Total Station: Lecturers: Berchuk V.Y. Gutareva N.Y

Institute of Natural Resources
Departament of General Geology and Land

use planning
Total station
Lecturers: Berchuk V.Y.
Gutareva N.Y.
Contents
1. Definition;
2. Parts of the instrument;
3. The principe of operation;
4. Levelling the Total Station;
5. Levelling the Total Station.
2
Definition
Total station or TST (total station theodolite) is an
electronic/optical instrument used in modern surveying
and building construction. The total station is an
electronic theodolite (transit) integrated with an
electronic distance meter (EDM) to read slope
distances from the instrument to a particular point.
Sokia 105 Leica TS 06 Leica TS 09 3

Parts of the instrument
A Total station consists of:
4
Parts of the instrument
A Total station consists
of:
5
The principle of operation
The primary function of surveying
instruments is to measure distances, angles
and heights. The total station employs the
electro-optical distance metering method,
emitting laser beams to a target and detecting
light reflected off it. It takes measurements
by calculating the deviation of the
wavelength of the reflected light. Total
stations are able to measure distances to an
accuracy of 2-3 millimeters per kilometer,
and angles to 1-second (1°/3,600°) accuracy.
One second in an angle is equivalent to the
width of pencil lead at 100 meters.
6
Surveying instruments measure angles using a built-in encoder. The
encoder is a device that measures the rotation angle and number of
rotations of a built-in motor as digital data.
To measure the angle to a target point, the system creates a radial
pattern comprising 16,200 spokes at equal distance on a glass disc
and irradiates light with an LED diode. The encoder detects the
rotation angle of the motor by reading changes in the intensity of
the projected light. This way, the angle to the target is detected with
a resolution down to a one-second angle.
7
There are two methods of measuring distance: the “prism”
method, which uses a reflective prism at the target measurement
point, and the “non-prism,” or “reflectorless,” method that does
not use a reflective prism.
With the “prism” method, a laser is beamed at a
reflective prism (also called a mirror) placed at the
measurement point, and the distance is measured
by the time it takes for light to be reflected back
from the prism. Though this method is more
accurate than the “reflectorless” method, it requires
the placing of a reflective prism at the measurement
point, making it difficult to measure distances to
high locations, diagonal surfaces, or inaccessible
locations.
8
With the reflectorless method, it is possible to survey areas
from a distant location. Even areas of possible danger such as
disaster areas (e.g. landslides) can safely and efficiently be
surveyed with this method, which has the additional advantage
of requiring less labor and time (there is no need for a second
team to handle the prism at the target point).
When surveying roads, for example, traffic restrictions need to
be put into place if reflective prisms are used. This is not the
case with the reflectorless method. The decision to use the
prism or reflectorless method is made according to conditions
at the survey site.
The axes and circles of a theodolite

9
Levelling the Total Station
Leveling the Total Station must be accomplished to sufficient
accuracy otherwise the instrument will not report results
Leveling the instrument – make sure you can see all targets
from the instrument station before going through the process
The axes and circles of a theodolite

10
Tripod Setup
Tripod legs should be equally

spaced equally spaced
Tripod head should be
approximately level
Head should be directly over
survey point
11
Mount Instrument on Tripod
Place Instrument on Tripod

Secure with centering screw
while bracing the instrument
with the other hand
Insert battery in instrument
before leveling
12
Leveling the instrument
Focus the optical plummet on

the survey point
Adjust the leveling foot screws
to center the survey point in the
optical plummet reticle
Center the bubble in the
circular level by adjusting the
tripod legs
Loosen the horizontal clamp
and turn instrument until plate
level is parallel to 2 of the
leveling foot screws
13
Leveling the instrument
Center the bubble using the leveling screws —
the bubble moves toward the screw that is turned
clockwise
Rotate the instrument 90 degrees and level using
3rd leveling screw
Observe the survey point in the optical plummet
and center the point by loosening the centering
screw and sliding the entire instrument
After re-tightening the centering screw check to
make sure the plate level bubble is level in
several directions
14
Functions of Total station
1.It simultaneously measures angles & distances and Record
2. Correcting the measured distance with: 1. Prism constant
2. Atmospheric Pr.
3. Temperature
4. Curvature of earth
5. Refraction correction
3. Computing the point elevation
4. Computing the coordinates of every point
5. Remote elevation measurement
6. Remote distance measurement
7. Area calculations
8. Data Transferring facility from instrument to S/W and S/W
to instrument
9. Format of conversion of units
15

Total Station: Lecturers: Berchuk V.Y. Gutareva N.Y

Uploaded by

Copyright:

Available Formats

Total Station: Lecturers: Berchuk V.Y. Gutareva N.Y

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Total Station: Lecturers: Berchuk V.Y. Gutareva N.Y

Uploaded by

Copyright:

Available Formats

Institute of Natural Resources

Departament of General Geology and Land

Sokia 105 Leica TS 06 Leica TS 09 3

The axes and circles of a theodolite

The axes and circles of a theodolite

Tripod legs should be equally

Place Instrument on Tripod

Focus the optical plummet on

You might also like