INSTAKART SERVICES PVT.LTD.

, HARINGHATA
WATER TREATMENT PLANT - 240 KLD
SUMMARY

S.No Description Amount

1 WATER TREATMENT PLANT - 240 KLD -

SUB TOTAL -

GST @ 18 % -

TOTAL AMOUNT -
INSTAKART SERVICES INDIA PVT. LTD., HARINGHATA
WATER TREATMENT PLANT - 240 KLD
BILL OF QUANTITIES

TOTAL
S.No DESCRIPTION UNIT QUANTITY
RATE (Rs) AMOUNT (Rs)

On line Automatic Electronic Metered Chlorine Dosing system with polypropylene body
1.0 pumping system of capacity 0-4LPH at 35m head, including a 100L capacity storage tank No 1.00 0.00
(HDPE) etc., complete.

On line Automatic Coagulant Dosing system with polypropylene body pumping system of
2.0 capacity 60LPH at suitable head, including a 1000L capacity storage tank of MSRL MOC No 1.00 0.00
and mechanical stirrer

Supplying, installing, testing and commissioning of Raw Water lift mono block pump of 5
HP capable of giving required discharge at suitable head to work on 3 phase 50Hz 400/400
3.0 V with necessary unions, flanges, foundations bolts RCC footing, anti vibration pads etc.,
complete with head conditions. (1W+1S = 1 set)

Duty : 20 cum/hr@ 35m head (1W +1S ) sets 1.00 0.00

Supplying, installing, testing and commissioning approved make Dual Media filter of MS
construction shell thickness: 5 mm Dish thickness: 6 mm Inside with two coats of Epoxy
black paint and outside, outside two coats enamel painting over a primer coat with
necessary equipment complete with Frontal piping, valves, suitable supports for mounting,
pressure gauge, orifice plate , Filtering media: Graded, Gravel/Sand,Silex, pebbles and
Anthracite with manhole cover of 300 mm dia and air release valve etc..,complete as per
4.0 the detailed specification for the efficient working of system. The maximum working
Pressure shall be 3.5Kg/Sqcm. Maximum flux for filtration 15 m3/hr/m2. Min dia of vessel
1300mm. min HOS 1.5m

Capacity : 20 cum /hr @ 12.0 hr cycle No 1.00 0.00

Page 1 of 7
 TOTAL
S.No DESCRIPTION UNIT QUANTITY
Supplying, installing, testing and commissioning approved make MS Construction IRON
removal filter Shell thickness: 5 mm Dish thickness: 6 mm inside with two coats of Epoxy
black paint and outside, outside two coats enamel painting over a primer coat with
necessaryAncillary equipment complete with piping, valves , suitable supports for
mounting, pressure gauge, orifice plate , Filtering media: Graded, Gravel/Sand,Silex,
pebbles and Manganese Dioxide with manhole cover of 300 mm dia and air release valve
5.0 etc..,complete as per the detailed specification for the efficient working of system. The
maximum working Pressure shall be 3.5Kg/Sqcm. Maximum flux for filtration 12
m3/hr/m2. Min dia of vessel 1500mm. Min HOS 1.5m

Capacity : 20 cum /hr @ 12.0 hr cycle No QRO

Supplying, installing, testing and commissioning approved make activated corbon filters
MS construction shell thickness: 5 mm Dish thickness: 6 mm inside with two coats of Epoxy
black paint and outside, outside two coats enamel painting over a primer coat with
necessary Ancillary equipment complete with piping, valves ejector, orifice plate, salt
satuator made of corrosion resistant material etc., Filtering media: Graded, Gravel/Sand,
Activated carbon with manhole cover of 300 mm dia and air release valve complete as per
6.0 detailed specification for the efficient working of the system. Duty condition matching to
the outlet of IRF. The maximum working Pressure shall be 3.5Kg/Sqcm. Maximum flux for
filtration 12 m3/hr/m2. Min dia of vessel 1500mm. Min HOS 1.5m

Capacity : 20 cum /hr @ 12.0 hr cycle No 1.00 0.00

Page 2 of 7
 TOTAL
S.No DESCRIPTION UNIT QUANTITY
Supplying, installing, testing and commissioning approved make MS Construction water
softener shell thickness: 5 mm Dish thickness: 6 mm inside with two coats of Epoxy black
paint and outside, outside two coats enamel painting over a primer coat with necessary
Ancillary equipment complete with piping, valves ejector, orifice plate, salt satuator made
of corrosion resistant material and hardness testing kit etc., complete as per detailed
specification for the efficient working of the system. Duty condition matching to the outlet
of PSF, Considering a total hardness of 500 ppm and a maximum working pressure of 3.5
7.0 kg/cm2 etc.. Complete,with output hardness not more than 5 ppm at the end of the
softener and 50-80ppm after blending. OBR 240 KL with 10% blending. Resin Capacity
1900L, Min Dia of Vessel - 1200L, Min HOS 2.5 m

Capacity : 20 cum /hr @ 12.0 hr cycleB24:B25 No 1.00 0.00

Supplying, installing, testing and commissioning approved make required size of Brine
8.0 tank (2000L capacity HDPE tank) for salt regeneration with motorised stirrer necessary No 1.00 0.00
fittings & accessories etc.. Complete,

On line Automatic Electronic Metered Chlorine Dosing system with polypropylene body
9.0 pumping system capacity 0-4LPH at 35m head, including a 100L capacity storage tank No 1.00 0.00
(HDPE) etc., complete.

Supplying, installing, testing and commissioning panel of approved make to facilitate

10.0 operation of various based on tank level with necessary wiring, fittings & accessories (IP- Lot 1.00 0.00
56) etc.. Complete, including level switch for auto control

Page 3 of 7
 TOTAL
S.No DESCRIPTION UNIT QUANTITY
Supplying, installation, testing and commissioning of dewatering submersible pump set
suitable to handle 10-15mm solid size. Submersible pump should consists of S Tube
impeller, Bimetallic thermal sensor for motor over heating protection, double mechanical
cartridge seal, H class motor insulation, moisture detector for automatic cut-out for water
leakage, CED surface for all Cast Iron components, cable connection to motor via SS cable
11.0 plug and reliable clamp connection for easy access of internals of the pump without usage
of special tools. Pumps should be suitable to install with auto coupling (above 7.5KW) and
free standing installation(below 7.5KW) arrangements.

Type: Submersible drainage pump to handle muddy water.

Pump Housing: Cast iron, EN-GJL-250
Impeller: Cast iron, EN-GJL-250
Impellers Type: S Tube/ Vortex
Motor housing: Cast iron, EN-GJL-250
All O rings: NBR Rubber
Rotor shaft: stainless steel
Type Bearing: Double-row angular contact ball bearing.
Mechanical Seal: The primary seal is SiC/SiC and the secondary is
carbon/ceramic.
Free Ball Passage:- 10-12mm
No of pole: 2 or 4pole
Motor rpm: 2900/ 1450
Type of Motor :3 Phase Induction Motor.
Insulation Class: "H"
Protection sensor- Thermal and moisture sensor
Supply Voltage : 415 + 10%
Cycles/Sec. : 50 Hz + 5%
Pumps should be suitable to install with auto coupling (above 7.5KW) and free standing
installation(below 7.5KW) arrangements. Guide rail, Lifting chain and hook to be
considered.

a) Pump Duty Condition: 5 m3/hr at 25 Mt head to lift Pump room water water
0.0 Requirement no of pump : 1 Working + 1 Standby Set 2.00 0.00

Page 4 of 7
 TOTAL
S.No DESCRIPTION UNIT QUANTITY
Supplying, installing, testing and commissioning inter unit piping (PVC SCH 40) with
necessary flanges, bolts, nuts, neoprene gaskets, welding wherever necessary, with
12.0 necessary control valves, non return valves etc and with one coat of primer and two coats Lot 1.00 0.00
of approved enamel paint etc., complete.

TOTAL Amount -

Page 5 of 7
 LIST OF APPROVED MAKES - WATER TREATEMENT PLANT

Sl.No Material Make

1 Sand filter Clari fontaine/Ion exchange/Thermax/Hydrochemtech

2 Softener Clari fontaine//Ion exchange /Thermax/ Hydrochemtech /lanxess/purolite
3 Activated carbon filter Clari fontaine/ Ion exchange/ Thermax/ Hydrochemtech /lanxess/purolite

4 Chlorine dozer Prominent / Asia LMI/ Milton roy (Accudyne) /E-doze

5 Level switch Interlink / Sridhan International / Sri Vinayaka

6 Control Panel Siemens/ ABB/SCHNEIDER
7 PVC piping Supreme/Ashirvad /Astral

8 Water meter Aster/Actaris/Honeywell

9 Pumps Grundfos /Xylem/Kirloskar/KSB
10 RO Ion Exchange/Blue star/WAE.
11 FRP Tank s Oxygen / Kaveri/Equivalent
12 MSRL MOC Tanks Flowline/ Equivalent reputed make
13 HDPE Tanks Syntax/ Kaveri/ Equivalent
14 Water dispensers Ion Exchange/Blue star/WAE.
LIST OF RECOMMENDED ELECTRICAL MAKES

SL NO EQUIPMENT / ITEM MAKE

1 MCB DISTRIBUTION BOARDS LEGRAND/HAGER/SCHNEIDER
2 MCBS / ELCB/ELMCB LEGRAND/ABB / SIEMENS
3 PUSH BUTTONS / INDICATING SCHNEIDER / SIEMENS/TECHNIC
LAMPS
4 SELECTOR SWITCHES SCHNEIDER / SALZER / LEGRAND
5 TERMINALS CONNECTWELL/ELMEX
6 AUTOMATIC SOURCE CHANGE MGE (UA CONTROLLER )/ HPL / SOCOMEC (ATyS) / ABB ( ATS 010 )
OVER SYSTEM
7 PROTECTION RELAYS - ELECTRO SCHNEIDER/ ABB
MAGNETIC TYPE
8 EARTH LEAKAGE RELAY WITH CBCT PROK DEVICES/ ABB/SCHNEIDER

9 LT POWER & CONTROL CABLES - HAVELLS / PLOYCAB / GLOSTER

ALL ISI MARKED
10 CABLE GLANDS DOUBLE COMPRESSION TYPE, SIEMENS TYPE WITH RUBBER RING AND DOUBLE WASHERS FOR SIZES
ABOVE 70 SQMM.
FOR OUTDOOR APPLICATION IRRESPECTIVE OF THE SIZES DOUBLE COMPRESSION SHOULD BE
PROVIDED.
COMET/PRABHAT/SMI
11 CABLE LUGS DOWELLS/JAINSON
12 PVC INSULATED COPPER WIRES / HAVELLS / PLOYCAB / RR KABEL/ANCHOR
FRLS - ALL ISI MARKED
13 PVC CONDUITS / FRLS (ISI MARKED) 2MM THICK WALL THICKNESS ISI & FIA APPROVED AND MANUFACTURED FROM VIRGIN MATERIAL
- MINIMUM 2MM THICKNESS

PRECISION/AVON PLAST/BEC
14 FIRE BARRIERS 3M/HILTI