Lab 07
Lab 07
Lab 07
EE321 – Lab 7
Bipolar Junction Transistors, Part I
In this lab we will investigate how a bipolar junction transistor (BJT) can be used to amplify
signals.
1. First, use your multi meter to measure the base-emitter and base-collector junctions of your
transistor (Figure 1 and 2). When you put your meter in “Diode” mode, the meter will
indicate the voltage for 1 mA current through a forward-biased diode, and will indicate 0
if the diode is reversed biased. Test this on a diode then on a 2N3904 transistor. Record
your readings. This is a useful way to check for bad transistors. This is better than using
the Ohm-Meter for measuring the forward and reverse resistances of the junctions, as the
measuring voltage and current are not known.
C VCC = 10V
1K
B VO
C
VS 2N3904
E B
B 10K E
C E
Figure 1. Figure 2. Figure 3.
2. The basic principle of a BJT is that the base-emitter voltage vBE controls the collector current
iC when the transistor is biased in its ‘active’ mode (b-e junction forward biased, c-b junction
reverse biased).
• Construct the circuit (Figure 3). Lay your circuit out neatly, using the bus lines for VCC
and ground.
• Connect a sine wave to vS and display vBE and vC in on your oscilloscope.
• Adjust input sine wave, vS (the DC bias (offset) and amplitude) so that vBE varies from
about 0.0 to about 0.73 volts. Be sure to measure vBE at the base of the transistor.
Make vBE large enough so that vO goes from 10 V to 0 V.
• Both vBE and vO will look like clipped sine waves. Where do they clip?
3. Note that vC = VCC − iC RC . Use this to determine where the transistor is in cutoff (iC = 0)
and where it is in saturation (vCE < 0.7). (In between, the transistor is in its active region.)
• Display vC vs. vBE using the x-y mode. Using this curve, plot iC vs. vBE . This curve
should look like Figure 4.12 of Sedra and Smith. Note the three regions of the plot.
• For what value of vBE does the transistor start to turn ‘on’ ? (Collector current start to
flow?) Does this make sense?
• When vBE is too large, the collector current will drop vC below vB , thus forward-biasing
the collector-base junction and driving the transistor into saturation. For what values
of vBE and iC does this occur?
1
EE 321 Lab 7 Fall 2002
4. The transfer characteristic is linear if vBE is restricted to small changes about a bias point,
as in Figure 4.24 of Sedra and Smith.
• Reduce the p-p signal amplitude and change the offset until only a small part of the
transfer curve going from about 3.5 mA to 6.5 mA is left (fiddle with the signal generator
until the output is a sine wave that goes between 6.5 V and 3.5 V. Start with an input
amplitude of 0.1 V and offset of 0.5 V). Now you should find that vC changes by 3 V
p-p about the bias point at IC = 5 mA.
• Sketch the operating range on the plot of part 3 above.
• In the time domain, display vBE and vC on your scope. What is the voltage gain vc /vbe
for the small signals? (Be sure to measure the ‘input’ vbe after the 10 kΩ resistor.)
• How does the gain compare with theoretical value found in the prelab?
• How could the gain be made larger? (There are two ways.)
5. Increase vBE and note the distorted nature of vC . Increase vBE further until the output just
”clips” on top and bottom. (Readjust the DC level so that the clipping is symmetrical).
6. The output voltage can be linearized over its entire range by using the input signal to con-
trol the base current rather than the base voltage. This is because the collector current is
proportional to the base current, i.e. iC = βiB . We will show this in the following way:
First we will bias the transistor in its active state by supplying a current to the base through
RB from +VCC (see Figure 4). This provides a DC base current IB = (VCC − 0.7V)/RB ,
which gets amplified by the transistor to give a DC collector current IC = βIB . Because
β varies from transistor to transistor you will have to select the value of RB to obtain the
desired IC .
1K
RB 1K
RB
VO VO
C C
2N3904 VS 2N3904
B E 10K 1uF B E
Figure 4. Figure 5.
2
EE 321 Lab 7 Fall 2002
7. Now add a signal component to the base current through a coupling capacitor, as shown in
Figure 5, which does not affect the DC bias. Note that the input voltage has been converted
to a current by resistor RS .
• Increase vs until the output clips, and back off until the clipping just stops.
• What is the maximum output voltage swing
• Is the output linearly related to the input. vs ? (Adjust the scope — position, sensitivity,
invert — until the input and output line up. If they line up and the output is a bigger
copy of the input they are linearly related.)
• What is the voltage gain, vout /vs ?
Pre-Lab
2. Find the gain for the amplifier in Figure 3. The gain can be determined from these equations:
vout = −ic RC , ic = gm vbe , and gm = IC /VT , with IC = 5 mA.