Professional Documents
Culture Documents
LANG MEKRA Manual Servicio International 7600 Standard
LANG MEKRA Manual Servicio International 7600 Standard
STANDARD - INTERNATIONAL
REPLACEMENT INSTRUCTIONS
Contents
Rev #4 Page 2 of 15
405 - Standard International Replacement Instructions
HEAD CLAMP
Remove the head clamp screws and the clamp(s). Make sure to save them for re-assembly.
Remove the old mirror head(s) and replace them with the new mirror heads.
Clamp Screw
Rev #4 Page 3 of 15
405 - Standard International Replacement Instructions
MIRROR HEAD
HEAD CLAMP
Step 2 - Remove Heater wires from old Heads and connect to main heater cable.
Unclip Bezel and Glass from old mirror head and unplug heater cable terminals from Glass heater foil.
BEZEL &
GLASS HOUSING
HEATER
CABLE
TERMINALS
Remove the head clams screws and clamp (s). Make sure to save them for re-assembly.
Rev #4 Page 4 of 15
405 - Standard International Replacement Instructions
Remove heater cables from mirror head(s) by pulling heater cable through small hole in mirror head.
Remove old mirror head(s) from bracket.
Using the marks on the tube, re-position new head(s) on the tube.
Re-assemble the bracket and the new mirror head(s) using the 2 head clamps and the 4 black screws.
Place two black mounting clamps over the bracket tube and on top of the socket joints.
Add (2) socket head screws per clamp and torque to 6 + 2 Nm.
Clamp Screw
Rev #4 Page 5 of 15
405 - Standard International Replacement Instructions
Insert the heater cable into the mirror head and place the grommet into the hole (Picture #2).
HOLE PLUG
Picture #2
Picture #3
Picture #1 Picture #2
Rev #4 Page 6 of 15
405 - Standard International Replacement Instructions
MIRROR HEAD
HEAD CLAMP
HEATER CABLE
CONNECTOR CUT LINE
Remove the head clamps screws and the clamps and save them for re-assembly.
Remove old head(s).
Cut the heater cable connector from the tube assembly heater cable and strip both wire ends.
Rev #4 Page 7 of 15
405 - Standard International Replacement Instructions
Step 2
Remove Heater wires from old Heads and connect to main heater cable.
Unclip Bezel and Glass from old head Housing and unplug heater cable terminals from Glass heater foil.
BEZEL &
GLASS HOUSING
HEATER
CABLE
TERMINAL
S
CONNECTOR
Cut the connector and discard it.
Keep the 2 heater wires and strip both end.
Rev #4 Page 8 of 15
405 - Standard International Replacement Instructions
Use the splice seals to connect the black heater wires to the main heater cable.
Step 3
Heads re-assembly to new Bracket
Using the marks on the tube, re-position both new heads on the tube.
Re-assemble the bracket and the 2 new head housings using the 2 head clamps and the 4 black screws.
Place two black mounting clamps over the bracket tube and on top of the socket joints.
Add (2) socket head screws per clamp and torque to 6 + 2 Nm.
Clamp Screw
Rev #4 Page 9 of 15
405 - Standard International Replacement Instructions
Step 4
Glass & Bezel re-assembly to Head Housing
Slide the heater cable into the head and place the grommet into the hole (picture #1).
Insert the 2 small black hole plugs in the housing for each head.
HOLE PLUG
picture #1
Rev #4 Page 10 of 15
405 - Standard International Replacement Instructions
HEAD CLAMP
Remove the head clamp screws and the clamp(s). Make sure to save them for re-assembly.
Remove the old mirror head(s) and replace them with the new mirror heads.
Clamp Screw
Rev #4 Page 11 of 15
405 - Standard International Replacement Instructions
MIRROR HEAD
HEAD CLAMP
Step 2 - Remove Heater wires from old Heads and connect to main heater cable.
Unclip Bezel and Glass from old mirror head and unplug heater cable terminals from Glass heater foil.
BEZEL &
GLASS HOUSING
HEATER
CABLE
TERMINAL
S
Remove the head clamp screws and clamp(s). Make sure to save them for re-assembly.
Rev #4 Page 12 of 15
405 - Standard International Replacement Instructions
Remove heater cables from mirror head(s). Remove old mirror head(s) from bracket.
Using the marks on the tube, re-position both new heads on the tube.
Re-assemble the bracket and the new mirror head(s) using the 2 head clamps and the 4 black screws.
Place two black mounting clamps over the bracket tube and on top of the socket joints.
Add (2) socket head screws per clamp and torque to 6 + 2 Nm.
Clamp Screw
TERMINAL
GROMMET
Rev #4 Page 13 of 15
405 - Standard International Replacement Instructions
Slide the heater cable into the head (Picture #1) and place the grommet into the hole (Picture #2).
HOLE PLUG
Picture #1 Picture #2
Assemble the glass and bezel assembly onto the main housing. Push the bezel down until all tabs
have snapped into the housing. Make sure all 6 clips are correctly in (Picture # 3).
Picture #1 Picture #3
Picture #2
Rev #4 Page 14 of 15
405 - Standard International Replacement Instructions
Receiver
Upper Bracket Arm
Tube Connector
Holder
Step #1 Assemble Holder to Tube Connector with the enclosed hardware. Bolt, washers, and nut
should be assembled in the order shown in the above picture. Apply Loctite to bolt and hand
tighten only.
Step #2 Align the Flip Out Arm with the Receiver and insert the Flip Out Arm into the Receiver
until centered.
Rev #4 Page 15 of 15