ACP Intro 2020R1 WS03.1 Rules

Workshop 03.
1 – Class40 –
Selection Rules
Introduction to
ANSYS Composite PrepPost
Release 2020 R1
1 © 2019 ANSYS, Inc.

3. Rules
Background
• Rules allow to modify the extension of both ply and OSS
• Modifying the geometry of the model and the realization of face imprints instead of
using rules are not the most efficient approaches for a ply-based modeling software like
ACP, which offers the possibility to define specific lay-up areas in a completely mesh and
geometry independent manner

3. Rules
Background
• The extension of the oriented selection sets is controlled by the element sets transferred
from Mechanical through named selections and optionally by rules.
Named Selections Selection Sets

3. Rules
Workshop Aim
• In this workshop rules will be used to modify the laminate of a class 40 boat to increase
reserve against failure, we will modify the lay-up by use of rules.
deck
Failure IRF
keel
tower
hull bulkhead
3. Rules
Start ANSYS Workbench and Open Archive
1
2
1. Start ANSYS Workbench and open the archive
Class40_FROM_START_<Release>.wbpz
2. Save the Workbench project

3. Rules 1
Update Project
2
1. Update the all project in the workbench schematic
2. Edit Results of ACP (Post) to start ACP
3. Rules
Check Failure Results

1. A failure plot is already present in the ACP tree, core failure is the most critical failure
mode
2. Add a new sampling point in the tree
2
1
Failure IRF

3. Rules

1 2 1
1
1.
3
In the general tab of the sampling point select one of the critical elements
2. Switch to the analysis tab and select the shown options
3. Press apply to generate the failure plot through the element thickness
4. After examining the results from the Sampling Point go back to ACP Pre
3. Rules
Create Parallel Rules in ACP
2
1
1. Add two new parallel rules ParalleRule.1 and ParallelRule.2
2. Specify origin, direction, lower and upper limits for the rules, select Include type
3. Rules
Create a Boolean Rule in ACP
1 2
1. Create a Boolean rule, it will be used to remove the core material on the deck in proximity
of the keel tower
2. Select the parallel rules defined before and specify an Intersect type
10 © 2019 ANSYS, Inc.
3. Rules
Remove the Core Material Under the Keel Tower
1 2 3
3 4 4
1. Double click on core ply in the deck modeling group
2. Switch to the Rules tab
3. Add the Boolean rule, select a Remove type for the rule
4.
11
Press apply, update the workbench project, and open ACP Post
© 2019 ANSYS, Inc.
4
3. Rules
Check Failure Results and Create a Sampling Point

1
1
1. Modify the Sampling Point position to the location 2 4
where the laminate is failing
2. Switch to the Analysis tab
3. Plot the failure plot across the laminate thickness
4. Return to ACP Pre to reinforce the laminate in this
3
position
12 © 2019 ANSYS, Inc.
The laminate fails on the inside of the deck at the boundary of
3. Rules the region where core material was removed
Add a Reinforcing Patch
2 3
2
1
1. Add a new ply after the Triax.4 ply in the deck modeling group
2. Select the deck oss, the Triax ply material already present in the model, a ply angle of 90
degree
3. Switch to the Rules tab and add the two parallel rules, select a rule Intersect type and
specify the usage of the rule as templates with the parameters shown here
13 © 2019 ANSYS, Inc.
3. Rules
1
Add a Reinforcing Patch (Excel Alternative)
1. Edit lay-up with Excel instead of directly creating a ply through the GUI as before
2. Select the appropriate modeling group from the ACP tree, choose to update the lay-up and select
open Excel
3. The laminate can be modified in Excel, new plies can be added
4. Recreate the lay-up by pulling the information from the spreadsheet
2
2 3 4 4
14
2
© 2019 ANSYS, Inc.
3. Rules
2
1. Update the workbench project
2. Open ACP Post to check the specified failure criteria on the deck laminate
15 © 2019 ANSYS, Inc.
3. Rules
Workshop Summary
• ACP allows to specify lay-up areas in a completely mesh (and geometry) independent manner
• Rules are used to define both ply and OSS extends
• Different rules can be combined with Boolean operations
• Rules can be re-used as templates
• How to iteratively improve the laminate
• How to realize detailed failure analysis using Sampling Points
• Explored the Excel interface

16 © 2019 ANSYS, Inc.

ACP Intro 2020R1 WS03.1 Rules

Uploaded by

Copyright:

Available Formats

ACP Intro 2020R1 WS03.1 Rules

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ACP Intro 2020R1 WS03.1 Rules

Uploaded by

Copyright:

Available Formats

Workshop 03.

1 © 2019 ANSYS, Inc.

2 © 2019 ANSYS, Inc.

Named Selections Selection Sets

3 © 2019 ANSYS, Inc.

Start ANSYS Workbench and Open Archive

5 © 2019 ANSYS, Inc.

Check Failure Results

7 © 2019 ANSYS, Inc.

Check Failure Results

Create Parallel Rules in ACP

Create a Boolean Rule in ACP

Remove the Core Material Under the Keel Tower

Check Failure Results and Create a Sampling Point

Add a Reinforcing Patch

Check Failure Results

• Rules are used to define both ply and OSS extends

• Different rules can be combined with Boolean operations

• Rules can be re-used as templates

• How to iteratively improve the laminate

• How to realize detailed failure analysis using Sampling Points

• Explored the Excel interface

You might also like