Professional Documents
Culture Documents
14862
14862
Indian Standard
ICS 91.100.40
BIS 2002
BUREAU
OF INDIAN
STANDARDS
Price Group 7
FOREWORD This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by the Cement Matrix Products Sectional Committee had been approved by the Civil Engineering Division Council. This standard has been formulated to fulfill the need for a specification for non-asbestos fibre cement flat sheets. In the formulation of this standard, due weightage has also been given to the international coordination among the standards and practices in different countries in addition to relating it to the practices in the field in this country. For this, assistance has been derived from the following: ISO 8336 : 1993 Fibre-cement flat sheets. International Organization for Standardization. ISO 390 : 1993 Products in fibre-reinforced cement Sampling and inspection. International Organization for Standardization. The composition of the technical committee responsible for formulation of this standard is given at Annex K. This edition 1.2 incorporates Amendment No. 1 (May 2002) and Amendment No. 2 (June 2003). Side bar indicates modification of the text as the result of incorporation of the amendments. For the purpose of deciding whether a particular requirement of this standard is compiled with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2 : 1960 Rules for rounding off numerical values ( revised ). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.
IS 14862 : 2000
Indian Standard
4 CLASSIFICATION 4.1 Flat sheets covered by this standard shall be of two types, namely, Type A and Type B. a) Type A Type A sheets are intended for external applications where they may be subjected to the direct action of sun, rain and/or snow. They may be supplied coated or uncoated. Type A sheets shall comply with the requirements of the type characteristics given in 6. b) Type B Type B sheets are not subjected to the type tests and are intended for internal applications and external applications where they will not be subjected to the direct action of sun, rain and/or snow.
NOTE If sheets of Type B are used in external applications where they are directly exposed to the weather but are protected (for example, coating or impregnation), the weather resistance of the product is determined by the quality of the protection. Specification of this protection and methods for control and test are outside the scope of this standard.
4.2 The sheets are further classified into five categories according to their modulus of rupture as given in Table 1. 4.3 The manufacturer shall declare the type and category of his product in his literature. 5 ACCEPTANCE CHARACTERISTICS 5.1 Dimensional and Geometrical Characteristics 5.1.1 Nominal Length and Width Flat fibre cement sheets shall be available in nominal lengths up to 3 000 mm and nominal widths up to 1 220 mm. Sheets of greater
IS 14862 : 2000
nominal lengths and widths may be supplied as agreed between the manufacturer and the supplier. The length and width shall be measured in accordance with the method given in Annex B.
NOTE The nominal dimensions (width and length) may be increased by 20 to 30 mm (oversize sheets) for application where the sheet is required to be cut by the user.
finished) product. When sampling is to be done from continuous production, testing of the base sheet prior to coating is acceptable when it can be shown that there is a correlation between the results of tests on sheets with and without coating. 5.2.1 Bending Strength When tested in accordance with the method given in Annex C, the minimum modulus of rupture of the sheets, expressed in MPa, shall be as specified in Table 1. The modulus of rupture shall be the average of the values obtained from testing the samples in both directions. Table 1 Minimum Modulus of Rupture ( Clauses 4.2, 5.2.1 and 6.1 )
Category (1) 1 2 3 4 5 Modulus of Rupture, Min (MPa)
5.1.2 Thickness Flat fibre cement sheets shall be of thickness from 3 to 30 mm, the thickness shall be measured in accordance with the method given in Annex B.
NOTE Thickness other than specified in 5.1.2 may be supplied by mutual agreement between the manufacturer and the purchaser.
5.1.3 Tolerances on Dimensions Tolerances on nominal dimensions shall be as follows: a) On length and width ( indicated by d ) d 1 000 mm: 5 mm 1 000 mm < d 1600 mm: 0.5 percent d > 1 600 mm: 8 mm These tolerances do not apply to oversize sheets. b) On thickness, e: e 6 mm: 0.6 mm e > 6 mm: 10 percent For sheets without texture on the exposed face, the maximum difference between extreme values of the thickness measurements within one sheet shall not exceed 15 percent of the maximum measured value.
NOTE Tighter tolerances may be adopted by agreement between the manufacturer and the purchaser.
Type A sheet strengths shall only be specified in the wet condition and the specimens shall be tested in the wet condition. Type B sheet strengths shall only be specified in the equilibrium condition and the specimens shall be tested in the equilibrium condition. When sampling is to be done from continuous production, these sheets may be tested on dry or saturated specimens, provided a relationship can be established between the equilibrium values and the dry or saturated values.
NOTE If the manufacturer includes product strengths in his literature, it should be clearly stated whether they are mean or minimum values.
5.1.4 Tolerances on Shape 5.1.4.1 Straightness of edges The tolerance on the straightness of edges shall be 3 mm/m for the relevant dimension (length or width) when measured in accordance with the method given in Annex B. 5.1.4.2 Squareness of edges The tolerance on the squareness of sheets shall be 4 mm/m when measured in accordance with the method given in Annex B.
NOTE Tighter tolerances may be adopted by agreement between the manufacturer and the purchaser.
5.2.2 Apparent Density The manufacturer shall specify in his literature the minimum apparent density for each category of sheet when tested in accordance with the method given in Annex C; the density shall be not less than this value. 5.2.3 Any additional characteristics, which the manufacturer desires to specify, may be mutually agreed between the manufacturer and the purchaser, including their method of testing and the requirements. 6 TYPE CHARACTERISTICS This clause applies to Type A sheets only. These tests shall be carried out on products as delivered. Where the tests are carried out on coated sheets, this shall be stated in the report. 2
5.2 Mechanical and Physical Characteristics Where the product is supplied coated, the following mechanical and physical specifications shall apply to the coated (that is
Type A Sheet (2) 7 13 18 Type B Sheet (3) 4 7 10 16 22
IS 14862 : 2000
6.1 Bending Strength When tested in accordance with the method given in Annex D, in equilibrium and wet conditions, the average modulus of rupture of each individual piece of the finished products shall not be less than the values for the appropriate category specified in Table 1. In addition, the mean modulus of rupture under wet conditions shall be not less than 50 percent of the mean modulus of rupture under equilibrium conditions. 6.2 Water Impermeability When tested in accordance with the method given in Annex E, traces of moisture may appear on the underside of the sheet, but in no instance shall there be formation of drops of water. 6.3 Frost Resistance For sheets for frost resistant applications, the sheets when tested in accordance with the method given in Annex F, after 50 freeze-thaw cycles, the limit Li of the average ratio r shall not be less than 0.75. 6.4 Warm Water When sheets are tested in accordance with the method given in Annex G, the limit Li of the average ratio r shall be greater than 0.75. 6.5 Soak-Dry When sheets are tested in accordance with the method given in Annex H, the limit Li of the average ratio r shall be greater than 0.75. 6.6 Heat-Rain This test shall be carried out on the finished product. When sheets are tested in accordance with the method given in Annex J, any visible cracks, delamination or other defects in the sheets shall not be of a degree such as to affect their performance in use. 7 TESTS 7.1 Acceptance Tests The objective of an acceptance test is to establish whether a batch of products conforms to a specification. The tests shall be performed on samples drawn either from continuous production or from a consignment ( see also 8 ). The acceptance tests shall be carried out at the manufacturers works on sheets and test specimens cut from sheets as delivered. The following acceptance tests shall be carried out: a) Dimensional and geometrical characteristics (compulsory) ( see Annex B ), b) Bending strength (compulsory) ( see Annex C ), and c) Apparent density (compulsory) ( see Annex C ). 3 7.2 Type Tests A type test is concerned with the approval of a new product and/or a fundamental change in formulation and/or method of manufacture, the effects of which cannot be predicted on the basis of former experience. The tests shall be performed on the as-delivered product. The test is required to demonstrate conformity of a generic product to a specification but is not required for each production batch. When type tests are carried out, the product shall also be subjected to the acceptance tests to ensure that it complies with the requirements of this standard. The following type tests shall be carried out: a) Bending strength ( see Annex D ), b) Water impermeability ( see Annex E ), c) Freeze-thaw ( see Annex F ), d) Warm water ( see Annex G ), e) Soak-dry ( see Annex H ), and f) Heat-rain test ( see Annex J ). Warm water, Freeze-Thaw and heat-rain test are optional tests as per the requirement of the purchaser. 8 SAMPLING AND ACCEPTANCE CRITERIA 8.1 Scale of Sampling 8.1.1 Lot In any consignment all the sheets of the same type and category, of the same thickness and manufactured under similar conditions of production (that is manufactured from the same formulation on the same forming machine without prolonged or abnormal interruptions and having the same acceptance requirement for relevant test) shall be grouped together to constitute a lot. 8.1.2 The number of sheets to be selected at random from the lot shall be in accordance with Table 2. 8.2 Inspection by Variables The inspection shall be carried out, on one sample, the size of which is given in col 2 of Table 2, as given in 8.2.1 to 8.2.7. 8.2.1 Divide the readings in the order in which they have been recorded into groups of 5, except when the sample size is 7, in which case the group size is the same as the sample size. 8.2.2 For each group, compute the range R. 8.2.3 From the group ranges R compute the average range R. 8.2.4 Compute the sample mean X by dividing the sum of the measurements by the sample size. 8.2.5 Obtain from col 3 of Table 2 the coefficient k. 8.2.6 Compute the acceptability limit AL and determine the acceptability of the lot by means of Table 3.
IS 14862 : 2000
8.2.7 The conformity of the lot to the requirement of this standard shall be obtained on the basis of the tests on the sheets selected from it. Table 2 Sample Size and Acceptance Coefficient ( Clauses 8.1.2, 8.2 and 8.2.5 )
Size of the Lot Sample Size Acceptance Coefficient (1) 150 151 to 180 181 to 500 501 to 1 200 1 201 to 3 200 3 201 to 10 000 (2) 3 3 4 5 7 10 (3) 0.502 0.502 0.450 0.431 0.405 0.507
9 INSPECTION AND MANUFACTURERS TEST CERTIFICATE 9.1 The purchaser or his representative shall have access at all reasonable times to the manufacturers stock area for the purpose of inspecting the materials and products and selecting and testing the sheets, which shall be so conducted as not to interfere unnecessarily with the loading in the carriers. 9.2 The manufacturer shall, upon request, furnish the purchaser or his representative with the certificate that the finished product complies with the specification in all respects.
10 MARKING Each sheet shall be indelibly stamped and marked by any suitable method with the following information: a) Indication of source of manufacturer; b) Date of manufacture; c) Type and category of sheet; d) Size and thickness of sheet; and e) The words FROST RESISTANT on the sheets suitable for frost resistant applications. 10.1 BIS Certification Marking Each sheet may also be marked with the Standard Mark. 10.1.1 The use of Standard Mark is governed by the provisions of the Bureau of Indian Standards Act, 1986 and the rules and regulations made thereunder. The details of conditions under which a licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained for the Bureau of Indian Standards. 11 SAFETY RULES a) Product Identification Sheets shall be marked with indelible characters to show that they do not contain asbestos. b) Information to Users The company should, through its distribution system, supply adequate information to the users concerning safety precautions to be taken during handling or machining of products and that excessive exposure to dust by cutting, drilling, sanding and turning or similar operations should be avoided by one or several of the following means: 1) using low speed power tools, 2) wetting the product, 3) using personal protective equipment (respirators), and 4) use of hand-tools.
ANNEX A
( Clause 2 ) LIST OF REFERRED INDIAN STANDARDS IS No. 269 : 1989 Title IS No. 3812 : 1981 8041 : 1990 8112 : 1989 12269 : 1987 4 Title Specification for fly ash for use as pozzolana and admixture ( first revision ) Specification for rapid hardening Portland cement ( second revision ) Specification for 43 grade ordinary Portland cement ( first revision ) Specification for 53 grade ordinary Portland cement
Specification for ordinary Portland cement, 33 grade ( fourth revision ) 455 : 1989 Portland slag cement ( fourth revision ) 1489 Specification for Portland pozzolana cement: (Part 1) : 1991 Fly ash based ( third revision ) (Part 2) : 1991 Calcined clay based ( third revision )
Alternative methods for determination of the average thickness of textured specimens may be used provided they can be proven, on average, to yield a thickness measurement within 2 percent of that determined from volume measurement. B-4 MEASUREMENT OF STRAIGHTNESS OF EDGES Apply each edge to the relevant arm of the square. Measure to the nearest 0.5 mm by means of a steel rule, the greatest separation between the edge of the sheet and the arm of the square. Report the results. Assess each result against the tolerance given in 5.1.4.1. B-5 MEASUREMENT OF OUT OF SQUARENESS OF EDGES Place each of the four corners of the sheet in succession between the arms of the square keeping the large side against the large arm and the other side in contact with small arm. In this position, measure the distance of the apex of the corner from the small arm of the square. Report each result. Assess the results against the tolerance given in 5.1.4.2.
C-1.2 Cutting Specimens The test specimens shall be cut from the same part of the sheet. One possible layout is shown in Fig. 2 (the distance of 200 mm is indicative). Other cutting layouts may be used provided that an equal number of specimens are cut perpendicular and parallel to the manufacturing direction.
C-1.3 Conditioning for Equilibrium Strength Place the test specimens for 7 days in an ambient condition and in such a manner that all faces are adequately ventilated. Record the temperature and relative humidity. C-1.4 Conditioning for Wet Strength Immerse the test specimens in water at ambient temperature for 24 h. The test specimens shall be tested immediately upon removal from the water. C-1.5 Apparatus The apparatus shall include the following items: a) Bending test machine ( see Fig. 3 ) with a constant rate of deflection when applying the load (where this facility is not available, a constant rate of loading is acceptable) and with an error of accuracy
IS 14862 : 2000
and an error of reproducibility equal to or less than 3 percent comprising: 1) two parallel supports, one rigid and one self aligning, the distance between the supports, a, being a function of the thickness of the test piece ( see Table 4 ). The upper faces of the supports shall be rounded and shall have a radius r between 3 mm and 25 mm. 2) a loading bar identical to the two supports shall be situated above the specimen so that it is parallel to the supports and at an equal distance from each support. Table 4 Distance Between Support Test Span [ Clause C-1.5 (a) ]
Test Specimen (1) Square Rectangular NOTES 1 For square specimens other distances between supports may be used provided compatibility can be demonstrated between results obtained with the different test spans and results obtained with the standard spans. 2 The distance between the axes of the supports may be reduced for narrow products, where full size specimens cannot be obtained, provided the distance is not less than 18e where e is thickness of the specimen, in mm. Distance Between Axes of Supports (Test Span), mm (2) 215 18e, Min
b) A micrometer reading to at least 0.05 mm with flat parallel metal jaws between 10 mm and 15 mm in diameter. C-1.6 Procedure Arrange the test piece with the underside against the supports and load the test piece along its centreline by means of the loading bar. Load the specimen such that breakage occurs within 10 to 30s. A constant rate of deflection is preferred; where this facility is not available a regular rate of loading is acceptable. Measure the thickness at two points for smooth specimens and four points for textural specimens along the section of breakage as indicated in Fig. 4. For square specimens, re-assemble the broken pieces. Submit the re-assembled test specimens to a second bending test with the line of load application at right angles to that of the first test. Measure the thickness of the test piece at two points for smooth sheets or four points for textured sheets along the new section of breakage as indicated in Fig. 4. Where rectangular test specimens are used, the strengths in the two directions are obtained by testing each of the appropriate specimens ( see Fig. 4 ). C-1.7 Expression and Interpretation of Results The modulus of rupture, Rf, in MPa, is given by the formula 3Pl Rf = -----------2 2be
IS 14862 : 2000
where P is the breaking load in N; l is the distance between axes of supports in mm; b is the width of the test piece, in mm; and e is the average thickness of the test piece (arithmetic average of two measurements for smooth and four measurements for textured), in mm. The modulus of rupture of the sheet shall be the arithmetic mean of the four values (two values in each direction). Assess the results against the requirement given in 5.2.1. C-2 MEASUREMENT OF APPARENT DENSITY C-2.1 Preparation of Specimens The test specimens shall be cut from sheets as delivered. The test piece should preferably be a piece of the sheet used for the bending test. C-2.2 Apparatus The apparatus shall include the following items: a) Ventilated oven capable of achieving a temperature of 100 to 105C with a full load of specimens; and where m is the mass of the test specimen after drying, in g; and V is the volume of the test specimen, in cm3 Assess the results against the requirement given in 5.2.2. b) Weighing scale accurate to within 0.1 percent, and equipped to determine the immersed mass of the specimen as well as the non-immersed mass. C-2.3 Procedure Determine the volume by immersion in water or another method having an equivalent accuracy. In the case of immersion in water, the test piece shall be saturated in water beforehand. Determine the mass by drying out the test specimens in a ventilated oven maintained at 100 to 105C for 24 1h. C-2.4 Expression and Interpretation of Results The density in grams per cubic centimetres, is given by the formula: = m ---V
ANNEX E
( Clause 6.2 ) METHOD OF TEST FOR WATER IMPERMEABILITY E-1 PREPARATION OF SPECIMEN Three test specimens shall be cut, that is, one from each of three sheets. Sheets used to provide specimens for other type-tests may be used or other sheets may be taken. Specimen dimensions shall be 600 mm 500 mm minimum except for narrow products when the dimensions shall be 600 mm the maximum possible width. E-2 EQUIPMENT A suitable frame, to be sealed on top of the specimen. The frame dimensions shall be 550 mm 450 mm minimum. A narrow frame of the same length shall be used for narrow products. E-3 SPECIMEN CONDITIONING The specimens shall be kept in a controlled environment for at least 7 days at ambient temperature. E-4 PROCEDURE Place and seal the frame on top of the face of the specimen and fill with water to a height of 20 mm above the face of the sheet. Place the specimens at ambient condition and record the temperature and relative humidity. The duration of the test shall be 24 h. E-5 EXPRESSION AND INTERPRETATION OF RESULTS Examine the underface after 24 h and verify that it conforms to the requirement given in 6.2.
10
ANNEX H
( Clauses 6.5 and 7.2 ) METHOD FOR SOAK-DRY TEST H-1 PREPARATION OF SPECIMENS Sample 10 sheets as-delivered by the producer. Cut 10 sets of paired specimens to suit the bending test in C-1. Each pair of specimens shall be cut adjacent from one sheet and given the same number for later comparison of results. H-2 APPARATUS The apparatus shall include the following items: a) Ventilated oven capable of achieving a temperature of 60 5C and a relative humidity of less than or equal to 20 percent with a full load of specimens; b) Bath filled with water at ambient conditions; and c) Equipment for bending test as defined in C-1. 11 H-3 PROCEDURE Divide the paired specimens to form two lots of 10 specimens each. After the conditioning procedure, submit the first lot of 10 specimens to the bending test as described in C-1. At the same time submit the second lot to 25 soak-dry cycles consisting of: a) immersion in water at ambient temperature for 18 h, and b) drying in a ventilated oven of 60 5C and relative humidity of less than 20 percent for 6 h. If necessary, an interval up to 72 h between cycles is allowed. During this interval, specimens shall be stored in immersed conditions. After 25 cycles, place the specimens in a laboratory atmosphere for 7 days. At the end of this period, carry out the wet bending test as specified in C-1.
IS 14862 : 2000
H-4 EXPRESSION AND INTERPRETATION OF RESULTS For each pair of specimens, i ( i = 1 to 10 ) calculate the individual ratio, ri, as follows: R fi ri = --------R fci where Rfi is the modulus of rupture of the ith specimen after the soak-dry cycling, and Rfci is the modulus of rupture of the ith reference test specimen (from the first lot). Calculate the average r , and standard deviation, s, of the individual ratios, ri. Calculate the 95 percent lower confidence limit, Li of the average ratio r as follows: L = r 0.58 s Assess the ratio against the requirement given in 6.6.
ANNEX J
( Clauses 6.6 and 7.2 ) METHOD FOR HEAT-RAIN TEST J-1 GENERAL This annex describes an optional test method to assess the performance of a cladding system composed of fibre cement sheets in a particular installation (sub-frame and fixings) under cyclic changes of heat and moisture. This test should be carried out on finished products. J-2 PRINCIPLE Sheets are fixed to a building frame in accordance with the recommended installation practices of the manufacturer. The system is then subjected to alternate wetting and heating cycles, following which any structural alteration is recorded. J-3 SAMPLING Sheets used for the test shall be drawn at random from the stock of finished products. The number of sheets required will depend upon the manufacturers installation recommendations and on the sheet size under test. J-4 APPARATUS Test installations with the following facilities: a) A sub-frame to which the sheets under test may be fixed vertically. b) Water spray system which will provide complete wetting of one face. c) Heating system to provide uniform radiant heat to give blackbody temperature across complete test frame surface of 60 5C and approximately uniform power output during the cycle. d) A control system allowing the test conditions to alternate automatically as prescribed in the test procedure. 12 J-5 TEST PROCEDURE Select a representative installation system. Assemble the system according to the manufacturers recommendations. The construction should include provision for at least one sheet joint in its central region. The perimeter of the frame should allow standard sheet edge finishing. The frame dimensions shall give a minimum area of 3.5 m2 and allow at least two sheets to be installed with normal orientation. If the area of each sheet is 1.8 m2 or more, use two specimens. If the combined area of the sheets exceeds 5 m2, the sheet length may be reduced to provide a test area of not more than 5 m2. If the area of each sheet is less than 1.8 m2, use sufficient number of sheets to cover an area of 3.5 m2. Fix the sample sheets to the test frame observing all the manufacturers recommendations. The edge fixing distance should be a minimum allowed and the centre distance between fixings should be the maximum allowed. Include all weather-proofing and other attachments normally specified in the assembly. Where sheets are recommended to have overlapping joints, assemble the test frame accordingly. Subject the assembled frame to the following test cycle: a) Water spray: 2 h 50 min b) pause: 10 min c) radiant heat: 2 h 50 min d) pause: 10 min The sheets shall be submitted to 25 cycles. Assess the product for visual defects against the requirement given in 6.6. J-6 OBSERVATIONS/REPORTING On completion of the final test cycle, inspect the sheets for damage or structural alteration caused by the test.
CHIEF ENGINEER (CEMENT CONCRETE ROAD) Municipal Corporation of Greater Mumbai, Mumbai DEPUTY CHIEF ENGINEER (PURCHASE) ( Alternate ) DR C. RAJKUMAR SHRI H. K. JULKA ( Alternate ) SHRI D. K. KANUNGO SHRI T. CHOUDHURY ( Alternate ) JOINT DIRECTOR STANDARDS (B&S) ASSISTANT DESIGN ENGINEER ( Alternate ) SHRI M. A. AZEEZ SHRI P. D. GAIKWAD ( Alternate ) SHRI N. P. RAJAMANE DR M. NEELAMEGAM ( Alternate ) SHRI C. H. SUBRAMANIAN SHRI A. DATTA ( Alternate ) SHRI C. Y. GAVHANE SHRI D. N. JOSHI ( Alternate ) SHRI S. HARIRAMASAMY SHRI B. V. B. PAI SHRI M. S. DANDWATE ( Alternate ) National Council for Cement and Building Materials, Ballabgarh National Test House, Calcutta Research, Designs and Standards Organization (Ministry of Railways), Lucknow Rural Electrification Corporation Ltd, New Delhi Structural Engineering Research Centre, Chennai Small Scale Industries Services Institute, Ministry of Industry, New Delhi Spun Pipes Manufacturers Association of Maharashtra, Pune Tamil Nadu Water Supply and Drainage Board, Chennai The Associated Cement Companies Ltd, Thane
( Continued on page 14 )
13
IS 14862 : 2000
( Continued from page 13 ) Members SHRI P. D. KELKAR SHRI P. R. C. NAIR ( Alternate ) SHRI S. S. SETHI, Director (Civ Engg) Representing The Indian Hume Pipe Co Ltd, Mumbai Director General, BIS ( Ex-officio Member ), BIS Member-Secretary SHRI SANJAY PANT Deputy Director (Civ Engg), BIS
14
Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country. Copyright BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to copyright be addressed to the Director (Publications), BIS. Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of BIS Catalogue and Standards : Monthly Additions. This Indian Standard has been developed from Doc : No. CED 53 (5783). Amendments Issued Since Publication Amend No. Amd. No. 1 Amd. No. 2 Date of Issue May 2002 June 2003
Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160022 Southern : C. I. T. Campus, IV Cross Road, CHENNAI 600113 Western : Manakalaya, E9 MIDC, Marol, Andheri (East) MUMBAI 400093
38 43 20 25
235 02 16, 235 04 42 235 15 19, 235 23 15 832 92 95, 832 78 58 832 78 91, 832 78 92
Branches : A H M E D A B A D . B A N G A L O R E . B H O P A L . B H U B A N E S H W A R . C O I M B A T O R E . FARIDABAD. GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR. NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISHAKHAPATNAM.