TBD62304A series

TOSHIBA BiCD Integrated Circuit Silicon Monolithic

TBD62304APG, TBD62304AFNG, TBD62304AFWG

7-ch low active sink type DMOS transistor array

TBD62304A series are DMOS transistor arrays with 7 circuits. Please be

careful about thermal conditions during use. TBD62304APG

Features
• Built-in 7 circuits
• High voltage : VOUT = 50 V (max)
• High current : IOUT = 500 mA/ch (max)
• Input voltage (output on) : -20 V to VCC-3.5 V DIP16-P-300-2.54A
• Input voltage (output off) : VCC-0.4 V to VCC
• Package : PG type DIP16-P-300-2.54A TBD62304AFNG
FNG type SSOP16-P-225-0.65B
FWG type P-SOP16-0410-1.27-002

SSOP16-P-225-0.65B
Pin Assignment (top view)
TBD62304AFWG
O1 O2 O3 O4 O5 O6 O7 VCC

I1 I2 I3 I4 I5 I6 I7 GND P-SOP16-0410-1.27-002
Weight
DIP16-P-300-2.54A :1.13 g (typ.)
SSOP16-P-225-0.65B :0.07 g (typ.)
P-SOP16-0410-1.27-002 :0.15 g (typ.)

Pin connection may be omitted partially or simplified for explanatory purpose.

©2017 Toshiba Corporation 1 2017-03-24

 TBD62304A series

Pin Descriptions

Pin No. Pin name Function

1 I1 Input pin
2 I2 Input pin
3 I3 Input pin
4 I4 Input pin
5 I5 Input pin
6 I6 Input pin
7 I7 Input pin
8 GND Ground pin
9 VCC Power supply pin
10 O7 Output pin
11 O6 Output pin
12 O5 Output pin
13 O4 Output pin
14 O3 Output pin
15 O2 Output pin
16 O1 Output pin

Basic Circuit

VCC

OUTPUT
INPUT

Basic circuit may be omitted partially or simplified for explanatory purpose.

2 2017-03-24
 TBD62304A series
Absolute Maximum Ratings (Ta = 25°C)

Characteristics Symbol Rating Unit

Power supply voltage VCC −0.5 to 6.0 V

Output voltage VOUT 50 V
Output current (per ch) IOUT 500 mA
Input voltage VIN −22 to VCC+0.5 (Note4) V
PG (Note1) 1.47
Power FNG (Note2) PD 0.78 W
dissipation
FWG (Note3) 1.25
Operating temperature Topr −40 to 85 °C
Storage temperature Tstg −55 to 150 °C
Note1: Standalone. When Ta exceeds 25 °C, it is necessary to do the derating with 11.8 mW/°C.
Note2: On PCB (size: 50 mm × 50 mm × 1.6 mm, Cu area: 40 %, single-side glass epoxy). When Ta exceeds 25 °C, it is
necessary to do the derating with 6.24 mW/°C.
Note3: On PCB (compliant with JEDEC 2s2p). When Ta exceeds 25 °C, it is necessary to do the derating with 10
mW/°C.
Note4: Do not exceed 6 V

Operating Ranges (Ta = −40 to 85°C, unless otherwise specified.)

Characteristics Symbol Test conditions Min Typ. Max Unit

Power supply voltage VCC ― 4.5 5.0 5.5 V

Output voltage VOUT ― ― ― 50 V
1 circuit ON, Ta = 25 °C 0 ― 400
tpw = 25 ms Duty = 10 % 0 ― 400
PG (Note1) 7 circuits ON
Ta = 85 °C Duty = 50 % 0 ― 190
Tj = 120 °C
1 circuit ON, Ta = 25 °C 0 ― 400
Output current tpw = 25 ms Duty = 10 % 0 ― 300
FNG (Note2) IOUT 7 circuits ON mA
(per ch) Ta = 85 °C Duty = 50 % 0 ― 130
Tj = 120 °C
1 circuit ON, Ta = 25 °C 0 ― 400
tpw = 25 ms Duty = 10 % 0 ― 390
FWG (Note3) 7 circuits ON
Ta = 85 °C Duty = 50 % 0 ― 170
Tj = 120 °C

Input voltage (Output on) VIN (ON) IOUT = 100 mA or more, VOUT = 2 V -20 ― VCC-3.5 V

Input voltage (Output off) VIN (OFF) IOUT = 100 μA or less, VOUT = 2 V VCC-0.4 ― VCC V
Note1: Stand alone
Note2: On PCB (size: 50 mm × 50 mm × 1.6 mm, Cu area: 40 %, single-side glass epoxy).
Note3: On PCB (compliant with JEDEC 2s2p)

3 2017-03-24
 TBD62304A series
Electrical Characteristics (Ta = 25°C, unless otherwise specified.)
Test
Characteristics Symbol Test conditions Min Typ. Max Unit
Circuit
VOUT = 50 V, Ta = 85 °C
Output leakage current Ileak 1 ― ― 1.0 μA
VIN = VCC = 5.5 V
IOUT = 350 mA 0.525 1.14
―
VCC = 5.0 V, VIN = 0 V (1.5) (3.25)
Output voltage VDS IOUT = 200 mA, 0.3 0.65 V
2 ―
(Output ON-resistance) (RON) VCC = 5.0 V, VIN = 0 V (1.5) (3.25) (Ω)
IOUT = 100 mA 0.15 0.325
―
VCC = 5.0 V, VIN = 0 V (1.5) (3.25)
VCC = 5.5 V, VIN = 0 V ― -10 -100
IIN(ON) 3 μA
Input current VCC = 5.5 V, VIN = -20 V ― -100 -200
IIN(OFF) 4 VCC = VIN = 5.5 V ― ― 1.0 μA
ICC(ON) 3 VCC = 5.5 V, VIN = 0 V ― 70 200 μA
Consumption current (per ch)
ICC(OFF) 4 VCC = 5.5 V, VIN = VCC ― ― 1.0 μA
Turn-on delay tON VCC = 5.0 V, VOUT = 50 V ― 0.6 ―
5 RL = 125 Ω μs
Turn-off delay tOFF CL = 15 pF ― 0.6 ―

4 2017-03-24
 TBD62304A series

Test Circuit

1. Ileak 2. VDS (RON)

VCC VCC

INPUT OUTPUT INPUT OUTPUT

Ileak IOUT
VCC VIN VOUT VCC VIN VDS
GND GND

RON = VDS / IOUT

3. IIN (ON), ICC (ON) 4. IIN (OFF), ICC (OFF)

VCC VCC

INPUT OUTPUT INPUT OUTPUT

ICC(ON) IIN(ON) ICC(OFF) IIN(OFF)
VCC VIN VCC VIN
GND GND

Test circuits may be omitted partially or simplified for explanatory purpose.

5 2017-03-24
 TBD62304A series

5. tON, tOFF

(Note 1)
(Note 2)

tf tr

Note1: Pulse width 50 μs, Duty cycle 10 %

Output impedance 50 Ω, tr ≤ 5 ns, tf ≤ 10 ns, VIH = 5.0 V
Note2: CL includes capacitance of the probe and the test board.

Test circuits and timing charts may be omitted partially or simplified for explanatory purpose.

Precautions for Using

This IC does not incorporate built-in protection circuits for excess current or over voltage.
Therefore, if the short-circuit between adjacent pins or between outputs, the short-to-power or ground fault has occurred,
the current or voltage beyond the absolute maximum rating is impressed, and IC may be destroyed. When designing,
please consider enough in power supply line, output line, and GND line.
In addition, so as not to continue to flow a current that exceeds the absolute maximum rating of the IC, please insert the
appropriate fuse in the power supply line.

6 2017-03-24
 TBD62304A series
Package Dimensions
DIP16-P-300-2.54A Unit: mm

Weight: 1.13 g (typ.)

SSOP16-P-225-0.65B Unit: mm

Weight: 0.07 g (typ.)

7 2017-03-24
 TBD62304A series

P-SOP16-0410-1.27-002 Unit: mm

Weight: 0.15 g (typ.)

8 2017-03-24
 TBD62304A series
Notes on Contents
1. Pin Connection
Pin connection may be simplified for explanatory purpose.
2. Equivalent Circuit
Equivalent circuit may be simplified for explanatory purpose.
3. Test Circuit
Test circuit may be simplified for explanatory purpose.
4. Timing Chart
Timing charts may be simplified for explanatory purposes.

IC Usage Considerations
Notes on handling of ICs
(1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a
moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause device breakdown, damage or
deterioration, and may result in injury by explosion or combustion.

(2) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of
power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute
maximum rating, and exceeding the rating(s) may cause device breakdown, damage or deterioration, and may result
in injury by explosion or combustion. In addition, do not use any device inserted in the wrong orientation or incorrectly
to which current is applied even just once.

(3) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in the case of
overcurrent and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute
maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or
load, causing a large current to continuously flow and the breakdown can lead to smoke or ignition. To minimize the
effects of the flow of a large current in the case of breakdown, appropriate settings, such as fuse capacity, fusing time
and insertion circuit location, are required.

(4) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to
prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the
negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or
ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the
protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition.

(5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such
as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as from input
or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a
speaker with low input withstand voltage, overcurrent or IC failure may cause smoke or ignition. (The overcurrent may
cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL)
connection-type IC that inputs output DC voltage to a speaker directly.

Points to remember on handling of ICs

Heat Radiation Design
When using an IC with large current flow such as power amp, regulator or driver, design the device so that heat is
appropriately radiated, in order not to exceed the specified junction temperature (Tj) at any time or under any condition.
These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life,
deterioration of IC characteristics or IC breakdown. In addition, when designing the device, take into consideration the
effect of IC heat radiation with peripheral components.
Back-EMF
When a motor rotates in the reverse direction, stops or slows abruptly, current flows back to the motor’s power supply
owing to the effect of back-EMF. If the current sink capability of the power supply is small, the device’s motor power
supply and output pins might be exposed to conditions beyond the absolute maximum ratings. To avoid this problem, take
the effect of back-EMF into consideration in system design.

9 2017-03-24
 TBD62304A series
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in
this document, and related hardware, software and systems (collectively "Product") without notice.

• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's
written permission, reproduction is permissible only if reproduction is without alteration/omission.

• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury
or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or
incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant
TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product
and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the
application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or
applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b)
evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms,
sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and
applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.

• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA
sales representative.

• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.

• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.

• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any
intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.

• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.

• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology
products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws
and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration
Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all
applicable export laws and regulations.

• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.

10 2017-03-24
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Toshiba:
TBD62304AFNG,EL