Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 61 views

    Single-Stage BJT Amplifiers and BJT High-Frequency Model: Asst. Prof. Dr. Montree Siripruchyanun

    Uploaded by

    Mohd Anwar
    1. The document discusses three basic configurations for single-stage BJT amplifiers: common-emitter, common-base, and common-collector. It examines the small-signal operation and characteristics of each configuration. 2. Common-emitter amplifiers are analyzed using the hybrid-π model. Adding emitter degeneration increases input resistance but lowers voltage gain. 3. Common-base amplifiers have little dependence on β, gain depends on Rs, and it is commonly used as a current buffer. 4. Common-collector amplifiers, also called emitter followers, have a gain close to unity and are used to connect a high-resistance source to a low-res

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Single-Stage BJT Amplifiers and BJT High-Frequency Model: Asst. Prof. Dr. Montree Siripruchyanun

    Uploaded by

    Mohd Anwar
    61 views5 pages
    1. The document discusses three basic configurations for single-stage BJT amplifiers: common-emitter, common-base, and common-collector. It examines the small-signal operation and characteristics of each configuration. 2. Common-emitter amplifiers are analyzed using the hybrid-π model. Adding emitter degeneration increases input resistance but lowers voltage gain. 3. Common-base amplifiers have little dependence on β, gain depends on Rs, and it is commonly used as a current buffer. 4. Common-collector amplifiers, also called emitter followers, have a gain close to unity and are used to connect a high-resistance source to a low-res

    Original Title

    BJT amp2

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. The document discusses three basic configurations for single-stage BJT amplifiers: common-emitter, common-base, and common-collector. It examines the small-signal operation and characteristics of each configuration. 2. Common-emitter amplifiers are analyzed using the hybrid-π model. Adding emitter degeneration increases input resistance but lowers voltage gain. 3. Common-base amplifiers have little dependence on β, gain depends on Rs, and it is commonly used as a current buffer. 4. Common-collector amplifiers, also called emitter followers, have a gain close to unity and are used to connect a high-resistance source to a low-res

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    61 views5 pages

    Single-Stage BJT Amplifiers and BJT High-Frequency Model: Asst. Prof. Dr. Montree Siripruchyanun

    Uploaded by

    Mohd Anwar
    1. The document discusses three basic configurations for single-stage BJT amplifiers: common-emitter, common-base, and common-collector. It examines the small-signal operation and characteristics of each configuration. 2. Common-emitter amplifiers are analyzed using the hybrid-π model. Adding emitter degeneration increases input resistance but lowers voltage gain. 3. Common-base amplifiers have little dependence on β, gain depends on Rs, and it is commonly used as a current buffer. 4. Common-collector amplifiers, also called emitter followers, have a gain close to unity and are used to connect a high-resistance source to a low-res

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    1

    Single-Stage BJT Amplifiers and BJT High-Frequency Model


    Asst. Prof. MONTREE SIRIPRUCHYANUN, D. Eng. Dept. of Teacher Training in Electrical Engineering, Faculty of Technical Education King Mongkuts Institute of Technology North Bangkok http://www.te.kmitnb.ac.th/msn mts@kmitnb.ac.th
    1

    Single-Stage BJT Amplifier Configurations


    There are three basic configurations for single-stage BJT amplifiers: Common-Emitter (Common-Source) Common-Base (Common-Gate) Common-Collector (Common-Drain) Lets look at these amplifier configurations and their small-signal operation

    224510 Advanced communication circuit design

    Asst. Prof. Dr. MONTREE SIRIPRUCHYANUN

    Common-Emitter Amplifier
    First, assume Re = 0 (this is not re, but an explicit resistor) The BJT is biased with a current source (with high output impedance) and a capacitor connects the emitter to ground. Cap provides an AC short at the emitter for small time-varying signals but is an open circuit for DC signals Can redraw the circuit with an equivalent circuit that replaces the BJT with its hybrid- model Rs B C

    gmv vs v r r RC vo

    224510 Advanced communication circuit design

    CE Amp with Emitter Degeneration


    Now, assume Re 0. First, find Ri voltage applied to the base is across re and Re

    base current is

    and lets find Ri

    this tells us adding Re increases the input resistance

    Can design the desired Ri by setting Re


    224510 Advanced communication circuit design 4

    Asst. Prof. Dr. MONTREE SIRIPRUCHYANUN

    To determine the voltage gain, first find the gain from the base to the collector (ignore ro b/c it complicates the analysis considerably)

    NOTE: Voltage gain between base and collector is equal to ratio of total resistance in the collector to the total resistance in the emitter. To find the total gain,

    Characteristics with Re : gain is lower, but also less dependent on input resistance is higher allows higher input signal voltage
    224510 Advanced communication circuit design 5

    Common-Base Amplifier
    Ground the base and drive the input signal into the emitter through a coupling capacitor (only passes ac signals)

    Model the small signal approximation with a T-model current source is an AC open and CC is an AC short
    224510 Advanced communication circuit design 6

    Asst. Prof. Dr. MONTREE SIRIPRUCHYANUN

    First, we can see that

    To find the gain, solve for vo

    The output impedance is just CB amp characteristics: voltage gain has little dependence on gain depends critically on Rs is non-inverting most commonly used as a unity-gain current amplifier or current buffer and not as a voltage amplifier: accepts an input signal current with low input resistance and delivers a nearly equal current with high output impedance most significant advantage is its excellent frequency response (which we will see later)
    224510 Advanced communication circuit design 7

    Common-Collector Amplifier (Emitter Follower)


    The last basic configuration is to tie the collector to a fixed voltage, drive an input signal into the base and observe the output at the emitter

    Also called an emitter follower since the emitter follows the input signal Used for connecting a source with a large Rs to a load with low resistance

    224510 Advanced communication circuit design

    Asst. Prof. Dr. MONTREE SIRIPRUCHYANUN

    Redraw the circuit to have ro in parallel with RL now, find Ri when re << RL << ro notice the amplifier has large input resistance Find the gain with two voltage dividers

    gain is less than unity, but close (to unity) since is large and re is small
    224510 Advanced communication circuit design 9

    High-Frequency BJT Model


    rb B C r v C gmv r C

    In BJTs, the PN junctions (EBJ and CBJ) also have capacitances associated with them C is the reverse-biased CB junction

    Where mjc is between 0.2 and 0.5, V0 is between 0.5V and 1V

    C represents the capacitance of the forward-biased EBJ which exhibits both the junction cap and diffusion cap

    Where Cje is the junction cap and F is the base-transit time

    At high frequencies, the base resistance can also an important role in device operation

    224510 Advanced communication circuit design

    10

    Asst. Prof. Dr. MONTREE SIRIPRUCHYANUN

    You might also like