch panel calibration adjustment for end users.
Solution
SOLUTION: This can be done by requiring a password to enter the key operator mode. This can be done in the 25 service mode. Go to the menu selection
for Password Setting and enter a four-digit password to restrict access to the key operator mode.
Description
The punch kit (PK) is not recognized by the copier.
Solution
CAUSE:
The fault isolation switch has been activated.
SOLUTION:
Please check soft switch 19, bit 5. This should be off (0). Also check to make sure the correct firmware has been installed in the machine.
Description
The machine is jamming in the finisher when stapling two sheets. It seems to function properly otherwise. After turning on the jam codes (by changing soft
switch 11, bit 7 to on), J 72-18 and J 72-19 are displayed.
Solution
CAUSE: This is related to a problem in the stacker conveyance section.
SOLUTION: A change has been made to the plate springs. Please refer to Bulletin 4395 for details.
Description
"Now Uploading Data" message.
Solution
CAUSE: Outdated firmware/system software.
SOLUTION: Update the copier/printer firmware and the controller system software and ensure that patch files are installed. The Di750 firmware is available
on the [[Konica Minolta FTP site| URL ftp://kbtdigital:kx15@ftp.konicabt.com]]. Please see bulletin 4402 for the patch files.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Printing on tab paper stock with a Di551, Di650, or Di750 copier.
Solution
SOLUTION: The Pi6500e, Pi6500Pro, and Pi7500 controllers do not support this function. It is possible to print a tab job from a MicroPress server.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
53
Di750
Solution ID TAUS0637076EN* Solution Usage 0
Description
Service code SC23-02 is displayed at power up.
Solution
CAUSE: Defective or mis-adjusted front door interlock switches.
SOLUTION: Please check the front door interlock switches. The part number is 4014-1741-01 and the quantity is 2.
Description
Part numbers of the castors for the FN-4/ FN-104?
Solution
The part number for the front castor is 4594-2021-01 and for the rear castor the number is 4594-2016-01.
Description
The FN-4/FN-104/FN-7 does not crimp staples properly in the diagonal staple position.
Solution
CAUSE: Failure of stapler to lock into home position. When the rear stapler swings out and back it should lock in at its home position. Failure to lock in
home position when it swings out to staple is usually caused by a worn holder, pressure spring, and locking pin (metal ball) that hold the bottom of the stapler
while it swings.
Note: When finished replacing parts, perform the stapler clinch adjustment. If adjustment still fails to provide properly clinched staples replace the stapler and
clinch assembly (part number 4377-1034-01).
Description
What is the part number for the handle that is labeled 10a in the exit side of ADU?
Solution
Please see bulletin 3781.
Link
Description
How to get a list of soft switches that have been changed from their original values.
Solution
This can be done by printing the management list of current values and comparing them against the default settings shown in the Service Manual. However,
there is an easier way to compare current settings with the defaults:
Description
SC35-01 is displayed on the machine.The components in the fuser have all been checked and are good.
Solution
CAUSE: Damaged fuser connector.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
54
Di750
SOLUTION: Inspect the blue connector on the rear of the fuser and confirm that none of the pins have been damaged. If one or more of the pins have been
damaged, please refer to Bulletin 3759 to replace the connector.
Description
SC50-05.
Solution
CAUSE: SC50-05 indicates communication problems between the PRCB (Printer Control Board) and the drive boards (SCDB, ACDB, ADUSDB, and PMDB).
SOLUTION: Check and re-seat the connections on PRCB and the drive boards first. If the issue can not resolved by re-seating the connectors, replace the
PRCB. If the issue continues, observe the copier and note when the SC50-05 code is generated. Each of the drive boards performs a specific function.
Noting the timing of the failure, will help to isolate the drive board(s) that may need replacing. The most common cause of this issue is poor connection(s)
(loose or improperly connected wire harnesses) especially if the code is intermittent.
Description
Jam code 72-25 is displayed.
Solution
PROBABLE CAUSES:
1. Worn folding rollers. Replace the folding rollers.
2. Failure of the folding exit sensor. Replace the folding exit sensor .
Description
J32-03 jam codes are frequently displayed. The paper is sometimes found right after the paper exits the fuser or leading into the ADU section of the copier.
Solution
CAUSE: The pin groove of the ADU paper exit/reverse motor (M5) is worn due to repeated rotation/reverse operation.
SOLUTION: To resolve this issue, replace the ADU drive motor. Note: The pin and gear are included with the new motor.
Description
How to set the default to TIFF* when scanning. TIFF should be the only selection available.
Solution
There is only one way to change the TIFF and PDF settings for scan, and that is with a software DIPSW setting in the service mode. The DIPSW available
that effects TIFF and PDF settings is 25-0. When set to 0, TIFF is the only available selection for scanning to HDD. When set to 1, both TIFF and PDF
selections are available. It is not possible to set TIFF as the only default for all other scanning modes (Scan to FTP & Scan to E-mail). Only the scan to HDD
mode has this function.
Description
Recurring copy quality issues, such as poor image density, overall light image quality, and blurred image. In addition, developer and toner intermittently dump
at the magnet roller.
Solution
Please see bulletin 4267 for additional details.
Description
FN104, Spare parts setting of new stapler jig.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
55
Di750
Solution
See TNBT0400002US00 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
FN4, Spare parts setting of new stapler jig.
Solution
See TNBT0400002US00 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
When copying from the platen glass, the start button does not go green. Normal operation when scanning from the document feeder.
Solution
CAUSE: Binding EDH (RADF) sensor.
SOLUTION: Check for a 'sticky' actuator under the front left corner of the document feeder. If necessary, check the sensor in the 47 mode.
Description
How to view current software switch settings and compare to default settings.
Solution
To view current software switch settings and compare to default settings, perform the following:
1. Access the 47 mode.
2. Enter 094 and press the start key. The current software switch settings will be displayed along with the factory defaults for all soft switches.
Note: The current values can also be obtained by printing the management list of current values. They can be compared against the default settings shown
in the Service Manual.
Description
FN104, staple cartridge redesign prevents the stapler vertical positioning adjustment procedure from being performed using the original stapler position jig
(p/n 129XJG011).
Solution
CAUSE: The staple position jig is not compatible with the redesign specifications for the staple cartridge .
SOLUTION: Perform the stapler vertical positioning adjustment procedure using the original-style staple cartridge from the FN121/FN10 finisher or use the
modified stapler position jig (p/n 13QEJG010).
Notes:
1. [[Finisher stapler vertical positioning adjustment|URL http://techweb.konicabt.com/tpm/media/FS_Cartridge.pdf]] procedure.
2. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
FN4, staple cartridge redesign prevents the stapler vertical positioning adjustment procedure from being performed using the original stapler position jig (p/n
129XJG011).
Solution
CAUSE: The staple position jig is not compatible with the redesign specifications for the staple cartridge .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
56
Di750
SOLUTION: Perform the stapler vertical positioning adjustment procedure using the original-style staple cartridge from the FN121/FN10 finisher or use the
modified stapler position jig (p/n 13QEJG010).
Notes:
1. [[Finisher stapler vertical positioning adjustment|URL http://techweb.konicabt.com/tpm/media/FS_Cartridge.pdf]] procedure.
2. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Copier appears dead. There is no display or any LED's lit on the control panel.
Solution
CAUSE:
Bad connection or failure of Image Control Board.
SOLUTION:
Try re-seating the connections to the ICB. If the problem is not resolved, replace the ICB.
Note: Please be sure to move the memory board from the original ICB to the new ICB. The memory board usually does not fail.
Description
DF313, Countermeasure of Double feed prevention and Design change of the LABEL.
Solution
See KOM050204 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
DF317, Countermeasure of Double feed prevention and Design change of the LABEL.
Solution
See KOM050204 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
DF603, Countermeasure of Double feed prevention and Design change of the LABEL.
Solution
See KOM050204 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Slide gear change (shift drive section).
Solution
See KOM050209 for details.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
57
Di750
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Shape change of pressure lever by part sharing with new model.
Solution
See KOM050240 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Thermostat replacement precautions for all models using Faston Terminals.
Solution
CAUSE: Damage to the Faston terminal when replacing the thermostat to the Faston terminal can result in the generation of heat and cause the plastic
insulating material around the terminal to melt.
Description
Information for part number (C-305 (E), C-305L (D))
Solution
See KOM050254 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Correction of Parts Guide Manual - Knob.
Solution
See KOM050287 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
The machine does not automatically switch to the next tray when a paper drawer is emptied. In the Key Operator Mode, "Tray auto select setting" has been
set up to switch trays with a paper-empty condition.
Solution
CAUSE:
Memory switch #9 (Automatic Tray Switching) is turned off.
SOLUTION:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
58
Di750
Please turn on memory switch # 9 for Automatic Tray Switching.
Description
SC 46-08.
Solution
PROBABLE CAUSES:
1. Incorrect firmware.
Re-flash the copier and verify that all of the firmware components are properly indicated.
2. Poor connection between the Image Control Board and Printer Control Board.
Reseat the connection between the ICB and the PRCB.
Description
Problem:
After upgrading the copier's flash ROM (firmware), print jobs being sent to the copier are not being output. Print jobs appear to be sent to the copier, but never
print.
Solution
CAUSE:
Outdated system software in the controller. Version 1.0 is not compatable with the latest copier flash ROM.
SOLUTION:
Upgrade the print controller system software to version 2.0 . The part number for the system software CD is 7660-4685-42.
Description
Jamming in the turnover unit.
Solution
CAUSE: Paper cuts on the black guides within the turnover unit
Description
The warm up time of the copier seems extended, taking between 10 and 15 minutes for the copier to warm up. When making copies of duplexed pages,
some of the pages are missing from the output sets. The copier also intermittently keeps running during a copy cycle and no pages seem to be output. No
service codes or jams are being generated and the only way to reset the copier is to power OFF/ON.
Solution
CAUSE: The ICB (Image Control Board) and ICB Memory Board have failed.
SOLUTION: Replace the ICB (p/n 4014-3034-01) and the ICB Memory Board (p/n 4014-3253-01) as a set.
Note: The new ICB, when installed, requires the Image Control Flash ROM to be installed. Failure to do so will result in a copier that will not power up. The
timer LED on the control panel will also be flashing. Flash the ROMs to the latest revisions found on the [[Konica Minolta FTP site| URL
ftp://kbtdigital:kx15@ftp.konicabt.com]]. If unable to access the 25 mode due to firmware failure, access the non-graphical ISW mode by holding the HELP
and CHECK keys while powering on. If the LCD is blank and the timer LED is flashing the HELP and CHECK mode will not function. At this point, connect
the laptop and send the Image files while the machine is ON and the timer LED is flashing. Then follow the text instructions on the display.
Description
How to enable jam codes.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
59
Di750
Solution
To enable jam codes, please change soft switch 11, bit 7 to ON (using the 25 mode).
Description
"Remove copies from finisher" message.
Solution
CAUSE: Paper jammed in the stapler tray or bent sensor bracket, tray not seated properly.
SOLUTION: Please check for paper jammed in the stapler tray. Also check the bracket angle and mylar for the photosensor and make sure the tray is
seated properly.
Note: Also check the sensor that resets the count when paper is removed.
Description
Are the memory modules for the Di551, Di650, Di750, and Di850 compatible with each other?
Solution
The memory is interchangable among the Di551/650/750/850, with the exception of the 256MB memory module (which is not compatible with the Di750/850).
Description
How to reset ECM after making copies before the next user operates the machine.
Solution
After making copies, hold down the Utility key and press the Clear key to revert to ECM. The next user will then need to enter a code to use the machine.
Description
The machine calls for a PM and then shuts down after 5,000 additional copies.
Solution
CAUSE: The PM counter has reached its life setting and the machine is set to shut down after 5000 additional copies. When the PM count is reached, a
message should be displayed to alert the user, but the machine does not stop automatically unless a soft switch has been set to enable that function.
SOLUTION: To prevent further copying when the count is reached, change soft switch 1, bit 4 to ON. The settings of soft switch 1, bits 5, 6, and 7 determine
how many pages can be printed after reaching the PM count.
Description
SC46-03.
Solution
CAUSE: Failed expansion memory, ICB or ICB connections.
SOLUTION: Remove any installed expansion memory; check connections to ICB. If problem persists, replace the ICB.
Description
The hard disk drive has been installed in the copier, but it is not recognized. When checking in the 47 mode (code 099, multi-mode 1) the HDD capacity
should be shown, but dashes are displayed.
Solution
CAUSE: Incorrect software dipswitch setting.
SOLUTION: Please check soft switch 2, bit 0. It should be ON (1) to enable the hard disk. Also check soft switch 18, bit 7, which should be OFF (0).
Note: This applies to the copier's hard disk, not the hard disk in the print controller (if any).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
60
Di750
Description
Function of ECM account number 1001.
Solution
Account 1001 can be used to count copies from a print controller. When software switch 23, bit 1 is ON (1) jobs from the controller are not printed unless a
valid account number is sent with the print job. This is done in Printer Properties at the PC. If software switch 23, bit 1 is OFF (0) all print jobs will be printed
(even without an account number) and these jobs will be counted in account 1001.
Description
A mistake was made while adjusting the control panel LCD. Now LCD touchscreen does not respond to touch.
Solution
CAUSE: Adjustment out of range.
SOLUTION: Since the LCD touch panel does not respond, the following alternate method must be used to enter the key operator's mode:
1. Hold the Help key while turning the machine on.
2. Enter 10 on the key pad to get into the LCD Touch Panel Adjustment mode.
Note: If this procedure does not work it might be necessary to replace the memory board.
Description
PROBLEM: An "ERROR 2" message is displayed while performing the Auto Maximum Density Adjustment.
Solution
CAUSE: Problem with TCSB (toner control sensor board).
Description
Correction for Parts Guide Manual, Roller.
Solution
See KOM050527 for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
How to determine the amount of total machine memory.
Solution
SOLUTION: Enter the 47 mode, then enter 097. The total machine memory will be diplayed as follows: 64 MB base memory plus any installed upgrade (to a
maximum of 320 MB).
Description
Print jobs go through without a valid ECM password. The copier is using the ECM mode (job accounting). Copies cannot be made unless a valid password is
entered, however print jobs print even when a client sends a job without having entered a password.
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
61
Di750
CAUSE: Soft switch setting.
Notes:
1. If soft switch 23, bit 1 is off (0) all print jobs will be printed (even without an account number) and these jobs will be counted in account 1001.
2. See the Adjustment/25 Mode section of the Field Service Manual for details on soft switch settings.
Description
Explanation of ISW program error codes.
Solution
Please see the ISW section of the Field Service Manual for explanations.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
The EDH on a Di551/Di650 will not feed paper after entering ECM mode. When an original is inserted in the EDH, the ECM password is entered, and the print
key is pressed, the print key stays orange and the EDH will not feed the original.
Solution
CAUSE: This is most often caused by a defective or corrupted memory board.
SOLUTION: Try to initialize the memory board by following the procedure below:
1. Set soft switch 31, bit 0 to "0FF" to allow the memory board to be reset.
2. In the "47" service mode, enter code 92 and press the "START" key.
3. Then enter code 96 and hit the "START" key. This sets the card back to its default settings.
Notes:
a. Remember to return soft switch 31, bit 0 to "ON" to prevent the RAM pack from inadvertent change.
b. If this procedure fails to fix the issue, the memory board should be replaced.
Description
The ISW was interrupted and now the display is unreadable.
Solution
SOLUTION: Enter the "Help-Check" mode to restart the ISW process (Hold down Help and Check keys while turning on power). The ISW utility and
instructions are located in Bulletin 3529a .
Description
Is either the TMG-1 or TMG-2 trimmer compatible with the Di551 or Di650 copier?
Solution
The TMG-1 and TMG-2 trimmers are not compatible with the Di551 and Di650 copiers. The work with the di750 and Di850 models.
Description
How to recall the last job scanned to make extra copies without having to scan originals again and re-program the job.
Solution
To save and then recall a job follow the steps below:
1. Press the [Output Application] key and then the [HDD Store] key.
2. Create a password and user name for your job and then press [OK] to exit the output application mode.
3. Place your originals, select any finishing options press [Start] to make a copy.
4. To recall and print the job again select the [Mode] key until the "Scan" LED is lit.
5. Select the [Image Recall] key and enter the password and user name and the job will be recalled.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
62
Di750
6. Enter the quantity you want and select the [Start] key to make the copies.
Notes:
a. The image recall mode function requires the optional hard disk drive on the Di750.
b. For additional details, see section 11 of the Di750 Operator's Manual
c. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL
http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Staples in the FN4 finisher can not be replenished when they run out. A staple supply message is indicated on the operation panel while the stapler is moving
to the home position. At that time, if an operator opens the finisher door according to the message, the stapler stops at the current position. Therefore, the
operator cannot replenish the staples.
Solution
CAUSE: Updated firmware is needed.
SOLUTION: This issue has been corrected with finisher ROM version 40 and above. The firmware should be upgraded if this problem is encountered. See
Service Bulletin 3061F for information on ordering or downloading the latest finisher ROM.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
Description
SC 56-04 is displayed when connected to *MicroPress version 6.x.
Solution
CAUSE: This indicates a communication problem between the PrintLink and the copier.
SOLUTION: Check the firmware in the PrintLink and check the connections between the PrintLink and the copier.
The PrintLink 075m (for the Di750) must have version 305-000829-60.bin or higher.
Description
The service manual refers to a P function to enter the service modes. Where is the P button located?
Solution
The service manual refers to the Utility key as the P button. To enter the service modes (25, 36, 47, and Key Op modes) hold the Utility key until the display
changes. When "Enter 4-digit password to change mode" appears at the top of the screen, enter 9272 on the numeric key pad and then press the start key.
Description
What are the power requirements for the Di750 copier?
Solution
The power required for the Di750 is 208VAC. The current draw requires a 20A circuit at 60Hz
Termination: NEMA Type 6-20R receptacle (250V AC, 2-pole, 3-wire, grounded).
Note: A dedicated AC line with an isolated ground is strongly recommended. A dedicated line mandates the exclusive use of a circuit where the receptacle
grounding terminal is grounded by an insulated grounding conductor that is isolated from the receptacle (per National Electrical code, article 250-74,
exception no. 4).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
63
Di750
Description
The copier shows four paper drawers on the LCD display; there are actually only three.
Solution
CAUSE: Incorrect soft switch setting.
SOLUTION: Please set soft switch 28, bit 2, to OFF (in the 25 mode) to return to a normal display.
Description
SC21-06 at power up. Also, there is a lead to trail-edge void on the copies.
Solution
CAUSE: The transfer cleaning motor (M18) binding or failed.
SOLUTION: Check the operation of the motor by manually moving the cleaner to its home position. Replace the motor or ADU drive board if there is no drive
after moving the cleaner from the home position.
Description
PM kit availabilitiy.
Solution
SOLUTION: The part number for the PM kir is: 4014-3317-01. This is a 500k kit.
Description
Part number for the FN-4 folding kit.
Solution
The part number of the kit is 4014-0901-01. Please see Service Bulletin 3429 for additional information on the changes made on the FN-4.
Description
Can tandem mode be used to split print jobs (from Fiery controllers) between two copiers?
Solution
Print jobs can't be split between two copiers using Tandem mode. Tandem mode applies to copy jobs only.
Description
An F80-10 error message displays after performing the ISW upgrade on the copier.
Solution
Cause: This error message means that the C1 program was not loaded properly.
Solution:The data should be verified for proper version, and the installation should be done again. See Service Bulletin 3104 for additional information on
set-up. The ISW utility and instructions are available on bulletin 3529a .
Description
Does tandem copy work with a file retrieved from the HDD? What kind of jobs are not compatible with tandem operation?
Solution
If the primary copier is installed with HDD, the image data stored in HDD can be output in tandem mode copy.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
64
Di750
Group, Rotation
Transparency Interleaving
Set Numbering
Watermark Numbering in Stamp.
Please see the Operator's Manual for details. (For the Di850, tandem operation begins on page 7-26.)
Link
Description
The copier is set up with fewer than 1000 users in ECM mode. Data for all accounts can be used and viewed but the print out stops before all are printed.
What can be done to complete the print out of ECM data?
Solution
CAUSE: There are un-used or deleted slots in the list. When the report gets to an open slot the logic determines that that is the end of the list and stops
printing.
SOLUTION: Fill in the empty slots so that there are no un-used accounts before the end of the list.
It is also possible that this is caused by a problem with the RAM pack. Try resetting the RAM pack using the 47 mode output check 93. Remenber DIP SW
31-0 must be set to "OFF" (in the "25" mode) to carry out this adjustment. This should restore factory defaults. If this procedure fails to correct the problem,
replace the RAM pack.
Description
SC50-01 or SC80-02 on start up.
Solution
CAUSE: A communications issue exists between the ICB (Image Control Board) and the PRCB (Printer Control Board).
SOLUTION: Unplug then reseat the ICB and the ICIFB. Unplug and reseat all of the connections to the PRCB to insure the two boards have a solid electrical
connection to each other. If the problem persists, replace the ICIFB (p/n 4014-3248-01 for the 7075/7085 and p/n 4027-1396-01 for the Di750/Di850).
Description
How to set the mechanical counter to click twice when feeding 11x17 paper.
Solution
To set the mechanical counter to count twice for 11x17 paper, access the 25 mode and set DIPSW04-7 to ON.
See page 1-8 in the Di750 Service Manual for additional information.
Description
Is it possible to set the copier so that walk-up users can interrupt a long job without having to wait for the set in progress to finish?
Solution
The machine can be set to allow walk-up users to interrupt a long job, although the default is for the interruption to occur between sets, this can be changed
via a switch setting in Key Operator Mode. Follow the steps listed to make the change to the machine:
1) Press HELP.
2) Select KEY OPERATOR MODE.
3) Select #13 - SOFTWARE SWITCH SETTING.
4) Press the down arrow four times and highlight #31 - AN INTERRUPTION SUSPENDED WAY.
5) Press CHANGE SETTING until it reads "DURING A NUMBER OF COPIES."
6) Press RETURN twice.
This will enable the user to press INTERRUPT and suspend a large job in the middle of a set.
NOTE :
When this switch is enabled, the originals can ONLY be copied from the glass, and the output can ONLY go to the Sub-Tray (with a choice of face-up or
face-down, so as not to confuse the output of the 2 different jobs). The only other manipulation available is to select either 1:1 or 1:2. On the other hand,
"between-set interruption" (default) allows all available finishing and even multiple sets. In either case, once the interruption is done, the INTERRUPT key is
pressed again and the suspended job continues where it left off.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
65
Di750
Additional information:
The user also has the ability to program copy jobs ahead while another job is running. There are 5 "Soft Tabs" on the GUI labelled "RESERVE JOB" (10 on
the Di850), therefore, while one job is printing, up to 4 additional jobs (9 on the Di850) can be programmed ahead. Simply press the tab to begin programming
your job, then press START to scan it into memory. Since these jobs are not interrupting the job in progress, all finishing and job manipulation options are
available. Once one print/copy job ends, the next starts automatically.
Description
The Di750 Intermittently displays F23-01 at power up.
Solution
CAUSE: Failed developing drive motor (M3).
Note: The error code is normally for toner motor 2 (M15) abnormality.
Description
The LCD has vertical lines across the display and the display is also slightly distorted. All of the functions work properly.
Solution
PROBABLE CAUSES:
1. Poor connection. Please check connections (especially CN136-3) and look for pinched wires.
2. Display malfunction. Replace the display.
3. OB1 (Operation Board/1) malfunction. Replace OB1.
4. DCPS (power supply) malfunction. Check the DCPS and replace if necessary.
5. ICB (Image Control Board) malfunction. Re-flash or replace the ICB.
Description
ECM (EKC) password length.
Solution
The number of digits required can be changed in the Key Operator mode. Go to #13, Memory Switch Setting, then ECM Password. The default is 8 digits,
but it can be changed to "under 8 digits" (which sets it to 4 digits). Please see the Operator's Manual for details.
Description
Parallel cable specifications for upgrading the flashROMs of the copier using the ISW utility.
Solution
The parallel cable needed is an Amphenol 36-pin-D-sub 25-pin Centronics*; with a length of less than 2 meters. For additional details, refer to the ISW
Service Manual . The current version of ISW is described in bulletin 4488A .
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
The Di750 displays a J92-03 is displayed while the machine is idle.
Solution
This can be caused by paper dust on and near PS58 (ADU paper reverse sensor).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
66
Di750
Clean PS58 using the following procedure:
Remove the fixing (fusing) unit.
Remove the fixing fan cover by removing 2 screws, be careful not to damage any wiring. The fan will come out with the cover.
Remove the fixing mounting plate by removing 4 screws, be careful as to not damage any wiring.
Clean PS58 and the surrounding area using a blower brush or canned air.
Reassemble using care not to damage any components.
Description
How to disable scanning to the Fiery Pi7500.
Solution
On the Di750, use the 25 mode to change soft switch 23, bit 4 to off (0). This disables scanning to the Pi7500.
Scanned jobs (when scanning to the Fiery hard disk) can also be made inaccessible to unauthorized users by setting a password in WebTools.
Description
The jam counters are not displayed in the "25" mode.
Solution
CAUSE: By default, this view is suppressed to prevent the counters from being reset.
SOLUTION: To view (and reset) the jam counters, turn soft switch 30, bit 1 on (change it to 1).
Description
SC 80-30 is displayed when updating the flash ROM.
Solution
CAUSE: A problem has been encountered with the printer cable.
Description
How to disable auto shut off.
Solution
To change the Auto Low Power/Auto Shutoff settings, perform the following steps:
2. Enter the Key Operator Mode by holding down the Help key and powering the machine ON.
3. Touch the down arrow located in the lower left corner of the screen.
Note: "-----------" indicates no auto shut off. Once selected, the choice of auto shut off will be grayed out. Auto Low Power can not be disabled; it can be set to
a maximum of 240 minutes.
Description
How to copy onto tab stock.
Solution
To run tabs on these machines the latest firmware must be installed. Once that is confirmed, follow these steps:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
67
Di750
1.Load tab stock face down with tabs away from feed rollers.
2. Let the machine know that it has got tabs by pressing the HELP key then select Key Operator.
3. Select #6 "Paper Type - Special Size" then choose the appropriate tray, scroll through paper sizes, and choose Tab.
4. Place tab originals face down on glass platen with tab toward center of glass.
5. Select "Special Originals" then choose Tab - 8.5" x 11" and then choose to pull paper from tray with tabs loaded.
6. Press PRINT.
Description
Part numbers for the staples and cartridges.
Solution
The following finishers use the same staple cartridge (MS-5C), item number 4448-121:
FN-6, FN-112, FN-4, FN-104, and FN-7.
Description
The customer has lost the password they set for the timer mode. Can the password be re-set?
Solution
SOLUTION: Yes. Hold the Utility key until you a prompted to "enter password for mode selection." Enter 9272 and press the start key. Select Key Operator
Mode and then go to Weekly Timer. From that menu, select Timer interrupt password set. You can now change the password for the timer mode.
Description
Please load paper in tray 3" is displayed on operation panel and SC 18-32 is displayed only on data collection, list output.
Solution
CAUSE: An SC 18-32 code is generated when PS22 (tray upper limit sensor 3) which has been OFF, is not turned ON within 10 seconds of upward
movement, started by turning ON of M21 (up drive motor 3). At this time, a trouble detection signal (blown fuse) is detected. The error code is not displayed
on operation panel. It is displayed only on data collection, list output. The messsage "Please load paper in tray 3" is displayed on operation panel because
tray has not completed ascending.
SOLUTION: Depending on checks, replace M21 (up drive motor 3), DCDB (DC drive board), PRCB (printer control board), or PS22 (tray upper limit sensor
3).
Description
The cut position is misaligned during the trim mode.
Solution
CAUSE: The cut position may become misaligned with the combination of TMG-1 and FN-4 with improved folding performance. If the FN-4 with improved
folding performance is used, booklets tend to rebound after hitting the stopper at TMG-1 because the booklets are conveyed with a higher speed than with the
earlier version of the FN-4.
SOLUTION: Upgrade the firmware of the FN-4 to version 45. The timing of stopping booklets has changed so that the booklets do not rebound after hitting
the stopper and cut position for booklets can be correct and consistent. Please refer to Technical Bulletin 3430b for more detail.
Description
FN4, SC77-01.
Solution
CAUSE: The finisher shift unit is not reaching the shift position or home position within the specified time.
SOLUTION: Problems with M2 or PS18 are possible causes. Also check the FNS CB (FNS control board). Check DIPswitch 18 to make sure that bits 0
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
68
Di750
through 7 are all set to O (if these soft switch settings are not correct, 77-01 will be indicated). Replace any failed parts.
Description
Is AS/400* printing supported?
Solution
AS/400 support is available for digital copiers/printers that are connected to controllers which have PCL* emulation. Refer to the the Copier Bulletin #
01-MB-27 for answers to the most common questions about AS/400 printing. The P4Server brochure and specification sheet provide additional
information.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Why is the trimmer TMG-1 not listed in the Available Options area on the Configuration tab in the Printer Properties?
Solution
The trimmer is not supported with the version 1.01 print driver. The following options are supported: FN-4, FN-104, C-305, and cover inserter A.
Description
When printing a document using Free Form, the edge of the master image is cut off. When using portrait-sized paper about 11mm from the right edge of the
master image is cut off. When using landscape-sized paper about 11mm. from the bottom edge of the master image is cut off.
Solution
CAUSE: This issue is caused by a bug in the system software version 2.0 and is found when using the PostScript* emulation and the following operating
systems: Macintosh*, Microsoft* Windows 2000, 95/98, and NT 4.0.
SOLUTION: Install PostScript patch file 1-4Q76U.PS to the print queue of the Pi7500 using Fiery* Downloader or Fiery Web Downloader. Wait 60 seconds
after successfully downloading the patch file to allow sufficient time for the file to be RIPed and installed. The print controller should then be restarted. Print a
controller configuration page and confirm that the patch file has been successfully installed. The patch will appear under a heading labeled "Update
Information." Please see bulletin 4402 for details.
Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Unable to select Tab printing when using the document feeder.
Solution
CAUSE: Early version firmware is installed on the main body.
SOLUTION: The proper firmware versions must be installed to allow this to function properly. See service bulletin reference number 3061f for more
information on the current firmware.
Description
Does Konica Minolta provide support for Equitrac* products?
Solution
For Equitrac technical support information please visit [[http://www.metrics.com/Support/| URL http://www.metrics.com/Support/]] or contact trained Support
Engineers by telephone at 519.885.2458, by fax at 519.746.7931 or via E-mail at support@metrics.com
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
69
Di750
Description
Following a Novell* NDPS or iPrint installation, the Windows* print driver is configured with default settings ONLY on the client workstation.
Solution
CAUSE: Novell NDPS or iPrint drivers are migrated from the Novell server to clients in a non-configured format. This is because the driver is not actually
installed on the Novell server. In the Novell environment, the server simply holds, and then pushes the non-configured driver files to the client. In a Windows
server environment, the Windows driver is installed on the server and can be configured prior to roll out to the clients.
SOLUTION: It is possible to roll-out configured drivers from in a Novell environment. Novell's ZenWorks* allows the Novell administrator to create a snapshot
of a client workstation before and after the driver is installed and configured. This snapshot can then be migrated to the user's workstations resulting in a
configured driver installation.
Using ZenWorks to migrate a configured driver will vary based on Netware version, ZenWorks version, NDPS version and Windows client version. Therefore
step by step instructions to perform this operation are not available. The Novell administrator at the location would be responsible for implementing this
procedure.
[[Third party print driver configuration applications| URL http://www.printerpropertiespro.com]] for Novell are also available. Please consult the vendor(s) for
implementing these solutions.
Description
DF317, Countermeasures for the belt coming off prevention
Solution
See KOM051187.pdf for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
DF-313, Information for parts number (Roller spacer 3).
Solution
See KOM051190.pdf for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Countermeasures for interference prevention (Cover assy).
Solution
See KOM051196.pdf for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Does WinFax Pro10 Software work with AHT OneRip 2?
Solution
A WinFax Pro10 Software Option is available for the OneRip 2 solution. Fax from a KonicaMinolta legacy MFP that previously did not offer fax capabilities.
When connecting multiple printers to the OneRIP 2 server, all connected printers are enabled with faxing. The MFPs do not require a fax board. Working as
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
70
Di750
the Scan to E-mail function, simply insert the fax number in place of an E-mail address, and proceed. The WinFax Pro Option supports the following devices:
Di450/Di550
Di551/Di650, 7155/7165
Di750, 7075
bizhub Di470
bizhub Di5501/Di7210, bizhub Di7255/7272
bizhub Di850, bizhub 7085
bizhub CF2002/CF3102
Description
To achieve parts standardization with the other model, the Electrode vibrating rubber has been modified.
Solution
See KOM051320.pdf for details.
Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]
Description
Toner spilling in the copier. After a developer change machine works properly for 30,000 to 40,000 copies then dumps again.
Solution
CAUSE: The developer is becoming damaged from continuing to run the copier after an out of toner condition. The copier can run 3,000 copies after each
time the door is opened and closed. The developer is damaged if toner is not replaced after the first out of toner indication.
Note: Setting DIPSW1 bits 0 - 7 to "OFF" in the 25 service mode limits the copier to 1,500 copies (instead of 3,000 by default) when an out of toner condition
is detected.
Description
Intermittent black copies with paper wrapping around drum.
Solution
CAUSE: Poor drum ground.
SOLUTION: Clean and service the front and rear drum bearings. Clean only the inner circumference of the bearing and the drum shaft. Use Scotch-Brite* or
emory cloth to clean build-up. Do not lubricate or flush bearing with alcohol. The bearing is packed with conductive grease which is needed for proper
operation. Replace the bearing if does not turn properly or if the bearing appears worn. Make sure the drum shaft coupler is flush against the drum flange
and the notch is flush with the front bearing when reinstalling.
Description
PrintLink 075m Installation Guide.
Solution
Di750 Printlink Guide2
Notes:
1. The document is approximately 4MB.
2. To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
71
Di750
Solution ID TAUS0651004EN* Solution Usage 0
Description
How to clear account number 1001 on the ECM list printout.
Solution
To clear account number 1001 on the ECM list printout, perform the following:
1. Launch Web Utilities.
2. Go to Environment Setup.
3. Then click "EKC Function Setting" and use "ekc" as the user name and the copier's ECM password.
4. Click on EKC data list and scroll to the bottom of the list.
5. Check the box to the right of "Another user account" and select the button labeled "Reset the count of selected item(s)." 6. Click "Apply" twice.
Note: When using ECM without the switch turned on, it counts the copies in account number 1001 on the ECM list printout.
Description
J32-05 exit jam.
Solution
CAUSE: The Pusher Plate and Holder Plate in the trimmer stacker area of the TMG1/TMG2/TU1 can suddenly stop in the middle of a stacking operation.
The MS3 and MS4 (microswitches) in the TMG1/TMG2/TU1 have failed due to oxidation of their contacts. The switches are in series with the power supplied
to M106 (holder motor) and M107 (pusher motor). When the microswitches become oxidized, insufficient current is supplied to the motors causing them to
stop. The failure of the trimmer motors causes all of the finisher options to shut down.
Description
Changes made to copier initial settings (in key op mode) are lost after the panel reset button is pressed. The settings revert to the factory defaults.
Solution
CAUSE: Incorrect memory switch setting.
Description
Part number for the interface kit to connect a Pi7500 to a Di750.
Solution
I/F Kit L (Item #4691-101).
Note: The video interface board (VIF) is not available by itself.
Description
How to check the machine memory (RAM).
Solution
To check the amount of memory installed in the machine, perform the following:
1. Enter the 47 service mode.
2. Enter code 97.
3. Press the Start key. The total memory is displayed.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
72
Di750
Description
What Engines/Firmware is supported with MicroPress* 7.0.0.8 EFGS?
Solution
1. PrintStation 092km with the following firmware version:
IP Control: 70-0000.
Image Control: 20-ABSO
Print Control: 12-0000
Description
SC28-04 displayed at power up.
Solution
CAUSE: Loss of 24VDC to ICP5 on the ADU DB.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
73
Di750
Description
How to make copies exit face down when they are exiting face up. Also,how to make copies exit face up when they are exiting face down.
Solution
To make copies exit face down/face up, perform the following:
1. Enter the Key Op mode.
2. Select Memory switch settings.
3. Select Exit direction.
4. Set to Face Up or Face Down, as desired.
Description
SC46-24 after cleaning the copier.
Solution
CAUSE: The white strip under the slit glass bracket is missing.It is used at start up toperform shading correction.
SOLUTION: Check that the copier has been properly re-assembled. Install/position any missing parts (white strip)and open and shut the front door to clear the
code. If the code does not clear, check the connectors to the ICB (Image Control Board) and re-flash or replace the board (p/n 4396-1278-01)if necessary.
Note : The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Description
SC56-04 on the printer.
Solution
PROBABLE CAUSES:
1. The SC56-04 service code is generated when a new memory board is installed and the copier serial number information is not entered.
Re-enter the serial number after the memory board has been properly installed and reset. The new memory board must be initialized and the serial number
information must be re-entered into the copier. Please refer to attached bulletin 3613 for details.
2. If an optional print controller has been installed, SC56-04 may indicate a communication problem between the print controller and the IFB (Controller
Interface Board) or between the IFB and ICB (Image Control Board).
Re-seat the connectors on the ICB.
3. The code sometimes indicates a communication problem between the operation panel and the ICB. If the copier/printer functions normally, except when
printing from the controller, the problem is most likely related to the Interface Board.
Re-seat the connectors on the ICB and the operation panel. Verify that the copier/printer has current firmware. If a controller is attached, make sure that the
controller power cord is plugged into the power receptacle inside the copier/printer. Please see attached bulletin 3097 for details. If the code persists, reload
the PRCB firmware and the ICB firmware. It is also possible that the ICB (p/n 56QA-9010 ) or IFB (p/n 65AA-9120) may need to be replaced.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
SC21-01 at power up.
Solution
CAUSE: Binding or failed M23 (Charge cleaning motor).
SOLUTION: Remove the Charge corona unit and inspect the gears for binding. Replace M23 (p/n 25AA80090), Charge cleaning gear/1 (p/n 55VA77230),
Charge cleaning gear/2 (p/n 55VA77240) or the Charge corona unit (p/n 56GA-2500) as necessary.
Description
Which scanners are supported for MicroImager™?
Solution
The Scanlink feature which supports the Di650, Di750 and Di850 allows the use of scanning from the copier document feeder onto the hard drive for
processing in the PrintStation™ Manager and MicroImager™.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
74
Di750
Notes :
1. Canon Image Runner™ 8500 and Fujitsu™ (F50) scanner are directly supported by MicroImager™.
2. MicroImager™ requires additional software to be installed.
Description
Are Konica Minolta MFPs compatible with Category 6 cable standard?
Solution
Konica Minolta MFPs are fully compatible with Category 6 cable standard.
Category 6 cable is a cable standard for Gigabit Ethernet and other network protocols that is backward compatible with the Category 5/5e and Category 3
cable standards.
Cat-6 features more stringent specifications for crosstalk and system noise. The cable standard is suitable for 10BASE-T/100BASE-TX and 1000BASE-T
(Gigabit Ethernet) connections and it provides performance of up to 250MHz.
Description
SAP device types availability.
Solution
Refer to attached Marketing Bulletin #06-GB-039 for details.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
Does the Pi7500 support scan to E-mail?
Solution
The Pi7500 does not support scan to E-mail or scan to FTP. Scan to the HDD is available using Fiery® Web Tools.
Description
Intermittent 19-1 jam error code.
Solution
CAUSE: The main charge corona grid is loose.
SOLUTION: Remove the main charge corona and reseat the grid.
Description
J10-1 when feeding from the bypass tray.
Solution
CAUSE: The inner bypass feed driving gear is worn or broken.
Description
Paper size 8.5x11R is recognized as A4R when feeding from the document feeder.
Solution
CAUSE: Incorrect dipswitch setting.
SOLUTION: To adjust the machine to recognize 8.5x11R correctly, perform the following:
1. Enter 25 mode.
2. Select Software DIP SW Setting.
3. Set DIPSW 13-1 to 1 and exit the mode.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
75
Di750
Description
How to perform Print Screens (screen shots) from a Microsoft® Windows OS and Macintosh® OS.
Solution
Please see the attacheddocument for detailed information.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
Unable to print all ECM accounts.
Solution
CAUSE: ECM accounts were deleted and now there are spaces/blanksbetween the ECM accounts.
SOLUTION: Re-program the ECM accounts consecutively and ensure there are no spaces between ECM accounts.
Description
Printing to a Windows Samba shared printer from a Macintosh®.
Solution
Please perfrom the step-by-step procedure mentioned in the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Description
What soft switch controls the faulty part isolation for the ADF?
Solution
To enable and disable the ADF use soft switch 18-4. Setting 18-4 equal to (1) disables the ADF and setting it to(0) enables the ADF.
SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009
76