Features: 0.5Mhz, Low Supply Voltage, Low Input Current Bimos Operational Amplifier
Features: 0.5Mhz, Low Supply Voltage, Low Input Current Bimos Operational Amplifier
CA3420 FN1320
0.5MHz, Low Supply Voltage, Low Input Current BiMOS Operational Amplifier Rev 9.00
Oct 4, 2005
Pinout
CA3420 (PDIP)
TOP VIEW
V- 4 5 OFFSET NULL
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Short circuit may be applied to ground or to either supply.
2. JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Typical Values Intended Only for Design Guidance, VSUPPLY = 10V, TA = 25°C
PARAMETER SYMBOL TEST CONDITIONS TYP UNITS
Input Resistance RI 150 T
Input Capacitance CI 4.9 pF
Output Resistance RO 300
Equivalent Input Noise Voltage eN f = 1kHz RS = 100 62 nV/Hz
f = 10kHz 38 nV/Hz
Short-Circuit Current Source IOM+ 2.6 mA
To Opposite Supply Sink IOM- 2.4 mA
Gain Bandwidth Product fT 0.5 MHz
Slew Rate SR 0.5 V/s
Transient Response Rise Time tR RL = 2k, CL = 100pF 0.7 s
Overshoot OS 15 %
Current from Terminal 8 To V- I8+ 20 A
To V+ I8- 2 mA
Electrical Specifications For Equipment Design, At VSUPPLY = 1V, TA = 25°C, Unless Otherwise Specified
TEST
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Input Offset Voltage |VIO| - 5 10 mV
Input Offset Current (Note 3) |IIO| - 0.01 4 pA
Input Current (Note 3) |II| - 1 5 pA
Large Signal Voltage Gain AOL RL = 10k 10 100 - kV/V
80 100 - dB
Common Mode Rejection Ratio CMRR - 560 1800 V/V
55 65 - dB
Common Mode Input Voltage Range VlCR+ 0.2 0.5 - V
VlCR- - -1.3 - V
Power Supply Rejection Ratio PSRR VIO/V - 100 1000 V/V
60 80 - dB
Max Output Voltage VOM+ RL = 0.90 0.95 - V
VOM- -0.85 -0.91 - V
Supply Current I+ - 350 650 A
Device Dissipation PD - 0.7 1.1 mW
Input Offset Voltage Temperature Drift VlO/T - 4 - V/°C
NOTE:
3. The maximum limit represents the levels obtainable on high speed automatic test equipment. Typical values are obtained under laboratory conditions.
Electrical Specifications For Equipment Design, at VSUPPLY = 10V, TA = 25°C, Unless Otherwise Specified
TEST
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Input Offset Voltage |VIO| - 5 10 mV
Input Offset Current (Note 4) |IIO| - 0.03 4 pA
Input Current (Note 4) |II| - 0.05 5 pA
Large Signal Voltage Gain AOL RL = 10k 10 100 - kV/V
80 100 - dB
Common Mode Rejection Ratio CMRR - 100 320 V/V
70 80 - dB
Common Mode Input Voltage Range VlCR+ 8.5 9.3 - V
VlCR- -10 -10.3 - V
Power Supply Rejection Ratio PSRR VIO/V - 32 320 V/V
70 90 - dB
Max Output Voltage VOM+ RL = 9.7 9.9 - V
VOM- -9.7 -9.85 - V
Supply Current I+ - 450 1000 A
Device Dissipation PD - 9 14 mW
Input Offset Voltage Temperature Drift VlO/T - 4 - V/°C
NOTE:
4. The maximum limit represents the levels obtainable on high speed automatic test equipment. Typical values are obtained under laboratory conditions.
Typical Applications
10G 10pF
+1.5V
Picoammeter Circuit
500-0-500
2 - 7
The exceptionally low input current (typically 0.2pA) makes 1M 10M
A
the CA3420 highly suited for use in a picoammeter circuit. CA3420 6 M
With only a single 10G resistor, this circuit covers the range 3 + 4 50pA
1.5k
from 1.5pA. Higher current ranges are possible with suitable 5
BATTERY
1 1.5k, 1%
switching techniques and current scaling resistors. Input RETURNS 15pA
10k 1k
transient protection is provided by the 1M resistor in series
430, 1%
with the input. Higher current ranges require that this resistor 5pA
be reduced. The 10M resistor connected to pin 2 of the
-1.5V 150, 1%
CA3420 decouples the potentially high input capacitance 1.5pA
often associated with lower current circuits and reduces the
tendency for the circuit to oscillate under these conditions. 11k 68
1%
High Input Resistance Voltmeter
FIGURE 1. PICOAMMETER CIRCUIT
Advantage is taken of the high input impedance of the CA3420
in a high input resistance DC voltmeter. Only two 1.5V “AA” +1.5V
type penlite batteries power this exceedingly high-input 500-0-500
3 + 7
A
resistance (>1,000,000M) DC voltmeter. Full-scale deflection 22M 10M
CA3420 6 M
is 500mV, 150mV, and 15mV. Higher voltage ranges are 100pF
2 - 4 500mV 1.5k
easily added with external input voltage attenuator networks. 5
1 BATTERY
The meter is placed in series with the gain network, thus RETURNS 1.5k, 1%
10k 150mV
eliminating the meter temperature coefficient error term. 1k
68
1.1k 1%
TA = 25°C V- = 0V
0.8 RL = 100k
V+ = 2V
0.6
V+ = 5V
-0.4 VICR-
-0.6
VICR+
-0.8
1000
-1.0 0.01 0.1 1 10
0 1 5 10 15
LOAD (SOURCING) CURRENT (mA)
SUPPLY VOLTAGE (V)
FIGURE 3. OUTPUT VOLTAGE SWING AND COMMON MODE FIGURE 4. OUTPUT VOLTAGE vs LOAD SOURCING CURRENT
INPUT VOLTAGE RANGE vs SUPPLY VOLTAGE
1000 1000
TA = 25°C
V+ = 0V VS = 10V
VS = 5V
VS = 1V
VOLTAGE, Q17 (mV)
100
V- = -20V
V- = -10V
100 V- = -5V
V- = -2V
10
10 1
0.01 0.1 1 10
101 102 103 104 105 106
LOAD (SINKING) CURRENT (mA) FREQUENCY (Hz)
FIGURE 5. OUTPUT VOLTAGE vs LOAD SINKING CURRENT FIGURE 6. INPUT NOISE VOLTAGE vs FREQUENCY
TA = 25°C
OPEN LOOP PHASE (DEGREES)
VS = 5V
100 RL = 10k
CL = 0pF
0
OPEN LOOP VOLTAGE GAIN (dB)
80 -45
-90
60 -135
-180
40
20
0
1 101 102 103 104 105 106
FREQUENCY (Hz)
N
E8.3 (JEDEC MS-001-BA ISSUE D)
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX INCHES MILLIMETERS
AREA 1 2 3 N/2
SYMBOL MIN MAX MIN MAX NOTES
-B-
A - 0.210 - 5.33 4
-A-
D E A1 0.015 - 0.39 - 4
BASE A2 0.115 0.195 2.93 4.95 -
PLANE A2
-C- A
SEATING
B 0.014 0.022 0.356 0.558 -
PLANE L C B1 0.045 0.070 1.15 1.77 8, 10
L
D1 A1 eA C 0.008 0.014 0.204 0.355 -
D1
B1 e D 0.355 0.400 9.01 10.16 5
eC C
B
eB D1 0.005 - 0.13 - 5
0.010 (0.25) M C A B S
E 0.300 0.325 7.62 8.25 6
NOTES: E1 0.240 0.280 6.10 7.11 5
1. Controlling Dimensions: INCH. In case of conflict between
e 0.100 BSC 2.54 BSC -
English and Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982. eA 0.300 BSC 7.62 BSC 6
3. Symbols are defined in the “MO Series Symbol List” in Section eB - 0.430 - 10.92 7
2.2 of Publication No. 95. L 0.115 0.150 2.93 3.81 4
4. Dimensions A, A1 and L are measured with the package seated
N 8 8 9
in JEDEC seating plane gauge GS-3.
5. D, D1, and E1 dimensions do not include mold flash or protru- Rev. 0 12/93
sions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be per-
pendicular to datum -C- .
7. eB and eC are measured at the lead tips with the leads uncon-
strained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).