Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 33 views

    MDS C01

    Uploaded by

    TripleOffset
    This material data sheet specifies requirements for carbon steel type 235 to be used in various products. It defines acceptable product standards, grades, heat treatment requirements, chemical composition limits, mechanical properties, non-destructive testing procedures, defect repair restrictions, and certification requirements. Manufacturers must have an ISO 9001 quality system and issue certificates according to EN 10204 Type 3.1, including heat treatment condition.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MDS C01

    Uploaded by

    TripleOffset
    33 views1 page
    This material data sheet specifies requirements for carbon steel type 235 to be used in various products. It defines acceptable product standards, grades, heat treatment requirements, chemical composition limits, mechanical properties, non-destructive testing procedures, defect repair restrictions, and certification requirements. Manufacturers must have an ISO 9001 quality system and issue certificates according to EN 10204 Type 3.1, including heat treatment condition.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This material data sheet specifies requirements for carbon steel type 235 to be used in various products. It defines acceptable product standards, grades, heat treatment requirements, chemical composition limits, mechanical properties, non-destructive testing procedures, defect repair restrictions, and certification requirements. Manufacturers must have an ISO 9001 quality system and issue certificates according to EN 10204 Type 3.1, including heat treatment condition.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    33 views1 page

    MDS C01

    Uploaded by

    TripleOffset
    This material data sheet specifies requirements for carbon steel type 235 to be used in various products. It defines acceptable product standards, grades, heat treatment requirements, chemical composition limits, mechanical properties, non-destructive testing procedures, defect repair restrictions, and certification requirements. Manufacturers must have an ISO 9001 quality system and issue certificates according to EN 10204 Type 3.1, including heat treatment condition.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    NORSOK standard M-630 Edition 5, September 2010

    MATERIAL DATA SHEET MDS C01 Rev. 4


    TYPE OF MATERIAL: Carbon Steel Type 235

    PRODUCT STANDARD GRADE ACCEPT. CLASS SUPPL. REQ.


    Wrought fittings ASTM A 234 WPB - S3
    Welded pipes ISO 3183 (API 5L) L245 (B) SAWL PSL 1 -
    Welded pipes ASTM A 672 C60, C70 t < 19 mm: Cl. 12 -
    t > 19 mm: Cl. 22, 32, 42 -
    Seamless pipes ASTM A 106 B - S6
    Forgings ASTM A 105 - - S4
    Plates ASTM A 516 60, 70 - -
    1. SCOPE This MDS specifies the selected options in the referred standard and additional requirements which
    shall be added or supersede the corresponding requirements in the referred standard.
    2. HEAT TREATMENT Forgings to A 105: Normalized.
    Welded pipes to ISO 3183: Stress relieved when the nominal thickness t ≤ 19 mm.
    3. MANUFACTURING Valves with nominal size NPS 4 and smaller may be machined from solid forgings in the
    terminology of ASTM A 788 on the following conditions:
    - Purchasers’ acceptance shall be obtained in each case.
    - Supplementary requirement S55 shall apply to all finished products.
    4. CHEMICAL All products: C ≤ 0.20 %, S ≤ 0.025 %, P ≤ 0.030 %,
    COMPOSITION
    CE(IIW) = C+Mn/6+(Cr+Mo+V)/5+(Cu+Ni)/15 ≤ 0.43.
    5. MECHANICAL All products: Elongation, A > 20%.
    PROPERTIES
    6. TEST SAMPLING Samples for production testing shall realistically reflect the properties in the actual component.

    7. NON DESTRUCTIVE Pipes to ISO 3183: RT of weld seam or RT at ends and US/Eddy Current of the remaining weld.
    TESTING Fittings to A 234: UT is not acceptable as replacement of RT.
    All products: NDT operators shall be certified in accordance with EN 473 or equivalent.
    8. REPAIR OF Weld repair of base material is not acceptable.
    DEFECTS
    9. CERTIFICATION The material manufacturer shall have a quality system certified in accordance with ISO 9001 and
    the system shall have undergone a specific assessment for the relevant materials.
    The material certificate shall be issued in accordance with EN 10204 Type 3.1, and shall include
    the following information:
    - Heat treatment condition

    NORSOK standard Page 15 of 133

    You might also like