Strain

Simple Strain

Also known as unit deformation, strain is the ratio of the change in length caused by the

applied force, to the original length.

where δ is the deformation and L is the original length, thus ε is dimensionless.

Stress-Strain Diagram

Suppose that a metal specimen be placed in tension-compression testing machine. As

the axial load is gradually increased in increments, the total elongation over the gage

length is measured at each increment of the load and this is continued until failure of

the specimen takes place. Knowing the original cross-sectional area and length of the

specimen, the normal stress σ and the strain ε can be obtained. The graph of these

quantities with the stress σ along the y-axis and the strain ε along the x-axis is called

the stress-strain diagram. The stress-strain diagram differs in form for various

materials. The diagram shown below is that for a medium carbon structural steel.

Metallic engineering materials are classified as either ductile or brittle materials. A

ductile material is one having relatively large tensile strains up to the point of rupture

like structural steel and aluminum, whereas brittle materials has a relatively small

strain up to the point of rupture like cast iron and concrete. An arbitrary strain of 0.05

mm/mm is frequently taken as the dividing line between these two classes.
PROPORTIONAL LIMIT (HOOKE'S LAW)

From the origin O to the point called proportional limit, the stress-strain

curve is a straight line. This linear relation between elongation and the

axial force causing was first noticed by Sir Robert Hooke in 1678 and is

called Hooke's Law that within the proportional limit, the stress is

directly proportional to strain or

The constant of proportionality k is called the Modulus of Elasticity E or Young's Modulus

and is equal to the slope of the stress-strain diagram from O to P. Then

ELASTIC LIMIT

The elastic limit is the limit beyond which the material will no longer go back to its

original shape when the load is removed, or it is the maximum stress that may be

developed such that there is no permanent or residual deformation when the load is

entirely removed.

ELASTIC AND PLASTIC RANGES

The region in stress-strain diagram from O to P is called the elastic range. The region

from P to R is called the plastic range.

YIELD POINT

Yield point is the point at which the material will have an appreciable elongation or

yielding without any increase in load.

ULTIMATE STRENGTH

The maximum ordinate in the stress-strain diagram is the ultimate strength or tensile

strength.

RAPTURE STRENGTH

Rapture strength is the strength of the material at rupture. This is also known as the

breaking strength.
MODULUS OF RESILIENCE

Modulus of resilience is the work done on a unit volume of material as the force is

gradually increased from O to P, in Nm/m3. This may be calculated as the area under

the stress-strain curve from the origin O to up to the elastic limit E (the shaded area in

the figure). The resilience of the material is its ability to absorb energy without creating

a permanent distortion.

MODULUS OF TOUGHNESS

Modulus of toughness is the work done on a unit volume of material as the force is

gradually increased from O to R, in Nm/m3. This may be calculated as the area under

the entire stress-strain curve (from O to R). The toughness of a material is its ability to

absorb energy without causing it to break.

WORKING STRESS, ALLOWABLE STRESS, AND FACTOR OF SAFETY

Working stress is defined as the actual stress of a material under a given loading. The

maximum safe stress that a material can carry is termed as the allowable stress. The

allowable stress should be limited to values not exceeding the proportional limit.

However, since proportional limit is difficult to determine accurately, the allowable

stress is taken as either the yield point or ultimate strength divided by a factor of

safety. The ratio of this strength (ultimate or yield strength) to allowable strength is

called the factor of safety.

AXIAL DEFORMATION
In the linear portion of the stress-strain diagram, the stress is proportional to strain and

is given by

σ=Eε

since σ = P / A and ε = δ / L, then P / A = E δ / L. Solving for δ,

To use this formula, the load must be axial, the bar must have a uniform cross-sectional
area, and the stress must not exceed the proportional limit. If however, the cross
sectional area is not uniform, the axial deformation can be determined by considering a
differential length and applying integration.
If however, the cross-sectional area is not uniform, the axial deformation can be

determined by considering a differential length and applying integration.

where A = ty and y and t, if variable, must be expressed in terms of x.

For a rod of unit mass ρ suspended vertically from one end, the total elongation due to

its own weight is

M = unit mass x Length x Area

where ρ is in kg/m3, L is the length of the rod in mm, M is the total mass of the rod in

kg, A is the cross-sectional area of the rod in mm2, and g = 9.81 m/s2.

STIFFNESS, k

Stiffness is the ratio of the steady force acting on an elastic body to the resulting

displacement. It has the unit of N/mm.

k=P/δ
SOLVED PROBLEMS IN AXIAL DEFORMATION

Problem 206

A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is

suspended vertically from one end. It supports a tensile load of 20 kN at the lower end.

If the unit mass of steel is 7850 kg/m3 and E = 200 × 103 MN/m2, find the total

elongation of the rod.

Solution 206

Problem 207

A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the

weight of the wire, determine the required diameter if the stress is not to exceed 20 ksi

and the total elongation is not to exceed 0.20 in. Assume E = 29 × 10 6 psi.

Solution 207
Problem 208

A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and

shrunk onto a steel wheel 1500.5 mm in diameter. If the coefficient of static friction is

0.30, what torque is required to twist the tire relative to the wheel? Neglect the

deformation of the wheel. Use E = 200 GPa.

Solution 208

Problem 209

An aluminum bar having a cross-sectional area of 0.5 in2 carries the axial loads applied

at the positions shown in Fig. P-209. Compute the total change in length of the bar if E

= 10 × 106 psi. Assume the bar is suitably braced to prevent lateral buckling.

Solution 209
Problem 210

Solve Prob. 209 if the points of application of the 6000-lb and the 4000-lb forces are

interchanged.

Solution 210
Problem 211

A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig.

P211. Axial loads are applied at the positions indicated. Find the largest value of P that

will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in

the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the

assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and

Ebr = 83 GPa.

Solution 211
Problem 212

The rigid bar ABC shown in Fig. P-212 is hinged at A and supported by a steel rod at B.

Determine the largest load P that can be applied at C if the stress in the steel rod is

limited to 30 ksi and the vertical movement of end C must not exceed 0.10 in.

Solution 212
Problem 213

The rigid bar AB, attached to two vertical rods as shown in Fig. P-213, is horizontal

before the load P is applied. Determine the vertical movement of P if its magnitude is

50 kN.

Solution 213

Problem 214

The rigid bars AB and CD shown in Fig. P-214 are supported by pins at A and C and the

two rods. Determine the maximum force P that can be applied as shown if its vertical

movement is limited to 5 mm. Neglect the weights of all members.

Solution 214

Problem 215

A uniform concrete slab of total weight W is to be attached, as shown in Fig. P-215, to two rods

whose lower ends are on the same level. Determine the ratio of the areas of the rods so that the

slab will remain level.

Solution 215

Problem 216

As shown in Fig. P-216, two aluminum rods AB and BC, hinged to rigid supports, are pinned

together at B to carry a vertical load P = 6000 lb. If each rod has a cross sectional area of 0.60

in2 and E = 10 × 106 psi, compute the elongation of each rod and the horizontal and vertical

displacements of point B. Assume α = 30° and θ = 30°.

Solution 216
Problem 216
Problem 217

Problem 217

Solve Prob. 216 if rod AB is of steel, with E = 29 × 106 psi. Assume α = 45° and θ = 30°; all

other data remain unchanged.

Solution 217
Problem 218
Problem 219

Problem 218

A uniform slender rod of length L and cross sectional area A is rotating in a horizontal plane

about a vertical axis through one end. If the unit mass of the rod is ρ, and it is rotating at a

constant angular velocity of ω rad/sec, show that the total elongation of the rod is ρω2L3/3E.

Solution 218
Problem 220

Problem 219

A round bar of length L, which tapers uniformly from a diameter D at one end to a smaller

diameter d at the other, is suspended vertically from the large end. If w is the weight per unit

volume, find the elongation of the rod caused by its own weight. Use this result to determine

the elongation of a cone suspended from its base. Solution 219

SOLVED PROBLEMS IN STRAIN AND AXIAL DEFORMATION

Problem 203

The following data were recorded during the tensile test of a 14-mm-diameter mild steel rod. The

gage length was 50 mm.

Plot the stress-strain diagram and determine the following mechanical properties: (a)

proportional limits; (b) modulus of elasticity; (c) yield point; (d) ultimate strength; and

(e) rupture strength.

Solution 203

Problem 204

The following data were obtained during a tension test of an aluminum alloy. The initial

diameter of the test specimen was 0.505 in. and the gage length was 2.0 in.

Plot the stress-strain diagram and determine the following mechanical properties: (a)

proportional limit; (b) modulus of elasticity; (c) yield point; (d) yield strength at 0.2% offset; (e)

ultimate strength; and (f) rupture strength.

Solution 204
Problem 226
Problem 227

Problem 205

A uniform bar of length L, cross-sectional area A, and unit mass ρ is suspended vertically from

one end. Show that its total elongation is δ = ρgL2 / 2E. If the total mass of the bar is M, show

also that δ = MgL/2AE.

Solution 205