®

ICL7611, ICL7612

Data Sheet July 21, 2004 FN2919.7

1.4MHz, Low Power CMOS Operational Features

Amplifiers • Wide Operating Voltage Range . . . . . . . . . . . ±1V to ±8V
The ICL761X series is a family of CMOS operational • High Input Impedance . . . . . . . . . . . . . . . . . . . . . . 1012Ω
amplifiers. These devices provide the designer with high
• Programmable Power Consumption . . . . . Low as 20µW
performance operation at low supply voltages and selectable
quiescent currents, and are an ideal design tool when ultra • Input Current Lower Than BIFETs . . . . . . . . . . . 1pA (Typ)
low input current and low power dissipation are desired. • Output Voltage Swing . . . . . . . . . . . . . . . . . . . V+ and V-
The basic amplifier will operate at supply voltages ranging • Input Common Mode Voltage Range Greater Than Supply
from ±1V to ±8V, and may be operated from a single Rails (ICL7612)
Lithium cell.
• Pb-Free Plus Anneal Available (RoHS Compliant)
A unique quiescent current programming pin allows setting
of standby current to 1mA, 100µA, or 10µA, with no external Applications
components. This results in power consumption as low as
• Portable Instruments
20µW. The output swing ranges to within a few millivolts of
the supply voltages. • Telephone Headsets

Of particular significance is the extremely low (1pA) input • Hearing Aid/Microphone Amplifiers
current, input noise current of 0.01pA/√Hz, and 1012Ω input • Meter Amplifiers
impedance. These features optimize performance in very
• Medical Instruments
high source impedance applications.
• High Impedance Buffers
The inputs are internally protected. Outputs are fully
protected against short circuits to ground or to either supply.

AC performance is excellent, with a slew rate of 1.6V/µs, and

unity gain bandwidth of 1MHz at IQ = 1mA.

Because of the low power dissipation, junction temperature

rise and drift are quite low. Applications utilizing these
features may include stable instruments, extended life
designs, or high density packages.

Pinouts
ICL7611, ICL7612
(PDIP, SOIC)
TOP VIEW

BAL 1 8 IQ SET

-IN 2 - 7 V+
+
+IN 3 6 OUT

V- 4 5 BAL

1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2004, 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
 ICL7611, ICL7612

Ordering Information
TEMP.
PART RANGE PKG.
NUMBER (°C) PACKAGE DWG. #

ICL7611DCBA 0 to 70 8 Ld SOIC - D Grade M8.15

ICL7611DCBAZ 0 to 70 8 Ld SOIC - D Grade M8.15

(Note) (Pb-free)

ICL7611DCBA-T 0 to 70 8 Ld SOIC - D Grade M8.15

Tape and Reel

ICL7611DCBAZ-T 0 to 70 8 Ld SOIC - D Grade M8.15

(Note) Tape and Reel (Pb-free)

ICL7611DCPA 0 to 70 8 Ld PDIP - D Grade E8.3

ICL7611DCPAZ 0 to 70 8 Ld PDIP - D Grade* E8.3

(Note) (Pb-free)

ICL7612BCPA 0 to 70 8 Ld PDIP - B Grade E8.3

ICL7612DCBA 0 to 70 8 Ld SOIC - D Grade M8.15

ICL7612DCBAZ 0 to 70 8 Ld SOIC - D Grade M8.15

(Note) (Pb-free)

ICL7612DCBA-T 0 to 70 8 Ld SOIC - D Grade M8.15

Tape and Reel

ICL7612DCBAZ-T 0 to 70 8 Ld SOIC - D Grade M8.15

(Note) Tape and Reel (Pb-free)

ICL7612DCPA 0 to 70 8 Ld PDIP - D Grade E8.3

*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.

NOTE: Intersil Pb-free plus anneal products employ special Pb-free

material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.

2 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Absolute Maximum Ratings Thermal Information

Supply Voltage V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V Thermal Resistance (Typical, Note 3) θJA (°C/W)
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.3 to V+ +0.3V PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Differential Input Voltage (Note 1) . . . . . . . . [(V+ +0.3) - (V- -0.3)]V SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Duration of Output Short Circuit (Note 2). . . . . . . . . . . . . . Unlimited Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Operating Conditions Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
Temperature Range
ICL761XC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:
1. Long term offset voltage stability will be degraded if large input differential voltages are applied for long periods of time.
2. The outputs may be shorted to ground or to either supply, for VSUPPLY ≤10V. Care must be taken to insure that the dissipation rating is not
exceeded.
3. θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications VSUPPLY = ±5V, Unless Otherwise Specified

ICL7611B, ICL7612B ICL7611D, ICL7612D
TEST
PARAMETER SYMBOL CONDITIONS TEMP (°C) MIN TYP MAX MIN TYP MAX UNITS
Input Offset Voltage VOS RS ≤ 100kΩ 25 - - 5 - - 15 mV
Full - - 7 - - 20 mV
Temperature ∆VOS/∆T RS ≤ 100kΩ - - 15 - - 25 - µV/°C
Coefficient of VOS
Input Offset Current IOS 25 - 0.5 30 - 0.5 30 pA
Full - - 300 - - 300 pA
Input Bias Current IBIAS 25 - 1.0 50 - 1.0 50 pA
Full - - 400 - - 400 pA
Common Mode VCMR IQ = 10µA 25 ±4.4 - - ±4.4 - - V
Voltage Range
IQ = 100µA 25 ±4.2 - - ±4.2 - - V
(Except ICL7612)
IQ = 1mA 25 ±3.7 - - ±3.7 - - V
Extended Common VCMR IQ = 10µA 25 ±5.3 - - ±5.3 - - V
Mode Voltage Range
IQ = 100µA 25 +5.3, -5.1 - - +5.3, -5.1 - - V
(ICL7612 Only)
IQ = 1mA 25 +5.3, -4.5 - - +5.3, -4.5 - - V
Output Voltage Swing VOUT IQ = 10µA, RL = 1MΩ 25 ±4.9 - - ±4.9 - - V
Full ±4.8 - - ±4.8 - - V
IQ = 100µA, RL = 100kΩ 25 ±4.9 - - ±4.9 - - V
Full ±4.8 - - ±4.8 - - V
IQ = 1mA, RL = 10kΩ 25 ±4.5 - - ±4.5 - - V
Full ±4.3 - - ±4.3 - - V
Large Signal Voltage AVOL VO = ±4.0V, RL = 1MΩ, 25 80 104 - 80 104 - dB
Gain IQ = 10µA
Full 75 - - 75 - - dB
VO = ±4.0V, RL = 100kΩ, 25 80 102 - 80 102 - dB
IQ = 100µA
Full 75 - - 75 - - dB
VO = ±4.0V, RL = 10kΩ, 25 76 83 - 76 83 - dB
IQ = 1mA
Full 72 - - 72 - - dB

3 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Electrical Specifications VSUPPLY = ±5V, Unless Otherwise Specified (Continued)

ICL7611B, ICL7612B ICL7611D, ICL7612D
TEST
PARAMETER SYMBOL CONDITIONS TEMP (°C) MIN TYP MAX MIN TYP MAX UNITS
Unity Gain Bandwidth GBW IQ = 10µA 25 - 0.044 - - 0.044 - MHz
IQ = 100µA 25 - 0.48 - - 0.48 - MHz
IQ = 1mA 25 - 1.4 - - 1.4 - MHz
Input Resistance RIN 25 - 1012 - - 1012 - Ω
Common Mode CMRR RS ≤ 100kΩ, IQ = 10µA 25 70 96 - 70 96 - dB
Rejection Ratio
RS ≤ 100kΩ, IQ = 100µA 25 70 91 - 70 91 - dB
RS ≤ 100kΩ, IQ = 1mA 25 60 87 - 60 87 - dB
Power Supply PSRR RS ≤ 100kΩ, IQ = 10µA 25 80 94 - 80 94 - dB
Rejection Ratio
RS ≤ 100kΩ, IQ = 100µA 25 80 86 - 80 86 - dB
(VSUPPLY = ±8V to
±2V) RS ≤ 100kΩ, IQ = 1mA 25 70 77 - 70 77 - dB
Input Referred Noise eN RS = 100Ω, f = 1kHz 25 - 100 - - 100 - nV/√Hz
Voltage
Input Referred Noise iN RS = 100Ω, f = 1kHz 25 - 0.01 - - 0.01 - pA/√Hz
Current
Supply Current ISUPPLY IQ SET = +5V, Low Bias 25 - 0.01 0.02 - 0.01 0.02 mA
(No Signal, No Load)
IQ SET = 0V, 25 - 0.1 0.25 - 0.1 0.25 mA
Medium Bias
IQ SET = -5V, High Bias 25 - 1.0 2.5 - 1.0 2.5 mA
Channel Separation VO1/VO2 AV = 100 25 - 120 - - 120 - dB
Slew Rate SR IQ = 10µA, RL = 1MΩ 25 - 0.016 - - 0.016 - V/µs
(AV = 1, CL = 100pF,
IQ = 100µA, RL = 100kΩ 25 - 0.16 - - 0.16 - V/µs
VIN = 8VP-P)
IQ = 1mA, RL = 10kΩ 25 - 1.6 - - 1.6 - V/µs
Rise Time tr IQ = 10µA, RL = 1MΩ 25 - 20 - - 20 - µs
(VIN = 50mV,
IQ = 100µA, RL = 100kΩ 25 - 2 - - 2 - µs
CL = 100pF)
IQ = 1mA, RL = 10kΩ 25 - 0.9 - - 0.9 - µs
Overshoot Factor OS IQ = 10µA, RL = 1MΩ 25 - 5 - - 5 - %
(VIN = 50mV,
IQ = 100µA, RL = 100kΩ 25 - 10 - - 10 - %
CL = 100pF)
IQ = 1mA, RL = 10kΩ 25 - 40 - - 40 - %

Electrical Specifications VSUPPLY = ±1V, IQ = 10µA, Unless Otherwise Specified

ICL7611B, ICL7612B
TEST TEMP
PARAMETER SYMBOL CONDITIONS (°C) MIN TYP MAX UNITS
Input Offset Voltage VOS RS ≤ 100kΩ 25 - - 5 mV
Full - - 7 mV
Temperature Coefficient of VOS ∆VOS/∆T RS ≤ 100kΩ - - 15 - µV/°C
Input Offset Current IOS 25 - 0.5 30 pA
Full - - 300 pA
Input Bias Current IBIAS 25 - 1.0 50 pA
Full - - 500 pA
Common Mode Voltage Range VCMR 25 ±0.6 - - V
(Except ICL7612)
Extended Common Mode VCMR 25 +0.6 to - - V
Voltage Range (ICL7612 Only) -1.1

4 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Electrical Specifications VSUPPLY = ±1V, IQ = 10µA, Unless Otherwise Specified (Continued)

ICL7611B, ICL7612B
TEST TEMP
PARAMETER SYMBOL CONDITIONS (°C) MIN TYP MAX UNITS
Output Voltage Swing VOUT RL = 1MΩ 25 ±0.98 - - V
Full ±0.96 - - V
Large Signal Voltage Gain AVOL VO = ±0.1V, RL = 1MΩ 25 - 90 - dB
Full - 80 - dB
Unity Gain Bandwidth GBW 25 - 0.044 - MHz
Input Resistance RIN 25 - 1012 - Ω
Common Mode Rejection Ratio CMRR RS ≤ 100kΩ 25 - 80 - dB
Power Supply Rejection Ratio PSRR RS ≤ 100kΩ 25 - 80 - dB
Input Referred Noise Voltage eN RS = 100Ω, f = 1kHz 25 - 100 - nV/√Hz
Input Referred Noise Current iN RS = 100Ω, f = 1kHz 25 - 0.01 - pA/√Hz
Supply Current ISUPPLY No Signal, No Load 25 - 6 15 µA
Slew Rate SR AV = 1, CL = 100pF, 25 - 0.016 - V/µs
VIN = 0.2VP-P, RL = 1MΩ
Rise Time tr VIN = 50mV, CL = 100pF RL = 1MΩ 25 - 20 - µs
Overshoot Factor OS VIN = 50mV, CL = 100pF, RL = 1MΩ 25 - 5 - %

Schematic Diagram

IQ
INPUT STAGE SETTING STAGE OUTPUT STAGE

V+
900K
3K 3K
QP5
BAL QP6 QP7 6.3V
BAL
100K QP8
QP1 QP1
QP3 QP4

V+
QP9

+INPUT QN1 QN2

CFF = 9pF
OUTPUT
V- CC = 33pF
V+

-INPUT
QN7
QN4 QN6 QN9 QN10 QN11
V-
QN5
6.3V
QN3
QN8

V-

V+ IQ SET

5 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Application Information
Static Protection IQ = 10µA, nulling may not be possible with higher values
All devices are static protected by the use of input diodes. of VOS .
However, strong static fields should be avoided, as it is Frequency Compensation
possible for the strong fields to cause degraded diode
The ICL7611 and ICL7612 are internally compensated, and
junction characteristics, which may result in increased input
are stable for closed loop gains as low as unity with
leakage currents.
capacitive loads up to 100pF.
Latchup Avoidance
Extended Common Mode Input Range
Junction-isolated CMOS circuits employ configurations which
The ICL7612 incorporates additional processing which
produce a parasitic 4-layer (PNPN) structure. The 4-layer
allows the input CMVR to exceed each power supply rail by
structure has characteristics similar to an SCR, and under
0.1V for applications where VSUPP ≥ ±1.5V. For those
certain circumstances may be triggered into a low impedance
applications where VSUPP ≤ ±1.5V the input CMVR is limited
state resulting in excessive supply current. To avoid this
in the positive direction, but may exceed the negative supply
condition, no voltage greater than 0.3V beyond the supply
rail by 0.1V in the negative direction (e.g., for VSUPPLY = ±1V,
rails may be applied to any pin. In general, the op amp
the input CMVR would be +0.6V to -1.1V).
supplies must be established simultaneously with, or before
any input signals are applied. If this is not possible, the drive Operation At VSUPPLY = ±1V
circuits must limit input current flow to 2mA to prevent latchup. Operation at VSUPPLY = ±1V is guaranteed at IQ = 10µA for
Choosing the Proper IQ A and B grades only.
The ICL7611 and ICL7612 have a similar IQ set-up scheme, Output swings to within a few millivolts of the supply rails are
which allows the amplifier to be set to nominal quiescent achievable for RL ≥ 1MΩ. Guaranteed input CMVR is ±0.6V
currents of 10µA, 100µA or 1mA. These current settings minimum and typically +0.9V to -0.7V at VSUPPLY = ±1V. For
change only very slightly over the entire supply voltage applications where greater common mode range is
range. The ICL7611/12 have an external IQ control terminal, desirable, refer to the description of ICL7612 above.
permitting user selection of quiescent current. To set the IQ
connect the IQ terminal as follows: Typical Applications
IQ = 10µA - IQ pin to V+ The user is cautioned that, due to extremely high input
impedances, care must be exercised in layout, construction,
IQ = 100µA - IQ pin to ground. If this is not possible, any board cleanliness, and supply filtering to avoid hum and
voltage from V+ - 0.8 to V- +0.8 can be used. noise pickup.
IQ = 1mA - IQ pin to V- Note that in no case is IQ shown. The value of IQ must be
NOTE: The output current available is a function of the quiescent chosen by the designer with regard to frequency response
current setting. For maximum peak-to-peak output voltage swings and power dissipation.
into low impedance loads, IQ of 1mA should be selected.

Output Stage and Load Driving Considerations

VIN +
Each amplifiers’ quiescent current flows primarily in the ICL7612 VOUT
output stage. This is approximately 70% of the IQ settings. - RL ≥10K
This allows output swings to almost the supply rails for
output loads of 1MΩ, 100kΩ, and 10kΩ, using the output
stage in a highly linear class A mode. In this mode, FIGURE 1. SIMPLE FOLLOWER (NOTE 4)
crossover distortion is avoided and the voltage gain is
maximized. However, the output stage can also be operated
+5 +5
in Class AB for higher output currents. (See graphs under VIN -
Typical Operating Characteristics). During the transition from ICL7612 VOUT
Class A to Class B operation, the output transfer 100K + TO CMOS OR
LPTTL LOGIC
characteristic is non-linear and the voltage gain decreases.

Input Offset Nulling

1M
Offset nulling may be achieved by connecting a 25K pot
NOTE:
between the BAL terminals with the wiper connected to V+.
4. By using the ICL7612 in this application, the circuit will follow rail
At quiescent currents of 1mA and 100µA the nulling range to rail inputs.
provided is adequate for all VOS selections; however with
FIGURE 2. LEVEL DETECTOR (NOTE 4)

6 FN2919.7
July 21, 2004
 ICL7611, ICL7612

- 1M
1µF ICL7611 -
+ + ICL7611
+
- 1M

ICL7611 VOUT 1M
λ + V- V+
DUTY CYCLE
680kΩ

WAVEFORM GENERATOR

NOTE: Low leakage currents allow integration times up to several NOTE: Since the output range swings exactly from rail to rail, frequency
hours. and duty cycle are virtually independent of power supply variations.

FIGURE 3. PHOTOCURRENT INTEGRATOR FIGURE 4. PRECISE TRIANGLE/SQUARE WAVE

GENERATOR

1M +8V
VOH
0.5µF 10K 2.2M 20K
TO TA = 125°C
VIN SUCCEED- + V+
+ 10µF ING
20K INPUT
ICL7611 STAGE OUT
1.8K = 5% IQ
-
SCALE - V-
ADJUST VOL

- V+
ICL7611 -8V
COMMON
+

FIGURE 5. AVERAGING AC TO DC CONVERTER FOR A/D FIGURE 6. BURN-IN AND LIFE TEST CIRCUIT
CONVERTERS SUCH AS ICL7106, ICL7107,
ICL7109, ICL7116, ICL7117

VIN VOUT
BAL

+ BAL

25k

V+

FIGURE 7. VOS NULL CIRCUIT

7 FN2919.7
July 21, 2004
 ICL7611, ICL7612

0.2µF
0.2µF 0.2µF

30K 160K
+ 680K 100K 51K
ICL7611 +
- ICL7611
-
360K
INPUT 1M
0.1µF 0.2µF 0.1µF
OUTPUT

360K (NOTE 5) 1M
(NOTE 5)
NOTES:
5. Note that small capacitors (25pF to 50pF) may be needed for stability in some cases.
6. The low bias currents permit high resistance and low capacitance values to be used to achieve low frequency cutoff. fC = 10Hz, AVCL = 4,
Passband ripple = 0.1dB.

FIGURE 8. FIFTH ORDER CHEBYCHEV MULTIPLE FEEDBACK LOW PASS FILTER

Typical Performance Curves

10K 104
TA = 25°C V+ - V- = 10V
NO LOAD IQ = 1mA NO LOAD
NO SIGNAL NO SIGNAL
IQ = 1mA
SUPPLY CURRENT (µA)

SUPPLY CURRENT (µA)

1K 103

IQ = 100µA
100 102 IQ = 100µA

IIQQ == 10µA
1mA
IQ = 10µA
10 10

1 1
0 2 4 6 8 10 12 14 16 -50 -25 0 25 50 75 100 125
SUPPLY VOLTAGE (V) FREE-AIR TEMPERATURE (°C)

FIGURE 9. SUPPLY CURRENT PER AMPLIFIER vs SUPPLY FIGURE 10. SUPPLY CURRENT PER AMPLIFIER vs FREE-AIR
VOLTAGE TEMPERATURE

8 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Typical Performance Curves (Continued)

1000 1000
VSUPP = 10V

DIFFERENTIAL VOLTAGE GAIN (kV/V)

VS = ±5V
VOUT = 8V
INPUT BIAS CURRENT (pA)

RL = 1MΩ
100
IQ = 10µA
100
RL = 100kΩ
IQ = 100µA
10 RL = 10kΩ
IQ = 1mA

10
1.0

0.1 1
-50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125
FREE-AIR TEMPERATURE (°C) FREE-AIR TEMPERATURE (°C)

FIGURE 11. INPUT BIAS CURRENT vs TEMPERATURE FIGURE 12. LARGE SIGNAL DIFFERENTIAL VOLTAGE GAIN
vs FREE-AIR TEMPERATURE

107 105

COMMON MODE REJECTION RATIO (dB)

TA = 25°C VSUPP = 10V
DIFFERENTIAL VOLTAGE GAIN (V/V)

106 VSUPP = 15V 100

IQ = 10µA

105 95
IQ = 100µA
IQ = 100µA
PHASE SHIFT (DEGREES)

IQ = 1mA 0 90
104 IQ = 1mA

45 85
103
PHASE SHIFT
(IQ = 1mA)
90 80
102

135 75
10
IQ = 10µA
1 180 70
0.1 1.0 10 100 1K 10K 100K 1M -75 -50 -25 0 25 50 75 100 125
FREQUENCY (Hz) FREE-AIR TEMPERATURE (°C)

FIGURE 13. LARGE SIGNAL FREQUENCY RESPONSE FIGURE 14. COMMON MODE REJECTION RATIO vs FREE-AIR
TEMPERATURE
EQUIVALENT INPUT NOISE VOLTAGE (nV/√Hz)

100 600
SUPPLY VOLTAGE REJECTION RATIO (dB)

IQ = 1mA VSUPP = 10V TA = 25°C

95 3V ≤ VSUPP ≤ 16V
500

90 IQ = 100µA
400
85
IQ = 10µA
300
80

200
75

70 100

65 0
-75 -50 -25 0 25 50 75 100 125 10 100 1K 10K 100K
FREE-AIR TEMPERATURE (°C) FREQUENCY (Hz)

FIGURE 15. POWER SUPPLY REJECTION RATIO vs FREE-AIR FIGURE 16. EQUIVALENT INPUT NOISE VOLTAGE vs
TEMPERATURE FREQUENCY

9 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Typical Performance Curves (Continued)

16 16
TA = 25°C VSUPP = 10V

MAXIMUM OUTPUT VOLTAGE (VP-P)

MAXIMUM OUTPUT VOLTAGE (VP-P)

14 14 IQ = 1mA
IQ = 1mA
VSUPP
12 = ±8V IQ = 10µA 12
IQ = 100µA
10 10
TA = -55°C

8 8 TA = 25°C
VSUPP TA = 125°C
6 6
= ±5V

4 4

2 2
VSUPP
= ±2V
0 0
100 1K 10K 100K 1M 10M 10K 100K 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)

FIGURE 17. OUTPUT VOLTAGE vs FREQUENCY FIGURE 18. OUTPUT VOLTAGE vs FREQUENCY

16 12
TA = 25°C
MAXIMUM OUTPUT VOLTAGE (VP-P)
MAXIMUM OUTPUT VOLTAGE (VP-P)

RL = 100kΩ
14 10

12
8 RL = 10kΩ
RL = 100kΩ - 1MΩ
10
6
RL = 2kΩ
8 RL = 10kΩ

4
6
VSUPP = 10V
4 2 IQ = 1mA

0
2 4 6 8 10 12 14 16 -75 -50 -25 0 25 50 75 100 125
SUPPLY VOLTAGE (V) FREE-AIR TEMPERATURE (°C)

FIGURE 19. OUTPUT VOLTAGE vs SUPPLY VOLTAGE FIGURE 20. OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE

40 0.01
MAXIMUM OUTPUT SOURCE CURRENT (mA)

MAXIMUM OUTPUT SINK CURRENT (mA)

IQ = 1mA

30 IQ = 10µA
0.1

20
IQ = 100µA
1.0
10

IQ = 1mA
0 10
0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V)

FIGURE 21. OUTPUT SOURCE CURRENT vs SUPPLY VOLTAGE FIGURE 22. OUTPUT SINK CURRENT vs SUPPLY VOLTAGE

10 FN2919.7
July 21, 2004
 ICL7611, ICL7612

Typical Performance Curves (Continued)

16 8
TA = 25°C TA = 25°C, VSUPP = 10V
MAXIMUM OUTPUT VOLTAGE (VP-P)

14 V+ - V- = 10V

INPUT AND OUTPUT VOLTAGE (V)

6 RL = 10kΩ, CL = 100pF
IQ = 1mA
12
4
10
2
8
0 OUTPUT
6
-2
4 INPUT

2 -4

0 -6
0.1 1.0 10 100 0 2 4 6 8 10 12
LOAD RESISTANCE (kΩ) TIME (µs)

FIGURE 23. OUTPUT VOLTAGE vs LOAD RESISTANCE FIGURE 24. VOLTAGE FOLLOWER LARGE SIGNAL PULSE
RESPONSE (IQ = 1mA)

8 8
TA = 25°C, VSUPP = 10V TA = 25°C, VSUPP = 10V
INPUT AND OUTPUT VOLTAGE (V)

INPUT AND OUTPUT VOLTAGE (V)

6 RL = 100kΩ, CL = 100pF 6 RL = 1MΩ, CL = 100pF

4 4

2 2
OUTPUT OUTPUT
0 0
INPUT
-2 -2
INPUT
-4 -4

-6 -6
0 20 40 60 80 100 120 0 200 400 600 800 1000 1200
TIME (µs) TIME (µs)

FIGURE 25. VOLTAGE FOLLOWER LARGE SIGNAL PULSE FIGURE 26. VOLTAGE FOLLOWER LARGE SIGNAL PULSE
RESPONSE (IQ = 100µA) RESPONSE (IQ = 10µA)

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

11 FN2919.7
July 21, 2004