Columns

Column Design: Design Calculations Page 1 of 198
COLUMN DESIGN CALCULATIONS

Project Name : IFSU
Client Name : IFSU
Engineer Name : ANMJR
Design File : C:\Users\63917\Documents\ANMJR\PROJECTS\ANMJR-2023-
IFSU\RCDC\cOLUMNS.rcdx
Analysis File : C:\Users\63917\Documents\ANMJR\PROJECTS\ANMJR-2023-
IFSU\STAAD ANALYSIS\IFSU.std
Analysis Last Modified : 19/01/2023 10:42:40 pm
Definitions Of Terms:
All forces in units kN and m
All reinforcement details like area, spacing in mm
Neutral axis angle for resultant design moment is with respect to local major axis.
Ratio to account for reduction of stiffness of columns
1 βdns =
due to sustained axial loads
Moment magnification factor for frames not braced
2 δns =
against sidesway
First-order relative deflection between the top and
3 Δo =
bottom of the story due to Vu in mm
4 ∑Pu = Total factored vertical load in kN. (Clause 10.10.5.2)
5 δu = Design displacement in mm
Modification factor reflecting the reduced mechanical
6 λ =
properties of concrete
Coefficient defining the relative contribution of
7 ac =
concrete strength to nominal wall shear strength
Cross-sectional area of a structural member measured
8 Ach = to the outside edges of transverse reinforcement in
sqmm
Gross area of concrete section bounded by web
9 Acv = thickness and length of section in the direction of
shear force considered in sqmm
Effective cross-sectional area within a joint in a plane
10 Aj = parallel to plane of reinforcement generating shear in
the joint in sqmm
Area of non-prestressed longitudinal tension
11 As =
reinforcement in sqmm
Minimum area of shear reinforcement within spacing
12 Avmin =
's' in sqmm
13 B = Width of column/ wall in mm
Cross-sectional dimension of member core measured
14 bc = to the outside edges of the transverse reinforcement
composing area Ash in mm
Distance from extreme compression fiber to neutral
15 c =
axis in mm
16 Cc = Clear cover to longitudinal reinforcement in mm
Factor relating actual moment diagram to an
file:///C:/Users/63917/AppData/Local/Temp/tmp38E8.tmp 03/03/2023
17 Cm = equivalent uniform moment diagram

18 D = Depth / diameter of column in mm
Distance from extreme compression fiber to centroid
19 d =
of longitudinal tension reinforcement in mm
Distance from extreme compression fiber to centroid
20 d' =
of longitudinal compression reinforcement,mm
21 Ec = Modulus of elasticity of concrete in N/sqmm
22 EI = Flexural stiffness of compression member in N-sqmm
Specified compressive strength of concrete cylinder in
23 f'c =
N/sqmm
24 fy = Specified yield strength of reinforcement in N/sqmm
Specified yield strength fy of transverse
25 fyt =
reinforcement in N/sqmm
Height of entire wall from base to top of wall segment
26 hw =
considered in mm
27 k = Effective length factor for compression member
Length of compression member in a frame, measured
28 lc =
center-to-center of the joints in the frame in mm
Moment of inertia of gross concrete section about
29 lg =
centroidal axis neglecting reinforcement in mm4
30 lw = Length of entire wall in mm
Un-supported length for compression member along
31 lux =
D in mm
Un-supported length for compression member along
32 luy =
B in mm
Moment capacity of section for a given NA angle at
33 MCap =
design Pu in kNm
Resultant design moment at a given load angle to
34 MRes =
local major axis in kNm
Factored moment amplified for the effects of member
35 Mc = curvature used for design of compression member in
kNm
Factored moment modified to account for effect of
36 Mm =
axial compression in kNm
Factored moment acting on a section along D in kNm
37 Mux =
(From Analysis)
Factored moment acting on a section along B in kNm
38 Muy =
(From Analysis)
Smaller factored end moment on a compression
39 M1 =
member in kNm
Factored end moment on a compression member at
40 M1ns = the end at which M1 acts, due to loads that cause no
appreciable sidesway in kNm
Factored end moment on compression member at the
41 M1s = end at which M1 acts, due to loads that cause
Smaller factored end moment on a compression
42 M1sldr =
member due to slenderness effect in kNm
Larger factored end moment on compression member

43 M2 =
in kNm
Minimum value of moment M2 as per minimum
44 M2min =
eccentricity of column
45 M2ns = end at which M2 acts, due to loads that cause no
46 M2s = end at which M2 acts, due to loads that cause
Largest factored end moment on a compression
47 M2sldr =
member due to slenderness effect in kNm
48 Mnb = Flexure Capacity for Beam
49 Mnc = Flexure Capacity for Column
Nominal Flexure strength of column at top along
50 Mnty =
depth in kNm
Nominal Flexure strength of column at bottom along
51 Mnby =
depth in kNm
Nominal Flexure strength of column at top along
52 Mntx =
width in kNm
Nominal Flexure strength of column at bottom along
53 Mnbx =
width in kNm
Factored axial force normal to cross section occurring
54 Nu =
simultaneously with Vu in kN
55 Pc = Critical buckling load in kN
Ratio of area of distributed transverse reinforcement
56 pt = to gross concrete area perpendicular to that
reinforcement
57 Pω = Ratio of As to B x d
58 Q = Stability index for storey
Radius of gyration of cross section of a compression
59 r =
member in mm
60 Vc = Nominal shear strength provided by concrete in kN
61 Vj = Shear Force acting at the joint in kN
62 Vn = Nominal shear strength in kN
63 Vn' = Nominal shear strength at joint in kN
64 Vus = Factored horizontal shear in a storey in kN
Factored shear at section along D in kN (From
65 Vux =
Analysis)
Shear induced due to column flexural capacity along
66 Vux1 =
width, kN
Shear due to enhanced earthquake factor along
67 Vux2 =
width, kN
Factored shear at section along B in kN (From
68 Vuy =
Analysis)
Shear induced due to column flexural capacity along
69 Vuy1 =
depth, kN
Shear due to enhanced earthquake factor along depth,
70 Vuy2 = kN
It is a Neutral Axis angle corresponding to load angle
71 β =
to find out MCap
Code References:
ACI 318M-2011
Sr.No Element Clause / table
Minimum area of longitudinal reinforcement
1 : 21.6.3
for column
Maximum area of longitudinal
2 : 21.6.3
reinforcement for column
Minimum longitudinal and transverse
3 : 21.9.2.1
reinforcement for wall
4 Minimum diameter of transverse ties : 7.10.5
5 Minimum spacing of transverse ties : 7.10.5
Maximum spacing of longitudinal and
6 : 21.9.2.1
transverse reinforcement for wall
7 Applicability of boundary element : 21.9.6
Area and spacing of special confining
8 : 21.6.4
reinforcement
9 Slenderness Moments : 10.10
Shear Strength provided by concrete for
10 : 11.2
column
11 Design of shear for non-ductile wall : 11.9
12 Design of shear for ductile wall : 21.9.4
13 Minimum Flexural Strength of Columns : 21.6.2.2
14 Shear Check at Column Joint : 21.7.4.1
15 Shear Strength of Column : 21.3.3 & 21.5.4
Lateral Load case is not been considered in analysis
General Data
Column No. : C1
Level : -1.5m To 0m
Design Code = ACI 318M - 2011
Grade Of Concrete (f'c) = C25 N/sqmm
Grade Of Steel (fy) = Fy275 N/sqmm
Consider Ductile = No
Column B = 300 mm
Column D = 300 mm
Clear Cover, Cc = 38 mm
Clear Floor Height @ lux = 1500 mm

Clear Floor Height @ luy = 1500 mm
No Of Floors = 1
No Of Columns In Group = 1
Load Data
Analysis Reference No. = 54
Critical Analysis Load Combination : 3
Load Combination = [1] : 1.4 (LOAD 1: DL)
Critical Location = Top Joint
Put = 235.83 kN
Muxt = -14.09 kNm
Muyt = 2.01 kNm
Vuxt = -3.12 kN
Vuyt = -17.44 kN
Pub = 240.28 kN
Muxb = 12.05 kNm
Muyb = -2.66 kNm
Vuxb = -3.12 kN
Vuyb = -17.44 kN
Check For Stability Index

Along D
Q = 0.01
0.01< 0.05, Column shall be designed as non-sway frame
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
Column Is Braced Along D
Slenderness Check along D
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 12.05 kNm
M2 = -14.09 kNm
34 - 12 x (M1/M2) = 44.26
17.32 < 44.26, Column not slender along D

Column Is Braced Along B
Slenderness Check along B
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 2.01 kNm
M2 = -2.66 kNm
34 - 12 x (M1/M2) = 43.04
17.32 < 43.04, Column not slender along B
Calculation of Design Moment

Direction Manalysis Msldr or Mc Mdesign-final
A B C
Major Axis Mux (top) -14.09 - -14.09
Major Axis Mux (bottom) 12.05 - 12.05
Minor Axis Muy (top) 2.01 - 2.01
Minor Axis Muy (bottom) -2.66 - -2.66
Where
A = Moments from analysis
B = Moment due to slenderness effect
C = Final design Moment = Maximum of (Manalysis, Maximum of (Msldr or Mc))
Final Critical Design Forces

Critical Case - Axial Load & BiAxial Bending
Pu = 235.83 kN
Mux = -14.09 kNm
Muy = 2.01 kNm
Resultant Moment (Combined Action)

Moment Capacity Check
Pt Calculated = 1.79
Reinforcement Provided = 8-#16
Load Angle = Tan-1(Muy/Mux)
= 8.11 deg
MRes = 14.24 kNm
( φ ) MCap = 69.85 kNm
Capacity Ratio = MRes/ MCap
= 0.204 < 1
Design Of Shear
Design for shear along D

Critical Load Combination = [4] : 1.2 (LOAD 1: DL) kN
Nu = 202.14 kN
Muy = 12.08 kNm
Vuy = -14.9453 kN
λ = 1
φ = 0.75
deff = 254 mm
ρw (50% of As provided) = 0.021
Mm = -11.82 kNm
φVcy = 106.49 kN
Vuy < φVcy
Link For Shear Design Along D are not required
Design for shear along B

Nu = 202.14 kN
Mux = 1.72 kNm
Vux = -2.6704 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -22.18 kNm
φVcx = 106.49 kN
Vux < φVcx
Link For Shear Design Along B are not required
Design Of Links
Links in the zone where special confining links are not required
Normal Links
Diameter of link = 10 mm
> Max. longitudinal bar dia / 4
= 4 mm
Criterion for spacing of normal links
Min. Longitudinal Bar dia X 16 = 256 mm
48 x diameter of links = 480 mm
Provided spacing = 250 mm
Table For Links

Note: Ductile Design of Links is Applicable Only For Boundary Elements
Required Provided
Normal Design Shear Design Ductile Design Normal Zone Ductile Zone
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C1
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 233.75 kN
Muxt = 26.3 kNm
Muyt = 4.19 kNm
Vuxt = 3.12 kN
Vuyt = -17.44 kN
Pub = 235.83 kN
Muxb = 14.09 kNm
Muyb = 2.01 kNm
Vuxb = 3.12 kN
Vuyb = -17.44 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = 14.09 kNm
M2 = 26.3 kNm
34 - 12 x (M1/M2) = 27.57
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 2.01 kNm
M2 = 4.19 kNm
34 - 12 x (M1/M2) = 28.25

A B C
Major Axis Mux (top) 26.3 - 26.3
Minor Axis Muy (bottom) 2.01 - 2.01
Where

Pu = 233.75 kN
Mux = 26.3 kNm
Muy = 4.19 kNm

= 9.05 deg
MRes = 26.63 kNm
( φ ) MCap = 69.28 kNm
= 0.384 < 1
Design Of Shear
Nu = 200.36 kN
Muy = 22.54 kNm
Vuy = -14.9453 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -1.15 kNm
φVcy = 106.3 kN
Vuy < φVcy

Nu = 200.36 kN
Mux = 3.59 kNm
Vux = 2.6704 kN
λ = 1
φ = 0.75
deff = 254 mm

Mm = -20.1 kNm
φVcx = 106.3 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C1
Level : 0.7m To 4.65m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 132.13 kN
Muxt = 22.37 kNm
Muyt = 3.48 kNm
Vuxt = 1.87 kN
Vuyt = -11.41 kN
Pub = 143.86 kN
Muxb = -22.67 kNm
Muyb = -3.92 kNm
Vuxb = 1.87 kN
Vuyb = -11.41 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 22.37 kNm
M2 = -22.67 kNm
34 - 12 x (M1/M2) = 45.84
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = 3.48 kNm
M2 = -3.92 kNm
34 - 12 x (M1/M2) = 44.65

A B C
Major Axis Mux (bottom) -22.67 - -22.67
Where

Pu = 132.13 kN
Mux = 22.37 kNm
Muy = 3.48 kNm

= 8.84 deg
MRes = 22.64 kNm
( φ ) MCap = 61.28 kNm
= 0.369 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
Critical Load Combination = kN
LL)
Nu = 117.09 kN
Muy = 20.93 kNm
Vuy = -10.4001 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 7.08 kNm
φVcy = 53.37 kN
Vuy < φVcy

Nu = 113.25 kN
Mux = 2.98 kNm
Vux = 1.6051 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -10.41 kNm
φVcx = 96.81 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C1
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Critical Location = Bottom Joint
Put = 30.15 kN
Muxt = 17.23 kNm
Muyt = 2.34 kNm
Vuxt = 1.94 kN
Vuyt = -14.03 kN
Pub = 38.64 kN
Muxb = -22.88 kNm
Muyb = -3.2 kNm
Vuxb = 1.94 kN
Vuyb = -14.03 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = 17.23 kNm
M2 = -22.88 kNm
34 - 12 x (M1/M2) = 43.03
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 2.34 kNm
M2 = -3.2 kNm
34 - 12 x (M1/M2) = 42.76

A B C
Where

Pu = 38.64 kN
Mux = -22.88 kNm
Muy = -3.2 kNm

= 7.97 deg
MRes = 23.1 kNm
( φ ) MCap = 51.87 kNm
= 0.445 < 1
Design Of Shear
Nu = 38.64 kN
Muy = 22.88 kNm
Vuy = -14.0275 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 18.31 kNm
φVcy = 49.71 kN
Vuy < φVcy

Nu = 25.84 kN
Mux = 2.01 kNm
Vux = 1.6617 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -1.05 kNm
φVcx = 86.25 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C2
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 388.48 kN
Muxt = 6.58 kNm

Muyt = 1.53 kNm
Vuxt = -2.89 kN
Vuyt = 8.72 kN
Pub = 392.93 kN
Muxb = -6.49 kNm
Muyb = -2.8 kNm
Vuxb = -2.89 kN
Vuyb = 8.72 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -6.49 kNm
M2 = 6.58 kNm
34 - 12 x (M1/M2) = 45.84
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 1.53 kNm
M2 = -2.8 kNm
34 - 12 x (M1/M2) = 40.57

A B C
Where

Pu = 392.93 kN
Mux = -6.49 kNm
Muy = -2.8 kNm

= 23.29 deg
MRes = 7.07 kNm
( φ ) MCap = 65.04 kNm
= 0.109 < 1
Design Of Shear
Nu = 332.98 kN
Muy = 5.64 kNm
Vuy = 7.4729 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -33.73 kNm
φVcy = 119.31 kN
Vuy < φVcy

Nu = 332.98 kN
Mux = 1.31 kNm
Vux = -2.4736 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -38.06 kNm
φVcx = 119.31 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C2
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 386.4 kN
Muxt = -12.68 kNm
Muyt = 3.55 kNm
Vuxt = 2.89 kN
Vuyt = 8.72 kN
Pub = 388.48 kN
Muxb = -6.58 kNm
Muyb = 1.53 kNm
Vuxb = 2.89 kN
Vuyb = 8.72 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check

K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -6.58 kNm
M2 = -12.68 kNm
34 - 12 x (M1/M2) = 27.77
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 1.53 kNm
M2 = 3.55 kNm
34 - 12 x (M1/M2) = 28.82

A B C
Where

Pu = 386.4 kN
Mux = -12.68 kNm
Muy = 3.55 kNm


= 15.64 deg
MRes = 13.17 kNm
( φ ) MCap = 68.39 kNm
= 0.193 < 1
Design Of Shear
Nu = 331.2 kN
Muy = 10.87 kNm
Vuy = 7.4729 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -28.29 kNm
φVcy = 119.14 kN
Vuy < φVcy

Nu = 331.2 kN
Mux = 3.04 kNm
Vux = 2.4736 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -36.12 kNm
φVcx = 119.14 kN
Vux < φVcx
Design Of Links
Normal Links

= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C2
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Load Combination = [2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2: LL)
Put = 246.41 kN
Muxt = -8.79 kNm
Muyt = 6.18 kNm
Vuxt = 2.71 kN
Vuyt = 4.49 kN
Pub = 256.47 kN
Muxb = 8.96 kNm
Muyb = -4.52 kNm
Vuxb = 2.71 kN
Vuyb = 4.49 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = -8.79 kNm
M2 = 8.96 kNm
34 - 12 x (M1/M2) = 45.77
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -4.52 kNm
M2 = 6.18 kNm
34 - 12 x (M1/M2) = 42.77

A B C

Where

Pu = 246.41 kN
Mux = -8.79 kNm
Muy = 6.18 kNm

= 35.14 deg
MRes = 10.74 kNm
( φ ) MCap = 60.16 kNm
= 0.179 < 1
Design Of Shear
Nu = 202.66 kN
Muy = 8.35 kNm
Vuy = 4.3458 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -15.62 kNm
φVcy = 106.54 kN
Vuy < φVcy

Nu = 202.66 kN
Mux = 4.24 kNm
Vux = 1.8627 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -19.72 kNm
φVcx = 106.54 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C2
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 38.7 kN
Muxt = -7.72 kNm
Muyt = 5.4 kNm
Vuxt = 4.64 kN
Vuyt = 6.25 kN
Pub = 45.98 kN
Muxb = 10.14 kNm
Muyb = -7.87 kNm
Vuxb = 4.64 kN
Vuyb = 6.25 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -7.72 kNm
M2 = 10.14 kNm
34 - 12 x (M1/M2) = 43.14
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 5.4 kNm
M2 = -7.87 kNm
34 - 12 x (M1/M2) = 42.23

A B C
Where

Pu = 45.98 kN
Mux = 10.14 kNm
Muy = -7.87 kNm

= 37.8 deg
MRes = 12.84 kNm
( φ ) MCap = 53.43 kNm

= 0.24 < 1
Design Of Shear
Nu = 50.95 kN
Muy = 11.34 kNm
Vuy = 7.1565 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 5.32 kNm
φVcy = 52.73 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 45.98 kN
Mux = 7.87 kNm
Vux = 4.6396 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 2.43 kNm
φVcx = 55.66 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm

Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C3
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 290.45 kN
Muxt = 1.17 kNm
Muyt = 2.45 kNm
Vuxt = -3.9 kN
Vuyt = 1.79 kN
Pub = 294.9 kN
Muxb = -1.51 kNm
Muyb = -3.4 kNm
Vuxb = -3.9 kN
Vuyb = 1.79 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 1.17 kNm
M2 = -1.51 kNm
34 - 12 x (M1/M2) = 43.32
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 2.45 kNm
M2 = -3.4 kNm
34 - 12 x (M1/M2) = 42.65

A B C
Where


Pu = 294.9 kN
Mux = -1.51 kNm
Muy = -3.4 kNm

= 66.05 deg
MRes = 3.72 kNm
( φ ) MCap = 64.81 kNm
= 0.057 < 1
Design Of Shear
Nu = 248.95 kN
Muy = 1.01 kNm
Vuy = 1.5348 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -28.43 kNm
φVcy = 111.25 kN
Vuy < φVcy

Nu = 248.95 kN
Mux = 2.1 kNm
Vux = -3.347 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -27.34 kNm
φVcx = 111.25 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C3
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 288.37 kN
Muxt = -2.43 kNm
Muyt = 5.19 kNm
Vuxt = 3.9 kN
Vuyt = 1.79 kN
Pub = 290.45 kN
Muxb = -1.17 kNm
Muyb = 2.45 kNm
Vuxb = 3.9 kN
Vuyb = 1.79 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -1.17 kNm
M2 = -2.43 kNm
34 - 12 x (M1/M2) = 28.2

K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 2.45 kNm
M2 = 5.19 kNm
34 - 12 x (M1/M2) = 28.32

A B C
Where

Pu = 288.37 kN
Mux = -2.43 kNm
Muy = 5.19 kNm

= 64.92 deg
MRes = 5.73 kNm
( φ ) MCap = 64.25 kNm
= 0.089 < 1
Design Of Shear

Nu = 247.17 kN
Muy = 2.08 kNm
Vuy = 1.5348 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -27.15 kNm
φVcy = 111.07 kN
Vuy < φVcy

Nu = 247.17 kN
Mux = 4.44 kNm
Vux = 3.347 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -24.78 kNm
φVcx = 111.07 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C3
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 186.37 kN
Muxt = -2.64 kNm
Muyt = 6.4 kNm
Vuxt = 2.93 kN
Vuyt = 1.24 kN
Pub = 196.43 kN
Muxb = 2.25 kNm
Muyb = -5.17 kNm
Vuxb = 2.93 kN
Vuyb = 1.24 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 2.25 kNm
M2 = -2.64 kNm
34 - 12 x (M1/M2) = 44.27
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -5.17 kNm
M2 = 6.4 kNm
34 - 12 x (M1/M2) = 43.71

A B C
Where

Pu = 186.37 kN
Mux = -2.64 kNm
Muy = 6.4 kNm

= 67.6 deg
MRes = 6.92 kNm
( φ ) MCap = 62.04 kNm
= 0.111 < 1
Design Of Shear
Nu = 150.74 kN
Muy = 1.98 kNm
Vuy = 0.9868 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -15.85 kNm
φVcy = 101.01 kN
Vuy < φVcy

Nu = 150.74 kN
Mux = 4.81 kNm
Vux = 2.2014 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -13.01 kNm
φVcx = 101.01 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C3
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data

Put = 28.04 kN
Muxt = -3.86 kNm
Muyt = 6.49 kNm
Vuxt = 5.04 kN
Vuyt = 2.83 kN
Pub = 35.32 kN
Muxb = 4.23 kNm
Muyb = -7.91 kNm
Vuxb = 5.04 kN
Vuyb = 2.83 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -3.86 kNm
M2 = 4.23 kNm
34 - 12 x (M1/M2) = 44.96
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 6.49 kNm
M2 = -7.91 kNm
34 - 12 x (M1/M2) = 43.84

A B C
Where

Pu = 35.32 kN
Mux = 4.23 kNm
Muy = -7.91 kNm

= 61.88 deg
MRes = 8.97 kNm
( φ ) MCap = 53.1 kNm
= 0.169 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 28.04 kN
Muy = 3.86 kNm
Vuy = 2.83 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 0.55 kNm
φVcy = 72.64 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 35.32 kN
Mux = 7.91 kNm
Vux = 5.0369 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 3.74 kNm
φVcx = 52.74 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C4
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 170.78 kN
Muxt = 3.09 kNm
Muyt = 2.57 kNm
Vuxt = -3.63 kN
Vuyt = 4.21 kN
Pub = 175.23 kN
Muxb = -3.22 kNm
Muyb = -2.87 kNm
Vuxb = -3.63 kN
Vuyb = 4.21 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 3.09 kNm
M2 = -3.22 kNm
34 - 12 x (M1/M2) = 45.51
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 2.57 kNm
M2 = -2.87 kNm
34 - 12 x (M1/M2) = 44.75

A B C
Where

Pu = 175.23 kN
Mux = -3.22 kNm
Muy = -2.87 kNm

= 41.71 deg
MRes = 4.32 kNm
( φ ) MCap = 58.45 kNm
= 0.074 < 1
Design Of Shear
Nu = 146.38 kN
Muy = 2.65 kNm
Vuy = 3.6103 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -14.66 kNm
φVcy = 100.53 kN
Vuy < φVcy

Nu = 146.38 kN
Mux = 2.21 kNm
Vux = -3.1127 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -15.1 kNm
φVcx = 100.53 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C4
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 168.7 kN
Muxt = -6.04 kNm

Muyt = 5.11 kNm
Vuxt = 3.63 kN
Vuyt = 4.21 kN
Pub = 170.78 kN
Muxb = -3.09 kNm
Muyb = 2.57 kNm
Vuxb = 3.63 kN
Vuyb = 4.21 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -3.09 kNm
M2 = -6.04 kNm
34 - 12 x (M1/M2) = 27.86
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 2.57 kNm
M2 = 5.11 kNm
34 - 12 x (M1/M2) = 27.96

A B C
Where

Pu = 168.7 kN
Mux = -6.04 kNm
Muy = 5.11 kNm

= 40.25 deg
MRes = 7.91 kNm
( φ ) MCap = 58.45 kNm
= 0.135 < 1
Design Of Shear
Nu = 144.6 kN
Muy = 5.18 kNm
Vuy = 3.6103 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -11.92 kNm
φVcy = 100.33 kN
Vuy < φVcy

Nu = 144.6 kN
Mux = 4.38 kNm
Vux = 3.1127 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.72 kNm
φVcx = 100.33 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C4

Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 99.14 kN
Muxt = -5.29 kNm
Muyt = 4.52 kNm
Vuxt = 2.25 kN
Vuyt = 2.58 kN
Pub = 109.2 kN
Muxb = 4.89 kNm
Muyb = -4.35 kNm
Vuxb = 2.25 kN
Vuyb = 2.58 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check

K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 4.89 kNm
M2 = -5.29 kNm
34 - 12 x (M1/M2) = 45.1
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -4.35 kNm
M2 = 4.52 kNm
34 - 12 x (M1/M2) = 45.55

A B C
Where

Pu = 99.14 kN
Mux = -5.29 kNm
Muy = 4.52 kNm


= 40.48 deg
MRes = 6.96 kNm
( φ ) MCap = 56.24 kNm
= 0.124 < 1
Design Of Shear
Nu = 86.21 kN
Muy = 4.48 kNm
Vuy = 2.2778 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -5.72 kNm
φVcy = 93.67 kN
Vuy < φVcy

Nu = 86.21 kN
Mux = 3.65 kNm
Vux = 1.824 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -6.54 kNm
φVcx = 93.67 kN
Vux < φVcx
Design Of Links
Normal Links

= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C4
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 19.77 kN
Muxt = -5.32 kNm
Muyt = 5.83 kNm
Vuxt = 4.1 kN
Vuyt = 4.22 kN
Pub = 27.05 kN
Muxb = 6.75 kNm
Muyb = -5.91 kNm
Vuxb = 4.1 kN
Vuyb = 4.22 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -5.32 kNm
M2 = 6.75 kNm
34 - 12 x (M1/M2) = 43.47
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 5.83 kNm
M2 = -5.91 kNm
34 - 12 x (M1/M2) = 45.83

A B C

Where

Pu = 27.05 kN
Mux = 6.75 kNm
Muy = -5.91 kNm

= 41.2 deg
MRes = 8.97 kNm
( φ ) MCap = 52.58 kNm
= 0.171 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 27.05 kN
Muy = 6.75 kNm
Vuy = 4.2231 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 3.55 kNm
φVcy = 51.91 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 19.77 kN
Mux = 5.83 kNm
Vux = 4.1043 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 3.49 kNm
φVcx = 51.85 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C5
Level : -1.5m To 0m

Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 144.26 kN
Muxt = -2.66 kNm
Muyt = -2.77 kNm
Vuxt = 2.95 kN
Vuyt = -3.2 kN
Pub = 148.72 kN
Muxb = 2.14 kNm
Muyb = 1.65 kNm
Vuxb = 2.95 kN
Vuyb = -3.2 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 2.14 kNm
M2 = -2.66 kNm
34 - 12 x (M1/M2) = 43.65
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 1.65 kNm
M2 = -2.77 kNm
34 - 12 x (M1/M2) = 41.17

A B C
Minor Axis Muy (top) -2.77 - -2.77
Where

Pu = 144.26 kN
Mux = -2.66 kNm
Muy = -2.77 kNm

= 46.16 deg
MRes = 3.83 kNm
( φ ) MCap = 57.69 kNm

= 0.066 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 122.36 kN
Muy = 2.42 kNm
Vuy = -2.9445 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.05 kNm
φVcy = 97.85 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 122.36 kN
Mux = 2.39 kNm
Vux = 2.4753 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.08 kNm
φVcx = 97.85 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm

Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C5
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 142.19 kN
Muxt = 4.89 kNm
Muyt = -4.83 kNm
Vuxt = -2.95 kN
Vuyt = -3.2 kN
Pub = 144.26 kN
Muxb = 2.66 kNm
Muyb = -2.77 kNm

Vuxb = -2.95 kN
Vuyb = -3.2 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = 2.66 kNm
M2 = 4.89 kNm
34 - 12 x (M1/M2) = 27.49
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = -2.77 kNm
M2 = -4.83 kNm
34 - 12 x (M1/M2) = 27.13

A B C
Where

Pu = 142.19 kN
Mux = 4.89 kNm
Muy = -4.83 kNm

= 44.62 deg
MRes = 6.87 kNm
( φ ) MCap = 57.64 kNm
= 0.119 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 120.58 kN
Muy = 4.48 kNm
Vuy = -2.9445 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -9.78 kNm
φVcy = 97.65 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:

LL)
Nu = 120.58 kN
Mux = 4.12 kNm
Vux = -2.4753 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -10.14 kNm
φVcx = 97.65 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C5
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 77.31 kN
Muxt = 3.86 kNm
Muyt = -3.35 kNm
Vuxt = -1.7 kN
Vuyt = -2.01 kN
Pub = 89.04 kN
Muxb = -4.06 kNm
Muyb = 3.37 kNm
Vuxb = -1.7 kN
Vuyb = -2.01 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 3.86 kNm
M2 = -4.06 kNm
34 - 12 x (M1/M2) = 45.42
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -3.35 kNm
M2 = 3.37 kNm
34 - 12 x (M1/M2) = 45.93

A B C
Where

Pu = 89.04 kN
Mux = -4.06 kNm
Muy = 3.37 kNm

= 39.72 deg
MRes = 5.28 kNm
( φ ) MCap = 55.71 kNm
= 0.095 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 64.69 kN
Muy = 3.33 kNm
Vuy = -1.7472 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -4.32 kNm
φVcy = 91.1 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 64.69 kN
Mux = 2.76 kNm
Vux = -1.401 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -4.89 kNm
φVcx = 91.1 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C5
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 17.16 kN
Muxt = 2.89 kNm
Muyt = -2.64 kNm
Vuxt = -2.2 kN
Vuyt = -2.17 kN
Pub = 25.65 kN
Muxb = -3.3 kNm
Muyb = 3.65 kNm
Vuxb = -2.2 kN
Vuyb = -2.17 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = 2.89 kNm
M2 = -3.3 kNm
34 - 12 x (M1/M2) = 44.54
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = -2.64 kNm
M2 = 3.65 kNm
34 - 12 x (M1/M2) = 42.69

A B C
Where

Pu = 25.65 kN
Mux = -3.3 kNm
Muy = 3.65 kNm

= 47.88 deg
MRes = 4.92 kNm
( φ ) MCap = 52.55 kNm
= 0.094 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 15.2 kN
Muy = 2.93 kNm
Vuy = -2.0571 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 1.13 kNm
φVcy = 55.17 kN
Vuy < φVcy

Nu = 25.65 kN
Mux = 3.65 kNm
Vux = -2.1994 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 0.61 kNm
φVcx = 64.41 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C6
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 227.43 kN
Muxt = 0.95 kNm
Muyt = 0.79 kNm
Vuxt = -1.46 kN
Vuyt = 1.38 kN
Pub = 231.89 kN
Muxb = -1.12 kNm
Muyb = -1.39 kNm
Vuxb = -1.46 kN
Vuyb = 1.38 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 0.95 kNm
M2 = -1.12 kNm
34 - 12 x (M1/M2) = 44.16
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 0.79 kNm
M2 = -1.39 kNm
34 - 12 x (M1/M2) = 40.85

A B C
Where

Pu = 231.89 kN
Mux = -1.12 kNm
Muy = -1.39 kNm

= 51.1 deg
MRes = 1.79 kNm
( φ ) MCap = 59.49 kNm
= 0.03 < 1
Design Of Shear
Nu = 194.94 kN
Muy = 0.82 kNm
Vuy = 1.1861 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -22.24 kNm
φVcy = 105.74 kN
Vuy < φVcy

Nu = 194.94 kN
Mux = 0.68 kNm
Vux = -1.25 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -22.37 kNm
φVcx = 105.74 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---

Spacing 250 --- --- 250 ---
General Data
Column No. : C6
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 225.35 kN
Muxt = -1.92 kNm
Muyt = 1.81 kNm
Vuxt = 1.46 kN
Vuyt = 1.38 kN
Pub = 227.43 kN
Muxb = -0.95 kNm
Muyb = 0.79 kNm
Vuxb = 1.46 kN
Vuyb = 1.38 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -0.95 kNm
M2 = -1.92 kNm
34 - 12 x (M1/M2) = 28.05
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 0.79 kNm
M2 = 1.81 kNm
34 - 12 x (M1/M2) = 28.75

A B C
Where

Pu = 225.35 kN
Mux = -1.92 kNm

Muy = 1.81 kNm

= 43.39 deg
MRes = 2.64 kNm
( φ ) MCap = 59.24 kNm
= 0.045 < 1
Design Of Shear
Nu = 193.16 kN
Muy = 1.65 kNm
Vuy = 1.1861 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.2 kNm
φVcy = 105.55 kN
Vuy < φVcy

Nu = 193.16 kN
Mux = 1.56 kNm
Vux = 1.25 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.29 kNm
φVcx = 105.55 kN
Vux < φVcx

Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C6
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data

Put = 154.56 kN
Muxt = 3.08 kNm
Muyt = 2.99 kNm
Vuxt = 1.46 kN
Vuyt = -0.99 kN
Pub = 164.62 kN
Muxb = -0.83 kNm
Muyb = -2.77 kNm
Vuxb = 1.46 kN
Vuyb = -0.99 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = -0.83 kNm
M2 = 3.08 kNm
34 - 12 x (M1/M2) = 37.22
39.84 > 37.22,Column slender along D
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -2.77 kNm
M2 = 2.99 kNm
34 - 12 x (M1/M2) = 45.11

Moment Magnification:
For Non-sway frame:
Along D
βdns = 0.6
Ec = 23500 N/sqmm
9 = 0.675 mm^4
Ig ( x 10 )
6 = 4579107.188 >N-sqmm
EI ( x 10 )
M2min = 3.95 kNm
Cm = 1
Pc = 3797.02 kN
δns = 1.06
Mc1 = -4.19 kN
Mc2 = 4.19 kN

A B C
Major Axis Mux (top) 3.08 4.19 4.19
Major Axis Mux (bottom) -0.83 -4.19 -4.19
Where

Pu = 154.56 kN
Mux = 4.19 kNm
Muy = 2.99 kNm

= 35.46 deg
MRes = 5.15 kNm
( φ ) MCap = 58.59 kNm

= 0.088 < 1
Design Of Shear
Nu = 121.05 kN
Muy = 0.97 kNm
Vuy = -0.1889 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -13.35 kNm
φVcy = 97.7 kN
Vuy < φVcy

Nu = 121.05 kN
Mux = 1.89 kNm
Vux = 1.0158 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.43 kNm
φVcx = 97.7 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm

Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C6
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 25.99 kN
Muxt = 3.37 kNm
Muyt = 1.47 kNm
Vuxt = 1 kN
Vuyt = -2.83 kN
Pub = 33.28 kN
Muxb = -4.71 kNm
Muyb = -1.39 kNm
Vuxb = 1 kN
Vuyb = -2.83 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = 3.37 kNm
M2 = -4.71 kNm
34 - 12 x (M1/M2) = 42.59
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = -1.39 kNm
M2 = 1.47 kNm
34 - 12 x (M1/M2) = 45.3

A B C
Where


Pu = 33.28 kN
Mux = -4.71 kNm
Muy = -1.39 kNm

= 16.39 deg
MRes = 4.91 kNm
( φ ) MCap = 52.09 kNm
= 0.094 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 33.28 kN
Muy = 4.71 kNm
Vuy = -2.8276 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 0.78 kNm
φVcy = 64.69 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 25.99 kN
Mux = 1.47 kNm
Vux = 0.999 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -1.6 kNm
φVcx = 86.27 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C7
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm

No Of Floors = 1
Load Data
Put = 379.89 kN
Muxt = -5.38 kNm
Muyt = 5.74 kNm
Vuxt = -8.26 kN
Vuyt = -6.68 kN
Pub = 384.34 kN
Muxb = 4.63 kNm
Muyb = -6.64 kNm
Vuxb = -8.26 kN
Vuyb = -6.68 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = 4.63 kNm
M2 = -5.38 kNm
34 - 12 x (M1/M2) = 44.31

K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 5.74 kNm
M2 = -6.64 kNm
34 - 12 x (M1/M2) = 44.37

A B C
Where

Pu = 384.34 kN
Mux = 4.63 kNm
Muy = -6.64 kNm

= 55.14 deg
MRes = 8.1 kNm
( φ ) MCap = 61.55 kNm
= 0.132 < 1
Design Of Shear

Nu = 325.62 kN
Muy = 4.61 kNm
Vuy = -5.7225 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -33.89 kNm
φVcy = 118.63 kN
Vuy < φVcy

Nu = 325.62 kN
Mux = 4.92 kNm
Vux = -7.0793 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -33.58 kNm
φVcx = 118.63 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C7
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 377.81 kN
Muxt = 10.06 kNm
Muyt = 11.52 kNm
Vuxt = 8.26 kN
Vuyt = -6.68 kN
Pub = 379.89 kN
Muxb = 5.38 kNm
Muyb = 5.74 kNm
Vuxb = 8.26 kN
Vuyb = -6.68 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = 5.38 kNm
M2 = 10.06 kNm
34 - 12 x (M1/M2) = 27.58
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 5.74 kNm
M2 = 11.52 kNm
34 - 12 x (M1/M2) = 28.02

A B C
Where

Pu = 377.81 kN
Mux = 10.06 kNm
Muy = 11.52 kNm

= 48.88 deg
MRes = 15.29 kNm
( φ ) MCap = 60.47 kNm
= 0.253 < 1
Design Of Shear
Nu = 323.83 kN
Muy = 8.62 kNm
Vuy = -5.7225 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -29.67 kNm
φVcy = 118.46 kN
Vuy < φVcy

Nu = 323.83 kN
Mux = 9.88 kNm
Vux = 7.0793 kN
λ = 1
φ = 0.75
deff = 254 mm

Mm = -28.42 kNm
φVcx = 118.46 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C7
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 322.71 kN
Muxt = 7.36 kNm
Muyt = 5.98 kNm
Vuxt = 3.27 kN
Vuyt = -3.71 kN
Pub = 332.77 kN
Muxb = -7.3 kNm
Muyb = -6.93 kNm
Vuxb = 3.27 kN
Vuyb = -3.71 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = -7.3 kNm
M2 = 7.36 kNm
34 - 12 x (M1/M2) = 45.89
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = 5.98 kNm
M2 = -6.93 kNm
34 - 12 x (M1/M2) = 44.36

A B C
Where

Pu = 332.77 kN
Mux = -7.3 kNm
Muy = -6.93 kNm

= 43.5 deg
MRes = 10.06 kNm
( φ ) MCap = 60.25 kNm
= 0.167 < 1
Design Of Shear
Nu = 200.24 kN
Muy = 5.49 kNm
Vuy = -3.0298 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -18.19 kNm
φVcy = 106.29 kN
Vuy < φVcy

Nu = 200.24 kN
Mux = 0.82 kNm
Vux = 1.3111 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -22.86 kNm
φVcx = 106.29 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C7
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 31.85 kN
Muxt = 4.41 kNm
Muyt = 5.23 kNm
Vuxt = 3.9 kN
Vuyt = -3.95 kN
Pub = 39.13 kN
Muxb = -6.89 kNm
Muyb = -5.91 kNm
Vuxb = 3.9 kN
Vuyb = -3.95 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = 4.41 kNm
M2 = -6.89 kNm
34 - 12 x (M1/M2) = 41.69
K = 1
r = 86.6 mm
Klux /r = 28.41
M1 = 5.23 kNm
M2 = -5.91 kNm
34 - 12 x (M1/M2) = 44.62

A B C
Where

Pu = 39.13 kN
Mux = -6.89 kNm
Muy = -5.91 kNm

= 40.63 deg
MRes = 9.07 kNm
( φ ) MCap = 53.18 kNm
= 0.171 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 39.13 kN
Muy = 6.89 kNm
Vuy = -3.9518 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 2.26 kNm
φVcy = 54.83 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 31.85 kN
Mux = 5.23 kNm
Vux = 3.8953 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 1.46 kNm
φVcx = 59.59 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C8
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 450.09 kN
Muxt = 2.2 kNm
Muyt = 6.04 kNm
Vuxt = -8.5 kN
Vuyt = 2.92 kN
Pub = 454.54 kN
Muxb = -2.18 kNm
Muyb = -6.7 kNm
Vuxb = -8.5 kN
Vuyb = 2.92 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -2.18 kNm
M2 = 2.2 kNm
34 - 12 x (M1/M2) = 45.92
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 6.04 kNm
M2 = -6.7 kNm
34 - 12 x (M1/M2) = 44.82

A B C
Where

Pu = 454.54 kN
Mux = -2.18 kNm
Muy = -6.7 kNm

= 71.96 deg
MRes = 7.04 kNm
( φ ) MCap = 66.43 kNm
= 0.106 < 1
Design Of Shear
Nu = 385.79 kN
Muy = 1.88 kNm
Vuy = 2.5027 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -43.74 kNm
φVcy = 124.11 kN
Vuy < φVcy

Nu = 385.79 kN
Mux = 5.18 kNm
Vux = -7.2822 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -40.44 kNm
φVcx = 124.11 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C8
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 448.01 kN
Muxt = -4.24 kNm
Muyt = 11.99 kNm
Vuxt = 8.5 kN
Vuyt = 2.92 kN
Pub = 450.09 kN
Muxb = -2.2 kNm
Muyb = 6.04 kNm
Vuxb = 8.5 kN
Vuyb = 2.92 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check

K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -2.2 kNm
M2 = -4.24 kNm
34 - 12 x (M1/M2) = 27.78
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 6.04 kNm
M2 = 11.99 kNm
34 - 12 x (M1/M2) = 27.95

A B C
Where

Pu = 448.01 kN
Mux = -4.24 kNm
Muy = 11.99 kNm


= 70.52 deg
MRes = 12.72 kNm
( φ ) MCap = 66.02 kNm
= 0.193 < 1
Design Of Shear
Nu = 384.01 kN
Muy = 3.63 kNm
Vuy = 2.5027 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -41.77 kNm
φVcy = 123.95 kN
Vuy < φVcy

Nu = 384.01 kN
Mux = 10.28 kNm
Vux = 7.2822 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -35.13 kNm
φVcx = 123.95 kN
Vux < φVcx
Design Of Links
Normal Links

= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C8
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 343.25 kN
Muxt = -4.37 kNm
Muyt = 9.08 kNm
Vuxt = 4.44 kN
Vuyt = 2.06 kN
Pub = 353.3 kN
Muxb = 3.75 kNm
Muyb = -8.46 kNm
Vuxb = 4.44 kN
Vuyb = 2.06 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 3.75 kNm
M2 = -4.37 kNm
34 - 12 x (M1/M2) = 44.29
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -8.46 kNm
M2 = 9.08 kNm
34 - 12 x (M1/M2) = 45.19

A B C

Where

Pu = 343.25 kN
Mux = -4.37 kNm
Muy = 9.08 kNm

= 64.29 deg
MRes = 10.08 kNm
( φ ) MCap = 64.69 kNm
= 0.156 < 1
Design Of Shear
Nu = 224.91 kN
Muy = 2.38 kNm
Vuy = 1.3023 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -24.22 kNm
φVcy = 108.83 kN
Vuy < φVcy

Nu = 224.91 kN
Mux = 3.16 kNm
Vux = 2.208 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -23.44 kNm
φVcx = 108.83 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C8
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 28.47 kN
Muxt = -4.52 kNm
Muyt = 7.1 kNm
Vuxt = 5.88 kN
Vuyt = 3.67 kN
Pub = 35.75 kN
Muxb = 5.98 kNm
Muyb = -9.71 kNm
Vuxb = 5.88 kN
Vuyb = 3.67 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -4.52 kNm
M2 = 5.98 kNm
34 - 12 x (M1/M2) = 43.07
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 7.1 kNm
M2 = -9.71 kNm
34 - 12 x (M1/M2) = 42.77

A B C
Where

Pu = 35.75 kN
Mux = 5.98 kNm
Muy = -9.71 kNm

= 58.37 deg
MRes = 11.41 kNm
( φ ) MCap = 53.13 kNm

= 0.215 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 35.75 kN
Muy = 5.98 kNm
Vuy = 3.6742 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 1.76 kNm
φVcy = 56.62 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 35.75 kN
Mux = 9.71 kNm
Vux = 5.8796 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 5.49 kNm
φVcx = 51.3 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm

Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C9
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 343.94 kN
Muxt = 2.89 kNm
Muyt = 5.4 kNm
Vuxt = -7.26 kN
Vuyt = 3.78 kN
Pub = 348.39 kN
Muxb = -2.78 kNm
Muyb = -5.48 kNm
Vuxb = -7.26 kN
Vuyb = 3.78 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -2.78 kNm
M2 = 2.89 kNm
34 - 12 x (M1/M2) = 45.55
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 5.4 kNm
M2 = -5.48 kNm
34 - 12 x (M1/M2) = 45.83

A B C
Where

Pu = 343.94 kN
Mux = 2.89 kNm
Muy = 5.4 kNm

= 61.9 deg
MRes = 6.12 kNm
( φ ) MCap = 63.59 kNm
= 0.096 < 1
Design Of Shear
Nu = 294.8 kN
Muy = 2.47 kNm
Vuy = 3.2359 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -32.39 kNm
φVcy = 115.72 kN
Vuy < φVcy

Nu = 294.8 kN
Mux = 4.63 kNm

Vux = -6.2205 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -30.23 kNm
φVcx = 115.72 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C9
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm

No Of Floors = 1
Load Data
Put = 341.86 kN
Muxt = -5.53 kNm
Muyt = 10.48 kNm
Vuxt = 7.26 kN
Vuyt = 3.78 kN
Pub = 343.94 kN
Muxb = -2.89 kNm
Muyb = 5.4 kNm
Vuxb = 7.26 kN
Vuyb = 3.78 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -2.89 kNm
M2 = -5.53 kNm
34 - 12 x (M1/M2) = 27.74

K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 5.4 kNm
M2 = 10.48 kNm
34 - 12 x (M1/M2) = 27.81

A B C
Where

Pu = 341.86 kN
Mux = -5.53 kNm
Muy = 10.48 kNm

= 62.2 deg
MRes = 11.85 kNm
( φ ) MCap = 63.74 kNm
= 0.186 < 1
Design Of Shear

Nu = 293.02 kN
Muy = 4.74 kNm
Vuy = 3.2359 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -29.91 kNm
φVcy = 115.55 kN
Vuy < φVcy

Nu = 293.02 kN
Mux = 8.98 kNm
Vux = 6.2205 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -25.67 kNm
φVcx = 115.55 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C9
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 226.51 kN
Muxt = -6.01 kNm
Muyt = 9.92 kNm
Vuxt = 4.72 kN
Vuyt = 2.8 kN
Pub = 236.57 kN
Muxb = 5.04 kNm
Muyb = -8.7 kNm
Vuxb = 4.72 kN
Vuyb = 2.8 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 5.04 kNm
M2 = -6.01 kNm
34 - 12 x (M1/M2) = 44.06
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -8.7 kNm
M2 = 9.92 kNm
34 - 12 x (M1/M2) = 44.52

A B C
Where

Pu = 226.51 kN
Mux = -6.01 kNm
Muy = 9.92 kNm

= 58.8 deg
MRes = 11.6 kNm
( φ ) MCap = 60.91 kNm
= 0.19 < 1
Design Of Shear
Nu = 178.73 kN
Muy = 3.83 kNm
Vuy = 1.9803 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -17.3 kNm
φVcy = 104.03 kN
Vuy < φVcy

Nu = 178.73 kN
Mux = 6.62 kNm
Vux = 3.4441 kN
λ = 1
φ = 0.75
deff = 254 mm

Mm = -14.51 kNm
φVcx = 104.03 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C9
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 32 kN
Muxt = -5.51 kNm
Muyt = 8.03 kNm
Vuxt = 6.83 kN
Vuyt = 4.65 kN
Pub = 39.28 kN
Muxb = 7.79 kNm
Muyb = -11.51 kNm
Vuxb = 6.83 kN
Vuyb = 4.65 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -5.51 kNm
M2 = 7.79 kNm
34 - 12 x (M1/M2) = 42.49
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 8.03 kNm
M2 = -11.51 kNm
34 - 12 x (M1/M2) = 42.37

A B C
Where

Pu = 39.28 kN
Mux = 7.79 kNm
Muy = -11.51 kNm

= 55.92 deg
MRes = 13.89 kNm
( φ ) MCap = 53.14 kNm
= 0.261 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 39.28 kN
Muy = 7.79 kNm
Vuy = 4.6496 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 3.14 kNm
φVcy = 53.43 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 39.28 kN
Mux = 11.51 kNm
Vux = 6.8317 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 6.86 kNm
φVcx = 50.91 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C10
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 221.45 kN
Muxt = 0.56 kNm
Muyt = 1.44 kNm
Vuxt = -2.28 kN
Vuyt = 0.55 kN
Pub = 225.91 kN
Muxb = -0.26 kNm
Muyb = -1.98 kNm
Vuxb = -2.28 kN
Vuyb = 0.55 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -0.26 kNm
M2 = 0.56 kNm
34 - 12 x (M1/M2) = 39.68
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 1.44 kNm
M2 = -1.98 kNm
34 - 12 x (M1/M2) = 42.72

A B C
Where

Pu = 225.91 kN
Mux = -0.26 kNm
Muy = -1.98 kNm

= 82.39 deg
MRes = 2 kNm
( φ ) MCap = 69.31 kNm
= 0.029 < 1
Design Of Shear
Nu = 189.82 kN
Muy = 0.48 kNm
Vuy = 0.4699 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.97 kNm
φVcy = 105.2 kN
Vuy < φVcy

Nu = 189.82 kN
Mux = 1.23 kNm
Vux = -1.9521 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.21 kNm
φVcx = 105.2 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C10
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data

Put = 219.37 kN
Muxt = -0.94 kNm
Muyt = 3.03 kNm
Vuxt = 2.28 kN
Vuyt = 0.55 kN
Pub = 221.45 kN
Muxb = -0.56 kNm
Muyb = 1.44 kNm
Vuxb = 2.28 kN
Vuyb = 0.55 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 8.08
M1 = -0.56 kNm
M2 = -0.94 kNm
34 - 12 x (M1/M2) = 26.89
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = 1.44 kNm
M2 = 3.03 kNm
34 - 12 x (M1/M2) = 28.31

A B C
Where

Pu = 219.37 kN
Mux = -0.94 kNm
Muy = 3.03 kNm

= 72.74 deg
MRes = 3.17 kNm
( φ ) MCap = 64.95 kNm
= 0.049 < 1
Design Of Shear
Nu = 188.03 kN
Muy = 0.81 kNm
Vuy = 0.4699 kN
λ = 1
φ = 0.75
deff = 254 mm

Mm = -21.43 kNm
φVcy = 105.01 kN
Vuy < φVcy

Nu = 188.03 kN
Mux = 2.6 kNm
Vux = 1.9521 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -19.64 kNm
φVcx = 105.01 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C10
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 137.1 kN
Muxt = -1.37 kNm
Muyt = 3.92 kNm
Vuxt = 1.97 kN
Vuyt = 0.66 kN
Pub = 148.83 kN
Muxb = 1.25 kNm
Muyb = -3.85 kNm
Vuxb = 1.97 kN
Vuyb = 0.66 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 45.61
M1 = 1.25 kNm
M2 = -1.37 kNm
34 - 12 x (M1/M2) = 45
45.61 > 45,Column slender along D
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = -3.85 kNm
M2 = 3.92 kNm
34 - 12 x (M1/M2) = 45.79
For Non-sway frame:
Along D
βdns = 0.6
Ec = 23500 N/sqmm
9 = 0.675 mm^4
Ig ( x 10 )
6 = 4579107.188 >N-sqmm
EI ( x 10 )
M2min = 3.57 kNm
Cm = 1
Pc = 2896.59 kN
δns = 1.07
Mc1 = 3.83 kN
Mc2 = -3.83 kN

A B C
Major Axis Mux (top) -1.37 -3.83 -3.83
Major Axis Mux (bottom) 1.25 3.83 3.83
Where


Pu = 137.1 kN
Mux = -3.83 kNm
Muy = 3.92 kNm

= 45.62 deg
MRes = 5.48 kNm
( φ ) MCap = 57.51 kNm
= 0.095 < 1
Design Of Shear
Nu = 117.51 kN
Muy = 1.17 kNm
Vuy = 0.5686 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.72 kNm
φVcy = 97.3 kN
Vuy < φVcy

Nu = 117.51 kN
Mux = 3.36 kNm
Vux = 1.6857 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -10.54 kNm
φVcx = 97.3 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C10
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 29.67 kN
Muxt = -0.32 kNm
Muyt = 0.66 kNm
Vuxt = 0.7 kN
Vuyt = 0.27 kN
Pub = 38.16 kN
Muxb = 0.46 kNm
Muyb = -1.33 kNm
Vuxb = 0.7 kN
Vuyb = 0.27 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 33.02
M1 = -0.32 kNm
M2 = 0.46 kNm
34 - 12 x (M1/M2) = 42.3
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = 0.66 kNm
M2 = -1.33 kNm
34 - 12 x (M1/M2) = 39.91

A B C
Where

Pu = 38.16 kN
Mux = 0.46 kNm
Muy = -1.33 kNm

= 71.05 deg
MRes = 1.41 kNm
( φ ) MCap = 52.72 kNm
= 0.027 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
Critical Load Combination = LL) kN

Nu = 24.44 kN
Muy = 0.18 kNm
Vuy = -0.1742 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -2.71 kNm
φVcy = 86.07 kN
Vuy < φVcy

Nu = 25.43 kN
Mux = 0.56 kNm
Vux = 0.5965 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -2.44 kNm
φVcx = 86.2 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C11
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 211.11 kN
Muxt = 4.05 kNm
Muyt = -0.54 kNm
Vuxt = -0.08 kN
Vuyt = 4.71 kN
Pub = 215.57 kN
Muxb = -3.02 kNm
Muyb = -0.66 kNm
Vuxb = -0.08 kN
Vuyb = 4.71 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -3.02 kNm
M2 = 4.05 kNm
34 - 12 x (M1/M2) = 42.93
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = -0.54 kNm
M2 = -0.66 kNm
34 - 12 x (M1/M2) = 24.26

A B C
Where

Pu = 211.11 kN
Mux = 4.05 kNm
Muy = -0.54 kNm

= 7.57 deg
MRes = 4.09 kNm
( φ ) MCap = 68.16 kNm
= 0.06 < 1
Design Of Shear
Nu = 180.96 kN
Muy = 3.47 kNm
Vuy = 4.0397 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -17.92 kNm
φVcy = 104.26 kN
Vuy < φVcy

Nu = 180.96 kN
Mux = 0.46 kNm
Vux = -0.0715 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -20.94 kNm
φVcx = 104.26 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C11
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data

Put = 209.04 kN
Muxt = -7.35 kNm
Muyt = -0.48 kNm
Vuxt = 0.08 kN
Vuyt = 4.71 kN
Pub = 211.11 kN
Muxb = -4.05 kNm
Muyb = -0.54 kNm
Vuxb = 0.08 kN
Vuyb = 4.71 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -4.05 kNm
M2 = -7.35 kNm
34 - 12 x (M1/M2) = 27.38
K = 1
r = 86.6 mm
Klux /r = 8.08
M1 = -0.48 kNm
M2 = -0.54 kNm
34 - 12 x (M1/M2) = 23.3

A B C
Where

Pu = 209.04 kN
Mux = -7.35 kNm
Muy = -0.48 kNm

= 3.73 deg
MRes = 7.37 kNm
( φ ) MCap = 68.41 kNm
= 0.108 < 1
Design Of Shear
Nu = 179.17 kN
Muy = 6.3 kNm
Vuy = 4.0397 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -14.89 kNm
φVcy = 104.07 kN
Vuy < φVcy

Nu = 179.17 kN
Mux = 0.41 kNm
Vux = 0.0715 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -20.78 kNm
φVcx = 104.07 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C11
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 129.85 kN
Muxt = -5.96 kNm
Muyt = 0.98 kNm
Vuxt = 0.33 kN
Vuyt = 3.15 kN
Pub = 141.58 kN
Muxb = 6.47 kNm
Muyb = -0.34 kNm
Vuxb = 0.33 kN
Vuyb = 3.15 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01

(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = -5.96 kNm
M2 = 6.47 kNm
34 - 12 x (M1/M2) = 45.06
K = 1
r = 86.6 mm
Klux /r = 45.61
M1 = -0.34 kNm
M2 = 0.98 kNm
34 - 12 x (M1/M2) = 38.22
45.61 > 38.22, Column slender along B
For Non-sway frame:
Along B
βdns = 0.6
Ec = 23500 N/sqmm
9 = 0.675 mm^4
Ig ( x 10 )
EI ( x 10 6) = 4579107.188 N-sqmm
M2min = 3.4 kNm
Cm = 1
Pc = 2896.59 kN
δns = 1.07
Mc1 = -3.63 kN
Mc2 = 3.63 kN

A B C
Minor Axis Muy (top) 0.98 3.63 3.63
Minor Axis Muy (bottom) -0.34 -3.63 -3.63
Where

Pu = 141.58 kN
Mux = 6.47 kNm
Muy = -3.63 kNm

= 29.34 deg
MRes = 7.42 kNm
( φ ) MCap = 58.38 kNm
= 0.127 < 1
Design Of Shear
Nu = 111.3 kN
Muy = 5.11 kNm
Vuy = 2.697 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -8.05 kNm
φVcy = 96.59 kN
Vuy < φVcy

Nu = 111.3 kN
Mux = 0.84 kNm

Vux = 0.2866 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -12.32 kNm
φVcx = 96.59 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C11
Column B = 300 mm
Column D = 300 mm

No Of Floors = 1
Load Data
Put = 22.7 kN
Muxt = -2.31 kNm
Muyt = -0.3 kNm
Vuxt = -0.14 kN
Vuyt = 2.26 kN
Pub = 31.19 kN
Muxb = 4.16 kNm
Muyb = 0.09 kNm
Vuxb = -0.14 kN
Vuyb = 2.26 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -2.31 kNm
M2 = 4.16 kNm
34 - 12 x (M1/M2) = 40.66

K = 1
r = 86.6 mm
Klux /r = 33.02
M1 = 0.09 kNm
M2 = -0.3 kNm
34 - 12 x (M1/M2) = 37.51

A B C
Where

Pu = 31.19 kN
Mux = 4.16 kNm
Muy = 0.09 kNm

= 1.22 deg
MRes = 4.16 kNm
( φ ) MCap = 50.64 kNm
= 0.082 < 1
Design Of Shear

Nu = 31.19 kN
Muy = 4.16 kNm
Vuy = 2.2613 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 0.47 kNm
φVcy = 70.81 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 21.21 kN
Mux = 0.31 kNm
Vux = -0.7761 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -2.19 kNm
φVcx = 85.65 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C12
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 283.13 kN
Muxt = -4.04 kNm
Muyt = -10.83 kNm
Vuxt = 12.65 kN
Vuyt = -5.58 kN
Pub = 287.58 kN
Muxb = 4.33 kNm
Muyb = 8.15 kNm
Vuxb = 12.65 kN
Vuyb = -5.58 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -4.04 kNm
M2 = 4.33 kNm
34 - 12 x (M1/M2) = 45.22
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 8.15 kNm
M2 = -10.83 kNm
34 - 12 x (M1/M2) = 43.03

A B C
Where

Pu = 283.13 kN
Mux = -4.04 kNm
Muy = -10.83 kNm

= 69.52 deg
MRes = 11.56 kNm
( φ ) MCap = 65.85 kNm
= 0.176 < 1
Design Of Shear
Nu = 242.68 kN
Muy = 3.47 kNm
Vuy = -4.7836 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -25.23 kNm
φVcy = 110.62 kN
Vuy < φVcy

Nu = 242.68 kN
Mux = 9.28 kNm
Vux = 10.8457 kN
λ = 1
φ = 0.75
deff = 254 mm

Mm = -19.42 kNm
φVcx = 110.62 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C12
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 281.05 kN
Muxt = 7.95 kNm
Muyt = -19.68 kNm
Vuxt = -12.65 kN
Vuyt = -5.58 kN
Pub = 283.13 kN
Muxb = 4.04 kNm
Muyb = -10.83 kNm
Vuxb = -12.65 kN
Vuyb = -5.58 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = 4.04 kNm
M2 = 7.95 kNm
34 - 12 x (M1/M2) = 27.9
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = -10.83 kNm
M2 = -19.68 kNm
34 - 12 x (M1/M2) = 27.4

A B C
Where

Pu = 281.05 kN
Mux = 7.95 kNm
Muy = -19.68 kNm

= 68.01 deg
MRes = 21.23 kNm
( φ ) MCap = 65.19 kNm
= 0.326 < 1
Design Of Shear
Nu = 240.9 kN
Muy = 6.81 kNm
Vuy = -4.7836 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.67 kNm
φVcy = 110.44 kN
Vuy < φVcy

Nu = 240.9 kN
Mux = 16.87 kNm
Vux = -10.8457 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -11.61 kNm
φVcx = 110.44 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C12
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 193.27 kN
Muxt = 6.49 kNm
Muyt = -14.75 kNm
Vuxt = -7.23 kN
Vuyt = -3.12 kN
Pub = 203.33 kN
Muxb = -5.82 kNm
Muyb = 13.8 kNm
Vuxb = -7.23 kN
Vuyb = -3.12 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = -5.82 kNm
M2 = 6.49 kNm
34 - 12 x (M1/M2) = 44.76
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = 13.8 kNm
M2 = -14.75 kNm
34 - 12 x (M1/M2) = 45.23

A B C
Where

Pu = 193.27 kN
Mux = 6.49 kNm
Muy = -14.75 kNm

= 66.24 deg
MRes = 16.12 kNm
( φ ) MCap = 62.11 kNm
= 0.26 < 1
Design Of Shear
Nu = 132.27 kN
Muy = 4.85 kNm
Vuy = -2.5081 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -10.79 kNm
φVcy = 98.96 kN
Vuy < φVcy

Nu = 132.27 kN
Mux = 5.87 kNm
Vux = -4.1974 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -9.78 kNm
φVcx = 98.96 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C12
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 29.46 kN
Muxt = 7 kNm
Muyt = -10.04 kNm
Vuxt = -9.05 kN
Vuyt = -5.6 kN
Pub = 36.74 kN
Muxb = -9.02 kNm
Muyb = 15.83 kNm
Vuxb = -9.05 kN
Vuyb = -5.6 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = 7 kNm
M2 = -9.02 kNm
34 - 12 x (M1/M2) = 43.31
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = -10.04 kNm
M2 = 15.83 kNm
34 - 12 x (M1/M2) = 41.61

A B C
Major Axis Mux (top) 7 - 7
Where

Pu = 36.74 kN
Mux = -9.02 kNm
Muy = 15.83 kNm

= 60.34 deg
MRes = 18.22 kNm
( φ ) MCap = 53.28 kNm
= 0.342 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 36.74 kN
Muy = 9.02 kNm
Vuy = -5.6009 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 4.67 kNm
φVcy = 51.96 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 36.74 kN
Mux = 15.83 kNm
Vux = -9.0489 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 11.49 kNm
φVcx = 49.82 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C13
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 337.5 kN
Muxt = 1.75 kNm
Muyt = -11.05 kNm
Vuxt = 13.1 kN
Vuyt = 1.78 kN
Pub = 341.95 kN
Muxb = -0.91 kNm
Muyb = 8.58 kNm
Vuxb = 13.1 kN
Vuyb = 1.78 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check

K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -0.91 kNm
M2 = 1.75 kNm
34 - 12 x (M1/M2) = 40.24
K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 8.58 kNm
M2 = -11.05 kNm
34 - 12 x (M1/M2) = 43.32

A B C
Where

Pu = 337.5 kN
Mux = 1.75 kNm
Muy = -11.05 kNm


= 80.99 deg
MRes = 11.19 kNm
( φ ) MCap = 72.79 kNm
= 0.154 < 1
Design Of Shear
Nu = 289.28 kN
Muy = 1.5 kNm
Vuy = 1.5229 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -32.7 kNm
φVcy = 115.19 kN
Vuy < φVcy

Nu = 289.28 kN
Mux = 9.47 kNm
Vux = 11.2243 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -24.73 kNm
φVcx = 115.19 kN
Vux < φVcx
Design Of Links
Normal Links

= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C13
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 335.42 kN
Muxt = -3 kNm
Muyt = -20.22 kNm
Vuxt = -13.1 kN
Vuyt = 1.78 kN
Pub = 337.5 kN
Muxb = -1.75 kNm
Muyb = -11.05 kNm
Vuxb = -13.1 kN
Vuyb = 1.78 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -1.75 kNm
M2 = -3 kNm
34 - 12 x (M1/M2) = 26.98
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = -11.05 kNm
M2 = -20.22 kNm
34 - 12 x (M1/M2) = 27.44

A B C
Major Axis Mux (top) -3 - -3

Where

Pu = 335.42 kN
Mux = -3 kNm
Muy = -20.22 kNm

= 81.57 deg
MRes = 20.44 kNm
( φ ) MCap = 73.17 kNm
= 0.279 < 1
Design Of Shear
Nu = 287.5 kN
Muy = 2.57 kNm
Vuy = 1.5229 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -31.43 kNm
φVcy = 115.02 kN
Vuy < φVcy

Nu = 287.5 kN
Mux = 17.33 kNm
Vux = -11.2243 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -16.67 kNm
φVcx = 115.02 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C13
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 230.33 kN
Muxt = -3.58 kNm
Muyt = -16.48 kNm
Vuxt = -7.95 kN
Vuyt = 1.72 kN
Pub = 240.39 kN
Muxb = 3.21 kNm
Muyb = 14.92 kNm
Vuxb = -7.95 kN
Vuyb = 1.72 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 3.21 kNm
M2 = -3.58 kNm
34 - 12 x (M1/M2) = 44.78
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = 14.92 kNm
M2 = -16.48 kNm
34 - 12 x (M1/M2) = 44.87

A B C
Where

Pu = 230.33 kN
Mux = -3.58 kNm
Muy = -16.48 kNm

= 77.75 deg
MRes = 16.86 kNm
( φ ) MCap = 67.73 kNm

= 0.249 < 1
Design Of Shear
Nu = 164.77 kN
Muy = 2.25 kNm
Vuy = 1.2084 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -17.24 kNm
φVcy = 102.53 kN
Vuy < φVcy

Nu = 164.77 kN
Mux = 7.51 kNm
Vux = -4.9012 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -11.97 kNm
φVcx = 102.53 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C13
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 34.51 kN
Muxt = -2.25 kNm
Muyt = -11.48 kNm
Vuxt = -10.47 kN
Vuyt = 1.89 kN
Pub = 41.79 kN
Muxb = 3.15 kNm
Muyb = 18.45 kNm
Vuxb = -10.47 kN
Vuyb = 1.89 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -2.25 kNm
M2 = 3.15 kNm
34 - 12 x (M1/M2) = 42.58
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = -11.48 kNm
M2 = 18.45 kNm
34 - 12 x (M1/M2) = 41.47

A B C
Where

Pu = 41.79 kN
Mux = 3.15 kNm
Muy = 18.45 kNm

= 80.31 deg
MRes = 18.72 kNm
( φ ) MCap = 52.4 kNm
= 0.357 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 34.51 kN
Muy = 2.25 kNm
Vuy = 1.8897 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -1.83 kNm
φVcy = 87.35 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 41.79 kN
Mux = 18.45 kNm
Vux = -10.4677 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 13.51 kNm
φVcx = 49.76 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C14
Level : -1.5m To 0m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 232.63 kN
Muxt = 2.76 kNm
Muyt = -10.34 kNm
Vuxt = 12.67 kN
Vuyt = 3.05 kN
Pub = 237.09 kN
Muxb = -1.81 kNm
Muyb = 8.67 kNm
Vuxb = 12.67 kN
Vuyb = 3.05 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 17.32
M1 = -1.81 kNm
M2 = 2.76 kNm
34 - 12 x (M1/M2) = 41.86

K = 1
r = 86.6 mm
Klux /r = 17.32
M1 = 8.67 kNm
M2 = -10.34 kNm
34 - 12 x (M1/M2) = 44.06

A B C
Where

Pu = 232.63 kN
Mux = 2.76 kNm
Muy = -10.34 kNm

= 75.03 deg
MRes = 10.7 kNm
( φ ) MCap = 66.61 kNm
= 0.161 < 1
Design Of Shear

Nu = 199.4 kN
Muy = 2.37 kNm
Vuy = 2.6154 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -21.21 kNm
φVcy = 106.2 kN
Vuy < φVcy

Nu = 199.4 kN
Mux = 8.86 kNm
Vux = 10.8633 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -14.72 kNm
φVcx = 106.2 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C14
Level : 0m To 0.7m
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 230.55 kN
Muxt = -4.9 kNm
Muyt = -19.21 kNm
Vuxt = -12.67 kN
Vuyt = 3.05 kN
Pub = 232.63 kN
Muxb = -2.76 kNm
Muyb = -10.34 kNm
Vuxb = -12.67 kN
Vuyb = 3.05 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 3.46
M1 = -2.76 kNm
M2 = -4.9 kNm
34 - 12 x (M1/M2) = 27.23
K = 1
r = 86.6 mm
Klux /r = 3.46
M1 = -10.34 kNm
M2 = -19.21 kNm
34 - 12 x (M1/M2) = 27.54

A B C
Where

Pu = 230.55 kN
Mux = -4.9 kNm
Muy = -19.21 kNm

= 75.69 deg
MRes = 19.82 kNm
( φ ) MCap = 66.81 kNm
= 0.297 < 1
Design Of Shear
Nu = 197.62 kN
Muy = 4.2 kNm
Vuy = 2.6154 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -19.17 kNm
φVcy = 106.02 kN
Vuy < φVcy

Nu = 197.62 kN
Mux = 16.46 kNm
Vux = -10.8633 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -6.9 kNm
φVcx = 106.02 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C14
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data

Put = 145.63 kN
Muxt = -4.63 kNm
Muyt = -17.76 kNm
Vuxt = -8.39 kN
Vuyt = 2.3 kN
Pub = 155.68 kN
Muxb = 4.46 kNm
Muyb = 15.37 kNm
Vuxb = -8.39 kN
Vuyb = 2.3 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01
(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 39.84
M1 = 4.46 kNm
M2 = -4.63 kNm
34 - 12 x (M1/M2) = 45.55
K = 1
r = 86.6 mm
Klux /r = 39.84
M1 = 15.37 kNm
M2 = -17.76 kNm
34 - 12 x (M1/M2) = 44.38

A B C
Where

Pu = 145.63 kN
Mux = -4.63 kNm
Muy = -17.76 kNm

= 75.38 deg
MRes = 18.35 kNm
( φ ) MCap = 61.94 kNm
= 0.296 < 1
Design Of Shear
Nu = 119.02 kN
Muy = 3.47 kNm
Vuy = 1.8546 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -10.6 kNm
φVcy = 97.47 kN
Vuy < φVcy

Nu = 119.02 kN
Mux = 13.24 kNm
Vux = -6.8867 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = -0.84 kNm
φVcx = 97.47 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---
General Data
Column No. : C14
Column B = 300 mm
Column D = 300 mm
No Of Floors = 1
Load Data
Put = 25.34 kN
Muxt = -3.66 kNm
Muyt = -12.31 kNm
Vuxt = -11.28 kN
Vuyt = 2.82 kN
Pub = 32.62 kN
Muxb = 4.41 kNm
Muyb = 19.95 kNm
Vuxb = -11.28 kN
Vuyb = 2.82 kN

Along D
Q = 0.01
(Braced)
Along B
Q = 0.01

(Braced)
Slenderness Check
K = 1
r = 86.6 mm
Kluy /r = 28.41
M1 = -3.66 kNm
M2 = 4.41 kNm
34 - 12 x (M1/M2) = 43.94
K = 1
r = 86.6 mm
Klux /r = 27.25
M1 = -12.31 kNm
M2 = 19.95 kNm
34 - 12 x (M1/M2) = 41.4

A B C
Where

Pu = 32.62 kN
Mux = 4.41 kNm
Muy = 19.95 kNm

= 77.52 deg
MRes = 20.44 kNm
( φ ) MCap = 51.75 kNm
= 0.395 < 1
Design Of Shear
[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 25.34 kN
Muy = 3.66 kNm
Vuy = 2.8232 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 0.66 kNm
φVcy = 67.96 kN
Vuy < φVcy

[2] : 1.2 (LOAD 1: DL) +1.6 (LOAD 2:
LL)
Nu = 32.62 kN
Mux = 19.95 kNm
Vux = -11.2833 kN
λ = 1
φ = 0.75
deff = 254 mm
Mm = 16.1 kNm
φVcx = 49.37 kN
Vux < φVcx
Design Of Links
Normal Links
= 4 mm
Table For Links

Required Provided
Link Dia. 10 --- --- 10 ---
Spacing 250 --- --- 250 ---

Columns

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Columns

Uploaded by

Copyright:

Available Formats

Column Design: Design Calculations Page 1 of 198

COLUMN DESIGN CALCULATIONS

17 Cm = equivalent uniform moment diagram

Larger factored end moment on compression member

Lateral Load case is not been considered in analysis

Clear Floor Height @ lux = 1500 mm

Check For Stability Index

17.32 < 44.26, Column not slender along D

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along D

Design for shear along B

Table For Links

Check For Stability Index

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along B

ρw (50% of As provided) = 0.021

Table For Links

Check For Stability Index

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along B

Table For Links

Check For Stability Index

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along B

Table For Links

Muxt = 6.58 kNm

Check For Stability Index

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along B

Table For Links

Check For Stability Index

Column Is Braced Along D

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Load Angle = Tan-1(Muy/Mux)

Design for shear along B

> Max. longitudinal bar dia / 4

Table For Links

Check For Stability Index

Calculation of Design Moment

Major Axis Mux (bottom) 8.96 - 8.96

Final Critical Design Forces

Resultant Moment (Combined Action)

Design for shear along B

Table For Links

Check For Stability Index

Calculation of Design Moment

Final Critical Design Forces

Resultant Moment (Combined Action)

Capacity Ratio = MRes/ MCap

Design for shear along B

48 x diameter of links = 480 mm