Gujarat Technological University: Page 1 of 3

GUJARAT TECHNOLOGICAL UNIVERSITY
Bachelor of Engineering
Subject Code: 3160104
BASIC CONTROL THEORY
B.E. 6thSEMESTER
Type of course: Engineering Science

Prerequisite: Basics of Maths
Rationale: In aircraft it is necessary to control three different types of axis i.e. yaw, pitch and roll. So
in order to control such axis it is necessary to understand the basic concepts of control and its detailed
theory.
Teaching and Examination Scheme:
Teaching Scheme Credits Examination Marks Total

L T P C Theory Marks Practical Marks Marks
ESE (E) PA (M) ESE (V) PA (I)
2 0 2 3 70 30 30 20 150
Contents:
Sr. Contents Total %

No. Hours Weightage
Unit 1: Introduction
Concept, Types of control system, Natural & Man made control
1 2 10
systems, Open Loop & Closed Loop systems, SISO,SIMO,MISO
and MIMO system, Examples of control systems.
Unit 2: Mathematical Models of Systems
Introduction to Mathematical Modeling, Modeling of mechanical
2 3 10
systems, Modeling of electrical systems, Modeling of Electro-
Mechanical Systems, Examples.
Unit 3: Block Diagrams & Signal Flow
3 Properties of block diagrams, Block diagram reductions, 3 10
Construction of SFG, Mason’s Gain Formula, Examples.
Unit 4: Time Domain Performance Analysis
Excitation functions, First Order, Second Order and Higher Order
4 Systems, Types of the system, Transient response, Steady State 5 20
Error, Error constants, s- plane root location and transient response,
Time response of second order system, Examples.
Unit 5: Stability Analysis of Control Systems
Introduction, Bode’s Plot, Polar plots, Hurwits Criterion, Routh-
5 Hurtwitz criterion, Nyquist Plot, Nyquist Stability Criterion, 5 10
Stability analysis, Relative Stability, Closed Loop Frequency
response of Unity feed Back System, Examples.
Unit 6: Root Locus Method
6 Introduction, Root Locus plots, Rules for construction of root loci, 3 10
Feedback systems, Stability Conditions.
Unit 7: State Space Analysis
Introduction, Comparison between modern control theory and
conventional control theory, concepts of State, State Variables and
7 5 10
State models, State Space Equations, Linear time-Invariant systems,
State model for single input single output linear system, State space
representation, Examples.
Unit 8: Composite Controllers
8 4 20
Introduction, Discontinuous Controller: ON-OFF Controller, ON-
Page 1 of 3
w.e.f. AY 2018-19
OFF controller with dead zone, Multi-Position Controller,
Continuous Controller: Proportional control, Derivative control,
Integral control, Proportional – Integral (PI) control, Proportional –
Derivative (PD) control, Proportional – Integral – Derivative (PID)
control, Special terminology, (proportional band, repeats per minute,
rate gain, direct action, reverse, action), desired features of a
feedback control algorithms, Proportional mode, integral mode,
derivative mode.
Suggested Specification table with Marks (Theory):
Distribution of Theory Marks

R Level U Level A Level N Level E Level C Level
35% 25% 20% 15% 5% 0%
Legends: R: Remembrance; U: Understanding; A: Application, N: Analyze and E: Evaluate C: Create
and above Levels (Revised Bloom’s Taxonomy).
Note: This specification table shall be treated as a general guideline for students and teachers. The
actual distribution of marks in the question paper may vary slightly from above table.
Reference Books:
1. Control Systems By A. Anand Kumar.
2. Control Theory By U. A. Bakshi& V. U. Bakshi.
3. Control System Engineering with SCILAB Exercise.
4. Process Control: Principles and Applications by SurekhaBhanot, Pub: Oxford University Press.
5. Control Systems By Rao V Dukkipati.
6. Automatic Control Systems By Prof B. S. Manke.
7. Process Control: Designing Processes and Control for Dynamic Performance by Thomas E. Marlin;
Pub: McGraw – Hill, International Edition.
Course Outcome:
After learning the course the students should be able to:
1. Understand the basic concepts of control systems.
2. Know the procedure about how to analyze the problem.
3. Design the mathematical model of the system.
4. Design the composite types of controllers for any closed loop system.
List of Experiments:
1. To study about MATLAB software and its application for Control System Analysis.
2. To study about various MATLAB commands for Control System.
3. To study about building and analyzing multi block models.
4. To study about system time response to Unit Step, Unit Impulse, Unit Ramp, Unit Parabolic
input signal.
5. To study the steady state error of type-zero, type-one and type-two control systems on standard
test input signals.
6. To study about Bode plot and Nyquist plot for stability analysis using MATLAB.
7. To study about root locus for stability analysis using MATLAB.
8. To study about Bode’s Plot for Frequency Response Analysis.
9. To study Simulation and Design using MATLAB.
10. To prepare P, I, D algorithm on MATLAB Simulink and visualize their response to the Step
Signal.
11. To prepare PI, PD and PiD algorithm on MATLAB Simulink and visualize their response to the
Step Signal.
Page 2 of 3
w.e.f. AY 2018-19
Major Equipment/Software: MATLAB software or SCILAB or any open source software.
List of Open Source Software: SCILAB.
Learning website:http://nptel.ac.in.
Page 3 of 3
w.e.f. AY 2018-19

Gujarat Technological University: Page 1 of 3

Uploaded by

Copyright:

Available Formats

Gujarat Technological University: Page 1 of 3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gujarat Technological University: Page 1 of 3

Uploaded by

Copyright:

Available Formats

GUJARAT TECHNOLOGICAL UNIVERSITY

Type of course: Engineering Science

Teaching Scheme Credits Examination Marks Total

Sr. Contents Total %

Suggested Specification table with Marks (Theory):

Distribution of Theory Marks

You might also like