All About Needles

All About Needles
Download Product Info

689.1Kb PDF
Contents
The basic functions of a needle
Needle Parts: Physical characteristics
Needle Identification
Round Point Needles
Needle Size / Thickness
Comparison of Equivalent Needle Sizes
Common Problems and Solutions
Needle Checklist
Checking a Needle that is already in a Machine
Contact us about Needles
Introduction
The central feature of any sewing machine is the needle or needles. Very many needle types (systems) have been
developed over time to ensure each sewing machine that uses them performs at its best.
Needle systems may be introduced for a number of reasons such as the introduction of new or specialised fabrics,
new sewing machinery or even increases in machine speed.
Each needle system (needle type) will typically have between 6-8 sizes available, and in the more popular systems
there can be up to 15 sizes, with each of these needles systems and sizes being available in a range of different
needle points.
The following guide has been put together to help gain a better understanding of sewing machine needles.
The basic functions of a needle

1. To create a passage in the material for the thread to pass through.
2. To carry the needle thread through the material and form a loop which can be picked up by the hook or
looper mechanism.
3. To pass the needle thread through the loop formed by the looper mechanism on machines other than
lockstitch.
Needle Parts: Physical characteristics

A needle has various parts to execute different functions during the sewing operation as follows:
 Butt
The shaped top end which facilitates insertion into the needle bar/clamp
 Shank
The thicker part of the needle held by the needle clamp or the needle set screw. It supports the needle as a
whole by providing additional strength
 Shoulder
The intermediate section between the shank and the blade
 Blade
The needle portion extends from the shank to the eye. This is subjected to the greatest amount of friction
and hence heat when it passes through the material
 Long groove(s)
It is present in one side of the needle blade for the convenience of the needle thread from the take-up
device and provides a protective channel in which the thread is drawn down through the material during
stitch formation
 Short groove
It is formed on the other side of long groove, towards the shuttle, hook, or looper and it assists in throwing
the loop of needle thread
 Eye
The eye of the needle is present in the bottom end of the blade. Needle thread allowed through this eye is
taken to the bottom area
 Scarf (Clearance)
It is a clearance cut in the needle blade just above the eye to permit a closer setting of the shuttle, hook, or
looper to the needle
 Point
The point of the needle is shaped to provide the most suitable penetration of the material being sewn
according to its nature and the desired stitch effect
 Tip
The extreme tip shape, in combination with the point defines penetration performance
 Other variants
Most needles are constructed using these features but there are a number of exceptions. Some of which
may have been developed to overcome specific seaming issues or simply designed to meet the machine
requirements
Needle Identification
A sewing machine needle is identified with three parameters and they are:
 System
 Point
 Size
System
A needle system defines the dimensions of a needle to suit the machine type. Depending on the machine and its
stitch type, the needle is designed with variations in length of blade, shank thickness, type of eye etc. It is
advisable to check with the machine manufacturer for suitability of needle system to machine.
Point
A needle point is classified broadly into two types:
1. Round, set or cloth points

2. Cutting or leather points
Round Point Needles

There are believed to be around twenty different round points available out of these six are in common use.
Round Point Needles – Applications:
 Slim Set Point also referred to as acute round point (SPI)

This point is used for dense woven fabrics as it causes less damage, helps set a straighter stitch and
minimizes seam pucker.
Commonly used for microfibre and densely woven fabrics, coated materials, topstitching of collars and
cuffs in shirts.
 Set Cloth Point also referred to as normal round point (R)
This point is used for normal fabrics with standard seams as it pushes the yarn to the side.
 Light Ball Point (SES)
This point is used for sewing lightweight knitted fabric. It is sometimes used for fine denim and light,
densely woven material to avoid damaging the material.
 Medium Ball Point (SUK)
This point is used for sewing medium weight knitted fabric. It is also used for medium to coarse denims,
particularly sand-washed and stonewashed grades.
 Heavy Ball Point (SKF)
This point is used for coarse knitwear and for sewing dense woven elastic (it won’t push the elastic yarn
through).
 Special ball point (SKL)
Used for medium to course elastic materials with covered elastomeric threads and very coarse knitwear.
Cutting Point Needles
Cutting point needles have sharp tips like blades. These tips are available with a wide variety of cross-sectional
shapes such as lens, rounded, triangular and square. They can be used while sewing dense, non-fabric based
material. They pierce the material more readily than the round point types thereby generating less needle heat.
There are a large number of cutting points of which around 11 are in regular use.
Cutting Points Overview

Cutting points spear Cutting point wedges

Needle Size / Thickness
The size of a needle is generally represented in one of two ways (although there are others). One method is by a
number metric (Nm). This represents the diameter of the needle blade in hundredths of a millimetre measured just
above the scarf but not at any reinforced part of the blade. For example, a Nm 110 needle is 1.1 millimetre in
diameter, while a Nm 50 needle is half a millimetre in diameter.
The thickness of the blade on the right is 1.1mm wide which is shown in Nm as 110.
The alternative standard needle sizing method is the Singer/Asia numbering system sometimes referred to as the
American system that uses a number that represents a size.
Below shows these Nm and Singer comparisons along with a number of other size references.
Comparison of Equivalent Needle Sizes

Singer Metric (Nm) Union Special Lewis Merrow W&
3 35 - - - -
4 40 - - - -
5 45 - - - -
6 50 - - - -
7 55 22 - 0 22
8 60 - 2 0 24
9 65 25 - 0 25
10 70 27 2.5 1 27
11 75 029/030 - - 30
12 80 32 3 2 32
13 85 34 - - -
14 90 36 3.5 3 36
Singer Metric (Nm) Union Special Lewis Merrow W&
15 95 38 - - -
16 100 40 4 4 40
17 105 42 - - -
18 110 44 4.5 5 44
19 120 047/048 5 6 48
20 125 49 - - 49
21 130 - - 7 52
22 140 54 5.5 - -
22.5 150 60 6 8 -
23 160 - - - -
23.5 170 67 - 9 -
24 180 78 7 - -
25 200 079/080 - 10 -
26 230 90 - - -
27 250 100 - - -
28 280 110 - - -
29 300 120 - - -
30 330 - - - -
31 350 140 - - -
32 380 - - - -
32.5 400 156 - - -
Determining the Right Needle for a Thread

Here’s a quick way to determine if the thread and the sewing machine needle are compatible:
1. Take half a metre of the thread being used on the machine and thread it through the eye of a loose needle.
2. Hold the thread vertically with the needle at the top.
 If the needle is too big, it will drop to the bottom of the thread
 If the needle is too small, it will stick at the top of the thread
 If the needle is the right size, it will slowly spiral to the bottom of the thread
However, a larger-than-normal needle may have to be used to penetrate thicker fabric, or stitch over the top of
pronounced or bulky seams.
Common Problems and Solutions

Sewing machine needles can break during sewing and some of the common reasons for breakage are mentioned
below, along with the possible solutions:
Reason Solution
Usage of a poor quality needle Use good quality branded needles
Reason Solution
Pulling the fabric as you sew This puts stress on the needle and bends it out of place; so, care should b
The needle doesn’t go in properly Check your manual and make sure it is inserted properly in the machine
The needle is too delicate for the fabric Use heavy gauge needles for sewing heavier fabrics like denim
The presser foot is loose It will cause the needle to hit the foot and bend, so there should be a scre
Needle Checklist
Inserting a New Needle
 Always ensure the needle is the correct needle system for the sewing machine
 Make sure the needle size / eye fits the thread size being used
 Make sure the needle is pushed all the way into the needle holder
 Ensure that the angle of the needle is correct
 After inserting a needle in the machine turn the machine hand wheel manually to make sure the needle isn't
contacting any parts
Checking a Needle that is already in a Machine

 Is the needle inserted correctly?
 Is the needle contacting any machine parts?
 Is the needle bent?
 Is the eye rough or blocked with melted fibre?
 Is the point damaged?
 When in doubt change the needle!

All About Needles

Uploaded by

Copyright:

Available Formats

All About Needles

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

All About Needles

Uploaded by

Copyright:

Available Formats

All About Needles

Download Product Info

Contact us about Needles

The basic functions of a needle

Needle Parts: Physical characteristics

A needle point is classified broadly into two types:

1. Round, set or cloth points

Round Point Needles

Round Point Needles – Applications:

 Slim Set Point also referred to as acute round point (SPI)

Cutting Point Needles

Cutting Points Overview

Cutting points spear Cutting point wedges

Comparison of Equivalent Needle Sizes

Determining the Right Needle for a Thread

Common Problems and Solutions

Checking a Needle that is already in a Machine

You might also like