Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

PIC16LF15376 Data Sheet

Download as pdf or txt
Download as pdf or txt
You are on page 1of 605

PIC16(L)F15356/75/76/85/86

Full-Featured 28/40/44/48-Pin Microcontrollers

Description
PIC16(L)F15356/75/76/85/86 microcontrollers feature Analog, Core Independent Peripherals and Communication
Peripherals, combined with eXtreme Low-Power (XLP) technology for a wide range of general purpose and low-power
applications.
The devices feature multiple PWMs, multiple communication, temperature sensor, and memory features like Memory
Access Partition (MAP) to support customers in data protection and bootloader applications, and Device Information
Area (DIA) which stores factory calibration values to help improve temperature sensor accuracy.

Core Features Power-Saving Functionality


• C Compiler Optimized RISC Architecture • DOZE mode: Ability to Run the CPU Core Slower
• Operating Speed: than the System Clock
- DC – 32 MHz clock input • IDLE mode: Ability to halt CPU Core while Internal
- 125 ns minimum instruction cycle Peripherals Continue Operating
• Interrupt Capability • SLEEP mode: Lowest Power Consumption
• 16-Level Deep Hardware Stack • Peripheral Module Disable (PMD):
• Timers: - Ability to disable hardware module to
- 8-bit Timer2 with Hardware Limit Timer (HLT) minimize active power consumption of
- 16-bit Timer0/1 unused peripherals
• Low-Current Power-on Reset (POR)
• Configurable Power-up Timer (PWRTE) eXtreme Low-Power (XLP) Features
• Brown-out Reset (BOR)
• Low-Power BOR (LPBOR) Option • Sleep mode: 50 nA @ 1.8V, typical
• Windowed Watchdog Timer (WWDT): • Watchdog Timer: 500 nA @ 1.8V, typical
- Variable prescaler selection • Secondary Oscillator: 500 nA @ 32 kHz
- Variable window size selection • Operating Current:
- All sources configurable in hardware or - 8 A @ 32 kHz, 1.8V, typical
software - 32 A/MHz @ 1.8V, typical
• Programmable Code Protection
Digital Peripherals
Memory • Four Configurable Logic Cells (CLC):
• Up to 28 KB Flash Program Memory - Integrated combinational and sequential logic
• Up to 2 Bytes Data SRAM • Complementary Waveform Generator (CWG):
• Direct, Indirect and Relative Addressing modes - Rising and falling edge dead-band control
• Memory Access Partition (MAP): - Full-bridge, half-bridge, 1-channel drive
- Write protect - Multiple signal sources
- Customizable Partition • Two Capture/Compare/PWM (CCP) module:
• Device Information Area (DIA) - 16-bit resolution for Capture/Compare modes
• Device Configuration Information (DCI) - 10-bit resolution for PWM mode
• High-Endurance Flash (HEF) • Four 10-Bit PWMs
- Last 128 words of Program Flash Memory • Numerically Controlled Oscillator (NCO):
- Generates true linear frequency control and
Operating Characteristics increased frequency resolution
- Input Clock: 0 Hz < FNCO < 32 MHz
• Operating Voltage Range: - Resolution: FNCO/220
- 1.8V to 3.6V (PIC16LF15356/75/76/85/86) • Two EUSART, RS-232, RS-485, LIN compatible
- 2.3V to 5.5V (PIC16F15356/75/76/85/86) • Two SPI
• Temperature Range: • Two I2C, SMBus, PMBus™ compatible
- Industrial: -40°C to 85°C
- Extended: -40°C to 125°C

 2016-2018 Microchip Technology Inc. DS40001866B-page 1


PIC16(L)F15356/75/76/85/86
Digital Peripherals (Cont.) Flexible Oscillator Structure
• I/O Pins: • High-Precision Internal Oscillator:
- Individually programmable pull-ups - Software selectable frequency range up to 32
- Slew rate control MHz, ±1% typical
- Interrupt-on-change with edge-select • x2/x4 PLL with Internal and External Sources
- Input level selection control (ST or TTL) • Low-Power Internal 32 kHz Oscillator
- Digital open-drain enable (LFINTOSC)
• Peripheral Pin Select (PPS): • External 32 kHz Crystal Oscillator (SOSC)
- Enables pin mapping of digital I/O • External Oscillator Block with:
- Three crystal/resonator modes up to 20 MHz
Analog Peripherals - Three external clock modes up to 32 MHz
• Fail-Safe Clock Monitor:
• Analog-to-Digital Converter (ADC): - Allows for safe shutdown if primary clock
- 10-bit with up to 43 external channels stops
- Operates in Sleep • Oscillator Start-up Timer (OST):
• Two Comparators: - Ensures stability of crystal oscillator
- FVR, DAC and external input pin available on resources
inverting and noninverting input
- Software selectable hysteresis
- Outputs available internally to other modules,
or externally through PPS
• 5-Bit Digital-to-Analog Converter (DAC):
- 5-bit resolution, rail-to-rail
- Positive Reference Selection
- Unbuffered I/O pin output
- Internal connections to ADCs and
comparators
• Voltage Reference:
- Fixed Voltage Reference with 1.024V, 2.048V
and 4.096V output levels
• Zero-Cross Detect module:
- AC high voltage zero-crossing detection for
simplifying TRIAC control
- Synchronized switching control and timing

 2016-2018 Microchip Technology Inc. DS40001866B-page 2


PIC16(L)F15356/75/76/85/86
TABLE 1: PIC16(L)F153XX FAMILY TYPES

Program Flash Memory (KW)

Program Flash Memory (KB)

Peripheral Module Disable


Memory Access Partition
Window Watchdog Timer

Device Information Area


Storage Area Flash (B)

Temperature Indicator
8-bit/ (with HLT) Timer

Peripheral Pin Select


Zero-Cross Detect

EUSART/ I2C-SPI
Data Sheet Index

CCP/10-bit PWM
16-bit Timer
Comparator
Data SRAM

10-bit ADC

5-bit DAC

Debug (1)
I/OPins
(bytes)

CWG
NCO
CLC
Device

PIC16(L)F15313 (C) 2 3.5 224 256 6 5 1 1 1 2 Y 2/4 1 1 4 Y Y Y Y 1/1 Y Y I


PIC16(L)F15323 (C) 2 3.5 224 256 12 11 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 1/1 Y Y I
PIC16(L)F15324 (D) 4 7 224 512 12 11 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/1 Y Y I
PIC16(L)F15325 (B) 8 14 224 1024 12 11 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/1 Y Y I
PIC16(L)F15344 (D) 4 7 224 512 18 17 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/1 Y Y I
PIC16(L)F15345 (B) 8 14 224 1024 18 17 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/1 Y Y I
PIC16(L)F15354 (A) 4 7 224 512 25 24 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15355 (A) 8 14 224 1024 25 24 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15356 (E) 16 28 224 2048 25 24 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15375 (E) 8 14 224 1024 36 35 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15376 (E) 16 28 224 2048 36 35 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15385 (E) 8 14 224 1024 44 43 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
PIC16(L)F15386 (E) 16 28 224 2048 44 43 1 2 1 2 Y 2/4 1 1 4 Y Y Y Y 2/2 Y Y I
Note 1: I - Debugging integrated on chip.
Data Sheet Index:
A: DS40001853 PIC16(L)F15354/5 Data Sheet, 28-Pin
B: DS40001865 PIC16(L)F15325/45 Data Sheet, 14/20-Pin
C: DS40001897 PIC16(L)F15313/23 Data Sheet, 8/14-Pin
D: DS40001889 PIC16(L)F15324/44 Data Sheet, 14/20-Pin
E: DS40001866 PIC16(L)F15356/75/76/85/86 Data Sheet, 28/40/48-Pin

Note: For other small form-factor package availability and marking information, visit www.microchip.com/
packaging or contact your local sales office.

 2016-2018 Microchip Technology Inc. DS40001866B-page 3


PIC16(L)F15356/75/76/85/86
TABLE 2: PACKAGES
TQFP TQFP QFN QFN UQFN UQFN UQFN
Device (S)PDIP SOIC SSOP
(7x7) (10x10) (8x8) (6x6) (4x4) (5x5) (6x6)
PIC16(L)F15356     
PIC16(L)F15375    
PIC16(L)F15376    
PIC16(L)F15385  
PIC16(L)F15386  

 2016-2018 Microchip Technology Inc. DS40001866B-page 4


PIC16(L)F15356/75/76/85/86
PIN DIAGRAMS

28-PIN PDIP, SOIC, SSOP


VPP/MCLR/RE3 1 28 RB7/ICSPDAT
RA0 2 27 RB6/ICSPCLK
RA1 3 26 RB5
RA2 4 25 RB4
RA3 5 24 RB3

PIC16(L)F15356
RA4 6 23 RB2
RA5 7 22 RB1
VSS 8 21 RB0
RA7 9 20 VDD
RA6 10 19 VSS
RC0 11 18 RC7
RC1 12 17 RC6
RC2 13 16 RC5
RC3 14 15 RC4

Note 1: See Table 3 for location of all peripheral functions.


2: All VDD and all VSS pins must be connected at the circuit board level.

40-PIN PDIP
VPP/MCLR/RE3 1 40 RB7/ICSPDAT
RA0 2 39 RB6/ICSPCLK
RA1 3 38 RB5
RA2 4 37 RB4
RA3 5 36 RB3
RA4 6 35 RB2
RA5 7 34 RB1
RE0 8 33 RB0
PIC16(L)F15375
PIC16(L)F15376

RE1 9 32 VDD
RE2 10 31 VSS
VDD 11 30 RD7
VSS 12 29 RD6
RA7 13 28 RD5
RA6 14 27 RD4
RC0 15 26 RC7
RC1 16 25 RC6
RC2 17 24 RC5
RC3 18 23 RC4
RD0 19 22 RD3
RD1 20 21 RD2

Note: See Table 4 for location of all peripheral functions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 5


PIC16(L)F15356/75/76/85/86

28-PIN UQFN (4x4), UQFN (6x6)

RE3/MCLR/VPP

RB6/ICSPCLK
RB7/ICSPDAT
RA1
RA0

RB5
RB4
28
27
26

24
23
22
25
RA2 1 21 RB3
RA3 2 20 RB2
RA4 3 19 RB1
RA5 4 18 RB0
PIC16(L)F15356
VSS 5 17 VDD
RA7 6 16 VSS
RA6 7 15 RC7

10

12
13
14
11
8
9 RC1
RC2
RC3

RC6
RC0

RC4
RC5
Note 1: See Table 3 for location of all peripheral functions.
2: All VDD and all VSS pins must be connected at the circuit board level. Allowing one or more VSS or VDD pins to
float may result in degraded electrical performance or non-functionality.
3: The bottom pad of the QFN/UQFN package should be connected to VSS at the circuit board level.
RC5

40-PIN UQFN (5x5)


RC6

RC4
RD3
RD2
RD1
RD0
RC3
RC2
RC1
34
40
39

37
36
35

31
33
32
38

RC7 1
RD4 2 30 RC0
RD5 3 29 RA6
RD6 4 28 RA7
RD7 5 27 VSS
PIC16(L)F15375
VSS 6 PIC16(L)F15376 26 VDD
VDD 7 25 RE2
RB0 8 24 RE1
9 23 RE0
RB1
10 22 RA5
RB2
21 RA4
12
13
14
15
16
17
18
19
20
11 RB3
RB4
RB5

RA0

RA2
RA3
RA1
ICSPDAT/RB7
VPP/MCLR/RE3
ICSPCLK/RB6

Note 1: See Table 4 for the pin allocation tables.


2: The bottom pad of the QFN/UQFN package should be connected to VSS at the circuit board level.

 2016-2018 Microchip Technology Inc. DS40001866B-page 6


PIC16(L)F15356/75/76/85/86

RC5
RC6

RC4
RD3
RD2
RD1
RD0
RC3
RC2
RC1
44-PIN TQFP (10x10)

NC
41
40
39

37
36
35
34
42
44
43

38
RC7 1 33 NC
RD4 2 32 RC0
RD5 3 31 RA6
4 30 RA7
RD6
5 29 VSS
RD7 PIC16(L)F15375
6 PIC16(L)F15376 28 VDD
VSS
27 RE2
VDD 7
RB0 8 26 RE1
25 RE0
RB1 9
24 RA5
RB2 10
23 RA4
RB3 11 12
13
14
15
16
17
18
19
20
21
22
NC
NC

ICSPCLK/RB6
ICSPDAT/RB7

RA2
RA3
RB4
RB5

VPP/MCLR/RE3
AN0/RA0
RA1
Note 1: See Table 4 for location of all peripheral functions.
2: All VDD and all VSS pins must be connected at the circuit board level. Allowing one or more VSS or VDD pins to float
may result in degraded electrical performance or non-functionality.

44-PIN QFN (8x8x0.9)


RC6
RC5
RC4
RD3
RD2
RD1
RD0
RC3
RC2
RC1
RC0
44
43
42
41
40
39
37
36
35
34
38

RC7 1 33 RA6
RD4 2 32 RA7
RD5 3 31 NC
RD6 4 30 VSS
RD7 5 29 NC
VSS 6 PIC16(L)F15375 28
PIC16(L)F15376 VDD
VDD 7 27 RE2
NC 8 26 RE1
RB0 9 25 RE0
RB1 10 24 RA5
RB2 11 23 RA4
22
12
13
14
15
16
17
18
19
20
21
RA1
RA2
RA3
ICSPDAT/RB7
RB3
RB4
RB5

RA0
NC

ICSPCLK/RB6
VPP/MCLR/RE3

Note 1: See Table 4 for location of all peripheral functions.


2: All VDD and all VSS pins must be connected at the circuit board level. Allowing one or more VSS or VDD pins to fl
may result in degraded electrical performance or non-functionality.
3: The bottom pad of the QFN/UQFN package should be connected to VSS at the circuit board level.

 2016-2018 Microchip Technology Inc. DS40001866B-page 7


PIC16(L)F15356/75/76/85/86

48-PIN UQFN (6x6)

RC6
RC5
RC4
RD3
RD2
RD1
RD0
RC3
RC2
RF3
RF2
RF1
48 47 46 45 44 43 42 41 40 39 38 37
RC7 1 36 RF0
RD4 2 35 RC1
RD5 3 34 RC0
RD6 4 33 RA6

RD7 5 32 RA7
PIC16(L)F15385 31 VSS
VSS 6
PIC16(L)F15386
VDD 7 30 VDD

RB0 8 29 RE2

RB1 9 28 RE1

RB2 10 27 RE0

RB3 11 26 RA5
RF4 12 25 RA4
13 14 15 16 17 18 19 20 21 22 23 24
RF5
RF6
RF7
RB4
RB5
ICSPCLK/RB6
ICSPDAT/RB7
VPP/MCLR/RE3
RA0
RA1
RA2
RA3
Note 1: See Table 5 for location of all peripheral functions.
2: The bottom pad of the QFN/UQFN package should be connected to Vss as the circuit board level.

48-PIN TQFP (7x7)


RC5
RC6

RC4
RD3
RD2
RD1
RD0
RC3
RC2
RF3
RF2
RF1
45
44
43

41
40
39

37
46
48
47

38
42

RC7 1 36 RF0
RD4 2 35 RC1
RD5 3
34 RC0
RD6 4 RA6
33
RD7 5 32 RA7
VSS 6 PIC16(L)F15385 31 VSS
VDD 7 PIC16(L)F15386 30 VDD
RB0 8 29 RE2
RB1 9 28 RE1
RB2 10 27 RE0
RB3 11 26 RA5
RF4 12 25 RA4
13
14
15
16
17
18
19
20
21
22
23
24
RF5
RF6
RF7

ICSPDAT/RB7
VPP/MCLR/RE3
RB4
RB5
ICSPCLK/RB6

RA0
RA1
RA2
RA3

Note: See Table 5 for location of all peripheral functions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 8


PIN ALLOCATION TABLES
 2016-2018 Microchip Technology Inc.

TABLE 3: 28-PIN ALLOCATION TABLE (PIC16(L)F15356)


28-Pin PDIP/SOIC/SSOP

28-Pin UQFN

Comparator
Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
CWG
PWM
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
C1IN0-
RA0 2 27 ANA0 ― ― ― ― ― ― ― ― ― ― CLCIN0(1) ― IOCA0 Y ―
C2IN0-
C1IN1-
RA1 3 28 ANA1 ― ― ― ― ― ― ― ― ― ― CLCIN1(1) ― IOCA1 Y ―
C2IN1-
C1IN0+
RA2 4 1 ANA2 — ― DAC1OUT1 ― ― ― ― ― ― ― ― ― IOCA2 Y ―
C2IN0+

PIC16(L)F15356/75/76/85/86
RA3 5 2 ANA3 VREF+ C1IN1+ ― DAC1REF+ ― ― ― ― ― ― ― ― ― IOCA3 Y ―
RA4 6 3 ANA4 ― ― ― ― T0CKI ― ― ― ― ― ― ― ― IOCA4 Y ―
RA5 7 4 ANA5 ― ― ― ― — ― ― ― SS1(1) ― ― ― ― IOCA5 Y ―
CLKOUT
RA6 10 7 ANA6 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA6 Y
OSC2
CLKIN
RA7 9 6 ANA7 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA7 Y
OSC1
INT(1)
RB0 21 18 ANB0 ― C2IN1+ ― ― ― ― ― CWG1IN(1) SS2(1) ZCD1 ― ― ― Y ―
IOCB0
C1IN3- SCK2,
RB1 22 19 ANB1 ― ― ― ― ― ― ― ― ― ― ― IOCB1 Y ―
C2IN3- SCL2(1,4)
SDA2,
RB2 23 20 ANB2 ― ― ― ― ― ― ― ― ― ― ― ― IOCB2 Y ―
SDI2(1,4)
C1IN2-
RB3 24 21 ANB3 ― ― ― ― ― ― ― ― ― ― ― ― IOCB3 Y ―
C2IN2-
ANB4
RB4 25 22 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCB4 Y ―
ADACT(1)
(1)
RB5 26 23 ANB5 ― ― ― ― T1G ― ― ― ― ― ― ― ― IOCB5 Y ―
TX2
RB6 27 24 ANB6 ― ― ― ― ― ― ― ― ― ― CLCIN2(1) ― IOCB6 Y ICSPCLK
CK2(1)
DS40001866B-page 9

RX2
RB7 28 25 ANB7 ― ― ― DAC1OUT2 ― ― ― ― ― ― CLCIN3(1) ― IOCB7 Y ICSPDAT
DT2(1)
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS remappable. These signals may be mapped to output onto one or more PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBus input buffer thresholds.
TABLE 3: 28-PIN ALLOCATION TABLE (PIC16(L)F15356) (CONTINUED)
 2016-2018 Microchip Technology Inc.

28-Pin PDIP/SOIC/SSOP

28-Pin UQFN

Comparator
Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
CWG
PWM
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
SOSCO
RC0 11 8 ANC0 ― ― ― ― ― ― ― ― ― ― ― ― IOCC0 Y ―
T1CKI
RC1 12 9 ANC1 ― ― ― ― SOSCI CCP2(1) ― ― ― ― ― ― ― IOCC1 Y ―
RC2 13 10 ANC2 ― ― ― ― ― CCP1(1) ― ― ― ― ― ― ― IOCC2 Y ―
SCL1,
RC3 14 11 ANC3 ― ― ― ― T2IN(1) ― ― ― ― ― ― ― IOCC3 Y ―
SCK1(1,4)
SDA1,
RC4 15 12 ANC4 ― ― ― ― ― ― ― ― ― ― ― ― IOCC4 Y ―
SDI1(1,4)
RC5 16 13 ANC5 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCC5 Y ―

PIC16(L)F15356/75/76/85/86
TX1
RC6 17 14 ANC6 ― ― ― ― ― ― ― ― ― ― ― ― IOCC6 Y ―
CK1(1)
RX1
RC7 18 15 ANC7 ― ― ― ― ― ― ― ― ― ― ― ― IOCC7 Y ―
DT1(1)
MCLR
RE3 1 26 — ― ― ― ― ― ― ― ― ― ― ― ― ― IOCE3 Y
VPP
VDD 20 17 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VDD
VSS 8 16 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
VSS 19 5 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
OUT(2) CWG1A
― ― ― ― C1OUT NCO1OUT ― TMR0 CCP1 PWM3OUT SDO1/2 ― DT(1,2) CLC1OUT CLKR ― ― ―
CWG2A
CWG1B
― ― ― ― C2OUT ― ― ― CCP2 PWM4OUT SCK1/2 ― CK(1,2) CLC2OUT ― ― ― ―
CWG2B
CWG1C SCL1(3,4)
― ― ― ― ― ― ― ― ― PWM5OUT ― TX(1,2) CLC3OUT ― ― ― ―
CWG2C SCL2(3,4)
CWG1D SDA1(3,4)
― ― ― ― ― ― ― ― ― PWM6OUT ― ― CLC4OUT ― ― ― ―
CWG2D SDA2(3,4)
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS remappable. These signals may be mapped to output onto one or more PORTx pin options.
DS40001866B-page 10

3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBus input buffer thresholds.
 2016-2018 Microchip Technology Inc.

TABLE 4: 40/44-PIN ALLOCATION TABLE (PIC16(L)F15375, PIC16(L)F15376)


40-Pin UQFN

44-Pin TQFP

Comparator
40-Pin PDIP

44-Pin QFN

Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
CWG
PWM
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
RA0 2 17 19 19 ANA0 ― C1IN0- ― ― ― ― ― ― ― ― ― CLCIN0(1) ― IOCA0 Y ―
C2IN0-
RA1 3 18 20 20 ANA1 ― C1IN1- ― ― ― ― ― ― ― ― ― CLCIN1(1) ― IOCA1 Y ―
C2IN1-
RA2 4 19 21 21 ANA2 ― C1IN0+ ― DAC1OUT1 ― ― ― ― ― ― ― ― ― IOCA2 Y ―
C2IN0+
RA3 5 20 22 22 ANA3 VREF+ C1IN1+ ― DACREF+ ― ― ― ― ― ― ― ― ― IOCA3 Y ―
RA4 6 21 23 23 ANA4 ― ― ― ― T0CKI(1) ― ― ― ― ― ― ― ― IOCA4 Y ―
RA5 7 22 24 24 ANA5 ― ― ― ― T1G(1) ― ― ― SS1(1) ― ― ― ― IOCA5 Y ―
RA6 14 29 33 31 ANA6 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA6 Y CLKOUT/
OSC1

PIC16(L)F15356/75/76/85/86
RA7 13 28 32 30 ANA7 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA7 Y CLKIN/
OSC2
RB0 33 8 9 8 ANB0 ― C2IN1+ ― ― ― ― ― CWG1(1) SS2(1) ZCD1 ― ― ― INT(1) Y ―
IOCB0
RB1 34 9 10 9 ANB1 ― C1IN3- ― ― ― ― ― ― SCL1 ― ― ― ― IOCB1 Y ―
C2IN3- SCK1(1,4)
RB2 35 10 11 10 ANB2 ― ― ― ― ― ― ― ― SDA1 ― ― ― ― IOCB2 Y ―
SDI1(1,4)
RB3 36 11 12 11 ANB3 ― C1IN2- ― ― ― ― ― ― ― ― ― ― ― IOCB3 Y ―
C2IN2-
RB4 37 12 14 14 ANB4 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCB4 Y ―
ADACT
(1)

RB5 38 13 15 15 ANB5 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCB5 Y ―


RB6 39 14 16 16 ANB6 ― ― ― ― ― ― ― ― ― ― TX2 CLCIN2(1) ― IOCB6 Y ICSPCLK
CK2(1)
RB7 40 15 17 17 ANB7 ― ― ― DAC1OUT2 ― ― ― ― ― ― RX2 CLCIN3(1) ― IOCB7 Y ICSPDAT
DT2(1)
RC0 15 30 34 32 ANC0 ― ― ― ― SOSCO ― ― ― ― ― ― ― ― IOCC0 Y ―
T1CKI(1)
DS40001866B-page 11

RC1 16 31 35 35 ANC1 ― ― ― ― SOSCI CCP2(1) ― ― ― ― ― ― ― IOCC1 Y ―


RC2 17 32 36 36 ANC2 ― ― ― ― ― CCP1(1) ― ― ― ― ― ― ― IOCC2 Y ―
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.
TABLE 4: 40/44-PIN ALLOCATION TABLE (PIC16(L)F15375, PIC16(L)F15376) (CONTINUED)
 2016-2018 Microchip Technology Inc.

40-Pin UQFN

44-Pin TQFP

Comparator
40-Pin PDIP

44-Pin QFN

Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
PWM

CWG
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
RC3 18 33 37 37 ANC3 ― ― ― ― T2IN(1) ― ― ― SCL1 ― ― ― ― IOCC3 Y ―
SCK1(1,4)
RC4 23 38 42 42 ANC4 ― ― ― ― ― ― ― ― SDA1 ― ― ― ― IOCC4 Y ―
SDI1(1,4)
RC5 24 39 43 43 ANC5 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCC5 Y ―
RC6 25 40 44 44 ANC6 ― ― ― ― ― ― ― ― ― ― TX1 ― ― IOCC6 Y ―
CK1(1)
RC7 26 1 1 1 ANC7 ― ― ― ― ― ― ― ― ― ― RX1 ― ― IOCC7 Y ―
DT1(1)
RD0 19 34 38 38 AND0 ― ― ― ― ― ― ― ― SCK2, ― ― ― ― ― ― ―
SCL2(1,4)
RD1 20 35 39 39 AND1 ― ― ― ― ― ― ― ― SDA2, ― ― ― ― ― ― ―
SDI2(1,4)

PIC16(L)F15356/75/76/85/86
RD2 21 36 40 40 AND2 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RD3 22 37 41 41 AND3 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RD4 27 2 2 2 AND4 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RD5 28 3 3 3 AND5 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RD6 29 4 4 4 AND6 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RD7 30 5 5 5 AND7 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RE0 8 23 25 25 ANE0 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RE1 9 24 26 26 ANE1 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RE2 10 25 27 27 ANE2 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ―
RE3 1 16 18 18 ― ― ― ― ― ― ― ― ― ― ― ― ― ― IOCE3 Y MCLR
VPP
VDD 11 26 7 7 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VDD
VDD 32 7 28 28 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VDD
VSS 12 27 6 6 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
VSS 31 6 30 29 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options.
DS40001866B-page 12

3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.
TABLE 4: 40/44-PIN ALLOCATION TABLE (PIC16(L)F15375, PIC16(L)F15376) (CONTINUED)
 2016-2018 Microchip Technology Inc.

40-Pin UQFN

44-Pin TQFP

Comparator
40-Pin PDIP

44-Pin QFN

Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
PWM

CWG
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
OUT(2) ― ― ― ― ― ― C1OUT NCO1OUT ― TMR0 CCP1 PWM3OUT CWG1A SDO1 ― DT(3) CLC1OUT CLKR ― ― ―
CWG2A SDO2
― ― ― ― ― ― C2OUT ― ― ― CCP2 PWM4OUT CWG1B SCK1 ― CK1 CLC2OUT ― ― ― ―
CWG2B SCK2 CK2
― ― ― ― ― ― ― ― ― ― ― PWM5OUT CWG1C SCL1(3,4) ― TX1 CLC3OUT ― ― ― ―
CWG2C SCL2(3,4) TX2
― ― ― ― ― ― ― ― ― ― ― PWM6OUT CWG1D SDA1(3,4) ― ― CLC4OUT ― ― ― ―
CWG2D SDA2(3,4)
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 13
 2016-2018 Microchip Technology Inc.

TABLE 5: 48-Pin UQFN/TQFP 48-PIN ALLOCATION TABLE (PIC16(L)F15385, PIC16(L)F15386)

Comparator
Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
PWM

CWG
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
RA0 21 ANA0 ― C1IN0- ― ― ― ― ― ― ― ― ― CLCIN0(1) ― IOCA0 Y ―
C2IN0-
RA1 22 ANA1 ― C1IN1- ― ― ― ― ― ― ― ― ― CLCIN1(1) ― IOCA1 Y ―
C2IN1-
RA2 23 ANA2 ― C1IN0+ ― DAC1OUT1 ― ― ― ― ― ― ― ― ― IOCA2 Y ―
C2IN0+
RA3 24 ANA3 VREF+ C1IN1+ ― DACREF+ ― ― ― ― ― ― ― ― ― IOCA3 Y ―
RA4 25 ANA4 ― C1IN1- ― ― T0CKI(1) ― ― ― ― ― ― ― ― IOCA4 Y ―
RA5 26 ANA5 ― ― ― ― T1G(1) ― ― ― SS1(1) ― ― ― ― IOCA5 Y ―

PIC16(L)F15356/75/76/85/86
ADACT
RA6 33 ANA6 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA6 Y CLKOUT/
OSC1
RA7 32 ANA7 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCA7 Y CLKIN/
OSC2
RB0 8 ANB0 ― C2IN1+ ― ― ― ― ― CWG1(1) SS2(1) ZCD1 ― ― ― INT(1) Y ―
IOCB0
RB1 9 ANB1 ― C1IN3- ― ― ― ― ― ― SCL1 ― ― ― ― IOCB1 Y ―
C2IN3- SCK1(1,4)
RB2 10 ANB2 ― ― ― ― ― ― ― ― SDA1 ― ― ― ― IOCB2 Y ―
SDI1(1,4)
RB3 11 ANB3 ― C1IN2- ― ― ― ― ― ― ― ― ― ― ― IOCB3 Y ―
C2IN2-
RB4 16 ANB4 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCB4 Y ―
ADACT(1)
RB5 17 ANB5 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCB5 Y ―
RB6 18 ANB6 ― ― ― ― ― ― ― ― ― ― TX2 CLCIN2(1) ― IOCB6 Y ICSPCLK
CK2(1)
RB7 19 ANB7 ― ― ― DAC1OUT2 ― ― ― ― ― ― RX2 CLCIN3(1) ― IOCB7 Y ICSPDAT
DT2(1)
DS40001866B-page 14

RC0 34 ANC0 ― ― ― ― SOSCO ― ― ― ― ― ― ― ― IOCC0 Y ―


T1CKI(1)
RC1 35 ANC1 ― ― ― ― SOSCI CCP2(1) ― ― ― ― ― ― ― IOCC1 Y ―
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.
TABLE 5: 48-PIN ALLOCATION TABLE (PIC16(L)F15385, PIC16(L)F15386) (CONTINUED)
 2016-2018 Microchip Technology Inc.

48-Pin UQFN/TQFP

Comparator
Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
PWM

CWG
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
RC2 40 ANC2 ― ― ― ― ― CCP1(1) ― ― ― ― ― ― ― IOCC2 Y ―
RC3 41 ANC3 ― ― ― ― T2IN(1) ― ― ― SCL1 ― ― ― ― IOCC3 Y ―
SCL2(1,4)
RC4 46 ANC4 ― ― ― ― ― ― ― ― SDA1 ― ― ― ― IOCC4 Y ―
SDI1(1,4)
RC5 47 ANC5 ― ― ― ― ― ― ― ― ― ― ― ― ― IOCC5 Y ―
RC6 48 ANC6 ― ― ― ― ― ― ― ― ― ― TX1 ― ― IOCC6 Y ―
CK1(1)
RC7 1 ANC7 ― ― ― ― ― ― ― ― ― ― RX1 ― ― IOCC7 Y ―
DT1(1)

PIC16(L)F15356/75/76/85/86
RD0 42 AND0 ― ― ― ― ― ― ― ― SCK2 ― ― ― ― ― Y ―
SCL2(1,4)
RD1 43 AND1 ― ― ― ― ― ― ― ― SDA2 ― ― ― ― ― Y ―
SDI2(1,4)
RD2 44 AND2 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RD3 45 AND3 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RD4 2 AND4 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RD5 3 AND5 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RD6 4 AND6 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RD7 5 AND7 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RE0 27 ANE0 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RE1 28 ANE1 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RE2 29 ANE2 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RE3 20 ― ― ― ― ― ― ― ― ― ― ― ― ― ― IOCE3 Y MCLR
VPP
RF0 36 ANF0 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RF1 37 ANF1 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RF2 38 ANF2 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
DS40001866B-page 15

RF3 39 ANF3 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RF4 12 ANF4 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.
TABLE 5: 48-PIN ALLOCATION TABLE (PIC16(L)F15385, PIC16(L)F15386) (CONTINUED)
 2016-2018 Microchip Technology Inc.

48-Pin UQFN/TQFP

Comparator
Reference

EUSART

Interrupt

Pull-up
Timers

MSSP

CLKR

Basic
PWM

CWG
I/O(2)

NCO
ADC

DAC

CCP

ZCD

CLC
RF5 13 ANF5 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RF6 14 ANF6 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
RF7 15 ANF7 ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y ―
VDD 30 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― Y VDD
VDD 7 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VDD
VSS 6 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
VSS 31 ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― ― VSS
OUT(2) ― ― ― C1OUT NCO1OUT ― TMR0 CCP1 PWM3OUT CWG1A SDO1 ― DT(3) CLC1OUT CLKR ― ― ―
CWG2A SDO2

PIC16(L)F15356/75/76/85/86
― ― ― C2OUT ― ― ― CCP2 PWM4OUT CWG1B SCK1 ― CK1 CLC2OUT ― ― ― ―
CWG2B SCK2 CK2
― ― ― ― ― ― ― ― PWM5OUT CWG1C SCK1(3,4) ― TX1 CLC3OUT ― ― ― ―
CWG2C SCL2(3,4) TX2
― ― ― ― ― ― ― ― PWM6OUT CWG1D SDA1(3,4) ― ― CLC4OUT ― ― ― ―
CWG2D SDA2(3,4)
Note 1: This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins.
2: All digital output signals shown in this row are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers.
4: These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or
SMBUS input buffer thresholds.
DS40001866B-page 16
PIC16(L)F15356/75/76/85/86
Table of Contents
1.0 Device Overview ........................................................................................................................................................................... 19
2.0 Guidelines for Getting Started with PIC16(L)F15354/55 Microcontrollers .................................................................................... 43
3.0 Enhanced Mid-Range CPU........................................................................................................................................................... 46
4.0 Memory Organization .................................................................................................................................................................... 48
5.0 Device Configuration ................................................................................................................................................................... 101
6.0 Device Information Area ............................................................................................................................................................. 112
7.0 Device Configuration Information ................................................................................................................................................ 114
8.0 Resets ......................................................................................................................................................................................... 115
9.0 Oscillator Module (with Fail-Safe Clock Monitor) ........................................................................................................................ 126
10.0 Interrupts ................................................................................................................................................................................... 143
11.0 Power-Saving Operation Modes ............................................................................................................................................... 165
12.0 Windowed Watchdog Timer (WWDT) ....................................................................................................................................... 172
13.0 Nonvolatile Memory (NVM) Control .......................................................................................................................................... 180
14.0 /O Ports ..................................................................................................................................................................................... 198
15.0 Peripheral Pin Select (PPS) Module ......................................................................................................................................... 233
16.0 Peripheral Module Disable ........................................................................................................................................................ 246
17.0 Interrupt-On-Change ................................................................................................................................................................. 254
18.0 Fixed Voltage Reference (FVR) ................................................................................................................................................ 264
19.0 Temperature Indicator Module .................................................................................................................................................. 267
20.0 Analog-to-Digital Converter (ADC) Module ............................................................................................................................... 269
21.0 5-Bit Digital-to-Analog Converter (DAC1) Module ..................................................................................................................... 285
22.0 Numerically Controlled Oscillator (NCO) Module ...................................................................................................................... 290
23.0 Comparator Module .................................................................................................................................................................. 300
24.0 Zero-Cross Detection (ZCD) Module ........................................................................................................................................ 310
25.0 Timer0 Module .......................................................................................................................................................................... 316
26.0 Timer1 Module with Gate Control ............................................................................................................................................. 322
27.0 Timer2 Module With Hardware Limit Timer (HLT) .................................................................................................................... 336
28.0 Capture/Compare/PWM Modules ............................................................................................................................................. 357
29.0 Pulse-Width Modulation (PWM) ................................................................................................................................................ 368
30.0 Complementary Waveform Generator (CWG) Module ............................................................................................................. 375
31.0 Configurable Logic Cell (CLC) .................................................................................................................................................. 400
32.0 Master Synchronous Serial Port (MSSPx) Modules ................................................................................................................. 417
33.0 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) ................................................................ 468
34.0 Reference Clock Output Module ............................................................................................................................................... 496
35.0 In-Circuit Serial Programming™ (ICSP™) ................................................................................................................................ 500
36.0 Instruction Set Summary........................................................................................................................................................... 502
37.0 Electrical Specifications ............................................................................................................................................................ 515
38.0 DC and AC Characteristics Graphs and Charts ........................................................................................................................ 544
39.0 Development Support ............................................................................................................................................................... 564
40.0 Packaging Information .............................................................................................................................................................. 568

 2016-2018 Microchip Technology Inc. DS40001866B-page 17


PIC16(L)F15356/75/76/85/86

TO OUR VALUED CUSTOMERS


It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com. We welcome your feedback.

Most Current Data Sheet


To obtain the most up-to-date version of this data sheet, please register at our Worldwide Website at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000).

Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Website; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.

Customer Notification System


Register on our website at www.microchip.com to receive the most current information on all of our products.

 2016-2018 Microchip Technology Inc. DS40001866B-page 18


PIC16(L)F15356/75/76/85/86
1.0 DEVICE OVERVIEW
TABLE 1-1: DEVICE PERIPHERAL
The PIC16(L)F15356/75/76/85/86 are described within
SUMMARY
this data sheet. The PIC16(L)F15356/75/76/85/86

PIC16(L)F15356/75/76/85/86
devices are available in 28/40/44/48-pin SPDIP, SSOP,
SOIC, TQFP, QFN and UQFN packages. Figure 1-1,
Figure 1-2 and Figure 1-3 shows the block diagrams of
the PIC16(L)F15356/75/76/85/86 devices. Table 1-2
through Table 1-4 shows the pinout descriptions. Peripheral
Reference Table 1-1 for peripherals available per device.

Analog-to-Digital Converter ●
Digital-to-Analog Converter (DAC1) ●
Fixed Voltage Reference (FVR) ●
Numerically Controlled Oscillator (NCO1) ●
Temperature Indicator Module (TIM) ●
Zero-Cross Detect (ZCD1) ●
Capture/Compare/PWM Modules (CCP)
CCP1 ●
CCP2 ●
Comparator Module (Cx)
C1 ●
C2 ●
Configurable Logic Cell (CLC)
CLC1 ●
CLC2 ●
CLC3 ●
CLC4 ●
Complementary Waveform Generator (CWG)
CWG1 ●
Enhanced Universal Synchronous/Asynchronous
Receiver/Transmitter (EUSART)
EUSART1 ●
EUSART2 ●
Master Synchronous Serial Ports (MSSP)
MSSP1 ●
MSSP2 ●
Pulse-Width Modulator (PWM)
PWM3 ●
PWM4 ●
PWM5 ●
PWM6 ●
Timers
Timer0 ●
Timer1 ●
Timer2 ●

 2016-2018 Microchip Technology Inc. DS40001866B-page 19


PIC16(L)F15356/75/76/85/86
1.1 Register and Bit Naming 1.1.2.3 Bit Fields
Conventions Bit fields are two or more adjacent bits in the same
register. Bit fields adhere only to the short bit naming
1.1.1 REGISTER NAMES convention. For example, the three Least Significant
When there are multiple instances of the same bits of the COG1CON0 register contain the mode
peripheral in a device, the peripheral control registers control bits. The short name for this field is MD. There
will be depicted as the concatenation of a peripheral is no long bit name variant. Bit field access is only
identifier, peripheral instance, and control identifier. possible in C programs. The following example
The control registers section will show just one demonstrates a C program instruction for setting the
instance of all the register names with an ‘x’ in the place COG1 to the Push-Pull mode:
of the peripheral instance number. This naming COG1CON0bits.MD = 0x5;
convention may also be applied to peripherals when
Individual bits in a bit field can also be accessed with
there is only one instance of that peripheral in the
long and short bit names. Each bit is the field name
device to maintain compatibility with other devices in
appended with the number of the bit position within the
the family that contain more than one.
field. For example, the Most Significant mode bit has
1.1.2 BIT NAMES the short bit name MD2 and the long bit name is
G1MD2. The following two examples demonstrate
There are two variants for bit names: assembly program sequences for setting the COG1 to
• Short name: Bit function abbreviation Push-Pull mode:
• Long name: Peripheral abbreviation + short name Example 1:
MOVLW ~(1<<G1MD1)
1.1.2.1 Short Bit Names ANDWF COG1CON0,F
Short bit names are an abbreviation for the bit function. MOVLW 1<<G1MD2 | 1<<G1MD0
For example, some peripherals are enabled with the IORWF COG1CON0,F
EN bit. The bit names shown in the registers are the Example 2:
short name variant.
BSF COG1CON0,G1MD2
Short bit names are useful when accessing bits in C BCF COG1CON0,G1MD1
programs. The general format for accessing bits by the BSF COG1CON0,G1MD0
short name is RegisterNamebits.ShortName. For
example, the enable bit, EN, in the COG1CON0 regis- 1.1.3 REGISTER AND BIT NAMING
ter can be set in C programs with the instruction EXCEPTIONS
COG1CON0bits.EN = 1.
1.1.3.1 Status, Interrupt, and Mirror Bits
Short names are generally not useful in assembly
programs because the same name may be used by Status, interrupt enables, interrupt flags, and mirror bits
different peripherals in different bit positions. When this are contained in registers that span more than one
occurs, during the include file generation, all instances peripheral. In these cases, the bit name shown is
of that short bit name are appended with an underscore unique so there is no prefix or short name variant.
plus the name of the register in which the bit resides to
avoid naming contentions. 1.1.3.2 Legacy Peripherals
There are some peripherals that do not strictly adhere
1.1.2.2 Long Bit Names to these naming conventions. Peripherals that have
Long bit names are constructed by adding a peripheral existed for many years and are present in almost every
abbreviation prefix to the short name. The prefix is device are the exceptions. These exceptions were
unique to the peripheral thereby making every long bit necessary to limit the adverse impact of the new
name unique. The long bit name for the COG1 enable conventions on legacy code. Peripherals that do
bit is the COG1 prefix, G1, appended with the enable adhere to the new convention will include a table in the
bit short name, EN, resulting in the unique bit name registers section indicating the long name prefix for
G1EN. each peripheral instance. Peripherals that fall into the
exception category will not have this table. These
Long bit names are useful in both C and assembly pro-
peripherals include, but are not limited to, the following:
grams. For example, in C the COG1CON0 enable bit
can be set with the G1EN = 1 instruction. In assembly, • EUSART
this bit can be set with the BSF COG1CON0,G1EN • MSSP
instruction.

 2016-2018 Microchip Technology Inc. DS40001866B-page 20


 2016-2018 Microchip Technology Inc.

FIGURE 1-1: PIC16(L)F15356 BLOCK DIAGRAM

Rev. 10-000039L
Program 1/13/2017

Flash Memory
RAM

PORTA
Timing
Generation

PORTB
CLKOUT
EXTOSC
Oscillator
CPU
CLKIN
PORTC

(Note 3)

PIC16(L)F15356/75/76/85/86
SOSCIN/ Secondary
SOSCI Oscillator
(SOSC)
SOSCO
PORTE
MCLR

ADC
PWM6 PWM5 PWM4 PWM3 Timer2 Timer1 Timer0 C2 C1 TIM DAC FVR
10-bit

CWG1 NCO1 EUSART1 EUSART2 MSSP2 MSSP1 CLC4 CLC3 CLC2 CLC1 ZCD1 CCP1 CCP2
DS40001866B-page 21

Note 1: See applicable chapters for more information on peripherals.


2: See Table 1-1 for peripherals available on specific devices.
3: See Figure 3-1.
 2016-2018 Microchip Technology Inc.

FIGURE 1-2: PIC16(L)F15375/76 BLOCK DIAGRAM

Rev. 10-000039M
Program 1/13/2017

Flash Memory
RAM

PORTA
Timing
Generation

PORTB
CLKOUT
EXTOSC
Oscillator
CPU
CLKIN
PORTC

(Note 3)

PIC16(L)F15356/75/76/85/86
SOSCIN/ Secondary PORTD
SOSCI Oscillator
(SOSC)
SOSCO
PORTE
MCLR

ADC
PWM6 PWM5 PWM4 PWM3 Timer2 Timer1 Timer0 C2 C1 TIM DAC FVR
10-bit

CWG1 NCO1 EUSART1 EUSART2 MSSP2 MSSP1 CLC4 CLC3 CLC2 CLC1 ZCD1 CCP1 CCP2
DS40001866B-page 22

Note 1: See applicable chapters for more information on peripherals.


2: See Table 1-1 for peripherals available on specific devices.
3: See Figure 3-1.
 2016-2018 Microchip Technology Inc.

FIGURE 1-3: PIC16(L)F15385/86 BLOCK DIAGRAM

Rev. 10-000039N
Program 1/13/2017

Flash Memory
RAM

PORTA
Timing
Generation

PORTB
CLKOUT
EXTOSC
Oscillator
CPU
CLKIN
PORTC

PIC16(L)F15356/75/76/85/86
(Note 3)
SOSCIN/ Secondary PORTD
SOSCI Oscillator
(SOSC)
SOSCO
PORTE
MCLR

PORTF

ADC
PWM6 PWM5 PWM4 PWM3 Timer2 Timer1 Timer0 C2 C1 TIM DAC FVR
10-bit

CWG1 NCO1 EUSART1 EUSART2 MSSP2 MSSP1 CLC4 CLC3 CLC2 CLC1 ZCD1 CCP1 CCP2
DS40001866B-page 23

Note 1: See applicable chapters for more information on peripherals.


2: See Table 1-1 for peripherals available on specific devices.
3: See Figure 3-1.
PIC16(L)F15356/75/76/85/86

TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION


Input
Name Function Output Type Description
Type

RA0/ANA0/C1IN0-/C2IN0-/CLCIN0(1)/ RA0 TTL/ST CMOS/OD General purpose I/O.


IOCA0
ANA0 AN — ADC Channel A0 input.

C1IN0- AN — Comparator 1 negative input.

C2IN0- AN — Comparator 2 negative input.

CLCIN0(1) TTL/ST — Configurable Logic Cell source input.

IOCA0 TTL/ST — Interrupt-on-change input.


RA1/ANA1/C1IN1-/C2IN1-/CLCIN1(1)/ RA1 TTL/ST CMOS/OD General purpose I/O.
IOCA1
ANA1 AN — ADC Channel A1 input.

C1IN1- AN — Comparator 1 negative input.

C2IN1- AN — Comparator 2 negative input.

CLCIN1(1) TTL/ST — Configurable Logic Cell source input.

IOCA1 TTL/ST — Interrupt-on-change input.


RA2/ANA2/C1IN0+/C2IN0+/ RA2 TTL/ST CMOS/OD General purpose I/O.
DAC1OUT1/IOCA2
ANA2 AN — ADC Channel A2 input.

C1IN0+ AN — Comparator 2 positive input.

C2IN0+ AN — Comparator 2 positive input.

DAC1OUT1 — AN Digital-to-Analog Converter output.

IOCA2 TTL/ST — Interrupt-on-change input.


RA3/ANA3/C1IN1+/VREF+/IOCA3/ RA3 TTL/ST CMOS/OD General purpose I/O.
DAC1REF+
ANA3 AN — ADC Channel A3 input.

C1IN1+ AN — Comparator 1 positive input.

VREF+ AN — External ADC and/or DAC positive reference input.

IOCA3 TTL/ST — Interrupt-on-change input.

DAC1REF+ TTL/ST AN DAC positive reference.


RA4/ANA4/T0CKI(1)/IOCA4 RA4 TTL/ST CMOS/OD General purpose I/O.

ANA4 AN — ADC Channel A4 input.

T0CKI(1) TTL/ST — Timer0 clock input.

IOCA4 TTL/ST — Interrupt-on-change input.


RA5/ANA5/SS1(1)/IOCA5 RA5 TTL/ST CMOS/OD General purpose I/O.

ANA5 AN — ADC Channel A5 input.

SS1(1) TTL/ST — MSSP1 SPI slave select input.

IOCA5 TTL/ST — Interrupt-on-change input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 24


PIC16(L)F15356/75/76/85/86
TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION (CONTINUED)
Input
Name Function Output Type Description
Type

RA6/ANA6/OSC2/CLKOUT/IOCA6 RA6 TTL/ST CMOS/OD General purpose I/O.

ANA6 AN — ADC Channel A6 input.


External Crystal/Resonator (LP, XT, HS modes) driver
OSC2 — XTAL
output.
CLKOUT — CMOS/OD FOSC/4 digital output (in non-crystal/resonator modes).

IOCA6 TTL/ST — Interrupt-on-change input.


RA7/ANA7/OSC1/CLKIN/IOCA7 RA7 TTL/ST CMOS/OD General purpose I/O.

ANA7 AN — ADC Channel A7 input.

OSC1 XTAL — External Crystal/Resonator (LP, XT, HS modes) driver input.

CLKIN TTL/ST — External digital clock input.

IOCA7 TTL/ST — Interrupt-on-change input.


RB0/ANB0/C2IN1+/ZCD1/SS2(1)/ RB0 TTL/ST CMOS/OD General purpose I/O.
CWG1IN(1)/INT(1)/IOCB0
ANB0 AN — ADC Channel B0 input.

C2IN1+ AN — Comparator 2 positive input.


Zero-cross detect input pin (with constant current sink/
ZCD1 AN AN
source).
SS2(1) TTL/ST — MSSP2 SPI slave select input.
(1)
CWG1IN TTL/ST — Complementary Waveform Generator 1 input.

INT(1) TTL/ST — External interrupt request input.

IOCB0 TTL/ST — Interrupt-on-change input.


RB1/ANB1/C1IN3-/C2IN3-/SCL2(3,4)/ RB1 TTL/ST CMOS/OD General purpose I/O.
SCK2(1)/IOCB1
ANB1 AN — ADC Channel B1 input.

C1IN3- AN — Comparator 1 negative input.

C2IN3- AN — Comparator 2 negative input.

SCL2(3,4) I2C OD MSSP2 I2C clock input/output.


MSSP2 SPI serial clock (default input location, SCK2 is a
SCK2(1) TTL/ST CMOS/OD
PPS remappable input and output).
IOCB1 TTL/ST — Interrupt-on-change input.
RB2/ANB2/SDA2(3,4)/SDI2(1)/IOCB2 RB2 TTL/ST CMOS/OD General purpose I/O.

ANB2 AN — ADC Channel B2 input.


(3,4) 2
SDA2 I C OD MSSP2 I2C serial data input/output.

SDI2(1) TTL/ST — MSSP2 SPI serial data input.

IOCB2 TTL/ST — Interrupt-on-change input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 25


PIC16(L)F15356/75/76/85/86
TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION (CONTINUED)
Input
Name Function Output Type Description
Type

RB3/ANB3/C1IN2-/C2IN2-/IOCB3 RB3 TTL/ST CMOS/OD General purpose I/O.

ANB3 AN — ADC Channel B3 input.

C1IN2- AN — Comparator 1 negative input.

C2IN2- AN — Comparator 2 negative input.

IOCB3 TTL/ST — Interrupt-on-change input.


(1)
RB4/ANB4/ADACT /IOCB4 RB4 TTL/ST CMOS/OD General purpose I/O.

ANB4 AN — ADC Channel B4 input.

ADACT(1) TTL/ST — ADC Auto-Conversion Trigger input.

IOCB4 TTL/ST — Interrupt-on-change input.


RB5/ANB5/T1G(1)/IOCB5 RB5 TTL/ST CMOS/OD General purpose I/O.

ANB5 AN — ADC Channel B5 input.


(1)
T1G ST — Timer1 Gate input.

IOCB5 TTL/ST — Interrupt-on-change input.


RB6/ANB6/CLCIN2(1)/IOCB6/TX2/ RB6 TTL/ST CMOS/OD General purpose I/O.
(3)
CK2 /ICSPCLK
ANB6 AN — ADC Channel B6 input.

CLCIN2(1) TTL/ST — Configurable Logic Cell source input.

IOCB6 TTL/ST — Interrupt-on-change input.

TX2 — CMOS EUSART2 asynchronous.

CK2(3) TTL/ST CMOS/OD EUSART2 synchronous mode clock input/output.

ICSPCLK ST — In-Circuit Serial Programming™ and debugging clock input.


RB7/ANB7/RX2/DT2/CLCIN3(1)/ RB7 TTL/ST CMOS/OD General purpose I/O.
IOCB7/DAC1OUT2/ICSPDAT
ANB7 AN — ADC Channel B7 input.

CLCIN3(1) TTL/ST — Configurable Logic Cell source input.

IOCB7 TTL/ST — Interrupt-on-change input.


(1)
RX2 TTL/ST — EUSART2 Asynchronous mode receiver data input.

DT2(3) TTL/ST CMOS/OD EUSART2 Synchronous mode data input/output.

DAC1OUT2 — AN Digital-to-Analog Converter output.


In-Circuit Serial Programming™ and debugging data input/
ICSPDAT ST CMOS
output.
RC0/ANC0/T1CKI(1)/IOCC0/SOSCO RC0 TTL/ST CMOS/OD General purpose I/O.

ANC0 AN — ADC Channel C0 input.

T1CKI(1) TTL/ST — Timer1 external digital clock input.

IOCC0 TTL/ST — Interrupt-on-change input.

SOSCO — AN 32.768 kHz secondary oscillator crystal driver output.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 26


PIC16(L)F15356/75/76/85/86
TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION (CONTINUED)
Input
Name Function Output Type Description
Type

RC1/ANC1/CCP2(1)/IOCC1/SOSCI RC1 TTL/ST CMOS/OD General purpose I/O.

ANC1 AN — ADC Channel C1 input.

CCP2(1) TTL/ST CMOS/OD CCP2 Capture Input.

IOCC1 TTL/ST — Interrupt-on-change input.

SOSCI AN — 32.768 kHz secondary oscillator crystal driver input.


RC2/ANC2/CCP1(1)/IOCC2 RC2 TTL/ST CMOS/OD General purpose I/O.

ANC2 AN — ADC Channel C2 input.

CCP1(1) TTL/ST CMOS/OD CCP1 Capture Input.

IOCC2 TTL/ST — Interrupt-on-change input.


RC3/ANC3/SCL1(3,4)/SCK1(1)/T2IN(1)/ RC3 TTL/ST CMOS/OD General purpose I/O.
IOCC3
ANC3 AN — ADC Channel C3 input.
(3,4) 2
SCL1 I C OD MSSP1 I2C input/output.
MSSP1 SPI clock input/output (default input location, SCK1
SCK1(1) TTL/ST CMOS/OD
is a PPS remappable input and output).
T2IN(1) TTL/ST — Timer2 external input.

IOCC3 TTL/ST — Interrupt-on-change input.


RC4/ANC4/SDA1(3,4)/SDI1(1)/IOCC4 RC4 TTL/ST CMOS/OD General purpose I/O.

ANC4 AN — ADC Channel C4 input.


(3,4) 2
SDA1 I C OD MSSP1 I2C serial data input/output.

SDI1(1) TTL/ST — MSSP1 SPI serial data input.

IOCC4 TTL/ST — Interrupt-on-change input.


RC5/ANC5/IOCC5 RC5 TTL/ST CMOS/OD General purpose I/O.

ANC5 AN — ADC Channel C5 input.

IOCC5 TTL/ST — Interrupt-on-change input.


RC6/ANC6/TX1/CK1(1)/IOCC6 RC6 TTL/ST CMOS/OD General purpose I/O.

ANC6 AN — ADC Channel C6 input.

TX1 — CMOS EUSART1 asynchronous transmit.

CK1(1) TTL/ST CMOS/OD EUSART 1 synchronous mode clock input/output.

IOCC6 TTL/ST — Interrupt-on-change input.


RC7/ANC7/RX1/DT1(3)/IOCC7 RC7 TTL/ST CMOS/OD General purpose I/O.

ANC7 AN — ADC Channel C7 input.

RX1 TTL/ST — EUSART1 Asynchronous mode receiver data input.

DT1(3) TTL/ST CMOS/OD EUSART1 Synchronous mode data input/output.

IOCC7 TTL/ST — Interrupt-on-change input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 27


PIC16(L)F15356/75/76/85/86
TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION (CONTINUED)
Input
Name Function Output Type Description
Type

RE3/IOCE3/MCLR/VPP General purpose input only (when MCLR is disabled by the


RE3 TTL/ST —
Configuration bit).
IOCE3 TTL/ST — Interrupt-on-change input.

MCLR ST — Master clear input with internal weak pull-up resistor.

VPP HV — ICSP™ High-Voltage Programming mode entry input.


VDD VDD Power — Positive supply voltage input.
VSS VSS Power — Ground reference.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 28


PIC16(L)F15356/75/76/85/86
TABLE 1-2: PIC16(L)F15356 PINOUT DESCRIPTION (CONTINUED)
Input
Name Function Output Type Description
Type

OUT(2) C1OUT — CMOS/OD Comparator 1 output.

C2OUT — CMOS/OD Comparator 2 output.

SDO1 — CMOS/OD MSSP1 SPI serial data output.

SCK1 — CMOS/OD MSSP1 SPI serial clock output.

SDO2 — CMOS/OD MSSP2 SPI serial data output.

SCK2 — CMOS/OD MSSP2 SPI serial clock output.

TX1 — CMOS/OD EUSART1 Asynchronous mode transmitter data output.

CK1(3) — CMOS/OD EUSART1 Synchronous mode clock output.

TX2 — CMOS/OD EUSART2 Asynchronous mode transmitter data output.

CK2(3) — CMOS/OD EUSART2 Synchronous mode clock output.

DT(3) — CMOS/OD EUSART Synchronous mode data output.

TMR0 — CMOS/OD Timer0 output.

CCP1 — CMOS/OD CCP2 output (compare/PWM functions).

CCP2 — CMOS/OD CCP2 output (compare/PWM functions).

PWM3OUT — CMOS/OD PWM3 output.

PWM4OUT — CMOS/OD PWM4 output.

PWM5OUT — CMOS/OD PWM5 output.

PWM6OUT — CMOS/OD PWM6 output.

CWG1A — CMOS/OD Complementary Waveform Generator 1 output A.

CWG1B — CMOS/OD Complementary Waveform Generator 1 output B.

CWG1C — CMOS/OD Complementary Waveform Generator 1 output C.

CWG1D — CMOS/OD Complementary Waveform Generator 1 output D.

CLC1OUT — CMOS/OD Configurable Logic Cell 1 output.

CLC2OUT — CMOS/OD Configurable Logic Cell 2 output.

CLC3OUT — CMOS/OD Configurable Logic Cell 3 output.

CLC4OUT — CMOS/OD Configurable Logic Cell 4 output.

NCO1OUT — CMOS/OD Numerically Controller Oscillator output.

CLKR — CMOS/OD Clock Reference module output.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-1 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin
options as described in Table 15-3.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 29


PIC16(L)F15356/75/76/85/86

TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION


Name Input
Function Output Type Description
Type

RA0/ANA0/C1IN0-/C2IN0-/CLCIN0(1)/ RA0 TTL/ST CMOS/OD General purpose I/O.


IOCA0
ANA0 AN — ADC Channel A0 input.

C1IN0- AN — Comparator negative input.

C2IN0- AN — Comparator negative input.

CLCIN0(1) TTL/ST — Configurable Logic Cell source input.

IOCA0 TTL/ST — Interrupt-on-change input.


RA1/ANA1/C1IN1-/C2IN1-/CLCIN1(1)/ RA1 TTL/ST CMOS/OD General purpose I/O.
IOCA1
ANA1 AN — ADC Channel A1 input.

C1IN1- AN — Comparator negative input.

C2IN1- AN — Comparator negative input.

CLCIN1(1) TTL/ST — Configurable Logic Cell source input.

IOCA1 TTL/ST — Interrupt-on-change input.


RA2/ANA2/C1IN0+/C2IN0+/ RA2 TTL/ST CMOS/OD General purpose I/O.
DAC1OUT1/IOCA2
ANA2 AN — ADC Channel A2 input.

C1IN0+ AN — Comparator positive input.

C2IN0+ AN — Comparator positive input.

DAC1OUT1 — AN Digital-to-Analog Converter output.

IOCA2 TTL/ST — Interrupt-on-change input.


RA3/ANA3/C1IN1+/VREF+/DACREF+/ RA3 TTL/ST CMOS/OD General purpose I/O.
IOCA3
ANA3 AN — ADC Channel A3 input.

C1IN1+ AN — Comparator positive input.

VREF+ AN — External ADC and/or DAC positive reference input.

IOCA3 TTL/ST — Interrupt-on-change input.


RA4/ANA4/T0CKI(1)/IOCA4 RA4 TTL/ST CMOS/OD General purpose I/O.

ANA4 AN — ADC Channel A4 input.

T0CKI(1) TTL/ST — Timer0 clock input.

IOCA4 TTL/ST — Interrupt-on-change input.


RA5/ANA5/SS1(1)/T1G(1)/IOCA5 RA5 TTL/ST CMOS/OD General purpose I/O.

ANA5 AN — ADC Channel A5 input.

SS1(1) TTL/ST — MSSP1 SPI slave select input.


(1)
T1G TTL/ST — Timer1 gate input.

IOCA5 TTL/ST — Interrupt-on-change input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 30


PIC16(L)F15356/75/76/85/86
TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RA6/ANA6/CLKOUT/IOCA6/OSC1 RA6 TTL/ST CMOS/OD General purpose I/O.

ANA6 AN — ADC Channel A6 input.

CLKOUT — CMOS/OD FOSC/4 digital output (in non-crystal/resonator modes).

IOCA6 TTL/ST — Interrupt-on-change input.

OSC1 XTAL — External Crystal/Resonator (LP, XT, HS modes) driver input.


RA7/ANA7/CLKIN/IOCA7/OSC2 RA7 TTL/ST CMOS/OD General purpose I/O.

ANA7 AN — ADC Channel A7 input.

CLKIN TTL/ST — External digital clock input.

IOCA7 TTL/ST — Interrupt-on-change input.

OSC2 — XTAL External Crystal/Resonator (LP, XT, HS modes) driver output.


RB0/ANB0/C2IN1+/ZCD1/SS2(1)/ RB0 TTL/ST CMOS/OD General purpose I/O.
CWG1(1)/INT(1)/IOCB0
ANB0 AN — ADC Channel B0 input.

C2IN1+ AN — Comparator positive input.

ZCD1 AN AN Zero-cross detect input pin (with constant current sink/source).

SS2(1) TTL/ST — MSSP2 SPI slave select input.


(1)
CWG1 TTL/ST — Complementary Waveform Generator 1 input.

INT(1) TTL/ST — External interrupt request input.

IOCB0 TTL/ST — Interrupt-on-change input.


RB1/ANB1/C1IN3-/C2IN3-/ RB1 TTL/ST CMOS/OD General purpose I/O.
SCL1(1)/SCK1(1)/IOCB1
ANB1 AN — ADC Channel B1 input.

C1IN3- AN — Comparator negative input.

C2IN3- AN — Comparator negative input.

SCL1(1) I2C OD MSSP1 I2C input/output.


MSSP1 SPI clock input/output (default input location, SCK1 is a
SCK1(1) TTL/ST CMOS/OD
PPS remappable input and output).
IOCB1 TTL/ST — Interrupt-on-change input.
RB2/ANB2/SDA1(1)/SDI1(1)/IOCB2 RB2 TTL/ST CMOS/OD General purpose I/O.

ANB2 AN — ADC Channel B2 input.

SDA1(1) I2C OD MSSP1 I2C serial data input/output.


MSSP1 SPI serial data input (default input location, SDI1 is a
SDI1(1) TTL/ST —
PPS remappable input and output).
IOCB2 TTL/ST — Interrupt-on-change input.
RB3/ANB3/C1IN2-/C2IN2-/IOCB3 RB3 TTL/ST CMOS/OD General purpose I/O.

ANB3 AN — ADC Channel B3 input.

C1IN2- AN — Comparator negative input.

C2IN2- AN — Comparator negative input.

IOCB3 TTL/ST — Interrupt-on-change input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 31


PIC16(L)F15356/75/76/85/86
TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RB4/ANB4/ADACT(1)/IOCB4 RB4 TTL/ST CMOS/OD General purpose I/O.

ANB4 AN — ADC Channel B4 input.


(1)
ADACT TTL/ST — ADC Auto-Conversion Trigger input.

IOCB4 TTL/ST — Interrupt-on-change input.


RB5/ANB5/IOCB5 RB5 TTL/ST CMOS/OD General purpose I/O.

ANB5 AN — ADC Channel B5 input.

IOCB5 TTL/ST — Interrupt-on-change input.


RB6/ANB6/CLCIN2(1)/TX2/CK2(1)/ RB6 TTL/ST CMOS/OD General purpose I/O.
IOCB6/ICSPCLK
ANB6 AN — ADC Channel B6 input.

CLCIN2(1) TTL/ST — Configurable Logic Cell source input.

TX2 TTL/ST — EUSART2 Asynchronous mode receiver data input.


(1)
CK2 TTL/ST CMOS/OD EUSART2 Synchronous mode clock input/output.

IOCB6 TTL/ST — Interrupt-on-change input.

ICSPCLK ST — In-Circuit Serial Programming™ and debugging clock input.


RB7/ANB7/DAC1OUT2/CLCIN3(1)/ RB7 TTL/ST CMOS/OD General purpose I/O.
RX2/DT2(1)/IOCB7/ICSPDAT
ANB7 AN — ADC Channel B7 input.

DAC1OUT2 — AN Digital-to-Analog Converter output.

CLCIN3(1) TTL/ST — Configurable Logic Cell source input.

RX2 TTL/ST — EUSART2 Asynchronous mode receiver data input.

DT2 TTL/ST CMOS/OD EUSART2 Synchronous mode data input/output.

IOCB7 TTL/ST — Interrupt-on-change input.


In-Circuit Serial Programming™ and debugging data input/out-
ICSPDAT ST CMOS
put.
RC0/ANC0/T1CKI(1)/IOCC0/SOSCO RC0 TTL/ST CMOS/OD General purpose I/O.

ANC0 AN — ADC Channel C0 input.

T1CKI(1) TTL/ST — Timer1 external digital clock input.

IOCC0 TTL/ST — Interrupt-on-change input.

SOSCO — AN 32.768 kHz secondary oscillator crystal driver output.


RC1/ANC1/CCP2(1)/IOCC1/SOSCI RC1 TTL/ST CMOS/OD General purpose I/O.

ANC1 AN — ADC Channel C1 input.

(1) Capture/compare/PWM2 (default input location for capture


CCP2 TTL/ST CMOS/OD
function).
IOCC1 TTL/ST — Interrupt-on-change input.

SOSCI AN — 32.768 kHz secondary oscillator crystal driver input.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 32


PIC16(L)F15356/75/76/85/86
TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RC2/ANC2/CCP1(1)/IOCC2 RC2 TTL/ST CMOS/OD General purpose I/O.

ANC2 AN — ADC Channel C2 input.


Capture/compare/PWM1 (default input location for capture
CCP1(1) TTL/ST CMOS/OD
function).
IOCC2 TTL/ST — Interrupt-on-change input.
RC3/ANC3/SCL1(1)/SDI1(1)/T2IN(1)/ RC3 TTL/ST CMOS/OD General purpose I/O.
IOCC3
ANC3 AN — ADC Channel C3 input.
(1) 2
SCL1 I C OD MSSP1 I2C input/output.
MSSP1 SPI serial data input (default input location, SDI1 is a
SDI1(1) TTL/ST —
PPS remappable input and output).
T2IN(1) TTL/ST — Timer2 external input.

IOCC3 TTL/ST — Interrupt-on-change input.


RC4/ANC4/SDA1(1)/SDI1(1)/IOCC4 RC4 TTL/ST CMOS/OD General purpose I/O.

ANC4 AN — ADC Channel C4 input.


(1) 2
SDA1 I C OD MSSP1 I2C serial data input/output.
MSSP1 SPI serial data input (default input location, SDI1 is a
SDI1(1) TTL/ST —
PPS remappable input and output).
IOCC4 TTL/ST — Interrupt-on-change input.
RC5/ANC5/IOCC5 RC5 TTL/ST CMOS/OD General purpose I/O.

ANC5 AN — ADC Channel C5 input.

IOCC5 TTL/ST — Interrupt-on-change input.


(1)
RC6/ANC6/TX1/CK1 /IOCC6 RC6 TTL/ST CMOS/OD General purpose I/O.

ANC6 AN — ADC Channel C6 input.

TX1 — CMOS EUSART1 asynchronous.


(1)
CK1 TTL/ST CMOS/OD EUSART Synchronous mode clock input/output.

IOCC6 TTL/ST — Interrupt-on-change input.


RC7/ANC7/RX1/DT1(1)/IOCC7 RC7 TTL/ST CMOS/OD General purpose I/O.

ANC7 AN — ADC Channel C7 input.

RX1 TTL/ST — EUSART1 Asynchronous mode receiver data input.


(1)
DT1 TTL/ST CMOS/OD EUSART1 Synchronous mode data input/output.

IOCC7 TTL/ST — Interrupt-on-change input.


RD0/AND0/SCL2(1,4)/SCK2(1)/ RD0 TTL/ST CMOS/OD General purpose I/O.

AND0 AN — ADC Channel D0 input.


(1,4) 2
SCL2 I C OD MSSP2 I2C input/output.
MSSP2 SPI clock input/output (default input location, SCK2 is a
SCK2(1) TTL/ST CMOS/OD
PPS remappable input and output).
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 33


PIC16(L)F15356/75/76/85/86
TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RD1/AND1/SDA1(1)/SDI1(1) RD1 TTL/ST CMOS/OD General purpose I/O.

AND1 AN — ADC Channel D0 input.


(1) 2
SDA1 I C OD MSSP1 I2C serial data input/output.

SDI1(1) TTL/ST — MSSP1 SPI serial data input.


RD2/AND2 RD2 TTL/ST CMOS/OD General purpose I/O.

AND2 AN — ADC Channel D0 input.


RD3/AND3 RD3 TTL/ST CMOS/OD General purpose I/O.

AND3 AN — ADC Channel D0 input.


RD4/AND4 RD4 TTL/ST CMOS/OD General purpose I/O.

AND4 AN — ADC Channel D0 input.


RD5/AND5 RD5 TTL/ST CMOS/OD General purpose I/O.

AND5 AN — ADC Channel D0 input.


RD6/AND6 RD6 TTL/ST CMOS/OD General purpose I/O.

AND6 AN — ADC Channel D0 input.


RD7/AND7 RD7 TTL/ST CMOS/OD General purpose I/O.

AND7 AN — ADC Channel D0 input.


RE0/ANE0 RE0 TTL/ST CMOS/OD General purpose I/O.

ANE0 AN — ADC Channel D0 input.


RE1/ANE1 RE1 TTL/ST CMOS/OD General purpose I/O.

ANE1 AN — ADC Channel D0 input.


RE2/ANE2 RE2 TTL/ST CMOS/OD General purpose I/O.

ANE2 AN — ADC Channel D0 input.


RE3/MCLR/IOCE3 General purpose input only (when MCLR is disabled by the
RE3 TTL/ST —
Configuration bit).
MCLR ST — Master clear input with internal weak pull-up resistor.

IOCE3 TTL/ST — Interrupt-on-change input.


VDD VDD Power — Positive supply voltage input.
VSS VSS Power — Ground reference.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 34


PIC16(L)F15356/75/76/85/86
TABLE 1-3: PIC16(L)F15375/76 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

OUT(2) C1OUT — CMOS/OD Comparator 1 output.

C2OUT — CMOS/OD Comparator 2 output.

NCO1OUT — CMOS/OD Numerically Controller Oscillator output.

TMR0 — CMOS/OD Timer0 output.

CCP1 — CMOS/OD Capture/Compare/PWM1 output (compare/PWM functions).

CCP2 — CMOS/OD Capture/Compare/PWM2 output (compare/PWM functions).

PWM3OUT — CMOS/OD PWM3 output.

PWM4OUT — CMOS/OD PWM4 output.

PWM5OUT — CMOS/OD PWM5 output.

CWG1A — CMOS/OD Complementary Waveform Generator 1 output A.

CWG1B — CMOS/OD Complementary Waveform Generator 1 output B.

CWG1C — CMOS/OD Complementary Waveform Generator 1 output C.

CWG1D — CMOS/OD Complementary Waveform Generator 1 output D.

CWG2A — CMOS/OD Complementary Waveform Generator 2 output A.

CWG2B — CMOS/OD Complementary Waveform Generator 2 output B.

CWG2C — CMOS/OD Complementary Waveform Generator 2 output C.

CWG2D — CMOS/OD Complementary Waveform Generator 2 output D.

SDO1 — CMOS/OD MSSP1 SPI serial data output.

SDO2 — CMOS/OD MSSP2 SPI serial data output.

SCL1(3,4) — CMOS/OD MSSP1 SPI serial clock output.

SCL2(3,4) — CMOS/OD MSSP2 SPI serial clock output.


(3,4)
SDA1 — CMOS/OD MSSP1 I2C serial data input/output.

SDA2(3,4) — CMOS/OD MSSP2 I2C serial data input/output.


(3)
DT — CMOS/OD EUSART Synchronous mode data output.

CK1 — CMOS/OD EUSART1 Synchronous mode clock output.

CK2 — CMOS/OD EUSART2 Synchronous mode clock output.

TX1 — CMOS/OD EUSART1 Asynchronous mode transmitter data output.

TX2 — CMOS/OD EUSART2 Asynchronous mode transmitter data output.

CLC1OUT — CMOS/OD Configurable Logic Cell 1 output.

CLC2OUT — CMOS/OD Configurable Logic Cell 2 output.

CLC3OUT — CMOS/OD Configurable Logic Cell 3 output.

CLC4OUT — CMOS/OD Configurable Logic Cell 4 output.

CLKR — CMOS/OD Clock Reference module output.


Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open-Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-6.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 35


PIC16(L)F15356/75/76/85/86

TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION


Name Input
Function Output Type Description
Type

RA0/ANA0/C1IN0-/C2IN0-/CLCIN0(1)/ RA0 TTL/ST CMOS/OD General purpose I/O.


IOCA0
ANA0 AN — ADC Channel A0 input.

C1IN0- AN — Comparator negative input.

C2IN0- AN — Comparator negative input.

CLCIN0(1) TTL/ST — Configurable Logic Cell source input.

IOCA0 TTL/ST — Interrupt-on-change input.


RA1/ANA1/C1IN1-/C2IN1-/CLCIN1(1)/ RA1 TTL/ST CMOS/OD General purpose I/O.
IOCA1
ANA1 AN — ADC Channel A1 input.

C1IN1- AN — Comparator negative input.

C2IN1- AN — Comparator negative input.

CLCIN1(1) TTL/ST — Configurable Logic Cell source input.

IOCA1 TTL/ST — Interrupt-on-change input.


RA2/ANA2/C1IN0+/C2IN0+/ RA2 TTL/ST CMOS/OD General purpose I/O.
DAC1OUT1/IOCA2
ANA2 AN — ADC Channel A2 input.

C1IN0+ AN — Comparator positive input.

C2IN0+ AN — Comparator positive input.

DAC1OUT1 — AN Digital-to-Analog Converter output.

IOCA2 TTL/ST — Interrupt-on-change input.


RA3/ANA3/C1IN1+/VREF+/DACREF+/ RA3 TTL/ST CMOS/OD General purpose I/O.
IOCA3
ANA3 AN — ADC Channel A3 input.

C1IN1+ AN — Comparator positive input.

VREF+ AN — External ADC and/or DAC positive reference input.

IOCA3 TTL/ST — Interrupt-on-change input.


RA4/ANA4/C1IN1-/T0CKI(1)/IOCA4 RA4 TTL/ST CMOS/OD General purpose I/O.

ANA4 AN — ADC Channel A4 input.

C1IN1- AN — Comparator negative input.

T0CKI(1) TTL/ST — Timer0 clock input.

IOCA4 TTL/ST — Interrupt-on-change input.


RA5/ANA5/SS1(1)/T1G(1)/IOCA5 RA5 TTL/ST CMOS/OD General purpose I/O.

ANA5 AN — ADC Channel A5 input.


(1)
SS1 TTL/ST — MSSP1 SPI slave select input.

T1G(1) TTL/ST — Timer1 gate input.

IOCA5 TTL/ST — Interrupt-on-change input.


Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 36


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RA6/ANA6/CLKOUT/IOCA6/OSC1 RA6 TTL/ST CMOS/OD General purpose I/O.

ANA6 AN — ADC Channel A6 input.

CLKOUT — CMOS/OD FOSC/4 digital output (in non-crystal/resonator modes).

IOCA6 TTL/ST — Interrupt-on-change input.

OSC1 XTAL — External Crystal/Resonator (LP, XT, HS modes) driver input.


RA7/ANA7/CLKIN/IOCA7/OSC2 RA7 TTL/ST CMOS/OD General purpose I/O.

ANA7 AN — ADC Channel A7 input.

CLKIN TTL/ST — External digital clock input.

IOCA7 TTL/ST — Interrupt-on-change input.

OSC2 — XTAL External Crystal/Resonator (LP, XT, HS modes) driver output.


RB0/ANB0/C2IN1+/ZCD1/SS2(1)/ RB0 TTL/ST CMOS/OD General purpose I/O.
CWG1(1)/INT(1)/IOCB0
ANB0 AN — ADC Channel B0 input.

C2IN1+ AN — Comparator positive input.

ZCD1 AN AN Zero-cross detect input pin (with constant current sink/source).

SS2(1) TTL/ST — MSSP2 SPI slave select input.


(1)
CWG1 TTL/ST — Complementary Waveform Generator 1 input.

INT(1) TTL/ST — External interrupt request input.

IOCB0 TTL/ST — Interrupt-on-change input.


RB1/ANB1/C1IN3-/C2IN3-/ RB1 TTL/ST CMOS/OD General purpose I/O.
SCL1(1)/SCK1(1)/IOCB1
ANB1 AN — ADC Channel B1 input.

C1IN3- AN — Comparator negative input.

C2IN3- AN — Comparator negative input.

SCL1(1) I2C OD MSSP1 I2C input/output.


MSSP1 SPI clock input/output (default input location, SCK1 is a
SCK1(1) TTL/ST CMOS/OD
PPS remappable input and output).
IOCB1 TTL/ST — Interrupt-on-change input.
RB2/ANB2/SDA1(1)/SDI1(1,4)/IOCB2 RB2 TTL/ST CMOS/OD General purpose I/O.

ANB2 AN — ADC Channel B2 input.

SDA1(1) I2C OD MSSP1 I2C serial data input/output.

SDI1(1,4) TTL/ST — MSSP1 SPI serial data input.

IOCB2 TTL/ST — Interrupt-on-change input.


RB3/ANB3/C1IN2-/C2IN2-/IOCB3 RB3 TTL/ST CMOS/OD General purpose I/O.

ANB3 AN — ADC Channel B3 input.

C1IN2- AN — Comparator negative input.

C2IN2- AN — Comparator negative input.

IOCB3 TTL/ST — Interrupt-on-change input.


Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 37


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RB4/ANB4/ADACT(1)/IOCB4 RB4 TTL/ST CMOS/OD General purpose I/O.

ANB4 AN — ADC Channel B4 input.


(1)
ADACT TTL/ST — ADC Auto-Conversion Trigger input.

IOCB4 TTL/ST — Interrupt-on-change input.


RB5/ANB5/IOCB5 RB5 TTL/ST CMOS/OD General purpose I/O.

ANB5 AN — ADC Channel B5 input.

IOCB5 TTL/ST — Interrupt-on-change input.


RB6/ANB6/CLCIN2(1)/TX2/CK2(1)/ RB6 TTL/ST CMOS/OD General purpose I/O.
IOCB6/ICSPCLK
ANB6 AN — ADC Channel B6 input.

CLCIN2(1) TTL/ST — Configurable Logic Cell source input.

TX2 TTL/ST — EUSART2 Asynchronous mode receiver data input.


(1)
CK2 TTL/ST CMOS/OD EUSART2 Synchronous mode clock input/output.

IOCB6 TTL/ST — Interrupt-on-change input.

ICSPCLK ST — In-Circuit Serial Programming™ and debugging clock input.


RB7/ANB7/DAC1OUT2/CLCIN3(1)/ RB7 TTL/ST CMOS/OD General purpose I/O.
RX2/DT2(1)/IOCB7/ICSPDAT
ANB7 AN — ADC Channel B7 input.

DAC1OUT2 — AN Digital-to-Analog Converter output.

CLCIN3(1) TTL/ST — Configurable Logic Cell source input.

RX2 TTL/ST — EUSART2 Asynchronous mode receiver data input.

DT2 TTL/ST CMOS/OD EUSART2 Synchronous mode data input/output.

IOCB7 TTL/ST — Interrupt-on-change input.


In-Circuit Serial Programming™ and debugging data input/out-
ICSPDAT ST CMOS
put.
RC0/ANC0/T1CKI(1)/IOCC0/SOSCO RC0 TTL/ST CMOS/OD General purpose I/O.

ANC0 AN — ADC Channel C0 input.

T1CKI(1) TTL/ST — Timer1 external digital clock input.

IOCC0 TTL/ST — Interrupt-on-change input.

SOSCO — AN 32.768 kHz secondary oscillator crystal driver output.


RC1/ANC1/CCP2(1)/IOCC1/SOSCI RC1 TTL/ST CMOS/OD General purpose I/O.

ANC1 AN — ADC Channel C1 input.

(1) Capture/compare/PWM2 (default input location for capture


CCP2 TTL/ST CMOS/OD
function).
IOCC1 TTL/ST — Interrupt-on-change input.

SOSCI AN — 32.768 kHz secondary oscillator crystal driver input.


Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 38


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RC2/ANC2/CCP1(1)/IOCC2 RC2 TTL/ST CMOS/OD General purpose I/O.

ANC2 AN — ADC Channel C2 input.


Capture/compare/PWM1 (default input location for capture
CCP1(1) TTL/ST CMOS/OD
function).
IOCC2 TTL/ST — Interrupt-on-change input.
RC3/ANC3/SCL1(1)/SDI1(1,4)/T2IN(1)/ RC3 TTL/ST CMOS/OD General purpose I/O.
IOCC3
ANC3 AN — ADC Channel C3 input.
(1) 2
SCL1 I C OD MSSP1 I2C input/output.
MSSP1 SPI serial data input (default input location, SDI1 is a
SDI1(1,4) TTL/ST —
PPS remappable input and output).
T2IN(1) TTL/ST — Timer2 external input.

IOCC3 TTL/ST — Interrupt-on-change input.


RC4/ANC4/SDA1(1)/SDI1(1,4)/IOCC4 RC4 TTL/ST CMOS/OD General purpose I/O.

ANC4 AN — ADC Channel C4 input.


(1) 2
SDA1 I C OD MSSP1 I2C serial data input/output.
MSSP1 SPI serial data input (default input location, SDI1 is a
SDI1(1,4) TTL/ST —
PPS remappable input and output).
IOCC4 TTL/ST — Interrupt-on-change input.
RC5/ANC5/IOCC5 RC5 TTL/ST CMOS/OD General purpose I/O.

ANC5 AN — ADC Channel C5 input.

IOCC5 TTL/ST — Interrupt-on-change input.


(3)
RC6/ANC6/TX1/CK1 /IOCC6 RC6 TTL/ST CMOS/OD General purpose I/O.

ANC6 AN — ADC Channel C6 input.

TX1 — CMOS EUSART1 asynchronous.


(3)
CK1 TTL/ST CMOS/OD EUSART Synchronous mode clock input/output.

IOCC6 TTL/ST — Interrupt-on-change input.


RC7/ANC7/RX1/DT1(1)/IOCC7 RC7 TTL/ST CMOS/OD General purpose I/O.

ANC7 AN — ADC Channel C7 input.

RX1 TTL/ST — EUSART1 Asynchronous mode receiver data input.


(1)
DT1 TTL/ST CMOS/OD EUSART1 Synchronous mode data input/output.

IOCC7 TTL/ST — Interrupt-on-change input.


RD0/AND0/SCK2(1)/SCL2(1,4) RD0 TTL/ST CMOS/OD General purpose I/O.

AND0 AN — ADC Channel D0 input.


(1)
SCK2 TTL/ST CMOS/OD MSSP2 SPI clock input/output.
MSSP2 I2C input/output (default input location, SCL2 is a PPS
SCL2(1,4) I2C OD
remappable input and output).
Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 39


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RD1/AND1/SDA2(1)/SDI2(1,4) RD1 TTL/ST CMOS/OD General purpose I/O.

AND1 AN — ADC Channel D0 input.


(1) 2
SDA2 I C OD MSSP2 I2C serial data input/output.
MSSP2 SPI serial data input (default input location, SDI2 is a
SDI2(1,4) TTL/ST —
PPS remappable input and output).
RD2/AND2 RD2 TTL/ST CMOS/OD General purpose I/O.

AND2 AN — ADC Channel D0 input.


RD3/AND3 RD3 TTL/ST CMOS/OD General purpose I/O.

AND3 AN — ADC Channel D0 input.


RD4/AND4 RD4 TTL/ST CMOS/OD General purpose I/O.

AND4 AN — ADC Channel D0 input.


RD5/AND5 RD5 TTL/ST CMOS/OD General purpose I/O.

AND5 AN — ADC Channel D0 input.


RD6/AND6 RD6 TTL/ST CMOS/OD General purpose I/O.

AND6 AN — ADC Channel D0 input.


RD7/AND7 RD7 TTL/ST CMOS/OD General purpose I/O.

AND7 AN — ADC Channel D0 input.


RE0/ANE0 RE0 TTL/ST CMOS/OD General purpose I/O.

ANE0 AN — ADC Channel D0 input.


RE1/ANE1 RE1 TTL/ST CMOS/OD General purpose I/O.

ANE1 AN — ADC Channel D0 input.


RE2/ANE2 RE2 TTL/ST CMOS/OD General purpose I/O.

ANE2 AN — ADC Channel D0 input.


RE3/MCLR/IOCE3 General purpose input only (when MCLR is disabled by the
RE3 TTL/ST —
Configuration bit).
MCLR ST — Master clear input with internal weak pull-up resistor.

IOCE3 TTL/ST — Interrupt-on-change input.


RF0/ANF0 RF0 TTL/ST CMOS/OD General purpose I/O.

ANF0 AN — ADC Channel D0 input.


RF1/ANF1 RF1 TTL/ST CMOS/OD General purpose I/O.

ANF1 AN — ADC Channel D0 input.


RF2/ANF2 RF2 TTL/ST CMOS/OD General purpose I/O.

ANF2 AN — ADC Channel D0 input.


RF3/ANF3 RF3 TTL/ST CMOS/OD General purpose I/O.

ANF3 AN — ADC Channel D0 input.


RF4/ANF4 RF4 TTL/ST CMOS/OD General purpose I/O.

ANF4 AN — ADC Channel D0 input.


Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 40


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

RF5/ANF5 RF5 TTL/ST CMOS/OD General purpose I/O.

ANF5 AN — ADC Channel D0 input.


RF6/ANF6 RF6 TTL/ST CMOS/OD General purpose I/O.

ANF6 AN — ADC Channel D0 input.


RF7/ANF7 RF5 TTL/ST CMOS/OD General purpose I/O.

ANF5 AN — ADC Channel D0 input.


VDD VDD Power — Positive supply voltage input.
VSS VSS Power — Ground reference.
Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 41


PIC16(L)F15356/75/76/85/86
TABLE 1-4: PIC16(L)F15385/86 PINOUT DESCRIPTION (CONTINUED)
Name Input
Function Output Type Description
Type

OUT(2) C1OUT — CMOS/OD Comparator 1 output.

C2OUT — CMOS/OD Comparator 2 output.

NCO1OUT — CMOS/OD Numerically Controller Oscillator output.

TMR0 — CMOS/OD Timer0 output.

CCP1 — CMOS/OD Capture/Compare/PWM1 output (compare/PWM functions).

CCP2 — CMOS/OD Capture/Compare/PWM2 output (compare/PWM functions).

PWM3OUT — CMOS/OD PWM3 output.

PWM4OUT — CMOS/OD PWM4 output.

PWM5OUT — CMOS/OD PWM5 output.

CWG1A — CMOS/OD Complementary Waveform Generator 1 output A.

CWG1B — CMOS/OD Complementary Waveform Generator 1 output B.

CWG1C — CMOS/OD Complementary Waveform Generator 1 output C.

CWG1D — CMOS/OD Complementary Waveform Generator 1 output D.

CWG2A — CMOS/OD Complementary Waveform Generator 2 output A.

CWG2B — CMOS/OD Complementary Waveform Generator 2 output B.

CWG2C — CMOS/OD Complementary Waveform Generator 2 output C.

CWG2D — CMOS/OD Complementary Waveform Generator 2 output D.

SDO1 — CMOS/OD MSSP1 SPI serial data output.

SDO2 — CMOS/OD MSSP2 SPI serial data output.

SCK1 — CMOS/OD MSSP1 SPI serial clock output.

SCK2 — CMOS/OD MSSP2 SPI serial clock output.


(3)
SCK1 — CMOS/OD MSSP1 SPI serial clock output.

SCK2(3) — CMOS/OD MSSP2 SPI serial clock output.


(3,4)
SDA1 — CMOS/OD MSSP1 I2C serial data input/output.

SDA2(3,4) — CMOS/OD MSSP2 I2C serial data input/output.

DT(3) — CMOS/OD EUSART Synchronous mode data output.

CK1 — CMOS/OD EUSART1 Synchronous mode clock output.

CK2 — CMOS/OD EUSART2 Synchronous mode clock output.

TX1 — CMOS/OD EUSART1 Asynchronous mode transmitter data output.

TX2 — CMOS/OD EUSART2 Asynchronous mode transmitter data output.

CLC1OUT — CMOS/OD Configurable Logic Cell 1 output.

CLC2OUT — CMOS/OD Configurable Logic Cell 2 output.

CLC3OUT — CMOS/OD Configurable Logic Cell 3 output.

CLC4OUT — CMOS/OD Configurable Logic Cell 4 output.

CLKR — CMOS/OD Clock Reference module output.


Legend: AN= Analog input or output CMOS=CMOS compatible input or output OD=Open-Drain
TTL= TTL compatible input ST= Schmitt Trigger input with CMOS levels I2C=Schmitt Trigger input with I2C
HV= High Voltage XTAL= Crystal levels
Note 1: This is a PPS remappable input signal. The input function may be moved from the default location shown to one of several other PORTx
pins. Refer to Table 15-6 for details on which PORT pins may be used for this signal.
2: All output signals shown in this row are PPS remappable. These signals may be mapped to output onto one of several PORTx pin options
as described in Table 15-5, Table 15-6 and Table 15-7.
3: This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and
PPS output registers.
4: These pins are configured for I2C logic levels. The SCLx/SDAx signals may be assigned to any of the RB1/RB2/RC3/RC4 pins. PPS
assignments to the other pins (e.g., RA5) will operate, but input logic levels will be standard TTL/ST, as selected by the INLVL register,
instead of the I2C specific or SMBus input buffer thresholds.

 2016-2018 Microchip Technology Inc. DS40001866B-page 42


PIC16(L)F15356/75/76/85/86
2.0 GUIDELINES FOR GETTING 2.2 Power Supply Pins
STARTED WITH
2.2.1 DECOUPLING CAPACITORS
PIC16(L)F15356/75/76/85/86
The use of decoupling capacitors on every pair of
MICROCONTROLLERS power supply pins (VDD and VSS) is required.
Consider the following criteria when using decoupling
2.1 Basic Connection Requirements
capacitors:
Getting started with the PIC16(L)F15356/75/76/85/86 • Value and type of capacitor: A 0.1 F (100 nF),
family of 8-bit microcontrollers requires attention to a 10-25V capacitor is recommended. The capacitor
minimal set of device pin connections before should be a low-ESR device, with a resonance
proceeding with development. frequency in the range of 200 MHz and higher.
The following pins must always be connected: Ceramic capacitors are recommended.
• All VDD and VSS pins • Placement on the printed circuit board: The
(see Section 2.2 “Power Supply Pins”) decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
• MCLR pin
place the capacitors on the same side of the
(see Section 2.3 “Master Clear (MCLR) Pin”)
board as the device. If space is constricted, the
These pins must also be connected if they are being capacitor can be placed on another layer on the
used in the end application: PCB using a via; however, ensure that the trace
• ICSPCLK/ICSPDAT pins used for In-Circuit Serial length from the pin to the capacitor is no greater
Programming™ (ICSP™) and debugging purposes than 0.25 inch (6 mm).
(see Section 2.4 “ICSP™ Pins”) • Handling high-frequency noise: If the board is
• OSCI and OSCO pins when an external oscillator experiencing high-frequency noise (upward of
source is used tens of MHz), add a second ceramic type capaci-
(see Section 2.5 “External Oscillator Pins”) tor in parallel to the above described decoupling
capacitor. The value of the second capacitor can
Additionally, the following pins may be required:
be in the range of 0.01 F to 0.001 F. Place this
• VREF+/VREF- pins are used when external voltage second capacitor next to each primary decoupling
reference for analog modules is implemented capacitor. In high-speed circuit designs, consider
The minimum mandatory connections are shown in implementing a decade pair of capacitances as
Figure 2-1. close to the power and ground pins as possible
(e.g., 0.1 F in parallel with 0.001 F).
FIGURE 2-1: RECOMMENDED • Maximizing performance: On the board layout
MINIMUM CONNECTIONS from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
C2 decoupling capacitors are first in the power chain.
VDD Equally important is to keep the trace length
between the capacitor and the power pins to a
VDD

VSS

R1 minimum, thereby reducing PCB trace


R2 inductance.
MCLR
2.2.2 TANK CAPACITORS
C1
PIC16(L)F153xx On boards with power traces running longer than
six inches in length, it is suggested to use a tank capac-
VSS itor for integrated circuits, including microcontrollers, to
supply a local power source. The value of the tank
capacitor should be determined based on the trace
resistance that connects the power supply source to
the device, and the maximum current drawn by the
Key (all values are recommendations): device in the application. In other words, select the tank
C1: 10nF, 16V ceramic capacitor so that it meets the acceptable voltage sag at
C2: 0.1uF, 16V ceramic the device. Typical values range from 4.7 F to 47 F.
R1: 10 kΩ
R2: 100Ω to 470Ω

 2016-2018 Microchip Technology Inc. DS40001866B-page 43


PIC16(L)F15356/75/76/85/86
2.3 Master Clear (MCLR) Pin 2.4 ICSP™ Pins
The MCLR pin provides two specific device The ICSPCLK and ICSPDAT pins are used for In-Cir-
functions: Device Reset, and Device Programming cuit Serial Programming™ (ICSP™) and debugging
and Debugging. If programming and debugging are purposes. It is recommended to keep the trace length
not required in the end application, a direct between the ICSP connector and the ICSP pins on the
connection to VDD may be all that is required. The device as short as possible. If the ICSP connector is
addition of other components, to help increase the expected to experience an ESD event, a series resistor
application’s resistance to spurious Resets from is recommended, with the value in the range of a few
voltage sags, may be beneficial. A typical tens of ohms, not to exceed 100Ω.
configuration is shown in Figure 2-1. Other circuit Pull-up resistors, series diodes and capacitors on the
designs may be implemented, depending on the ICSPCLK and ICSPDAT pins are not recommended as
application’s requirements. they will interfere with the programmer/debugger com-
During programming and debugging, the resistance munications to the device. If such discrete components
and capacitance that can be added to the pin must are an application requirement, they should be
be considered. Device programmers and debuggers removed from the circuit during programming and
drive the MCLR pin. Consequently, specific voltage debugging. Alternatively, refer to the AC/DC character-
levels (VIH and VIL) and fast signal transitions must istics and timing requirements information in the
not be adversely affected. Therefore, specific values respective device Flash programming specification for
of R1 and C1 will need to be adjusted based on the information on capacitive loading limits, and pin input
application and PCB requirements. For example, it is voltage high (VIH) and input low (VIL) requirements.
recommended that the capacitor, C1, be isolated For device emulation, ensure that the “Communication
from the MCLR pin during programming and Channel Select” (i.e., ICSPCLK/ICSPDAT pins),
debugging operations by using a jumper (Figure 2-2). programmed into the device, matches the physical
The jumper is replaced for normal run-time connections for the ICSP to the Microchip debugger/
operations. emulator tool.
Any components associated with the MCLR pin For more information on available Microchip
should be placed within 0.25 inch (6 mm) of the pin. development tools connection requirements, refer to
Section 39.0 “Development Support”.
FIGURE 2-2: EXAMPLE OF MCLR PIN
CONNECTIONS
VDD

R1
R2
MCLR

JP PIC16(L)F153xx

C1

Note 1: R1  10 k is recommended. A suggested


starting value is 10 k. Ensure that the
MCLR pin VIH and VIL specifications are met.
2: R2  470 will limit any current flowing into
MCLR from the external capacitor, C1, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.

 2016-2018 Microchip Technology Inc. DS40001866B-page 44


PIC16(L)F15356/75/76/85/86
2.5 External Oscillator Pins 2.6 Unused I/Os
Many microcontrollers have options for at least two Unused I/O pins should be configured as outputs and
oscillators: a high-frequency primary oscillator and a driven to a logic low state. Alternatively, connect a 1 kΩ
low-frequency secondary oscillator (refer to to 10 kΩ resistor to VSS on unused pins and drive the
Section 9.0 “Oscillator Module (with Fail-Safe output to logic low.
Clock Monitor)” for details).
The oscillator circuit should be placed on the same FIGURE 2-3: SUGGESTED
side of the board as the device. Place the oscillator PLACEMENT OF THE
circuit close to the respective oscillator pins with no OSCILLATOR CIRCUIT
more than 0.5 inch (12 mm) between the circuit
Single-Sided and In-Line Layouts:
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side Copper Pour Primary Oscillator
of the board. (tied to ground) Crystal

Use a grounded copper pour around the oscillator cir- DEVICE PINS
cuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
Primary OSC1
traces inside the ground pour. Also, if using a two-sided Oscillator
board, avoid any traces on the other side of the board C1 ` OSC2
where the crystal is placed.
C2 GND
Layout suggestions are shown in Figure 2-3. In-line `
packages may be handled with a single-sided layout
SOSCO
that completely encompasses the oscillator pins. With
fine-pitch packages, it is not always possible to com- SOSCI
Secondary Oscillator
pletely surround the pins and components. A suitable (SOSC)
solution is to tie the broken guard sections to a mirrored Crystal `
ground layer. In all cases, the guard trace(s) must be
returned to ground.
SOSC: C1 SOSC: C2
In planning the application’s routing and I/O assign-
ments, ensure that adjacent port pins, and other
signals in close proximity to the oscillator, are benign
(i.e., free of high frequencies, short rise and fall times, Fine-Pitch (Dual-Sided) Layouts:
and other similar noise). Top Layer Copper Pour
(tied to ground)
For additional information and design guidance on
oscillator circuits, refer to these Microchip Application
Notes, available at the corporate website Bottom Layer
Copper Pour
(www.microchip.com): (tied to ground)
• AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC™ and PICmicro® Devices” OSCO

• AN849, “Basic PICmicro® Oscillator Design”


C2
• AN943, “Practical PICmicro® Oscillator Analysis
Oscillator
and Design” GND Crystal
• AN949, “Making Your Oscillator Work”
C1

OSCI

DEVICE PINS

 2016-2018 Microchip Technology Inc. DS40001866B-page 45


PIC16(L)F15356/75/76/85/86
3.0 ENHANCED MID-RANGE CPU
This family of devices contains an enhanced mid-range
8-bit CPU core. The CPU has 48 instructions. Interrupt
capability includes automatic context saving.
The hardware stack is 16-levels deep and has
Overflow and Underflow Reset capability. Direct,
Indirect, and Relative Addressing modes are available.
Two File Select Registers (FSRs) provide the ability to
read program and data memory.
FIGURE 3-1: CORE DATA PATH DIAGRAM

Rev. 10-000055C
11/30/2016

15 Configuration
15 Data Bus 8
Program Counter

Flash
MUX

Program
Memory
16-Level Stack
RAM
(15-bit)

14
Program 12
Program Memory RAM Addr
Bus
Read (PMR)

Instruction Reg Addr MUX


Indirect
Direct Addr 7 Addr
12
5 12

BSR Reg
15
FSR0 Reg

15
FSR1 Reg
STATUS Reg
8

3 MUX
Power-up
Instruction Timer
Decode and
Control Power-on
Reset ALU
8
Watchdog
CLKIN Timer
Brown-out
CLKOUT Timing Reset W Reg
SOSCI Generation

SOSCO

VDD VSS

Internal
Oscillator
Block

 2016-2018 Microchip Technology Inc. DS40001866B-page 46


PIC16(L)F15356/75/76/85/86
3.1 Automatic Interrupt Context
Saving
During interrupts, certain registers are automatically
saved in shadow registers and restored when returning
from the interrupt. This saves stack space and user
code. See Section 10.5 “Automatic Context Saving”
for more information.

3.2 16-Level Stack with Overflow and


Underflow
These devices have a hardware stack memory 15 bits
wide and 16 words deep. A Stack Overflow or
Underflow will set the appropriate bit (STKOVF or
STKUNF) in the PCON0 register, and if enabled, will
cause a software Reset. See Section 4.5 “Stack” for
more details.

3.3 File Select Registers


There are two 16-bit File Select Registers (FSR). FSRs
can access all file registers and program memory,
which allows one Data Pointer for all memory. When an
FSR points to program memory, there is one additional
instruction cycle in instructions using INDF to allow the
data to be fetched. General purpose memory can also
be addressed linearly, providing the ability to access
contiguous data larger than 80 bytes. See Section 4.6
“Indirect Addressing” for more details.

3.4 Instruction Set


There are 48 instructions for the enhanced mid-range
CPU to support the features of the CPU. See
Section 36.0 “Instruction Set Summary” for more
details.

 2016-2018 Microchip Technology Inc. DS40001866B-page 47


PIC16(L)F15356/75/76/85/86
4.0 MEMORY ORGANIZATION 4.1 Program Memory Organization
These devices contain the following types of memory: The enhanced mid-range core has a 15-bit program
counter capable of addressing 32K x 14 program
• Program Memory
memory space. Table 4-1 shows the memory sizes
- Configuration Words implemented. The Reset vector is at 0000h and the
- Device ID interrupt vector is at 0004h (see Figure 4-1).
- User ID
- Program Flash Memory
- Device Information Area (DIA)
- Device Configuration Information (DCI)
- Revision ID
• Data Memory
- Core Registers
- Special Function Registers
- General Purpose RAM
- Common RAM
The following features are associated with access and
control of program memory and data memory:
• PCL and PCLATH
• Stack
• Indirect Addressing
• NVMREG access

TABLE 4-1: DEVICE SIZES AND ADDRESSES


Device Program Memory Size (Words) Last Program Memory Address
PIC16(L)F15356 16384 3FFFh
PIC16(L)F15375 8192 1FFFh
PIC16(L)F15376 16384 3FFFh
PIC16(L)F15385 8192 1FFFh
PIC16(L)F15386 16384 3FFFh

 2016-2018 Microchip Technology Inc. DS40001866B-page 48


PIC16(L)F15356/75/76/85/86

FIGURE 4-1: PROGRAM MEMORY MAP FIGURE 4-2: PROGRAM MEMORY MAP
AND STACK FOR AND STACK FOR
PIC16(L)F15375/85 PIC16(L)F15356/76/86

Rev. 10-000040H Rev. 10-000040I


8/23/2016 8/23/2016

PC<14:0> PC<14:0>
CALL, CALLW CALL, CALLW
RETURN, RETLW 15 RETURN, RETLW 15
Interrupt, RETFIE Interrupt, RETFIE

Stack Level 0 Stack Level 0


Stack Level 1 Stack Level 1

Stack Level 15 Stack Level 15

Reset Vector 0000h Reset Vector 0000h

Interrupt Vector 0004h Interrupt Vector 0004h


0005h 0005h
On-chip On-chip
Program Program 07FFh
Memory Memory 0800h

0FFFh 0FFFh
1000h 1000h

Page 0 17FFh
1800h

1FFFh 1FFFh
2000h 2000h

3FFFh 3FFFh
4000h 4000h
Unimplemented

Unimplemented

7FFFh 7FFFh

 2016-2018 Microchip Technology Inc. DS40001866B-page 49


PIC16(L)F15356/75/76/85/86
4.1.1 READING PROGRAM MEMORY AS
DATA
There are three methods of accessing constants in
program memory. The first method is to use tables of
RETLW instructions. The second method is to set an
FSR to point to the program memory. The third method
is to use the NVMREG interface to access the program
memory. For an example of NVMREG interface use,
reference Section 13.3, NVMREG Access.

4.1.1.1 RETLW Instruction


The RETLW instruction can be used to provide access
to tables of constants. The recommended way to create
such a table is shown in Example 4-1.

EXAMPLE 4-1: RETLW INSTRUCTION


constants
BRW ;Add Index in W to
;program counter to
;select data
RETLW DATA0 ;Index0 data
RETLW DATA1 ;Index1 data
RETLW DATA2
RETLW DATA3

my_function
;… LOTS OF CODE…
MOVLW DATA_INDEX
call constants
;… THE CONSTANT IS IN W

The BRW instruction makes this type of table very


simple to implement.

4.1.1.2 Indirect Read with FSR


The program memory can be accessed as data by
setting bit 7 of an FSRxH register and reading the
matching INDFx register. The MOVIW instruction will
place the lower eight bits of the addressed word in the
W register. Writes to the program memory cannot be
performed via the INDF registers. Instructions that read
the program memory via the FSR require one extra
instruction cycle to complete. Example 4-2
demonstrates reading the program memory via an
FSR.

 2016-2018 Microchip Technology Inc. DS40001866B-page 50


PIC16(L)F15356/75/76/85/86
The HIGH directive will set bit 7 if a label points to a 4.2 Memory Access Partition (MAP)
location in the program memory. This applies to the
assembly code Example 4-2 shown below. User Flash is partitioned into:
• Application Block
EXAMPLE 4-2: ACCESSING PROGRAM • Boot Block, and
• Storage Area Flash (SAF) Block
MEMORY VIA FSR
constants The user can allocate the memory usage by setting
RETLW DATA0 ;Index0 data the BBEN bit, selecting the size of the partition defined
RETLW DATA1 ;Index1 data by BBSIZE[2:0] bits and enabling the Storage Area
RETLW DATA2 Flash by the SAFEN bit of the Configuration Word (see
RETLW DATA3
Register 5-4). Refer to Table 4-2 for the different user
my_function
;… LOTS OF CODE… Flash memory partitions.
MOVLW LOW constants
MOVWF FSR1L 4.2.1 APPLICATION BLOCK
MOVLW HIGH constants Default settings of the Configuration bits (BBEN = 1
MOVWF FSR1H
MOVIW 0[FSR1] and SAFEN = 1) assign all memory in the user Flash
;THE PROGRAM MEMORY IS IN W area to the Application Block.

4.2.2 BOOT BLOCK


If BBEN = 1, the Boot Block is enabled and a specific
address range is alloted as the Boot Block based on
the value of the BBSIZE bits of Configuration Word
(Register 5-4) and the sizes provided in Table 5-1.

4.2.3 STORAGE AREA FLASH


Storage Area Flash (SAF) is enabled by clearing the
SAFEN bit of the Configuration Word in Register 5-4. If
enabled, the SAF block is placed at the end of memory
and spans 128 words. If the Storage Area Flash (SAF)
is enabled, the SAF area is not available for program
execution. The 128 words of the SAF qualify as High
Endurance Flash (HEF) memory.

4.2.4 MEMORY WRITE PROTECTION


All the memory blocks have corresponding write
protection fuses WRTAPP, WRTB and WRTC bits in
the Configuration Word 4 (Register 5-4). If write-
protected locations are written from NVMCON
registers, memory is not changed and the WRERR bit
defined in Register 12-5 is set as explained in
Section 13.3.8 “WRERR Bit”.

4.2.5 MEMORY VIOLATION


A Memory Execution Violation Reset occurs while
executing an instruction that has been fetched from
outside a valid execution area, clearing the MEMV bit.
Refer to Section 8.12 “Memory Execution Violation”
for the available valid program execution areas and the
PCON1 register definition (Register 8-3) for MEMV bit
conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 51


PIC16(L)F15356/75/76/85/86

TABLE 4-2: MEMORY ACCESS PARTITION


Partition
REG Address BBEN = 1 BBEN = 1 BBEN = 0 BBEN = 0
SAFEN = 1 SAFEN = 0 SAFEN = 1 SAFEN = 0
00 0000h
•••
BOOT BLOCK(4) BOOT BLOCK(4)
Last Boot Block Memory
Address
APPLICATION
Last Boot Block Memory BLOCK(4)
Address + 1(1)
APPLICATION
••• APPLICATION
PFM BLOCK(4)
Last Program Memory BLOCK(4)
Address - 80h APPLICATION
Last Program Memory BLOCK(4)
Address - 7Fh(2)
••• SAF(4) SAF(4)
Last Program Memory
Address
CONFIG Config Memory Address(3) CONFIG
Note 1: Last Boot Block Memory Address is based on BBSIZE<2:0> given in Table 5-1.
2: Last Program Memory Address is the Flash size given in Table 4-1.
3: Config Memory Address are the address locations of the Configuration Words given in Table 13-2.
4: Each memory block has a corresponding write protection fuse defined by the WRTAPP, WRTB and WRTC
bits in the Configuration Word (Register 5-4).

 2016-2018 Microchip Technology Inc. DS40001866B-page 52


PIC16(L)F15356/75/76/85/86
4.3 Data Memory Organization 4.3.1 BANK SELECTION
The data memory is partitioned into 64 memory banks The active bank is selected by writing the bank number
with 128 bytes in each bank. Each bank consists of: into the Bank Select Register (BSR). All data memory
can be accessed either directly (via instructions that
• 12 core registers use the file registers) or indirectly via the two File Select
• Up to 100 Special Function Registers (SFR) Registers (FSR). See Section 4.6 “Indirect
• Up to 80 bytes of General Purpose RAM (GPR) Addressing” for more information.
• 16 bytes of common RAM Data memory uses a 13-bit address. The upper six bits
of the address define the Bank address and the lower
FIGURE 4-3: BANKED MEMORY seven bits select the registers/RAM in that bank.
PARTITIONING
Rev. 10-000041B
4.3.2 CORE REGISTERS
9/21/2016

The core registers contain the registers that directly


affect the basic operation. The core registers occupy
7-bit Bank Offset Memory Region the first 12 addresses of every data memory bank
00h
(addresses x00h/x08h through x0Bh/x8Bh). These
Core Registers
registers are listed below in Table 4-3.
(12 bytes)
0Bh TABLE 4-3: CORE REGISTERS
0Ch
Special Function Registers(1)
Addresses BANKx
(up to 100 bytes maximum)
1Fh x00h or x80h INDF0
20h x01h or x81h INDF1
x02h or x82h PCL
x03h or x83h STATUS
x04h or x84h FSR0L
x05h or x85h FSR0H
x06h or x86h FSR1L
x07h or x87h FSR1H
General Purpose RAM
(80 bytes maximum) x08h or x88h BSR
x09h or x89h WREG
x0Ah or x8Ah PCLATH
x0Bh or x8Bh INTCON

6Fh
70h
Common RAM
(16 bytes)
7Fh

Note 1: This table shows the address for an example


bank with 20 Bytes of SFRs only.

 2016-2018 Microchip Technology Inc. DS40001866B-page 53


PIC16(L)F15356/75/76/85/86
4.3.2.1 STATUS Register For example, CLRF STATUS will clear bits <4:3> and
<1:0>, and set the Z bit. This leaves the STATUS
The STATUS register, shown in Register 4-1, contains:
register as ‘000u u1uu’ (where u = unchanged).
• the arithmetic status of the ALU
It is recommended, therefore, that only BCF, BSF,
• the Reset status SWAPF and MOVWF instructions are used to alter the
The STATUS register can be the destination for any STATUS register, because these instructions do not
instruction, like any other register. If the STATUS affect any Status bits. For other instructions not
register is the destination for an instruction that affects affecting any Status bits, refer to Section 36.0
the Z, DC or C bits, then the write to these three bits is “Instruction Set Summary”.
disabled. These bits are set or cleared according to the
Note 1: The C and DC bits operate as Borrow
device logic. Furthermore, the TO and PD bits are not
and Digit Borrow out bits, respectively, in
writable. Therefore, the result of an instruction with the
subtraction.
STATUS register as destination may be different than
intended.
REGISTER 4-1: STATUS: STATUS REGISTER
U-0 U-0 U-0 R-1/q R-1/q R/W-0/u R/W-0/u R/W-0/u
— — — TO PD Z DC(1) C(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-5 Unimplemented: Read as ‘0’


bit 4 TO: Time-Out bit
1 = After power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
bit 3 PD: Power-Down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
bit 2 Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1 DC: Digit Carry/Digit Borrow bit (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1)
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
bit 0 C: Carry/Borrow bit(1) (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred

Note 1: For Borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the
second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order
bit of the source register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 54


PIC16(L)F15356/75/76/85/86
4.3.3 SPECIAL FUNCTION REGISTER
The Special Function Registers are registers used by
the application to control the desired operation of
peripheral functions in the device. The Special Function
Registers occupy the 20 bytes of the data banks 0-59
and 100 bytes of the data banks 60-63, after the core
registers.
The SFRs associated with the operation of the
peripherals are described in the appropriate peripheral
chapter of this data sheet.

4.3.4 GENERAL PURPOSE RAM


There are up to 80 bytes of GPR in each data memory
bank.

4.3.4.1 Linear Access to GPR


The general purpose RAM can be accessed in a non-
banked method via the FSRs. This can simplify access
to large memory structures. See Section 4.6.2 “Linear
Data Memory” for more information.

4.3.5 COMMON RAM


There are 16 bytes of common RAM accessible from all
banks.

4.3.6 DEVICE MEMORY MAPS


The memory maps are as shown in Table 4-4 through
Table 4-11.

 2016-2018 Microchip Technology Inc. DS40001866B-page 55


TABLE 4-4: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 0-7
 2016-2018 Microchip Technology Inc.

BANK 0 BANK 1 BANK 2 BANK 3 BANK 4 BANK 5 BANK 6 BANK 7


000h 080h 100h 180h 200h 280h 300h 380h
Core Register Core Register Core Register Core Register Core Register Core Register Core Register Core Register
(Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3)
00Bh 08Bh 10Bh 18Bh 20Bh 28Bh 30Bh 38Bh
00Ch PORTA 08Ch — 10Ch — 18Ch SSP1BUF 20Ch TMR1L 28Ch TMR2 30Ch CCPR1L 38Ch PWM6DCL
00Dh PORTB 08Dh — 10Dh — 18Dh SSP1ADD 20Dh TMR1H 28Dh PR2 30Dh CCPR1H 38Dh PWM6DCH
00Eh PORTC 08Eh — 10Eh — 18Eh SSP1MASK 20Eh T1CON 28Eh T2CON 30Eh CCP1CON 38Eh PWM6CON
00Fh PORTD(2) 08Fh — 10Fh — 18Fh SSP1STAT 20Fh T1GCON 28Fh T2HLT 30Fh CCP1CAP 38Fh —
010h PORTE 090h — 110h — 190h SSP1CON1 210h T1GATE 290h T2CLK 310h CCPR2L 390h —
011h PORTF(3) 091h — 111h — 191h SSP1CON2 211h T1CLK 291h T2ERS 311h CCPR2H 391h —
012h TRISA 092h — 112h — 192h SSP1CON3 212h — 292h — 312h CCP2CON 392h —
013h TRISB 093h — 113h — 193h — 213h — 293h — 313h CCP2CAP 393h —
014h TRISC 094h — 114h — 194h — 214h — 294h — 314h PWM3DCL 394h —
015h TRISD(2) 095h — 115h — 195h — 215h — 295h — 315h PWM3DCH 395h —
016h TRISE 096h — 116h — 196h SSP2BUF 216h — 296h — 316h PWM3CON 396h —
017h TRISF(3) 097h — 117h — 197h SSP2ADD 217h — 297h — 317h — 397h —
018h LATA 098h — 118h — 198h SSP2MASK 218h — 298h — 318h PWM4DCL 398h —
019h LATB 099h — 119h RC1REG1 199h SSP2STAT 219h — 299h — 319h PWM4DCH 399h —

PIC16(L)F15356/75/76/85/86
01Ah LATC 09Ah — 11Ah TX1REG1 19Ah SSP2CON1 21Ah — 29Ah — 31Ah PWM4CON 39Ah —
01Bh LATD(2) 09Bh ADRESL 11Bh SP1BRG1L 19Bh SSP2CON2 21Bh — 29Bh — 31Bh — 39Bh —
01Ch LATE 09Ch ADRESH 11Ch SP1BRG1H 19Ch SSP2CON3 21Ch — 29Ch — 31Ch PWM5DCL 39Ch —
01Dh LATF(3) 09Dh ADCON0 11Dh RC1STA1 19Dh — 21Dh — 29Dh — 31Dh PWM5DCH 39Dh —
01Eh — 09Eh ADCON1 11Eh TX1STA1 19Eh — 21Eh — 29Eh — 31Eh PWM5CON 39Eh —
01Fh — 09Fh ADACT 11Fh BAUD1CON1 19Fh — 21Fh — 29Fh — 31Fh — 39Fh —
020h 0A0h 120h 1A0h 220h 2A0h 320h 3A0h

General General General General General General General


Purpose Purpose Purpose Purpose Purpose Purpose Purpose
General Register Register Register Register Register Register Register
Purpose 80 Bytes 80 Bytes 80 Bytes 80 Bytes 80 Bytes 80 Bytes 80 Bytes
Register
96 Bytes
0EFh 16Fh 1EFh 26Fh 2EFh 36Fh 3EFh
0F0h Common RAM 170h Common RAM 1F0h Common RAM 270h Common RAM 2F0h Common RAM 370h Common RAM 3F0h Common RAM
Accesses Accesses Accesses Accesses Accesses Accesses Accesses
07Fh 0FFh 70h-7Fh 17Fh 70h-7Fh 1FFh 70h-7Fh 27Fh 70h-7Fh 2FFh 70h-7Fh 37Fh 70h-7Fh 3FFh 70h-7Fh

Note 1: Unimplemented locations read as ‘0’.


2: Present only in PIC16(L)F15375/76/85/86.
DS40001866B-page 56

3: Present only in PIC16(L)F15385/86.


TABLE 4-5: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 8-15
 2016-2018 Microchip Technology Inc.

BANK 8 BANK 9 BANK 10 BANK 11 BANK 12 BANK 13 BANK 14 BANK 15


400h 480h 500h 580h 600h 680h 700h 780h
Core Register Core Register Core Register Core Register Core Register Core Register Core Register Core Register
(Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3)
40Bh 48Bh 50Bh 58Bh 60Bh 68Bh 70Bh 78Bh
40Ch — 48Ch — 50Ch — 58Ch NCO1ACCL 60Ch CWG1CLK 68Ch — 70Ch PIR0 78Ch —
40Dh — 48Dh — 50Dh — 58Dh NCO1ACCH 60Dh CWG1DAT 68Dh — 70Dh PIR1 78Dh —
40Eh — 48Eh — 50Eh — 58Eh NCO1ACCU 60Eh CWG1DBR 68Eh — 70Eh PIR2 78Eh —
40Fh — 48Fh — 50Fh — 58Fh NCO1INCL 60Fh CWG1DBF 68Fh — 70Fh PIR3 78Fh —
410h — 490h — 510h — 590h NCO1INCH 610h CWG1CON0 690h — 710h PIR4 790h —
411h — 491h — 511h — 591h NCO1INCU 611h CWG1CON1 691h — 711h PIR5 791h —
412h — 492h — 512h — 592h NCO1CON 612h CWG1AS0 692h — 712h PIR6 792h —
413h — 493h — 513h — 593h NCO1CLK 613h CWG1AS1 693h — 713h PIR7 793h —
414h — 494h — 514h — 594h — 614h CWG1STR 694h — 714h — 794h —
415h — 495h — 515h — 595h — 615h — 695h — 715h — 795h —
416h — 496h — 516h — 596h — 616h — 696h — 716h PIE0 796h PMD0
417h — 497h — 517h — 597h — 617h — 697h — 717h PIE1 797h PMD1
418h — 498h — 518h — 598h — 618h — 698h — 718h PIE2 798h PMD2

PIC16(L)F15356/75/76/85/86
419h — 499h — 519h — 599h — 619h — 699h — 719h PIE3 799h PMD3
41Ah — 49Ah — 51Ah — 59Ah — 61Ah — 69Ah — 71Ah PIE4 79Ah PMD4
41Bh — 49Bh — 51Bh — 59Bh — 61Bh — 69Bh — 71Bh PIE5 79Bh PMD5
41Ch — 49Ch — 51Ch — 59Ch TMR0 61Ch — 69Ch — 71Ch PIE6 79Ch —
41Dh — 49Dh — 51Dh — 59Dh PR0 61Dh — 69Dh — 71Dh PIE7 79Dh —
41Eh — 49Eh — 51Eh — 59Eh TMR0CON0 61Eh — 69Eh — 71Eh — 79Eh —
41Fh — 49Fh — 51Fh — 59Fh TMR0CON1 61Fh — 69Fh — 71Fh — 79Fh —
420h 4A0h 520h 5A0h 620h General 6A0h 720h 7A0h
Purpose General
General General General General Register General General
Purpose Purpose Purpose Purpose 64Fh 48 Bytes Purpose Purpose Purpose
Register Register Register Register General Register Register
650h Register
80 Bytes 80 Bytes 80 Bytes 80 Bytes Purpose 80 Bytes(2) 80 Bytes(2)
Register 80 Bytes(2)

46Fh 4EFh 56Fh 5EFh 66Fh 32 Bytes(2) 6EFh 76Fh 7EFh


470h Common RAM 4F0h Common RAM 570h Common RAM 5F0h Common RAM 670h Common RAM 6F0h Common RAM 770h Common RAM 7F0h Common RAM
Accesses Accesses Accesses Accesses Accesses Accesses Accesses Accesses
47Fh 70h-7Fh 4FFh 70h-7Fh 57Fh 70h-7Fh 5FFh 70h-7Fh 67Fh 70h-7Fh 6FFh 70h-7Fh 77Fh 70h-7Fh 7FFh 70h-7Fh

Note 1: Unimplemented locations read as ‘0’.


2: Present only on PIC16(L)F15356/76/86.
DS40001866B-page 57
TABLE 4-6: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 16-23
 2016-2018 Microchip Technology Inc.

BANK 16 BANK 17 BANK 18 BANK 19 BANK 20 BANK 21 BANK 22 BANK 23


800h 880h 900h 980h A00h A80h B00h B80h
Core Register Core Register Core Register Core Register Core Register Core Register Core Register Core Register
(Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3)
80Bh 88Bh 90Bh 98Bh A0Bh A8Bh B0Bh B8Bh
80Ch WDTCON0 88Ch CPUDOZE 90Ch FVRCON 98Ch — A0Ch — A8Ch — B0Ch — B8Ch —
80Dh WDTCON1 88Dh OSCCON1 90Dh — 98Dh — A0Dh — A8Dh — B0Dh — B8Dh —
80Eh WDTL 88Eh OSCCON2 90Eh DAC1CON0 98Eh — A0Eh — A8Eh — B0Eh — B8Eh —
80Fh WDTH 88Fh OSCCON3 90Fh DAC1CON1 98Fh CMOUT A0Fh — A8Fh — B0Fh — B8Fh —
810h WDTU 890h OSCSTAT1 910h — 990h CM1CON0 A10h — A90h — B10h — B90h —
811h BORCON 891h OSCEN 911h — 991h CM1CON1 A11h — A91h — B11h — B91h —
812h VREGCON(2) 892h OSCTUNE 912h — 992h CM1NCH A12h — A92h — B12h — B92h —
813h PCON0 893h OSCFRQ 913h — 993h CM1PCH A13h — A93h — B13h — B93h —
814h PCON1 894h — 914h — 994h CM2CON0 A14h — A94h — B14h — B94h —
815h — 895h CLKRCON 915h — 995h CM2CON1 A15h — A95h — B15h — B95h —
816h — 896h CLKCLK 916h — 996h CM2NCH A16h — A96h — B16h — B96h —
817h — 897h — 917h — 997h CM2PCH A17h — A97h — B17h — B97h —
818h — 898h — 918h — 998h — A18h — A98h — B18h — B98h —

PIC16(L)F15356/75/76/85/86
819h — 899h — 919h — 999h — A19h RC2REG A99h — B19h — B99h —
81Ah NVMADRL 89Ah — 91Ah — 99Ah — A1Ah TX2REG A9Ah — B1Ah — B9Ah —
81Bh NVMADRH 89Bh — 91Bh — 99Bh — A1Bh SP2BRGL A9Bh — B1Bh — B9Bh —
81Ch NVMDATL 89Ch — 91Ch — 99Ch — A1Ch SP2BRGH A9Ch — B1Ch — B9Ch —
81Dh NVMDATH 89Dh — 91Dh — 99Dh — A1Dh RC2STA A9Dh — B1Dh — B9Dh —
81Eh NVMCON1 89Eh — 91Eh — 99Eh — A1Eh TX2STA A9Eh — B1Eh — B9Eh —
81Fh NVMCON2 89Fh — 91Fh ZCDCON 99Fh — A1Fh BAUD2CON A9Fh — B1Fh — B9Fh —
820h General 8A0h General 920h General 9A0h General A20h General AA0h General B20h General BA0h General
Purpose Purpose Purpose Purpose Purpose Purpose Purpose Purpose
Register Register Register Register Register Register Register Register
86Fh 80 Bytes(3) 8EFh 80 Bytes(3) 96Fh 80 Bytes(3) 9EFh 80 Bytes(3) A6Fh 80 Bytes(3) AEFh 80 Bytes(3) B6Fh 80 Bytes(3) BEFh 80 Bytes(3)
870h Common RAM 8F0h Common RAM 970h Common RAM 9F0h Common RAM A70h Common RAM AF0h Common RAM B70h Common RAM BF0h Common RAM
Accesses Accesses Accesses Accesses Accesses Accesses Accesses Accesses
87Fh 70h-7Fh 8FFh 70h-7Fh 97Fh 70h-7Fh 9FFh 70h-7Fh A7Fh 70h-7Fh AFFh 70h-7Fh B7Fh 70h-7Fh BFFh 70h-7Fh

Note 1: Unimplemented locations read as ‘0’.


2: Register not implemented on LF devices.
3: Present only in PIC16(L)F15356/76/86.
DS40001866B-page 58
TABLE 4-7: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANK 24-31
 2016-2018 Microchip Technology Inc.

BANK 24 BANK 25 BANK 26 BANK 27 BANK 28 BANK 29 BANK 30 BANK 31


C00h C80h D00h D80h E00h E80h F00h F80h
Core Registers Core Registers Core Registers Core Registers Core Registers Core Registers Core Registers Core Registers
(Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3)
C0Bh C8Bh D0Bh D8Bh E0Bh E8Bh F0Bh F8Bh
C0Ch C8Ch D0Ch

Unimplemented Unimplemented
Read as ‘0’ Read as ‘0’

Unimplemented Unimplemented Unimplemented Unimplemented Unimplemented Unimplemented

PIC16(L)F15356/75/76/85/86
Read as ‘0’ Read as ‘0’ Read as ‘0’ Read as ‘0’ Read as ‘0’ Read as ‘0’

C1Fh C9Fh
C20h CA0h

General General
Purpose Purpose
Register Register
80 Bytes(1) 80 Bytes(1)

C6Fh CEFh D6Fh DEFh E6Fh EEFh F6Fh FEFh


C70h CF0h D70h DF0h E70h EF0h F70h FF0h
Accesses Accesses Accesses Accesses Accesses Accesses Accesses Accesses
70h – 7Fh 70h – 7Fh 70h – 7Fh 70h – 7Fh 70h – 7Fh 70h – 7Fh 70h – 7Fh 70h – 7Fh
CFFh CFFh D7Fh DFFh E7Fh EFFh F7Fh FFFh

Legend: = Unimplemented data memory locations, read as ‘0’.


Note 1: Present only in PIC16(L)F15356/76/86.
DS40001866B-page 59
TABLE 4-8: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 56-63
 2016-2018 Microchip Technology Inc.

BANK 56 BANK 57 BANK 58 BANK 59 BANK 60 BANK 61 BANK 62 BANK 63


1C00h 1C80h 1D00h 1D80h 1E00h 1E80h 1F00h 1F80h
Core Register Core Register Core Register Core Register Core Register Core Register Core Register Core Register
(Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3) (Table 4-3)
1C0Bh 1C8Bh 1D0Bh 1D8Bh 1E0Bh 1E8Bh 1F0Bh 1F8Bh
1C0Ch — 1C8Ch — 1D0Ch — 1D8Ch — 1E0Ch 1E8Ch 1F0Ch 1F8Ch
1C0Dh — 1C8Dh — 1D0Dh — D8Dh1 —
1C0Eh — 1C8Eh — 1D0Eh — 1D8Eh —
1C0Fh — 1C8Fh — 1D0Fh — 1D8Fh —
1C10h — 1C90h — 1D10h — 1D90h —
1C11h — 1C91h — 1D11h — 1D91h —
1C12h — 1C92h — 1D12h — 1D92h —
1C13h — 1C93h — 1D13h — 1D93h —
1C14h — 1C94h — 1D14h — 1D94h —
1C15h — 1C95h — 1D15h — 1D95h —
1C16h — 1C96h — 1D16h — 1D96h —
1C17h — 1C97h — 1D17h — 1D97h — CLC Controls nnnPPS Controls RxyPPS Controls
(See Table 4-9 for
1C18h — 1C98h — 1D18h — 1D98h — (See Table 4-9 for (See Table 4-9 for (See Table 4-9 for register mapping

PIC16(L)F15356/75/76/85/86
1C19h — 1C99h — 1D19h — 1D99h — register mapping register mapping register mapping details)
1C1Ah — 1C9Ah — 1D1Ah — 1D9Ah — details) details) details)
1C1Bh — 1C9Bh — 1D1Bh — 1D9Bh —
1C1Ch — 1C9Ch — 1D1Ch — 1D9Ch —
1C1Dh — 1C9Dh — 1D1Dh — 1D9Dh —
1C1Eh — 1C9Eh — 1D1Eh — 1D9Eh —
1C1Fh — 1C9Fh — 1D1Fh — 1D9Fh —
1C20h 1CA0h 1D20h 1DA0h

Unimplemented Unimplemented Unimplemented Unimplemented


Read as ‘0’ Read as ‘0’ Read as ‘0’ Read as ‘0’

1C6Fh 1CEFh 1D6Fh 1DEFh 1E6Fh 1EEFh 1F6Fh 1FEFh


1C70h Common RAM 1CF0h Common RAM 1D70h Common RAM 1DF0h Common RAM 1E70h Common RAM 1EF0h Common RAM 1F70h Common RAM 1FF0h Common RAM
Accesses Accesses Accesses Accesses Accesses Accesses Accesses Accesses
1C7Fh 70h-7Fh 1CFFh 70h-7Fh 1D7Fh 70h-7Fh 1DFFh 70h-7Fh 1E7Fh 70h-7Fh 1EFFh 70h-7Fh 1F7Fh 70h-7Fh 1FFFh 70h-7Fh

Note 1: Unimplemented locations read as ‘0’.


2: The banks 32-55 have been omitted from the tables in the data sheet since the banks have unimplemented registers.
DS40001866B-page 60
PIC16(L)F15356/75/76/85/86

TABLE 4-9: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 60, 61, 62, AND 63
Bank 60 Bank 61 Bank 62 Bank 63
— (2) — 1F8Ch —
1E0Ch 1E8Ch RF7PPS 1F0Ch
1E0Dh — 1E8Dh — 1F0Dh — 1F8Dh —
1E0Eh — 1E8Eh — 1F0Eh — 1F8Eh —
1E0Fh CLCDATA 1E8Fh PPSLOCK 1F0Fh — 1F8Fh —
1E10h CLC1CON 1E90h INTPPS 1F10h RA0PPS 1F90h —
1E11h CLC1POL 1E91h T0CKIPPS 1F11h RA1PPS 1F91h —
1E12h CLC1SEL0 1E92h T1CKIPPS 1F12h RA2PPS 1F92h —
1E13h CLC1SEL1 1E93h T1GPPS 1F13h RA3PPS 1F93h —
1E14h CLC1SEL2 1E94h — 1F14h RA4PPS 1F94h —
1E15h CLC1SEL3 1E95h — 1F15h RA5PPS 1F95h —
1E16h CLC1GLS0 1E96h — 1F16h RA6PPS 1F96h —
1E17h CLC1GLS1 1E97h — 1F17h RA7PPS 1F97h —
1E18h CLC1GLS2 1E98h — 1F18h RB0PPS 1F98h —
1E19h CLC1GLS3 1E99h — 1F19h RB1PPS 1F99h —
1E1Ah CLC2CON 1E9Ah — 1F1Ah RB2PPS 1F9Ah —
1E1Bh CLC2POL 1E9Bh — 1F1Bh RB3PPS 1F9Bh —
1E1Ch CLC2SEL0 1E9Ch T2INPPS 1F1Ch RB4PPS 1F9Ch —
1E1Dh CLC2SEL1 1E9Dh — 1F1Dh RB5PPS 1F9Dh —
1E1Eh CLC2SEL2 1E9Eh — 1F1Eh RB6PPS 1F9Eh —
1E1Fh CLC2SEL3 1E9Fh — 1F1Fh RB7PPS 1F9Fh —
1E20h CLC2GLS0 1EA0h — 1F20h RC0PPS 1FA0h —
1E21h CLC2GLS1 1EA1h CCP1PPS 1F21h RC1PPS 1FA1h —
1E22h CLC2GLS2 1EA2h CCP2PPS 1F22h RC2PPS 1FA2h —
1E23h CLC2GLS3 1EA3h — 1F23h RC3PPS 1FA3h —
1E24h CLC3CON 1EA4h — 1F24h RC4PPS 1FA4h —
1E25h CLC3POL 1EA5h — 1F25h RC5PPS 1FA5h —
1E26h CLC3SEL0 1EA6h — 1F26h RC6PPS 1FA6h —
1E27h CLC3SEL1 1EA7h — 1F27h RC7PPS 1FA7h —
1E28h CLC3SEL2 1EA8h — 1F28h RD0PPS(1) 1FA8h —

1E29h CLC3SEL3 1EA9h — 1F29h RD1PPS(1) 1FA9h —


1E2Ah CLC3GLS0 1EAAh — 1F2Ah RD2PPS(1) 1FAAh —

1E2Bh CLC3GLS1 1EABh — 1F2Bh RD3PPS(1) 1FABh —

1E2Ch CLC3GLS2 1EACh — 1F2Ch RD4PPS(1) 1FACh —

1E2Dh CLC3GLS3 1EADh — 1F2Dh RD5PPS(1) 1FADh —

1E2Eh CLC4CON 1EAEh — 1F2Eh RD6PPS(1) 1FAEh —


— (1) —
1E2Fh CLC4POL 1EAFh 1F2Fh RD7PPS 1FAFh
1E30h CLC4SEL0 1EB0h — 1F30h RE0PPS(1) 1FB0h —
(1) —
1E31h CLC4SEL1 1EB1h CWG1PPS 1F31h RE1PPS 1FB1h
1E32h CLC4SEL2 1EB2h — 1F32h RE2PPS(1) 1FB2h —
1E33h CLC4SEL3 1EB3h — 1F33h — 1FB3h —
1E34h CLC4GLS0 1EB4h — 1F34h — 1FB4h —
1E35h CLC4GLS1 1EB5h — 1F35h — 1FB5h —
1E36h CLC4GLS2 1EB6h — 1F36h — 1FB6h —
1E37h CLC4GLS3 1EB7h — 1F37h — 1FB7h —
1E38h RF0PPS(2) 1EB8h — 1F38h ANSELA 1FB8h —
(2) — —
1E39h RF1PPS 1EB9h 1F39h WPUA 1FB9h
1E3Ah RF2PPS(2) 1EBAh — 1F3Ah ODCONA 1FBAh —

1E3Bh RF3PPS(2) 1EBBh CLCIN0PPS 1F3Bh SLRCONA 1FBBh —

1E3Ch RF4PPS(2) 1EBCh CLCIN1PPS 1F3Ch INLVLA 1FBCh —

1E3Dh RF5PPS(2) 1EBDh CLCIN2PPS 1F3Dh IOCAP 1FBDh —

1E3Eh RF6PPS(2) 1EBEh CLCIN3PPS 1F3Eh IOCAN 1FBEh —

Legend: = Unimplemented data memory locations, read as ‘0’


Note 1: Present only on PIC16(L)F15375/76/85/86.
2: Present only on PIC16(L)F15385/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 61


PIC16(L)F15356/75/76/85/86
TABLE 4-9: PIC16(L)F15356/75/76/85/86 MEMORY MAP, BANKS 60, 61, 62, AND 63
Bank 60 Bank 61 Bank 62 Bank 63
1E3Fh RE7PPS(2) 1EBFh — 1F3Fh IOCAF 1FBFh —
1E40h — 1EC0h — 1F40h — 1FC0h —
1E41h — 1EC1h — 1F41h — 1FC1h —
1E42h — 1EC2h — 1F42h — 1FC2h —
1E43h — 1EC3h ADACTPPS 1F43h ANSELB 1FC3h —
1E44h — 1EC4h — 1F44h WPUB 1FC4h —
1E45h — 1EC5h SSP1CLKPPS 1F45h ODCONB 1FC5h —
1E46h — 1EC6h SSP1DATPPS 1F46h SLRCONB 1FC6h —
1E47h — 1EC7h SSP1SSPPS 1F47h INLVLB 1FC7h —
1E48h — 1EC8h SSP2CLKPPS 1F48h IOCBP 1FC8h —
1E49h — 1EC9h SSP2DATPPS 1F49h IOCBN 1FC9h —
1E4Ah — 1ECAh SSP2SSPPS 1F4Ah IOCBF 1FCAh —
1E4Bh — 1ECBh RX1DTPPS 1F4Bh — 1FCBh —
1E4Ch — 1ECCh TX1CKPPS 1F4Ch — 1FCCh —
1E4Dh — 1ECDh RX2DTPPS 1F4Dh — 1FCDh —
1E4Eh — 1ECEh TX2CKPPS 1F4Eh ANSELC 1FCEh —
1E4Fh — 1ECFh — 1F4Fh WPUC 1FCFh —
1E50h ANSELF(2) 1ED0h — 1F50h ODCONC 1FD0h —

1E51h WPUF(2) 1ED1h — 1F51h SLRCONC 1FD1h —

1E52h ODCONF(2) 1ED2h — 1F52h INLVLC 1FD2h —

1E53h SLRCONF(2) 1ED3h — 1F53h IOCCP 1FD3h —

1E54h INLVLF(2) 1ED4h — 1F54h IOCCN 1FD4h —


1E55h — 1ED5h — 1F55h IOCCF 1FD5h —
1E56h — 1ED6h — 1F56h — 1FD6h —
1E57h — 1ED7h — 1F57h — 1FD7h —
1E58h — 1ED8h — 1F58h — 1FD8h —
1E59h — 1ED9h — 1F59h ANSELD(1) 1FD9h —
1E5Ah — 1EDAh — 1F5Ah WPUD(1) 1FDAh —

1E5Bh — 1EDBh — 1F5Bh ODCOND(1) 1FDBh —


— — (1) —
1E5Ch 1EDCh 1F5Ch SLRCOND 1FDCh
— — (1) —
1E5Dh 1EDDh 1F5Dh INLVLD 1FDDh
1E5Eh — 1EDEh — 1F5Eh — 1FDEh —
1E5Fh — 1EDFh — 1F5Fh — 1FDFh —
1E60h — 1EE0h — 1F60h — 1FE0h —
1E61h — 1EE1h — 1F61h — 1FE1h —
1E62h — 1EE2h — 1F62h — 1FE2h —
1E63h — 1EE3h — 1F63h — 1FE3h BSR_ICDSHAD
1E64h — 1EE4h — 1F64h ANSELE(1) 1FE4h STATUS_SHAD
1E65h — 1EE5h — 1F65h WPUE 1FE5h WREG_SHAD
1E66h — 1EE6h — 1F66h ODCONE(1) 1FE6h BSR_SHAD
1E67h — 1EE7h — 1F67h SLRCONE(1) 1FE7h PCLATH_SHAD
1E68h — 1EE8h — 1F68h INLVLE 1FE8h FSR0L_SHAD
1E69h — 1EE9h — 1F69h IOCEP 1FE9h FSR0H_SHAD
1E6Ah — 1EEAh — 1F6Ah IOCEN 1FEAh FSR1L_SHAD
1E6Bh — 1EEBh — 1F6Bh IOCEF 1FEBh FSR1H_SHAD
1E6Ch — 1EECh — 1F6Ch — 1FECh —
1E6Dh — 1EEDh — 1F6Dh — 1FEDh STKPTR
1E6Eh — 1EEEh — 1F6Eh — 1FEEh TOSL
1E6Fh — 1EEFh — 1F6Fh — 1FEFh TOSH

Legend: = Unimplemented data memory locations, read as ‘0’


Note 1: Present only on PIC16(L)F15375/76/85/86.
2: Present only on PIC16(L)F15385/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 62


PIC16(L)F15356/75/76/85/86

TABLE 4-10: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (ALL BANKS)
Bank Offset Value on: Value on:
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Bank 0-Bank 63 POR, BOR MCLR

All Banks
Addressing this location uses contents of FSR0H/FSR0L to address data memory (not a
x00h or x80h INDF0 xxxx xxxx xxxx xxxx
physical register)
Addressing this location uses contents of FSR1H/FSR1L to address data memory (not a
x01h or x81h INDF1 xxxx xxxx xxxx xxxx
physical register)
x02h or x82h PCL PCL 0000 0000 0000 0000
x03h or x83h STATUS — — — TO PD Z DC C ---1 1000 ---q quuu
x04h or x84h FSR0L FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
x05h or x85h FSR0H FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
x06h or x86h FSR1L FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
x07h or x87h FSR1H FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
x08h or x88h BSR — — BSR<5:0> --00 0000 --00 0000
x09h or x89h WREG Working Register 0000 0000 uuuu uuuu
x0Ah or x8Ah PCLATH — Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
x0Bh or x8Bh INTCON GIE PEIE — — — — — INTEDG 00-- ---1 00-- ---1
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations
unimplemented, read as ‘0’.
Note 1: These Registers can be accessed from any bank.

 2016-2018 Microchip Technology Inc. DS40001866B-page 63


 2016-2018 Microchip Technology Inc.

TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63


Value on: Value on:
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 0

CPU CORE REGISTERS; see Table 4-10 for specifics

00Ch PORTA RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 xxxx xxxx uuuu uuuu
00Dh PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx uuuu uuuu
00Eh PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 xxxx xxxx uuuu uuuu
00Fh PORTD(1) RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx xxxx uuuu uuuu
010h PORTE — — — — RE3 RE2(1) RE1(1) RE0(1) ---- xxxx ---- uuuu
011h PORTF(2) RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0 xxxx xxxx uuuu uuuu
012h TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 1111 1111 1111 1111
013h TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 1111 1111 1111 1111
014h TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 1111 1111 1111 1111

PIC16(L)F15356/75/76/85/86
015h TRISD(1) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 1111 1111 1111 1111
016h TRISE — — — — —(3) TRISE2(1) TRISE1(1) TRISE0(1) ---- 1111 ---- 1111
(2)
017h TRISF TRISF7 TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0 1111 1111 1111 1111
018h LATA LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 xxxx xxxx uuuu uuuu
019h LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 xxxx xxxx uuuu uuuu
01Ah LATC LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0 xxxx xxxx uuuu uuuu
01Bh LATD(1) LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 xxxx xxxx uuuu uuuu
01Ch LATE — — — — — LATE2(1) LATE1(1) LATE0(1) ---- -xxx ---- -uuu
(2)
01Dh LATF LATF7 LATF6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0 xxxx xxxx uuuu uuuu
01Eh — Unimplemented — —
01Fh — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
Note 1: Present only in PIC16(L)F15375/76/85/86.
2: Present only in PIC16(L)F15385/86.
3: Unimplemented, read as ‘1’.
DS40001866B-page 64
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 1

CPU CORE REGISTERS; see Table 4-3 for specifics

08Ch
— — Unimplemented — —
09Ah
09Bh ADRESL ADC Result Register Low xxxx xxxx uuuu uuuu
09Ch ADRESH ADC Result Register High xxxx xxxx uuuu uuuu
09Dh ADCON0 CHS<5:0> GO/DONE ADON 0000 0000 0000 0000
09Eh ADCON1 ADFM ADCS<2:0> — — ADPREF<1:0> 0000 --00 0000 --00
09Fh ADACT — — — ADACT<4:0> ---0 0000 ---0 0000
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 65
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 2

CPU CORE REGISTERS; see Table 4-3 for specifics

10Ch
— — Unimplemented — —
118h
119h RC1REG EUSART Receive Data Register 0000 0000 0000 0000
11Ah TX1REG EUSART Transmit Data Register 0000 0000 0000 0000
11Bh SP1BRGL SP1BRG<7:0> 0000 0000 0000 0000
11Ch SP1BRGH SP1BRG<15:8> 0000 0000 0000 0000
11Dh RC1STA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 0000 0000 0000
11Eh TX1STA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010
11Fh BAUD1CON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 01-0 0-00 01-0 0-00

PIC16(L)F15356/75/76/85/86
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 66
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 3

CPU CORE REGISTERS; see Table 4-3 for specifics

18Ch SSP1BUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx xxxx xxxx
18Dh SSP1ADD ADD<7:0> 0000 0000 0000 0000
18Eh SSP1MSK MSK<7:0> 1111 1111 1111 1111
18Fh SSP1STAT SMP CKE D/A P S R/W UA BF 0000 0000 0000 0000
190h SSP1CON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000
191h SSP1CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 0000 0000 0000 0000
192h SSP1CON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 0000 0000 0000 0000
193h — Unimplemented — —
194h — Unimplemented — —

PIC16(L)F15356/75/76/85/86
195h — Unimplemented — —
196h SSP2BUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx xxxx xxxx
197h SSP2ADD ADD<7:0> 0000 0000 0000 0000
198h SSP2MSK MSK<7:0> 1111 1111 1111 1111
199h SSP2STAT SMP CKE D/A P S R/W UA BF 0000 0000 0000 0000
19Ah SSP2CON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000
19Bh SSP2CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 0000 0000 0000 0000
19Ch SSP2CON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 0000 0000 0000 0000
19Dh — Unimplemented — —
19Eh — Unimplemented — —
19Fh — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 67
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 4

CPU CORE REGISTERS; see Table 4-3 for specifics

20Ch TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register 0000 0000 uuuu uuuu
20Dh TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register 0000 0000 uuuu uuuu
20Eh T1CON — — CKPS<1:0> — SYNC RD16 ON --00 -000 --uu -u0u
20Fh T1GCON GE GPOL GTM GSPM GGO/DONE GVAL — — 0000 0x-- uuuu ux--
210h T1GATE — — — GSS<4:0> ---0 0000 ---u uuuu
211h T1CLK — — — — CS<3:0> ---- 0000 ---- uuuu
212h
— — Unimplemented — —
21Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 68
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 5

CPU CORE REGISTERS; see Table 4-3 for specifics

28Ch T2TMR Holding Register for the 8-bit TMR2 Register 0000 0000 0000 0000
28Dh T2PR TMR2 Period Register 1111 1111 1111 1111
28Eh T2CON ON CKPS<2:0> OUTPS<3:0> 0000 0000 0000 0000
28Fh T2HLT PSYNC CKPOL CKSYNC MODE<4:0> 0000 0000 0000 0000
290h T2CLKCON — — — — CS<3:0> ---- 0000 ---- 0000
291h T2RST — — — — RSEL<3:0> ---- 0000 ---- 0000
292h
— — Unimplemented — —
29Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 69
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 6

CPU CORE REGISTERS; see Table 4-3 for specifics

30Ch CCPR1L Capture/Compare/PWM Register 1 (LSB) xxxx xxxx uuuu uuuu


30Dh CCPR1H Capture/Compare/PWM Register 1 (MSB) xxxx xxxx uuuu uuuu
30Eh CCP1CON EN — OUT FMT MODE<3:0> 0-00 0000 0-00 0000
30Fh CCP1CAP — — — — — CTS<2:0> ---- -000 ---- -000
310h CCPR2L Capture/Compare/PWM Register 2 (LSB) xxxx xxxx uuuu uuuu
311h CCPR2H Capture/Compare/PWM Register 2 (MSB) xxxx xxxx uuuu uuuu
312h CCP2CON EN — OUT FMT MODE<3:0> 0-00 0000 0-00 0000
313h CCP2CAP — — — — — CTS<2:0> ---- -000 ---- -000
314h PWM3DCL DC<1:0> — — — — — — xx-- ---- uu-- ----

PIC16(L)F15356/75/76/85/86
315h PWM3DCH DC<9:0> xxxx xxxx uuuu uuuu
316h PWM3CON EN — OUT POL — — — — 0-00 ---- 0-00 ----
317h — Unimplemented — —
318h PWM4DCL DC<1:0> — — — — — — xx-- ---- uu-- ----
319h PWM4DCH DC<9:0> xxxx xxxx uuuu uuuu
31Ah PWM4CON EN — OUT POL — — — — 0-00 ---- 0-00 ----
31Bh — Unimplemented — —
31Ch PWM5DCL DC<1:0> — — — — — — xx-- ---- uu-- ----
31Dh PWM5DCH DC<9:0> xxxx xxxx uuuu uuuu
31Eh PWM5CON EN — OUT POL — — — — 0-00 ---- 0-00 ----
31Fh — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 70
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 7

CPU CORE REGISTERS; see Table 4-3 for specifics

38Ch PWM6DCL DC<1:0> — — — — — — xx-- ---- uu-- ----


38Dh PWM6DCH DC<9:0> xxxx xxxx uuuu uuuu
38Eh PWM6CON EN — OUT POL — — — — 0-00 ---- 0-00 ----
38Fh
— — Unimplemented — —
39Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 71
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 8-10

CPU CORE REGISTERS; see Table 4-3 for specifics

x0Ch/
x8Ch
— — Unimplemented
x1Fh/
x9Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 72
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 11

CPU CORE REGISTERS; see Table 4-3 for specifics

58Ch NCO1ACCL NCO1ACC<7:0> 0000 0000 0000 0000


58Dh NCO1ACCH NCO1ACC<15:8> 0000 0000 0000 0000
58Eh NCO1ACCU — — — — NCO1ACC<19:16> ---- 0000 ---- 0000
58Fh NCO1INCL NCO1INC<7:0> 0000 0001 0000 0001
590h NCO1INCH NCO1INC<15:8> 0000 0000 0000 0000
591h NCO1INCU — — — — NCO1INC<19:16> ---- 0000 ---- 0000
592h NCO1CON N1EN — N1OUT N1POL — — — N1PFM 0-00 ---0 0-00 ---0
593h NCO1CLK N1PWS<2:0> — — N1CKS<2:0> 000- -000 000- -000
594h — Unimplemented — —

PIC16(L)F15356/75/76/85/86
595h — Unimplemented — —
596h — Unimplemented — —
597h — Unimplemented — —
598h — Unimplemented — —
599h — Unimplemented — —
59Ah — Unimplemented — —
59Bh — Unimplemented — —
59Ch TMR0L Holding Register for the Least Significant Byte of the 16-bit TMR0 Register 0000 0000 0000 0000
59Dh TMR0H Holding Register for the Most Significant Byte of the 16-bit TMR0 Register 1111 1111 1111 1111
59Eh T0CON0 T0EN — T0OUT T016BIT T0OUTPS<3:0> 0-00 0000 0-00 0000
59Fh T0CON1 T0CS<2:0> T0ASYNC T0CKPS<3:0> 0000 0000 0000 0000
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 73
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 12

CPU CORE REGISTERS; see Table 4-3 for specifics

60Ch CWG1CLKCON — — — — — — — CS ---- ---0 ---- ---0


60Dh CWG1DAT — — — — DAT<3:0> ---- 0000 ---- 0000
60Eh CWG1DBR — — DBR<5:0> --00 0000 --00 0000
60Fh CWG1DBF — — DBF<5:0> --00 0000 --00 0000
610h CWG1CON0 EN LD — — — MODE<2:0> 00-- -000 00-- -000
611h CWG1CON1 — — IN — POLD POLC POLB POLA --x- 0000 --u- 0000
612h CWG1AS0 SHUTDOWN REN LSBD<2:0> LSAC<2:0> — — 0001 01-- 0001 01--
613h CWG1AS1 — — — AS4E AS3E AS2E AS1E AS0E ---0 0000 ---u 0000
614h CWG1STR OVRD OVRC OVRB OVRA STRD STRC STRB STRA 0000 0000 0000 0000

PIC16(L)F15356/75/76/85/86
615h
— — Unimplemented — —
61Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 74
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 13

CPU CORE REGISTERS; see Table 4-3 for specifics

68Ch
— — Unimplemented — —
69Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 75
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 14

CPU CORE REGISTERS; see Table 4-3 for specifics

70Ch PIR0 — — TMR0IF IOCIF — — — INTF --00 ---0 --00 ---0


70Dh PIR1 OSFIF CSWIF — — — — — ADIF 00-- --00 00-- --00
70Eh PIR2 — ZCDIF — — — — C2IF C1IF -0-- --00 -0-- --00

70Fh PIR3 RC2IF TX2IF RC1IF TX1IF BCL2IF SSP2IF BCL1IF SSP1IF 0000 0000 0000 0000
710h PIR4 — — — — — — TMR2IF TMR1IF ---- --00 ---- --00
711h PIR5 CLC4IF CLC3IF CLC2IF CLC1IF — — — TMR1GIF 0000 ---0 0000 ---0
712h PIR6 — — — — — — CCP2IF CCP1IF ---- --00 ---- --00
713h PIR7 — — NVMIF NCO1IF — — — CWG1IF --00 ---0 --00 ---0
714h — Unimplemented — —

PIC16(L)F15356/75/76/85/86
715h — Unimplemented — —
716h PIE0 — — TMR0IE IOCIE — — — INTE --00 ---0 --00 ---0
717h PIE1 OSFIE CSWIE — — — — — ADIE 00-- --00 00-- --00
718h PIE2 — ZCDIE — — — — C2IE C1IE -0-- --00 -0-- --00

719h PIE3 RC2IE TX2IE RC1IE TX1IE BCL2IE SSP2IE BCL1IE SSP1IE 0000 0000 0000 0000
71Ah PIE4 — — — — — — TMR2IE TMR1IE ---- --00 ---- --00
71Bh PIE5 CLC4IE CLC3IE CLC2IE CLC1IE — — — TMR1GIE 0000 ---0 0000 ---0
71Ch PIE6 — — — — — — CCP2IE CCP1IE ---- --00 ---- --00
71Dh PIE7 — — NVMIE NCO1IE — — — CWG1IE --00 ---0 --00 ---0
71Eh — Unimplemented — —
71Fh — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 76
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 15

CPU CORE REGISTERS; see Table 4-3 for specifics

78Ch
— — Unimplemented — —
795h
796h PMD0 SYSCMD FVRMD — — — NVMMD CLKRMD IOCMD 00-- -000 00-- -000
797h PMD1 NCO1MD — — — — TMR2MD TMR1MD TMR0MD 0--- -000 0--- -000
798h PMD2 — DAC1MD ADCMD — — CMP2MD CMP1MD ZCDMD -00- -000 -00- -000
799h PMD3 — — PWM6MD PWM5MD PWM4MD PWM3MD CCP2MD CCP1MD --00 0000 --00 0000
79Ah PMD4 UART2MD UART1MD MSSP2MD MSSP1MD — — — CWG1MD 0000 ---0 0000 ---0
79Bh PMD5 — — — CLC4MD CLC3MD CLC2MD CLC1MD — ---0 000- ---0 000-
79Ch — Unimplemented — —

PIC16(L)F15356/75/76/85/86
79Dh — Unimplemented — —
79Eh — Unimplemented — —
79Fh — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 77
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 16

CPU CORE REGISTERS; see Table 4-3 for specifics

80Ch WDTCON0 — — WDTPS<4:0> SWDTEN --qq qqq0 --qq qqq0

80Dh WDTCON1 — WDTCS<2:0> — WINDOW<2:0> -qqq -qqq -qqq -qqq

80Eh WDTPSL PSCNT<7:0> 0000 0000 0000 0000


80Fh WDTPSH PSCNT<15:8> 0000 0000 0000 0000
810h WDTTMR — WDTTMR<3:0> STATE PSCNT17 PSCNT16 xxxx x000 xxxx x000
811h BORCON SBOREN — — — — — — BORRDY 1--- ---q u--- ---u
812h VREGCON — — — — — — VREGPM(1) — ---- --0- ---- --0-
813h PCON0 STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR 0011 110q qqqq qquu
814h PCON1 — — — — — — MEMV — ---- --1- ---- --u-

PIC16(L)F15356/75/76/85/86
815h — Unimplemented — —
816h — Unimplemented — —
817h — Unimplemented — —
818h — Unimplemented — —
819h — Unimplemented — —
81Ah NVMADRL NVMADR<7:0> xxxx xxxx uuuu uuuu
81Bh NVMADRH — NVMADR<14:8> -xxx xxxx -uuu uuuu
81Ch NVMDATL NVMDAT<7:0> 0000 0000 0000 0000
81Dh NVMDATH — — NVMDAT<13:8> --00 0000 --00 0000
81Eh NVMCON1 — NVMREGS LWLO FREE WRERR WREN WR RD -000 x000 -000 q000
81Fh NVMCON2 NVMCON2<7:0> xxxx xxxx uuuu uuuu
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
Note 1: Present only on PIC16F15356/75/76/85/86.
DS40001866B-page 78
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 17

CPU CORE REGISTERS; see Table 4-3 for specifics

88Ch CPUDOZE IDLEN DOZEN ROI DOE — DOZE<2:0> 0000 -000 u000 -000
88Dh OSCCON1 — NOSC<2:0> NDIV<3:0> -qqq 0000 -qqq 0000
88Eh OSCCON2 — COSC<2:0> CDIV<3:0> -qqq qqqq -qqq qqqq
88Fh OSCCON3 CSWHOLD SOSCPWR — ORDY NOSCR — — — 00-0 0--- 00-0 0---
890h OSCSTAT EXTOR HFOR MFOR LFOR SOR ADOR — PLLR q000 qq-0 qqqq qq-q
891h OSCEN EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN — — 0000 00-- 0000 00--
892h OSCTUNE — — HFTUN<5:0> --10 0000 --10 0000
893h OSCFRQ — — — — — HFFRQ<2:0> ---- -qqq ---- -qqq
894h — Unimplemented — —

PIC16(L)F15356/75/76/85/86
895h CLKRCON CLKREN — — CLKRDC<1:0> CLKRDIV<2:0> 0--x xxxx 0--u uuuu
896h CLKRCLK — — — — CLKRCLK<3:0> ---- 0000 ---- 0000
897h
— — Unimplemented — —
89Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 79
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 18

CPU CORE REGISTERS; see Table 4-3 for specifics

90Ch FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 0x00 xxxx 0q00 uuuu
90Dh — Unimplemented — —
90Eh DAC1CON0 EN — OE1 OE2 PSS<1:0> — NSS 0-00 00-0 0-00 00-0
90Fh DAC1CON1 — — — DAC1R<4:0> ---0 0000 ---0 0000
910h
— — Unimplemented — —
91Eh
91Fh ZCDCON ZCDSEN — ZCDOUT ZCDPOL — — ZCDINTP ZCDINTN 0-x0 --00 0-x0 --00
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 80
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 19

CPU CORE REGISTERS; see Table 4-3 for specifics

98Ch — Unimplemented — —
98Dh — Unimplemented — —
98Eh — Unimplemented — —
98Fh CMOUT — — — — — — MC2OUT MC1OUT ---- --00 ---- --00
990h CM1CON0 EN OUT — POL — — HYS SYNC 00-0 --00 00-0 --00
991h CM1CON1 — — — — — — INTP INTN ---- --00 ---- --00
992h CM1NCH — — — — — NCH<2:0> ---- -000 ---- -000
993h CM1PCH — — — — — PCH<2:0> ---- -000 ---- -000
994h CM2CON0 EN OUT — POL — — HYS SYNC 00-0 --00 00-0 --00

PIC16(L)F15356/75/76/85/86
995h CM2CON1 — — — — — — INTP INTN ---- --00 ---- --00
996h CM2NCH — — — — — NCH<2:0> ---- -000 ---- -000
997h CM2PCH — — — — — PCH<2:0> ---- -000 ---- -000
998h
— — Unimplemented — —
99Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 81
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 20

CPU CORE REGISTERS; see Table 4-3 for specifics

A0Ch
— — Unimplemented — —
A18h
A19h RC2REG RC2REG<7:0> 0000 0000 0000 0000
A1Ah TX2REG TX2REG<7:0> 0000 0000 0000 0000
A1Bh SP2BRGL SP2BRGL<7:0> 0000 0000 0000 0000
A1Ch SP2BRGH SP2BRGH<7:0> 0000 0000 0000 0000
A1Dh RC2STA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 0000 0000 0000
A1Eh TX2STA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010
A1Fh BAUD2CON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 01-0 0-00 01-0 0-00

PIC16(L)F15356/75/76/85/86
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 82
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 21-59

CPU CORE REGISTERS; see Table 4-3 for specifics

x0Ch/
x8Ch
— — Unimplemented — —
x1Fh/
x9Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.

PIC16(L)F15356/75/76/85/86
DS40001866B-page 83
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 60

CPU CORE REGISTERS; see Table 4-3 for specifics

1E0Ch — Unimplemented — —
1E0Dh — Unimplemented — —
1E0Eh — Unimplemented — —
1E0Fh CLCDATA — — — — MLC4OUT MLC3OUT MLC2OUT MLC1OUT ---- xxxx ---- uuuu
1E10h CLCCON LC1EN — LC1OUT LC1INTP LC1INTN LC1MODE<2:0> 0-00 0000 0-00 0000
1E11h CLC1POL LC1POL — — — LC1G4POL LC1G3POL LC1G2POL LC1G1POL 0--- xxxx 0--- uuuu
1E12h CLC1SEL0 — — LC1D1S<5:0> --xx xxxx --uu uuuu
1E13h CLC1SEL1 — — LC1D2S<5:0> --xx xxxx --uu uuuu
1E14h CLC1SEL2 — — LC1D3S<5:0> --xx xxxx --uu uuuu

PIC16(L)F15356/75/76/85/86
1E15h CLC1SEL3 — — LC1D4S<5:0> --xx xxxx --uu uuuu
1E16h CLC1GLS0 LC1G1D4T LC1G4D3N LC1G1D3T LC1G1D3N LC1G1D2T LC1G1D2N LC1G1D1T LC1G1D1N xxxx xxxx uuuu uuuu
1E17h CLC1GLS1 LC1G2D4T LC1G4D3N LC1G2D3T LC1G2D3N LC1G2D2T LC1G2D2N LC1G2D1T LC1G2D1N xxxx xxxx uuuu uuuu
1E18h CLC1GLS2 LC1G3D4T LC1G4D3N LC1G3D3T LC1G3D3N LC1G3D2T LC1G3D2N LC1G3D1T LC1G3D1N xxxx xxxx uuuu uuuu
1E19h CLC1GLS3 LC1G4D4T LC1G4D3N LC1G4D3T LC1G4D3N LC1G4D2T LC1G4D2N LC1G4D1T LC1G4D1N xxxx xxxx uuuu uuuu
1E1Ah CLC2CON LC2EN — LC2OUT LC2INTP LC2INTN LC2MODE<2:0> 0-00 0000 0-00 0000
1E1Bh CLC2POL LC2POL — — — LC2G4POL LC2G3POL LC2G2POL LC2G1POL 0--- xxxx 0--- uuuu
1E1Ch CLC2SEL0 — — LC2D1S<5:0> --xx xxxx --uu uuuu
1E1Dh CLC2SEL1 — — LC2D2S<5:0> --xx xxxx --uu uuuu
1E1Eh CLC2SEL2 — — LC2D3S<5:0> --xx xxxx --uu uuuu
1E1Fh CLC2SEL3 — — LC2D4S<5:0> --xx xxxx --uu uuuu
1E20h CLC2GLS0 LC2G1D4T LC2G4D3N LC2G1D3T LC2G1D3N LC2G1D2T LC2G1D2N LC2G1D1T LC2G1D1N xxxx xxxx uuuu uuuu
1E21h CLC2GLS1 LC2G2D4T LC2G4D3N LC2G2D3T LC2G2D3N LC2G2D2T LC2G2D2N LC2G2D1T LC2G2D1N xxxx xxxx uuuu uuuu
1E22h CLC2GLS2 LC2G3D4T LC2G4D3N LC2G3D3T LC2G3D3N LC2G3D2T LC2G3D2N LC2G3D1T LC2G3D1N xxxx xxxx uuuu uuuu
1E23h CLC2GLS3 LC2G4D4T LC2G4D3N LC2G4D3T LC2G4D3N LC2G4D2T LC2G4D2N LC2G4D1T LC2G4D1N xxxx xxxx uuuu uuuu
1E24h CLC3CON LC3EN — LC3OUT LC3INTP LC3INTN LC3MODE 0-00 0000 0-00 0000
1E25h CLC3POL LC3POL — — — LC3G4POL LC3G3POL LC3G2POL LC3G1POL 0--- xxxx 0--- uuuu
DS40001866B-page 84

1E26h CLC3SEL0 — — LC3D1S<5:0> --xx xxxx --uu uuuu


1E27h CLC3SEL1 — — LC3D2S<5:0> --xx xxxx --uu uuuu
1E28h CLC3SEL2 — — LC3D3S<5:0> --xx xxxx --uu uuuu
1E29h CLC3SEL3 — — LC3D4S<5:0> --xx xxxx --uu uuuu
1E2Ah CLC3GLS0 LC3G1D4T LC3G4D3N LC3G1D3T LC3G1D3N LC3G1D2T LC3G1D2N LC3G1D1T LC3G1D1N xxxx xxxx uuuu uuuu
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 60 (Continued)
1E2Bh CLC3GLS1 LC3G2D4T LC3G4D3N LC3G2D3T LC3G2D3N LC3G2D2T LC3G2D2N LC3G2D1T LC3G2D1N xxxx xxxx uuuu uuuu
1E2Ch CLC3GLS2 LC3G3D4T LC3G4D3N LC3G3D3T LC3G3D3N LC3G3D2T LC3G3D2N LC3G3D1T LC3G3D1N xxxx xxxx uuuu uuuu
1E2Dh CLC3GLS3 LC3G4D4T LC3G4D3N LC3G4D3T LC3G4D3N LC3G4D2T LC3G4D2N LC3G4D1T LC3G4D1N xxxx xxxx uuuu uuuu
1E2Eh CLC4CON LC4EN — LC4OUT LC4INTP LC4INTN LC4MODE<2:0> 0-00 0000 0-00 0000
1E2Fh CLC4POL LC4POL — — — LC4G4POL LC4G3POL LC4G2POL LC4G1POL 0--- xxxx 0--- uuuu
1E30h CLC4SEL0 — — LC4D1S<5:0> --xx xxxx --uu uuuu
1E31h CLC4SEL1 — — LC4D2S<5:0> --xx xxxx --uu uuuu
1E32h CLC4SEL2 — — LC4D3S<5:0> --xx xxxx --uu uuuu
1E33h CLC4SEL3 — — LC4D4S<5:0> --xx xxxx --uu uuuu
1E34h CLC4GLS0 LC4G1D4T LC4G4D3N LC4G1D3T LC4G1D3N LC4G1D2T LC4G1D2N LC4G1D1T LC4G1D1N xxxx xxxx uuuu uuuu
1E35h CLC4GLS1 LC4G2D4T LC4G4D3N LC4G2D3T LC4G2D3N LC4G2D2T LC4G2D2N LC4G2D1T LC4G2D1N xxxx xxxx uuuu uuuu
1E36h CLC4GLS2 LC4G3D4T LC4G4D3N LC4G3D3T LC4G3D3N LC4G3D2T LC4G3D2N LC4G3D1T LC4G3D1N xxxx xxxx uuuu uuuu

PIC16(L)F15356/75/76/85/86
1E37h CLC4GLS3 LC4G4D4T LC4G4D3N LC4G4D3T LC4G4D3N LC4G4D2T LC4G4D2N LC4G4D1T LC4G4D1N xxxx xxxx uuuu uuuu
1E38h RF0PPS(1) — — — RF0PPS<4:0> ---0 0000 ---u uuuu
1E39h RF1PPS(1) — — — RF1PPS<4:0> ---0 0000 ---u uuuu
1E3Ah RF2PPS(1) — — — RF2PPS<4:0> ---0 0000 ---u uuuu
1E3Bh RF3PPS(1) — — — RF3PPS<4:0> ---0 0000 ---u uuuu
1E3Ch RF4PPS(1) — — — RF4PPS<4:0> ---0 0000 ---u uuuu
1E3Dh RF5PPS(1) — — — RF5PPS<4:0> ---0 0000 ---u uuuu
1E3Eh RF6PPS(1) — — — RF6PPS<4:0> ---0 0000 ---u uuuu
1E3Fh RF7PPS(1) — — — RF7PPS<4:0> ---0 0000 ---u uuuu
1E40h
— — Unimplemented — —
1E4Fh
1E50h ANSELF(1) ANSF7 ANSF6 ANSF5 ANSF4 ANSF3 ANSF2 ANSF1 ANSF0 1111 1111 1111 1111
1E51h WPUF(1) WPUF7 WPUF6 WPUF5 WPUF4 WPUF3 WPUF2 WPUF1 WPUF0 0000 0000 0000 0000
1E52h ODCONF(1) ODCF7 ODCF6 ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCFCF0 0000 0000 0000 0000
1E53h SLRCONF(1) SLRF7 SLRF6 SLRF5 SLRF4 SLRF3 SLRF2 SLRF1 SLRF0 1111 1111 1111 1111
1E54h INLVLF(1) INLVLF7 INLVLF6 INLVLF5 INLVLF4 INLVLF3 INLVLF2 INLVLF1 INLVLF0 1111 1111 1111 1111
DS40001866B-page 85

1E55h
— — Unimplemented — —
1E6Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
Note 1: Present only on PIC16(L)F15385/86.
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 61

CPU CORE REGISTERS; see Table 4-3 for specifics

1E8Ch — Unimplemented — —
1E8Dh — Unimplemented — —
1E8Eh — Unimplemented — —
1E8Fh PPSLOCK — — — — — — — PPSLOCKED ---- ---0 ---- ---0
1E90h INTPPS — — INTPPS<5:0> --00 1000 --uu uuuu
1E91h T0CKIPPS — — T0CKIPPS<5:0> --00 0100 --uu uuuu
1E92h T1CKIPPS — — T1CKIPPS<5:0> --01 0000 --uu uuuu
1E93h T1GPPS — — T1GPPS<5:0> --00 1101 --uu uuuu
1E94h
— — Unimplemented — —

PIC16(L)F15356/75/76/85/86
1E9Bh
1E9Ch T2INPPS — — T2INPPS<5:0> --01 0011 --uu uuuu
1E9Dh
— — Unimplemented — —
1EA0h
1EA1h CCP1PPS — — CCP1PPS<5:0> --01 0010 --uu uuuu
1EA2h CCP2PPS — — CCP2PPS<5:0> --01 0001 --uu uuuu
1EA3h
— — Unimplemented — —
1EB0h
1EB1h CWG1PPS — — CWG1PPS<5:0> --00 1000 --uu uuuu
1EB2h
— — Unimplemented — —
1EBAh
1EBBh CLCIN0PPS — — CLCIN0PPS<5:0> --00 0000 --uu uuuu
1EBCh CLCIN1PPS — — CLCIN1PPS<5:0> --00 0001 --uu uuuu
1EBDh CLCIN2PPS — — CLCIN2PPS<5:0> --00 1110 --uu uuuu
1EBEh CLCIN3PPS — — CLCIN3PPS<5:0> --00 1111 --uu uuuu
1EBFh
— — Unimplemented — —
1EC2h
DS40001866B-page 86

1EC3h ADACTPPS — — ADACTPPS<5:0> --001100 --uuuuuu


1EC4h — Unimplemented — —
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 61 (Continued)
1EC5h SSP1CLKPPS — — SSP1CLKPPS<5:0> --01 0011 --uu uuuu
1EC6h SSP1DATPPS — — SSP1DATPPS<5:0> --01 0100 --uu uuuu
1EC7h SSP1SSPPS — — SSP1SSPPS<5:0> --00 0101 --uu uuuu
1EC8h SSP2CLKPPS — — SSP2CLKPPS<5:0> --00 1001 --uu uuuu
1EC9h SSP2DATPPS — — SSP2DATPPS<5:0> --00 1000 --uu uuuu
1ECAh SSP2SSPPS — — SSP2SSPPS<5:0> --00 1000 --uu uuuu
1ECBh RX1DTPPS — — RX1DTPPS<5:0> --01 0111 --uu uuuu
1ECCh TX1CKPPS — — TX1CKPPS<5:0> --01 0110 --uu uuuu
1ECDh RX2DTPPS — — RX2DTPPS<5:0> --00 1111 --uu uuuu
1ECEh TX2CKPPS — — TX2CKPPS<5:0> --00 1110 --uu uuuu
1ECFh
— — Unimplemented — —

PIC16(L)F15356/75/76/85/86
1EEFh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 87
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 62

CPU CORE REGISTERS; see Table 4-3 for specifics

1F0Ch — Unimplemented — —
1F0Dh — Unimplemented — —
1F0Eh — Unimplemented — —
1F0Fh — Unimplemented — —
1F10h RA0PPS — — — RA0PPS<4:0> ---0 0000 ---u uuuu
1F11h RA1PPS — — — RA1PPS<4:0> ---0 0000 ---u uuuu
1F12h RA2PPS — — — RA2PPS<4:0> ---0 0000 ---u uuuu
1F13h RA3PPS — — — RA3PPS<4:0> ---0 0000 ---u uuuu
1F14h RA4PPS — — — RA4PPS<4:0> ---0 0000 ---u uuuu
1F15h RA5PPS — — — RA5PPS<4:0> ---0 0000 ---u uuuu

PIC16(L)F15356/75/76/85/86
1F16h RA6PPS — — — RA6PPS<4:0> ---0 0000 ---u uuuu
1F17h RA7PPS — — — RA7PPS<4:0> ---0 0000 ---u uuuu
1F18h RB0PPS — — — RB0PPS<4:0> ---0 0000 ---u uuuu
1F19h RB1PPS — — — RB1PPS<4:0> ---0 0000 ---u uuuu
1F1Ah RB2PPS — — — RB2PPS<4:0> ---0 0000 ---u uuuu
1F1Bh RB3PPS — — — RB3PPS<4:0> ---0 0000 ---u uuuu
1F1Ch RB4PPS — — — RB4PPS<4:0> ---0 0000 ---u uuuu
1F1Dh RB5PPS — — — RB5PPS<4:0> ---0 0000 ---u uuuu
1F1Eh RB6PPS — — — RB6PPS<4:0> ---0 0000 ---u uuuu
1F1Fh RB7PPS — — — RB7PPS<4:0> ---0 0000 ---u uuuu
1F20h RC0PPS — — — RC0PPS<4:0> ---0 0000 ---u uuuu
1F21h RC1PPS — — — RC1PPS<4:0> ---0 0000 ---u uuuu
1F22h RC2PPS — — — RC2PPS<4:0> ---0 0000 ---u uuuu
1F23h RC3PPS — — — RC3PPS<4:0> ---0 0000 ---u uuuu
1F24h RC4PPS — — — RC4PPS<4:0> ---0 0000 ---u uuuu
1F25h RC5PPS — — — RC5PPS<4:0> ---0 0000 ---u uuuu
1F26h RC6PPS — — — RC6PPS<4:0> ---0 0000 ---u uuuu
DS40001866B-page 88

1F27h RC7PPS — — — RC7PPS<4:0> ---0 0000 ---u uuuu


1F28h RD0PPS(1) — — — RD0PPS<4:0> ---0 0000 ---u uuuu
1F29h RD1PPS(1) — — — RD1PPS<4:0> ---0 0000 ---u uuuu
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
Note 1: Present only on PIC16(L)F15375/76/85/86.
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 62 (Continued)
1F2Ah RD2PPS(1) — — — RD2PPS<4:0> ---0 0000 ---u uuuu
1F2Bh RD3PPS(1) — — — RD3PPS<4:0> ---0 0000 ---u uuuu
1F2Ch RD4PPS(1) — — — RD4PPS<4:0> ---0 0000 ---u uuuu
1F2Dh RD5PPS(1) — — — RD5PPS<4:0> ---0 0000 ---u uuuu
1F2Eh RD6PPS(1) — — — RD6PPS<4:0> ---0 0000 ---u uuuu
1F2Fh RD7PPS(1) — — — RD7PPS<4:0> ---0 0000 ---u uuuu
1F30h RE0PPS(1) — — — RE0PPS<4:0> ---0 0000 ---u uuuu
1F31h RE1PPS(1) — — — RE1PPS<4:0> ---0 0000 ---u uuuu
1F32h RE2PPS(1) — — — RE2PPS<4:0> ---0 0000 ---u uuuu
1F33h
— — Unimplemented — —
1F37h

PIC16(L)F15356/75/76/85/86
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
Note 1: Present only on PIC16(L)F15375/76/85/86.
DS40001866B-page 89
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 62 (Continued)
1F38h ANSELA ANSA7 ANSA6 ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 1111 1111 1111 1111
1F39h WPUA WPUA7 WPUA6 WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0 0000 0000 0000 0000
1F3Ah ODCONA ODCA7 ODCA6 ODCA5 ODCA4 ODCA3 ODCA2 ODCA1 ODCA0 0000 0000 0000 0000
1F3Bh SLRCONA SLRA7 SLRA6 SLRA5 SLRA4 SLRA3 SLRA2 SLRA1 SLRA0 1111 1111 1111 1111
1F3Ch INLVLA INLVLA7 INLVLA6 INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0 1111 1111 1111 1111
1F3Dh IOCAP IOCAP7 IOCAP6 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 0000 0000 0000 0000
1F3Eh IOCAN IOCAN7 IOCAN6 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 0000 0000 0000 0000
1F3Fh IOCAF IOCAF7 IOCAF6 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 0000 0000 0000 0000
1F40h
— — Unimplemented — —
1F42h
1F43h ANSELB ANSB7 ANSB6 ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 1111 1111 1111 1111

PIC16(L)F15356/75/76/85/86
1F44h WPUB WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0 0000 0000 0000 0000
1F45h ODCONB ODCB7 ODCB6 ODCB5 ODCB4 ODCB3 ODCB2 ODCB1 ODCB0 0000 0000 0000 0000
1F46h SLRCONB SLRB7 SLRB6 SLRB5 SLRB4 SLRB3 SLRB2 SLRB1 SLRB0 1111 1111 1111 1111
1F47h INLVLB INLVLB7 INLVLB6 INLVLB5 INLVLB4 INLVLB3 INLVLB2 INLVLB1 INLVLB0 1111 1111 1111 1111
1F48h IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 0000 0000 0000 0000
1F49h IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 0000 0000 0000 0000
1F4Ah IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 0000 0000 0000 0000
1F4Bh
— — Unimplemented — —
1F4Dh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 90
TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 62 (Continued)
1F4Eh ANSELC ANSC7 ANSC6 ANSC5 ANSC4 ANSC3 ANSC2 ANSC1 ANSC0 1111 1111 1111 1111
1F4Fh WPUC WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0 0000 0000 0000 0000
1F50h ODCONC ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0 0000 0000 0000 0000
1F51h SLRCONC SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0 1111 1111 1111 1111
1F52h INLVLC INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 1111 1111 1111 1111
1F53h IOCCP IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0 0000 0000 0000 0000
1F54h IOCCN IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0 0000 0000 0000 0000
1F55h IOCCF IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0 0000 0000 0000 0000
1F56h
— — Unimplemented — —
1F58h
1F59h ANSELD(1) ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 1111 1111 1111 1111
WPUD(1)

PIC16(L)F15356/75/76/85/86
1F5Ah WPUD7 WPUD6 WPUD5 WPUD4 WPUD3 WPUD2 WPUD1 WPUD0 0000 0000 0000 0000
1F5Bh ODCOND(1) ODCD7 ODCD6 ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0 0000 0000 0000 0000
1F5Ch SLRCOND(1) SLRD7 SLRD6 SLRD5 SLRD4 SLRD3 SLRD2 SLRD1 SLRD0 1111 1111 1111 1111
1F5Dh INLVLD(1) INLVLD7 INLVLD6 INLVLD5 INLVLD4 INLVLD3 INLVLD2 INLVLD1 INLVLD0 1111 1111 1111 1111
1F5Eh
— — Unimplemented — —
1F63h
(1)
1F64h ANSELE — — — — — ANSE2 ANSE1 ANSE0 ---- -111 ---- -uuu
1F65h WPUE — — — — WPUE3 WPUE2(1) WPUE1(1) WPUE0(1) ---- 0000 ---- uuuu
1F66h ODCONE(1) — — — — — ODCE2 ODCE1 ODCE0 ---- -000 ---- -000
1F67h SLRCONE(1) — — — — — SLRE2 SLRE1 SLRE0 ---- -111 ---- -111
1F68h INLVLE — — — — INLVLE3 INLVLE2(1) INLVLE1(1) INLVLE0(1) ---- 1111 ---- uuuu
1F69h IOCEP — — — — IOCEP3 IOCEP2(1) IOCEP1(1) IOCEP0(1) ---- 0000 ---- 0000
1F6Ah IOCEN — — — — IOCEN3 IOCEN2(1) IOCEN1(1) IOCEN0(1) ---- 0000 ---- 0000
1F6Bh IOCEF — — — — IOCEF3 IOCEF2(1) IOCEF1(1) IOCEF0(1) ---- 0000 ---- 0000
1F6Ch
— — Unimplemented — —
1F6Fh
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 91

Note 1: Present only on PIC16(L)F15375/76/85/86.


TABLE 4-11: SPECIAL FUNCTION REGISTER SUMMARY BANKS 0-63 (CONTINUED)
 2016-2018 Microchip Technology Inc.

Value on: Value on:


Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
POR, BOR MCLR

Bank 63

CPU CORE REGISTERS; see Table 4-3 for specifics

1F8Ch
— — Unimplemented — —
1FE3h
1FE4h STATUS_SHAD — — — — — Z DC C ---- -xxx ---- -uuu
1FE5h WREG_SHAD Working Register Shadow xxxx xxxx uuuu uuuu
1FE6h BSR_SHAD — — — Bank Select Register Shadow ---x xxxx ---u uuuu
1FE7h PCLATH_SHAD — Program Counter Latch High Register Shadow -xxx xxxx uuuu uuuu
1FE8h FSR0L_SHAD Indirect Data Memory Address 0 Low Pointer Shadow xxxx xxxx uuuu uuuu
1FE9h FSR0H_SHAD Indirect Data Memory Address 0 High Pointer Shadow xxxx xxxx uuuu uuuu
1FEAh FSR1L_SHAD Indirect Data Memory Address 1 Low Pointer Shadow xxxx xxxx uuuu uuuu

PIC16(L)F15356/75/76/85/86
1FEBh FSR1H_SHAD Indirect Data Memory Address 1 High Pointer Shadow xxxx xxxx uuuu uuuu
1FECh — Unimplemented — —
1FEDh STKPTR — — — Current Stack Pointer ---1 1111 ---1 1111
1FEEh TOSL Top of Stack Low byte xxxx xxxx uuuu uuuu
1FEFh TOSH — Top of Stack High byte -xxx xxxx -uuu uuuu
Legend: x = unknown, u = unchanged, q = depends on condition, - = unimplemented, read as ‘0’, r = reserved. Shaded locations unimplemented, read as ‘0’.
DS40001866B-page 92
PIC16(L)F15356/75/76/85/86
4.4 PCL and PCLATH 4.4.2 COMPUTED GOTO
The Program Counter (PC) is 15 bits wide. The low byte A computed GOTO is accomplished by adding an offset to
comes from the PCL register, which is a readable and the program counter (ADDWF PCL). When performing a
writable register. The high byte (PC<14:8>) is not directly table read using a computed GOTO method, care should
readable or writable and comes from PCLATH. On any be exercised if the table location crosses a PCL memory
Reset, the PC is cleared. Figure 4-4 shows the five boundary (each 256-byte block). Refer to Application
situations for the loading of the PC. Note AN556, “Implementing a Table Read” (DS00556).

4.4.3 COMPUTED FUNCTION CALLS


FIGURE 4-4: LOADING OF PC IN
DIFFERENT SITUATIONS A computed function CALL allows programs to maintain
tables of functions and provide another way to execute
state machines or look-up tables. When performing a
Rev. 10-000042A
7/30/2013

table read using a computed function CALL, care


14 PCH PCL 0
PC
Instruction should be exercised if the table location crosses a PCL
with PCL as
Destination
memory boundary (each 256-byte block).
7 8
6 0 If using the CALL instruction, the PCH<2:0> and PCL
PCLATH ALU result
registers are loaded with the operand of the CALL
instruction. PCH<6:3> is loaded with PCLATH<6:3>.
14 PCH PCL 0 GOTO, The CALLW instruction enables computed calls by
PC
CALL combining PCLATH and W to form the destination
4 11 address. A computed CALLW is accomplished by
6 0
PCLATH OPCODE <10:0> loading the W register with the desired address and
executing CALLW. The PCL register is loaded with the
value of W and PCH is loaded with PCLATH.
14 PCH PCL 0
PC CALLW
4.4.4 BRANCHING
6
7
0 8 The branching instructions add an offset to the PC.
PCLATH W This allows relocatable code and code that crosses
page boundaries. There are two forms of branching,
14 PCH PCL 0
BRW and BRA. The PC will have incremented to fetch
PC BRW the next instruction in both cases. When using either
branching instruction, a PCL memory boundary may be
15
crossed.
PC + W
If using BRW, load the W register with the desired
14 PCH PCL 0
PC BRA unsigned address and execute BRW. The entire PC will
be loaded with the address PC + 1 + W.
15
If using BRA, the entire PC will be loaded with
PC + OPCODE <8:0>
PC + 1 + the signed value of the operand of the BRA
instruction.
4.4.1 MODIFYING PCL
Executing any instruction with the PCL register as the
destination simultaneously causes the Program
Counter PC<14:8> bits (PCH) to be replaced by the
contents of the PCLATH register. This allows the entire
contents of the program counter to be changed by writ-
ing the desired upper seven bits to the PCLATH regis-
ter. When the lower eight bits are written to the PCL
register, all 15 bits of the program counter will change
to the values contained in the PCLATH register and
those being written to the PCL register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 93


PIC16(L)F15356/75/76/85/86
4.5 Stack 4.5.1 ACCESSING THE STACK
All devices have a 16-level x 15-bit wide hardware The stack is accessible through the TOSH, TOSL and
stack (refer to Figure 4-5 through Figure 4-8). The STKPTR registers. STKPTR is the current value of the
stack space is not part of either program or data space. Stack Pointer. TOSH:TOSL register pair points to the
The PC is PUSHed onto the stack when CALL or TOP of the stack. Both registers are read/writable. TOS
CALLW instructions are executed or an interrupt causes is split into TOSH and TOSL due to the 15-bit size of the
a branch. The stack is POPed in the event of a PC. To access the stack, adjust the value of STKPTR,
RETURN, RETLW or a RETFIE instruction execution. which will position TOSH:TOSL, then read/write to
PCLATH is not affected by a PUSH or POP operation. TOSH:TOSL. STKPTR is five bits to allow detection of
overflow and underflow.
The stack operates as a circular buffer if the STVREN
bit is programmed to ‘0‘ (Configuration Words). This Note: Care should be taken when modifying the
means that after the stack has been PUSHed sixteen STKPTR while interrupts are enabled.
times, the seventeenth PUSH overwrites the value that
During normal program operation, CALL, CALLW and
was stored from the first PUSH. The eighteenth PUSH
interrupts will increment STKPTR while RETLW,
overwrites the second PUSH (and so on). The
RETURN, and RETFIE will decrement STKPTR.
STKOVF and STKUNF flag bits will be set on an
STKPTR can be monitored to obtain to value of stack
Overflow/Underflow, regardless of whether the Reset is
memory left at any given time. The STKPTR always
enabled.
points at the currently used place on the stack.
Note 1: There are no instructions/mnemonics Therefore, a CALL or CALLW will increment the
called PUSH or POP. These are actions STKPTR and then write the PC, and a return will
that occur from the execution of the unload the PC value from the stack and then
CALL, CALLW, RETURN, RETLW and decrement the STKPTR.
RETFIE instructions or the vectoring to Reference Figure 4-5 through Figure 4-8 for examples
an interrupt address. of accessing the stack.

FIGURE 4-5: ACCESSING THE STACK EXAMPLE 1

Rev. 10-000043A
7/30/2013

Stack Reset Disabled


TOSH:TOSL 0x0F STKPTR = 0x1F
(STVREN = 0)
0x0E
0x0D
0x0C
0x0B
Initial Stack Configuration:
0x0A
0x09 After Reset, the stack is empty. The
empty stack is initialized so the Stack
0x08 Pointer is pointing at 0x1F. If the Stack
0x07 Overflow/Underflow Reset is enabled, the
TOSH/TOSL register will return ‘0’. If the
0x06 Stack Overflow/Underflow Reset is
0x05 disabled, the TOSH/TOSL register will
return the contents of stack address
0x04 0x0F.
0x03
0x02
0x01
0x00
Stack Reset Enabled
TOSH:TOSL 0x1F 0x0000 STKPTR = 0x1F
(STVREN = 1)

 2016-2018 Microchip Technology Inc. DS40001866B-page 94


PIC16(L)F15356/75/76/85/86
FIGURE 4-6: ACCESSING THE STACK EXAMPLE 2
Rev. 10-000043B
7/30/2013

0x0F
0x0E
0x0D
0x0C
0x0B
0x0A
0x09 This figure shows the stack configuration
after the first CALL or a single interrupt.
0x08 If a RETURN instruction is executed, the
0x07 return address will be placed in the
Program Counter and the Stack Pointer
0x06 decremented to the empty state (0x1F).
0x05
0x04
0x03
0x02
0x01
TOSH:TOSL 0x00 Return Address STKPTR = 0x00

FIGURE 4-7: ACCESSING THE STACK EXAMPLE 3

Rev. 10-000043C
7/30/2013

0x0F
0x0E
0x0D
0x0C
After seven CALLs or six CALLs and an
0x0B interrupt, the stack looks like the figure on
the left. A series of RETURN instructions will
0x0A
repeatedly place the return addresses into
0x09 the Program Counter and pop the stack.
0x08
0x07
TOSH:TOSL 0x06 Return Address STKPTR = 0x06

0x05 Return Address


0x04 Return Address
0x03 Return Address
0x02 Return Address
0x01 Return Address
0x00 Return Address

 2016-2018 Microchip Technology Inc. DS40001866B-page 95


PIC16(L)F15356/75/76/85/86
FIGURE 4-8: ACCESSING THE STACK EXAMPLE 4
Rev. 10-000043D
7/30/2013

0x0F Return Address


0x0E Return Address
0x0D Return Address
0x0C Return Address
0x0B Return Address
0x0A Return Address When the stack is full, the next CALL or
0x09 Return Address an interrupt will set the Stack Pointer to
0x10. This is identical to address 0x00 so
0x08 Return Address the stack will wrap and overwrite the
0x07 Return Address return address at 0x00. If the Stack
Overflow/Underflow Reset is enabled, a
0x06 Return Address Reset will occur and location 0x00 will
0x05 Return Address not be overwritten.

0x04 Return Address


0x03 Return Address
0x02 Return Address
0x01 Return Address
TOSH:TOSL 0x00 Return Address STKPTR = 0x10

4.5.2 OVERFLOW/UNDERFLOW RESET


If the STVREN bit in Configuration Words (Register 5-2)
is programmed to ‘1’, the device will be Reset if the
stack is PUSHed beyond the sixteenth level or POPed
beyond the first level, setting the appropriate bits
(STKOVF or STKUNF, respectively) in the PCON
register.

4.6 Indirect Addressing


The INDFn registers are not physical registers. Any
instruction that accesses an INDFn register actually
accesses the register at the address specified by the
File Select Registers (FSR). If the FSRn address
specifies one of the two INDFn registers, the read will
return ‘0’ and the write will not occur (though Status bits
may be affected). The FSRn register value is created
by the pair FSRnH and FSRnL.
The FSR registers form a 16-bit address that allows an
addressing space with 65536 locations. These locations
are divided into three memory regions:
• Traditional/Banked Data Memory
• Linear Data Memory
• Program Flash Memory

 2016-2018 Microchip Technology Inc. DS40001866B-page 96


PIC16(L)F15356/75/76/85/86

FIGURE 4-9: INDIRECT ADDRESSING PIC16(L)F15375/85

Rev. 10-000044C
9/16/2016

0x0000 0x0000

Traditional
Data Memory

0x1FFF
0x2000

Linear
Data Memory

0X2FEF
0X2FF0
Reserved
0x7FFF
FSR
0x8000 PC value = 0x0000
Address
Range

Program
Flash Memory

0x9FFF PC value = 0x1FFF

 2016-2018 Microchip Technology Inc. DS40001866B-page 97


PIC16(L)F15356/75/76/85/86

FIGURE 4-10: INDIRECT ADDRESSING PIC16(L)F15356/76/86


Rev. 10-000044D
9/16/2016

0x0000 0x0000

Traditional
Data Memory

0x1FFF
0x2000

Linear
Data Memory

0X2FEF
0X2FF0
Reserved
0x7FFF
FSR
0x8000 PC value = 0x0000
Address
Range

Program
Flash Memory

0xBFFF PC value = 0x3FFF

 2016-2018 Microchip Technology Inc. DS40001866B-page 98


PIC16(L)F15356/75/76/85/86
4.6.1 TRADITIONAL/BANKED DATA
MEMORY
The traditional or banked data memory is a region from
FSR address 0x000 to FSR address 0x1FFF. The
addresses correspond to the absolute addresses of all
SFR, GPR and common registers.

FIGURE 4-11: TRADITIONAL/BANKED DATA MEMORY MAP


Rev. 10-000056B
12/14/2016

Direct Addressing Indirect Addressing

From Opcode
5 BSR 0 6 0 7 FSRxH 0 7 FSRxL 0
0 0 0

Bank Select Location Select Bank Select Location Select

000000 000001 000010 111111


0x00

0x7F
Bank 0 Bank 1 Bank 2 Bank 63

 2016-2018 Microchip Technology Inc. DS40001866B-page 99


PIC16(L)F15356/75/76/85/86
4.6.2 LINEAR DATA MEMORY 4.6.3 PROGRAM FLASH MEMORY
The linear data memory is the region from FSR To make constant data access easier, the entire
address 0x2000 to FSR address 0X2FEF. This region Program Flash Memory is mapped to the upper half of
is a virtual region that points back to the 80-byte blocks the FSR address space. When the MSB of FSRnH is
of GPR memory in all the banks. Refer to Figure 4-12 set, the lower 15 bits are the address in program
for the Linear Data Memory Map. memory which will be accessed through INDF. Only the
lower eight bits of each memory location is accessible
Note: The address range 0x2000 to 0x2FF0 rep-
via INDF. Writing to the Program Flash Memory cannot
resents the complete addressable Linear
be accomplished via the FSR/INDF interface. All
Data Memory up to Bank 50. The actual
instructions that access Program Flash Memory via the
implemented Linear Data Memory will dif-
FSR/INDF interface will require one additional
fer from one device to the other in a family.
instruction cycle to complete.
Confirm the memory limits on every
device.
FIGURE 4-13: PROGRAM FLASH
Unimplemented memory reads as 0x00. Use of the MEMORY MAP
linear data memory region allows buffers to be larger
than 80 bytes because incrementing the FSR beyond Rev. 10-000058A
7/31/2013

one bank will go directly to the GPR memory of the next


bank. 7 FSRnH 0 7 FSRnL 0
1
The 16 bytes of common memory are not included in
Location Select
the linear data memory region. 0x8000
0x0000

FIGURE 4-12: LINEAR DATA MEMORY


MAP
Rev. 10-000057B
8/24/2016
Program
Flash
Memory
(low 8 bits)
7 FSRnH 0 7 FSRnL 0

Location Select
0x2000
0x020
Bank 0
0x06F
0x7FFF
0x0A0 0xFFFF
Bank 1
0x0EF
0x120
Bank 2
0x16F

0x1920
Bank 50
0x196F
0x2FEF

 2016-2018 Microchip Technology Inc. DS40001866B-page 100


PIC16(L)F15356/75/76/85/86
5.0 DEVICE CONFIGURATION
Device configuration consists of the Configuration
Words, User ID, Device ID, Device Information Area
(DIA), (see Section 6.0 “Device Information Area”),
and the Device Configuration Information (DCI)
regions, (see Section 7.0 “Device Configuration
Information”).

5.1 Configuration Words


The devices have several Configuration Words
starting at address 8007h. The Configuration bits
establish configuration values prior to the execution of
any software; Configuration bits enable or disable
device-specific features.
In terms of programming, these important
Configuration bits should be considered:
1. LVP: Low-Voltage Programming Enable bit
• 1 = ON – Low-Voltage Programming is enabled.
MCLR/VPP pin function is MCLR. MCLRE
Configuration bit is ignored.
• 0 = OFF – HV on MCLR/VPP must be used for
programming.
2. CP: User Nonvolatile Memory (NVM)
Program Memory Code Protection bit
• 1 = OFF – User NVM code protection disabled
• 0 = ON – User NVM code protection enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 101


PIC16(L)F15356/75/76/85/86
5.2 Register Definitions: Configuration Words

REGISTER 5-1: CONFIGURATION WORD 1: OSCILLATORS


R/P-1 U-1 R/P-1 U-1 U-1 R/P-1
FCMEN — CSWEN — — CLKOUTEN
bit 13 bit 8

U-1 R/P-1 R/P-1 R/P-1 U-1 R/P-1 R/P-1 R/P-1


— RSTOSC2 RSTOSC1 RSTOSC0 — FEXTOSC2 FEXTOSC1 FEXTOSC0
bit 7 bit 0

Legend:
R = Readable bit P = Programmable bit x = Bit is unknown U = Unimplemented bit, read as
‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set W = Writable bit n = Value when blank or after Bulk
Erase

bit 13 FCMEN: Fail-Safe Clock Monitor Enable bit


1 = FSCM timer enabled
0 = FSCM timer disabled
bit 12 Unimplemented: Read as ‘1’
bit 11 CSWEN: Clock Switch Enable bit
1 = Writing to NOSC and NDIV is allowed
0 = The NOSC and NDIV bits cannot be changed by user software
bit 10-9 Unimplemented: Read as ‘1’
bit 8 CLKOUTEN: Clock Out Enable bit
If FEXTOSC = EC (high, mid or low) or Not Enabled:
1 = CLKOUT function is disabled; I/O or oscillator function on OSC2
0 = CLKOUT function is enabled; FOSC/4 clock appears at OSC2
Otherwise:
This bit is ignored.
bit 7 Unimplemented: Read as ‘1’
bit 6-4 RSTOSC<2:0>: Power-up Default Value for COSC bits
This value is the Reset-default value for COSC and selects the oscillator first used by user software.
111 = EXTOSC operating per FEXTOSC bits
110 = HFINTOSC (1 MHz) with OSCFRQ = '010' (4 MHz) and CDIV = '0010' (4:1)
101 = LFINTOSC
100 = SOSC
011 = Reserved
010 = EXTOSC with 4x PLL, with EXTOSC operating per FEXTOSC bits
001 = HFINTOSC with 2x PLL (32 MHz), with OSCFRQ = '101' (16 MHz) and CDIV = '0000' (1:1)
000 = HFINTOSC (32 MHz), with OSCFRQ = '110' (32 MHz) and CDIV = '0000' (1:1)
bit 3 Unimplemented: Read as ‘1’
bit 2-0 FEXTOSC<2:0>:FEXTOSC External Oscillator Mode Selection bits
111 = EC (External Clock) above 8 MHz
110 = EC (External Clock) for 100 kHz to 8 MHz
101 = EC (External Clock) below 100 kHz
100 = Oscillator not enabled
011 = Reserved (do not use)
010 = HS (Crystal oscillator) above 4 MHz
001 = XT (Crystal oscillator) above 100 kHz, below 4 MHz
000 = LP (Crystal oscillator) optimized for 32.768 kHz

 2016-2018 Microchip Technology Inc. DS40001866B-page 102


PIC16(L)F15356/75/76/85/86
REGISTER 5-2: CONFIGURATION WORD 2: SUPERVISORS
R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 U-1
DEBUG STVREN PPS1WAY ZCDDIS BORV —
bit 13 bit 8

R/P-1 R/P-1 R/P-1 U-1 U-1 U-1 R/P-1 R/P-1


BOREN1 BOREN0 LPBOREN — — — PWRTE MCLRE
bit 7 bit 0

Legend:
R = Readable bit P = Programmable bit x = Bit is unknown U = Unimplemented bit, read as
‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set W = Writable bit n = Value when blank or after Bulk
Erase
bit 13 DEBUG: Debugger Enable bit
1 = Background debugger disabled
0 = Background debugger enabled
bit 12 STVREN: Stack Overflow/Underflow Reset Enable bit
1 = Stack Overflow or Underflow will cause a Reset
0 = Stack Overflow or Underflow will not cause a Reset
bit 11 PPS1WAY: PPSLOCK One-Way Set Enable bit
1 = The PPSLOCK bit can be cleared and set only once; PPS registers remain locked after one clear/set cycle
0 = The PPSLOCK bit can be set and cleared repeatedly (subject to the unlock sequence)
bit 10 ZCDDIS: Zero-Cross Detect Disable bit
1 = ZCD disabled. ZCD can be enabled by setting the ZCDSEN bit of the ZCDCON register
0 = ZCD always enabled (ZCDSEN bit is ignored)
bit 9 BORV: Brown-out Reset Voltage Selection bit(1)
1 = Brown-out Reset voltage (VBOR) set to lower trip point level
0 = Brown-out Reset voltage (VBOR) set to higher trip point level
bit 8 Unimplemented: Read as ‘1’
bit 7-6 BOREN<1:0>: Brown-out Reset Enable bits
When enabled, Brown-out Reset Voltage (VBOR) is set by the BORV bit
11 = Brown-out Reset is enabled; SBOREN bit is ignored
10 = Brown-out Reset is enabled while running, disabled in Sleep; SBOREN bit is ignored
01 = Brown-out Reset is enabled according to SBOREN
00 = Brown-out Reset is disabled
bit 5 LPBOREN: Low-Power BOR Enable bit
1 = ULPBOR is disabled
0 = ULPBOR is enabled
bit 4-2 Unimplemented: Read as ‘1’
bit 1 PWRTE: Power-up Timer Enable bit
1 = PWRT is disabled
0 = PWRT is enabled
bit 0 MCLRE: Master Clear (MCLR) Enable bit
If LVP = 1:
RE3 pin function is MCLR (it will reset the device when driven low)
If LVP = 0:
1 = MCLR pin is MCLR (it will reset the device when driven low)
0 = MCLR pin may be used as general purpose RE3 input
Note 1: See Vbor parameter for specific trip point voltages.
2: The DEBUG bit in Configuration Words is managed automatically by device development tools including debuggers
and programmers. For normal device operation, this bit should be maintained as a ‘1’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 103


PIC16(L)F15356/75/76/85/86

REGISTER 5-3: CONFIGURATION WORD 3: WINDOWED WATCHDOG


R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1
WDTCCS2 WDTCCS1 WDTCCS0 WDTCWS2 WDTCWS1 WDTCWS0
bit 13 bit 8

U-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1


— WDTE1 WDTE0 WDTCPS4 WDTCPS3 WDTCPS2 WDTCPS1 WDTCPS0
bit 7 bit 0

Legend:
R = Readable bit P = Programmable bit x = Bit is unknown U = Unimplemented bit, read as ‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set W = Writable bit n = Value when blank or after Bulk
Erase

bit 13-11 WDTCCS<2:0>: WDT Input Clock Selector bits


111 = Software Control
110 = Reserved
.
.
.
.
010 = SOSC 32 kHz
001 = WDT reference clock is the 31.25 kHz HFINTOSC (MFINTOSC) output
000 = WDT reference clock is the 31.0 kHz LFINTOSC
bit 10-8 WDTCWS<2:0>: WDT Window Select bits

WDTWS at POR
Software Keyed
WDTCWS Window control of access
Window delay
Value opening WDTWS? required?
Percent of time
Percent of time
111 111 n/a 100 Yes No
110 111 n/a 100
101 101 25 75
100 100 37.5 62.5
011 011 50 50 No Yes
010 010 62.5 37.5
001 001 75 25
000 000 87.5 12.5

bit 7 Unimplemented: Read as ‘1’


bit 6-5 WDTE<1:0>: WDT Operating mode:
11 =WDT enabled regardless of Sleep; SWDTEN is ignored
10 =WDT enabled while Sleep = 0, suspended when Sleep = 1; SWDTEN ignored
01 =WDT enabled/disabled by SWDTEN bit in WDTCON0
00 =WDT disabled, SWDTEN is ignored

 2016-2018 Microchip Technology Inc. DS40001866B-page 104


PIC16(L)F15356/75/76/85/86
REGISTER 5-3: CONFIGURATION WORD 3: WINDOWED WATCHDOG (CONTINUED)
bit 4-0 WDTCPS<4:0>: WDT Period Select bits

WDTPS at POR
Software Control
WDTCPS Typical Time Out
Value Divider Ratio of WDTPS?
(FIN = 31 kHz)
11111(1) 01011 1:65536 216 2s Yes
11110 11110
... ... 1:32 25 1 ms No
10011 10011
10010 10010 1:8388608 223 256 s
10001 10001 1:4194304 222 128 s
10000 10000 1:2097152 221 64 s
01111 01111 1:1048576 220 32 s
01110 01110 1:524299 219 16 s
01101 01101 1:262144 218 8s
01100 01100 1:131072 217 4s
01011 01011 1:65536 216 2s
01010 01010 1:32768 215 1s
01001 01001 1:16384 214 512 ms No
01000 01000 1:8192 213 256 ms
00111 00111 1:4096 212 128 ms
00110 00110 1:2048 211 64 ms
00101 00101 1:1024 210 32 ms
00100 00100 1:512 29 16 ms
00011 00011 1:256 28 8 ms
00010 00010 1:128 27 4 ms
00001 00001 1:64 26 2 ms
00000 00000 1:32 25 1 ms

Note 1: 0b11111 is the default value of the WDTCPS bits.

 2016-2018 Microchip Technology Inc. DS40001866B-page 105


PIC16(L)F15356/75/76/85/86
REGISTER 5-4: CONFIGURATION WORD 4: MEMORY
R/W-1 U-1 R/W-1 U-1 R/W-1 R/W-1
LVP — WRTSAF(1) — WRTC(1) WRTB(1)
bit 13 12 11 10 9 bit 8

R/W-1 U-1 U-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1


WRTAPP(1) — — SAFEN(1) BBEN(1) BBSIZE2 BBSIZE1 BBSIZE0
bit 7 6 5 4 3 2 1 bit 0

Legend:
R = Readable bit P = Programmable bit x = Bit is unknown U = Unimplemented bit, read
as ‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set W = Writable bit n = Value when blank or after
Bulk Erase

bit 13 LVP: Low Voltage Programming Enable bit


1 = Low voltage programming enabled. MCLR/VPP pin function is MCLR. MCLRE Configuration bit is ignored.
0 = HV on MCLR/VPP must be used for programming.
The LVP bit cannot be written (to zero) while operating from the LVP programming interface. The purpose of this
rule is to prevent the user from dropping out of LVP mode while programming from LVP mode, or accidentally
eliminating LVP mode from the configuration state.
The preconditioned (erased) state for this bit is critical.
bit 12 Unimplemented: Read as ‘1’
bit 11 WRTSAF: Storage Area Flash Write Protection bit
1 = SAF NOT write-protected
0 = SAF write-protected
Unimplemented, if SAF is not supported in the device family and only applicable if SAFEN = 0.
bit 10 Unimplemented: Read as ‘1’
bit 9 WRTC: Configuration Register Write Protection bit
1 = Configuration Register NOT write-protected
0 = Configuration Register write-protected
bit 8 WRTB: Boot Block Write Protection bit
1 = Boot Block NOT write-protected
0 = Boot Block write-protected
Only applicable if BBEN = 0.
bit 7 WRTAPP: Application Block Write Protection bit
1 = Application Block NOT write-protected
0 = Application Block write-protected
bit 6-5 Unimplemented: Read as ‘1’
bit 4 SAFEN: SAF Enable bit
1 = SAF disabled
0 = SAF enabled
bit 3 BBEN: Boot Block Enable bit
1 = Boot Block disabled
0 = Boot Block enabled
bit 2-0 BBSIZE<2:0>: Boot Block Size Selection bits (See Table 5-1)
BBSIZE is used only when BBEN = 0
BBSIZ bits can only be written while BBEN = 1; after BBEN = 0, BBSIZ is write-protected.

Note 1: Bits are implemented as sticky bits. Once protection is enabled, it can only be reset through a Bulk Erase.

 2016-2018 Microchip Technology Inc. DS40001866B-page 106


PIC16(L)F15356/75/76/85/86
TABLE 5-1: BOOT BLOCK SIZE BITS
Actual Boot Block Size
User Program Memory Size (words) Last Boot Block
BBEN BBSIZE<2:0>
Memory Access
PIC16(L)F15375/85 PIC16(L)F15356/76/86
1 xxx 0 0 —
0 111 512 512 01FFh
0 110 1024 1024 03FFh
0 101 2048 2048 07FFh
0 100 4096 4096 0FFFh
0 011 — 8192 1FFFh
Note 1: The maximum boot block size is half the user program memory size. All selections higher than the maxi-
mum are set to half size. For example, all BBSIZE = 000 - 100 produce a boot block size of 4kW on a 8kW
device.

 2016-2018 Microchip Technology Inc. DS40001866B-page 107


PIC16(L)F15356/75/76/85/86

REGISTER 5-5: CONFIGURATION WORD 5: CODE PROTECTION


U-1 U-1 U-1 U-1 U-1 U-1
— — — — — —
bit 13 bit 8

U-1 U-1 U-1 U-1 U-1 U-1 U-1 R/P-1


— — — — — — — CP
bit 7 bit 0

Legend:
R = Readable bit P = Programmable bit x = Bit is unknown U = Unimplemented bit, read as ‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set W = Writable bit n = Value when blank or after Bulk
Erase

bit 13-1 Unimplemented: Read as ‘1’


bit 0 CP: Program Flash Memory Code Protection bit
1 = Program Flash Memory code protection disabled
0 = Program Flash Memory code protection enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 108


PIC16(L)F15356/75/76/85/86
5.3 Code Protection
Code protection allows the device to be protected from
unauthorized access. Program memory protection and
data memory are controlled independently. Internal
access to the program memory is unaffected by any
code protection setting.

5.3.1 PROGRAM MEMORY PROTECTION


The entire program memory space is protected from
external reads and writes by the CP bit in Configuration
Words. When CP = 0, external reads and writes of
program memory are inhibited and a read will return all
‘0’s. The CPU can continue to read program memory,
regardless of the protection bit settings. Self-writing the
program memory is dependent upon the write
protection setting. See Section 5.4 “Write
Protection” for more information.

5.4 Write Protection


Write protection allows the device to be protected from
unintended self-writes. Applications, such as boot
loader software, can be protected while allowing other
regions of the program memory to be modified.
The WRTAPP, WRTSAF, WRTB, WRTC bits in
Configuration Words (Register 5-4) define whether the
corresponding region of the program memory block is
protected or not.

5.5 User ID
Four memory locations (8000h-8003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
readable and writable during normal execution. See
Section 13.3.6 “NVMREG Access to Device
Information Area, Device Configuration Area, User
ID, Device ID and Configuration Words” for more
information on accessing these memory locations. For
more information on checksum calculation, see the
“PIC16(L)F153xx Memory Programming Specification”
(DS40001838).

 2016-2018 Microchip Technology Inc. DS40001866B-page 109


PIC16(L)F15356/75/76/85/86
5.6 Device ID and Revision ID
The 14-bit Device ID word is located at 8006h and the
14-bit Revision ID is located at 8005h. These locations
are read-only and cannot be erased or modified.
Development tools, such as device programmers and
debuggers, may be used to read the Device ID,
Revision ID and Configuration Words. These locations
can also be read from the NVMCON register.

5.7 Register Definitions: Device and Revision

REGISTER 5-6: DEVID: DEVICE ID REGISTER


R R R R R R
DEV<13:8>
bit 13 bit 8

R R R R R R R R
DEV<7:0>
bit 7 bit 0

Legend:
R = Readable bit
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 13-0 DEV<13:0>: Device ID bits

Device DEVID<13:0> Values


PIC16F15356 11 0000 1011 0000 (30B0h)
PIC16LF15356 11 0000 1011 0001 (30B1h)
PIC16F15375 11 0000 1011 0010 (30B2h)
PIC16LF15375 11 0000 1011 0011 (30B3h)
PIC16F15376 11 0000 1011 0100 (30B4h)
PIC16LF15376 11 0000 1011 0101 (30B5h)
PIC16F15385 11 0000 1011 0110 (30B6h)
PIC16LF15385 11 0000 1011 0111 (30B7h)
PIC16F15386 11 0000 1011 1000 (30B8h)
PIC16LF15386 11 0000 1011 1001 (30B9h)

 2016-2018 Microchip Technology Inc. DS40001866B-page 110


PIC16(L)F15356/75/76/85/86

REGISTER 5-7: REVISIONID: REVISION ID REGISTER


R R R R R R R R R R R R R R
1 0 MJRREV<5:0> MNRREV<5:0>
bit 13 bit 0

Legend:
R = Readable bit
‘0’ = Bit is cleared ‘1’ = Bit is set x = Bit is unknown

bit 13-12 Fixed Value: Read-only bits


These bits are fixed with value ‘10’ for all devices included in this data sheet.
bit 11-6 MJRREV<5:0>: Major Revision ID bits
These bits are used to identify a major revision.
bit 5-0 MNRREV<5:0>: Minor Revision ID bits
These bits are used to identify a minor revision.

 2016-2018 Microchip Technology Inc. DS40001866B-page 111


PIC16(L)F15356/75/76/85/86
6.0 DEVICE INFORMATION AREA The complete DIA table is shown in Table 6-1: Device
Information Area, followed by a description of each
The Device Information Area (DIA) is a dedicated region and its functionality. The data is mapped from
region in the program memory space; it is a new feature 8100h to 811Fh in the PIC16(L)F15356/75/76/85/86
in the PIC16(L)F15356/75/76/85/86 family of devices. family. These locations are read-only and cannot be
The DIA contains the calibration data for the internal erased or modified. The data is programmed into the
temperature indicator module, stores the Microchip device during manufacturing.
Unique Identifier words and the Fixed Voltage
Reference voltage readings measured in mV.

TABLE 6-1: DEVICE INFORMATION AREA


Address Range Name of Region Standard Device Information
MUI0
MUI1
MUI2
MUI3
8100h-8108h MUI4 Microchip Unique Identifier (9 Words)
MUI5
MUI6
MUI7
MUI8
8109h MUI9 1 Word Reserved
EUI0
EUI1
EUI2
EUI3
810Ah-8111h Unassigned (8 Words)
EUI4
EUI5
EUI6
EUI7
8112h Reserved Unassigned (1 word)
8113h TSLR2 Temperature indicator ADC reading at 90°C (low range setting)
8114h Reserved Unassigned (1 word)
8115h Reserved Unassigned (1 word)
8116h TSHR2 Temperature indicator ADC reading at 90°C (high range setting)
8117h Reserved Unassigned (1 Word)
8118h FVRA1X ADC FVR1 Output voltage for 1x setting (in mV)
8119h FVRA2X ADC FVR1 Output Voltage for 2x setting (in mV)
811Ah FVRA4X(1) ADC FVR1 Output Voltage for 4x setting (in mV)
811Bh FVRC1X Comparator FVR2 output voltage for 1x setting (in mV)
811Ch FVRC2X Comparator FVR2 output voltage for 2x setting (in mV)
811Dh FVRC4X(1) Comparator FVR2 output voltage for 4x setting (in mV)
811Eh-811Fh Unassigned (2 Words)
Note 1: Value not present on LF devices.

 2016-2018 Microchip Technology Inc. DS40001866B-page 112


PIC16(L)F15356/75/76/85/86
6.1 Microchip Unique identifier (MUI) 6.3 Analog-to-Digital Conversion Data
The PIC16(L)F15356/75/76/85/86 devices are individ-
of the Temperature Sensor
ually encoded during final manufacturing with a Micro- The purpose of the temperature indicator module is to
chip Unique Identifier, or MUI. The MUI cannot be provide a temperature-dependent voltage that can be
erased by a Bulk Erase command or any other user- measured by an analog module. Section 19.0 “Tem-
accessible means. This feature allows for manufactur- perature Indicator Module” explains the operation of
ing traceability of Microchip Technology devices in the Temperature Indicator module and defines terms
applications where this is a required. It may also be such as the low range and high range settings of the
used by the application manufacturer for a number of sensor.
functions that require unverified unique identification,
The DIA table contains the internal ADC measurement
such as:
values of the temperature sensor for low and high
• Tracking the device range at fixed points of reference. The values are
• Unique serial number measured during test and are unique to each device.
The MUI consists of nine program words. When taken The right-justified ADC readings are stored in the DIA
together, these fields form a unique identifier. The MUI memory region. The calibration data can be used to
is stored in nine read-only locations, located between plot the approximate sensor output voltage, VTSENSE
8100h to 8109h in the DIA space. Table 6-1 lists the vs. Temperature curve.
addresses of the identifier words. • TSLR2: Address 8113h stores the measurements
for the low range setting of the temperature
Note: For applications that require verified unique
sensor at VDD = 3V.
identification, contact your Microchip Tech-
• TSHR2: Address 8116h stores the measurements
nology sales office to create a Serialized
for the high range setting of the temperature
Quick Turn Programming option.
sensor at VDD = 3V.
The stored measurements are made by the device
6.2 External Unique Identifier (EUI) ADC using the internal VREF = 2.048V.
The EUI data is stored at locations 810Ah to 8111h in
the program memory region. This region is an optional 6.4 Fixed Voltage Reference Data
space for placing application specific information. The
data is coded per customer requirements during The Fixed Voltage Reference, or FVR, is a stable
manufacturing. The EUI cannot be erased by a Bulk voltage reference, independent of VDD, with 1.024V,
Erase command. 2.048V or 4.096V selectable output levels. The output
of the FVR can be configured to supply a reference
voltage to the following:
Note: Data is stored in this address range on • ADC input channel
receiving a request from the customer. • ADC positive reference
The customer may contact the local sales • Comparator positive input
representative or Field Applications • Digital-to-Analog Converter
Engineer, and provide them the unique
For more information on the FVR, refer to Section 18.0
identifier information that is required to be
“Fixed Voltage Reference (FVR)”.
stored in this region.
The DIA stores measured FVR voltages for this device
in mV for the different buffer settings of 1x, 2x or 4x at
program memory locations 8118h to 811Dh.
• FVRA1X stores the value of ADC FVR1 Output
voltage for 1x setting (in mV)
• FVRA2X stores the value of ADC FVR1 Output
Voltage for 2x setting (in mV)
• FVRA4X stores the value of ADC FVR1 Output
Voltage for 4x setting (in mV)
• FVRC1X stores the value of Comparator FVR2
output voltage for 1x setting (in mV)
• FVRC2X stores the value of Comparator FVR2
output voltage for 2x setting (in mV)
• FVRC4X stores the value of Comparator FVR2
output voltage for 4x setting (in mV)

 2016-2018 Microchip Technology Inc. DS40001866B-page 113


PIC16(L)F15356/75/76/85/86
7.0 DEVICE CONFIGURATION Refer to Table 7-1 for the complete DCI table address
and description. The DCI holds information about the
INFORMATION
device which is useful for programming and bootloader
The Device Configuration Information (DCI) is a applications. These locations are read-only and cannot
dedicated region in the Program Flash Memory be erased or modified.
mapped from 8200h to 821Fh. The data stored in the
DCI memory is hard-coded into the device during
manufacturing.
TABLE 7-1: DEVICE CONFIGURATION INFORMATION FOR PIC16(L)F15356/75/76/85/86 DEVICES
VALUE
ADDRESS Name DESCRIPTION UNITS
PIC16(L)F15356/75/76/85/86
8200h ERSIZ Erase Row Size 32 Words
8201h WLSIZ Number of write latches 32 Latches
8202h URSIZ Number of User Rows See Table 7-2 Rows
8203h EESIZ EE Data memory size 0 Bytes
8204h PCNT Pin Count See Table 7-3 Pins

TABLE 7-2: MEMORY SIZE AND NUMBER OF USER ROWS


Part Name Memory size Number of user rows
PIC16(L)F15356 16K 512
PIC16(L)F15375/85 8K 256
PIC16(L)F15376/86 16K 512

TABLE 7-3: PIN COUNT


Part Number Pin Count
PIC16(L)F15356 28
PIC16(L)F15375/76 40/44
PIC16(L)F15385/86 48

7.1 DIA and DCI Access


The DIA and DCI data are read-only and cannot be
erased or modified. See 13.3.6 “NVMREG Access to
Device Information Area, Device Configuration
Area, User ID, Device ID and Configuration Words”
for more information on accessing these memory
locations.
Development tools, such as device programmers and
debuggers, may be used to read the DIA and DCI
regions, similar to the Device ID and Revision ID.

 2016-2018 Microchip Technology Inc. DS40001866B-page 114


PIC16(L)F15356/75/76/85/86
8.0 RESETS A simplified block diagram of the On-Chip Reset Circuit
is shown in Figure 8-1.
There are multiple ways to reset this device:
• Power-on Reset (POR)
• Brown-out Reset (BOR)
• Low-Power Brown-out Reset (LPBOR)
• MCLR Reset
• WWDT Reset
• RESET instruction
• Stack Overflow
• Stack Underflow
• Programming mode exit
• Memory Violation Reset (MEMV)
To allow VDD to stabilize, an optional Power-up Timer
can be enabled to extend the Reset time after a BOR
or POR event.

FIGURE 8-1: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT


Rev. 10-000006F
8/30/2016

ICSP™ Programming Mode Exit


RESET Instruction
Memory Violation

Stack Underflow
Stack Overflow

VPP/MCLR MCLRE

WWDT Time-out/
Window violation Device
Reset

Power-on
Reset
VDD

Brown-out
R
Reset(1) Power-up
Timer
LFINTOSC 
PWRTE
LPBOR
Reset

Note 1: See Table 8-1 for BOR active conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 115


PIC16(L)F15356/75/76/85/86
8.1 Power-on Reset (POR)
The POR circuit holds the device in Reset until VDD has
reached an acceptable level for minimum operation.
Slow rising VDD, fast operating speeds or analog
performance may require greater than minimum VDD.
The PWRT, BOR or MCLR features can be used to
extend the start-up period until all device operation
conditions have been met.

8.2 Brown-out Reset (BOR)


The BOR circuit holds the device in Reset when VDD
reaches a selectable minimum level. Between the
POR and BOR, complete voltage range coverage for
execution protection can be implemented.
The Brown-out Reset module has four operating
modes controlled by the BOREN<1:0> bits in
Configuration Words. The four operating modes are:
• BOR is always on
• BOR is off when in Sleep
• BOR is controlled by software
• BOR is always off
Refer to Table 8-1 for more information.
The Brown-out Reset voltage level is selectable by
configuring the BORV bit in Configuration Words.
A VDD noise rejection filter prevents the BOR from
triggering on small events. If VDD falls below VBOR for
a duration greater than parameter TBORDC, the device
will reset. See Figure 8-2 for more information.

TABLE 8-1: BOR OPERATING MODES


Instruction Execution upon:
BOREN<1:0> SBOREN Device Mode BOR Mode
Release of POR or Wake-up from Sleep

11 X X Active Wait for release of BOR(1) (BORRDY = 1)


Awake Active Waits for release of BOR (BORRDY = 1)
10 X
Sleep Disabled Waits for BOR Reset release

1 X Active Waits for BOR Reset release (BORRDY = 1)


01
0 X Disabled
Begins immediately (BORRDY = x)
00 X X Disabled
Note 1:In this specific case, “Release of POR” and “Wake-up from Sleep”, there is no delay in start-up. The BOR
ready flag, (BORRDY = 1), will be set before the CPU is ready to execute instructions because the BOR
circuit is forced on by the BOREN<1:0> bits.

8.2.1 BOR IS ALWAYS ON 8.2.2 BOR IS OFF IN SLEEP


When the BOREN bits of Configuration Words are When the BOREN bits of Configuration Words are
programmed to ‘11’, the BOR is always on. The device programmed to ‘10’, the BOR is on, except in Sleep.
start-up will be delayed until the BOR is ready and VDD The device start-up will be delayed until the BOR is
is higher than the BOR threshold. ready and VDD is higher than the BOR threshold.
BOR protection is active during Sleep. The BOR does BOR protection is not active during Sleep. The device
not delay wake-up from Sleep. wake-up will be delayed until the BOR is ready.

 2016-2018 Microchip Technology Inc. DS40001866B-page 116


PIC16(L)F15356/75/76/85/86
8.2.3 BOR CONTROLLED BY SOFTWARE 8.2.4 BOR IS ALWAYS OFF
When the BOREN bits of Configuration Words are When the BOREN bits of the Configuration Words are
programmed to ‘01’, the BOR is controlled by the programmed to ‘00’, the BOR is off at all times. The
SBOREN bit of the BORCON register. The device start- device start-up is not delayed by the BOR ready
up is not delayed by the BOR ready condition or the condition or the VDD level.
VDD level.
BOR protection begins as soon as the BOR circuit is
ready. The status of the BOR circuit is reflected in the
BORRDY bit of the BORCON register.
BOR protection is unchanged by Sleep.

FIGURE 8-2: BROWN-OUT SITUATIONS

VDD
VBOR

Internal
Reset TPWRT(1)

VDD
VBOR

Internal < TPWRT


Reset TPWRT(1)

VDD
VBOR

Internal
Reset TPWRT(1)

Note 1: TPWRT delay only if PWRTE bit is programmed to ‘0’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 117


PIC16(L)F15356/75/76/85/86
8.3 Register Definitions: Brown-out Reset Control
REGISTER 8-1: BORCON: BROWN-OUT RESET CONTROL REGISTER
R/W-1/u U-0 U-0 U-0 U-0 U-0 U-0 R-q/u
SBOREN(1) — — — — — — BORRDY
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 SBOREN: Software Brown-out Reset Enable bit(1)


If BOREN <1:0> in Configuration Words  01:
SBOREN is read/write, but has no effect on the BOR.
If BOREN <1:0> in Configuration Words = 01:
1 = BOR Enabled
0 = BOR Disabled
bit 6-1 Unimplemented: Read as ‘0’
bit 0 BORRDY: Brown-out Reset Circuit Ready Status bit
1 = The Brown-out Reset circuit is active
0 = The Brown-out Reset circuit is inactive

Note 1: BOREN<1:0> bits are located in Configuration Words.

 2016-2018 Microchip Technology Inc. DS40001866B-page 118


PIC16(L)F15356/75/76/85/86
8.4 Low-Power Brown-out Reset 8.5.2 MCLR DISABLED
(LPBOR) When MCLR is disabled, the pin functions as a general
purpose input and the internal weak pull-up is under
The Low-Power Brown-out Reset (LPBOR) is an
software control. See Section 14.1 “I/O Priorities” for
important part of the Reset subsystem. Refer to
more information.
Figure 8-1 to see how the BOR and LPBOR interact
with other modules.
8.6 Windowed Watchdog Timer
The LPBOR is used to monitor the external VDD pin.
When too low of a voltage is detected, the device is
(WWDT) Reset
held in Reset. The Watchdog Timer generates a Reset if the firmware
does not issue a CLRWDT instruction within the time-out
8.4.1 ENABLING LPBOR period and the window is open. The TO and PD bits in
The LPBOR is controlled by the LPBOR bit of the the STATUS register and the WDT bit in PCON are
Configuration Word (Register 5-1). When the device is changed to indicate a WDT Reset caused by the timer
erased, the LPBOR module defaults to disabled. overflowing, and WDTWV bit in the PCON register is
changed to indicate a WDT Reset caused by a window
8.4.2 LPBOR MODULE OUTPUT violation. See Section 12.0 “Windowed Watchdog
The output of the LPBOR module is a signal indicating Timer (WWDT)” for more information.
whether or not a Reset is to be asserted. When this
occurs, a register bit (BOR) is changed to indicate that 8.7 RESET Instruction
a BOR Reset has occurred. The same bit is set for
A RESET instruction will cause a device Reset. The RI
either the BOR or the LPBOR (refer to Register 8-3).
bit in the PCON register will be set to ‘0’. See Table 8-4
This signal is OR’d with the output of the BOR module
for default conditions after a RESET instruction has
to provide the generic BOR signal, which goes to the
occurred.
PCON register and to the power control block. Refer to
Figure 8-1 for the OR gate connections of the BOR and
LPBOR Reset signals, which eventually generates one 8.8 Stack Overflow/Underflow Reset
common BOR Reset. The device can reset when the Stack Overflows or
Underflows. The STKOVF or STKUNF bits of the PCON
8.5 MCLR register indicate the Reset condition. These Resets are
enabled by setting the STVREN bit in Configuration
The MCLR is an optional external input that can reset
Words. See Section 4.5.2 “Overflow/Underflow
the device. The MCLR function is controlled by the
Reset” for more information.
MCLRE bit of Configuration Words and the LVP bit of
Configuration Words (Table 8-2).
8.9 Programming Mode Exit
TABLE 8-2: MCLR CONFIGURATION Upon exit of In-Circuit Serial Programming™ (ICSP™)
mode, the device will behave as if a POR had just
MCLRE LVP MCLR occurred (the device does not reset upon run time self-
0 0 Disabled programming/erase operations).
1 0 Enabled
8.10 Power-up Timer
x 1 Enabled
The Power-up Timer optionally delays device execution
8.5.1 MCLR ENABLED after a BOR or POR event. This timer is typically used to
When MCLR is enabled and the pin is held low, the device allow VDD to stabilize before allowing the device to start
is held in Reset. The MCLR pin is connected to VDD running.
through an internal weak pull-up. Refer to Section 2.3 The Power-up Timer is controlled by the PWRTE bit of
“Master Clear (MCLR) Pin” for recommended MCLR the Configuration Words.
connections. The Power-up Timer provides a nominal 64 ms time out
The device has a noise filter in the MCLR Reset path. on POR or Brown-out Reset. The device is held in
The filter will detect and ignore small pulses. Reset as long as PWRT is active. The PWRT delay
allows additional time for the VDD to rise to an accept-
Note: A Reset does not drive the MCLR pin low.
able level. The Power-up Timer is enabled by clearing
the PWRTE bit in the Configuration Words. The Power-
up Timer starts after the release of the POR and BOR.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting” (DS00607).

 2016-2018 Microchip Technology Inc. DS40001866B-page 119


PIC16(L)F15356/75/76/85/86
8.11 Start-up Sequence
Upon the release of a POR or BOR, the following must
occur before the device will begin executing:
1. Power-up Timer runs to completion (if enabled).
2. Oscillator start-up timer runs to completion (if
required for oscillator source).
3. MCLR must be released (if enabled).
The total time-out will vary based on oscillator
configuration and Power-up Timer Configuration. See
Section 9.0 “Oscillator Module (with Fail-Safe
Clock Monitor)” for more information.
The Power-up Timer runs independently of MCLR
Reset. If MCLR is kept low long enough, the Power-up
Timer and oscillator start-up timer will expire. This is
useful for testing purposes or to synchronize more than
one device operating in parallel. See Figure 8-3.

FIGURE 8-3: RESET START-UP SEQUENCE


Rev. 10-000032C
9/14/2016

VDD
Internal POR
TPWRT
Power-up Timer
MCLR
Internal RESET
Int. Oscillator
FOSC
Begin Execution code execution (1) code execution (1)

Internal Oscillator, PWRTEN = 0 Internal Oscillator, PWRTEN = 1

VDD
Internal POR
TPWRT
Power-up Timer
MCLR
Internal RESET
Ext. Clock (EC)
FOSC
Begin Execution
code execution (1) code execution (1)
External Clock (EC modes), PWRTEN = 0 External Clock (EC modes), PWRTEN = 1

Note 1: Code execution begins 10 FOSC cycles after the FOSC clock is released.

 2016-2018 Microchip Technology Inc. DS40001866B-page 120


PIC16(L)F15356/75/76/85/86
8.12 Memory Execution Violation
A Memory Execution Violation Reset occurs if
executing an instruction being fetched from outside the
valid execution area. The different valid execution
areas are defined as follows:
• Flash Memory: Table 4-1 shows the addresses
available on the PIC16(L)F15356/75/76/85/86
devices based on user Flash size. Execution out-
side this region generates a memory execution
violation.
• Storage Area Flash (SAF): If Storage Area Flash
(SAF) is enabled (Section 4.2.3 “Storage Area
Flash”), the SAF area (Table 4-2) is not a valid
execution area.
Prefetched instructions that are not executed do not
cause memory execution violations. For example, a
GOTO instruction in the last memory location will prefetch
from an invalid location; this is not an error. If an
instruction from an invalid location tries to execute, the
memory violation is generated immediately, and any
concurrent interrupt requests are ignored. When a
memory execution violation is generated, the device is
reset and flag MEMV is cleared in PCON1 (Register 8-3)
to signal the cause. The flag needs to be set in code after
a memory execution violation.

 2016-2018 Microchip Technology Inc. DS40001866B-page 121


PIC16(L)F15356/75/76/85/86
8.13 Determining the Cause of a Reset
Upon any Reset, multiple bits in the STATUS and
PCON registers are updated to indicate the cause of
the Reset. Table 8-3 and Table 8-4 show the Reset
conditions of these registers.
TABLE 8-3: RESET STATUS BITS AND THEIR SIGNIFICANCE
STKUNF

RMCLR
STOVF

MEMV
RWDT

BOR
POR

PD
TO
Condition

RI
0 0 1 1 1 0 x 1 1 1 Power-on Reset
0 0 1 1 1 0 x 0 x u Illegal, TO is set on POR
0 0 1 1 1 0 x x 0 u Illegal, PD is set on POR
0 0 u 1 1 u 0 1 1 u Brown-out Reset
u u 0 u u u u 0 u u WWDT Reset
u u u u u u u 0 0 u WWDT Wake-up from Sleep
u u u u u u u 1 0 u Interrupt Wake-up from Sleep
u u u 0 u u u u u 1 MCLR Reset during normal operation
u u u 0 u u u 1 0 u MCLR Reset during Sleep
u u u u 0 u u u u u RESET Instruction Executed
1 u u u u u u u u u Stack Overflow Reset (STVREN = 1)
u 1 u u u u u u u u Stack Underflow Reset (STVREN = 1)
u u u u u u u u u 0 Memory violation Reset

TABLE 8-4: RESET CONDITION FOR SPECIAL REGISTERS


Program STATUS PCON0 PCON1
Condition
Counter Register Register Register
Power-on Reset 0000h ---1 1000 0011 110x ---- --1-
MCLR Reset during normal operation 0000h ---u uuuu uuuu 0uuu ---- --1-
MCLR Reset during Sleep 0000h ---1 0uuu uuuu 0uuu ---- --u-
WWDT Timeout Reset 0000h ---0 uuuu uuu0 uuuu ---- --u-
WWDT Wake-up from Sleep PC + 1 ---0 0uuu uuuu uuuu ---- --u-
WWDT Window Violation 0000h ---u uuuu uu0u uuuu ---- --u-
Brown-out Reset 0000h ---1 1000 0011 11u0 ---- --u-
(1)
Interrupt Wake-up from Sleep PC + 1 ---1 0uuu uuuu uuuu ---- --u-
RESET Instruction Executed 0000h ---u uuuu uuuu u0uu ---- --u-
Stack Overflow Reset (STVREN = 1) 0000h ---u uuuu 1uuu uuuu ---- --u-
Stack Underflow Reset (STVREN = 1) 0000h ---u uuuu u1uu uuuu ---- --u-
Memory Violation Reset (MEMV = 0) 0 -uuu uuuu uuuu uuuu ---- --0-
Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as ‘0’.
Note 1:When the wake-up is due to an interrupt and Global Enable bit (GIE) is set, the return address is pushed on
the stack and PC is loaded with the interrupt vector (0004h) after execution of PC + 1.

 2016-2018 Microchip Technology Inc. DS40001866B-page 122


PIC16(L)F15356/75/76/85/86
8.14 Power Control (PCONx) Registers
The Power Control (PCONx) registers contain flag bits
to differentiate between a:
• Power-on Reset (POR)
• Brown-out Reset (BOR)
• Reset Instruction Reset (RI)
• MCLR Reset (RMCLR)
• Watchdog Timer Reset (RWDT)
• Watchdog Timer Window Violation Reset
(WDTWV)
• Stack Underflow Reset (STKUNF)
• Stack Overflow Reset (STKOVF)
• Memory Violation Reset (MEMV)
The PCON0 register bits are shown in Register 8-2.
The PCON1 register bits are shown in Register 8-3.
Hardware will change the corresponding register bit
during the Reset process; if the Reset was not caused
by the condition, the bit remains unchanged (Table 8-4).
Software should reset the bit to the inactive state after
the restart (hardware will not reset the bit).
Software may also set any PCON bit to the active state,
so that user code may be tested, but no reset action will
be generated.

 2016-2018 Microchip Technology Inc. DS40001866B-page 123


PIC16(L)F15356/75/76/85/86
8.15 Register Definitions: Power Control

REGISTER 8-2: PCON0: POWER CONTROL REGISTER 0


R/W/HS-0/q R/W/HS-0/q R/W/HC-1/q R/W/HC-1/q R/W/HC-1/q R/W/HC-1/q R/W/HC-q/u R/W/HC-q/u
STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR
bit 7 bit 0

Legend:
HC = Bit is cleared by hardware HS = Bit is set by hardware
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -m/n = Value at POR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 STKOVF: Stack Overflow Flag bit


1 = A Stack Overflow occurred
0 = A Stack Overflow has not occurred or cleared by firmware
bit 6 STKUNF: Stack Underflow Flag bit
1 = A Stack Underflow occurred
0 = A Stack Underflow has not occurred or cleared by firmware
bit 5 WDTWV: WDT Window Violation Flag bit
1 = A WDT Window Violation Reset has not occurred or set to ‘1’ by firmware
0 = A WDT Window Violation Reset has occurred (a CLRWDT instruction was executed either without
arming the window or outside the window (cleared by hardware)
bit 4 RWDT: Watchdog Timer Reset Flag bit
1 = A Watchdog Timer Reset has not occurred or set to ‘1’ by firmware
0 = A Watchdog Timer Reset has occurred (cleared by hardware)
bit 3 RMCLR: MCLR Reset Flag bit
1 = A MCLR Reset has not occurred or set to ‘1’ by firmware
0 = A MCLR Reset has occurred (cleared by hardware)
bit 2 RI: RESET Instruction Flag bit
1 = A RESET instruction has not been executed or set to ‘1’ by firmware
0 = A RESET instruction has been executed (cleared by hardware)
bit 1 POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0 BOR: Brown-out Reset Status bit
1 = No Brown-out Reset occurred
0 = A Brown-out Reset occurred (must be set in software after a Power-on Reset or Brown-out Reset
occurs)

 2016-2018 Microchip Technology Inc. DS40001866B-page 124


PIC16(L)F15356/75/76/85/86

REGISTER 8-3: PCON1: POWER CONTROL REGISTER 0


U-0 U-0 U-0 U-0 U-0 U-0 R/W/HC-1/u U-0
— — — — — — MEMV —
bit 7 bit 0

Legend:
HC = Bit is cleared by hardware
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -m/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-2 Unimplemented: Read as ‘0’


bit 1 MEMV: Memory Violation Flag bit
1 = No Memory Violation Reset occurred or set to ‘1’ by firmware.
0 = A Memory Violation Reset occurred (set to ‘0’ in hardware when a Memory Violation occurs))
bit 0 Unimplemented: Read as ‘0’

TABLE 8-5: SUMMARY OF REGISTERS ASSOCIATED WITH RESETS


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
BORCON SBOREN — — — — — — BORRDY 118
PCON0 STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR 125
PCON1 — — — — — — MEMV — 125
STATUS — — — TO PD Z DC C 54
WDTCON0 — — WDTPS<4:0> SWDTEN 176
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Resets.

 2016-2018 Microchip Technology Inc. DS40001866B-page 125


PIC16(L)F15356/75/76/85/86
9.0 OSCILLATOR MODULE (WITH If an external clock source is selected, the FEXTOSC
bits of Configuration Word 1 must be used to select the
FAIL-SAFE CLOCK MONITOR)
external clock mode.

9.1 Overview The external oscillator module can be configured in one


of the following clock modes, by setting the
The oscillator module has a wide variety of clock FEXTOSC<2:0> bits of Configuration Word 1:
sources and selection features that allow it to be used 1. ECL – External Clock Low-Power mode
in a wide range of applications while maximizing ECL ≤ 500 kHz
performance and minimizing power consumption.
2. ECM – External Clock Medium Power mode
Figure 9-1 illustrates a block diagram of the oscillator
ECM ≤ 8 MHz
module.
3. ECH – External Clock High-Power mode
Clock sources can be supplied from external oscillators, ECH ≤ 32 MHz
quartz-crystal resonators. In addition, the system clock
4. LP – 32 kHz Low-Power Crystal mode.
source can be supplied from one of two internal
oscillators and PLL circuits, with a choice of speeds 5. XT – Medium Gain Crystal or Ceramic Resonator
selectable via software. Additional clock features Oscillator mode (between 100 kHz and 4 MHz)
include: 6. HS – High Gain Crystal or Ceramic Resonator
mode (above 4 MHz)
• Selectable system clock source between external
or internal sources via software. The ECH, ECM, and ECL clock modes rely on an
• Fail-Safe Clock Monitor (FSCM) designed to external logic level signal as the device clock source.
detect a failure of the external clock source (LP, The LP, XT, and HS clock modes require an external
XT, HS, ECH, ECM, ECL) and switch crystal or resonator to be connected to the device.
automatically to the internal oscillator. Each mode is optimized for a different frequency range.
The INTOSC internal oscillator block produces low and
• Oscillator Start-up Timer (OST) ensures stability
high-frequency clock sources, designated LFINTOSC
of crystal oscillator sources.
and HFINTOSC. (see Internal Oscillator Block,
The RSTOSC bits of Configuration Word 1 determine Figure 9-1). A wide selection of device clock
the type of oscillator that will be used when the device frequencies may be derived from these clock sources.
reset, including when it is first powered up.
The internal clock modes, LFINTOSC, HFINTOSC (set
at 1 MHz), or HFINTOSC (set at 32 MHz) can be set
through the RSTOSC bits.

 2016-2018 Microchip Technology Inc. DS40001866B-page 126


FIGURE 9-1: SIMPLIFIED PIC® MCU CLOCK SOURCE BLOCK DIAGRAM
 2016-2018 Microchip Technology Inc.

Rev. 10-000208J
12/13/2016

CLKIN

External
Oscillator
(EXTOSC)

CLKOUT
CDIV<4:0>
4x PLL Mode
COSC<2:0>
SOSCIN/SOSCI

Secondary PLLBlock 512


Oscillator 1001
256
(SOSC) 111 1000

PIC16(L)F15356/75/76/85/86
128 Sleep
001 0111

9-bit Postscaler Divider


2x PLL Mode System Clock
SOSCO
64
010 0110
LFINTOSC 32
100 0101
31kHz 16
101 0100 SYSCMD Peripheral Clock
Oscillator
8
110 0011
4
Reserved 000 0010 Sleep
2
011 0001 Idle
1
0000
HFINTOSC

HFFRQ<2:0>

1 – 32 MHz
MFINTOSC FSCM
Oscillator

To Peripherals
To Peripherals
DS40001866B-page 127

500 kHz
To Peripherals
31.25 kHz
To Peripherals
To Peripherals
PIC16(L)F15356/75/76/85/86
9.2 Clock Source Types The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
Clock sources can be classified as external or internal. operation after a Power-on Reset (POR) or wake-up
External clock sources rely on external circuitry for the from Sleep. Because the PIC® MCU design is fully
clock source to function. Examples are: oscillator static, stopping the external clock input will have the
modules (ECH, ECM, ECL mode), quartz crystal effect of halting the device while leaving all data intact.
resonators or ceramic resonators (LP, XT and HS Upon restarting the external clock, the device will
modes). resume operation as if no time had elapsed.
There is also a secondary oscillator block which is
optimized for a 32.768 kHz external clock source, FIGURE 9-2: EXTERNAL CLOCK (EC)
which can be used as an alternate clock source. MODE OPERATION
There are two internal oscillator blocks:
Clock from CLKIN
- HFINTOSC
Ext. System
- LFINTOSC PIC® MCU
The HFINTOSC can produce clock frequencies from 1-
32 MHz, and is responsible for generating the two OSC2/CLKOUT
FOSC/4 or I/O(1)
MFINTOSC frequencies (500 kHz and 32 kHz) that can
be used by some peripherals. The LFINTOSC
generates a 31 kHz clock frequency. Note 1: Output depends upon CLKOUTEN bit of the
Configuration Words.
There is a 4x PLL that can be used by the external
oscillator. See Section 9.2.1.4 “4x PLL” for more
details. Additionally, there is a PLL that can be used by 9.2.1.2 LP, XT, HS Modes
the HFINTOSC at certain frequencies. See The LP, XT and HS modes support the use of quartz
Section 9.2.2.2 “Internal Oscillator Frequency crystal resonators or ceramic resonators connected to
Adjustment” for more details. OSC1 and OSC2 (Figure 9-3). The three modes select
a low, medium or high gain setting of the internal
9.2.1 EXTERNAL CLOCK SOURCES inverter-amplifier to support various resonator types
An external clock source can be used as the device and speed.
system clock by performing one of the following LP Oscillator mode selects the lowest gain setting of the
actions: internal inverter-amplifier. LP mode current consumption
• Program the RSTOSC<2:0> bits in the is the least of the three modes. This mode is designed to
Configuration Words to select an external clock drive only 32.768 kHz tuning-fork type crystals (watch
source that will be used as the default system crystals), but can operate up to 100 kHz.
clock upon a device Reset XT Oscillator mode selects the intermediate gain
• Write the NOSC<2:0> and NDIV<3:0> bits in the setting of the internal inverter-amplifier. XT mode
OSCCON1 register to switch the system clock current consumption is the medium of the three modes.
source This mode is best suited to drive crystals and
See Section 9.3 “Clock Switching” for more resonators with a frequency range up to 4 MHz.
information. HS Oscillator mode selects the highest gain setting of the
internal inverter-amplifier. HS mode current consumption
9.2.1.1 EC Mode is the highest of the three modes. This mode is best
The External Clock (EC) mode allows an externally suited for resonators that require operating frequencies
generated logic level signal to be the system clock up to 20 MHz.
source. When operating in this mode, an external clock Figure 9-3 and Figure 9-4 show typical circuits for
source is connected to the OSC1/CLKIN input. OSC2/ quartz crystal and ceramic resonators, respectively.
CLKOUT is available for general purpose I/O or
CLKOUT. Figure 9-2 shows the pin connections for EC
mode.
EC mode has three power modes to select from through
Configuration Words:
• ECH – High power, 32 MHz
• ECM – Medium power, 8 MHz
• ECL – Low power, 0.1 MHz

 2016-2018 Microchip Technology Inc. DS40001866B-page 128


PIC16(L)F15356/75/76/85/86
FIGURE 9-3: QUARTZ CRYSTAL FIGURE 9-4: CERAMIC RESONATOR
OPERATION (LP, XT OR OPERATION
HS MODE) (XT OR HS MODE)
Rev. 10-000059A
7/30/2013

PIC® MCU

PIC® MCU OSC1/CLKIN

OSC1/CLKIN C1 To Internal
Logic
C1 To Internal
Logic RP(3) RF(2) Sleep
Quartz
(2)
Crystal RF Sleep

C2 Ceramic RS(1) OSC2/CLKOUT


OSC2/CLKOUT
C2 RS(1) Resonator

Note 1: A series resistor (RS) may be required for


Note 1: A series resistor (Rs) may be required for ceramic resonators with low drive level.
quartz crystals with low drive level.
2: The value of RF varies with the Oscillator mode
2: The value of RF varies with the Oscillator mode selected (typically between 2 M to 10 M.
selected (typically between 2 MΩ and 10 MΩ).
3: An additional parallel feedback resistor (RP)
may be required for proper ceramic resonator
operation.
Note 1: Quartz crystal characteristics vary
according to type, package and
manufacturer. The user should consult the 9.2.1.3 Oscillator Start-up Timer (OST)
manufacturer data sheets for specifications If the oscillator module is configured for LP, XT or HS
and recommended application. modes, the Oscillator Start-up Timer (OST) counts
2: Always verify oscillator performance over 1024 oscillations from OSC1. This occurs following a
the VDD and temperature range that is Power-on Reset (POR), Brown-out Reset (BOR) or a
expected for the application. wake-up from Sleep. The OST ensures that the
3: For oscillator design assistance, reference oscillator circuit, using a quartz crystal resonator or
the following Microchip Application Notes: ceramic resonator, has started and is providing a stable
system clock to the oscillator module.
• AN826, “Crystal Oscillator Basics and
Crystal Selection for rfPIC® and PIC®
Devices” (DS00826)
• AN849, “Basic PIC® Oscillator Design”
(DS00849)
• AN943, “Practical PIC® Oscillator
Analysis and Design” (DS00943)
• AN949, “Making Your Oscillator Work”
(DS00949)

 2016-2018 Microchip Technology Inc. DS40001866B-page 129


PIC16(L)F15356/75/76/85/86
9.2.1.4 4x PLL
Note 1: Quartz crystal characteristics vary
The oscillator module contains a PLL that can be used according to type, package and
with external clock sources to provide a system clock manufacturer. The user should consult the
source. The input frequency for the PLL must fall within manufacturer data sheets for specifications
specifications. See the PLL Clock Timing and recommended application.
Specifications in Table 37-9.
2: Always verify oscillator performance over
The PLL may be enabled for use by one of two the VDD and temperature range that is
methods: expected for the application.
1. Program the RSTOSC bits in the Configuration 3: For oscillator design assistance, reference
Word 1 to enable the EXTOSC with 4x PLL the following Microchip Application Notes:
(RSTOSC<2:0> = '010').
• AN826, “Crystal Oscillator Basics and
2. Write the NOSC bits in the OSCCON1 register
Crystal Selection for rfPIC® and PIC®
to enable the EXTOSC with 4x PLL
Devices” (DS00826)
(NOSC<2:0> = '010').
• AN849, “Basic PIC® Oscillator Design”
9.2.1.5 Secondary Oscillator (DS00849)
• AN943, “Practical PIC® Oscillator
The secondary oscillator is a separate oscillator block
Analysis and Design” (DS00943)
that can be used as an alternate system clock source.
The secondary oscillator is optimized for 32.768 kHz, • AN949, “Making Your Oscillator Work”
and can be used with an external crystal oscillator con- (DS00949)
nected to the SOSCI and SOSCO device pins, or an • TB097, “Interfacing a Micro Crystal
external clock source connected to the SOSCIN pin. MS1V-T1K 32.768 kHz Tuning Fork
Refer to Section 9.3 “Clock Switching” for more Crystal to a PIC16F690/SS” (DS91097)
information. • AN1288, “Design Practices for Low-
Power External Oscillators” (DS01288)
FIGURE 9-5: QUARTZ CRYSTAL
OPERATION
(SECONDARY
OSCILLATOR)

PIC® MCU

SOSCI

C1 To Internal
Logic
32.768 kHz
Quartz
Crystal

C2 SOSCO

 2016-2018 Microchip Technology Inc. DS40001866B-page 130


PIC16(L)F15356/75/76/85/86
9.2.2 INTERNAL CLOCK SOURCES 9.2.2.1 HFINTOSC
The device may be configured to use an internal The High-Frequency Internal Oscillator (HFINTOSC) is
oscillator block as the system clock by performing one a precision digitally-controlled internal clock source
of the following actions: that produces a stable clock up to 32 MHz. The
• Program the RSTOSC<2:0> bits in Configuration HFINTOSC can be enabled through one of the
Words to select the INTOSC clock source, which following methods:
will be used as the default system clock upon a • Programming the RSTOSC<2:0> bits in
device Reset. Configuration Word 1 to ‘110’ (1 MHz) or ‘001’
• Write the NOSC<2:0> bits in the OSCCON1 (32 MHz) to set the oscillator upon device Power-
register to switch the system clock source to the up or Reset.
internal oscillator during run-time. See • Write to the NOSC<2:0> bits of the OSCCON1
Section 9.3 “Clock Switching” for more register during run-time.
information. The HFINTOSC frequency can be selected by setting
In INTOSC mode, the OSC1/CLKIN pin is available for the HFFRQ<2:0> bits of the OSCFRQ register. The
general purpose I/O. The OSC2/CLKOUT pin is MFINTOSC is an internal clock source within the
available for general purpose I/O or CLKOUT. HFINTOSC that provides two (500 kHz, 32 kHz) con-
The function of the OSC2/CLKOUT pin is determined stant clock outputs. These constant clock outputs are
by the CLKOUTEN bit in Configuration Words. available for selection to various peripherals, internally.

The internal oscillator block has two independent The NDIV<3:0> bits of the OSCCON1 register allow for
oscillators that can produce two internal system clock division of the HFINTOSC output from a range between
sources. 1:1 and 1:512.

1. The HFINTOSC (High-Frequency Internal


Oscillator) is factory calibrated and operates up
to 32 MHz.
2. The LFINTOSC (Low-Frequency Internal
Oscillator) is factory-calibrated and operates at
31 kHz.

 2016-2018 Microchip Technology Inc. DS40001866B-page 131


PIC16(L)F15356/75/76/85/86
9.2.2.2 Internal Oscillator Frequency 9.3 Clock Switching
Adjustment
The system clock source can be switched between
The HFINTOSC and LFINTOSC internal oscillators are external and internal clock sources via software using
both factory-calibrated. The HFINTOSC oscillator can the New Oscillator Source (NOSC) and New Divider
be adjusted in software by writing to the OSCTUNE selection request (NDIV) bits of the OSCCON1 register.
register (Register 9-7). OSCTUNE does not affect the The following clock sources can be selected:
LFINTOSC frequency.
• External Oscillator (EXTOSC)
The default value of the OSCTUNE register is 00h. The • High-Frequency Internal Oscillator (HFINTOSC)
value is a 6-bit two’s complement number. A value of • Low-Frequency Internal Oscillator (LFINTOSC)
1Fh will provide an adjustment to the maximum • Secondary Oscillator (SOSC)
frequency. A value of 20h will provide an adjustment to • EXTOSC with 4x PLL
the minimum frequency. • HFINTOSC with 2x PLL
When the OSCTUNE register is modified, the current
HFINTOSC oscillator frequency will begin shifting to the 9.3.1 NEW OSCILLATOR SOURCE
new frequency. Code execution continues during this (NOSC) AND NEW DIVIDER
shift. There is no indication that the shift has occurred. SELECTION REQUEST (NDIV) BITS
The New Oscillator Source (NOSC) and New Divider
9.2.2.3 LFINTOSC selection request (NDIV) bits of the OSCCON1 register
The Low-Frequency Internal Oscillator (LFINTOSC) is select the system clock source and the frequency that
a factory-calibrated 31 kHz internal clock source. are used for the CPU and peripherals.
The LFINTOSC is the clock source for the Power-up When new values of NOSC and NDIV are written to
Timer (PWRT), Watchdog Timer (WDT), and Fail-Safe OSCCON1, the current oscillator selection will
Clock Monitor (FSCM). The LFINTOSC can also be continue to operate while waiting for the new clock
used as the system clock, or as a clock or input source source to indicate that it is stable and ready. In some
to certain peripherals. cases, the newly requested source may already be in
use, and is ready immediately. In the case of a divider-
The LFINTOSC is selected as the clock source through
only change, the new and old sources are the same,
one of the following methods:
and will be immediately ready. The device may enter
• Programming the RSTOSC<2:0> bits of Configu- Sleep while waiting for the switch as described in
ration Word 1 to enable LFINTOSC Section 9.3.3 “Clock Switch and Sleep”.
(RSTOSC<2:0> = '101')
When the new oscillator is ready, the New Oscillator is
• Write to the NOSC<2:0> bits of the OSCCON1 Ready (NOSCR) bit of OSCCON3 and the Clock
register (NOSC<2:0> = '101') Switch Interrupt Flag (CSWIF) bit of PIR1 become set
Peripherals that use the LFINTOSC are: (CSWIF = 1). If Clock Switch Interrupts are enabled
(CSWIE = 1), an interrupt will be generated at that time.
• Power-up Timer (PWRT)
The Oscillator Ready (ORDY) bit of OSCCON3 can
• Windowed Watchdog Timer (WWDT)
also be polled to determine when the oscillator is ready
• Timer1
in lieu of an interrupt.
• Timer0
• Timer2 If the Clock Switch Hold (CSWHOLD) bit of OSCCON3
• Fail-Safe Clock Monitor (FSCM) is clear, the oscillator switch will occur when the new
• CLKR Oscillator’s READY bit (NOSCR) is set, and the
• CLC interrupt (if enabled) will be serviced at the new
oscillator setting.
9.2.2.4 Oscillator Status and Manual Enable If CSWHOLD is set, the oscillator switch is suspended,
The ‘ready’ status of each oscillator is displayed in the while execution continues using the current (old) clock
OSCSTAT register (Register 9-4). The oscillators can source. When the NOSCR bit is set, software should:
also be manually enabled through the OSCEN register • set CSWHOLD = 0 so the switch can complete, or
(Register 9-7). Manual enabling makes it possible to • copy COSC into NOSC to abandon the switch.
verify the operation of the EXTOSC or SOSC crystal If DOZE is in effect, the switch occurs on the next clock
oscillators. This can be achieved by enabling the cycle, whether or not the CPU is operating during that
selected oscillator, then watching the corresponding cycle.
‘ready’ state of the oscillator in the OSCSTAT register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 132


PIC16(L)F15356/75/76/85/86
Changing the clock post-divider without changing the 9.3.3 CLOCK SWITCH AND SLEEP
clock source (e.g., changing FOSC from 1 MHz to 2
If OSCCON1 is written with a new value and the device
MHz) is handled in the same manner as a clock source
is put to Sleep before the switch completes, the switch
change, as described previously. The clock source will
will not take place and the device will enter Sleep
already be active, so the switch is relatively quick.
mode.
CSWHOLD must be clear (CSWHOLD = 0) for the
switch to complete. When the device wakes from Sleep and the
The current COSC and CDIV are indicated in the CSWHOLD bit is clear, the device will wake with the
OSCCON2 register up to the moment when the switch ‘new’ clock active, and the clock switch interrupt flag bit
actually occurs, at which time OSCCON2 is updated (CSWIF) will be set.
and ORDY is set. NOSCR is cleared by hardware to When the device wakes from Sleep and the
indicate that the switch is complete. CSWHOLD bit is set, the device will wake with the ‘old’
clock active and the new clock will be requested again.
9.3.2 PLL INPUT SWITCH
Switching between the PLL and any non-PLL source is
managed as described above. The input to the PLL is
established when NOSC selects the PLL, and main-
tained by the COSC setting.
When NOSC and COSC select the PLL with different
input sources, the system continues to run using the
COSC setting, and the new source is enabled per
NOSC. When the new oscillator is ready (and
CSWHOLD = 0), system operation is suspended while
the PLL input is switched and the PLL acquires lock.

Note: If the PLL fails to lock, the FSCM will


trigger.

FIGURE 9-6: CLOCK SWITCH (CSWHOLD = 0)


OSCCON1
WRITTEN

OSC #1 OSC #2

ORDY

NOTE 2
NOSCR

NOTE 1
CSWIF

USER
CSWHOLD CLEAR

Note 1:CSWIF is asserted coincident with NOSCR; interrupt is serviced at OSC#2 speed.
2: The assertion of NOSCR is hidden from the user because it appears only for the duration of the switch.

 2016-2018 Microchip Technology Inc. DS40001866B-page 133


PIC16(L)F15356/75/76/85/86
FIGURE 9-7: CLOCK SWITCH (CSWHOLD = 1)
OSCCON1
WRITTEN

OSC #1 OSC #2

ORDY

NOSCR

NOTE 1
CSWIF

USER
CSWHOLD CLEAR

Note 1:CSWIF is asserted coincident with NOSCR, and may be cleared before or after clearing CSWHOLD = 0.

FIGURE 9-8: CLOCK SWITCH ABANDONED


OSCCON1 OSCCON1
WRITTEN WRITTEN

OSC #1

ORDY NOTE 2

NOSCR

NOTE 1
CSWIF

CSWHOLD

Note 1:CSWIF may be cleared before or after rewriting OSCCON1; CSWIF is not automatically cleared.
2: ORDY = 0 if OSCCON1 does not match OSCCON2; a new switch will begin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 134


PIC16(L)F15356/75/76/85/86
9.4 Fail-Safe Clock Monitor 9.4.2 FAIL-SAFE OPERATION
The Fail-Safe Clock Monitor (FSCM) allows the device When the external clock fails, the FSCM switches the
to continue operating should the external oscillator fail. device clock to the HFINTOSC at 1 MHz clock
The FSCM is enabled by setting the FCMEN bit in frequency and sets the bit flag OSFIF of the PIR1
Configuration Word 1. The FSCM is applicable to all register. Setting this flag will generate an interrupt if the
external Oscillator modes (LP, XT, HS, ECL, ECM, OSFIE bit of the PIE1 register is also set. The device
ECH and Secondary Oscillator). firmware can then take steps to mitigate the problems
that may arise from a failed clock. The system clock will
continue to be sourced from the internal clock source
FIGURE 9-9: FSCM BLOCK DIAGRAM
until the device firmware successfully restarts the
Clock Monitor external oscillator and switches back to external
Latch operation, by writing to the NOSC and NDIV bits of the
External OSCCON1 register.
S Q
Clock
9.4.3 FAIL-SAFE CONDITION CLEARING
LFINTOSC The Fail-Safe condition is cleared after a Reset,
÷ 64 R Q
Oscillator executing a SLEEP instruction or changing the NOSC
and NDIV bits of the OSCCON1 register. When
31 kHz 488 Hz switching to the external oscillator, or external oscillator
(~32 s) (~2 ms)
and PLL, the OST is restarted. While the OST is
Sample Clock running, the device continues to operate from the
Clock INTOSC selected in OSCCON1. When the OST times
Failure
out, the Fail-Safe condition is cleared after successfully
Detected
switching to the external clock source. The OSFIF bit
should be cleared prior to switching to the external
9.4.1 FAIL-SAFE DETECTION clock source. If the Fail-Safe condition still exists, the
OSFIF flag will again become set by hardware.
The FSCM module detects a failed oscillator by
comparing the external oscillator to the FSCM sample 9.4.4 RESET OR WAKE-UP FROM SLEEP
clock. The sample clock is generated by dividing the
LFINTOSC by 64. See Figure 9-9. Inside the fail The FSCM is designed to detect an oscillator failure
detector block is a latch. The external clock sets the after the Oscillator Start-up Timer (OST) has expired.
latch on each falling edge of the external clock. The The OST is used after waking up from Sleep and after
sample clock clears the latch on each rising edge of the any type of Reset. The OST is not used with the EC
sample clock. A failure is detected when an entire half- Clock modes so that the FSCM will be active as soon
cycle of the sample clock elapses before the external as the Reset or wake-up has completed. Therefore, the
clock goes low. device will always be executing code while the OST is
operating.

FIGURE 9-10: FSCM TIMING DIAGRAM

Sample Clock

System Oscillator
Clock Failure
Output

Clock Monitor Output


(Q)
Failure
Detected
OSCFIF

Test Test Test

Note: The system clock is normally at a much higher frequency than the sample clock. The relative frequencies in
this example have been chosen for clarity.

 2016-2018 Microchip Technology Inc. DS40001866B-page 135


PIC16(L)F15356/75/76/85/86
9.5 Register Definitions: Oscillator Control

REGISTER 9-1: OSCCON1: OSCILLATOR CONTROL REGISTER1


U-0 R/W-f/f(1) R/W-f/f(1) R/W-f/f(1) R/W-q/q R/W-q/q R/W-q/q R/W-q/q
(2,3)
— NOSC<2:0> NDIV<3:0>(2,3,4)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared f = determined by fuse setting

bit 7 Unimplemented: Read as ‘0’


bit 6-4 NOSC<2:0>: New Oscillator Source Request bits
The setting requests a source oscillator and PLL combination per Table 9-1.
POR value = RSTOSC (Register 5-1).
bit 3-0 NDIV<3:0>: New Divider Selection Request bits
The setting determines the new postscaler division ratio per Table 9-1.

Note 1: The default value (f/f) is set equal to the RSTOSC Configuration bits.
2: If NOSC is written with a reserved value (Table 9-1), the operation is ignored and neither NOSC nor NDIV
is written.
3: When CSWEN = 0, this register is read-only and cannot be changed from the POR value.
4: When NOSC = 110 (HFINTOSC 1 MHz), the NDIV bits will default to ‘0010’ upon Reset; for all other
NOSC settings the NDIV bits will default to ‘0000’ upon Reset.

REGISTER 9-2: OSCCON2: OSCILLATOR CONTROL REGISTER 2


U-0 R-n/n(2) R-n/n(2) R-n/n(2) R-n/n(2) R-n/n(2) R-n/n(2) R-n/n(2)
— COSC<2:0> CDIV<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 Unimplemented: Read as ‘0’


bit 6-4 COSC<2:0>: Current Oscillator Source Select bits (read-only)
Indicates the current source oscillator and PLL combination per Table 9-1.
bit 3-0 CDIV<3:0>: Current Divider Select bits (read-only)
Indicates the current postscaler division ratio per Table 9-1.

Note 1:The POR value is the value present when user code execution begins.
2: The Reset value (n/n) is the same as the NOSC/NDIV bits.

 2016-2018 Microchip Technology Inc. DS40001866B-page 136


PIC16(L)F15356/75/76/85/86

TABLE 9-1: NOSC/COSC BIT SETTINGS TABLE 9-2: NDIV/CDIV BIT SETTINGS
NOSC<2:0>/ NDIV<3:0>/
Clock Source Clock divider
COSC<2:0> CDIV<3:0>
111 EXTOSC(1) 1111-1010 Reserved
110 HFINTOSC (1-32 MHz)(2) 1001 512
101 LFINTOSC 1000 256
100 SOSC 0111 128
011 Reserved 0110 64
010 EXTOSC with 4x PLL(1) 0101 32
001 HFINTOSC with 2x PLL (32 MHz)(1) 0100 16
000 Reserved 0011 8
Note 1: EXTOSC configured by the FEXTOSC bits of 0010 4
Configuration Word 1 (Register 5-1). 0001 2
2: HFINTOSC settings are configured with the
0000 1
HFFRQ bits of the OSCFRQ register
(Register 9-6).

REGISTER 9-3: OSCCON3: OSCILLATOR CONTROL REGISTER 3


R/W/HC-0/0 R/W-0/0 U-0 R-0/0 R-0/0 U-0 U-0 U-0
CSWHOLD SOSCPWR — ORDY NOSCR — — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 CSWHOLD: Clock Switch Hold bit


1 = Clock switch will hold (with interrupt) when the oscillator selected by NOSC is ready
0 = Clock switch may proceed when the oscillator selected by NOSC is ready; if this bit
is clear at the time that NOSCR becomes ‘1’, the switch will occur
bit 6 SOSCPWR: Secondary Oscillator Power Mode Select bit
1 = Secondary oscillator operating in High-power mode
0 = Secondary oscillator operating in Low-power mode
bit 5 Unimplemented: Read as ‘0’.
bit 4 ORDY: Oscillator Ready bit (read-only)
1 = OSCCON1 = OSCCON2; the current system clock is the clock specified by NOSC
0 = A clock switch is in progress
bit 3 NOSCR: New Oscillator is Ready bit (read-only)
1 = A clock switch is in progress and the oscillator selected by NOSC indicates a “ready” condition
0 = A clock switch is not in progress, or the NOSC-selected oscillator is not yet ready
bit 2-0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 137


PIC16(L)F15356/75/76/85/86
REGISTER 9-4: OSCSTAT: OSCILLATOR STATUS REGISTER 1
R-q/q R-q/q R-q/q R-q/q R-q/q R-q/q U-0 R-q/q
EXTOR HFOR MFOR LFOR SOR ADOR — PLLR
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Reset value is determined by hardware

bit 7 EXTOR: EXTOSC (external) Oscillator Ready bit


1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 6 HFOR: HFINTOSC Oscillator Ready bit
1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 5 MFOR: MFINTOSC Oscillator Ready bit
1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 4 LFOR: LFINTOSC Oscillator Ready bit
1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 3 SOR: Secondary (Timer1) Oscillator Ready bit
1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 2 ADOR: CRC Oscillator Ready bit
1 = The oscillator is ready to be used
0 = The oscillator is not enabled, or is not yet ready to be used.
bit 1 Unimplemented: Read as ‘0’
bit 0 PLLR: PLL is Ready bit
1 = The PLL is ready to be used
0 = The PLL is not enabled, the required input source is not ready, or the PLL is not locked.

 2016-2018 Microchip Technology Inc. DS40001866B-page 138


PIC16(L)F15356/75/76/85/86

REGISTER 9-5: OSCEN: OSCILLATOR MANUAL ENABLE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0
EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 EXTOEN: External Oscillator Manual Request Enable bit(1)


1 = EXTOSC is explicitly enabled, operating as specified by FEXTOSC
0 = EXTOSC could be enabled by some modules
bit 6 HFOEN: HFINTOSC Oscillator Manual Request Enable bit
1 = HFINTOSC is explicitly enabled, operating as specified by OSCFRQ
0 = HFINTOSC could be enabled by another module
bit 5 MFOEN: MFINTOSC Oscillator Manual Request Enable bit
1 = MFINTOSC is explicitly enabled
0 = MFINTOSC could be enabled by another module
bit 4 LFOEN: LFINTOSC (31 kHz) Oscillator Manual Request Enable bit
1 = LFINTOSC is explicitly enabled
0 = LFINTOSC could be enabled by another module
bit 3 SOSCEN: Secondary (Timer1) Oscillator Manual Request bit
1 = Secondary oscillator is explicitly enabled, operating as specified by SOSCPWR
0 = Secondary oscillator could be enabled by another module
bit 2 ADOEN: FRC Oscillator Manual Request Enable bit
1 = FRC is explicitly enabled
0 = FRC could be enabled by another module
bit 1-0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 139


PIC16(L)F15356/75/76/85/86
REGISTER 9-6: OSCFRQ: HFINTOSC FREQUENCY SELECTION REGISTER
U-0 U-0 U-0 U-0 U-0 R/W-q/q R/W-q/q R/W-q/q
— — — — — HFFRQ<2:0>(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 HFFRQ<2:0>: HFINTOSC Frequency Selection bits
Nominal Freq (MHz):
111 = Reserved
110 = 32
101 = 16
100 = 12
011 = 8
010 = 4
001 = 2
000 = 1
Note 1: When RSTOSC=110 (HFINTOSC 1 MHz), the HFFRQ bits will default to ‘010’ upon Reset; when RSTOSC = 000
(HFINTOSC 32 MHz), the HFFRQ bits will default to ‘110’ upon Reset.

 2016-2018 Microchip Technology Inc. DS40001866B-page 140


PIC16(L)F15356/75/76/85/86
REGISTER 9-7: OSCTUNE: HFINTOSC TUNING REGISTER
U-0 U-0 R/W-1/1 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — HFTUN<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’.


bit 5-0 HFTUN<5:0>: HFINTOSC Frequency Tuning bits
01 1111 = Maximum frequency
01 1110 =
•••
00 0001 =
00 0000 = Center frequency. Oscillator module is running at the calibrated frequency (default value).
11 1111 =
•••
10 0001 =
10 0000 = Minimum frequency.

 2016-2018 Microchip Technology Inc. DS40001866B-page 141


PIC16(L)F15356/75/76/85/86
TABLE 9-3: SUMMARY OF REGISTERS ASSOCIATED WITH CLOCK SOURCES
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

OSCCON1 — NOSC<2:0> NDIV<3:0> 136


OSCCON2 — COSC<2:0> CDIV<3:0> 136
OSCCON3 CWSHOLD SOSCPWR — ORDY NOSCR — — — 137
OSCFRQ — — — — — HFFRQ<2:0> 140
OSCSTAT EXTOR HFOR MFOR LFOR SOR ADOR — PLLR 138
OSCTUNE — — HFTUN<5:0> 141
OSCEN EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN — — 139
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by clock sources.

TABLE 9-4: SUMMARY OF CONFIGURATION WORD WITH CLOCK SOURCES


Register
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0
on Page

13:8 — — FCMEN — CSWEN — — CLKOUTEN


CONFIG1 102
7:0 — RSTOSC<2:0> — FEXTOSC<2:0>
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by clock sources.

 2016-2018 Microchip Technology Inc. DS40001866B-page 142


PIC16(L)F15356/75/76/85/86
10.0 INTERRUPTS
The interrupt feature allows certain events to preempt
normal program flow. Firmware is used to determine
the source of the interrupt and act accordingly. Some
interrupts can be configured to wake the MCU from
Sleep mode.
This chapter contains the following information for
Interrupts:
• Operation
• Interrupt Latency
• Interrupts During Sleep
• INT Pin
• Automatic Context Saving
Many peripherals produce interrupts. Refer to the
corresponding chapters for details.
A block diagram of the interrupt logic is shown in
Figure 10-1.

FIGURE 10-1: INTERRUPT LOGIC


Rev. 10-000010C
10/12/2016

TMR0IF Wake-up
TMR0IE (If in Sleep mode)

INTF
Peripheral Interrupts INTE

(ADIF) PIR1 <0>


IOCIF
(ADIE) PIE1 <0> Interrupt
IOCIE to CPU

PEIE

PIRn
PIEn GIE

 2016-2018 Microchip Technology Inc. DS40001866B-page 143


PIC16(L)F15356/75/76/85/86
10.1 Operation 10.2 Interrupt Latency
Interrupts are disabled upon any device Reset. They Interrupt latency is defined as the time from when the
are enabled by setting the following bits: interrupt event occurs to the time code execution at the
• GIE bit of the INTCON register interrupt vector begins. The interrupt is sampled during
Q1 of the instruction cycle. The actual interrupt latency
• Interrupt Enable bit(s) of the PIEx[y] registers for
then depends on the instruction that is executing at the
the specific interrupt event(s)
time the interrupt is detected. See Figure 10-2 and
• PEIE bit of the INTCON register (if the Interrupt Figure 10-3 for more details.
Enable bit of the interrupt event is contained in the
PIEx registers)
The PIR1, PIR2, PIR3, PIR4, PIR5, PIR6, and PIR7
registers record individual interrupts via interrupt flag
bits. Interrupt flag bits will be set, regardless of the
status of the GIE, PEIE and individual interrupt enable
bits.
The following events happen when an interrupt event
occurs while the GIE bit is set:
• Current prefetched instruction is flushed
• GIE bit is cleared
• Current Program Counter (PC) is pushed onto the
stack
• Critical registers are automatically saved to the
shadow registers (See “Section 10.5 “Auto-
matic Context Saving”)
• PC is loaded with the interrupt vector 0004h
The firmware within the Interrupt Service Routine (ISR)
should determine the source of the interrupt by polling
the interrupt flag bits. The interrupt flag bits must be
cleared before exiting the ISR to avoid repeated
interrupts. Because the GIE bit is cleared, any interrupt
that occurs while executing the ISR will be recorded
through its interrupt flag, but will not cause the
processor to redirect to the interrupt vector.
The RETFIE instruction exits the ISR by popping the
previous address from the stack, restoring the saved
context from the shadow registers and setting the GIE
bit.
For additional information on a specific interrupts
operation, refer to its peripheral chapter.
Note 1: Individual interrupt flag bits are set,
regardless of the state of any other
enable bits.
2: All interrupts will be ignored while the GIE
bit is cleared. Any interrupt occurring
while the GIE bit is clear will be serviced
when the GIE bit is set again.

 2016-2018 Microchip Technology Inc. DS40001866B-page 144


PIC16(L)F15356/75/76/85/86
FIGURE 10-2: INTERRUPT LATENCY
Rev. 10-000269E
8/31/2016

OSC1

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

CLKOUT

INT
pin
Valid Interrupt
window(1) 1 Cycle Instruction at PC

Fetch PC - 1 PC PC + 1 PC = 0x0004 PC = 0x0005 PC = 0x0006

Execute PC - 2 PC - 1 PC 123 123 PC = 0x0004 PC = 0x0005

Indeterminate Latency
Latency(2)

Note 1: An interrupt may occur at any time during the interrupt window.
2: Since an interrupt may occur any time during the interrupt window, the actual latency can vary.

FIGURE 10-3: INT PIN INTERRUPT TIMING

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

(4)

INT pin
(1)
(1)
INTF (5) Interrupt Latency (2)

GIE

INSTRUCTION FLOW
PC PC PC + 1 PC + 1 0004h 0005h
Instruction
Fetched Inst (PC) Inst (PC + 1) — Inst (0004h) Inst (0005h)

Instruction Inst (0004h)


Inst (PC – 1) Inst (PC) Forced NOP Forced NOP
Executed

Note 1: INTF flag is sampled here (every Q1).


2: Asynchronous interrupt latency = 3-5 TCY. Synchronous latency = 3-4 TCY, where TCY = instruction cycle time.
Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3: For minimum width of INT pulse, refer to AC specifications in Section 37.0 “Electrical Specifications”.
4: INTF may be set any time during the Q4-Q1 cycles.

 2016-2018 Microchip Technology Inc. DS40001866B-page 145


PIC16(L)F15356/75/76/85/86
10.3 Interrupts During Sleep
Interrupts can be used to wake from Sleep. To wake
from Sleep, the peripheral must be able to operate
without the system clock. The interrupt source must
have the appropriate Interrupt Enable bit(s) set prior to
entering Sleep.
On waking from Sleep, if the GIE bit is also set, the
processor will branch to the interrupt vector. Otherwise,
the processor will continue executing instructions after
the SLEEP instruction. The instruction directly after the
SLEEP instruction will always be executed before
branching to the ISR. Refer to Section 11.0 “Power-
Saving Operation Modes” for more details.

10.4 INT Pin


The INT pin can be used to generate an asynchronous
edge-triggered interrupt. Refer to Figure 10-3. This
interrupt is enabled by setting the INTE bit of the PIE0
register. The INTEDG bit of the INTCON register
determines on which edge the interrupt will occur. When
the INTEDG bit is set, the rising edge will cause the
interrupt. When the INTEDG bit is clear, the falling edge
will cause the interrupt. The INTF bit of the PIR0 register
will be set when a valid edge appears on the INT pin. If
the GIE and INTE bits are also set, the processor will
redirect program execution to the interrupt vector.

10.5 Automatic Context Saving


Upon entering an interrupt, the return PC address is
saved on the stack. Additionally, the following registers
are automatically saved in the shadow registers:
• W register
• STATUS register (except for TO and PD)
• BSR register
• FSR registers
• PCLATH register
Upon exiting the Interrupt Service Routine, these
registers are automatically restored. Any modifications
to these registers during the ISR will be lost. If
modifications to any of these registers are desired, the
corresponding shadow register should be modified and
the value will be restored when exiting the ISR. The
shadow registers are available in Bank 31 and are
readable and writable. Depending on the user’s
application, other registers may also need to be saved.

 2016-2018 Microchip Technology Inc. DS40001866B-page 146


PIC16(L)F15356/75/76/85/86
10.6 Register Definitions: Interrupt Control

REGISTER 10-1: INTCON: INTERRUPT CONTROL REGISTER


R/W-0/0 R/W-0/0 U-0 U-0 U-0 U-0 U-0 R/W-1/1
GIE PEIE — — — — — INTEDG
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 GIE: Global Interrupt Enable bit


1 = Enables all active interrupts
0 = Disables all interrupts
bit 6 PEIE: Peripheral Interrupt Enable bit
1 = Enables all active peripheral interrupts
0 = Disables all peripheral interrupts
bit 5-1 Unimplemented: Read as ‘0’
bit 0 INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of INT pin
0 = Interrupt on falling edge of INT pin

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 147


PIC16(L)F15356/75/76/85/86

REGISTER 10-2: PIE0: PERIPHERAL INTERRUPT ENABLE REGISTER 0


U-0 U-0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0
— — TMR0IE IOCIE — — — INTE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-6 Unimplemented: Read as ‘0’


bit 5 TMR0IE: Timer0 Overflow Interrupt Enable bit
1 = Enables the Timer0 interrupt
0 = Disables the Timer0 interrupt
bit 4 IOCIE: Interrupt-on-Change Interrupt Enable bit
1 = Enables the IOC change interrupt
0 = Disables the IOC change interrupt
bit 3-1 Unimplemented: Read as ‘0’
bit 0 INTE: INT External Interrupt Flag bit(1)
1 = Enables the INT external interrupt
0 = Disables the INT external interrupt

Note 1: The External Interrupt INT pin is selected by INTPPS (Register 15-1).

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by PIE1-PIE7. Interrupt sources
controlled by the PIE0 register do not
require PEIE to be set in order to allow
interrupt vectoring (when GIE is set).

 2016-2018 Microchip Technology Inc. DS40001866B-page 148


PIC16(L)F15356/75/76/85/86
REGISTER 10-3: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
R/W-0/0 R/W-0/0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
OSFIE CSWIE — — — — — ADIE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 OSFIE: Oscillator Fail Interrupt Enable bit


1 = Enables the Oscillator Fail Interrupt
0 = Disables the Oscillator Fail Interrupt
bit 6 CSWIE: Clock Switch Complete Interrupt Enable bit
1 = The clock switch module interrupt is enabled
0 = The clock switch module interrupt is disabled
bit 5-1 Unimplemented: Read as ‘0’
bit 0 ADIE: Analog-to-Digital Converter (ADC) Interrupt Enable bit
1 = Enables the ADC interrupt
0 = Disables the ADC interrupt

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7

 2016-2018 Microchip Technology Inc. DS40001866B-page 149


PIC16(L)F15356/75/76/85/86

REGISTER 10-4: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2


U-0 R/W-0/0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
— ZCDIE — — — — C2IE C1IE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 Unimplemented: Read as ‘0’


bit 6 ZCDIE: Zero-Cross Detection (ZCD) Interrupt Enable bit
1 = Enables the ZCD interrupt
0 = Disables the ZCD interrupt
bit 5-2 Unimplemented: Read as ‘0’
bit 1 C2IE: Comparator C2 Interrupt Enable bit
1 = Enables the Comparator C2 interrupt
0 = Disables the Comparator C2 interrupt
bit 0 C1IE: Comparator C1 Interrupt Enable bit
1 = Enables the Comparator C1 interrupt
0 = Disables the Comparator C1 interrupt

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 150


PIC16(L)F15356/75/76/85/86

REGISTER 10-5: PIE3: PERIPHERAL INTERRUPT ENABLE REGISTER 3


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
RC2IE TX2IE RC1IE TX1IE BCL2IE SSP2IE BCL1IE SSP1IE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 RC2IE: USART2 Receive Interrupt Enable bit


1 = Enables the USART2 receive interrupt
0 = Disables the USART2 receive interrupt
bit 6 TX2IE: USART2 Transmit Interrupt Enable bit
1 = Enables the USART2 transmit interrupt
0 = Disables the USART2 transmit interrupt
bit 5 RC1IE: USART1 Receive Interrupt Enable bit
1 = Enables the USART1 receive interrupt
0 = Disables the USART1 receive interrupt
bit 4 TX1IE: USART1 Transmit Interrupt Enable bit
1 = Enables the USART1 transmit interrupt
0 = Disables the USART1 transmit interrupt
bit 3 BCL2IE: MSSP2 Bus Collision Interrupt Enable bit
1 = MSSP bus Collision interrupt enabled
0 = MSSP bus Collision interrupt disabled
bit 2 SSP2IE: MSSP2 Interrupt Enable bit
1 = Enables the MSSP2 Interrupt
0 = Disables the MSSP Interrupt
bit 1 BCL1IE: MSSP1 Bus Collision Interrupt Enable bit
1 = MSSP1 bus collision interrupt enabled
0 = MSSP1 bus collision interrupt disabled
bit 0 SSP1IE: MSSP1 Interrupt Enable bit
1 = Enables the MSSP1 interrupt
0 = Disables the MSSP1 interrupt

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 151


PIC16(L)F15356/75/76/85/86

REGISTER 10-6: PIE4: PERIPHERAL INTERRUPT ENABLE REGISTER 4


U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
— — — — — — TMR2IE TMR1IE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-2 Unimplemented: Read as ‘0’


bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the Timer2 to PR2 match interrupt
0 = Disables the Timer2 to PR2 match interrupt
bit 0 TMR1IE: Timer1 Overflow Interrupt Enable bit
1 = Enables the Timer1 overflow interrupt
0 = Enables the Timer1 overflow interrupt

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 152


PIC16(L)F15356/75/76/85/86

REGISTER 10-7: PIE5: PERIPHERAL INTERRUPT ENABLE REGISTER 5


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0
CLC4IE CLC3IE CLC2IE CLC1IE — — — TMR1GIE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7 CLC4IE: CLC4 Interrupt Enable bit


1 = CLC4 interrupt enabled
0 = CLC4 interrupt disabled
bit 6 CLC3IE: CLC3 Interrupt Enable bit
1 = CLC3 interrupt enabled
0 = CLC3 interrupt disabled
bit 5 CLC2IE: CLC2 Interrupt Enable bit
1 = CLC2 interrupt enabled
0 = CLC2 interrupt disabled
bit 4 CLC1IE: CLC1 Interrupt Enable bit
1 = CLC1 interrupt enabled
0 = CLC1 interrupt disabled
bit 3-1 Unimplemented: Read as ‘0’
bit 0 TMR1GIE: Timer1 Gate Interrupt Enable bit
1 = Enables the Timer1 gate acquisition interrupt
0 = Disables the Timer1 gate acquisition interrupt

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 153


PIC16(L)F15356/75/76/85/86

REGISTER 10-8: PIE6: PERIPHERAL INTERRUPT ENABLE REGISTER 6


U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
— — — — — — CCP2IE CCP1IE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-2 Unimplemented: Read as ‘0’.


bit 1 CCP2IE: CCP2 Interrupt Enable bit
1 = CCP2 interrupt is enabled
0 = CCP2 interrupt is disabled
bit 0 CCP1IE: CCP1 Interrupt Enable bit
1 = CCP1 interrupt is enabled
0 = CCP1 interrupt is disabled

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 154


PIC16(L)F15356/75/76/85/86

REGISTER 10-9: PIE7: PERIPHERAL INTERRUPT ENABLE REGISTER 7


U-0 U-0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0
— — NVMIE NCO1IE — — — CWG1IE
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-6 Unimplemented: Read as ‘0’.


bit 5 NVMIE: NVM Interrupt Enable bit
1 = NVM task complete interrupt enabled
0 = NVM interrupt not enabled
bit 4 NCO1IE: NCO Interrupt Enable bit
1 = NCO rollover interrupt enabled
0 = NCO rollover interrupt disabled
bit 3-1 Unimplemented: Read as ‘0’.
bit 0 CWG1IE: CWG1 Interrupt Enable bit
1 = CWG1 interrupt is enabled
0 = CWG1 interrupt disabled

Note: Bit PEIE of the INTCON register must be


set to enable any peripheral interrupt
controlled by registers PIE1-PIE7.

 2016-2018 Microchip Technology Inc. DS40001866B-page 155


PIC16(L)F15356/75/76/85/86

REGISTER 10-10: PIR0: PERIPHERAL INTERRUPT STATUS REGISTER 0


U-0 U-0 R/W/HS-0/0 R-0 U-0 U-0 U-0 R/W/HS-0/0
— — TMR0IF IOCIF — — — INTF(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS= Hardware Set

bit 7-6 Unimplemented: Read as ‘0’


bit 5 TMR0IF: Timer0 Overflow Interrupt Flag bit
1 = Timer0 register has overflowed (must be cleared in software)
0 = Timer0 register did not overflow
bit 4 IOCIF: Interrupt-on-Change Interrupt Flag bit (read-only)(2)
1 = One or more of the IOCAF-IOCEF register bits are currently set, indicating an enabled edge was
detected by the IOC module.
0 = None of the IOCAF-IOCEF register bits are currently set
bit 3-1 Unimplemented: Read as ‘0’
bit 0 INTF: INT External Interrupt Flag bit(1)
1 = The INT external interrupt occurred (must be cleared in software)
0 = The INT external interrupt did not occur

Note 1: The External Interrupt INT pin is selected by INTPPS (Register 15-1).
2: The IOCIF bit is the logical OR of all the IOCAF-IOCEF flags. Therefore, to clear the IOCIF flag,
application firmware must clear all of the lower level IOCAF-IOCEF register bits.

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state
of its corresponding enable bit or the
Global Enable bit, GIE, of the INTCON
register. User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 156


PIC16(L)F15356/75/76/85/86

REGISTER 10-11: PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1


R/W/HS-0/0 R/W/HS-0/0 U-0 U-0 U-0 U-0 U-0 R/W/HS-0/0
OSFIF CSWIF — — — — — ADIF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7 OSFIF: Oscillator Fail-Safe Interrupt Flag bit


1 = Oscillator fail-safe interrupt has occurred (must be cleared in software)
0 = No oscillator fail-safe interrupt
bit 6 CSWIF: Clock Switch Complete Interrupt Flag bit
1 = The clock switch module indicates an interrupt condition and is ready to complete the clock switch
operation (must be cleared in software)
0 = The clock switch does not indicate an interrupt condition
bit 5-1 Unimplemented: Read as ‘0’
bit 0 ADIF: Analog-to-Digital Converter (ADC) Interrupt Flag bit
1 = An A/D conversion or complex operation has completed (must be cleared in software)
0 = An A/D conversion or complex operation is not complete

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 157


PIC16(L)F15356/75/76/85/86
REGISTER 10-12: PIR2: PERIPHERAL INTERRUPT REQUEST REGISTER 2
U-0 R/W/HS-0/0 U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0
— ZCDIF — — — — C2IF C1IF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7 Unimplemented: Read as ‘0’


bit 6 ZCDIF: Zero-Cross Detect (ZCD1) Interrupt Flag bit
1 = An enabled rising and/or falling ZCD1 event has been detected (must be cleared in software)
0 = No ZCD1 event has occurred
bit 5-2 Unimplemented: Read as ‘0’
bit 1 C2IF: Comparator C2 Interrupt Flag bit
1 = Comparator 2 interrupt asserted (must be cleared in software)
0 = Comparator 2 interrupt not asserted
bit 0 C1IF: Comparator C1 Interrupt Flag bit
1 = Comparator 1 interrupt asserted (must be cleared in software)
0 = Comparator 1 interrupt not asserted

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 158


PIC16(L)F15356/75/76/85/86
REGISTER 10-13: PIR3: PERIPHERAL INTERRUPT REQUEST REGISTER 3
R/HS-0/0 R/HS-0/0 R/HS-0/0 R/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
RC2IF TX2IF RC1IF TX1IF BCL2IF SSP2IF BCL1IF SSP1IF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware clearable

bit 7 RC2IF: EUSART2 Receive Interrupt Flag bit(1)


1 = The EUSART2 receive buffer is not empty (contains at least one byte)
0 = The EUSART2 receive buffer is empty
bit 6 TX2IF: EUSART2 Transmit Interrupt Flag bit(2)
1 = The EUSART2 transmit buffer contains at least one unoccupied space
0 = The EUSART2 transmit buffer is currently full. The application firmware should not write to
TXxREG
bit 5 RC1IF: EUSART1 Receive Interrupt Flag bit (1)
1 = The EUSART1 receive buffer is not empty (contains at least one byte)
0 = The EUSART1 receive buffer is empty
bit 4 TX1IF: EUSART1 Transmit Interrupt Flag bit(2)
1 = The EUSART1 transmit buffer contains at least one unoccupied space
0 = The EUSART1 transmit buffer is currently full. The application firmware should not write to
TXxREG.
bit 3 BCL2IF: MSSP2 Bus Collision Interrupt Flag bit
1 = A bus collision was detected (must be cleared in software)
0 = No bus collision was detected
bit 2 SSP2IF: MSSP2 Interrupt Flag bit
1 = The Transmission/Reception/Bus Condition is complete (must be cleared in software)
0 = Waiting for the Transmission/Reception/Bus Condition in progress
bit 1 BCL1IF: MSSP1 Bus Collision Interrupt Flag bit
1 = A bus collision was detected (must be cleared in software)
0 = No bus collision was detected
bit 0 SSP1IF: MSSP1 Interrupt Flag bit
1 = The Transmission/Reception/Bus Condition is complete (must be cleared in software)
0 = Waiting for the Transmission/Reception/Bus Condition in progress

Note 1: The RCxIF flag is a read-only bit. To clear the RCxIF flag, the firmware must read from RCxREG enough
times to remove all bytes from the receive buffer.
2: The TXxIF flag is a read-only bit, indicating if there is room in the transmit buffer. To clear the TX1IF flag,
the firmware must write enough data to TXxREG to completely fill all available bytes in the buffer. The
TXxIF flag does not indicate transmit completion (use TRMT for this purpose instead).

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 159


PIC16(L)F15356/75/76/85/86
REGISTER 10-14: PIR4: PERIPHERAL INTERRUPT REQUEST REGISTER 4
U-0 U-0 U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0
— — — — — — TMR2IF TMR1IF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-2 Unimplemented: Read as ‘0’


bit 1 TRM2IF: Timer2 Interrupt Flag bit
1 = The TMR2 postscaler overflowed, or in 1:1 mode, a TMR2 to PR2 match occurred (must be cleared
in software)
0 = No TMR2 event has occurred
bit 0 TRM1IF: Timer1 Overflow Interrupt Flag bit
1 = Timer1 overflow occurred (must be cleared in software)
0 = No Timer1 overflow occurred

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 160


PIC16(L)F15356/75/76/85/86

REGISTER 10-15: PIR5: PERIPHERAL INTERRUPT REQUEST REGISTER 5


R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 U-0 U-0 U-0 R/W/HS-0/0
CLC4IF CLC3IF CLC2IF CLC1IF — — — TMR1GIF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7 CLC4IF: CLC4 Interrupt Flag bit


1 = A CLC4OUT interrupt condition has occurred (must be cleared in software)
0 = No CLC4 interrupt event has occurred
bit 6 CLC3IF: CLC3 Interrupt Flag bit
1 = A CLC3OUT interrupt condition has occurred (must be cleared in software)
0 = No CLC3 interrupt event has occurred
bit 5 CLC2IF: CLC2 Interrupt Flag bit
1 = A CLC2OUT interrupt condition has occurred (must be cleared in software)
0 = No CLC2 interrupt event has occurred
bit 4 CLC1IF: CLC1 Interrupt Flag bit
1 = A CLC1OUT interrupt condition has occurred (must be cleared in software)
0 = No CLC1 interrupt event has occurred
bit 3-1 Unimplemented: Read as ‘0’
bit 0 TMR1GIF: Timer1 Gate Interrupt Flag bit
1 = The Timer1 Gate has gone inactive (the acquisition is complete)
0 = The Timer1 Gate has not gone inactive

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 161


PIC16(L)F15356/75/76/85/86

REGISTER 10-16: PIR6: PERIPHERAL INTERRUPT REQUEST REGISTER 6


U-0 U-0 U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0
— — — — — — CCP2IF CCP1IF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-2 Unimplemented: Read as ‘0’


bit 1 CCP2IF: CCP2 Interrupt Flag bit
CCPM Mode
Value
Capture Compare PWM
Capture occurred Compare match occurred Output trailing edge occurred
1
(must be cleared in software) (must be cleared in software) (must be cleared in software)
0 Capture did not occur Compare match did not occur Output trailing edge did not occur

bit 0 CCP1IF: CCP1 Interrupt Flag bit


CCPM Mode
Value
Capture Compare PWM
Capture occurred Compare match occurred Output trailing edge occurred
1
(must be cleared in software) (must be cleared in software) (must be cleared in software)
0 Capture did not occur Compare match did not occur Output trailing edge did not occur

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 162


PIC16(L)F15356/75/76/85/86

REGISTER 10-17: PIR7: PERIPHERAL INTERRUPT REQUEST REGISTER 7


U-0 U-0 R/W/HS-0/0 R/W/HS-0/0 U-0 U-0 U-0 R/W/HS-0/0
— — NVMIF NCO1IF — — — CWG1IF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware set

bit 7-6 Unimplemented: Read as ‘0’


bit 5 NVMIF: Nonvolatile Memory (NVM) Interrupt Flag bit
1 = The requested NVM operation has completed
0 = NVM interrupt not asserted
bit 4 NCO1IF: Numerically Controlled Oscillator (NCO) Interrupt Flag bit
1 = The NCO has rolled over
0 = No NCO interrupt event has occurred
bit 3-1 Unimplemented: Read as ‘0’
bit 0 CWG1IF: CWG1 Interrupt Flag bit
1 = CWG1 has gone into shutdown
0 = CWG1 is operating normally, or interrupt cleared

Note: Interrupt flag bits are set when an interrupt


condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.

 2016-2018 Microchip Technology Inc. DS40001866B-page 163


PIC16(L)F15356/75/76/85/86
TABLE 10-1: SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPTS
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE — — — — — INTEDG 147


PIE0 — — TMR0IE IOCIE — — — INTE 148
PIE1 OSFIE CSWIE — — — — — ADIE 149
PIE2 — ZCDIE — — — — C2IE C1IE 150
PIE3 RC2IE TX2IE RC1IE TX1IE BCL2IE SSP2IE BCL1IE SSP1IE 151
PIE4 — — — — — — TMR2IE TMR1IE 152
PIE5 CLC4IE CLC3IE CLC2IE CLC1IE — — — TMR1GIE 153
PIE6 — — — — — — CCP2IE CCP1IE 154
PIE7 — — NVMIE NCO1IE — — — CWG1IE 155
PIR0 — — TMR0IF IOCIF — — — INTF 156
PIR1 OSFIF CSWIF — — — — — ADIF 157
PIR2 — ZCDIF — — — — C2IF C1IF 158
PIR3 RC2IF TX2IF RC1IF TX1IF BCL2IF SSP2IF BCL1IF SSP1IF 159
PIR4 — — — — — — TMR2IF TMR1IF 160
PIR5 CLC4IF CLC3IF CLC2IF CLC1IF — — — TMR1GIF 161
PIR6 — — — — — — CCP2IF CCP1IF 162
PIR7 — — NVMIF NCO1IF — — — CWG1IF 163
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by interrupts.

 2016-2018 Microchip Technology Inc. DS40001866B-page 164


PIC16(L)F15356/75/76/85/86
11.0 POWER-SAVING OPERATION affected. The reduced execution saves power by
eliminating unnecessary operations within the CPU
MODES
and memory.
The purpose of the Power-Down modes is to reduce When the Doze Enable (DOZEN) bit is set (DOZEN =
power consumption. There are three Power-Down 1), the CPU executes only one instruction cycle out of
modes: DOZE mode, IDLE mode, and SLEEP mode. every N cycles as defined by the DOZE<2:0> bits of the
CPUDOZE register. For example, if DOZE<2:0> = 100,
11.1 DOZE Mode the instruction cycle ratio is 1:32. The CPU and
memory execute for one instruction cycle and then lay
DOZE mode saves power by reducing CPU execution
idle for 31 instruction cycles. During the unused cycles,
and program memory access, without affecting
the peripherals continue to operate at the system clock
peripheral operation. DOZE mode differs from Sleep
speed.
mode because the system oscillators continue to
operate, while only the CPU and program memory are

FIGURE 11-1: DOZE MODE OPERATION EXAMPLE


System
Clock

1 1 1 1 1 1 1 1 1 1 1 1 1

2 2 2 2 2 2 2 2 2 2 2 2 2

/ŶƐƚƌƵĐƚŝŽŶ
WĞƌŝŽĚ 3 3 3 3 3 3 3 3 3 3 3 3 3

4 4 4 4 4 4 4 4 4 4 4 4 4

1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4
CPU Clock

PFM Op’s Fetch Fetch Push 0004h Fetch Fetch

CPU Op’s Exec Exec Exec(1,2) NOP Exec Exec Exec

Interrupt
Here
(ROI = 1)
Note 1: Multi-cycle instructions are executed to completion before fetching 0004h.
2: If the pre-fetched instruction clears GIE, the ISR will not occur, but DOZEN is still cleared and the CPU will resume execution at full speed.

11.1.1 DOZE OPERATION


The Doze operation is illustrated in Figure 11-1. For
example, if ROI = 1 and DOZE<2:0> = '001', the
instruction cycle ratio is 1:4. The CPU and memory
operate for one instruction cycle and stay idle for the
next three instruction cycles.
As with normal operation, the program memory fetches
for the next instruction cycle. The system clock to the
peripherals continue throughout.

 2016-2018 Microchip Technology Inc. DS40001866B-page 165


PIC16(L)F15356/75/76/85/86
11.1.2 INTERRUPTS DURING DOZE
If an interrupt occurs during DOZE, system behavior
can be configured using the Recover-On-Interrupt
(ROI) bit and the Doze-On-Exit (DOE) bit. Refer to
Table 11-1 for details about system behavior in all
cases for a transition from Main to ISR back to Main.

TABLE 11-1: INTERRUPTS DURING DOZE


Code Flow
DOZEN ROI
Main ISR(1) Return to Main
0 0 Normal Normal operation and DOE =
operation DOZEN (in hardware) DOZEN = 0
(unchanged)
0 1 Normal Normal operation and DOE = If DOE = 1 when If DOE = 0 when
operation DOZEN (in hardware) DOZEN = 0 return from inter- return from inter-
(unchanged) rupt: rupt:
1 0 DOZE DOZE operation and DOE = DOZE operation Normal operation
operation DOZEN (in hardware) DOZEN = 1 and DOZEN = 1 and DOZEN = 0
(unchanged) (in hardware) (in hardware)
1 1 DOZE Normal operation and DOE =
operation DOZEN (in hardware) DOZEN = 0
(unchanged)
Note 1: User software can change the DOE bit in the ISR.

11.2 Sleep Mode Refer to individual chapters for more details on


peripheral operation during Sleep.
Sleep mode is entered by executing the SLEEP
instruction, while the Idle Enable (IDLEN) bit of the To minimize current consumption, the following
CPUDOZE register is clear (IDLEN = 0). If the SLEEP conditions should be considered:
instruction is executed while the IDLEN bit is set - I/O pins should not be floating
(IDLEN = 1), the CPU will enter the IDLE mode - External circuitry sinking current from I/O pins
(Section 11.2.3 “Low-Power Sleep Mode”). - Internal circuitry sourcing current from I/O
Upon entering Sleep mode, the following conditions pins
exist: - Current draw from pins with internal weak
pull-ups
1. WDT will be cleared but keeps running if - Modules using any oscillator
enabled for operation during Sleep
I/O pins that are high-impedance inputs should be
2. The PD bit of the STATUS register is cleared
pulled to VDD or VSS externally to avoid switching
3. The TO bit of the STATUS register is set currents caused by floating inputs.
4. CPU Clock and System Clock
Any module with a clock source that is not FOSC can be
5. 31 kHz LFINTOSC, HFINTOSC and SOSC are enabled. Examples of internal circuitry that might be
unaffected and peripherals using them may sourcing current include modules such as the DAC and
continue operation in Sleep. FVR modules. See Section 21.0 “5-Bit Digital-to-
6. ADC is unaffected if the dedicated FRC Analog Converter (DAC1) Module”, Section 18.0
oscillator is selected the conversion will be left “Fixed Voltage Reference (FVR)” for more informa-
abandoned if FOSC is selected and ADRES will tion on these modules.
have an incorrect value
7. I/O ports maintain the status they had before
Sleep was executed (driving high, low, or high-
impedance). This does not apply in the case of
any asynchronous peripheral which is active
and may affect the I/O port value
8. Resets other than WDT are not affected by
Sleep mode

 2016-2018 Microchip Technology Inc. DS40001866B-page 166


PIC16(L)F15356/75/76/85/86
11.2.1 WAKE-UP FROM SLEEP The WDT is cleared when the device wakes-up from
Sleep, regardless of the source of wake-up.
The device can wake-up from Sleep through one of the
following events:
11.2.2 WAKE-UP USING INTERRUPTS
1. External Reset input on MCLR pin, if enabled.
When global interrupts are disabled (GIE cleared) and
2. BOR Reset, if enabled. any interrupt source, with the exception of the clock
3. POR Reset. switch interrupt, has both its interrupt enable bit and
4. Watchdog Timer, if enabled. interrupt flag bit set, one of the following will occur:
5. Any external interrupt. • If the interrupt occurs before the execution of a
6. Interrupts by peripherals capable of running SLEEP instruction
during Sleep (see individual peripheral for more - SLEEP instruction will execute as a NOP
information). - WDT and WDT prescaler will not be cleared
The first three events will cause a device Reset. The - TO bit of the STATUS register will not be set
last three events are considered a continuation of - PD bit of the STATUS register will not be
program execution. To determine whether a device cleared
Reset or wake-up event occurred, refer to
• If the interrupt occurs during or after the
Section 8.12 “Memory Execution Violation”.
execution of a SLEEP instruction
When the SLEEP instruction is being executed, the next - SLEEP instruction will be completely
instruction (PC + 1) is prefetched. For the device to executed
wake-up through an interrupt event, the corresponding
- Device will immediately wake-up from Sleep
interrupt enable bit must be enabled. Wake-up will
occur regardless of the state of the GIE bit. If the GIE - WDT and WDT prescaler will be cleared
bit is disabled, the device continues execution at the - TO bit of the STATUS register will be set
instruction after the SLEEP instruction. If the GIE bit is - PD bit of the STATUS register will be cleared
enabled, the device executes the instruction after the Even if the flag bits were checked before executing a
SLEEP instruction, the device will then call the Interrupt SLEEP instruction, it may be possible for flag bits to
Service Routine. In cases where the execution of the become set before the SLEEP instruction completes. To
instruction following SLEEP is not desirable, the user determine whether a SLEEP instruction executed, test
should have a NOP after the SLEEP instruction.

FIGURE 11-2: WAKE-UP FROM SLEEP THROUGH INTERRUPT


Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
CLKIN(1)
CLKOUT(2) TOST(3)

Interrupt flag Interrupt Latency (4)

GIE bit
(INTCON reg.) Processor in
Sleep

Instruction Flow
PC PC PC + 1 PC + 2 PC + 2 PC + 2 0004h 0005h
Instruction Inst(PC + 1) Inst(PC + 2) Inst(0004h) Inst(0005h)
Fetched Inst(PC) = Sleep
Instruction Sleep Inst(PC + 1) Forced NOP Forced NOP
Executed Inst(PC - 1) Inst(0004h)

Note 1: External clock. High, Medium, Low mode assumed.


2: CLKOUT is shown here for timing reference.
3: TOST = 1024 TOSC. This delay does not apply to EC and INTOSC Oscillator modes.
4: GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line.

 2016-2018 Microchip Technology Inc. DS40001866B-page 167


PIC16(L)F15356/75/76/85/86
11.2.3 LOW-POWER SLEEP MODE 11.3 IDLE Mode
The PIC16F15356/75/76/85/86 device contains an When the Idle Enable (IDLEN) bit is clear (IDLEN = 0),
internal Low Dropout (LDO) voltage regulator, which the SLEEP instruction will put the device into full Sleep
allows the device I/O pins to operate at voltages up to mode (see Section 11.2 “Sleep Mode”). When IDLEN
5.5V while the internal device logic operates at a lower is set (IDLEN = 1), the SLEEP instruction will put the
voltage. The LDO and its associated reference circuitry device into IDLE mode. In IDLE mode, the CPU and
must remain active when the device is in Sleep mode. memory operations are halted, but the peripheral
The PIC16F15356/75/76/85/86 allows the user to clocks continue to run. This mode is similar to DOZE
optimize the operating current in Sleep, depending on mode, except that in IDLE both the CPU and program
the application requirements. memory are shut off.
Low-Power Sleep mode can be selected by setting the
VREGPM bit of the VREGCON register. Depending on Note: Peripherals using FOSC will continue
the configuration of these bits, the LDO and reference running while in Idle (but not in Sleep).
circuitry are placed in a low-power state when the Peripherals using HFINTOSC,
device is in Sleep. LFINTOSC, or SOSC will continue
running in both Idle and Sleep.
11.2.3.1 Sleep Current vs. Wake-up Time
In the default operating mode, the LDO and reference
circuitry remain in the normal configuration while in Note: If CLKOUT is enabled (CLKOUT = 0,
Sleep. The device is able to exit Sleep mode quickly Configuration Word 1), the output will
since all circuits remain active. In Low-Power Sleep continue operating while in Idle.
mode, when waking-up from Sleep, an extra delay time
is required for these circuits to return to the normal 11.3.1 IDLE AND INTERRUPTS
configuration and stabilize.
IDLE mode ends when an interrupt occurs (even if
The Low-Power Sleep mode is beneficial for GIE = 0), but IDLEN is not changed. The device can re-
applications that stay in Sleep mode for long periods of enter IDLE by executing the SLEEP instruction.
time. The Normal mode is beneficial for applications
If Recover-on-Interrupt is enabled (ROI = 1), the
that need to wake from Sleep quickly and frequently.
interrupt that brings the device out of Idle also restores
11.2.3.2 Peripheral Usage in Sleep full-speed CPU execution when doze is also enabled.

Some peripherals that can operate in Sleep mode will 11.3.2 IDLE AND WDT
not operate properly with the Low-Power Sleep mode
When in IDLE, the WDT Reset is blocked and will
selected. The Low-Power Sleep mode is intended for
instead wake the device. The WDT wake-up is not an
use with these peripherals:
interrupt, therefore ROI does not apply.
• Brown-out Reset (BOR)
• Watchdog Timer (WDT)
• External interrupt pin/interrupt-on-change pins Note: The WDT can bring the device out of
• Timer1 (with external clock source) IDLE, in the same way it brings the device
out of Sleep. The DOZEN bit is not
It is the responsibility of the end user to determine what
affected.
is acceptable for their application when setting the
VREGPM settings in order to ensure operation in
Sleep.

Note: The PIC16LF15356/75/76/85/86 does not


have a configurable Low-Power Sleep
mode. PIC16LF15356/75/76/85/86 is an
unregulated device and is always in the
lowest power state when in Sleep, with no
wake-up time penalty. This device has a
lower maximum VDD and I/O voltage than
the PIC16F15356/75/76/85/86. See
Section 37.0 “Electrical
Specifications” for more information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 168


PIC16(L)F15356/75/76/85/86
11.4 Register Definitions: Voltage Regulator and DOZE Control

REGISTER 11-1: VREGCON: VOLTAGE REGULATOR CONTROL REGISTER(1)


U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0 U-1
— — — — — — VREGPM —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-2 Unimplemented: Read as ‘0’


bit 1 VREGPM: Voltage Regulator Power Mode Selection bit
1 = Low-Power Sleep mode enabled in Sleep(2)
Draws lowest current in Sleep, slower wake-up
0 = Normal Power mode enabled in Sleep(2)
Draws higher current in Sleep, faster wake-up
bit 0 Unimplemented: Read as ‘1’. Maintain this bit set

Note 1: PIC16F15356/75/76/85/86 only.


2: See Section 37.0 “Electrical Specifications”.

 2016-2018 Microchip Technology Inc. DS40001866B-page 169


PIC16(L)F15356/75/76/85/86
REGISTER 11-2: CPUDOZE: DOZE AND IDLE REGISTER
R/W-0/0 R/W/HC/HS-0/0 R/W-0/0 R/W/HS/HC-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
IDLEN DOZEN(1) ROI (1)
DOE (1)
— DOZE<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other
HC = Bit is cleared by hardware Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Bit is set by hardware

bit 7 IDLEN: Idle Enable bit


1 = A SLEEP instruction places the device into IDLE mode
0 = A SLEEP instruction places the device into Sleep mode
bit 6 DOZEN: Doze Enable bit
1 = Places the device into DOZE mode
0 = Places the device into Normal mode
bit 5 ROI: Recover-on-Interrupt bit
1 = Entering the Interrupt Service Routine (ISR) makes DOZEN = 0
0 = Entering the Interrupt Service Routine (ISR) does not change DOZEN
bit 4 DOE: Doze on Exit bit
1 = Exiting the ISR makes DOZEN = 1
0 = Exiting the ISR does not change DOZEN
bit 3 Unimplemented: Read as ‘0’
bit 2-0 DOZE<2:0>: Ratio of CPU Instruction Cycles to Peripheral Instruction Cycles
111 =1:256
110 =1:128
101 =1:64
100 =1:32
011 =1:16
010 =1:8
001 =1:4
000 =1:2

Note 1: Refer to Table 11-1 for more details.

 2016-2018 Microchip Technology Inc. DS40001866B-page 170


PIC16(L)F15356/75/76/85/86
TABLE 11-2: SUMMARY OF REGISTERS ASSOCIATED WITH POWER-DOWN MODE
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
IOCEP — — — — IOCEP3 IOCEP2(1) IOCEP1(1) IOCEP0(1) 261
IOCEN — — — — IOCEN3 IOCEN2(1) IOCEN1(1) IOCEN0(1) 262
(1) (1) (1)
IOCEF — — — — IOCEF3 IOCEF2 IOCEF1 IOCEF0 262
STATUS — — — TO PD Z DC C 54
VREGCON — — — — — — VREGPM — 169
CPUDOZE IDLEN DOZEN ROI DOE — DOZE<2:0> 170
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used in Power-Down mode.
Note 1: Present only in PIC16(L)F15375/76/85/86.

 2016-2018 Microchip Technology Inc. DS40001866B-page 171


PIC16(L)F15356/75/76/85/86
12.0 WINDOWED WATCHDOG
TIMER (WWDT)
The Watchdog Timer (WDT) is a system timer that
generates a Reset if the firmware does not issue a
CLRWDT instruction within the time-out period. The
Watchdog Timer is typically used to recover the system
from unexpected events. The Windowed Watchdog
Timer (WWDT) differs in that CLRWDT instructions are
only accepted when they are performed within a
specific window during the time-out period.
The WDT has the following features:
• Selectable clock source
• Multiple operating modes
- WDT is always on
- WDT is off when in Sleep
- WDT is controlled by software
- WDT is always off
• Configurable time-out period is from 1 ms to 256
seconds (nominal)
• Configurable window size from 12.5 to 100
percent of the time-out period
• Multiple Reset conditions
• Operation during Sleep

 2016-2018 Microchip Technology Inc. DS40001866B-page 172


PIC16(L)F15356/75/76/85/86
FIGURE 12-1: WATCHDOG TIMER BLOCK DIAGRAM

Rev. 10-000162C
10/12/2016

WWDT
Armed
WDT
Window
Violation
Window Closed
Window
Comparator
CLRWDT Sizes

WDTWS

RESET

Reserved 111
Reserved 110
Reserved 101
R
Reserved 100 18-bit Prescale
Reserved 011 Counter
E
SOSC 010
MFINTOSC/16 001
LFINTOSC 000

WDTCS

WDTPS

R
5-bit Overflow
WDT Time-out
WDT Counter Latch

WDTE<1:0> = 01
SWDTEN

WDTE<1:0> = 11

WDTE<1:0> = 10
Sleep

 2016-2018 Microchip Technology Inc. DS40001866B-page 173


PIC16(L)F15356/75/76/85/86
12.1 Independent Clock Source 12.3 Time-Out Period
The WDT can derive its time base from either the 31 The WDTPS bits of the WDTCON0 register set the
kHz LFINTOSC or 31.25 kHz MFINTOSC internal time-out period from 1 ms to 256 seconds (nominal).
oscillators, or the secondary oscillator SOSC, After a Reset, the default time-out period is two
depending on the value of either the WDTCCS<2:0> seconds.
Configuration bits or the WDTCS<2:0> bits of
WDTCON1. Time intervals in this chapter are based on
a minimum nominal interval of 1 ms. See Section 37.0
“Electrical Specifications” for LFINTOSC and
MFINTOSC tolerances.

12.2 WDT Operating Modes


The Watchdog Timer module has four operating modes
controlled by the WDTE<1:0> bits in Configuration
Words. See Table 12-1.

12.2.1 WDT IS ALWAYS ON


When the WDTE bits of Configuration Words are set to
‘11’, the WDT is always on.
WDT protection is active during Sleep.

12.2.2 WDT IS OFF IN SLEEP


When the WDTE bits of Configuration Words are set to
‘10’, the WDT is on, except in Sleep.
WDT protection is not active during Sleep.

12.2.3 WDT CONTROLLED BY SOFTWARE


When the WDTE bits of Configuration Words are set to
‘01’, the WDT is controlled by the SWDTEN bit of the
WDTCON0 register.

12.2.4 WDT IS OFF


When the WDTE bits of the Configuration Word are set
to ‘00’, the WDT is always OFF.
WDT protection is unchanged by Sleep. See Table 12-1
for more details.

TABLE 12-1: WDT OPERATING MODES


Device WDT
WDTE<1:0> SWDTEN
Mode Mode

11 X X Active
Awake Active
10 X
Sleep Disabled
1 X Active
01
0 X Disabled
00 X X Disabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 174


PIC16(L)F15356/75/76/85/86
12.4 Watchdog Window • Oscillator Start-up Timer (OST) is running
• Any write to the WDTCON0 or WDTCON1 registers
The Watchdog Timer has an optional Windowed mode
that is controlled by the WDTCWS<2:0> Configuration 12.5.1 CLRWDT CONSIDERATIONS
bits and WINDOW<2:0> bits of the WDTCON1 register.
(WINDOWED MODE)
In the Windowed mode, the CLRWDT instruction must
occur within the allowed window of the WDT period. Any When in Windowed mode, the WDT must be armed
CLRWDT instruction that occurs outside of this window before a CLRWDT instruction will clear the timer. This is
will trigger a window violation and will cause a WDT performed by reading the WDTCON0 register. Execut-
Reset, similar to a WDT time out. See Figure 12-2 for an ing a CLRWDT instruction without performing such an
example. arming action will trigger a window violation.
The window size is controlled by the WDTCWS<2:0> See Table 12-2 for more information.
Configuration bits, or the WINDOW<2:0> bits of
WDTCON1, if WDTCWS<2:0> = 111. 12.6 Operation During Sleep
In the event of a window violation, a Reset will be When the device enters Sleep, the WDT is cleared. If
generated and the WDTWV bit of the PCON register the WDT is enabled during Sleep, the WDT resumes
will be cleared. This bit is set by a POR or can be set in counting. When the device exits Sleep, the WDT is
firmware. cleared again.
The WDT remains clear until the OST, if enabled, com-
12.5 Clearing the WDT pletes. See Section 9.0 “Oscillator Module (with Fail-
The WDT is cleared when any of the following Safe Clock Monitor)” for more information on the OST.
conditions occur: When a WDT time-out occurs while the device is in
• Any Reset Sleep, no Reset is generated. Instead, the device
• Valid CLRWDT instruction is executed wakes up and resumes operation. The TO and PD bits
in the STATUS register are changed to indicate the
• Device enters Sleep
event. The RWDT bit in the PCON register can also be
• Device wakes up from Sleep used. See Section 4.3.2.1 “STATUS Register” for
• WDT is disabled more information.

TABLE 12-2: WDT CLEARING CONDITIONS


Conditions WDT
WDTE<1:0> = 00
WDTE<1:0> = 01 and SWDTEN = 0
WDTE<1:0> = 10 and enter Sleep
Cleared
CLRWDT Command
Oscillator Fail Detected
Exit Sleep + System Clock = SOSC, EXTOSC, INTOSC
Change INTOSC divider (IRCF bits) Unaffected

FIGURE 12-2: WINDOW PERIOD AND DELAY

Rev. 10-000163A
8/15/2016

CLRWDT Instruction
(or other WDT Reset)
Window Period

Window Closed Window Open

Time-out Event
Window Delay
(window violation can occur)

 2016-2018 Microchip Technology Inc. DS40001866B-page 175


PIC16(L)F15356/75/76/85/86
12.7 Register Definitions: Windowed Watchdog Timer Control

REGISTER 12-1: WDTCON0: WATCHDOG TIMER CONTROL REGISTER 0


U-0 U-0 R/W(3)-q/q(2) R/W(3)-q/q(2) R/W(3)-q/q(2) R/W(3)-q/q(2) R/W(3)-q/q(2) R/W-0/0
— — (1)
WDTPS<4:0> SWDTEN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-6 Unimplemented: Read as ‘0’


bit 5-1 WDTPS<4:0>: Watchdog Timer Prescale Select bits(1)
Bit Value = Prescale Rate
11111 =Reserved. Results in minimum interval (1:32)



10011 =Reserved. Results in minimum interval (1:32)

10010 =1:8388608 (223) (Interval 256s nominal)


10001 =1:4194304 (222) (Interval 128s nominal)
10000 =1:2097152 (221) (Interval 64s nominal)
01111 =1:1048576 (220) (Interval 32s nominal)
01110 =1:524288 (219) (Interval 16s nominal)
01101 =1:262144 (218) (Interval 8s nominal)
01100 =1:131072 (217) (Interval 4s nominal)
01011 =1:65536 (Interval 2s nominal) (Reset value)
01010 =1:32768 (Interval 1s nominal)
01001 =1:16384 (Interval 512 ms nominal)
01000 =1:8192 (Interval 256 ms nominal)
00111 =1:4096 (Interval 128 ms nominal)
00110 =1:2048 (Interval 64 ms nominal)
00101 =1:1024 (Interval 32 ms nominal)
00100 =1:512 (Interval 16 ms nominal)
00011 =1:256 (Interval 8 ms nominal)
00010 =1:128 (Interval 4 ms nominal)
00001 =1:64 (Interval 2 ms nominal)
00000 =1:32 (Interval 1 ms nominal)
bit 0 SWDTEN: Software Enable/Disable for Watchdog Timer bit
If WDTE<1:0> = 1x:
This bit is ignored.
If WDTE<1:0> = 01:
1 = WDT is turned on
0 = WDT is turned off
If WDTE<1:0> = 00:
This bit is ignored.

Note 1: Times are approximate. WDT time is based on 31 kHz LFINTOSC.


2: When WDTCPS <4:0> in CONFIG3 = 11111, the Reset value of WDTPS<4:0> is 01011. Otherwise, the
Reset value of WDTPS<4:0> is equal to WDTCPS<4:0> in CONFIG3.
3: When WDTCPS <4:0> in CONFIG3 ≠ 11111, these bits are read-only.

 2016-2018 Microchip Technology Inc. DS40001866B-page 176


PIC16(L)F15356/75/76/85/86

REGISTER 12-2: WDTCON1: WATCHDOG TIMER CONTROL REGISTER 1


U-0 R/W(3)-q/q(1) R/W(3)-q/q(1) R/W(3)-q/q(1) U-0 R/W(4)-q/q(2) R/W(4)-q/q(2) R/W(4)-q/q(2)
— WDTCS<2:0> — WINDOW<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 Unimplemented: Read as ‘0’


bit 6-4 WDTCS<2:0>: Watchdog Timer Clock Select bits
111 =Reserved



010 =SOSC 32 kHz
001 =MFINTOSC 31.25 kHz
000 =LFINTOSC 31 kHz
bit 3 Unimplemented: Read as ‘0’
bit 2-0 WINDOW<2:0>: Watchdog Timer Window Select bits

Window delay Window opening


WINDOW<2:0>
Percent of time Percent of time
111 N/A 100
110 12.5 87.5
101 25 75
100 37.5 62.5
011 50 50
010 62.5 37.5
001 75 25
000 87.5 12.5

Note 1: If WDTCCS <2:0> in CONFIG3 = 111, the Reset value of WDTCS<2:0> is 000.
2: The Reset value of WINDOW<2:0> is determined by the value of WDTCWS<2:0> in the CONFIG3 register.
3: If WDTCCS<2:0> in CONFIG3 ≠ 111, these bits are read-only.
4: If WDTCWS<2:0> in CONFIG3 ≠ 111, these bits are read-only.

 2016-2018 Microchip Technology Inc. DS40001866B-page 177


PIC16(L)F15356/75/76/85/86

REGISTER 12-3: WDTPSL: WDT PRESCALE SELECT LOW BYTE REGISTER


R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0
PSCNT<7:0>(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 PSCNT<7:0>: Prescale Select Low Byte bits(1)

Note 1: The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR
registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation.

REGISTER 12-4: WDTPSH: WDT PRESCALE SELECT HIGH BYTE REGISTER


R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0
PSCNT<15:8>(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 PSCNT<15:8>: Prescale Select High Byte bits(1)

Note 1: The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR
registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation.

REGISTER 12-5: WDTTMR: WDT TIMER REGISTER


U-0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0
— WDTTMR<3:0> STATE PSCNT<17:16>(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 Unimplemented: Read as ‘0’


bit 6-3 WDTTMR<3:0>: Watchdog Timer Value bits
bit 2 STATE: WDT Armed Status bit
1 = WDT is armed
0 = WDT is not armed
bit 1-0 PSCNT<17:16>: Prescale Select Upper Byte bits(1)

Note 1: The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR
registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation.

 2016-2018 Microchip Technology Inc. DS40001866B-page 178


PIC16(L)F15356/75/76/85/86
TABLE 12-3: SUMMARY OF REGISTERS
ASSOCIATED WITH
WATCHDOG TIMER
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
OSCCON1 — NOSC<2:0> NDIV<3:0> 136
OSCCON2 — COSC<2:0> CDIV<3:0> 136
OSCCON3 CSWHOLD SOSCPWR — ORDY NOSCR — — — 137
PCON0 STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR 125
STATUS — — — TO PD Z DC C 54
WDTCON0 — — WDTPS<4:0> SWDTEN 176
WDTCON1 — WDTCS<2:0> — WINDOW<2:0> 177
WDTPSL PSCNT<7:0> 178
WDTPSH PSCNT<15:8> 178
WDTTMR — WDTTMR<4:0> STATE PSCNT<17:16> 178
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used by Watchdog Timer.

TABLE 12-4: SUMMARY OF CONFIGURATION WORD WITH WATCHDOG TIMER


Register
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0
on Page

13:8 — — FCMEN — CSWEN — — CLKOUTEN


CONFIG1 102
7:0 — RSTOSC<2:0> — FEXTOSC<2:0>
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Watchdog Timer.

 2016-2018 Microchip Technology Inc. DS40001866B-page 179


PIC16(L)F15356/75/76/85/86
13.0 NONVOLATILE MEMORY
TABLE 13-1: FLASH MEMORY
(NVM) CONTROL ORGANIZATION BY DEVICE
NVM consists of the Program Flash Memory. Total
Row Write
NVM is accessible by using both the FSR and INDF Program
Device Erase Latches
registers, or through the NVMREG register interface. Flash
(words) (words)
The write time is controlled by an on-chip timer. The (words)
write/erase voltages are generated by an on-chip PIC16(L)F15356 16K
charge pump rated to operate over the operating
voltage range of the device. PIC16(L)F15375/85 32 32 8K
NVM can be protected in two ways; by either code PIC16(L)F15376/86 16K
protection or write protection.
It is important to understand the program memory
Code protection (CP bit in Configuration Word 5)
structure for erase and programming operations. The
disables access, reading and writing, to the program
program memory is arranged in rows. A row consists of
memory via external device programmers. Code
32 14-bit program memory words. A row is the
protection does not affect the self-write and erase
minimum size that can be erased by user software.
functionality. Code protection can only be Reset by a
device programmer performing a Bulk Erase to the All or a portion of a row can be programmed. Data to be
device, clearing all nonvolatile memory, Configuration written into the program memory row is written to 14-bit
bits, and User IDs. wide data write latches. These latches are not directly
accessible, but may be loaded via sequential writes to
Write protection prohibits self-write and erase to a
the NVMDATH:NVMDATL register pair.
portion or all of the program memory, as defined by the
WRT<1:0> bits of Configuration Word 4. Write
protection does not affect a device programmer’s ability Note: To modify only a portion of a previously
to read, write, or erase the device. programmed row, the contents of the
entire row must be read. Then, the new
13.1 Program Flash Memory data and retained data can be written into
the write latches to reprogram the row of
The program memory consists of an array of 14-bit program memory. However, any
words as user memory, with additional words for User unprogrammed locations can be written
ID information, Configuration words, and interrupt without first erasing the row. In this case,
vectors. The program memory provides storage it is not necessary to save and rewrite the
locations for: other previously programmed locations
• User program instructions
• User defined data 13.1.1 PROGRAM MEMORY VOLTAGES
Program memory data can be read and/or written to The program memory is readable and writable during
through: normal operation over the full VDD range.
• CPU instruction fetch (read-only)
• FSR/INDF indirect access (read-only) 13.1.1.1 Programming Externally
(Section 13.2 “FSR and INDF Access”) The program memory cell and control logic support
• NVMREG access (Section 13.3 “NVMREG write and Bulk Erase operations down to the minimum
Access” device operating voltage. Special BOR operation is
• In-Circuit Serial Programming™ (ICSP™) enabled during Bulk Erase (Section 8.2.4 “BOR is
Read operations return a single word of memory. When always OFF”).
write and erase operations are done on a row basis, the
row size is defined in Table 13-1. Program memory will 13.1.1.2 Self-programming
erase to a logic ‘1’ and program to a logic ‘0’. The program memory cell and control logic will support
write and row erase operations across the entire VDD
range. Bulk Erase is not available when self-
programming.

 2016-2018 Microchip Technology Inc. DS40001866B-page 180


PIC16(L)F15356/75/76/85/86
13.2 FSR and INDF Access FIGURE 13-1: FLASH PROGRAM
MEMORY READ
The FSR and INDF registers allow indirect access to
FLOWCHART
the program memory.

13.2.1 FSR READ Rev. 10-000046D


8/15/2016

With the intended address loaded into an FSR register


a MOVIW instruction or read of INDF will read data from Start
the program memory. Read Operation

Reading from NVM requires one instruction cycle. The


CPU operation is suspended during the read, and
resumes immediately after. Read operations return a Select Memory:
PFM, DIA, DCI, Config Words, User
single byte of memory.
ID (NVMREGS)

13.2.2 FSR WRITE


Writing/erasing the NVM through the FSR registers (ex. Select
MOVWI instruction) is not supported in the Word Address
PIC16(L)F15356/75/76/85/86 devices. (NVMADRH:NVMADRL)

13.3 NVMREG Access


Data read now in
The NVMREG interface allows read/write access to all NVMDATH:NVMDATL
the locations accessible by FSRs, and also read/write
access to the User ID locations, and read-only access
to the device identification, revision, and Configuration
data. End
Read Operation
Writing or erasing of NVM via the NVMREG interface is
prevented when the device is write-protected.

13.3.1 NVMREG READ OPERATION


To read a NVM location using the NVMREG interface,
the user must:
1. Clear the NVMREGS bit of the NVMCON1
register if the user intends to access the
program memory locations, or set NMVREGS if
the user intends to access User ID, or
Configuration locations.
2. Write the desired address into the
NVMADRH:NVMADRL register pair (Table 13-
2).
3. Set the RD bit of the NVMCON1 register to
initiate the read.
Once the read control bit is set, the CPU operation is
suspended during the read, and resumes immediately
after. The data is available in the very next cycle, in the
NVMDATH:NVMDATL register pair; therefore, it can be
read as two bytes in the following instructions.
NVMDATH:NVMDATL register pair will hold this value
until another read or until it is written to by the user.
Upon completion, the RD bit is cleared by hardware.

 2016-2018 Microchip Technology Inc. DS40001866B-page 181


PIC16(L)F15356/75/76/85/86
EXAMPLE 13-1: PROGRAM MEMORY READ
* This code block will read 1 word of program
* memory at the memory address:
PROG_ADDR_HI : PROG_ADDR_LO
* data will be returned in the variables;
* PROG_DATA_HI, PROG_DATA_LO

BANKSELNVMADRL; Select Bank for NVMCON registers


MOVLWPROG_ADDR_LO;
MOVWFNVMADRL; Store LSB of address
MOVLWPROG_ADDR_HI;
MOVWFNVMADRH; Store MSB of address

BCF NVMCON1,NVMREGS; Do not select Configuration Space


BSF NVMCON1,RD; Initiate read

MOVFNVMDATL,W; Get LSB of word


MOVWFPROG_DATA_LO; Store in user location
MOVFNVMDATH,W; Get MSB of word
MOVWFPROG_DATA_HI; Store in user location

 2016-2018 Microchip Technology Inc. DS40001866B-page 182


PIC16(L)F15356/75/76/85/86
13.3.2 NVM UNLOCK SEQUENCE FIGURE 13-2: NVM UNLOCK
The unlock sequence is a mechanism that protects the SEQUENCE FLOWCHART
NVM from unintended self-write programming or
erasing. The sequence must be executed and
Rev. 10-000047B
8/24/2015

completed without interruption to successfully


complete any of the following operations:
Start
• Program memory Row Erase Unlock Sequence
• Load of program memory write latches
• Write of program memory write latches to pro-
gram memory
• Write of program memory write latches to User Write 0x55 to
IDs NVMCON2

The unlock sequence consists of the following steps


and must be completed in order:
• Write 55h to NVMCON2 Write 0xAA to
• Write AAh to NMVCON2 NVMCON2
• Set the WR bit of NVMCON1
Once the WR bit is set, the processor will stall internal
operations until the operation is complete and then Initiate
Write or Erase operation
resume with the next instruction. (WR = 1)

Note: The two NOP instructions after setting the


WR bit that were required in previous End
Unlock Sequence
devices are not required for
PIC16(L)F15356/75/76/85/86 devices.
See Figure 13-2.
Since the unlock sequence must not be interrupted,
global interrupts should be disabled prior to the unlock
sequence and re-enabled after the unlock sequence is
completed.

EXAMPLE 13-2: NVM UNLOCK SEQUENCE


BCF INTCON, GIE; Recommended so sequence is not interrupted
BANKSELNVMCON1;
BSF NVMCON1, WREN; Enable write/erase
MOVLW55h; Load 55h
MOVWFNVMCON2; Step 1: Load 55h into NVMCON2
MOVLWAAh; Step 2: Load W with AAh
MOVWFNVMCON2; Step 3: Load AAH into NVMCON2
BSF NVMCON1, WR; Step 4: Set WR bit to begin write/erase
BSF INTCON, GIE; Re-enable interrupts

Note 1: Sequence begins when NVMCON2 is written; steps 1-4 must occur in the cycle-accurate order shown.
2: Opcodes shown are illustrative; any instruction that has the indicated effect may be used.

 2016-2018 Microchip Technology Inc. DS40001866B-page 183


PIC16(L)F15356/75/76/85/86
13.3.3 NVMREG ERASE OF PROGRAM FIGURE 13-3: NVM ERASE
MEMORY FLOWCHART
Before writing to program memory, the word(s) to be Rev. 10-000048B
8/24/2015

written must be erased or previously unwritten. The


program memory can only be erased one row at a time.
Start
No automatic erase occurs upon the initiation of the
Erase Operation
write to program memory.
To erase a program memory row:
1. Clear the NVMREGS bit of the NVMCON1 Select Memory:
register to erase program memory locations, or PFM, Config Words, User ID
(NVMREGS)
set the NMVREGS bit to erase User ID
locations.
2. Write the desired address into the
NVMADRH:NVMADRL register pair (Table 13-2). Select Word Address
(NVMADRH:NVMADRL)
3. Set the FREE and WREN bits of the NVMCON1
register.
4. Perform the unlock sequence as described in
Section 13.3.2 “NVM Unlock Sequence”. Select Erase Operation
(FREE=1)
If the program memory address is write-protected, the
WR bit will be cleared and the erase operation will not
take place.
While erasing the program memory, CPU operation is Enable Write/Erase Operation
suspended, and resumes when the operation is (WREN=1)
complete. Upon completion, the NVMIF is set, and an
interrupt will occur if the NVMIE bit is also set.
Write latch data is not affected by erase operations, Disable Interrupts
and WREN will remain unchanged. (GIE=0)

Unlock Sequence
(See Note 1)

CPU stalls while


Erase operation completes
(2 ms typical)

Disable Write/Erase Operation


(WREN = 0)

Re-enable Interrupts
(GIE = 1)

End
Erase Operation

Note 1: See Figure 13-2.

 2016-2018 Microchip Technology Inc. DS40001866B-page 184


PIC16(L)F15356/75/76/85/86
EXAMPLE 13-3: ERASING ONE ROW OF PROGRAM FLASH MEMORY (PFM)
; This sample row erase routine assumes the following:
; 1.A valid address within the erase row is loaded in variables ADDRH:ADDRL
; 2.ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F)

BANKSEL NVMADRL
MOVF ADDRL,W
MOVWF NVMADRL ; Load lower 8 bits of erase address boundary
MOVF ADDRH,W
MOVWF NVMADRH ; Load upper 6 bits of erase address boundary
BCF NVMCON1,NVMREGS ; Choose PFM memory area
BSF NVMCON1,FREE ; Specify an erase operation
BSF NVMCON1,WREN ; Enable writes
BCF INTCON,GIE ; Disable interrupts during unlock sequence
; -------------------------------REQUIRED UNLOCK SEQUENCE:------------------------------

MOVLW 55h ; Load 55h to get ready for unlock sequence


MOVWF NVMCON2 ; First step is to load 55h into NVMCON2
MOVLW AAh ; Second step is to load AAh into W
MOVWF NVMCON2 ; Third step is to load AAh into NVMCON2
BSF NVMCON1,WR ; Final step is to set WR bit
; --------------------------------------------------------------------------------------

BSF INTCON,GIE ; Re-enable interrupts, erase is complete


BCF NVMCON1,WREN ; Disable writes

TABLE 13-2: NVM ORGANIZATION AND ACCESS INFORMATION


Master Values NVMREG Access FSR Access

Program
NVMREGS FSR
Memory Counter (PC), NVMADR< Allowed FSR
Memory Type bit Programming
Function ICSP™ 14:0> Operations Address
(NVMCON1) Address
Address
Reset Vector 0000h 0 0000h 8000h
0001h 0001h 8001h
User Memory 0
0003h 0003h 8003h
Program Flash Read
INT Vector 0004h 0 0004h 8004h Read-0nly
Memory Write
0005h 0005h 8005h
User Memory 1FFFh 0 1FFFh 9FFFh
3FFFh 3FFFh BFFFh
8000h Program Flash 0000h Read
User ID 1
8003h Memory 0003h Write
Reserved 8004h — — 0004h —
Rev ID 8005h 1 0005h
Read-Only
Device ID 8006h 1 0006h
No Access
CONFIG1 8007h 1 0007h
Program Flash
CONFIG2 8008h 1 0008h
Memory Read
CONFIG3 8009h 1 0009h
Write
CONFIG4 800Ah 1 000Ah
CONFIG5 800Bh 1 000Bh
Program Flash Read-Only
0100h-
DIA and DCI 8100h-82FFh Memory and 1 No Access
02FFh
Hard coded

 2016-2018 Microchip Technology Inc. DS40001866B-page 185


PIC16(L)F15356/75/76/85/86
13.3.4 NVMREG WRITE TO PROGRAM The following steps should be completed to load the
MEMORY write latches and program a row of program memory.
These steps are divided into two parts. First, each write
Program memory is programmed using the following
latch is loaded with data from the
steps:
NVMDATH:NVMDATL using the unlock sequence with
1. Load the address of the row to be programmed LWLO = 1. When the last word to be loaded into the
into NVMADRH:NVMADRL. write latch is ready, the LWLO bit is cleared and the
2. Load each write latch with data. unlock sequence executed. This initiates the
3. Initiate a programming operation. programming operation, writing all the latches into
Flash program memory.
4. Repeat steps 1 through 3 until all data is written.
Before writing to program memory, the word(s) to be Note: The special unlock sequence is required
written must be erased or previously unwritten. to load a write latch with data or initiate a
Program memory can only be erased one row at a time. Flash programming operation. If the
No automatic erase occurs upon the initiation of the unlock sequence is interrupted, writing to
write. the latches or program memory will not be
initiated.
Program memory can be written one or more words at
a time. The maximum number of words written at one 1. Set the WREN bit of the NVMCON1 register.
time is equal to the number of write latches. See 2. Clear the NVMREGS bit of the NVMCON1
Figure 13-4 (row writes to program memory with 32 register.
write latches) for more details. 3. Set the LWLO bit of the NVMCON1 register.
The write latches are aligned to the Flash row address When the LWLO bit of the NVMCON1 register is
boundary defined by the upper ten bits of ‘1’, the write sequence will only load the write
NVMADRH:NVMADRL, (NVMADRH<6:0>:NVMADRL<7:5>) latches and will not initiate the write to Flash
with the lower five bits of NVMADRL, (NVMADRL<4:0>) program memory.
determining the write latch being loaded. Write opera- 4. Load the NVMADRH:NVMADRL register pair
tions do not cross these boundaries. At the completion with the address of the location to be written.
of a program memory write operation, the data in the 5. Load the NVMDATH:NVMDATL register pair
write latches is reset to contain 0x3FFF. with the program memory data to be written.
6. Execute the unlock sequence (Section 13.3.2
“NVM Unlock Sequence”). The write latch is
now loaded.
7. Increment the NVMADRH:NVMADRL register
pair to point to the next location.
8. Repeat steps 5 through 7 until all but the last
write latch has been loaded.
9. Clear the LWLO bit of the NVMCON1 register.
When the LWLO bit of the NVMCON1 register is
‘0’, the write sequence will initiate the write to
Flash program memory.
10. Load the NVMDATH:NVMDATL register pair
with the program memory data to be written.
11. Execute the unlock sequence (Section 13.3.2
“NVM Unlock Sequence”). The entire program
memory latch content is now written to Flash
program memory.
Note: The program memory write latches are
reset to the blank state (0x3FFF) at the
completion of every write or erase
operation. As a result, it is not necessary
to load all the program memory write
latches. Unloaded latches will remain in
the blank state.
An example of the complete write sequence is shown in
Example 13-4. The initial address is loaded into the
NVMADRH:NVMADRL register pair; the data is loaded
using indirect addressing.

 2016-2018 Microchip Technology Inc. DS40001866B-page 186


FIGURE 13-4: NVMREGS WRITES TO PROGRAM FLASH MEMORY WITH 32 WRITE LATCHES
 2016-2018 Microchip Technology Inc.

Rev. 10-000004F

7 6 0 7 5 4 0 7 5 0 7 0 8/15/2016

NVMADRH NVMADRL - - NVMDATH NVMDATL


- r9 r8 r7 r6 r5 r4 r3 r2 r1 r0 c4 c3 c2 c1 c0 6 8

14

Program Memory Write Latches


10 5
14 14 14 14

Write Latch #0 Write Latch #1 Write Latch #30 Write Latch #31
00h 01h 1Eh 1Fh
NVMADRL<4:0>
14 14 14 14

Row Addr Addr Addr Addr

000h 0000h 0001h 001Eh 001Fh


001h 0010h 0011h 003Eh 003Fh
002h 0020h 0021h 005Eh 005Fh
NVMREGS=0

Row End
Addr End Addr
Address
NVMADRH<6:0> Decode Flash Program Memory
NVMADRL<7:5>

Configuration Memory
User ID, Device ID, Revision ID, Configuration Words, DIA, DCI
NVMREGS = 1
-page 187
PIC16(L)F15356/75/76/85/86
FIGURE 13-5: PROGRAM FLASH MEMORY WRITE FLOWCHART

Rev. 10-000049C
8/24/2015

Start
Write Operation

Determine number of
words to be written into Load the value to write
PFM. The number of TABLAT
words cannot exceed the
number of words per row
(word_cnt)

Update the word counter


Write Latches to PFM
(word_cnt--)

Select access to PFM


locations using
NVMREG<1:0> bits
Disable Interrupts
(GIE = 0)
Last word to Yes
write ?
Select Row Address
TBLPTR
No
Unlock Sequence
(See note 1)

Disable Interrupts
Select Write Operation (GIE = 0)
(FREE = 0)
CPU stalls while Write
operation completes
(2 ms typical)
Unlock Sequence
Load Write Latches Only (See note 1)

Enable Write/Erase
Operation (WREN = 1) No delay when writing to Re-enable Interrupts
PFM Latches (GIE = 1)

Disable Write/Erase
Operation (WREN = 0)

Re-enable Interrupts
(GIE = 1)

End
Write Operation

Increment Address
TBLPTR++

Note 1: See Figure 13-2.

 2016-2018 Microchip Technology Inc. DS40001866B-page 188


PIC16(L)F15356/75/76/85/86
EXAMPLE 13-4: WRITING TO PROGRAM FLASH MEMORY
; This write routine assumes the following:
; 1. 64 bytes of data are loaded, starting at the address in DATA_ADDR
; 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR,
; stored in little endian format
; 3. A valid starting address (the least significant bits = 00000) is loaded in ADDRH:ADDRL
; 4. ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F)
; 5. NVM interrupts are not taken into account

BANKSEL NVMADRH
MOVF ADDRH,W
MOVWF NVMADRH ; Load initial address
MOVF ADDRL,W
MOVWF NVMADRL
MOVLW LOW DATA_ADDR ; Load initial data address
MOVWF FSR0L
MOVLW HIGH DATA_ADDR
MOVWF FSR0H
BCF NVMCON1,NVMREGS ; Set Program Flash Memory as write location
BSF NVMCON1,WREN ; Enable writes
BSF NVMCON1,LWLO ; Load only write latches

LOOP
MOVIW FSR0++
MOVWF NVMDATL ; Load first data byte
MOVIW FSR0++
MOVWF NVMDATH ; Load second data byte
MOVF NVMADRL,W
XORLW 0x1F ; Check if lower bits of address are 00000
ANDLW 0x1F ; and if on last of 32 addresses
BTFSC STATUS,Z ; Last of 32 words?
GOTO START_WRITE ; If so, go write latches into memory
CALL UNLOCK_SEQ ; If not, go load latch
INCF NVMADRL,F ; Increment address
GOTO LOOP

START_WRITE
BCF NVMCON1,LWLO ; Latch writes complete, now write memory
CALL UNLOCK_SEQ ; Perform required unlock sequence
BCF NVMCON1,WREN ; Disable writes

UNLOCK_SEQ
MOVLW 55h
BCF INTCON,GIE ; Disable interrupts
MOVWF NVMCON2 ; Begin unlock sequence
MOVLW AAh
MOVWF NVMCON2
BSF NVMCON1,WR
BSF INTCON,GIE ; Unlock sequence complete, re-enable interrupts
return

 2016-2018 Microchip Technology Inc. DS40001866B-page 189


PIC16(L)F15356/75/76/85/86
13.3.5 MODIFYING FLASH PROGRAM FIGURE 13-6: FLASH PROGRAM
MEMORY MEMORY MODIFY
When modifying existing data in a program memory FLOWCHART
row, and data within that row must be preserved, it must Rev. 10-000050B
8/21/2015

first be read and saved in a RAM image. Program


memory is modified using the following steps:
Start
1. Load the starting address of the row to be Modify Operation
modified.
2. Read the existing data from the row into a RAM
image.
Read Operation
3. Modify the RAM image to contain the new data (See Note 1)
to be written into program memory.
4. Load the starting address of the row to be
rewritten.
An image of the entire row
5. Erase the program memory row.
read must be stored in RAM
6. Load the write latches with data from the RAM
image.
7. Initiate a programming operation.

Modify Image
The words to be modified are
changed in the RAM image

Erase Operation
(See Note 2)

Write Operation
Use RAM image
(See Note 3)

End
Modify Operation

Note 1: See Figure 13-1.


2: See Figure 13-3.
3: See Figure 13-5.

 2016-2018 Microchip Technology Inc. DS40001866B-page 190


PIC16(L)F15356/75/76/85/86
13.3.6 NVMREG ACCESS TO DEVICE
INFORMATION AREA, DEVICE
CONFIGURATION AREA, USER ID,
DEVICE ID AND CONFIGURATION
WORDS
NVMREGS can be used to access the following
memory regions:
• Device Information Area (DIA)
• Device Configuration Information (DCI)
• User ID region
• Device ID and Revision ID
• Configuration Words
The value of NVMREGS is set to ‘1’ in the NVMCON1
register to access these regions. The memory regions
listed above would be pointed to by PC<15> = 1, but
not all addresses reference valid data. Different access
may exist for reads and writes. Refer to Table 13-3.
When read access is initiated on an address outside
the parameters listed in Table 13-3, the NVMDATH:
NVMDATL register pair is cleared, reading back ‘0’s.

TABLE 13-3: NVMREGS ACCESS TO DEVICE INFORMATION AREA, DEVICE CONFIGURATION


AREA, USER ID, DEVICE ID AND CONFIGURATION WORDS (NVMREGS = 1)
Address Function Read Access Write Access
8000h-8003h User IDs Yes Yes
8005h-8006h Device ID/Revision ID Yes No
8007h-800Bh Configuration Words 1-5 Yes No
8100h-82FFh DIA and DCI Yes No

 2016-2018 Microchip Technology Inc. DS40001866B-page 191


PIC16(L)F15356/75/76/85/86
EXAMPLE 13-5: DEVICE ID ACCESS
; This write routine assumes the following:
; 1. A full row of data are loaded, starting at the address in DATA_ADDR
; 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR,
; stored in little endian format
; 3. A valid starting address (the least significant bits = 00000) is loaded in ADDRH:ADDRL
; 4. ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F)
; 5. NVM interrupts are not taken into account

BANKSEL NVMADRH
MOVF ADDRH,W
MOVWF NVMADRH ; Load initial address
MOVF ADDRL,W
MOVWF NVMADRL
MOVLW LOW DATA_ADDR ; Load initial data address
MOVWF FSR0L
MOVLW HIGH DATA_ADDR
MOVWF FSR0H
BCF NVMCON1,NVMREGS ; Set PFM as write location
BSF NVMCON1,WREN ; Enable writes
BSF NVMCON1,LWLO ; Load only write latches

LOOP
MOVIW FSR0++
MOVWF NVMDATL ; Load first data byte
MOVIW FSR0++
MOVWF NVMDATH ; Load second data byte
CALL UNLOCK_SEQ ; If not, go load latch
INCF NVMADRL,F ; Increment address
MOVF NVMADRL,W
XORLW 0x1F ; Check if lower bits of address are 00000
ANDLW 0x1F ; and if on last of 32 addresses
BTFSC STATUS,Z ; Last of 32 words?
GOTO START_WRITE ; If so, go write latches into memory
GOTO LOOP

START_WRITE
BCF NVMCON1,LWLO ; Latch writes complete, now write memory
CALL UNLOCK_SEQ ; Perform required unlock sequence
BCF NVMCON1,LWLO ; Disable writes

UNLOCK_SEQ
MOVLW 55h
BCF INTCON,GIE ; Disable interrupts
MOVWF NVMCON2 ; Begin unlock sequence
MOVLW AAh
MOVWF NVMCON2
BSF NVMCON1,WR
BSF INTCON,GIE ; Unlock sequence complete, re-enable interrupts
return

 2016-2018 Microchip Technology Inc. DS40001866B-page 192


PIC16(L)F15356/75/76/85/86
13.3.7 WRITE VERIFY
It is considered good programming practice to verify that
program memory writes agree with the intended value.
Since program memory is stored as a full row then the
stored program memory contents are compared with the
intended data stored in RAM after the last write is
complete.

FIGURE 13-7: FLASH PROGRAM


MEMORY VERIFY
FLOWCHART
Rev. 10-000051B
12/4/2015

Start
Verify Operation

This routine assumes that the last


row of data written was from an
image saved on RAM. This image
will be used to verify the data
currently stored in PFM

Read Operation(1)

NVMDAT = No
RAM image ?

Yes
Fail
Verify Operation

No Last word ?

Yes

End
Verify Operation

Note 1: See Figure 13-1.

 2016-2018 Microchip Technology Inc. DS40001866B-page 193


PIC16(L)F15356/75/76/85/86
13.3.8 WRERR BIT
The WRERR bit can be used to determine if a write
error occurred.
WRERR will be set if one of the following conditions
occurs:
• If WR is set while the NVMADRH:NMVADRL
points to a write-protected address
• A Reset occurs while a self-write operation was in
progress
• An unlock sequence was interrupted
The WRERR bit is normally set by hardware, but can
be set by the user for test purposes. Once set, WRERR
must be cleared in software.

TABLE 13-4: ACTIONS FOR PFM WHEN WR = 1


Free LWLO Actions for PFM when WR = 1 Comments
1 x Erase the 32-word row of NVMADRH:NVMADRL • If WP is enabled, WR is cleared and
location. See Section 13.3.3 “NVMREG Erase WRERR is set
of Program Memory” • All 32 words are erased
• NVMDATH:NVMDATL is ignored
0 1 Copy NVMDATH:NVMDATL to the write latch • Write protection is ignored
corresponding to NVMADR LSBs. See • No memory access occurs
Section 13.3.3 “NVMREG Erase of Program
Memory”
0 0 Write the write-latch data to PFM row. See • If WP is enabled, WR is cleared and
Section 13.3.3 “NVMREG Erase of Program WRERR is set
Memory” • Write latches are reset to 3FFh
• NVMDATH:NVMDATL is ignored

 2016-2018 Microchip Technology Inc. DS40001866B-page 194


PIC16(L)F15356/75/76/85/86
13.4 Register Definitions: Flash Program Memory Control
REGISTER 13-1: NVMDATL: NONVOLATILE MEMORY DATA LOW BYTE REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
NVMDAT<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NVMDAT<7:0>: Read/write value for Least Significant bits of program memory

REGISTER 13-2: NVMDATH: NONVOLATILE MEMORY DATA HIGH BYTE REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — NVMDAT<13:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 NVMDAT<13:8>: Read/write value for Most Significant bits of program memory

REGISTER 13-3: NVMADRL: NONVOLATILE MEMORY ADDRESS LOW BYTE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
NVMADR<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NVMADR<7:0>: Specifies the Least Significant bits for program memory address

REGISTER 13-4: NVMADRH: NONVOLATILE MEMORY ADDRESS HIGH BYTE REGISTER


U-1 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
—(1) NVMADR<14:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 Unimplemented: Read as ‘1’


bit 6-0 NVMADR<14:8>: Specifies the Most Significant bits for program memory address

Note 1: Bit is undefined while WR = 1

 2016-2018 Microchip Technology Inc. DS40001866B-page 195


PIC16(L)F15356/75/76/85/86

REGISTER 13-5: NVMCON1: NONVOLATILE MEMORY CONTROL 1 REGISTER


U-0 R/W-0/0 R/W-0/0 R/W/HC-0/0 R/W/HC-x/q R/W-0/0 R/S/HC-0/0 R/S/HC-0/0
— NVMREGS LWLO FREE WRERR(1,2,3) WREN WR(4,5,6) RD
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware

bit 7 Unimplemented: Read as ‘0’


bit 6 NVMREGS: Configuration Select bit
1 = Access DIA, DCI, Configuration, User ID and Device ID Registers
0 = Access Program Flash Memory
bit 5 LWLO: Load Write Latches Only bit
When FREE = 0:
1 = The next WR command updates the write latch for this word within the row; no memory operation is initiated.
0 = The next WR command writes data or erases
Otherwise: The bit is ignored
bit 4 FREE: Program Flash Memory Erase Enable bit
1 = Performs an erase operation with the next WR command; the 32-word pseudo-row containing the indicated
address is erased (to all 1s) to prepare for writing.
0 = All erase operations have completed normally
bit 3 WRERR: Program/Erase Error Flag bit(1,2,3)
This bit is normally set by hardware.
1 = A write operation was interrupted by a Reset, interrupted unlock sequence, or WR was written to one while
NVMADR points to a write-protected address.
0 = The program or erase operation completed normally
bit 2 WREN: Program/Erase Enable bit
1 = Allows program/erase cycles
0 = Inhibits programming/erasing of program Flash
bit 1 WR: Write Control bit(4,5,6)
When NVMREG:NVMADR points to a Program Flash Memory location:
1 = Initiates the operation indicated by Table 13-4
0 = NVM program/erase operation is complete and inactive.
bit 0 RD: Read Control bit(7)
1 = Initiates a read at address = NVMADR1, and loads data to NVMDAT Read takes one instruction cycle and the
bit is cleared when the operation is complete. The bit can only be set (not cleared) in software.
0 = NVM read operation is complete and inactive

Note 1: Bit is undefined while WR = 1.


2: Bit must be cleared by software; hardware will not clear this bit.
3: Bit may be written to ‘1’ by software in order to implement test sequences.
4: This bit can only be set by following the unlock sequence of Section 13.3.2 “NVM Unlock Sequence”.
5: Operations are self-timed, and the WR bit is cleared by hardware when complete.
6: Once a write operation is initiated, setting this bit to zero will have no effect.

 2016-2018 Microchip Technology Inc. DS40001866B-page 196


PIC16(L)F15356/75/76/85/86

REGISTER 13-6: NVMCON2: NONVOLATILE MEMORY CONTROL 2 REGISTER


W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0
NVMCON2<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NVMCON2<7:0>: Flash Memory Unlock Pattern bits


To unlock writes, a 55h must be written first followed by an AAh before setting the WR bit of the
NVMCON1 register. The value written to this register is used to unlock the writes.

TABLE 13-5: SUMMARY OF REGISTERS ASSOCIATED WITH NONVOLATILE MEMORY (NVM)


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
INTCON GIE PEIE — — — — — INTEDG 147
PIE7 — — NVMIE NCO1IE — — — CWG1IE 155
PIR7 — — NVMIF NCO1IF — — — CWG1IF 163
NVMCON1 — NVMREGS LWLO FREE WRERR WREN WR RD 196
NVMCON2 NVMCON2<7:0> 197
NVMADRL NVMADR<7:0> 195
NVMADRH —(1) NVMADR<14:8> 195
NVMDATL NVMDAT<7:0> 195
NVMDATH — — NVMDAT<13:8> 195
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by NVM.
Note 1: Unimplemented, read as ‘1’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 197


PIC16(L)F15356/75/76/85/86
14.0 I/O PORTS Disabling the input buffer prevents analog signal levels
on the pin between a logic high and low from causing
excessive current in the logic input circuitry. A
TABLE 14-1: PORT AVAILABILITY PER
simplified model of a generic I/O port, without the
DEVICE
interfaces to other peripherals, is shown in Figure 14-1.

PORTB

PORTC

PORTD

PORTE
PORTA

PORTF
Device FIGURE 14-1: GENERIC I/O PORT
OPERATION
PIC16(L)F15356 ● ● ● ● Rev. 10-000052A
7/30/2013

PIC16(L)F15375/76 ● ● ● ● ● Read LATx


PIC16(L)F15385/86 ● ● ● ● ● ●
Each port has standard registers for its operation. TRISx
These registers are:
D Q
• PORTx registers (reads the levels on the pins of
Write LATx
the device) Write PORTx VDD
CK
• LATx registers (output latch)
• TRISx registers (data direction) Data Register
• ANSELx registers (analog select) Data bus
• WPUx registers (weak pull-up) I/O pin
• INLVLx (input level control) Read PORTx

• SLRCONx registers (slew rate) To digital peripherals


• ODCONx registers (open-drain) ANSELx

Most port pins share functions with device peripherals, To analog peripherals
both analog and digital. In general, when a peripheral
VSS
is enabled on a port pin, that pin cannot be used as a
general purpose output; however, the pin can still be
read.
14.1 I/O Priorities
The Data Latch (LATx registers) is useful for read-
modify-write operations on the value that the I/O pins Each pin defaults to the PORT data latch after Reset.
are driving. Other functions are selected with the peripheral pin
select logic. See Section 15.0 “Peripheral Pin Select
A write operation to the LATx register has the same (PPS) Module” for more information.
effect as a write to the corresponding PORTx register.
A read of the LATx register reads of the values held in Analog input functions, such as ADC and comparator
the I/O PORT latches, while a read of the PORTx inputs, are not shown in the peripheral pin select lists.
register reads the actual I/O pin value. These inputs are active when the I/O pin is set for
Analog mode using the ANSELx register. Digital output
Ports that support analog inputs have an associated functions may continue to control the pin when it is in
ANSELx register. When an ANSEL bit is set, the digital Analog mode.
input buffer associated with that bit is disabled.
Analog outputs, when enabled, take priority over the
digital outputs and force the digital output driver to the
high-impedance state.

 2016-2018 Microchip Technology Inc. DS40001866B-page 198


PIC16(L)F15356/75/76/85/86
14.2 PORTA Registers 14.2.3 OPEN-DRAIN CONTROL
The ODCONA register (Register 14-6) controls the
14.2.1 DATA REGISTER open-drain feature of the port. Open-drain operation is
PORTA is an 8-bit wide, bidirectional port. The independently selected for each pin. When an
corresponding data direction register is TRISA ODCONA bit is set, the corresponding port output
(Register 14-2). Setting a TRISA bit (= 1) will make the becomes an open-drain driver capable of sinking
corresponding PORTA pin an input (i.e., disable the current only. When an ODCONA bit is cleared, the
output driver). Clearing a TRISA bit (= 0) will make the corresponding port output pin is the standard push-pull
corresponding PORTA pin an output (i.e., enables drive capable of sourcing and sinking current.
output driver and puts the contents of the output latch
on the selected pin). Example 14.2.8 shows how to
initialize PORTA. Note: It is not necessary to set open-drain
control when using the pin for I2C; the I2C
Reading the PORTA register (Register 14-1) reads the
module controls the pin and makes the pin
status of the pins, whereas writing to it will write to the
open-drain.
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then 14.2.4 SLEW RATE CONTROL
written to the PORT data latch (LATA). The SLRCONA register (Register 14-7) controls the
The PORT data latch LATA (Register 14-3) holds the slew rate option for each port pin. Slew rate control is
output port data, and contains the latest value of a independently selectable for each port pin. When an
LATA or PORTA write. SLRCONA bit is set, the corresponding port pin drive is
slew rate limited. When an SLRCONA bit is cleared,
EXAMPLE 14-1: INITIALIZING PORTA The corresponding port pin drive slews at the maximum
; This code example illustrates
rate possible.
; initializing the PORTA register. The
; other ports are initialized in the same 14.2.5 INPUT THRESHOLD CONTROL
; manner. The INLVLA register (Register 14-8) controls the input
voltage threshold for each of the available PORTA input
BANKSEL PORTA; pins. A selection between the Schmitt Trigger CMOS or
CLRF PORTA;Init PORTA
the TTL Compatible thresholds is available. The input
BANKSEL LATA;Data Latch
CLRF LATA;
threshold is important in determining the value of a read
BANKSEL ANSELA; of the PORTA register and also the level at which an
CLRF ANSELA;digital I/O interrupt-on-change occurs, if that feature is enabled.
BANKSEL TRISA; See Table 37-4 for more information on threshold
MOVLW B'00111000';Set RA<5:3> as inputs levels.
MOVWF TRISA;and set RA<2:0> as
;outputs Note: Changing the input threshold selection
should be performed while all peripheral
modules are disabled. Changing the
14.2.2 DIRECTION CONTROL threshold level during the time a module is
The TRISA register (Register 14-2) controls the active may inadvertently generate a
PORTA pin output drivers, even when they are being transition associated with an input pin,
used as analog inputs. The user should ensure the bits regardless of the actual voltage level on
in the TRISA register are maintained set when using that pin.
them as analog inputs. I/O pins configured as analog
inputs always read ‘0’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 199


PIC16(L)F15356/75/76/85/86
14.2.6 ANALOG CONTROL
The ANSELA register (Register 14-4) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELA bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELA bits has no effect on digital
output functions. A pin with its TRIS bit clear and its
ANSEL bit set will still operate as a digital output, but
the Input mode will be analog. This can cause
unexpected behavior when executing read-modify-
write instructions on the affected port.
Note: The ANSELA bits default to the Analog
mode after Reset. To use any pins as
digital general purpose or peripheral
inputs, the corresponding ANSEL bits
must be initialized to ‘0’ by user software.

14.2.7 WEAK PULL-UP CONTROL


The WPUA register (Register 14-5) controls the
individual weak pull-ups for each PORT pin.

14.2.8 PORTA FUNCTIONS AND OUTPUT


PRIORITIES
Each PORTA pin is multiplexed with other functions.
Each pin defaults to the PORT latch data after Reset.
Other output functions are selected with the peripheral
pin select logic or by enabling an analog output, such
as the DAC. See Section 15.0 “Peripheral Pin Select
(PPS) Module” for more information.
Analog input functions, such as ADC and comparator
inputs are not shown in the peripheral pin select lists.
Digital output functions may continue to control the pin
when it is in Analog mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 200


PIC16(L)F15356/75/76/85/86
14.3 Register Definitions: PORTA

REGISTER 14-1: PORTA: PORTA REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R-x/u R/W-x/u R/W-x/u R/W-x/u
RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RA<7:0>: PORTA I/O Value bits(1)


1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Writes to PORTA are actually written to corresponding LATA register. Reads from PORTA register returns
of actual I/O pin values.

REGISTER 14-2: TRISA: PORTA TRI-STATE REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TRISA<7:0>: PORTA Tri-State Control bit


1 = PORTA pin configured as an input (tri-stated)
0 = PORTA pin configured as an output

 2016-2018 Microchip Technology Inc. DS40001866B-page 201


PIC16(L)F15356/75/76/85/86

REGISTER 14-3: LATA: PORTA DATA LATCH REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-1/1 R/W-x/u R/W-x/u R/W-x/u
LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 LATA<7:0>: RA<7:0> Output Latch Value bits(1)

Note 1: Writes to PORTA are actually written to corresponding LATA register. Reads from PORTA register returns
actual I/O pin values.

REGISTER 14-4: ANSELA: PORTA ANALOG SELECT REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSA7 ANSA6 ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ANSA<7:0>: Analog Select between Analog or Digital Function on pins RA<7:0>, respectively
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
0 = Digital I/O. Pin is assigned to port or digital special function.

Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 202


PIC16(L)F15356/75/76/85/86

REGISTER 14-5: WPUA: WEAK PULL-UP PORTA REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WPUA7 WPUA6 WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 WPUA<7:0>: Weak Pull-up Register bits


1 = Pull-up enabled
0 = Pull-up disabled

Note 1: The weak pull-up device is automatically disabled if the pin is configured as an output.

REGISTER 14-6: ODCONA: PORTA OPEN-DRAIN CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ODCA7 ODCA6 ODCA5 ODCA4 ODCA3 ODCA2 ODCA1 ODCA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ODCA<7:0>: PORTA Open-Drain Enable bits


For RA<7:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

 2016-2018 Microchip Technology Inc. DS40001866B-page 203


PIC16(L)F15356/75/76/85/86

REGISTER 14-7: SLRCONA: PORTA SLEW RATE CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SLRA7 SLRA6 SLRA5 SLRA4 SLRA3 SLRA2 SLRA1 SLRA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SLRA<7:0>: PORTA Slew Rate Enable bits


For RA<7:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

REGISTER 14-8: INLVLA: PORTA INPUT LEVEL CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
INLVLA7 INLVLA6 INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 INLVLA<7:0>: PORTA Input Level Select bits


For RA<7:0> pins, respectively
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

 2016-2018 Microchip Technology Inc. DS40001866B-page 204


PIC16(L)F15356/75/76/85/86

TABLE 14-2: SUMMARY OF REGISTERS ASSOCIATED WITH PORTA


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
PORTA RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 201
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 201
LATA LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 202
ANSELA ANSA7 ANSA6 ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 202
WPUA WPUA7 WPUA6 WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0 203
ODCONA ODCA7 ODCA6 ODCA5 ODCA4 ODCA3 ODCA2 ODCA1 ODCA0 203
SLRCONA SLRA7 SLRA6 SLRA5 SLRA4 SLRA3 SLRA2 SLRA1 SLRA0 204
INLVLA INLVLA7 INLVLA6 INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0 204
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by
PORTA.

 2016-2018 Microchip Technology Inc. DS40001866B-page 205


PIC16(L)F15356/75/76/85/86
14.4 PORTB Registers 14.4.5 INPUT THRESHOLD CONTROL
The INLVLB register (Register 14-8) controls the input
14.4.1 DATA REGISTER voltage threshold for each of the available PORTB input
PORTB is an 8-bit wide, bidirectional port. The pins. A selection between the Schmitt Trigger CMOS or
corresponding data direction register is TRISB the TTL Compatible thresholds is available. The input
(Register 14-10). Setting a TRISB bit (= 1) will make threshold is important in determining the value of a read
the corresponding PORTB pin an input (i.e., disable the of the PORTB register and also the level at which an
output driver). Clearing a TRISB bit (= 0) will make the interrupt-on-change occurs, if that feature is enabled.
corresponding PORTB pin an output (i.e., enables See Table 37-4 for more information on threshold
output driver and puts the contents of the output latch levels.
on the selected pin). Figure 14-1 shows how to initialize
Note: Changing the input threshold selection
PORTB.
should be performed while all peripheral
Reading the PORTB register (Register 14-9) reads the modules are disabled. Changing the
status of the pins, whereas writing to it will write to the threshold level during the time a module is
PORT latch. All write operations are read-modify-write active may inadvertently generate a
operations. Therefore, a write to a port implies that the transition associated with an input pin,
port pins are read, this value is modified and then regardless of the actual voltage level on
written to the PORT data latch (LATB). that pin.
The PORT data latch LATB (Register 14-11) holds the
output port data, and contains the latest value of a 14.4.6 ANALOG CONTROL
LATB or PORTB write. The ANSELB register (Register 14-12) is used to
configure the Input mode of an I/O pin to analog.
14.4.2 DIRECTION CONTROL Setting the appropriate ANSELA bit high will cause all
The TRISB register (Register 14-10) controls the digital reads on the pin to be read as ‘0’ and allow
PORTB pin output drivers, even when they are being analog functions on the pin to operate correctly.
used as analog inputs. The user should ensure the bits The state of the ANSELB bits has no effect on digital
in the TRISB register are maintained set when using output functions. A pin with its TRIS bit clear and its
them as analog inputs. I/O pins configured as analog ANSEL bit set will still operate as a digital output, but
inputs always read ‘0’. the Input mode will be analog. This can cause
unexpected behavior when executing read-modify-
14.4.3 OPEN-DRAIN CONTROL write instructions on the affected port.
The ODCONB register (Register 14-14) controls the
Note: The ANSELB bits default to the Analog
open-drain feature of the port. Open-drain operation is
mode after Reset. To use any pins as
independently selected for each pin. When an
digital general purpose or peripheral
ODCONB bit is set, the corresponding port output
inputs, the corresponding ANSEL bits
becomes an open-drain driver capable of sinking
must be initialized to ‘0’ by user software.
current only. When an ODCONB bit is cleared, the
corresponding port output pin is the standard push-pull 14.4.7 WEAK PULL-UP CONTROL
drive capable of sourcing and sinking current.
The WPUB register (Register 14-5) controls the
individual weak pull-ups for each PORT pin.
Note: It is not necessary to set open-drain
control when using the pin for I2C; the I2C 14.4.8 PORTB FUNCTIONS AND OUTPUT
module controls the pin and makes the pin PRIORITIES
open-drain. Each PORTB pin is multiplexed with other functions.
Each pin defaults to the PORT latch data after Reset.
14.4.4 SLEW RATE CONTROL
Other output functions are selected with the peripheral
The SLRCONB register (Register 14-15) controls the pin select logic or by enabling an analog output, such
slew rate option for each port pin. Slew rate control is as the DAC. See Section 15.0 “Peripheral Pin Select
independently selectable for each port pin. When an (PPS) Module” for more information.
SLRCONB bit is set, the corresponding port pin drive is
Analog input functions, such as ADC and comparator
slew rate limited. When an SLRCONB bit is cleared,
inputs are not shown in the peripheral pin select lists.
The corresponding port pin drive slews at the maximum
Digital output functions may continue to control the pin
rate possible.
when it is in Analog mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 206


PIC16(L)F15356/75/76/85/86
14.5 Register Definitions: PORTB

REGISTER 14-9: PORTB: PORTB REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RB<7:0>: PORTB I/O Value bits(1)


1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Writes to PORTB are actually written to corresponding LATB register. The actual I/O pin values are read
from the PORTB register.

REGISTER 14-10: TRISB: PORTB TRI-STATE REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TRISB<7:0>: PORTB Tri-State Control bit


1 = PORTB pin configured as an input (tri-stated)
0 = PORTB pin configured as an output

 2016-2018 Microchip Technology Inc. DS40001866B-page 207


PIC16(L)F15356/75/76/85/86

REGISTER 14-11: LATB: PORTB DATA LATCH REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 LATB<7:0>: RB<7:0> Output Latch Value bits(1)

Note 1: Writes to PORTB are actually written to corresponding LATB register. Reads from PORTB register returns
actual I/O pin values.

REGISTER 14-12: ANSELB: PORTB ANALOG SELECT REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSB7 ANSB6 ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ANSB<7:0>: Analog Select between Analog or Digital Function on pins RB<7:0>, respectively
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
0 = Digital I/O. Pin is assigned to port or digital special function.

Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 208


PIC16(L)F15356/75/76/85/86

REGISTER 14-13: WPUB: WEAK PULL-UP PORTB REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 WPUB<7:0>: Weak Pull-up Register bits


1 = Pull-up enabled
0 = Pull-up disabled

REGISTER 14-14: ODCONB: PORTB OPEN-DRAIN CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ODCB7 ODCB6 ODCB5 ODCB4 ODCB3 ODCB2 ODCB1 ODCB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ODCB<7:0>: PORTB Open-Drain Enable bits


For RB<7:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

 2016-2018 Microchip Technology Inc. DS40001866B-page 209


PIC16(L)F15356/75/76/85/86

REGISTER 14-15: SLRCONB: PORTB SLEW RATE CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SLRB7 SLRB6 SLRB5 SLRB4 SLRB3 SLRB2 SLRB1 SLRB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SLRB<7:0>: PORTB Slew Rate Enable bits


For RB<7:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

REGISTER 14-16: INLVLB: PORTB INPUT LEVEL CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
INLVLB7 INLVLB6 INLVLB5 INLVLB4 INLVLB3 INLVLB2 INLVLB1 INLVLB0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 INLVLB<7:0>: PORTB Input Level Select bits


For RB<7:0> pins, respectively
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

TABLE 14-3: SUMMARY OF REGISTERS ASSOCIATED WITH PORTB


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 207
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 207
LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 208
ANSELB ANSB7 ANSB6 ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 208
WPUB WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0 209
ODCONB ODCB7 ODCB6 ODCB5 ODCB4 ODCB3 ODCB2 ODCB1 ODCB0 209
SLRCONB SLRB7 SLRB6 SLRB5 SLRB4 SLRB3 SLRB2 SLRB1 SLRB0 210
INLVLB INLVLB7 INLVLB6 INLVLB5 INLVLB4 INLVLB3 INLVLB2 INLVLB1 INLVLB0 210
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by
PORTB.

 2016-2018 Microchip Technology Inc. DS40001866B-page 210


PIC16(L)F15356/75/76/85/86
14.6 PORTC Registers 14.6.5 INPUT THRESHOLD CONTROL
The INLVLC register (Register 14-24) controls the input
14.6.1 DATA REGISTER voltage threshold for each of the available PORTC
PORTC is an 8-bit wide bidirectional port. The input pins. A selection between the Schmitt Trigger
corresponding data direction register is TRISC CMOS or the TTL Compatible thresholds is available.
(Register 14-18). Setting a TRISC bit (= 1) will make the The input threshold is important in determining the
corresponding PORTC pin an input (i.e., put the value of a read of the PORTC register and also the
corresponding output driver in a High-Impedance mode). level at which an interrupt-on-change occurs, if that
Clearing a TRISC bit (= 0) will make the corresponding feature is enabled. See Table 37-4 for more information
PORTC pin an output (i.e., enable the output driver and on threshold levels.
put the contents of the output latch on the selected pin).
Note: Changing the input threshold selection
Figure 14-1 shows how to initialize an I/O port.
should be performed while all peripheral
Reading the PORTC register (Register 14-17) reads the modules are disabled. Changing the
status of the pins, whereas writing to it will write to the threshold level during the time a module is
PORT latch. All write operations are read-modify-write active may inadvertently generate a
operations. Therefore, a write to a port implies that the transition associated with an input pin,
port pins are read, this value is modified and then written regardless of the actual voltage level on
to the PORT data latch (LATC). that pin.
The PORT data latch LATC (Register 14-19) holds the
output port data, and contains the latest value of a LATC 14.6.6 ANALOG CONTROL
or PORTC write. The ANSELC register (Register 14-20) is used to
configure the Input mode of an I/O pin to analog.
14.6.2 DIRECTION CONTROL Setting the appropriate ANSELC bit high will cause all
The TRISC register (Register 14-18) controls the digital reads on the pin to be read as ‘0’ and allow
PORTC pin output drivers, even when they are being analog functions on the pin to operate correctly.
used as analog inputs. The user should ensure the bits in The state of the ANSELC bits has no effect on digital
the TRISC register are maintained set when using them output functions. A pin with TRIS clear and ANSELC set
as analog inputs. I/O pins configured as analog inputs will still operate as a digital output, but the Input mode
always read ‘0’. will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
14.6.3 OPEN-DRAIN CONTROL affected port.
The ODCONC register (Register 14-22) controls the
Note: The ANSELC bits default to the Analog
open-drain feature of the port. Open-drain operation is
mode after Reset. To use any pins as
independently selected for each pin. When an
digital general purpose or peripheral
ODCONC bit is set, the corresponding port output
inputs, the corresponding ANSEL bits
becomes an open-drain driver capable of sinking
must be initialized to ‘0’ by user software.
current only. When an ODCONC bit is cleared, the
corresponding port output pin is the standard push-pull 14.6.7 WEAK PULL-UP CONTROL
drive capable of sourcing and sinking current.
The WPUC register (Register 14-21) controls the
individual weak pull-ups for each port pin.
Note: It is not necessary to set open-drain
14.6.8 PORTC FUNCTIONS AND OUTPUT
control when using the pin for I2C; the I2C
module controls the pin and makes the pin PRIORITIES
open-drain. Each pin defaults to the PORT latch data after Reset.
Other output functions are selected with the peripheral
14.6.4 SLEW RATE CONTROL pin select logic. See Section 15.0 “Peripheral Pin
Select (PPS) Module” for more information.
The SLRCONC register (Register 14-23) controls the
slew rate option for each port pin. Slew rate control is Analog input functions, such as ADC and comparator
independently selectable for each port pin. When an inputs, are not shown in the peripheral pin select lists.
SLRCONC bit is set, the corresponding port pin drive is Digital output functions may continue to control the pin
slew rate limited. When an SLRCONC bit is cleared, when it is in Analog mode.
The corresponding port pin drive slews at the maximum
rate possible.

 2016-2018 Microchip Technology Inc. DS40001866B-page 211


PIC16(L)F15356/75/76/85/86
14.7 Register Definitions: PORTC

REGISTER 14-17: PORTC: PORTC REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RC<7:0>: PORTC General Purpose I/O Pin bits(1)


1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Writes to PORTC are actually written to corresponding LATC register. The actual I/O pin values are read from
the PORTC register.

REGISTER 14-18: TRISC: PORTC TRI-STATE REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TRISC<7:0>: PORTC Tri-State Control bits


1 = PORTC pin configured as an input (tri-stated)
0 = PORTC pin configured as an output

REGISTER 14-19: LATC: PORTC DATA LATCH REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 LATC<7:0>: PORTC Output Latch Value bits(1)

Note 1: Writes to PORTC are actually written to corresponding LATC register. Reads from PORTC register returns
actual I/O pin values.

 2016-2018 Microchip Technology Inc. DS40001866B-page 212


PIC16(L)F15356/75/76/85/86

REGISTER 14-20: ANSELC: PORTC ANALOG SELECT REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSC7 ANSC6 ANSC5 ANSC4 ANSC3 ANSC2 ANSC1 ANSC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ANSC<7:0>: Analog Select between Analog or Digital Function on Pins RC<7:0>, respectively(1)
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
0 = Digital I/O. Pin is assigned to port or digital special function.

Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

REGISTER 14-21: WPUC: WEAK PULL-UP PORTC REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 WPUC<7:0>: Weak Pull-up Register bits


1 = Pull-up enabled
0 = Pull-up disabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 213


PIC16(L)F15356/75/76/85/86

REGISTER 14-22: ODCONC: PORTC OPEN-DRAIN CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ODCC<7:0>: PORTC Open-Drain Enable bits


For RC<7:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

REGISTER 14-23: SLRCONC: PORTC SLEW RATE CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SLRC<7:0>: PORTC Slew Rate Enable bits


For RC<7:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

REGISTER 14-24: INLVLC: PORTC INPUT LEVEL CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 INLVLC<7:0>: PORTC Input Level Select bits


For RC<7:0> pins, respectively
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

 2016-2018 Microchip Technology Inc. DS40001866B-page 214


PIC16(L)F15356/75/76/85/86

TABLE 14-4: SUMMARY OF REGISTERS ASSOCIATED WITH PORTC


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 212
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 212
LATC LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0 212
ANSELC ANSC7 ANSC6 ANSC5 ANSC4 ANSC3 ANSC2 ANSC1 ANSC0 213
WPUC WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0 213
ODCONC ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0 214
SLRCONC SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0 214
INLVLC INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 214
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTC.

 2016-2018 Microchip Technology Inc. DS40001866B-page 215


PIC16(L)F15356/75/76/85/86
14.8 PORTD Registers 14.8.5 INPUT THRESHOLD CONTROL
The INLVLD register (Register 14-24) controls the input
Note: Present only on PIC16(L)F15375/76/85/86.
voltage threshold for each of the available PORTD
input pins. A selection between the Schmitt Trigger
14.8.1 DATA REGISTER
CMOS or the TTL Compatible thresholds is available.
PORTD is an 8-bit wide, bidirectional port. The The input threshold is important in determining the
corresponding data direction register is TRISD value of a read of the PORTD register and also the
(Register 14-26). Setting a TRISD bit (= 1) will make the level at which an interrupt-on-change occurs, if that
corresponding PORTD pin an input (i.e., put the feature is enabled. See Table 37-4 for more information
corresponding output driver in a High-Impedance mode). on threshold levels.
Clearing a TRISD bit (= 0) will make the corresponding
PORTD pin an output (i.e., enable the output driver and Note: Changing the input threshold selection
put the contents of the output latch on the selected pin). should be performed while all peripheral
Figure 14-1 shows how to initialize an I/O port. modules are disabled. Changing the
threshold level during the time a module is
Reading the PORTD register (Register 14-25) reads the active may inadvertently generate a
status of the pins, whereas writing to it will write to the transition associated with an input pin,
PORT latch. All write operations are read-modify-write regardless of the actual voltage level on
operations. Therefore, a write to a port implies that the that pin.
port pins are read, this value is modified and then written
to the PORT data latch (LATD). 14.8.6 ANALOG CONTROL
The PORT data latch LATD (Register 14-27) holds the The ANSELD register (Register 14-28) is used to
output port data, and contains the latest value of a LATD configure the Input mode of an I/O pin to analog.
or PORTD write. Setting the appropriate ANSELD bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
14.8.2 DIRECTION CONTROL analog functions on the pin to operate correctly.
The TRISD register (Register 14-26) controls the The state of the ANSELD bits has no effect on digital
PORTD pin output drivers, even when they are being output functions. A pin with TRIS clear and ANSELD set
used as analog inputs. The user should ensure the bits in will still operate as a digital output, but the Input mode
the TRISD register are maintained set when using them will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
as analog inputs. I/O pins configured as analog inputs
affected port.
always read ‘0’.
Note: The ANSELD bits default to the Analog
14.8.3 OPEN-DRAIN CONTROL mode after Reset. To use any pins as
digital general purpose or peripheral
The ODCOND register (Register 14-30) controls the
inputs, the corresponding ANSEL bits
open-drain feature of the port. Open-drain operation is
must be initialized to ‘0’ by user software.
independently selected for each pin. When an
ODCOND bit is set, the corresponding port output 14.8.7 WEAK PULL-UP CONTROL
becomes an open-drain driver capable of sinking
current only. When an ODCOND bit is cleared, the The WPUD register (Register 14-29) controls the
corresponding port output pin is the standard push-pull individual weak pull-ups for each port pin.
drive capable of sourcing and sinking current.
14.8.8 PORTD FUNCTIONS AND OUTPUT
PRIORITIES
Note: It is not necessary to set open-drain Each pin defaults to the PORT latch data after Reset.
control when using the pin for I2C; the I2C Other output functions are selected with the peripheral
module controls the pin and makes the pin pin select logic. See Section 15.0 “Peripheral Pin
open-drain. Select (PPS) Module” for more information.
Analog input functions, such as ADC and comparator
14.8.4 SLEW RATE CONTROL inputs, are not shown in the peripheral pin select lists.
The SLRCOND register (Register 14-31) controls the Digital output functions may continue to control the pin
slew rate option for each port pin. Slew rate control is when it is in Analog mode.
independently selectable for each port pin. When an
SLRCOND bit is set, the corresponding port pin drive is
slew rate limited. When an SLRCOND bit is cleared,
The corresponding port pin drive slews at the maximum
rate possible.

 2016-2018 Microchip Technology Inc. DS40001866B-page 216


PIC16(L)F15356/75/76/85/86
14.9 Register Definitions: PORTD

REGISTER 14-25: PORTD: PORTD REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RD<7:0>: PORTD General Purpose I/O Pin bits(1)


1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Writes to PORTD are actually written to corresponding LATD register. Reads from PORTD register is
return of actual I/O pin values.

REGISTER 14-26: TRISD: PORTD TRI-STATE REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TRISD<7:0>: PORTD Tri-State Control bits


1 = PORTD pin configured as an input (tri-stated)
0 = PORTD pin configured as an output

REGISTER 14-27: LATD: PORTD DATA LATCH REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 LATD<7:0>: PORTD Output Latch Value bits(1)

Note 1: Writes to PORTD are actually written to corresponding LATD register. Reads from PORTD register is
return of actual I/O pin values.

 2016-2018 Microchip Technology Inc. DS40001866B-page 217


PIC16(L)F15356/75/76/85/86

REGISTER 14-28: ANSELD: PORTD ANALOG SELECT REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ANSD<7:0>: Analog Select between Analog or Digital Function on Pins RD<7:0>, respectively(1)
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.

Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

REGISTER 14-29: WPUD: WEAK PULL-UP PORTD REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WPUD7 WPUD6 WPUD5 WPUD4 WPUD3 WPUD2 WPUD1 WPUD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 WPUD<7:0>: Weak Pull-up Register bits(1)


1 = Pull-up enabled
0 = Pull-up disabled

Note 1: The weak pull-up device is automatically disabled if the pin is configured as an output.

 2016-2018 Microchip Technology Inc. DS40001866B-page 218


PIC16(L)F15356/75/76/85/86

REGISTER 14-30: ODCOND: PORTD OPEN-DRAIN CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ODCD7 ODCD6 ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ODCD<7:0>: PORTD Open-Drain Enable bits


For RD<7:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

REGISTER 14-31: SLRCOND: PORTD SLEW RATE CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SLRD7 SLRD6 SLRD5 SLRD4 SLRD3 SLRD2 SLRD1 SLRD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SLRD<7:0>: PORTD Slew Rate Enable bits


For RD<7:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

REGISTER 14-32: INLVLD: PORTD INPUT LEVEL CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
INLVLD7 INLVLD6 INLVLD5 INLVLD4 INLVLD3 INLVLD2 INLVLD1 INLVLD0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 INLVLD<7:0>: PORTD Input Level Select bits


For RD<7:0> pins, respectively
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

 2016-2018 Microchip Technology Inc. DS40001866B-page 219


PIC16(L)F15356/75/76/85/86

TABLE 14-5: SUMMARY OF REGISTERS ASSOCIATED WITH PORTD


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
PORTD RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 217
TRISD TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 217
LATD LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 217
ANSELD ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 218
WPUD WPUD7 WPUD6 WPUD5 WPUD4 WPUD3 WPUD2 WPUD1 WPUD0 218
ODCOND ODCD7 ODCD6 ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0 219
SLRCOND SLRD7 SLRD6 SLRD5 SLRD4 SLRD3 SLRD2 SLRD1 SLRD0 219
INLVLD INLVLD7 INLVLD6 INLVLD5 INLVLD4 INLVLD3 INLVLD2 INLVLD1 INLVLD0 219
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTD.

 2016-2018 Microchip Technology Inc. DS40001866B-page 220


PIC16(L)F15356/75/76/85/86
14.10 PORTE Registers will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
14.10.1 DATA REGISTER affected port.
PORTE is a 4-bit wide port. The corresponding data Note: The ANSELE bits default to the Analog
direction register is TRISE (Register 14-33). Setting a mode after Reset. To use any pins as
TRISE bit (= 1) will make the corresponding PORTE digital general purpose or peripheral
pin an input (i.e., disable the output driver). Clearing a inputs, the corresponding ANSEL bits
TRISE bit (= 0) will make the corresponding PORTE must be initialized to ‘0’ by user software.
pin an output (i.e., enables output driver and puts the
contents of the output latch on the selected pin). 14.10.5 WEAK PULL-UP CONTROL
Figure 14-1 shows how to initialize PORTE. The WPUE register (Register 14-37) controls the
Reading the PORTE register (Register 14-33) reads individual weak pull-ups for each port pin.
the status of the pins, whereas writing to it will write to
the PORT latch. All write operations are read-modify-
write operations. Therefore, a write to a port implies
that the port pins are read, this value is modified and
then written to the PORT data latch (LATE).

14.10.2 DIRECTION CONTROL


The TRISE register (Register 14-34) controls the
PORTE pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits in
the TRISE register are maintained set when using them
as analog inputs. I/O pins configured as analog inputs
always read ‘0’.
Note: The TRISE3 bit is a read-only bit and it
always reads a ‘1’.

14.10.3 INPUT THRESHOLD CONTROL


The INLVLE register (Register 14-40) controls the input
voltage threshold for each of the available PORTE
input pins. A selection between the Schmitt Trigger
CMOS or the TTL Compatible thresholds is available.
The input threshold is important in determining the
value of a read of the PORTE register and also the level
at which an interrupt-on-change occurs, if that feature
is enabled. See Table 37-4 for more information on
threshold levels.
Note: Changing the input threshold selection
should be performed while all peripheral
modules are disabled. Changing the
threshold level during the time a module is
active may inadvertently generate a
transition associated with an input pin,
regardless of the actual voltage level on
that pin.

14.10.4 ANALOG CONTROL


The ANSELE register (Register 14-36) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELE bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELE bits has no effect on digital
output functions. A pin with TRIS clear and ANSELE set
will still operate as a digital output, but the Input mode

 2016-2018 Microchip Technology Inc. DS40001866B-page 221


PIC16(L)F15356/75/76/85/86
14.10.6 PORTE FUNCTIONS AND OUTPUT
PRIORITIES
Each pin defaults to the PORT latch data after Reset.
Other output functions are selected with the peripheral
pin select logic. See Section 15.0 “Peripheral Pin
Select (PPS) Module” for more information.
Analog input functions, such as ADC and comparator
inputs, are not shown in the peripheral pin select lists.
Digital output functions may continue to control the pin
when it is in Analog mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 222


PIC16(L)F15356/75/76/85/86
14.11 Register Definitions: PORTE

REGISTER 14-33: PORTE: PORTE REGISTER


U-0 U-0 U-0 U-0 R-x/u R-x/u R-x/u R-x/u
— — — — RE3 RE2(1) RE1 (1)
RE0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 RE<3:0>: PORTE Input Pin bits
1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Present on PIC16(L)F15375/76/85/86 only.

REGISTER 14-34: TRISE: PORTE TRI-STATE REGISTER


U-0 U-0 U-0 U-0 U-1 R/W-1/1 R/W-1/1 R/W-1/1
— — — — —(2) TRISE2(1) TRISE1(1) TRISE0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3 Unimplemented: Read as ‘1’
bit 2-0 Unimplemented: Read as ‘0’
bit 2-0 TRISA<2:0>: PORTA Tri-State Control bit(1)
1 = PORTA pin configured as an input (tri-stated)
0 = PORTA pin configured as an output

Note 1: Present on PIC16(L)F15375/76/85/86 only.


2: Unimplemented, read as ‘1’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 223


PIC16(L)F15356/75/76/85/86

REGISTER 14-35: LATE: PORTE DATA LATCH REGISTER(1)


U-0 U-0 U-0 U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1
— — — — — LATE2 LATE1 LATE0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 LATE<2:0>: PORTE Output Latch Value bits

Note 1: Present on PIC16(L)F15375/76/85/86 only.


2: Writes to PORTE are actually written to corresponding LATE register. Reads from PORTE register is
return of actual I/O pin values.

REGISTER 14-36: ANSELE: PORTE ANALOG SELECT REGISTER(1)


U-0 U-0 U-0 U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1
— — — — — ANSE2 ANSE1 ANSE0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 ANSE<2:0>: Analog Select between Analog or Digital Function on Pins RE<2:0>, respectively(2)
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(2). Digital input buffer disabled.

Note 1: Present on PIC16(L)F15375/76/85/86 only.


2: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 224


PIC16(L)F15356/75/76/85/86

REGISTER 14-37: WPUE: WEAK PULL-UP PORTE REGISTER


U-0 U-0 U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
(2) (1) (1)
— — — — WPUE3 WPUE2 WPUE1 WPUE0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 WPUE<3:0>: Weak Pull-up Register bits
1 = Pull-up enabled
0 = Pull-up disabled

Note 1: Present on PIC16(L)F15375/76/85/86 only.


2: If MCLRE = 1, the weak pull-up in RE3 is always enabled; bit WPUE3 is not affected.
3: The weak pull-up device is automatically disabled if the pin is configured as an output.
REGISTER 14-38: ODCONE: PORTE OPEN-DRAIN CONTROL REGISTER(1)
U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — — ODCE2 ODCE1 ODCE0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 ODCE<3:0>: PORTE Open-Drain Enable bits
For RE<3:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

Note 1: Present on PIC16(L)F15375/76/85/86 only.

REGISTER 14-39: SLRCONE: PORTE SLEW RATE CONTROL REGISTER(1)


U-0 U-0 U-0 U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1
— — — — — SLRE2 SLRE1 SLRE0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 225


PIC16(L)F15356/75/76/85/86
REGISTER 14-39: SLRCONE: PORTE SLEW RATE CONTROL REGISTER(1) (CONTINUED)
bit 2-0 SLRE<2:0>: PORTE Slew Rate Enable bits
For RE<2:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

Note 1: Present on PIC16(L)F15375/76/85/86 only.


REGISTER 14-40: INLVLE: PORTE INPUT LEVEL CONTROL REGISTER
U-0 U-0 U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
— — — — INLVLE3 INLVLE2(1) INLVLE1 (1)
INLVLE0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 INLVLE<3:0>: PORTE Input Level Select bits
For RE<3:0> pins,
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

Note 1: Present on PIC16(L)F15375/76/85/86 only.

 2016-2018 Microchip Technology Inc. DS40001866B-page 226


PIC16(L)F15356/75/76/85/86

TABLE 14-6: SUMMARY OF REGISTERS ASSOCIATED WITH PORTE


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

PORTE — — — — RE3 RE2(1) RE1(1) RE0(1) 223


TRISE — — — — —(2) TRISE2(1) TRISE2(1) TRISE2(1) 223
LATE(1) — — — — — LATE2 LATE2 LATE2 224
(1)
ANSELE — — — — — ANSE2 ANSE1 ANSE0 218
WPUE — — — — WPUE3 WPUE2(1) WPUE1(1) WPUE0(1) 225
ODCONE(1) — — — — — ODCE2 ODCE1 ODCE0 225
(1) (1) (1) (1)
SLRCONE — — — — — SLRE2 SLRE1 SLRE0 225
INLVLE — — — — INLVLE3 INLVLE2(1) INLVLE1(1) INLVLE0(1) 226
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTE.
Note 1: Present only in PIC16(L)F15375/76/85/86.
2: Unimplemented, read as ‘1’

TABLE 14-7: SUMMARY OF CONFIGURATION WORD WITH PORTE


Register
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0
on Page

13:8 — — DEBUG STVREN PPS1WAY ZCDDIS BORV —


CONFIG2 103
7:0 BOREN <1:0> LPBOREN — — — PWRTE MCLRE
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by PORTE.

 2016-2018 Microchip Technology Inc. DS40001866B-page 227


PIC16(L)F15356/75/76/85/86
14.12 PORTF Registers 14.12.4 OPEN-DRAIN CONTROL
The ODCONF register (Register 14-46) controls the
Note: Present only on PIC16(L)F15385/86.
open-drain feature of the port. Open-drain operation is
independently selected for each pin. When an
14.12.1 DATA REGISTER
ODCONF bit is set, the corresponding port output
PORTF is an 8-bit wide, bidirectional port. The becomes an open-drain driver capable of sinking
corresponding data direction register is TRISF current only. When an ODCONF bit is cleared, the
(Register 14-42). Setting a TRISF bit (= 1) will make the corresponding port output pin is the standard push-pull
corresponding PORTF pin an input (i.e., put the drive capable of sourcing and sinking current.
corresponding output driver in a High-Impedance mode).
Clearing a TRISF bit (= 0) will make the corresponding
PORTF pin an output (i.e., enable the output driver and Note: It is not necessary to set open-drain
put the contents of the output latch on the selected pin). control when using the pin for I2C; the I2C
Figure 14-1 shows how to initialize an I/O port. module controls the pin and makes the pin
Reading the PORTF register (Register 14-41) reads the open-drain.
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write 14.12.5 SLEW RATE CONTROL
operations. Therefore, a write to a port implies that the The SLRCONF register (Register 14-47) controls the
port pins are read, this value is modified and then written slew rate option for each port pin. Slew rate control is
to the PORT data latch (LATF). independently selectable for each port pin. When an
The PORT data latch LATF (Register 14-43) holds the SLRCONF bit is set, the corresponding port pin drive is
output port data, and contains the latest value of a LATF slew rate limited. When an SLRCONF bit is cleared,
or PORTF write. The corresponding port pin drive slews at the maximum
rate possible.
14.12.2 DIRECTION CONTROL
14.12.6 ANALOG CONTROL
The TRISF register (Register 14-42) controls the
PORTF pin output drivers, even when they are being The ANSELF register (Register 14-44) is used to
used as analog inputs. The user should ensure the bits in configure the Input mode of an I/O pin to analog.
the TRISF register are maintained set when using them Setting the appropriate ANSELF bit high will cause all
as analog inputs. I/O pins configured as analog inputs digital reads on the pin to be read as ‘0’ and allow
always read ‘0’. analog functions on the pin to operate correctly.
The state of the ANSELF bits has no effect on digital
14.12.3 INPUT THRESHOLD CONTROL output functions. A pin with TRIS clear and ANSELF set
The INLVLF register (Register 14-48) controls the input will still operate as a digital output, but the Input mode
voltage threshold for each of the available PORTF will be analog. This can cause unexpected behavior
input pins. A selection between the Schmitt Trigger when executing read-modify-write instructions on the
CMOS or the TTL Compatible thresholds is available. affected port.
The input threshold is important in determining the Note: The ANSELF bits default to the Analog
value of a read of the PORTF register and also the level mode after Reset. To use any pins as
at which an interrupt-on-change occurs, if that feature digital general purpose or peripheral
is enabled. See Table 37-4 for more information on inputs, the corresponding ANSEL bits
threshold levels. must be initialized to ‘0’ by user software.
Note: Changing the input threshold selection
should be performed while all peripheral 14.12.7 WEAK PULL-UP CONTROL
modules are disabled. Changing the The WPUF register (Register 14-45) controls the
threshold level during the time a module is individual weak pull-ups for each port pin.
active may inadvertently generate a
transition associated with an input pin, 14.12.8 PORTF FUNCTIONS AND OUTPUT
regardless of the actual voltage level on PRIORITIES
that pin. Each pin defaults to the PORT latch data after Reset.
Other output functions are selected with the peripheral
pin select logic. See Section 15.0 “Peripheral Pin
Select (PPS) Module” for more information.
Analog input functions, such as ADC and comparator
inputs, are not shown in the peripheral pin select lists.
Digital output functions may continue to control the pin
when it is in Analog mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 228


PIC16(L)F15356/75/76/85/86
14.13 Register Definitions: PORTF

REGISTER 14-41: PORTF: PORTF REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RF<7:0>: PORTF General Purpose I/O Pin bits(1)


1 = Port pin is > VIH
0 = Port pin is < VIL

Note 1: Writes to PORTF are actually written to corresponding LATF register. Reads from PORTF register is return
of actual I/O pin values.

REGISTER 14-42: TRISF: PORTF TRI-STATE REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISF7 TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TRISF<7:0>: PORTF Tri-State Control bits


1 = PORTF pin configured as an input (tri-stated)
0 = PORTF pin configured as an output

REGISTER 14-43: LATF: PORTF DATA LATCH REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATF7 LATF6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 LATF<7:0>: PORTF Output Latch Value bits(1)

Note 1: Writes to PORTF are actually written to corresponding LATF register. Reads from PORTF register is return
of actual I/O pin values.

 2016-2018 Microchip Technology Inc. DS40001866B-page 229


PIC16(L)F15356/75/76/85/86

REGISTER 14-44: ANSELF: PORTF ANALOG SELECT REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSF7 ANSF6 ANSF5 ANSF4 ANSF3 ANSF2 ANSF1 ANSF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ANSF<7:0>: Analog Select between Analog or Digital Function on Pins RF<7:0>, respectively(1)
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.

Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.

REGISTER 14-45: WPUF: WEAK PULL-UP PORTF REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WPUF7 WPUF6 WPUF5 WPUF4 WPUF3 WPUF2 WPUF1 WPUF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 WPUF<7:0>: Weak Pull-up Register bits(1)


1 = Pull-up enabled
0 = Pull-up disabled

Note 1: The weak pull-up device is automatically disabled if the pin is configured as an output.

 2016-2018 Microchip Technology Inc. DS40001866B-page 230


PIC16(L)F15356/75/76/85/86

REGISTER 14-46: ODCONF: PORTF OPEN-DRAIN CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ODCF7 ODCF6 ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ODCF<7:0>: PORTF Open-Drain Enable bits


For RF<7:0> pins, respectively
1 = Port pin operates as open-drain drive (sink current only)
0 = Port pin operates as standard push-pull drive (source and sink current)

REGISTER 14-47: SLRCONF: PORTF SLEW RATE CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SLRF7 SLRF6 SLRF5 SLRF4 SLRF3 SLRF2 SLRF1 SLRF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SLRF<7:0>: PORTF Slew Rate Enable bits


For RF<7:0> pins, respectively
1 = Port pin slew rate is limited
0 = Port pin slews at maximum rate

REGISTER 14-48: INLVLF: PORTF INPUT LEVEL CONTROL REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
INLVLF7 INLVLF6 INLVLF5 INLVLF4 INLVLF3 INLVLF2 INLVLF1 INLVLF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 INLVLF<7:0>: PORTF Input Level Select bits


For RF<7:0> pins, respectively
1 = ST input used for PORT reads and interrupt-on-change
0 = TTL input used for PORT reads and interrupt-on-change

 2016-2018 Microchip Technology Inc. DS40001866B-page 231


PIC16(L)F15356/75/76/85/86

TABLE 14-8: SUMMARY OF REGISTERS ASSOCIATED WITH PORTF


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
PORTF RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0 217
TRISF TRISF7 TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0 217
LATF LATF7 LATF6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0 217
ANSELF ANSF7 ANSF6 ANSF5 ANSF4 ANSF3 ANSF2 ANSF1 ANSF0 218
WPUF WPUF7 WPUF6 WPUF5 WPUF4 WPUF3 WPUF2 WPUF1 WPUF0 218
ODCONF ODCF7 ODCF6 ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCF0 219
SLRCONF SLRF7 SLRF6 SLRF5 SLRF4 SLRF3 SLRF2 SLRF1 SLRF0 219
INLVLF INLVLF7 INLVLF6 INLVLF5 INLVLF4 INLVLF3 INLVLF2 INLVLF1 INLVLF0 219
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTF.

 2016-2018 Microchip Technology Inc. DS40001866B-page 232


PIC16(L)F15356/75/76/85/86
15.0 PERIPHERAL PIN SELECT
(PPS) MODULE
The Peripheral Pin Select (PPS) module connects
peripheral inputs and outputs to the device I/O pins.
Only digital signals are included in the selections.
All analog inputs and outputs remain fixed to their
assigned pins. Input and output selections are
independent as shown in the simplified block diagram
Figure 15-1.

FIGURE 15-1: SIMPLIFIED PPS BLOCK DIAGRAM

PPS Outputs
RA0PPS
PPS Inputs

abcPPS RA0
RA0
Peripheral abc

RxyPPS

Rxy

Peripheral xyz
RE3(1) RE3PPS(1)

xyzPPS RE3(1)

Note 1: RE3 is PPS input capable only (when MLCR is disabled).

15.1 PPS Inputs 15.2 PPS Outputs


Each peripheral has a PPS register with which the Each I/O pin has a PPS register with which the pin
inputs to the peripheral are selected. Inputs include the output source is selected. With few exceptions, the port
device pins. TRIS control associated with that pin retains control
Although every peripheral has its own PPS input over the pin output driver. Peripherals that control the
selection register, the selections are identical for every pin output driver as part of the peripheral operation will
peripheral as shown in Register 15-1. override the TRIS control as needed. These
peripherals are (See Section 15.3 “Bidirectional
Note: The notation “xxx” in the register name is Pins”):
a place holder for the peripheral identifier.
• EUSART (synchronous operation)
For example, CLC1PPS.
• MSSP (I2C)
Although every pin has its own PPS peripheral
selection register, the selections are identical for every
pin as shown in Register 15-2.
Note: The notation “Rxy” is a place holder for the
pin port and bit identifiers. For example, x
and y for PORTA bit 0 would be A and 0,
respectively, resulting in the pin PPS
output selection register RA0PPS.

 2016-2018 Microchip Technology Inc. DS40001866B-page 233


PIC16(L)F15356/75/76/85/86
TABLE 15-1: PPS INPUT SIGNAL ROUTING OPTIONS (PIC16(L)F15356)
Default Remappable to Pins of PORTx
INPUT SIGNAL Input Register Reset Value
Location at PIC16(L)F15356
NAME Name (xxxPPS<5:0>)
POR
PORTA PORTB PORTC
INT INTPPS RB0 01000  
T0CKI T0CKIPPS RA4 00100  
T1CKI T1CKIPSS RC0 10000  
T1G T1GPPS RB5 01101  
T2IN T2INPPS RC3 10011  
CCP1 CCP1PPS RC2 10010  
CCP2 CCP2PPS RC1 10001  
CWG1IN CWG1PPS RB0 01000  
CLCIN0 CLCIN0PPS RA0 00000  
CLCIN1 CLCIN1PPS RA1 00001  
CLCIN2 CLCIN2PPS RB6 01110  
CLCIN3 CLCIN3PPS RB7 01111  
ADACT ADACTPPS RB4 01100  
SCK1/SCL1 SSP1CLKPPS RC3 10011  
SDI1/SDA1 SSP1DATPPS RC4 10100  
SS1 SSP1SS1PPS RA5 00101  
SCK2/SCL2 SSP2CLKPPS RB1 01001  
SDI2/SDA2 SSP2DATPPS RB2 01010  
SS2 SSP2SSPPS RB0 01000  
RX1/DT1 RX1DTPPS RC7 10111  
CK1 TX1CKPPS RC6 10110  
RX2/DT2 RX2DTPPS RB7 01111  
CK2 TX2CKPPS RB6 01110  

 2016-2018 Microchip Technology Inc. DS40001866B-page 234


PIC16(L)F15356/75/76/85/86
TABLE 15-2: PPS INPUT SIGNAL ROUTING OPTIONS (PIC16(L)F15375/76)
Default Remappable to Pins of PORTx
INPUT SIGNAL Input Register Reset Value
Location at PIC16(L)F15375/76
NAME Name (xxxPPS<4:0>)
POR
PORTA PORTB PORTC PORTD
INT INTPPS RB0 01000  
T0CKI T0CKIPPS RA4 00100  
T1CKI T1CKIPSS RC0 10000  
T1G T1GPPS RB5 01101  
T2IN T2INPPS RC3 10011  
CCP1 CCP1PPS RC2 10010  
CCP2 CCP2PPS RC1 10001  
CWG1IN CWG1INPPS RB0 01000  
CLCIN0 CLCIN0PPS RA0 00000  
CLCIN1 CLCIN1PPS RA1 00001  
CLCIN2 CLCIN2PPS RB6 01110  
CLCIN3 CLCIN3PPS RB7 01111  
ADACT ADACTPPS RB4 01100  
SCK1/SCL1 SSP1CLKPPS RC3 10011  
SDI1/SDA1 SSP1DATPPS RC4 10100  
SS1 SSP1SS1PPS RA5 00101  
SCK2/SCL2 SSP2CLKPPS RB1 01001  
SDI2/SDA2 SSP2DATPPS RB2 01010  
SS2 SSP2SSPPS RB0 01000  
RX1/DT1 RX1DTPPS RC7 10111  
CK1 TX1CKPPS RC6 10110  
RX2/DT2 RX2DTPPS RB7 01111  
CK2 TX2CKPPS RB6 01110  

 2016-2018 Microchip Technology Inc. DS40001866B-page 235


PIC16(L)F15356/75/76/85/86
TABLE 15-3: PPS INPUT SIGNAL ROUTING OPTIONS (PIC16(L)F15385/86)
Default Remappable to Pins of PORTx
INPUT SIGNAL Input Register Reset Value
Location at PIC16(L)F15385/86
NAME Name (xxxPPS<4:0>)
POR
PORTA PORTB PORTC PORTD PORTF
INT INTPPS RB0 01000  
T0CKI T0CKIPPS RA4 00100   
T1CKI T1CKIPSS RC0 10000  
T1G T1GPPS RB5 01101  
T2IN T2INPPS RC3 10011  
CCP1 CCP1PPS RC2 10010   
CCP2 CCP2PPS RC1 10001   
CWG1IN CWG1INPPS RB0 01000  
CLCIN0 CLCIN0PPS RA0 00000  
CLCIN1 CLCIN1PPS RA1 00001  
CLCIN2 CLCIN2PPS RB6 01110  
CLCIN3 CLCIN3PPS RB7 01111  
ADACT ADACTPPS RB4 01100  
SCK1/SCL1 SSP1CLKPPS RC3 10011  
SDI1/SDA1 SSP1DATPPS RC4 10100  
SS1 SSP1SS1PPS RA5 00101  
SCK2/SCL2 SSP2CLKPPS RB1 01001  
SDI2/SDA2 SSP2DATPPS RB2 01010  
SS2 SSP2SSPPS RB0 01000  
RX1/DT1 RX1PPS RC7 10111   
CK1 TX1PPS RC6 10110   
RX2/DT2 RX2PPS RB7 01111  
CK2 TX2PPS RB6 01110  

 2016-2018 Microchip Technology Inc. DS40001866B-page 236


PIC16(L)F15356/75/76/85/86
TABLE 15-4: PPS INPUT REGISTER
TABLE 15-4: PPS INPUT REGISTER VALUES
VALUES Desired Input Pin Value to Write to Register
Desired Input Pin Value to Write to Register RF0 (3)
0x28
RA0 0x00 RF1(3) 0x29
RA1 0x01 RF2(3) 0x2A
RA2 0x02 RF3(3) 0x2B
RA3 0x03 RF4(3) 0x2C
RA4 0x04 RF5(3) 0x2D
RA5 0x05 RF6(3) 0x2E
RA6 0x06 RF7(3) 0x2F
RA7 0x07 Note 1: Only a few of the values in this column are
RB0 0x08 valid for any given signal. For example,
RB1 0x09 since the INT signal can only be mapped
to PORTA or PORTB pins, only the regis-
RB2 0x0A ter values 0x00-0x0F (corresponding to
RB3 0x0B RA<7:0> and RB<7:0>) are valid values
RB4 0x0C to write to the INTPPS register.
RB5 0x0D 2: Present on PIC16(L)F15375/76/85/86 only.
RB6 0x0E 3: Present on PIC16(L)F15385/86 only.
RB7 0x0F
RC0 0x10
RC1 0x11
RC2 0x12
RC3 0x13
RC4 0x14
RC5 0x15
RC6 0x16
RC7 0x17
RD0(2) 0x18
RD1(2) 0x19
RD2(2) 0x1A
RD3(2) 0x1B
RD4(2) 0x1C
RD5(2) 0x1D
RD6(2) 0x1E
RD7(2) 0x1F
RE0(2) 0x20
RE1(2) 0x21
RE2(2) 0x22
Note 1: Only a few of the values in this column are
valid for any given signal. For example,
since the INT signal can only be mapped
to PORTA or PORTB pins, only the regis-
ter values 0x00-0x0F (corresponding to
RA<7:0> and RB<7:0>) are valid values
to write to the INTPPS register.
2: Present on PIC16(L)F15375/76/85/86 only.
3: Present on PIC16(L)F15385/86 only.

 2016-2018 Microchip Technology Inc. DS40001866B-page 237


PIC16(L)F15356/75/76/85/86
15.3 Bidirectional Pins 15.5 PPS Permanent Lock
PPS selections for peripherals with bidirectional The PPS can be permanently locked by setting the
signals on a single pin must be made so that the PPS PPS1WAY Configuration bit. When this bit is set, the
input and PPS output select the same pin. Peripherals PPSLOCKED bit can only be cleared and set one time
that have bidirectional signals include: after a device Reset. This allows for clearing the
• EUSART (synchronous operation) PPSLOCKED bit so that the input and output selections
can be made during initialization. When the
• MSSP (I2C)
PPSLOCKED bit is set after all selections have been
made, it will remain set and cannot be cleared until after
the next device Reset event.
Note: The I2C SCLx and SDAx functions can be
remapped through PPS. However, only
certain pins have the I2C and SMBus- 15.6 Operation During Sleep
specific input buffers implemented (I2C PPS input and output selections are unaffected by Sleep.
mode disables INLVL and sets thresholds
that are specific for I2C). If the SCLx or
SDAx functions are mapped to some
15.7 Effects of a Reset
other pin, the general purpose TTL or ST A device Power-on-Reset (POR) clears all PPS input
input buffers (as configured based on and output selections to their default values (Permanent
INLVL register setting) will be used Lock Removed). All other Resets leave the selections
instead. In most applications, it is unchanged. Default input selections are shown in
therefore recommended only to map the Table 15-1 through Table 15-3.
SCLx and SDAx pin functions to the
special I2C pins, specified in the pin
allocation tables.

15.4 PPS Lock


The PPS includes a mode in which all input and output
selections can be locked to prevent inadvertent
changes. PPS selections are locked by setting the
PPSLOCKED bit of the PPSLOCK register. Setting and
clearing this bit requires a special sequence as an extra
precaution against inadvertent changes. Examples of
setting and clearing the PPSLOCKED bit are shown in
Example 15-1.

EXAMPLE 15-1: PPS LOCK/UNLOCK


SEQUENCE
; suspend interrupts
BCF INTCON,GIE
; BANKSEL PPSLOCK ; set bank
; required sequence, next 5 instructions
MOVLW 0x55
MOVWF PPSLOCK
MOVLW 0xAA
MOVWF PPSLOCK
; Set PPSLOCKED bit to disable writes or
; Clear PPSLOCKED bit to enable writes
BSF PPSLOCK,PPSLOCKED
; restore interrupts
BSF INTCON,GIE

 2016-2018 Microchip Technology Inc. DS40001866B-page 238


PIC16(L)F15356/75/76/85/86

TABLE 15-5: PPS OUTPUT SIGNAL


ROUTING OPTIONS
(PIC16(L)F15356)
Remappable to Pins of
Output RxyPPS PORTx
Signal Register
Name Value PIC16(L)F15356
PORTA PORTB PORTC
CLKR 0x1B  
NCO1OUT 0x1A  
TMR0 0x19  
SDO2/SDA2 0x18  
SCK2/SCL2 0x17  
SDO1/SDA1 0x16  
SCK1/SCL1 0x15  
C2OUT 0x14  
C1OUT 0x13  
DT2 0x12  
TX2/CK2 0x11  
DT1 0x10  
TX1/CK1 0x0F  
PWM6OUT 0x0E  
PWM5OUT 0x0D  
PWM4OUT 0x0C  
PWM3OUT 0x0B  
CCP2 0x0A  
CCP1 0x09  
CWG1D 0x08  
CWG1C 0x07  
CWG1B 0x06  
CWG1A 0x05  
CLC4OUT 0x04  
CLC3OUT 0x03  
CLC2OUT 0x02  
CLC1OUT 0x01  

 2016-2018 Microchip Technology Inc. DS40001866B-page 239


PIC16(L)F15356/75/76/85/86

TABLE 15-6: PPS OUTPUT SIGNAL ROUTING OPTIONS (PIC16(L)F15375/76)


Remappable to Pins of PORTx
Output Signal RxyPPS
Name Register Value PIC16(L)F15375/76
PORTA PORTB PORTC PORTD PORTE
CLKR 0x1B  
NCO1OUT 0x1A  
TMR0 0x19  
SDO2/SDA2 0x18  
SCK2/SCL2 0x17  
SDO1/SDA1 0x16  
SCK1/SCL1 0x15  
C2OUT 0x14  
C1OUT 0x13  
DT2 0x12  
TX2/CK2 0x11  
DT1 0x10  
TX1/CK1 0x0F  
PWM6OUT 0x0E  
PWM5OUT 0x0D  
PWM4OUT 0x0C  
PWM3OUT 0x0B  
CCP2 0x0A  
CCP1 0x09  
CWG1D 0x08  
CWG1C 0x07  
CWG1B 0x06  
CWG1A 0x05  
CLC4OUT 0x04  
CLC3OUT 0x03  
CLC2OUT 0x02  
CLC1OUT 0x01  

 2016-2018 Microchip Technology Inc. DS40001866B-page 240


PIC16(L)F15356/75/76/85/86

TABLE 15-7: PPS OUTPUT SIGNAL ROUTING OPTIONS (PIC16(L)F15385/86)


Remappable to Pins of PORTx
Output Signal RxyPPS
Name Register Value PIC16(L)F15385/86
PORTA PORTB PORTC PORTD PORTE PORTF
CLKR 0x1B  
NCO1OUT 0x1A  
TMR0 0x19  
SDO2/SDA2 0x18  
SCK2/SCL2 0X17  
SDO1/SDA1 0x16  
SCK1/SCL1 0x15  
C2OUT 0x14  
C1OUT 0x13  
DT2 0x12  
TX2/CK2 0x11  
DT1 0x10  
TX1/CK1 0x0F  
PWM6OUT 0x0E  
PWM5OUT 0x0D  
PWM4OUT 0x0C  
PWM3OUT 0x0B  
CCP2 0x0A  
CCP1 0x09  
CWG1D 0x08  
CWG1C 0x07  
CWG1B 0x06  
CWG1A 0x05  
CLC4OUT 0x04  
CLC3OUT 0x03  
CLC2OUT 0x02  
CLC1OUT 0x01  

 2016-2018 Microchip Technology Inc. DS40001866B-page 241


PIC16(L)F15356/75/76/85/86
15.8 Register Definitions: PPS Input Selection
REGISTER 15-1: xxxPPS: PERIPHERAL xxx INPUT SELECTION(1)
U-0 U-0 R/W-q/u R/W-q/u R/W/q/u R/W-q/u R/W-q/u R/W-q/u
— — xxxPPS<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = value depends on peripheral

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 xxxPPS<5:0>: Peripheral xxx Input Selection bits
See Table 15-1 through Table 15-3.

Note 1: The “xxx” in the register name “xxxPPS” represents the input signal function name, such as “INT”,
“T0CKI”, “RX”, etc. This register summary shown here is only a prototype of the array of actual registers,
as each input function has its own dedicated SFR (ex: INTPPS, T0CKIPPS, RXPPS, etc.).
2: Each specific input signal may only be mapped to a subset of these I/O pins, as shown in Table 15-1
through Table 15-3. Attempting to map an input signal to a non-supported I/O pin will result in undefined
behavior. For example, the “INT” signal map be mapped to any PORTA or PORTB pin. Therefore, the
INTPPS register may be written with values from 0x00-0x0F (corresponding to RA0-RB7). Attempting to
write 0x10 or higher to the INTPPS register is not supported and will result in undefined behavior.

 2016-2018 Microchip Technology Inc. DS40001866B-page 242


PIC16(L)F15356/75/76/85/86

REGISTER 15-2: RxyPPS: PIN Rxy OUTPUT SOURCE SELECTION REGISTER


U-0 U-0 U-0 R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W-0/u
— — — RxyPPS<4:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-5 Unimplemented: Read as ‘0’


bit 4-0 RxyPPS<4:0>: Pin Rxy Output Source Selection bits
See Table 15-5 through Table 15-7.

REGISTER 15-3: PPSLOCK: PPS LOCK REGISTER


U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0
— — — — — — — PPSLOCKED
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-1 Unimplemented: Read as ‘0’


bit 0 PPSLOCKED: PPS Locked bit
1= PPS is locked. PPS selections can not be changed.
0= PPS is not locked. PPS selections can be changed.

 2016-2018 Microchip Technology Inc. DS40001866B-page 243


PIC16(L)F15356/75/76/85/86

TABLE 15-8: SUMMARY OF REGISTERS ASSOCIATED WITH THE PPS MODULE


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
PPSLOCK — — — — — — — PPSLOCKED 243
INTPPS — — INTPPS<5:0> 242
T0CKIPPS — — T0CKIPPS<5:0> 242
T1CKIPPS — — T1CKIPPS<5:0> 242
T1GPPS — — T1GPPS<5:0> 242
T2INPPS T2INPPS<5:0> 242
CCP1PPS — — CCP1PPS<5:0> 242
CCP2PPS — — CCP2PPS<5:0> 242
CWG1PPS — — CWG1PPS<5:0> 242
SSP1CLKPPS — — SSP1CLKPPS<5:0> 242
SSP1DATPPS — — SSP1DATPPS<5:0> 242
SSP1SSPPS — — SSP1SSPPS<5:0> 242
SSP2CLKPPS — — SSP2CLKPPS<5:0> 242
SSP2DATPPS — — SSP2DATPPS<5:0> 242
SSP2SSPPS — — SSP2SSPPS<5:0> 242
RX1DTPPS — — RX1DTPPS<5:0> 242
TX1CKPPS — — TX1CKPPS<5:0> 242
CLCIN0PPS — — CLCIN0PPS<5:0> 242
CLCIN1PPS — — CLCIN1PPS<5:0> 242
CLCIN2PPS — — CLCIN2PPS<5:0> 242
CLCIN3PPS — — CLCIN3PPS<5:0> 242
RX2DTPPS — — RX2DTPPS<5:0> 242
TX2CKPPS — — TX2CKPPS<5:0> 242
ADACTPPS — — ADACTPPS<5:0> 242
RA0PPS — — — RA0PPS<4:0> 243
RA1PPS — — — RA1PPS<4:0> 243
RA2PPS — — — RA2PPS<4:0> 243
RA3PPS — — — RA3PPS<4:0> 243
RA4PPS — — — RA4PPS<4:0> 243
RA5PPS — — — RA5PPS<4:0> 243
RA6PPS — — — RA6PPS<4:0> 243
RA7PPS — — — RA7PPS<4:0> 243
RB0PPS — — — RB0PPS<4:0> 243
RB1PPS — — — RB1PPS<4:0> 243
RB2PPS — — — RB2PPS<4:0> 243
RB3PPS — — — RB3PPS<4:0> 243
RB4PPS — — — RB4PPS<4:0> 243
RB5PPS — — — RB5PPS<4:0> 243
RB6PPS — — — RB6PPS<4:0> 243
RB7PPS — — — RB7PPS<4:0> 243
RC0PPS — — — RC0PPS<4:0> 243
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the PPS module.
Note 1: Present only on PIC16(L)F15375/76/85/86.
2: Present only on PIC16(L)F15385/86.

 2016-2018 Microchip Technology Inc. DS40001866B-page 244


PIC16(L)F15356/75/76/85/86
TABLE 15-8: SUMMARY OF REGISTERS ASSOCIATED WITH THE PPS MODULE (CONTINUED)
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
RC1PPS — — — RC1PPS<4:0> 243
RC2PPS — — — RC2PPS<4:0> 243
RC3PPS — — — RC3PPS<4:0> 243
RC4PPS — — — RC4PPS<4:0> 243
RC5PPS — — — RC5PPS<4:0> 243
RC6PPS — — — RC6PPS<4:0> 243
RC7PPS — — — RC7PPS<4:0> 243
RD0PPS(1) — — — RD0PPS<4:0> 243
RD1PPS(1) — — — RD1PPS<4:0> 243
RD2PPS(1) — — — RD2PPS<4:0> 243
RD3PPS(1) — — — RD3PPS<4:0> 243
(1)
RD4PPS — — — RD4PPS<4:0> 243
RD5PPS(1) — — — RD5PPS<4:0> 243
RD6PPS(1) — — — RD6PPS<4:0> 243
(1)
RD7PPS — — — RD7PPS<4:0> 243
RE0PPS(1) — — — RD5PPS<4:0> 243
RE1PPS(1) — — — RD6PPS<4:0> 243
RE2PPS(1) — — — RD7PPS<4:0> 243
(2)
RF0PPS — — — RF0PPS<4:0> 243
RF1PPS(2) — — — RF1PPS<4:0> 243
RF2PPS(2) — — — RF2PPS<4:0> 243
RF3PPS(2) — — — RF3PPS<4:0> 243
RF4PPS(2) — — — RF4PPS<4:0> 243
RF5PPS(2) — — — RF5PPS<4:0> 243
RF6PPS(2) — — — RF6PPS<4:0> 243
RF7PPS(2) — — — RF7PPS<4:0> 243
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the PPS module.
Note 1: Present only on PIC16(L)F15375/76/85/86.
2: Present only on PIC16(L)F15385/86.

 2016-2018 Microchip Technology Inc. DS40001866B-page 245


PIC16(L)F15356/75/76/85/86
16.0 PERIPHERAL MODULE 16.2 Enabling a module
DISABLE When the register bit is cleared, the module is re-
The PIC16(L)F15356/75/76/85/86 provides the ability enabled and will be in its Reset state; SFR data will
to disable selected modules, placing them into the reflect the POR Reset values.
lowest possible Power mode. Depending on the module, it may take up to one full
For legacy reasons, all modules are ON by default instruction cycle for the module to become active.
following any Reset. There should be no interaction with the module
(e.g., writing to registers) for at least one instruction
after it has been re-enabled.
16.1 Disabling a Module
Disabling a module has the following effects: 16.3 Disabling a Module
• All clock and control inputs to the module are When a module is disabled, all the associated PPS
suspended; there are no logic transitions, and the selection registers (Registers xxxPPS Register 15-1,
module will not function. 15-2, and 15-3), are also disabled.
• The module is held in Reset:
- Writing to SFRs is disabled 16.4 System Clock Disable
- Reads return 00h
Setting SYSCMD (PMD0, Register 16-1) disables the
system clock (FOSC) distribution network to the
peripherals. Not all peripherals make use of SYSCLK,
so not all peripherals are affected. Refer to the specific
peripheral description to see if it will be affected by this
bit.

 2016-2018 Microchip Technology Inc. DS40001866B-page 246


PIC16(L)F15356/75/76/85/86
16.5 Register Definitions: Peripheral Module Disable Control

REGISTER 16-1: PMD0: PMD CONTROL REGISTER 0


R/W-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
SYSCMD FVRMD — — — NVMMD CLKRMD IOCMD
7 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 SYSCMD: Disable Peripheral System Clock Network bit


See description in Section 16.4 “System Clock Disable”.
1 = System clock network disabled (a.k.a. FOSC)
0 = System clock network enabled
bit 6 FVRMD: Disable Fixed Voltage Reference (FVR) bit
1 = FVR module disabled
0 = FVR module enabled
bit 5-3 Unimplemented: Read as ‘0’
bit 2 NVMMD: NVM Module Disable bit(1)
1 = User memory reading and writing is disabled; NVMCON registers cannot be written; FSR access
to these locations returns zero.
0 = NVM module enabled
bit 1 CLKRMD: Disable Clock Reference CLKR bit
1 = CLKR module disabled
0 = CLKR module enabled
bit 0 IOCMD: Disable Interrupt-on-Change bit, All Ports
1 = IOC module(s) disabled
0 = IOC module(s) enabled

Note 1: When enabling NVM, a delay of up to 1 µs may be required before accessing data.

 2016-2018 Microchip Technology Inc. DS40001866B-page 247


PIC16(L)F15356/75/76/85/86
REGISTER 16-2: PMD1: PMD CONTROL REGISTER 1
R/W-0/0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
NCO1MD — — — — TMR2MD TMR1MD TMR0MD
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 NCO1MD: Disable Numerically Control Oscillator bit


1 = NCO1 module disabled
0 = NCO1 module enabled
bit 6-3 Unimplemented: Read as ‘0’
bit 2 TMR2MD: Disable Timer TMR2 bit
1 = Timer2 module disabled
0 = Timer2 module enabled
bit 1 TMR1MD: Disable Timer TMR1 bit
1 = Timer1 module disabled
0 = Timer1 module enabled
bit 0 TMR0MD: Disable Timer TMR0 bit
1 = Timer0 module disabled
0 = Timer0 module enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 248


PIC16(L)F15356/75/76/85/86
REGISTER 16-3: PMD2: PMD CONTROL REGISTER 2
U-0 R/W-0/0 R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
— DAC1MD ADCMD — — CMP2MD CMP1MD ZCDMD
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 Unimplemented: Read as ‘0’


bit 6 DAC1MD: Disable DAC1 bit
1 = DAC module disabled
0 = DAC module enabled
bit 5 ADCMD: Disable ADC bit
1 = ADC module disabled
0 = ADC module enabled
bit 4-3 Unimplemented: Read as ‘0’
bit 2 CMP2MD: Disable Comparator C2 bit
1 = C2 module disabled
0 = C2 module enabled
bit 1 CMP1MD: Disable Comparator C1 bit
1 = C1 module disabled
0 = C1 module enabled
bit 0 ZCDMD: Disable ZCD bit
1 = ZCD module disabled
0 = ZCD module enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 249


PIC16(L)F15356/75/76/85/86
REGISTER 16-4: PMD3: PMD CONTROL REGISTER 3
U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — PWM6MD PWM5MD PWM4MD PWM3MD CCP2MD CCP1MD
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-6 Unimplemented: Read as ‘0’


bit 5 PWM6MD: Disable Pulse-Width Modulator PWM6 bit
1 = PWM6 module disabled
0 = PWM6 module enabled
bit 4 PWM5MD: Disable Pulse-Width Modulator PWM5 bit
1 = PWM5 module disabled
0 = PWM5 module enabled
bit 3 PWM4MD: Disable Pulse-Width Modulator PWM4 bit
1 = PWM4 module disabled
0 = PWM4 module enabled
bit 2 PWM3MD: Disable Pulse-Width Modulator PWM3 bit
1 = PWM3 module disabled
0 = PWM3 module enabled
bit 1 CCP2MD: Disable CCP2 bit
1 = CCP2 module disabled
0 = CCP2 module enabled
bit 0 CCP1MD: Disable CCP1 bit
1 = CCP1 module disabled
0 = CCP1 module enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 250


PIC16(L)F15356/75/76/85/86
REGISTER 16-5: PMD4: PMD CONTROL REGISTER 4
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0
UART2MD UART1MD MSSP2MD MSSP1MD — — — CWG1MD
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 UART2MD: Disable EUSART2 bit


1 = EUSART2 module disabled
0 = EUSART2 module enabled
bit 6 UART1MD: Disable EUSART1 bit
1 = EUSART1 module disabled
0 = EUSART1 module enabled
bit 5 MSSP2MD: Disable MSSP2 bit
1 = MSSP2 module disabled
0 = MSSP2 module enabled
bit 4 MSSP1MD: Disable MSSP1 bit
1 = MSSP1 module disabled
0 = MSSP1 module enabled
bit 3-1 Unimplemented: Read as ‘0’
bit 0 CWG1MD: Disable CWG1 bit
1 = CWG1 module disabled
0 = CWG1 module enabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 251


PIC16(L)F15356/75/76/85/86
REGISTER 16-6: PMD5 – PMD CONTROL REGISTER 5
U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0
— — — CLC4MD CLC3MD CLC2MD CLC1MD —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-5 Unimplemented: Read as ‘0’


bit 4 CLC4MD: Disable CLC4 bit
1 = CLC4 module disabled
0 = CLC4 module enabled
bit 3 CLC3MD: Disable CLC3 bit
1 = CLC3 module disabled
0 = CLC3 module enabled
bit 2 CLC2MD: Disable CLC2 bit
1 = CLC2 module disabled
0 = CLC2 module enabled
bit 1 CLC1MD: Disable CLC1 bit
1 = CLC1 module disabled
0 = CLC1 module enabled
bit 0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 252


PIC16(L)F15356/75/76/85/86

TABLE 16-1: SUMMARY OF REGISTERS ASSOCIATED WITH THE PMD MODULE


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
PMD0 SYSCMD FVRMD — — — NVMMD CLKRMD IOCMD 247
PMD1 NCO1MD — — — — TMR2MD TMR1MD TMR0MD 248
PMD2 — DAC1MD ADCMD — — CMP2MD CMP1MD ZCDMD 249
PMD3 — — PWM6MD PWM5MD PWM4MD PWM3MD CCP2MD CCP1MD 250
PMD4 UART2MD UART1MD MSSP2MD MSSP1MD — — — CWG1MD 251
PMD5 — — — CLC4MD CLC3MD CLC2MD CLC1MD — 252
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the PMD module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 253


PIC16(L)F15356/75/76/85/86
17.0 INTERRUPT-ON-CHANGE 17.3 Interrupt Flags
All pins on ports A, B and C and lower four bits of PORTE The bits located in the IOCxF registers are status flags
can be configured to operate as Interrupt-on-Change that correspond to the interrupt-on-change pins of each
(IOC) pins. An interrupt can be generated by detecting a port. If an expected edge is detected on an appropriately
signal that has either a rising edge or a falling edge. Any enabled pin, then the status flag for that pin will be set,
individual pin, or combination of pins, can be configured and an interrupt will be generated if the IOCIE bit is set.
to generate an interrupt. The interrupt-on-change The IOCIF bit of the PIR0 register reflects the status of
module has the following features: all IOCxF bits.
• Interrupt-on-Change enable (Master Switch)
17.3.1 CLEARING INTERRUPT FLAGS
• Individual pin configuration
The individual status flags, (IOCxF register bits), can be
• Rising and falling edge detection
cleared by resetting them to zero. If another edge is
• Individual pin interrupt flags detected during this clearing operation, the associated
Figure 17-1 is a block diagram of the IOC module. status flag will be set at the end of the sequence,
regardless of the value actually being written.
17.1 Enabling the Module In order to ensure that no detected edge is lost while
clearing flags, only AND operations masking out known
To allow individual pins to generate an interrupt, the
changed bits should be performed. The following
IOCIE bit of the PIE0 register must be set. If the IOCIE
sequence is an example of what should be performed.
bit is disabled, the edge detection on the pin will still
occur, but an interrupt will not be generated.
EXAMPLE 17-1: CLEARING INTERRUPT
FLAGS
17.2 Individual Pin Configuration
(PORTA EXAMPLE)
For each pin, a rising edge detector and a falling edge MOVLW0xff
detector are present. To enable a pin to detect a rising XORWFIOCAF, W
edge, the associated bit of the IOCxP register is set. To ANDWFIOCAF, F
enable a pin to detect a falling edge, the associated bit
of the IOCxN register is set.
A pin can be configured to detect rising and falling 17.4 Operation in Sleep
edges simultaneously by setting the associated bits in The interrupt-on-change interrupt event will wake the
both of the IOCxP and IOCxN registers. device from Sleep mode, if the IOCIE bit is set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 254


PIC16(L)F15356/75/76/85/86
FIGURE 17-1: INTERRUPT-ON-CHANGE BLOCK DIAGRAM (PORTB EXAMPLE)
Rev. 10-000037C
9/14/2016

IOCBNx D Q

edge
detect

RBx

data bus = S to data bus


IOCBPx D Q
0 or 1
D Q
IOCBFx

R write IOCBFx
IOCIE
IOC interrupt
RESET to CPU core

from all other


IOCnFx individual
pin detectors

Note 1: See Table 8-1 for BOR Active Conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 255


PIC16(L)F15356/75/76/85/86
17.5 Register Definitions: Interrupt-on-Change Control

REGISTER 17-1: IOCAP: INTERRUPT-ON-CHANGE PORTA POSITIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCAP7 IOCAP6 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCAP<7:0>: Interrupt-on-Change PORTA Positive Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a positive-going edge. IOCAFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.

REGISTER 17-2: IOCAN: INTERRUPT-ON-CHANGE PORTA NEGATIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCAN7 IOCAN6 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCAN<7:0>: Interrupt-on-Change PORTA Negative Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a negative-going edge. IOCAFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 256


PIC16(L)F15356/75/76/85/86

REGISTER 17-3: IOCAF: INTERRUPT-ON-CHANGE PORTA FLAG REGISTER


R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
IOCAF7 IOCAF6 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-0 IOCAF<7:0>: Interrupt-on-Change PORTA Flag bits


1 = An enabled change was detected on the associated pin.
Set when IOCAPx = 1 and a rising edge was detected on RAx, or when IOCANx = 1 and a falling
edge was detected on RAx.
0 = No change was detected, or the user cleared the detected change.

 2016-2018 Microchip Technology Inc. DS40001866B-page 257


PIC16(L)F15356/75/76/85/86

REGISTER 17-4: IOCBP: INTERRUPT-ON-CHANGE PORTB POSITIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
(1) (1)
IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCBP<7:0>: Interrupt-on-Change PORTB Positive Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a positive-going edge. IOCBFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.
Note 1: If the debugger is enabled, these bits are not available for use.

REGISTER 17-5: IOCBN: INTERRUPT-ON-CHANGE PORTB NEGATIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCBN7(1) IOCBN6(1) IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCBN<7:0>: Interrupt-on-Change PORTB Negative Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a negative-going edge. IOCBFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.
Note 1: If the debugger is enabled, these bits are not available for use.

 2016-2018 Microchip Technology Inc. DS40001866B-page 258


PIC16(L)F15356/75/76/85/86

REGISTER 17-6: IOCBF: INTERRUPT-ON-CHANGE PORTB FLAG REGISTER


R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
(1) (1)
IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-0 IOCBF<7:0>: Interrupt-on-Change PORTB Flag bits


1 = An enabled change was detected on the associated pin.
Set when IOCBPx = 1 and a rising edge was detected on RBx, or when IOCBNx = 1 and a falling
edge was detected on RBx.
0 = No change was detected, or the user cleared the detected change.
Note 1: If the debugger is enabled, these bits are not available for use.

 2016-2018 Microchip Technology Inc. DS40001866B-page 259


PIC16(L)F15356/75/76/85/86

REGISTER 17-7: IOCCP: INTERRUPT-ON-CHANGE PORTC POSITIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCCP<7:0>: Interrupt-on-Change PORTC Positive Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a positive-going edge. IOCCFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin

REGISTER 17-8: IOCCN: INTERRUPT-ON-CHANGE PORTC NEGATIVE EDGE REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 IOCCN<7:0>: Interrupt-on-Change PORTC Negative Edge Enable bits


1 = Interrupt-on-Change enabled on the pin for a negative-going edge. IOCCFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin

 2016-2018 Microchip Technology Inc. DS40001866B-page 260


PIC16(L)F15356/75/76/85/86

REGISTER 17-9: IOCCF: INTERRUPT-ON-CHANGE PORTC FLAG REGISTER


R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-0 IOCCF<7:0>: Interrupt-on-Change PORTC Flag bits


1 = An enabled change was detected on the associated pin
Set when IOCCPx = 1 and a rising edge was detected on RCx, or when IOCCNx = 1 and a falling
edge was detected on RCx.
0 = No change was detected, or the user cleared the detected change

REGISTER 17-10: IOCEP: INTERRUPT-ON-CHANGE PORTE POSITIVE EDGE REGISTER


U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
— — — — IOCEP3(2) IOCEP2(1) IOCEP1(1) IOCEP0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 IOCEP<3:0>: Interrupt-on-Change PORTE Positive Edge Enable bit
1 = Interrupt-on-Change enabled on the pin for a positive-going edge. IOCCFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin

Note 1: Present only on PIC16(L)F15375/76/85/86.


2: If MCLRE=1 or LVP=1, port functionality is disabled and IOC on that pin is not available.

 2016-2018 Microchip Technology Inc. DS40001866B-page 261


PIC16(L)F15356/75/76/85/86

REGISTER 17-11: IOCEN: INTERRUPT-ON-CHANGE PORTE NEGATIVE EDGE REGISTER


U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
(2) (1) (1)
— — — — IOCEN3 IOCEN2 IOCEN1 IOCEN0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 IOCEN<3:0>: Interrupt-on-Change PORTE Negative Edge Enable bit
1 = Interrupt-on-Change enabled on the pin for a negative-going edge. IOCCFx bit and IOCIF flag will
be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin

Note 1: Present only on PIC16(L)F15375/76/85/86.


2: If MCLRE=1 or LVP=1, port functionality is disabled and IOC on that pin is not available.

REGISTER 17-12: IOCEF: INTERRUPT-ON-CHANGE PORTE FLAG REGISTER


U-0 U-0 U-0 U-0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
— — — — IOCEF3(2) IOCEF2(1) IOCEF1(1) IOCEF0(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware

bit 7-4 Unimplemented: Read as ‘0’


bit 3 IOCEF<3:0>: Interrupt-on-Change PORTE Flag bit
1 = An enabled change was detected on the associated pin
Set when IOCCPx = 1 and a rising edge was detected on RCx, or when IOCCNx = 1 and a falling
edge was detected on RCx.
0 = No change was detected, or the user cleared the detected change

Note 1: Present only on PIC16(L)F15375/76/85/86.


2: If MCLRE=1 or LVP=1, port functionality is disabled and IOC on that pin is not available.

 2016-2018 Microchip Technology Inc. DS40001866B-page 262


PIC16(L)F15356/75/76/85/86
TABLE 17-1: SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPT-ON-CHANGE
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
INTCON GIE PEIE — — — — — INTEDG 147
PIE0 — — TMR0IE IOCIE — — — INTE 148
IOCAP IOCAP7 IOCAP6 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 256
IOCAN IOCAN7 IOCAN6 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 256
IOCAF IOCAF7 IOCAF6 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 257
IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 258
IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 258
IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 259
IOCCP IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0 260
IOCCN IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0 260
IOCCF IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0 261
IOCEP — — — — IOCEP3 IOCEP2(1) IOCEP1(1) IOCEP0(1) 261
IOCEN — — — — IOCEN3 IOCEN2(1) IOCEN1(1) IOCEN0(1) 262
(1) (1) (1)
IOCEF — — — — IOCEF3 IOCEF2 IOCEF1 IOCEF0 262
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by interrupt-on-change.
Note 1: Present only in PIC16(L)F15375/76/85/86.

 2016-2018 Microchip Technology Inc. DS40001866B-page 263


PIC16(L)F15356/75/76/85/86
18.0 FIXED VOLTAGE REFERENCE 18.1 Independent Gain Amplifiers
(FVR) The output of the FVR, which is connected to the ADC,
The Fixed Voltage Reference, or FVR, is a stable comparators, and DAC, is routed through two
voltage reference, independent of VDD, with 1.024V, independent programmable gain amplifiers. Each
2.048V or 4.096V selectable output levels. The output amplifier can be programmed for a gain of 1x, 2x or 4x,
of the FVR can be configured to supply a reference to produce the three possible voltage levels.
voltage to the following: The ADFVR<1:0> bits of the FVRCON register are
• ADC input channel used to enable and configure the gain amplifier settings
for the reference supplied to the ADC module.
• ADC positive reference
Reference Section 20.0 “Analog-to-Digital
• Comparator positive and negative input Converter (ADC) Module” for additional information.
• Digital-to-Analog Converter (DAC)
The CDAFVR<1:0> bits of the FVRCON register are used
The FVR can be enabled by setting the FVREN bit of to enable and configure the gain amplifier settings for the
the FVRCON register. reference supplied to the DAC and comparator module.
Reference Section 21.0 “5-Bit Digital-to-Analog
Converter (DAC1) Module” and Section 23.0
Note: Fixed Voltage Reference output cannot “Comparator Module” for additional information.
exceed VDD.
18.2 FVR Stabilization Period
When the Fixed Voltage Reference module is enabled,
it requires time for the reference and amplifier circuits
to stabilize.
FVRRDY is an indicator of the reference being ready.
In the case of an LF device, or a device on which the
BOR is enabled in the Configuration Word settings,
then the FVRRDY bit will be high prior to setting
FVREN as those module require the reference voltage.

FIGURE 18-1: VOLTAGE REFERENCE BLOCK DIAGRAM


Rev. 10-000053D
9/15/2016

2
ADFVR<1:0>

1x
2x ADC FVR Buffer
4x

2
CDAFVR<1:0>

1x
Comparator and DAC
2x
4x FVR Buffer

FVREN

Voltage
FVRRDY (Note 1)
Reference

Note 1: FVRRDY is always ‘1’.


2: Any peripheral requiring the Fixed Reference (See Table 18-1).

 2016-2018 Microchip Technology Inc. DS40001866B-page 264


PIC16(L)F15356/75/76/85/86
18.3 Register Definitions: FVR Control

REGISTER 18-1: FVRCON: FIXED VOLTAGE REFERENCE CONTROL REGISTER


R/W-0/0 R-q/q R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
(1) (3) (3)
FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 FVREN: Fixed Voltage Reference Enable bit


1 = Fixed Voltage Reference is enabled
0 = Fixed Voltage Reference is disabled
bit 6 FVRRDY: Fixed Voltage Reference Ready Flag bit(1)
1 = Fixed Voltage Reference output is ready for use
0 = Fixed Voltage Reference output is not ready or not enabled
bit 5 TSEN: Temperature Indicator Enable bit(3)
1 = Temperature Indicator is enabled
0 = Temperature Indicator is disabled
bit 4 TSRNG: Temperature Indicator Range Selection bit(3)
1 = Temperature in High Range VOUT = 3VT
0 = Temperature in Low Range VOUT = 2VT
bit 3-2 CDAFVR<1:0>: Comparator FVR Buffer Gain Selection bits
11 =Comparator FVR Buffer Gain is 4x, (4.096V)(2)
10 =Comparator FVR Buffer Gain is 2x, (2.048V)(2)
01 =Comparator FVR Buffer Gain is 1x, (1.024V)
00 =Comparator FVR Buffer is off
bit 1-0 ADFVR<1:0>: ADC FVR Buffer Gain Selection bit
11 =ADC FVR Buffer Gain is 4x, (4.096V)(2)
10 =ADC FVR Buffer Gain is 2x, (2.048V)(2)
01 =ADC FVR Buffer Gain is 1x, (1.024V)
00 =ADC FVR Buffer is off

Note 1: FVRRDY is always ‘1’.


2: Fixed Voltage Reference output cannot exceed VDD.
3: See Section 19.0 “Temperature Indicator Module” for additional information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 265


PIC16(L)F15356/75/76/85/86
TABLE 18-1: SUMMARY OF REGISTERS ASSOCIATED WITH FIXED VOLTAGE REFERENCE
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 265
ADCON0 CHS<5:0> GO/DONE ADON 278
ADCON1 ADFM ADCS<2:0> — — ADPREF<1:0> 280
DAC1CON0 DAC1EN — DAC1OE1 DAC1OE2 DAC1PSS<1:0> — DAC1NSS 288
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used with the Fixed Voltage Reference.

 2016-2018 Microchip Technology Inc. DS40001866B-page 266


PIC16(L)F15356/75/76/85/86
19.0 TEMPERATURE INDICATOR 19.1.1 TEMPERATURE INDICATOR
MODULE RANGE
The temperature indicator circuit operates in either high
This family of devices is equipped with a temperature
or low range. The high range, selected by setting the
circuit designed to measure the operating temperature
TSRNG bit of the FVRCON register, provides a wider
of the silicon die.
output voltage. This provides more resolution over the
The circuit’s range of operating temperature falls temperature range. High range requires a higher-bias
between -40°C and +125°C. A one-point calibration voltage to operate and thus, a higher VDD is needed.
allows the circuit to indicate a temperature closely The low range is selected by clearing the TSRNG bit of
surrounding that point. A two-point calibration allows the FVRCON register. The low range generates a lower
the circuit to sense the entire range of temperature sensor voltage and thus, a lower VDD voltage is needed
more accurately. to operate the circuit.
The output voltage of the sensor is the highest value at
19.1 Module Operation -40°C and the lowest value at +125°C.
The temperature indicator module consists of a • High Range: The High range is used in applica-
temperature-sensing circuit that provides a voltage to tions with the reference for the ADC,
the device ADC. The analog voltage output, VMEAS, VREF = 2.048V. This range may not be suitable for
varies inversely to the device temperature. The output of battery-powered applications. The ADC reading
the temperature indicator is referred to as VMEAS. (in counts) at 90°C for the high range setting is
Figure 19-1 shows a simplified block diagram of the stored in the DIA Table (Table 6-1) as parameter
temperature indicator module. TSHR2.
• Low Range: This mode is useful in applications in
FIGURE 19-1: TEMPERATURE which the VDD is too low for high-range operation.
The VDD in this mode can be as low as 1.8V. VDD
INDICATOR MODULE
must, however, be at least 0.5V higher than the
BLOCK DIAGRAM
maximum sensor voltage depending on the
5HY'
 expected low operating temperature. The ADC
reading (in counts) at 90°C for the Low range set-
9'' ting is stored in the DIA Table (Table 6-1) as
parameter TSLR2.

19.1.2 MINIMUM OPERATING VDD


7651* 90($6
7HPSHUDWXUH,QGLFDWRU
7R$'& When the temperature circuit is operated in low range,
0RGXOH
76(1 the device may be operated at any operating voltage
that is within specifications. When the temperature
circuit is operated in high range, the device operating
voltage, VDD, must be high enough to ensure that the
*1' temperature circuit is correctly biased.
Table 19-1 shows the recommended minimum VDD vs.
The output of the circuit is measured using the internal
Range setting.
Analog-to-Digital Converter. A channel is reserved for
the temperature circuit output. Refer to Section 20.0 TABLE 19-1: RECOMMENDED VDD vs.
“Analog-to-Digital Converter (ADC) Module” for RANGE
detailed information. Min.VDD, TSRNG = 1 Min. VDD, TSRNG = 0
The ON/OFF bit for the module is located in the (High Range) (Low Range)
FVRCON register. See Section 18.0 “Fixed Voltage  2.5  1.8
Reference (FVR)” for more information. The circuit is
enabled by setting the TSEN bit of the FVRCON
register. When the module is disabled, the circuit draws
no current.
The circuit operates in either High or Low range. Refer
to Section 19.1.1 “Temperature Indicator Range” for
more details on the range settings.

 2016-2018 Microchip Technology Inc. DS40001866B-page 267


PIC16(L)F15356/75/76/85/86
19.2 Temperature Calculation
Note 1: It is recommended to take the average of
This section describes the steps involved in calculating
ten measurements of ADCmeas to
the die temperature, TMEAS:
reduce noise and improve accuracy.
1. Obtain the ADC count value of the measured
2: Refer to Section 37.0, Electrical Specifi-
analog voltage: The analog output voltage,
cations for FVR reference voltage accu-
VMEAS is converted to a digital count value by
racy.
the Analog to Digital Converter (ADC) and is
referred to as ADCMEAS.
19.2.1 CALIBRATION
2. Obtain the ADC count value, ADCDIA at 90
degrees, in the DIA table (Table 6-1). This 19.2.1.1 Higher-Order Calibration
parameter is TSLR2 for the low range setting or
TSHR2 for the high range setting of the If the application requires more precise temperature
temperature indicator module. measurement, additional calibrations steps will be
necessary. For these applications, two-point or three-
3. Obtain the output analog voltage (in mV) value
point calibration is recommended.
of the Fixed Reference Voltage (FVR) for 2x
setting, from the DIA Table. This parameter is
FVRA2X in the DIA table (Table 5-3). 19.3 ADC Acquisition Time
4. Obtain the value of the temperature indicator To ensure accurate temperature measurements, the
voltage sensitivity, parameter Mv, from Table 37- user must wait a certain minimum acquisition time
26 for the corresponding range setting. (parameter TS01 in Table 37-26) for the ADC value to
Equation 19-1 provides an estimate for the die settle, after the ADC input multiplexer is connected to
temperature based on the above parameters. the temperature indicator output, before the conversion
is performed.
EQUATION 19-1: SENSOR TEMPERATURE
 ADC MEAS – ADC DIA   FVRA2X
T MEAS = 90 + --------------------------------------------------------------------------------------------
-
N
2 – 1  Mv
Where:
ADCMEAS = ADC reading at temperature being
estimated
ADCDIA = ADC reading stored in the DIA
FVRA2X = FVR value stored in the DIA for 2x setting
N = Resolution of the ADC
Mv = Temperature Indicator voltage sensitivity (mV/°C)

TABLE 19-2: SUMMARY OF REGISTERS ASSOCIATED WITH THE TEMPERATURE INDICATOR(1)


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
FVRCON EN RDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 265
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are unused by the temperature indicator module.
Note 1: It is recommended to take the average of ten measurements of ADCMEAS to reduce noise and improve
accuracy.

 2016-2018 Microchip Technology Inc. DS40001866B-page 268


PIC16(L)F15356/75/76/85/86
20.0 ANALOG-TO-DIGITAL The ADC voltage reference is software selectable to be
either internally generated or externally supplied.
CONVERTER (ADC) MODULE
The ADC can generate an interrupt upon completion of
The Analog-to-Digital Converter (ADC) allows a conversion. This interrupt can be used to wake-up the
conversion of an analog input signal to a 10-bit binary device from Sleep.
representation of that signal. This device uses analog
inputs, which are multiplexed into a single sample and
hold circuit. The output of the sample and hold is
connected to the input of the converter. The converter
generates a 10-bit binary result via successive
approximation and stores the conversion result into the
ADC result registers (ADRESH:ADRESL register pair).
Figure 20-1 shows the block diagram of the ADC.

FIGURE 20-1: ADC BLOCK DIAGRAM

VDD ADPREF Rev. 10-000033A


7/30/2013

Positive
VDD Reference
Select

VREF+ pin

VSS ADCS<2:0>
AN0
ANa VRNEG VRPOS
External .
Channel FOSC/n Fosc
. Divider FOSC
Inputs ADC
ADC_clk
. sampled Clock
ANz input Select FRC
FRC
Temp Indicator
Internal
Channel DACx_output ADC CLOCK SOURCE
Inputs
FVR_buffer1 ADC
Sample Circuit
CHS<4:0>
ADFM
set bit ADIF

10
complete 10-bit Result
Write to bit
GO/DONE
GO/DONE Q1 16
start
Q4
ADRESH ADRESL
Q2 Enable

Trigger Select
TRIGSEL<3:0> ADON
. . . VSS
Trigger Sources

AUTO CONVERSION
TRIGGER

 2016-2018 Microchip Technology Inc. DS40001866B-page 269


PIC16(L)F15356/75/76/85/86
20.1 ADC Configuration
When configuring and using the ADC the following Note: It is recommended that when switching
functions must be considered: from an ADC channel of a higher voltage
to a channel of a lower voltage, that the
• Port configuration
user selects the VSS channel before con-
• Channel selection necting to the channel with the lower volt-
• ADC voltage reference selection age. If the ADC does not have a dedicated
• ADC conversion clock source VSS input channel, the VSS selection
• Interrupt control (DAC1R<4:0> = b’00000’) through the
DAC output channel can be used. If the
• Result formatting
DAC is in use, a free input channel can be
20.1.1 PORT CONFIGURATION connected to VSS, and can be used in
place of the DAC.
The ADC can be used to convert both analog and
digital signals. When converting analog signals, the I/O
pin will be configured for analog by setting the
associated TRIS and ANSEL bits. Refer to
Section 14.0 “I/O Ports” for more information.
Note: Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.

20.1.2 CHANNEL SELECTION


There are several channel selections available:
• Seven Port A channels
• Seven Port B channels
• Seven Port C channels
• Seven Port D channels(1)
• Three Port E channels(1)
• Seven Port F channels(2)
• Temperature Indicator
• DAC output
• Fixed Voltage Reference (FVR)
• AVSS (Ground)
Note 1: Present on PIC16(L)F15375/76/85/86 only.
2: Present on PIC16(L)F15385/86 only.
The CHS<5:0> bits of the ADCON0 register
(Register 20-1) determine which channel is connected
to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 20.2
“ADC Operation” for more information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 270


PIC16(L)F15356/75/76/85/86
20.1.3 ADC VOLTAGE REFERENCE
The ADPREF<1:0> bits of the ADCON1 register
provides control of the positive voltage reference. The
positive voltage reference can be:
• VREF+ pin
• VDD
• FVR 2.048V
• FVR 4.096V (Not available on LF devices)
The ADPREF bit of the ADCON1 register provides
control of the negative voltage reference. The negative
voltage reference can be:
• VREF- pin
• VSS
See Section 18.0 “Fixed Voltage Reference (FVR)”
for more details on the Fixed Voltage Reference.

20.1.4 CONVERSION CLOCK


The source of the conversion clock is software
selectable via the ADCS<2:0> bits of the ADCON1
register. There are seven possible clock options:
• FOSC/2
• FOSC/4
• FOSC/8
• FOSC/16
• FOSC/32
• FOSC/64
• ADCRC (dedicated RC oscillator)
The time to complete one bit conversion is defined as
TAD. One full 10-bit conversion requires 11.5 TAD
periods as shown in Figure 20-2.
For correct conversion, the appropriate TAD specification
must be met. Refer to Table 37-13 for more information.
Table 20-1 gives examples of appropriate ADC clock
selections.
Note: Unless using the ADCRC, any changes in
the system clock frequency will change
the ADC clock frequency, which may
adversely affect the ADC result.

 2016-2018 Microchip Technology Inc. DS40001866B-page 271


PIC16(L)F15356/75/76/85/86

TABLE 20-1: ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES
ADC Clock Period (TAD) Device Frequency (FOSC)

ADC
ADCS<2:0> 32 MHz 20 MHz 16 MHz 8 MHz 4 MHz 1 MHz
Clock Source
FOSC/2 000 62.5ns(2) 100 ns(2) 125 ns(2) 250 ns(2) 500 ns(2) 2.0 s
(2) (2) (2) (2)
FOSC/4 100 125 ns 200 ns 250 ns 500 ns 1.0 s 4.0 s
FOSC/8 001 0.5 s(2) 400 ns(2) 0.5 s(2) 1.0 s 2.0 s 8.0 s(3)
FOSC/16 101 800 ns 800 ns 1.0 s 2.0 s 4.0 s 16.0 s(3)
(3)
FOSC/32 010 1.0 s 1.6 s 2.0 s 4.0 s 8.0 s 32.0 s(2)
FOSC/64 110 2.0 s 3.2 s 4.0 s 8.0 s(3) 16.0 s(2) 64.0 s(2)
(1,4) (1,4) (1,4) (1,4) (1,4)
ADCRC x11 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s(1,4)
Legend: Shaded cells are outside of recommended range.
Note 1: See TAD parameter for ADCRC source typical TAD value.
2: These values violate the required TAD time.
3: Outside the recommended TAD time.
4: The ADC clock period (TAD) and total ADC conversion time can be minimized when the ADC clock is derived
from the system clock FOSC. However, the ADCRC oscillator source must be used when conversions are to be
performed with the device in Sleep mode.

FIGURE 20-2: ANALOG-TO-DIGITAL CONVERSION TAD CYCLES


Rev. 10-000035A
7/30/2013

TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11

b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

THCD
Conversion Starts
TACQ On the following cycle:
Holding capacitor disconnected
from analog input (THCD).
ADRESH:ADRESL is loaded,
GO bit is cleared,
Set GO bit ADIF bit is set,
holding capacitor is reconnected to analog input.
Enable ADC (ADON bit)
and
Select channel (ACS bits)

 2016-2018 Microchip Technology Inc. DS40001866B-page 272


PIC16(L)F15356/75/76/85/86
20.1.5 INTERRUPTS 20.1.6 RESULT FORMATTING
The ADC module allows for the ability to generate an The 10-bit ADC conversion result can be supplied in
interrupt upon completion of an Analog-to-Digital two formats, left justified or right justified. The ADFM bit
conversion. The ADC Interrupt Flag is the ADIF bit in of the ADCON1 register controls the output format.
the PIR1 register. The ADC Interrupt Enable is the Figure 20-3 shows the two output formats.
ADIE bit in the PIE1 register. The ADIF bit must be
cleared in software.
Note 1: The ADIF bit is set at the completion of
every conversion, regardless of whether
or not the ADC interrupt is enabled.
2: The ADC operates during Sleep only
when the ADCRC oscillator is selected.
This interrupt can be generated while the device is
operating or while in Sleep. If the device is in Sleep, the
interrupt will wake-up the device. Upon waking from
Sleep, the next instruction following the SLEEP
instruction is always executed. If the user is attempting
to wake-up from Sleep and resume in-line code
execution, the ADIE bit of the PIE1 register and the
PEIE bit of the INTCON register must both be set and
the GIE bit of the INTCON register must be cleared. If
all three of these bits are set, the execution will switch
to the Interrupt Service Routine (ISR).

FIGURE 20-3: 10-BIT ADC CONVERSION RESULT FORMAT


Rev. 10-000 054A
12/21/201 6

ADRESH ADRESL

(ADFM = 0) MSb LSb


bit 7 bit 0 bit 7 bit 0

10-bit ADC Result Unimplemented: Read as ‘0’

(ADFM = 1) MSb LSb


bit 7 bit 0 bit 7 bit 0

Unimplemented: Read as ‘0’ 10-bit ADC Result

 2016-2018 Microchip Technology Inc. DS40001866B-page 273


PIC16(L)F15356/75/76/85/86
20.2 ADC Operation
Note: The Auto-conversion feature is not avail-
20.2.1 STARTING A CONVERSION
able while the device is in Sleep mode.
To enable the ADC module, the ADON bit of the
ADCON0 register must be set to a ‘1’. Setting the GO/
DONE bit of the ADCON0 register to a ‘1’ will start the TABLE 20-2: ADC AUTO-CONVERSION
Analog-to-Digital conversion. TABLE
Note: The GO/DONE bit will not be set in the ADACT SOURCE/
DESCRIPTION
VALUE PERIPHERAL
same instruction that turns on the ADC.
Refer to Section 20.2.5 “ADC Conver- 0x00 Disabled External Trigger Disabled
sion Procedure”. 0x01 ADACTPPS Pin Selected by ADACTPPS
0x02 TMR0 Timer0 overflow condition
20.2.2 COMPLETION OF A CONVERSION 0x03 TMR1 Timer1 overflow condition

When the conversion is complete, the ADC module will: Match between Timer2 postscaled
0x04 TMR2
value and PR2
• Clear the GO/DONE bit 0x05 CCP1 CCP1 output
• Set the ADIF Interrupt Flag bit 0x06 CCP2 CCP2 output
• Update the ADRESH and ADRESL registers with 0x07 PWM3 PWM3 output
new conversion result 0x08 PWM4 PWM4 output
0x09 PWM5 PWM5 output
0x0A PWM6 PWM6 output
Note: A device Reset forces all registers to their
0x0B NCO1 NCO1 output
Reset state. Thus, the ADC module is
0x0C C1OUT Comparator C1 output
turned off and any pending conversion is
0x0D C2OUT Comparator C2 output
terminated.
0x0E IOCIF Interrupt-on change flag trigger

20.2.3 ADC OPERATION DURING SLEEP 0x0F CLC1 CLC1 output


0x10 CLC2 CLC2 output
The ADC module can operate during Sleep. This
0x11 CLC3 CLC3 output
requires the ADC clock source to be set to the ADCRC
0x12 CLC4 CLC4 output
option. When the ADCRC oscillator source is selected,
the ADC waits one additional instruction before starting 0x13-0xFF Reserved Reserved, do not use

the conversion. This allows the SLEEP instruction to be


executed, which can reduce system noise during the
conversion. If the ADC interrupt is enabled, the device
will wake-up from Sleep when the conversion
completes. If the ADC interrupt is disabled, the ADC
module is turned off after the conversion completes,
although the ADON bit remains set.
When the ADC clock source is something other than
ADCRC, a SLEEP instruction causes the present
conversion to be aborted and the ADC module is
turned off, although the ADON bit remains set.

20.2.4 AUTO-CONVERSION TRIGGER


The Auto-conversion Trigger allows periodic ADC
measurements without software intervention. When a
rising edge of the selected source occurs, the GO/
DONE bit is set by hardware.
The Auto-conversion Trigger source is selected with
the ADACT<4:0> bits of the ADACT register.
Using the Auto-conversion Trigger does not assure
proper ADC timing. It is the user’s responsibility to
ensure that the ADC timing requirements are met.
See Table 20-2 for auto-conversion sources.

 2016-2018 Microchip Technology Inc. DS40001866B-page 274


PIC16(L)F15356/75/76/85/86
20.2.5 ADC CONVERSION PROCEDURE EXAMPLE 20-1: ADC CONVERSION
This is an example procedure for using the ADC to ;This code block configures the ADC
perform an Analog-to-Digital conversion: ;for polling, Vdd and Vss references, ADCRC
;oscillator and AN0 input.
1. Configure Port: ;
;Conversion start & polling for completion ;
• Disable pin output driver (Refer to the TRIS are included.
register) ;
• Configure pin as analog (Refer to the ANSEL BANKSELADCON1;
MOVLWB’11110000’;Right justify, ADCRC
register) ;oscillator
2. Configure the ADC module: MOVWFADCON1;Vdd and Vss Vref
BANKSELTRISA;
• Select ADC conversion clock BSF TRISA,0;Set RA0 to input
• Select voltage reference BANKSELANSELA;
BSF ANSELA,0;Set RA0 to analog
• Select ADC input channel BANKSELADCON0;
MOVLWB’00000001’;Select channel AN0
• Turn on ADC module MOVWFADCON0;Turn ADC On
3. Configure ADC interrupt (optional): CALLSampleTime;Acquisiton delay
BSF ADCON0,ADGO;Start conversion
• Clear ADC interrupt flag BTFSCADCON0,ADGO;Is conversion done?
• Enable ADC interrupt GOTO$-1 ;No, test again
BANKSELADRESH;
• Enable peripheral interrupt MOVFADRESH,W;Read upper 2 bits
• Enable global interrupt(1) MOVWFRESULTHI;store in GPR space
BANKSELADRESL;
4. Wait the required acquisition time(2). MOVFADRESL,W;Read lower 8 bits
5. Start conversion by setting the GO/DONE bit. MOVWFRESULTLO;Store in GPR space

6. Wait for ADC conversion to complete by one of


the following:
• Polling the GO/DONE bit
• Waiting for the ADC interrupt
7. Read ADC Result.
8. Clear the ADC interrupt flag (required if interrupt
is enabled).

Note 1: The global interrupt can be disabled if the


user is attempting to wake-up from Sleep
and resume in-line code execution.
2: Refer to Section 20.3 “ADC Acquisi-
tion Requirements”.

 2016-2018 Microchip Technology Inc. DS40001866B-page 275


PIC16(L)F15356/75/76/85/86
20.3 ADC Acquisition Requirements source impedance is decreased, the acquisition time
may be decreased. After the analog input channel is
For the ADC to meet its specified accuracy, the charge selected (or changed), an ADC acquisition must be
holding capacitor (CHOLD) must be allowed to fully done before the conversion can be started. To calculate
charge to the input channel voltage level. The Analog the minimum acquisition time, Equation 20-1 may be
Input model is shown in Figure 20-4. The source used. This equation assumes that 1/2 LSb error is used
impedance (RS) and the internal sampling switch (RSS) (1024 steps for the ADC). The 1/2 LSb error is the
impedance directly affect the time required to charge maximum error allowed for the ADC to meet its
the capacitor CHOLD. The sampling switch (RSS) specified resolution.
impedance varies over the device voltage (VDD), refer
to Figure 20-4. The maximum recommended
impedance for analog sources is 10 k. As the

EQUATION 20-1: ACQUISITION TIME EXAMPLE

Assumptions: Temperature = 50°C and external impedance of 10k  5.0V V DD

T ACQ = Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient
= T AMP + T C + T COFF
= 2µs + T C +   Temperature - 25°C   0.05µs/°C  

The value for TC can be approximated with the following equations:

1
V APPLIED  1 – -------------------------- = V CHOLD ;[1] VCHOLD charged to within 1/2 lsb
n+1
2 –1
–T C
 ----------
RC
V APPLIED  1 – e  = V CHOLD ;[2] VCHOLD charge response to VAPPLIED
 
– Tc
 ---------
1
V APPLIED  1 – e  = V APPLIED  1 – -------------------------- ;combining [1] and [2]
RC
   n+1 
2 –1
Note: Where n = number of bits of the ADC.

Solving for TC:

T C = – C HOLD  R IC + R SS + R S  ln(1/2047)
= – 10pF  1k  + 7k  + 10k   ln(0.0004885)
= 1.37 µs
Therefore:
T ACQ = 2µs + 1.37 +   50°C- 25°C   0.05µs/°C  
= 4.62µs

Note 1: The VAPPLIED has no effect on the equation, since it cancels itself out.
2: The charge holding capacitor (CHOLD) is not discharged after each conversion.
3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin
leakage specification.

 2016-2018 Microchip Technology Inc. DS40001866B-page 276


PIC16(L)F15356/75/76/85/86
FIGURE 20-4: ANALOG INPUT MODEL

Rev. 10-000070A
8/23/2016

VDD
Sampling
Analog switch
VT § 0.6V SS
RS Input pin RIC ” 1K RSS

ILEAKAGE(1) CHOLD = 10 pF
VA CPIN VT § 0.6V
5pF
Ref-

6V
Legend: CHOLD = Sample/Hold Capacitance 5V
CPIN = Input Capacitance VDD 4V RSS
3V
ILEAKAGE = Leakage Current at the pin due to varies injunctions 2V
RIC = Interconnect Resistance
RSS = Resistance of Sampling switch
SS = Sampling Switch 5 6 7 8 9 10 11
VT = Threshold Voltage Sampling Switch
RS = Source Resistance (kŸ )

Note 1: See Refer to Section 37.0 “Electrical Specifications”.

FIGURE 20-5: ADC TRANSFER FUNCTION

Full-Scale Range

3FFh
3FEh
3FDh
3FCh
ADC Output Code

3FBh

03h
02h
01h
00h
Analog Input Voltage
0.5 LSB 1.5 LSB

Ref- Zero-Scale
Transition Full-Scale
Transition Ref+

 2016-2018 Microchip Technology Inc. DS40001866B-page 277


PIC16(L)F15356/75/76/85/86
20.4 Register Definitions: ADC Control
REGISTER 20-1: ADCON0: ADC CONTROL REGISTER 0
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CHS<5:0> GO/DONE ADON
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-2 CHS<5:0>: Analog Channel Select bits


111111 = FVR Buffer 2 reference voltage(2)
111110 = FVR 1Buffer 1 reference voltage(2)
111101 = DAC1 output voltage(1)
111100 = Temperature sensor output(3)
111011 = AVSS (Analog Ground)
111010-100000 = Reserved. No channel connected
101111 = RF7
101110 = RF6
101101 = RF5
101100 = RF4
101011 = RF3
101010 = RF2
101001 = RF1
101000 = RF0
100010 = RE2
100001 = RE1
100000 = RE0
011111 = RD7
011110 = RD6
011101 = RD5
011100 = RD4
011011 = RD3
011010 = RD2
011001 = RD1
011000 = RD0
010111 = RC7
010110 = RC6
010101 = RC5
010100 = RC4
010011 = RC3
010010 = RC2
010001 = RC1
010000 = RC0
001111 = RB7
001110 = RB6
001101 = RB5
001100 = RB4
001011 = RB3
001010 = RB2
001001 = RB1
001000 = RB0
000111 = RA7(4)
000110 = RA6(4)
000101 = RA5
000100 = RA4
000011 = RA3
000010 = RA2
000001 = RA1
000000 = RA0

 2016-2018 Microchip Technology Inc. DS40001866B-page 278


PIC16(L)F15356/75/76/85/86
REGISTER 20-1: ADCON0: ADC CONTROL REGISTER 0 (CONTINUED)
bit 1 GO/DONE: ADC Conversion Status bit
1 = ADC conversion cycle in progress. Setting this bit starts an ADC conversion cycle.
This bit is automatically cleared by hardware when the ADC conversion has completed.
0 = ADC conversion completed/not in progress
bit 0 ADON: ADC Enable bit
1 = ADC is enabled
0 = ADC is disabled and consumes no operating current

Note 1: See Section 21.0 “5-Bit Digital-to-Analog Converter (DAC1) Module” for more information.
2: See Section 18.0 “Fixed Voltage Reference (FVR)” for more information.
3: See Section 19.0 “Temperature Indicator Module” for more information.
4: The analog channel functionality on these pins is disabled when the system clock source is selected is external.

 2016-2018 Microchip Technology Inc. DS40001866B-page 279


PIC16(L)F15356/75/76/85/86

REGISTER 20-2: ADCON1: ADC CONTROL REGISTER 1


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0
ADFM ADCS<2:0> — — ADPREF<1:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 ADFM: ADC Result Format Select bit


1 = Right justified. Six Most Significant bits of ADRESH are set to ‘0’ when the conversion result is
loaded.
0 = Left justified. Six Least Significant bits of ADRESL are set to ‘0’ when the conversion result is
loaded.
bit 6-4 ADCS<2:0>: ADC Conversion Clock Select bits
111 =ADCRC (dedicated RC oscillator)
110 =FOSC/64
101 =FOSC/16
100 =FOSC/4
011 =ADCRC (dedicated RC oscillator)
010 =FOSC/32
001 =FOSC/8
000 =FOSC/2
bit 3-2 Unimplemented: Read as ‘0’
bit 1-0 ADPREF<1:0>: ADC Positive Voltage Reference Configuration bits
11 =VREF+ is connected to internal Fixed Voltage Reference (FVR) module(1)
10 =VREF+ is connected to external VREF+ pin(1)
01 =Reserved
00 =VREF+ is connected to VDD

Note 1: When selecting the VREF+ pin as the source of the positive reference, be aware that a minimum voltage
specification exists. See Table 37-14 for details.

 2016-2018 Microchip Technology Inc. DS40001866B-page 280


PIC16(L)F15356/75/76/85/86

REGISTER 20-3: ADACT: A/D AUTO-CONVERSION TRIGGER


U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — ADACT<4:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-5 Unimplemented: Read as ‘0’


bit 4-0 ADACT<4:0>: Auto-Conversion Trigger Selection bits(1) (see Table 20-2)
Note 1: This is a rising edge sensitive input for all sources.

 2016-2018 Microchip Technology Inc. DS40001866B-page 281


PIC16(L)F15356/75/76/85/86

REGISTER 20-4: ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 0


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<9:2>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ADRES<9:2>: ADC Result Register bits


Upper eight bits of 10-bit conversion result

REGISTER 20-5: ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 0


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<1:0> — — — — — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 ADRES<1:0>: ADC Result Register bits


Lower two bits of 10-bit conversion result
bit 5-0 Reserved: Do not use.

 2016-2018 Microchip Technology Inc. DS40001866B-page 282


PIC16(L)F15356/75/76/85/86

REGISTER 20-6: ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 1


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — — — — — ADRES<9:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-2 Reserved: Do not use.


bit 1-0 ADRES<9:8>: ADC Result Register bits
Upper two bits of 10-bit conversion result

REGISTER 20-7: ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 1


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 ADRES<7:0>: ADC Result Register bits


Lower eight bits of 10-bit conversion result

 2016-2018 Microchip Technology Inc. DS40001866B-page 283


PIC16(L)F15356/75/76/85/86

TABLE 20-3: SUMMARY OF REGISTERS ASSOCIATED WITH ADC


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
INTCON GIE PEIE — — — — — INTEDG 147
PIE1 OSFIE CSWIE — — — — — ADIE 149
PIR1 OSFIF CSWIF — — — — — ADIF 157
TRISA — — TRISA5 TRISA4 — TRISA2 TRISA1 TRISA0 201
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 201
(1)
TRISB TRISB7 TRISB6 TRISB5 TRISB4 — — — — 207
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 207
TRISC TRISC7(1) TRISC6(1) TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 212
TRISD TRISD7(1) TRISD6(1) TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 217
TRISE TRISE7(1) TRISE6(1) TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0 223
TRISF TRISF7(1) TRISF6(1) TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0 229
ANSELA — — ANSA5 ANSA4 — ANSA2 ANSA1 ANSA0 202
(1)
ANSELB — — — ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 208
ANSELA ANSA7 ANSA6 ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 202
ANSELB ANSB7 ANSB6 ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 208
ANSELC ANSC7(1) ANSC6(1) ANSC5 ANSC4 ANSC3 ANSC2 ANSC1 ANSC0 213
ANSELD ANSD7(1) ANSD6(1) ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 218
ANSELE ANSE7(1) ANSE6(1) ANSE5 ANSE4 ANSE3 ANSE2 ANSE1 ANSE0 224
ANSELF ANSF7(1) ANSF6(1) ANSF5 ANSF4 ANSF3 ANSF2 ANSF1 ANSF0 230
ADCON0 CHS<5:0> GO/DONE ADON 278
ADCON1 ADFM ADCS<2:0> — — ADPREF<1:0> 280
ADACT — — — ADACT<4:0> 281
ADRESH ADRESH<7:0> 282
ADRESL ADRESL<7:0> 282
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 265
DAC1CON1 — — — DAC1R<4:0> 288
OSCSTAT1 EXTOR HFOR MFOR LFOR SOR ADOR — PLLR 138
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for the ADC module.
Note 1: Present on only.
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for the ADC module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 284


PIC16(L)F15356/75/76/85/86
21.0 5-BIT DIGITAL-TO-ANALOG 21.1 Output Voltage Selection
CONVERTER (DAC1) MODULE The DAC has 32 voltage level ranges. The 32 levels
The Digital-to-Analog Converter supplies a variable are set with the DAC1R<4:0> bits of the DAC1CON1
voltage reference, ratiometric with the input source, register.
with 32 selectable output levels. The DAC output voltage is determined by Equation 21-1:
The input of the DAC can be connected to:
• External VREF pins
• VDD supply voltage
• FVR (Fixed Voltage Reference)
The output of the DAC can be configured to supply a
reference voltage to the following:
• Comparator positive input
• ADC input channel
• DAC1OUT pin
The Digital-to-Analog Converter (DAC) is enabled by
setting the DAC1EN bit of the DAC1CON0 register.

EQUATION 21-1: DAC OUTPUT VOLTAGE


 4:0
V
OUT
=   VSOURCE+ – VSOURCE-   DAC1R
----------------------------------- +  V
5 SOURCE-

2
V = V or V or FVR
SOURCE+ DD REF+

V = V or V REF-
SOURCE- SS

21.2 Ratiometric Output Level


The DAC output value is derived using a resistor ladder
with each end of the ladder tied to a positive and
negative voltage reference input source. If the voltage
of either input source fluctuates, a similar fluctuation will
result in the DAC output value.
The value of the individual resistors within the ladder
can be found in Table 37-15.

21.3 DAC Voltage Reference Output


The DAC voltage can be output to the DAC1OUT1/2
pins by setting the DAC1OE1/2 bits of the DAC1CON0
register, respectively. Selecting the DAC reference
voltage for output on the DAC1OUT1/2 pins
automatically overrides the digital output buffer and
digital input threshold detector functions, disables the
weak pull-up, and disables the current-controlled drive
function of that pin. Reading the DAC1OUT1/2 pin
when it has been configured for DAC reference voltage
output will always return a ‘0’.
Due to the limited current drive capability, a buffer must
be used on the DAC voltage reference output for
external connections to the DAC1OUT1/2 pins.
Figure 21-2 shows an example buffering technique.

 2016-2018 Microchip Technology Inc. DS40001866B-page 285


PIC16(L)F15356/75/76/85/86
FIGURE 21-1: DIGITAL-TO-ANALOG CONVERTER BLOCK DIAGRAM
Rev. 10-000026G
12/15/2016

Reserved 11
VSOURCE+ DACR<4:0>
FVR Buffer 10 5
VREF+ 01 R

VDD 00

R
DACPSS

32-to-1 MUX
32 DACx_output
To Peripherals
Steps
DACEN
R

R DACxOUT1(1)

DACOE1
R
DACxOUT2(1)

VREF- 1 VSOURCE- DACOE2


VSS 0

DACNSS
Note 1: The unbuffered DACx_output is provided on the DACxOUT pin(s).

FIGURE 21-2: VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE

PIC® MCU

DAC
R
Module
+
Voltage DAC1OUT Buffered DAC Output

Reference
Output
Impedance

 2016-2018 Microchip Technology Inc. DS40001866B-page 286


PIC16(L)F15356/75/76/85/86
21.4 Operation During Sleep
The DAC continues to function during Sleep. When the
device wakes up from Sleep through an interrupt or a
Watchdog Timer time-out, the contents of the
DAC1CON0 register are not affected.

21.5 Effects of a Reset


A device Reset affects the following:
• DAC is disabled.
• DAC output voltage is removed from the
DAC1OUT1/2 pins.
• The DAC1R<4:0> range select bits are cleared.

 2016-2018 Microchip Technology Inc. DS40001866B-page 287


PIC16(L)F15356/75/76/85/86
21.6 Register Definitions: DAC Control

REGISTER 21-1: DAC1CON0: VOLTAGE REFERENCE CONTROL REGISTER 0


R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0
DAC1EN — DAC1OE1 DAC1OE2 DAC1PSS<1:0> — DAC1NSS
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 DAC1EN: DAC1 Enable bit


1 = DAC is enabled
0 = DAC is disabled
bit 6 Unimplemented: Read as ‘0’
bit 5 DAC1OE1: DAC1 Voltage Output 1 Enable bit
1 = DAC voltage level is an output on the DAC1OUT1 pin
0 = DAC voltage level is disconnected from the DAC1OUT1 pin
bit 4 DAC1OE2: DAC1 Voltage Output 2 Enable bit
1 = DAC voltage level is an output on the DAC1OUT2 pin
0 = DAC voltage level is disconnected from the DAC1OUT2 pin
bit 3-2 DAC1PSS<1:0>: DAC1 Positive Source Select bits
11 =Reserved, do not use
10 =FVR output
01 =VREF+ pin
00 =VDD
bit 1 Unimplemented: Read as ‘0’
bit 0 DAC1NSS: Read as ‘0’

REGISTER 21-2: DAC1CON1: VOLTAGE REFERENCE CONTROL REGISTER 1


U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — DAC1R<4:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-5 Unimplemented: Read as ‘0’


bit 4-0 DAC1R<4:0>: DAC1 Voltage Output Select bits
VOUT = (VSRC+ - VSRC-)*(DAC1R<4:0>/32) + VSRC

 2016-2018 Microchip Technology Inc. DS40001866B-page 288


PIC16(L)F15356/75/76/85/86
TABLE 21-1: SUMMARY OF REGISTERS ASSOCIATED WITH THE DAC1 MODULE
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
DAC1CON0 DAC1EN — DAC1OE1 DAC1OE2 DAC1PSS<1:0> — DAC1NSS 288
DAC1CON1 — — — DAC1R<4:0> 288
CM1PSEL — — — — — PCH<2:0> 308
CM2PSEL — — — — — PCH<2:0> 308
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used with the DAC module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 289


PIC16(L)F15356/75/76/85/86
22.0 NUMERICALLY CONTROLLED
OSCILLATOR (NCO) MODULE
The Numerically Controlled Oscillator (NCO) module is
a timer that uses overflow from the addition of an
increment value to divide the input frequency. The
advantage of the addition method over simple counter
driven timer is that the output frequency resolution
does not vary with the divider value. The NCO is most
useful for application that requires frequency accuracy
and fine resolution at a fixed duty cycle.
Features of the NCO include:
• 20-bit Increment Function
• Fixed Duty Cycle mode (FDC) mode
• Pulse Frequency (PF) mode
• Output Pulse Width Control
• Multiple Clock Input Sources
• Output Polarity Control
• Interrupt Capability
Figure 22-1 is a simplified block diagram of the NCO
module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 290


FIGURE 22-1: NUMERICALLY CONTROLLED OSCILLATOR MODULE SIMPLIFIED BLOCK DIAGRAM
 2016-2018 Microchip Technology Inc.

NCOxINCU NCOxINCH NCOxINCL Rev. 10-000028D


3/24/2017
20
(1)
INCBUFU INCBUFH INCBUFL
20
20
1111

NCO_overflow Adder
20
NCOx Clock
NCOx_clk
Sources NCOxACCU NCOxACCH NCOxACCL
20
See
NCOxCLK
Register NCO_interrupt set bit

PIC16(L)F15356/75/76/85/86
Fixed Duty NCOxIF
0000
Cycle Mode
Circuitry

NxCKS<3:0> D Q D Q 0 TRIS bit


4

NCOxOUT
_ 1
Q

NxPFM NxPOL

NCOx_out
To Peripherals

EN S Q

_ NxOUT
Ripple
R Q
Counter

Pulse
R Frequency
3
DS40001866B-page 291

Mode Circuitry
NxPWS<2:0>

Note 1: The increment registers are double-buffered to allow for value changes to be made without first disabling the NCO module. The full increment value is loaded into the buffer registers on the
second rising edge of the NCOx_clk signal that occurs immediately after a write to NCOxINCL register. The buffers are not user-accessible and are shown here for reference.
PIC16(L)F15356/75/76/85/86
22.1 NCO OPERATION
The NCO operates by repeatedly adding a fixed value to
an accumulator. Additions occur at the input clock rate.
The accumulator will overflow with a carry periodically,
which is the raw NCO output (NCO_overflow). This
effectively reduces the input clock by the ratio of the
addition value to the maximum accumulator value. See
Equation 22-1.
The NCO output can be further modified by stretching
the pulse or toggling a flip-flop. The modified NCO
output is then distributed internally to other peripherals
and can be optionally output to a pin. The accumulator
overflow also generates an interrupt (NCO_overflow).
The NCO period changes in discrete steps to create an
average frequency.

EQUATION 22-1: NCO OVERFLOW FREQUENCY

Clock Frequency  Increment Value-


F OVERFLOW = NCO
---------------------------------------------------------------------------------------------------------------
20
2

22.1.1 NCO CLOCK SOURCES 22.1.4 INCREMENT REGISTERS


Clock sources available to the NCO include: The increment value is stored in three registers making
• HFINTOSC up a 20-bit incrementer. In order of LSB to MSB they
• FOSC are:
• LC1_out • NCO1INCL
• LC2_out • NCO1INCH
• LC3_out • NCO1INCU
• LC4_out
• MFINTOSC (500 kHz) When the NCO module is enabled, the NCO1INCU and
• MFINTOSC (32 kHz) NCO1INCH registers should be written first, then the
• SOSC NCO1INCL register. Writing to the NCO1INCL register
• CLKR initiates the increment buffer registers to be loaded
simultaneously on the second rising edge of the
The NCO clock source is selected by configuring the NCO_clk signal.
N1CKS<2:0> bits in the NCO1CLK register.
The registers are readable and writable. The increment
22.1.2 ACCUMULATOR registers are double-buffered to allow value changes to
be made without first disabling the NCO module.
The accumulator is a 20-bit register. Read and write
access to the accumulator is available through three When the NCO module is disabled, the increment
registers: buffers are loaded immediately after a write to the
increment registers.
• NCO1ACCL
• NCO1ACCH
• NCO1ACCU Note: The increment buffer registers are not user-
accessible.
22.1.3 ADDER
The NCO Adder is a full adder, which operates
synchronously from the source clock. The addition of
the previous result and the increment value replaces
the accumulator value on the rising edge of each input
clock.

 2016-2018 Microchip Technology Inc. DS40001866B-page 292


PIC16(L)F15356/75/76/85/86
22.2 FIXED DUTY CYCLE MODE 22.5 Interrupts
In Fixed Duty Cycle (FDC) mode, every time the When the accumulator overflows (NCO_overflow), the
accumulator overflows (NCO_overflow), the output is NCO Interrupt Flag bit, NCO1IF, of the PIR7 register is
toggled at a frequency rate half of the FOVERFLOW. This set. To enable the interrupt event (NCO_interrupt), the
provides a 50% duty cycle, provided that the increment following bits must be set:
value remains constant. For more information, see • N1EN bit of the NCO1CON register
Figure 22-2. • NCO1IE bit of the PIE7 register
The FDC mode is selected by clearing the N1PFM bit • PEIE bit of the INTCON register
in the NCO1CON register. • GIE bit of the INTCON register
The interrupt must be cleared by software by clearing
22.3 PULSE FREQUENCY MODE the NCO1IF bit in the Interrupt Service Routine.
In Pulse Frequency (PF) mode, every time the
Accumulator overflows, the output becomes active for 22.6 Effects of a Reset
one or more clock periods. Once the clock period All of the NCO registers are cleared to zero as the
expires, the output returns to an inactive state. This result of a Reset.
provides a pulsed output. The output becomes active
on the rising clock edge immediately following the
overflow event. For more information, see Figure 22-2.
22.7 Operation in Sleep
The value of the active and inactive states depends on The NCO module operates independently from the
the polarity bit, N1POL in the NCO1CON register. system clock and will continue to run during Sleep,
provided that the clock source selected remains active.
The PF mode is selected by setting the N1PFM bit in
the NCO1CON register. The HFINTOSC remains active during Sleep when the
NCO module is enabled and the HFINTOSC is
22.3.1 OUTPUT PULSE WIDTH CONTROL selected as the clock source, regardless of the system
clock source selected.
When operating in PF mode, the active state of the out-
put can vary in width by multiple clock periods. Various In other words, if the HFINTOSC is simultaneously
pulse widths are selected with the N1PWS<2:0> bits in selected as the system clock and the NCO clock
the NCO1CLK register. source, when the NCO is enabled, the CPU will go idle
during Sleep, but the NCO will continue to operate and
When the selected pulse width is greater than the
the HFINTOSC will remain active.
Accumulator overflow time frame, then NCO1 output
does not toggle. This will have a direct effect on the Sleep mode current.

22.4 OUTPUT POLARITY CONTROL


The last stage in the NCO module is the output polarity.
The N1POL bit in the NCO1CON register selects the
output polarity. Changing the polarity while the
interrupts are enabled will cause an interrupt for the
resulting output transition.
The NCO output signal (NCO1_out) is available to the
following peripherals:
• CLC
• CWG
• Timer1
• Timer2
• CLKR

 2016-2018 Microchip Technology Inc. DS40001866B-page 293


FIGURE 22-2: FDC OUTPUT MODE OPERATION DIAGRAM
 2016-2018 Microchip Technology Inc.

Rev. 10-000029A
11/7/2013

NCOx
Clock
Source

NCOx
Increment 4000h 4000h 4000h
Value

NCOx
Accumulator 00000h 04000h 08000h FC000h 00000h 04000h 08000h FC000h 00000h 04000h 08000h
Value

PIC16(L)F15356/75/76/85/86
NCO_overflow

NCO_interrupt

NCOx Output
FDC Mode

NCOx Output
PF Mode
DS40001866B-page 294

NCOxPWS =
000

NCOx Output
PF Mode
NCOxPWS =
001
PIC16(L)F15356/75/76/85/86
22.8 NCO Control Registers

REGISTER 22-1: NCO1CON: NCO CONTROL REGISTER


R/W-0/0 U-0 R-0/0 R/W-0/0 U-0 U-0 U-0 R/W-0/0
N1EN — N1OUT N1POL — — — N1PFM
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 N1EN: NCO1 Enable bit


1 = NCO1 module is enabled
0 = NCO1 module is disabled
bit 6 Unimplemented: Read as ‘0’
bit 5 N1OUT: NCO1 Output bit
Displays the current output value of the NCO1 module.
bit 4 N1POL: NCO1 Polarity bit
1 = NCO1 output signal is inverted
0 = NCO1 output signal is not inverted
bit 3-1 Unimplemented: Read as ‘0’
bit 0 N1PFM: NCO1 Pulse Frequency Mode bit
1 = NCO1 operates in Pulse Frequency mode
0 = NCO1 operates in Fixed Duty Cycle mode, divide by 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 295


PIC16(L)F15356/75/76/85/86
REGISTER 22-2: NCO1CLK: NCO1 INPUT CLOCK CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
N1PWS<2:0>(1,2) — N1CKS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-5 N1PWS<2:0>: NCO1 Output Pulse Width Select bits(1)


111 = NCO1 output is active for 128 input clock periods
110 = NCO1 output is active for 64 input clock periods
101 = NCO1 output is active for 32 input clock periods
100 = NCO1 output is active for 16 input clock periods
011 = NCO1 output is active for 8 input clock periods
010 = NCO1 output is active for 4 input clock periods
001 = NCO1 output is active for 2 input clock periods
000 = NCO1 output is active for 1 input clock period
bit 4 Unimplemented: Read as ‘0’
bit 3-0 N1CKS<3:0>: NCO1 Clock Source Select bits
1011-1111 = Reserved
1010 = LC4_out
1001 = LC3_out
1000 = LC2_out
0111 = LC1_out
0110 = CLKR
0101 = SOSC
0100 = MFINTOSC (32 kHz)
0011 = MFINTOSC (500 kHz)
0010 = LFINTOSC
0001 = HFINTOSC
0000 = FOSC

Note 1: N1PWS applies only when operating in Pulse Frequency mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 296


PIC16(L)F15356/75/76/85/86
REGISTER 22-3: NCO1ACCL: NCO1 ACCUMULATOR REGISTER – LOW BYTE
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
NCO1ACC<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NCO1ACC<7:0>: NCO1 Accumulator, Low Byte

REGISTER 22-4: NCO1ACCH: NCO1 ACCUMULATOR REGISTER – HIGH BYTE


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
NCO1ACC<15:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NOC1ACC<15:8>: NCO1 Accumulator, High Byte

REGISTER 22-5: NCO1ACCU: NCO1 ACCUMULATOR REGISTER – UPPER BYTE(1)


U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — NCO1ACC<19:16>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 NCO1ACC<19:16>: NCO1 Accumulator, Upper Byte

Note 1: The accumulator spans registers NCO1ACCU:NCO1ACCH: NCO1ACCL. The 24 bits are reserved but
not all are used.This register updates in real-time, asynchronously to the CPU; there is no provision to
guarantee atomic access to this 24-bit space using an 8-bit bus. Writing to this register while the module is
operating will produce undefined results.

 2016-2018 Microchip Technology Inc. DS40001866B-page 297


PIC16(L)F15356/75/76/85/86
REGISTER 22-6: NCO1INCL: NCO1 INCREMENT REGISTER – LOW BYTE(1,2)
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-1/1
NCO1INC<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NCO1INC<7:0>: NCO1 Increment, Low Byte

Note 1: The logical increment spans NCO1INCU:NCO1INCH:NCO1INCL.


2: NCO1INC is double-buffered as INCBUF; INCBUF is updated on the next falling edge of NCOCLK after
writing to NCO1INCL; NCO1INCU and NCO1INCH should be written prior to writing NCO1INCL.

REGISTER 22-7: NCO1INCH: NCO1 INCREMENT REGISTER – HIGH BYTE(1)


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
NCO1INC<15:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 NCO1INC<15:8>: NCO1 Increment, High Byte

Note 1: The logical increment spans NCO1INCU:NCO1INCH:NCO1INCL.

REGISTER 22-8: NCO1INCU: NCO1 INCREMENT REGISTER – UPPER BYTE(1)


U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — NCO1INC<19:16>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 NCO1INC<19:16>: NCO1 Increment, Upper Byte

Note 1: The logical increment spans NCO1INCU:NCO1INCH:NCO1INCL.

 2016-2018 Microchip Technology Inc. DS40001866B-page 298


PIC16(L)F15356/75/76/85/86

TABLE 22-1: SUMMARY OF REGISTERS ASSOCIATED WITH NCO

Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE ― ― ― ― ― INTEDG 147


PIR7 — — NVMIF NCO1IF — — — CWG1IF 163
PIE7 — — NVMIE NCO1IE — — — CWG1IE 155
NCO1CON N1EN ― N1OUT N1POL ― ― ― N1PFM 295
NCO1CLK N1PWS<2:0> ― N1CKS<3:0> 296
NCO1ACCL NCO1ACC<7:0> 297
NCO1ACCH NCO1ACC<15:8> 297
NCO1ACCU ― ― ― ― NCO1ACC<19:16> 297
NCO1INCL NCO1INC<7:0> 298
NCO1INCH NCO1INC<15:8> 298
NCO1INCU ― ― ― ― NCO1AINC<19:16> 298
RxyPPS ― ― ― RxyPPS<4:0> 243
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for NCO module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 299


PIC16(L)F15356/75/76/85/86
23.0 COMPARATOR MODULE FIGURE 23-1: SINGLE COMPARATOR
Comparators are used to interface analog circuits to a
digital circuit by comparing two analog voltages and VIN+ +
providing a digital indication of their relative magnitudes. Output
VIN- –
Comparators are very useful mixed signal building
blocks because they provide analog functionality
independent of program execution. The analog
comparator module includes the following features:
• Programmable input selection VIN-
VIN+
• Selectable voltage reference
• Programmable output polarity
• Rising/falling output edge interrupts
• CWG1 Auto-shutdown source
Output
23.1 Comparator Overview
A single comparator is shown in Figure 23-1 along with
Note: The black areas of the output of the
the relationship between the analog input levels and
comparator represents the uncertainty
the digital output. When the analog voltage at VIN+ is
due to input offsets and response time.
less than the analog voltage at VIN-, the output of the
comparator is a digital low level. When the analog
voltage at VIN+ is greater than the analog voltage at
VIN-, the output of the comparator is a digital high level.
The comparators available are shown in Table 23-1.

TABLE 23-1: AVAILABLE COMPARATORS


Device C1 C2
PIC16(L)F15356/75/76/85/86 ● ●

 2016-2018 Microchip Technology Inc. DS40001866B-page 300


PIC16(L)F15356/75/76/85/86
FIGURE 23-2: COMPARATOR MODULE SIMPLIFIED BLOCK DIAGRAM

Rev. 10-000027K
11/20/2015

3 (1)
CxNCH<2:0> CxON
Interrupt CxINTP
Rising
Edge set bit
CxIN0- 000 CxIF
Interrupt CxINTN
CxIN1- 001
Falling
CxIN2- 010 CxON(1) Edge

CxIN3- 011 CxVN


- D Q
CxOUT
Reserved 100
Cx MCxOUT
Reserved 101 CxVP
FVR_buffer2 110
+ Q1

111 CxSP CxHYS CxPOL

CxOUT_sync to
peripherals
CxSYNC
CxIN0+ 000
TRIS bit
CxIN1+ 001 0

Reserved 010 PPS CxOUT


D Q 1
Reserved 011
Reserved 100 RxyPPS
(From Timer1 Module) T1CLK
DAC_output 101
FVR_buffer2 110
111

CxPCH<2:0> CxON(1)
2

Note 1: When CxON = 0, all multiplexer inputs are disconnected and the Comparator will produce a ‘0’ at the output.

 2016-2018 Microchip Technology Inc. DS40001866B-page 301


PIC16(L)F15356/75/76/85/86
23.2 Comparator Control 23.2.3 COMPARATOR OUTPUT POLARITY
Each comparator has two control registers: CMxCON0 Inverting the output of the comparator is functionally
and CMxCON1. equivalent to swapping the comparator inputs. The
polarity of the comparator output can be inverted by
The CMxCON0 register (see Register 23-1) contains setting the CxPOL bit of the CMxCON0 register.
Control and Status bits for the following: Clearing the CxPOL bit results in a non-inverted output.
• Enable Table 23-2 shows the output state versus input
• Output conditions, including polarity control.
• Output polarity
• Hysteresis enable
TABLE 23-2: COMPARATOR OUTPUT
• Timer1 output synchronization STATE VS. INPUT
The CMxCON1 register (see Register 23-2) contains CONDITIONS
Control bits for the following:
Input Condition CxPOL CxOUT
• Interrupt on positive/negative edge enables
CxVN > CxVP 0 0
23.2.1 COMPARATOR ENABLE CxVN < CxVP 0 1
Setting the CxON bit of the CMxCON0 register enables CxVN > CxVP 1 1
the comparator for operation. Clearing the CxON bit CxVN < CxVP 1 0
disables the comparator resulting in minimum current
consumption.

23.2.2 COMPARATOR OUTPUT


The output of the comparator can be monitored by
reading either the CxOUT bit of the CMxCON0 register
or the MCxOUT bit of the CMOUT register.
The comparator output can also be routed to an
external pin through the RxyPPS register (Register 15-
2). The corresponding TRIS bit must be clear to enable
the pin as an output.
Note 1: The internal output of the comparator is
latched with each instruction cycle.
Unless otherwise specified, external out-
puts are not latched.

 2016-2018 Microchip Technology Inc. DS40001866B-page 302


PIC16(L)F15356/75/76/85/86
23.3 Comparator Hysteresis The associated interrupt flag bit, CxIF bit of the PIR2
register, must be cleared in software. If another edge is
A selectable amount of separation voltage can be detected while this flag is being cleared, the flag will still
added to the input pins of each comparator to provide a be set at the end of the sequence.
hysteresis function to the overall operation. Hysteresis
is enabled by setting the CxHYS bit of the CMxCON0
register.
Note: Although a comparator is disabled, an
See Comparator Specifications in Table 37-14 for more interrupt can be generated by changing
information. the output polarity with the CxPOL bit of
the CMxCON0 register, or by switching
23.4 Timer1 Gate Operation the comparator on or off with the CxON bit
of the CMxCON0 register.
The output resulting from a comparator operation can
be used as a source for gate control of Timer1. See
Section 26.6 “Timer Gate” for more information. This 23.6 Comparator Positive Input
feature is useful for timing the duration or interval of an Selection
analog event.
Configuring the CxPCH<2:0> bits of the CMxPCH
It is recommended that the comparator output be register directs an internal voltage reference or an
synchronized to Timer1. This ensures that Timer1 does analog pin to the noninverting input of the comparator:
not increment while a change in the comparator is
occurring. • CxIN0+ analog pin
• DAC output
23.4.1 COMPARATOR OUTPUT • FVR (Fixed Voltage Reference)
SYNCHRONIZATION • VSS (Ground)
The output from a comparator can be synchronized See Section 18.0 “Fixed Voltage Reference (FVR)”
with Timer1 by setting the CxSYNC bit of the for more information on the Fixed Voltage Reference
CMxCON0 register. module.
Once enabled, the comparator output is latched on the See Section 21.0 “5-Bit Digital-to-Analog Converter
falling edge of the Timer1 source clock. If a prescaler is (DAC1) Module” for more information on the DAC
used with Timer1, the comparator output is latched after input signal.
the prescaling function. To prevent a race condition, the
Any time the comparator is disabled (CxON = 0), all
comparator output is latched on the falling edge of the
comparator inputs are disabled.
Timer1 clock source and Timer1 increments on the
rising edge of its clock source. See the Comparator
Block Diagram (Figure 23-2) and the Timer1 Block 23.7 Comparator Negative Input
Diagram (Figure 26-1) for more information. Selection
The CxNCH<2:0> bits of the CMxNCH register direct
23.5 Comparator Interrupt an analog input pin and internal reference voltage or
An interrupt can be generated upon a change in the analog ground to the inverting input of the comparator:
output value of the comparator for each comparator, a • CxINy - pin
rising edge detector and a falling edge detector are • FVR (Fixed Voltage Reference)
present.
• Analog Ground
When either edge detector is triggered and its associ-
ated enable bit is set (CxINTP and/or CxINTN bits of
the CMxCON1 register), the Corresponding Interrupt
Note: To use CxINy+ and CxINy- pins as analog
Flag bit (CxIF bit of the PIR2 register) will be set.
input, the appropriate bits must be set in
To enable the interrupt, you must set the following bits: the ANSEL register and the correspond-
• CxON, CxPOL and CxSP bits of the CMxCON0 ing TRIS bits must also be set to disable
register the output drivers.
• CxIE bit of the PIE2 register
• CxINTP bit of the CMxCON1 register (for a rising
edge detection)
• CxINTN bit of the CMxCON1 register (for a falling
edge detection)
• PEIE and GIE bits of the INTCON register

 2016-2018 Microchip Technology Inc. DS40001866B-page 303


PIC16(L)F15356/75/76/85/86
23.8 Comparator Response Time 23.9 Analog Input Connection
The comparator output is indeterminate for a period of
Considerations
time after the change of an input source or the selection A simplified circuit for an analog input is shown in
of a new reference voltage. This period is referred to as Figure 23-3. Since the analog input pins share their
the response time. The response time of the comparator connection with a digital input, they have reverse
differs from the settling time of the voltage reference. biased ESD protection diodes to VDD and VSS. The
Therefore, both of these times must be considered when analog input, therefore, must be between VSS and VDD.
determining the total response time to a comparator If the input voltage deviates from this range by more
input change. See the Comparator and Voltage than 0.6V in either direction, one of the diodes is
Reference Specifications in Table 37-14 for more forward biased and a latch-up may occur.
details.
A maximum source impedance of 10 k is recommended
for the analog sources. Also, any external component
connected to an analog input pin, such as a capacitor or
a Zener diode, should have very little leakage current to
minimize inaccuracies introduced.

Note 1: When reading a PORT register, all pins


configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert as an analog input, according to
the input specification.
2: Analog levels on any pin defined as a
digital input, may cause the input buffer to
consume more current than is specified.

FIGURE 23-3: ANALOG INPUT MODEL


VDD
Analog
Input
pin VT  0.6V RIC
Rs < 10K
To Comparator

CPIN ILEAKAGE(1)
VA VT  0.6V
5 pF

Vss

Legend: CPIN = Input Capacitance


ILEAKAGE = Leakage Current at the pin due to various junctions
RIC = Interconnect Resistance
RS = Source Impedance
VA = Analog Voltage
VT = Threshold Voltage

Note 1: See I/O Ports in Table 37-4.

 2016-2018 Microchip Technology Inc. DS40001866B-page 304


PIC16(L)F15356/75/76/85/86
23.10 CWG1 Auto-shutdown Source
The output of the comparator module can be used as
an auto-shutdown source for the CWG1 module. When
the output of the comparator is active and the
corresponding ASxE is enabled, the CWG operation
will be suspended immediately (see Section 30.10
“Auto-Shutdown”).

23.11 Operation in Sleep Mode


The comparator module can operate during Sleep. The
comparator clock source is based on the Timer1 clock
source. If the Timer1 clock source is either the system
clock (FOSC) or the instruction clock (FOSC/4), Timer1
will not operate during Sleep, and synchronized
comparator outputs will not operate.
A comparator interrupt will wake the device from Sleep.
The CxIE bits of the PIE2 register must be set to enable
comparator interrupts.

 2016-2018 Microchip Technology Inc. DS40001866B-page 305


PIC16(L)F15356/75/76/85/86
23.12 Register Definitions: Comparator Control

REGISTER 23-1: CMxCON0: COMPARATOR Cx CONTROL REGISTER 0


R/W-0/0 R-0/0 U-0 R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0
ON OUT — POL — — HYS SYNC
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 ON: Comparator Enable bit


1 = Comparator is enabled
0 = Comparator is disabled and consumes no active power
bit 6 OUT: Comparator Output bit
If CxPOL = 1 (inverted polarity):
1 = CxVP < CxVN
0 = CxVP > CxVN
If CxPOL = 0 (noninverted polarity):
1 = CxVP > CxVN
0 = CxVP < CxVN
bit 5 Unimplemented: Read as ‘0’
bit 4 POL: Comparator Output Polarity Select bit
1 = Comparator output is inverted
0 = Comparator output is not inverted
bit 3-2 Unimplemented: Read as ‘0’
bit 1 HYS: Comparator Hysteresis Enable bit
1 = Comparator hysteresis enabled
0 = Comparator hysteresis disabled
bit 0 SYNC: Comparator Output Synchronous Mode bit
1 = Comparator output to Timer1 and I/O pin is synchronous to changes on Timer1 clock source.
Output updated on the falling edge of Timer1 clock source.
0 = Comparator output to Timer1 and I/O pin is asynchronous

 2016-2018 Microchip Technology Inc. DS40001866B-page 306


PIC16(L)F15356/75/76/85/86

REGISTER 23-2: CMxCON1: COMPARATOR Cx CONTROL REGISTER 1


U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
— — — — — — INTP INTN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-2 Unimplemented: Read as ‘0’


bit 1 INTP: Comparator Interrupt on Positive-Going Edge Enable bits
1 = The CxIF interrupt flag will be set upon a positive-going edge of the CxOUT bit
0 = No interrupt flag will be set on a positive-going edge of the CxOUT bit
bit 0 INTN: Comparator Interrupt on Negative-Going Edge Enable bits
1 = The CxIF interrupt flag will be set upon a negative-going edge of the CxOUT bit
0 = No interrupt flag will be set on a negative-going edge of the CxOUT bit

 2016-2018 Microchip Technology Inc. DS40001866B-page 307


PIC16(L)F15356/75/76/85/86

REGISTER 23-3: CMxNCH: COMPARATOR Cx NEGATIVE INPUT SELECT REGISTER


U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — — NCH<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 NCH<2:0>: Comparator Negative Input Channel Select bits
111 =CxVN connects to AVSS
110 =CxVN connects to FVR Buffer 2
101 =CxVN unconnected
100 =CxVN unconnected
011 =CxVN connects to CxIN3- pin
010 =CxVN connects to CxIN2- pin
001 =CxVN connects to CxIN1- pin
000 =CxVN connects to CxIN0- pin

REGISTER 23-4: CMxPCH: COMPARATOR Cx POSITIVE INPUT SELECT REGISTER


U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — — PCH<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 PCH<2:0>: Comparator Positive Input Channel Select bits
111 =CxVP connects to AVSS
110 =CxVP connects to FVR Buffer 2
101 =CxVP connects to DAC output
100 =CxVP unconnected
011 =CxVP unconnected
010 =CxVP unconnected
001 =CxVP connects to CxIN1+ pin
000 =CxVP connects to CxIN0+ pin

 2016-2018 Microchip Technology Inc. DS40001866B-page 308


PIC16(L)F15356/75/76/85/86

REGISTER 23-5: CMOUT: COMPARATOR OUTPUT REGISTER


U-0 U-0 U-0 U-0 U-0 U-0 R-0/0 R-0/0
— — — — — — MC2OUT MC1OUT
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-2 Unimplemented: Read as ‘0’


bit 1 MC2OUT: Mirror Copy of C2OUT bit
bit 0 MC1OUT: Mirror Copy of C1OUT bit

TABLE 23-3: SUMMARY OF REGISTERS ASSOCIATED WITH COMPARATOR MODULE


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

CMxCON0 ON OUT — POL — — HYS SYNC 306


CMxCON1 — — — — — — INTP INTN 307
CMOUT — — — — — — MC2OUT MC1OUT 309
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 265
DAC1CON0 DAC1EN — DAC1OE1 DAC1OE2 DAC1PSS<1:0> — DAC1NSS 288
DAC1CON1 — — — DAC1R<4:0> 288
INTCON GIE PEIE — INTEDG 147
PIE2 — ZCDIE — — — — C2IE C1IE 150
PIR2 — ZCDIF — — — — C2IF C1IF 158
RxyPPS ― ― ― RxyPPS<4:0> 243
CLCINxPPS — — CLCIN0PPS<5:0> 242
T1GPPS ― ― T1GPPS<5:0> 242
Legend: — = unimplemented location, read as ‘0’. Shaded cells are unused by the comparator module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 309


PIC16(L)F15356/75/76/85/86
24.0 ZERO-CROSS DETECTION 24.1 External Resistor Selection
(ZCD) MODULE The ZCD module requires a current limiting resistor in
The ZCD module detects when an A/C signal crosses series with the external voltage source. The impedance
through the ground potential. The actual zero crossing and rating of this resistor depends on the external
threshold is the zero crossing reference voltage, source peak voltage. Select a resistor value that will drop
VCPINV, which is typically 0.75V above ground. all of the peak voltage when the current through the
resistor is nominally 300 A. Refer to Equation 24-1 and
The connection to the signal to be detected is through Figure 24-1. Make sure that the ZCD I/O pin internal
a series current limiting resistor. The module applies a weak pull-up is disabled so it does not interfere with the
current source or sink to the ZCD pin to maintain a current source and sink.
constant voltage on the pin, thereby preventing the pin
voltage from forward biasing the ESD protection
EQUATION 24-1: EXTERNAL RESISTOR
diodes. When the applied voltage is greater than the
reference voltage, the module sinks current. When the
applied voltage is less than the reference voltage, the
V PEAK-
R SERIES = ----------------
–4
module sources current. The current source and sink 3 10
action keeps the pin voltage constant over the full
range of the applied voltage. The ZCD module is
shown in the simplified block diagram Figure 24-2.
FIGURE 24-1: EXTERNAL VOLTAGE
The ZCD module is useful when monitoring an A/C
waveform for, but not limited to, the following purposes: VMAXPEAK
• A/C period measurement VPEAK VMINPEAK
• Accurate long term time measurement
• Dimmer phase delayed drive
VCPINV
• Low EMI cycle switching

 2016-2018 Microchip Technology Inc. DS40001866B-page 310


PIC16(L)F15356/75/76/85/86
FIGURE 24-2: SIMPLIFIED ZCD BLOCK DIAGRAM

VPULLUP Rev. 10-000194D


6/10/2016

optional

VDD RPULLUP

- ZCDxIN RSERIES

External
Zcpinv + RPULLDOWN voltage
source

optional

ZCD Output for other modules

ZCDxPOL

ZCDxOUT pin

Interrupt
det
ZCDxINTP Set
ZCDxIF
ZCDxINTN flag
Interrupt
det

 2016-2018 Microchip Technology Inc. DS40001866B-page 311


PIC16(L)F15356/75/76/85/86
24.2 ZCD Logic Output 24.5 Correcting for VCPINV offset
The ZCD module includes a Status bit, which can be The actual voltage at which the ZCD switches is the
read to determine whether the current source or sink is reference voltage at the noninverting input of the ZCD
active. The OUT bit of the ZCDxCON register is set op amp. For external voltage source waveforms other
when the current sink is active, and cleared when the than square waves, this voltage offset from zero
current source is active. The OUT bit is affected by the causes the zero-cross event to occur either too early or
polarity even if the module is disabled. too late.

24.3 ZCD Logic Polarity 24.5.1 CORRECTION BY AC COUPLING


When the external voltage source is sinusoidal then the
The POL bit of the ZCDxCON register inverts the
effects of the VCPINV offset can be eliminated by isolat-
ZCDxOUT bit relative to the current source and sink
ing the external voltage source from the ZCD pin with a
output. When the POL bit is set, a logic '1' on the OUT
capacitor in addition to the voltage reducing resistor.
bit indicates that the current source is active, and a
The capacitor will cause a phase shift resulting in the
logic '0' on the OUT bit indicates that the current sink is
ZCD output switch in advance of the actual zero cross-
active. When the POL bit is clear, a logic '1' on the OUT
ing event. The phase shift will be the same for both ris-
bit indicates that the current sink is active, and a logic
ing and falling zero crossings, which can be
'0' on the OUT bit indicates that the current source is
compensated for by either delaying the CPU response
active.
to the ZCD switch by a timer or other means, or select-
The POL bit affects the ZCD interrupts. See ing a capacitor value large enough that the phase shift
Section 24.4 “ZCD Interrupts”. is negligible.
To determine the series resistor and capacitor values
24.4 ZCD Interrupts for this configuration, start by computing the imped-
An interrupt will be generated upon a change in the ance, Z, to obtain a peak current of 300 uA. Next, arbi-
ZCD logic output when the appropriate interrupt trarily select a suitably large non-polar capacitor and
enables are set. A rising edge detector and a falling compute its reactance, Xc, at the external voltage
edge detector are present in the ZCD for this purpose. source frequency. Finally, compute the series resistor,
capacitor peak voltage, and phase shift by the formulas
The ZCDIF bit of the PIR2 register will be set when shown in Equation 24-2.
either edge detector is triggered and its associated
enable bit is set. The INTP enables rising edge inter-
EQUATION 24-2: R-C CALCULATIONS
rupts and the INTN bit enables falling edge interrupts.
Both are located in the ZCDxCON register. VPEAK = external voltage source peak voltage
To fully enable the interrupt, the following bits must be set: f = external voltage source frequency
• ZCDIE bit of the PIE2 register C = series capacitor
• INTP bit of the ZCDxCON register R = series resistor
(for a rising edge detection)
VC = Peak capacitor voltage
• INTN bit of the ZCDxCON register
(for a falling edge detection)  = Capacitor induced zero crossing phase advance
in radians
• PEIE and GIE bits of the INTCON register
T = Time ZC event occurs before actual zero
Changing the POL bit can cause an interrupt,
crossing
regardless of the level of the EN bit.
Z = VPEAK/3x10-4
The ZCDIF bit of the PIR2 register must be cleared in
software as part of the interrupt service. If another edge Xc = 1/(2fC)
is detected while this flag is being cleared, the flag will R =  (Z2 - Xc2)
still be set at the end of the sequence.
VC = Xc(3x10-4)
 = Tan-1(Xc/R)
T = /(2f)

 2016-2018 Microchip Technology Inc. DS40001866B-page 312


PIC16(L)F15356/75/76/85/86
EXAMPLE 24-1: This offset time can be compensated for by adding a
pull-up or pull-down biasing resistor to the ZCD pin. A
VRMS = 120 pull-up resistor is used when the external voltage
VPEAK =VRMS*  source is varying relative to VSS. A pull-down resistor is
f = 60 Hz used when the voltage is varying relative to VDD. The
resistor adds a bias to the ZCD pin so that the target
C = 0.1 uF external voltage source must go to zero to pull the pin
Z = VPEAK/3x10-4 = 169.7/(3x10-4) = 565.7 kOhms voltage to the VCPINV switching voltage. The pull-up or
pull-down value can be determined with the equation
Xc = 1/(2fC) = 1/(2*60*1*10-7) = 26.53 kOhms
shown in Equation 24-4.
R =  (Z2 - Xc2) = 565.1 kOhms (computed)
R = 560 kOhms (used) EQUATION 24-4: ZCD PULL-UP/DOWN
ZR =  (R2 + Xc2) = 560.6 kOhms (using actual resis-
tor)
IPEAK = VPEAK/ ZR = 302.7*10-6 When External Signal is relative to Vss:
VC = Xc* IPEAK = 8.0 V
 = Tan-1(Xc/R) = 0.047 radians R SERIES  V PULLUP – V cpinv 
R PULLUP = ------------------------------------------------------------------------
T = /(2f) = 125.6 us
V cpinv
When External Signal is relative to VDD:
·
24.5.2 CORRECTION BY OFFSET  R PULLDOWN = R SERIES   Vcpinv 
--------------------------------------------------
CURRENT   V DD – Vcpinv  
When the waveform is varying relative to VSS, then the
zero cross is detected too early as the waveform falls
and too late as the waveform rises. When the
waveform is varying relative to VDD, then the zero cross 24.6 Handling VPEAK variations
is detected too late as the waveform rises and too early
as the waveform falls. The actual offset time can be If the peak amplitude of the external voltage is
determined for sinusoidal waveforms with the expected to vary, the series resistor must be selected
corresponding equations shown in Equation 24-3. to keep the ZCD current source and sink below the
design maximum range of ± 600 A and above a
EQUATION 24-3: ZCD EVENT OFFSET reasonable minimum range. A general rule of thumb is
that the maximum peak voltage can be no more than
When External Voltage Source is relative to Vss: six times the minimum peak voltage. To ensure that the
maximum current does not exceed ± 600 A and the
Vcpinv minimum is at least ± 100 A, compute the series
asin  ------------------ resistance as shown in Equation 24-5. The
 V PEAK 
T OFFSET = ---------------------------------- compensating pull-up for this series resistance can be
2  Freq determined with Equation 24-4 because the pull-up
value is not dependent from the peak voltage.
When External Voltage Source is relative to VDD:
EQUATION 24-5: SERIES R FOR V RANGE
V DD – Vcpinv
asin  -------------------------------- V MAXPEAK + V MINPEAK
 V PEAK  R SERIES = ---------------------------------------------------------
T OFFSET = ------------------------------------------------- –4
2  Freq 7 10

 2016-2018 Microchip Technology Inc. DS40001866B-page 313


PIC16(L)F15356/75/76/85/86
24.7 Operation During Sleep
The ZCD current sources and interrupts are unaffected
by Sleep.

24.8 Effects of a Reset


The ZCD circuit can be configured to default to the active
or inactive state on Power-on-Reset (POR). When the
ZCDDIS Configuration bit is cleared, the ZCD circuit will
be active at POR. When the ZCD Configuration bit is set,
the EN bit of the ZCDxCON register must be set to
enable the ZCD module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 314


PIC16(L)F15356/75/76/85/86
24.9 Register Definitions: ZCD Control

REGISTER 24-1: ZCDCON: ZERO-CROSS DETECTION CONTROL REGISTER


R/W-q/q U-0 R-x/x R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0
SEN — OUT POL — — INTP INTN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = value depends on Configuration bits

bit 7 SEN: Zero-Cross Detection Enable bit


1 = Zero-cross detect is enabled. ZCD pin is forced to output to source and sink current.
0 = Zero-cross detect is disabled. ZCD pin operates according to PPS and TRIS controls.
bit 6 Unimplemented: Read as ‘0’
bit 5 OUT: Zero-Cross Detection Logic Level bit
POL bit = 1:
1 = ZCD pin is sourcing current
0 = ZCD pin is sinking current
POL bit = 0:
1 = ZCD pin is sinking current
0 = ZCD pin is sourcing current
bit 4 POL: Zero-Cross Detection Logic Output Polarity bit
1 = ZCD logic output is inverted
0 = ZCD logic output is not inverted
bit 3-2 Unimplemented: Read as ‘0’
bit 1 INTP: Zero-Cross Positive Edge Interrupt Enable bit
1 = ZCDIF bit is set on low-to-high ZCDx_output transition
0 = ZCDIF bit is unaffected by low-to-high ZCDx_output transition
bit 0 INTN: Zero-Cross Negative Edge Interrupt Enable bit
1 = ZCDIF bit is set on high-to-low ZCDx_output transition
0 = ZCDIF bit is unaffected by high-to-low ZCDx_output transition

TABLE 24-1: SUMMARY OF REGISTERS ASSOCIATED WITH THE ZCD MODULE


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on page
PIE2 — ZCDIE — — — — C2IE C1IE 150
PIR2 — ZCDIF — — — — C2IF C1IF 158
ZCDxCON EN — OUT POL — — INTP INTN 315
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the ZCD module.

TABLE 24-2: SUMMARY OF CONFIGURATION WORD WITH THE ZCD MODULE


Register
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0
on Page

13:8 — — DEBUG STVREN PPS1WAY ZCDDIS BORV —


CONFIG2 103
7:0 BOREN <1:0> LPBOREN — — — PWRTE MCLRE
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by the ZCD module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 315


PIC16(L)F15356/75/76/85/86
25.0 TIMER0 MODULE The value of TMR0L is compared to that of the Period
buffer, a copy of TMR0H, on each clock cycle. When
The Timer0 module is an 8/16-bit timer/counter with the the two values match, the following events happen:
following features:
• TMR0_out goes high for one prescaled clock
• 16-bit timer/counter period
• 8-bit timer/counter with programmable period • TMR0L is reset
• Synchronous or asynchronous operation • The contents of TMR0H are copied to the period
• Selectable clock sources buffer
• Programmable prescaler (independent of
In 8-bit mode, the TMR0L and TMR0H registers are
Watchdog Timer)
both directly readable and writable. The TMR0L
• Programmable postscaler
register is cleared on any device Reset, while the
• Operation during Sleep mode
TMR0H register initializes at FFh.
• Interrupt on match or overflow
• Output on I/O pin (via PPS) or to other peripherals Both the prescaler and postscaler counters are cleared
on the following events:
25.1 Timer0 Operation • A write to the TMR0L register
• A write to either the T0CON0 or T0CON1
Timer0 can operate as either an 8-bit timer/counter or registers
a 16-bit timer/counter. The mode is selected with the • Any device Reset – Power-on Reset (POR),
T016BIT bit of the T0CON register. MCLR Reset, Watchdog Timer Reset (WDTR) or
• Brown-out Reset (BOR)
25.1.1 16-BIT MODE
In normal operation, TMR0 increments on the rising 25.1.3 COUNTER MODE
edge of the clock source. A 15-bit prescaler on the In Counter mode, the prescaler is normally disabled by
clock input gives several prescale options (see setting the T0CKPS bits of the T0CON1 register to
prescaler control bits, T0CKPS<3:0> in the T0CON1 ‘0000’. Each rising edge of the clock input (or the
register). output of the prescaler if the prescaler is used)
increments the counter by ‘1’.
25.1.1.1 Timer0 Reads and Writes in 16-Bit
Mode 25.1.4 TIMER MODE
TMR0H is not the actual high byte of Timer0 in 16-bit In Timer mode, the Timer0 module will increment every
mode. It is actually a buffered version of the real high instruction cycle as long as there is a valid clock signal
byte of Timer0, which is neither directly readable nor and the T0CKPS bits of the T0CON1 register
writable (see Figure 25-1). TMR0H is updated with the (Register 25-2) are set to ‘0000’. When a prescaler is
contents of the high byte of Timer0 during a read of added, the timer will increment at the rate based on the
TMR0L. This provides the ability to read all 16 bits of prescaler value.
Timer0 without having to verify that the read of the high
and low byte was valid, due to a rollover between 25.1.5 ASYNCHRONOUS MODE
successive reads of the high and low byte. When the T0ASYNC bit of the T0CON1 register is set
Similarly, a write to the high byte of Timer0 must also (T0ASYNC = ‘1’), the counter increments with each
take place through the TMR0H Buffer register. The high rising edge of the input source (or output of the
byte is updated with the contents of TMR0H when a prescaler, if used). Asynchronous mode allows the
write occurs to TMR0L. This allows all 16 bits of Timer0 counter to continue operation during Sleep mode
to be updated at once. provided that the clock also continues to operate during
Sleep.
25.1.2 8-BIT MODE
In normal operation, TMR0 increments on the rising 25.1.6 SYNCHRONOUS MODE
edge of the clock source. A 15-bit prescaler on the When the T0ASYNC bit of the T0CON1 register is clear
clock input gives several prescale options (see (T0ASYNC = 0), the counter clock is synchronized to
prescaler control bits, T0CKPS<3:0> in the T0CON1 the system oscillator (FOSC/4). When operating in
register). Synchronous mode, the counter clock frequency
cannot exceed FOSC/4.

 2016-2018 Microchip Technology Inc. DS40001866B-page 316


PIC16(L)F15356/75/76/85/86
25.2 Clock Source Selection 25.5 Operation during Sleep
The T0CS<2:0> bits of the T0CON1 register are used When operating synchronously, Timer0 will halt. When
to select the clock source for Timer0. Register 25-2 operating asynchronously, Timer0 will continue to
displays the clock source selections. increment and wake the device from Sleep (if Timer0
interrupts are enabled) provided that the input clock
25.2.1 INTERNAL CLOCK SOURCE source is active.
When the internal clock source is selected, Timer0
operates as a timer and will increment on multiples of 25.6 Timer0 Interrupts
the clock source, as determined by the Timer0
The Timer0 interrupt flag bit (TMR0IF) is set when
prescaler.
either of the following conditions occur:
25.2.2 EXTERNAL CLOCK SOURCE • 8-bit TMR0L matches the TMR0H value
When an external clock source is selected, Timer0 can • 16-bit TMR0 rolls over from ‘FFFFh’
operate as either a timer or a counter. Timer0 will When the postscaler bits (T0OUTPS<3:0>) are set to
increment on multiples of the rising edge of the external 1:1 operation (no division), the T0IF flag bit will be set
clock source, as determined by the Timer0 prescaler. with every TMR0 match or rollover. In general, the
TMR0IF flag bit will be set every T0OUTPS +1 matches
25.3 Programmable Prescaler or rollovers.
If Timer0 interrupts are enabled (TMR0IE bit of the
A software programmable prescaler is available for
PIE0 register = 1), the CPU will be interrupted and the
exclusive use with Timer0. There are 16 prescaler
device may wake from sleep (see Section 25.2 “Clock
options for Timer0 ranging in powers of two from 1:1 to
Source Selection” for more details).
1:32768. The prescaler values are selected using the
T0CKPS<3:0> bits of the T0CON1 register.
25.7 Timer0 Output
The prescaler is not directly readable or writable.
Clearing the prescaler register can be done by writing The Timer0 output can be routed to any I/O pin via the
to the TMR0L register or the T0CON1 register. RxyPPS output selection register (see Section 15.0
“Peripheral Pin Select (PPS) Module” for additional
25.4 Programmable Postscaler information). The Timer0 output can also be used by
other peripherals, such as the Auto-conversion Trigger
A software programmable postscaler (output divider) is of the Analog-to-Digital Converter. Finally, the Timer0
available for exclusive use with Timer0. There are 16 output can be monitored through software via the
postscaler options for Timer0 ranging from 1:1 to 1:16. Timer0 output bit (T0OUT) of the T0CON0 register
The postscaler values are selected using the (Register 25-1).
T0OUTPS<3:0> bits of the T0CON0 register.
TMR0_out will be one postscaled clock period when a
The postscaler is not directly readable or writable. match occurs between TMR0L and TMR0H in 8-bit
Clearing the postscaler register can be done by writing mode, or when TMR0 rolls over in 16-bit mode. The
to the TMR0L register or the T0CON0 register. Timer0 output is a 50% duty cycle that toggles on each
In the 16-bit mode, if the postscaler option is selected TMR0_out rising clock edge.
to a ratio other than 1:1, the reload of the TMR0H and
TMR0L registers is not possible inside the Interrupt
Service Routine. The timer period must be calculated
with the prescaler and postscaler factors selected.

 2016-2018 Microchip Technology Inc. DS40001866B-page 317


PIC16(L)F15356/75/76/85/86

FIGURE 25-1: BLOCK DIAGRAM OF TIMER0

Rev. 10-000017D
4/6/2017

CLC1 111
SOSC 110
MFINTOSC 101 T0CKPS<3:0> TMR0 Peripherals
LFINTOSC 100 body T0OUTPS<3:0> T0IF
Prescaler 1
HFINTOSC 011 IN OUT Postscaler T0_out
SYNC 0
FOSC/4 010
PPS 001 FOSC/4 T016BIT TMR0
T0ASYNC D Q PPS
000
T0CKIPPS CK Q RxyPPS

T0CS<2:0>

8-bit TMR0 Body Diagram (T016BIT = 0) 16-bit TMR0 Body Diagram (T016BIT = 1)

Clear IN TMR0 High OUT


IN TMR0L R TMR0L Byte

Read TMR0L
COMPARATOR OUT
Write TMR0L
T0_match 8
8 TMR0H
TMR0 High
Byte
Latch 8
Enable
TMR0H
8
Internal Data Bus

 2016-2018 Microchip Technology Inc. DS40001866B-page 318


PIC16(L)F15356/75/76/85/86
25.8 Register Definitions: Timer0 Control

REGISTER 25-1: T0CON0: TIMER0 CONTROL REGISTER 0


R/W-0/0 U-0 R-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
T0EN — T0OUT T016BIT T0OUTPS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 T0EN: Timer0 Enable bit


1 = The module is enabled and operating
0 = The module is disabled and in the lowest power mode
bit 6 Unimplemented: Read as ‘0’
bit 5 T0OUT: Timer0 Output bit (read-only)
Timer0 output bit
bit 4 T016BIT: Timer0 Operating as 16-bit Timer Select bit
1 = Timer0 is a 16-bit timer
0 = Timer0 is an 8-bit timer
bit 3-0 T0OUTPS<3:0>: Timer0 output postscaler (divider) select bits
1111 = 1:16 Postscaler
1110 = 1:15 Postscaler
1101 = 1:14 Postscaler
1100 = 1:13 Postscaler
1011 = 1:12 Postscaler
1010 = 1:11 Postscaler
1001 = 1:10 Postscaler
1000 = 1:9 Postscaler
0111 = 1:8 Postscaler
0110 = 1:7 Postscaler
0101 = 1:6 Postscaler
0100 = 1:5 Postscaler
0011 = 1:4 Postscaler
0010 = 1:3 Postscaler
0001 = 1:2 Postscaler
0000 = 1:1 Postscaler

 2016-2018 Microchip Technology Inc. DS40001866B-page 319


PIC16(L)F15356/75/76/85/86
REGISTER 25-2: T0CON1: TIMER0 CONTROL REGISTER 1
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
T0CS<2:0> T0ASYNC T0CKPS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-5 T0CS<2:0>: Timer0 Clock Source select bits


111 = LC1_out
110 = SOSC
101 = MFINTOSC (500 kHz)
100 = LFINTOSC
011 = HFINTOSC
010 = FOSC/4
001 = T0CKIPPS (Inverted)
000 = T0CKIPPS (True)
bit 4 T0ASYNC: TMR0 Input Asynchronization Enable bit
1 = The input to the TMR0 counter is not synchronized to system clocks
0 = The input to the TMR0 counter is synchronized to FOSC/4
bit 3-0 T0CKPS<3:0>: Prescaler Rate Select bit
1111 = 1:32768
1110 = 1:16384
1101 = 1:8192
1100 = 1:4096
1011 = 1:2048
1010 = 1:1024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1

 2016-2018 Microchip Technology Inc. DS40001866B-page 320


PIC16(L)F15356/75/76/85/86

TABLE 25-1: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER0

Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

TMR0L Holding Register for the Least Significant Byte of the 16-bit TMR0 Register 316*
TMR0H Holding Register for the Most Significant Byte of the 16-bit TMR0 Register 316*
T0CON0 T0EN ― T0OUT T016BIT T0OUTPS<3:0> 319
T0CON1 T0CS<2:0> T0ASYNC T0CKPS<3:0> 320
T0CKIPPS ― ― T0CKIPPS<5:0> 242
TMR0PPS ― ― TMR0PPS<5:0> 242
T1GCON GE GPOL GTM GSPM GGO/DONE GVAL — — 332
INTCON GIE PEIE ― ― ― ― ― INTEDG 147
PIR0 ― ― TMR0IF IOCIF ― ― ― INTF 156
PIE0 ― ― TMR0IE IOCIE ― ― ― INTE 148
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the Timer0 module.
* Page with Register information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 321


PIC16(L)F15356/75/76/85/86
26.0 TIMER1 MODULE WITH GATE • Wake-up on overflow (external clock,
Asynchronous mode only)
CONTROL
• Time base for the Capture/Compare function
The Timer1 module is 16-bit timer/counters with the • Auto-conversion Trigger (with CCP)
following features:
• Selectable Gate Source Polarity
• 16-bit timer/counter register pair (TMR1H:TMR1L) • Gate Toggle mode
• Programmable internal or external clock source • Gate Single-Pulse mode
• 2-bit prescaler • Gate Value Status
• Clock source for optional comparator • Gate Event Interrupt
synchronization
Figure 26-1 is a block diagram of the Timer1 module.
• Multiple Timer1 gate (count enable) sources
• Interrupt on overflow This device has one instance of Timer1 type modules.

FIGURE 26-1: TIMER1 BLOCK DIAGRAM


TMRxGATE<4:0> Rev. 10-000018J
8/15/2016

4
TxGPPS
TxGSPM
PPS 00000

1
0 Single Pulse D Q TxGVAL
NOTE (5) 0
11111
1 Acq. Control
Q1
D Q

TxGPOL TxGGO/DONE
CK Q
TMRxON Interrupt
set bit
R
TxGTM det TMRxGIF

TMRxGE
set flag bit
TMRxIF
TMRxON
EN
(2) To Comparators (6)
TMRx
Tx_overflow Synchronized Clock Input
TMRxH TMRxL Q D 0
1
TxCLK
TxSYNC

TMRxCLK<3:0>
4
TxCKIPPS
(1)
PPS 0000

Prescaler
Synchronize(3)
1,2,4,8
(4)
Note det
1111
2
Fosc/2
TxCKPS<1:0> Internal Sleep
Clock Input
Note 1: ST Buffer is high speed type when using TxCKIPPS.
2: TMRx register increments on rising edge.
3: Synchronize does not operate while in Sleep.
4: See Register 26-3 for Clock source selections.
5: See Register 26-4 for GATE source selections.
6: Synchronized comparator output should not be used in conjunction with synchronized input clock.

 2016-2018 Microchip Technology Inc. DS40001866B-page 322


PIC16(L)F15356/75/76/85/86
26.1 Timer1 Operation 26.2 Clock Source Selection
The Timer1 modules are 16-bit incrementing counters The T1CLK register is used to select the clock source for
which are accessed through the TMR1H:TMR1L the timer. Register 26-3 shows the possible clock
register pairs. Writes to TMR1H or TMR1L directly sources that may be selected to make the timer
update the counter. increment.
When used with an internal clock source, the module is
26.2.1 INTERNAL CLOCK SOURCE
a timer and increments on every instruction cycle.
When used with an external clock source, the module When the internal clock source FOSC is selected, the
can be used as either a timer or counter and incre- TMR1H:TMR1L register pair will increment on multiples
ments on every selected edge of the external source. of FOSC as determined by the respective Timer1
prescaler.
The timer is enabled by configuring the TMR1ON and
GE bits in the T1CON and T1GCON registers, When the FOSC internal clock source is selected, the
respectively. Table 26-1 displays the Timer1 enable timer register value will increment by four counts every
selections. instruction clock cycle. Due to this condition, a 2 LSB
error in resolution will occur when reading the
TMR1H:TMR1L value. To utilize the full resolution of the
TABLE 26-1: TIMER1 ENABLE timer in this mode, an asynchronous input signal must
SELECTIONS be used to gate the timer clock input.
Timer1 Out of the total timer gate signal sources, the following
TMR1ON TMR1GE
Operation subset of sources can be asynchronous and may be
1 1 Count Enabled useful for this purpose:
1 0 Always On • CLC4 output
0 1 Off • CLC3 output
• CLC2 output
0 0 Off
• CLC1 output
• Zero-Cross Detect output
• Comparator2 output
• Comparator1 output
• TxG PPS remappable input pin

26.2.2 EXTERNAL CLOCK SOURCE


When the timer is enabled and the external clock input
source (ex: T1CKI PPS remappable input) is selected as
the clock source, the timer will increment on the rising
edge of the external clock input.
When using an external clock source, the timer can be
configured to run synchronously or asynchronously, as
described in Section 26.5 “Timer Operation in
Asynchronous Mode”.
When used as a timer with a clock oscillator, an
external 32.768 kHz crystal can be used connected to
the SOSCI/SOSCO pins.
Note: When using Timer1 to count events, a fall-
ing edge must be registered by the
counter prior to the first incrementing ris-
ing edge after any one or more of the fol-
lowing conditions:
•The timer is first enabled after POR
•Firmware writes to TMR1H or TMR1L
•The timer is disabled
•The timer is re-enabled (e.g.,
TMR1ON-->1) when the T1CKI
signal is currently logic low.

 2016-2018 Microchip Technology Inc. DS40001866B-page 323


PIC16(L)F15356/75/76/85/86
26.3 Timer Prescaler
Timer1 has four prescaler options allowing 1, 2, 4 or 8
divisions of the clock input. The CKPS bits of the
T1CON register control the prescale counter. The
prescale counter is not directly readable or writable;
however, the prescaler counter is cleared upon a write to
TMR1H or TMR1L.

 2016-2018 Microchip Technology Inc. DS40001866B-page 324


PIC16(L)F15356/75/76/85/86
26.4 Secondary Oscillator 26.5.1 READING AND WRITING TIMER1 IN
ASYNCHRONOUS MODE
A dedicated low-power 32.768 kHz oscillator circuit is
built-in between pins SOSCI (input) and SOSCO Reading TMR1H or TMR1L while the timer is running
(amplifier output). This internal circuit is designed to be from an external asynchronous clock will ensure a valid
used in conjunction with an external 32.768 kHz read (taken care of in hardware). However, the user
crystal. should keep in mind that reading the 16-bit timer in two
8-bit values itself, poses certain problems, since the
The oscillator circuit is enabled by setting the SOSCEN
timer may overflow between the reads.
bit of the OSCEN register. The oscillator will continue to
run during Sleep. For writes, it is recommended that the user simply stop
the timer and write the desired values. A write
Note: The oscillator requires a start-up and contention may occur by writing to the timer registers,
stabilization time before use. Thus, while the register is incrementing. This may produce an
SOSCEN should be set and a suitable unpredictable value in the TMR1H:TMR1L register pair.
delay observed prior to using Timer1 with
the SOSC source. A suitable delay similar
26.6 Timer Gate
to the OST delay can be implemented in
software by clearing the TMR1IF bit then Timer1 can be configured to count freely or the count
presetting the TMR1H:TMR1L register can be enabled and disabled using the time gate
pair to FC00h. The TMR1IF flag will be set circuitry. This is also referred to as Timer Gate Enable.
when 1024 clock cycles have elapsed,
The timer gate can also be driven by multiple select-
thereby indicating that the oscillator is
able sources.
running and reasonably stable.
26.6.1 TIMER GATE ENABLE
26.5 Timer Operation in Asynchronous The Timer Gate Enable mode is enabled by setting the
Mode GE bit of the T1GCON register. The polarity of the
Timer Gate Enable mode is configured using the GPOL
If the control bit SYNC of the T1CON register is set, the
bit of the T1GCON register.
external clock input is not synchronized. The timer
increments asynchronously to the internal phase When Timer Gate Enable signal is enabled, the timer
clocks. If the external clock source is selected then the will increment on the rising edge of the Timer1 clock
timer will continue to run during Sleep and can source. When Timer Gate Enable signal is disabled,
generate an interrupt on overflow, which will wake-up the timer always increments, regardless of the GE bit.
the processor. However, special precautions in See Figure 26-3 for timing details.
software are needed to read/write the timer (see
Section 26.5.1 “Reading and Writing Timer1 in
TABLE 26-2: TIMER GATE ENABLE
Asynchronous Mode”).
SELECTIONS
Note: When switching from synchronous to
T1CLK T1GPOL T1G Timer Operation
asynchronous operation, it is possible to
skip an increment. When switching from  1 1 Counts
asynchronous to synchronous operation,  1 0 Holds Count
it is possible to produce an additional
 0 1 Holds Count
increment.
 0 0 Counts

 2016-2018 Microchip Technology Inc. DS40001866B-page 325


PIC16(L)F15356/75/76/85/86
26.6.2 TIMER GATE SOURCE SELECTION 26.6.4 TIMER1 GATE SINGLE-PULSE
One of the several different external or internal signal MODE
sources may be chosen to gate the timer and allow the When Timer1 Gate Single-Pulse mode is enabled, it is
timer to increment. The gate input signal source can be possible to capture a single-pulse gate event. Timer1
selected based on the T1GATE register setting. See the Gate Single-Pulse mode is first enabled by setting the
T1GATE register (Register 26-4) description for a GSPM bit in the T1GCON register. Next, the GGO/
complete list of the available gate sources. The polarity DONE bit in the T1GCON register must be set. The
for each available source is also selectable. Polarity timer will be fully enabled on the next incrementing
selection is controlled by the GPOL bit of the T1GCON edge. On the next trailing edge of the pulse, the GGO/
register. DONE bit will automatically be cleared. No other gate
events will be allowed to increment the timer until the
26.6.2.1 T1G Pin Gate Operation GGO/DONE bit is once again set in software. See
The T1G pin is one source for the timer gate control. It Figure 26-5 for timing details.
can be used to supply an external source to the time If the Single-Pulse Gate mode is disabled by clearing the
gate circuitry. GSPM bit in the T1GCON register, the GGO/DONE bit
should also be cleared.
26.6.2.2 Timer0 Overflow Gate Operation
Enabling the Toggle mode and the Single-Pulse mode
When Timer0 overflows, or a period register match simultaneously will permit both sections to work
condition occurs (in 8-bit mode), a low-to-high pulse will together. This allows the cycle times on the timer gate
automatically be generated and internally supplied to source to be measured. See Figure 26-6 for timing
the Timer1 gate circuitry. details.
26.6.2.3 Comparator C1 Gate Operation 26.6.5 TIMER1 GATE VALUE STATUS
The output resulting from a Comparator 1 operation can When Timer1 Gate Value Status is utilized, it is possible
be selected as a source for the timer gate control. The to read the most current level of the gate control value.
Comparator 1 output can be synchronized to the timer The value is stored in the GVAL bit in the T1GCON reg-
clock or left asynchronous. For more information see ister. The GVAL bit is valid even when the timer gate is
Section 23.4.1 “Comparator Output not enabled (GE bit is cleared).
Synchronization”.
26.6.6 TIMER1 GATE EVENT INTERRUPT
26.6.2.4 Comparator C2 Gate Operation
When Timer1 Gate Event Interrupt is enabled, it is
The output resulting from a Comparator 2 operation possible to generate an interrupt upon the completion
can be selected as a source for the timer gate control. of a gate event. When the falling edge of GVAL occurs,
The Comparator 2 output can be synchronized to the the TMR1GIF flag bit in the PIR5 register will be set. If
timer clock or left asynchronous. For more information the TMR1GIE bit in the PIE5 register is set, then an
see Section 23.4.1 “Comparator Output interrupt will be recognized.
Synchronization”.
The TMR1GIF flag bit operates even when the timer
26.6.3 TIMER1 GATE TOGGLE MODE gate is not enabled (TMR1GE bit is cleared).
When Timer1 Gate Toggle mode is enabled, it is possi-
ble to measure the full-cycle length of a timer gate sig-
nal, as opposed to the duration of a single level pulse.
The timer gate source is routed through a flip-flop that
changes state on every incrementing edge of the
signal. See Figure 26-4 for timing details.
Timer1 Gate Toggle mode is enabled by setting the
GTM bit of the T1GCON register. When the GTM bit is
cleared, the flip-flop is cleared and held clear. This is
necessary in order to control which edge is measured.
Note: Enabling Toggle mode at the same time
as changing the gate polarity may result in
indeterminate operation.

 2016-2018 Microchip Technology Inc. DS40001866B-page 326


PIC16(L)F15356/75/76/85/86
26.7 Timer1 Interrupts 26.9 CCP Capture/Compare Time Base
The timer register pair (TMR1H:TMR1L) increments to The CCP modules use the TMR1H:TMR1L register
FFFFh and rolls over to 0000h. When the timer rolls pair as the time base when operating in Capture or
over, the respective timer interrupt flag bit of the PIR5 Compare mode.
register is set. To enable the interrupt on rollover, you In Capture mode, the value in the TMR1H:TMR1L
must set these bits: register pair is copied into the CCPRxH:CCPRxL
• ON bit of the T1CON register register pair on a configured event.
• TMR1IE bit of the PIE4 register In Compare mode, an event is triggered when the value
• PEIE bit of the INTCON register CCPRxH:CCPRxL register pair matches the value in
• GIE bit of the INTCON register the TMR1H:TMR1L register pair. This event can be an
Auto-conversion Trigger.
The interrupt is cleared by clearing the TMR1IF bit in
the Interrupt Service Routine. For more information, see Section 28.0 “Capture/
Compare/PWM Modules”.

Note: To avoid immediate interrupt vectoring, 26.10 CCP Auto-Conversion Trigger


the TMR1H:TMR1L register pair should When any of the CCP’s are configured to trigger an
be preloaded with a value that is not immi- auto-conversion, the trigger will clear the
nently about to rollover, and the TMR1IF TMR1H:TMR1L register pair. This auto-conversion
flag should be cleared prior to enabling does not cause a timer interrupt. The CCP module may
the timer interrupts. still be configured to generate a CCP interrupt.
In this mode of operation, the CCPRxH:CCPRxL
26.8 Timer1 Operation During Sleep register pair becomes the period register for Timer1.
Timer1 can only operate during Sleep when setup in The timer should be synchronized and FOSC/4 should
Asynchronous Counter mode. In this mode, an external be selected as the clock source in order to utilize the
crystal or clock source can be used to increment the Auto-conversion Trigger. Asynchronous operation of
counter. To set up the timer to wake the device: the timer can cause an Auto-conversion Trigger to be
• ON bit of the T1CON register must be set missed.
• TMR1IE bit of the PIE4 register must be set In the event that a write to TMR1H or TMR1L coincides
• PEIE bit of the INTCON register must be set with an Auto-conversion Trigger from the CCP, the
write will take precedence.
• SYNC bit of the T1CON register must be set
• CS bits of the T1CLK register must be configured For more information, see Section 28.2.4 “Compare
During Sleep”.
• The timer clock source must be enabled and
continue operation during sleep. When the SOSC
is used for this purpose, the SOSCEN bit of the
OSCEN register must be set.
The device will wake-up on an overflow and execute
the next instructions. If the GIE bit of the INTCON
register is set, the device will call the Interrupt Service
Routine.
Secondary oscillator will continue to operate in Sleep
regardless of the SYNC bit setting.

 2016-2018 Microchip Technology Inc. DS40001866B-page 327


PIC16(L)F15356/75/76/85/86
FIGURE 26-2: TIMER1 INCREMENTING EDGE

TxCKI = 1
when the timer is
enabled

TxCKI = 0
when the timer is
enabled

Note 1: Arrows indicate counter increments.


2: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock.

FIGURE 26-3: TIMER1 GATE ENABLE MODE

TMRxGE

TxGPOL

Selected
gate input

TxCKI

TxGVAL

TMRxH:TMRxL N N+1 N+2 N+3 N+4


Count

 2016-2018 Microchip Technology Inc. DS40001866B-page 328


PIC16(L)F15356/75/76/85/86
FIGURE 26-4: TIMER1 GATE TOGGLE MODE

TMRxGE

TxGPOL

TxGTM

Selected
gate input
TxCKI

TxGVAL

TMRxH:TMRxL N N+1 N+2 N+3 N+4 N+5 N+6 N+7 N+8


Count

FIGURE 26-5: TIMER1 GATE SINGLE-PULSE MODE

TMRxGE

TxGPOL

TxGSPM
Cleared by hardware on
TxGGO/ Set by software falling edge of TxGVAL
DONE
Counting enabled on
rising edge of selected source
Selected gate
source

TxCKI

TxGVAL

TMRxH:TMRxL N N+1 N+2


Count
Cleared by
TMRxGIF Cleared by software Set by hardware on software
falling edge of TxGVAL

 2016-2018 Microchip Technology Inc. DS40001866B-page 329


PIC16(L)F15356/75/76/85/86
FIGURE 26-6: TIMER1 GATE SINGLE-PULSE AND TOGGLE COMBINED MODE

TMRxGE

TxGPOL

TxGSPM

TxGTM

Cleared by hardware on
TxGGO/ Set by software falling edge of TxGVAL
DONE Counting enabled on
rising edge of selected source
Selected gate
source

TxCKI

TxGVAL

TMRxH:TMRxL N N+1 N+2 N+3 N+4


Count
Set by hardware on Cleared by
TMRxGIF Cleared by software falling edge of TxGVAL software

 2016-2018 Microchip Technology Inc. DS40001866B-page 330


PIC16(L)F15356/75/76/85/86
26.11 Register Definitions: Timer1 Control

REGISTER 26-1: T1CON: TIMER1 CONTROL REGISTER


U-0 U-0 R/W-0/u R/W-0/u U-0 R/W-0/u R/W-0/u R/W-0/u
— — CKPS<1:0> — SYNC RD16 ON
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-4 CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 =1:8 Prescale value
10 =1:4 Prescale value
01 =1:2 Prescale value
00 =1:1 Prescale value
bit 3 Unimplemented: Read as ‘0’
bit 2 SYNC: Timer1 Synchronization Control bit
When TMR1CLK = FOSC or FOSC/4
This bit is ignored. The timer uses the internal clock and no additional synchronization is performed.
ELSE
0 = Synchronize external clock input with system clock
1 = Do not synchronize external clock input
bit 1 RD16: 16-bit Read/Write Mode Enable bit
0 = Enables register read/write of Timer1 in two 8-bit operation
1 = Enables register read/write of Timer1 in one 16-bit operation
bit 0 ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1 and clears Timer1 gate flip-flop

 2016-2018 Microchip Technology Inc. DS40001866B-page 331


PIC16(L)F15356/75/76/85/86

REGISTER 26-2: T1GCON: TIMER1 GATE CONTROL REGISTER


R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W/HC-0/u R-x/x U-0 U-0
GE GPOL GTM GSPM GGO/DONE GVAL — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware

bit 7 GE: Timer1 Gate Enable bit


If ON = 0:
This bit is ignored
If ON = 1:
1 = Timer1 counting is controlled by the Timer1 gate function
0 = Timer1 is always counting
bit 6 GPOL: Timer1 Gate Polarity bit
1 = Timer1 gate is active-high (Timer1 counts when gate is high)
0 = Timer1 gate is active-low (Timer1 counts when gate is low)
bit 5 GTM: Timer1 Gate Toggle Mode bit
1 = Timer1 Gate Toggle mode is enabled
0 = Timer1 Gate Toggle mode is disabled and toggle flip-flop is cleared
Timer1 gate flip-flop toggles on every rising edge.
bit 4 GSPM: Timer1 Gate Single-Pulse Mode bit
1 = Timer1 Gate Single-Pulse mode is enabled
0 = Timer1 Gate Single-Pulse mode is disabled
bit 3 GGO/DONE: Timer1 Gate Single-Pulse Acquisition Status bit
1 = Timer1 gate single-pulse acquisition is ready, waiting for an edge
0 = Timer1 gate single-pulse acquisition has completed or has not been started
This bit is automatically cleared when GSPM is cleared
bit 2 GVAL: Timer1 Gate Value Status bit
Indicates the current state of the Timer1 gate that could be provided to TMR1H:TMR1L
Unaffected by Timer1 Gate Enable (GE)
bit 1-0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 332


PIC16(L)F15356/75/76/85/86

REGISTER 26-3: T1CLK TIMER1 CLOCK SELECT REGISTER


U-0 U-0 U-0 U-0 R/W-0/u R/W-0/u R/W-0/u R/W-0/u
— — — — CS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 CS<3:0>: Timer1 Clock Select bits
1111 = Reserved
1110 = Reserved
1101 = LC4_out
1100 = LC3_out
1011 = LC2_out
1010 = LC1_out
1001 = Timer0 overflow output
1000 = CLKR output
0111 = SOSC
0110 = MFINTOSC (32 kHz)
0101 = MFINTOSC (500 kHz)
0100 = LFINTOSC
0011 = HFINTOSC
0010 = FOSC
0001 = FOSC/4
0000 = T1CKIPPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 333


PIC16(L)F15356/75/76/85/86

REGISTER 26-4: T1GATE TIMER1 GATE SELECT REGISTER


U-0 U-0 U-0 R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W-0/u
— — — GSS<4:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware

bit 7-5 Unimplemented: Read as ‘0’


bit 4-0 GSS<4:0>: Timer1 Gate Select bits
11111-10001 = Reserved
10000 = LC4_out
01111 = LC3_out
01110 = LC2_out
01101 = LC1_out
00100 = ZCD1_output
01011 = C2OUT_sync
01010 = C1OUT_sync
01001 = NCO1_out
01000 = PWM6_out
00111 = PWM5_out
00110 = PWM4_out
00101 = PWM3_out
00100 = CCP2_out
00011 = CCP1_out
00010 = TMR2_postscaled
00001 = Timer0 overflow output
00000 = T1GPPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 334


PIC16(L)F15356/75/76/85/86

TABLE 26-3: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER1


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE ― ― ― ― ― INTEDG 147


PIE4 — — — — — — TMR2IE TMR1IE 152
PIR4 — — — — — — TMR2IF TMR1IF 160
T1CON — — CKPS<1:0> — SYNC RD16 ON 331
T1GCON GE GPOL GTM GSPM GGO/DONE GVAL — — 332
T1GATE — — — GSS<4:0> 334
T1CLK — — — — CS<3:0> 333
TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register 322*
TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register 322*
T1CKIPPS ― ― T1CKIPPS<5:0> 242
T1GPPS ― ― T1GPPS<5:0> 242
CCPxCON CCPxEN CCPxOE CCPxOUT CCPxFMT CCPxMODE<3:0> 364
CLCxSELy ― ― ― LCxDyS<4:0> 409
ADACT ― ― ― ADACT<4:0> 281
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used with the Timer1 modules.
* Page with register information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 335


PIC16(L)F15356/75/76/85/86
27.0 TIMER2 MODULE WITH • Selectable external hardware timer Resets
HARDWARE LIMIT TIMER (HLT) • Programmable prescaler (1:1 to 1:128)
• Programmable postscaler (1:1 to 1:16)
The Timer2 module is an 8-bit timer that can operate as
• Selectable synchronous/asynchronous operation
free-running period counters or in conjunction with
external signals that control start, run, freeze, and reset • Alternate clock sources
operation in One-Shot and Monostable modes of • Interrupt-on-period
operation. Sophisticated waveform control such as • Three modes of operation:
pulse density modulation are possible by combining the - Free Running Period
operation of this timer with other internal peripherals - One-shot
such as the comparators and CCP modules. Features
- Monostable
of the timer include:
See Figure 27-1 for a block diagram of Timer2. See
• 8-bit timer register
Figure 27-2 for the clock source block diagram.
• 8-bit period register

FIGURE 27-1: TIMER2 BLOCK DIAGRAM


RSEL <:0> Rev. 10-000168C
9/10/2015

INPPS
TxIN PPS MODE<4:0> MODE<3>

Edge Detector reset


External
TMRx_ers Level Detector CCP_pset(1)
Reset
(2) Mode Control
Sources (2 clock Sync)

enable MODE<4:3>=01
Clear ON
MODE<4:1>=1011 D Q

CPOL
TMRx_clk Prescaler 0
R
T[7MR
Set flag bit
3 Sync 1 TMRxIF

CKPS<2:0> Fosc/4 PSYNC TMRx_postscaled


Comparator Postscaler

4
ON Sync
(2 Clocks)
1
7[PR OUTPS<3:0>
0

CSYNC

Note 1: Signal to the CCP to trigger the PWM pulse.


2: See Register 27-4 for external Reset sources.

 2016-2018 Microchip Technology Inc. DS40001866B-page 336


PIC16(L)F15356/75/76/85/86
FIGURE 27-2: TIMER2 CLOCK SOURCE the output postscaler counter. When the postscaler
BLOCK DIAGRAM count equals the value in the OUTPS<4:0> bits of the
TMR2CON1 register, a one TMR2_clk period wide pulse
TxCLKCON Rev. 10-000 169B
occurs on the TMR2_postscaled output, and the
5/29/201 4
postscaler count is cleared.
TXINPPS
TXIN PPS 27.1.2 ONE-SHOT MODE
The One-Shot mode is identical to the Free Running
Period mode except that the ON bit is cleared and the
timer is stopped when TMR2 matches PR2 and will not
Timer Clock Sources TMR2_clk restart until the T2ON bit is cycled off and on.
(See Table 27-2) Postscaler OUTPS<4:0> values other than 0 are
meaningless in this mode because the timer is stopped
at the first period event and the postscaler is reset
when the timer is restarted.

27.1.3 MONOSTABLE MODE


Monostable modes are similar to One-Shot modes
except that the ON bit is not cleared and the timer can
be restarted by an external Reset event.
27.1 Timer2 Operation
Timer2 operates in three major modes: 27.2 Timer2 Output
• Free Running Period The Timer2 module’s primary output is TMR2_posts-
• One-shot caled, which pulses for a single TMR2_clk period when
• Monostable the postscaler counter matches the value in the
Within each mode there are several options for starting, OUTPS bits of the TMR2CON register. The PR2 post-
stopping, and reset. Table 27-1 lists the options. scaler is incremented each time the TMR2 value
matches the PR2 value. This signal can be selected as
In all modes, the TMR2 count register is incremented an input to several other input modules:
on the rising edge of the clock signal from the program-
mable prescaler. When TMR2 equals PR2, a high level • The ADC module, as an Auto-conversion Trigger
is output to the postscaler counter. TMR2 is cleared on • COG, as an auto-shutdown source
the next clock input. In addition, the Timer2 is also used by the CCP module
An external signal from hardware can also be config- for pulse generation in PWM mode. Both the actual
ured to gate the timer operation or force a TMR2 count TMR2 value as well as other internal signals are sent to
Reset. In Gate modes the counter stops when the gate the CCP module to properly clock both the period and
is disabled and resumes when the gate is enabled. In pulse width of the PWM signal. See Section 28.0
Reset modes the TMR2 count is reset on either the “Capture/Compare/PWM Modules” for more details
level or edge from the external source. on setting up Timer2 for use with the CCP, as well as
the timing diagrams in Section 27.5 “Operation
The TMR2 and PR2 registers are both directly readable
Examples” for examples of how the varying Timer2
and writable. The TMR2 register is cleared and the
modes affect CCP PWM output.
PR2 register initializes to FFh on any device Reset.
Both the prescaler and postscaler counters are cleared
on the following events: 27.3 External Reset Sources
• a write to the TMR2 register In addition to the clock source, the Timer2 also takes in
• a write to the T2CON register an external Reset source. This external Reset source
is selected for Timer2 with the T2RST register. This
• any device Reset
source can control starting and stopping of the timer, as
• External Reset Source event that resets the timer. well as resetting the timer, depending on which mode
Note: TMR2 is not cleared when T2CON is the timer is in. The mode of the timer is controlled by
written. the MODE<4:0> bits of the TMR2HLT register. Edge-
Triggered modes require six Timer clock periods
27.1.1 FREE RUNNING PERIOD MODE between external triggers. Level-Triggered modes
require the triggering level to be at least three Timer
The value of TMR2 is compared to that of the Period
clock periods long. External triggers are ignored while
register, PR2, on each TMR2_clk cycle. When the two
in Debug Freeze mode.
values match, the comparator resets the value of TMR2
to 00h on the next rising TMR2_clk edge and increments

 2016-2018 Microchip Technology Inc. DS40001866B-page 337


PIC16(L)F15356/75/76/85/86

TABLE 27-1: TIMER2 OPERATING MODES


MODE<4:0> Output Timer Control
Mode Operation
<4:3> <2:0> Operation Start Reset Stop
000 Software gate (Figure 27-4) ON = 1 — ON = 0
Hardware gate, active-high ON = 1 and — ON = 0 or
001 Period
(Figure 27-5) TMRx_ers = 1 TMRx_ers = 0
Pulse
ON = 1 and — ON = 0 or
010 Hardware gate, active-low
TMRx_ers = 0 TMRx_ers = 1
Free 011 Rising or falling edge Reset TMRx_ers ↕
Running 00
Period 100 Period Rising edge Reset (Figure 27-6) TMRx_ers ↑ ON = 0
101 Pulse Falling edge Reset TMRx_ers ↓
with ON = 1 ON = 0 or
110 Hardware Low level Reset TMRx_ers = 0
TMRx_ers = 0
Reset
High level Reset (Figure 27-7) ON = 0 or
111 TMRx_ers = 1
TMRx_ers = 1
000 One-shot Software start (Figure 27-8) ON = 1 —
ON = 1 and
001 Rising edge start (Figure 27-9) —
Edge TMRx_ers ↑
triggered ON = 1 and
010 Falling edge start —
start TMRx_ers ↓
(Note 1) ON = 1 and ON = 0
011 Any edge start — or
TMRx_ers ↕
Next clock
One-shot 01 Rising edge start and ON = 1 and
100 TMRx_ers ↑ after
Edge Rising edge Reset (Figure 27-10) TMRx_ers ↑ TMRx = PRx
triggered Falling edge start and ON = 1 and (Note 2)
101 start TMRx_ers ↓
Falling edge Reset TMRx_ers ↓
and
hardware Rising edge start and ON = 1 and
110 TMRx_ers = 0
Reset Low level Reset (Figure 27-11) TMRx_ers ↑
(Note 1) Falling edge start and ON = 1 and
111 TMRx_ers = 1
High level Reset TMRx_ers ↓
000 Reserved
Rising edge start ON = 1 and ON = 0
001 —
Edge (Figure 27-12) TMRx_ers ↑ or
Mono-stable triggered ON = 1 and Next clock
010 Falling edge start —
start TMRx_ers ↓ after
(Note 1) ON = 1 and TMRx = PRx
011 Any edge start — (Note 3)
TMRx_ers ↕
Reserved 10 100 Reserved
Reserved 101 Reserved
Level High level start and ON = 1 and
110 TMRx_ers = 0
triggered Low level Reset (Figure 27-13) TMRx_ers = 1
ON = 0 or
start
One-shot Held in Reset
and Low level start & ON = 1 and
111 TMRx_ers = 1 (Note 2)
hardware High level Reset TMRx_ers = 0
Reset
Reserved 11 xxx Reserved
Note 1: If ON = 0 then an edge is required to restart the timer after ON = 1.
2: When TMRx = PRx then the next clock clears ON and stops TMRx at 00h.
3: When TMRx = PRx then the next clock stops TMRx at 00h but does not clear ON.

 2016-2018 Microchip Technology Inc. DS40001866B-page 338


PIC16(L)F15356/75/76/85/86
27.4 Timer2 Interrupt
Timer2 can also generate a device interrupt. The
interrupt is generated when the postscaler counter
matches one of 16 postscale options (from 1:1 through
1:16), which are selected with the postscaler control
bits, OUTPS<3:0> of the T2CON register. The interrupt
is enabled by setting the TMR2IE interrupt enable bit of
the PIE4 register. Interrupt timing is illustrated in
Figure 27-3.

FIGURE 27-3: TIMER2 PRESCALER, POSTSCALER, AND INTERRUPT TIMING DIAGRAM


Rev. 10-000205A
4/7/2016

CKPS 0b010

PRx 1

OUTPS 0b0001

TMRx_clk

TMRx 0 1 0 1 0 1 0

TMRx_postscaled

(1) (2) (1)


TMRxIF

Note 1: Setting the interrupt flag is synchronized with the instruction clock.
Synchronization may take as many as 2 instruction cycles
2: Cleared by software.

 2016-2018 Microchip Technology Inc. DS40001866B-page 339


PIC16(L)F15356/75/76/85/86
27.5 Operation Examples 27.5.1 SOFTWARE GATE MODE
Unless otherwise specified, the following notes apply to This mode corresponds to legacy Timer2 operation.
the following timing diagrams: The timer increments with each clock input when
ON = 1 and does not increment when ON = 0. When
- Both the prescaler and postscaler are set to the TMR2 count equals the PR2 period count the timer
1:1 (both the CKPS and OUTPS bits in the resets on the next clock and continues counting from 0.
T2CON register are cleared). Operation with the ON bit software controlled is illus-
- The diagrams illustrate any clock except trated in Figure 27-4. With PR2 = 5, the counter
Fosc/4 and show clock-sync delays of at advances until TMR2 = 5, and goes to zero with the
least two full cycles for both ON and next clock.
Timer2_ers. When using Fosc/4, the clock-
sync delay is at least one instruction period
for Timer2_ers; ON applies in the next
instruction period.
- The PWM Duty Cycle and PWM output are
illustrated assuming that the timer is used for
the PWM function of the CCP module as
described in Section 28.0 “Capture/Com-
pare/PWM Modules”. The signals are not a
part of the Timer2 module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 340


PIC16(L)F15356/75/76/85/86
FIGURE 27-4: SOFTWARE GATE MODE TIMING DIAGRAM (MODE = 00000)
Rev. 10-000195B
5/30/2014

MODE 0b00000

TMRx_clk

Instruction(1) BSF BCF BSF

ON

PRx 5

TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.

 2016-2018 Microchip Technology Inc. DS40001866B-page 341


PIC16(L)F15356/75/76/85/86
27.5.2 HARDWARE GATE MODE When MODE<4:0> = 00001 then the timer is stopped
when the external signal is high. When
The Hardware Gate modes operate the same as the
MODE<4:0> = 00010 then the timer is stopped when
Software Gate mode except the TMR2_ers external
the external signal is low.
signal gates the timer. When used with the CCP the
gating extends the PWM period. If the timer is stopped Figure 27-5 illustrates the Hardware Gating mode for
when the PWM output is high then the duty cycle is also MODE<4:0> = 00001 in which a high input level starts
extended. the counter.

FIGURE 27-5: HARDWARE GATE MODE TIMING DIAGRAM (MODE = 00001)


Rev. 10-000 196B
5/30/201 4

MODE 0b00001

TMRx_clk

TMRx_ers

PRx 5

TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 1

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

 2016-2018 Microchip Technology Inc. DS40001866B-page 342


PIC16(L)F15356/75/76/85/86
27.5.3 EDGE-TRIGGERED HARDWARE When the timer is used in conjunction with the CCP in
LIMIT MODE PWM mode then an early Reset shortens the period
and restarts the PWM pulse after a two clock delay.
In Hardware Limit mode the timer can be reset by the
Refer to Figure 27-6.
TMR2_ers external signal before the timer reaches the
period count. Three types of Resets are possible:
• Reset on rising or falling edge
(MODE<4:0>= 00011)
• Reset on rising edge (MODE<4:0> = 00100)
• Reset on falling edge (MODE<4:0> = 00101)

FIGURE 27-6: EDGE-TRIGGERED HARDWARE LIMIT MODE TIMING DIAGRAM


(MODE = 00100)
Rev. 10-000 197B
5/30/201 4

MODE 0b00100

TMRx_clk

PRx 5

Instruction(1) BSF BCF BSF

ON

TMRx_ers

TMRx 0 1 2 0 1 2 3 4 5 0 1 2 3 4 5 0 1

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.

 2016-2018 Microchip Technology Inc. DS40001866B-page 343


PIC16(L)F15356/75/76/85/86
27.5.4 LEVEL-TRIGGERED HARDWARE When the CCP uses the timer as the PWM time base
LIMIT MODE then the PWM output will be set high when the timer
starts counting and then set low only when the timer
In the Level-Triggered Hardware Limit Timer modes the
count matches the CCPRx value. The timer is reset
counter is reset by high or low levels of the external
when either the timer count matches the PR2 value or
signal TMR2_ers, as shown in Figure 27-7. Selecting
two clock periods after the external Reset signal goes
MODE<4:0> = 00110 will cause the timer to reset on a
true and stays true.
low level external signal. Selecting
MODE<4:0> = 00111 will cause the timer to reset on a The timer starts counting, and the PWM output is set
high level external signal. In the example, the counter high, on either the clock following the PR2 match or two
is reset while TMR2_ers = 1. ON is controlled by BSF clocks after the external Reset signal relinquishes the
and BCF instructions. When ON = 0 the external signal Reset. The PWM output will remain high until the timer
is ignored. counts up to match the CCPRx pulse width value. If the
external Reset signal goes true while the PWM output
is high then the PWM output will remain high until the
Reset signal is released allowing the timer to count up
to match the CCPRx value.

FIGURE 27-7: LEVEL-TRIGGERED HARDWARE LIMIT MODE TIMING DIAGRAM


(MODE = 00111)
Rev. 10-000198B
5/30/2014

MODE 0b00111

TMRx_clk

PRx 5

Instruction(1) BSF BCF BSF

ON

TMRx_ers

TMRx 0 1 2 0 1 2 3 4 5 0 0 1 2 3 4 5 0

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.

 2016-2018 Microchip Technology Inc. DS40001866B-page 344


PIC16(L)F15356/75/76/85/86
27.5.5 SOFTWARE START ONE-SHOT When One-Shot mode is used in conjunction with the
MODE CCP PWM operation the PWM pulse drive starts
concurrent with setting the ON bit. Clearing the ON bit
In One-Shot mode the timer resets and the ON bit is
while the PWM drive is active will extend the PWM
cleared when the timer value matches the PR2 period
drive. The PWM drive will terminate when the timer
value. The ON bit must be set by software to start
value matches the CCPRx pulse width value. The
another timer cycle. Setting MODE<4:0> = 01000
PWM drive will remain off until software sets the ON bit
selects One-Shot mode which is illustrated in
to start another cycle. If software clears the ON bit after
Figure 27-8. In the example, ON is controlled by BSF
the CCPRx match but before the PR2 match then the
and BCF instructions. In the first case, a BSF instruc-
PWM drive will be extended by the length of time the
tion sets ON and the counter runs to completion and
ON bit remains cleared. Another timing cycle can only
clears ON. In the second case, a BSF instruction starts
be initiated by setting the ON bit after it has been
the cycle, BCF/BSF instructions turn the counter off
cleared by a PR2 period count match.
and on during the cycle, and then it runs to completion.

FIGURE 27-8: SOFTWARE START ONE-SHOT MODE TIMING DIAGRAM (MODE = 01000)
Rev. 10-000199B
4/7/2016

MODE 0b01000

TMRx_clk

PRx 5

Instruction(1) BSF BSF BCF BSF

ON

TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions
executed by the CPU to set or clear the ON bit of TxCON. CPU
execution is asynchronous to the timer clock input.

 2016-2018 Microchip Technology Inc. DS40001866B-page 345


PIC16(L)F15356/75/76/85/86
27.5.6 EDGE-TRIGGERED ONE-SHOT If the timer is halted by clearing the ON bit then another
MODE TMR2_ers edge is required after the ON bit is set to
resume counting. Figure 27-9 illustrates operation in
The Edge-Triggered One-Shot modes start the timer the rising edge One-Shot mode.
on an edge from the external signal input, after the ON
When Edge-Triggered One-Shot mode is used in con-
bit is set, and clear the ON bit when the timer matches
junction with the CCP then the edge-trigger will activate
the PR2 period value. The following edges will start the PWM drive and the PWM drive will deactivate when
the timer: the timer matches the CCPRx pulse width value and
• Rising edge (MODE<4:0> = 01001) stay deactivated when the timer halts at the PR2 period
• Falling edge (MODE<4:0> = 01010) count match.
• Rising or Falling edge (MODE<4:0> = 01011)

FIGURE 27-9: EDGE-TRIGGERED ONE-SHOT MODE TIMING DIAGRAM (MODE = 01001)


Rev. 10-000200B
5/19/2016

MODE 0b01001

TMRx_clk

PRx 5

Instruction(1) BSF BSF BCF

ON

TMRx_ers

TMRx 0 1 2 3 4 5 0 1 2

CCP_pset

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.

 2016-2018 Microchip Technology Inc. DS40001866B-page 346


27.5.7 EDGE-TRIGGERED HARDWARE LIMIT ONE-SHOT The timer resets and clears the ON bit when the timer value matches the PR2
 2016-2018 Microchip Technology Inc.

MODE period value. External signal edges will have no effect until after software sets
the ON bit. Figure 27-10 illustrates the rising edge hardware limit one-shot
In Edge-Triggered Hardware Limit One-Shot modes the timer starts on the first operation.
external signal edge after the ON bit is set and resets on all subsequent edges.
When this mode is used in conjunction with the CCP then the first starting edge
Only the first edge after the ON bit is set is needed to start the timer. The
trigger, and all subsequent Reset edges, will activate the PWM drive. The PWM
counter will resume counting automatically two clocks after all subsequent drive will deactivate when the timer matches the CCPRx pulse-width value and
external Reset edges. Edge triggers are as follows: stay deactivated until the timer halts at the PR2 period match unless an external
• Rising edge start and Reset (MODE<4:0> = 01100) signal edge resets the timer before the match occurs.
• Falling edge start and Reset (MODE<4:0> = 01101)

FIGURE 27-10: EDGE-TRIGGERED HARDWARE LIMIT ONE-SHOT MODE TIMING DIAGRAM (MODE = 01100)

Rev. 10-000201B
4/7/2016

MODE 0b01100

PIC16(L)F15356/75/76/85/86
TMRx_clk

PRx 5

Instruction(1) BSF BSF

ON

TMRx_ers

TMRx 0 1 2 3 4 5 0 1 2 0 1 2 3 4 5 0

TMRx_postscaled

PWM Duty
3
Cycle
DS40001866B-page 347

PWM Output

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.
27.5.8 LEVEL RESET, EDGE-TRIGGERED HARDWARE LIMIT When the timer count matches the PR2 period count, the timer is reset and the
 2016-2018 Microchip Technology Inc.

ONE-SHOT MODES ON bit is cleared. When the ON bit is cleared by either a PR2 match or by soft-
ware control a new external signal edge is required after the ON bit is set to start
In Level -Triggered One-Shot mode the timer count is reset on the external the counter.
signal level and starts counting on the rising/falling edge of the transition from
When Level-Triggered Reset One-Shot mode is used in conjunction with the
Reset level to the active level while the ON bit is set. Reset levels are selected
CCP PWM operation the PWM drive goes active with the external signal edge
as follows: that starts the timer. The PWM drive goes inactive when the timer count equals
• Low Reset level (MODE<4:0> = 01110) the CCPRx pulse width count. The PWM drive does not go active when the
• High Reset level (MODE<4:0> = 01111) timer count clears at the PR2 period count match.

FIGURE 27-11: LOW LEVEL RESET, EDGE-TRIGGERED HARDWARE LIMIT ONE-SHOT MODE TIMING DIAGRAM (MODE = 01110)
Rev. 10-000202B
4/7/2016

MODE 0b01110

TMRx_clk

PIC16(L)F15356/75/76/85/86
PRx 5

Instruction(1) BSF BSF

ON

TMRx_ers

TMRx 0 1 2 3 4 5 0 1 0 1 2 3 4 5 0

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output
DS40001866B-page 348

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.
27.5.9 EDGE-TRIGGERED MONOSTABLE MODES When an Edge-Triggered Monostable mode is used in conjunction with the
 2016-2018 Microchip Technology Inc.

CCP PWM operation the PWM drive goes active with the external Reset signal
The Edge-Triggered Monostable modes start the timer on an edge from the
edge that starts the timer, but will not go active when the timer matches the PR2
external Reset signal input, after the ON bit is set, and stop incrementing the
value. While the timer is incrementing, additional edges on the external Reset
timer when the timer matches the PR2 period value. The following edges will
signal will not affect the CCP PWM.
start the timer:
• Rising edge (MODE<4:0> = 10001)
• Falling edge (MODE<4:0> = 10010)
• Rising or Falling edge (MODE<4:0> = 10011)

FIGURE 27-12: RISING EDGE-TRIGGERED MONOSTABLE MODE TIMING DIAGRAM (MODE = 10001)
Rev. 10-000203A
4/7/2016

MODE 0b10001

TMRx_clk

PIC16(L)F15356/75/76/85/86
PRx 5

Instruction(1) BSF BCF BSF BCF BSF

ON

TMRx_ers

TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0

TMRx_postscaled

PWM Duty
3
Cycle

PWM Output
DS40001866B-page 349

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.
27.5.10 LEVEL-TRIGGERED HARDWARE LIMIT ONE-SHOT When the timer count matches the PR2 period count, the timer is reset and the
 2016-2018 Microchip Technology Inc.

MODES ON bit is cleared. When the ON bit is cleared by either a PR2 match or by soft-
ware control the timer will stay in Reset until both the ON bit is set and the exter-
The Level-Triggered Hardware Limit One-Shot modes hold the timer in Reset
nal signal is not at the Reset level.
on an external Reset level and start counting when both the ON bit is set and
the external signal is not at the Reset level. If one of either the external signal When Level-Triggered Hardware Limit One-Shot modes are used in conjunc-
is not in Reset or the ON bit is set then the other signal being set/made active tion with the CCP PWM operation the PWM drive goes active with either the
will start the timer. Reset levels are selected as follows: external signal edge or the setting of the ON bit, whichever of the two starts the
timer.
• Low Reset level (MODE<4:0> = 10110)
• High Reset level (MODE<4:0> = 10111)

FIGURE 27-13: LEVEL-TRIGGERED HARDWARE LIMIT ONE-SHOT MODE TIMING DIAGRAM (MODE = 10110)
Rev. 10-000204A
4/7/2016

MODE 0b10110

PIC16(L)F15356/75/76/85/86
TMR2_clk

PRx 5

Instruction(1) BSF BSF BCF BSF

ON

TMR2_ers

TMRx 0 1 2 3 4 5 0 1 2 3 0 1 2 3 4 5 0

TMR2_postscaled

PWM Duty
‘D3
Cycle

PWM Output
DS40001866B-page 350

Note 1: BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to
set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input.
PIC16(L)F15356/75/76/85/86
27.6 Timer2 Operation During Sleep
When PSYNC = 1, Timer2 cannot be operated while
the processor is in Sleep mode. The contents of the
TMR2 and PR2 registers will remain unchanged while
processor is in Sleep mode.
When PSYNC = 0, Timer2 will operate in Sleep as long
as the clock source selected is also still running.
Selecting the LFINTOSC, MFINTOSC, or HFINTOSC
oscillator as the timer clock source will keep the
selected oscillator running during Sleep.

 2016-2018 Microchip Technology Inc. DS40001866B-page 351


PIC16(L)F15356/75/76/85/86
27.7 Register Definitions: Timer2 Control

REGISTER 27-1: T2CLKCON: TIMER2 CLOCK SELECTION REGISTER


U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — CS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 CS<3:0>: Timer2 Clock Select bits
1111 = Reserved
1110 = LC4_out
1101 = LC3_out
1100 = LC2_out
1011 = LC1_out
1010 = ZCD1_output
1001 = NCO1_out
1000 = CLKR
0111 = SOSC
0110 = MFINTOSC (31.25 kHz)
0101 = MFINTOSC (500 kHz)
0100 = LFINTOSC
0011 = HFINTOSC (32 MHz)
0010 = FOSC
0001 = FOSC/4
0000 = T2CKIPPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 352


PIC16(L)F15356/75/76/85/86

REGISTER 27-2: T2CON: TIMER2 CONTROL REGISTER


R/W/HC-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ON(1) CKPS<2:0> OUTPS<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware

bit 7 ON: Timer2 On bit


1 = Timer2 is on
0 = Timer2 is off: all counters and state machines are reset
bit 6-4 CKPS<2:0>: Timer2-type Clock Prescale Select bits
111 =1:128 Prescaler
110 =1:64 Prescaler
101 =1:32 Prescaler
100 =1:16 Prescaler
011 =1:8 Prescaler
010 =1:4 Prescaler
001 =1:2 Prescaler
000 =1:1 Prescaler
bit 3-0 OUTPS<3:0>: Timer2 Output Postscaler Select bits
1111 =1:16 Postscaler
1110 =1:15 Postscaler
1101 =1:14 Postscaler
1100 =1:13 Postscaler
1011 =1:12 Postscaler
1010 =1:11 Postscaler
1001 =1:10 Postscaler
1000 =1:9 Postscaler
0111 =1:8 Postscaler
0110 =1:7 Postscaler
0101 =1:6 Postscaler
0100 =1:5 Postscaler
0011 =1:4 Postscaler
0010 =1:3 Postscaler
0001 =1:2 Postscaler
0000 =1:1 Postscaler

Note 1: In certain modes, the ON bit will be auto-cleared by hardware. See Section 27.5 “Operation Examples”.

 2016-2018 Microchip Technology Inc. DS40001866B-page 353


PIC16(L)F15356/75/76/85/86

REGISTER 27-3: T2HLT: TIMER2 HARDWARE LIMIT CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
PSYNC(1, 2) CKPOL(3) CKSYNC(4, 5) MODE<4:0>(6, 7)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 PSYNC: Timer2 Prescaler Synchronization Enable bit(1, 2)


1 = TMR2 Prescaler Output is synchronized to Fosc/4
0 = TMR2 Prescaler Output is not synchronized to Fosc/4
bit 6 CKPOL: Timer2 Clock Polarity Selection bit(3)
1 = Falling edge of input clock clocks timer/prescaler
0 = Rising edge of input clock clocks timer/prescaler
bit 5 CKSYNC: Timer2 Clock Synchronization Enable bit(4, 5)
1 = ON register bit is synchronized to TMR2_clk input
0 = ON register bit is not synchronized to TMR2_clk input
bit 4-0 MODE<4:0>: Timer2 Control Mode Selection bits(6, 7)
See Table 27-1.

Note 1: Setting this bit ensures that reading TM2x will return a valid value.
2: When this bit is ‘1’, Timer2 cannot operate in Sleep mode.
3: CKPOL should not be changed while ON = 1.
4: Setting this bit ensures glitch-free operation when the ON is enabled or disabled.
5: When this bit is set then the timer operation will be delayed by two TMR2 input clocks after the ON bit is set.
6: Unless otherwise indicated, all modes start upon ON = 1 and stop upon ON = 0 (stops occur without affecting the value
of TMR2).
7: When TMR2 = PR2, the next clock clears TMR2, regardless of the operating mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 354


PIC16(L)F15356/75/76/85/86

REGISTER 27-4: T2RST: TIMER2 EXTERNAL RESET SIGNAL SELECTION REGISTER


U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — RSEL<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 RSEL<3:0>: Timer2 External Reset Signal Source Selection bits
1111 = Reserved
1101 = LC4_out
1100 = LC3_out
1011 = LC2_out
1010 = LC1_out
1001 = ZCD1_output
1000 = C2OUT_sync
0111 = C1OUT_sync
0110 = PWM6_out
0101 = PWM5_out
0100 = PWM4_out
0011 = PWM3_out
0010 = CCP2_out
0001 = CCP1_out
0000 = T2INPPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 355


PIC16(L)F15356/75/76/85/86
TABLE 27-2: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER2
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
CCP1CON EN — OUT FMT MODE<3:0> 364
CCP2CON EN — OUT FMT MODE<3:0> 364
INTCON GIE PEIE — — — — — INTEDG 147
PIE4 — — — — — — TMR2IE TMR1IE 134
PIR4 — — — — — — TMR2IF TMR1IF 160
PR2 Timer2 Module Period Register 336*
TMR2 Holding Register for the 8-bit TMR2 Register 337*
T2CON ON CKPS<2:0> OUTPS<3:0> 353
T2CLKCON — — — — CS<3:0> 352
T2RST — — — — RSEL<3:0> 355
T2HLT PSYNC CKPOL CKSYNC MODE<4:0> 354
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used for Timer2 module.
* Page provides register information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 356


PIC16(L)F15356/75/76/85/86
28.0 CAPTURE/COMPARE/PWM
MODULES
The Capture/Compare/PWM module is a peripheral
that allows the user to time and control different events,
and to generate Pulse-Width Modulation (PWM)
signals. In Capture mode, the peripheral allows the
timing of the duration of an event. The Compare mode
allows the user to trigger an external event when a
predetermined amount of time has expired. The PWM
mode can generate Pulse-Width Modulated signals of
varying frequency and duty cycle.
The Capture/Compare/PWM modules available are
shown in Table 28-1.

TABLE 28-1: AVAILABLE CCP MODULES


Device CCP1 CCP2
PIC16(L)F15356/75/76/85/86 ● ●
The Capture and Compare functions are identical for all
CCP modules.
Note 1: In devices with more than one CCP
module, it is very important to pay close
attention to the register names used. A
number placed after the module acronym
is used to distinguish between separate
modules. For example, the CCP1CON
and CCP2CON control the same
operational aspects of two completely
different CCP modules.
2: Throughout this section, generic
references to a CCP module in any of its
operating modes may be interpreted as
being equally applicable to CCPx module.
Register names, module signals, I/O pins,
and bit names may use the generic
designator ‘x’ to indicate the use of a
numeral to distinguish a particular module,
when required.

 2016-2018 Microchip Technology Inc. DS40001866B-page 357


PIC16(L)F15356/75/76/85/86
28.1 Capture Mode Figure 28-1 shows a simplified diagram of the capture
operation.
Capture mode makes use of the 16-bit Timer1
resource. When an event occurs on the capture 28.1.1 CAPTURE SOURCES
source, the 16-bit CCPRxH:CCPRxL register pair
In Capture mode, the CCPx pin should be configured
captures and stores the 16-bit value of the
as an input by setting the associated TRIS control bit.
TMR1H:TMR1L register pair, respectively. An event is
defined as one of the following and is configured by the Note: If the CCPx pin is configured as an output,
CCPxMODE<3:0> bits of the CCPxCON register: a write to the port can cause a capture
• Every falling edge condition.
• Every rising edge The capture source is selected by configuring the
• Every 4th rising edge CCPxCTS<2:0> bits of the CCPxCAP register. The
following sources can be selected:
• Every 16th rising edge
• CCPxPPS input
When a capture is made, the Interrupt Request Flag bit
• C1OUT_sync
CCPxIF of the PIR6 register is set. The interrupt flag
• C2OUT_sync
must be cleared in software. If another capture occurs
• IOC_interrupt
before the value in the CCPRxH, CCPRxL register pair
• LC1_out
is read, the old captured value is overwritten by the new
• LC2_out
captured value.
• LC3_out
• LC4_out

FIGURE 28-1: CAPTURE MODE OPERATION BLOCK DIAGRAM

Rev. 10-000158F
9/1/2015
RxyPPS
CCPx
CTS<2:0>

TRIS Control
LC4_out 111
LC3_out 110 CCPRxH CCPRxL
LC2_out 101 16
set CCPxIF
LC1_out 100 Prescaler and
IOC_interrupt 011 1,4,16 Edge Detect
16
C2OUT_sync 010
C1OUT_sync 001 MODE <3:0> TMR1H TMR1L
CCPx PPS 000

CCPxPPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 358


PIC16(L)F15356/75/76/85/86
28.1.2 TIMER1 MODE RESOURCE 28.1.5 CAPTURE DURING SLEEP
Timer1 must be running in Timer mode or Synchronized Capture mode depends upon the Timer1 module for
Counter mode for the CCP module to use the capture proper operation. There are two options for driving the
feature. In Asynchronous Counter mode, the capture Timer1 module in Capture mode. It can be driven by the
operation may not work. instruction clock (FOSC/4), or by an external clock source.
See Section 26.0 “Timer1 Module with Gate When Timer1 is clocked by FOSC/4, Timer1 will not
Control” for more information on configuring Timer1. increment during Sleep. When the device wakes from
Sleep, Timer1 will continue from its previous state.
28.1.3 SOFTWARE INTERRUPT MODE
Capture mode will operate during Sleep when Timer1
When the Capture mode is changed, a false capture is clocked by an external clock source.
interrupt may be generated. The user should keep the
CCPxIE interrupt enable bit of the PIE6 register clear to 28.2 Compare Mode
avoid false interrupts. Additionally, the user should
clear the CCPxIF interrupt flag bit of the PIR6 register Compare mode makes use of the 16-bit Timer1
following any change in Operating mode. resource. The 16-bit value of the CCPRxH:CCPRxL
register pair is constantly compared against the 16-bit
Note: Clocking Timer1 from the system clock value of the TMR1H:TMR1L register pair. When a
(FOSC) should not be used in Capture match occurs, one of the following events can occur:
mode. In order for Capture mode to
recognize the trigger event on the CCPx • Toggle the CCPx output
pin, Timer1 must be clocked from the • Set the CCPx output
instruction clock (FOSC/4). • Clear the CCPx output
• Generate an Auto-conversion Trigger
28.1.4 CCP PRESCALER • Generate a Software Interrupt
There are four prescaler settings specified by the The action on the pin is based on the value of the
CCPxMODE<3:0> bits of the CCPxCON register. CCPxMODE<3:0> control bits of the CCPxCON
Whenever the CCP module is turned off, or the CCP register. At the same time, the interrupt flag CCPxIF bit
module is not in Capture mode, the prescaler counter is set, and an ADC conversion can be triggered, if
is cleared. Any Reset will clear the prescaler counter. selected.
Switching from one capture prescaler to another does not All Compare modes can generate an interrupt and
clear the prescaler and may generate a false interrupt. To trigger and ADC conversion.
avoid this unexpected operation, turn the module off by
clearing the CCPxCON register before changing the Figure 28-2 shows a simplified diagram of the compare
prescaler. Example 28-1 demonstrates the code to operation.
perform this function.
FIGURE 28-2: COMPARE MODE
EXAMPLE 28-1: CHANGING BETWEEN OPERATION BLOCK
CAPTURE PRESCALERS DIAGRAM
BANKSEL CCPxCON ;Set Bank bits to point CCPxMODE<3:0>
;to CCPxCON Mode Select
CLRF CCPxCON ;Turn CCP module off
MOVLW NEW_CAPT_PS ;Load the W reg with Set CCPxIF Interrupt Flag
;the new prescaler (PIR6)
CCPx 4
;move value and CCP ON Pin CCPRxH CCPRxL
MOVWF CCPxCON ;Load CCPxCON with this
Q S
;value Output Comparator
R Logic Match

TMR1H TMR1L
TRIS
Output Enable

Auto-conversion Trigger

 2016-2018 Microchip Technology Inc. DS40001866B-page 359


PIC16(L)F15356/75/76/85/86
28.2.1 CCPX PIN CONFIGURATION 28.3 PWM Overview
The software must configure the CCPx pin as an output Pulse-Width Modulation (PWM) is a scheme that
by clearing the associated TRIS bit and defining the provides power to a load by switching quickly between
appropriate output pin through the RxyPPS registers. fully on and fully off states. The PWM signal resembles
See Section 15.0 “Peripheral Pin Select (PPS) a square wave where the high portion of the signal is
Module” for more details. considered the on state and the low portion of the signal
The CCP output can also be used as an input for other is considered the off state. The high portion, also known
peripherals. as the pulse width, can vary in time and is defined in
steps. A larger number of steps applied, which
lengthens the pulse width, also supplies more power to
the load. Lowering the number of steps applied, which
Note: Clearing the CCPxCON register will force
shortens the pulse width, supplies less power. The
the CCPx compare output latch to the
PWM period is defined as the duration of one complete
default low level. This is not the PORT I/O
cycle or the total amount of on and off time combined.
data latch.
PWM resolution defines the maximum number of steps
28.2.2 TIMER1 MODE RESOURCE that can be present in a single PWM period. A higher
In Compare mode, Timer1 must be running in either resolution allows for more precise control of the pulse
Timer mode or Synchronized Counter mode. The width time and in turn the power that is applied to the
compare operation may not work in Asynchronous load.
Counter mode. The term duty cycle describes the proportion of the on
See Section 26.0 “Timer1 Module with Gate Control” time to the off time and is expressed in percentages,
for more information on configuring Timer1. where 0% is fully off and 100% is fully on. A lower duty
cycle corresponds to less power applied and a higher
Note: Clocking Timer1 from the system clock duty cycle corresponds to more power applied.
(FOSC) should not be used in Compare
Figure 28-3 shows a typical waveform of the PWM
mode. In order for Compare mode to
signal.
recognize the trigger event on the CCPx
pin, TImer1 must be clocked from the 28.3.1 STANDARD PWM OPERATION
instruction clock (FOSC/4) or from an
external clock source. The standard PWM mode generates a Pulse-Width
Modulation (PWM) signal on the CCPx pin with up to
28.2.3 AUTO-CONVERSION TRIGGER ten bits of resolution. The period, duty cycle, and
resolution are controlled by the following registers:
All CCPx modes set the CCP interrupt flag (CCPxIF).
When this flag is set and a match occurs, an Auto- • PR2 registers
conversion Trigger can take place if the CCP module is • T2CON registers
selected as the conversion trigger source. • CCPRxL registers
Refer to Section 20.2.4 “Auto-Conversion Trigger” • CCPxCON registers
for more information. Figure 28-4 shows a simplified block diagram of PWM
Note: Removing the match condition by operation.
changing the contents of the CCPRxH
and CCPRxL register pair, between the
Note: The corresponding TRIS bit must be
clock edge that generates the Auto-
cleared to enable the PWM output on the
conversion Trigger and the clock edge
CCPx pin.
that generates the Timer1 Reset, will
preclude the Reset from occurring
FIGURE 28-3: CCP PWM OUTPUT SIGNAL
28.2.4 COMPARE DURING SLEEP
Period
Since FOSC is shut down during Sleep mode, the
Compare mode will not function properly during Sleep, Pulse Width
unless the timer is running. The device will wake on TMR2 = PR2
interrupt (if enabled).
TMR2 = CCPRxH:CCPRxL

TMR2 = 0

 2016-2018 Microchip Technology Inc. DS40001866B-page 360


PIC16(L)F15356/75/76/85/86
FIGURE 28-4: SIMPLIFIED PWM BLOCK DIAGRAM
Rev. 10-000 157C

Duty cycle registers 9/5/201 4

CCPRxH CCPRxL
CCPx_out
To Peripherals
set CCPIF
10-bit Latch(2)
(Not accessible by user)

Comparator R Q PPS CCPx

S RxyPPS
TMR2 Module TRIS Control

R
TMR2 (1)

ERS logic
Comparator CCPx_pset

PR2

28.3.2 SETUP FOR PWM OPERATION 6. Enable PWM output pin:


The following steps should be taken when configuring •Wait until the Timer overflows and the TMR2IF
the CCP module for standard PWM operation: bit of the PIR4 register is set. See Note
below.
1. Use the desired output pin RxyPPS control to
•Enable the CCPx pin output driver by clearing
select CCPx as the source and disable the
the associated TRIS bit.
CCPx pin output driver by setting the associated
TRIS bit. Note: In order to send a complete duty cycle and
2. Load the PR2 register with the PWM period period on the first PWM output, the above
value. steps must be included in the setup
sequence. If it is not critical to start with a
3. Configure the CCP module for the PWM mode
complete PWM signal on the first output,
by loading the CCPxCON register with the
then step 6 may be ignored.
appropriate values.
4. Load the CCPRxL register, and the CCPRxH
28.3.3 CCP/PWM CLOCK SELECTION
register with the PWM duty cycle value and
configure the CCPxFMT bit of the CCPxCON The PIC16(L)F15356/75/76/85/86 allows each
register to set the proper register alignment. individual CCP and PWM module to select the timer
5. Configure and start Timer2: source that controls the module. Each module has an
independent selection.
•Clear the TMR2IF interrupt flag bit of the
PIR4 register. See Note below.
•Configure the CKPS bits of the T2CON reg-
ister with the Timer prescale value.
•Enable the Timer by setting the Timer2 ON
bit of the T2CON register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 361


PIC16(L)F15356/75/76/85/86
28.3.4 TIMER2 TIMER RESOURCE FIGURE 28-5: PWM 10-BIT ALIGNMENT
This device has a newer version of the Timer2 module Rev. 10-000 160A

that has many new modes, which allow for greater 12/9/201 3

customization and control of the PWM signals than on CCPRxH CCPRxL


older parts. Refer to Section 27.5 “Operation 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 FMT = 0
Examples” for examples of PWM signal generation
using the different modes of Timer2. The CCP CCPRxH CCPRxL
operation requires that the timer used as the PWM time FMT = 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
base has the FOSC/4 clock source selected

28.3.5 PWM PERIOD 10-bit Duty Cycle


The PWM period is specified by the PR2 register of 9 8 7 6 5 4 3 2 1 0
Timer2. The PWM period can be calculated using the
formula of Equation 28-1.

EQUATION 28-1: PWM PERIOD EQUATION 28-2: PULSE WIDTH

PWM Period =   PR2  + 1   4  T OSC  Pulse Width =  CCPRxH:CCPRxL register pair  


(TMR2 Prescale Value) T OSC  (TMR2 Prescale Value)

Note 1: TOSC = 1/FOSC


EQUATION 28-3: DUTY CYCLE RATIO
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
• TMR2 is cleared Duty Cycle Ratio = ---------------------------------------------------------------------------------
CCPRxH:CCPRxL register pair -
4  PR2 + 1 
• The CCPx pin is set. (Exception: If the PWM duty
cycle = 0%, the pin will not be set.)
CCPRxH:CCPRxL register pair are used to double
• The PWM duty cycle is transferred from the
buffer the PWM duty cycle. This double buffering
CCPRxL/H register pair into a 10-bit buffer.
provides for glitchless PWM operation.

Note: The Timer postscaler (see Section 27.4 The 8-bit timer TMR2 register is concatenated with
“Timer2 Interrupt”) is not used in the either the 2-bit internal system clock (FOSC), or two bits
of the prescaler, to create the 10-bit time base. The
determination of the PWM frequency.
system clock is used if the Timer2 prescaler is set to 1:1.
28.3.6 PWM DUTY CYCLE
When the 10-bit time base matches the
The PWM duty cycle is specified by writing a 10-bit CCPRxH:CCPRxL register pair, then the CCPx pin is
value to the CCPRxH:CCPRxL register pair. The cleared (see Figure 28-4).
alignment of the 10-bit value is determined by the
CCPRxFMT bit of the CCPxCON register (see 28.3.7 PWM RESOLUTION
Figure 28-5). The CCPRxH:CCPRxL register pair can
The resolution determines the number of available duty
be written to at any time; however the duty cycle value
cycles for a given period. For example, a 10-bit resolution
is not latched into the 10-bit buffer until after a match
will result in 1024 discrete duty cycles, whereas an 8-bit
between PR2 and TMR2.
resolution will result in 256 discrete duty cycles.
Equation 28-2 is used to calculate the PWM pulse
The maximum PWM resolution is ten bits when PR2 is
width.
255. The resolution is a function of the PR2 register
Equation 28-3 is used to calculate the PWM duty cycle value as shown by Equation 28-4.
ratio.
EQUATION 28-4: PWM RESOLUTION

log  4  PR2 + 1  - bits


Resolution = -----------------------------------------
log  2 

Note: If the pulse width value is greater than the


period the assigned PWM pin(s) will
remain unchanged.

 2016-2018 Microchip Technology Inc. DS40001866B-page 362


PIC16(L)F15356/75/76/85/86
TABLE 28-2: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 20 MHz)
PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz
Timer Prescale 16 4 1 1 1 1
PR2 Value 0xFF 0xFF 0xFF 0x3F 0x1F 0x17
Maximum Resolution (bits) 10 10 10 8 7 6.6

TABLE 28-3: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 8 MHz)


PWM Frequency 1.22 kHz 4.90 kHz 19.61 kHz 76.92 kHz 153.85 kHz 200.0 kHz
Timer Prescale 16 4 1 1 1 1
PR2 Value 0x65 0x65 0x65 0x19 0x0C 0x09
Maximum Resolution (bits) 8 8 8 6 5 5

28.3.8 OPERATION IN SLEEP MODE


In Sleep mode, the TMR2 register will not increment
and the state of the module will not change. If the CCPx
pin is driving a value, it will continue to drive that value.
When the device wakes up, TMR2 will continue from its
previous state.

28.3.9 CHANGES IN SYSTEM CLOCK


FREQUENCY
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 9.0 “Oscillator Module (with Fail-Safe
Clock Monitor)” for additional details.

28.3.10 EFFECTS OF RESET


Any Reset will force all ports to Input mode and the
CCP registers to their Reset states.

 2016-2018 Microchip Technology Inc. DS40001866B-page 363


PIC16(L)F15356/75/76/85/86
28.4 Register Definitions: CCP Control
Long bit name prefixes for the CCP peripherals are
shown in Section 1.1 “Register and Bit Naming
Conventions”.
TABLE 28-4: LONG BIT NAMES PREFIXES
FOR CCP PERIPHERALS
Peripheral Bit Name Prefix
CCP1 CCP1
CCP2 CCP2

REGISTER 28-1: CCPxCON: CCPx CONTROL REGISTER


R/W-0/0 U-0 R-x R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
EN — OUT FMT MODE<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Reset
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 EN: CCPx Module Enable bit


1 = CCPx is enabled
0 = CCPx is disabled
bit 6 Unimplemented: Read as ‘0’
bit 5 OUT: CCPx Output Data bit (read-only)
bit 4 FMT: CCPW (Pulse Width) Alignment bit
MODE = Capture mode
Unused
MODE = Compare mode
Unused
MODE = PWM mode
1 = Left-aligned format
0 = Right-aligned format
bit 3-0 MODE<3:0>: CCPx Mode Select bits(1)
1111 - 1100 = PWM mode (Timer2 as the timer source)
1110 = Reserved
1101 =Reserved
1100 = Reserved

1011 =Compare mode: output will pulse 0-1-0; Clears TMR1


1010 =Compare mode: output will pulse 0-1-0
1001 =Compare mode: clear output on compare match
1000 =Compare mode: set output on compare match

0111 =Capture mode: every 16th rising edge of CCPx input


0110 =Capture mode: every 4th rising edge of CCPx input
0101 =Capture mode: every rising edge of CCPx input
0100 =Capture mode: every falling edge of CCPx input

0011 =Capture mode: every edge of CCPx input


0010 =Compare mode: toggle output on match
0001 =Compare mode: toggle output on match; clear TMR1
0000 =Capture/Compare/PWM off (resets CCPx module)

Note 1: All modes will set the CCPxIF bit, and will trigger an ADC conversion if CCPx is selected as the ADC trigger source.

 2016-2018 Microchip Technology Inc. DS40001866B-page 364


PIC16(L)F15356/75/76/85/86
REGISTER 28-2: CCPxCAP: CAPTURE INPUT SELECTION REGISTER
U-0 U-0 U-0 U-0 U-0 R/W-0/x R/W-0/x R/W-0/x
— — — — — CTS<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Reset
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-3 Unimplemented: Read as ‘0’


bit 2-0 CTS<2:0>: Capture Trigger Input Selection bits

CTS CCP1.capture CCP2.capture


111 LC4_out
110 LC3_out
101 LC2_out
100 LC1_out
011 IOC_interrupt
010 C2OUT
001 C1OUT
000 CCP1PPS CCP2PPS

REGISTER 28-3: CCPRxL REGISTER: CCPx REGISTER LOW BYTE


R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x
CCPRx<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Reset
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 CCPxMODE = Capture mode


CCPRxL<7:0>: Capture value of TMR1L
CCPxMODE = Compare mode
CCPRxL<7:0>: LS Byte compared to TMR1L
CCPxMODE = PWM modes when CCPxFMT = 0:
CCPRxL<7:0>: Pulse-width Least Significant eight bits
CCPxMODE = PWM modes when CCPxFMT = 1:
CCPRxL<7:6>: Pulse-width Least Significant two bits
CCPRxL<5:0>: Not used.

 2016-2018 Microchip Technology Inc. DS40001866B-page 365


PIC16(L)F15356/75/76/85/86
REGISTER 28-4: CCPRxH REGISTER: CCPx REGISTER HIGH BYTE
R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x R/W-x/x
CCPRx<15:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Reset
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 CCPxMODE = Capture mode


CCPRxH<7:0>: Captured value of TMR1H
CCPxMODE = Compare mode
CCPRxH<7:0>: MS Byte compared to TMR1H
CCPxMODE = PWM modes when CCPxFMT = 0:
CCPRxH<7:2>: Not used
CCPRxH<1:0>: Pulse-width Most Significant two bits
CCPxMODE = PWM modes when CCPxFMT = 1:
CCPRxH<7:0>: Pulse-width Most Significant eight bits

 2016-2018 Microchip Technology Inc. DS40001866B-page 366


PIC16(L)F15356/75/76/85/86

TABLE 28-5: SUMMARY OF REGISTERS ASSOCIATED WITH CCPx


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
INTCON GIE PEIE — — — — — INTEDG 147
PIR6 — — — — — — CCP2IF CCP1IF 144
PIE6 — — — — — — CCP2IE CCP1IE 136
CCP1CON EN — OUT FMT MODE<3:0> 364
CCP1CAP — — — — — CTS<2:0> 365
CCPR1L Capture/Compare/PWM Register 1 (LSB) 365
CCPR1H Capture/Compare/PWM Register 1 (MSB) 366
CCP2CON EN — OUT FMT MODE<3:0> 364
CCP2CAP — — — — — CTS<2:0> 365
CCPR2L Capture/Compare/PWM Register 1 (LSB) 365
CCPR2H Capture/Compare/PWM Register 1 (MSB) 365
CCP1PPS — — CCP1PPS<5:0> 242
CCP2PPS — — CCP2PPS<5:0> 242
RxyPPS — — — RxyPPS<4:0> 243
ADACT — — — ADACT<4:0> 281
CLCxSELy — — — LCxDyS<4:0> 409
CWG1DAT — — — — DAT<3:0> 398
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the CCP module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 367


PIC16(L)F15356/75/76/85/86
29.0 PULSE-WIDTH MODULATION FIGURE 29-1: PWM OUTPUT
(PWM)
Q1 Q2 Q3 Q4 Rev. 10-000023C
8/26/2015

The PWMx modules generate Pulse-Width Modulated


(PWM) signals of varying frequency and duty cycle.
FOSC
In addition to the CCP modules, the PIC16(L)F15356/
75/76/85/86 devices contain four 10-bit PWM modules
Pulse Width
(PWM3, PWM4, PWM5 and PWM6). The PWM PWM
modules reproduce the PWM capability of the CCP TMRx = 0
(1)

modules.
(1)
TMRx = PWMxDC

Note: The PWM3/4/5/6 modules are four (1)


TMRx = PRx
instances of the same PWM module
design. Throughout this section, the lower
Note 1: Timer dependent on PWMTMRS register settings.
case ‘x’ in register and bit names is a
generic reference to the PWM module
number (which should be substituted with
3, or 4, or, 5 or 6 during code
development). For example, the control
register is generically described in this
chapter as PWMxCON, but the actual
device registers are PWM3CON,
PWM4CON, PWM5CON and
PWM6CON. Similarly, the PWMxEN bit
represents the PWM3EN, PWM4EN,
PWM5EN and PWM6EN bits.
Pulse-Width Modulation (PWM) is a scheme that
provides power to a load by switching quickly between
fully on and fully off states. The PWM signal resembles
a square wave where the high portion of the signal is
considered the ‘on’ state (pulse width), and the low
portion of the signal is considered the ‘off’ state. The
term duty cycle describes the proportion of the ‘on’ time
to the ‘off’ time and is expressed in percentages, where
0% is fully off and 100% is fully on. A lower duty cycle
corresponds to less power applied and a higher duty
cycle corresponds to more power applied. The PWM
period is defined as the duration of one complete cycle
or the total amount of on and off time combined.
PWM resolution defines the maximum number of steps
that can be present in a single PWM period. A higher
resolution allows for more precise control of the pulse
width time and, in turn, the power that is applied to the
load.
Figure 29-1 shows a typical waveform of the PWM
signal.

 2016-2018 Microchip Technology Inc. DS40001866B-page 368


PIC16(L)F15356/75/76/85/86
29.1 Standard PWM Mode
The standard PWM mode generates a Pulse-Width
Modulation (PWM) signal on the PWMx pin with up to
ten bits of resolution. The period, duty cycle, and
resolution are controlled by the following registers:
• TMR2 register
• PR2 register
• PWMxCON registers
• PWMxDCH registers
• PWMxDCL registers
Figure 29-2 shows a simplified block diagram of PWM
operation.
If PWMPOL = 0, the default state of the output is ‘0‘. If
PWMPOL = 1, the default state is ‘1’. If PWMEN = 0,
the output will be the default state.

Note: The corresponding TRIS bit must be


cleared to enable the PWM output on the
PWMx pin

FIGURE 29-2: SIMPLIFIED PWM BLOCK DIAGRAM

Rev. 10-000022B
9/24/2014

Duty cycle registers PWMxDCL<7:6>


PWMxDCH

PWMx_out
To Peripherals
10-bit Latch
(Not visible to user)

Comparator R Q
0
PPS PWMx
1
S Q
TMR2 Module
R PWMxPOL RxyPPS TRIS Control
TMR2 (1)

Comparator
T2_match

PR2

Note 1: 8-bit timer is concatenated with two bits generated by Fosc or two bits of the internal prescaler to
create 10-bit time-base.

 2016-2018 Microchip Technology Inc. DS40001866B-page 369


PIC16(L)F15356/75/76/85/86
29.1.1 PWM CLOCK SELECTION 29.1.4 PWM DUTY CYCLE
The PIC16(L)F15356/75/76/85/86 allows each individ- The PWM duty cycle is specified by writing a 10-bit
ual CCP and PWM module to select the timer source value to the PWMxDC register. The PWMxDCH
that controls the module. Each module has an indepen- contains the eight MSbs and the PWMxDCL<7:6> bits
dent selection. contain the two LSbs.
The PWMDC register is double-buffered and can be
29.1.2 USING THE TMR2 WITH THE PWM
updated at any time. This double buffering is essential
MODULE for glitch-free PWM operation. New values take effect
This device has a newer version of the TMR2 module when TMR2 = PR2. Note that PWMDC is left-justified.
that has many new modes, which allow for greater The 8-bit timer TMR2 register is concatenated with
customization and control of the PWM signals than on either the 2-bit internal system clock (FOSC), or two
older parts. Refer to Section 27.5 “Operation bits of the prescaler, to create the 10-bit time base. The
Examples” for examples of PWM signal generation system clock is used if the Timer2 prescaler is set to
using the different modes of Timer2. 1:1.
Equation 29-2 is used to calculate the PWM pulse
Note: PWM operation requires that the timer width.
used as the PWM time base has the Equation 29-3 is used to calculate the PWM duty cycle
FOSC/4 clock source selected. ratio.

29.1.3 PWM PERIOD EQUATION 29-2: PULSE WIDTH


Referring to Figure 29-1, the PWM output has a period
and a pulse width. The frequency of the PWM is the Pulse Widthൌሺܹܲ‫ܥܦݔܯ‬ሻ  ή ܱܶܵ‫ ܥ‬ή
inverse of the period (1/period). ሺܶ‫݁ݑ݈ܸ݈ܽ݁ܽܿݏ݁ݎܲʹܴܯ‬ሻ

The PWM period is specified by writing to the PR2


register. The PWM period can be calculated using the EQUATION 29-3: DUTY CYCLE RATIO
following formula:
ሺܹܲ‫ܥܦݔܯ‬ሻ
‫ ݋݅ݐܴ݈ܽ݁ܿݕܥݕݐݑܦ‬ൌ  
EQUATION 29-1: PWM PERIOD Ͷሺܴܲʹ ൅ ͳሻ

ܹܲ‫ ݀݋݅ݎ݁ܲܯ‬ൌ  ሾሺܴܲʹሻ  ൅ ͳሿ  ή Ͷ ή ܱܶܵ‫ܥ‬


ή  ሺܶ‫݁ݑ݈ܸ݈ܽ݁ܽܿݏ݁ݎܲʹܴܯ‬ሻ 29.1.5 PWM RESOLUTION
The resolution determines the number of available duty
Note 1: TOSC = 1/FOSC cycles for a given period. For example, a 10-bit
resolution will result in 1024 discrete duty cycles,
When TMR2 is equal to PR2, the following three events whereas an 8-bit resolution will result in 256 discrete
occur on the next increment cycle: duty cycles.
• TMR2 is cleared The maximum PWM resolution is ten bits when PR2 is
• The PWMx pin is set (Exception: If the PWM duty 255. The resolution is a function of the PR2 register
cycle = 0%, the pin will not be set.) value as shown by Equation 29-4.
• The PWM pulse width is latched from PWMxDC.
EQUATION 29-4: PWM RESOLUTION
Note: If the pulse width value is greater than the log  4  PR2 + 1  
period the assigned PWM pin(s) will Resolution = ------------------------------------------ bits
log  2 
remain unchanged.

 2016-2018 Microchip Technology Inc. DS40001866B-page 370


PIC16(L)F15356/75/76/85/86
29.1.6 OPERATION IN SLEEP MODE 29.1.8 EFFECTS OF RESET
In Sleep mode, the TMR2 register will not increment Any Reset will force all ports to Input mode and the
and the state of the module will not change. If the PWMx registers to their Reset states.
PWMx pin is driving a value, it will continue to drive that
value. When the device wakes up, TMR2 will continue
from its previous state.

29.1.7 CHANGES IN SYSTEM CLOCK


FREQUENCY
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 9.0 “Oscillator Module (with Fail-Safe
Clock Monitor)” for additional details.

TABLE 29-1: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 20 MHz)


PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz
Timer Prescale 16 4 1 1 1 1
PR2 Value 0xFF 0xFF 0xFF 0x3F 0x1F 0x17
Maximum Resolution (bits) 10 10 10 8 7 6.6

TABLE 29-2: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 8 MHz)


PWM Frequency 1.22 kHz 4.90 kHz 19.61 kHz 76.92 kHz 153.85 kHz 200.0 kHz
Timer Prescale 16 4 1 1 1 1
PR2 Value 0xFF 0xFF 0xFF 0x3F 0x1F 0x17
Maximum Resolution (bits) 10 10 10 8 7 6.6

29.1.9 SETUP FOR PWM OPERATION 6. Wait until the TMR2IF is set.
The following steps should be taken when configuring 7. When the TMR2IF flag bit is set:
the module for using the PWMx outputs: • Clear the associated TRIS bit(s) to enable the out-
put driver.
1. Disable the PWMx pin output driver(s) by setting
• Route the signal to the desired pin by configuring
the associated TRIS bit(s).
the RxyPPS register.
2. Configure the PWM output polarity by • Enable the PWMx module by setting the
configuring the PWMxPOL bit of the PWMxCON PWMxEN bit of the PWMxCON register.
register.
In order to send a complete duty cycle and period on
3. Load the PR2 register with the PWM period value,
the first PWM output, the above steps must be followed
as determined by Equation 29-1.
in the order given. If it is not critical to start with a
4. Load the PWMxDCH register and bits <7:6> of complete PWM signal, then the PWM module can be
the PWMxDCL register with the PWM duty cycle enabled during Step 2 by setting the PWMxEN bit of
value, as determined by Equation 29-2. the PWMxCON register.
5. Configure and start Timer2:
• Clear the TMR2IF interrupt flag bit of the PIR4
register.
• Select the Timer2 prescale value by configuring
the CKPS<2:0> bits of the T2CON register.
• Enable Timer2 by setting the Timer2 ON bit of the
T2CON register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 371


PIC16(L)F15356/75/76/85/86
29.2 Register Definitions: PWM Control

REGISTER 29-1: PWMxCON: PWM CONTROL REGISTER


R/W-0/0 U-0 R-0 R/W-0/0 U-0 U-0 U-0 U-0
PWMxEN — PWMxOUT PWMxPOL — — — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 PWMxEN: PWM Module Enable bit


1 = PWM module is enabled
0 = PWM module is disabled
bit 6 Unimplemented: Read as ‘0’
bit 5 PWMxOUT: PWM Module Output Level when Bit is Read
bit 4 PWMxPOL: PWMx Output Polarity Select bit
1 = PWM output is active-low
0 = PWM output is active-high
bit 3-0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 372


PIC16(L)F15356/75/76/85/86

REGISTER 29-2: PWMxDCH: PWM DUTY CYCLE HIGH BITS


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
PWMxDC<9:2>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 PWMxDC<9:2>: PWM Duty Cycle Most Significant bits


These bits are the MSbs of the PWM duty cycle. The two LSbs are found in PWMxDCL Register.

REGISTER 29-3: PWMxDCL: PWM DUTY CYCLE LOW BITS


R/W-x/u R/W-x/u U-0 U-0 U-0 U-0 U-0 U-0
PWMxDC<1:0> — — — — — —
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 PWMxDC<1:0>: PWM Duty Cycle Least Significant bits


These bits are the LSbs of the PWM duty cycle. The MSbs are found in PWMxDCH Register.
bit 5-0 Unimplemented: Read as ‘0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 373


PIC16(L)F15356/75/76/85/86

TABLE 29-3: SUMMARY OF REGISTERS ASSOCIATED WITH PWMx


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
T2CON ON CKPS<2:0> OUTPS<3:0> 353
T2TMR Holding Register for the 8-bit TMR2 Register 337*
T2PR TMR2 Period Register 336*
RxyPPS ― ― — RxyPPS<4:0> 243
CWG1DAT — — — — DAT<3:0> 398
CLCxSELy — — LCxDyS<5:0> 409
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 201
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 212
Legend: - = Unimplemented locations, read as ‘0’. Shaded cells are not used by the PWMx module.
* Page with Register information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 374


PIC16(L)F15356/75/76/85/86
30.0 COMPLEMENTARY WAVEFORM 30.1 Fundamental Operation
GENERATOR (CWG) MODULE The CWG module can operate in six different modes,
The Complementary Waveform Generator (CWG) as specified by MODE of the CWG1CON0 register:
produces half-bridge, full-bridge, and steering of PWM • Half-Bridge mode (Figure 30-9)
waveforms. It is backwards compatible with previous • Push-Pull mode (Figure 30-2)
ECCP functions. - Full-Bridge mode, Forward (Figure 30-3)
The CWG has the following features: - Full-Bridge mode, Reverse (Figure 30-3)
• Six operating modes: • Steering mode (Figure 30-10)
- Synchronous Steering mode • Synchronous Steering mode (Figure 30-11)
- Asynchronous Steering mode It may be necessary to guard against the possibility of
- Full-Bridge mode, Forward circuit faults or a feedback event arriving too late or not
- Full-Bridge mode, Reverse at all. In this case, the active drive must be terminated
- Half-Bridge mode before the Fault condition causes damage. Thus, all
output modes support auto-shutdown, which is covered
- Push-Pull mode
in 30.10 “Auto-Shutdown”.
• Output polarity control
• Output steering 30.1.1 HALF-BRIDGE MODE
- Synchronized to rising event In Half-Bridge mode, two output signals are generated
- Immediate effect as true and inverted versions of the input as illustrated
• Independent 6-bit rising and falling event dead- in Figure 30-9. A non-overlap (dead-band) time is
band timers inserted between the two outputs as described in
- Clocked dead band Section 30.5 “Dead-Band Control”.
- Independent rising and falling dead-band The unused outputs CWG1C and CWG1D drive similar
enables signals, with polarity independently controlled by the
• Auto-shutdown control with: POLC and POLD bits of the CWG1CON1 register,
respectively.
- Selectable shutdown sources
- Auto-restart enable
- Auto-shutdown pin override control
The CWG modules available are shown in Table 30-1.

TABLE 30-1: AVAILABLE CWG MODULES


Device CWG1
PIC16(L)F15356/75/76/85/86 ●

 2016-2018 Microchip Technology Inc. DS40001866B-page 375


FIGURE 30-1: SIMPLIFIED CWG BLOCK DIAGRAM (HALF-BRIDGE MODE)
 2016-2018 Microchip Technology Inc.

Rev. 10-000166B
8/29/2014

CWG_data

Rising Deadband Block


See clock CWG_dataA
CWGxISM signal_out
Register signal_in CWG_dataC

PIC16(L)F15356/75/76/85/86
D Q

CWGxISM<3:0>
E Q
R
Falling Deadband Block
clock CWG_dataB
signal_out
signal_in CWG_dataD
EN
SHUTDOWN

HFINTOSC 1
FOSC 0

CWGxCLK<0>
DS40001866B-page 376
PIC16(L)F15356/75/76/85/86
30.1.2 PUSH-PULL MODE
In Push-Pull mode, two output signals are generated,
alternating copies of the input as illustrated in
Figure 30-2. This alternation creates the push-pull
effect required for driving some transformer-based
power supply designs.
The push-pull sequencer is reset whenever EN = 0 or
if an auto-shutdown event occurs. The sequencer is
clocked by the first input pulse, and the first output
appears on CWG1A.
The unused outputs CWG1C and CWG1D drive copies
of CWG1A and CWG1B, respectively, but with polarity
controlled by the POLC and POLD bits of the
CWG1CON1 register, respectively.

30.1.3 FULL-BRIDGE MODES


In Forward and Reverse Full-Bridge modes, three out-
puts drive static values while the fourth is modulated by
the input data signal. In Forward Full-Bridge mode,
CWG1A is driven to its active state, CWG1B and
CWG1C are driven to their inactive state, and CWG1D
is modulated by the input signal. In Reverse Full-Bridge
mode, CWG1C is driven to its active state, CWG1A and
CWG1D are driven to their inactive states, and CWG1B
is modulated by the input signal. In Full-Bridge mode,
the dead-band period is used when there is a switch
from forward to reverse or vice-versa. This dead-band
control is described in Section 30.5 “Dead-Band Con-
trol”, with additional details in Section 30.6 “Rising
Edge and Reverse Dead Band” and Section 30.7
“Falling Edge and Forward Dead Band”.
The mode selection may be toggled between forward
and reverse toggling the MODE<0> bit of the
CWG1CON0 while keeping MODE<2:1> static, without
disabling the CWG module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 377


FIGURE 30-2: SIMPLIFIED CWG BLOCK DIAGRAM (PUSH-PULL MODE)
 2016-2018 Microchip Technology Inc.

Rev. 10-000167B
8/29/2014

CWG_data

See
CWGxISM
Register D Q

CWG_dataA
Q CWG_dataC
R

CWG_dataB
D Q

PIC16(L)F15356/75/76/85/86
CWG_dataD
CWGxISM<3:0>
E Q
R

EN
SHUTDOWN
DS40001866B-page 378
FIGURE 30-3: SIMPLIFIED CWG BLOCK DIAGRAM (FORWARD AND REVERSE FULL-BRIDGE MODES)
 2016-2018 Microchip Technology Inc.

Rev. 10-000165B
8/29/2014

MODE0 Reverse Deadband Block


clock
signal_out
See signal_in
CWGxISM
Register
CWG_dataA

D Q CWG_dataB

D Q
Q CWG_dataC

PIC16(L)F15356/75/76/85/86
CWGxISM<3:0>
E
R
Q CWG_dataD
clock
signal_out
signal_in
Forward Deadband Block
EN CWG_data
SHUTDOWN

HFINTOSC 1
FOSC 0

CWGxCLK<0>
DS40001866B-page 379
PIC16(L)F15356/75/76/85/86
30.1.4 STEERING MODES
In Steering modes, the data input can be steered to any
or all of the four CWG output pins. In Synchronous
Steering mode, changes to steering selection registers
take effect on the next rising input.
In Non-Synchronous mode, steering takes effect on the
next instruction cycle. Additional details are provided in
Section 30.9 “CWG Steering Mode”.

FIGURE 30-4: SIMPLIFIED CWG BLOCK DIAGRAM (OUTPUT STEERING MODES)


Rev. 10-000164B
8/26/2015

See
CWGxISM CWG_dataA
Register
CWG_dataB
CWG_data

CWG_dataC
CWG_dataD
D Q

CWGxISM <3:0>
E Q
R

EN
SHUTDOWN

30.2 Clock Source


The CWG module allows the following clock sources to
be selected:
• Fosc (system clock)
• HFINTOSC (16 MHz only)
The clock sources are selected using the CS bit of the
CWG1CLKCON register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 380


PIC16(L)F15356/75/76/85/86
30.3 Selectable Input Sources 30.4 Output Control
The CWG generates the output waveforms from the 30.4.1 POLARITY CONTROL
input sources in Table 30-2.
The polarity of each CWG output can be selected
independently. When the output polarity bit is set, the
TABLE 30-2: SELECTABLE INPUT
corresponding output is active-high. Clearing the
SOURCES
output polarity bit configures the corresponding output
Source Peripheral Signal Name as active-low. However, polarity does not affect the
override levels. Output polarity is selected with the
CWG input PPS pin CWG1PPS
POLx bits of the CWG1CON1. Auto-shutdown and
CCP1 CCP1_out steering options are unaffected by polarity.
CCP2 CCP2_out
PWM3 PWM3_out
PWM4 PWM4_out
PWM5 PWM5_out
PWM6 PWM6_out
NCO NCO1_out
Comparator C1 C1OUT_sync
Comparator C2 C2OUT_sync
CLC1 LC1_out
CLC2 LC2_out
CLC3 LC3_out
CLC4 LC4_out
The input sources are selected using the CWG1DAT
register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 381


PIC16(L)F15356/75/76/85/86
FIGURE 30-5: CWG OUTPUT BLOCK DIAGRAM

Rev. 10-000171B
9/24/2014

LSAC<1:0>

‘1’ 11 RxyPPS
TRIS Control
‘0’ 10
1
CWG_dataA High Z 01 PPS CWGxA
1 0
POLA 00
OVRA 0

STRA(1)

LSBD<1:0>

‘1’ 11 RxyPPS
TRIS Control
‘0’ 10
1
CWG_dataB High Z 01 PPS CWGxB
1 0
POLB 00
OVRB 0

STRB(1)

LSAC<1:0>

‘1’ 11 RxyPPS
TRIS Control
‘0’ 10
1
CWG_dataC High Z 01 PPS CWGxC
1 0
POLC 00
OVRC 0

STRC(1)

LSBD<1:0>

‘1’ 11 RxyPPS
TRIS Control
‘0’ 10
1
CWG_dataD High Z 01 PPS CWGxD
1 0
POLD 00
OVRD 0

STRD(1)

CWG_shutdown

Note 1: STRx is held to 1 in all modes other than Output Steering Mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 382


PIC16(L)F15356/75/76/85/86
30.5 Dead-Band Control 30.6 Rising Edge and Reverse Dead
The dead-band control provides non-overlapping PWM
Band
signals to prevent shoot-through current in PWM CWG1DBR controls the rising edge dead-band time at
switches. Dead-band operation is employed for Half- the leading edge of CWG1A (Half-Bridge mode) or the
Bridge and Full-Bridge modes. The CWG contains two leading edge of CWG1B (Full-Bridge mode). The
6-bit dead-band counters. One is used for the rising CWG1DBR value is double-buffered. When EN = 0,
edge of the input source control in Half-Bridge mode or the CWG1DBR register is loaded immediately when
for reverse dead-band Full-Bridge mode. The other is CWG1DBR is written. When EN = 1, then software
used for the falling edge of the input source control in must set the LD bit of the CWG1CON0 register, and the
Half-Bridge mode or for forward dead band in Full- buffer will be loaded at the next falling edge of the CWG
Bridge mode. input signal. If the input source signal is not present for
Dead band is timed by counting CWG clock periods enough time for the count to be completed, no output
from zero up to the value in the rising or falling dead- will be seen on the respective output.
band counter registers. See CWG1DBR and
CWG1DBF registers, respectively. 30.7 Falling Edge and Forward Dead
Band
30.5.1 DEAD-BAND FUNCTIONALITY IN
HALF-BRIDGE MODE CWG1DBF controls the dead-band time at the leading
In Half-Bridge mode, the dead-band counters dictate edge of CWG1B (Half-Bridge mode) or the leading
the delay between the falling edge of the normal output edge of CWG1D (Full-Bridge mode). The CWG1DBF
and the rising edge of the inverted output. This can be value is double-buffered. When EN = 0, the
seen in Figure 30-9. CWG1DBF register is loaded immediately when
CWG1DBF is written. When EN = 1 then software
30.5.2 DEAD-BAND FUNCTIONALITY IN must set the LD bit of the CWG1CON0 register, and
FULL-BRIDGE MODE the buffer will be loaded at the next falling edge of the
In Full-Bridge mode, the dead-band counters are used CWG input signal. If the input source signal is not
when undergoing a direction change. The MODE<0> present for enough time for the count to be completed,
bit of the CWG1CON0 register can be set or cleared no output will be seen on the respective output.
while the CWG is running, allowing for changes from Refer to Figure 30-6 and Figure 30-7 for examples.
Forward to Reverse mode. The CWG1A and CWG1C
signals will change upon the first rising input edge
following a direction change, but the modulated signals
(CWG1B or CWG1D, depending on the direction of the
change) will experience a delay dictated by the dead-
band counters. This is demonstrated in Figure 30-3.

 2016-2018 Microchip Technology Inc. DS40001866B-page 383


FIGURE 30-6: DEAD-BAND OPERATION CWG1DBR = 01H, CWG1DBF = 02H
 2016-2018 Microchip Technology Inc.

cwg_clock

Input Source

CWG1A

CWG1B

PIC16(L)F15356/75/76/85/86
FIGURE 30-7: DEAD-BAND OPERATION, CWG1DBR = 03H, CWG1DBF = 04H, SOURCE SHORTER THAN DEAD BAND

cwg_clock

Input Source

CWG1A

CWG1B

source shorter than dead band


DS40001866B-page 384
PIC16(L)F15356/75/76/85/86
30.8 Dead-Band Uncertainty EQUATION 30-1: DEAD-BAND
UNCERTAINTY
When the rising and falling edges of the input source
are asynchronous to the CWG clock, it creates uncer-
tainty in the dead-band time delay. The maximum 1
TDEADBAND_UNCERTAINTY = -----------------------------
uncertainty is equal to one CWG clock period. Refer to Fcwg_clock
Equation 30-1 for more details.
Example:
FCWG_CLOCK = 16 MHz

Therefore:
1
TDEADBAND_UNCERTAINTY = ----------------------------
-
Fcwg_clock

1 -
= -----------------
16MHz

= 62.5ns

FIGURE 30-8: EXAMPLE OF PWM DIRECTION CHANGE

MODE0

CWG1A

CWG1B

CWG1C

CWG1D

No delay CWG1DBR No delay CWG1DBF


CWG1_data

Note 1: WGPOL{ABCD} = 0
2: The direction bit MODE<0> (Register 30-1) can be written any time during the PWM cycle, and takes effect at the
next rising CWG1_data.
3: When changing directions, CWG1A and CWG1C switch at rising CWG1_data; modulated CWG1B and CWG1D
are held inactive for the dead band duration shown; dead band affects only the first pulse after the direction change.

 2016-2018 Microchip Technology Inc. DS40001866B-page 385


PIC16(L)F15356/75/76/85/86
FIGURE 30-9: CWG HALF-BRIDGE MODE OPERATION

CWG1_clock

CWG1A
CWG1C
Rising Event Dead Band Rising Event D
Falling Event Dead Band Falling Event Dead Band
CWG1B
CWG1D

CWG1_data
Note: CWG1_rising_src = CCP1_out, CWG1_falling_src = ~CCP1_out

 2016-2018 Microchip Technology Inc. DS40001866B-page 386


PIC16(L)F15356/75/76/85/86
30.9 CWG Steering Mode 30.9.1 STEERING SYNCHRONIZATION
In Steering mode (MODE = 00x), the CWG allows any Changing the MODE bits allows for two modes of
combination of the CWG1x pins to be the modulated steering, synchronous and asynchronous.
signal. The same signal can be simultaneously avail- When MODE = 000, the steering event is asynchro-
able on multiple pins, or a fixed-value output can be nous and will happen at the end of the instruction that
presented. writes to STRx (that is, immediately). In this case, the
When the respective STRx bit of CWG1OCON0 is ‘0’, output signal at the output pin may be an incomplete
the corresponding pin is held at the level defined. When waveform. This can be useful for immediately removing
the respective STRx bit of CWG1OCON0 is ‘1’, the pin a signal from the pin.
is driven by the input data signal. The user can assign When MODE = 001, the steering update is synchro-
the input data signal to one, two, three, or all four output nous and occurs at the beginning of the next rising
pins. edge of the input data signal. In this case, steering the
The POLx bits of the CWG1CON1 register control the output on/off will always produce a complete waveform.
signal polarity only when STRx = 1. Figure 30-10 and Figure 30-11 illustrate the timing of
The CWG auto-shutdown operation also applies in asynchronous and synchronous steering, respectively.
Steering modes as described in Section 30.10 “Auto-
Shutdown”. An auto-shutdown event will only affect
pins that have STRx = 1.

FIGURE 30-10: EXAMPLE OF ASYNCHRONOUS STEERING EVENT (MODE<2:0> = 000)

Rising Event

CWG1_data
(Rising and Falling Source)

STR<D:A>

CWG1<D:A> OVR<D:A> OVR<D:A> Data

follows CWG1_data

FIGURE 30-11: EXAMPLE OF STEERING EVENT (MODE<2:0> = 001)

CWG1_data
(Rising and Falling Source)

STR<D:A>

CWG1<D:A> OVR<D:A> Data OVR<D:A> Data

follows CWG1_data

 2016-2018 Microchip Technology Inc. DS40001866B-page 387


PIC16(L)F15356/75/76/85/86
30.10 Auto-Shutdown 30.11 Operation During Sleep
Auto-shutdown is a method to immediately override the The CWG module operates independently from the
CWG output levels with specific overrides that allow for system clock and will continue to run during Sleep,
safe shutdown of the circuit. The shutdown state can be provided that the clock and input sources selected
either cleared automatically or held until cleared by remain active.
software. The auto-shutdown circuit is illustrated in The HFINTOSC remains active during Sleep when all
Figure 30-12. the following conditions are met:
30.10.1 SHUTDOWN • CWG module is enabled
The shutdown state can be entered by either of the • Input source is active
following two methods: • HFINTOSC is selected as the clock source,
regardless of the system clock source selected.
• Software generated
• External Input In other words, if the HFINTOSC is simultaneously
selected as the system clock and the CWG clock
30.10.1.1 Software Generated Shutdown source, when the CWG is enabled and the input source
is active, then the CPU will go idle during Sleep, but the
Setting the SHUTDOWN bit of the CWG1AS0 register HFINTOSC will remain active and the CWG will con-
will force the CWG into the shutdown state. tinue to operate. This will have a direct effect on the
When the auto-restart is disabled, the shutdown state Sleep mode current.
will persist as long as the SHUTDOWN bit is set.
When auto-restart is enabled, the SHUTDOWN bit will
clear automatically and resume operation on the next
rising edge event.

30.10.2 EXTERNAL INPUT SOURCE


External shutdown inputs provide the fastest way to
safely suspend CWG operation in the event of a Fault
condition. When any of the selected shutdown inputs
goes active, the CWG outputs will immediately go to the
selected override levels without software delay. Several
input sources can be selected to cause a shutdown con-
dition. All input sources are active-low. The sources are:
• Comparator C1OUT_sync
• Comparator C2OUT_sync
• Timer2 – TMR2_postscaled
• CWG1IN input pin
Shutdown inputs are selected using the CWG1AS1
register (Register 30-6).
Note: Shutdown inputs are level sensitive, not
edge sensitive. The shutdown state can-
not be cleared, except by disabling auto-
shutdown, as long as the shutdown input
level persists.

 2016-2018 Microchip Technology Inc. DS40001866B-page 388


FIGURE 30-12: CWG SHUTDOWN BLOCK DIAGRAM
 2016-2018 Microchip Technology Inc.

Write ‘1’ to Rev. 10-000172F


3/14/2017
SHUTDOWN bit

PPS
INAS
CWGxINPPS
C1OUT_sync
C1AS

C2OUT_sync
C2AS

TMR2_postscaled SHUTDOWN S
S Q
TMR2AS
D Q CWG_shutdown
REN FREEZE
R
Write ‘0’ to
SHUTDOWN bit
CWG_data CK

PIC16(L)F15356/75/76/85/86
DS40001866B-page 389
PIC16(L)F15356/75/76/85/86
30.12 Configuring the CWG 30.12.2 AUTO-SHUTDOWN RESTART
The following steps illustrate how to properly configure After an auto-shutdown event has occurred, there are
the CWG. two ways to resume operation:

1. Ensure that the TRIS control bits corresponding • Software controlled


to the desired CWG pins for your application are • Auto-restart
set so that the pins are configured as inputs. The restart method is selected with the REN bit of the
2. Clear the EN bit, if not already cleared. CWG1CON2 register. Waveforms of software con-
3. Set desired mode of operation with the MODE trolled and automatic restarts are shown in Figure 30-13
bits. and Figure 30-14.
4. Set desired dead-band times, if applicable to
mode, with the CWG1DBR and CWG1DBF 30.12.2.1 Software Controlled Restart
registers. When the REN bit of the CWG1AS0 register is cleared,
5. Setup the following controls in the CWG1AS0 the CWG must be restarted after an auto-shutdown
and CWG1AS1 registers. event by software. Clearing the shutdown state
requires all selected shutdown inputs to be low, other-
a. Select the desired shutdown source.
wise the SHUTDOWN bit will remain set. The overrides
b. Select both output overrides to the desired will remain in effect until the first rising edge event after
levels (this is necessary even if not using auto- the SHUTDOWN bit is cleared. The CWG will then
shutdown because start-up will be from a shut- resume operation.
down state).
c. Set which pins will be affected by auto-shut- 30.12.2.2 Auto-Restart
down with the CWG1AS1 register. When the REN bit of the CWG1CON2 register is set,
d. Set the SHUTDOWN bit and clear the REN bit. the CWG will restart from the auto-shutdown state
automatically. The SHUTDOWN bit will clear automati-
6. Select the desired input source using the cally when all shutdown sources go low. The overrides
CWG1DAT register. will remain in effect until the first rising edge event after
7. Configure the following controls. the SHUTDOWN bit is cleared. The CWG will then
a. Select desired clock source using the resume operation.
CWG1CLKCON register.
b. Select the desired output polarities using the
CWG1CON1 register.
c. Set the output enables for the desired outputs.
8. Set the EN bit.
9. Clear TRIS control bits corresponding to the
desired output pins to configure these pins as
outputs.
10. If auto-restart is to be used, set the REN bit and
the SHUTDOWN bit will be cleared automati-
cally. Otherwise, clear the SHUTDOWN bit to
start the CWG.

30.12.1 PIN OVERRIDE LEVELS


The levels driven to the output pins, while the shutdown
input is true, are controlled by the LSBD and LSAC bits
of the CWG1AS0 register. LSBD<1:0> controls the
CWG1B and D override levels and LSAC<1:0> controls
the CWG1A and C override levels. The control bit logic
level corresponds to the output logic drive level while in
the shutdown state. The polarity control does not affect
the override level.

 2016-2018 Microchip Technology Inc. DS40001866B-page 390


FIGURE 30-13: SHUTDOWN FUNCTIONALITY, AUTO-RESTART DISABLED (REN = 0, LSAC = 01, LSBD = 01)
 2016-2018 Microchip Technology Inc.

Shutdown Event Ceases REN Cleared by Software

CWG Input
Source

Shutdown Source

SHUTDOWN

CWG1A Tri-State (No Pulse)


CWG1C

CWG1B Tri-State (No Pulse)


CWG1D

PIC16(L)F15356/75/76/85/86
No Shutdown
Shutdown Output Resumes

FIGURE 30-14: SHUTDOWN FUNCTIONALITY, AUTO-RESTART ENABLED (REN = 1, LSAC = 01, LSBD = 01)

Shutdown Event Ceases REN auto-cleared by hardware

CWG Input
Source

Shutdown Source

SHUTDOWN

CWG1A Tri-State (No Pulse)


DS40001866B-page 391

CWG1C

CWG1B Tri-State (No Pulse)


CWG1D
No Shutdown
Shutdown Output Resumes
PIC16(L)F15356/75/76/85/86
30.13 Register Definitions: CWG Control
Long bit name prefixes for the CWG peripherals are
shown in Section 1.1 “Register and Bit Naming
Conventions”.

REGISTER 30-1: CWG1CON0: CWG1 CONTROL REGISTER 0


R/W-0/0 R/W/HC-0/0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
EN LD(1) — — — MODE<2:0>
bit 7 bit 0

Legend:
HC = Bit is cleared by hardware HS = Bit is set by hardware
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 EN: CWG1 Enable bit


1 = Module is enabled
0 = Module is disabled
bit 6 LD: CWG1 Load Buffer bits(1)
1 = Buffers to be loaded on the next rising/falling event
0 = Buffers not loaded
bit 5-3 Unimplemented: Read as ‘0’
bit 2-0 MODE<2:0>: CWG1 Mode bits
111 = Reserved
110 = Reserved
101 = CWG outputs operate in Push-Pull mode
100 = CWG outputs operate in Half-Bridge mode
011 = CWG outputs operate in Reverse Full-Bridge mode
010 = CWG outputs operate in Forward Full-Bridge mode
001 = CWG outputs operate in Synchronous Steering mode
000 = CWG outputs operate in Steering mode

Note 1: This bit can only be set after EN = 1 and cannot be set in the same instruction that EN is set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 392


PIC16(L)F15356/75/76/85/86

REGISTER 30-2: CWG1CON1: CWG1 CONTROL REGISTER 1


U-0 U-0 R-x U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — IN — POLD POLC POLB POLA
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-6 Unimplemented: Read as ‘0’


bit 5 IN: CWG Input Value bit
bit 4 Unimplemented: Read as ‘0’
bit 3 POLD: CWG1D Output Polarity bit
1 = Signal output is inverted polarity
0 = Signal output is normal polarity
bit 2 POLC: CWG1C Output Polarity bit
1 = Signal output is inverted polarity
0 = Signal output is normal polarity
bit 1 POLB: CWG1B Output Polarity bit
1 = Signal output is inverted polarity
0 = Signal output is normal polarity
bit 0 POLA: CWG1A Output Polarity bit
1 = Signal output is inverted polarity
0 = Signal output is normal polarity

 2016-2018 Microchip Technology Inc. DS40001866B-page 393


PIC16(L)F15356/75/76/85/86

REGISTER 30-3: CWG1DBR: CWG1 RISING DEAD-BAND COUNTER REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — DBR<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 DBR<5:0>: Rising Event Dead-Band Value for Counter bits

REGISTER 30-4: CWG1DBF: CWG1 FALLING DEAD-BAND COUNTER REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — DBF<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 DBF<5:0>: Falling Event Dead-Band Value for Counter bits

 2016-2018 Microchip Technology Inc. DS40001866B-page 394


PIC16(L)F15356/75/76/85/86

REGISTER 30-5: CWG1AS0: CWG1 AUTO-SHUTDOWN CONTROL REGISTER 0


R/W/HS-0/0 R/W-0/0 R/W-0/0 R/W-1/1 R/W-0/0 R/W-1/1 U-0 U-0
SHUTDOWN(1, 2) REN LSBD<1:0> LSAC<1:0> — —
bit 7 bit 0

Legend:
HC = Bit is cleared by hardware HS = Bit is set by hardware
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 SHUTDOWN: Auto-Shutdown Event Status bit(1, 2)


1 = An Auto-Shutdown state is in effect
0 = No Auto-shutdown event has occurred
bit 6 REN: Auto-Restart Enable bit
1 = Auto-restart enabled
0 = Auto-restart disabled
bit 5-4 LSBD<1:0>: CWG1B and CWG1D Auto-Shutdown State Control bits
11 =A logic ‘1’ is placed on CWG1B/D when an auto-shutdown event is present
10 =A logic ‘0’ is placed on CWG1B/D when an auto-shutdown event is present
01 =Pin is tri-stated on CWG1B/D when an auto-shutdown event is present
00 =The inactive state of the pin, including polarity, is placed on CWG1B/D after the required dead-
band interval
bit 3-2 LSAC<1:0>: CWG1A and CWG1C Auto-Shutdown State Control bits
11 =A logic ‘1’ is placed on CWG1A/C when an auto-shutdown event is present
10 =A logic ‘0’ is placed on CWG1A/C when an auto-shutdown event is present
01 =Pin is tri-stated on CWG1A/C when an auto-shutdown event is present
00 =The inactive state of the pin, including polarity, is placed on CWG1A/C after the required dead-
band interval
bit 1-0 Unimplemented: Read as ‘0’

Note 1: This bit may be written while EN = 0 (CWG1CON0 register) to place the outputs into the shutdown
configuration.
2: The outputs will remain in auto-shutdown state until the next rising edge of the input signal after this bit is
cleared.

 2016-2018 Microchip Technology Inc. DS40001866B-page 395


PIC16(L)F15356/75/76/85/86

REGISTER 30-6: CWG1AS1: CWG1 AUTO-SHUTDOWN CONTROL REGISTER 1


U-1 U-1 U-1 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — AS4E AS3E AS2E AS1E AS0E
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-5 Unimplemented: Read as ‘0’


bit 4 AS4E: CLC2 Output bit
1 = LC2_out shut-down is enabled
0 = LC2_out shut-down is disabled
bit 3 AS3E: Comparator C2 Output bit
1 = C2 output shut-down is enabled
0 = C2 output shut-down is disabled
bit 2 AS2E: Comparator C1 Output bit
1 = C1 output shut-down is enabled
0 = C1 output shut-down is disabled
bit 2 AS1E: TMR2 Postscale Output bit
1 = TMR2 Postscale shut-down is enabled
0 = TMR2 Postscale shut-down is disabled
bit 0 AS0E: CWG1 Input Pin bit
1 = Input pin selected by CWG1PPS shut-down is enabled
0 = Input pin selected by CWG1PPS shut-down is disabled

 2016-2018 Microchip Technology Inc. DS40001866B-page 396


PIC16(L)F15356/75/76/85/86

REGISTER 30-7: CWG1STR: CWG1 STEERING CONTROL REGISTER(1)


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
OVRD OVRC OVRB OVRA STRD(2) STRC(2) STRB(2) STRA(2)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7 OVRD: Steering Data D bit


bit 6 OVRC: Steering Data C bit
bit 5 OVRB: Steering Data B bit
bit 4 OVRA: Steering Data A bit
bit 3 STRD: Steering Enable D bit(2)
1 = CWG1D output has the CWG1_data waveform with polarity control from POLD bit
0 = CWG1D output is assigned the value of OVRD bit
bit 2 STRC: Steering Enable C bit(2)
1 = CWG1C output has the CWG1_data waveform with polarity control from POLC bit
0 = CWG1C output is assigned the value of OVRC bit
bit 1 STRB: Steering Enable B bit(2)
1 = CWG1B output has the CWG1_data waveform with polarity control from POLB bit
0 = CWG1B output is assigned the value of OVRB bit
bit 0 STRA: Steering Enable A bit(2)
1 = CWG1A output has the CWG1_data waveform with polarity control from POLA bit
0 = CWG1A output is assigned the value of OVRA bit

Note 1: The bits in this register apply only when MODE<2:0> = 00x.
2: This bit is effectively double-buffered when MODE<2:0> = 001.

 2016-2018 Microchip Technology Inc. DS40001866B-page 397


PIC16(L)F15356/75/76/85/86

REGISTER 30-8: CWG1CLK: CWG1 CLOCK SELECTION REGISTER


U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0
— — — — — — — CS
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-1 Unimplemented: Read as ‘0’


bit 0 CS: CWG1 Clock Selection bit
1 = HFINTOSC 16 MHz is selected
0 = FOSC is selected

REGISTER 30-9: CWG1DAT: CWG1 INPUT SELECTION REGISTER


U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — DAT<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 DAT<3:0>: CWG1 Input Selection bits
1111 =Reserved. No channel connected.
1110 =Reserved. No channel connected.
1101 =LC4_out
1100 =LC3_out
1011 =LC2_out
1010 =LC1_out
1001 =Comparator C2 out
1000 =Comparator C1 out
0111 =NCO1 output
0110 =PWM6_out
0101 =PWM5_out
0100 =PWM4_out
0011 =PWM3_out
0010 =CCP2_out
0001 =CCP1_out
0000 =CWG11CLK

 2016-2018 Microchip Technology Inc. DS40001866B-page 398


PIC16(L)F15356/75/76/85/86
TABLE 30-3: SUMMARY OF REGISTERS ASSOCIATED WITH CWG
Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

CWG1CLKCON — — — — — — — CS 398
CWG1DAT — — — — DAT<3:0> 398
CWG1DBR — — DBR<5:0> 394
CWG1DBF — — DBF<5:0> 394
CWG1CON0 EN LD — — — MODE<2:0> 397
CWG1CON1 — — IN — POLD POLC POLB POLA 393
CWG1AS0 SHUTDOWN REN LSBD<1:0> LSAC<1:0> — — 395
CWG1AS1 — — — AS4E AS3E AS2E AS1E AS0E 396
CWG1STR OVRD OVRC OVRB OVRA STRD STRC STRB STRA 397
Legend: – = unimplemented locations read as ‘0’. Shaded cells are not used by CWG.

 2016-2018 Microchip Technology Inc. DS40001866B-page 399


PIC16(L)F15356/75/76/85/86
31.0 CONFIGURABLE LOGIC CELL Refer to Figure 31-1 for a simplified diagram showing
signal flow through the CLCx.
(CLC)
Possible configurations include:
The Configurable Logic Cell (CLCx) module provides
programmable logic that operates outside the speed • Combinatorial Logic
limitations of software execution. The logic cell selects - AND
from 40 input signals and, through the use of - NAND
configurable gates, reduces the inputs to four logic - AND-OR
lines that drive one of eight selectable single-output - AND-OR-INVERT
logic functions.
- OR-XOR
Input sources are a combination of the following: - OR-XNOR
• I/O pins • Latches
• Internal clocks - S-R
• Peripherals - Clocked D with Set and Reset
• Register bits - Transparent D with Set and Reset
The output can be directed internally to peripherals and - Clocked J-K with Reset
to an output pin.
The CLC modules available are shown in Table 31-1.

TABLE 31-1: AVAILABLE CLC MODULES


Device CLC1 CLC2 CLC3 CLC4
PIC16(L)F15356/75/76/85/ ● ● ● ●
86

Note: The CLC1, CLC2, CLC3 and CLC4 are


four separate module instances of the
same CLC module design. Throughout
this section, the lower case ‘x’ in register
and bit names is a generic reference to
the CLC number (which should be substi-
tuted with 1, 2, 3, or 4 during code devel-
opment). For example, the control register
is generically described in this chapter as
CLCxCON, but the actual device registers
are CLC1CON, CLC2CON, CLC3CON
and CLC4CON. Similarly, the LCxEN bit
represents the LC1EN, LC2EN, LC3EN
and LC4EN bits.

 2016-2018 Microchip Technology Inc. DS40001866B-page 400


PIC16(L)F15356/75/76/85/86
FIGURE 31-1: CLCx SIMPLIFIED BLOCK DIAGRAM

Rev. 10-000025H
11/9/2016

OUT
D Q
CLCxOUT

Q1
LCx_in[0]
LCx_in[1] CLCx_out
to Peripherals
LCx_in[2]
Input Data Selection Gates(1)

. lcxg1
EN
CLCxPPS

. lcxg2

lcxg3
Logic
Function
(2)
lcxq
PPS CLCx

. lcxg4
POL TRIS

LCx_in[n-2] MODE<2:0> Interrupt


LCx_in[n-1] det
LCx_in[n]
INTP
set bit
INTN CLCxIF
Interrupt
det

Note 1: See Figure 31-2: Input Data Selection and Gating.


2: See Figure 31-3: Programmable Logic Functions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 401


PIC16(L)F15356/75/76/85/86
31.1 CLCx Setup TABLE 31-2: CLCx DATA INPUT SELECTION
Programming the CLCx module is performed by LCxDyS<5:0>
CLCx Input Source
Value
configuring the four stages in the logic signal flow. The
four stages are: 101000 to 111111 [40+] Reserved
100111 [39] CWG1B output
• Data selection
100110 [38] CWG1A output
• Data gating
100101 [37] MSSP2 SCK output
• Logic function selection 100100 [36] MSSP2 SDO output
• Output polarity 100011 [35] MSSP1 SCK output
Each stage is setup at run time by writing to the corre- 100010 [34] MSSP1 SDO output
sponding CLCx Special Function Registers. This has 100001 [33] EUSART2 (TX/CK) output
the added advantage of permitting logic reconfiguration 100000 [32] EUSART2 (DT) output
on-the-fly during program execution. 011111 [31] EUSART1 (TX/CK) output
011110 [30] EUSART1 (DT) output
31.1.1 DATA SELECTION
011101 [29] CLC4 output
There are 40 signals available as inputs to the 011100 [28] CLC3 output
configurable logic. Four 40-input multiplexers are used 011011 [27] CLC2 output
to select the inputs to pass on to the next stage.
011010 [26] CLC1 output
Data selection is through four multiplexers as indicated 011001 [25] IOCIF
on the left side of Figure 31-2. Data inputs in the figure 011000 [24] ZCD output
are identified by a generic numbered input name. 010111 [23] C2OUT
Table 31-2 correlates the generic input name to the 010110 [22] C1OUT
actual signal for each CLC module. The column labeled 010101 [21] NCO1 output
‘LCxDyS<5:0> Value’ indicates the MUX selection code 010100 [20] PWM6 output
for the selected data input. LCxDyS is an abbreviation to 010011 [19] PWM5 output
identify specific multiplexers: LCxD1S<5:0> through
010010 [18] PWM4 output
LCxD4S<5:0>.
010001 [17] PWM3 output
Data inputs are selected with CLCxSEL0 through 010000 [16] CCP2 output
CLCxSEL3 registers (Register 31-3 through 001111 [15] CCP1 output
Register 31-6).
001110 [14] Timer2 overflow
001101 [13] Timer1 overflow
001100 [12] Timer0 overflow
001011 [11] CLKR
001010 [10] ADCRC
001001 [9] SOSC
001000 [8] MFINTOSC (32 kHz)
000111 [7] MFINTOSC (500 kHz)
000110 [6] LFINTOSC
000101 [5] HFINTOSC
000100 [4] FOSC
000011 [3] CLCIN3PPS
000010 [2] CLCIN2PPS
000001 [1] CLCIN1PPS

 2016-2018 Microchip Technology Inc. DS40001866B-page 402


PIC16(L)F15356/75/76/85/86
31.1.2 DATA GATING Data gating is indicated in the right side of Figure 31-2.
Only one gate is shown in detail. The remaining three
Outputs from the input multiplexers are directed to the
gates are configured identically with the exception that
desired logic function input through the data gating
the data enables correspond to the enables for that
stage. Each data gate can direct any combination of the
gate.
four selected inputs.
Note: Data gating is undefined at power-up. 31.1.3 LOGIC FUNCTION
The gate stage is more than just signal direction. The There are eight available logic functions including:
gate can be configured to direct each input signal as • AND-OR
inverted or non-inverted data. The output of each gate • OR-XOR
can be inverted before going on to the logic function
• AND
stage.
• S-R Latch
The gating is in essence a 1-to-4 input AND/NAND/OR/
• D Flip-Flop with Set and Reset
NOR gate. When every input is inverted and the output
is inverted, the gate is an OR of all enabled data inputs. • D Flip-Flop with Reset
When the inputs and output are not inverted, the gate • J-K Flip-Flop with Reset
is an AND or all enabled inputs. • Transparent Latch with Set and Reset
Table 31-3 summarizes the basic logic that can be Logic functions are shown in Figure 31-2. Each logic
obtained in gate 1 by using the gate logic select bits. function has four inputs and one output. The four inputs
The table shows the logic of four input variables, but are the four data gate outputs of the previous stage.
The output is fed to the inversion stage and from there
each gate can be configured to use less than four. If
to other peripherals, an output pin, and back to the
no inputs are selected, the output will be zero or one,
CLCx itself.
depending on the gate output polarity bit.
31.1.4 OUTPUT POLARITY
TABLE 31-3: DATA GATING LOGIC
The last stage in the Configurable Logic Cell is the
CLCxGLSy LCxGyPOL Gate Logic output polarity. Setting the LCxPOL bit of the CLCxPOL
0x55 1 4-input AND register inverts the output signal from the logic stage.
Changing the polarity while the interrupts are enabled
0x55 0 4-input NAND will cause an interrupt for the resulting output transition.
0xAA 1 4-input NOR
0xAA 0 4-input OR
0x00 0 Logic 0
0x00 1 Logic 1
It is possible (but not recommended) to select both the
true and negated values of an input. When this is done,
the gate output is zero, regardless of the other inputs,
but may emit logic glitches (transient-induced pulses).
If the output of the channel must be zero or one, the
recommended method is to set all gate bits to zero and
use the gate polarity bit to set the desired level.
Data gating is configured with the logic gate select
registers as follows:
• Gate 1: CLCxGLS0 (Register 31-7)
• Gate 2: CLCxGLS1 (Register 31-8)
• Gate 3: CLCxGLS2 (Register 31-9)
• Gate 4: CLCxGLS3 (Register 31-10)
Register number suffixes are different than the gate
numbers because other variations of this module have
multiple gate selections in the same register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 403


PIC16(L)F15356/75/76/85/86
31.2 CLCx Interrupts 31.6 CLCx Setup Steps
An interrupt will be generated upon a change in the The following steps should be followed when setting up
output value of the CLCx when the appropriate interrupt the CLCx:
enables are set. A rising edge detector and a falling • Disable CLCx by clearing the LCxEN bit.
edge detector are present in each CLC for this purpose.
• Select desired inputs using CLCxSEL0 through
The CLCxIF bit of the associated PIR5 register will be CLCxSEL3 registers (See Table 31-2).
set when either edge detector is triggered and its asso- • Clear any associated ANSEL bits.
ciated enable bit is set. The LCxINTP enables rising
• Enable the chosen inputs through the four gates
edge interrupts and the LCxINTN bit enables falling
using CLCxGLS0, CLCxGLS1, CLCxGLS2, and
edge interrupts. Both are located in the CLCxCON
CLCxGLS3 registers.
register.
• Select the gate output polarities with the
To fully enable the interrupt, set the following bits: LCxGyPOL bits of the CLCxPOL register.
• CLCxIE bit of the PIE5 register • Select the desired logic function with the
• LCxINTP bit of the CLCxCON register (for a rising LCxMODE<2:0> bits of the CLCxCON register.
edge detection) • Select the desired polarity of the logic output with
• LCxINTN bit of the CLCxCON register (for a the LCxPOL bit of the CLCxPOL register. (This
falling edge detection) step may be combined with the previous gate out-
• PEIE and GIE bits of the INTCON register put polarity step).
• If driving a device pin, set the desired pin PPS
The CLCxIF bit of the PIR5 register, must be cleared in
control register and also clear the TRIS bit
software as part of the interrupt service. If another edge
corresponding to that output.
is detected while this flag is being cleared, the flag will
still be set at the end of the sequence. • If interrupts are desired, configure the following
bits:
31.3 Output Mirror Copies - Set the LCxINTP bit in the CLCxCON register
for rising event.
Mirror copies of all LCxCON output bits are contained - Set the LCxINTN bit in the CLCxCON
in the CLCxDATA register. Reading this register reads register for falling event.
the outputs of all CLCs simultaneously. This prevents
- Set the CLCxIE bit of the PIE5 register.
any reading skew introduced by testing or reading the
LCxOUT bits in the individual CLCxCON registers. - Set the GIE and PEIE bits of the INTCON
register.
31.4 Effects of a Reset • Enable the CLCx by setting the LCxEN bit of the
CLCxCON register.
The CLCxCON register is cleared to zero as the result
of a Reset. All other selection and gating values remain
unchanged.

31.5 Operation During Sleep


The CLC module operates independently from the
system clock and will continue to run during Sleep,
provided that the input sources selected remain active.
The HFINTOSC remains active during Sleep when the
CLC module is enabled and the HFINTOSC is
selected as an input source, regardless of the system
clock source selected.
In other words, if the HFINTOSC is simultaneously
selected as the system clock and as a CLC input
source, when the CLC is enabled, the CPU will go idle
during Sleep, but the CLC will continue to operate and
the HFINTOSC will remain active.
This will have a direct effect on the Sleep mode current.

 2016-2018 Microchip Technology Inc. DS40001866B-page 404


PIC16(L)F15356/75/76/85/86
FIGURE 31-2: INPUT DATA SELECTION AND GATING

Data Selection
LCx_in
Data GATE 1

lcxd1T LCxD1G1T

lcxd1N LCxD1G1N
LCx_in
LCxD2G1T
LCxD1S<5:0>

LCxD2G1N lcxg1
LCx_in
LCxD3G1T
LCxG1POL
lcxd2T
LCxD3G1N
lcxd2N
LCxD4G1T
LCx_in

LCxD2S<5:0> LCxD4G1N

LCx_in
Data GATE 2
lcxg2
lcxd3T
(Same as Data GATE 1)
lcxd3N
Data GATE 3
LCx_in
lcxg3
LCxD3S<5:0>
(Same as Data GATE 1)

LCx_in Data GATE 4


lcxg4

lcxd4T (Same as Data GATE 1)

lcxd4N

LCx_in

LCxD4S<5:0>

 2016-2018 Microchip Technology Inc. DS40001866B-page 405


PIC16(L)F15356/75/76/85/86
FIGURE 31-3: PROGRAMMABLE LOGIC FUNCTIONS
Rev. 10-000122A
5/18/2016

AND-OR OR-XOR

lcxg1 lcxg1

lcxg2 lcxg2
lcxq lcxq
lcxg3 lcxg3

lcxg4 lcxg4

LCxMODE<2:0> = 000 LCxMODE<2:0> = 001


4-input AND S-R Latch

lcxg1 lcxg1
S Q lcxq
lcxg2
lcxg2
lcxq
lcxg3
lcxg3
R
lcxg4 lcxg4

LCxMODE<2:0> = 010 LCxMODE<2:0> = 011


1-Input D Flip-Flop with S and R 2-Input D Flip-Flop with R
lcxg4
S
lcxg4
lcxg2 D Q lcxq D Q lcxq
lcxg2

lcxg1 R
lcxg1 R
lcxg3 lcxg3

LCxMODE<2:0> = 100 LCxMODE<2:0> = 101


J-K Flip-Flop with R 1-Input Transparent Latch with S and R
lcxg4
lcxg2 J Q lcxq S
lcxg2 D Q lcxq
lcxg1
lcxg4 K
R
lcxg3 LE
R
lcxg3
lcxg1

LCxMODE<2:0> = 110 LCxMODE<2:0> = 111

 2016-2018 Microchip Technology Inc. DS40001866B-page 406


PIC16(L)F15356/75/76/85/86
31.7 Register Definitions: CLC Control

REGISTER 31-1: CLCxCON: CONFIGURABLE LOGIC CELL CONTROL REGISTER


R/W-0/0 U-0 R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
LCxEN — LCxOUT LCxINTP LCxINTN LCxMODE<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxEN: Configurable Logic Cell Enable bit


1 = Configurable logic cell is enabled and mixing input signals
0 = Configurable logic cell is disabled and has logic zero output
bit 6 Unimplemented: Read as ‘0’
bit 5 LCxOUT: Configurable Logic Cell Data Output bit
Read-only: logic cell output data, after LCPOL; sampled from CLCxOUT
bit 4 LCxINTP: Configurable Logic Cell Positive Edge Going Interrupt Enable bit
1 = CLCxIF will be set when a rising edge occurs on CLCxOUT
0 = CLCxIF will not be set
bit 3 LCxINTN: Configurable Logic Cell Negative Edge Going Interrupt Enable bit
1 = CLCxIF will be set when a falling edge occurs on CLCxOUT
0 = CLCxIF will not be set
bit 2-0 LCxMODE<2:0>: Configurable Logic Cell Functional Mode bits
111 =Cell is 1-input transparent latch with S and R
110 =Cell is J-K flip-flop with R
101 =Cell is 2-input D flip-flop with R
100 =Cell is 1-input D flip-flop with S and R
011 =Cell is S-R latch
010 =Cell is 4-input AND
001 =Cell is OR-XOR
000 =Cell is AND-OR

 2016-2018 Microchip Technology Inc. DS40001866B-page 407


PIC16(L)F15356/75/76/85/86

REGISTER 31-2: CLCxPOL: SIGNAL POLARITY CONTROL REGISTER


R/W-0/0 U-0 U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LCxPOL — — — LCxG4POL LCxG3POL LCxG2POL LCxG1POL
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxPOL: CLCxOUT Output Polarity Control bit


1 = The output of the logic cell is inverted
0 = The output of the logic cell is not inverted
bit 6-4 Unimplemented: Read as ‘0’
bit 3 LCxG4POL: Gate 3 Output Polarity Control bit
1 = The output of gate 3 is inverted when applied to the logic cell
0 = The output of gate 3 is not inverted
bit 2 LCxG3POL: Gate 2 Output Polarity Control bit
1 = The output of gate 2 is inverted when applied to the logic cell
0 = The output of gate 2 is not inverted
bit 1 LCxG2POL: Gate 1 Output Polarity Control bit
1 = The output of gate 1 is inverted when applied to the logic cell
0 = The output of gate 1 is not inverted
bit 0 LCxG1POL: Gate 0 Output Polarity Control bit
1 = The output of gate 0 is inverted when applied to the logic cell
0 = The output of gate 0 is not inverted

 2016-2018 Microchip Technology Inc. DS40001866B-page 408


PIC16(L)F15356/75/76/85/86

REGISTER 31-3: CLCxSEL0: GENERIC CLCx DATA 0 SELECT REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — LCxD1S<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 LCxD1S<5:0>: CLCx Data1 Input Selection bits
See Table 31-2.

REGISTER 31-4: CLCxSEL1: GENERIC CLCx DATA 1 SELECT REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — LCxD2S<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 LCxD2S<5:0>: CLCx Data 2 Input Selection bits
See Table 31-2.

REGISTER 31-5: CLCxSEL2: GENERIC CLCx DATA 2 SELECT REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — LCxD3S<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 LCxD3S<5:0>: CLCx Data 3 Input Selection bits
See Table 31-2.

REGISTER 31-6: CLCxSEL3: GENERIC CLCx DATA 3 SELECT REGISTER


U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
— — LCxD4S<5:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-6 Unimplemented: Read as ‘0’


bit 5-0 LCxD4S<5:0>: CLCx Data 4 Input Selection bits
See Table 31-2.

 2016-2018 Microchip Technology Inc. DS40001866B-page 409


PIC16(L)F15356/75/76/85/86

REGISTER 31-7: CLCxGLS0: GATE 0 LOGIC SELECT REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LCxG1D4T LCxG1D4N LCxG1D3T LCxG1D3N LCxG1D2T LCxG1D2N LCxG1D1T LCxG1D1N
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxG1D4T: Gate 0 Data 4 True (non-inverted) bit


1 = CLCIN3 (true) is gated into CLCx Gate 0
0 = CLCIN3 (true) is not gated into CLCx Gate 0
bit 6 LCxG1D4N: Gate 0 Data 4 Negated (inverted) bit
1 = CLCIN3 (inverted) is gated into CLCx Gate 0
0 = CLCIN3 (inverted) is not gated into CLCx Gate 0
bit 5 LCxG1D3T: Gate 0 Data 3 True (non-inverted) bit
1 = CLCIN2 (true) is gated into CLCx Gate 0
0 = CLCIN2 (true) is not gated into CLCx Gate 0
bit 4 LCxG1D3N: Gate 0 Data 3 Negated (inverted) bit
1 = CLCIN2 (inverted) is gated into CLCx Gate 0
0 = CLCIN2 (inverted) is not gated into CLCx Gate 0
bit 3 LCxG1D2T: Gate 0 Data 2 True (non-inverted) bit
1 = CLCIN1 (true) is gated into CLCx Gate 0
0 = CLCIN1 (true) is not gated into l CLCx Gate 0
bit 2 LCxG1D2N: Gate 0 Data 2 Negated (inverted) bit
1 = CLCIN1 (inverted) is gated into CLCx Gate 0
0 = CLCIN1 (inverted) is not gated into CLCx Gate 0
bit 1 LCxG1D1T: Gate 0 Data 1 True (non-inverted) bit
1 = CLCIN0 (true) is gated into CLCx Gate 0
0 = CLCIN0 (true) is not gated into CLCx Gate 0
bit 0 LCxG1D1N: Gate 0 Data 1 Negated (inverted) bit
1 = CLCIN0 (inverted) is gated into CLCx Gate 0
0 = CLCIN0 (inverted) is not gated into CLCx Gate 0

 2016-2018 Microchip Technology Inc. DS40001866B-page 410


PIC16(L)F15356/75/76/85/86

REGISTER 31-8: CLCxGLS1: GATE 1 LOGIC SELECT REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LCxG2D4T LCxG2D4N LCxG2D3T LCxG2D3N LCxG2D2T LCxG2D2N LCxG2D1T LCxG2D1N
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxG2D4T: Gate 1 Data 4 True (non-inverted) bit


1 = CLCIN3 (true) is gated into CLCx Gate 1
0 = CLCIN3 (true) is not gated into CLCx Gate 1
bit 6 LCxG2D4N: Gate 1 Data 4 Negated (inverted) bit
1 = CLCIN3 (inverted) is gated into CLCx Gate 1
0 = CLCIN3 (inverted) is not gated into CLCx Gate 1
bit 5 LCxG2D3T: Gate 1 Data 3 True (non-inverted) bit
1 = CLCIN2 (true) is gated into CLCx Gate 1
0 = CLCIN2 (true) is not gated into CLCx Gate 1
bit 4 LCxG2D3N: Gate 1 Data 3 Negated (inverted) bit
1 = CLCIN2 (inverted) is gated into CLCx Gate 1
0 = CLCIN2 (inverted) is not gated into CLCx Gate 1
bit 3 LCxG2D2T: Gate 1 Data 2 True (non-inverted) bit
1 = CLCIN1 (true) is gated into CLCx Gate 1
0 = CLCIN1 (true) is not gated into CLCx Gate 1
bit 2 LCxG2D2N: Gate 1 Data 2 Negated (inverted) bit
1 = CLCIN1 (inverted) is gated into CLCx Gate 1
0 = CLCIN1 (inverted) is not gated into CLCx Gate 1
bit 1 LCxG2D1T: Gate 1 Data 1 True (non-inverted) bit
1 = CLCIN0 (true) is gated into CLCx Gate 1
0 = CLCIN0 (true) is not gated into CLCx Gate1
bit 0 LCxG2D1N: Gate 1 Data 1 Negated (inverted) bit
1 = CLCIN0 (inverted) is gated into CLCx Gate 1
0 = CLCIN0 (inverted) is not gated into CLCx Gate 1

 2016-2018 Microchip Technology Inc. DS40001866B-page 411


PIC16(L)F15356/75/76/85/86

REGISTER 31-9: CLCxGLS2: GATE 2 LOGIC SELECT REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LCxG3D4T LCxG3D4N LCxG3D3T LCxG3D3N LCxG3D2T LCxG3D2N LCxG3D1T LCxG3D1N
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxG3D4T: Gate 2 Data 4 True (non-inverted) bit


1 = CLCIN3 (true) is gated into CLCx Gate 2
0 = CLCIN3 (true) is not gated into CLCx Gate 2
bit 6 LCxG3D4N: Gate 2 Data 4 Negated (inverted) bit
1 = CLCIN3 (inverted) is gated into CLCx Gate 2
0 = CLCIN3 (inverted) is not gated into CLCx Gate 2
bit 5 LCxG3D3T: Gate 2 Data 3 True (non-inverted) bit
1 = CLCIN2 (true) is gated into CLCx Gate 2
0 = CLCIN2 (true) is not gated into CLCx Gate 2
bit 4 LCxG3D3N: Gate 2 Data 3 Negated (inverted) bit
1 = CLCIN2 (inverted) is gated into CLCx Gate 2
0 = CLCIN2 (inverted) is not gated into CLCx Gate 2
bit 3 LCxG3D2T: Gate 2 Data 2 True (non-inverted) bit
1 = CLCIN1 (true) is gated into CLCx Gate 2
0 = CLCIN1 (true) is not gated into CLCx Gate 2
bit 2 LCxG3D2N: Gate 2 Data 2 Negated (inverted) bit
1 = CLCIN1 (inverted) is gated into CLCx Gate 2
0 = CLCIN1 (inverted) is not gated into CLCx Gate 2
bit 1 LCxG3D1T: Gate 2 Data 1 True (non-inverted) bit
1 = CLCIN0 (true) is gated into CLCx Gate 2
0 = CLCIN0 (true) is not gated into CLCx Gate 2
bit 0 LCxG3D1N: Gate 2 Data 1 Negated (inverted) bit
1 = CLCIN0 (inverted) is gated into CLCx Gate 2
0 = CLCIN0 (inverted) is not gated into CLCx Gate 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 412


PIC16(L)F15356/75/76/85/86

REGISTER 31-10: CLCxGLS3: GATE 3 LOGIC SELECT REGISTER


R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LCxG4D4T LCxG4D4N LCxG4D3T LCxG4D3N LCxG4D2T LCxG4D2N LCxG4D1T LCxG4D1N
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 LCxG4D4T: Gate 3 Data 4 True (non-inverted) bit


1 = CLCIN3 (true) is gated into CLCx Gate 3
0 = CLCIN3 (true) is not gated into CLCx Gate 3
bit 6 LCxG4D4N: Gate 3 Data 4 Negated (inverted) bit
1 = CLCIN3 (inverted) is gated into CLCx Gate 3
0 = CLCIN3 (inverted) is not gated into CLCx Gate 3
bit 5 LCxG4D3T: Gate 3 Data 3 True (non-inverted) bit
1 = CLCIN2 (true) is gated into CLCx Gate 3
0 = CLCIN2 (true) is not gated into CLCx Gate 3
bit 4 LCxG4D3N: Gate 3 Data 3 Negated (inverted) bit
1 = CLCIN2 (inverted) is gated into CLCx Gate 3
0 = CLCIN2 (inverted) is not gated into CLCx Gate 3
bit 3 LCxG4D2T: Gate 3 Data 2 True (non-inverted) bit
1 = CLCIN1 (true) is gated into CLCx Gate 3
0 = CLCIN1 (true) is not gated into CLCx Gate 3
bit 2 LCxG4D2N: Gate 3 Data 2 Negated (inverted) bit
1 = CLCIN1 (inverted) is gated into CLCx Gate 3
0 = CLCIN1 (inverted) is not gated into CLCx Gate 3
bit 1 LCxG4D1T: Gate 4 Data 1 True (non-inverted) bit
1 = CLCIN0 (true) is gated into CLCx Gate 3
0 = CLCIN0 (true) is not gated into CLCx Gate 3
bit 0 LCxG4D1N: Gate 3 Data 1 Negated (inverted) bit
1 = CLCIN0 (inverted) is gated into CLCx Gate 3
0 = CLCIN0 (inverted) is not gated into CLCx Gate 3

 2016-2018 Microchip Technology Inc. DS40001866B-page 413


PIC16(L)F15356/75/76/85/86

REGISTER 31-11: CLCDATA: CLC DATA OUTPUT


U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0
— — — — MLC4OUT MLC3OUT MLC2OUT MLC1OUT
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3 MLC4OUT: Mirror copy of LC4OUT bit
bit 2 MLC3OUT: Mirror copy of LC3OUT bit
bit 1 MLC2OUT: Mirror copy of LC2OUT bit
bit 0 MLC1OUT: Mirror copy of LC1OUT bit

 2016-2018 Microchip Technology Inc. DS40001866B-page 414


PIC16(L)F15356/75/76/85/86

TABLE 31-4: SUMMARY OF REGISTERS ASSOCIATED WITH CLCx

Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE ― ― ― ― ― INTEDG 147

PIR5 CLC4IF CLC3IF CLC2IF CLC1IF — — — TMR1GIF 161

PIE5 CLC4IE CLC4IE CLC2IE CLC1IE — — — TMR1GIE 153

CLC1CON LC1EN ― LC1OUT LC1INTP LC1INTN LC1MODE<2:0> 407

CLC1POL LC1POL ― ― ― LC1G4POL LC1G3POL LC1G2POL LC1G1POL 408

CLC1SEL0 ― ― LC1D1S<5:0> 409

CLC1SEL1 ― ― LC1D2S<5:0> 409

CLC1SEL2 ― ― LC1D3S<5:0> 409

CLC1SEL3 ― ― LC1D4S<5:0> 409

CLC1GLS0 ― ― LC1G1D3T LC1G1D3N LC1G1D2T LC1G1D2N LC1G1D1T LC1G1D1N 410

CLC1GLS1 ― ― LC1G2D3T LC1G2D3N LC1G2D2T LC1G2D2N LC1G2D1T LC1G2D1N 411

CLC1GLS2 ― ― LC1G3D3T LC1G3D3N LC1G3D2T LC1G3D2N LC1G3D1T LC1G3D1N 412

CLC1GLS3 ― ― LC1G4D3T LC1G4D3N LC1G4D2T LC1G4D2N LC1G4D1T LC1G4D1N 413

CLC2CON LC2EN ― LC2OUT LC2INTP LC2INTN LC2MODE<2:0> 407

CLC2POL LC2POL ― ― ― LC2G4POL LC2G3POL LC2G2POL LC2G1POL 408

CLC2SEL0 ― ― LC2D1S<5:0> 409

CLC2SEL1 ― ― LC2D2S<5:0> 409

CLC2SEL2 ― ― LC2D3S<5:0> 409

CLC2SEL3 ― ― LC2D4S<5:0> 409

CLC2GLS0 ― ― LC2G1D3T LC2G1D3N LC2G1D2T LC2G1D2N LC2G1D1T LC2G1D1N 410

CLC2GLS1 ― ― LC2G2D3T LC2G2D3N LC2G2D2T LC2G2D2N LC2G2D1T LC2G2D1N 411

CLC2GLS2 ― ― LC2G3D3T LC2G3D3N LC2G3D2T LC2G3D2N LC2G3D1T LC2G3D1N 412

CLC2GLS3 ― ― LC2G4D3T LC2G4D3N LC2G4D2T LC2G4D2N LC2G4D1T LC2G4D1N 413

CLC3CON LC3EN ― LC3OUT LC3INTP LC3INTN LC3MODE<2:0> 407

CLC3POL LC3POL ― ― ― LC3G4POL LC3G3POL LC3G2POL LC3G1POL 408

CLC3SEL0 ― ― LC3D1S<5:0> 409

CLC3SEL1 ― ― LC3D2S<5:0> 409

CLC3SEL2 ― ― LC3D3S<5:0> 409

CLC3SEL3 ― ― LC3D4S<5:0> 409

CLC3GLS0 ― ― LC3G1D3T LC3G1D3N LC3G1D2T LC3G1D2N LC3G1D1T LC3G1D1N 410

CLC3GLS1 ― ― LC3G2D3T LC3G2D3N LC3G2D2T LC3G2D2N LC3G2D1T LC3G2D1N 411

CLC3GLS2 ― ― LC3G3D3T LC3G3D3N LC3G3D2T LC3G3D2N LC3G3D1T LC3G3D1N 412

CLC3GLS3 ― ― LC3G4D3T LC3G4D3N LC3G4D2T LC3G4D2N LC3G4D1T LC3G4D1N 413

CLC4CON LC4EN ― LC4OUT LC4INTP LC4INTN LC4MODE<2:0> 407

CLC4POL LC4POL ― ― ― LC4G4POL LC4G3POL LC4G2POL LC4G1POL 408

CLC4SEL0 ― ― LC4D1S<5:0> 409

CLC4SEL1 ― ― LC4D2S<5:0> 409

CLC4SEL2 ― ― LC4D3S<5:0> 409

CLC4SEL3 ― ― LC4D4S<5:0> 409

CLC4GLS0 ― ― LC4G1D3T LC4G1D3N LC4G1D2T LC4G1D2N LC4G1D1T LC4G1D1N 410


Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the CLCx modules.

 2016-2018 Microchip Technology Inc. DS40001866B-page 415


PIC16(L)F15356/75/76/85/86
TABLE 31-4: SUMMARY OF REGISTERS ASSOCIATED WITH CLCx (continued)

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

CLC4GLS1 ― ― LC4G2D3T LC4G2D3N LC4G2D2T LC4G2D2N LC4G2D1T LC4G2D1N 411

CLC4GLS2 ― ― LC4G3D3T LC4G3D3N LC4G3D2T LC4G3D2N LC4G3D1T LC4G3D1N 412

CLC4GLS3 ― ― LC4G4D3T LC4G4D3N LC4G4D2T LC4G4D2N LC4G4D1T LC4G4D1N 413

CLCIN0PPS ― ― CLCIN0PPS<5:0> 242

CLCIN1PPS ― ― CLCIN1PPS<5:0> 242

CLCIN2PPS ― ― CLCIN2PPS<5:0> 242

CLCIN3PPS ― ― CLCIN3PPS<5:0> 242


Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the CLCx modules.

 2016-2018 Microchip Technology Inc. DS40001866B-page 416


PIC16(L)F15356/75/76/85/86
32.0 MASTER SYNCHRONOUS
SERIAL PORT (MSSPx)
MODULES
32.1 MSSP Module Overview
The Master Synchronous Serial Port (MSSP) module is
a serial interface useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers,
display drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C)
The SPI interface supports the following modes and
features:
• Master mode
• Slave mode
• Clock Parity
• Slave Select Synchronization (Slave mode only)
• Daisy-chain connection of slave devices
Figure 32-1 is a block diagram of the SPI interface
module.

FIGURE 32-1: MSSP BLOCK DIAGRAM (SPI MODE)

Data Bus
Read Write

SSPxBUF Reg

SSPDATPPS
SDI
PPS SSPSR Reg
SDO bit 0 Shift
Clock
PPS

RxyPPS

SS SS Control 2 (CKP, CKE)


PPS Enable Clock Select

Edge
SSPSSPPS Select

SSPCLKPPS(2) SSPM<3:0>

SCK PPS
4
( T2_match
2
)
Edge Prescaler TOSC
PPS Select 4, 16, 64

TRIS bit RxyPPS(1) Baud Rate


Generator
(SSPxADD)
Note 1: Output selection for master mode
2: Input selection for slave mode

 2016-2018 Microchip Technology Inc. DS40001866B-page 417


PIC16(L)F15356/75/76/85/86
The I2C interface supports the following modes and
features:
Note 1: In devices with more than one MSSP
• Master mode module, it is very important to pay close
• Slave mode attention to SSPxCONx register names.
• Byte NACKing (Slave mode) SSPxCON1 and SSPxCON2 registers
• Limited multi-master support control different operational aspects of
the same module, while SSP1CON1 and
• 7-bit and 10-bit addressing
SSP2CON1 control the same features for
• Start and Stop interrupts two different modules.
• Interrupt masking
2: Throughout this section, generic refer-
• Clock stretching ences to an MSSPx module in any of its
• Bus collision detection operating modes may be interpreted as
• General call address matching being equally applicable to MSSP1 or
• Address masking MSSP2. Register names, module I/O sig-
nals, and bit names may use the generic
• Selectable SDA hold times
designator ‘x’ to indicate the use of a
Figure 32-2 is a block diagram of the I2C interface numeral to distinguish a particular module
module in Master mode. Figure 32-3 is a diagram of the when required.
I2C interface module in Slave mode.

FIGURE 32-2: MSSP BLOCK DIAGRAM (I2C MASTER MODE)

Internal
data bus [SSPM<3:0>]
SSPDATPPS(1) Read Write
SDA
SDA in
PPS SSPxBUF Baud Rate
Generator
(SSPxADD)
Shift
RxyPPS(1) Clock

Clock arbitrate/BCOL detect


SSPSR
Clock Cntl

(Hold off clock source)


PPS MSb LSb
Receive Enable (RCEN)

Start bit, Stop bit,


Acknowledge
(2)
SSPCLKPPS Generate (SSPxCON2)
SCL
PPS

PPS

Start bit detect,


RxyPPS(2) Stop bit detect
Write collision detect Set/Reset: S, P, SSPxSTAT, WCOL, SSPOV
SCL in
Clock arbitration Reset SEN, PEN (SSPxCON2)
State counter for Set SSPxIF, BCL1IF
Bus Collision end of XMIT/RCV
Address Match detect

Note 1: SDA pin selections must be the same for input and output
2: SCL pin selections must be the same for input and output

 2016-2018 Microchip Technology Inc. DS40001866B-page 418


PIC16(L)F15356/75/76/85/86
FIGURE 32-3: MSSP BLOCK DIAGRAM (I2C SLAVE MODE)

Internal
Data Bus

Read Write

SSPCLKPPS(2) SSPxBUF Reg


SCL
PPS
Shift
Clock
Clock
PPS Stretching SSPSR Reg
MSb LSb
RxyPPS(2)

SSPxMSK Reg

SSPDATPPS(1)
SDA Match Detect Addr Match
PPS
SSPxADD Reg
PPS
Start and Set, Reset
RxyPPS(1) Stop bit Detect S, P bits
(SSPxSTAT Reg)

Note 1: SDA pin selections must be the same for input and output
2: SCL pin selections must be the same for input and output

 2016-2018 Microchip Technology Inc. DS40001866B-page 419


PIC16(L)F15356/75/76/85/86
32.2 SPI Mode Overview During each SPI clock cycle, a full-duplex data
transmission occurs. This means that while the master
The Serial Peripheral Interface (SPI) bus is a device is sending out the MSb from its shift register (on
synchronous serial data communication bus that its SDO pin) and the slave device is reading this bit and
operates in Full-Duplex mode. Devices communicate saving it as the LSb of its shift register, that the slave
in a master/slave environment where the master device device is also sending out the MSb from its shift register
initiates the communication. A slave device is (on its SDO pin) and the master device is reading this
controlled through a Chip Select known as Slave bit and saving it as the LSb of its shift register.
Select.
After eight bits have been shifted out, the master and
The SPI bus specifies four signal connections: slave have exchanged register values.
• Serial Clock (SCK) If there is more data to exchange, the shift registers are
• Serial Data Out (SDO) loaded with new data and the process repeats itself.
• Serial Data In (SDI) Whether the data is meaningful or not (dummy data),
• Slave Select (SS) depends on the application software. This leads to
Figure 32-1 shows the block diagram of the MSSP three scenarios for data transmission:
module when operating in SPI mode. • Master sends useful data and slave sends dummy
The SPI bus operates with a single master device and data.
one or more slave devices. When multiple slave • Master sends useful data and slave sends useful
devices are used, an independent Slave Select data.
connection can be used to address each slave individ- • Master sends dummy data and slave sends useful
ually. data.
Figure 32-4 shows a typical connection between a Transmissions must be performed in multiples of eight
master device and multiple slave devices. clock pulses. When there is no more data to be trans-
The master selects only one slave at a time. Most slave mitted, the master stops sending the clock signal and it
devices have tri-state outputs so their output signal deselects the slave.
appears disconnected from the bus when they are not Every slave device connected to the bus that has not
selected. been selected through its slave select line must disre-
Transmissions involve two shift registers, eight bits in gard the clock and transmission signals and must not
size, one in the master and one in the slave. Data is transmit out any data of its own.
always shifted out one bit at a time, with the Most
Significant bit (MSb) shifted out first. At the same time,
a new Least Significant bit (LSb) is shifted into the
same register.
Figure 32-5 shows a typical connection between two
processors configured as master and slave devices.
Data is shifted out of both shift registers on the
programmed clock edge and latched on the opposite
edge of the clock.
The master device transmits information out on its SDO
output pin which is connected to, and received by, the
slave’s SDI input pin. The slave device transmits infor-
mation out on its SDO output pin, which is connected
to, and received by, the master’s SDI input pin.
To begin communication, the master device first sends
out the clock signal. Both the master and the slave
devices should be configured for the same clock polar-
ity.
The master device starts a transmission by sending out
the MSb from its shift register. The slave device reads
this bit from that same line and saves it into the LSb
position of its shift register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 420


PIC16(L)F15356/75/76/85/86
FIGURE 32-4: SPI MASTER AND MULTIPLE SLAVE CONNECTION

SCK SCK
SPI Master
SDO SDI SPI Slave
SDI SDO #1
General I/O SS
General I/O
General I/O SCK
SDI SPI Slave
SDO #2
SS

SCK
SDI SPI Slave
SDO #3
SS

32.2.1 SPI MODE REGISTERS


The MSSP module has five registers for SPI mode
operation. These are:
• MSSP STATUS register (SSPxSTAT)
• MSSP Control register 1 (SSPxCON1)
• MSSP Control register 3 (SSPxCON3)
• MSSP Data Buffer register (SSPxBUF)
• MSSP Address register (SSPxADD)
• MSSP Shift register (SSPxSR)
(Not directly accessible)
SSPxCON1 and SSPxSTAT are the control and status
registers in SPI mode operation. The SSPxCON1
register is readable and writable. The lower six bits of
the SSPxSTAT are read-only. The upper two bits of the
SSPxSTAT are read/write.
In one SPI master mode, SSPxADD can be loaded
with a value used in the Baud Rate Generator. More
information on the Baud Rate Generator is available in
Section 32.7 “Baud Rate Generator”.
SSPxSR is the shift register used for shifting data in
and out. SSPxBUF provides indirect access to the
SSPxSR register. SSPxBUF is the buffer register to
which data bytes are written, and from which data
bytes are read.
In receive operations, SSPxSR and SSPxBUF
together create a buffered receiver. When SSPxSR
receives a complete byte, it is transferred to SSPxBUF
and the SSPxIF interrupt is set.
During transmission, the SSPxBUF is not buffered. A
write to SSPxBUF will write to both SSPxBUF and
SSPxSR.

 2016-2018 Microchip Technology Inc. DS40001866B-page 421


PIC16(L)F15356/75/76/85/86
32.2.2 SPI MODE OPERATION The MSSP consists of a transmit/receive shift register
(SSPxSR) and a buffer register (SSPxBUF). The
When initializing the SPI, several options need to be SSPxSR shifts the data in and out of the device, MSb first.
specified. This is done by programming the appropriate The SSPxBUF holds the data that was written to the
control bits (SSPxCON1<3:0> and SSPxSTAT<7:6>). SSPxSR until the received data is ready. Once the eight
These control bits allow the following to be specified: bits of data have been received, that byte is moved to the
• Master mode (SCK is the clock output) SSPxBUF register. Then, the Buffer Full Detect bit, BF of
• Slave mode (SCK is the clock input) the SSPxSTAT register, and the interrupt flag bit, SSPxIF,
• Clock Polarity (Idle state of SCK) are set. Any write to the SSPxBUF register during
transmission/reception of data will be ignored and the
• Data Input Sample Phase (middle or end of data
write collision detect bit WCOL of the SSPxCON1
output time)
register, will be set. User software must clear the WCOL
• Clock Edge (output data on rising/falling edge of bit to allow the following write(s) to the SSPxBUF register
SCK) to complete successfully.
• Clock Rate (Master mode only)
When the application software is expecting to receive
• Slave Select mode (Slave mode only) valid data, the SSPxBUF should be read before the next
To enable the serial port, SSP Enable bit, SSPEN of the byte of data to transfer is written to the SSPxBUF. The
SSPxCON1 register, must be set. To reset or reconfig- Buffer Full bit, BF of the SSPxSTAT register, indicates
ure SPI mode, clear the SSPEN bit, re-initialize the when SSPxBUF has been loaded with the received data
SSPxCONx registers and then set the SSPEN bit. This (transmission is complete). When the SSPxBUF is read,
configures the SDI, SDO, SCK and SS pins as serial port the BF bit is cleared. This data may be irrelevant if the
pins. For the pins to behave as the serial port function, SPI is only a transmitter. Generally, the MSSP interrupt
some must have their data direction bits (in the TRISx is used to determine when the transmission/reception
register) appropriately programmed as follows: has completed. If the interrupt method is not going to be
used, then software polling can be done to ensure that a
• SDI must have corresponding TRIS bit set
write collision does not occur.
• SDO must have corresponding TRIS bit cleared
The SSPxSR is not directly readable or writable and
• SCK (Master mode) must have corresponding
can only be accessed by addressing the SSPxBUF
TRIS bit cleared
register.
• SCK (Slave mode) must have corresponding
TRIS bit set
• SS must have corresponding TRIS bit set
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.

FIGURE 32-5: SPI MASTER/SLAVE CONNECTION

SPI Master SSPM<3:0> = 00xx SPI Slave SSPM<3:0> = 010x


= 1010
SDO SDI

Serial Input Buffer Serial Input Buffer


(SSPxBUF) (SSPxBUF)

Shift Register SDI SDO Shift Register


(SSPxSR) (SSPxSR)
MSb LSb MSb LSb
Serial Clock
SCK SCK

Slave Select
General I/O SS
Processor 1 (optional) Processor 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 422


PIC16(L)F15356/75/76/85/86
32.2.3 SPI MASTER MODE The clock polarity is selected by appropriately
programming the CKP bit of the SSPxCON1 register
The master can initiate the data transfer at any time
and the CKE bit of the SSPxSTAT register. This then,
because it controls the SCK line. The master
would give waveforms for SPI communication as
determines when the slave (Processor 2, Figure 32-5)
shown in Figure 32-6, Figure 32-8, Figure 32-9 and
is to broadcast data by the software protocol.
Figure 32-10, where the MSB is transmitted first. In
In Master mode, the data is transmitted/received as Master mode, the SPI clock rate (bit rate) is user
soon as the SSPxBUF register is written to. If the SPI programmable to be one of the following:
is only going to receive, the SDO output could be
• FOSC/4 (or TCY)
disabled (programmed as an input). The SSPxSR
register will continue to shift in the signal present on the • FOSC/16 (or 4 * TCY)
SDI pin at the programmed clock rate. As each byte is • FOSC/64 (or 16 * TCY)
received, it will be loaded into the SSPxBUF register as • Timer2 output/2
if a normal received byte (interrupts and Status bits • FOSC/(4 * (SSPxADD + 1))
appropriately set).
Figure 32-6 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPxBUF is loaded with the received
data is shown.

FIGURE 32-6: SPI MODE WAVEFORM (MASTER MODE)

Write to
SSPxBUF

SCK
(CKP = 0
CKE = 0)

SCK
(CKP = 1
CKE = 0)
4 Clock
SCK Modes
(CKP = 0
CKE = 1)

SCK
(CKP = 1
CKE = 1)

SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0


(CKE = 0)

SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0


(CKE = 1)
SDI
(SMP = 0) bit 7 bit 0
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
bit 7 bit 0

Input
Sample
(SMP = 1)
SSPxIF

SSPxSR to
SSPxBUF

 2016-2018 Microchip Technology Inc. DS40001866B-page 423


PIC16(L)F15356/75/76/85/86
32.2.4 SPI SLAVE MODE 32.2.5 SLAVE SELECT
In Slave mode, the data is transmitted and received as SYNCHRONIZATION
external clock pulses appear on SCK. When the last The Slave Select can also be used to synchronize
bit is latched, the SSPxIF interrupt flag bit is set. communication. The Slave Select line is held high until
Before enabling the module in SPI Slave mode, the clock the master device is ready to communicate. When the
line must match the proper Idle state. The clock line can Slave Select line is pulled low, the slave knows that a
be observed by reading the SCK pin. The Idle state is new transmission is starting.
determined by the CKP bit of the SSPxCON1 register. If the slave fails to receive the communication properly,
While in Slave mode, the external clock is supplied by it will be reset at the end of the transmission, when the
the external clock source on the SCK pin. This external Slave Select line returns to a high state. The slave is
clock must meet the minimum high and low times as then ready to receive a new transmission when the
specified in the electrical specifications. Slave Select line is pulled low again. If the Slave Select
line is not used, there is a risk that the slave will
While in Sleep mode, the slave can transmit/receive
eventually become out of sync with the master. If the
data. The shift register is clocked from the SCK pin
slave misses a bit, it will always be one bit off in future
input and when a byte is received, the device will
transmissions. Use of the Slave Select line allows the
generate an interrupt. If enabled, the device will wake-
slave and master to align themselves at the beginning
up from Sleep.
of each transmission.
32.2.4.1 Daisy-Chain Configuration The SS pin allows a Synchronous Slave mode. The
SPI must be in Slave mode with SS pin control enabled
The SPI bus can sometimes be connected in a daisy-
(SSPxCON1<3:0> = 0100).
chain configuration. The first slave output is connected
to the second slave input, the second slave output is When the SS pin is low, transmission and reception are
connected to the third slave input, and so on. The final enabled and the SDO pin is driven.
slave output is connected to the master input. Each When the SS pin goes high, the SDO pin is no longer
slave sends out, during a second group of clock driven, even if in the middle of a transmitted byte and
pulses, an exact copy of what was received during the becomes a floating output. External pull-up/pull-down
first group of clock pulses. The whole chain acts as resistors may be desirable depending on the applica-
one large communication shift register. The daisy- tion.
chain feature only requires a single Slave Select line
from the master device. Note 1: When the SPI is in Slave mode with SS pin
control enabled (SSPxCON1<3:0> =
Figure 32-7 shows the block diagram of a typical
0100), the SPI module will reset if the SS
daisy-chain connection when operating in SPI mode.
pin is set to VDD.
In a daisy-chain configuration, only the most recent
2: When the SPI is used in Slave mode with
byte on the bus is required by the slave. Setting the
CKE set; the user must enable SS pin
BOEN bit of the SSPxCON3 register will enable writes
control.
to the SSPxBUF register, even if the previous byte has
not been read. This allows the software to ignore data 3: While operated in SPI Slave mode the
that may not apply to it. SMP bit of the SSPxSTAT register must
remain clear.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SS pin to
a high level or clearing the SSPEN bit.

 2016-2018 Microchip Technology Inc. DS40001866B-page 424


PIC16(L)F15356/75/76/85/86
FIGURE 32-7: SPI DAISY-CHAIN CONNECTION

SCK SCK
SPI Master
SDO SDI SPI Slave
SDI SDO #1
General I/O SS

SCK
SDI SPI Slave
SDO #2
SS

SCK
SDI SPI Slave
SDO #3
SS

FIGURE 32-8: SLAVE SELECT SYNCHRONOUS WAVEFORM

SS

SCK
(CKP = 0
CKE = 0)

SCK
(CKP = 1
CKE = 0)

Write to
SSPxBUF
Shift register SSPxSR
and bit count are reset
SSPxBUF to
SSPxSR

SDO bit 7 bit 6 bit 7 bit 6 bit 0

SDI bit 0
bit 7 bit 7
Input
Sample

SSPxIF
Interrupt
Flag

SSPxSR to
SSPxBUF

 2016-2018 Microchip Technology Inc. DS40001866B-page 425


PIC16(L)F15356/75/76/85/86
FIGURE 32-9: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0)

SS
Optional

SCK
(CKP = 0
CKE = 0)

SCK
(CKP = 1
CKE = 0)
Write to
SSPxBUF
Valid
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

SDI
bit 7 bit 0
Input
Sample

SSPxIF
Interrupt
Flag
SSPxSR to
SSPxBUF

Write Collision
detection active

FIGURE 32-10: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1)

SS
Not Optional

SCK
(CKP = 0
CKE = 1)

SCK
(CKP = 1
CKE = 1)
Write to
SSPxBUF
Valid
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

SDI
bit 7 bit 0
Input
Sample

SSPxIF
Interrupt
Flag

SSPxSR to
SSPxBUF

Write Collision
detection active

 2016-2018 Microchip Technology Inc. DS40001866B-page 426


PIC16(L)F15356/75/76/85/86
32.2.6 SPI OPERATION IN SLEEP MODE If the requested slave exists on the bus, it will respond
with an Acknowledge bit, otherwise known as an ACK.
In SPI Master mode, module clocks may be operating The master then continues to either transmit or receive
at a different speed than when in Full-Power mode; in data from the slave device.
the case of the Sleep mode, all clocks are halted.
In SPI Master mode, when the Sleep mode is selected, FIGURE 32-11: I2C MASTER/
all module clocks are halted and the transmission/ SLAVE CONNECTION
reception will remain in that state until the device
wakes. After the device returns to Run mode, the
module will resume transmitting and receiving data. VDD
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This SCL SCL
allows the device to be placed in Sleep mode and data
to be shifted into the SPI Transmit/Receive Shift VDD
Master Slave
register. When all eight bits have been received, the
MSSP interrupt flag bit will be set and if enabled, will
SDA SDA
wake the device.

32.3 I2C MODE OVERVIEW


The Inter-Integrated Circuit (I2C) bus is a multi-master The line is held high to indicate Start and Stop bits.
serial data communication bus. Devices communicate On the last byte of data communicated, the master
in a master/slave environment where the master device may end the transmission by sending a Stop bit.
devices initiate the communication. A slave device is If the master device is in Receive mode, it sends the
controlled through addressing. Stop bit in place of the last ACK bit. A Stop bit is
The I2C bus specifies two signal connections: indicated by a low-to-high transition of the SDA line
while the SCL line is held high.
• Serial Clock (SCL)
• Serial Data (SDA) In some cases, the master may want to maintain
control of the bus and re-initiate another transmission.
Figure 32-11 shows the block diagram of the MSSP If so, the master device may send a Restart condition
module when operating in I2C mode. in place of the Stop condition or last ACK bit when it is
Both the SCL and SDA connections are bidirectional in Receive mode.
open-drain lines, each requiring pull-up resistors for the The I2C bus specifies three message protocols:
supply voltage. Pulling the line to ground is considered
a logical zero and letting the line float is considered a • Single message where a master writes data to a
logical one. slave.
• Single message where a master reads data from
Figure 32-11 shows a typical connection between two a slave.
processors configured as master and slave devices. • Combined message where a master initiates a
The I2C bus can operate with one or more master minimum of two writes, or two reads, or a combi-
devices and one or more slave devices. nation of writes and reads, to one or more slaves.
There are four potential modes of operation for a given
device:
• Master Transmit mode
(master is transmitting data to a slave)
• Master Receive mode
(master is receiving data from a slave)
• Slave Transmit mode
(slave is transmitting data to a master)
• Slave Receive mode
(slave is receiving data from the master)
To begin communication, the master device sends out
a Start condition followed by the address byte of the
slave it intends to communicate with.
This is followed by a single Read/Write bit, which deter-
mines whether the master intends to transmit to or
receive data from the slave device.

 2016-2018 Microchip Technology Inc. DS40001866B-page 427


PIC16(L)F15356/75/76/85/86
32.3.1 CLOCK STRETCHING 32.4 I2C MODE OPERATION
When a slave device has not completed processing
All MSSP I2C communication is byte oriented and
data, it can delay the transfer of more data through the
shifted out MSb first. Six SFR registers and two
process of clock stretching. An addressed slave device
interrupt flags interface the module with the PIC®
may hold the SCL clock line low after receiving or send-
microcontroller and user software. Two pins, SDA and
ing a bit, indicating that it is not yet ready to continue.
SCL, are exercised by the module to communicate
The master that is communicating with the slave will
with other external I2C devices.
attempt to raise the SCL line in order to transfer the
next bit, but will detect that the clock line has not yet 32.4.1 BYTE FORMAT
been released. Because the SCL connection is open-
drain, the slave has the ability to hold that line low until All communication in I2C is done in 9-bit segments. A
it is ready to continue communicating. byte is sent from a master to a slave or vice-versa, fol-
lowed by an Acknowledge bit sent back. After the
Clock stretching allows receivers that cannot keep up eighth falling edge of the SCL line, the device output-
with a transmitter to control the flow of incoming data. ting data on the SDA changes that pin to an input and
reads in an acknowledge value on the next clock
32.3.2 ARBITRATION
pulse.
Each master device must monitor the bus for Start and
The clock signal, SCL, is provided by the master. Data
Stop bits. If the device detects that the bus is busy, it
is valid to change while the SCL signal is low, and
cannot begin a new message until the bus returns to an
sampled on the rising edge of the clock. Changes on
Idle state.
the SDA line while the SCL line is high define special
However, two master devices may try to initiate a trans- conditions on the bus, explained below.
mission on or about the same time. When this occurs,
the process of arbitration begins. Each transmitter 32.4.2 DEFINITION OF I2C TERMINOLOGY
checks the level of the SDA data line and compares it There is language and terminology in the description
to the level that it expects to find. The first transmitter to of I2C communication that have definitions specific to
observe that the two levels do not match, loses arbitra- I2C. That word usage is defined below and may be
tion, and must stop transmitting on the SDA line. used in the rest of this document without explanation.
For example, if one transmitter holds the SDA line to a This table was adapted from the Philips I2C
logical one (lets it float) and a second transmitter holds specification.
it to a logical zero (pulls it low), the result is that the
SDA line will be low. The first transmitter then observes 32.4.3 SDA AND SCL PINS
that the level of the line is different than expected and Selection of any I2C mode with the SSPEN bit set,
concludes that another transmitter is communicating. forces the SCL and SDA pins to be open-drain. These
The first transmitter to notice this difference is the one pins should be set by the user to inputs by setting the
that loses arbitration and must stop driving the SDA appropriate TRIS bits.
line. If this transmitter is also a master device, it also
Note 1: Any device pin can be selected for SDA
must stop driving the SCL line. It then can monitor the
and SCL functions with the PPS periph-
lines for a Stop condition before trying to reissue its
eral. These functions are bidirectional.
transmission. In the meantime, the other device that
The SDA input is selected with the
has not noticed any difference between the expected
SSPDATPPS registers. The SCL input is
and actual levels on the SDA line continues with its
selected with the SSPCLKPPS registers.
original transmission.
Outputs are selected with the RxyPPS
Slave Transmit mode can also be arbitrated, when a registers. It is the user’s responsibility to
master addresses multiple slaves, but this is less make the selections so that both the input
common. and the output for each function is on the
same pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 428


PIC16(L)F15356/75/76/85/86
32.4.4 SDA HOLD TIME 32.4.5 START CONDITION

The hold time of the SDA pin is selected by the SDAHT The I2C specification defines a Start condition as a
bit of the SSPxCON3 register. Hold time is the time transition of SDA from a high to a low state while SCL
SDA is held valid after the falling edge of SCL. Setting line is high. A Start condition is always generated by
the SDAHT bit selects a longer 300 ns minimum hold the master and signifies the transition of the bus from
time and may help on buses with large capacitance. an Idle to an active state. Figure 32-12 shows wave
forms for Start and Stop conditions.
TABLE 32-1: I2C BUS TERMS
32.4.6 STOP CONDITION
TERM Description
A Stop condition is a transition of the SDA line from
Transmitter The device which shifts data out low-to-high state while the SCL line is high.
onto the bus.
Receiver The device which shifts data in Note: At least one SCL low time must appear
from the bus. before a Stop is valid, therefore, if the SDA
line goes low then high again while the SCL
Master The device that initiates a transfer,
line stays high, only the Start condition is
generates clock signals and termi-
detected.
nates a transfer.
Slave The device addressed by the 32.4.7 RESTART CONDITION
master.
Multi-master A bus with more than one device A Restart is valid any time that a Stop would be valid.
that can initiate data transfers. A master can issue a Restart if it wishes to hold the
bus after terminating the current transfer. A Restart
Arbitration Procedure to ensure that only one
has the same effect on the slave that a Start would,
master at a time controls the bus.
resetting all slave logic and preparing it to clock in an
Winning arbitration ensures that
address. The master may want to address the same or
the message is not corrupted.
another slave. Figure 32-13 shows the wave form for a
Synchronization Procedure to synchronize the Restart condition.
clocks of two or more devices on
the bus. In 10-bit Addressing Slave mode a Restart is required
for the master to clock data out of the addressed
Idle No master is controlling the bus,
slave. Once a slave has been fully addressed, match-
and both SDA and SCL lines are
ing both high and low address bytes, the master can
high.
issue a Restart and the high address byte with the R/
Active Any time one or more master W bit set. The slave logic will then hold the clock and
devices are controlling the bus. prepare to clock out data.
Addressed Slave device that has received a
Slave matching address and is actively 32.4.8 START/STOP CONDITION INTERRUPT
being clocked by a master. MASKING
Matching Address byte that is clocked into a The SCIE and PCIE bits of the SSPxCON3 register
Address slave that matches the value can enable the generation of an interrupt in Slave
stored in SSPxADD. modes that do not typically support this function. Slave
Write Request Slave receives a matching modes where interrupt on Start and Stop detect are
address with R/W bit clear, and is already enabled, these bits will have no effect.
ready to clock in data.
Read Request Master sends an address byte with
the R/W bit set, indicating that it
wishes to clock data out of the
Slave. This data is the next and all
following bytes until a Restart or
Stop.
Clock Stretching When a device on the bus hold
SCL low to stall communication.
Bus Collision Any time the SDA line is sampled
low by the module while it is out-
putting and expected high state.

 2016-2018 Microchip Technology Inc. DS40001866B-page 429


PIC16(L)F15356/75/76/85/86
FIGURE 32-12: I2C START AND STOP CONDITIONS

SDA

SCL
S P
Change of Change of
Data Allowed Data Allowed
Start Stop
Condition Condition

FIGURE 32-13: I2C RESTART CONDITION

Sr

Change of Change of
Data Allowed Data Allowed
Restart
Condition

32.4.9 ACKNOWLEDGE SEQUENCE Slave software, when the AHEN and DHEN bits are
set, allow the user to set the ACK value sent back to
The 9th SCL pulse for any transferred byte in I2C is the transmitter. The ACKDT bit of the SSPxCON2
dedicated as an Acknowledge. It allows receiving register is set/cleared to determine the response.
devices to respond back to the transmitter by pulling
the SDA line low. The transmitter must release control There are certain conditions where an ACK will not be
of the line during this time to shift in the response. The sent by the slave. If the BF bit of the SSPxSTAT
Acknowledge (ACK) is an active-low signal, pulling the register or the SSPOV bit of the SSPxCON1 register
SDA line low indicates to the transmitter that the are set when a byte is received.
device has received the transmitted data and is ready When the module is addressed, after the eighth falling
to receive more. edge of SCL on the bus, the ACKTIM bit of the
The result of an ACK is placed in the ACKSTAT bit of SSPxCON3 register is set. The ACKTIM bit indicates
the SSPxCON2 register. the acknowledge time of the active bus. The ACKTIM
Status bit is only active when the AHEN bit or DHEN
bit is enabled.

 2016-2018 Microchip Technology Inc. DS40001866B-page 430


PIC16(L)F15356/75/76/85/86
32.5 I2C SLAVE MODE OPERATION 32.5.2 SLAVE RECEPTION

The MSSP Slave mode operates in one of four modes When the R/W bit of a matching received address byte
selected by the SSPM bits of SSPxCON1 register. The is clear, the R/W bit of the SSPxSTAT register is
modes can be divided into 7-bit and 10-bit Addressing cleared. The received address is loaded into the
mode. 10-bit Addressing modes operate the same as SSPxBUF register and acknowledged.
7-bit with some additional overhead for handling the When the overflow condition exists for a received
larger addresses. address, then not Acknowledge is given. An overflow
Modes with Start and Stop bit interrupts operate the condition is defined as either bit BF of the SSPxSTAT
same as the other modes with SSPxIF additionally register is set, or bit SSPOV of the SSPxCON1 register
getting set upon detection of a Start, Restart, or Stop is set. The BOEN bit of the SSPxCON3 register
condition. modifies this operation. For more information see
Register 32-4.
32.5.1 SLAVE MODE ADDRESSES
An MSSP interrupt is generated for each transferred
The SSPxADD register (Register 32-6) contains the data byte. Flag bit, SSPxIF, must be cleared by
Slave mode address. The first byte received after a software.
Start or Restart condition is compared against the When the SEN bit of the SSPxCON2 register is set,
value stored in this register. If the byte matches, the SCL will be held low (clock stretch) following each
value is loaded into the SSPxBUF register and an received byte. The clock must be released by setting
interrupt is generated. If the value does not match, the the CKP bit of the SSPxCON1 register.
module goes idle and no indication is given to the
software that anything happened. 32.5.2.1 7-bit Addressing Reception
The SSP Mask register (Register 32-5) affects the This section describes a standard sequence of events
address matching process. See Section 32.5.9 “SSP for the MSSP module configured as an I2C slave in 7-
Mask Register” for more information. bit Addressing mode. Figure 32-14 and Figure 32-15
is used as a visual reference for this description.
32.5.1.1 I2C Slave 7-bit Addressing Mode
This is a step by step process of what typically must
In 7-bit Addressing mode, the LSb of the received data be done to accomplish I2C communication.
byte is ignored when determining if there is an address
1. Start bit detected.
match.
2. S bit of SSPxSTAT is set; SSPxIF is set if
32.5.1.2 I2C Slave 10-bit Addressing Mode interrupt on Start detect is enabled.
In 10-bit Addressing mode, the first received byte is 3. Matching address with R/W bit clear is received.
compared to the binary value of ‘1 1 1 1 0 A9 A8 0’. A9 4. The slave pulls SDA low sending an ACK to the
and A8 are the two MSb’s of the 10-bit address and master, and sets SSPxIF bit.
stored in bits 2 and 1 of the SSPxADD register. 5. Software clears the SSPxIF bit.
After the acknowledge of the high byte the UA bit is set 6. Software reads received address from
and SCL is held low until the user updates SSPxADD SSPxBUF clearing the BF flag.
with the low address. The low address byte is clocked 7. If SEN = 1; Slave software sets CKP bit to
in and all eight bits are compared to the low address release the SCL line.
value in SSPxADD. Even if there is not an address 8. The master clocks out a data byte.
match; SSPxIF and UA are set, and SCL is held low 9. Slave drives SDA low sending an ACK to the
until SSPxADD is updated to receive a high byte master, and sets SSPxIF bit.
again. When SSPxADD is updated the UA bit is
10. Software clears SSPxIF.
cleared. This ensures the module is ready to receive
the high address byte on the next communication. 11. Software reads the received byte from
SSPxBUF clearing BF.
A high and low address match as a write request is
12. Steps 8-12 are repeated for all received bytes
required at the start of all 10-bit addressing communi-
from the master.
cation. A transmission can be initiated by issuing a
Restart once the slave is addressed, and clocking in 13. Master sends Stop condition, setting P bit of
the high address with the R/W bit set. The slave SSPxSTAT, and the bus goes idle.
hardware will then acknowledge the read request and
prepare to clock out data. This is only valid for a slave
after it has received a complete high and low address
byte match.

 2016-2018 Microchip Technology Inc. DS40001866B-page 431


PIC16(L)F15356/75/76/85/86
32.5.2.2 7-bit Reception with AHEN and DHEN

Slave device reception with AHEN and DHEN set


operate the same as without these options with extra
interrupts and clock stretching added after the eighth
falling edge of SCL. These additional interrupts allows
time for the slave software to decide whether it wants
to ACK the receive address or data byte.
This list describes the steps that need to be taken by
slave software to use these options for I2C
communication. Figure 32-16 displays a module using
both address and data holding. Figure 32-17 includes
the operation with the SEN bit of the SSPxCON2
register set.
1. S bit of SSPxSTAT is set; SSPxIF is set if
interrupt on Start detect is enabled.
2. Matching address with R/W bit clear is clocked
in. SSPxIF is set, and CKP is cleared in hard-
ware after the eighth falling edge of SCL.
3. Slave clears the SSPxIF.
4. Slave can look at the ACKTIM bit of the
SSPxCON3 register to determine if the SSPxIF
was after or before the ACK.
5. Slave reads the address value from SSPxBUF,
clearing the BF flag.
6. Slave sets ACK value clocked out to the master
by setting ACKDT.
7. Slave releases the clock by setting CKP in soft-
ware.
8. SSPxIF is set after an ACK, not after a NACK.
9. If SEN = 1 the slave hardware will stretch the
clock after the ACK.
10. Slave clears SSPxIF.

Note: SSPxIF is still set after the ninth falling edge


of SCL even if there is no clock stretching
and BF has been cleared. Only if NACK is
sent to master is SSPxIF not set
11. SSPxIF set, and CKP is cleared in hardware
after eighth falling edge of SCL for a received
data byte.
12. Slave looks at ACKTIM bit of SSPxCON3 to
determine the source of the interrupt.
13. Slave reads the received data from SSPxBUF
clearing BF.
14. Steps 7-14 are the same for each received data
byte.
15. Communication is ended by either the slave
sending an ACK = 1, or the master sending a
Stop condition. If a Stop is sent and Interrupt on
Stop Detect is disabled, the slave will only know
by polling the P bit of the SSPxSTAT register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 432


FIGURE 32-14: I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 0, DHEN = 0)
 2016-2018 Microchip Technology Inc.

Bus Master sends


Stop condition
From Slave to Master

Receiving Address Receiving Data Receiving Data ACK = 1


SDA
A7 A6 A5 A4 A3 A2 A1 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL

PIC16(L)F15356/75/76/85/86
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
S P

SSPxIF
SSPxIF set on 9th
Cleared by software Cleared by software falling edge of
SCL
BF
First byte
SSPxBUF is read of data is
available
in SSPxBUF
SSPOV

SSPOV set because


SSPxBUF is still full.
ACK is not sent.
DS40001866B-page 433
FIGURE 32-15: I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 0, DHEN = 0)
 2016-2018 Microchip Technology Inc.

Bus Master sends


Stop condition

Receive Address Receive Data Receive Data ACK


SDA A7 A6 A5 A4 A3 A2 A1 R/W=0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL S 1 2 3 4 5 6 7 8 9 SEN 1 2 3 4 5 6 7 8 9 SEN 1 2 3 4 5 6 7 8 9 P

PIC16(L)F15356/75/76/85/86
Clock is held low until CKP is set to ‘1’

SSPxIF

SSPxIF set on 9th


Cleared by software Cleared by software falling edge of SCL

BF
First byte
of data is
SSPxBUF is read available
in SSPxBUF
SSPOV

SSPOV set because


SSPxBUF is still full.
ACK is not sent.

CKP

SCL is not held


CKP is written to ‘1’ in software, CKP is written to ‘1’ in software,
DS40001866B-page 434

low because
releasing SCL releasing SCL
ACK= 1
FIGURE 32-16: I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 1, DHEN = 1)
 2016-2018 Microchip Technology Inc.

Master Releases SDA Master sends


to slave for ACK sequence Stop condition

SDA Receiving Address Receiving Data ACK Received Data ACK=1


A7 A6 A5 A4 A3 A2 A1 ACK D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0

SCL
S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P

SSPxIF
If AHEN = 1: SSPxIF is set on
SSPxIF is set 9th falling edge of Cleared by software No interrupt
SCL, after ACK after not ACK

PIC16(L)F15356/75/76/85/86
BF from Slave
Address is
read from Data is read from SSPxBUF
ACKDT SSPxBUF

Slave software
clears ACKDT to Slave software
ACK the received sets ACKDT to
CKP byte not ACK

When AHEN = 1:
When DHEN = 1: CKP set by software,
CKP is cleared by hardware
CKP is cleared by SCL is released
and SCL is stretched hardware on 8th falling
edge of SCL
ACKTIM

ACKTIM set by hardware ACKTIM cleared by ACKTIM set by hardware


on 8th falling edge of SCL hardware in 9th on 8th falling edge of SCL
rising edge of SCL
DS40001866B-page 435

P
FIGURE 32-17: I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 1, DHEN = 1)
 2016-2018 Microchip Technology Inc.

Master sends
Stop condition
Master releases
R/W = 0 SDA to slave for ACK sequence
Receiving Address Receive Data Receive Data ACK
SDA ACK
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P
S

SSPxIF
Cleared by software No interrupt after

PIC16(L)F15356/75/76/85/86
if not ACK
from Slave
BF
Received
address is loaded into Received data is SSPxBUF can be
SSPxBUF available on SSPxBUF read any time before
next byte is loaded
ACKDT

Slave software clears


Slave sends
ACKDT to ACK not ACK
the received byte
CKP
When AHEN = 1; When DHEN = 1; CKP is not cleared
on the 8th falling edge on the 8th falling edge Set by software, if not ACK
of SCL of an address of SCL of a received release SCL
byte, CKP is cleared data byte, CKP is cleared

ACKTIM

ACKTIM is set by hardware ACKTIM is cleared by hardware


on 8th falling edge of SCL on 9th rising edge of SCL
DS40001866B-page 436

P
PIC16(L)F15356/75/76/85/86
32.5.3 SLAVE TRANSMISSION 32.5.3.2 7-bit Transmission
When the R/W bit of the incoming address byte is set A master device can transmit a read request to a
and an address match occurs, the R/W bit of the slave, and then clock data out of the slave. The list
SSPxSTAT register is set. The received address is below outlines what software for a slave will need to
loaded into the SSPxBUF register, and an ACK pulse is do to accomplish a standard transmission. Figure 32-
sent by the slave on the ninth bit. 18 can be used as a reference to this list.
Following the ACK, slave hardware clears the CKP bit 1. Master sends a Start condition on SDA and
and the SCL pin is held low (see Section 32.5.6 SCL.
“Clock Stretching” for more detail). By stretching the 2. S bit of SSPxSTAT is set; SSPxIF is set if
clock, the master will be unable to assert another clock interrupt on Start detect is enabled.
pulse until the slave is done preparing the transmit 3. Matching address with R/W bit set is received by
data. the Slave setting SSPxIF bit.
The transmit data must be loaded into the SSPxBUF 4. Slave hardware generates an ACK and sets
register which also loads the SSPxSR register. Then SSPxIF.
the SCL pin should be released by setting the CKP bit 5. SSPxIF bit is cleared by software.
of the SSPxCON1 register. The eight data bits are
6. Software reads the received address from
shifted out on the falling edge of the SCL input. This
SSPxBUF, clearing BF.
ensures that the SDA signal is valid during the SCL
high time. 7. R/W is set so CKP was automatically cleared by
hardware after the ACK.
The ACK pulse from the master-receiver is latched on
8. The slave software loads the transmit data into
the rising edge of the ninth SCL input pulse. This ACK
SSPxBUF.
value is copied to the ACKSTAT bit of the SSPxCON2
register. If ACKSTAT is set (not ACK), then the data 9. CKP bit is set in software, releasing SCL, allow-
transfer is complete. In this case, when the not ACK is ing the master to clock the data out of the slave.
latched by the slave, the slave goes idle and waits for 10. SSPxIF is set after the ACK response from the
another occurrence of the Start bit. If the SDA line was master is loaded into the ACKSTAT bit.
low (ACK), the next transmit data must be loaded into 11. SSPxIF bit is cleared.
the SSPxBUF register. Again, the SCL pin must be 12. The slave software checks the ACKSTAT bit to
released by setting bit CKP. see if the master wants to clock out more data.
An MSSP interrupt is generated for each data transfer Note 1:If the master ACKs the clock will be
byte. The SSPxIF bit must be cleared by software and stretched.
the SSPxSTAT register is used to determine the status
of the byte. The SSPxIF bit is set on the falling edge of 2: ACKSTAT is the only bit updated on the
the ninth clock pulse. rising edge of SCL (9th) rather than the
falling.
32.5.3.1 Slave Mode Bus Collision 13. Steps 9-13 are repeated for each transmitted
A slave receives a read request and begins shifting byte.
data out on the SDA line. If a bus collision is detected 14. If the master sends a not ACK; the clock is not
and the SBCDE bit of the SSPxCON3 register is set, held, but SSPxIF is still set.
the BCL1IF bit of the PIR3 register is set. Once a bus 15. The master sends a Restart condition or a Stop.
collision is detected, the slave goes idle and waits to be
16. The slave is no longer addressed.
addressed again. User software can use the BCL1IF bit
to handle a slave bus collision.

 2016-2018 Microchip Technology Inc. DS40001866B-page 437


FIGURE 32-18: I2C SLAVE, 7-BIT ADDRESS, TRANSMISSION (AHEN = 0)
 2016-2018 Microchip Technology Inc.

Master sends
Stop condition

Receiving Address Automatic Transmitting Data Automatic Transmitting Data ACK


R/W = 1
SDA A7 A6 A5 A4 A3 A2 A1 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
S P

SSPxIF

Cleared by software

BF
BF is automatically

PIC16(L)F15356/75/76/85/86
Received address Data to transmit is cleared after 8th falling
is read from SSPxBUF loaded into SSPxBUF edge of SCL

CKP
When R/W is set CKP is not
SCL is always held for not
held low after 9th SCL Set by software ACK
falling edge
ACKSTAT

Masters not ACK


is copied to
ACKSTAT
R/W
R/W is copied from the
matching address byte
D/A

Indicates an address
has been received
DS40001866B-page 438

P
PIC16(L)F15356/75/76/85/86
32.5.3.3 7-bit Transmission with Address
Hold Enabled
Setting the AHEN bit of the SSPxCON3 register
enables additional clock stretching and interrupt
generation after the eighth falling edge of a received
matching address. Once a matching address has
been clocked in, CKP is cleared and the SSPxIF
interrupt is set.
Figure 32-19 displays a standard waveform of a 7-bit
address slave transmission with AHEN enabled.
1. Master sends Start condition; the S bit of
SSPxSTAT is set; SSPxIF is set if interrupt on
Start detect is enabled.
2. Master sends matching address with R/W bit
set. After the eighth falling edge of the SCL line
the CKP bit is cleared by hardware and SSPxIF
interrupt is generated.
3. Slave software clears SSPxIF.
4. Slave software reads ACKTIM bit of SSPxCON3
register, and R/W and D/A of the SSPxSTAT
register to determine the source of the interrupt.
5. Slave reads the address value from the
SSPxBUF register clearing the BF bit.
6. Slave software decides from this information if it
wishes to ACK or not ACK and sets the ACKDT
bit of the SSPxCON2 register accordingly.
7. Slave software sets the CKP bit releasing SCL.
8. Master clocks in the ACK value from the slave.
9. Slave hardware automatically clears the CKP bit
and sets SSPxIF after the ACK if the R/W bit is
set.
10. Slave software clears SSPxIF.
11. Slave loads value to transmit to the master into
SSPxBUF setting the BF bit.
Note: SSPxBUF cannot be loaded until after the
ACK.
12. Slave sets the CKP bit releasing the clock.
13. Master clocks out the data from the slave and
sends an ACK value on the ninth SCL pulse.
14. Slave hardware copies the ACK value into the
ACKSTAT bit of the SSPxCON2 register.
15. Steps 10-15 are repeated for each byte transmit-
ted to the master from the slave.
16. If the master sends a not ACK the slave
releases the bus allowing the master to send a
Stop and end the communication.
Note: Master must send a not ACK on the last
byte to ensure that the slave releases the
SCL line to receive a Stop.

 2016-2018 Microchip Technology Inc. DS40001866B-page 439


FIGURE 32-19: I2C SLAVE, 7-BIT ADDRESS, TRANSMISSION (AHEN = 1)
 2016-2018 Microchip Technology Inc.

Master sends
Master releases SDA Stop condition
to slave for ACK sequence
Receiving Address R/W = 1 Automatic Transmitting Data
Automatic Transmitting Data ACK
SDA ACK ACK
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0

SCL
S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
P

SSPxIF
Cleared by software

BF BF is automatically
Received address Data to transmit is cleared after 8th falling

PIC16(L)F15356/75/76/85/86
is read from SSPxBUF loaded into SSPxBUF edge of SCL

ACKDT

Slave clears
ACKDT to ACK
address

ACKSTAT
Master’s ACK
response is copied
to SSPxSTAT
CKP
When AHEN = 1; CKP not cleared
CKP is cleared by hardware When R/W = 1; Set by software, after not ACK
after receiving matching CKP is always releases SCL
address. cleared after ACK

ACKTIM
ACKTIM is set on 8th falling ACKTIM is cleared
edge of SCL on 9th rising edge of SCL
DS40001866B-page 440

R/W

D/A
PIC16(L)F15356/75/76/85/86
32.5.4 SLAVE MODE 10-BIT ADDRESS 32.5.5 10-BIT ADDRESSING WITH ADDRESS OR
RECEPTION DATA HOLD
This section describes a standard sequence of events Reception using 10-bit addressing with AHEN or
for the MSSP module configured as an I2C slave in 10- DHEN set is the same as with 7-bit modes. The only
bit Addressing mode. difference is the need to update the SSPxADD register
Figure 32-20 is used as a visual reference for this using the UA bit. All functionality, specifically when the
description. CKP bit is cleared and SCL line is held low are the
same. Figure 32-21 can be used as a reference of a
This is a step by step process of what must be done by slave in 10-bit addressing with AHEN set.
slave software to accomplish I2C communication.
Figure 32-22 shows a standard waveform for a slave
1. Master sends Start condition; S bit of SSPxSTAT transmitter in 10-bit Addressing mode.
is set; SSPxIF is set if interrupt on Start detect is
enabled.
2. Master sends matching high address with R/W
bit clear; UA bit of the SSPxSTAT register is set.
3. Slave sends ACK and SSPxIF is set.
4. Software clears the SSPxIF bit.
5. Software reads received address from
SSPxBUF clearing the BF flag.
6. Slave loads low address into SSPxADD,
releasing SCL.
7. Master sends matching low address byte to the
slave; UA bit is set.
Note: Updates to the SSPxADD register are not
allowed until after the ACK sequence.

8. Slave sends ACK and SSPxIF is set.


Note: If the low address does not match, SSPxIF
and UA are still set so that the slave
software can set SSPxADD back to the high
address. BF is not set because there is no
match. CKP is unaffected.
9. Slave clears SSPxIF.
10. Slave reads the received matching address
from SSPxBUF clearing BF.
11. Slave loads high address into SSPxADD.
12. Master clocks a data byte to the slave and
clocks out the slaves ACK on the ninth SCL
pulse; SSPxIF is set.
13. If SEN bit of SSPxCON2 is set, CKP is cleared
by hardware and the clock is stretched.
14. Slave clears SSPxIF.
15. Slave reads the received byte from SSPxBUF
clearing BF.
16. If SEN is set the slave software sets CKP to
release the SCL.
17. Steps 13-17 repeat for each received byte.
18. Master sends Stop to end the transmission.

 2016-2018 Microchip Technology Inc. DS40001866B-page 441


FIGURE 32-20: I2C SLAVE, 10-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 0, DHEN = 0)
 2016-2018 Microchip Technology Inc.

Master sends
Stop condition

Receive First Address Byte Receive Second Address Byte Receive Data Receive Data
SDA
1 1 1 1
0 A9 A8 ACK A7 A6 A5 A4 A3 A2 A1 A0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK

SCL
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P
S
SCL is held low
while CKP = 0

PIC16(L)F15356/75/76/85/86
SSPxIF
Set by hardware Cleared by software
on 9th falling edge

BF
If address matches Receive address is Data is read
SSPxADD it is loaded into read from SSPxBUF from SSPxBUF
SSPxBUF

UA
When UA = 1; Software updates SSPxADD
SCL is held low and releases SCL

CKP

When SEN = 1; Set by software,


DS40001866B-page 442

CKP is cleared after releasing SCL


9th falling edge of received byte
FIGURE 32-21: I2C SLAVE, 10-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 1, DHEN = 0)
 2016-2018 Microchip Technology Inc.

Receive First Address Byte R/W = 0 Receive Second Address Byte Receive Data Receive Data
SDA 1 1 1 1 0 A9 A8 ACK A7 A6 A5 A4 A3 A2 A1 A0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5

SCL S 1 2 3 4 5 6 7 8 9 UA 1 2 3 4 5 6 7 8 9 UA 1 2 3 4 5 6 7 8 9 1 2

SSPxIF
Set by hardware Cleared by software Cleared by software
on 9th falling edge

PIC16(L)F15356/75/76/85/86
BF

SSPxBUF can be Received data


read anytime before is read from
the next received byte SSPxBUF
ACKDT
Slave software clears
ACKDT to ACK
the received byte

UA

Update to SSPxADD is Update of SSPxADD,


not allowed until 9th
clears UA and releases
falling edge of SCL
SCL

CKP If when AHEN = 1;


on the 8th falling edge
DS40001866B-page 443

Set CKP with software


of SCL of an address releases SCL
byte, CKP is cleared
ACKTIM
ACKTIM is set by hardware
on 8th falling edge of SCL
FIGURE 32-22: I2C SLAVE, 10-BIT ADDRESS, TRANSMISSION (SEN = 0, AHEN = 0, DHEN = 0)
 2016-2018 Microchip Technology Inc.

Master sends
Master sends Stop condition
Restart event Master sends
not ACK

Receiving Address R/W = 0 Receiving Second Address Byte Receive First Address Byte Transmitting Data Byte ACK = 1
SDA 1 1 1 1 0 A9 A8 ACK A7 A6 A5 A4 A3 A2 A1 A0 ACK 1 1 1 1 0 A9 A8 ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P
S
Sr

SSPxIF

PIC16(L)F15356/75/76/85/86
Set by hardware Cleared by software Set by hardware

BF

SSPxBUF loaded Received address is Data to transmit is


with received address read from SSPxBUF loaded into SSPxBUF
UA
High address is loaded
UA indicates SSPxADD After SSPxADD is back into SSPxADD
must be updated updated, UA is cleared
CKP and SCL is released

When R/W = 1; Set by software


ACKSTAT CKP is cleared on releases SCL
9th falling edge of SCL

Masters not ACK


is copied
R/W
R/W is copied from the
matching address byte
DS40001866B-page 444

D/A

Indicates an address
has been received
PIC16(L)F15356/75/76/85/86
32.5.6 CLOCK STRETCHING 32.5.6.3 Byte NACKing
Clock stretching occurs when a device on the bus When AHEN bit of SSPxCON3 is set; CKP is cleared
holds the SCL line low, effectively pausing communi- by hardware after the eighth falling edge of SCL for a
cation. The slave may stretch the clock to allow more received matching address byte. When DHEN bit of
time to handle data or prepare a response for the SSPxCON3 is set; CKP is cleared after the eighth fall-
master device. A master device is not concerned with ing edge of SCL for received data.
stretching as anytime it is active on the bus and not Stretching after the eighth falling edge of SCL allows
transferring data it is stretching. Any stretching done the slave to look at the received address or data and
by a slave is invisible to the master software and decide if it wants to ACK the received data.
handled by the hardware that generates SCL.
The CKP bit of the SSPxCON1 register is used to 32.5.7 CLOCK SYNCHRONIZATION AND THE
control stretching. Any time the CKP bit is cleared, the CKP BIT
module will wait for the SCL line to go low and then Any time the CKP bit is cleared, the module will wait
hold it. Setting CKP will release SCL and allow more for the SCL line to go low and then hold it. However,
communication. clearing the CKP bit will not assert the SCL output low
32.5.6.1 Normal Clock Stretching until the SCL output is already sampled low. There-
fore, the CKP bit will not assert the SCL line until an
Following an ACK if the R/W bit of SSPxSTAT is set, a external I2C master device has already asserted the
read request, the slave hardware will clear CKP. This SCL line. The SCL output will remain low until the CKP
allows the slave time to update SSPxBUF with data to bit is set and all other devices on the I2C bus have
transfer to the master. If the SEN bit of SSPxCON2 is released SCL. This ensures that a write to the CKP bit
set, the slave hardware will always stretch the clock will not violate the minimum high time requirement for
after the ACK sequence. Once the slave is ready; CKP SCL (see Figure 32-23).
is set by software and communication resumes.

32.5.6.2 10-bit Addressing Mode

In 10-bit Addressing mode, when the UA bit is set the


clock is always stretched. This is the only time the SCL
is stretched without CKP being cleared. SCL is
released immediately after a write to SSPxADD.

FIGURE 32-23: CLOCK SYNCHRONIZATION TIMING

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

SDA DX DX ‚ – 1

SCL

Master device
CKP asserts clock

Master device
releases clock
WR
SSPxCON1

 2016-2018 Microchip Technology Inc. DS40001866B-page 445


PIC16(L)F15356/75/76/85/86
32.5.8 GENERAL CALL ADDRESS SUPPORT In 10-bit Address mode, the UA bit will not be set on
the reception of the general call address. The slave
The addressing procedure for the I2C bus is such that will prepare to receive the second byte as data, just as
the first byte after the Start condition usually deter- it would in 7-bit mode.
mines which device will be the slave addressed by the
master device. The exception is the general call If the AHEN bit of the SSPxCON3 register is set, just
address which can address all devices. When this as with any other address reception, the slave hard-
address is used, all devices should, in theory, respond ware will stretch the clock after the eighth falling edge
with an acknowledge. of SCL. The slave must then set its ACKDT value and
release the clock with communication progressing as it
The general call address is a reserved address in the would normally.
I2C protocol, defined as address 0x00. When the
GCEN bit of the SSPxCON2 register is set, the slave
module will automatically ACK the reception of this
address regardless of the value stored in SSPxADD.
After the slave clocks in an address of all zeros with
the R/W bit clear, an interrupt is generated and slave
software can read SSPxBUF and respond. Figure 32-
24 shows a general call reception sequence.

FIGURE 32-24: SLAVE MODE GENERAL CALL ADDRESS SEQUENCE


Address is compared to General Call Address
after ACK, set interrupt

R/W = 0 Receiving Data ACK


SDA General Call Address ACK D7 D6 D5 D4 D3 D2 D1 D0

SCL
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
S

SSPxIF

BF (SSPxSTAT<0>)

Cleared by software
SSPxBUF is read
GCEN (SSPxCON2<7>)
’1’

32.5.9 SSP MASK REGISTER This register is reset to all ‘1’s upon any Reset
condition and, therefore, has no effect on standard
An SSP Mask (SSPxMSK) register (Register 32-5) is SSP operation until written with a mask value.
available in I2C Slave mode as a mask for the value
held in the SSPxSR register during an address The SSP Mask register is active during:
comparison operation. A zero (‘0’) bit in the SSPxMSK • 7-bit Address mode: address compare of A<7:1>.
register has the effect of making the corresponding bit • 10-bit Address mode: address compare of A<7:0>
of the received address a “don’t care”. only. The SSP mask has no effect during the
reception of the first (high) byte of the address.

 2016-2018 Microchip Technology Inc. DS40001866B-page 446


PIC16(L)F15356/75/76/85/86
32.6 I2C Master Mode 32.6.1 I2C MASTER MODE OPERATION

Master mode is enabled by setting and clearing the The master device generates all of the serial clock
appropriate SSPM bits in the SSPxCON1 register and pulses and the Start and Stop conditions. A transfer is
by setting the SSPEN bit. In Master mode, the SDA and ended with a Stop condition or with a Repeated Start
SCK pins must be configured as inputs. The MSSP condition. Since the Repeated Start condition is also
peripheral hardware will override the output driver TRIS the beginning of the next serial transfer, the I2C bus will
controls when necessary to drive the pins low. not be released.
Master mode of operation is supported by interrupt In Master Transmitter mode, serial data is output
generation on the detection of the Start and Stop through SDA, while SCL outputs the serial clock. The
conditions. The Stop (P) and Start (S) bits are cleared first byte transmitted contains the slave address of the
from a Reset or when the MSSP module is disabled. receiving device (7 bits) and the Read/Write (R/W) bit.
Control of the I 2C bus may be taken when the P bit is In this case, the R/W bit will be logic ‘0’. Serial data is
set, or the bus is Idle. transmitted eight bits at a time. After each byte is
transmitted, an Acknowledge bit is received. Start and
In Firmware Controlled Master mode, user code
Stop conditions are output to indicate the beginning
conducts all I 2C bus operations based on Start and
and the end of a serial transfer.
Stop bit condition detection. Start and Stop condition
detection is the only active circuitry in this mode. All In Master Receive mode, the first byte transmitted
other communication is done by the user software contains the slave address of the transmitting device
directly manipulating the SDA and SCL lines. (7 bits) and the R/W bit. In this case, the R/W bit will be
logic ‘1’. Thus, the first byte transmitted is a 7-bit slave
The following events will cause the SSP Interrupt Flag address followed by a ‘1’ to indicate the receive bit.
bit, SSPxIF, to be set (SSP interrupt, if enabled): Serial data is received via SDA, while SCL outputs the
• Start condition generated serial clock. Serial data is received eight bits at a time.
• Stop condition generated After each byte is received, an Acknowledge bit is
transmitted. Start and Stop conditions indicate the
• Data transfer byte transmitted/received
beginning and end of transmission.
• Acknowledge transmitted/received
A Baud Rate Generator is used to set the clock
• Repeated Start generated
frequency output on SCL. See Section 32.7 “Baud
Note 1:The MSSP module, when configured in I2C Rate Generator” for more detail.
Master mode, does not allow queuing of
events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPxBUF register
to initiate transmission before the Start
condition is complete. In this case, the
SSPxBUF will not be written to and the
WCOL bit will be set, indicating that a
write to the SSPxBUF did not occur
2: When in Master mode, Start/Stop
detection is masked and an interrupt is
generated when the SEN/PEN bit is
cleared and the generation is complete.

 2016-2018 Microchip Technology Inc. DS40001866B-page 447


PIC16(L)F15356/75/76/85/86
32.6.2 CLOCK ARBITRATION

Clock arbitration occurs when the master, during any


receive, transmit or Repeated Start/Stop condition,
releases the SCL pin (SCL allowed to float high). When
the SCL pin is allowed to float high, the Baud Rate
Generator (BRG) is suspended from counting until the
SCL pin is actually sampled high. When the SCL pin is
sampled high, the Baud Rate Generator is reloaded
with the contents of SSPxADD<7:0> and begins count-
ing. This ensures that the SCL high time will always be
at least one BRG rollover count in the event that the
clock is held low by an external device (Figure 32-25).

FIGURE 32-25: BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION

SDA DX DX ‚ – 1

SCL deasserted but slave holds SCL allowed to transition high


SCL low (clock arbitration)
SCL

BRG decrements on
Q2 and Q4 cycles

BRG
03h 02h 01h 00h (hold off) 03h 02h
Value

SCL is sampled high, reload takes


place and BRG starts its count
BRG
Reload

32.6.3 WCOL STATUS FLAG

If the user writes the SSPxBUF when a Start, Restart,


Stop, Receive or Transmit sequence is in progress, the
WCOL is set and the contents of the buffer are
unchanged (the write does not occur). Any time the
WCOL bit is set it indicates that an action on SSPxBUF
was attempted while the module was not idle.
Note: Because queuing of events is not allowed,
writing to the lower five bits of SSPxCON2
is disabled until the Start condition is
complete.

 2016-2018 Microchip Technology Inc. DS40001866B-page 448


PIC16(L)F15356/75/76/85/86
32.6.4 I2C MASTER MODE START by hardware; the Baud Rate Generator is suspended,
CONDITION TIMING leaving the SDA line held low and the Start condition is
complete.
To initiate a Start condition (Figure 32-26), the user
sets the Start Enable bit, SEN bit of the SSPxCON2
register. If the SDA and SCL pins are sampled high, Note 1:If at the beginning of the Start condition, the
the Baud Rate Generator is reloaded with the contents SDA and SCL pins are already sampled
of SSPxADD<7:0> and starts its count. If SCL and low, or if during the Start condition, the
SDA are both sampled high when the Baud Rate Gen- SCL line is sampled low before the SDA
erator times out (TBRG), the SDA pin is driven low. The line is driven low, a bus collision occurs,
action of the SDA being driven low while SCL is high is the Bus Collision Interrupt Flag, BCLIF, is
the Start condition and causes the S bit of the set, the Start condition is aborted and the
SSPxSTAT1 register to be set. Following this, the I2C module is reset into its Idle state.
Baud Rate Generator is reloaded with the contents of
2: The Philips I2C specification states that a
SSPxADD<7:0> and resumes its count. When the
bus collision cannot occur on a Start.
Baud Rate Generator times out (TBRG), the SEN bit of
the SSPxCON2 register will be automatically cleared

FIGURE 32-26: FIRST START BIT TIMING

Write to SEN bit occurs here Set S bit (SSPxSTAT<3>)

At completion of Start bit,


SDA = 1,
SCL = 1 hardware clears SEN bit
and sets SSPxIF bit
TBRG TBRG Write to SSPxBUF occurs here
SDA 1st bit 2nd bit

TBRG
SCL
S
TBRG

 2016-2018 Microchip Technology Inc. DS40001866B-page 449


PIC16(L)F15356/75/76/85/86
32.6.5 I2C MASTER MODE REPEATED cally cleared and the Baud Rate Generator will not be
START CONDITION TIMING reloaded, leaving the SDA pin held low. As soon as a
Start condition is detected on the SDA and SCL pins,
A Repeated Start condition (Figure 32-27) occurs when the S bit of the SSPxSTAT register will be set. The
the RSEN bit of the SSPxCON2 register is pro- SSPxIF bit will not be set until the Baud Rate Generator
grammed high and the master state machine is no lon- has timed out.
ger active. When the RSEN bit is set, the SCL pin is
asserted low. When the SCL pin is sampled low, the Note 1: If RSEN is programmed while any other
Baud Rate Generator is loaded and begins counting. event is in progress, it will not take effect.
The SDA pin is released (brought high) for one Baud 2: A bus collision during the Repeated Start
Rate Generator count (TBRG). When the Baud Rate condition occurs if:
Generator times out, if SDA is sampled high, the SCL
pin will be deasserted (brought high). When SCL is •SDA is sampled low when SCL goes
sampled high, the Baud Rate Generator is reloaded from low-to-high.
and begins counting. SDA and SCL must be sampled •SCL goes low before SDA is
high for one TBRG. This action is then followed by asserted low. This may indicate
assertion of the SDA pin (SDA = 0) for one TBRG while that another master is attempting
SCL is high. SCL is asserted low. Following this, the to transmit a data ‘1’.
RSEN bit of the SSPxCON2 register will be automati-

FIGURE 32-27: REPEATED START CONDITION WAVEFORM

S bit set by hardware


Write to SSPxCON2
occurs here At completion of Start bit,
SDA = 1, SDA = 1,
hardware clears RSEN bit
SCL (no change) SCL = 1 and sets SSPxIF

TBRG TBRG TBRG

SDA 1st bit

Write to SSPxBUF occurs here


TBRG
SCL
Sr TBRG
Repeated Start

 2016-2018 Microchip Technology Inc. DS40001866B-page 450


PIC16(L)F15356/75/76/85/86
32.6.6 I2C MASTER MODE TRANSMISSION 32.6.6.3 ACKSTAT Status Flag
Transmission of a data byte, a 7-bit address or the In Transmit mode, the ACKSTAT bit of the SSPxCON2
other half of a 10-bit address is accomplished by simply register is cleared when the slave has sent an Acknowl-
writing a value to the SSPxBUF register. This action will edge (ACK = 0) and is set when the slave does not
set the Buffer Full flag bit, BF, and allow the Baud Rate Acknowledge (ACK = 1). A slave sends an Acknowl-
Generator to begin counting and start the next trans- edge when it has recognized its address (including a
mission. Each bit of address/data will be shifted out general call), or when the slave has properly received
onto the SDA pin after the falling edge of SCL is its data.
asserted. SCL is held low for one Baud Rate Generator
32.6.6.4 Typical transmit sequence:
rollover count (TBRG). Data should be valid before SCL
is released high. When the SCL pin is released high, it 1. The user generates a Start condition by setting
is held that way for TBRG. The data on the SDA pin the SEN bit of the SSPxCON2 register.
must remain stable for that duration and some hold 2. SSPxIF is set by hardware on completion of the
time after the next falling edge of SCL. After the eighth Start.
bit is shifted out (the falling edge of the eighth clock),
3. SSPxIF is cleared by software.
the BF flag is cleared and the master releases SDA.
This allows the slave device being addressed to 4. The MSSP module will wait the required start
respond with an ACK bit during the ninth bit time if an time before any other operation takes place.
address match occurred, or if data was received prop- 5. The user loads the SSPxBUF with the slave
erly. The status of ACK is written into the ACKSTAT bit address to transmit.
on the rising edge of the ninth clock. If the master 6. Address is shifted out the SDA pin until all eight
receives an Acknowledge, the Acknowledge Status bit, bits are transmitted. Transmission begins as
ACKSTAT, is cleared. If not, the bit is set. After the ninth soon as SSPxBUF is written to.
clock, the SSPxIF bit is set and the master clock (Baud 7. The MSSP module shifts in the ACK bit from the
Rate Generator) is suspended until the next data byte slave device and writes its value into the
is loaded into the SSPxBUF, leaving SCL low and SDA ACKSTAT bit of the SSPxCON2 register.
unchanged (Figure 32-28). 8. The MSSP module generates an interrupt at the
After the write to the SSPxBUF, each bit of the address end of the ninth clock cycle by setting the
will be shifted out on the falling edge of SCL until all SSPxIF bit.
seven address bits and the R/W bit are completed. On 9. The user loads the SSPxBUF with eight bits of
the falling edge of the eighth clock, the master will data.
release the SDA pin, allowing the slave to respond with 10. Data is shifted out the SDA pin until all eight bits
an Acknowledge. On the falling edge of the ninth clock, are transmitted.
the master will sample the SDA pin to see if the address
11. The MSSP module shifts in the ACK bit from the
was recognized by a slave. The status of the ACK bit is
slave device and writes its value into the
loaded into the ACKSTAT Status bit of the SSPxCON2
ACKSTAT bit of the SSPxCON2 register.
register. Following the falling edge of the ninth clock
transmission of the address, the SSPxIF is set, the BF 12. Steps 8-11 are repeated for all transmitted data
flag is cleared and the Baud Rate Generator is turned bytes.
off until another write to the SSPxBUF takes place, 13. The user generates a Stop or Restart condition
holding SCL low and allowing SDA to float. by setting the PEN or RSEN bits of the SSPx-
CON2 register. Interrupt is generated once the
32.6.6.1 BF Status Flag Stop/Restart condition is complete.
In Transmit mode, the BF bit of the SSPxSTAT register
is set when the CPU writes to SSPxBUF and is cleared
when all eight bits are shifted out.

32.6.6.2 WCOL Status Flag


If the user writes the SSPxBUF when a transmit is
already in progress (i.e., SSPxSR is still shifting out a
data byte), the WCOL bit is set and the contents of the
buffer are unchanged (the write does not occur).
WCOL must be cleared by software before the next
transmission.

 2016-2018 Microchip Technology Inc. DS40001866B-page 451


FIGURE 32-28: I2C MASTER MODE WAVEFORM (TRANSMISSION, 7 OR 10-BIT ADDRESS)
 2016-2018 Microchip Technology Inc.

Write SSPxCON2<0> SEN = 1 ACKSTAT in


Start condition begins SSPxCON2 = 1
From slave, clear ACKSTAT bit SSPxCON2<6>
SEN = 0
Transmitting Data or Second Half
Transmit Address to Slave R/W = 0
of 10-bit Address ACK

SDA A7 A6 A5 A4 A3 A2 A1 ACK = 0 D7 D6 D5 D4 D3 D2 D1 D0

SSPxBUF written with 7-bit address and R/W


start transmit
SCL 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
S P
SCL held low

PIC16(L)F15356/75/76/85/86
while CPU
responds to SSPxIF
SSPxIF
Cleared by software service routine
Cleared by software from SSP interrupt
Cleared by software

BF (SSPxSTAT<0>)

SSPxBUF written SSPxBUF is written by software


SEN

After Start condition, SEN cleared by hardware

PEN
DS40001866B-page 452

R/W
PIC16(L)F15356/75/76/85/86
32.6.7 I2C MASTER MODE RECEPTION 32.6.7.4 Typical Receive Sequence:
Master mode reception (Figure 32-29) is enabled by 1. The user generates a Start condition by setting
programming the Receive Enable bit, RCEN bit of the the SEN bit of the SSPxCON2 register.
SSPxCON2 register. 2. SSPxIF is set by hardware on completion of the
Note: The MSSP module must be in an Idle Start.
state before the RCEN bit is set or the 3. SSPxIF is cleared by software.
RCEN bit will be disregarded. 4. User writes SSPxBUF with the slave address to
The Baud Rate Generator begins counting and on each transmit and the R/W bit set.
rollover, the state of the SCL pin changes (high-to-low/ 5. Address is shifted out the SDA pin until all eight
low-to-high) and data is shifted into the SSPxSR. After bits are transmitted. Transmission begins as
the falling edge of the eighth clock, the receive enable soon as SSPxBUF is written to.
flag is automatically cleared, the contents of the 6. The MSSP module shifts in the ACK bit from the
SSPxSR are loaded into the SSPxBUF, the BF flag bit slave device and writes its value into the
is set, the SSPxIF flag bit is set and the Baud Rate ACKSTAT bit of the SSPxCON2 register.
Generator is suspended from counting, holding SCL 7. The MSSP module generates an interrupt at the
low. The MSSP is now in Idle state awaiting the next end of the ninth clock cycle by setting the
command. When the buffer is read by the CPU, the BF SSPxIF bit.
flag bit is automatically cleared. The user can then 8. User sets the RCEN bit of the SSPxCON2
send an Acknowledge bit at the end of reception by set- register and the master clocks in a byte from the
ting the Acknowledge Sequence Enable, ACKEN bit of slave.
the SSPxCON2 register.
9. After the eighth falling edge of SCL, SSPxIF and
32.6.7.1 BF Status Flag BF are set.
10. Master clears SSPxIF and reads the received
In receive operation, the BF bit is set when an address
byte from SSPxBUF, clears BF.
or data byte is loaded into SSPxBUF from SSPxSR. It
is cleared when the SSPxBUF register is read. 11. Master sets ACK value sent to slave in ACKDT
bit of the SSPxCON2 register and initiates the
32.6.7.2 SSPOV Status Flag ACK by setting the ACKEN bit.
In receive operation, the SSPOV bit is set when eight 12. Master’s ACK is clocked out to the slave and
bits are received into the SSPxSR and the BF flag bit is SSPxIF is set.
already set from a previous reception. 13. User clears SSPxIF.
14. Steps 8-13 are repeated for each received byte
32.6.7.3 WCOL Status Flag from the slave.
If the user writes the SSPxBUF when a receive is 15. Master sends a not ACK or Stop to end
already in progress (i.e., SSPxSR is still shifting in a communication.
data byte), the WCOL bit is set and the contents of the
buffer are unchanged (the write does not occur).

 2016-2018 Microchip Technology Inc. DS40001866B-page 453


FIGURE 32-29: I2C MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS)
 2016-2018 Microchip Technology Inc.

Write to SSPxCON2<4>
to start Ackno1wledge sequence
SDA = ACKDT (SSPxCON2<5>) = 0
Write to SSPxCON2<0>(SEN = 1),
begin Start condition ACK from Master Set ACKEN, start Acknowledge sequence
Master configured as a receiver SDA = ACKDT = 0 SDA = ACKDT = 1
SEN = 0 by programming SSPxCON2<3> (RCEN = 1)
PEN bit = 1
Write to SSPxBUF occurs here, RCEN cleared RCEN = 1, start RCEN cleared
ACK from Slave next receive automatically written here
start XMIT automatically
Transmit Address to Slave Receiving Data from Slave Receiving Data from Slave
SDA A7 A6 A5 A4 A3 A2 A1 R/W ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK

Bus master
ACK is not sent terminates
transfer
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
SCL S P
Data shifted in on falling edge of CLK Set SSPxIF at end

PIC16(L)F15356/75/76/85/86
of receive Set SSPxIF interrupt
Set SSPxIF interrupt at end of Acknow-
Set SSPxIF interrupt ledge sequence
at end of receive at end of Acknowledge
SSPxIF sequence

Set P bit
Cleared by software Cleared by software Cleared by software Cleared by software (SSPxSTAT<4>)
SDA = 0, SCL = 1 Cleared in
while CPU software and SSPxIF
responds to SSPxIF

BF
(SSPxSTAT<0>) Last bit is shifted into SSPxSR and
contents are unloaded into SSPxBUF

SSPOV

SSPOV is set because


SSPxBUF is still full

ACKEN
DS40001866B-page 454

RCEN

Master configured as a receiver RCEN cleared ACK from Master RCEN cleared
by programming SSPxCON2<3> (RCEN = 1) automatically SDA = ACKDT = 0 automatically
PIC16(L)F15356/75/76/85/86
32.6.8 ACKNOWLEDGE SEQUENCE 32.6.9 STOP CONDITION TIMING
TIMING A Stop bit is asserted on the SDA pin at the end of a
An Acknowledge sequence is enabled by setting the receive/transmit by setting the Stop Sequence Enable
Acknowledge Sequence Enable bit, ACKEN bit of the bit, PEN bit of the SSPxCON2 register. At the end of a
SSPxCON2 register. When this bit is set, the SCL pin is receive/transmit, the SCL line is held low after the
pulled low and the contents of the Acknowledge data bit falling edge of the ninth clock. When the PEN bit is set,
are presented on the SDA pin. If the user wishes to the master will assert the SDA line low. When the SDA
generate an Acknowledge, then the ACKDT bit should line is sampled low, the Baud Rate Generator is
be cleared. If not, the user should set the ACKDT bit reloaded and counts down to ‘0’. When the Baud Rate
before starting an Acknowledge sequence. The Baud Generator times out, the SCL pin will be brought high
Rate Generator then counts for one rollover period and one TBRG (Baud Rate Generator rollover count)
(TBRG) and the SCL pin is deasserted (pulled high). later, the SDA pin will be deasserted. When the SDA
When the SCL pin is sampled high (clock arbitration), pin is sampled high while SCL is high, the P bit of the
the Baud Rate Generator counts for TBRG. The SCL pin SSPxSTAT register is set. A TBRG later, the PEN bit is
is then pulled low. Following this, the ACKEN bit is auto- cleared and the SSPxIF bit is set (Figure 32-31).
matically cleared, the Baud Rate Generator is turned off
and the MSSP module then goes into IDLE mode 32.6.9.1 WCOL Status Flag
(Figure 32-30). If the user writes the SSPxBUF when a Stop sequence
is in progress, then the WCOL bit is set and the
32.6.8.1 WCOL Status Flag contents of the buffer are unchanged (the write does
If the user writes the SSPxBUF when an Acknowledge not occur).
sequence is in progress, then WCOL bit is set and the
contents of the buffer are unchanged (the write does
not occur).
FIGURE 32-30: ACKNOWLEDGE SEQUENCE WAVEFORM
Acknowledge sequence starts here, ACKEN automatically cleared
write to SSPxCON2
ACKEN = 1, ACKDT = 0
TBRG TBRG
SDA D0 ACK

SCL 8 9

SSPxIF

Cleared in
SSPxIF set at software
the end of receive Cleared in
software SSPxIF set at the end
of Acknowledge sequence
Note: TBRG = one Baud Rate Generator period.

FIGURE 32-31: STOP CONDITION RECEIVE OR TRANSMIT MODE


Write to SSPxCON2, SCL = 1 for TBRG, followed by SDA = 1 for TBRG
set PEN after SDA sampled high. P bit (SSPxSTAT<4>) is set.

Falling edge of PEN bit (SSPxCON2<2>) is cleared by


9th clock hardware and the SSPxIF bit is set
TBRG
SCL

SDA ACK

P
TBRG TBRG TBRG
SCL brought high after TBRG
SDA asserted low before rising edge of clock
to setup Stop condition

Note: TBRG = one Baud Rate Generator period.

 2016-2018 Microchip Technology Inc. DS40001866B-page 455


PIC16(L)F15356/75/76/85/86
32.6.10 SLEEP OPERATION 32.6.13 MULTI -MASTER COMMUNICATION,
2
While in Sleep mode, the I C slave module can receive BUS COLLISION AND BUS
addresses or data and when an address match or ARBITRATION
complete byte transfer occurs, wake the processor Multi-Master mode support is achieved by bus arbitra-
from Sleep (if the MSSP interrupt is enabled). tion. When the master outputs address/data bits onto
the SDA pin, arbitration takes place when the master
32.6.11 EFFECTS OF A RESET outputs a ‘1’ on SDA, by letting SDA float high and
A Reset disables the MSSP module and terminates the another master asserts a ‘0’. When the SCL pin floats
current transfer. high, data should be stable. If the expected data on
SDA is a ‘1’ and the data sampled on the SDA pin is ‘0’,
32.6.12 MULTI-MASTER MODE then a bus collision has taken place. The master will set
In Multi-Master mode, the interrupt generation on the the Bus Collision Interrupt Flag, BCL1IF and reset the
detection of the Start and Stop conditions allows the I2C port to its Idle state (Figure 32-32).
determination of when the bus is free. The Stop (P) and If a transmit was in progress when the bus collision
Start (S) bits are cleared from a Reset or when the occurred, the transmission is halted, the BF flag is
MSSP module is disabled. Control of the I 2C bus may cleared, the SDA and SCL lines are deasserted and the
be taken when the P bit of the SSPxSTAT register is SSPxBUF can be written to. When the user services
set, or the bus is Idle, with both the S and P bits clear. the bus collision Interrupt Service Routine and if the I2C
When the bus is busy, enabling the SSP interrupt will bus is free, the user can resume communication by
generate the interrupt when the Stop condition occurs. asserting a Start condition.
In multi-master operation, the SDA line must be If a Start, Repeated Start, Stop or Acknowledge
monitored for arbitration to see if the signal level is the condition was in progress when the bus collision
expected output level. This check is performed by occurred, the condition is aborted, the SDA and SCL
hardware with the result placed in the BCL1IF bit. lines are deasserted and the respective control bits in
The states where arbitration can be lost are: the SSPxCON2 register are cleared. When the user
services the bus collision Interrupt Service Routine and
• Address Transfer if the I2C bus is free, the user can resume
• Data Transfer communication by asserting a Start condition.
• A Start Condition The master will continue to monitor the SDA and SCL
• A Repeated Start Condition pins. If a Stop condition occurs, the SSPxIF bit will be set.
• An Acknowledge Condition A write to the SSPxBUF will start the transmission of
data at the first data bit, regardless of where the
transmitter left off when the bus collision occurred.
In Multi-Master mode, the interrupt generation on the
detection of Start and Stop conditions allows the
determination of when the bus is free. Control of the I2C
bus can be taken when the P bit is set in the SSPxSTAT
register, or the bus is Idle and the S and P bits are
cleared.

FIGURE 32-32: BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE


Sample SDA. While SCL is high,
Data changes SDA line pulled low data does not match what is driven
while SCL = 0 by another source by the master.
Bus collision has occurred.
SDA released
by master

SDA

SCL Set bus collision


interrupt (BCL1IF)

BCL1IF

 2016-2018 Microchip Technology Inc. DS40001866B-page 456


PIC16(L)F15356/75/76/85/86
32.6.13.1 Bus Collision During a Start If the SDA pin is sampled low during this count, the
Condition BRG is reset and the SDA line is asserted early
(Figure 32-35). If, however, a ‘1’ is sampled on the SDA
During a Start condition, a bus collision occurs if:
pin, the SDA pin is asserted low at the end of the BRG
a) SDA or SCL are sampled low at the beginning of count. The Baud Rate Generator is then reloaded and
the Start condition (Figure 32-33). counts down to zero; if the SCL pin is sampled as ‘0’
b) SCL is sampled low before SDA is asserted low during this time, a bus collision does not occur. At the
(Figure 32-34). end of the BRG count, the SCL pin is asserted low.
During a Start condition, both the SDA and the SCL Note: The reason that bus collision is not a
pins are monitored. factor during a Start condition is that no
If the SDA pin is already low, or the SCL pin is already two bus masters can assert a Start condi-
low, then all of the following occur: tion at the exact same time. Therefore,
one master will always assert SDA before
• the Start condition is aborted,
the other. This condition does not cause a
• the BCL1IF flag is set and bus collision because the two masters
• the MSSP module is reset to its Idle state must be allowed to arbitrate the first
(Figure 32-33). address following the Start condition. If the
The Start condition begins with the SDA and SCL pins address is the same, arbitration must be
deasserted. When the SDA pin is sampled high, the allowed to continue into the data portion,
Baud Rate Generator is loaded and counts down. If the Repeated Start or Stop conditions.
SCL pin is sampled low while SDA is high, a bus
collision occurs because it is assumed that another
master is attempting to drive a data ‘1’ during the Start
condition.

FIGURE 32-33: BUS COLLISION DURING START CONDITION (SDA ONLY)


SDA goes low before the SEN bit is set.
Set BCL1IF,
S bit and SSPxIF set because
SDA = 0, SCL = 1.

SDA

SCL
Set SEN, enable Start SEN cleared automatically because of bus collision.
condition if SDA = 1, SCL = 1 SSP module reset into Idle state.
SEN
SDA sampled low before
Start condition. Set BCL1IF.
S bit and SSPxIF set because
BCL1IF SDA = 0, SCL = 1.
SSPxIF and BCL1IF are
cleared by software

SSPxIF

SSPxIF and BCL1IF are


cleared by software

 2016-2018 Microchip Technology Inc. DS40001866B-page 457


PIC16(L)F15356/75/76/85/86
FIGURE 32-34: BUS COLLISION DURING START CONDITION (SCL = 0)
SDA = 0, SCL = 1

TBRG TBRG

SDA

SCL Set SEN, enable Start


sequence if SDA = 1, SCL = 1
SCL = 0 before SDA = 0,
bus collision occurs. Set BCL1IF.
SEN
SCL = 0 before BRG time-out,
bus collision occurs. Set BCL1IF.
BCL1IF
Interrupt cleared
by software
S ’0’ ’0’

SSPxIF ’0’ ’0’

FIGURE 32-35: BRG RESET DUE TO SDA ARBITRATION DURING START CONDITION
SDA = 0, SCL = 1
Set S Set SSPxIF
Less than TBRG
TBRG

SDA SDA pulled low by other master.


Reset BRG and assert SDA.

SCL S
SCL pulled low after BRG
time-out
SEN
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
BCL1IF ’0’

SSPxIF
SDA = 0, SCL = 1, Interrupts cleared
set SSPxIF by software

 2016-2018 Microchip Technology Inc. DS40001866B-page 458


PIC16(L)F15356/75/76/85/86
32.6.13.2 Bus Collision During a Repeated counting. If SDA goes from high-to-low before the BRG
Start Condition times out, no bus collision occurs because no two
masters can assert SDA at exactly the same time.
During a Repeated Start condition, a bus collision
occurs if: If SCL goes from high-to-low before the BRG times out
and SDA has not already been asserted, a bus collision
a) A low level is sampled on SDA when SCL goes
occurs. In this case, another master is attempting to
from low level to high level (Case 1).
transmit a data ‘1’ during the Repeated Start condition,
b) SCL goes low before SDA is asserted low, see Figure 32-37.
indicating that another master is attempting to
transmit a data ‘1’ (Case 2). If, at the end of the BRG time-out, both SCL and SDA
are still high, the SDA pin is driven low and the BRG is
When the user releases SDA and the pin is allowed to reloaded and begins counting. At the end of the count,
float high, the BRG is loaded with SSPxADD and regardless of the status of the SCL pin, the SCL pin is
counts down to zero. The SCL pin is then deasserted driven low and the Repeated Start condition is
and when sampled high, the SDA pin is sampled. complete.
If SDA is low, a bus collision has occurred (i.e., another
master is attempting to transmit a data ‘0’, Figure 32-36).
If SDA is sampled high, the BRG is reloaded and begins

FIGURE 32-36: BUS COLLISION DURING A REPEATED START CONDITION (CASE 1)

SDA

SCL

Sample SDA when SCL goes high.


If SDA = 0, set BCL1IF and release SDA and SCL.

RSEN

BCL1IF

Cleared by software
S ’0’

SSPxIF ’0’

FIGURE 32-37: BUS COLLISION DURING REPEATED START CONDITION (CASE 2)

TBRG TBRG

SDA

SCL

SCL goes low before SDA,


BCL1IF set BCL1IF. Release SDA and SCL.
Interrupt cleared
by software
RSEN

S ’0’

SSPxIF

 2016-2018 Microchip Technology Inc. DS40001866B-page 459


PIC16(L)F15356/75/76/85/86
32.6.13.3 Bus Collision During a Stop The Stop condition begins with SDA asserted low.
Condition When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
Bus collision occurs during a Stop condition if:
the Baud Rate Generator is loaded with SSPxADD and
a) After the SDA pin has been deasserted and counts down to zero. After the BRG times out, SDA is
allowed to float high, SDA is sampled low after sampled. If SDA is sampled low, a bus collision has
the BRG has timed out (Case 1). occurred. This is due to another master attempting to
b) After the SCL pin is deasserted, SCL is sampled drive a data ‘0’ (Figure 32-38). If the SCL pin is sampled
low before SDA goes high (Case 2). low before SDA is allowed to float high, a bus collision
occurs. This is another case of another master
attempting to drive a data ‘0’ (Figure 32-39).

FIGURE 32-38: BUS COLLISION DURING A STOP CONDITION (CASE 1)

TBRG TBRG TBRG SDA sampled


low after TBRG,
set BCL1IF
SDA

SDA asserted low


SCL

PEN

BCL1IF

P ’0’

SSPxIF ’0’

FIGURE 32-39: BUS COLLISION DURING A STOP CONDITION (CASE 2)

TBRG TBRG TBRG

SDA

Assert SDA SCL goes low before SDA goes high,


set BCL1IF
SCL

PEN

BCL1IF

P ’0’

SSPxIF ’0’

 2016-2018 Microchip Technology Inc. DS40001866B-page 460


PIC16(L)F15356/75/76/85/86
32.7 BAUD RATE GENERATOR module clock line. The logic dictating when the reload
signal is asserted depends on the mode the MSSP is
The MSSP module has a Baud Rate Generator avail- being operated in.
able for clock generation in both I2C and SPI Master
Table 32-4 demonstrates clock rates based on
modes. The Baud Rate Generator (BRG) reload value
instruction cycles and the BRG value loaded into
is placed in the SSPxADD register (Register 32-6).
SSPxADD.
When a write occurs to SSPxBUF, the Baud Rate
Generator will automatically begin counting down.
EQUATION 32-1:
Once the given operation is complete, the internal clock
will automatically stop counting and the clock pin will FOSC
FCLOCK = --------------------------------------------------
-
remain in its last state.  SSP1ADD + 1   4 

An internal signal “Reload” in Figure 32-40 triggers the


value from SSPxADD to be loaded into the BRG
counter. This occurs twice for each oscillation of the

FIGURE 32-40: BAUD RATE GENERATOR BLOCK DIAGRAM

SSPM<3:0> SSPxADD<7:0>

SSPM<3:0> Reload Reload


SCL Control

SSPCLK BRG Down Counter FOSC/2

Note: Values of 0x00, 0x01 and 0x02 are not


valid for SSPxADD when used as a Baud
Rate Generator for I2C. This is an
implementation limitation.

TABLE 32-2: MSSP CLOCK RATE W/BRG


FCLOCK
FOSC FCY BRG Value
(2 Rollovers of BRG)
32 MHz 8 MHz 13h 400 kHz
32 MHz 8 MHz 19h 308 kHz
32 MHz 8 MHz 4Fh 100 kHz
16 MHz 4 MHz 09h 400 kHz
16 MHz 4 MHz 0Ch 308 kHz
16 MHz 4 MHz 27h 100 kHz
4 MHz 1 MHz 09h 100 kHz
Note: Refer to the I/O port electrical specifications in Table 37-4 to ensure the system is designed to support IOL
requirements.

 2016-2018 Microchip Technology Inc. DS40001866B-page 461


PIC16(L)F15356/75/76/85/86
32.8 Register Definitions: MSSPx Control
REGISTER 32-1: SSPxSTAT: SSPx STATUS REGISTER
R/W-0/0 R/W-0/0 R/HS/HC-0 R/HS/HC-0 R/HS/HC-0 R/HS/HC-0 R/HS/HC-0 R/HS/HC-0
SMP CKE(1) D/A P(2) S(2) R/W UA BF
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS/HC = Hardware set/clear

bit 7 SMP: SPI Data Input Sample bit


SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode
In I2 C Master or Slave mode:
1 = Slew rate control disabled for Standard Speed mode (100 kHz and 1 MHz)
0 = Slew rate control enabled for High-Speed mode (400 kHz)
bit 6 CKE: SPI Clock Edge Select bit (SPI mode only)(1)
In SPI Master or Slave mode:
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
In I2 C mode only:
1 = Enable input logic so that thresholds are compliant with SMBus specification
0 = Disable SMBus specific inputs
bit 5 D/A: Data/Address bit (I2C mode only)
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
bit 4 P: Stop bit(2)
(I2C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
1 = Indicates that a Stop bit has been detected last (this bit is ‘0’ on Reset)
0 = Stop bit was not detected last
bit 3 S: Start bit (2)
(I2C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
1 = Indicates that a Start bit has been detected last (this bit is ‘0’ on Reset)
0 = Start bit was not detected last
bit 2 R/W: Read/Write bit information (I2C mode only)
This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the
next Start bit, Stop bit, or not ACK bit.
In I2 C Slave mode:
1 = Read
0 = Write
In I2 C Master mode:
1 = Transmit is in progress
0 = Transmit is not in progress
OR-ing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is in IDLE mode.
bit 1 UA: Update Address bit (10-bit I2C mode only)
1 = Indicates that the user needs to update the address in the SSPxADD register
0 = Address does not need to be updated
bit 0 BF: Buffer Full Status bit
Receive (SPI and I2 C modes):
1 = Receive complete, SSPxBUF is full
0 = Receive not complete, SSPxBUF is empty
Transmit (I2 C mode only):
1 = Data transmit in progress (does not include the ACK and Stop bits), SSPxBUF is full
0 = Data transmit complete (does not include the ACK and Stop bits), SSPxBUF is empty
Note 1: Polarity of clock state is set by the CKP bit of the SSPxCON register.
2: This bit is cleared on Reset and when SSPEN is cleared.

 2016-2018 Microchip Technology Inc. DS40001866B-page 462


PIC16(L)F15356/75/76/85/86

REGISTER 32-2: SSPxCON1: SSPx CONTROL REGISTER 1


R/C/HS-0/0 R/C/HS-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WCOL SSPOV(1) SSPEN CKP SSPM<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS = Bit is set by hardware C = User cleared

bit 7 WCOL: Write Collision Detect bit (Transmit mode only)


1 = The SSPxBUF register is written while it is still transmitting the previous word (must be cleared in software)
0 = No collision
bit 6 SSPOV: Receive Overflow Indicator bit(1)
In SPI mode:
1 = A new byte is received while the SSPxBUF register is still holding the previous data. In case of overflow, the data in SSPxSR is lost.
Overflow can only occur in Slave mode. In Slave mode, the user must read the SSPxBUF, even if only transmitting data, to avoid
setting overflow. In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the
SSPxBUF register (must be cleared in software).
0 = No overflow
In I2 C mode:
1 = A byte is received while the SSPxBUF register is still holding the previous byte. SSPOV is a “don’t care” in Transmit mode
(must be cleared in software).
0 = No overflow
bit 5 SSPEN: Synchronous Serial Port Enable bit
In both modes, when enabled, the following pins must be properly configured as input or output
In SPI mode:
1 = Enables serial port and configures SCK, SDO, SDI and SS as the source of the serial port pins(2)
0 = Disables serial port and configures these pins as I/O port pins
In I2 C mode:
1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins(3)
0 = Disables serial port and configures these pins as I/O port pins
bit 4 CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I2 C Slave mode:
SCL release control
1 = Enable clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
In I2 C Master mode:
Unused in this mode
bit 3-0 SSPM<3:0>: Synchronous Serial Port Mode Select bits
1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1101 = Reserved
1100 = Reserved
1011 = I2C firmware controlled Master mode (slave idle)
1010 = SPI Master mode, clock = FOSC/(4 * (SSPxADD+1))(5)
1001 = Reserved
1000 = I2C Master mode, clock = FOSC / (4 * (SSPxADD+1))(4)
0111 = I2C Slave mode, 10-bit address
0110 = I2C Slave mode, 7-bit address
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0011 = SPI Master mode, clock = T2_match/2
0010 = SPI Master mode, clock = FOSC/64
0001 = SPI Master mode, clock = FOSC/16
0000 = SPI Master mode, clock = FOSC/4
Note 1: In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPxBUF register.
2: When enabled, these pins must be properly configured as input or output. Use SSPxSSPPS, SSPxCLKPPS, SSPxDATPPS, and
RxyPPS to select the pins.
3: When enabled, the SDA and SCL pins must be configured as inputs. Use SSPxCLKPPS, SSPxDATPPS, and RxyPPS to select the pins.
4: SSPxADD values of 0, 1 or 2 are not supported for I2C mode.
5: SSPxADD value of ‘0’ is not supported. Use SSPM = 0000 instead.

 2016-2018 Microchip Technology Inc. DS40001866B-page 463


PIC16(L)F15356/75/76/85/86

REGISTER 32-3: SSPxCON2: SSPx CONTROL REGISTER 2 (I2C MODE ONLY)(1)


R/W-0/0 R/HS/HC-0 R/W-0/0 R/S/HC-0/0 R/S/HC-0/0 R/S/HC-0/0 R/S/HC-0/0 R/S/HC-0/0
GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Cleared by hardware S = User set

bit 7 GCEN: General Call Enable bit (in I2C Slave mode only)
1 = Enable interrupt when a general call address (0x00 or 00h) is received in the SSPxSR
0 = General call address disabled
bit 6 ACKSTAT: Acknowledge Status bit (in I2C mode only)
1 = Acknowledge was not received
0 = Acknowledge was received
bit 5 ACKDT: Acknowledge Data bit (in I2C mode only)
In Receive mode:
Value transmitted when the user initiates an Acknowledge sequence at the end of a receive
1 = Not Acknowledge
0 = Acknowledge
bit 4 ACKEN: Acknowledge Sequence Enable bit (in I2C Master mode only)
In Master Receive mode:
1 = Initiate Acknowledge sequence on SDA and SCL pins, and transmit ACKDT data bit.
Automatically cleared by hardware.
0 = Acknowledge sequence idle
bit 3 RCEN: Receive Enable bit (in I2C Master mode only)
1 = Enables Receive mode for I2C
0 = Receive idle
bit 2 PEN: Stop Condition Enable bit (in I2C Master mode only)
SCKMSSP Release Control:
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
bit 1 RSEN: Repeated Start Condition Enable bit (in I2C Master mode only)
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
bit 0 SEN: Start Condition Enable/Stretch Enable bit
In Master mode:
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
In Slave mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled

Note 1: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the IDLE mode, this bit may not be
set (no spooling) and the SSPxBUF may not be written (or writes to the SSPxBUF are disabled).

 2016-2018 Microchip Technology Inc. DS40001866B-page 464


PIC16(L)F15356/75/76/85/86

REGISTER 32-4: SSPxCON3: SSPx CONTROL REGISTER 3


R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ACKTIM(3) PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 ACKTIM: Acknowledge Time Status bit (I2C mode only)(3)


1 = Indicates the I2C bus is in an Acknowledge sequence, set on 8th falling edge of SCL clock
0 = Not an Acknowledge sequence, cleared on 9TH rising edge of SCL clock
bit 6 PCIE: Stop Condition Interrupt Enable bit (I2C mode only)
1 = Enable interrupt on detection of Stop condition
0 = Stop detection interrupts are disabled(2)
bit 5 SCIE: Start Condition Interrupt Enable bit (I2C mode only)
1 = Enable interrupt on detection of Start or Restart conditions
0 = Start detection interrupts are disabled(2)
bit 4 BOEN: Buffer Overwrite Enable bit
In SPI Slave mode:(1)
1 = SSPxBUF updates every time that a new data byte is shifted in ignoring the BF bit
0 = If new byte is received with BF bit of the SSPxSTAT register already set, SSPOV bit of the SSPxCON1
register is set, and the buffer is not updated
In I2 C Master mode and SPI Master mode:
This bit is ignored.
In I2 C Slave mode:
1 = SSPxBUF is updated and ACK is generated for a received address/data byte, ignoring the state of the
SSPOV bit only if the BF bit = 0.
0 = SSPxBUF is only updated when SSPOV is clear
bit 3 SDAHT: SDA Hold Time Selection bit (I2C mode only)
1 = Minimum of 300 ns hold time on SDA after the falling edge of SCL
0 = Minimum of 100 ns hold time on SDA after the falling edge of SCL
bit 2 SBCDE: Slave Mode Bus Collision Detect Enable bit (I2C Slave mode only)
If, on the rising edge of SCL, SDA is sampled low when the module is outputting a high state, the BCL1IF bit of the
PIR3 register is set, and bus goes idle
1 = Enable slave bus collision interrupts
0 = Slave bus collision interrupts are disabled
bit 1 AHEN: Address Hold Enable bit (I2C Slave mode only)
1 = Following the eighth falling edge of SCL for a matching received address byte; CKP bit of the SSPxCON1
register will be cleared and the SCL will be held low.
0 = Address holding is disabled
bit 0 DHEN: Data Hold Enable bit (I2C Slave mode only)
1 = Following the eighth falling edge of SCL for a received data byte; slave hardware clears the CKP bit of the
SSPxCON1 register and SCL is held low.
0 = Data holding is disabled

Note 1: For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPOV is still set when a new
byte is received and BF = 1, but hardware continues to write the most recent byte to SSPxBUF.
2: This bit has no effect in Slave modes that Start and Stop condition detection is explicitly listed as enabled.
3: The ACKTIM Status bit is only active when the AHEN bit or DHEN bit is set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 465


PIC16(L)F15356/75/76/85/86

REGISTER 32-5: SSPxMSK: SSPx MASK REGISTER


R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
SSPxMSK<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-1 SSPxMSK<7:1>: Mask bits


1 = The received address bit n is compared to SSPxADD<n> to detect I2C address match
0 = The received address bit n is not used to detect I2C address match
bit 0 SSPxMSK<0>: Mask bit for I2C Slave mode, 10-bit Address
I2C Slave mode, 10-bit address (SSPM<3:0> = 0111 or 1111):
1 = The received address bit 0 is compared to SSPxADD<0> to detect I2C address match
0 = The received address bit 0 is not used to detect I2C address match
I2C Slave mode, 7-bit address:
MSK0 bit is ignored.

REGISTER 32-6: SSPxADD: MSSPx ADDRESS AND BAUD RATE REGISTER (I2C MODE)
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
SSPxADD<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

Master mode:

bit 7-0 SSPxADD<7:0>: Baud Rate Clock Divider bits


SCL pin clock period = ((ADD<7:0> + 1) *4)/FOSC
10-Bit Slave mode – Most Significant Address Byte:

bit 7-3 Not used: Unused for Most Significant Address Byte. Bit state of this register is a “don’t care”. Bit
pattern sent by master is fixed by I2C specification and must be equal to ‘11110’. However, those bits
are compared by hardware and are not affected by the value in this register.
bit 2-1 SSPxADD<2:1>: Two Most Significant bits of 10-bit address
bit 0 Not used: Unused in this mode. Bit state is a “don’t care”.
10-Bit Slave mode – Least Significant Address Byte:

bit 7-0 SSPxADD<7:0>: Eight Least Significant bits of 10-bit address


7-Bit Slave mode:

bit 7-1 SSPxADD<7:1>: 7-bit address


bit 0 Not used: Unused in this mode. Bit state is a “don’t care”.

 2016-2018 Microchip Technology Inc. DS40001866B-page 466


PIC16(L)F15356/75/76/85/86
REGISTER 32-7: SSPxBUF: MSSPx BUFFER REGISTER
R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x
SSPxBUF<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SSPxBUF<7:0>: MSSP Buffer bits

TABLE 32-3: SUMMARY OF REGISTERS ASSOCIATED WITH MSSPx


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE — — — — — INTEDG 147


PIR3 RC2IF TX2IF RC1IF TX1IF BCL2IF SSP2IF BCL1IF SSP1IF 141
PIE3 RC2IE TX2IE RC1IE TX1IE BCL2IE SSP2IE BCL1IE SSP1IE 133
SSP1STAT SMP CKE D/A P S R/W UA BF 462
SSP1CON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 463
SSP1CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 464
SSP1CON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 462
SSP1MSK SSPMSK<7:0> 466
SSP1ADD SSPADD<7:0> 466
SSP1BUF SSPBUF<7:0> 467
SSP2STAT SMP CKE D/A P S R/W UA BF 462
SSP2CON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 463
SSP2CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 464
SSP2CON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 462
SSP2MSK SSPMSK<7:0> 466
SSP2ADD SSPADD<7:0> 466
SSP2BUF SSPBUF<7:0> 467
SSP1CLKPPS — — SSP1CLKPPS<5:0> 242
SSP1DATPPS — — SSP1DATPPS<5:0> 242
SSP1SSPPS — — SSP1SSPPS<5:0> 242
SSP2CLKPPS — — SSP2CLKPPS<5:0> 242
SSP2DATPPS — — SSP2DATPPS<5:0> 242
SSP2SSPPS — — SSP2SSPPS<5:0> 242
RxyPPS — — RxyPPS<4:0> 243
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the MSSPx module
Note 1: When using designated I2C pins, the associated pin values in INLVLx will be ignored.

 2016-2018 Microchip Technology Inc. DS40001866B-page 467


PIC16(L)F15356/75/76/85/86
33.0 ENHANCED UNIVERSAL The EUSART module includes the following capabilities:
SYNCHRONOUS • Full-duplex asynchronous transmit and receive
ASYNCHRONOUS RECEIVER • Two-character input buffer
TRANSMITTER (EUSART) • One-character output buffer
• Programmable 8-bit or 9-bit character length
The Enhanced Universal Synchronous Asynchronous
• Address detection in 9-bit mode
Receiver Transmitter (EUSART) module is a serial I/O
communications peripheral. It contains all the clock • Input buffer overrun error detection
generators, shift registers and data buffers necessary • Received character framing error detection
to perform an input or output serial data transfer • Half-duplex synchronous master
independent of device program execution. The • Half-duplex synchronous slave
EUSART, also known as a Serial Communications • Programmable clock polarity in synchronous
Interface (SCI), can be configured as a full-duplex modes
asynchronous system or half-duplex synchronous
• Sleep operation
system. Full-Duplex mode is useful for
communications with peripheral systems, such as CRT The EUSART module implements the following
terminals and personal computers. Half-Duplex additional features, making it ideally suited for use in
Synchronous mode is intended for communications Local Interconnect Network (LIN) bus systems:
with peripheral devices, such as A/D or D/A integrated • Automatic detection and calibration of the baud rate
circuits, serial EEPROMs or other microcontrollers.
• Wake-up on Break reception
These devices typically do not have internal clocks for
baud rate generation and require the external clock • 13-bit Break character transmit
signal provided by a master synchronous device. Block diagrams of the EUSART transmitter and
receiver are shown in Figure 33-1 and Figure 33-2.
Note: Two identical EUSART modules are
implemented on this device, EUSART1 The EUSART transmit output (TX_out) is available to
and EUSART2. All references to the TX/CK pin and internally to the following peripherals:
EUSART1 apply to EUSART2 as well. • Configurable Logic Cell (CLC)

FIGURE 33-1: EUSART TRANSMIT BLOCK DIAGRAM

Data Bus
TXxIE
SYNC
Interrupt
CSRC
TXxREG Register TXxIF
8 RxyPPS(1)
CK pin TXEN
MSb LSb RX/DT pin
PPS 1 (8) 0 Pin Buffer
• • • and Control PPS
0 Transmit Shift Register (TSR)
CKPPS SYNC

TRMT TX_out
Baud Rate Generator FOSC
÷n
TX9
BRG16 n
+1 Multiplier x4 x16 x64
TX9D TX/CK pin
SYNC 1 X 0 0 0 0
PPS
SPxBRGH SPxBRGL BRGH X 1 1 0 0
1
BRG16 X 1 0 1 0
RxyPPS
SYNC
Note 1: In Synchronous mode the DT output and RX input PPS CSRC
selections should enable the same pin.

 2016-2018 Microchip Technology Inc. DS40001866B-page 468


PIC16(L)F15356/75/76/85/86
FIGURE 33-2: EUSART RECEIVE BLOCK DIAGRAM

SPEN CREN OERR RCIDL

RXPPS(1)
RX/DT pin MSb RSR Register LSb
Pin Buffer Data
PPS and Control Recovery
Stop (8) 7 ••• 1 0 Start

Baud Rate Generator FOSC RX9


÷n

BRG16
+1 n
Multiplier x4 x16 x64
SYNC 1 X 0 0 0
SPxBRGH SPxBRGL BRGH X 1 1 0 0 FIFO
FERR RX9D RCxREG Register
BRG16 X 1 0 1 0
8
Data Bus

Note 1: In Synchronous mode the DT output and RX input PPS RXxIF Interrupt
selections should enable the same pin. RXxIE

The operation of the EUSART module is controlled


through three registers:
• Transmit Status and Control (TXxSTA)
• Receive Status and Control (RCxSTA)
• Baud Rate Control (BAUDxCON)
These registers are detailed in Register 33-1,
Register 33-2 and Register 33-3, respectively.
The RX input pin is selected with the RXxPPS. The CK
input is selected with the TXxPPS register. TX, CK, and
DT output pins are selected with each pin’s RxyPPS
register. Since the RX input is coupled with the DT output
in Synchronous mode, it is the user’s responsibility to
select the same pin for both of these functions when
operating in Synchronous mode. The EUSART control
logic will control the data direction drivers automatically.

 2016-2018 Microchip Technology Inc. DS40001866B-page 469


PIC16(L)F15356/75/76/85/86
33.1 EUSART Asynchronous Mode 33.1.1.2 Transmitting Data
The EUSART transmits and receives data using the A transmission is initiated by writing a character to the
standard non-return-to-zero (NRZ) format. NRZ is TXxREG register. If this is the first character, or the
implemented with two levels: a VOH Mark state which previous character has been completely flushed from
represents a ‘1’ data bit, and a VOL Space state which the TSR, the data in the TXxREG is immediately
represents a ‘0’ data bit. NRZ refers to the fact that transferred to the TSR register. If the TSR still contains
consecutively transmitted data bits of the same value all or part of a previous character, the new character
stay at the output level of that bit without returning to a data is held in the TXxREG until the Stop bit of the
neutral level between each bit transmission. An NRZ previous character has been transmitted. The pending
transmission port idles in the Mark state. Each character character in the TXxREG is then transferred to the TSR
transmission consists of one Start bit followed by eight in one TCY immediately following the Stop bit
or nine data bits and is always terminated by one or transmission. The transmission of the Start bit, data bits
more Stop bits. The Start bit is always a space and the and Stop bit sequence commences immediately
Stop bits are always marks. The most common data following the transfer of the data to the TSR from the
format is eight bits. Each transmitted bit persists for a TXxREG.
period of 1/(Baud Rate). An on-chip dedicated 8-bit/16-
bit Baud Rate Generator is used to derive standard 33.1.1.3 Transmit Data Polarity
baud rate frequencies from the system oscillator. See The polarity of the transmit data can be controlled with
Table 33-3 for examples of baud rate configurations. the SCKP bit of the BAUDxCON register. The default
The EUSART transmits and receives the LSb first. The state of this bit is ‘0’ which selects high true transmit idle
EUSART’s transmitter and receiver are functionally and data bits. Setting the SCKP bit to ‘1’ will invert the
independent, but share the same data format and baud transmit data resulting in low true idle and data bits. The
rate. Parity is not supported by the hardware, but can SCKP bit controls transmit data polarity in
be implemented in software and stored as the ninth Asynchronous mode only. In Synchronous mode, the
data bit. SCKP bit has a different function. See Section 33.4.1.2
“Clock Polarity”.
33.1.1 EUSART ASYNCHRONOUS
TRANSMITTER 33.1.1.4 Transmit Interrupt Flag
The TXxIF interrupt flag bit of the PIR3 register is set
The EUSART transmitter block diagram is shown in
whenever the EUSART transmitter is enabled and no
Figure 33-1. The heart of the transmitter is the serial
character is being held for transmission in the TXxREG.
Transmit Shift Register (TSR), which is not directly
In other words, the TXxIF bit is only clear when the TSR
accessible by software. The TSR obtains its data from
is busy with a character and a new character has been
the transmit buffer, which is the TXxREG register.
queued for transmission in the TXxREG. The TXxIF flag
33.1.1.1 Enabling the Transmitter bit is not cleared immediately upon writing TXxREG.
TXxIF becomes valid in the second instruction cycle
The EUSART transmitter is enabled for asynchronous following the write execution. Polling TXxIF immediately
operations by configuring the following three control following the TXxREG write will return invalid results.
bits: The TXxIF bit is read-only, it cannot be set or cleared by
• TXEN = 1 software.
• SYNC = 0 The TXxIF interrupt can be enabled by setting the
• SPEN = 1 TXxIE interrupt enable bit of the PIE3 register. How-
ever, the TXxIF flag bit will be set whenever the
All other EUSART control bits are assumed to be in
TXxREG is empty, regardless of the state of TXxIE
their default state.
enable bit.
Setting the TXEN bit of the TXxSTA register enables the
To use interrupts when transmitting data, set the TXxIE
transmitter circuitry of the EUSART. Clearing the SYNC
bit only when there is more data to send. Clear the
bit of the TXxSTA register configures the EUSART for
TXxIE interrupt enable bit upon writing the last charac-
asynchronous operation. Setting the SPEN bit of the
ter of the transmission to the TXxREG.
RCxSTA register enables the EUSART and
automatically configures the TX/CK I/O pin as an output.
If the TX/CK pin is shared with an analog peripheral, the
analog I/O function must be disabled by clearing the
corresponding ANSEL bit.
Note: The TXxIF Transmitter Interrupt flag is set
when the TXEN enable bit is set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 470


PIC16(L)F15356/75/76/85/86
33.1.1.5 TSR Status 33.1.1.7 Asynchronous Transmission Set-up:
The TRMT bit of the TXxSTA register indicates the 1. Initialize the SPxBRGH, SPxBRGL register pair
status of the TSR register. This is a read-only bit. The and the BRGH and BRG16 bits to achieve the
TRMT bit is set when the TSR register is empty and is desired baud rate (see Section 33.3 “EUSART
cleared when a character is transferred to the TSR Baud Rate Generator (BRG)”).
register from the TXxREG. The TRMT bit remains clear 2. Enable the asynchronous serial port by clearing
until all bits have been shifted out of the TSR register. the SYNC bit and setting the SPEN bit.
No interrupt logic is tied to this bit, so the user has to 3. If 9-bit transmission is desired, set the TX9
poll this bit to determine the TSR status. control bit. A set ninth data bit will indicate that
Note: The TSR register is not mapped in data the eight Least Significant data bits are an
memory, so it is not available to the user. address when the receiver is set for address
detection.
33.1.1.6 Transmitting 9-Bit Characters 4. Set SCKP bit if inverted transmit is desired.
The EUSART supports 9-bit character transmissions. 5. Enable the transmission by setting the TXEN
When the TX9 bit of the TXxSTA register is set, the control bit. This will cause the TXxIF interrupt bit
EUSART will shift nine bits out for each character trans- to be set.
mitted. The TX9D bit of the TXxSTA register is the 6. If interrupts are desired, set the TXxIE interrupt
ninth, and Most Significant data bit. When transmitting enable bit of the PIE3 register. An interrupt will
9-bit data, the TX9D data bit must be written before occur immediately provided that the GIE and
writing the eight Least Significant bits into the TXxREG. PEIE bits of the INTCON register are also set.
All nine bits of data will be transferred to the TSR shift 7. If 9-bit transmission is selected, the ninth bit
register immediately after the TXxREG is written. should be loaded into the TX9D data bit.
A special 9-bit Address mode is available for use with 8. Load 8-bit data into the TXxREG register. This
multiple receivers. See Section 33.1.2.7 “Address will start the transmission.
Detection” for more information on the Address mode.

FIGURE 33-3: ASYNCHRONOUS TRANSMISSION

Write to TXxREG
Word 1
BRG Output
(Shift Clock)
TX/CK
pin Start bit bit 0 bit 1 bit 7/8 Stop bit
Word 1
TXxIF bit
(Transmit Buffer 1 TCY
Reg. Empty Flag)

Word 1
TRMT bit Transmit Shift Reg.
(Transmit Shift
Reg. Empty Flag)

 2016-2018 Microchip Technology Inc. DS40001866B-page 471


PIC16(L)F15356/75/76/85/86
FIGURE 33-4: ASYNCHRONOUS TRANSMISSION (BACK-TO-BACK)

Write to TXxREG
Word 1 Word 2
BRG Output
(Shift Clock)
TX/CK
pin Start bit bit 0 bit 1 bit 7/8 Stop bit Start bit bit 0
TXxIF bit 1 TCY Word 1 Word 2
(Transmit Buffer
Reg. Empty Flag) 1 TCY

TRMT bit Word 1 Word 2


(Transmit Shift Transmit Shift Reg. Transmit Shift Reg.
Reg. Empty Flag)

Note: This timing diagram shows two consecutive transmissions.

33.1.2 EUSART ASYNCHRONOUS 33.1.2.2 Receiving Data


RECEIVER The receiver data recovery circuit initiates character
The Asynchronous mode is typically used in RS-232 reception on the falling edge of the first bit. The first bit,
systems. The receiver block diagram is shown in also known as the Start bit, is always a zero. The data
Figure 33-2. The data is received on the RX/DT pin and recovery circuit counts one-half bit time to the center of
drives the data recovery block. The data recovery block the Start bit and verifies that the bit is still a zero. If it is
is actually a high-speed shifter operating at 16 times not a zero then the data recovery circuit aborts
the baud rate, whereas the serial Receive Shift character reception, without generating an error, and
Register (RSR) operates at the bit rate. When all eight resumes looking for the falling edge of the Start bit. If
or nine bits of the character have been shifted in, they the Start bit zero verification succeeds then the data
are immediately transferred to a two character First-In- recovery circuit counts a full bit time to the center of the
First-Out (FIFO) memory. The FIFO buffering allows next bit. The bit is then sampled by a majority detect
reception of two complete characters and the start of a circuit and the resulting ‘0’ or ‘1’ is shifted into the RSR.
third character before software must start servicing the This repeats until all data bits have been sampled and
EUSART receiver. The FIFO and RSR registers are not shifted into the RSR. One final bit time is measured and
directly accessible by software. Access to the received the level sampled. This is the Stop bit, which is always
data is via the RCxREG register. a ‘1’. If the data recovery circuit samples a ‘0’ in the
Stop bit position then a framing error is set for this
33.1.2.1 Enabling the Receiver character, otherwise the framing error is cleared for this
The EUSART receiver is enabled for asynchronous character. See Section 33.1.2.4 “Receive Framing
operation by configuring the following three control bits: Error” for more information on framing errors.

• CREN = 1 Immediately after all data bits and the Stop bit have
been received, the character in the RSR is transferred
• SYNC = 0
to the EUSART receive FIFO and the RXxIF interrupt
• SPEN = 1 flag bit of the PIR3 register is set. The top character in
All other EUSART control bits are assumed to be in the FIFO is transferred out of the FIFO by reading the
their default state. RCxREG register.
Setting the CREN bit of the RCxSTA register enables Note: If the receive FIFO is overrun, no additional
the receiver circuitry of the EUSART. Clearing the SYNC characters will be received until the overrun
bit of the TXxSTA register configures the EUSART for condition is cleared. See Section 33.1.2.5
asynchronous operation. Setting the SPEN bit of the “Receive Overrun Error” for more
RCxSTA register enables the EUSART. The information on overrun errors.
programmer must set the corresponding TRIS bit to
configure the RX/DT I/O pin as an input.
Note: If the RX/DT function is on an analog pin,
the corresponding ANSEL bit must be
cleared for the receiver to function.

 2016-2018 Microchip Technology Inc. DS40001866B-page 472


PIC16(L)F15356/75/76/85/86
33.1.2.3 Receive Interrupts 33.1.2.6 Receiving 9-Bit Characters
The RXxIF interrupt flag bit of the PIR3 register is set The EUSART supports 9-bit character reception. When
whenever the EUSART receiver is enabled and there is the RX9 bit of the RCxSTA register is set the EUSART
an unread character in the receive FIFO. The RXxIF will shift nine bits into the RSR for each character
interrupt flag bit is read-only, it cannot be set or cleared received. The RX9D bit of the RCxSTA register is the
by software. ninth and Most Significant data bit of the top unread
RXxIF interrupts are enabled by setting all of the character in the receive FIFO. When reading 9-bit data
following bits: from the receive FIFO buffer, the RX9D data bit must
be read before reading the eight Least Significant bits
• RXxIE, Interrupt Enable bit of the PIE3 register from the RCxREG.
• PEIE, Peripheral Interrupt Enable bit of the
INTCON register 33.1.2.7 Address Detection
• GIE, Global Interrupt Enable bit of the INTCON A special Address Detection mode is available for use
register when multiple receivers share the same transmission
The RXxIF interrupt flag bit will be set when there is an line, such as in RS-485 systems. Address detection is
unread character in the FIFO, regardless of the state of enabled by setting the ADDEN bit of the RCxSTA
interrupt enable bits. register.
Address detection requires 9-bit character reception.
33.1.2.4 Receive Framing Error When address detection is enabled, only characters
Each character in the receive FIFO buffer has a with the ninth data bit set will be transferred to the
corresponding framing error Status bit. A framing error receive FIFO buffer, thereby setting the RXxIF interrupt
indicates that a Stop bit was not seen at the expected bit. All other characters will be ignored.
time. The framing error status is accessed via the Upon receiving an address character, user software
FERR bit of the RCxSTA register. The FERR bit determines if the address matches its own. Upon
represents the status of the top unread character in the address match, user software must disable address
receive FIFO. Therefore, the FERR bit must be read detection by clearing the ADDEN bit before the next
before reading the RCxREG. Stop bit occurs. When user software detects the end of
The FERR bit is read-only and only applies to the top the message, determined by the message protocol
unread character in the receive FIFO. A framing error used, software places the receiver back into the
(FERR = 1) does not preclude reception of additional Address Detection mode by setting the ADDEN bit.
characters. It is not necessary to clear the FERR bit.
Reading the next character from the FIFO buffer will
advance the FIFO to the next character and the next
corresponding framing error.
The FERR bit can be forced clear by clearing the SPEN
bit of the RCxSTA register which resets the EUSART.
Clearing the CREN bit of the RCxSTA register does not
affect the FERR bit. A framing error by itself does not
generate an interrupt.
Note: If all receive characters in the receive
FIFO have framing errors, repeated reads
of the RCxREG will not clear the FERR bit.

33.1.2.5 Receive Overrun Error


The receive FIFO buffer can hold two characters. An
overrun error will be generated if a third character, in its
entirety, is received before the FIFO is accessed. When
this happens the OERR bit of the RCxSTA register is
set. The characters already in the FIFO buffer can be
read but no additional characters will be received until
the error is cleared. The error must be cleared by either
clearing the CREN bit of the RCxSTA register or by
resetting the EUSART by clearing the SPEN bit of the
RCxSTA register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 473


PIC16(L)F15356/75/76/85/86
33.1.2.8 Asynchronous Reception Setup: 33.1.2.9 9-bit Address Detection Mode Setup
1. Initialize the SPxBRGH, SPxBRGL register pair This mode would typically be used in RS-485 systems.
and the BRGH and BRG16 bits to achieve the To set up an Asynchronous Reception with Address
desired baud rate (see Section 33.3 “EUSART Detect Enable:
Baud Rate Generator (BRG)”). 1. Initialize the SPxBRGH, SPxBRGL register pair
2. Clear the ANSEL bit for the RX pin (if applicable). and the BRGH and BRG16 bits to achieve the
3. Enable the serial port by setting the SPEN bit. desired baud rate (see Section 33.3 “EUSART
The SYNC bit must be clear for asynchronous Baud Rate Generator (BRG)”).
operation. 2. Clear the ANSEL bit for the RX pin (if applicable).
4. If interrupts are desired, set the RXxIE bit of the 3. Enable the serial port by setting the SPEN bit.
PIE3 register and the GIE and PEIE bits of the The SYNC bit must be clear for asynchronous
INTCON register. operation.
5. If 9-bit reception is desired, set the RX9 bit. 4. If interrupts are desired, set the RXxIE bit of the
6. Enable reception by setting the CREN bit. PIE3 register and the GIE and PEIE bits of the
7. The RXxIF interrupt flag bit will be set when a INTCON register.
character is transferred from the RSR to the 5. Enable 9-bit reception by setting the RX9 bit.
receive buffer. An interrupt will be generated if 6. Enable address detection by setting the ADDEN
the RXxIE interrupt enable bit was also set. bit.
8. Read the RCxSTA register to get the error flags 7. Enable reception by setting the CREN bit.
and, if 9-bit data reception is enabled, the ninth 8. The RXxIF interrupt flag bit will be set when a
data bit. character with the ninth bit set is transferred
9. Get the received eight Least Significant data bits from the RSR to the receive buffer. An interrupt
from the receive buffer by reading the RCxREG will be generated if the RXxIE interrupt enable
register. bit was also set.
10. If an overrun occurred, clear the OERR flag by 9. Read the RCxSTA register to get the error flags.
clearing the CREN receiver enable bit. The ninth data bit will always be set.
10. Get the received eight Least Significant data bits
from the receive buffer by reading the RCxREG
register. Software determines if this is the
device’s address.
11. If an overrun occurred, clear the OERR flag by
clearing the CREN receiver enable bit.
12. If the device has been addressed, clear the
ADDEN bit to allow all received data into the
receive buffer and generate interrupts.

FIGURE 33-5: ASYNCHRONOUS RECEPTION


Start Start Start
RX/DT pin bit bit 0 bit 1 bit 7/8 Stop bit bit 0 bit 7/8 Stop bit bit 7/8 Stop
bit bit bit
Rcv Shift
Reg
Rcv Buffer Reg.
Word 1 Word 2
RCxREG RCxREG
RCIDL

Read Rcv
Buffer Reg.
RCxREG

RXxIF
(Interrupt Flag)

OERR bit
CREN

Note: This timing diagram shows three words appearing on the RX input. The RCxREG (receive buffer) is read after the third word,
causing the OERR (overrun) bit to be set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 474


PIC16(L)F15356/75/76/85/86
33.2 Clock Accuracy with
Asynchronous Operation
The factory calibrates the internal oscillator block
output (INTOSC). However, the HFINTOSC frequency
may drift as VDD or temperature changes, and this
directly affects the asynchronous baud rate. Two
methods may be used to adjust the baud rate clock, but
both require a reference clock source of some kind.
The first (preferred) method uses the OSCTUNE
register to adjust the HFINTOSC output. Adjusting the
value in the OSCTUNE register allows for fine resolution
changes to the system clock source. See
Section 9.2.2.2 “Internal Oscillator Frequency
Adjustment” for more information.
The other method adjusts the value in the Baud Rate
Generator. This can be done automatically with the
Auto-Baud Detect feature (see Section 33.3.1 “Auto-
Baud Detect”). There may not be fine enough
resolution when adjusting the Baud Rate Generator to
compensate for a gradual change in the peripheral
clock frequency.

 2016-2018 Microchip Technology Inc. DS40001866B-page 475


PIC16(L)F15356/75/76/85/86
33.3 EUSART Baud Rate Generator EXAMPLE 33-1: CALCULATING BAUD
(BRG) RATE ERROR
The Baud Rate Generator (BRG) is an 8-bit or 16-bit For a device with FOSC of 16 MHz, desired baud rate
timer that is dedicated to the support of both the of 9600, Asynchronous mode, 8-bit BRG:
asynchronous and synchronous EUSART operation. F OS C
By default, the BRG operates in 8-bit mode. Setting the Desired Baud Rate = -----------------------------------------------------------------------
-
64  [SPBRGH:SPBRGL] + 1 
BRG16 bit of the BAUDxCON register selects 16-bit
mode. Solving for SPxBRGH:SPxBRGL:
The SPxBRGH, SPxBRGL register pair determines the F O SC
---------------------------------------------
period of the free running baud rate timer. In Desired Baud Rate – 1
X = ---------------------------------------------
Asynchronous mode the multiplier of the baud rate 64
period is determined by both the BRGH bit of the 16000000
------------------------
TXxSTA register and the BRG16 bit of the BAUDxCON 9600 - – 1
= -----------------------
register. In Synchronous mode, the BRGH bit is ignored. 64

Table 33-1 contains the formulas for determining the =  25.042  = 25


baud rate. Example 33-1 provides a sample calculation
16000000-
Calculated Baud Rate = --------------------------
for determining the baud rate and baud rate error. 64  25 + 1 
Typical baud rates and error values for various
Asynchronous modes have been computed for your = 9615
convenience and are shown in Table 33-3. It may be
advantageous to use the high baud rate (BRGH = 1), Error = Calc. Baud Rate – Desired Baud Rate-
-------------------------------------------------------------------------------------------
Desired Baud Rate
or the 16-bit BRG (BRG16 = 1) to reduce the baud rate
error. The 16-bit BRG mode is used to achieve slow = ----------------------------------
9615 – 9600  = 0.16%
baud rates for fast oscillator frequencies. 9600

Writing a new value to the SPxBRGH, SPxBRGL


register pair causes the BRG timer to be reset (or
cleared). This ensures that the BRG does not wait for a
timer overflow before outputting the new baud rate.
If the system clock is changed during an active receive
operation, a receive error or data loss may result. To
avoid this problem, check the status of the RCIDL bit to
make sure that the receive operation is idle before
changing the system clock.

 2016-2018 Microchip Technology Inc. DS40001866B-page 476


PIC16(L)F15356/75/76/85/86
33.3.1 AUTO-BAUD DETECT 8th the BRG base clock rate. The resulting byte
measurement is the average bit time when clocked at
The EUSART module supports automatic detection
full speed.
and calibration of the baud rate.
Note 1: If the WUE bit is set with the ABDEN bit,
In the Auto-Baud Detect (ABD) mode, the clock to the
auto-baud detection will occur on the byte
BRG is reversed. Rather than the BRG clocking the
following the Break character (see
incoming RX signal, the RX signal is timing the BRG.
Section 33.3.3 “Auto-Wake-up on
The Baud Rate Generator is used to time the period of
Break”).
a received 55h (ASCII “U”) which is the Sync character
for the LIN bus. The unique feature of this character is 2: It is up to the user to determine that the
that it has five rising edges including the Stop bit edge. incoming character baud rate is within the
range of the selected BRG clock source.
Setting the ABDEN bit of the BAUDxCON register
Some combinations of oscillator frequency
starts the auto-baud calibration sequence. While the
and EUSART baud rates are not possible.
ABD sequence takes place, the EUSART state
machine is held in Idle. On the first rising edge of the 3: During the auto-baud process, the auto-
receive line, after the Start bit, the SPxBRG begins baud counter starts counting at one. Upon
counting up using the BRG counter clock as shown in completion of the auto-baud sequence, to
Figure 33-6. The fifth rising edge will occur on the RX achieve maximum accuracy, subtract 1
pin at the end of the eighth bit period. At that time, an from the SPxBRGH:SPxBRGL register
accumulated value totaling the proper BRG period is pair.
left in the SPxBRGH, SPxBRGL register pair, the
ABDEN bit is automatically cleared and the RXxIF TABLE 33-1: BRG COUNTER CLOCK RATES
interrupt flag is set. The value in the RCxREG needs to
BRG Base BRG ABD
be read to clear the RXxIF interrupt. RCxREG content BRG16 BRGH
Clock Clock
should be discarded. When calibrating for modes that
do not use the SPxBRGH register the user can verify 0 0 FOSC/64 FOSC/512
that the SPxBRGL register did not overflow by
checking for 00h in the SPxBRGH register. 0 1 FOSC/16 FOSC/128

The BRG auto-baud clock is determined by the BRG16 1 0 FOSC/16 FOSC/128


and BRGH bits as shown in Table 33-1. During ABD, 1 1 FOSC/4 FOSC/32
both the SPxBRGH and SPxBRGL registers are used Note: During the ABD sequence, SPxBRGL and
as a 16-bit counter, independent of the BRG16 bit SPxBRGH registers are both used as a 16-
setting. While calibrating the baud rate period, the bit counter, independent of the BRG16
SPxBRGH and SPxBRGL registers are clocked at 1/ setting.

FIGURE 33-6: AUTOMATIC BAUD RATE CALIBRATION

BRG Value XXXXh 0000h 001Ch

Edge #1 Edge #2 Edge #3 Edge #4 Edge #5


RX pin Start bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 Stop bit

BRG Clock

Set by User Auto Cleared


ABDEN bit

RCIDL

RXxIF bit
(Interrupt)

Read
RCxREG

SPxBRGL XXh 1Ch

SPxBRGH XXh 00h

Note 1: The ABD sequence requires the EUSART module to be configured in Asynchronous mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 477


PIC16(L)F15356/75/76/85/86
33.3.2 AUTO-BAUD OVERFLOW 33.3.3.1 Special Considerations
During the course of automatic baud detection, the Break Character
ABDOVF bit of the BAUDxCON register will be set if the To avoid character errors or character fragments during
baud rate counter overflows before the fifth rising edge a wake-up event, the wake-up character must be all
is detected on the RX pin. The ABDOVF bit indicates zeros.
that the counter has exceeded the maximum count that
can fit in the 16 bits of the SPxBRGH:SPxBRGL When the wake-up is enabled the function works
register pair. The overflow condition will set the RXxIF independent of the low time on the data stream. If the
flag. The counter continues to count until the fifth rising WUE bit is set and a valid non-zero character is
edge is detected on the RX pin. The RCIDL bit will received, the low time from the Start bit to the first rising
remain false (‘0’) until the fifth rising edge at which time edge will be interpreted as the wake-up event. The
the RCIDL bit will be set. If the RCxREG is read after remaining bits in the character will be received as a
the overflow occurs but before the fifth rising edge then fragmented character and subsequent characters can
the fifth rising edge will set the RXxIF again. result in framing or overrun errors.

Terminating the auto-baud process early to clear an Therefore, the initial character in the transmission must
overflow condition will prevent proper detection of the be all ‘0’s. This must be ten or more bit times, 13-bit
sync character fifth rising edge. If any falling edges of times recommended for LIN bus, or any number of bit
the sync character have not yet occurred when the times for standard RS-232 devices.
ABDEN bit is cleared then those will be falsely detected Oscillator Start-up Time
as Start bits. The following steps are recommended to
Oscillator start-up time must be considered, especially
clear the overflow condition:
in applications using oscillators with longer start-up
1. Read RCxREG to clear RXxIF. intervals (i.e., LP, XT or HS/PLL mode). The Sync
2. If RCIDL is ‘0’ then wait for RDCIF and repeat Break (or wake-up signal) character must be of
step 1. sufficient length, and be followed by a sufficient
3. Clear the ABDOVF bit. interval, to allow enough time for the selected oscillator
to start and provide proper initialization of the EUSART.
33.3.3 AUTO-WAKE-UP ON BREAK WUE Bit
During Sleep mode, all clocks to the EUSART are The wake-up event causes a receive interrupt by
suspended. Because of this, the Baud Rate Generator setting the RXxIF bit. The WUE bit is cleared in
is inactive and a proper character reception cannot be hardware by a rising edge on RX/DT. The interrupt
performed. The Auto-Wake-up feature allows the condition is then cleared in software by reading the
controller to wake-up due to activity on the RX/DT line. RCxREG register and discarding its contents.
This feature is available only in Asynchronous mode.
To ensure that no actual data is lost, check the RCIDL
The Auto-Wake-up feature is enabled by setting the bit to verify that a receive operation is not in process
WUE bit of the BAUDxCON register. Once set, the before setting the WUE bit. If a receive operation is not
normal receive sequence on RX/DT is disabled, and the occurring, the WUE bit may then be set just prior to
EUSART remains in an Idle state, monitoring for a wake- entering the Sleep mode.
up event independent of the CPU mode. A wake-up
event consists of a high-to-low transition on the RX/DT
line. (This coincides with the start of a Sync Break or a
wake-up signal character for the LIN protocol.)
The EUSART module generates an RXxIF interrupt
coincident with the wake-up event. The interrupt is
generated synchronously to the Q clocks in normal CPU
operating modes (Figure 33-7), and asynchronously if
the device is in Sleep mode (Figure 33-8). The interrupt
condition is cleared by reading the RCxREG register.
The WUE bit is automatically cleared by the low-to-high
transition on the RX line at the end of the Break. This
signals to the user that the Break event is over. At this
point, the EUSART module is in IDLE mode waiting to
receive the next character.

 2016-2018 Microchip Technology Inc. DS40001866B-page 478


PIC16(L)F15356/75/76/85/86
FIGURE 33-7: AUTO-WAKE-UP BIT (WUE) TIMING DURING NORMAL OPERATION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
Bit set by user Auto Cleared
WUE bit
RX/DT Line

RXxIF
Cleared due to User Read of RCxREG

Note 1: The EUSART remains in Idle while the WUE bit is set.

FIGURE 33-8: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP

Q1Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4


OSC1
Bit Set by User Auto Cleared
WUE bit
RX/DT Line Note 1
RXxIF
Cleared due to User Read of RCxREG
Sleep Command Executed Sleep Ends

Note 1: If the wake-up event requires long oscillator warm-up time, the automatic clearing of the WUE bit can occur while the stposc signal is
still active. This sequence should not depend on the presence of Q clocks.
2: The EUSART remains in Idle while the WUE bit is set.

33.3.4 BREAK CHARACTER SEQUENCE 33.3.4.1 Break and Sync Transmit Sequence
The EUSART module has the capability of sending the The following sequence will start a message frame
special Break character sequences that are required by header made up of a Break, followed by an auto-baud
the LIN bus standard. A Break character consists of a Sync byte. This sequence is typical of a LIN bus
Start bit, followed by 12 ‘0’ bits and a Stop bit. master.
To send a Break character, set the SENDB and TXEN 1. Configure the EUSART for the desired mode.
bits of the TXxSTA register. The Break character 2. Set the TXEN and SENDB bits to enable the
transmission is then initiated by a write to the TXxREG. Break sequence.
The value of data written to TXxREG will be ignored 3. Load the TXxREG with a dummy character to
and all ‘0’s will be transmitted. initiate transmission (the value is ignored).
The SENDB bit is automatically reset by hardware after 4. Write ‘55h’ to TXxREG to load the Sync
the corresponding Stop bit is sent. This allows the user character into the transmit FIFO buffer.
to preload the transmit FIFO with the next transmit byte 5. After the Break has been sent, the SENDB bit is
following the Break character (typically, the Sync reset by hardware and the Sync character is
character in the LIN specification). then transmitted.
The TRMT bit of the TXxSTA register indicates when the When the TXxREG becomes empty, as indicated by
transmit operation is active or idle, just as it does during the TXxIF, the next data byte can be written to TXxREG.
normal transmission. See Figure 33-9 for the timing of
the Break character sequence.

 2016-2018 Microchip Technology Inc. DS40001866B-page 479


PIC16(L)F15356/75/76/85/86
33.3.5 RECEIVING A BREAK CHARACTER
The Enhanced EUSART module can receive a Break
character in two ways.
The first method to detect a Break character uses the
FERR bit of the RCxSTA register and the received data
as indicated by RCxREG. The Baud Rate Generator is
assumed to have been initialized to the expected baud
rate.
A Break character has been received when:
• RXxIF bit is set
• FERR bit is set
• RCxREG = 00h
The second method uses the Auto-Wake-up feature
described in Section 33.3.3 “Auto-Wake-up on
Break”. By enabling this feature, the EUSART will
sample the next two transitions on RX/DT, cause an
RXxIF interrupt, and receive the next data byte fol-
lowed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Detect feature.
For both methods, the user can set the ABDEN bit of
the BAUDxCON register before placing the EUSART in
Sleep mode.

FIGURE 33-9: SEND BREAK CHARACTER SEQUENCE

Write to TXxREG
Dummy Write

BRG Output
(Shift Clock)

TX (pin) Start bit bit 0 bit 1 bit 11 Stop bit


Break
TXxIF bit
(Transmit
Interrupt Flag)
TRMT bit
(Transmit Shift
Empty Flag)
SENDB Sampled Here Auto Cleared
SENDB
(send Break
control bit)

 2016-2018 Microchip Technology Inc. DS40001866B-page 480


PIC16(L)F15356/75/76/85/86
33.4 EUSART Synchronous Mode 33.4.1.2 Clock Polarity
Synchronous serial communications are typically used A clock polarity option is provided for Microwire
in systems with a single master and one or more compatibility. Clock polarity is selected with the SCKP
slaves. The master device contains the necessary bit of the BAUDxCON register. Setting the SCKP bit
circuitry for baud rate generation and supplies the clock sets the clock Idle state as high. When the SCKP bit is
for all devices in the system. Slave devices can take set, the data changes on the falling edge of each clock.
advantage of the master clock by eliminating the Clearing the SCKP bit sets the Idle state as low. When
internal clock generation circuitry. the SCKP bit is cleared, the data changes on the rising
edge of each clock.
There are two signal lines in Synchronous mode: a
bidirectional data line and a clock line. Slaves use the 33.4.1.3 Synchronous Master Transmission
external clock supplied by the master to shift the serial
data into and out of their respective receive and trans- Data is transferred out of the device on the RX/DT pin.
mit shift registers. Since the data line is bidirectional, The RX/DT and TX/CK pin output drivers are automat-
synchronous operation is half-duplex only. Half-duplex ically enabled when the EUSART is configured for
refers to the fact that master and slave devices can synchronous master transmit operation.
receive and transmit data but not both simultaneously. A transmission is initiated by writing a character to the
The EUSART can operate as either a master or slave TXxREG register. If the TSR still contains all or part of
device. a previous character the new character data is held in
Start and Stop bits are not used in synchronous the TXxREG until the last bit of the previous character
transmissions. has been transmitted. If this is the first character, or the
previous character has been completely flushed from
33.4.1 SYNCHRONOUS MASTER MODE the TSR, the data in the TXxREG is immediately trans-
ferred to the TSR. The transmission of the character
The following bits are used to configure the EUSART commences immediately following the transfer of the
for synchronous master operation: data to the TSR from the TXxREG.
• SYNC = 1 Each data bit changes on the leading edge of the
• CSRC = 1 master clock and remains valid until the subsequent
• SREN = 0 (for transmit); SREN = 1 (for receive) leading clock edge.
• CREN = 0 (for transmit); CREN = 1 (for receive) Note: The TSR register is not mapped in data
• SPEN = 1 memory, so it is not available to the user.
Setting the SYNC bit of the TXxSTA register configures
the device for synchronous operation. Setting the CSRC 33.4.1.4 Synchronous Master Transmission
bit of the TXxSTA register configures the device as a Set-up:
master. Clearing the SREN and CREN bits of the 1. Initialize the SPxBRGH, SPxBRGL register pair
RCxSTA register ensures that the device is in the and the BRGH and BRG16 bits to achieve the
Transmit mode, otherwise the device will be configured desired baud rate (see Section 33.3 “EUSART
to receive. Setting the SPEN bit of the RCxSTA register Baud Rate Generator (BRG)”).
enables the EUSART.
2. Enable the synchronous master serial port by
33.4.1.1 Master Clock setting bits SYNC, SPEN and CSRC.
3. Disable Receive mode by clearing bits SREN
Synchronous data transfers use a separate clock line,
and CREN.
which is synchronous with the data. A device config-
ured as a master transmits the clock on the TX/CK line. 4. Enable Transmit mode by setting the TXEN bit.
The TX/CK pin output driver is automatically enabled 5. If 9-bit transmission is desired, set the TX9 bit.
when the EUSART is configured for synchronous 6. If interrupts are desired, set the TXxIE bit of the
transmit or receive operation. Serial data bits change PIE3 register and the GIE and PEIE bits of the
on the leading edge to ensure they are valid at the INTCON register.
trailing edge of each clock. One clock cycle is gener- 7. If 9-bit transmission is selected, the ninth bit
ated for each data bit. Only as many clock cycles are should be loaded in the TX9D bit.
generated as there are data bits. 8. Start transmission by loading data to the
TXxREG register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 481


PIC16(L)F15356/75/76/85/86
FIGURE 33-10: SYNCHRONOUS TRANSMISSION
RX/DT
pin bit 0 bit 1 bit 2 bit 7 bit 0 bit 1 bit 7
Word 1 Word 2
TX/CK pin
(SCKP = 0)

TX/CK pin
(SCKP = 1)
Write to
TXxREG Reg Write Word 1 Write Word 2
TXxIF bit
(Interrupt Flag)

TRMT bit

‘1’ ‘1’
TXEN bit

Note: Sync Master mode, SPxBRGL = 0, continuous transmission of two 8-bit words.

FIGURE 33-11: SYNCHRONOUS TRANSMISSION (THROUGH TXEN)

RX/DT pin bit 0 bit 1 bit 2 bit 6 bit 7

TX/CK pin

Write to
TXxREG reg

TXxIF bit

TRMT bit

TXEN bit

33.4.1.5 Synchronous Master Reception To initiate reception, set either SREN or CREN. Data is
sampled at the RX/DT pin on the trailing edge of the
Data is received at the RX/DT pin. The RX/DT pin
TX/CK clock pin and is shifted into the Receive Shift
output driver is automatically disabled when the
Register (RSR). When a complete character is
EUSART is configured for synchronous master receive
received into the RSR, the RXxIF bit is set and the
operation.
character is automatically transferred to the two char-
In Synchronous mode, reception is enabled by setting acter receive FIFO. The Least Significant eight bits of
either the Single Receive Enable bit (SREN of the the top character in the receive FIFO are available in
RCxSTA register) or the Continuous Receive Enable RCxREG. The RXxIF bit remains set as long as there
bit (CREN of the RCxSTA register). are unread characters in the receive FIFO.
When SREN is set and CREN is clear, only as many Note: If the RX/DT function is on an analog pin,
clock cycles are generated as there are data bits in a the corresponding ANSEL bit must be
single character. The SREN bit is automatically cleared cleared for the receiver to function.
at the completion of one character. When CREN is set,
clocks are continuously generated until CREN is
cleared. If CREN is cleared in the middle of a character
the CK clock stops immediately and the partial charac-
ter is discarded. If SREN and CREN are both set, then
SREN is cleared at the completion of the first character
and CREN takes precedence.

 2016-2018 Microchip Technology Inc. DS40001866B-page 482


PIC16(L)F15356/75/76/85/86
33.4.1.6 Slave Clock received. The RX9D bit of the RCxSTA register is the
ninth, and Most Significant, data bit of the top unread
Synchronous data transfers use a separate clock line,
character in the receive FIFO. When reading 9-bit data
which is synchronous with the data. A device configured
from the receive FIFO buffer, the RX9D data bit must
as a slave receives the clock on the TX/CK line. The TX/
be read before reading the eight Least Significant bits
CK pin output driver is automatically disabled when the
from the RCxREG.
device is configured for synchronous slave transmit or
receive operation. Serial data bits change on the leading
33.4.1.9 Synchronous Master Reception Set-
edge to ensure they are valid at the trailing edge of each
up:
clock. One data bit is transferred for each clock cycle.
Only as many clock cycles should be received as there 1. Initialize the SPxBRGH, SPxBRGL register pair
are data bits. for the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
Note: If the device is configured as a slave and the desired baud rate.
the TX/CK function is on an analog pin, the
2. Clear the ANSEL bit for the RX pin (if applicable).
corresponding ANSEL bit must be cleared.
3. Enable the synchronous master serial port by
33.4.1.7 Receive Overrun Error setting bits SYNC, SPEN and CSRC.
4. Ensure bits CREN and SREN are clear.
The receive FIFO buffer can hold two characters. An
overrun error will be generated if a third character, in its 5. If interrupts are desired, set the RXxIE bit of the
entirety, is received before RCxREG is read to access PIE3 register and the GIE and PEIE bits of the
the FIFO. When this happens the OERR bit of the INTCON register.
RCxSTA register is set. Previous data in the FIFO will 6. If 9-bit reception is desired, set bit RX9.
not be overwritten. The two characters in the FIFO 7. Start reception by setting the SREN bit or for
buffer can be read, however, no additional characters continuous reception, set the CREN bit.
will be received until the error is cleared. The OERR bit 8. Interrupt flag bit RXxIF will be set when recep-
can only be cleared by clearing the overrun condition. tion of a character is complete. An interrupt will
If the overrun error occurred when the SREN bit is set be generated if the enable bit RXxIE was set.
and CREN is clear then the error is cleared by reading 9. Read the RCxSTA register to get the ninth bit (if
RCxREG. If the overrun occurred when the CREN bit is enabled) and determine if any error occurred
set then the error condition is cleared by either clearing during reception.
the CREN bit of the RCxSTA register or by clearing the
10. Read the 8-bit received data by reading the
SPEN bit which resets the EUSART.
RCxREG register.
33.4.1.8 Receiving 9-bit Characters 11. If an overrun error occurs, clear the error by
either clearing the CREN bit of the RCxSTA
The EUSART supports 9-bit character reception. When
register or by clearing the SPEN bit which resets
the RX9 bit of the RCxSTA register is set the EUSART
the EUSART.
will shift nine bits into the RSR for each character

FIGURE 33-12: SYNCHRONOUS RECEPTION (MASTER MODE, SREN)

RX/DT
pin bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7

TX/CK pin
(SCKP = 0)

TX/CK pin
(SCKP = 1)

Write to
bit SREN

SREN bit

CREN bit ‘0’ ‘0’

RXxIF bit
(Interrupt)
Read
RCxREG

Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.

 2016-2018 Microchip Technology Inc. DS40001866B-page 483


PIC16(L)F15356/75/76/85/86
33.4.2 SYNCHRONOUS SLAVE MODE 33.4.2.1 EUSART Synchronous Slave
The following bits are used to configure the EUSART Transmit
for synchronous slave operation: The operation of the Synchronous Master and Slave
• SYNC = 1 modes are identical (see Section 33.4.1.3
“Synchronous Master Transmission”), except in the
• CSRC = 0
case of the Sleep mode.
• SREN = 0 (for transmit); SREN = 1 (for receive)
If two words are written to the TXxREG and then the
• CREN = 0 (for transmit); CREN = 1 (for receive)
SLEEP instruction is executed, the following will occur:
• SPEN = 1
1. The first character will immediately transfer to
Setting the SYNC bit of the TXxSTA register configures the TSR register and transmit.
the device for synchronous operation. Clearing the
2. The second word will remain in the TXxREG
CSRC bit of the TXxSTA register configures the device as
register.
a slave. Clearing the SREN and CREN bits of the
RCxSTA register ensures that the device is in the 3. The TXxIF bit will not be set.
Transmit mode, otherwise the device will be configured to 4. After the first character has been shifted out of
receive. Setting the SPEN bit of the RCxSTA register TSR, the TXxREG register will transfer the
enables the EUSART. second character to the TSR and the TXxIF bit
will now be set.
5. If the PEIE and TXxIE bits are set, the interrupt
will wake the device from Sleep and execute the
next instruction. If the GIE bit is also set, the
program will call the Interrupt Service Routine.

33.4.2.2 Synchronous Slave Transmission


Set-up:
1. Set the SYNC and SPEN bits and clear the
CSRC bit.
2. Clear the ANSEL bit for the CK pin (if applicable).
3. Clear the CREN and SREN bits.
4. If interrupts are desired, set the TXxIE bit of the
PIE3 register and the GIE and PEIE bits of the
INTCON register.
5. If 9-bit transmission is desired, set the TX9 bit.
6. Enable transmission by setting the TXEN bit.
7. If 9-bit transmission is selected, insert the Most
Significant bit into the TX9D bit.
8. Start transmission by writing the Least
Significant eight bits to the TXxREG register.

 2016-2018 Microchip Technology Inc. DS40001866B-page 484


PIC16(L)F15356/75/76/85/86
33.4.2.3 EUSART Synchronous Slave 33.4.2.4 Synchronous Slave Reception Set-
Reception up:
The operation of the Synchronous Master and Slave 1. Set the SYNC and SPEN bits and clear the
modes is identical (Section 33.4.1.5 “Synchronous CSRC bit.
Master Reception”), with the following exceptions: 2. Clear the ANSEL bit for both the CK and DT pins
• Sleep (if applicable).
• CREN bit is always set, therefore the receiver is 3. If interrupts are desired, set the RXxIE bit of the
never idle PIE3 register and the GIE and PEIE bits of the
• SREN bit, which is a “don’t care” in Slave mode INTCON register.
4. If 9-bit reception is desired, set the RX9 bit.
A character may be received while in Sleep mode by
setting the CREN bit prior to entering Sleep. Once the 5. Set the CREN bit to enable reception.
word is received, the RSR register will transfer the data 6. The RXxIF bit will be set when reception is
to the RCxREG register. If the RXxIE enable bit is set, complete. An interrupt will be generated if the
the interrupt generated will wake the device from Sleep RXxIE bit was set.
and execute the next instruction. If the GIE bit is also 7. If 9-bit mode is enabled, retrieve the Most
set, the program will branch to the interrupt vector. Significant bit from the RX9D bit of the RCxSTA
register.
8. Retrieve the eight Least Significant bits from the
receive FIFO by reading the RCxREG register.
9. If an overrun error occurs, clear the error by
either clearing the CREN bit of the RCxSTA
register or by clearing the SPEN bit which resets
the EUSART.

 2016-2018 Microchip Technology Inc. DS40001866B-page 485


PIC16(L)F15356/75/76/85/86
33.5 EUSART Operation During Sleep 33.5.2 SYNCHRONOUS TRANSMIT
DURING SLEEP
The EUSART will remain active during Sleep only in the
Synchronous Slave mode. All other modes require the To transmit during Sleep, all the following conditions
system clock and therefore cannot generate the neces- must be met before entering Sleep mode:
sary signals to run the Transmit or Receive Shift • The RCxSTA and TXxSTA Control registers must
registers during Sleep. be configured for synchronous slave transmission
Synchronous Slave mode uses an externally generated (see Section 33.4.2.2 “Synchronous Slave
clock to run the Transmit and Receive Shift registers. Transmission Set-up:”).
• The TXxIF interrupt flag must be cleared by writ-
33.5.1 SYNCHRONOUS RECEIVE DURING ing the output data to the TXxREG, thereby filling
SLEEP the TSR and transmit buffer.
To receive during Sleep, all the following conditions • If interrupts are desired, set the TXxIE bit of the
must be met before entering Sleep mode: PIE3 register and the PEIE bit of the INTCON
register.
• RCxSTA and TXxSTA Control registers must be
configured for Synchronous Slave Reception (see • Interrupt enable bits TXxIE of the PIE3 register
Section 33.4.2.4 “Synchronous Slave and PEIE of the INTCON register must set.
Reception Set-up:”). Upon entering Sleep mode, the device will be ready to
• If interrupts are desired, set the RXxIE bit of the accept clocks on TX/CK pin and transmit data on the
PIE3 register and the GIE and PEIE bits of the RX/DT pin. When the data word in the TSR has been
INTCON register. completely clocked out by the external device, the
• The RXxIF interrupt flag must be cleared by read- pending byte in the TXxREG will transfer to the TSR
ing RCxREG to unload any pending characters in and the TXxIF flag will be set. Thereby, waking the
the receive buffer. processor from Sleep. At this point, the TXxREG is
available to accept another character for transmission,
Upon entering Sleep mode, the device will be ready to which will clear the TXxIF flag.
accept data and clocks on the RX/DT and TX/CK pins,
respectively. When the data word has been completely Upon waking from Sleep, the instruction following the
clocked in by the external device, the RXxIF interrupt SLEEP instruction will be executed. If the Global
flag bit of the PIR3 register will be set. Thereby, waking Interrupt Enable (GIE) bit is also set then the Interrupt
the processor from Sleep. Service Routine at address 0004h will be called.

Upon waking from Sleep, the instruction following the


SLEEP instruction will be executed. If the Global
Interrupt Enable (GIE) bit of the INTCON register is
also set, then the Interrupt Service Routine at address
004h will be called.

 2016-2018 Microchip Technology Inc. DS40001866B-page 486


PIC16(L)F15356/75/76/85/86
33.6 Register Definitions: EUSART Control
REGISTER 33-1: TXxSTA: TRANSMIT STATUS AND CONTROL REGISTER
R/W-/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-1/1 R/W-0/0
CSRC TX9 TXEN(1) SYNC SENDB BRGH TRMT TX9D
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 CSRC: Clock Source Select bit


Asynchronous mode:
Unused in this mode – value ignored
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6 TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5 TXEN: Transmit Enable bit(1)
1 = Transmit enabled
0 = Transmit disabled
bit 4 SYNC: EUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3 SENDB: Send Break Character bit
Asynchronous mode:
1 = Send SYNCH BREAK on next transmission – Start bit, followed by 12 ‘0’ bits, followed by Stop
bit; cleared by hardware upon completion
0 = SYNCH BREAK transmission disabled or completed
Synchronous mode:
Unused in this mode – value ignored
bit 2 BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode – value ignored
bit 1 TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0 TX9D: Ninth bit of Transmit Data
Can be address/data bit or a parity bit.

Note 1: SREN/CREN overrides TXEN in Sync mode.

 2016-2018 Microchip Technology Inc. DS40001866B-page 487


PIC16(L)F15356/75/76/85/86

REGISTER 33-2: RCxSTA: RECEIVE STATUS AND CONTROL REGISTER


R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-0/0 R-0/0 R-0/0
SPEN(1) RX9 SREN CREN ADDEN FERR OERR RX9D
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 SPEN: Serial Port Enable bit(1)


1 = Serial port enabled
0 = Serial port disabled (held in Reset)
bit 6 RX9: 9-Bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5 SREN: Single Receive Enable bit
Asynchronous mode:
Unused in this mode – value ignored
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode – Slave
Unused in this mode – value ignored
bit 4 CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared
0 = Disables continuous receive
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3 ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection – enable interrupt and load of the receive buffer when the ninth bit in
the receive buffer is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
Asynchronous mode 8-bit (RX9 = 0):
Unused in this mode – value ignored
bit 2 FERR: Framing Error bit
1 = Framing error (can be updated by reading RCxREG register and receive next valid byte)
0 = No framing error
bit 1 OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0 RX9D: Ninth bit of Received Data
This can be address/data bit or a parity bit and must be calculated by user firmware.

Note 1: The EUSART module automatically changes the pin from tri-state to drive as needed. Configure the
associated TRIS bits for TX/CK and RX/DT to 1.

 2016-2018 Microchip Technology Inc. DS40001866B-page 488


PIC16(L)F15356/75/76/85/86

REGISTER 33-3: BAUDxCON: BAUD RATE CONTROL REGISTER


R/W-0/0 R-1/1 U-0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0
ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 ABDOVF: Auto-Baud Detect Overflow bit


Asynchronous mode:
1 = Auto-baud timer overflowed
0 = Auto-baud timer did not overflow
Synchronous mode:
Don’t care
bit 6 RCIDL: Receive Idle Flag bit
Asynchronous mode:
1 = Receiver is Idle
0 = Start bit has been received and the receiver is receiving
Synchronous mode:
Don’t care
bit 5 Unimplemented: Read as ‘0’
bit 4 SCKP: Clock/Transmit Polarity Select bit
Asynchronous mode:
1 = Idle state for transmit (TX) is a low level
0 = Idle state for transmit (TX) is a high level
Synchronous mode:
1 = Idle state for clock (CK) is a high level
0 = Idle state for clock (CK) is a low level
bit 3 BRG16: 16-bit Baud Rate Generator bit
1 = 16-bit Baud Rate Generator is used
0 = 8-bit Baud Rate Generator is used
bit 2 Unimplemented: Read as ‘0’
bit 1 WUE: Wake-up Enable bit
Asynchronous mode:
1 = USART will continue to sample the Rx pin – interrupt generated on falling edge; bit cleared in
hardware on following rising edge.
0 = RX pin not monitored nor rising edge detected
Synchronous mode:
Unused in this mode – value ignored
bit 0 ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character – requires reception of a SYNCH field
(55h);
cleared in hardware upon completion
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode – value ignored

 2016-2018 Microchip Technology Inc. DS40001866B-page 489


PIC16(L)F15356/75/76/85/86
REGISTER 33-4: RCxREG(1): RECEIVE DATA REGISTER
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
RCxREG<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 RCxREG<7:0>: Lower eight bits of the received data; read-only; see also RX9D (Register 33-2)

Note 1: RCxREG (including the 9th bit) is double buffered, and data is available while new data is being received.

REGISTER 33-5: TXxREG(1): TRANSMIT DATA REGISTER


R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
TXxREG<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 TXxREG<7:0>: Lower eight bits of the received data; read-only; see also RX9D (Register 33-1)

Note 1: TXxREG (including the 9th bit) is double buffered, and can be written when previous data has started
shifting.

REGISTER 33-6: SPxBRGL(1): BAUD RATE GENERATOR REGISTER


R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
SPxBRG<7:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-0 SPxBRG<7:0>: Lower eight bits of the Baud Rate Generator

Note 1: Writing to SP1BRG resets the BRG counter.

 2016-2018 Microchip Technology Inc. DS40001866B-page 490


PIC16(L)F15356/75/76/85/86
REGISTER 33-7: SPxBRGH(1, 2): BAUD RATE GENERATOR HIGH REGISTER
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
SPxBRG<15:8>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 SPxBRG<15:8>: Upper eight bits of the Baud Rate Generator

Note 1: SPxBRGH value is ignored for all modes unless BAUDxCON<BRG16> is active.
2: Writing to SPxBRGH resets the BRG counter.

 2016-2018 Microchip Technology Inc. DS40001866B-page 491


PIC16(L)F15356/75/76/85/86

TABLE 33-2: SUMMARY OF REGISTERS ASSOCIATED WITH EUSART

Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page

INTCON GIE PEIE ― ― ― ― ― INTEDG 147


PIE3 RC2IE TX2IE RC1IE TX1IE BCL2IE SSP2IE BCL1IE SSP1IE 151
PIR3 RC2IF TX2IF RC1IF TX1IF BCL2IF SSP2IF BCL1IF SSP1IF 159
RCxSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 488
TXxSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 487
BAUDxCON ABDOVF RCIDL ― SCKP BRG16 ― WUE ABDEN 489
RCxREG EUSART Receive Data Register 490*
TXxREG EUSART Transmit Data Register 490*
SPxBRGL SPxBRG<7:0> 490*
SPxBRGH SPxBRG<15:8> 491*
RXPPS ― ― RXPPS<5:0> 242
CKPPS ― ― CXPPS<5:0> 242
RxyPPS ― ― ― RxyPPS<4:0> 243
CLCxSELy ― ― LCxDyS<5:0> 409
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used for the EUSART module.
* Page with register information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 492


PIC16(L)F15356/75/76/85/86
TABLE 33-3: BAUD RATE FORMULAS
Configuration Bits
BRG/EUSART Mode Baud Rate Formula
SYNC BRG16 BRGH

0 0 0 8-bit/Asynchronous FOSC/[64 (n+1)]


0 0 1 8-bit/Asynchronous
FOSC/[16 (n+1)]
0 1 0 16-bit/Asynchronous
0 1 1 16-bit/Asynchronous
1 0 x 8-bit/Synchronous FOSC/[4 (n+1)]
1 1 x 16-bit/Synchronous
Legend: x = Don’t care, n = value of SPxBRGH, SPxBRGL register pair.

TABLE 33-4: BAUD RATE FOR ASYNCHRONOUS MODES


SYNC = 0, BRGH = 0, BRG16 = 0
FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
BAUD
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 — — — — — — — — — — — —
1200 — — — 1221 1.73 255 1200 0.00 239 1200 0.00 143
2400 2404 0.16 207 2404 0.16 129 2400 0.00 119 2400 0.00 71
9600 9615 0.16 51 9470 -1.36 32 9600 0.00 29 9600 0.00 17
10417 10417 0.00 47 10417 0.00 29 10286 -1.26 27 10165 -2.42 16
19.2k 19.23k 0.16 25 19.53k 1.73 15 19.20k 0.00 14 19.20k 0.00 8
57.6k 55.55k -3.55 3 — — — 57.60k 0.00 7 57.60k 0.00 2
115.2k — — — — — — — — — — — —

SYNC = 0, BRGH = 0, BRG16 = 0

BAUD FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 — — — 300 0.16 207 300 0.00 191 300 0.16 51
1200 1202 0.16 103 1202 0.16 51 1200 0.00 47 1202 0.16 12
2400 2404 0.16 51 2404 0.16 25 2400 0.00 23 — — —
9600 9615 0.16 12 — — — 9600 0.00 5 — — —
10417 10417 0.00 11 10417 0.00 5 — — — — — —
19.2k — — — — — — 19.20k 0.00 2 — — —
57.6k — — — — — — 57.60k 0.00 0 — — —
115.2k — — — — — — — — — — — —

 2016-2018 Microchip Technology Inc. DS40001866B-page 493


PIC16(L)F15356/75/76/85/86
TABLE 33-4: BAUD RATE FOR ASYNCHRONOUS MODES (CONTINUED)
SYNC = 0, BRGH = 1, BRG16 = 0

BAUD FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 — — — — — — — — — — — —
1200 — — — — — — — — — — — —
2400 — — — — — — — — — — — —
9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71
10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65
19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35
57.6k 57.14k -0.79 34 56.82k -1.36 21 57.60k 0.00 19 57.60k 0.00 11
115.2k 117.64k 2.12 16 113.64k -1.36 10 115.2k 0.00 9 115.2k 0.00 5

SYNC = 0, BRGH = 1, BRG16 = 0

BAUD FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 — — — — — — — — — 300 0.16 207
1200 — — — 1202 0.16 207 1200 0.00 191 1202 0.16 51
2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25
9600 9615 0.16 51 9615 0.16 25 9600 0.00 23 — — —
10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 10417 0.00 5
19.2k 19231 0.16 25 19.23k 0.16 12 19.2k 0.00 11 — — —
57.6k 55556 -3.55 8 — — — 57.60k 0.00 3 — — —
115.2k — — — — — — 115.2k 0.00 1 — — —

SYNC = 0, BRGH = 0, BRG16 = 1

BAUD FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 300.0 0.00 6666 300.0 -0.01 4166 300.0 0.00 3839 300.0 0.00 2303
1200 1200 -0.02 3332 1200 -0.03 1041 1200 0.00 959 1200 0.00 575
2400 2401 -0.04 832 2399 -0.03 520 2400 0.00 479 2400 0.00 287
9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71
10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65
19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35
57.6k 57.14k -0.79 34 56.818 -1.36 21 57.60k 0.00 19 57.60k 0.00 11
115.2k 117.6k 2.12 16 113.636 -1.36 10 115.2k 0.00 9 115.2k 0.00 5

 2016-2018 Microchip Technology Inc. DS40001866B-page 494


PIC16(L)F15356/75/76/85/86
TABLE 33-4: BAUD RATE FOR ASYNCHRONOUS MODES (CONTINUED)
SYNC = 0, BRGH = 0, BRG16 = 1

BAUD FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 299.9 -0.02 1666 300.1 0.04 832 300.0 0.00 767 300.5 0.16 207
1200 1199 -0.08 416 1202 0.16 207 1200 0.00 191 1202 0.16 51
2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25
9600 9615 0.16 51 9615 0.16 25 9600 0.00 23 — — —
10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 10417 0.00 5
19.2k 19.23k 0.16 25 19.23k 0.16 12 19.20k 0.00 11 — — —
57.6k 55556 -3.55 8 — — — 57.60k 0.00 3 — — —
115.2k — — — — — — 115.2k 0.00 1 — — —

SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1

BAUD FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 300.0 0.00 26666 300.0 0.00 16665 300.0 0.00 15359 300.0 0.00 9215
1200 1200 0.00 6666 1200 -0.01 4166 1200 0.00 3839 1200 0.00 2303
2400 2400 0.01 3332 2400 0.02 2082 2400 0.00 1919 2400 0.00 1151
9600 9604 0.04 832 9597 -0.03 520 9600 0.00 479 9600 0.00 287
10417 10417 0.00 767 10417 0.00 479 10425 0.08 441 10433 0.16 264
19.2k 19.18k -0.08 416 19.23k 0.16 259 19.20k 0.00 239 19.20k 0.00 143
57.6k 57.55k -0.08 138 57.47k -0.22 86 57.60k 0.00 79 57.60k 0.00 47
115.2k 115.9k 0.64 68 116.3k 0.94 42 115.2k 0.00 39 115.2k 0.00 23

SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1

BAUD FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
RATE SPBRG SPBRG SPBRG SPBRG
Actual % Actual % Actual % Actual %
value value value value
Rate Error Rate Error Rate Error Rate Error
(decimal) (decimal) (decimal) (decimal)
300 300.0 0.00 6666 300.0 0.01 3332 300.0 0.00 3071 300.1 0.04 832
1200 1200 -0.02 1666 1200 0.04 832 1200 0.00 767 1202 0.16 207
2400 2401 0.04 832 2398 0.08 416 2400 0.00 383 2404 0.16 103
9600 9615 0.16 207 9615 0.16 103 9600 0.00 95 9615 0.16 25
10417 10417 0 191 10417 0.00 95 10473 0.53 87 10417 0.00 23
19.2k 19.23k 0.16 103 19.23k 0.16 51 19.20k 0.00 47 19.23k 0.16 12
57.6k 57.14k -0.79 34 58.82k 2.12 16 57.60k 0.00 15 — — —
115.2k 117.6k 2.12 16 111.1k -3.55 8 115.2k 0.00 7 — — —

 2016-2018 Microchip Technology Inc. DS40001866B-page 495


PIC16(L)F15356/75/76/85/86
34.0 REFERENCE CLOCK OUTPUT 34.3 SELECTABLE DUTY CYCLE
MODULE The CLKRDC<1:0> bits of the CLKRCON register can
The reference clock output module provides the ability be used to modify the duty cycle of the output clock. A
to send a clock signal to the clock reference output pin duty cycle of 25%, 50%, or 75% can be selected for all
(CLKR). clock rates, with the exception of the undivided base
FOSC value.
The reference clock output module has the following
features: The duty cycle can be changed while the module is
enabled; however, in order to prevent glitches on the
• Selectable input clock output, the CLKRDC<1:0> bits should only be changed
• Programmable clock divider when the module is disabled (CLKREN = 0).
• Selectable duty cycle

34.1 CLOCK SOURCE Note: The CLKRDC1 bit is reset to ‘1’. This
makes the default duty cycle 50% and not
The reference clock output module has a selectable 0%.
clock source. The CLKRCLK register (Register 34-2)
controls which input is used.
34.4 OPERATION IN SLEEP MODE
34.1.1 CLOCK SYNCHRONIZATION
The reference clock output module clock is based on
Once the reference clock enable (CLKREN) is set, the the system clock. When the device goes to Sleep, the
module is ensured to be glitch-free at start-up. module outputs will remain in their current state. This
When the reference clock output is disabled, the output will have a direct effect on peripherals using the
signal will be disabled immediately. reference clock output as an input signal.

Clock dividers and clock duty cycles can be changed


while the module is enabled, but glitches may occur on
the output. To avoid possible glitches, clock dividers
and clock duty cycles should be changed only when the
CLKREN is clear.

34.2 PROGRAMMABLE CLOCK


DIVIDER
The module takes the system clock input and divides it
based on the value of the CLKRDIV<2:0> bits of the
CLKRCON register (Register 34-1).
The following configurations can be made based on the
CLKRDIV<2:0> bits:
• Base clock value
• Base clock value divided by 2
• Base clock value divided by 4
• Base clock value divided by 8
• Base clock value divided by 16
• Base clock value divided by 32
• Base clock value divided by 64
• Base clock value divided by 128
The clock divider values can be changed while the
module is enabled; however, in order to prevent
glitches on the output, the CLKRDIV<2:0> bits should
only be changed when the module is disabled
(CLKREN = 0).

 2016-2018 Microchip Technology Inc. DS40001866B-page 496


PIC16(L)F15356/75/76/85/86
FIGURE 34-1: CLOCK REFERENCE BLOCK DIAGRAM

Rev. 10-000261A
9/10/2015

CLKRDIV<2:0>
CLKREN Counter Reset
128
111

Reference Clock Divider


See 64 CLKRDC<1:0>
110
CLKRCLK 32
Register 101
16 CLKR
100
8 Duty Cycle PPS
011
4
010
2
001 To Peripherals

CLKREN
D Q 000
CLKRCLK<3:0>
FREEZE ENABLED(1) EN
ICD FREEZE MODE(1)

FIGURE 34-2: CLOCK REFERENCE TIMING

P1 P2

FOSC

CLKREN

CLKR Output
CLKRDIV[2:0] = 001
Duty Cycle
CLKRDC[1:0] = 10
(50%)

CLKR Output FOSC / 2


CLKRDIV[2:0] = 001
CLKRDC[1:0] = 01

Duty Cycle (25%)

 2016-2018 Microchip Technology Inc. DS40001866B-page 497


PIC16(L)F15356/75/76/85/86
34.5 Register Definition: Reference Clock Output Control

REGISTER 34-1: CLKRCON: REFERENCE CLOCK CONTROL REGISTER


R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CLKREN — — CLKRDC<1:0> CLKRDIV<2:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7 CLKREN: Reference Clock Module Enable bit


1 = Reference clock module enabled
0 = Reference clock module is disabled
bit 6-5 Unimplemented: Read as ‘0’
bit 4-3 CLKRDC<1:0>: Reference Clock Duty Cycle bits (1)
11 = Clock outputs duty cycle of 75%
10 = Clock outputs duty cycle of 50%
01 = Clock outputs duty cycle of 25%
00 = Clock outputs duty cycle of 0%
bit 2-0 CLKRDIV<2:0>: Reference Clock Divider bits
111 = Base clock value divided by 128
110 = Base clock value divided by 64
101 = Base clock value divided by 32
100 = Base clock value divided by 16
011 = Base clock value divided by 8
010 = Base clock value divided by 4
001 = Base clock value divided by 2
000 = Base clock value

Note 1: Bits are valid for reference clock divider values of two or larger, the base clock cannot be further divided.

 2016-2018 Microchip Technology Inc. DS40001866B-page 498


PIC16(L)F15356/75/76/85/86
REGISTER 34-2: CLKRCLK: CLOCK REFERENCE CLOCK SELECTION REGISTER
U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
— — — — CLKRCLK<3:0>
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared

bit 7-4 Unimplemented: Read as ‘0’


bit 3-0 CLKRCLK<3:0>: CLKR Input bits
Clock Selection
1111 = Reserved



1011 = Reserved
1010 = LC4_out
1001 = LC3_out
1000 = LC2_out
0111 = LC1_out
0110 = NCO1_out
0101 = SOSC
0100 = MFINTOSC (31.25 kHz)
0011 = MFINTOSC (500 kHz)
0010 = LFINTOSC
0001 = HFINTOSC
0000 = FOSC

TABLE 34-1: SUMMARY OF REGISTERS ASSOCIATED WITH CLOCK REFERENCE OUTPUT


Register
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
on Page
CLKRCON CLKREN — — CLKRDC<1:0> CLKRDIV<2:0> 498
CLKRCLK — — — — CLKRCLK<3:0> 499
CLCxSELy — — LCxDyS<5:0> 409
RxyPPS — — — RxyPPS<4:0> 243
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the CLKR module.

 2016-2018 Microchip Technology Inc. DS40001866B-page 499


PIC16(L)F15356/75/76/85/86
35.0 IN-CIRCUIT SERIAL 35.3 Common Programming Interfaces
PROGRAMMING™ (ICSP™) Connection to a target device is typically done through
ICSP™ programming allows customers to manufacture an ICSP™ header. A commonly found connector on
circuit boards with unprogrammed devices. Programming development tools is the RJ-11 in the 6P6C (6-pin, 6-
can be done after the assembly process, allowing the connector) configuration. See Figure 35-1.
device to be programmed with the most recent firmware
or a custom firmware. Five pins are needed for ICSP™ FIGURE 35-1: ICD RJ-11 STYLE
programming: CONNECTOR INTERFACE
• ICSPCLK
• ICSPDAT
• MCLR/VPP
• VDD
ICSPDAT
• VSS
2 4 6 NC
VDD
In Program/Verify mode the program memory, User IDs ICSPCLK
and the Configuration Words are programmed through 1 3 5
Target
serial communications. The ICSPDAT pin is a VPP/MCLR PC Board
VSS
bidirectional I/O used for transferring the serial data Bottom Side
and the ICSPCLK pin is the clock input. For more
information on ICSP™ refer to the “PIC16(L)F153XX
Memory Programming Specification” (DS40001838). Pin Description*

1 = VPP/MCLR
35.1 High-Voltage Programming Entry 2 = VDD Target
Mode 3 = VSS (ground)

The device is placed into High-Voltage Programming 4 = ICSPDAT

Entry mode by holding the ICSPCLK and ICSPDAT 5 = ICSPCLK


pins low then raising the voltage on MCLR/VPP to VIHH. 6 = No Connect

35.2 Low-Voltage Programming Entry Another connector often found in use with the PICkit™
Mode programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to Figure 35-2.
The Low-Voltage Programming Entry mode allows the
PIC® Flash MCUs to be programmed using VDD only, For additional interface recommendations, refer to your
without high voltage. When the LVP bit of Configuration specific device programmer manual prior to PCB
Words is set to ‘1’, the low-voltage ICSP programming design.
entry is enabled. To disable the Low-Voltage ICSP It is recommended that isolation devices be used to
mode, the LVP bit must be programmed to ‘0’. The LVP separate the programming pins from other circuitry.
bit can only be reprogrammed to ‘0’ by using the High- The type of isolation is highly dependent on the specific
Voltage Programming mode. application and may include devices such as resistors,
Entry into the Low-Voltage Programming Entry mode diodes, or even jumpers. See Figure 35-3 for more
requires the following steps: information.
1. MCLR is brought to VIL.
2. A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
Once the key sequence is complete, MCLR must be
held at VIL for as long as Program/Verify mode is to be
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See Section 8.5 “MCLR” for more
information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 500


PIC16(L)F15356/75/76/85/86
FIGURE 35-2: PICkit™ PROGRAMMER STYLE CONNECTOR INTERFACE
Rev. 10-000128A
7/30/2013

Pin 1 Indicator

Pin Description*
1 = VPP/MCLR
1
2
2 = VDD Target
3
4 3 = VSS (ground)
5
6 4 = ICSPDAT
5 = ICSPCLK
6 = No connect

FIGURE 35-3: TYPICAL CONNECTION FOR ICSP™ PROGRAMMING

Rev. 10-000129A
7/30/2013

External Device to be
Programming VDD Programmed
Signals

VDD VDD

VPP MCLR/VPP
VSS VSS

Data ICSPDAT
Clock ICSPCLK

* * *

To Normal Connections

* Isolation devices (as required).

 2016-2018 Microchip Technology Inc. DS40001866B-page 501


PIC16(L)F15356/75/76/85/86
36.0 INSTRUCTION SET SUMMARY 36.1 Read-Modify-Write Operations
Each instruction is a 14-bit word containing the Any instruction that specifies a file register as part of
operation code (opcode) and all required operands. the instruction performs a Read-Modify-Write (R-M-W)
The opcodes are broken into three broad categories. operation. The register is read, the data is modified,
and the result is stored according in either the working
• Byte Oriented
(W) register, or the originating file register, depending
• Bit Oriented on the state of the destination designator 'd' (see
• Literal and Control Table 36-1 for more information). A read operation is
The literal and control category contains the most performed on a register even if the instruction writes to
varied instruction word format. that register.
Table 36-3 lists the instructions recognized by the
MPASMTM assembler. TABLE 36-1: OPCODE FIELD
DESCRIPTIONS
All instructions are executed within a single instruction
cycle, with the following exceptions, which may take Field Description
two or three cycles: f Register file address (0x00 to 0x7F)
• Subroutine entry takes two cycles (CALL, CALLW) W Working register (accumulator)
• Returns from interrupts or subroutines take two b Bit address within an 8-bit file register
cycles (RETURN, RETLW, RETFIE)
• Program branching takes two cycles (GOTO, BRA, k Literal field, constant data or label
BRW, BTFSS, BTFSC, DECFSZ, INCSFZ) x Don’t care location (= 0 or 1).
• One additional instruction cycle will be used when The assembler will generate code with x = 0.
any instruction references an indirect file register It is the recommended form of use for
and the file select register is pointing to program compatibility with all Microchip software tools.
memory. d Destination select; d = 0: store result in W,
One instruction cycle consists of four oscillator cycles; d = 1: store result in file register f.
for an oscillator frequency of 4 MHz, this gives a n FSR or INDF number. (0-1)
nominal instruction execution rate of 1 MHz. mm Prepost increment-decrement mode selection
All instruction examples use the format ‘0xhh’ to
represent a hexadecimal number, where ‘h’ signifies a TABLE 36-2: ABBREVIATION
hexadecimal digit.
DESCRIPTIONS
Field Description
PC Program Counter
TO Time-Out bit
C Carry bit
DC Digit Carry bit
Z Zero bit
PD Power-Down bit

 2016-2018 Microchip Technology Inc. DS40001866B-page 502


PIC16(L)F15356/75/76/85/86
36.2 General Format for Instructions

TABLE 36-3: INSTRUCTION SET


Mnemonic, 14-Bit Opcode Status
Description Cycles Notes
Operands MSb LSb Affected

BYTE-ORIENTED FILE REGISTER OPERATIONS


ADDWF f, d Add W and f 1 00 0111 dfff ffff C, DC, Z 2
ADDWFC f, d Add with Carry W and f 1 11 1101 dfff ffff C, DC, Z 2
ANDWF f, d AND W with f 1 00 0101 dfff ffff Z 2
ASRF f, d Arithmetic Right Shift 1 11 0111 dfff ffff C, Z 2
LSLF f, d Logical Left Shift 1 11 0101 dfff ffff C, Z 2
LSRF f, d Logical Right Shift 1 11 0110 dfff ffff C, Z 2
CLRF f Clear f 1 00 0001 lfff ffff Z 2
CLRW – Clear W 1 00 0001 0000 00xx Z
COMF f, d Complement f 1 00 1001 dfff ffff Z 2
DECF f, d Decrement f 1 00 0011 dfff ffff Z 2
INCF f, d Increment f 1 00 1010 dfff ffff Z 2
IORWF f, d Inclusive OR W with f 1 00 0100 dfff ffff Z 2
MOVF f, d Move f 1 00 1000 dfff ffff Z 2
MOVWF f Move W to f 1 00 0000 1fff ffff 2
RLF f, d Rotate Left f through Carry 1 00 1101 dfff ffff C 2
RRF f, d Rotate Right f through Carry 1 00 1100 dfff ffff C 2
SUBWF f, d Subtract W from f 1 00 0010 dfff ffff C, DC, Z 2
SUBWFB f, d Subtract with Borrow W from f 1 11 1011 dfff ffff C, DC, Z 2
SWAPF f, d Swap nibbles in f 1 00 1110 dfff ffff 2
XORWF f, d Exclusive OR W with f 1 00 0110 dfff ffff Z 2
BYTE ORIENTED SKIP OPERATIONS

DECFSZ f, d Decrement f, Skip if 0 1(2) 00 1011 dfff ffff 1, 2


INCFSZ f, d Increment f, Skip if 0 1(2) 00 1111 dfff ffff 1, 2

BIT-ORIENTED FILE REGISTER OPERATIONS

BCF f, b Bit Clear f 1 01 00bb bfff ffff 2


BSF f, b Bit Set f 1 01 01bb bfff ffff 2

BIT-ORIENTED SKIP OPERATIONS


BTFSC f, b Bit Test f, Skip if Clear 1 (2) 01 10bb bfff ffff 1, 2
BTFSS f, b Bit Test f, Skip if Set 1 (2) 01 11bb bfff ffff 1, 2
LITERAL OPERATIONS
ADDLW k Add literal and W 1 11 1110 kkkk kkkk C, DC, Z
ANDLW k AND literal with W 1 11 1001 kkkk kkkk Z
IORLW k Inclusive OR literal with W 1 11 1000 kkkk kkkk Z
MOVLB k Move literal to BSR 1 00 0000 001k kkkk
MOVLP k Move literal to PCLATH 1 11 0001 1kkk kkkk
MOVLW k Move literal to W 1 11 0000 kkkk kkkk
SUBLW k Subtract W from literal 1 11 1100 kkkk kkkk C, DC, Z
XORLW k Exclusive OR literal with W 1 11 1010 kkkk kkkk Z
Note 1: If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
2: If this instruction addresses an INDF register and the MSb of the corresponding FSR is set, this instruction will require
one additional instruction cycle.

 2016-2018 Microchip Technology Inc. DS40001866B-page 503


PIC16(L)F15356/75/76/85/86
TABLE 36-3: INSTRUCTION SET (CONTINUED)
Mnemonic, 14-Bit Opcode Status
Description Cycles Notes
Operands MSb LSb Affected

CONTROL OPERATIONS
BRA k Relative Branch 2 11 001k kkkk kkkk
BRW – Relative Branch with W 2 00 0000 0000 1011
CALL k Call Subroutine 2 10 0kkk kkkk kkkk
CALLW – Call Subroutine with W 2 00 0000 0000 1010
GOTO k Go to address 2 10 1kkk kkkk kkkk
RETFIE k Return from interrupt 2 00 0000 0000 1001
RETLW k Return with literal in W 2 11 0100 kkkk kkkk
RETURN – Return from Subroutine 2 00 0000 0000 1000
INHERENT OPERATIONS
CLRWDT – Clear Watchdog Timer 1 00 0000 0110 0100 TO, PD
NOP – No Operation 1 00 0000 0000 0000
RESET – Software device Reset 1 00 0000 0000 0001
SLEEP – Go into Standby or IDLE mode 1 00 0000 0110 0011 TO, PD
TRIS f Load TRIS register with W 1 00 0000 0110 0fff
C-COMPILER OPTIMIZED
ADDFSR n, k Add Literal k to FSRn 1 11 0001 0nkk kkkk
MOVIW n mm Move Indirect FSRn to W with pre/post inc/dec 1 00 0000 0001 0nmm Z 2, 3
modifier, mm
k[n] Move INDFn to W, Indexed Indirect. 1 11 1111 0nkk kkkk Z 2
MOVWI n mm Move W to Indirect FSRn with pre/post inc/dec 1 00 0000 0001 1nmm 2, 3
modifier, mm
k[n] Move W to INDFn, Indexed Indirect. 1 11 1111 1nkk kkkk 2
Note 1:If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second cycle
is executed as a NOP.
2: If this instruction addresses an INDF register and the MSb of the corresponding FSR is set, this instruction will require
one additional instruction cycle.
3: See Section 36.3 “Instruction Descriptions” for detailed MOVIW and MOVWI instruction descriptions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 504


PIC16(L)F15356/75/76/85/86
36.3 Instruction Descriptions

ADDFSR Add Literal to FSRn ANDLW AND literal with W


Syntax: [ label ] ADDFSR FSRn, k Syntax: [ label ] ANDLW k
Operands: -32  k  31 Operands: 0  k  255
n  [ 0, 1]
Operation: (W) .AND. (k)  (W)
Operation: FSR(n) + k  FSR(n) Status Affected: Z
Status Affected: None
Description: The contents of W register are
Description: The signed 6-bit literal ‘k’ is added to AND’ed with the 8-bit literal ‘k’. The
the contents of the FSRnH:FSRnL result is placed in the W register.
register pair.

FSRn is limited to the range 0000h-


FFFFh. Moving beyond these bounds
will cause the FSR to wrap-around.

ADDLW Add literal and W


ANDWF AND W with f
Syntax: [ label ] ADDLW k
Syntax: [ label ] ANDWF f,d
Operands: 0  k  255
Operands: 0  f  127
Operation: (W) + k  (W) d 0,1
Status Affected: C, DC, Z Operation: (W) .AND. (f)  (destination)
Description: The contents of the W register are Status Affected: Z
added to the 8-bit literal ‘k’ and the
Description: AND the W register with register ‘f’. If
result is placed in the W register.
‘d’ is ‘0’, the result is stored in the W
register. If ‘d’ is ‘1’, the result is stored
back in register ‘f’.

ADDWF Add W and f ASRF Arithmetic Right Shift


Syntax: [ label ] ADDWF f,d Syntax: [ label ] ASRF f {,d}
Operands: 0  f  127 Operands: 0  f  127
d 0,1 d [0,1]
Operation: (W) + (f)  (destination) Operation: (f<7>) dest<7>
Status Affected: C, DC, Z (f<7:1>)  dest<6:0>,
(f<0>)  C,
Description: Add the contents of the W register
with register ‘f’. If ‘d’ is ‘0’, the result is Status Affected: C, Z
stored in the W register. If ‘d’ is ‘1’, the Description: The contents of register ‘f’ are shifted
result is stored back in register ‘f’. one bit to the right through the Carry
flag. The MSb remains unchanged. If
‘d’ is ‘0’, the result is placed in W. If ‘d’
is ‘1’, the result is stored back in
register ‘f’.
ADDWFC ADD W and CARRY bit to f
register f C
Syntax: [ label ] ADDWFC f {,d}
Operands: 0  f  127
d [0,1]
Operation: (W) + (f) + (C)  dest
Status Affected: C, DC, Z
Description: Add W, the Carry flag and data mem-
ory location ‘f’. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed in data memory location ‘f’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 505


PIC16(L)F15356/75/76/85/86

BCF Bit Clear f BTFSC Bit Test f, Skip if Clear

Syntax: [ label ] BCF f,b Syntax: [ label ] BTFSC f,b

Operands: 0  f  127 Operands: 0  f  127


0b7 0b7

Operation: 0  (f<b>) Operation: skip if (f<b>) = 0

Status Affected: None Status Affected: None

Description: Bit ‘b’ in register ‘f’ is cleared. Description: If bit ‘b’ in register ‘f’ is ‘1’, the next
instruction is executed.
If bit ‘b’, in register ‘f’, is ‘0’, the next
instruction is discarded, and a NOP is
executed instead, making this a 2-
cycle instruction.

BRA Relative Branch


BTFSS Bit Test f, Skip if Set
Syntax: [ label ] BRA label
Syntax: [ label ] BTFSS f,b
[ label ] BRA $+k
Operands: 0  f  127
Operands: -256  label - PC + 1  255
0b<7
-256  k  255
Operation: skip if (f<b>) = 1
Operation: (PC) + 1 + k  PC
Status Affected: None
Status Affected: None
Description: If bit ‘b’ in register ‘f’ is ‘0’, the next
Description: Add the signed 9-bit literal ‘k’ to the
instruction is executed.
PC. Since the PC will have
If bit ‘b’ is ‘1’, then the next instruction
incremented to fetch the next
is discarded and a NOP is executed
instruction, the new address will be
instead, making this a 2-cycle
PC + 1 + k. This instruction is a 2-
instruction.
cycle instruction. This branch has a
limited range.

BRW Relative Branch with W


Syntax: [ label ] BRW
Operands: None
Operation: (PC) + (W)  PC
Status Affected: None
Description: Add the contents of W (unsigned) to
the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 1 + (W). This instruction is a 2-
cycle instruction.

BSF Bit Set f


Syntax: [ label ] BSF f,b
Operands: 0  f  127
0b7
Operation: 1  (f<b>)
Status Affected: None
Description: Bit ‘b’ in register ‘f’ is set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 506


PIC16(L)F15356/75/76/85/86

CALL Call Subroutine CLRWDT Clear Watchdog Timer


Syntax: [ label ] CALL k Syntax: [ label ] CLRWDT
Operands: 0  k  2047 Operands: None
Operation: (PC)+ 1 TOS, Operation: 00h  WDT
k  PC<10:0>, 0  WDT prescaler,
(PCLATH<6:3>)  PC<14:11> 1  TO
Status Affected: None 1  PD
Description: Call Subroutine. First, return address Status Affected: TO, PD
(PC + 1) is pushed onto the stack. Description: CLRWDT instruction resets the Watch-
The 11-bit immediate address is dog Timer. It also resets the prescaler
loaded into PC bits <10:0>. The upper of the WDT. Status bits TO and PD
bits of the PC are loaded from are set.
PCLATH. CALL is a 2-cycle
instruction.

CALLW Subroutine Call With W COMF Complement f


Syntax: [ label ] CALLW
Syntax: [ label ] COMF f,d
Operands: None
Operands: 0  f  127
Operation: (PC) +1  TOS, d  [0,1]
(W)  PC<7:0>, Operation: (f)  (destination)
(PCLATH<6:0>) PC<14:8>
Status Affected: Z
Status Affected: None Description: The contents of register ‘f’ are
complemented. If ‘d’ is ‘0’, the result is
Description: Subroutine call with W. First, the stored in W. If ‘d’ is ‘1’, the result is
return address (PC + 1) is pushed
stored back in register ‘f’.
onto the return stack. Then, the
contents of W is loaded into PC<7:0>,
and the contents of PCLATH into
PC<14:8>. CALLW is a 2-cycle
instruction.

DECF Decrement f
CLRF Clear f
Syntax: [ label ] DECF f,d
Syntax: [ label ] CLRF f
Operands: 0  f  127
Operands: 0  f  127
d  [0,1]
Operation: 00h  (f) Operation: (f) - 1  (destination)
1Z
Status Affected: Z
Status Affected: Z
Description: Decrement register ‘f’. If ‘d’ is ‘0’, the
Description: The contents of register ‘f’ are cleared
result is stored in the W register. If ‘d’
and the Z bit is set. is ‘1’, the result is stored back in
register ‘f’.
CLRW Clear W
Syntax: [ label ] CLRW
Operands: None
Operation: 00h  (W)
1Z
Status Affected: Z
Description: W register is cleared. Zero bit (Z) is
set.

 2016-2018 Microchip Technology Inc. DS40001866B-page 507


PIC16(L)F15356/75/76/85/86

DECFSZ Decrement f, Skip if 0 INCFSZ Increment f, Skip if 0


Syntax: [ label ] DECFSZ f,d Syntax: [ label ] INCFSZ f,d
Operands: 0  f  127 Operands: 0  f  127
d  [0,1] d  [0,1]
Operation: (f) - 1  (destination); Operation: (f) + 1  (destination),
skip if result = 0 skip if result = 0
Status Affected: None Status Affected: None
Description: The contents of register ‘f’ are decre- Description: The contents of register ‘f’ are incre-
mented. If ‘d’ is ‘0’, the result is placed mented. If ‘d’ is ‘0’, the result is placed
in the W register. If ‘d’ is ‘1’, the result in the W register. If ‘d’ is ‘1’, the result
is placed back in register ‘f’. is placed back in register ‘f’.
If the result is ‘1’, the next instruction is If the result is ‘1’, the next instruction is
executed. If the result is ‘0’, then a executed. If the result is ‘0’, a NOP is
NOP is executed instead, making it a executed instead, making it a 2-cycle
2-cycle instruction. instruction.

GOTO Unconditional Branch IORLW Inclusive OR literal with W


Syntax: [ label ] GOTO k Syntax: [ label ] IORLW k
Operands: 0  k  2047 Operands: 0  k  255
Operation: k  PC<10:0> Operation: (W) .OR. k  (W)
PCLATH<6:3>  PC<14:11>
Status Affected: Z
Status Affected: None Description: The contents of the W register are
Description: GOTO is an unconditional branch. The OR’ed with the 8-bit literal ‘k’. The
11-bit immediate value is loaded into result is placed in the W register.
PC bits <10:0>. The upper bits of PC
are loaded from PCLATH<4:3>. GOTO
is a 2-cycle instruction.

INCF Increment f IORWF Inclusive OR W with f


Syntax: [ label ] INCF f,d Syntax: [ label ] IORWF f,d
Operands: 0  f  127 Operands: 0  f  127
d  [0,1] d  [0,1]
Operation: (f) + 1  (destination) Operation: (W) .OR. (f)  (destination)
Status Affected: Z Status Affected: Z
Description: The contents of register ‘f’ are incre- Description: Inclusive OR the W register with regis-
mented. If ‘d’ is ‘0’, the result is placed ter ‘f’. If ‘d’ is ‘0’, the result is placed in
in the W register. If ‘d’ is ‘1’, the result the W register. If ‘d’ is ‘1’, the result is
is placed back in register ‘f’. placed back in register ‘f’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 508


PIC16(L)F15356/75/76/85/86

LSLF Logical Left Shift MOVF Move f


Syntax: [ label ] LSLF f {,d} Syntax: [ label ] MOVF f,d
Operands: 0  f  127 Operands: 0  f  127
d [0,1] d  [0,1]
Operation: (f<7>)  C Operation: (f)  (dest)
(f<6:0>)  dest<7:1> Status Affected: Z
0  dest<0>
Description: The contents of register f is moved to
Status Affected: C, Z a destination dependent upon the
Description: The contents of register ‘f’ are shifted status of d. If d = 0, destination is W
one bit to the left through the Carry flag. register. If d = 1, the destination is file
A ‘0’ is shifted into the LSb. If ‘d’ is ‘0’, register f itself. d = 1 is useful to test a
the result is placed in W. If ‘d’ is ‘1’, the file register since status flag Z is
result is stored back in register ‘f’. affected.

C register f 0 Words: 1
Cycles: 1
Example: MOVF FSR, 0
After Instruction
LSRF Logical Right Shift
W = value in FSR register
Syntax: [ label ] LSRF f {,d} Z = 1
Operands: 0  f  127
d [0,1]
Operation: 0  dest<7>
(f<7:1>)  dest<6:0>,
(f<0>)  C,
Status Affected: C, Z
Description: The contents of register ‘f’ are shifted
one bit to the right through the Carry
flag. A ‘0’ is shifted into the MSb. If ‘d’ is
‘0’, the result is placed in W. If ‘d’ is ‘1’,
the result is stored back in register ‘f’.

0 register f C

 2016-2018 Microchip Technology Inc. DS40001866B-page 509


PIC16(L)F15356/75/76/85/86

MOVIW Move INDFn to W MOVLP Move literal to PCLATH


Syntax: [ label ] MOVIW ++FSRn Syntax: [ label ] MOVLP k
[ label ] MOVIW --FSRn
Operands: 0  k  127
[ label ] MOVIW FSRn++
[ label ] MOVIW FSRn-- Operation: k  PCLATH
[ label ] MOVIW k[FSRn] Status Affected: None
Operands: n  [0,1] Description: The 7-bit literal ‘k’ is loaded into the
mm  [00,01, 10, 11] PCLATH register.
-32  k  31
Operation: INDFn  W
Effective address is determined by MOVLW Move literal to W
• FSR + 1 (preincrement)
• FSR - 1 (predecrement) Syntax: [ label ] MOVLW k
• FSR + k (relative offset) Operands: 0  k  255
After the Move, the FSR value will be Operation: k  (W)
either:
• FSR + 1 (all increments) Status Affected: None
• FSR - 1 (all decrements) Description: The 8-bit literal ‘k’ is loaded into W reg-
• Unchanged ister. The “don’t cares” will assemble as
Status Affected: Z ‘0’s.
Words: 1

Mode Syntax mm Cycles: 1

Preincrement ++FSRn 00 Example: MOVLW 0x5A


Predecrement --FSRn 01 After Instruction
W = 0x5A
Postincrement FSRn++ 10
Postdecrement FSRn-- 11
MOVWF Move W to f
Syntax: [ label ] MOVWF f
Description: This instruction is used to move data
between W and one of the indirect Operands: 0  f  127
registers (INDFn). Before/after this Operation: (W)  (f)
move, the pointer (FSRn) is updated by
pre/post incrementing/decrementing it. Status Affected: None
Description: Move data from W register to register
Note: The INDFn registers are not ‘f’.
physical registers. Any instruction that
Words: 1
accesses an INDFn register actually
accesses the register at the address Cycles: 1
specified by the FSRn. Example: MOVWF LATA
Before Instruction
FSRn is limited to the range 0000h -
FFFFh. Incrementing/decrementing it LATA = 0xFF
W = 0x4F
beyond these bounds will cause it to
After Instruction
wrap-around.
LATA = 0x4F
W = 0x4F
MOVLB Move literal to BSR
Syntax: [ label ] MOVLB k
Operands: 0k
Operation: k  BSR
Status Affected: None
Description: The 6-bit literal ‘k’ is loaded into the
Bank Select Register (BSR).

 2016-2018 Microchip Technology Inc. DS40001866B-page 510


PIC16(L)F15356/75/76/85/86

MOVWI Move W to INDFn NOP No Operation


Syntax: [ label ] NOP
Syntax: [ label ] MOVWI ++FSRn
[ label ] MOVWI --FSRn Operands: None
[ label ] MOVWI FSRn++
Operation: No operation
[ label ] MOVWI FSRn--
[ label ] MOVWI k[FSRn] Status Affected: None

Operands: n  [0,1] Description: No operation.


mm  [00,01, 10, 11] Words: 1
-32  k  31
Cycles: 1
Operation: W  INDFn
Example: NOP
Effective address is determined by
• FSR + 1 (preincrement)
• FSR - 1 (predecrement)
• FSR + k (relative offset)
After the Move, the FSR value will be
either:
RESET Software Reset
• FSR + 1 (all increments) Syntax: [ label ] RESET
• FSR - 1 (all decrements)
Unchanged Operands: None
Operation: Execute a device Reset. Resets the
Status Affected: None
RI flag of the PCON register.
Status Affected: None
Mode Syntax mm
Description: This instruction provides a way to
Preincrement ++FSRn 00 execute a hardware Reset by
Predecrement --FSRn 01 software.

Postincrement FSRn++ 10
Postdecrement FSRn-- 11
RETFIE Return from Interrupt
Syntax: [ label ] RETFIE k
Description: This instruction is used to move data
between W and one of the indirect Operands: None
registers (INDFn). Before/after this Operation: TOS  PC,
move, the pointer (FSRn) is updated by 1  GIE
pre/post incrementing/decrementing it.
Status Affected: None

Note: The INDFn registers are not Description: Return from Interrupt. Stack is POPed
physical registers. Any instruction that and Top-of-Stack (TOS) is loaded in
accesses an INDFn register actually the PC. Interrupts are enabled by
accesses the register at the address setting Global Interrupt Enable bit,
specified by the FSRn. GIE (INTCON<7>). This is a 2-cycle
instruction.
FSRn is limited to the range 0000h- Words: 1
FFFFh. Incrementing/decrementing it
Cycles: 2
beyond these bounds will cause it to
wrap-around. Example: RETFIE
After Interrupt
The increment/decrement operation on
PC = TOS
FSRn WILL NOT affect any Status bits. GIE = 1

 2016-2018 Microchip Technology Inc. DS40001866B-page 511


PIC16(L)F15356/75/76/85/86

RETLW Return with literal in W RLF Rotate Left f through Carry


Syntax: [ label ] RLF f,d
Syntax: [ label ] RETLW k
Operands: 0  f  127
Operands: 0  k  255
d  [0,1]
Operation: k  (W);
Operation: See description below
TOS  PC
Status Affected: None Status Affected: C
Description: The contents of register ‘f’ are rotated
Description: The W register is loaded with the 8-bit
literal ‘k’. The program counter is one bit to the left through the Carry
flag. If ‘d’ is ‘0’, the result is placed in
loaded from the top of the stack (the
the W register. If ‘d’ is ‘1’, the result is
return address). This is a 2-cycle
instruction. stored back in register ‘f’.
C Register f
Words: 1
Cycles: 2
Words: 1
Example: CALL TABLE;W contains table
Cycles: 1
;offset value
• ;W now has table value Example: RLF REG1,0
TABLE • Before Instruction
• REG1 = 1110 0110
ADDWF PC ;W = offset C = 0
RETLW k1 ;Begin table After Instruction
RETLW k2 ; REG1 = 1110 0110
• W = 1100 1100
• C = 1

RETLW kn ; End of table
RRF Rotate Right f through Carry
Before Instruction
W = 0x07 Syntax: [ label ] RRF f,d
After Instruction Operands: 0  f  127
W = value of k8 d  [0,1]
Operation: See description below

RETURN Return from Subroutine Status Affected: C


Description: The contents of register ‘f’ are rotated
Syntax: [ label ] RETURN one bit to the right through the Carry
Operands: None flag. If ‘d’ is ‘0’, the result is placed in
Operation: TOS  PC the W register. If ‘d’ is ‘1’, the result is
placed back in register ‘f’.
Status Affected: None
C Register f
Description: Return from subroutine. The stack is
POPed and the top of the stack (TOS)
is loaded into the program counter.
This is a 2-cycle instruction.

 2016-2018 Microchip Technology Inc. DS40001866B-page 512


PIC16(L)F15356/75/76/85/86

SUBWF Subtract W from f

SLEEP Enter Sleep mode Syntax: [ label ] SUBWF f,d


Syntax: [ label ] SLEEP Operands: 0 f 127
d  [0,1]
Operands: None
Operation: (f) - (W) destination)
Operation: 00h  WDT,
0  WDT prescaler, Status Affected: C, DC, Z
1  TO, Description: Subtract (2’s complement method) W
0  PD register from register ‘f’. If ‘d’ is ‘0’, the
Status Affected: TO, PD result is stored in the W
register. If ‘d’ is ‘1’, the result is stored
Description: The power-down Status bit, PD is back in register ‘f.
cleared. Time-out Status bit, TO is
set. Watchdog Timer and its C=0 Wf
prescaler are cleared.
See Section 11.2 “Sleep Mode” for C=1 Wf
more information. DC = 0 W<3:0>  f<3:0>
DC = 1 W<3:0>  f<3:0>

SUBWFB Subtract W from f with Borrow


Syntax: SUBWFB f {,d}
Operands: 0  f  127
d  [0,1]
Operation: (f) – (W) – (B) dest
Status Affected: C, DC, Z
Description: Subtract W and the BORROW flag
(CARRY) from register ‘f’ (2’s
complement method). If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
SUBLW Subtract W from literal result is stored back in register ‘f’.

Syntax: [ label ] SUBLW k


Operands: 0 k 255 SWAPF Swap Nibbles in f
Operation: k - (W) W)
Syntax: [ label ] SWAPF f,d
Status Affected: C, DC, Z
Operands: 0  f  127
Description: The W register is subtracted (2’s d  [0,1]
complement method) from the 8-bit
Operation: (f<3:0>)  (destination<7:4>),
literal ‘k’. The result is placed in the W
(f<7:4>)  (destination<3:0>)
register.
Status Affected: None
C=0 Wk Description: The upper and lower nibbles of
C=1 Wk register ‘f’ are exchanged. If ‘d’ is ‘0’,
the result is placed in the W register. If
DC = 0 W<3:0>  k<3:0>
‘d’ is ‘1’, the result is placed in register
DC = 1 W<3:0>  k<3:0> ‘f’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 513


PIC16(L)F15356/75/76/85/86

TRIS Load TRIS Register with W XORLW Exclusive OR literal with W


Syntax: [ label ] TRIS f Syntax: [ label ] XORLW k
Operands: 5f7 Operands: 0 k 255
Operation: (W)  TRIS register ‘f’ Operation: (W) .XOR. k W)
Status Affected: None Status Affected: Z
Description: Move data from W register to TRIS Description: The contents of the W register are
register. XOR’ed with the 8-bit literal ‘k’. The
When ‘f’ = 5, TRISA is loaded. result is placed in the W register.
When ‘f’ = 6, TRISB is loaded.
When ‘f’ = 7, TRISC is loaded.

XORWF Exclusive OR W with f


Syntax: [ label ] XORWF f,d
Operands: 0  f  127
d  [0,1]
Operation: (W) .XOR. (f) destination)
Status Affected: Z
Description: Exclusive OR the contents of the W
register with register ‘f’. If ‘d’ is ‘0’, the
result is stored in the W register. If ‘d’
is ‘1’, the result is stored back in
register ‘f’.

 2016-2018 Microchip Technology Inc. DS40001866B-page 514


PIC16(L)F15356/75/76/85/86
37.0 ELECTRICAL SPECIFICATIONS
37.1 Absolute Maximum Ratings(†)
Ambient temperature under bias...................................................................................................... -40°C to +125°C
Storage temperature ........................................................................................................................ -65°C to +150°C
Voltage on pins with respect to VSS
on VDD pin
PIC16F15356/75/76/85/86 ........................................................................................ -0.3V to +6.5V
PIC16LF15356/75/76/85/86 ...................................................................................... -0.3V to +4.0V
on MCLR pin ........................................................................................................................... -0.3V to +9.0V
on all other pins ............................................................................................................ -0.3V to (VDD + 0.3V)
Maximum current
on VSS pin(1)
-40°C  TA  +85°C .............................................................................................................. 350 mA
85°C  TA  +125°C ............................................................................................................. 120 mA
on VDD pin for 28-Pin devices(1)
-40°C  TA  +85°C .............................................................................................................. 250 mA
85°C  TA  +125°C ............................................................................................................... 85 mA
on VDD pin for 40-Pin devices(1)
-40°C  TA  +85°C .............................................................................................................. 350 mA
85°C  TA  +125°C ............................................................................................................. 120 mA
on any standard I/O pin ...................................................................................................................... 50 mA
Clamp current, IK (VPIN < 0 or VPIN > VDD) ................................................................................................... 20 mA
Total power dissipation(2)................................................................................................................................ 800 mW

Note 1: Maximum current rating requires even load distribution across I/O pins. Maximum current rating may be
limited by the device package power dissipation characterizations, see Table 37-6 to calculate device
specifications.
2: Power dissipation is calculated as follows:
PDIS = VDD x {IDD - IOH} + VDD - VOH) x IOH} + VOI x IOL

† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure above maximum rating conditions for
extended periods may affect device reliability.

 2016-2018 Microchip Technology Inc. DS40001866B-page 515


PIC16(L)F15356/75/76/85/86
37.2 Standard Operating Conditions
The standard operating conditions for any device are defined as:
Operating Voltage: VDDMIN VDD VDDMAX
Operating Temperature: TA_MIN TA TA_MAX
VDD — Operating Supply Voltage(1)
PIC16LF15356/75/76/85/86
VDDMIN (Fosc  16 MHz) ......................................................................................................... +1.8V
VDDMIN (Fosc  32 MHz) ......................................................................................................... +2.5V
VDDMAX .................................................................................................................................... +3.6V
PIC16F15356/75/76/85/86
VDDMIN (Fosc  16 MHz) ......................................................................................................... +2.3V
VDDMIN (Fosc  32 MHz) ......................................................................................................... +2.5V
VDDMAX .................................................................................................................................... +5.5V
TA — Operating Ambient Temperature Range
Industrial Temperature
TA_MIN ...................................................................................................................................... -40°C
TA_MAX .................................................................................................................................... +85°C
Extended Temperature
TA_MIN ...................................................................................................................................... -40°C
TA_MAX .................................................................................................................................. +125°C
Note 1: See Parameter Supply Voltage, DS Characteristics: Supply Voltage.

 2016-2018 Microchip Technology Inc. DS40001866B-page 516


PIC16(L)F15356/75/76/85/86
FIGURE 37-1: VOLTAGE FREQUENCY GRAPH, -40°C  TA +125°C, PIC16F15356/75/76/85/86
ONLY

5.5
VDD (V)

2.5

2.3

0 4 10 16 32
Frequency (MHz)

Note 1:The shaded region indicates the permissible combinations of voltage and frequency.
2: Refer to Table 37-7 for each Oscillator mode’s supported frequencies.

FIGURE 37-2: VOLTAGE FREQUENCY GRAPH, -40°C  TA +125°C, PIC16LF15356/75/76/85/86


ONLY
VDD (V)

3.6

2.5

1.8

0 4 10 16 32
Frequency (MHz)

Note 1:The shaded region indicates the permissible combinations of voltage and frequency.
2: Refer to Table 37-7 for each Oscillator mode’s supported frequencies.

 2016-2018 Microchip Technology Inc. DS40001866B-page 517


PIC16(L)F15356/75/76/85/86
37.3 DC Characteristics
TABLE 37-1: SUPPLY VOLTAGE
PIC16LF15356/75/76/85/86 Standard Operating Conditions (unless otherwise stated)

PIC16F15356/75/76/85/86 Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ.† Max. Units Conditions
No.
Supply Voltage
D002 VDD 1.8 — 3.6 V FOSC  16 MHz
2.5 — 3.6 V FOSC  16 MHz
D002 VDD 2.3 — 5.5 V FOSC  16 MHz
2.5 — 5.5 V FOSC 16 MHz
RAM Data Retention(1)
D003 VDR 1.5 — — V Device in Sleep mode
D003 VDR 1.7 — — V Device in Sleep mode
Power-on Reset Release Voltage(2)
D004 VPOR — 1.6 — V BOR or LPBOR disabled(3)
D004 VPOR — 1.6 — V BOR or LPBOR disabled(3)
Power-on Reset Rearm Voltage(2)
D005 VPORR — 0.8 — V BOR or LPBOR disabled(3)
D005 VPORR — 1.5 — V BOR or LPBOR disabled(3)
VDD Rise Rate to ensure internal Power-on Reset signal(2)
D006 SVDD 0.05 — — V BOR or LPBOR disabled(3)
D006 SVDD 0.05 — — V BOR or LPBOR disabled(3)
† Data in “Typ.” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.
2: See Figure 37-3, POR and POR REARM with Slow Rising VDD.
3: See Table 37-11 for BOR and LPBOR trip point information.
4: = F device

 2016-2018 Microchip Technology Inc. DS40001866B-page 518


PIC16(L)F15356/75/76/85/86
FIGURE 37-3: POR AND POR REARM WITH SLOW RISING VDD

VDD

VPOR
VPORR
SVDD

VSS
NPOR(1)

POR REARM

VSS

TVLOW(3) TPOR(2)

Note 1: When NPOR is low, the device is held in Reset.


2: TPOR 1 s typical.
3: TVLOW 2.7 s typical.

 2016-2018 Microchip Technology Inc. DS40001866B-page 519


PIC16(L)F15356/75/76/85/86

TABLE 37-2: SUPPLY CURRENT (IDD)(1,2,4)


Standard Operating Conditions (unless otherwise
PIC16LF15356/75/76/85/86
stated)

PIC16F15356/75/76/85/86

Param. Conditions
Symbol Device Characteristics Min. Typ.† Max. Units
No. VDD Note
D100 IDDXT4 XT = 4 MHz — 360 470 A 3.0V
D100 IDDXT4 XT = 4 MHz — 380 480 A 3.0V
D101 IDDHFO16 HFINTOSC = 16 MHz — 1.4 2.3 mA 3.0V
D101 IDDHFO16 HFINTOSC = 16 MHz — 1.5 2.3 mA 3.0V
D102 IDDHFOPLL HFINTOSC = 32 MHz — 2.6 3.6 mA 3.0V 32 MHz PIC16
D102 IDDHFOPLL HFINTOSC = 32 MHz — 2.7 3.7 mA 3.0V 32 MHz PIC16
D103 IDDHSPLL32 HS+PLL = 32 MHz — 2.6 3.6 mA 3.0V 32 MHz PIC16
D103 IDDHSPLL32 HS+PLL = 32 MHz — 2.7 3.7 mA 3.0V 32 MHz PIC16
D104 IDDIDLE IDLE mode, HFINTOSC = 16 MHz — 0.8 1.1 mA 3.0V
D104 IDDIDLE IDLE mode, HFINTOSC = 16 MHz — 0.8 1.2 mA 3.0V
D105 IDDDOZE(3) DOZE mode, HFINTOSC = 16 MHz, Doze — 795 — A 3.0V Typical value only.
Ratio = 16
D105 IDDDOZE(3) DOZE mode, HFINTOSC = 16 MHz, Doze — 800 — A 3.0V Typical value only.
Ratio = 16
† Data in “Typ.” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins are outputs driven low; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: IDDDOZE = [IDDIDLE*(N-1)/N] + IDDHFO16/N where N = DOZE Ratio (Register 11-2).
4: PMD bits are all in the default state, no modules are disabled.
5: = F device

 2016-2018 Microchip Technology Inc. DS40001866B-page 520


PIC16(L)F15356/75/76/85/86

TABLE 37-3: POWER-DOWN CURRENT (IPD)(1,2,3)


PIC16LF15356/75/76/85/86 Standard Operating Conditions (unless otherwise stated)

Standard Operating Conditions (unless otherwise stated)


PIC16F15356/75/76/85/86
VREGPM = 1

Param. Max. Max. Conditions


Symbol Device Characteristics Min. Typ.† Units
No. +85°C +125°C VDD Note
D200 IPD IPD Base — 0.05 2 6 A 3.0V

D200 IPD IPD Base — 0.4 2.5 9 A 3.0V


D200A — 18 22 27 A 3.0V VREGPM = 0
D201 IPD_WDT Low-Frequency Internal Oscillator/ — 0.4 2.9 9 A 3.0V
WDT
D201 IPD_WDT Low-Frequency Internal Oscillator/ — 0.5 3.3 13 A 3.0V
WDT
D202 IPD_SOSC Secondary Oscillator (SOSC) — 0.6 2.8 13 A 3.0V
D202 IPD_SOSC Secondary Oscillator (SOSC) — 0.8 3.2 15 A 3.0V
D203 IPD_FVR FVR — 45 74 76 A 3.0V
D203 IPD_FVR FVR — 40 70 75 A 3.0V
D204 IPD_BOR Brown-out Reset (BOR) — 10 17 19 A 3.0V
D204 IPD_BOR Brown-out Reset (BOR) — 14 18 20 A 3.0V
D205 IPD_LPBOR Low-Power Brown-out Reset (LPBOR) — 0.5 4 10 A 3.0V
D205 IPD_LPBOR Low-Power Brown-out Reset (LPBOR) 0.7 5 11 A 3.0V
D206 IPD_ADCA ADC - Active — 250 — — A 3.0V ADC is converting (4)
D206 IPD_ADCA ADC - Active — 280 — — A 3.0V ADC is converting (4)
D207 IPD_CMP Comparator — 30 90 93 A 3.0V
D207 IPD_CMP Comparator — 33 93 98 A 3.0V
† Data in “Typ.” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The peripheral current is the sum of the base IDD and the additional current consumed when this peripheral is enabled. The
peripheral ∆ current can be determined by subtracting the base IDD or IPD current from this limit. Max. values should be used
when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part
in Sleep mode with all I/O pins in high-impedance state and tied to VSS.
3: All peripheral currents listed are on a per-peripheral basis if more than one instance of a peripheral is available.
4: ADC clock source is FRC.
5: = F device

 2016-2018 Microchip Technology Inc. DS40001866B-page 521


PIC16(L)F15356/75/76/85/86

TABLE 37-4: I/O PORTS


Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
VIL Input Low Voltage
I/O PORT:
D300 with TTL buffer — — 0.8 V 4.5V  VDD  5.5V
D301 — — 0.15 VDD V 1.8V  VDD  4.5V
D302 with Schmitt Trigger buffer — — 0.2 VDD V 2.0V  VDD  5.5V
D303 with I2C levels — — 0.3 VDD V
D304 with SMBus levels — — 0.8 V 2.7V  VDD  5.5V
D305 MCLR — — 0.2 VDD V
VIH Input High Voltage
I/O PORT:
D320 with TTL buffer 2 — — V 4.5V  VDD 5.5V
D321 0.25 VDD + — — V 1.8V  VDD  4.5V
0.8
D322 with Schmitt Trigger buffer 0.8 VDD — — V 2.0V  VDD  5.5V
D323 with I2C levels 0.7 VDD — — V
D324 with SMBus levels 2.1 — — V 2.7V  VDD  5.5V
D325 MCLR 0.7 VDD — — V
IIL Input Leakage Current(1)
D340 I/O Ports — ±5 ± 125 nA VSS  VPIN  VDD,
Pin at high-impedance, 85°C
D341 — ±5 ± 1000 nA VSS  VPIN  VDD,
Pin at high-impedance, 125°C
D342 MCLR(2) — ± 50 ± 200 nA VSS  VPIN  VDD,
Pin at high-impedance, 85°C
IPUR Weak Pull-up Current
D350 25 100 200 A VDD = 3.0V, VPIN = VSS
VOL Output Low Voltage
D360 I/O ports — — 0.6 V IOL = 10.0 mA, VDD = 3.0V
VOH Output High Voltage
D370 I/O ports VDD - 0.7 — — V IOH = 6.0 mA, VDD = 3.0V
D380 CIO All I/O pins — 5 50 pF
†Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:Negative current is defined as current sourced by the pin.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.

 2016-2018 Microchip Technology Inc. DS40001866B-page 522


PIC16(L)F15356/75/76/85/86

TABLE 37-5: MEMORY PROGRAMMING SPECIFICATIONS


Standard Operating Conditions (unless otherwise stated)
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
High Voltage Entry Programming Mode Specifications
MEM01 VIHH Voltage on MCLR/VPP pin to enter 8 — 9 V (Note 2, Note 3)
programming mode
MEM02 IPPGM Current on MCLR/VPP pin during — 1 — mA (Note 2)
programming mode
Programming Mode Specifications
MEM10 VBE VDD for Bulk Erase — 2.7 — V
MEM11 IDDPGM Supply Current during Programming — — 10 mA
operation
Program Flash Memory Specifications
MEM30 EP Flash Memory Cell Endurance 10k — — E/W -40C  TA  +85C
(Note 1)
MEM32 TP_RET Characteristic Retention — 40 — Year Provided no other
specifications are violated

MEM33 VP_RD VDD for Read operation VDDMIN — VDDMAX V


MEM34 VP_REW VDD for Row Erase or Write VDDMIN — VDDMAX V
operation
MEM35 TP_REW Self-Timed Row Erase or Self-Timed — 2.0 2.5 ms
Write
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: Flash Memory Cell Endurance for the Flash memory is defined as: One Row Erase operation and one Self-Timed
Write. HEF feature applies only to the last 128 words of the Program Flash Memory.
2: Required only if CONFIG4, bit LVP is disabled.
3: The MPLAB® ICD2 does not support variable VPP output. Circuitry to limit the ICD2 VPP voltage must be placed
between the ICD2 and target system when programming or debugging with the ICD2.

 2016-2018 Microchip Technology Inc. DS40001866B-page 523


PIC16(L)F15356/75/76/85/86
TABLE 37-6: THERMAL CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ TA ≤ +125°C

Param.
Sym. Characteristic Typ. Units Conditions
No.

TH01 JA Thermal Resistance Junction to Ambient 60 C/W 28-pin SPDIP package
80 C/W 28-pin SOIC package
90 C/W 28-pin SSOP package
48 C/W 28-pin UQFN 4x4mm package
47.2 C/W 40-pin PDIP package
41.0 C/W 40-pin UQFN 5x5 package
46.0 C/W 44-pin TQFP package
24.4 C/W 44-pin QFN 8X8mm package
27.6 C/W 48-pin UQFN 6x6 package
— C/W 48-pin TQFP 7x7 package
TH02 JC Thermal Resistance Junction to Case 31.4 C/W 28-pin SPDIP package
24 C/W 28-pin SOIC package
24 C/W 28-pin SSOP package
12 C/W 28-pin UQFN 4x4mm package
24.70 C/W 40-pin PDIP package
5.5 C/W 40-pin UQFN 5x5 package
14.5 C/W 44-pin TQFP package
20.0 C/W 44-pin QFN 8X8mm package
6.7 C/W 48-pin UQFN 6x6 package
— C/W 48-pin TQFP 7x7 package
TH03 TJMAX Maximum Junction Temperature 150 C
TH04 PD Power Dissipation — W PD = PINTERNAL + PI/O
TH05 PINTERNAL Internal Power Dissipation — W PINTERNAL = IDD x VDD(1)
TH06 P I /O I/O Power Dissipation — W PI/O =  (IOL * VOL) +  (IOH * (VDD - VOH))
TH07 PDER Derated Power — W PDER = PDMAX (TJ - TA)/JA(2)
Note 1:IDD is current to run the chip alone without driving any load on the output pins.
2: TA = Ambient Temperature, TJ = Junction Temperature

 2016-2018 Microchip Technology Inc. DS40001866B-page 524


PIC16(L)F15356/75/76/85/86
37.4 AC Characteristics

FIGURE 37-4: LOAD CONDITIONS

Rev. 10-000133A
8/1/2013

Load Condition

Pin

CL

VSS

Legend: CL=50 pF for all pins

 2016-2018 Microchip Technology Inc. DS40001866B-page 525


PIC16(L)F15356/75/76/85/86
FIGURE 37-5: CLOCK TIMING

Q4 Q1 Q2 Q3 Q4 Q1

CLKIN
OS02 OS12 OS11

OS03
CLKOUT
(CLKOUT Mode)

Note 1: See Table 37-7.

TABLE 37-7: EXTERNAL CLOCK/OSCILLATOR TIMING REQUIREMENTS


Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
ECL Oscillator
OS1 FECL Clock Frequency — — 500 kHz
OS2 TECL_DC Clock Duty Cycle 40 — 60 %
ECM Oscillator
OS3 FECM Clock Frequency — — 4 MHz
OS4 TECM_DC Clock Duty Cycle 40 — 60 %
ECH Oscillator
OS5 FECH Clock Frequency — — 32 MHz
OS6 TECH_DC Clock Duty Cycle 40 — 60 %
LP Oscillator
OS7 FLP Clock Frequency — — 100 kHz Note 4
XT Oscillator
OS8 FXT Clock Frequency — — 4 MHz Note 4
HS Oscillator
OS9 FHS Clock Frequency — — 20 MHz
System Oscillator
OS20 FOSC System Clock Frequency — — 32 MHz (Note 2, Note 3)
OS21 FCY Instruction Frequency — FOSC/4 — MHz
OS22 TCY Instruction Period 125 1/FCY — ns
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing
code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected
current consumption. All devices are tested to operate at “min” values with an external clock applied to OSC1 pin.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
2: The system clock frequency (FOSC) is selected by the “main clock switch controls” as described in Section 9.0
“Oscillator Module (with Fail-Safe Clock Monitor)”.
3: The system clock frequency (FOSC) must meet the voltage requirements defined in the Section 37.2 “Standard
Operating Conditions”.
4: LP, XT and HS oscillator modes require an appropriate crystal or resonator to be connected to the device. For clocking
the device with the external square wave, one of the EC mode selections must be used.

 2016-2018 Microchip Technology Inc. DS40001866B-page 526


PIC16(L)F15356/75/76/85/86
TABLE 37-8: INTERNAL OSCILLATOR PARAMETERS(1)
Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
OS50 FHFOSC Precision Calibrated HFINTOSC — 4 — MHz (Note 2)
Frequency 8
12
16
32
OS51 FHFOSCLP Low-Power Optimized HFINTOSC 0.93 1 1.07 MHz
Frequency 1.86 2 2.14 MHz
OS52 FMFOSC Internal Calibrated MFINTOSC — 500 — kHz
Frequency
OS53 FLFOSC Internal LFINTOSC Frequency — 31 — kHz (Note 3)
OS54 THFOSCST HFINTOSC — 11 20 s VREGPM = 0
Wake-up from Sleep Start-up — 50 — s VREGPM = 1
Time
OS56 TLFOSCST LFINTOSC — 0.2 — ms
Wake-up from Sleep Start-up Time
†Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to
the device as possible. 0.1 F and 0.01 F values in parallel are recommended.
2: See Figure 37-6: Precision Calibrated HFINTOSC Frequency Accuracy Over Device VDD and Tempera-
ture.
3: See Figure 38-87: LFINTOSC Frequency, PIC16LF15356/75/76/85/86 devices only and Figure 38-88:
LFINTOSC Frequency, PIC16F15356/75/76/85/86 devices only.

FIGURE 37-6: PRECISION CALIBRATED HFINTOSC FREQUENCY ACCURACY OVER DEVICE


VDD AND TEMPERATURE

125

± 5%

85

± 3%
Temperature (°C)

60

± 2%

0
± 5%

-40
1.8 2.0 2.3 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

 2016-2018 Microchip Technology Inc. DS40001866B-page 527


PIC16(L)F15356/75/76/85/86
TABLE 37-9: PLL SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated) VDD 2.5V
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
PLL01 FPLLIN PLL Input Frequency Range 4 — 8 MHz
PLL02 FPLLOUT PLL Output Frequency Range 16 — 32 MHz Note 1
PLL03 TPLLST PLL Lock Time from Start-up — 200 — s
PLL04 FPLLJIT PLL Output Frequency Stability (Jitter) -0.25 — 0.25 %
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: The output frequency of the PLL must meet the FOSC requirements listed in Parameter D002.

 2016-2018 Microchip Technology Inc. DS40001866B-page 528


PIC16(L)F15356/75/76/85/86
FIGURE 37-7: CLKOUT AND I/O TIMING

Cycle Write Fetch Read Execute


Q4 Q1 Q2 Q3
FOSC
IO1 IO2
IO10
CLKOUT
IO8, IO9 IO5 IO6, IO7
IO4
I/O pin
(Input)
IO3
I/O pin Old Value New Value
(Output)
IO6, IO7, IO8, IO9

TABLE 37-10: I/O AND CLKOUT TIMING SPECIFICATIONS


Standard Operating Conditions (unless otherwise stated)
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
IO1* TCLKOUTH CLKOUT rising edge delay (rising — — 70 ns
edge FOSC (Q1 cycle) to falling edge
CLKOUT
IO2* TCLKOUTL CLKOUT falling edge delay (rising — — 72 ns
edge FOSC (Q3 cycle) to rising edge
CLKOUT
IO3* TIO_VALID Port output valid time (rising edge — 50 70 ns
Fosc (Q1 cycle) to port valid)
IO4* TIO_SETUP Port input setup time (Setup time 20 — — ns
before rising edge Fosc – Q2 cycle)
IO5* TIO_HOLD Port input hold time (Hold time after 50 — — ns
rising edge Fosc – Q2 cycle)
IO6* TIOR_SLREN Port I/O rise time, slew rate enabled — 25 — ns VDD = 3.0V
IO7* TIOR_SLRDIS Port I/O rise time, slew rate disabled — 5 — ns VDD = 3.0V
IO8* TIOF_SLREN Port I/O fall time, slew rate enabled — 25 — ns VDD = 3.0V
IO9* TIOF_SLRDIS Port I/O fall time, slew rate disabled — 5 — ns VDD = 3.0V
IO10* TINT INT pin high or low time to trigger an 25 — — ns
interrupt
IO11* TIOC Interrupt-on-Change minimum high or 25 — — ns
low time to trigger interrupt
*These parameters are characterized but not tested.

 2016-2018 Microchip Technology Inc. DS40001866B-page 529


PIC16(L)F15356/75/76/85/86
FIGURE 37-8: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING

VDD

MCLR
RST01
Internal
POR
RST04
PWRT
Time-out RST05

OSC
Start-up Time

Internal Reset(1)

Watchdog Timer
Reset(1)
RST03
RST02 RST02

I/O pins

Note 1:Asserted low.

FIGURE 37-9: BROWN-OUT RESET TIMING AND CHARACTERISTICS

VDD
VBOR + VHYST
VBOR

(Device in Brown-out Reset) (Device not in Brown-out Reset)

(RST08)(1)

Reset
(RST04)(1)
(due to BOR)

Note 1:64 ms delay only if PWRTE bit in the Configuration Word register is programmed to ‘1’; 2 ms
delay if PWRTE = 0.

 2016-2018 Microchip Technology Inc. DS40001866B-page 530


PIC16(L)F15356/75/76/85/86
TABLE 37-11: RESET, WDT, OSCILLATOR START-UP TIMER, POWER-UP TIMER, BROWN-OUT
RESET AND LOW-POWER BROWN-OUT RESET SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.

RST01* TMCLR MCLR Pulse Width Low to ensure Reset 2 — — s


RST02* TIOZ I/O high-impedance from Reset detection — — 2 s
RST03 TWDT Watchdog Timer Time-out Period — 16 — ms 16 ms Nominal Reset Time
RST04* TPWRT Power-up Timer Period — 65 — ms
RST05 TOST Oscillator Start-up Timer Period(1,2) — 1024 — TOSC
RST06 VBOR Brown-out Reset Voltage 2.55 2.70 2.85 V BORV = 0
2.30 2.45 2.60 V BORV = 1 (F devices)
1.80 1.90 2.10 V BORV = 1 (LF devices)
RST07 VBORHYS Brown-out Reset Hysteresis — 40 — mV
RST08 TBORDC Brown-out Reset Response Time — 3 — s
RST09 VLPBOR Low-Power Brown-out Reset Voltage 1.8 2.0 2.2 V LF Devices Only
*
These parameters are characterized but not tested.

Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: By design, the Oscillator Start-up Timer (OST) counts the first 1024 cycles, independent of frequency.
2: To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible.
0.1 F and 0.01 F values in parallel are recommended.

TABLE 37-12: ANALOG-TO-DIGITAL CONVERTER (ADC) ACCURACY SPECIFICATIONS(1,2):


Standard Operating Conditions (unless otherwise stated)
VDD = 3.0V, TA = 25°C
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
AD01 NR Resolution — — 10 bit
AD02 EIL Integral Error — ±0.1 ±1.0 LSb ADCREF+ = 3.0V, ADCREF-= 0V
AD03 EDL Differential Error — ±0.1 ±1.0 LSb ADCREF+ = 3.0V, ADCREF-= 0V
AD04 EOFF Offset Error — 0.5 2.0 LSb ADCREF+ = 3.0V, ADCREF-= 0V
AD05 EGN Gain Error — ±0.2 ±1.0 LSb ADCREF+ = 3.0V, ADCREF-= 0V
AD06 VADREF ADC Reference Voltage 1.8 — VDD V
(ADREF+)(3)
AD07 VAIN Full-Scale Range ADREF- — ADREF+ V
AD08 ZAIN Recommended Impedance of — 10 — k
Analog Voltage Source
AD09 RVREF ADC Voltage Reference Ladder — 50 — k Note 3
Impedance
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1:Total Absolute Error is the sum of the offset, gain and integral non-linearity (INL) errors.
2: The ADC conversion result never decreases with an increase in the input and has no missing codes.
3: This is the impedance seen by the VREF pads when the external reference pads are selected.

 2016-2018 Microchip Technology Inc. DS40001866B-page 531


PIC16(L)F15356/75/76/85/86
TABLE 37-13: ANALOG-TO-DIGITAL CONVERTER (ADC) CONVERSION TIMING SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)

Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
AD20 TAD ADC Clock Period 1 — 9 s The requirement is to set ADCCS
correctly to produce this period/
frequency.
AD21 1 2 6 s Using FRC as the ADC clock
source ADOSC = 1
AD22 TCNV Conversion Time — 11 — TAD Set of GO/DONE bit to Clear of GO/
DONE bit
AD23 TACQ Acquisition Time — 2 — s
AD24 THCD Sample and Hold Capacitor — — — s FOSC-based clock source
Disconnect Time FRC-based clock source
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.

FIGURE 37-10: ADC CONVERSION TIMING (ADC CLOCK FOSC-BASED)

BSF ADCON0, GO
1 TCY
AD24
AD22
Q4

ADC Data 9 8 7 6 3 2 1 0

ADRES OLD_DATA NEW_DATA

ADIF 1 TCY

GO DONE

AD23 Sampling Stopped


Sample

FIGURE 37-11: ADC CONVERSION TIMING (ADC CLOCK FROM ADCRC)

BSF ADCON0, GO
AD24 1 TCY
AD22
Q4
AD20
ADC_clk

ADC Data 9 8 7 6 3 2 1 0

ADRES OLD_DATA NEW_DATA

ADIF 1 TCY

GO DONE

AD23 Sampling Stopped


Sample

 2016-2018 Microchip Technology Inc. DS40001866B-page 532


PIC16(L)F15356/75/76/85/86
TABLE 37-14: COMPARATOR SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)
VDD = 3.0V, TA = 25°C

Param.
Sym. Characteristics Min. Typ. Max. Units Comments
No.
CM01 VIOFF Input Offset Voltage — — ±50 mV VICM = VDD/2
CM02 VICM Input Common Mode Range GND — VDD V
CM03 CMRR Common Mode Input Rejection Ratio — 50 — dB
CM04 VHYST Comparator Hysteresis 15 25 35 mV
CM05 TRESP(1) Response Time, Rising Edge — 300 600 ns
Response Time, Falling Edge — 220 500 ns
CMOS6 TMCV2VO(2) Mode Change to Valid Output — — 10 µs
* These parameters are characterized but not tested.
Note 1: Response time measured with one comparator input at VDD/2, while the other input transitions from VSS to VDD.
2: A mode change includes changing any of the control register values, including module enable.

TABLE 37-15: 5-BIT DAC SPECIFICATIONS


Standard Operating Conditions (unless otherwise stated)
VDD = 3.0V, TA = 25°C

Param.
Sym. Characteristics Min. Typ. Max. Units Comments
No.

DSB01 VLSB Step Size — (VDACREF+ -VDACREF-) /32 — V


DSB01 VACC Absolute Accuracy — —  0.5 LSb
DSB03* RUNIT Unit Resistor Value — 5000 — 
DSB04* TST Settling Time(1) — — 10 s
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Settling time measured while DACR<4:0> transitions from ‘00000’ to ‘01111’.

TABLE 37-16: FIXED VOLTAGE REFERENCE (FVR) SPECIFICATIONS


Standard Operating Conditions (unless otherwise stated)

Param.
Symbol Characteristic Min. Typ. Max. Units Conditions
No.
FVR01 VFVR1 1x Gain (1.024V) -4 — +4 % VDD  2.5V, -40°C to
85°C
FVR02 VFVR2 2x Gain (2.048V) -4 — +4 % VDD  2.5V, -40°C to
85°C
FVR03 VFVR4 4x Gain (4.096V) -6 — +6 % VDD  4.75V, -40°C
to 85°C
FVR04 TFVRST FVR Start-up Time — 25 — us
FVR05 FVRA1X/FVRC1X FVR output voltage for 1x setting stored in — 1024 — mV
the DIA
FVR06 FVRA2X/FVRC2X FVR output voltage for 2x setting stored in — 2048 — mV
the DIA
FVR07 FVRA4X/FVRC4X FVR output voltage for 4x setting stored in — 4096 — mV Note 1
the DIA
Note 1: Available only on PIC16F15354/55.

 2016-2018 Microchip Technology Inc. DS40001866B-page 533


PIC16(L)F15356/75/76/85/86
TABLE 37-17: ZERO CROSS DETECT (ZCD) SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)
VDD = 3.0V, TA = 25°C

Param.
Sym. Characteristics Min. Typ† Max. Units Comments
No.
ZC01 ZPCINV Voltage on Zero Cross Pin — 0.75 — V
ZC02 ZCDRV Maximum source or sink current — — 600 A
ZC04 ZCISW Response Time, Rising Edge — 1 — s
Response Time, Falling Edge — 1 — s
ZC05 ZCOUT Response Time, Rising Edge — 1 — s
Response Time, Falling Edge — 1 — s
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.

FIGURE 37-12: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS

T0CKI

40 41

42

T1CKI
45 46

47 49

TMR0 or
TMR1

 2016-2018 Microchip Technology Inc. DS40001866B-page 534


PIC16(L)F15356/75/76/85/86
TABLE 37-18: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
40* TT0H T0CKI High-Pulse Width No Prescaler 0.5 TCY + 20 — — ns
With Prescaler 10 — — ns
41* TT0L T0CKI Low-Pulse Width No Prescaler 0.5 TCY + 20 — — ns
With Prescaler 10 — — ns
42* TT0P T0CKI Period Greater of: 20 — — ns N = prescale value
or (TCY +40)*N (2, 4,...256)
45* TT1H T1CKI High Synchronous, No Prescaler 0.5 TCY + 20 — — ns
Time Synchronous, with Prescaler 15 — — ns
Asynchronous 30 — — ns
46* TT1L T1CKI Low Synchronous, No Prescaler 0.5 TCY + 20 — — ns
Time Synchronous, with Prescaler 15 — — ns
Asynchronous 30 — — ns
47* TT1P T1CKI Input Synchronous Greater of: 30 — — ns N = prescale value
Period or (TCY +40)*N (2, 4,...256)
Asynchronous 60 — — ns
48 F T1 Timer1 Oscillator Input Frequency Range 32.4 32.768 33.1 kHz
(oscillator enabled by setting bit T1OSCEN)
49* TCKEZTMR1 Delay from External Clock Edge to Timer 2 TOSC — 7 TOSC — Timers in Sync
Increment mode
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.

 2016-2018 Microchip Technology Inc. DS40001866B-page 535


PIC16(L)F15356/75/76/85/86
FIGURE 37-13: CAPTURE/COMPARE/PWM TIMINGS (CCP)
CCPx
(Capture mode)

CC01 CC02

CC03

Note: Refer to Figure 37-4 for load conditions.

TABLE 37-19: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP)


Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C  TA  +125°C
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
CC01* TccL CCPx Input Low Time No Prescaler 0.5TCY + 20 — — ns
With Prescaler 20 — — ns
CC02* TccH CCPx Input High Time No Prescaler 0.5TCY + 20 — — ns
With Prescaler 20 — — ns
CC03* TccP CCPx Input Period (3TCY +40)*N — — ns N = prescale value (1,4 or 16)
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.

 2016-2018 Microchip Technology Inc. DS40001866B-page 536


PIC16(L)F15356/75/76/85/86
FIGURE 37-14: CLC PROPAGATION TIMING
Rev. 10-000031A
6/16/2016

CLC LCx_in[n](1) CLC CLC


CLCxINn CLCx
Input time Module LCx_out(1) Output time

CLC CLC CLC


CLCxINn
Input time Module Output time
CLCx
LCx_in[n](1) LCx_out(1)

CLC01 CLC02 CLC03

Note 1: See Figure 31-1 to identify specific CLC signals.

TABLE 37-20: CONFIGURABLE LOGIC CELL (CLC) CHARACTERISTICS


Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +125°C
Param.
Sym. Characteristic Min. Typ† Max. Units Conditions
No.
CLC01* TCLCIN CLC input pin (CKCxIN) to CKC Module Input — 7 IO5 ns (Note 1)
select (LCx_IN) propagation time
CLC02* TCLC CLC Module input to output propagation delay — 24 — ns VDD = 1.8V
— 12 — ns VDD > 3.6V
CLC03* TCLCOUT CLC Module output time — IO7 — — Rise Time (Note 1)
— IO8 — — Fall Time (Note 1)
CLC04* FCLCMAX CLC Maximum switching frequency — 32 FOSC MHz
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1:See Table 37-10 for IO5, IO7 and IO8 rise and fall times.

 2016-2018 Microchip Technology Inc. DS40001866B-page 537


PIC16(L)F15356/75/76/85/86
FIGURE 37-15: EUSART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING

CK
US121 US121

DT

US120 US122

Note: Refer to Figure 37-4 for load conditions.

TABLE 37-21: EUSART SYNCHRONOUS TRANSMISSION CHARACTERISTICS


Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C

Param.
Symbol Characteristic Min. Max. Units Conditions
No.
US120 TCKH2DTV SYNC XMIT (Master and Slave) — 80 ns 3.0V  VDD  5.5V
Clock high to data-out valid — 100 ns 1.8V  VDD  5.5V
US121 TCKRF Clock out rise time and fall time — 45 ns 3.0V  VDD  5.5V
(Master mode) — 50 ns 1.8V  VDD  5.5V
US122 TDTRF Data-out rise time and fall time — 45 ns 3.0V  VDD  5.5V
— 50 ns 1.8V  VDD  5.5V

FIGURE 37-16: EUSART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING

CK
US125

DT
US126

Note: Refer to Figure 37-4 for load conditions.

TABLE 37-22: EUSART SYNCHRONOUS RECEIVE REQUIREMENTS


Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C

Param.
Symbol Characteristic Min. Max. Units Conditions
No.
US125 TDTV2CKL SYNC RCV (Master and Slave)
Data-setup before CK  (DT hold time) 10 — ns
US126 TCKL2DTL Data-hold after CK  (DT hold time) 15 — ns

 2016-2018 Microchip Technology Inc. DS40001866B-page 538


PIC16(L)F15356/75/76/85/86
FIGURE 37-17: SPI MASTER MODE TIMING (CKE = 0, SMP = 0)

SS
SP81
SCK
(CKP = 0)
SP71 SP72
SP78 SP79

SCK
(CKP = 1)

SP79 SP78
SP80

SDO MSb bit 6 - - - - - -1 LSb

SP75, SP76

SDI MSb In bit 6 - - - -1 LSb In

SP74
SP73

Note: Refer to Figure 37-4 for load conditions.

FIGURE 37-18: SPI MASTER MODE TIMING (CKE = 1, SMP = 1)

SS

SP81
SCK
(CKP = 0)
SP71 SP72
SP79
SP73
SCK
(CKP = 1)

SP80
SP78

SDO MSb bit 6 - - - - - -1 LSb

SP75, SP76

SDI MSb In bit 6 - - - -1 LSb In

SP74
SP73

Note: Refer to Figure 37-4 for load conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 539


PIC16(L)F15356/75/76/85/86
FIGURE 37-19: SPI SLAVE MODE TIMING (CKE = 0)

SS

SP70

SCK SP83
(CKP = 0)
SP71 SP72
SP78 SP79

SCK
(CKP = 1)

SP79 SP78
SP80

SDO MSb bit 6 - - - - - -1 LSb

SP75, SP76 SP77

SDI MSb In bit 6 - - - -1 LSb In

SP74

SP73

Note: Refer to Figure 37-4 for load conditions.

FIGURE 37-20: SPI SLAVE MODE TIMING (CKE = 1)

SP82
SS

SP70
SCK SP83
(CKP = 0)

SP71 SP72

SCK
(CKP = 1)

SP80

SDO MSb bit 6 - - - - - -1 LSb

SP77
SP75, SP76

SDI
MSb In bit 6 - - - -1 LSb In

SP74

SP73

Note: Refer to Figure 37-4 for load conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 540


PIC16(L)F15356/75/76/85/86
TABLE 37-23: SPI MODE REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)

Param.
Symbol Characteristic Min. Typ† Max. Units Conditions
No.

SP70* TSSL2SCH, SS to SCK or SCK input 2.25*TCY — — ns


TSSL2SCL
SP71* TSCH SCK input high time (Slave mode) TCY + 20 — — ns
SP72* TSCL SCK input low time (Slave mode) TCY + 20 — — ns
SP73* TDIV2SCH, Setup time of SDI data input to SCK 100 — — ns
TDIV2SCL edge
SP74* TSCH2DIL, Hold time of SDI data input to SCK edge 100 — — ns
TSCL2DIL
SP75* TDOR SDO data output rise time — 10 25 ns 3.0V  VDD  5.5V
— 25 50 ns 1.8V  VDD  5.5V
SP76* TDOF SDO data output fall time — 10 25 ns
SP77* TSSH2DOZ SS to SDO output high impedance 10 — 50 ns
SP78* TSCR SCK output rise time — 10 25 ns 3.0V  VDD  5.5V
(Master mode) — 25 50 ns 1.8V  VDD  5.5V
SP79* TSCF SCK output fall time (Master mode) — 10 25 ns
SP80* TSCH2DOV, SDO data output valid after SCK edge — — 50 ns 3.0V  VDD  5.5V
TSCL2DOV — — 145 ns 1.8V  VDD  5.5V
SP81* TDOV2SCH, SDO data output setup to SCK edge 1 Tcy — — ns
TDOV2SCL
SP82* TSSL2DOV SDO data output valid after SS edge — — 50 ns
SP83* TSCH2SSH, SS after SCK edge 1.5 TCY + 40 — — ns
TSCL2SSH
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.

 2016-2018 Microchip Technology Inc. DS40001866B-page 541


PIC16(L)F15356/75/76/85/86
FIGURE 37-21: I2C BUS START/STOP BITS TIMING

SCL
SP91 SP93
SP90 SP92

SDA

Start Stop
Condition Condition

Note: Refer to Figure 37-4 for load conditions.

TABLE 37-24: I2C BUS START/STOP BITS REQUIREMENTS


Standard Operating Conditions (unless otherwise stated)

Param.
Symbol Characteristic Min. Typ Max. Units Conditions
No.

SP90* TSU:STA Start condition 100 kHz mode 4700 — — ns Only relevant for Repeated Start
Setup time 400 kHz mode 600 — — condition

SP91* THD:STA Start condition 100 kHz mode 4000 — — ns After this period, the first clock
Hold time 400 kHz mode 600 — — pulse is generated

SP92* TSU:STO Stop condition 100 kHz mode 4700 — — ns


Setup time 400 kHz mode 600 — —
SP93 THD:STO Stop condition 100 kHz mode 4000 — — ns
Hold time 400 kHz mode 600 — —
* These parameters are characterized but not tested.

FIGURE 37-22: I2C BUS DATA TIMING

SP103 SP100 SP102


SP101

SCL
SP90
SP106
SP107
SP91 SP92
SDA
In
SP110
SP109
SP109
SDA
Out

Note: Refer to Figure 37-4 for load conditions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 542


PIC16(L)F15356/75/76/85/86
TABLE 37-25: I2C BUS DATA REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)

Param.
Symbol Characteristic Min. Max. Units Conditions
No.

SP100* THIGH Clock high time 100 kHz mode 4.0 — s Device must operate at a
minimum of 1.5 MHz
400 kHz mode 0.6 — s Device must operate at a
minimum of 10 MHz
SSP module 1.5TCY —
SP101* TLOW Clock low time 100 kHz mode 4.7 — s Device must operate at a
minimum of 1.5 MHz
400 kHz mode 1.3 — s Device must operate at a
minimum of 10 MHz
SSP module 1.5 TCY —
SP102* TR SDA and SCL rise 100 kHz mode — 1000 ns
time 400 kHz mode 20 + 0.1 CB 300 ns CB is specified to be from
10-400 pF
SP103* TF SDA and SCL fall time 100 kHz mode — 250 ns
400 kHz mode 20 + 0.1 CB 250 ns CB is specified to be from
10-400 pF
SP106* THD:DAT Data input hold time 100 kHz mode 0 — ns
400 kHz mode 0 0.9 s
SP107* TSU:DAT Data input setup time 100 kHz mode 250 — ns (Note 2)
400 kHz mode 100 — ns
SP109* TAA Output valid from 100 kHz mode — 3500 ns (Note 1)
clock 400 kHz mode — — ns
SP110* TBUF Bus free time 100 kHz mode 4.7 — s Time the bus must be free
400 kHz mode 1.3 — s before a new transmission
can start
SP111 CB Bus capacitive loading — 400 pF
* These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns)
of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
2: A Fast mode (400 kHz) I2C bus device can be used in a Standard mode (100 kHz) I2C bus system, but the requirement
TSU:DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the low period of
the SCL signal. If such a device does stretch the low period of the SCL signal, it must output the next data bit to the SDA
line TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCL
line is released.

TABLE 37-26: TEMPERATURE INDICATOR REQUIREMENTS


Standard Operating Conditions (unless otherwise stated)

Param No. Symbol Characteristic Min. Typ† Max. Units Conditions


TS01 TACQMIN Minimum ADC Acquisition Time Delay — 25 — s
TS02 MV Voltage Sensitivity High Range — -3.684 — mV/°C TSRNG = 1
Low Range — -2.456 — mV/°C TSRNG = 0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.

 2016-2018 Microchip Technology Inc. DS40001866B-page 543


PIC16(L)F15356/75/76/85/86
38.0 DC AND AC
CHARACTERISTICS GRAPHS
AND CHARTS
The graphs and tables provided in this section are for design guidance and are not tested.
In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD
range). This is for information only and devices are ensured to operate properly only within the specified range.
Unless otherwise noted, all graphs apply to both the L and LF devices.
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore, outside the warranted range.
“Typical” represents the mean of the distribution at 25C. “Maximum”, “Max.”, “Minimum” or “Min.”
represents (mean + 3) or (mean - 3) respectively, where  is a standard deviation, over each
temperature range.

 2016-2018 Microchip Technology Inc. DS40001866B-page 544


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

1.0 1.0

0.5 0.5

DNL (LSb)
DNL (LSb)

0.0 0.0

-0.5 -0.5

-1.0 -1.0
0 128 256 384 512 640 768 896 1024 0 128 256 384 512 640 768 896 1024

Output Code Output Code

FIGURE 38-1: ADC 10-bit Mode, Single- FIGURE 38-2: ADC 10-bit Mode, Single-
Ended DNL, VDD= 3.0V, VREF = 3.0V, TAD = 1 Ended DNL, VDD= 3.0V, VREF = 3.0V, TAD = 4
uS, 25°C. uS, 25°C.

1.0 1.0

0.5 0.5
DNL (LSb)

INL (LSb)

0.0 0.0

-0.5 -0.5

-1.0 -1.0
0 128 256 384 512 640 768 896 1024 0 128 256 384 512 640 768 896 1024

Output Code Output Code

FIGURE 38-3: ADC 10-bit Mode, Single- FIGURE 38-4: ADC 10-bit Mode, Single-
Ended DNL, VDD= 3.0V, VREF = 3.0V, TAD = 8 Ended INL, VDD= 3.0V, VREF = 3.0V, TAD = 1 uS,
uS, 25°C. 25°C.

2.0 2.0
1.0 1.0
1.5 1.5

1.0 1.0

0.5
0.5 0.5
DNL (LSb)

0.5
DNL (LSb)

0.0 0.0
INL (LSb)

INL (LSb)

-0.5 -0.5
0.0 0.0
-1.0 -1.0

-1.5 -1.5

-2.0 -2.0
-0.5 -0.5
0 512 1024 1536 2048 2560 3072 3584 4096 0 512 1024 1536 2048 2560 3072 3584 4096
Output Code Output Code

-1.0 -1.0
0 128 256 384 512 640 768 896 1024 0 128 256 384 512 640 768 896 1024

Output Code Output Code

FIGURE 38-5: ADC 10-bit Mode, Single- FIGURE 38-6: ADC 10-bit Mode, Single-
Ended INL, VDD= 3.0V, VREF = 3.0V, TAD = 4 uS, Ended INL, VDD= 3.0V, VREF = 3.0V, TAD = 8 uS,
25°C. 25°C.

DS40001866A-page 545  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

1 1

0.5 0.5
DNL (LSB)

INL (LSB)
0 0

-0.5 -0.5
Max 25°C Max 25°C
Min 25°C Min 25°C
Max -40°C Max -40°C
Min -40°C Min -40°C
Max 85°C Max 85°C
Min 85°C Min 85°C
-1 -1
0.5 0.8 1 2 4 8 0.5 0.8 1 2 4 8
TADs TADs

FIGURE 38-7: ADC 10-bit Mode, Single- FIGURE 38-8: ADC 10-bit Mode, Single-
Ended DNL, VDD= 3.0V, VREF = 3.0V Ended INL, VDD= 3.0V, VREF = 3.0V

1 2

1.5

0.5 1

0.5
DNL(LSB)

INL(LSB)

0 0

-0.5

-0.5 -1
Max 85°C Max 85°C
Max 25°C Max 25°C
Max -40°C Max -40°C
Min 85°C -1.5 Min 85°C
Min 25°C Min 25°C
Min -40°C Min -40°C
-1 -2
1.8 2.3 2.5 3 1.8 2.3 2.5 3
VREF VREF

FIGURE 38-9: ADC 10-bit Mode, Single- FIGURE 38-10: ADC 10-bit Mode, Single-
Ended DNL, VDD= 3.0V, TAD = 1 uS Ended INL, VDD= 3.0V, TAD = 1 uS

6 3
5 2.5
4 2
3 1.5
2 1
1 0.5
(LSB)

(LSB)

0 0
-1 -0.5
-2 -1
-3 -1.5
Max 85°C Max 85°C
-4 Max 25°C Max 25°C
Max -40°C
-2 Max -40°C
Min 85°C Min 85°C
-5 Min 25°C -2.5 Min 25°C
Min -40°C Min -40°C
-6 -3
1.8 2.3 2.5 3 1.8 2.3 2.5 3
VREF VREF

FIGURE 38-11: ADC 10-bit Mode, Single- FIGURE 38-12: ADC 10-bit Mode, Single-
Ended Gain Error, VDD= 3.0V, TAD = 1 uS Ended Offset Error, VDD= 3.0V, TAD = 1 uS

 2016-2018 Microchip Technology Inc. DS40001866A-page 546


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

1 1

0.5 0.5
DNL(LSB)

INL(LSB)
0 0

-0.5 -0.5
Max 85°C Max 85°C
Max 25°C Max 25°C
Max -40°C Max -40°C
Min 85°C Min 85°C
Min 25°C Min 25°C
Min -40°C Min -40°C
-1 -1
1.8 2.3 2.5 3 1.8 2.3 2.5 3
VREF VREF

FIGURE 38-13: ADC 10-bit Mode, Single- FIGURE 38-14: ADC 10-bit Mode, Single-
Ended DNL, VDD= 3.0V, TAD = 4 uS. Ended INL, VDD= 3.0V, TAD = 4 uS.

6 1

3 0.5

1
(LSB)
(LSB)

0 0

-1

-2

-3 -0.5
Max 85°C Max 85°C
Max 25°C Max 25°C
-4
Max -40°C Max -40°C
Min 85°C Min 85°C
-5 Min 25°C Min 25°C
Min -40°C Min -40°C
-6 -1
1.8 2.3 2.5 3 1.8 2.3 2.5 3
VREF VREF

FIGURE 38-15: ADC 10-bit Mode, Single- FIGURE 38-16: ADC 10-bit Mode, Single-
Ended Gain Error, VDD= 3.0V, TAD = 4 uS Ended Offset Error, VDD= 3.0V, TAD = 4 uS

2 2

1.5 1.5

1 1

0.5 0.5
(LSB)
(LSB)

0 0

-0.5 -0.5

-1 -1

Max Max
-1.5 -1.5 Typical
Typical
Min Min
-2 -2
0.5 0.8 1 2 4 8 0.5 0.8 1 2 4 8
TADs TADs

FIGURE 38-17: ADC 10-bit Mode, Single- FIGURE 38-18: ADC 10-bit Mode, Single-
Ended Gain Error, VDD= 3.0V, VREF = 3.0V, - Ended Offset Error, VDD= 3.0V, VREF = 3.0V, -
40°C to 85°C. 40°C to 85°C

DS40001866A-page 547  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

5.0 4.0
Typical 25°C
4.5
+3ı (-40°C to +125°C) 3.5
4.0 -3ı (-40°C to +125°C)
3.0
3.5

3.0 2.5
Time (us)

Time (us)
2.5 2.0

2.0
1.5
1.5
1.0
1.0 Typical 25°C
0.5 +3ı (-40°C to +125°C)
0.5
-3ı (-40°C to +125°C)
0.0 0.0
1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6
VDD (V)
VDD (V)

FIGURE 38-19: ADC RC Oscillator Period, FIGURE 38-20: ADC RC Oscillator Period,
PIC16LF15356/75/76/85/86 devices only. PIC16F15356/75/76/85/86 devices only.

70 5.0
Typical 25°C Typical 25°C
4.5
+3ı (-40°C to +125°C) +3 Sigma 125°C
60
4.0

3.5
50
Time (us)

3.0
Time (us)

40 2.5

2.0
30
1.5

1.0
20
0.5

10 0.0
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7
VDD (V) VDD (V)

FIGURE 38-21: Band Gap Ready FIGURE 38-22: Brown-out Reset Response
Time, PIC16LF15356/75/76/85/86 devices only.

7
3.00
Typical 25°C +3 Sigma
2.95
6 +3 Sigma 125°C -3 Sigma
2.90
Typical
2.85
5
2.80
Time (us)

2.75
Voltage (V)

4
2.70

3 2.65
2.60
2 2.55
2.50
1 2.45
2.40
0 -60 -40 -20 0 20 40 60 80 100 120 140
2.6 2.8 3 3.2 3.4 3.6 3.8 4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6 Temperature (°C)
VDD (V)

FIGURE 38-23: Brown-out Reset Response FIGURE 38-24: Brown-out Reset Voltage,
Time, PIC16F15356/75/76/85/86 devices only. Trip Point (BORV = 00)

 2016-2018 Microchip Technology Inc. DS40001866A-page 548


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

70.0 2.00
Typical

60.0 +3 Sigma
-3 Sigma
1.95
50.0

40.0
Voltage (mV)

Voltage (V)
1.90
30.0

20.0
1.85 +3 Sigma
-3 Sigma
10.0
Typical

0.0 1.80
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140

Temperature (°C) Temperature (°C)

FIGURE 38-25: Brown-out Reset FIGURE 38-26: Brown-out Reset Voltage,


Hysteresis, Low-Trip Point (BORV = 00) Trip Point (BORV = 01)

40.0 2.60
+3 Sigma
35.0 2.50
Typical

2.40 -3 Sigma
30.0

2.30
25.0
Voltage (V)
Voltage (mV)

2.20
20.0
2.10
15.0
2.00
10.0
Typical
1.90
5.0 +3 Sigma
-3 Sigma 1.80
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 1.70
-60 -40 -20 0 20 40 60 80 100 120 140
Temperature (°C)
Temperature (°C)

FIGURE 38-27: Brown-out Reset FIGURE 38-28: LPBOR Reset Voltage


Hysteresis, Trip Point (BORV = 01)

50 300
Typical Typical 25°C
45
+3 Sigma +3 Sigma 125°C
250
40 -3 Sigma
35
200
30
Time (ns)
Voltage (mV)

25
150
20

15
100
10

5 50

0
-60 -40 -20 0 20 40 60 80 100 120 140
0
1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7
Temperature (°C) VDD (V)

FIGURE 38-29: LPBOR Reset Hysteresis FIGURE 38-30: Comparator Response Time
Falling Edge, PIC16LF15356/75/76/85/86
devices only.

DS40001866A-page 549  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

250 700
Typical 25°C
Typical 25°C
600 +3 Sigma 125°C
+3 Sigma 125°C
200
500

150

Time (ns)
Time (ns)

400

300
100

200

50
100

0
0 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7
2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
VDD (V)
VDD (V)

FIGURE 38-31: Comparator Response Time FIGURE 38-32: Comparator Response Time
Falling Edge, PIC16F15356/75/76/85/86 devices Rising Edge, PIC16LF15356/75/76/85/86
only. devices only.

45
900
Typical 25°C 43
800 -40°C
+3 Sigma 125°C
41
700
39
25°C
Hysteresis (mV)
600
37 85°C
Time (ns)

500
35 125°
400
33
300
31
200
29
100
27
0
25
2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
VDD (V)
Common Mode Voltage (V)

FIGURE 38-33: Comparator Response Time FIGURE 38-34: Comparator Hysteresis,


Rising Edge, PIC16F15356/75/76/85/86 devices Normal Power Mode (CxSP = 1), VDD = 3.0V,
only. Typical Measured Values

30 30

25 25

20 20

15 15
Offset Voltage (mV)

Offset Voltage (mV)

10 10
MAX MAX
5 5

0 0

-5 MIN -5
MIN
-10 -10

-15 -15

-20 -20
0.0 0.5 1.0 1.5 2.0 2.5 3.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0

Common Mode Voltage (V) Common Mode Voltage (V)

FIGURE 38-35: Comparator Offset, Normal FIGURE 38-36: Comparator Offset, Normal
Power Mode (CxSP = 1), VDD = 3.0V, Typical Power Mode (CxSP = 1), VDD = 3.0V, Typical
Measured Values at 25°C. Measured Values from -40°C to 125°C.

 2016-2018 Microchip Technology Inc. DS40001866A-page 550


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

50 30

25

45 20

15

Hysteresis (mV)
Hysteresis (mV)

40
MAX
25°C 10
125°
35 5

0
85°
30 -5

-40°C -10
25 MIN
-15

20 -20
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

Common Mode Voltage (V) Common Mode Voltage (V)

FIGURE 38-37: Comparator Hysteresis, FIGURE 38-38: Comparator Offset, Normal


Normal Power Mode (CxSP = 1), VDD = 5.5V, Power Mode (CxSP = 1), VDD = 5.0V, Typical
Typical Measured Values, PIC16F15356/75/76/ Measured Values at 25°C, PIC16F15356/75/76/
85/86 devices only. 85/86 devices only.

140
40
Max: Typical + 3ı (-40°C to +125°C)
120 Typical; statistical mean @ 25°C
Min: Typical - 3ı (-40°C to +125°C)
30

100
Offset Voltage (mV)

20 125°C
Time (nS)

80
MAX
10 25°C
60

0
40

-40°C
-10
20
MIN

-20 0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 1.7 2.0 2.3 2.6 2.9 3.2 3.5

Common Mode Voltage (V) VDD (V)

FIGURE 38-39: Comparator Offset, Normal FIGURE 38-40: Comparator Response Time
Power Mode (CxSP = 1), VDD = 5.5V, Typical Over Voltage, Normal Power Mode (CxSP = 1),
Measured Values from -40°C to 125°C, Typical Measured Values, PIC16LF15356/75/76/
PIC16F15356/75/76/85/86 devices only. 85/86 devices only.

90 1,400
Max: Typical + 3ı (-40°C to +125°C) Max: Typical + 3ı (-40°C to +125°C)
80 Typical; statistical mean @ 25°C Typical; statistical mean @ 25°C
Min: Typical - 3ı (-40°C to +125°C) 1,200 Min: Typical - 3ı (-40°C to +125°C)
70

125°C 1,000
60
Time (nS)

Time (nS)

50 800
25°C 125°C
40
600

30 25°C
-40°C 400
20

200
10
-40°C
0 0
2.2 2.5 2.8 3.1 3.4 3.7 4.0 4.3 4.6 4.9 5.2 5.5 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

VDD (V) VDD (V)

FIGURE 38-41: Comparator Response Time FIGURE 38-42: Comparator Output Filter
Over Voltage, Normal Power Mode (CxSP = 1), Delay Time Over Temperature, Normal Power
Typical Measured Values, PIC16F15356/75/76/ Mode (CxSP = 1), Typical Measured Values,
85/86 devices only. PIC16LF15356/75/76/85/86 devices only.

DS40001866A-page 551  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

0.025
800

Max: Typical + 3ı (-40°C to +125°C)


0.02
700 Typical; statistical mean @ 25°C
Min: Typical - 3ı (-40°C to +125°C)
0.015
600

0.01
500
Time (nS)

DNL (LSb)
125°C 0.005
-40°C
400
25°C
0
300 85°C
25°C -0.005 125°C
200
-0.01
100
-40°C -0.015
0
2.2 2.5 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 5.5 -0.02
0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240
VDD (V) Output Code

FIGURE 38-43: Comparator Output Filter FIGURE 38-44: Typical DAC DNL Error,
Delay Time Over Temperature, Normal Power VDD = 3.0V, VREF = External 3V
Mode (CxSP = 1), Typical Measured Values,
PIC16F15356/75/76/85/86 devices only

0.00 0.45
0.4
Vref = Int. Vdd
0.4
-0.05 Vref = Ext. 1.8V
0.35 Vref = Ext. 2.0V

DNL (LSb)
-0.10 Vref = Ext. 3.0V
0.3
0.3

-0.15
DNL (LSb) 0.25 Vref = Int. Vdd
Vref = Ext. 1.8V
AbsoluteAbsolute

0.2
INL (LSb)

-0.20 Vref = Ext. 2.0V


-40°C 0.15
0.2 Vref = Ext. 3.0V
25°C
-0.25 0.1
85°C
0.05
-0.30 125°C
0
0.1 -50 0 50 100 150
-0.35
Temperature (°C)
-0.40

-0.45 0.0
0 14 28 42 56 70 84 98 112126140 154168 182196210 224238 252 -60 -40 -20 0 20 40 60 80 100 120 140
Output Code Temperature (°C)

FIGURE 38-45: Typical DAC INL Error, FIGURE 38-46: Absolute Value of DAC DNL
VDD = 3.0V, VREF = External 3V Error, VDD = 3.0V, VREF= VDD

0.90
-2.1 Vref = Int. Vdd
70
Vref = Ext. 1.8V Typical 25°C
-2.3 Vref = Ext. 2.0V
0.88 +3ı (-40°C to +125°C)
60
INL (LSb)INL (LSb)

Vref = Ext. 3.0V


-2.5

-40 50
-2.7
0.86
AbsoluteAbsolute

25
-2.9 40
Time (us)

85
0.84 125
-3.1
30
-3.3
0.82
20
-3.5
0.0 1.0 2.0 3.0 4.0 5.0
Temperature (°C) 10 Note:
0.80 The FVR Stabiliztion Period applies when coming out of
RESET or exiting sleep mode.

0
0.78 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8
-60.0 -40.0 -20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 VDD (MV)
Temperature (°C)

FIGURE 38-47: Absolute Value of DAC INL FIGURE 38-48: FVR Stabilization Period,
Error, VDD = 3.0V, VREF= VDD PIC16LF15356/75/76/85/86 devices only

 2016-2018 Microchip Technology Inc. DS40001866A-page 552


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

1.1% 1.2%
Typical -40°C Typical -40°C
Typical 25°C Typical 25°C
1.0% Typical 85°C Typical 85°C
Typical 125°C Typical 125°C
0.9% 1.0%

0.8%
0.8%
0.7%
Error (%)

Error (%)
0.6%
0.6%
0.5%

0.4%
0.4%
0.3%

0.2%
0.2%
0.1%

0.0%
2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 0.0%
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
VDD (V)
VDD (V)

FIGURE 38-49: Typical FVR Voltage 1X, FIGURE 38-50: FVR Voltage Error 1X,
PIC16F15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

1.0% 1.0%

0.8%
0.8%

0.6%
0.6%
Error (%)

0.4%
Error (%)

0.4%
0.2%

0.2%
0.0%
Typical -40°C
0.0% Typical -40°C
Typical 25°C
-0.2% Typical 25°C
Typical 85°C Typical 85°C
Typical 125°C Typical 125°C
-0.2%
-0.4%
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7
VDD (V) VDD (V)

FIGURE 38-51: FVR Voltage Error 2X, FIGURE 38-52: FVR Voltage Error 2X,
PIC16LF15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

1.0%
Typical -40°C 3.0%
Typical 25°C
0.8% Typical 85°C
Typical 125°C 2.0%

0.6% 1.0%

0.0%
Error (%)

0.4%
Error (%)

-1.0%
0.2%
-2.0%

0.0%
-3.0%
Typical 25°C
-0.2% -4.0% +3ı (-40°C to +125°C)
-3ı (-40°C to +125°C)
-0.4% -5.0%
4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8
VDD (V) VDD (V)

FIGURE 38-53: FVR Voltage Error 4X, FIGURE 38-54: HFINTOSC Typical
PIC16F15356/75/76/85/86 devices only Frequency Error, PIC16LF15356/75/76/85/86
devices only

DS40001866A-page 553  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

500 500
Max: 85°C + 3ı Max: 85°C + 3ı
450 Typical: 25°C 450 Typical: 25°C
Max
400 400
Typical
350 350
Max
300 300

IDD (µA)
IDD (µA)

Typical 250
250

200 200

150 150

100 100

50 50

0 0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V)
VDD (V)

FIGURE 38-55: IDD, XT Oscillator 4 MHz, FIGURE 38-56: IDD, XT Oscillator 4 MHz,
PIC16F15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

4.0 4.0
Max: 85°C + 3ı Max: 85°C + 3ı
Typical: 25°C Typical: 25°C
3.5 3.5

3.0 3.0
Max
2.5 2.5
Max
IDD (MA)
IDD (MA)

2.0 2.0
Typical
1.5 Typical 1.5

1.0 1.0

0.5 0.5

0.0 0.0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-57: IDD, HS Oscillator 32 MHz, FIGURE 38-58: IDD, HS Oscillator 32 MHz,
PIC16LF15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

4.0 4.0
Max: 85°C + 3ı Max: 85°C + 3ı
Typical: 25°C Typical: 25°C
3.5 3.5

3.0 3.0 Max

2.5 Max 2.5


IDD (MA)

IDD (MA)

Typical
2.0 2.0

Typical
1.5 1.5

1.0 1.0

0.5 0.5

0.0 0.0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V) VDD (V)

FIGURE 38-59: IDD, HFINTOSC Mode, FIGURE 38-60: IDD, HFINTOSC Mode,
FOSC = 32 MHz, PIC16LF15356/75/76/85/86 FOSC = 32 MHz, PIC16F15356/75/76/85/86
devices only devices only

 2016-2018 Microchip Technology Inc. DS40001866A-page 554


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

2.0 2.0
Max: 85°C + 3ı Max: 85°C + 3ı
1.8 Typical: 25°C 1.8 Typical: 25°C Max

1.6 1.6

1.4 1.4
Max
1.2 1.2 Typical-

IDD (MA)
IDD (MA)

1.0 1.0
Typical
0.8 0.8

0.6 0.6

0.4 0.4

0.2 0.2

0.0 0.0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V) VDD (V)

FIGURE 38-61: IDD, HFINTOSC Mode, FIGURE 38-62: IDD, HFINTOSC Mode,
FOSC = 16 MHz, PIC16LF15356/75/76/85/86 FOSC = 16 MHz, PIC16F15356/75/76/85/86
devices only devices only

1,200 1,200
Max: 85°C + 3ı Max: 85°C + 3ı
Typical: 25°C Typical: 25°C
1,000 Max
1,000

Max
800 800
Typical
IDD (µA)
IDD (µA)

600 600
Typical

400 400

200 200

0 0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V) VDD (V)

FIGURE 38-63: IDD, HFINTOSC Idle Mode, FIGURE 38-64: IDD, HFINTOSC Idle Mode,
FOSC = 16 MHz, PIC16LF15356/75/76/85/86 FOSC = 16 MHz, PIC16F15356/75/76/85/86
devices only devices only

1,200 1,200
Max: 85°C + 3ı Max: 85°C + 3ı
Typical: 25°C Typical: 25°C Max
1,000 1,000

Max
800 800 Typical
IDD (µA)

IDD (µA)

Typical
600 600

400 400

200 200

0 0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V) VDD (V)

FIGURE 38-65: IDD, HFINTOSC Doze FIGURE 38-66: IDD, HFINTOSC Doze
Mode, FOSC = 16 MHz, PIC16LF15356/75/76/85/ Mode, FOSC = 16 MHz, PIC16F15356/75/76/85/
86 devices only 86 devices only

DS40001866A-page 555  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.
Title Schmitt Trigger Low Values

4 2.5
Typical 25°C Typical 25°C
3.5 +3ı (-40°C to +125°C) +3ı (-40°C to +125°C)
-3ı (-40°C to +125°C) 2 -3ı (-40°C to +125°C)
3

2.5

Voltage (V)
1.5
Voltage (V)

1
1.5

1
0.5

0.5

0
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V)
VDD (V)

FIGURE 38-67: Schmitt Trigger High Values FIGURE 38-68: Schmitt Trigger Low Values

1.8 50
Typical 25°C Typical 25°C
45
1.6 +3ı (-40°C to +125°C) +3 Sigma (-40°C to
-3ı (-40°C to +125°C)
40 125°C)
1.4
Voltage (V)

35
1.2
30
Time (ns)

1 25
0.8 20

0.6 15

10
0.4
5
0.2
0
0 1.5 2.5 3.5 4.5 5.5
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V)
VDD (V)

FIGURE 38-69: Input Level TTL Trip FIGURE 38-70: Rise Time, Slew Rate
Thresholds Control Enabled

60 30
Typical 25°C Typical 25°C

+3 Sigma (-40°C to +3 Sigma (-40°C to


50 25 125°C)
125°C)

40 20
Time (ns)

Time (ns)

30 15

20 10

10 5

0 0
1.5 2.5 3.5 4.5 5.5 1.5 2.5 3.5 4.5 5.5
VDD (V) VDD (V)

FIGURE 38-71: Fall Time, Slew Rate Control FIGURE 38-72: Rise Time, Slew Rate
Enabled Control Disabled

 2016-2018 Microchip Technology Inc. DS40001866A-page 556


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

600
20 Typical 25°C
Max: 85°C + 3ı Max.
18 +3 Sigma (-40°C to 500 Typical: 25°C
16 125°C)

14 400

IPD (nA)
12
Time (ns)

10 300

8
200
6

4 Typical
100
2

0
1.5 2.5 3.5 4.5 5.5 0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8
VDD (V)

VDD (V)

FIGURE 38-73: Rise Time, Slew Rate FIGURE 38-74: IPD Base, Low-Power Sleep
Control Disabled Mode, PIC16LF15356/75/76/85/86 devices only

1.0 1.4
Max: 85°C + 3ı Max: 85°C + 3ı
0.9 Typical: 25°C Typical: 25°C
Max. 1.2 Max.
0.8

0.7
1.0
0.6
IPD (µA)
IPD (µA)

Typical
0.5 Typical 0.8

0.4
0.6
0.3

0.2
0.4
0.1

0.0 0.2
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-75: IPD, Watchdog Timer FIGURE 38-76: IPD, Watchdog Timer
(WDT), PIC16LF15356/75/76/85/86 devices only (WDT), PIC16F15356/75/76/85/86 devices only

60
60
Max: 85°C + 3ı
Max: 85°C + 3ı
55 Typical: 25°C
Typical: 25°C
55
50
50
45

45 40
IPD (µA)
IPD (µA)

35 Max.
40

30
35 Max.
25 Typical

30
20

25 Typical 15

20 10
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-77: IPD, Fixed Voltage FIGURE 38-78: IPD, Fixed Voltage
Reference (FVR), PIC16LF15356/75/76/85/86 Reference (FVR), PIC16F15356/75/76/85/86
devices only devices only

DS40001866A-page 557  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

14 16
Max: 85°C + 3ı Max: 85°C + 3ı
Typical: 25°C Typical: 25°C
13 14

12 12
IPD (µA)

Typical

IPD (µA)
11 10

10 8
Typical

9 6

8 4
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-79: IPD, Brown-out Reset FIGURE 38-80: IPD, Brown-out Reset
(BOR), BORV = 1, PIC16LF15356/75/76/85/86 (BOR), BORV = 1, PIC16F15356/75/76/85/86
devices only devices only

1.2 1.4

Max: 85°C + 3ı Max.


Max: 85°C + 3ı
Typical: 25°C Typical: 25°C
1 1.2
Max.

1.0
0.8
IPD (µA)

0.8
IPD (nA)

0.6
0.6
Typical
0.4
0.4

0.2
0.2
Typical

0 0.0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-81: IPD, Low-Power Brown-out FIGURE 38-82: IPD, Low-Power Brown-out
Reset (LPBOR = 0), PIC16LF15356/75/76/85/86 Reset (LPBOR = 0), PIC16F15356/75/76/85/86
devices only devices only

40 40

Max: 85°C + 3ı Max: 85°C + 3ı


39 Typical: 25°C
38 Typical: 25°C
38
36 Max.
37 Max.
34
36
IPD (µA)

IPD (µA)

32 35
Typical
34
30 Typical
33
28
32
26
31

24 30
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-83: IPD, Comparator, FIGURE 38-84: IPD, Comparator,


PIC16LF15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

 2016-2018 Microchip Technology Inc. DS40001866A-page 558


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

30 1 Max.
Max: 85°C + 3ı 0.9
Typical: 25°C Max. Max: 85°C + 3ı
25 Typical: 25°C
0.8

0.7
20
0.6
IPD (µA)

IPD (µA)
Typical
15 0.5 Typical

0.4
10
0.3

0.2
5
0.1

0 0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-85: Ipd Base, 01, PIC16F15356/ FIGURE 38-86: Ipd Base, 11, PIC16F15356/
75/76/85/86 devices only 75/76/85/86 devices only

36,000
36,000 Typical 25°C
Typical 25°C
35,000 +3 Sigma (-40°C to 125°C)
35,000 +3 Sigma (-40°C to 125°C)
-3 Sigma (-40°C to 125°C)
-3 Sigma (-40°C to 125°C)
34,000
34,000

33,000
33,000
Frequency (Hz)
Frequency (Hz)

32,000
32,000

31,000
31,000

30,000
30,000

29,000
29,000

28,000
28,000 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6
1.7 2.0 2.3 2.6 2.9 3.2 3.5
VDD (V)
VDD (V)

FIGURE 38-87: LFINTOSC Frequency, FIGURE 38-88: LFINTOSC Frequency,


PIC16LF15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

4.00% 1.6
Max: Typical + 3ı (-40°C to +125°C)
3.00% Typical; statistical mean @ 25°C
Min: Typical - 3ı (-40°C to +125°C) 1.55

+3 Sigma
2.00% 1.5

1.00% 1.45
Voltage (V)
Error (%)

Typical
0.00% 1.4

-1.00% 1.35

-2.00% 1.3 -3 Sigma


Max
-3.00% Min 1.25
Average
-4.00% 1.2
-32 -24 -16 -8 0 8 16 24 32 -60 -40 -20 0 20 40 60 80 100 120 140
Min Center Max
Temperature (°C)
OSCTUNE Setting

FIGURE 38-89: OCSTUNE Center FIGURE 38-90: Power-on Reset Release


Frequency, PIC16(L)F15356/75/76/85/86 Voltage
devices only

DS40001866A-page 559  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

1.64
1.8
Max: Typical + 3ı
Typical: 25°C 74.0
1.63
Min: Typical - 3ı
1.75
72.0
1.62
(V) (V)

1.7 +3 Sigma
70.0
Voltage

1.61

Time (ms)
Voltage

Typical 68.0
1.6
1.65

66.0
1.59
1.6
64.0
1.58 -3 Sigma
-40 -20 0 20 40 60 80 100 120
1.55 62.0 Typical 25°C
Temperature (°C) + 3ı (-40°C to +125°C)
- 3ı (-40°C to +125°C)
60.0
1.5
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
-60 -40 -20 0 20 40 60 80 100 120 140
VDD (V)
Temperature (°C)

FIGURE 38-91: Power-on Reset Rearm FIGURE 38-92: PWRT Period,


Voltage, Normal Power Mode, PIC16(L)F15356/ PIC16F15356/75/76/85/86 devices only
75/76/85/86 devices only

6
Graph represents 3ı Limits
75.0

73.0 5
-40°C
71.0
4
69.0 Typical
VOH (V)
Time (ms)

67.0
3

65.0 125°C

63.0 2

61.0
1
Typical 25°C
59.0
+ 3ı (-40°C to +125°C)
- 3ı (-40°C to +125°C)
57.0 0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 -45 -40 -35 -30 -25 -20 -15 -10 -5 0
VDD (V)
IOH (mA)

FIGURE 38-93: PWRT Period, FIGURE 38-94: VOH Vs. IOH Over
PIC16LF15356/75/76/85/86 devices only Temperature, VDD = 5.5V, PIC16F15356/75/76/
85/86 devices only

3 3.5
Graph represents 3ı Limits
Graph represents 3ı Limits
3.0

2.5
2
-40°C
2.0 Typical
VOH (V)
VOL (V)

125°C
1.5
125°C

1
Typical 1.0

-40°C
0.5

0 0.0
0 10 20 30 40 50 60 -30 -25 -20 -15 -10 -5 0
IOL (mA)
IOH (mA)

FIGURE 38-95: VOL Vs. IOL Over FIGURE 38-96: VOH Vs. IOH Over
Temperature, VDD = 5.5V, PIC16F15356/75/76/ Temperature, VDD = 3.0V
85/86 devices only

 2016-2018 Microchip Technology Inc. DS40001866A-page 560


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

3.0 2.0

Graph represents 3ı Limits


1.8
Graph represents 3ı Limits
2.5
1.6

1.4
2.0 Typical -40°C
1.2
125°C

VOH (V)
VOL (V)

1.5 1.0
125°C
Typical
0.8
1.0
0.6
-40°C
0.4
0.5
0.2

0.0 0.0
0 5 10 15 20 25 30 35 40 45 50 55 60 -8 -7.5 -7 -6.5 -6 -5.5 -5 -4.5 -4 -3.5 -3 -2.5 -2 -1.5 -1 -0.5 0

IOL (mA) IOH (mA)

FIGURE 38-97: VOL Vs. IOL Over FIGURE 38-98: VOH Vs. IOH Over
Temperature, VDD = 3.0V Temperature, VDD = 1.8V, PIC16LF15356/75/76/
85/86 devices only

1.8
18
Graph represents 3ı Limits Typical 25°C
1.6
+3ı (-40°C to +125°C)
17
1.4

1.2 16
125°C Typical -40°C
Time (us)
VOL (V)

1
15
0.8

0.6 14

0.4
13
0.2

0 12
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V)
IOL (mA)

FIGURE 38-99: VOL Vs. IOL Over FIGURE 38-100: Wake From Sleep,
Temperature, VDD = 3.0V, PIC16F15356/75/76/ VREGPM = 0, HFINTOSC = 4 MHz,
85/86 devices only PIC16F15356/75/76/85/86 devices only

120 28
Typical 25°C Typical 25°C
110 +3ı (-40°C to +125°C) 27 +3ı (-40°C to +125°C)
100
26
90
25
80
Time (us)
Time (us)

70 24

60
23
50
22
40

30 21

20 20
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V) VDD (V)

FIGURE 38-101: Wake from Sleep, FIGURE 38-102: Wake from Sleep,
VREGPM = 1, HFINTOSC = 4 MHz, VREGPM = 1, HFINTOSC = 16 MHZ,
PIC16F15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

DS40001866A-page 561  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

120 700
Typical 25°C Typical 25°C
+3ı (-40°C to +125°C)
110 650 + 3ı (-40°C to +125°C)

100 600

90 550

Time (us)
Time (us)

80 500

450
70

400
60

350
50

300
40
2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V)
VDD (V)

FIGURE 38-103: Wake from Sleep, FIGURE 38-104: Wake from Sleep,
VREGPM = 1, HFINTOSC = 16 MHz, VREGPM = 1, PIC16F15356/75/76/85/86
PIC16F15356/75/76/85/86 devices only devices only

700 700
Typical 25°C Typical 25°C
650 + 3ı (-40°C to +125°C) 650 + 3ı (-40°C to +125°C)

600 600

550 550
Time (us)

Time (us)

500 500

450 450

400 400

350 350

300 300
1.7 2.2 2.7 3.2 3.7 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6
VDD (V) VDD (V)

FIGURE 38-105: Wake from Sleep, FIGURE 38-106: Wake from Sleep,
PIC16LF15356/75/76/85/86 devices only VREGPM = 1, LFINTOSC, PIC16F15356/75/76/
85/86 devices only

700 4.2
Typical 25°C
650 + 3ı (-40°C to +125°C)

600 4.1

550
Time (us)

Time (ms)

500 4.0

450

400 3.9

Typical 25°C
350 +3ı (-40°C to +125°C)
-3ı (-40°C to +125°C)
300 3.8
1.7 2.2 2.7 3.2 3.7 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

VDD (V) VDD (V)

FIGURE 38-107: Wake from Sleep, FIGURE 38-108: Watchdog Timer Time-out
LFINTOSC, PIC16LF15356/75/76/85/86 devices Period, PIC16F15356/75/76/85/86 devices only
only

 2016-2018 Microchip Technology Inc. DS40001866A-page 562


PIC16(L)F15356/75/76/85/86
Note: Unless otherwise noted, VIN = 5V, FOSC = 300 kHz, CIN = 0.1 µF, TA = 25°C.

300.0
4.2
Typical 25°C
+ 3ı (-40°C to +125°C)
250.0
- 3ı (-40°C to +125°C)

Pull-Up Current (uA)


4.1
200.0
Time (ms)

4.0 150.0

100.0

3.9

Typical 25°C 50.0


+3ı (-40°C to +125°C)
-3ı (-40°C to +125°C)
3.8 0.0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7
VDD (V) VDD (V)

FIGURE 38-109: Watchdog Timer Time-out FIGURE 38-110: Weak Pull-up Current,
Period, PIC16LF15356/75/76/85/86 devices only PIC16F15356/75/76/85/86 devices only

180.0 -3.450
Typical 25°C
160.0 -3.500
+ 3ı (-40°C to +125°C)
- 3ı (-40°C to +125°C) Typical
140.0
Pull-Up Current (uA)

-3.550
+3 Sigma
120.0 -3.600 -3 Sigma
Slope (mV/C)

100.0 -3.650

80.0 -3.700

60.0 -3.750

40.0 -3.800

20.0 -3.850

0.0 -3.900
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 -60 -40 -20 0 20 40 60 80 100 120 140

VDD (V) Temperature (oC)

FIGURE 38-111: Weak Pull-up Current, FIGURE 38-112: High Range Temperature
PIC16LF15356/75/76/85/86 devices only Indicator Voltage Sensitivity Across Temperature

-2.300

-2.350
Typical
+3 Sigma
-2.400
-3 Sigma
Slope (mV/C)

-2.450

-2.500

-2.550

-2.600
-60 -40 -20 0 20 40 60 80 100 120 140

Temperature (oC)

FIGURE 38-113: Low Range Temperature


Indicator Voltage Sensitivity Across Temperature

DS40001866A-page 563  2016-2018 Microchip Technology Inc.


PIC16(L)F15356/75/76/85/86
39.0 DEVELOPMENT SUPPORT 39.1 MPLAB X Integrated Development
Environment Software
The PIC® microcontrollers (MCU) and dsPIC® digital
signal controllers (DSC) are supported with a full range The MPLAB X IDE is a single, unified graphical user
of software and hardware development tools: interface for Microchip and third-party software, and
• Integrated Development Environment hardware development tool that runs on Windows®,
Linux and Mac OS® X. Based on the NetBeans IDE,
- MPLAB® X IDE Software
MPLAB X IDE is an entirely new IDE with a host of free
- MPLAB® XPRESS IDE Software software components and plug-ins for high-
• Compilers/Assemblers/Linkers performance application development and debugging.
- MPLAB XC Compiler Moving between tools and upgrading from software
- MPASMTM Assembler simulators to hardware debugging and programming
- MPLINKTM Object Linker/ tools is simple with the seamless user interface.
MPLIBTM Object Librarian With complete project management, visual call graphs,
- MPLAB Assembler/Linker/Librarian for a configurable watch window and a feature-rich editor
Various Device Families that includes code completion and context menus,
• Simulators MPLAB X IDE is flexible and friendly enough for new
users. With the ability to support multiple tools on
- MPLAB X SIM Software Simulator
multiple projects with simultaneous debugging, MPLAB
• Emulators X IDE is also suitable for the needs of experienced
- MPLAB REAL ICE™ In-Circuit Emulator users.
• In-Circuit Debuggers/Programmers Feature-Rich Editor:
- MPLAB ICD 3
• Color syntax highlighting
- PICkit™ 3
• Smart code completion makes suggestions and
• Device Programmers provides hints as you type
- MPLAB PM3 Device Programmer • Automatic code formatting based on user-defined
• Low-Cost Demonstration/Development Boards, rules
Evaluation Kits and Starter Kits • Live parsing
• Third-party development tools
User-Friendly, Customizable Interface:
• Fully customizable interface: toolbars, toolbar
buttons, windows, window placement, etc.
• Call graph window
Project-Based Workspaces:
• Multiple projects
• Multiple tools
• Multiple configurations
• Simultaneous debugging sessions
File History and Bug Tracking:
• Local file history feature
• Built-in support for Bugzilla issue tracker

 2016-2018 Microchip Technology Inc. DS40001866B-page 564


PIC16(L)F15356/75/76/85/86
39.2 MPLAB XC Compilers 39.4 MPLINK Object Linker/
The MPLAB XC Compilers are complete ANSI C
MPLIB Object Librarian
compilers for all of Microchip’s 8, 16, and 32-bit MCU The MPLINK Object Linker combines relocatable
and DSC devices. These compilers provide powerful objects created by the MPASM Assembler. It can link
integration capabilities, superior code optimization and relocatable objects from precompiled libraries, using
ease of use. MPLAB XC Compilers run on Windows, directives from a linker script.
Linux or MAC OS X.
The MPLIB Object Librarian manages the creation and
For easy source level debugging, the compilers provide modification of library files of precompiled code. When
debug information that is optimized to the MPLAB X a routine from a library is called from a source file, only
IDE. the modules that contain that routine will be linked in
The free MPLAB XC Compiler editions support all with the application. This allows large libraries to be
devices and commands, with no time or memory used efficiently in many different applications.
restrictions, and offer sufficient code optimization for The object linker/library features include:
most applications.
• Efficient linking of single libraries instead of many
MPLAB XC Compilers include an assembler, linker and smaller files
utilities. The assembler generates relocatable object • Enhanced code maintainability by grouping
files that can then be archived or linked with other relo- related modules together
catable object files and archives to create an execut-
• Flexible creation of libraries with easy module
able file. MPLAB XC Compiler uses the assembler to
listing, replacement, deletion and extraction
produce its object file. Notable features of the assem-
bler include:
39.5 MPLAB Assembler, Linker and
• Support for the entire device instruction set
Librarian for Various Device
• Support for fixed-point and floating-point data
Families
• Command-line interface
• Rich directive set MPLAB Assembler produces relocatable machine
• Flexible macro language code from symbolic assembly language for PIC24,
PIC32 and dsPIC DSC devices. MPLAB XC Compiler
• MPLAB X IDE compatibility
uses the assembler to produce its object file. The
assembler generates relocatable object files that can
39.3 MPASM Assembler then be archived or linked with other relocatable object
The MPASM Assembler is a full-featured, universal files and archives to create an executable file. Notable
macro assembler for PIC10/12/16/18 MCUs. features of the assembler include:

The MPASM Assembler generates relocatable object • Support for the entire device instruction set
files for the MPLINK Object Linker, Intel® standard HEX • Support for fixed-point and floating-point data
files, MAP files to detail memory usage and symbol • Command-line interface
reference, absolute LST files that contain source lines • Rich directive set
and generated machine code, and COFF files for • Flexible macro language
debugging.
• MPLAB X IDE compatibility
The MPASM Assembler features include:
• Integration into MPLAB X IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multipurpose
source files
• Directives that allow complete control over the
assembly process

 2016-2018 Microchip Technology Inc. DS40001866B-page 565


PIC16(L)F15356/75/76/85/86
39.6 MPLAB X SIM Software Simulator 39.8 MPLAB ICD 3 In-Circuit Debugger
The MPLAB X SIM Software Simulator allows code
System
development in a PC-hosted environment by simulat- The MPLAB ICD 3 In-Circuit Debugger System is
ing the PIC MCUs and dsPIC DSCs on an instruction Microchip’s most cost-effective, high-speed hardware
level. On any given instruction, the data areas can be debugger/programmer for Microchip Flash DSC and
examined or modified and stimuli can be applied from MCU devices. It debugs and programs PIC Flash
a comprehensive stimulus controller. Registers can be microcontrollers and dsPIC DSCs with the powerful,
logged to files for further run-time analysis. The trace yet easy-to-use graphical user interface of the MPLAB
buffer and logic analyzer display extend the power of IDE.
the simulator to record and track program execution,
The MPLAB ICD 3 In-Circuit Debugger probe is
actions on I/O, most peripherals and internal registers.
connected to the design engineer’s PC using a high-
The MPLAB X SIM Software Simulator fully supports speed USB 2.0 interface and is connected to the target
symbolic debugging using the MPLAB XC Compilers, with a connector compatible with the MPLAB ICD 2 or
and the MPASM and MPLAB Assemblers. The soft- MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3
ware simulator offers the flexibility to develop and supports all MPLAB ICD 2 headers.
debug code outside of the hardware laboratory envi-
ronment, making it an excellent, economical software 39.9 PICkit 3 In-Circuit Debugger/
development tool.
Programmer
39.7 MPLAB REAL ICE In-Circuit The MPLAB PICkit 3 allows debugging and program-
Emulator System ming of PIC and dsPIC Flash microcontrollers at a most
affordable price point using the powerful graphical user
The MPLAB REAL ICE In-Circuit Emulator System is interface of the MPLAB IDE. The MPLAB PICkit 3 is
Microchip’s next generation high-speed emulator for connected to the design engineer’s PC using a full-
Microchip Flash DSC and MCU devices. It debugs and speed USB interface and can be connected to the tar-
programs all 8, 16 and 32-bit MCU, and DSC devices get via a Microchip debug (RJ-11) connector (compati-
with the easy-to-use, powerful graphical user interface of ble with MPLAB ICD 3 and MPLAB REAL ICE). The
the MPLAB X IDE. connector uses two device I/O pins and the Reset line
The emulator is connected to the design engineer’s to implement in-circuit debugging and In-Circuit Serial
PC using a high-speed USB 2.0 interface and is Programming™ (ICSP™).
connected to the target with either a connector
compatible with in-circuit debugger systems (RJ-11) 39.10 MPLAB PM3 Device Programmer
or with the new high-speed, noise tolerant, Low-
Voltage Differential Signal (LVDS) interconnection The MPLAB PM3 Device Programmer is a universal,
(CAT5). CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
The emulator is field upgradeable through future firm- maximum reliability. It features a large LCD display
ware downloads in MPLAB X IDE. MPLAB REAL ICE (128 x 64) for menus and error messages, and a mod-
offers significant advantages over competitive emulators ular, detachable socket assembly to support various
including full-speed emulation, run-time variable package types. The ICSP cable assembly is included
watches, trace analysis, complex breakpoints, logic as a standard item. In Stand-Alone mode, the MPLAB
probes, a ruggedized probe interface and long (up to PM3 Device Programmer can read, verify and program
three meters) interconnection cables. PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices, and incorporates an MMC card for file
storage and data applications.

 2016-2018 Microchip Technology Inc. DS40001866B-page 566


PIC16(L)F15356/75/76/85/86
39.11 Demonstration/Development 39.12 Third-Party Development Tools
Boards, Evaluation Kits, and Microchip also offers a great collection of tools from
Starter Kits third-party vendors. These tools are carefully selected
A wide variety of demonstration, development and to offer good value and unique functionality.
evaluation boards for various PIC MCUs and dsPIC • Device Programmers and Gang Programmers
DSCs allows quick application development on fully from companies, such as SoftLog and CCS
functional systems. Most boards include prototyping • Software Tools from companies, such as Gimpel
areas for adding custom circuitry and provide applica- and Trace Systems
tion firmware and source code for examination and • Protocol Analyzers from companies, such as
modification. Saleae and Total Phase
The boards support a variety of features, including LEDs, • Demonstration Boards from companies, such as
temperature sensors, switches, speakers, RS-232 MikroElektronika, Digilent® and Olimex
interfaces, LCD displays, potentiometers and additional • Embedded Ethernet Solutions from companies,
EEPROM memory. such as EZ Web Lynx, WIZnet and IPLogika®
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™
demonstration/development board series of circuits,
Microchip has a line of evaluation kits and demonstra-
tion software for analog filter design, KEELOQ® security
ICs, CAN, IrDA®, PowerSmart battery management,
SEEVAL® evaluation system, Sigma-Delta ADC, flow
rate sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.

 2016-2018 Microchip Technology Inc. DS40001866B-page 567


PIC16(L)F15356/75/76/85/86
40.0 PACKAGING INFORMATION
40.1 Package Marking Information

28-Lead SPDIP (.300”) Example

PIC16F15356
/SP e3
1525017

28-Lead SOIC (7.50 mm) Example

XXXXXXXXXXXXXXXXXXXX PIC16LF15356
XXXXXXXXXXXXXXXXXXXX /SO e3
XXXXXXXXXXXXXXXXXXXX
YYWWNNN 1525017

28-Lead SSOP (5.30 mm) Example

PIC16F15356
/SS e3
1525017

Legend: XX...X Customer-specific information


Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
* This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 568


PIC16(L)F15356/75/76/85/86

40.1 Package Marking Information (Continued)

28-Lead UQFN (4x4x0.5 mm) and 28-Lead QFN (6x6 mm) Example

PIN 1 PIN 1 PIC16


F15356
/MV e3

525017

Legend: XX...X Customer-specific information


Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
* This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 569


PIC16(L)F15356/75/76/85/86

40.1 Package Marking Information (Continued)

40-Lead PDIP (600 mil) Example

XXXXXXXXXXXXXXXXXX PIC16F15375
XXXXXXXXXXXXXXXXXX /P e3
XXXXXXXXXXXXXXXXXX
YYWWNNN 1525017

40-Lead UQFN (5x5x0.5 mm) Example

PIN 1 PIN 1
PIC16
LF15375
/MV e 3

1525017
28-Lead QFN (6x6 mm) Example

PIN 1 PIN 1
XXXXXXXX PIC16
XXXXXXXX
LF15375
/MV
YYWWNNN 1525017

Legend: XX...X Customer-specific information


Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
* This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 570


PIC16(L)F15356/75/76/85/86

40.1 Package Marking Information (Continued)

44-Lead TQFP (10x10x1 mm) Example

XXXXXXXXXX 16F15376
XXXXXXXXXX /PT e3
XXXXXXXXXX
YYWWNNN 1525017

44-Lead QFN (8x8x0.9 mm) Example

PIN 1 PIN 1
XXXXXXXXXXX 16LF15376
XXXXXXXXXXX /ML
XXXXXXXXXXX
YYWWNNN 1525017

Legend: XX...X Customer-specific information


Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
* This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 571


PIC16(L)F15356/75/76/85/86
40.1 Package Marking Information (Continued)

48-Lead UQFN (6x6x0.5 mm) Example

PIN 1 PIN 1

XXXXXXXX 16F15386
XXXXXXXX /MV e3
YYWWNNN 1525017

48-Lead TQFP (7x7x1 mm) Example

XXXXXXX 16F15386
XXXYYWW /PT1525 e3
NNN 017

Legend: XX...X Customer-specific information


Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
* This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.

 2016-2018 Microchip Technology Inc. DS40001866B-page 572


PIC16(L)F15356/75/76/85/86
The following sections give the technical details of the packages.

       
      
!
"# J
* + #* $

*  K%
6#/ ##* 
 ! K  ' *  *%*
** HVV666+
  +V  K

NOTE 1
E1

1 2 3

A A2

L c

A1 b1
b e eB

X*# Y9[?
+# \+*# Y Y] ^
Y$+5
 '!# Y _
!*  G9
 * *!  ` ` 
 %%! K  K##   ; 
G#* *!   ` `
 $%
*  $%
j%* ?  ; ;;
 %%! Kj%* ?  _ 
]"
\*  ; ;{ 
 * *! \  ; 
\%  K## _  
X 
\%j%* 5   
\ 6
\%j%* 5  _ 
]"
 6  7 G ` ` ;
"#
 !"#$%&'*$
+"
/5$*+$#*5 *%6* *  * %

 7' *9 
 *
#* 
; +# #%?%  * $%+ %'# 

*
$# # %'# 

*
$# ##  *& %@ 
#%
 +# %* 
  
?B
G9H G# +#  
* & *"$# 66* $** 
 #


     
6 9G

 2016-2018 Microchip Technology Inc. DS40001866B-page 573


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 574


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 575


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 576


PIC16(L)F15356/75/76/85/86

  
$%
 &  

  '*   

&!
"# J
* + #* $

*  K%
6#/ ##* 
 ! K  ' *  *%*
** HVV666+
  +V  K

D
N

E
E1

1 2
b
NOTE 1
e

c
A A2

φ
A1
L1 L

X*# \\??
+# \+*# Y Y] ^
Y$+5
 '!# Y _
!*  {G9
]"
[ *  ` ` 
 %%! K  K##  {  _
*% ''   ` `
]"
j%* ?  _ _
 %%! Kj%* ?  ; {
]"
\*    
J *\* \   
J *
* \ ?J
\%  K##  ` 
J *  | | _|
\%j%* 5  ` ;_
"#
 !"#$%&'*$
+"
/5$*+$#*5 *%6* *  * %

 +# #%?%  * $%+ %'# 

*
$# # %'# 

*
$# ##  *& %++ 
#%
; +# %* 
  
?B
G9H G# +#  
* & *"$# 66* $** 
 #
?JH '
 +# /$#$6* $** 
 /'
'
+*  $
## 


     
6 9;G

 2016-2018 Microchip Technology Inc. DS40001866B-page 577


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 578


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 579


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 580


PIC16(L)F15356/75/76/85/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 581


PIC16(L)F15356/75/76/85/86

+         ,    !


"# J
* + #* $

*  K%
6#/ ##* 
 ! K  ' *  *%*
** HVV666+
  +V  K

NOTE 1
E1

1 2 3

A A2
L c
b1
A1
b e eB

X*# Y9[?
+# \+*# Y Y] ^
Y$+5
 '!# Y 
!*  G9
 * *!  ` ` 
 %%! K  K##   ` 
G#* *!   ` `
 $%
*  $%
j%* ?  ` {
 %%! Kj%* ? _ ` _
]"
\*  _ ` 
 * *! \  ` 
\%  K## _ ` 
X 
\%j%* 5 ; ` 
\ 6
\%j%* 5  ` ;
]"
 6  7 G ` ` 
"#
 !"#$%&'*$
+"
/5$*+$#*5 *%6* *  * %

 7' *9 
 *
#* 
; +# #%?%  * $%+ %'# 

*
$# # %'# 

*
$# ##  *& %@ 
#%
 +# %* 
  
?B
G9H G# +#  
* & *"$# 66* $** 
 #


     
6 9{G

 2016-2018 Microchip Technology Inc. DS40001866B-page 582


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 583


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 584


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 585


PIC16(L)F15356/75/76/85/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 586


PIC16(L)F15356/75/76/85/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 587


PIC16(L)F15356/75/76/85/86

   4 57 "   9 ;  ,<,   45"!
= $ *''  >   9$
"# J
* + #* $

*  K%
6#/ ##* 
 ! K  ' *  *%*
** HVV666+
  +V  K

 2016-2018 Microchip Technology Inc. DS40001866B-page 588


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Thin Quad Flatpack (PT) - 10x10x1.0 mm Body [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

D A
D1 B
NOTE 2

(DATUM A)
(DATUM B)
E1 E
NOTE 1 A A

2X
N
0.20 H A B

2X 1 2 3
0.20 H A B 4X 11 TIPS
TOP VIEW
0.20 C A B

A A2
C

SEATING PLANE
0.10 C A1
SIDE VIEW
1 2 3

NOTE 1

44 X b
e 0.20 C A B

BOTTOM VIEW
Microchip Technology Drawing C04-076C Sheet 1 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 589


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Thin Quad Flatpack (PT) - 10x10x1.0 mm Body [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

L θ

(L1)
SECTION A-A

Units MILLIMETERS
Dimension Limits MIN NOM MAX
Number of Leads N 44
Lead Pitch e 0.80 BSC
Overall Height A - - 1.20
Standoff A1 0.05 - 0.15
Molded Package Thickness A2 0.95 1.00 1.05
Overall Width E 12.00 BSC
Molded Package Width E1 10.00 BSC
Overall Length D 12.00 BSC
Molded Package Length D1 10.00 BSC
Lead Width b 0.30 0.37 0.45
Lead Thickness c 0.09 - 0.20
Lead Length L 0.45 0.60 0.75
Footprint L1 1.00 REF
Foot Angle θ 0° 3.5° 7°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Exact shape of each corner is optional.
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.

Microchip Technology Drawing C04-076C Sheet 2 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 590


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Thin Quad Flatpack (PT) - 10X10X1 mm Body, 2.00 mm Footprint [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

C1
44

1
2

G
C2

Y1

X1 E
SILK SCREEN

RECOMMENDED LAND PATTERN

Units MILLIMETERS
Dimension Limits MIN NOM MAX
Contact Pitch E 0.80 BSC
Contact Pad Spacing C1 11.40
Contact Pad Spacing C2 11.40
Contact Pad Width (X44) X1 0.55
Contact Pad Length (X44) Y1 1.50
Distance Between Pads G 0.25
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing No. C04-2076B

 2016-2018 Microchip Technology Inc. DS40001866B-page 591


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

D A B
N
NOTE 1
1
2

E
(DATUM B)
(DATUM A)
2X
0.20 C

2X
0.20 C TOP VIEW

0.10 C A1
C
SEATING A
PLANE 44X
A3 0.08 C
SIDE VIEW
L
0.10 C A B
D2

0.10 C A B

E2

K
2
1

NOTE 1 N
44X b
e 0.07 C A B
0.05 C
BOTTOM VIEW
Microchip Technology Drawing C04-103D Sheet 1 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 592


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

Units MILLIMETERS
Dimension Limits MIN NOM MAX
Number of Pins N 44
Pitch e 0.65 BSC
Overall Height A 0.80 0.90 1.00
Standoff A1 0.00 0.02 0.05
Terminal Thickness A3 0.20 REF
Overall Width E 8.00 BSC
Exposed Pad Width E2 6.25 6.45 6.60
Overall Length D 8.00 BSC
Exposed Pad Length D2 6.25 6.45 6.60
Terminal Width b 0.20 0.30 0.35
Terminal Length L 0.30 0.40 0.50
Terminal-to-Exposed-Pad K 0.20 - -
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.

Microchip Technology Drawing C04-103D Sheet 2 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 593


PIC16(L)F15356/75/76/85/86

44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

C1
X2
EV
44
G2
1
2
ØV
EV
C2 Y2
G1

Y1

E SILK SCREEN
X1

RECOMMENDED LAND PATTERN


Units MILLIMETERS
Dimension Limits MIN NOM MAX
Contact Pitch E 0.65 BSC
Optional Center Pad Width X2 6.60
Optional Center Pad Length Y2 6.60
Contact Pad Spacing C1 8.00
Contact Pad Spacing C2 8.00
Contact Pad Width (X44) X1 0.35
Contact Pad Length (X44) Y1 0.85
Contact Pad to Contact Pad (X40) G1 0.30
Contact Pad to Center Pad (X44) G2 0.28
Thermal Via Diameter V 0.33
Thermal Via Pitch EV 1.20
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during
reflow process

Microchip Technology Drawing No. C04-2103C

 2016-2018 Microchip Technology Inc. DS40001866B-page 594


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 595


PIC16(L)F15356/75/76/85/86

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

 2016-2018 Microchip Technology Inc. DS40001866B-page 596


PIC16(L)F15356/75/76/85/86

 2016-2018 Microchip Technology Inc. DS40001866B-page 597


PIC16(L)F15356/75/76/85/86

48-Lead Thin Quad Flatpack (PT) - 7x7x1.0 mm Body [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

48X TIPS
0.20 C A-B D
D
D1
D1
2

A B

E1 E

E1
A A 2

E1
4 N

NOTE 1 1 2 4X
D1 0.20 H A-B D
4

48x b
e 0.08 C A-B D

TOP VIEW

0.10 C H
C A2
A
SEATING
PLANE 0.08 C

A1 SIDE VIEW

Microchip Technology Drawing C04-300-PT Rev A Sheet 1 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 598


PIC16(L)F15356/75/76/85/86

48-Lead Thin Quad Flatpack (PT) - 7x7x1.0 mm Body [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

E T
L
(L1)

SECTION A-A

Units MILLIMETERS
Dimension Limits MIN NOM MAX
Number of Leads N 48
Lead Pitch e 0.50 BSC
Overall Height A - - 1.20
Standoff A1 0.05 - 0.15
Molded Package Thickness A2 0.95 1.00 1.05
Foot Length L 0.45 0.60 0.75
Footprint L1 1.00 REF
Foot Angle I 0° 3.5° 7°
Overall Width E 9.00 BSC
Overall Length D 9.00 BSC
Molded Package Width E1 7.00 BSC
Molded Package Length D1 7.00 BSC
Lead Thickness c 0.09 - 0.16
Lead Width b 0.17 0.22 0.27
Mold Draft Angle Top D 11° 12° 13°
Mold Draft Angle Bottom E 11° 12° 13°

Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.25mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
5. Datums A-B and D to be determined at center line between leads where leads exit
plastic body at datum plane H
Microchip Technology Drawing C04-300-PT Rev A Sheet 2 of 2

 2016-2018 Microchip Technology Inc. DS40001866B-page 599


PIC16(L)F15356/75/76/85/86

48-Lead Thin Quad Flatpack (PT) - 7x7x1.0 mm Body [TQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging

C1

C2 G

SILK SCREEN
48

Y1

1 2
X1
E

RECOMMENDED LAND PATTERN

Units MILLIMETERS
Dimension Limits MIN NOM MAX
Contact Pitch E 0.50 BSC
Contact Pad Spacing C1 8.40
Contact Pad Spacing C2 8.40
Contact Pad Width (X48) X1 0.30
Contact Pad Length (X48) Y1 1.50
Distance Between Pads G 0.20
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during
reflow process

Microchip Technology Drawing C04-2300-PT Rev A

 2016-2018 Microchip Technology Inc. DS40001866B-page 600


PIC16(L)F15356/75/76/85/86
APPENDIX A: DATA SHEET
REVISION HISTORY

Revision A (12/2016)
Initial release of the document.

Revision B (07/2018)
Updated Register 5-4 and 20-3 (ADACT). Updated
Equation 19-1 (sensor temperature), Updated Register
18-1 (FVRCON), Updated 19.2.1.1, Removed Exam-
ple 19-1 (Temp Sens),
Replaced PGC/PGD with ICSPCLK/ICSPDAT;
Revised Section 9.2.2.3 LFINSTOSC; Revised Table 4-
5, 15-1 and 15-2 (PPS Input Signal Routing Options);
Table 15-6 Summary of Registers/PPS Module;
Revised Example 20-1 ADC Conversion; Added note
to Section 20.1.2 Channel Selection; Revised Section
27.0 Timer2 Module; Table 37-11, revised RST06.

 2016-2018 Microchip Technology Inc. DS40001866B-page 601


PIC16(L)F15356/75/76/85/86
THE MICROCHIP WEBSITE CUSTOMER SUPPORT
Microchip provides online support via our website at Users of Microchip products can receive assistance
www.microchip.com. This website is used as a means through several channels:
to make files and information easily available to • Distributor or Representative
customers. Accessible by using your favorite Internet
• Local Sales Office
browser, the website contains the following information:
• Field Application Engineer (FAE)
• Product Support – Data sheets and errata, appli-
• Technical Support
cation notes and sample programs, design
resources, user’s guides and hardware support Customers should contact their distributor, representa-
documents, latest software releases and archived tive or Field Application Engineer (FAE) for support.
software Local sales offices are also available to help custom-
• General Technical Support – Frequently Asked ers. A listing of sales offices and locations is included in
Questions (FAQ), technical support requests, the back of this document.
online discussion groups, Microchip consultant Technical support is available through the website
program member listing at: http://www.microchip.com/support
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of Micro-
chip sales offices, distributors and factory repre-
sentatives

CUSTOMER CHANGE NOTIFICATION


SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a spec-
ified product family or development tool of interest.
To register, access the Microchip website at
www.microchip.com. Under “Support”, click on “Cus-
tomer Change Notification” and follow the registration
instructions.

 2016-2018 Microchip Technology Inc. DS40001866B-page 602


PIC16(L)F15356/75/76/85/86
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO. [X](1) - X /XX XXX
Examples:
Device Tape and Reel Temperature Package Pattern a) PIC16F15356- E/P
Option Range Extended temperature
PDIP package

Device: PIC16F15356, PIC16LF15356


PIC16F15375, PIC16LF15375
PIC16F15376, PIC16LF15376
PIC16F15385, PIC16LF15385
PIC16F15386, PIC16LF15386

Tape and Reel Blank = Standard packaging (tube or tray)


Option: T = Tape and Reel(1)

Temperature I = -40C to +85C (Industrial)


Range: E = -40C to +125C (Extended)
Note 1: Tape and Reel identifier only appears in
the catalog part number description. This
identifier is used for ordering purposes and
Package:(2) ML = 44-lead QFN 8x8mm
MV = 28-lead UQFN 4x4mm is not printed on the device package.
MV = 40-lead UQFN 5x5mm Check with your Microchip Sales Office
MV = 48-lead UQFN 6x6mm for package availability with the Tape and
P = 40-lead PDIP Reel option.
PT = 44-lead TQFP 10x10mm 2: Small form-factor packaging options may
PT = 48-lead TQFP 7x7mm be available. Check
SO = 28-lead SOIC
SP = 28-lead SPDIP www.microchip.com/packaging for small-
SS = 28-lead SSOP form factor package availability, or contact
ML = 28-lead QFN 6x6mm your local Sales Office.

Pattern: QTP, SQTP, Code or Special Requirements


(blank otherwise)

 2016-2018 Microchip Technology Inc. DS40001866B-page 603


PIC16(L)F15356/75/76/85/86

Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Information contained in this publication regarding device Trademarks


applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, AnyRate, AVR,
and may be superseded by updates. It is your responsibility to AVR logo, AVR Freaks, BeaconThings, BitCloud, chipKIT, chipKIT
ensure that your application meets with your specifications. logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR,
MICROCHIP MAKES NO REPRESENTATIONS OR Heldo, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, LINK
WARRANTIES OF ANY KIND WHETHER EXPRESS OR MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST
IMPLIED, WRITTEN OR ORAL, STATUTORY OR logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32
OTHERWISE, RELATED TO THE INFORMATION, logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC,
INCLUDING BUT NOT LIMITED TO ITS CONDITION, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are
QUALITY, PERFORMANCE, MERCHANTABILITY OR registered trademarks of Microchip Technology Incorporated in
FITNESS FOR PURPOSE. Microchip disclaims all liability the U.S.A. and other countries.
arising from this information and its use. Use of Microchip ClockWorks, The Embedded Control Solutions Company,
devices in life support and/or safety applications is entirely at EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
the buyer’s risk, and the buyer agrees to defend, indemnify and mTouch, Precision Edge, and Quiet-Wire are registered
hold harmless Microchip from any and all damages, claims, trademarks of Microchip Technology Incorporated in the U.S.A.
suits, or expenses resulting from such use. No licenses are Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
conveyed, implicitly or otherwise, under any Microchip Capacitor, AnyIn, AnyOut, BodyCom, CodeGuard,
intellectual property rights unless otherwise stated. CryptoAuthentication, CryptoCompanion, CryptoController,
dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM,
ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-
Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi,
MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB,
MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation,
PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix,
RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial
Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II,
Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and Silicon Storage Technology is a registered trademark of Microchip
Tempe, Arizona; Gresham, Oregon and design centers in California Technology Inc. in other countries.
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping GestIC is a registered trademark of Microchip Technology
devices, Serial EEPROMs, microperipherals, nonvolatile memory and Germany II GmbH & Co. KG, a subsidiary of Microchip Technology
analog products. In addition, Microchip’s quality system for the design Inc., in other countries.
and manufacture of development systems is ISO 9001:2000 certified.
All other trademarks mentioned herein are property of their
respective companies.

QUALITY MANAGEMENT SYSTEM © 2018, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-3330-9
CERTIFIED BY DNV
== ISO/TS 16949 ==

 2016-2018 Microchip Technology Inc. DS40001866B-page 604


Worldwide Sales and Service
AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE
Corporate Office Australia - Sydney India - Bangalore Austria - Wels
2355 West Chandler Blvd. Tel: 61-2-9868-6733 Tel: 91-80-3090-4444 Tel: 43-7242-2244-39
Chandler, AZ 85224-6199 China - Beijing India - New Delhi Fax: 43-7242-2244-393
Tel: 480-792-7200 Tel: 86-10-8569-7000 Tel: 91-11-4160-8631 Denmark - Copenhagen
Fax: 480-792-7277 Tel: 45-4450-2828
China - Chengdu India - Pune
Technical Support: Fax: 45-4485-2829
Tel: 86-28-8665-5511 Tel: 91-20-4121-0141
http://www.microchip.com/
China - Chongqing Japan - Osaka Finland - Espoo
support
Tel: 86-23-8980-9588 Tel: 81-6-6152-7160 Tel: 358-9-4520-820
Web Address:
www.microchip.com China - Dongguan Japan - Tokyo France - Paris
Tel: 86-769-8702-9880 Tel: 81-3-6880- 3770 Tel: 33-1-69-53-63-20
Atlanta Fax: 33-1-69-30-90-79
Duluth, GA China - Guangzhou Korea - Daegu
Tel: 678-957-9614 Tel: 86-20-8755-8029 Tel: 82-53-744-4301 Germany - Garching
Tel: 49-8931-9700
Fax: 678-957-1455 China - Hangzhou Korea - Seoul
Austin, TX Tel: 86-571-8792-8115 Tel: 82-2-554-7200 Germany - Haan
Tel: 512-257-3370 Tel: 49-2129-3766400
China - Hong Kong SAR Malaysia - Kuala Lumpur
Tel: 852-2943-5100 Tel: 60-3-7651-7906 Germany - Heilbronn
Boston
Tel: 49-7131-67-3636
Westborough, MA China - Nanjing Malaysia - Penang
Tel: 774-760-0087 Tel: 86-25-8473-2460 Tel: 60-4-227-8870 Germany - Karlsruhe
Fax: 774-760-0088 Tel: 49-721-625370
China - Qingdao Philippines - Manila
Chicago Tel: 86-532-8502-7355 Tel: 63-2-634-9065 Germany - Munich
Itasca, IL Tel: 49-89-627-144-0
China - Shanghai Singapore
Tel: 630-285-0071 Fax: 49-89-627-144-44
Tel: 86-21-3326-8000 Tel: 65-6334-8870
Fax: 630-285-0075 Germany - Rosenheim
China - Shenyang Taiwan - Hsin Chu
Dallas Tel: 49-8031-354-560
Tel: 86-24-2334-2829 Tel: 886-3-577-8366
Addison, TX Israel - Ra’anana
China - Shenzhen Taiwan - Kaohsiung
Tel: 972-818-7423 Tel: 86-755-8864-2200 Tel: 886-7-213-7830 Tel: 972-9-744-7705
Fax: 972-818-2924 Italy - Milan
China - Suzhou Taiwan - Taipei
Detroit Tel: 39-0331-742611
Tel: 86-186-6233-1526 Tel: 886-2-2508-8600
Novi, MI Fax: 39-0331-466781
Tel: 248-848-4000 China - Wuhan Thailand - Bangkok
Tel: 86-27-5980-5300 Tel: 66-2-694-1351 Italy - Padova
Houston, TX Tel: 39-049-7625286
Tel: 281-894-5983 China - Xian Vietnam - Ho Chi Minh
Tel: 86-29-8833-7252 Tel: 84-28-5448-2100 Netherlands - Drunen
Indianapolis Tel: 31-416-690399
Noblesville, IN China - Xiamen Fax: 31-416-690340
Tel: 86-592-2388138
Tel: 317-773-8323 Norway - Trondheim
Fax: 317-773-5453 China - Zhuhai Tel: 47-7289-7561
Tel: 317-536-2380 Tel: 86-756-3210040
Poland - Warsaw
Los Angeles Tel: 48-22-3325737
Mission Viejo, CA
Romania - Bucharest
Tel: 949-462-9523 Tel: 40-21-407-87-50
Fax: 949-462-9608
Tel: 951-273-7800 Spain - Madrid
Tel: 34-91-708-08-90
Raleigh, NC Fax: 34-91-708-08-91
Tel: 919-844-7510
Sweden - Gothenberg
New York, NY Tel: 46-31-704-60-40
Tel: 631-435-6000
Sweden - Stockholm
San Jose, CA Tel: 46-8-5090-4654
Tel: 408-735-9110
Tel: 408-436-4270 UK - Wokingham
Tel: 44-118-921-5800
Canada - Toronto Fax: 44-118-921-5820
Tel: 905-695-1980
Fax: 905-695-2078

 2016-2018 Microchip Technology Inc. DS40001866B-page 605

10/25/17

You might also like