Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 175 views

    Tec 301 HCS (UAE) : Non Shrink Very High Strength Grout

    Uploaded by

    manikandan4strl
    1. tec 301 HCS is a non-shrink, high strength grout for repairing high strength concrete structures. 2. It can be used for tasks like anchoring rebar, filling voids, concrete jacketing, and bridge bearing applications. 3. The grout has a compressive strength of over 72 MPa at 28 days curing and remains flexible to allow for plastic or fluid consistency during application.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Tec 301 HCS (UAE) : Non Shrink Very High Strength Grout

    Uploaded by

    manikandan4strl
    175 views2 pages
    1. tec 301 HCS is a non-shrink, high strength grout for repairing high strength concrete structures. 2. It can be used for tasks like anchoring rebar, filling voids, concrete jacketing, and bridge bearing applications. 3. The grout has a compressive strength of over 72 MPa at 28 days curing and remains flexible to allow for plastic or fluid consistency during application.

    Original Title

    TDS_webertec_301_HCS-UAE

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. tec 301 HCS is a non-shrink, high strength grout for repairing high strength concrete structures. 2. It can be used for tasks like anchoring rebar, filling voids, concrete jacketing, and bridge bearing applications. 3. The grout has a compressive strength of over 72 MPa at 28 days curing and remains flexible to allow for plastic or fluid consistency during application.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    175 views2 pages

    Tec 301 HCS (UAE) : Non Shrink Very High Strength Grout

    Uploaded by

    manikandan4strl
    1. tec 301 HCS is a non-shrink, high strength grout for repairing high strength concrete structures. 2. It can be used for tasks like anchoring rebar, filling voids, concrete jacketing, and bridge bearing applications. 3. The grout has a compressive strength of over 72 MPa at 28 days curing and remains flexible to allow for plastic or fluid consistency during application.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    tec 301 HCS (UAE) Formerly "Conrep.

    301 HCS" TECHNICAL AND


    REPAIR MORTARS

    Non shrink very high strength grout

    PRODUCT
    tec 301 HCS is a blend of portland cement, special
    admixtures and proprietary aggregates designed to provide
    high flexural and compressive strength performance from
    plastic to fluid consistencies. tec 301 HCS is non-metallic,
    non-shrink, non-gas forming and contains no chlorides or
    aluminum powders. It is specialy used when repair of high
    strength concrete is required.

    SCOPE OF USE
    • Assembly of pre-cast parts made of reinforced or
    pre-stressed concrete
    • Bridge bearing applications
    • Concrete jacketing for slabs, columns, beams and footings
    • Reblocking / restumping / void filling applications
    • Closing or filling around pipes in water tanks / swimming
    pools PACKAGING
    • Pumpablity properties Leb Syria Jordan UAE Qatar Kuwait KSA Oman
    • Anchoring of steel bars - - - 25 kg - - - 25 kg
    • Jointing - - - 50 kg - - - 50 kg
    • Fixing industrial equipment and heavy machinery, mounting
    plates
    • Vertical shoring
    • Void filling operations
    • Excellent shock & vibration resistance CHARACTERISTICS
    Appearance Grey powder
    ADVANTAGES Grain size 0 to 3 mm
    • Non-shrinking Free from chlorides and
    • High strength metallic particles
    • Easy to apply Fresh density 2340 kg/m³
    • Resistant to sea water and sulfates (BS 1881:83)
    • Liquid or plastic consistency Lengthchange 0.062 % @ 28 days
    (ASTM C157-03)
    Pull off stress > 1.5 N/mm² @ 28 days
    (BS 1881 Part 207)

    *COMPRESSIVE STRENGTH
    AGE 1 day 7 days 28 days
    COMPRESSIVE STRENGTH (N/mm²) 32 57 72
    STANDARD BS-EN 196-1 BS-EN 196-1 BS EN 196-1

    *FLEXURAL STRENGTH & TENSILE STRENGTH at 28 days


    AGE 28 days
    FLEXURAL STRENGTH (N/mm²) – BS EN 196 -1 7
    TENSILE STRENGTH (N/mm²) – BS 6319:PART 7: 1985 3.8

    *Results obtained at fluid consistency: 12% water or 6 lit. per 50 kg bag.


    The mechanical carateristics will be higher if the tec 301 HCS is mixed at plastic consistency: 9.5% water or 4.75 lit. per 50 kg bag. In this case,
    the compressive strength can exceed 80 MPa at 28 days.

    1/2 Technical data sheet . Edition: 09.19-A www.middleeast.weber


    tec 301 HCS (UAE) TECHNICAL AND
    REPAIR MORTARS

    APPLICABLE STANDARDS STORAGE


    BS EN 196 Part 1 12 months after manufacturing date in original and non-open
    BS 1881 Part 207 packaging , under cover, in dry condition, away from humidity,
    ASTM C 157-03 protected from extreme temperatures and direct sunlight.
    BS 6319 – Part 7- 1985
    BS 1881: 83 PRECAUTIONS
    ASTM C 1107 Substrate must be sound and resistant. It should be saturated
    with water a few hours prior to installation. Remove all water
    INSTRUCTIONS FOR USE used in wetting support prior to installation of tec 301
    PRODUCT PREPARATION HCS.
    Grout or mortar is obtained by mixing tec 301 HCS with Do not mix with other hydraulic binders.
    clean water. The amount of water used depends on the
    workability required. SAFETY PRECAUTIONS
    Add the powder to the water and mix for 3 minutes. To The product contains cement powders which, when mixed
    ensure a homogeneous and uniform mix, an electric mixer with water, release alkalis that could be harmful to the skin. It
    must be used. is preferable that the application be done in a ventilated
    area, and to wear protective gear for hands, eyes and
    Mixing respiratory system and to avoid breathing of the dust.
    tec WATER (1) VOLUME IN Splashes on the skin should be washed away by cleaning
    301 HCS PLACE with soap and water. In case of contact with eyes, wash
    MORTAR 50 Kg 4.5-5 lit. 26 lit thoroughly with clean water. If swallowed, do not induce
    GROUT 50 Kg 5.5-6 lit. 28 lit. vomiting, in both cases seek medical attention. The product
    (1): Half quantity of water is required for 25 Kg package is non-flammable.
    PRODUCT APPLICATION
    For grouting /jacketing/repair
    DISCLAIMER
    While the company guarantees its products against defective
    tec 301 HCS can be used for thickness up to 10 cm.
    materials, the use and application of these products are
    Existent surface needs to be roughened and cleaned. Ensure
    made without guarantee since the conditions of their application
    damping the surface with water before the application.
    are beyond its control. It is recommended to verify with the
    Thickness above 10 cm can be practiced up to 30 cm in case
    company that the product is suitable for the intended use,
    of epoxy anchoring dowels (rebars) installation in the
    and that this Data Sheet version is the latest one. The company
    existent structure by (pouring) the Pure epoxy (anc 405
    may modify it without prior notice. Technical characteristics
    BFX) into drilled holes in the existent structure, then steel
    are listed for guidance only. For more information, please
    mesh to be connected to Dowels (rebars). Ideal Application
    contact the company’s office in your location.
    temperature is between +5 ºC and 35 ºC

    For Shoring/Soil Nailing Applications NOTE


    tec 301 HCS can be used for grouting the inclined holes The information included on this Technical Data Sheet is the
    in shoring applications. Hole diameter must not exceed 20 sole property of SODAMCO Holding. The unauthorized disclosure,
    cm, depth of hole will be determined by structure engineer. use, dissemination or copying (either whole or partial) of this
    tec 301 HCS is high fluid and non-shrink properties data sheet or any information it contains, is prohibited and
    ensure excellent anchoring/friction with soil/rocks. If the subject to legal pursuit.
    application temperature is higher than 35 ºC, make sure to
    PG:24
    use cool water to keep the mixed grout temperature below
    *Available only in UAE
    30 ºC.

    CURING
    Protect the work against rapid drying from wind, sun and
    excessive heat by using a curing compound like ad
    cure WH or ad cure Y 40 or by covering with properly
    secured plastic sheeting.

    2/2 Technical data sheet . Edition: 09.19-A www.middleeast.weber

    You might also like