MODEL: 27HU

Head-mounted Two-wire Signal Conditioners RELATED PRODUCTS

27-UNIT • RS-232C interface Bell202 modem (model: COP-H)
Usable in ‘non-hazardous’ area only.
• USB interface Bell202 modem (model: COP-HU)
2-WIRE UNIVERSAL TEMPERATURE TRANSMITTER Usable in ‘non-hazardous’ area only.
(HART communication) • Hand-held communicator
Functions & Features • PC configurator software (model: 27HUCFG)
• Universal input: mV, T/C, RTD and resistance Downloadable at M-System’s web site.
• High accuracy
• HART communication
• Intrinsically safe approval GENERAL SPECIFICATIONS
• Suitable for Functional Safety applications up to SIL2 Construction: Sensor head-mounting
• Programming via hand-held communicator or via PC Connection: M3 screw terminals (torque 0.5 N·m)
• A wide variety of T/C and RTD types Screw terminal: Nickel-plated brass
• User’s temperature table can be used Housing material: Flame-resistant resin (black)
• Self diagnostics Isolation: Input to output
• Ultra-low temp. drift option (20 ppm/°C typ.) User-configurable items:
• CE marking (conforms to ATEX and EMC) · Input sensor type and numbers
· Number of wires (RTD & resistance)
· Input range (inverted range selectable)
· Burnout
44 (1.73) DIA.
· Output limits (Upper / Lower)
· Damping time (factory set to 0)
· Cold junction compensation (T/C; internal or external
20.7
(.81) sensor selectable)
· Linearization
mm (inch) · Sensor calibration
· Output calibration
· HART communication mode
Refer to the HART setup manual or the PC configurator
MODEL: 27HU–[1][2] users manual for the detail.

ORDERING INFORMATION HART COMMUNICATION

• Code number: 27HU-[1][2] Protocol: HART communication protocol
Specify a code from below for each [1], [2]. HART address range: 0 – 15 (factory set to 0)
(e.g. 27HU-2) Transmission speed: 1200 bps
Use Ordering Information Sheet (No. ESU-7651). Factory Digital current: Approx. 1 mAp-p when communicating
standard setting will be used if not otherwise specified. Character format: 1 Start Bit, 8 Data Bits, 1 Odd Parity Bit,
Specify the country in which the product is to be used with 1 Stop Bit
the Safety Approval code 2. Distance: 1.5 km (0.9 miles)
HART communication mode: Master-Slave Mode and Burst
[1] SAFETY APPROVAL Mode (factory set to Master-Slave)
0: None HART network mode: Point-to-Point Mode and Multi-drop
1: FM intrinsically safe Mode; automatically set to Multi-drop Mode when the
2: CENELEC intrinsic safety (ATEX) address is set to other than 0.

[2] OPTIONS INPUT SPECIFICATIONS

Temperature drift The input is factory set for use with K thermocouple, single
Blank: Standard (temp. coefficient 0.015%/°C) input, 0 to 100°C, internal CJC sensor.
/L: Ultra-low temperature drift See Table 1 for the available input type, the minimum span
(temp. coefficient 0.002%/°C typ., 0.005%/°C max.) and the maximum range.
• DC mV (dual input available)

http://www.m-system.co.jp/ 27HU SPECIFICATIONS ES-7651 Rev.9 Page 1/5

 MODEL: 27HU
Input resistance: ≥ 1 MΩ use in a safety instrumented system up to SIL2 (together
• THERMOCOUPLE (dual input available) with sensor) if appropriate safety instructions are observed.
Input resistance: ≥ 1 MΩ Consult M-System.
Burnout sensing: 33 μA
External CJC sensor type: Pt 100
STANDARDS & APPROVALS
• RTD (2-wire, 3-wire or 4-wire)
CE conformity:
Input resistance: ≥ 1 MΩ
ATEX Directive (94/9/EC)
Excitation: 0.2 mA
Ex ia EN 60079-11
Allowable leadwire resistance: Max. 10 Ω per wire
EMC Directive (2004/108/EC)
• RESISTANCE (2-wire, 3-wire or 4-wire)
EMI EN 61000-6-4
Input resistance: ≥ 1 MΩ
EMS EN 61000-6-2
Excitation: 0.2 mA
Safety approval:
Allowable leadwire resistance: Max. 10 Ω per wire
FM: Intrinsically safe
Class I, Division 1, Groups A, B, C and D
OUTPUT SPECIFICATIONS Class I, Zone 0, AEx ia IIC (US)
Output range: 4 – 20 mA DC Class I, Zone 0, Ex ia IIC (Canada)
Operational range: 3.75 – 23 mA T4, T5 and T6
Load resistance vs. supply voltage: (Class 3610, ANSI/ISA 60079-11,
Load Resistance (Ω) = (Supply Voltage (V) – 8 (V)) CAN/CSA-C22.2 No. 157,
/ 0.023 (A) (including leadwire resistance) CAN/CSA-C22.2 No. 60079-11)
Burnout: 3.75 – 3.8 mA or 21.5 – 23 mA CENELEC: Intrinsic safety (ATEX)
(factory set to 23 mA) Ⅱ 1G, Ex ia ⅡC; T4, T5 and T6
Upper output limit proportional to the input: (EN 60079-11: 2007)
20 – 21.5 mA (factory set to 21.5 mA)
Lower output limit proportional to the input:
3.8 – 4 mA (factory set to 3.8 mA)
SAFETY PARAMETERS
Operating temperature
Update time: 440 msec. (660 msec. with dual input)
For CENELEC (ATEX) / FM:
Output characteristics for dual input:
T4: -40 to +80°C
Average or Differential selectable
T5: -40 to +60°C
T6: -40 to +45°C
INSTALLATION Ex-data:
Supply voltage: • Output circuit
· 8 – 35 V DC (non-approved) Ui (Vmax): 30 V DC
· 8 – 28 V DC (approved) Ii (Imax): 96 mA DC
Operating temperature: -40 to +85°C (-40 to +185°F) Pi (Pmax): 720 mW
(See Safety Parameters for use in a hazardous Ci: 1 nF
location.) Li: 0 mH
Operating humidity: 0 to 95 %RH (non-condensing) • Sensor circuit
Mounting: Head-mounting (DIN type B head) Uo (Voc): 30 V DC
Weight: 50 g (1.76 oz) Io (Isc): 24 mA DC
Po: 180 mW
PERFORMANCE Co (Ca): 50 nF
Accuracy: See Table 1. Lo (La): 40 mH
Cold junction compensation accuracy: ±0.5°C with internal
CJC sensor
Response time: ≤ 2 sec. (0 – 90 %) with damping time
set to 0 and when not communicating via HART.
Supply voltage effect: ±0.05 % of span/V
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @1 minute (input to output)
Safety integrity level according to IEC 61508: Suitable for

http://www.m-system.co.jp/ 27HU SPECIFICATIONS ES-7651 Rev.9 Page 2/5

 MODEL: 27HU
INPUT TYPE, RANGE & ACCURACY
■ INPUT TYPE, RANGE & ACCURACY Table 1
TEMPERATURE DRIFT
INPUT TYPE MINIMUM MAXIMUM ACCRACY STANDARD ULTRA-LOW
SPAN RANGE *1 DRIFT *2 DRIFT *3
DC mV 4 mV -100 to +800 mV ±10 µV ±1.5 µV/°C ±0.5 µV/°C
Resistance 25 Ω 0 to 4 kΩ ±0.1 Ω ±15 mΩ/°C ±5 mΩ/°C
°C °F TEMPERATURE DRIFT
Thermocouple MINIMUM MAXIMUM ACCURACY MINIMUM MAXIMUM ACCURACY STANDARD ULTRA-LOW
SPAN RANGE *1 SPAN RANGE *1 DRIFT*2 DRIFT*3
K (CA) 50 -180 to +1372 ±0.5 90 -292 to +2501 ±0.9 ±0.075°C/°C ±0.025°C/°C
E (CRC) 50 -100 to +1000 ±0.5 90 -148 to +1832 ±0.9 ±0.075°C/° ±0.025°C/°C
J (IC) 50 -100 to +1200 ±0.5 90 -148 to +2192 ±0.9 ±0.075°C/°C ±0.025°C/°C
T (CC) 50 -200 to +400 ±0.5 90 -328 to +752 ±0.9 ±0.075°C/°C ±0.025°C/°C
B (RH) 100 400 to 1820 ±1 180 752 to 3308 ±1.8 ±0.3°C/°C ±0.1°C/°C
R 100 -50 to +1760*4 ±1 180 -58 to +3200*4 ±1.8 ±0.3°C/°C ±0.1°C/°C
S 100 -50 to +1760*4 ±1 180 -58 to +3200*4 ±1.8 ±0.3°C/°C ±0.1°C/°C
C (WRe 5-26) 100 0 to 2300 ±1 180 32 to 4172 ±1.8 ±0.3°C/°C ±0.1°C/°C
D (WRe 3-25) 100 0 to 2300 ±1 180 32 to 4172 ±1.8 ±0.3°C/°C ±0.1°C/°C
N 50 -180 to +1300 ±0.5 90 -292 to +2372 ±0.9 ±0.075°C/°C ±0.025°C/°C
U 50 -200 to +600 ±0.5 90 -328 to +1112 ±0.9 ±0.075°C/°C ±0.025°C/°C
L 50 -100 to +900 ±0.5 90 -148 to +1652 ±0.9 ±0.075°C/°C ±0.025°C/°C
°C °F TEMPERATURE
RTD MINIMUM MAXIMUM ACCRACY MINIMUM MAXIMUM ACCRACY STANDARD ULTRA-LOW
SPAN RANGE *1 SPAN RANGE *1 DRIFT *2 DRIFT *3

Pt 100 (JIS '97, IEC) 10 -200 to +850 ±0.1 18 -328 to +1562 ±0.18 ±0.015°C/°C ±0.005°C/°C
Pt 200 10 -200 to +850 ±0.1 18 -328 to +1562 ±0.18 ±0.015°C/°C ±0.005°C/°C
Pt 500 10 -200 to +850 ±0.1 18 -328 to +1562 ±0.18 ±0.015°C/°C ±0.005°C/°C
Pt 1000 10 -200 to +850 ±0.1 18 -328 to +1562 ±0.18 ±0.015°C/°C ±0.005°C/°C
JPt 100 (JIS '89) 10 -200 to +510 ±0.1 18 -328 to +950 ±0.18 ±0.015°C/°C ±0.005°C/°C
Ni 100 (DIN 43760 '87) 10 -60 to +250 ±0.2 18 -76 to +482 ±0.36 ±0.015°C/°C ±0.005°C/°C
*1. DC mV: Or ±0.05 % of absolute range (greater of 0 % and 100 % range values), whichever is greater.
Or ±0.2 % of absolute negative range for two inputs including negative ranges, whichever is greater.
Resistance: Or ±0.05 % of absolute range (greater of 0 % and 100 % range values), whichever is greater.
Thermocouple: Or ±0.05 % of span, whichever is greater. Add cold junction compensation error.
RTD: Or ±0.05 % of max. range (greater of 0 % and 100 % range values converted into °C), whichever is greater.
(For 2- or 3-wire RTD, the value is valid by the sensor calibration after wiring is complete.)
*2. Or ±0.015 % of absolute range/°C (greater of 0 % and 100 % range values), whichever is greater.
*3. Or ±0.005 % of absolute range/°C (greater of 0 % and 100 % range values), whichever is greater.
*4. Conformance range: 50 to 1760°C or 122 to 3200°F

DIMENSIONS unit: mm (inch)

44 (1.73) dia. 20.7 (.81)
33 (1.30) 6 (.24) dia. 19.5 (.77)
16.5 (.65) 12.7 (.5)

2–4.5 (.18) dia.

MTG HOLE
+ –

1 4
6.3

2 3
5)
(.2

6–M3 SCREW

http://www.m-system.co.jp/ 27HU SPECIFICATIONS ES-7651 Rev.9 Page 3/5

 MODEL: 27HU
MOUNTING REQUIREMENTS unit: mm (inch)
33 (1.30)
2–M4 SCREW

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Hazardous Location Non-Hazardous Location

HART
Comm.

Isolation
24 V DC
Input Output Output +
4 Computation Computation Driver *2
Low Drift
OUTPUT LOAD
Amplifier
3 –
INPUT *1 4 – 20 mA DC
2
Safety Barrier *3
1

CJC
Sensor

*1. Input Connection Examples

■ DC MILLIVOLT ■ THEMOCOUPLE ■ RTD & RESISTANCE
• Internal CJC • Two-wire
4 comp. leadwire 4 B 4

– 3 – –
3 3
INPUT
+ 2 +
+ 2 2

1 1 A 1

• Two Inputs • External CJC • Three-wire

– 4 comp. leadwire 4 B 4

+ 3 – –
INPUT 2 3 B 3

+ 2 +
INPUT 1 + 2 2

1 1 A 1

• Two Inputs, Internal CJC • Four-wire

–
4 B 4
+
SENSOR 2 – + 3 B 3
+
SENSOR 1 – + 2 A 2
comp. leadwire
1 A 1

• Two Inputs, External CJC

–
4
+
SENSOR 2 – + 3
+
SENSOR 1 – + 2
comp. leadwire
1

*2. Limited to 250 – 1100Ω for HART communication.

*3. A safety barrier must be installed for the intrinsic safety.
The safety barrier must meet the Ex-data of this unit and must be approved for the hazardous location.

http://www.m-system.co.jp/ 27HU SPECIFICATIONS ES-7651 Rev.9 Page 4/5

 MODEL: 27HU

Specifications are subject to change without notice.

http://www.m-system.co.jp/ 27HU SPECIFICATIONS ES-7651 Rev.9 Page 5/5