Operation Manual

Commander Chassis
BALTIMORE COUNTY FIRE DEPARTMENT
VIN: 54F2CB51XEWM10809
Date: 2/23/2015

© 2014 Rosenbauer Motors, LLC

 Table of Contents

1 Legal notice...................................................................................................... 6
1.1 Copyright ......................................................................................... 6
1.2 Manufacturer and after sales address ............................................. 6
2 Introduction ...................................................................................................... 7
2.1 Welcome note ................................................................................. 7
2.2 Liability and injury ............................................................................ 7
2.3 Vehicle identification ........................................................................ 8
2.4 Use of the operation manual............................................................ 9
2.4.1 Validation ........................................................................ 9
2.4.2 Signs and symbols .......................................................... 9
3 Safety............................................................................................................. 11
3.1 Proper usage ................................................................................. 11
3.2 Markings and warning signs .......................................................... 11
3.3 Other regulations ........................................................................... 11
3.4 Training and qualifications ............................................................. 12
3.5 General safety instructions ............................................................ 12
3.6 List of conventional signs .............................................................. 13
3.6.1 Warning signs ............................................................... 13
3.6.2 Prohibition signs............................................................ 15
3.6.3 Mandatory safety signs ................................................. 16
3.7 Warning notes ............................................................................... 17
3.8 Safety labels .................................................................................. 26
3.9 Reporting safety defects ................................................................ 27
3.10 Material safety data sheets (MSDS) .............................................. 27
3.11 Seatbelts ....................................................................................... 27
3.12 Three points of contact rule ........................................................... 28
3.13 Do not move apparatus light .......................................................... 28
3.14 Vehicle data recorder .................................................................... 28
4 Product description ........................................................................................ 29
4.1 Vehicle side views ......................................................................... 29
4.1 Vehicle front view .......................................................................... 30
4.2 Driver’s panel view ........................................................................ 31
4.3 Driver’s kick panel view ................................................................. 31

2
5 Technical description ..................................................................................... 32
5.1 Master power disconnect switch .................................................... 32
5.2 Parking brake ................................................................................ 33
5.3 Brake and throttle pedals .............................................................. 34
5.4 Steering column controls ............................................................... 35
5.4.1 Multifunction lever ......................................................... 35
5.4.2 Tilting / telescoping lever .............................................. 35
5.4.3 Hazard light switch........................................................ 35
5.5 Dash gauges and tell-tales ............................................................ 36
5.6 Transmission controls ................................................................... 38
5.7 Heating ventilation and air conditioning (HVAC) controls ............... 39
5.7.1 Front HVAC controls ..................................................... 39
5.7.2 Rear HVAC controls ..................................................... 39
5.8 Ignition switch ............................................................................... 40
5.9 Engine start switch ........................................................................ 40
5.10 Dash panel dimmer control ........................................................... 40
5.11 Regeneration “regen” switch ......................................................... 40
5.12 Regeneration inhibit switch ........................................................... 40
5.13 Headlight and parking light controls............................................... 40
5.14 Windshield wiper controls .............................................................. 41
5.15 Window controls ............................................................................ 41
5.16 Door lock controls ......................................................................... 41
5.17 Engine brake controls.................................................................... 41
5.18 Engine high idle control ................................................................. 42
5.19 Master warning control .................................................................. 42
5.20 Power mirror controls .................................................................... 43
5.21 Vehicle data recorder .................................................................... 44
5.22 V-Mux controls .............................................................................. 45
5.22.1 Warning light activation ................................................. 45
5.22.2 Warning light menu ....................................................... 45
5.22.3 HVAC controls .............................................................. 46
5.22.4 Lighting ......................................................................... 46
5.22.5 Secondary menu........................................................... 46
5.22.6 Home ............................................................................ 47

3
 5.22.7 Seat belt status ............................................................. 47
5.22.8 Rear/side view camera.................................................. 47
6 Operation ....................................................................................................... 48
6.1 Preparation for use ........................................................................ 48
6.1.1 Before entering the apparatus ....................................... 48
6.1.2 Before driving the apparatus ......................................... 48
6.1.3 Pre-start checklist ......................................................... 49
6.2 Starting and stopping the engine ................................................... 50
6.2.1 Starting the engine ........................................................ 50
6.2.2 Stopping the engine ...................................................... 50
6.3 Driving the vehicle ......................................................................... 51
6.3.1 General information ...................................................... 51
6.3.2 Begin driving ................................................................. 52
6.3.3 Select transmission range ............................................. 52
6.3.4 Acceleration .................................................................. 53
6.3.5 Stopping and parking the vehicle .................................. 53
6.4 Braking the vehicle ........................................................................ 54
6.4.1 Brake air pressure......................................................... 54
6.4.2 Parking brake................................................................ 54
6.4.3 Service brake ................................................................ 56
6.5 Cab tilt procedure .......................................................................... 57
6.5.1 Remote electric operation ............................................. 57
6.5.2 Manual pump operation ................................................ 59
6.6 Emission control system ................................................................ 61
6.7 Diesel exhaust fluid (DEF) tank ..................................................... 65
7 Service and cleaning ...................................................................................... 66
7.1 Service plan .................................................................................. 66
7.1.1 Inspection procedures ................................................... 67
7.1.2 Oil and filter interval ...................................................... 69
7.2 Transmission maintenance ............................................................ 70
7.3 Filter information............................................................................ 71
7.4 Fluid capacities.............................................................................. 71
7.5 Under cab overview ....................................................................... 72
7.6 Engine oil level .............................................................................. 73

4
 7.7 Engine cooling system .................................................................. 73
7.8 Transmission fluid level ................................................................. 74
7.9 Power steering fluid level .............................................................. 75
7.10 Fuel filter/water separator .............................................................. 75
7.11 Windshield wipers and washer fluid............................................... 75
7.12 Batteries ........................................................................................ 76
7.13 Engine air filter .............................................................................. 76
7.14 Tires and wheels ........................................................................... 77
7.15 Normal operating range................................................................. 79
7.16 Engine belt routing diagram........................................................... 79
7.17 Spare parts list and wiring diagrams.............................................. 79
7.18 Maintenance and repair record...................................................... 80
7.19 Cleaning and washing ................................................................... 81
8 Troubleshooting ............................................................................................. 82
8.1 General troubleshooting ................................................................ 82
8.2 Cab tilt troubleshooting.................................................................. 83
8.2.1 Cab tilt pump fuse location ............................................ 83
8.3 Fuse panel diagram ...................................................................... 84
9 Environmental protection ............................................................................... 85
9.1 Disposal of hazardous substances ................................................ 85
10 Technical data ............................................................................................... 86
10.1 Chassis specifications ................................................................... 86
10.2 Engine specifications..................................................................... 86
10.3 Warranty and registration .............................................................. 87
10.3.1 Warranty procedures .................................................... 87
10.3.2 Cab and chassis limited warranty ................................. 88
10.3.3 Cab paint warranty........................................................ 88
10.3.4 Cab structural warranty ................................................. 89
10.3.5 Front and rear axle warranty ......................................... 90
10.3.6 Chassis frame warranty ................................................ 90
10.3.7 Cummins engine warranty ............................................ 91
10.3.8 Allison transmission warranty........................................ 96

5
1 Legal notice
1.1 Copyright
All rights to this manual and their attachments are reserved by Rosenbauer
America and Rosenbauer Motors, hereinafter referred to as Rosenbauer.

This document is for the personal use of the recipient only. No part of this
document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording, or by any
information storage or retrieval system, or translation into other languages, except
as expressly permitted in writing by the publisher.

Information out of this manual may not be passed or made accessible to third
persons, especially competitors.

1.2 Manufacturer and after sales address

Rosenbauer Motors, LLC
5181 260th Street
P.O. Box 549
Wyoming, MN 55092, United States of America

Telephone number: 651-462-1000

Fax number: 651-462-1700
E-Mail: info@rosenbaueramerica.com
Internet: www.rosenbaueramerica.com

Rosenbauer Emergency Customer Service Technical Support

Telephone number: 877-543-5591

Please have your vehicle identification number (VIN) ready when requesting
information or assistance; this will allow us to assist you more quickly.

6
2 Introduction
2.1 Welcome note
Rosenbauer would like to thank you for your recent Commander purchase. We
are confident that when properly operated, maintained and serviced your
Rosenbauer fire apparatus will provide you with many years of reliable service.

Please fill out and return the Rosenbauer America Warranty Registration Form as
soon as possible. This form can be found in the front pocket of this binder.

Please read this manual carefully before starting operation. Obey all instructions.

Some of the information compiled in this manual was derived using manufacture’s
literature of purchased products. Rosenbauer does not claim any copyright
privileges to this material nor does it guarantee the accuracy of this information. In
addition to this manual also observe suppliers manuals (e.g. operation and service
manuals for the generator, rescue equipment and firefighting equipment).

Only personnel familiar with this manual and equivalent qualified personnel may
operate or service this product.

Keep this and other manuals with the apparatus. Keep for future use.

2.2 Liability and injury

Due to the information given within this manual, Rosenbauer strictly is not liable for
any direct damage or consequential damages which are caused by improper use
or service as well as caused by unauthorized modification of this product or in this
manual.

Only personnel familiar with this manual, the vehicle inclusive equipment,
according operation, local laws, local safety regulations and accident prevention
may operate this product.

Rosenbauer is not liable for any injury or damage caused by personnel who are
unfamiliar with the operational procedures described in this manual, failing to
comply with the operation manual and/or failing to comply with regulations,
subsequent procedures, safety and accident prevention.

If this manual shows technical failure or typing error, Rosenbauer reserves the right
to make modifications anytime and without previous announcement.

This manual can include description and graphics, which are not mounted on the
delivered product.

From data, graphics and description within this manual, no demands on

modification to already delivered products could be made.

7
 For your own safety, use only spare parts and accessories from Rosenbauer. Use
of other products may result in injury, Rosenbauer assumes no liability!

Check the delivery immediately after arrival for completeness and transport
damages.

 Defects, damages and loss of parts must be immediately submitted in

written form.
 Take photos of damaged parts.
 Report the fault in written form to the manufacturer. Please refer to
"Manufacturer and After Sales Service Address".

2.3 Vehicle identification

Every Rosenbauer Commander has a unique vehicle identification number (VIN).
The VIN is located near the bottom of the identification plate. The identification
plate is located on the driver’s side door sill. Identifying the VIN is important when
referring to the manufacturer in regards to parts and technical issues.

My VIN: 54F2CB51XEWM10809

8
2.4 Use of the operation manual
2.4.1 Validation

This manual provides information needed to operate the product.

This manual contains descriptions of special equipment as well as some

abstractions and exemplary illustrations. The actual equipment of the product may
therefore differ in part from the descriptions and illustrations.

2.4.2 Signs and symbols

Highlighted Text

To simplify legibility and clarity, various pieces of information are marked with
symbols.

These symbols indicate the following:

► Perform action in the hierarchy to be maintained as described.
 Reactions to the actions performed (results).
● Lists.
 Further Information about this topic.

Notes for additional information to operate the unit.

Read/obey additional information in the manufacturer documentation.

Figures

Where necessary, the text is illustrated with drawings. A caption is provided below
the illustration. The reference from the text to a position within the illustration is
given by inserted figures (e.g. S1).

9
 Warning notices

Safety information alerts the user of hazards and informs the user how to be aware
of the hazards.

Safety information is written at the beginning of each chapter, before any

instructions to perform an action which assumes a hazardous situation. Further
safety information is located at the beginning of this manual.

Safety instructions that must be observed are highlighted within this manual as
follows:

DANGER!
This sign indicates an extremely hazardous situation which, if not avoided, will
result in death or serious injury.

WARNING!
This sign indicates a hazardous situation which, if not avoided, could result in death
or serious injury.

CAUTION!
This sign indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.

NOTICE
This sign is used to address practices not related to personal injury.

Additionally the information in the operation manual within the chapter “Technical
data” and the safety information within the delivered supplier’s manuals should be
observed.

10
3 Safety
3.1 Proper usage
Incorrect use of the product (vehicle, portable pump, etc.) may cause personal
injury. In addition, the product or other property may be damaged.

Rosenbauer can only guarantee safety, reliability and performance of the product,
if it is used as described in this manual.

Any unauthorized changes, modification or incorrect operation may affect the

intended use and cause personal injury or property damage.

In the driver’s cabin and crew cabin of fire fighting vehicles, there is a maximum
passenger capacity, this rule must be obeyed.

 Please refer to the operation manual chapter “Technical data”.

The firefighting products may only be used in proper technical condition and by
qualified staff for the following purpose:

 to fight fires using water (for firefighting)

 to rescue people from emergency situations
 to provide technical assistance

Modifications, changes and repairs may only be completed by persons authorized

by the manufacturer. Unauthorized modifications, changes or improper usage will
render all liability of the manufacturer void for any resultant damage.

3.2 Markings and warning signs

Safe use is only possible if all necessary information for safe operation is
observed. This information includes obeying all safety and warning instructions.

In addition to the instructions in this operating manual, read and observe all the
safety and warning signs affixed to the product.

► Replace missing or damaged signs.

► Keep the safety and warning signs clean and legible.

3.3 Other regulations

In addition to this operating manual observe and comply with relevant version of
general laws, directives and regulations (e.g. protective clothing, road traffic act,
national training regulations for the fire service, accident prevention regulations,
fire service regulations, industrial medicine and environmental safety rules, state
law for fire and disaster protection, etc.).

11
3.4 Training and qualifications
Improper operation due to a lack of qualification can cause serious accidents and
failure in success of the task. Safe use is only possible if the product is operated
and maintained exclusively by specially trained personnel.

Only ongoing practice and training by experienced firefighting personnel will

ensure safe use. The various operation procedures must be practiced at regular
intervals.

The vehicle driver must hold a valid current driver’s license for the appropriate
vehicle class.

Before use, the personnel must be made familiar with use of the product.

The operator is responsible for defining authorities, responsibility and for

supervising the personnel as well as for providing adequate training and practice in
compliance with all current regulations.

Even during operation, ensure that persons without specialist skills are never
allowed to operate the product.

The personnel must have the physical and the mental aptitude necessary to
operate the product. Minors and persons with no firefighting training must not
operate the product.

Modification and changes of the product, firefighting vehicle and built-in equipment
may be carried out only with written permission of Rosenbauer and by the
manufacturer’s authorized person.

3.5 General safety instructions

The following instructions provide an overview on the use of the product safely.
This general overview is supplemented by the safety instructions in the detailed
descriptions of the various sections.

Always remember the possibility of danger when operating machines. Always use
the prescribed personal protective equipment.

The condition of the product must meet the local safety regulations and the local
firefighting regulations. Ensure that the product is ready for action at all times.

In case of contact with dangerous chemicals, such as dry powder, obey material
safety data sheet and information given by the manufacturer.

Pay attention to the operation and service manual from additional components.

If problems cannot be solved or if repairs cannot be carried out by specially trained

personnel, contact Rosenbauer immediately.

12
3.6 List of conventional signs
3.6.1 Warning signs

This warning sign indicates danger of electric shock hazard.

This warning sign indicates fire hazards.

This warning sign indicates explosion hazards.

This warning sign indicates danger of oxidizing materials.

This warning sign indicates danger of harmful or irritant materials.

This warning sign indicates danger of corrosion.

This warning sign indicates danger of hearing damage.

This warning sign indicates danger of inhalation hazard.

This warning sign indicates danger of hot liquids and steams.

This warning sign indicates danger of hot surfaces.

This warning sign indicates danger of crushing.

This warning sign indicates danger of falling objects.

13
 This warning sign indicates danger of high pressure.

This warning sign indicates danger of high vacuum.

This warning sign indicates danger of overhead loads.

This warning sign indicates a hazardous to environment.

This warning sign indicates a risk of falling.

This warning sign indicates danger of shearing.

This warning sign indicates danger of impact.

This warning sign indicates danger of local stability loss.

This warning sign indicates danger of slipping on sloped surfaces

due to reduced friction.

This warning sign indicates danger of laser radiation.

This warning sign indicates danger of stumbling.

This warning sign indicates danger of hand injury.

14
3.6.2 Prohibition signs

Do not smoke!

Do not handle with open flames!

Do not step here!

No climbing for unauthorized personnel!

Do not extinguish with water!

Do not spray water!

Do not linger under the rescue platform!

Do not touch or grip inside!

Do not linger in the danger zone!

No access for unauthorized personnel!

15
3.6.3 Mandatory safety signs

Wear ear protection.

Wear goggles or protective face shield.

Wear goggles and ear protection.

Wear safety helmet.

Wear safety gloves.

Wear safety boots.

Wear full body protection.

Wear seat belts.

Wear self-contained breathing apparatus.

Hold handrail.

Keep sufficient distance. Special attention.

Emergency operation.

Take care of environmental protection.

16
3.7 Warning notes

DANGER!
Danger of fatal or severe injury to the crew or pedestrians due to moving
the vehicle or its components during service operations/maintenance and
repair work.
Prior to service and repair works:

 Stop the engine with parking brake applied.

 Turn off the ignition switch.
 Chock the wheels of the vehicle with the attached wheel chocks before
maintenance and repair work.
 Place a “Do not start” note over the steering wheel, or isolate the electrical
system from the batteries (turn off the master power disconnect switch).

Loss of stability can lead to rolling over of the vehicle, causing

personal injuries and damage to property.

 Test the stability before starting operation.

 Follow the instructions regarding setup (ground surface, max. inclination, wind
force) in the operation manual.
 If a loss of stability seems imminent, immediately stop all work and restore
stability.

Danger of fatal or severe injury due to failure to observe safety

measures!
Persons who fail to fasten their seat belts can be thrown against hard surfaces
in case of traffic accident or abrupt vehicle maneuvers.

 Before starting to drive, all persons must fasten their seat belts.

Danger of fatal or severe injury due to unintentional vehicle movements!

Unintentional vehicle movements can cause fatal injury to the crew or
pedestrians. Before leaving the cabin, the driver must:

 Park the vehicle on a safe surface.

 Select transmission to Neutral.
 Apply the parking brake.
 Chock the wheels of the vehicle with the attached wheel chocks before
maintenance and repair work.

17
 Danger of fatal injury or health hazard due to inhalation of toxic exhaust
fumes!
Combustion engines working in enclosed areas build toxic exhaust fumes. Is there
the need of working in enclosed areas, obey following:

 Extract the exhaust fumes outside using exhaust hoses.

 Make sure for adequate ventilation.

WARNING!
Danger of fatal or severe injury due to improper use of the braking system!
Repeated braking, cadence braking, a leak in the compressed air system, or the
use of the parking brake while driving, reduces the operating pressure; this in turn
could result in locking of wheels and can cause severe accidents.
 Ensure correct compressed air system and braking system operations.
 Do not start driving if the compressed air pressure in the braking system is too
low.
 If the warning lights of the brakes or the compressed air system comes on, stop
the vehicle immediately and do not start it up again.
 Avoid repeatedly depressing and releasing the brake pedal.
 Never use the parking brake as a driving brake while driving.
 Report malfunctions to your work shop personnel as quickly as possible and
make sure that the repair is performed.

Injury to persons and damage to property due to vehicle components not

being in transport position.
Vehicle components that are not in transport position can impair the vehicle’s
maneuverability and cause serious accidents.
 If the pilot lamp lights illuminate while driving, stop the vehicle immediately
and identify the cause before driving on.

Personal injuries and damage to property can occur due to a restricted view
of movable machine parts.

 Do not linger in the danger zone.

 Follow the training and operation manual.

Failure to wear proper protective gear could result in death or serious

injury.

 Wear protective gear.

18
Danger of falling!
Lingering on the roof during fire-fighting operations or vehicle movement could
result in death or serious injury.
 Do not linger in the danger zone.
 Lingering on the roof is permitted only for manually operation of the roof
turret or during the removal of equipment on the roof.
 The operator must secure himself with a safety line on the roof and/or put up
the safety railing.
 Operate the roof turret with closed roof hatch only.
 Before extending the light mast make sure that there are no persons in the
moving range of the light mast.

Potentially fatal injuries due to the engine taking in flammable gases!

 Do not operate the engine in areas with a heavy concentration of

flammable vapors such as e. g. diesel, gas or propane.
 When handling flammable liquids and gases, always shut off the engine
immediately.

Potentially fatal injuries and danger of explosion!

 Do not operate the generator in areas with a heavy concentration of

flammable vapors such as e. g. diesel, gas or propane.
 When handling flammable liquids and gases, always shut off the
generator immediately.
 Do not operate the generator in closed rooms.

Danger of fatal or severe injury due to incorrect use of the parking brake!
The use of the parking brake as a driving brake while driving, can block the
vehicle’s wheels and cause severe accidents.
 Never use the parking brake as a driving brake.

Danger of injury due to loose items in the cab.

Loose items in the cab can roll underneath the brake pedal and prevent braking,
or damage the windscreen when tipping the cab.
 Do not leave tools or other objects in the cab.
 Secure loose objects with destined fixtures.

19
 Danger of fatal or severe injury due to rolling over of the vehicle.
Almost all fire fighting vehicles have systematical high points of gravity;
additionally, they are typically loaded to a point just below their permissible total
weight. Incorrect driving (even in emergency response situations) can lead to
rolling over of the vehicle.
 Perform all steering movements carefully when traveling at high speeds.
 When driving on dirt tracks or off-road, drive slowly and extremely
cautiously.
 Avoid driving over obstacles at high speed.
 If the vehicle threatens to tip on a slope, steer in downhill direction
immediately to improve the vehicle’s stability.

Danger of fatal or serious injury!

Breathing apparatus fixtures and harnesses in the cabin do not replace the
standard installed safety seat belts.
 While driving the vehicle, the breathing apparatus must be in storage.
 Only when vehicle is stationary, open the breathing apparatus fixture and
remove the breathing apparatus.
 During yearly inspection of the vehicle and especially after each use, check
breathing apparatus fixtures for proper function.
 Always use your seat belts.

Danger of crushing and sheering of limbs due to moving or rotating parts!

 Do not reach into or grasp moving or rotating parts.
 Observe a safety distance to the danger zone.
 Use protective equipment.

Danger of explosion due to flammable fuel!

 During work on the fuel system, fuel can ignite and cause potentially fatal
injuries.
 Do not smoke.
 Keep fuel away from open flame.
 When handling fuel, always keep a fire extinguisher at hand.

Danger of serious injury and accidents!

A tire blowout can cause the vehicle handling to be impaired.

 Be sure to know the top speed rating of your vehicle.

 Please refer to the chapter “Chassis specifications”.
 In the case of a tire blowout, keep a firm hold on the steering wheel and slow
the vehicle to a stop.

20
Danger of serious injury and damage due to explosion, fire and
chemical burns!
When charging vehicle batteries, a highly explosive electrolytic gas mixture
(hydrogen and oxygen) is released; it is easily flammable and may release highly
acidic battery acid.
 Wear safety goggles whenever servicing a battery.
 Follow safety instructions on the outside of the battery.
 Do not smoke.
 Avoid fire, open flame and sparks.
 Avoid sparks when handling cables and electrical devices, and through
electrostatic discharge.
 Do not connect the minus pole of the battery jumper cable near to the
discharged battery (generates sparks).
 Always remove negative battery ground cables first and install them last to
avoid sparks.
 The vehicles must not touch (sparks will occur on connecting the positive
poles).
 Never short-circuit the battery.
 Ventilate batteries thoroughly before any external start.
 When connecting the connecting lead, do not bend over the battery.
 Avoid skin and eye contact with any battery acid that escapes.
 Keep unauthorized persons clear of the battery.
 Ensure that the battery voltage matches.
 Never disconnect the batteries while the engine is running.

Danger of fatal or severe injury due to falling down from an exposed

location!

 Use safety/protection equipment.

 Be careful when climbing up or down the ladder.
 Use the ladder rungs and hand rails as intended.
 Be extremely cautious on uneven and slippery surfaces.
 Observe a safety distance to the roof edge.
 Obey the labels with safety procedures attached to the vehicle and its
equipment.

Danger of fatal or serious injury from electrical shock!

Danger of electrical shock during a thunderstorm. People who are on or near the
vehicle during a lightning strike could be seriously injured.
 Lingering on the roof during a thunderstorm is prohibited.
 The usage of the light mast during a thunderstorm is prohibited.
 The usage of the ladder lowering device during a thunderstorm is
prohibited.
 The usage of the turret during a thunderstorm is prohibited.

21
 Danger of fatal or serious injury from electrical shock!
Water, firefighting foam and metallic materials conduct electricity.
 Do not aim turret or nozzle (extinguishing agent jet) toward high voltage
power lines or other high voltage electrical circuits.
 Keep a safe distance to energized components under all circumstances.
 Do not use foam compound while firefighting in electrical installations.
 Do not park vehicles underneath or near overhead power lines, should use
caution.
 Vehicles with roof structures as e.g. extendable light tower or turrets.
 Do not load, unload or use metal ladders in areas where contact may be made
with overhead power lines or high voltage electric circuits.

Safety clearance of materials conducting electricity to overhead lines

Voltage Safety clearance

220 kV - 380 kV 16 ft (5 m)
110 kV - 220 kV 13 ft (4 m)
1 kV - 110 kV 9 ft (3 m)
up to 1 kV 3 ft (1 m)

Safety clearance with portable fire extinguisher, when extinguishing at low-

voltage installations

Voltage Kind of extinguishing Safety clearance

up to 1 kV Dry chemical powder (ABC, BC), CO2 and halon 3 ft (1 m)
Water fire extinguisher, wall hydrant 9 ft (3 m)

22
 CAUTION!
Danger of injury for the operator due to performing action in wrong order!
 Individual operating instructions must be done in the prescribed order.

Danger of hearing damage due to extended presence in the vicinity of the

running pump!
 Use hearing protection.
 Do not linger in the danger zone.

Danger of burns due to touching the hot engine and engine

components!
 Do not linger in the danger zone.
 Do not touch hot parts of the engine.
 Do not touch any parts of the exhaust system.
 Wait until all parts have cooled down.

Danger of burns due to hot coolant system!

 After shut-down, do not start maintenance work until the coolant system has
cooled down.

Danger of injury to persons or damage to the vehicle due to failure to

perform a visual check!
Perform the visual checks before driving to make sure that:
 Roof turret is in transport position.
 Light mast is retracted.
 Moveable rapid intervention equipment is locked
 Ladder is locked.
 Equipment is stowed correctly.
 Tires and tire pressures are normal.
 All roller shutters are locked.
 All shorelines (power, compressed air) are disconnected.
 All doors and folding steps are closed.
 Indicator lights in the driver’s display have been checked.

Danger of injury due to burns!

A short circuit releases powerful currents that can considerably heat up and even
melt metals.
 Use only jump start cables in line with ISO 6722 and NATO connector.
 In case of jump start cables with crocodile clips, ensure correct polarity.
 Never short-circuit battery poles or the jump start cable.
 Avoid unintended connecting of the positive pole and electrically conductive
vehicle parts by tools, watches, jewelry etc.
 Do not connect the jump-start cable to fuel, hydraulics or brake lines.

23
 Danger of crushing or material damage due to moving parts!
Moving components that have not latched into position, or are not at their limit
positions, can cause injury to persons or material damage.
 Only hold compartment doors and steps at suitable points.
 Before opening swing-out shelves and swivel reels, fully open the roller
shutters in question.
 Observe spring and inertia effects when opening and closing compartment
doors and the rear step.
 Pay attention while closing the seat box cover.

Environmental and health hazard due to lubrication oils!

Lubrication, transmission and hydraulic oils can cause permanent water
pollution and endanger fauna and flora of all types.
 Avoid skin contact with hazardous oils.
 Avoid ground contact with lubrication oils.
 Collect used oils sorted by type and recycle.
 Observe local oil disposal regulations.

Danger of burning!

 Do not grip onto switched-on or recently switched-off search lights.

Danger of crushing!
Danger of crushing due to pneumatic cylinders and drives.

 Do not grasp moving parts.

 Do not reach into the danger zone.

24
 NOTICE
Damage to the vehicle and equipment due to failure to observe visible or
audible warning signals!
 Monitor all visible and audible warning signals, measured value displays and
warning lights.
 Observe training and operating instructions.

Damage to property due to departure of the vehicle with a supply line

attached!
To ensure readiness for operations, the pneumatic and electrical system can be
energized by a supply line from the parking bay. Driving the vehicle out of the bay
with the supply line attached can cause damage to the supply line and the
receptacle.
 Manually disconnect the supply line before departure.
 When using types with an automatic disconnection function at the vehicle
parking bay, use a self-retracting supply line.

Vehicle failure due to discharged batteries!

The vehicle battery discharges in case of continual use or while the engine is not
running with the ignition on or off.
 Check the battery charge state regularly (every three months).
 Charge or replace the battery if the charge state is low.
 When the engine is shut down, switch off the ignition.
 Disconnect the vehicle’s power supply in case of an extended period of disuse
(main battery switch off).

Damage to electronic assemblies due to actuating the battery main switch!

The battery is an important part of the vehicle’s electrical circuit even when the
engine is running. If the vehicle power supply is interrupted at the battery main
switch while the engine is running, power peaks can occur, this can destroy the
electronic equipment of the chassis and superstructure.
 Only deactivate the battery main switch while the engine is shut off.

Damage to electronic components due to external charging!

An external, not electronic controlled battery charger can destroy electronic
assemblies in the vehicle during external charging.
 To ensure the operational readiness of the vehicle, the battery must be isolated
from the vehicle’s electrical circuit (battery switch off) before connecting the
battery charger. Disable battery main switch.

25
3.8 Safety labels
Locate, read, and understand all warning labels on the apparatus and identify the
hazard that each label describes. If a label comes off or becomes hard to read,
contact Rosenbauer for a replacement.

26
3.9 Reporting safety defects
If you believe that your vehicle has a defect which could cause a crash or could
cause injury or death, you should immediately inform the National Highway Traffic
Safety Administration (NHTSA) in addition to notifying Rosenbauer Motors, LLC.

If NHTSA receives similar complaints, it may open an investigation, and if it finds

that a safety defect exists in a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Rosenbauer Motors, LLC.

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–
327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov ; or write to:

Administrator, NHTSA
400 Seventh Street, SW.
Washington, DC 20590

You can also obtain other information about motor vehicle safety from
http://www.safercar.gov.

3.10 Material safety data sheets (MSDS)

Material Safety Data Sheet information can be found on the reference CD supplied
with this apparatus.

3.11 Seatbelts
DANGER!
Danger of fatal or severe injury due to failure to observe safety measures!

Persons who fail to fasten their seat belts can be thrown against hard surfaces in
traffic accidents or abrupt vehicle maneuvers.

 All occupants must wear seatbelts when operating or riding in the vehicle.
 Seatbelts must be inspected regularly to ensure they remain in proper
condition.

This apparatus uses a three point seat belt system. Occupants should always
fasten seatbelts before driving. Fasten the three point seat belt by pushing the
latch into the buckle until and audible click is heard. To ensure the belt is latched,
give the seat belt a slight tug. The shoulder strap should be positioned diagonally
across your chest, as shown in the illustration. Release the seat belt by pressing
the release button.

27
3.12 Three points of contact rule
Always use the “3-Points of Contact Rule” when entering or exiting the apparatus.

Always keep three points of contact with the ground or the equipment until you are
stable on the equipment or on the ground. This means that before you lift one of
your legs to climb up on the equipment, you must have both hands firmly grasping
the equipment to help pull yourself up; before you let go of one of the hand holds
when dismounting, you need to make sure that both feet are firmly planted on the
ground.

Additional safety rules for getting on or off equipment or climbing in the cab of a
truck:

 Only climb on or get off when the equipment or vehicle is stationary.

 Always mount or climb down while facing the truck or the equipment.
 Only use points of contact that were intended to be used to climb on or
dismount.

3.13 Do not move apparatus light

CAUTION!
Do Not Move Apparatus if the open door warning light is flashing. If
flashing, verify that all doors and compartments are closed, and that all
equipment is secured.

The “Do Not Move Apparatus” (door ajar) light is located on the center section of
the roof of the cab. This light will blink if a cab or compartment door is open and
the parking brake is not engaged.

If the “Do Not Move Apparatus” warning comes on while driving, stop the vehicle
and secure the open door, open component or loose equipment.

3.14 Vehicle data recorder

Your vehicle is equipped with a Vehicle Data Recorder (VDR) System. The VDR
records the following information:

 Engine RPM
 Engine throttle percentage
 Vehicle speed
 ABS events
 Transmission range information
 Parking brake position
 Master warning switch position
 Seat occupied status
 Seatbelt status

28
4 Product description
4.1 Vehicle side views

A B C

D E F G H

A) Rear View Mirror F) Diesel Fuel Cooler

B) A/C Condenser Unit G) Air Tank
C) Grab Handles H) Diesel Fuel Tank
D) Cab Side Marker Light I) Engine Exhaust Outlet
E) Door Handles

C B A

H I E D

29
4.1 Vehicle front view
A

B B

C
D

E E

F F

G
G

A) Emergency Light Bar

B) Rear View Mirrors
C) Cab Clearance Lights
D) Windshield Wipers
E) Headlights
F) Side Marker Lights
G) Turn Signals

30
4.2 Driver’s panel view

Please refer to individual

switch descriptions in
section 5 for more info.

4.3 Driver’s kick panel view

A
B C D E

A) Engine and Transmission ECM Communications Port

B) DEF Regeneration Inhibit Switch
C) DEF Regeneration Switch
D) V-Mux Communications Port
E) Vehicle Data Recorder Port

31
5 Technical description
5.1 Master power disconnect switch

CAUTION!
Damage to the alternator may result!

 Do not turn off the master power disconnect switch while the engine is running.

The master power disconnect switch is used to disconnect electrical power to the
vehicle while the vehicle is not in use.

The master power disconnect switch is located on the front of the driver’s kick
plate. This switch must be turned on in order to operate the apparatus.

32
5.2 Parking brake

WARNING!
Danger of injury and equipment damage!
 When parking on a grade, always chock wheels and turn the front wheels
completely in the direction of the curb.
 The parking brake is only intended to hold the vehicle in a parked position.
 The parking brake may be used to assist the apparatus to a stop, but only in
an emergency.
 The parking brake should not be used to stop the apparatus during normal
driving.

The parking brake is applied by operation of the yellow parking brake valve shown.
 To apply the parking brake, PULL the parking brake valve.
 To release the parking brake, PUSH the parking brake valve.

While the master and ignition switches are on, an indicator lamp in the driver’s
display panel will illuminate when the parking brake is engaged.

SETTING THE PARKING BRAKE WILL AUTOMATICALLY PLACE THE

TRANSMISSION IN NEUTRAL. The transmission selector must be put into
neutral (by the driver) after this safety over ride has taken effect in order for system
become fully functional.

33
5.3 Brake and throttle pedals

WARNING!
Danger of injury and equipment damage!

 Excessive use of the service brakes may result in overheating and brake fade
which will decrease stopping ability.

The service brake pedal is located on the driver side floorboard of the apparatus.
The service brake pedal is positioned on the left.

The throttle (accelerator) pedal is located on the driver side floorboard of the
apparatus. The throttle pedal is positioned on the right.

Service brake pedal

Engine throttle pedal

34
5.4 Steering column controls
5.4.1 Multifunction lever
The multifunction lever is located on the left side of the steering column below the
wheel. It operates the turn signals and headlight dimmer:

 Push the lever towards the dash to activate the right turn signal.
 Pull the lever towards the seat to activate the left turn signal.
 To turn the high beams on or off raise this lever until it clicks.

NOTE: Dashboard indicator lights will correspond to the function you have
selected.

5.4.2 Tilting / telescoping lever

The tilting/telescoping lever allows you to adjust the steering wheel position for
maximum comfort and control of the vehicle:

 Push lever down to adjust height of the steering wheel.

 Pull lever up to change the angle of the steering wheel.

NOTE: When you are finished driving, the steering wheel should be tilted forward
and retracted inward for ease of exit and entry.

5.4.3 Hazard light switch

The hazard light switch is located on the steering column; it activates the four way
hazard flashers.

 To activate, pull the switch outward from the steering column.

 To deactivate, push switch inward toward the steering column.

NOTE: The master power disconnect switch must be in the on position to operate
the four way hazard flashers.

35
5.5 Dash gauges and tell-tales

A) Primary Air Pressure W) Engine Coolant Temperature

B) Warning Light (Primary Air Pressure Low) X) DEF Fluid Level
C) Upper Left Hand Button Y) Voltage Meter
D) Lower Left Hand Button Z) Warning Light (Voltage)
E) Multifunction Display 1) Water In Fuel Indicator
F) Lower Right Hand Button 2) Automatic Traction Control
G) Secondary Air Pressure 3) Engine Pre-Heater (Wait to Start)
H) Warning Light (Secondary Air Pressure Low) 4) Battery Power Indicator
I) Upper Right Hand Button 5) Park Brake Engaged Indicator
J) Stop Engine Indicator Light 6) High Exhaust System Temperature
K) MPH Mode Indicator Light 7) Air Intake Restriction Indicator
L) Speedometer 8) Left Turn Arrow Indicator
M) Engine Revolutions Per Minute (RPM) 9) Anti-Lock Brake System Malfunction
N) Check Message Indicator 10) High Transmission Temp Indicator
O) Malfunction Indicator 11) Check Transmission Indicator
P) Check Engine Indicator 12) High Beam Headlight Indicator
Q) Km/h Mode Indicator 13) Airbag Malfunction Indicator
R) Fuel Level 14) Low Engine Coolant Level Indicator
S) Warning Light (Low Fuel) 15) Re-gen Inhibit Switch Engaged
T) Oil Pressure 16) Particle Filter Regeneration
U) Oil Pressure Warning Light 17) Right Turn Arrow Indicator
V) Engine Coolant Temperature Warning Light

Display functions will be controlled by 4 switches (C,D,F and I). In normal mode,
the switch on the left side will control selection of heading for the corresponding
line. The switch on the right side will control selection of parameter for the
corresponding line. Pressing and holding the switch for 1 second will restore the
previous line item. For full screen items, the switch functions will be displayed.

36
The multifunction display menu will include the following headings
illustrated as they would appear on the display. Activation of the top
left button will move to the next available heading selection.
Activation of the top right hand button will select and scroll through
the available options under that particular heading.

Under the VEHICLE heading, the following parameters will be

displayed. Please note that parameters will not be displayed when
no data is available.
-Transmission Oil Temp -Total Vehicle Distance
-Battery Potential -Engine Hours
-Vehicle Speed -Engine Speed
-Fuel Level -DEF Catalyst Tank Level
-Engine Oil Pressure -Battery Current
-Engine Coolant Temp -Brake Primary Air Pressure
-Engine Oil Temp -Average Fuel Economy
-Brake Secondary Air Pressure
-Engine Intake Manifold Pressure
-Aftertreatment Exhaust Gas Temp
-Engine Percent Load At Current Speed
-Actual Engine Percent Torque
-Instantaneous Fuel Economy

Under the TRIP heading, the following parameters will be displayed.

-Total Fuel Used -Total Idle Fuel Used
Trips 2 and 3 will display the same information as illustrated for trip
1. Trip Distance is reset by pressing and holding the upper right
hand button (F) for a period of 2 seconds while trip mileage is
displayed.

Under the SETTINGS heading, the following parameters will be

displayed. Pressing and holding the right hand button will execute
the function
-Select Units -Select Contrast

An asterisk will appear next to the “DIAGNOSTICS” heading if

active diagnostic codes are present.

37
5.6 Transmission controls

WARNING!
Danger of severe injury due to unintentional vehicle movements!

 If you leave the vehicle and the engine is running, the vehicle can move
unexpectedly and you or others could be injured. If you must leave the engine
running, do not leave the vehicle until you have completed all of the following
procedures:
1. Put the transmission in N (Neutral).
2. Be sure the engine is at low idle (500-800 rpm).
3. Apply the parking brakes and emergency brake and make
sure they are properly engaged.
4. Chock the wheels and take any other steps necessary to keep
the vehicle from moving.

The pushbutton shift selector has the following components:

 R (Reverse)—Press this button to select Reverse

 N (Neutral)—Press this button to select Neutral
 D (Drive)—Press this button to select Drive. The highest forward range
available will appear in the digital display window. The transmission will start
out in the lowest available forward range and advance automatically to the
highest range.
 ↑ (Up) Arrow—Press the ↑ (Up) Arrow when in D (Drive) to request the next
higher range. Continually pressing the ↑ (Up) Arrow will request the highest
range available.
 ↓ (Down) Arrow—Press the ↓ (Down) Arrow when in D (Drive) to request the
next lower range. Continually pressing the ↓ (Down) Arrow will request the
lowest range available.

All drivers should read the ALLISON operators manual to familiarize themselves
with the features of this transmission.

38
5.7 Heating ventilation and air conditioning (HVAC) controls
5.7.1 Front HVAC controls

The HVAC controls are accessed through the V-Mux control panel. These
controls allow you to adjust the heating, ventilating, defrosting, and air conditioning
functions. The V-Mux HVAC control panel is shown below.

To access the HVAC control panel, push the button under the “HVAC” heading
(A).

To select heat or air conditioning, press the button located beside the “Heat / A/C”
box (B).

To adjust the fan speed, press the button beside the “Fan Speed” box (C). Fan
speed selection consists of OFF, LOW, MEDIUM, OR HIGH.

To select defrost or vent settings, press the button beside the “Defrost / Vent” box
(D). The vent settings consist of defrost, vent, and off.

To adjust the temperature, use the buttons beside both the “Temp UP” and “Temp
Down” boxes (E and F). The temperature setting is displayed in the center of the
V-Mux screen.

5.7.2 Rear HVAC controls

A B

The rear HVAC controls are located on the roof mounted HVAC unit. Knob A
adjusts the fan speed. To increase airflow, turn knob A clockwise. To shut the
rear HVAC off, turn knob A to the “OFF” position. Knob B controls the air
temperature of the rear HVAC unit.

39
5.8 Ignition switch
The ignition switch activates the main electrical systems of the vehicle. It provides
power to the ignition system components and to some accessories. The master
power disconnect switch must be on to operate the ignition switch.

5.9 Engine start switch

The engine start switch activates the starter motor which starts the engine. The
master power disconnect switch and ignition switch must be on in order to operate
the engine start switch.

5.10 Dash panel dimmer control

The dash panel dimmer control allows the driver to set the amount of light being
emitted from the dash gauges. The brightness is adjusted by moving the slide on
the dash panel dimmer control switch up for brighter dash lights or down for
dimmer dash lights.

5.11 Regeneration “regen” switch

The manual regeneration or regen switch initiates the DPF regeneration process if
the vehicle is stationary and the regeneration inhibit switch is not active. For more
information on this switch, please refer to the emission control system section of
this manual.

5.12 Regeneration inhibit switch

The regeneration inhibit switch, when in the on position, will stop an active
regeneration or prevent an active regeneration from starting. For more information
on this switch, please refer to the emission control system section of this manual.

5.13 Headlight and parking light controls

Parking lights are activated by toggling the headlight switch to the middle position.
Headlights are activated by toggling the headlight switch past the middle position,
to the fully on position. The rear taillights will also illuminate when the headlight
switch is in the middle or fully on position. See “Multifunction Lever” section for
information on switching between high and low beams.

40
5.14 Windshield wiper controls
To start or stop the windshield wipers, push the “ON/OFF” button on the
windshield wiper switch. To adjust the speed of the windshield wipers, toggle the
“ON/OFF” button upwards for faster wipe speed or downwards for a slower wipe
speed. To initiate the windshield wash function, push and hold the “WASH” button
until the windshield is clean.

5.15 Window controls

The windows of the apparatus can be raised or lowered using the mechanical
hand crank located on the door panel of each door. Operate the hand crank to
raise or lower each window.

5.16 Door lock controls

The door locks are operated by turning the red knob on the interior cab door
handle. Turn the red knob downward to lock the door. Reverse this action to
unlock the door. Each door must be locked or unlocked separately.

5.17 Engine brake controls

Engine braking is controlled using the V-Mux control panel. To activate or adjust
the intensity of engine braking, press the button on the V-Mux control panel that
corresponds with the “Engine Brake” title block. The engine brake title block is
normally located on the home screen but it may be located on a different menu
depending on your application.

There are four levels of engine brake intensity:

 Off
 Low intensity
 Medium intensity
 High intensity

41
5.18 Engine high idle control
The engine high idle control switch forces the engine to idle at an increased RPM.
Elevating the engine RPM will increase engine temperature, exhaust temperature,
and alternator charging ability.

To activate the high idle function, place the transmission in neutral (N), apply the
parking brake, and press the button on the V-Mux display that corresponds with
the “High Idle” title block.

To deactivate the high idle function, press the button on the V-Mux display that
corresponds with the “High Idle” title block. Please note that releasing the parking
brake or placing the vehicle in gear will also deactivate high idle.

The engine idle RPM will automatically increase if the vehicle senses low battery
voltage.

5.19 Master warning control

The master warning control switch provides power to the warning lights on the
apparatus.

To activate the master warning control, press the red button on the V-Mux display
labeled “E-Master”.

To deactivate the master warning control, press the red button on the V-Mux
display labeled “E-Master”.

Please note: any white warning lights will deactivate automatically when the
parking brake is set per NFPA 1901.

42
5.20 Power mirror controls
CAUTION!
Danger of injury or equipment damage!

 Always check mirrors to assure mounting hardware is secure. Drivers must

always adjust mirrors to maximize visibility and to limit blind spots.
 Beware of blind spots (areas of obstructed view). Use a helper to walk around
the vehicle to aid in identifying blind spots. This will help familiarize the driver
with the vehicle’s blind spots allowing for him/her to compensate for this lack of
vision while driving, making turns, or changing lanes.

Mirror heat is activated by using the V-Mux control panel. Please refer to the V-
Mux controls section of this manual for more information.

Mirror adjustment is achieved by using the power mirror adjustment knob. This
knob must be turned clockwise or counterclockwise to select the mirror that needs
adjustment. The left position selects the driver’s side mirror, whereas the right
position selects the officer’s side mirror. The middle position is the off position. In
the middle position, no adjustments to the mirrors can be made. Once a mirror is
selected, the power mirror adjustment knob can be “rocked” in the given direction
you wish the mirror to move. The mirror will move in the direction the knob is
rocked.

If more than one power mirror adjustment knob is present your apparatus has a
two-piece rear view mirror. In this case, the top and bottom mirrors are adjusted
independently. The top and bottom mirror sections are controlled by the
respective adjustment knob.

43
5.21 Vehicle data recorder
Your vehicle is equipped with a Vehicle Data Recorder (VDR) / Seatbelt Monitor
System. The VDR monitors and records the following information:

 Engine RPM
 Engine Throttle Percentage
 Vehicle Speed
 ABS Events
 Transmission Range Information
 Parking Brake Position
 Master Warning Position
 Seat Occupied Status
 Seatbelt Status

The seat belt status screen will become visible if the park brake is released and an
occupant in the cab is not wearing their seatbelt. The seatbelt icon will illuminate
red for any occupant whose seatbelt is not fastened, green for any seated
occupant whose seatbelt is fastened, and gray for any empty seat. To manually
exit the seat belt status screen press any button except R4. The R4 button will
override this popup until the master power has been reset.

For more information please refer to the VDR manufacturer’s manual.

44
5.22 V-Mux controls
The vehicle has a centralized control system for most of the electrical items on the
apparatus. The Weldon Vista Display “Interface” module is where switching for
many components occurs, including the electrical lighting and HVAC controls on
the vehicle. The Vista Display will begin each session with a start-up display once
the Master Power Switch has been energized. The buttons surrounding the
screen are “toggle switches” that turn a function on and off or allow options to be
chosen. These buttons may also access additional screens. Since each V-Mux
system is unique, some of the following instructions may vary for your apparatus.

A) Emergency Lights Master Button E) System Info Screen

B) Warning Lights Screen F) Secondary Menu Screen
C) HVAC (Climate Control Screen) G) Home (Main Screen)
D) Lights Screen

5.22.1 Warning light activation

All warning lights can be activated through the press of a single button. The “E-
Master” button (A) will switch all warning lights on and off per the selections made
in the warning light menu (B).

NOTE: Any white warning lights will activate automatically with the release of the
park brake while the master warn light switch (A) is active per NFPA 1901.

5.22.2 Warning light menu

To access the warning light menu, press the “Warning Lt Menu” button (B).
Accessing this menu allows the user to switch certain warning lights on and off.

45
5.22.3 HVAC controls

By pressing the “HVAC” (C) button, the user can adjust several settings for the
heating and cooling system. These settings include:

 Defrost Mode which activates the heat valve and closes the air damper to allow
all heated air to pass over the windshield. This mode should be used
whenever there is buildup of ice on the windshield.
 Heat Mode also activates the heat valve while the air damper remains open
allowing the heated air to flow into the main portion of the cabin.
 A/C Mode activates the air conditioning condenser and freon compressor with
the air damper open allowing cooled air to flow into the main portion of the
cabin.

To select heat or air conditioning, press the button located beside the “Heat / A/C”
box.

To adjust the fan speed, press the button beside the “Fan Speed” box. Fan speed
selection consists of OFF, LOW, MEDIUM, OR HIGH.

To select defrost or vent settings, press the button beside the “Defrost / Vent” box.
The vent settings consist of defrost, vent, and off.

To adjust the temperature, use the buttons beside both the “Temp UP” and “Temp
Down” boxes. The temperature setting is displayed in the center of the V-Mux
screen.

5.22.4 Lighting

The “Lighting” button (D) controls auxiliary lighting such as dome lights and scene
lights. Press the button beside the box illustrating the light you would like to turn
on or off.

5.22.5 Secondary menu

The Secondary Menu (F) is generally used to gain access to the date/time
adjustment and backlight adjustment settings. To adjust the back light settings,
press the button beside the “Vista Back Light” box, the brightness level consists of
4 possible settings. To set the clock, press the button beside the “Date/Time
Adjust” box. Pressing this box will open up the date/time adjustment screen. To
change the value of any setting, simply press the button located beside the setting
you wish to change. Continue to press the button until the desired value is
reached.

46
5.22.6 Home

The Home button (G) is used to return to the Main Menu when the user has gone
to another menu. The main screen is unique to every apparatus. To adjust the
state of any item on the home screen, press the button beside the desired box.

5.22.7 Seat belt status

The seat belt status screen will become visible if the park brake is released and an
occupant in the cab is not wearing their seatbelt. The seatbelt icon will illuminate
red for any occupant whose seatbelt is not fastened, green for any seated
occupant whose seatbelt is fastened, and gray for any empty seat. To manually
exit the seat belt status screen press any button except R4. The R4 button will
override this popup until the master power has been reset.

5.22.8 Rear/side view camera

WARNING!
Camera/Monitor system aids in the use of, but does not replace vehicle side
& rear view mirrors. Objects in camera/monitor view may be closer than
they appear. When backing up, always be prepared to stop.

The V-mux will automatically display the rear view camera when the chassis is
shifted into reverse. If equipped, it will also display the left or right side camera
when the chassis turn signal is activated in the given direction.

47
6 Operation
6.1 Preparation for use
The following Pre-Start checklist is a guide for inspection after each operation.
Any defects should be reported to the Maintenance personnel for disposition and,
if necessary, corrected before the truck is placed back in service.
WARNING!
Fire helmets shall not be worn by persons riding in enclosed driving and
crew areas. Fire helmets are not designed for crash protection and they will
interfere with the protection provided by head rests. The use of seat belts is
essential to protecting fire fighters during driving.

CAUTION!
Equipment improperly prepared for operation is unsafe for use. If something
is noticed and requires attention, have it checked before the apparatus
leaves for operation. Even minor mechanical defects can lead to accidents
or personal injury. Pay attention to the operation manuals of equipment and
apparatus carried in the vehicle.

6.1.1 Before entering the apparatus

 The Pre-Start Checklist (next page) should be completed after every operation.
 Unless the truck is equipped with optional auto ejects, unplug electric and air
shorelines connected to apparatus.
 All occupants must understand the 3 points of contact for entering and exiting
the cab safely. This means that at least three points of your body, either two
hands and one foot or one hand and two feet, must be in touch with the
apparatus or the ground while ascending into or descending out of the cab.

6.1.2 Before driving the apparatus

 Turn the master power disconnect switch to the “on” position.
 Start the engine, refer to “Starting and stopping the engine” section.
 While the engine is warming up, check all gauges and tell-tales to ensure all
systems are operating within normal operating ranges.
 Adjust driver's seat for proper pedal position then adjust steering wheel.
 Make sure that all occupants have their seat belts fastened.
 Check door ajar light to ensure that all doors are securely closed.
 Check mirrors for proper alignment.
 In dark, low light, and/or foggy conditions, turn on headlights.
 If conditions require, turn on windshield wipers.
 Adjust HVAC controls to desired temperature and output setting.
 If emergency warning lights are required, switch on.
 While holding service brakes, release park brake.
 Place vehicle transmission into drive and release the service brakes to
advance forward.

48
6.1.3 Pre-start checklist

Check all locks and hold down devices for proper operation.
Check vehicle exterior for dents or damage.
Clean all lights, reflectors and mirrors, and check for broken glass.
Check for missing bolts, loose or damaged hoses and damaged wires.
Take inventory of removable equipment. Replace any missing or damaged items.
Turn on all truck lights and check for correct function.
Check air system for leaks.
Inspect all fire-fighting equipment for corrosion, damage or other defects.
Inspect wheel hubs, axles, transfer casing, and transmission for signs of leakage.
Check under the vehicle for fuel, oil, or coolant leakage.
Check engine belts.
Check engine coolant level.
Check engine oil level.
Check transmission fluid level.
Inspect all glass for cracks and discoloration. Check operation of sliding windows in cab.
Check operation and condition of seat adjusting mechanism.
Inspect each tire for correct inflation.
Inflate every tire to the recommended air pressure when tires are cold.
Inspect tires for uneven wear, chinks, or cuts.
Inspect rims for damage and inspect lug nuts.
To prevent damage, tires must not be cleaned with a high pressure steam jet.
Observe operation of all gauges.
Operate windshield washer and wiper.
Operate warning lights and alarm system.
Operate the horn, heater, and defroster.
Check fuel level, add fuel if necessary.
Check level of windshield washing agent, add if necessary.
Check service brakes for proper function.
Check for uneven or spongy action, dragging, squealing, or chatter when braking.
Test parking brake for proper function.
Check operation and general condition of cabin and compartment doors.
Visually inspect seals around doors for looseness and/or damage.

49
6.2 Starting and stopping the engine

WARNING!
Danger of injury due to exhaust fumes and hot exhaust temperatures!

 Exhaust fumes are toxic. Ensure that the engine is shut down whenever the
apparatus is inside an enclosed area, or steps are taken to evacuate the
exhaust fumes.
 Diesel exhaust fumes are classified by the state of California to cause cancer,
birth defects, and other reproductive harm.
 The engine exhaust system will become extremely hot during engine
operation. DO NOT operate near flammable or explosive material. Hot
exhaust components will cause severe burns.

CAUTION!
Damage to engine components!

 Do not use starting fluids such as ether.

 If the engine does not start within 20 seconds, release the engine start switch
and allow the starter motor to cool for one minute before attempting to start the
engine again.

6.2.1 Starting the engine

 Turn the master power disconnect switch to the “ON” position.

 Turn the ignition switch to the “ON” position. The apparatus will go through a
series of self-checks; wait for the checks to complete and notify Maintenance
of any problems. If the “wait to start lamp” is on, wait until it turns off, then
proceed to the next step.
 Push the engine start switch.
 When engine starts, release the engine start switch.
 As the engine idles, check voltage, oil pressure, and all other gauges.

6.2.2 Stopping the engine

 Ensure that the park brake is set.

 Ensure that the transmission is in neutral.
 Turn the ignition switch to the “OFF” position to shut down engine.
 Turn the master power disconnect switch to the “OFF” position.

For further information please refer to your engine manufacturer’s manual.

50
6.3 Driving the vehicle

DANGER!
Danger of fatal or severe injury due to driving when the vehicle is not ready!

Danger of injury and accidents due to driving with the stop engine indicator light or
low air pressure.

 Only drive the vehicle when the stop engine indicator light is inactive.
 Ensure the vehicles pneumatic system is at operational pressure.

WARNING!
Danger of severe injury due to unintentional movement of the vehicle!

Vehicle can roll if the parking brake or service brakes are not applied.

 Always apply the parking brake when the apparatus is to be stationary.

 Do not allow the vehicle to move while starting the engine.
 Do not shift the transmission and throttle the engine simultaneously.
 Never shift the transmission to neutral while driving, if no gear is selected there
is no engine brake effect. This can cause the vehicle to accelerate and may
cause an accident or serious injury.

NOTICE
Danger of transmission damage!

Transmission failure or damage due to a raised transmission oil temperature.

Prolonged idling in drive mode or reverse gear may result in overheating of the
transmission.

 Shift gear into neutral (N), if the vehicle is stopped for more than five minutes
with the engine running.
 Stop engine immediately if the check transmission indicator lamp is active.

6.3.1 General information

 Watch out for obstacles (e.g. rocks, potholes, ruts, tree stumps).
 Adjust speed to ground conditions. The steeper and rougher the terrain, the
lower the speed.
 Adjust speed well ahead of obstacles, uphill or downhill gradients.
 Secure equipment that is fixed to the vehicle.

51
6.3.2 Begin driving

 Switch on the engine.

 Please refer to the chapter “Starting and stopping the engine”.
 The transmission display indicates N for neutral gear selected.
 Let the engine idle for a short time.
 Do not drive under full load until proper operation temperature is reached
(except in an emergency).
 Actuate the service brakes.
 Please refer to the chapter “Braking”.
 Select desired transmission gear.
 Please refer to the chapter “Transmission controls”.
 The transmission display indicates the selected gear.
 Release parting brake.
 Please refer to the chapter “Parking brake”
 Actuate throttle pedal and drive off.
 Please refer to the chapter “Brake and throttle pedals”.
 Vehicle starts moving.

6.3.3 Select transmission range

WARNING!
Danger of injury to persons or damage to the vehicle due to open doors!

 Before starting to drive, close all cab and compartment doors.

 If the door ajar light activates while driving, stop the vehicle immediately and
assess the situation before proceeding.

Select transmission range.

 Select the desired transmission range.

 For normal driving conditions, select drive (D).
 Please refer to the chapter “Transmission controls”.
 The transmission display indicates the desired gear selected.

Change driving direction.

 Release the throttle pedal.

 Actuate the service brake and stop the vehicle, taking account the traffic
situation.
 Let the engine idle.
 Select the desired mode by actuating the corresponding button.
 Release the service brakes.
 Actuate the throttle pedal and drive off.

52
6.3.4 Acceleration

Acceleration

 Actuate the throttle pedal to increase engine speed.

 Engine speed increase.
 Release the throttle pedal to allow the engine to return to idle.
 Engine speed decrease to idle.

6.3.5 Stopping and parking the vehicle

Parking the vehicle

 Stop the vehicle, taking account of the traffic situation.

 Set the parking brake.
 Shift the transmission to neutral (N).

Stopping the vehicle briefly

 If stopping briefly (e.g. traffic light), remain in the selected drive mode.
 Actuate the service brakes when stopping for a short period of time.
 Set the parking brake whenever necessary.

53
6.4 Braking the vehicle

NOTICE
Damage to overheated brakes!

The brake drums or disks become very hot immediately after extended periods of
driving down steep inclines, emergency braking, braking from high speed or
repeated braking in quick successions. Incorrect handling can cause damage to
the brakes.

 Before applying the parking brake, allow hot driving brakes to cool.
 When parking the vehicle with hot brakes, always use chocks.
 Do not drive through water when the brakes are hot.

6.4.1 Brake air pressure

If either the primary air pressure or secondary air pressure gauges indicate low
pressure, respond as follows.

 Ensure the parking brake is applied and the transmission is in neutral (N).
 Run the engine at high idle and observe the air pressure gauges.
 If the brake air pressure is not increasing, switch off the engine and obtain
workshop assistance.

If an alarm condition remains active after the engine has started:

 Identify the fault.

 Take appropriate action to rectify the fault, or shut down the engine.
 Obtain workshop assistance.

6.4.2 Parking brake

DANGER!
Danger of fatal or severe injury due to unintentional vehicle movements!

Unintentional vehicle movements can cause fatal injury to the crew or pedestrians.
Before leaving the cabin, the driver must:

 Park the vehicle on a safe surface.

 Select transmission to neutral (N).
 Apply the parking brake.
 Chock the wheels of the vehicle with the attached wheel chocks before
maintenance and repair work.

54
 NOTICE
Damage due to frozen brakes!

Wet service brakes may freeze up in freezing temperatures.

 Do not use the parking brake in freezing temperatures, if the service brakes
are wet.

Avoid stopping the vehicle immediately after heavy loading, when all systems are
hot. If possible without endangering, continue driving with the vehicle so that the
systems can drop back down to normal operating temperature.

 Continue driving slowly without pressing the service brake so that the brakes
have enough time to cool down.
 When the vehicle needs to be parked, secure the wheels with wheel chocks
instead of applying the parking brake.
 Wait until the brakes have cooled down.
 Apply the parking brake and place the wheel chocks back into storage.

Apply parking brake.

 Pull parking brake valve.

 Parking brake is applied.
 Park brake engaged indicator is lit.

Release parking brake.

 Push parking brake valve.

 Parking brake is released.
 Park brake engaged indicator is off.

55
6.4.3 Service brake

WARNING!
Danger of injury and accidents! Vehicle cannot be driven!

An adequate braking effect cannot be assured if the air tank pressure in brake
circuits 1 or 2 is too low.

 Stop immediately, observing the current traffic situation.

 Run engine in high idle until sufficient pressure builds up.
 If pressure does not build up, do not drive the vehicle.
 Troubleshooting and/or obtain workshop assistance.

Danger of fatal or severe injury due to improper use of the braking system!

Repeated braking, pulse braking, a leak in the compressed air system, or the use
of the parking brake while driving, reduces the operating pressure; this in turn
could result in locking up of the wheels and can cause severe accidents.

 Ensure correct compressed air system and braking system operations.

 Do not start driving if the compressed air pressure in the braking system is too
low.
 If the warning lights for the brake system or compressed air system come on,
stop the vehicle immediately and do not continue until the issue has been
resolved.
 Avoid repeatedly depressing and releasing the brake pedal.
 Never use the parking brake as a service brake while driving.
 Report malfunctions to your work shop personnel as quickly as possible and
make sure that the repair is performed.
 Avoid overheating the service brakes.

A large enough loss of air pressure puts the service brake out of operation and
causes the parking brake to be applied automatically.

Apply service brakes.

 Actuate the service brake pedal.

 Service brakes are applied.

Release service brakes.

 Release the service brake pedal.

 Service brakes are released.

56
6.5 Cab tilt procedure
6.5.1 Remote electric operation

WARNING!
Danger of severe injury or death!

 Before raising or lowering the cab, safety precautions must be taken to avoid
personal injury or equipment damage. Ensure frontal and overhead clearance
is sufficient to fully raise cab without hitting electrical wires or dangerous
overhead objects that could result in serious injury or death.
 Failure to ensure that the mechanical support is in place may result in personal
injury or death.
 Remove loose items from cab and ensure the doors are closed and completely
latched to avoid a shift in contents or sudden opening of doors.

CAUTION!
Danger of death, injury and equipment damage! Do not raise the cab until
the following procedures have been followed:

 Vehicle must be parked on level surface with park brake applied.

 No personnel or loose equipment should remain in cab during tilt system
operations.
 Cab doors must be securely closed prior to the tilt operations.
 Be sure there is adequate clearance in front of and overhead of cab to fully
raise the cab without contacting objects including, but not limited to, items in or
around the bumper and cab overhead (i.e. vehicle equipment, surrounding
obstacles, power lines, etc.).
 Master switch must be in the “ON” position.
 Ignition switch may be in the “OFF” position, or “ON” position, with or without
the engine running.
 All personnel must stay clear of area under and in front of the cab at all times
while the tilt system is in operation and until the mechanical support is
engaged.

57
 Raising cab (remote electric)

1. Locate the cab pendant control. Plug in if necessary.

2. Energize the electric/hydraulic pump by depressing and holding the “UP”
button on the pendant until the mechanical support drops into place against the
cylinder. The pendant light will come on indicating the latches are unlocked.
Continue to raise the cab until there is a visible gap between the mechanical
support and the top of the tilt cylinder housing (1/8 inch).
3. Deactivate the electric/hydraulic pump by releasing the "UP" button.
4. Do not lower the mechanical support onto the top of the cylinder! Visually
confirm that the mechanical support is engaged before personnel move under
the raised cab.

Lowering cab (remote electric)

1. Clear all personnel and equipment from chassis/under raised cab.

2. Pull the mechanical support release cable until the support clears the cylinder
and until the bottom of the support is below the top of the cylinder as the cab is
lowered.
3. Energize the electric/hydraulic circuit by depressing and holding the “DOWN”
button on the pendant until the cab has completely lowered, the latches have
engaged and the pendant light has been off for 15 seconds.
4. Deactivate the electric/hydraulic circuit by releasing the “DOWN” button.

Cab pendant Mechanical

control support

1/8 inch gap

Pendant light

58
6.5.2 Manual pump operation

WARNING!
Danger of severe injury or death!

 Before raising or lowering the cab, safety precautions must be taken to avoid
personal injury or equipment damage. Ensure frontal and overhead clearance
is sufficient to fully raise cab without hitting electrical wires or dangerous
overhead objects that could result in serious injury or death.
 Failure to ensure that the mechanical support is in place may result in personal
injury or death.
 Remove loose items from cab and ensure the doors are closed and completely
latched to avoid a shift in contents or sudden opening of doors.

CAUTION!
Danger of death, injury and equipment damage! Do not raise the cab until
the following procedures have been followed:

 Vehicle must be parked on level surface with park brake applied.

 No personnel or loose equipment should remain in cab during tilt system
operations.
 Cab doors must be securely closed prior to the tilt operations.
 Be sure there is adequate clearance in front of and overhead of cab to fully
raise the cab without contacting objects including, but not limited to, items in or
around the bumper and cab overhead (i.e. vehicle equipment, surrounding
obstacles, power lines, etc.).
 Master switch must be in the “ON” position.
 Ignition switch may be in the “OFF” position, or “ON” position, with or without
the engine running.
 All personnel must stay clear of area under and in front of the cab at all times
while the tilt system is in operation and until the mechanical support is
engaged.

59
 Raising cab (manual pump)

1. Close the “I” valve on the hand pump. Make sure the “L” valve on the hand
pump is closed.
2. Operate the pump until the mechanical support drops into place against the
cylinder. Continue to pump until there is a visible gap between the mechanical
support and the top of the tilt cylinder housing (1/8 inch).
3. Do not lower the mechanical support onto the top of the cylinder! Visually
confirm that the mechanical support is engaged before personnel move under
the raised cab.

Lowering cab (manual pump)

1. Clear all personnel and equipment from chassis/under raised cab.

2. Pull the mechanical support release cable until the support clears the cylinder
and until the bottom of the support is below the top of the cylinder as the cab is
lowered.
3. Open the “L” valve to lower the cab. Leave the valve open until the cab has
completely lowered and the latches have engaged, and the pendant light has
been off for 15 seconds.
4. Close the “L” valve and open the “I” valve two full turns.

Make sure to reset the “I” and “L” valves to their normal positions after the cab has
been lowered. If the “I” valve is left closed during normal operations (i.e. driving
over a very bumpy road or under very hot conditions) the cab latches may open.

“ L ” valve
Normally closed - tightened
clockwise by hand with pump handle

“ I ” valve
Normally open - two turns
counterclockwise with pump handle

The manual pump has two valves—one marked “L” and one marked “I”. The “I” is
for “isolation” valve and is normally open (two turns counterclockwise). The “L” is
for “lower” valve and is normally closed (tightened clockwise by hand with the pump
handle). The normal positions are for any operating mode except manual pump
operation.

60
6.6 Emission control system

WARNING!
Danger of injury due to hot exhaust temperatures!

 Active regeneration can occur any time the vehicle is moving, and the exhaust
temperature can remain hot after the vehicle has stopped moving. The
exhaust temperature could reach 1500°F, which is hot enough to ignite or melt
common materials, or to burn people.
 During regeneration, exhaust gas temperature could reach 1500°F, and
exhaust system surface temperature could exceed 1300°F, which is hot
enough to ignite or melt common materials, and to burn people. Engine speed
will increase and could possibly reach between 1000 to 1500 RPM.
 The exhaust system can get extremely hot without warning. Do not park
vehicle near flammable material. Do not touch exhaust pipes or parts. Stay
clear of exhaust gas. Hot metal and exhaust gas can burn skin.
 IMPORTANT: See your engine operation manual for complete details and
operation of the diesel aftertreatment system.

Overview
The aftertreatment diesel particulate filter lamp (pictured) indicates, when
illuminated or flashing, that the aftertreatment diesel particulate filter requires
regeneration. If illuminated indicates that the aftertreatment diesel particulate filter
needs to be regenerated at the next possible opportunity. This can be
accomplished by:

 Changing to a more challenging duty cycle, such as highway driving, for at

least 20 minutes.
 Performing a stationary regeneration. Follow the instructions in the “Stationary
(parked) Regeneration” section of this manual.

A flashing aftertreatment diesel particulate filter lamp indicates that the

aftertreatment diesel particulate filter needs to be regenerated at the next possible
opportunity. Engine power may be reduced automatically. When this lamp is
flashing, the operator should:

 Change to a more challenging duty cycle, such as highway driving, for at least
20 minutes.
 Performing a stationary regeneration. Follow the instructions in the “Stationary
(parked) Regeneration” section of this manual.

A flashing aftertreatment diesel particulate filter lamp combined with an illuminated

warning or check engine lamp indicates that the aftertreatment diesel particulate
filter needs to be regenerated immediately. Engine power will be reduced
automatically. When these lamps are illuminated, a stationary regeneration is

61
 required. Follow the instructions in the “Stationary (parked) Regeneration” section
of this manual.

NOTE: If a stationary regeneration is not performed, the STOP ENGINE lamp will
illuminate and the vehicle will need to be taken to a Cummins® Authorized Repair
Location.

Passive and Active Regeneration

This aftertreatment system has many specialized parts in order to make our
engines cleaner and more environmentally friendly. First, the particulate filter
collects and oxidizes carbon to remove particulate matter from the exhaust. Then,
the SCR catalyst converts NOx into harmless gas and water vapor.

Passive regeneration occurs when the exhaust temperatures are naturally high
enough to oxidize the soot collected in the aftertreatment diesel particulate filter
faster than the soot is collected. Passive regeneration typically occurs when the
vehicle is driven at high speeds (ie, highway speeds) and/or under heavy loads.

Active regeneration occurs when the exhaust temperatures are not naturally high
enough to oxidize the soot collected in the aftertreatment diesel particulate filter
faster than it is collected. Active regeneration requires assistance from the engine
in order to increase the exhaust temperature. This is typically accomplished by the
engine injecting a small amount of diesel fuel into the exhaust stream, which is
then oxidized by the aftertreatment diesel oxidation catalyst, which creates the
heat needed to regenerate the aftertreatment diesel particulate filter.

Stationary (parked) Regeneration

Under some operating conditions, such as low speed, low load, or stop and go
duty cycles, the engine may not have enough opportunity to regenerate the
aftertreatment diesel particulate filter during normal vehicle operation. When this
occurs, the engine will illuminate the aftertreatment diesel particulate filter lamp to
inform the driver that assistance is required, typically in the form or a stationary
(parked) regeneration. Stationary (parked) regeneration is a form of active

62
 regeneration that is initiated by the vehicle operator when the vehicle is not
moving. Stationary regeneration requires an elevated engine speed of
approximately 1000 to 1400 RPM. The length of a stationary regeneration will
vary depending on how full the aftertreatment diesel particulate filter is, but will
typically take anywhere from 45 minutes to 1.5 hours to complete.

To perform a stationary regeneration follow the steps listed:

 Select an appropriate location to park the vehicle.

 Preferably on a surface that will not burn or melt under high exhaust
temperatures (such as clean concrete or gravel, not grass or
asphalt).
 Park the vehicle away from anything that can burn, melt or explode.
 Ensure there are no items within 2 feet of the exhaust outlet.
 Items that can burn, melt or explode must be kept at least 5 feet
from the exhaust outlet (such as gasoline, paper, plastics, fabrics,
compressed gas containers, hydraulic lines).
Exhaust
 Ensure that there are no gasses or vapors nearby that could burn,
Outlet
explode or contribute to a fire (such as LP gas, gasoline vapors,
oxygen, and nitrous oxide).
 Park the vehicle securely. Place transmission in neutral and set parking brake.
Set wheel chocks at front and rear of at least one tire.
 Set up a safe exhaust area. If bystanders might enter the area, set up barriers
to keep people at least 5 feet from the exhaust outlet during stationary
regeneration. When indoors, attach an exhaust discharge pipe rated for at
least 1500°F.
 Keep a fire extinguisher nearby.
 Check the exhaust system surfaces. Confirm that nothing is on or near the
exhaust system surfaces (such as tools, rags, grease, or debris).
 Verify the following conditions are met in the vehicle.
 The brake pedal is released.
 The transmission is in neutral.
 PTO or Remote PTO is off.
 The vehicle speed is 0 MPH.
 The throttle pedal is released.
 Initiate the stationary regeneration by toggling the REGEN switch.
 Once the stationary regeneration is initiated, the engine speed will
increase, and turbocharger noise will increase.
 The High Exhaust System Temperature Lamp may illuminate during
stationary regeneration as the exhaust temperatures increase.
 When the engine ECM detects that the aftertreatment diesel
particulate filter has been regenerated, the engine will automatically
return to normal idle speed.

63
  Monitor the vehicle and surrounding area during the stationary regeneration.
If any unsafe condition occurs, shut off the engine immediately.

Once the stationary regeneration is complete, exhaust gas and surface

temperatures will remain elevated for 3 to 5 minutes.

NOTE: To stop a stationary regeneration before it has completed, depress brake

or throttle pedal, or turn off the engine.

Regeneration Inhibit Switch

The “REGEN INHBT” switch is used to delay the regeneration process when it is
unsafe to allow the process to proceed due to hazardous conditions, such as
flammable or explosive conditions near the exhaust. Turning the switch on will
prevent both active and parked regeneration from occurring. Once it is safe to
proceed, manual activation should be activated, and may require 45 to 90 minutes
to complete. Engine ECM will automatically turn off regeneration when completed.

The “REGEN INHBT” switch should only be used in hazardous situations. Failure
to allow the engine to regenerate will eventually lead to engine damage.

For more information please refer to your Cummins manual.

64
6.7 Diesel exhaust fluid (DEF) tank

WARNING!
Danger of injury due to bodily contact!

 Do not allow diesel exhaust fluid (DEF) to contact the eyes. In case of contact,
immediately flood eyes with large amounts of water for a minimum of 15
minutes.
 Avoid prolonged contact with skin. In case of contact, wash skin immediately
with soap and water.
 Do not take internally. If fluid is ingested contact a physician immediately.

CAUTION!
Damage to the engine or emission control system may result!

 It is unlawful to tamper, alter, or remove the after treatment system or use

unapproved DEF solutions.

DEF tank The Diesel Exhaust Fluid (DEF) tank is located under the cab on the driver’s side
near the battery compartment. This vehicle is equipped with an indicator on the
DEF tank dash that will alert the driver of the quantity of DEF on board (See Dash gauges
access door and tell-tales section of this manual). If the vehicle is operated such that one
would run completely out of DEF, vehicle power will be reduced enough to
encourage the operator to refill the DEF tank. Once the tank has been refilled the
engine will resume normal power levels.

Your apparatus may be equipped with a DEF tank access door. This access door
is located in the step well of the rear door on the driver’s side. The access door
provides easy access to the DEF tank’s fill cap. If your apparatus is not equipped
with a DEF tank access door, the cab must be raised to access the DEF tank.
Instructions on how to raise the cab can be found in the “Cab Lift Procedure”
section of this manual.

65
7 Service and cleaning
7.1 Service plan
The following checklist helps to ensure that the vehicle parts are in a good
operating condition.

Plan enough time for assessment and inspection work.

Assessment and inspection work may only be carried out by correspondingly

trained fire-fighting personnel, who are familiar with the vehicle. Service must be
carried out depending on the operating time or the hours of operation, whichever
comes first.

If a system or a component does not pass this assessment, rectify the problem
before starting up the vehicle. Always when equipment parts have to adjusted,
renewed or lubricant changed, see corresponding chapter or maintenance guide,
there are instructions, specifications and other service intervals listed there.

Before servicing a vehicle, proceed as follows:

 Park the vehicle on a flat, even surface.

 Select neutral (N), activate the parking brake and secure the wheels with
wheel chocks.
 Switch off the ignition.
 Set up and use guard rails
 Ensure that the battery main switch is deactivated and an instruction plate is
attached.
 Ensure that the supply lines to the vehicle are disconnected.

To check the exterior of the vehicle, it is recommended to go around the vehicle

clockwise, beginning with the right front wheel.

Observe the operation and maintenance manual of the engine manufacturer.

66
7.1.1 Inspection procedures

Testing and inspection work

 Service must be carried out depending on the operating time or the hours of
operation, whichever comes first.

Authorized specialist
Every 12 months or

Every 24 months or

Every 36 months or

Every 60 months or

Every 72 months or
1350 hours

2250 hours

2700 hours
450 hours

900 hours

Operator
Weekly
Daily
Work description
Check compressed air lines.  
Check vehicle underside and planetary gears
 
for fluid loss (visual check).
Check the vehicle for obvious oil, coolant and
 
fluid leaks.
Check the vehicle underside for obvious
 
damage.
Check the tightening torque of the chassis
 
(one-time during first service).
Check the screw connection of the chassis
 
for tight fit.
Check supports and fastenings for tight fit
 
and damage.
Check lighting for damage and dirt. Clean if
 
necessary.
Check the condition of windshield wipers and
 
windshield washer nozzles.
Check the functionality of the windshield
 
washer and wipers.
Check level of windshield washing agent
 
fluid. Fill if required.
Check the condition and safety of the doors.  
Check axle location and suspension
 
components.
Check brake hoses and braking cylinder for
 
damage.
Check tires for damage.  
Check that tires are inflated to correct
 
pressure.
Check batteries, battery cables, and battery
 
cover are in a safe condition.
Check the oil level in the power-assisted
 
steering container.
Check engine oil level.  
Check engine for deposits, leaks and loose
 
connections.

67
 Authorized specialist
Every 12 months or

Every 24 months or

Every 36 months or

Every 60 months or

Every 72 months or
1350 hours

2250 hours

2700 hours
450 hours

900 hours

Operator
Weekly
Daily
Work description
Check exhaust system (visual check)  
Check fuel/water separator for discolorations
 
and drain water if present.
Check power supply socket for safe
 
condition.
Check exterior of the radiator and the
intercooler for leaks and deposits of dirt.  
Remove dirt if necessary.
Check radiator and intercooler suction pipe
 
for damage and/or deposits of dirt.
Check air filter inserts and pilot lamp.  
Check steering components.  
Check gearbox oil level.  
Check engine coolant level.  
Check steering wheel for safe condition and
 
excessive play.
Check seats and safety belts for secure
 
attachment and damage.
Check the condition of the access points and
 
the floor in the driver’s cab.
Check alarms, fittings, pilot lamps, and
 
buzzer for correct functionality.
Check front, middle and rear differential locks
 
(if applicable)
Check engine oil pressure and coolant
 
temperature.
Check the heating and/or air-conditioning fan.  
Check the functionality of the reversing alarm
 
and reversing camera (if applicable).
Operate the air conditioning for at least 10
 
minutes and check for proper functionality.
Check hoses and clamps.  
Check the engine belts.  
Check the alternator and batteries.  
Inspect the suspension.  
Check the fluid level of the axles.  
Check the central lubrication of the axles.  
Check tightening torque of the wheel and rim
 
nuts.
Check air drier.  
Inspect brake drum and brake pads.  
Inspect brake disks and brake pads (if
 
applicable).

68
 Authorized specialist
Every 12 months or

Every 24 months or

Every 36 months or

Every 60 months or

Every 72 months or
1350 hours

2250 hours

2700 hours
450 hours

900 hours

Operator
Weekly
Daily
Work description
Inspect the steering.  
Check the oil level in the power-assisted
 
steering container.
Drain compressed air tank.  
Inspect the cooling system anti-freeze.  

7.1.2 Oil and filter interval

Oil and filter replacement interval

 Service must be carried out depending on the operating time or the hours of
operation, whichever comes first.

Authorized specialist
Every 200,000 miles
Every 24 months or

Every 48 months or
Every 6 months or

Every 6500 hours

Every 3rd to 4th oil

change interval
or 320,000 km
2000 hours

5000 hours
500 hours
Weekly
Daily

Work description
Replace engine oil and filter*  
Fuel filter  
Coolant filter  
Overhead adjustment  
Standard coolant change  
DEF filter  
Particulate filter cleaning  
Coalescing filter  

*Assuming severe duty cycle for fire/emergency vehicle applications.

Please refer to your engine manufacturer’s manual for more information.

69
7.2 Transmission maintenance
This Allison Transmission has an available prognostics feature which monitors the
transmission’s fluid, filters, and overall health. The wrench icon illuminates when
remaining fluid life reaches 1%. Afterwards, every time the vehicle is started and
D (Drive) is selected the wrench icon illuminates again and stays on for two
minutes to remind the operator a fluid change is needed. This occurs until service
is performed and the oil life monitor is reset.

The wrench icon flashes on and off for two minutes after D (Drive) is selected.
Once the filter life monitor mode has been accessed via the shift selector, the “oK”
or “Lo” message is displayed in the selector display window. “oK” means the filters
do not need to be changed, and “Lo” means the filters need to be changed.

Calendar based fluid requirements still apply with prognostics (refer to Allison
manual). If the oil life monitor has not indicated the need for a fluid change before
60 months for TES 295 fluid, or 24 months for TES 389 fluid, it is necessary to
change the fluid and filters per calendar requirements and then reset the oil life
monitor.

Instructions on how to read and reset the oil life monitor and filter life monitor along
with calendar based maintenance schedules can be found in the Allison®
Transmission supplied operators manual.

Please refer to your Allison manual for more information.

70
7.3 Filter information
Air filter Donaldson P541575
Ember separator Parker-Racor 123970012
Engine oil filter Fleetguard LF9009
Engine Coolant Filter Fleetguard WF2071
Secondary Fuel Filter Fleetguard FF63008
Fuel filter / water separator Fleetguard FS19764

7.4 Fluid capacities

Engine Oil 15W40 25.2 QTS 23.8 L
Engine Coolant ELC 40.0 QTS 37.8 L
Transmission Fluid ATF 29.0 QTS 27.4 L
Power Steering Fluid ATF 8.00 QTS 7.57 L
Cab Tilt Mechanism Fluid ELC 40.0 QTS 41.6 L
Air Conditioning Refrigerant R-134A 7.00 LBS 3.18 KG
Air Conditioning Oil PAG 46 7.00 OZ 0.21 L
Diesel Fuel Tank Diesel 68.0 GAL 257 L
Diesel Exhaust Fluid DEF 20.0 QTS 18.9 L
Steer Axle Fluid 80W90 1.00 PINT 0.47 L
Drive Axle Fluid 80W90 37.0 PINT 17.0 L

*Actual fluid capacities may be slightly different for your apparatus.

71
7.5 Under cab overview

C
B E

D G

J
G

A) Engine coolant fill H

B) Cab lift mechanical support
C) Engine oil dipstick
D) Secondary fuel filter
E) Engine coolant filter (optional)
F) Cab heater shutoff valves
G) Transmission oil dipstick
H) Chassis air drier
I) Engine oil filter
J) Engine air filter housing

72
7.6 Engine oil level
The engine oil level should be checked prior to engine ignition. Follow these steps
to inspect the engine oil level:

 Make sure the vehicle is parked on a level surface.

 Turn the engine off and wait 10 minutes for the oil to drain into the oil pan.
 Remove the engine oil dipstick and wipe it with a clean cloth.
 Replace the dipstick and remove it again to check the oil level.

Oil level should be between the low and high marks on the dipstick. Add or
remove oil as necessary. Refer to the fluid capacities section for engine oil type.

Refer to your engine manufacturer’s manual for more information.

7.7 Engine cooling system

CAUTION!
Do not touch heater hoses, radiator hoses, or other engine components they
can be very hot. Never remove radiator cap while engine coolant is hot.

A positive de-aeration cooling system comprised of a surge tank and vent line from
the engine and radiator along with a fill line from the surge tank to the engine water
pump is used on this apparatus.

Coolant type and filling instructions:

NOTE: Do not mix coolant types. If coolant type is changed, it is recommended

that a complete coolant flush be done.

Engine coolant 1. Refer to data provided in the chassis or engine manual for acceptable types of
level sight coolant and coolant capacity.
glass 2. Use only approved coolant to fill coolant system through the fill neck on the top
of the surge tank.
3. Run engine at max torque until the thermostat opens (190 – 195 F).

NOTE: It may be necessary to regulate the air flow through the radiator to get the
coolant temperature high enough for the thermostat to open.

4. Once operating temperature is achieved, shut off engine and refer to sight
glass to check the fluid level. (Coolant level should be in the middle of sight
glass.)
Front grille 5. Add necessary quantity of appropriate coolant to bring coolant level entirely
into the sight glass.

NOTE: Coolant may need to be topped off after normal operation of the engine or
if service work has been performed.

Refer to your engine manufacturer’s manual for more information.

73
7.8 Transmission fluid level
CAUTION!
A low or high fluid level can cause overheating and irregular shift patterns.
Incorrect fluid level can damage the transmission.

 Park the vehicle on a level surface.

 Shift to Neutral and apply the parking brake.
 Press the Up and Down Arrow buttons simultaneously once.

NOTE: The fluid level check may be delayed until the following conditions have
been met:
 The fluid temperature is above 60°C (140°F) and below 104°C (220°F).
 The transmission is in Neutral.
 The engine is at idle.
 The transmission output shaft is stopped.
 The vehicle has been stationary for approximately two minutes to allow the
fluid to settle. A delayed fluid level check is indicated by a “—” in the single
digit display followed by a numerical countdown. The countdown, from 8 to
1, indicates the time remaining in the two minute waiting period.

 If the fluid level is correct, the display will show the following:
SELECT MONITOR Description
o L Represents Fluid (oil) Level Check Mode
o K Fluid level is within the correct fluid level zone
NOTE: The sensor display and the dipstick may not agree exactly because the
OLS compensates for fluid temperature.

 If the fluid level is low, the display will show the following:
SELECT MONITOR Description
o L Represents Fluid (oil) Level Check Mode
L o Represents Low Oil Level
0 2 The number of quarts the transmission is low

 If the fluid level is high, the display will show the following:
SELECT MONITOR Description
o L Represents Fluid (oil) Level Check Mode
H I Represents High Oil Level
0 1 The number of quarts of fluid the transmission is
overfull

 If there is a system problem, the display will show the following:

SELECT MONITOR Description
o L Represents Fluid (oil) Level Check Mode
– – The dashes are followed by a numerical display which is a
fault code that indicates conditions are not proper to receive
the fluid level information or there is a system malfunction.

 To exit the fluid level display mode, press any range button on the pushbutton
shift selector.
Please refer to your Allison manual for more information.

74
7.9 Power steering fluid level
Fill cap/dipstick To check the power steering fluid reservoir level follow these steps:

 Unscrew the fill cap/dipstick on top of the power steering fluid reservoir.
 Remove the fill cap/dipstick from the reservoir.
 Wipe the dipstick with a clean cloth.
 Replace the fill cap/dipstick and screw fill cap completely closed.
 Remove the fill cap/dipstick again to check the fluid level.

The fluid level should be between the low and high marks on the dipstick. Add or
remove fluid as necessary. Refer to the fluid capacities section for power steering
fluid type.

7.10 Fuel filter/water separator

CAUTION!
When closing the drain valve, do not over tighten the valve. Over tightening
can damage the threads.

This apparatus is equipped with a fuel filter / water separator. The water and
sediment that this filter collects should be drained daily. Follow these steps to
drain the fuel filter / water separator.

 Shut off the engine.

 Use your hand to open the drain valve located on the bottom of the filter. Turn
the valve counterclockwise to loosen until draining occurs.
 Drain the filter sump until clear fuel is visible.
 To close the valve, lift the valve and turn clockwise until it is hand-tight.

7.11 Windshield wipers and washer fluid

WARNING!
If your vehicle is operated in temperatures below 40°F (5°C), use washer fluid
with antifreeze protection. Failure to use washer fluid with antifreeze
protection in this environment could cause the windshield washing fluid to
freeze which will inhibit windshield washing operations.

A well-conditioned set of windshield wipers is vital to any vehicle. Wiper blades

should be inspected monthly and replaced when necessary. To check the wiper
blades, run the tip of your fingers over the edge of the blade and check for
roughness. To clean, wipe the blades with washer fluid, rubbing alcohol, or water
applied to the tip of the blade with a clean cloth.

Add windshield washer fluid to the reservoir if the level is low. Remember to use a
windshield washer fluid suitable for your weather conditions.

75
7.12 Batteries
WARNING!
Batteries can give off explosive gases. Do not allow flames, sparks or
lighted substances to come near the battery.

Always wear protective clothing and eye protection. To reduce the risk of
injury, vent battery compartment before servicing and always disconnect the
negative ground (-) wire first and attach the negative ground (-) wire last.

CAUTION!
When using jumper cables to start the engine, make sure to turn master
battery switch off and connect the positive (+) cable to the positive (+)
terminal and the negative (-) cable to the negative (-) terminal.

Always keep the top of the batteries clean and dry. Also make sure that battery
cables are always tightly fastened. If you notice any corrosion on the battery or
battery terminals, remove the cables and clean with a wire brush. To ease clean
up, the battery acid can be neutralized with a solution of baking soda and water.
Battery terminals may be installed with a dielectric compound, coated with battery
terminal spray, or clear polyurethane spray.

When battery replacement is required, the battery should only be replaced by a

battery that meets the same electrical requirements as the original. Always
remove all negative battery terminals first when disconnecting a battery. When
installing a battery, install the positive terminals first. Install the negative terminals
last. Clean all battery terminals to assure a proper connection.

7.13 Engine air filter

WARNING!
Do not start your engine with the air cleaner removed or remove your air
filter while the engine is running.

The air filter should be inspected monthly. Follow these steps to remove and
inspect the air filter.

 Remove the four screws holding the cover of the air filter housing.
 Carefully remove the cover to the air filter housing.
 Remove the air filter element from the air filter housing.
 Inspect air filter element, replace if necessary.
 Wipe any dirt or debris from the air filter housing and cover.
 Carefully place air filter element back into housing.
 Replace cover onto the air filter housing.
 Replace the four screws to hold the cover on the air filter housing.

76
7.14 Tires and wheels
WARNING!
Always make sure tires are in good condition and inflated to the correct tire
pressure. Frequently check and maintain correct inflation pressures as
specified by the tire manufacturer. Periodically examine tires for abnormal
wear and other damage. Only properly trained personnel with the correct
equipment and procedures should mount or remove tires.

CAUTION!
Check for proper inflation, tread depth, and the condition of the tires daily.
Look for any bumps, blisters, cuts, punctures, cracks, or uneven wear. Tire
condition and pressures must be monitored closely to assure safe operation
of the vehicle.

Never use the hub piloted wheels which have straight holes with ball seat or
spherical chamfer nuts. These parts are not engineered to work together and
can cause premature wheel failure. On heavy truck dual wheels, this
mismatch would not allow the inner cap nut to fit into the inner wheel,
causing the inner cap nut to interfere with the outer wheel. This could cause
premature cracking and failure of the outer dual wheel.

Stud piloted wheels should not be used with hub piloted hubs, wheels, or
flange nuts. Chamfered stud piloted wheels do not have sufficient surface
area near the bolt hole to support the flange nut. This type of mis-assembly
may lead to loss of torque, broken studs, and cracked wheels.

Hub Piloted Mounting

These wheels are often called hub mount wheels and center on the hub at the
center hole or bore of the wheel. Because of this feature, they need a close
tolerance in the center hole. Hub piloted wheels are used with two-piece flange
nuts (see figure) which contact the disc face around the bolt hole and do not rely
on contacting the bolt hole chamfer to function properly. Hub piloted wheels
generally have straight-through bolt holes with no chamfers. This feature provides
a visual way of identifying hub piloted wheels.

Before Installing Wheels

Completely remove rust, dirt, and other foreign materials from all surfaces. It is
especially important to clean the areas used for mounting the wheel to the vehicle.
Lubricate the hub pilot pads with a drop of oil to prevent galling. Also, apply two
drops of oil to the last two or three threads at the end of each stud. Do not
lubricate any other wheel or hub surfaces. If reusing flange nuts that have already
been used in service, apply 2 drops of 30 weight oil at one point between the
flange and the hex (see figure). This will allow the parts to rotate freely and
provide the proper clamping force when tightened.

77
 Installing Front Wheels
Slide front wheel over studs. Be careful not to damage the stud threads. Snug up
2 piece flange nuts in the sequence shown in figure. Do not tighten them fully until
all have been seated. This procedure will permit the uniform seating of nuts and
ensure the even, face-to face contact of wheels, hub, and drum. Tighten 2 piece
flange nuts to 450-500 ft.-lbs. (dry) using the same crisscross sequence.

Installing Dual Rear Wheels

Slide the inner dual wheel over studs. Be careful not to damage the stud threads.
Align the hand holes of the outer dual wheel to those of the inner dual wheel to
allow access to the air valves. Slide the outer dual wheel over the studs, again
being careful not to damage the stud threads. Snug up 2 piece flange nuts in the
sequence shown in figure. Do not tighten them fully until all have been seated.
This procedure will permit the uniform seating of nuts and ensure the even, face-to
face contact of wheels, hub, and drum. Tighten 2 piece flange nuts to 450-500 ft.-
lbs. (dry) using the same crisscross sequence. Hub mount wheels use two-piece
flange cap nuts for both the front and rear applications. No inner cap nuts are
required.

Note: After the first 50 to 100 miles of operation, recheck the torque level and
retighten nuts to the proper torque level.

Replacement
When replacing wheels and tires on this apparatus, the replacement equipment
must have the same load carrying capacity as the original. Wheels must have the
same characteristics such as rim width, rim offset, and mounting configuration,
while tires must be of the same size and type, and must conform to government
regulations.

Note: The front and rear wheels on this apparatus are NOT interchangeable. The
front wheels are heavy duty and can withstand higher loads. Do not mix!

78
7.15 Normal operating range
Idle: 600 – 700 RPM
High Idle: 1250 RPM/Varies
Governor: 2100 – 2400 RPM
Min. Oil Pressure @ Normal Idle: 10 psi
Cooling System: 180 - 212°F
Transmission: 160 - 225°F
Air Pressure: Cut In: 105 – 110 psi
Air Pressure: Cut Out: 120 – 140 psi
Voltage: 13.2 / 14.0 Volts

7.16 Engine belt routing diagram

7.17 Spare parts list and wiring diagrams

The following information can be found on the reference CD supplied with this
chassis:

 Spare part information

 Low voltage and line voltage systems including the following information:
o Pictorial representation of circuit logic for all electrical components and
wiring
o Fuse identification and locations
o Circuit identification
o Connector pin identification
o Zone location of electrical components
o Safety interlocks
o Alternator – battery power distribution circuits
o Input / Output assignment sheets or equivalent circuit logic
implemented in multiplexing systems

79
7.18 Maintenance and repair record
This section is provided for your convenience to track maintenance and repairs
performed on the apparatus. Copy this sheet as needed.

Date Problem Repair Technician

80
7.19 Cleaning and washing

NOTICE
Use of incorrect cleaning agents can cause damage to the surfaces of the
vehicle.

Aggressive cleaning agents can cause surfaces, coatings and composite parts to
decompose. Abrasive particles cause scratches.

 Do not use aggressive cleaning agents that contain benzol, acetone or

softeners.
 Do not use household soaps or detergents to clean the vehicle.
 Do not use solvents to clean the dashboard, panels, or displays.
 Do not use dry towels to remove soiling from the vehicle’s paintwork.
 Do not polish with crude oil or grease.

NOTICE
Damage to surfaces due to spraying with pressure washers.

Pressurized water from pressure washers can cause severe damage to surfaces
and paintwork.

 Do not direct pressure washers or pressurized water at the vehicles surface.

 Do not spray U-joints with pressure cleaners.

Wash the vehicle frequently with cold or lukewarm water. Do not use household
soap or detergent. The use of a reliable car shampoo will assist in dissolving traffic
film.

After the surplus of dirt has been washed off, clean the body with a sponge and
plenty of water. At the same time it is advisable to wash the windshield wiper
blades by using clean water. Incorporate wheel wells into washing procedure. Pay
attention to open drain holes. Rinse off the vehicle with cold water, then rub down
with a clean chamois leather.

Twice a year, after washing and leathering the vehicle thoroughly, apply an
approved body polish to impart a brilliant, water resistant and lasting finish to the
paintwork.

Any tar or asphalt spots on the body may be removed with a tar cleaner and the
use of a soft towel.

Use moist towels to clean the control panels and dash gauges. Excess water can
damage electric components. Do not use solvents.

Keep the chrome plated parts clean and free from rust. These parts should be
cleaned periodically with chrome cleaner.

Upholstery can be suitably cleaned with interior cleaner. Never use polishes, oils,
petroleum, or a dry cleaning fluid.

81
8 Troubleshooting
8.1 General troubleshooting
Symptom Probable Cause Corrective Action
Engine does not crank. No cranking voltage. Check if the battery main switch is
on.

Check if the terminals on the

batteries are clean and tight.

Check battery voltage, if necessary

charge or replace batteries.

Transmission is not in neutral. Shift transmission into neutral.

Electrical system defect. Obtain workshop assistance.

Engine cranks but does not No fuel. Top up fuel and prime fuel system.
start.
If the fuel gauge indicates sufficient
fuel, obtain workshop assistance.

Engine or fuel system defect. Obtain workshop assistance/contact

Rosenbauer customer service.
No gear engages in Engine idle speed too high. Reduce idle speed.
transmission.
Electronic Control Unit (ECU) Switch off ignition and start vehicle
in failure mode. again.

If symptom remains, obtain workshop

assistance.
Vehicle does not move. Parking brake activated. Deactivate parking brake.

No gear selected. Select appropriate gear.

Transmission defect. Obtain workshop assistance

Transmission oil level too low. Fill transmission oil to full level.

If oil level is correct, obtain workshop

assistance.
Steering characteristics vary Low power steering fluid level. Stop the vehicle and fill power
noticeably from normal steering fluid.
operation.
If fluid level is correct, obtain
workshop assistance.
Inconsistent service brake Brake system defect. Stop the vehicle and obtain workshop
operation. assistance.

82
 Symptom Probable Cause Corrective Action
Parking brake does not hold Brake system defect. Do not drive the vehicle, chock the
vehicle. wheels and obtain workshop
assistance.

8.2 Cab tilt troubleshooting

Symptom Probable Cause Corrective Action
Electric/hydraulic pump does The master power disconnect Turn the master power disconnect
not energize when pendant switch may not be in the on switch to the on position.
buttons are depressed. position.
Electric/hydraulic pump does The parking brake may not be Engage the parking brake.
not energize when pendant engaged.
buttons are depressed.
Electric/hydraulic pump does Cab tilt pendant not plugged in Check that the cab tilt pendant
not energize when pendant or not plugged in properly. control is properly connected to the
buttons are depressed. cab tilt pendant outlet (usually located
near the pump panel).
Electric/hydraulic pump does Electric/hydraulic pump fuse Check electric/hydraulic pump fuse,
not energize when pendant may be blown. replace if necessary. See below for
buttons are depressed. fuse location.

8.2.1 Cab tilt pump fuse location

83
8.3 Fuse panel diagram

84
9 Environmental protection
9.1 Disposal of hazardous substances
The used parts and materials resulting from repairs and operation must be
disposed of in an environmentally responsible way.

Disposal of used oil, coolant and fuel

Used oil, coolant and fuel are among substances hazardous to waters. Ensure
correct disposal of used oil and fuels.
► Don’t pour used oil, coolant or fuel on the ground, in waters, or into sewer or
sewage systems.
► Collect and dispose of used oil accordingly.
► Obey the locally valid environmental regulations.

Disposal of desiccant inserts, filter cartridges, filter boxes and filter

inserts
Filter inserts, filter boxes and filter cartridges (oil filter, desiccant inserts of the air
dryer) are hazardous waste and have to be disposed of professionally.
► Obey the locally valid regulations.

Disposal of batteries
Batteries are contaminant laden and they have to be disposed of professionally.
► Never dispose of used batteries in the garbage!
► Obey the locally valid regulations.

Disposal of sacrificial anodes

Sacrificial anodes have to be changed regularly, therefor the used sacrificial
anodes have to be disposed of professionally.
► Dispose of sacrificial anodes with nonferrous metal.
► Obey the locally valid regulations.

Disposal of metal, rubber and plastic parts

Environmental pollution develops from false disposal of metal, rubber and plastic
parts.
► Obey the locally valid regulations.

Disposal of adhesive, paint and coating material

Environmental pollution develops from incorrect disposal of adhesive, paint and
coating material.
► Obey the locally valid regulations.

Disposal of control units

Control units are hazardous waste and have to be disposed of professionally.
► Obey the locally valid regulations.

85
10 Technical data
10.1 Chassis specifications
Vehicle Identification Number (VIN) 54F2CB51XEWM10809
Year of production 2014
Cab model number 8607851
Cab serial number 70946LG431
Engine make and model Cummins ISL 9 L
Engine horse power rating 450 HP
Transmission make and model Allison 3000 EVS
Front suspension Hendrickson 9 Leaf Spring (20,000 lb)
Steer Axle Meritor MFS Beam (20,000 lb)
Rear suspension Reyco 79KB Spring Conv. (27,000 lb)
Rear axle Meritor RS-25-160 (27,000 lb)
Gross vehicle weight rating (GVWR) 47,000 lb
Front Tires (2) 385-65R 22.5 Goodyear G296 MSA J
Front Wheels (2) Alcoa Dura-Bright 22.5 x 12.25 Alum
Rear Tires (4) 12R 22.5 Goodyear G622 H
Rear Wheels (4) Alcoa Dura-Bright 22.5 x 8.25 Alum
Vehicle top speed 70 MPH
Alternator Leece-Neville 320 Amp

10.2 Engine specifications

Advertised Horsepower 270-450 hp 201-336 kW

Peak Torque 800-1250 lb-ft 1084-1695 N•m
Governed Speed 2100-2200 rpm 2100-2200 rpm
Clutch Engagement Torque 500-550 lb-ft 678-746 N•m
Number of Cylinders 6 6
System Weight 1,912 lb 867 kg
Engine (Dry) 1,695 lb 769 kg
Aftertreatment System* 217 lb 98 kg

*Increase over standard muffler and does not include chassis OEM-supplied
components.

For further technical data please refer to your engine manufacturer’s manual.

86
10.3 Warranty and registration
10.3.1 Warranty procedures

Warranty Registration

1. The Rosenbauer America warranty registration form must be completed and

returned to Rosenbauer America upon receipt of the new vehicle. If the warranty
registration form is not returned, the date on the invoice for the vehicle will apply
as the “in service date”.
2. All other warranty registration forms must be completed and mailed to each
respective manufacturer.

Warranty Pre-Authorization Procedure

1. Authorization is required prior to any repairs or parts replacement.

2. Customer / Dealer must contact Rosenbauer America to obtain authorization.
3. Information required for authorization:
a. Vehicle identification number (the last 6 digits)
b. In service date
c. Mileage
d. Description of problem or failure.
4. Rosenbauer America will determine if the problem is covered under warranty. In
some cases this may require telephone troubleshooting with our service personal
to help determine the problem source.
5. If it is determined to fall under another manufacturer’s warranty (such as non
Rosenbauer components) Rosenbauer America will contact that manufacturer in
order to obtain authorization to proceed. In some cases, the manufacturer will
need to speak directly with the customer / dealer to aid in identifying the problem.
6. Rosenbauer America must authorize the repair facility at which the warranty
repairs are to be performed. If another manufacturer’s warranty applies, that
manufacturer must authorize the repair facility.
7. Rosenbauer America must be provided with an estimate of the costs associated
with the repair, prior to any work being performed, at which time an approval will
be given.

Warranty Claim Procedure

1. Contact your Rosenbauer Service Department or Rosenbauer Certified Dealer.

2. Rosenbauer Service Response System (SRS) to be populated with warranty claim
information will notify the service department immediately.
3. Rosenbauer service department will make contact with customer or dealer
immediately.

Warranty Invoicing Procedure

Upon completion of the approved repair, contact Rosenbauer America to obtain a

warranty authorization number. This number is to be included on the invoice to
Rosenbauer America.

87
10.3.2 Cab and chassis limited warranty

Rosenbauer Motors, LLC hereby warrants each new fire & rescue vehicle to be
free from defects in material and workmanship for a warranty period of two (2)
years or 36,000 miles starting on the date the vehicle is delivered to original
purchaser.

Under this warranty Rosenbauer Motors, LLC agrees to furnish any item or items
to replace those that have been found to defective in material or workmanship
where there is no indication of abuse, neglect, unusual or other than normal
service providing that such item or items are, at the option of Rosenbauer Motors,
LLC, made available for our inspection at our request, returned to our factory or
other location designated by us with transportation prepaid within thirty days after
the date of failure or within one year from the date of delivery of the apparatus to
the original purchaser, whichever occurs first, and inspection indicates the failure
was attributed to defective material or workmanship. Written authorization for
repair or item replacement must be sought from Rosenbauer Motors, LLC
customer service prior to the repair or item replacement occurring.

This warranty shall not apply to or cover:

 Normal maintenance services or adjustments, including but not limited too;

filters, screens, lubricants, light bulbs, belts, hoses, wiper blades and other
incidentals.
 Any item that has been repaired, replaced or altered by a facility not approved
in advance by Rosenbauer Motors, LLC, or in a manner which, at Rosenbauer
Motors, LLC discretion, may adversely affect the safe operation or durability of
the vehicle or item.
 Special, incidental or consequential damages including, but not limited to, loss
of time, inconvenience, loss of use, lost profits or transportation fees or
charges to or from any facility.
 Any malfunction resulting from misuse, negligence, alteration, accident or lack
of operational knowledge, lack off normal maintenance or adjustments,
exposure to corrosive agents, fire, severe environmental conditions or acts of
God.
 Items which are manufactured by a party other than Rosenbauer Motors, LLC
and which are separately warranted by that party, including but not limited to
engine, transmission, driveline, axles and water pumps.

This warranty is in lieu of all other warranties, expressed or implied, and all other
obligations or liabilities on our part. We neither assume nor authorize any person
to assume for us any liability or make any alteration to this warranty in connection
with the sale of our apparatus unless expressly given in writing by Rosenbauer
Motors, LLC, 5190 260th St. Wyoming, MN 55092.

NOTE: Surety bond, if required, will cover the standard one year warranty period
only and will not cover any extended warranties allowed by seller or other
component warranties.

10.3.3 Cab paint warranty

Rosenbauer Motors, LLC hereby warrants the paint on the cab and body of each
new fire & rescue vehicle to be free from blistering, peeling, corrosion or any other

88
 adhesion defect caused by defective manufacturing methods or paint material
selection for a warranty period of ten (10) years starting on the date the vehicle is
delivered to original purchaser.

Under this warranty Rosenbauer Motors, LLC agrees to repair or refinish any
painted surface that has been found to have an adhesion defect caused by
defective manufacturing methods or paint material selection where there is no
indication of abuse, neglect, unusual or other than normal service providing that
such item or items are, at the option of Rosenbauer Motors, LLC, made available
for our inspection at our request, returned to our factory or other location
designated by us with transportation prepaid within thirty days after the date of
failure or within five years from the date of delivery of the apparatus to the original
purchaser, whichever occurs first, and inspection indicates the failure was
attributed to an adhesion defect caused by defective manufacturing methods or
paint material selection. Written authorization for repair or item replacement must
be sought from Rosenbauer Motors, LLC customer service prior to the repair or
item replacement occurring.

This warranty shall not apply to or cover:

 Normal maintenance services or adjustments, including but not limited to;

filters, screens, lubricants, light bulbs, belts, hoses, wiper blades and other
incidentals.
 Any item that has been repaired, replaced or altered by a facility not approved
in advance by Rosenbauer Motors, LLC, or in a manner which, at Rosenbauer
Motors, LLC discretion, may adversely affect the safe operation or durability of
the vehicle or item.
 Special, incidental or consequential damages including, but not limited to, loss
of time, inconvenience, loss of use, lost profits or transportation fees or
charges to or from any facility.
 Any malfunction resulting from misuse, negligence, alteration, accident or lack
of operational knowledge, lack of normal or required maintenance or
adjustments, exposure to chemicals, UV fade, fire, severe environmental
conditions or acts of God.
 Painted Items which are manufactured by a party other than Rosenbauer
Motors, LLC and which are separately warranted by that party, including but
not limited to engine, transmission, driveline, axles and water pumps, etc.

This warranty is in lieu of all other warranties, expressed or implied, and all other
obligations or liabilities on our part. We neither assume nor authorize any person
to assume for us any liability or make any alteration to this warranty in connection
with the sale of our apparatus unless expressly given in writing by Rosenbauer
Motors, LLC, 5190 260th St. Wyoming, MN 55092.

NOTE: Surety bond, if required, will cover standard one year warranty period only
and will not cover any extended warranties allowed by seller or other component
manufacturers.

10.3.4 Cab structural warranty

Rosenbauer Motors, LLC hereby warrants the cab of each new fire & rescue
vehicle to be free from defects in material or workmanship for a warranty period of

89
 10 years or 100,000 miles starting on the date the vehicle is delivered to original
purchaser.

Under this warranty Rosenbauer Motors, LLC agrees to furnish any item or items
to replace those that have been found to defective in material or workmanship
where there is no indication of abuse, neglect, unusual or other than normal
service providing that such item or items are, at the option of Rosenbauer Motors,
LLC, made available for our inspection at our request, returned to our factory or
other location designated by us with transportation prepaid within thirty days after
the date of failure or within ten years from the date of delivery of the apparatus to
the original purchaser, whichever occurs first, and inspection indicates the failure
was attributed to defective material or workmanship Written authorization for repair
or item replacement must be sought from Rosenbauer Motors, LLC customer
service prior to the repair or item replacement occurring.

This warranty shall not apply to or cover:

 Normal maintenance services or adjustments, including but not limited to;

filters, screens, lubricants, light bulbs, belts, hoses, wiper blades and other
incidentals.
 Any item that has been repaired, replaced or altered by a facility not approved
in advance by Rosenbauer Motors, LLC, or in a manner which, at Rosenbauer
Motors, LLC discretion, may adversely affect the safe operation or durability of
the vehicle or item.
 Special, incidental or consequential damages including, but not limited to, loss
of time, inconvenience, loss of use, lost profits or transportation fees or
charges to or from any facility.
 Any malfunction resulting from misuse, negligence, alteration, accident or lack
of operational knowledge, lack of normal or required maintenance or
adjustments, exposure to corrosive agents, fire, severe environmental
conditions or acts of God.
 Items which are manufactured by a party other than Rosenbauer Motors, LLC
and which are separately warranted by that party, including but not limited to
engine, transmission, driveline, axles and water pumps.

This warranty is in lieu of all other warranties, expressed or implied, and all other
obligations or liabilities on our part. We neither assume nor authorize any person
to assume for us any liability or make any alteration to this warranty in connection
with the sale of our apparatus unless expressly given in writing by Rosenbauer
Motors, LLC, 5190 260th St. Wyoming, MN 55092.

NOTE: Surety bond, if required, will cover standard one year warranty period only
and will not cover any extended warranties allowed by seller or other component
manufacturers.

10.3.5 Front and rear axle warranty

The front and rear axles shall be warranted by Meritor® for two (2) years with
unlimited miles under the general service application.

10.3.6 Chassis frame warranty

Rosenbauer Motors, LLC hereby warrants to the original purchaser of a

90
 Rosenbauer Motors, LLC chassis that the frame and cross members be free of
defects in material and workmanship for the lifetime of the frontline service of the
chassis.

Rosenbauer Motors, LLC’s obligation under this warranty is to furnish any item or
items of such frame or frame members, to replace those that have been found to
defective in material or workmanship where there is no indication of abuse,
neglect, unusual or other than normal service providing that such item or items
are, at the option of Rosenbauer Motors, LLC, made available for our inspection at
our request, returned to our factory or other location designated by us with
transportation prepaid within thirty days after the date of failure and inspection
indicates the failure was attributed to defective material or workmanship. Written
authorization for repair or item replacement must be sought from Rosenbauer
Motors, LLC customer service prior to the repair or item replacement occurring.

This warranty shall not apply to or cover:

 Normal maintenance services or adjustments, including but not limited to;

filters, screens, lubricants, light bulbs, belts, hoses, wiper blades and other
incidentals.
 Any item that has been repaired, replaced or altered by a facility not approved
in advance by Rosenbauer Motors, LLC, or in a manner which, at Rosenbauer
Motors, LLC discretion, may adversely affect the safe operation or durability of
the vehicle or item.
 Special, incidental or consequential damages including, but not limited to, loss
of time, inconvenience, loss of use, lost profits or transportation fees or
charges to or from any facility.
 Any malfunction resulting from misuse, negligence, alteration, accident or lack
of operational knowledge, lack of normal or required maintenance or
adjustments, exposure to chemicals, fire, severe environmental conditions,
corrosion or acts of God.
 Any cutting, welding, splicing, drilling or other alteration of frame rails or
flanges without express written permission from Rosenbauer Motors, LLC or if
this vehicle is involved in an accident, shall render this warranty null and void.

This warranty is in lieu of all other warranties, expressed or implied, and all other
obligations or liabilities on our part. We neither assume nor authorize any person
to assume for us any liability or make any alteration to this warranty in connection
with the sale of our apparatus unless expressly given in writing by Rosenbauer
Motors, LLC, 5190 260th St. Wyoming, MN 55092.

NOTE: Surety bond, if required, will cover standard one year warranty period only
and will not cover any extended warranties allowed by seller or other component
manufacturers.

10.3.7 Cummins engine warranty

Products Warranted
This Warranty applies to new diesel Engines sold by Cummins and delivered to
the first user on or after April 1, 2007, that are used in fire apparatus truck and
crash truck* applications Worldwide.

91
 Base Engine Warranty
The Base Engine Warranty covers any failures of the Engine which result, under
normal use and service, from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the sale of the Engine by
Cummins and ends five years or 100,000 miles (160,935 kilometers), whichever
occurs first, after the date of delivery of the Engine to the first user.

Engine aftertreatment components included in the Cummins Critical Parts List

(CPL) and marked with a Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission Warranty section.

These Warranties are made to all Owners in the chain of distribution and
Coverage continues to all subsequent Owners until the end of the periods of
Coverage.

Cummins Responsibilities
Cummins will pay for all parts and labor needed to repair the damage to the
Engine resulting from a Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze, filter elements, belts, hoses and
other maintenance items that are not reusable due to the Warrantable Failure.

Cummins will pay for reasonable labor costs for Engine removal and reinstallation
when necessary to repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a vehicle disabled by a Warrantable
Failure to the nearest authorized repair location. In lieu of the towing expense,
Cummins will pay reasonable costs for mechanics to travel to and from the
location of the vehicle, including meals, mileage and lodging when the repair is
performed at the site of the failure.

Owner Responsibilities
Owner is responsible for the operation and maintenance of the Engine as specified
in Cummins Operation and Maintenance Manuals. Owner is also responsible for
providing proof that all recommended maintenance has been performed.

Before the expiration of the applicable Warranty, Owner must notify a Cummins
distributor, authorized dealer or other repair location approved by Cummins of any
Warrantable Failure and make the Engine available for repair by such facility.
Except for Engines disabled by a Warrantable Failure, Owner must also deliver the
Engine to the repair facility.

Service locations are listed on the Cummins Worldwide Service Locator at

cummins.com.

92
Owner is responsible for the cost of lubricating oil, antifreeze, filter elements and
other maintenance items provided during Warranty repairs unless such items are
not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses, meals, lodging and similar

costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for ‘‘downtime’’ expenses, cargo
damage, fines, all applicable taxes, all business costs and other losses resulting
from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars) deductible per each service visit
under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine
Warranty.

Limitations
Engines with an emissions certification listed below must be operated using only
diesel fuel having no more than the corresponding maximum sulfur content.
Failure to use the specified fuel (see also Cummins Fuel Bulletin #3379001) can
damage the Engine and aftertreatment system within a short period of time. This
damage could cause the Engine to become inoperable and failures attributable to
the use of incorrect fuels will be denied Warranty Coverage.

Maximum sulfur levels by emissions certification level as listed on the engine’s

dataplate are:
EPA 2007 max. 15 parts per million
EPA 2010 max. 15 parts per million
EPA Tier 4 Interim / Final max. 15 parts per million
EU Stage IIIB 2011 max. 15 parts per million
Euro 4/5 max. 50 parts per million

Cummins is not responsible for failures or damage resulting from what Cummins
determines to be abuse or neglect, including, but not limited to: operation without
adequate coolants or lubricants; overfueling; overspeeding; lack of maintenance of
lubricating, cooling or intake systems; improper storage, starting, warm-up, run-in
or shutdown practices; unauthorized modifications of the Engine.

Any unauthorized modifications to the aftertreatment could negatively effect

emissions certification and void Warranty.

Cummins is also not responsible for failures caused by incorrect oil, fuel or diesel
exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

This Warranty does not apply to accessories supplied by Cummins which bear the
name of another company. Such non-warranted accessories include, but are not
limited to: alternators, starters, fans, air conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps, power steering pumps, fan

93
 drives and air compressors. Cummins branded alternators and starters are
covered for the first two years from the date of delivery of the Engine to the first
user, or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the
duration of the Coverage or 100,000 miles (160,935 kilometers) or 7,000 hours
from the date of delivery of the Engine to the first user, whichever of the three
occurs first. Before a claim for excessive oil consumption will be considered,
Owner must submit adequate documentation to show that consumption exceeds
Cummins published standards.

Failures of belts and hoses supplied by Cummins are not covered beyond the first
year from the date of delivery of the Engine to the first user or the duration of the
Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new Cummins parts, Cummins
approved rebuilt parts or repaired parts. Cummins is not responsible for failures
resulting from the use of parts not approved by Cummins.

A new Cummins or Cummins approved rebuilt part used to repair a Warrantable

Failure assumes the identity of the part it replaced and is entitled to the remaining
Coverage hereunder.

Cummins Inc. reserves the right to interrogate Electronic Control Module (ECM)
data for purposes of failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

THIS WARRANTY AND THE EMISSION WARRANTY SET FORTH

HEREINAFTER ARE THE SOLE WARRANTIES MADE BY CUMMINS IN
REGARD TO THESE ENGINES. CUMMINS MAKES NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, OR OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.

This Warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.

Emissions Warranty

Products Warranted
This Emission Warranty applies to new Engines marketed by Cummins that are
used in the United States** in vehicles designed for transporting persons or
property on a street or highway. This Warranty applies to Engines delivered to the
first user on or after September 1, 1992.

94
Coverage
Cummins warrants to the first user and each subsequent purchaser that the
Engine is designed, built and equipped so as to conform at the time of sale by
Cummins with all U.S. federal emission regulations applicable at the time of
manufacture and that it is free from defects in material or factory workmanship
which would cause it not to meet these regulations within the longer of the
following periods: (A) Five years or 100,000 miles (160,935 kilometers) of
operation, whichever occurs first, as measured from the date of delivery of the
Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is registered in the state of California,
a separate California Emission Warranty also applies.

Limitations
Engines with an emissions certification listed below must be operated using only
diesel fuel having no more than the corresponding maximum sulfur content.

Failure to use the specified fuel (see also Cummins Fuel Bulletin #3379001) can
damage the Engine and aftertreatment system within a short period of time. This
damage could cause the Engine to become inoperable and failures attributable to
the use of incorrect fuels will be denied Warranty Coverage.

Maximum sulfur levels by emissions certification level as listed on the Engine’s

dataplate are:
EPA 2007 max. 15 parts per million
EPA 2010 max. 15 parts per million
EPA Tier 4 Interim / Final max. 15 parts per million
EU Stage IIIB 2011 max. 15 parts per million
Euro 4/5 max. 50 parts per million

Failures, other than those resulting from defects in material or factory

workmanship, are not covered by this Warranty.

Cummins is not responsible for failures or damage resulting from what Cummins
determines to be abuse or neglect, including, but not limited to: operation without
adequate coolants or lubricants; overfueling; overspeeding; lack of maintenance of
lubricating, cooling or intake systems; improper storage, starting, warm-up, run-in
or shutdown practices; unauthorized modifications of the Engine.

Any unauthorized modifications to the aftertreatment could negatively effect

emissions certification and void Warranty.

Cummins is also not responsible for failures caused by incorrect oil, fuel or diesel
exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs, ‘‘downtime’’ expenses, cargo

damage, fines, all applicable taxes, all business costs or other losses resulting
from a Warrantable Failure.

95
 CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.

* Airport operated crash trucks and fire department operated trucks employed to
respond to fires, hazardous material releases, rescue and other emergency-type
situations.

** United States includes American Samoa, the Commonwealth of Northern

Mariana Islands, Guam, Puerto Rico and the U.S. Virgin Islands.

10.3.8 Allison transmission warranty

Allison Transmission will provide for repairs or replacement, at its option, during
the warranty period of each new Allison transmission listed below that is installed
in an On-Highway Truck other than Automotive Fire Apparatus in accordance with
the following terms, conditions, and limitations.

WHAT IS COVERED

 WARRANTY APPLIES – This warranty is for new Allison transmission models

listed below installed in an On-Highway Truck other than Line Haul and
Automotive Fire Apparatus and is provided to the original and any subsequent
owner(s) of the vehicle during the warranty period.
 REPAIRS COVERED – The warranty covers repairs or replacement, at Allison
Transmission’s option, to correct any transmission malfunction resulting from
defects in material or workmanship occurring during the warranty period.
Needed repairs or replacements will be performed using the method Allison
Transmission determines most appropriate under the circumstances.
 TOWING – Towing is covered to the nearest Allison Transmission Distributor
or authorized Dealer only when necessary to prevent further damage to your
transmission.
 PAYMENT TERMS – Warranty repairs including parts and labor, will be
covered per the schedule shown in the chart contained in section
“APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT
SCHEDULE.”
 OBTAINING REPAIRS – To obtain warranty repairs, take the vehicle to any
Allison Transmission Distributor or authorized Dealer within a reasonable
amount of time and request the needed repairs. A reasonable amount of time
must be allowed for the Distributor or Dealer to perform necessary repairs.
 TRANSMISSION REMOVAL AND REINSTALLATION – Labor costs for the
removal and re-installation of the transmission, when necessary to make a
warranty repair, are covered by this warranty.
 WARRANTY PERIOD – The warranty period for all coverages shall begin on
the date the transmission is delivered to the first retail purchaser, with the
following exception:
 Demonstration Service – A transmission in a new truck or bus
may be demonstrated to a total of 5000 miles (8000 kilometers). If
the vehicle is within this limit when sold to a retail purchaser, the
warranty start date is the date of purchase. Normal warranty
services are applicable to the demonstrating Dealer. Should the
truck or bus be sold to a retail purchaser after these limits are
reached, the warranty period will begin on the date the vehicle was

96
 first placed in demonstration service and the purchaser will be
entitled to the remaining warranty.
The warranty period for all coverages shall end at the expiration of the coverage
set forth below:

WHAT IS NOT COVERED

 DAMAGE DUE TO ACCIDENT, MISUSE, or ALTERATION

 Defects and damage caused as the result of any of the following are not
covered:
 Flood, collision, fire, theft, freezing, vandalism, riot, explosion, or
objects striking the vehicle;
 Misuse of the vehicle;
 Installation into unapproved applications and installations;
 Alterations or modification of the transmission or the vehicle, and
 Damage resulting from improper storage (refer to long-term storage
procedure outlined in the applicable Allison Service Manual)
 Anything other than defects in Allison Transmission material or
workmanship
NOTE: This warranty is void on transmissions used in vehicles currently or
previously titled as salvage, scrapped, junked, or totaled.

 CHASSIS, BODY, and COMPONENTS – The chassis and body company

(assemblers) and other component and equipment manufacturers are solely
responsible for warranties on the chassis, body, component(s), and equipment
they provide. Any transmission repair caused by an alteration(s) made to the
Allison transmission or the vehicle which allows the transmission to be installed
or operated outside of the limits defined in the appropriate Allison Installation
Guideline is solely the responsibility of the entity making the alteration(s).
 DAMAGE CAUSED by LACK of MAINTENACE or by the USE of
TRANSMISSION FLUIDS NOT RECOMMENDED in the OPERATOR’S
MANUAL – Defects and damage caused by any of the following are not
covered:
 Failure to follow the recommendations of the maintenance schedule
intervals applicable to the transmission;
 Failure to use transmission fluids or maintain transmission fluid levels
recommended in the Operator’s Manual.

97
  MAINTENANCE – Normal maintenance (such as replacement of filters,
screens, and transmission fluid) is not covered and is the owner’s
responsibility.
 REPAIRS by UNAUTHORIZED DEALERS – Defects and damage caused by
a service outlet that is not an authorized Allison Transmission Distributor or
Dealer are not covered.
 USE of OTHER THAN GENUINE ALLISON TRANSMISSION PARTS –
Defects and damage caused by the use of parts that are not genuine Allison
Transmission parts are not covered.
 EXTRA EXPENSES – Economic loss and extra expenses are not covered.
Examples include but are not limited to: loss of vehicle use; inconvenience;
storage; payment for loss of time or pay; vehicle rental expense; lodging;
meals; or other travel costs.
 “DENIED PARTY” OWNERSHIP – Warranty repair parts and labor costs are
not reimbursed to any participating or non-participating OEMs, dealers or
distributors who perform warranty work for, or on behalf of, end users identified
by the United States as being a “denied party” or who are citizens of
sanctioned or embargoed countries as defined by the U.S. Department of
Treasury Office of Foreign Assets Control. Furthermore, warranty
reimbursements are not guaranteed if the reimbursement would be contrary to
any United States export control laws or regulations as defined by the U.S.
Department of Commerce, the U.S. Department of State, or the U.S.
Department of Treasury.
OTHER TERMS APPLICABLE TO CONSUMERS AS DEFINED by the MAGNUSON-
MOSS WARRANTY ACT

This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.

Allison Transmission does not authorize any person to create for it any other
obligation or liability in connection with these transmissions. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE APPLICABLE TO THESE TRANSMISSIONS IS LIMITED IN
DURATION TO THE DURATION OF THIS WRITTEN WARRANTY.
PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE
EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED
WARRANTY. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED
TO, LOST WAGES OR VEHICLE RENTAL EXPENSES) RESULTING FROM
BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.**

** Some states do not allow limitations on how long an implied warranty will last or
the exclusion or limitation of incidental or consequential damages, so the above
limitations of exclusions may not apply to you.
OTHER TERMS APPLICABLE TO OTHER END-USERS

THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THE ALLISON

TRANSMISION MODELS LISTED ABOVE AND IS EXPRESSLY IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANT ABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. ALLISON TRANSMISSION DOES NOT AUTHORIZE ANY PERSON
TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN
CONNECTION WITH SUCH TRANSMISSIONS. ALLISON TRANSMISSION

98
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED
WARRANTY.

QUESTIONS

If you have any questions regarding this warranty or the performance of warranty
obligations, you may contact any Allison Transmission Distributor or Dealer or
write to:

Allison Transmission
General Motors Corporation
P.O. Box 894
Indianapolis, IN 46206-0894
Attention: Warranty Administration 462-470-PF9
Form SE0617EN (200606)

99