Snvs 036 K

Product Sample & Technical Tools & Support &
Folder Buy Documents Software Community
LM2670
SNVS036K – APRIL 2000 – REVISED JUNE 2016
LM2670 SIMPLE SWITCHER® High Efficiency 3-A Step-Down Voltage Regulator With Sync
1 Features 3 Description
•
1 Efficiency Up to 94% The LM2670 series of regulators are monolithic
integrated circuits which provide all of the active
• Simple and Easy to Design With (Using Off-the- functions for a step-down (buck) switching regulator
Shelf External Components) capable of driving up to 3-A loads with excellent line
• 150-mΩ DMOS Output Switch and load regulation characteristics. High efficiency
• 3.3-V, 5-V, 12-V Fixed Output and Adjustable (>90%) is obtained through the use of a low ON-
(1.2 V to 37 V) Versions resistance DMOS power switch. The series consists
of fixed output voltages of 3.3-V, 5-V, and 12-V
• 50-µA Standby Current When Switched OFF output version.
• ±2% Maximum Output Tolerance Over Full Line
The SIMPLE SWITCHER® concept provides for a
and Load Conditions
complete design using a minimum number of external
• Wide Input Voltage Range: 8 V to 40 V components. The switching clock frequency can be
• External Sync Clock Capability provided by an internal fixed frequency oscillator
(280 kHz to 400 kHz) (260 kHz) or from an externally provided clock in the
• 260-kHz Fixed Frequency Internal Oscillator range of 280 kHz to 400 kHz which allows the use of
physically smaller sized components. A family of
• –40 to 125°C Operating Junction Temperature standard inductors for use with the LM2670 are
Range available from several manufacturers to greatly
simplify the design process. The external sync clock
2 Applications provides direct and precise control of the output ripple
frequency for consistent filtering or frequency
• Simple-to-Design, High Efficiency (>90%) Step-
spectrum positioning.
Down Switching Regulators
• Efficient System Preregulator for Linear Voltage The LM2670 series also has built-in thermal
Regulators shutdown, current limiting and an ON/OFF control
input that can power down the regulator to a low
• Battery Chargers 50‑µA quiescent current standby condition. The
• Communications and Radio Equipment Regulator output voltage is ensured to a ±2% tolerance.
With Synchronized Clock Frequency
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TO-263 (7) 10.10 mm × 8.89 mm
LM2670 TO-220 (7) 14.986 mm × 10.16 mm
VSON (14) 6.00 mm × 5.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2670
SNVS036K – APRIL 2000 – REVISED JUNE 2016 www.ti.com
Table of Contents
1 Features .................................................................. 1 7.4 Device Functional Modes........................................ 12
2 Applications ........................................................... 1 8 Application and Implementation ........................ 13
3 Description ............................................................. 1 8.1 Application Information............................................ 13
4 Revision History..................................................... 2 8.2 Typical Applications ................................................ 16
5 Pin Configuration and Functions ......................... 3 9 Power Supply Recommendations...................... 26
6 Specifications......................................................... 4 10 Layout................................................................... 27
6.1 Absolute Maximum Ratings ...................................... 4 10.1 Layout Guidelines ................................................. 27
6.2 ESD Ratings.............................................................. 4 10.2 Layout Example .................................................... 28
6.3 Recommended Operating Conditions....................... 4 11 Device and Documentation Support ................. 29
6.4 Thermal Information .................................................. 5 11.1 Device Support...................................................... 29
6.5 Electrical Characteristics – 3.3 V .............................. 5 11.2 Related Documentation......................................... 29
6.6 Electrical Characteristics – 5 V ................................. 5 11.3 Receiving Notification of Documentation Updates 29
6.7 Electrical Characteristics – 12 V ............................... 6 11.4 Community Resources.......................................... 29
6.8 Electrical Characteristics – All Output Voltage 11.5 Trademarks ........................................................... 29
Versions ..................................................................... 6 11.6 Electrostatic Discharge Caution ............................ 29
6.9 Typical Characteristics .............................................. 7 11.7 Glossary ................................................................ 29
7 Detailed Description ............................................ 10 12 Mechanical, Packaging, and Orderable
7.1 Overview ................................................................. 10 Information ........................................................... 29
7.2 Functional Block Diagram ....................................... 10 12.1 DAP (VSON Package) .......................................... 29
7.3 Feature Description................................................. 10
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision J (April 2013) to Revision K Page
• Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................. 1
• Removed all references to Computer Design Software LM267X Made Simple (Version 6.0).............................................. 1
Changes from Revision I (April 2013) to Revision J Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 26
2 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LM2670

LM2670
www.ti.com SNVS036K – APRIL 2000 – REVISED JUNE 2016
5 Pin Configuration and Functions
KTW Package
7-Pin TO-263 NDZ Package
Top View 7-Pin TO-220
Top View
Not to scale
7 ON/OFF
Thermal
Pad 6 Feedback/FB
5 SYNC
4 GND
3 CBOOST/CB
2 Input
1
2
3
4
5
6
7
1 Switch_output
Not to scale
Switch_output
Input
CBOOST/CB
GND
SYNC
Feedback/FB
ON/OFF
NHM Package
14-Pin VSON
Top View
NC 1 14 Switch_output
Input 2 13 Switch_output
Input 3 12 Switch_output
CBOOST/CB 4 DAP 11 NC
NC 5 10 NC
SYNC 6 9 GND
Feedback/FB 7 8 ON/OFF
Not to scale
Connect DAP to pin 9 on PCB
Pin Functions
PIN
TO-263, I/O DESCRIPTION
NAME VSON
TO-220
Source pin of the internal High Side FET. This is a switching node. Attached this pin to
Switch output 1 12, 13, 14 O
an inductor and the cathode of the external diode.
Supply input pin to collector pin of high side FET. Connect to power supply and input
Input 2 2, 3 I bypass capacitors CIN. Path from VIN pin to high frequency bypass CIN and GND must
be as short as possible.
Boot-strap capacitor connection for high-side driver. Connect a high-quality, 100-nF
CBOOST/CB 3 4 I
capacitor from CB to VSW Pin.
Power ground pins. Connect to system ground. Ground pins of CIN and COUT. Path to
GND 4 9 —
CIN must be as short as possible.
Synchronization pin. Use this pin to synchronize the frequency to an external clock.
SYNC 5 6 I
The external frequency must be higher than the LM2670 internal oscillation frequency.
Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for
Feedback/FB 6 7 I ADJ version or connect this pin directly to the output capacitor for a fixed output
version.
Enable input to the voltage regulator. High = ON and low = OFF. Pull this pin high or
ON/OFF 7 8 I
float to enable the regulator.
NC — 1, 5, 10, 11 — No connect pins
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 3

LM2670
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
See
MIN MAX UNIT
Input supply voltage 45 V
Soft-start pin voltage –0.1 6 V
Switch voltage to ground (3) –1 VIN V
Boost pin voltage VSW + 8 V
Feedback pin voltage –0.3 14 V
Power dissipation Internally Limited
Wave, 4 s 260
Soldering temperature Infrared, 10 s 240 °C
Vapor phase, 75 s 219
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The absolute maximum specification of the Switch Voltage to Ground applies to DC voltage. An extended negative voltage limit of –10 V
applies to a pulse of up to 20 ns, –6 V of 60 ns and –3 V of up to 100 ns.
6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2) ±2000 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) ESD was applied using the human-body model, a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin.
6.3 Recommended Operating Conditions

MIN MAX UNIT
Supply voltage 8 40 V
Junction temperature, TJ –40 125 °C

LM2670
6.4 Thermal Information

LM2678
THERMAL METRIC (1) NDZ (TO-220) KTW (TO-263) NHM (VSON) UNIT
7 PINS 7 PINS 14 PINS
(2)
See 65 — —
(3)
See 45 — —
(4)
See — 56 —
(5)
RθJA Junction-to-ambient thermal resistance See — 35 — °C/W
(6)
See — 26 —
(7)
See — — 55
(8)
See — — 29
RθJC(top) Junction-to-case (top) thermal resistance 2 2 — °C/W
(1) For more information about traditional and new thermal metrics, see the application report, Semiconductor and IC Package Thermal
Metrics.
(2) Junction to ambient thermal resistance (no external heat sink) for the 7-lead TO-220 package mounted vertically, with ½ inch leads in a
socket, or on a PCB with minimum copper area.
(3) Junction to ambient thermal resistance (no external heat sink) for the 7-lead TO-220 package mounted vertically, with ½ inch leads
soldered to a PCB containing approximately 4 square inches of (1 oz.) copper area surrounding the leads.
(4) Junction to ambient thermal resistance for the 7-lead DDPAK mounted horizontally against a PCB area of 0.136 square inches (the
same size as the DDPAK package) of 1 oz (0.0014 in thick) copper.
(5) Junction to ambient thermal resistance for the 7-lead DDPAK mounted horizontally against a PCB area of 0.4896 square inches (3.6
times the area of the DDPAK package) of 1 oz (0.0014 in thick) copper.
(6) Junction to ambient thermal resistance for the 7-lead DDPAK mounted horizontally against a PCB copper area of 1.0064 square inches
(7.4 times the area of the DDPAK 3 package) of 1 oz (0.0014 in thick) copper. Additional copper area will reduce thermal resistance
further.
(7) Junction to ambient thermal resistance for the 14-lead VSON mounted on a PCB copper area equal to the die attach paddle.
(8) Junction to ambient thermal resistance for the 14-lead VSON mounted on a PCB copper area using 12 vias to a second layer of copper
equal to die attach paddle. Additional copper area will reduce thermal resistance further. For layout recommendations, see Application
Note AN-1187 Leadless Leadfram Package (LLP).
6.5 Electrical Characteristics – 3.3 V

Specifications apply for TA = TJ = 25°C unless otherwise noted. RADJ = 5.6 kΩ.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
3.234 3.3 3.366
VIN = 8 V to 40 V,
VOUT Output voltage over the entire junction temperature V
100 mA ≤ IOUT ≤ 5 A 3.201 3.399
range of operation –40°C to 125°C
η Efficiency VIN = 12 V, ILOAD = 5 A 86%
(1) All room temperature limits are 100% tested during production with TA = TJ = 25°C. All limits at temperature extremes are specified
through correlation using standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level
(AOQL).
(2) Typical values are determined with TA = TJ = 25°C and represent the most likely norm.
6.6 Electrical Characteristics – 5 V

4.9 5 5.1
VIN = 8 V to 40 V,
100 mA ≤ IOUT ≤ 5 A 4.85 5.15
(AOQL).

LM2670
6.7 Electrical Characteristics – 12 V

11.76 12 12.24
VIN = 15 V to 40 V,
100 mA ≤ IOUT ≤ 5 A 11.64 12.36
(AOQL).
6.8 Electrical Characteristics – All Output Voltage Versions

Specifications are for TA = TJ = 25°C unless otherwise specified. Unless otherwise specified VIN = 12 V for the 3.3 V, 5 V and
Adjustable versions, and VIN = 24 V for the 12 V version.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DEVICE PARAMETERS
VFEEDBACK = 8 V for 3.3-V, 5-V, and ADJ versions,
IQ Quiescent current 4.2 6 mA
VFEEDBACK = 15 V for 12-V Versions
50 100
Standby quiescent
ISTBY ON/OFF pin = 0 V over the entire junction temperature µA
current 150
3.8 4.5 5.25
ICL Current limit over the entire junction temperature range of operation A
3.6 5.4
–40°C to 125°C
Output leakage VIN = 40 V, VSWITCH = 0 V 200 µA
IL
current soft-start pin = 0 V VSWITCH = –1 V 16 15 mA
0.15 0.17
RDS(ON) Switch ON-resistance ISWITCH = 5 A over the entire junction temperature Ω
0.29
260
Measured at
fO Oscillator frequency over the entire junction temperature kHz
switch pin 225 280
Maximum duty cycle 91%
D Duty cycle
Minimum duty cycle 0%
IBIAS Feedback bias current VFEEDBACK = 1.3 V, ADJ version only 85 nA
1.4
ON/OFF threshold
VON/OFF over the entire junction temperature range of operation V
voltage 0.8 2
–40°C to 125°C
20
ION/OFF ON/OFF input current ON/OFF pin = 0 V over the entire junction temperature µA
45
Synchronization
FSYNC VSYNC (pin 5) = 3.5 V, 50% duty cycle 400 kHz
frequency
SYNC threshold
VSYNC 1.4 V
voltage

LM2670
6.9 Typical Characteristics
Figure 1. Normalized Output Voltage Figure 2. Line Regulation
Figure 3. Efficiency vs Input Voltage Figure 4. Efficiency vs ILOAD
Figure 5. Switch Current Limit Figure 6. Operating Quiescent Current

LM2670
Typical Characteristics (continued)
Figure 7. Standby Quiescent Current Figure 8. ON/OFF Threshold Voltage
Figure 9. ON/OFF Pin Current (Sourcing) Figure 10. Switching Frequency
Continuous Mode Switching Waveforms VIN = 20 V, VOUT = 5 V,

ILOAD = 3 A, L = 33 µH, COUT = 200 µF, COUTESR = 26 mΩ
A: VSW Pin Voltage, 10 V/div
B: Inductor Current, 1 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled
Figure 11. Feedback Pin Bias Current Figure 12. Horizontal Time Base: 1 µs/div

LM2670
Typical Characteristics (continued)
Load Transient Response for Continuous Mode VIN = 20 V,

Discontinuous Mode Switching Waveforms VIN = 20 V, VOUT = 5 V L = 33 µH, COUT = 200 µF,
VOUT = 5 V, ILOAD = 500 mA L = 10 µH, COUT = 400 µF, COUTESR = 26 mΩ
COUTESR = 13 mΩ A: Output Voltage, 100 mV//div, AC-Coupled
A: VSW Pin Voltage, 10 V/div B: Load Current: 500-mA to 3-A Load Pulse
B: Inductor Current, 1 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled
Figure 13. Horizontal Time Base: 1 µs/div Figure 14. Horizontal Time Base: 100 µs/div
Load Transient Response for Discontinuous Mode VIN = 20 V, VOUT = 5 V, L = 10 µH, COUT = 400 µF, COUTESR = 13 mΩ
A: Output Voltage, 100 mV/div, AC-Coupled
B: Load Current: 200-mA to 3-A Load Pulse
Figure 15. Horizontal Time Base: 200 µs/div

LM2670
7 Detailed Description
7.1 Overview
The LM2670 provides all of the active functions required for a step-down (buck) switching regulator. The internal
power switch is a DMOS power MOSFET to provide power supply designs with high current capability, up to 3 A,
and highly efficient operation.
The design support WEBENCH, can also be used to provide instant component selection, circuit performance
calculations for evaluation, a bill of materials component list and a circuit schematic for LM2670.
7.2 Functional Block Diagram
* Active Inductor Patent Number 5,514,947

† Active Capacitor Patent Number 5,382,918
7.3 Feature Description

7.3.1 Switch Output
This is the output of a power MOSFET switch connected directly to the input voltage. The switch provides energy
to an inductor, an output capacitor, and the load circuitry under control of an internal pulse-width-modulator
(PWM). The PWM controller is internally clocked by a fixed 260-kHz oscillator. In a standard step-down
application the duty cycle (Time ON/Time OFF) of the power switch is proportional to the ratio of the power
supply output voltage to the input voltage. The voltage on pin 1 switches between VIN (switch ON) and below
ground by the voltage drop of the external Schottky diode (switch OFF).

LM2670
Feature Description (continued)

7.3.2 Input
The input voltage for the power supply is connected to pin 2. In addition to providing energy to the load the input
voltage also provides bias for the internal circuitry of the LM2670. For ensured performance the input voltage
must be in the range of 8 V to 40 V. For best performance of the power supply the input pin must always be
bypassed with an input capacitor located close to pin 2.
7.3.3 C Boost
A capacitor must be connected from pin 3 to the switch output, pin 1. This capacitor boosts the gate drive to the
internal MOSFET above VIN to fully turn it ON. This minimizes conduction losses in the power switch to maintain
high efficiency. The recommended value for C Boost is 0.01 µF.
7.3.4 Ground
This is the ground reference connection for all components in the power supply. In fast-switching, high-current
applications such as those implemented with the LM2670, TI recommends using a broad ground plane to
minimize signal coupling throughout the circuit.
7.3.5 SYNC
This input allows control of the switching clock frequency. If left open-circuited the regulator will be switched at
the internal oscillator frequency, between 225 kHz and 280 kHz. An external clock can be used to force the
switching frequency and thereby control the output ripple frequency of the regulator. This capability provides for
consistent filtering of the output ripple from system to system as well as precise frequency spectrum positioning
of the ripple frequency which is often desired in communications and radio applications. This external frequency
must be greater than the LM2670 internal oscillator frequency, which could be as high as 280 kHz, to prevent an
erroneous reset of the internal ramp oscillator and PWM control of the power switch. The ramp oscillator is reset
on the positive going edge of the sync input signal. TI recommends that the external TTL or CMOS compatible
clock (between 0 V and a level greater than 3 V) be AC-coupled to the sync input through a 100-pf capacitor and
a 1-kΩ resistor to ground at pin 5 as shown in Figure 21.
When the SYNC function is used, current limit frequency foldback is not active. Therefore, the device my not be
fully protected against extreme output short-circuit conditions. See Additional Application Information.
7.3.6 Feedback
This is the input to a two-stage high gain amplifier, which drives the PWM controller. It is necessary to connect
pin 6 to the actual output of the power supply to set the DC output voltage. For the fixed output devices (3.3-V, 5-
V, and 12-V outputs), a direct wire connection to the output is all that is required as internal gain setting resistors
are provided inside the LM2670. For the adjustable output version two external resistors are required to set the
DC output voltage. For stable operation of the power supply it is important to prevent coupling of any inductor
flux to the feedback input.
7.3.7 ON/OFF
This input provides an electrical ON/OFF control of the power supply. Connecting this pin to ground or to any
voltage less than 0.8 V will completely turn OFF the regulator. The current drain from the input supply when OFF
is only 50 µA. Pin 7 has an internal pull-up current source of approximately 20 µA and a protection clamp Zener
diode of 7 V to ground. When electrically driving the ON/OFF pin the high voltage level for the ON condition
should not exceed the 6-V absolute maximum limit. When ON/OFF control is not required pin 7 should be left
open circuited.

LM2670
7.4 Device Functional Modes

7.4.1 Shutdown Mode
The ON/OFF pin provides electrical ON and OFF control for the LM2670. When the voltage of this pin is lower
than 1.4 V, the device is shutdown mode. The typical standby current in this mode is 50 µA.
7.4.2 Active Mode

When the voltage of the ON/OFF pin is higher than 1.4 V, the device starts switching and the output voltage rises
until it reaches a normal regulation voltage.

LM2670
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information

8.1.1 Design Considerations
Power supply design using the LM2670 is greatly simplified by using recommended external components. A wide
range of inductors, capacitors and Schottky diodes from several manufacturers have been evaluated for use in
designs that cover the full range of capabilities (input voltage, output voltage, and load current) of the LM2670. A
simple design procedure using nomographs and component tables provided in this data sheet leads to a working
design with very little effort.
The individual components from the various manufacturers called out for use are still just a small sample of the
vast array of components available in the industry. While these components are recommended, they are not
exclusively the only components for use in a design. After a close comparison of component specifications,
equivalent devices from other manufacturers could be substituted for use in an application.
Important considerations for each external component and an explanation of how the nomographs and selection
tables were developed follows.
8.1.2 Inductor
The inductor is the key component in a switching regulator. For efficiency the inductor stores energy during the
switch ON time and then transfers energy to the load while the switch is OFF.
Nomographs are used to select the inductance value required for a given set of operating conditions. The
nomographs assume that the circuit is operating in continuous mode (the current flowing through the inductor
never falls to zero). The magnitude of inductance is selected to maintain a maximum ripple current of 30% of the
maximum load current. If the ripple current exceeds this 30% limit the next larger value is selected.
The inductors offered have been specifically manufactured to provide proper operation under all operating
conditions of input and output voltage and load current. Several part types are offered for a given amount of
inductance. Both surface mount and through-hole devices are available. The inductors from each of the three
manufacturers have unique characteristics.
• Renco: ferrite stick core inductors; benefits are typically lowest cost and can withstand ripple and transient
peak currents above the rated value. These inductors have an external magnetic field, which may generate
EMI.
• Pulse Engineering: powdered iron toroid core inductors; these also can withstand higher than rated currents
and, being toroid inductors, have low EMI.
• Coilcraft: ferrite drum core inductors; these are the smallest physical size inductors and are available only as
surface mount components. These inductors also generate EMI but less than stick inductors.
8.1.3 Output Capacitor

The output capacitor acts to smooth the DC output voltage and also provides energy storage. Selection of an
output capacitor, with an associated equivalent series resistance (ESR), impacts both the amount of output ripple
voltage and stability of the control loop.
The output ripple voltage of the power supply is the product of the capacitor ESR and the inductor ripple current.
The capacitor types recommended in the tables were selected for having low ESR ratings.
In addition, both surface mount tantalum capacitors and through-hole aluminum electrolytic capacitors are offered
as solutions.

LM2670
Application Information (continued)

Impacting frequency stability of the overall control loop, the output capacitance, in conjunction with the inductor,
creates a double pole inside the feedback loop. In addition the capacitance and the ESR value create a zero.
These frequency response effects together with the internal frequency compensation circuitry of the LM2670
modify the gain and phase shift of the closed-loop system.
As a general rule for stable switching regulator circuits it is desired to have the unity gain bandwidth of the circuit
to be limited to no more than one-sixth of the controller switching frequency. With the fixed 260-kHz switching
frequency of the LM2670, the output capacitor is selected to provide a unity gain bandwidth of 40 kHz maximum.
Each recommended capacitor value has been chosen to achieve this result.
In some cases multiple capacitors are required either to reduce the ESR of the output capacitor, to minimize
output ripple (a ripple voltage of 1% of VOUT or less is the assumed performance condition), or to increase the
output capacitance to reduce the closed loop unity gain bandwidth (to less than 40 kHz). When parallel
combinations of capacitors are required it has been assumed that each capacitor is the exact same part type.
The RMS current and working voltage (WV) ratings of the output capacitor are also important considerations. In a
typical step-down switching regulator, the inductor ripple current (set to be no more than 30% of the maximum
load current by the inductor selection) is the current that flows through the output capacitor. The capacitor RMS
current rating must be greater than this ripple current. The voltage rating of the output capacitor must be greater
than 1.3 times the maximum output voltage of the power supply. If operation of the system at elevated
temperatures is required, the capacitor voltage rating may be de-rated to less than the nominal room temperature
rating. Careful inspection of the manufacturer's specification for de-rating of working voltage with temperature is
important.
8.1.4 Input Capacitor

Fast changing currents in high current switching regulators place a significant dynamic load on the unregulated
power source. An input capacitor helps to provide additional current to the power supply as well as smooth out
input voltage variations.
Like the output capacitor, the key specifications for the input capacitor are RMS current rating and working
voltage. The RMS current flowing through the input capacitor is equal to one-half of the maximum DC load
current so the capacitor should be rated to handle this. Paralleling multiple capacitors proportionally increases
the current rating of the total capacitance. The voltage rating must also be selected to be 1.3 times the maximum
input voltage. Depending on the unregulated input power source, under light load conditions the maximum input
voltage could be significantly higher than normal operation. Consider when selecting an input capacitor.
The input capacitor must be placed very close to the input pin of the LM2670. Due to relative high current
operation with fast transient changes, the series inductance of input connecting wires or PCB traces can create
ringing signals at the input terminal which could possibly propagate to the output or other parts of the circuitry. It
may be necessary in some designs to add a small valued (0.1 µF to 0.47 µF) ceramic type capacitor in parallel
with the input capacitor to prevent or minimize any ringing.
8.1.5 Catch Diode

When the power switch in the LM2670 turns OFF, the current through the inductor continues to flow. The path for
this current is through the diode connected between the switch output and ground. This forward biased diode
clamps the switch output to a voltage less than ground. This negative voltage must be greater than –1 V so a low
voltage drop (particularly at high current levels) Schottky diode is recommended. Total efficiency of the entire
power supply is significantly impacted by the power lost in the output catch diode. The average current through
the catch diode is dependent on the switch duty cycle (D) and is equal to the load current times (1-D). Use of a
diode rated for much higher current than is required by the actual application helps to minimize the voltage drop
and power loss in the diode.
During the switch ON time the diode is reversed biased by the input voltage. The reverse voltage rating of the
diode must be at least 1.3 times greater than the maximum input voltage.
8.1.6 Boost Capacitor

The boost capacitor creates a voltage used to overdrive the gate of the internal power MOSFET. This improves
efficiency by minimizing the on resistance of the switch and associated power loss. For all applications, TI
recommends using a 0.01-µF, 50-V ceramic capacitor.

LM2670
Application Information (continued)

8.1.7 Sync Components
When synchronizing the LM2670 with an external clock it is recommended to connect the clock to pin 5 through
a series 100-pf capacitor and connect a 1-kΩ resistor to ground from pin 5. This RC network creates a short 100-
ns pulse on each positive edge of the clock to reset the internal ramp oscillator. The reset time of the oscillator is
approximately 300 ns.
8.1.8 Additional Application Information

When the output voltage is greater than approximately 6 V, and the duty cycle at minimum input voltage is
greater than approximately 50%, the designer should exercise caution in selection of the output filter
components. When an application designed to these specific operating conditions is subjected to a current limit
fault condition, it may be possible to observe a large hysteresis in the current limit. This can affect the output
voltage of the device until the load current is reduced sufficiently to allow the current limit protection circuit to
reset itself.
Under current limiting conditions, the LM267x is designed to respond in the following manner:
1. At the moment when the inductor current reaches the current limit threshold, the ON-pulse is immediately
terminated. This happens for any application condition.
2. However, the current limit block is also designed to momentarily reduce the duty cycle to below 50% to avoid
subharmonic oscillations, which could cause the inductor to saturate.
3. Thereafter, once the inductor current falls below the current limit threshold, there is a small relaxation time
during which the duty cycle progressively rises back above 50% to the value required to achieve regulation.
If the output capacitance is sufficiently large, it may be possible that as the output tries to recover, the output
capacitor charging current is large enough to repeatedly re-trigger the current limit circuit before the output has
fully settled. This condition is exacerbated with higher output voltage settings because the energy requirement of
the output capacitor varies as the square of the output voltage (½ CV2), thus requiring an increased charging
current.
A simple test to determine if this condition might exist for a suspect application is to apply a short circuit across
the output of the converter, and then remove the shorted output condition. In an application with properly
selected external components, the output recovers smoothly.
Practical values of external components that have been experimentally found to work well under these specific
operating conditions are COUT = 47 µF, L = 22 µH. It should be noted that even with these components, for a
device’s current limit of ICLIM, the maximum load current under which the possibility of the large current limit
hysteresis can be minimized is ICLIM / 2. For example, if the input is 24 V and the set output voltage is 18 V, then
for a desired maximum current of 1.5 A, the current limit of the chosen switcher must be confirmed to be at least
3 A.
Under extreme overcurrent or short-circuit conditions, the LM267X employs frequency foldback in addition to the
current limit. If the cycle-by-cycle inductor current increases above the current limit threshold (due to short circuit
or inductor saturation for example) the switching frequency is automatically reduced to protect the IC. Frequency
below 100 kHz is typical for an extreme short-circuit condition.

LM2670
8.2 Typical Applications

8.2.1 Typical Application for All Output Voltage Versions
Figure 16. Basic Circuit for All Output Voltage Versions
8.2.1.1 Design Requirements

Select the power supply operating conditions and the maximum output current and follow below procedures to
find the external components for LM2670
8.2.1.2 Detailed Design Procedure

Using the nomographs and tables in this data sheet (or use the available design software at www.ti.com) a
complete step-down regulator can be designed in a few simple steps.
Step 1: Define the power supply operating conditions:
• Required output voltage
• Maximum DC input voltage
• Maximum output load current
Step 2: Set the output voltage by selecting a fixed output LM2670 (3.3-V, 5-V, or 12-V applications) or determine
the required feedback resistors for use with the adjustable LM2670–ADJ
Step 3: Determine the inductor required by using one of the four nomographs, Figure 17 through Figure 20.
Table 3 provides a specific manufacturer and part number for the inductor.
Step 4: Using Table 5 and Table 6 (fixed output voltage) or Table 9 and Table 10 (adjustable output voltage),
determine the output capacitance required for stable operation. Table 1 or Table 2 provide the specific capacitor
type from the manufacturer of choice.
Step 5: Determine an input capacitor from Table 7 or Table 8 for fixed output voltage applications. Use Table 1
or Table 2 to find the specific capacitor type. For adjustable output circuits select a capacitor from Table 1 or
Table 2 with a sufficient working voltage (WV) rating greater than VIN max, and an RMS current rating greater
than one-half the maximum load current (2 or more capacitors in parallel may be required).
Step 6: Select a diode from Table 4. The current rating of the diode must be greater than ILOAD max and the
reverse voltage rating must be greater than VIN max.
Step 7: Include a 0.01-µF, 50-V capacitor for CBOOST in the design.

LM2670
Typical Applications (continued)

8.2.1.2.1 Capacitor Selection Guides
Table 1. Input and Output Capacitor Codes—Surface Mount

SURFACE MOUNT
CAPACITOR
REFERENCE AVX TPS SERIES SPRAGUE 594D SERIES KEMET T495 SERIES
CODE
C (µF) WV (V) Irms (A) C (µF) WV (V) Irms (A) C (µF) WV (V) Irms (A)
C1 330 6.3 1.15 120 6.3 1.1 100 6.3 0.82
C2 100 10 1.1 220 6.3 1.4 220 6.3 1.1
C3 220 10 1.15 68 10 1.05 330 6.3 1.1
C4 47 16 0.89 150 10 1.35 100 10 1.1
C5 100 16 1.15 47 16 1 150 10 1.1
C6 33 20 0.77 100 16 1.3 220 10 1.1
C7 68 20 0.94 180 16 1.95 33 20 0.78
C8 22 25 0.77 47 20 1.15 47 20 0.94
C9 10 35 0.63 33 25 1.05 68 20 0.94
C10 22 35 0.66 68 25 1.6 10 35 0.63
C11 — — — 15 35 0.75 22 35 0.63
C12 — — — 33 35 1 4.7 50 0.66
C13 — — — 15 50 0.9 — — —
Table 2. Input and Output Capacitor Codes—Through Hole

THROUGH HOLE
CAPACITOR
REFERENCE SANYO OS-CON SA SERIES SANYO MV-GX SERIES NICHICON PL SERIES PANASONIC HFQ SERIES
CODE
C (µF) WV (V) Irms (A) C (µF) WV (V) Irms (A) C (µF) WV (V) Irms (A) C (µF) WV (V) Irms (A)
C1 47 6.3 1 1000 6.3 0.8 680 10 0.8 82 35 0.4
C2 150 6.3 1.95 270 16 0.6 820 10 0.98 120 35 0.44
C3 330 6.3 2.45 470 16 0.75 1000 10 1.06 220 35 0.76
C4 100 10 1.87 560 16 0.95 1200 10 1.28 330 35 1.01
C5 220 10 2.36 820 16 1.25 2200 10 1.71 560 35 1.4
C6 33 16 0.96 1000 16 1.3 3300 10 2.18 820 35 1.62
C7 100 16 1.92 150 35 0.65 3900 10 2.36 1000 35 1.73
C8 150 16 2.28 470 35 1.3 6800 10 2.68 2200 35 2.8
C9 100 20 2.25 680 35 1.4 180 16 0.41 56 50 0.36
C10 47 25 2.09 1000 35 1.7 270 16 0.55 100 50 0.5
C11 — — — 220 63 0.76 470 16 0.77 220 50 0.92
C12 — — — 470 63 1.2 680 16 1.02 470 50 1.44
C13 — — — 680 63 1.5 820 16 1.22 560 50 1.68
C14 — — — 1000 63 1.75 1800 16 1.88 1200 50 2.22
C15 — — — — — — 220 25 0.63 330 63 1.42
C16 — — — — — — 220 35 0.79 1500 63 2.51
C17 — — — — — — 560 35 1.43 — — —
C18 — — — — — — 2200 35 2.68 — — —
C19 — — — — — — 150 50 0.82 — — —
C20 — — — — — — 220 50 1.04 — — —
C21 — — — — — — 330 50 1.3 — — —
C22 — — — — — — 100 63 0.75 — — —
C23 — — — — — — 390 63 1.62 — — —
C24 — — — — — — 820 63 2.22 — — —
C25 — — — — — — 1200 63 2.51 — — —

LM2670
8.2.1.2.2 Inductor Selection Guides

For Continuous Mode Operation
Table 3. Inductor Manufacturer Part Numbers

INDUCTOR RENCO PULSE ENGINEERING COILCRAFT
REFERENC INDUCTANCE CURRENT
E (µH) (A) SURFACE THROUGH SURFACE
THROUGH HOLE SURFACE MOUNT
NUMBER MOUNT HOLE MOUNT
L23 33 1.35 RL-5471-7 RL1500-33 PE-53823 PE-53823S DO3316-333
L24 22 1.65 RL-1283-22-43 RL1500-22 PE-53824 PE-53824S DO3316-223
L25 15 2 RL-1283-15-43 RL1500-15 PE-53825 PE-53825S DO3316-153
L29 100 1.41 RL-5471-4 RL-6050-100 PE-53829 PE-53829S DO5022P-104
L30 68 1.71 RL-5471-5 RL6050-68 PE-53830 PE-53830S DO5022P-683
L31 47 2.06 RL-5471-6 RL6050-47 PE-53831 PE-53831S DO5022P-473
L32 33 2.46 RL-5471-7 RL6050-33 PE-53932 PE-53932S DO5022P-333
L33 22 3.02 RL-1283-22-43 RL6050-22 PE-53933 PE-53933S DO5022P-223
L34 15 3.65 RL-1283-15-43 — PE-53934 PE-53934S DO5022P-153
L38 68 2.97 RL-5472-2 — PE-54038 PE-54038S —
L39 47 3.57 RL-5472-3 — PE-54039 PE-54039S —
L40 33 4.26 RL-1283-33-43 — PE-54040 PE-54040S —
L41 22 5.22 RL-1283-22-43 — PE-54041 P0841 —
L44 68 3.45 RL-5473-3 — PE-54044 — —
L45 10 4.47 RL-1283-10-43 — — P0845 DO5022P-103HC
Table 4. Schottky Diode Selection Table

REVERSE SURFACE MOUNT THROUGH HOLE
VOLTAGE
(V) 3A 5 A OR MORE 3A 5 A OR MORE
1N5820
20 SK32 — —
SR302
SK33 1N5821
30 MBRD835L —
30WQ03F 31DQ03
SK34 MBRB1545CT 1N5822 —
30BQ040 MBR340 MBR745
40 30WQ04F 31DQ04 80SQ045
6TQ045S
MBRS340
SR403 6TQ045
MBRD340
SK35 MBR350
50 or more — 31DQ05 —
30WQ05F
SR305

LM2670
8.2.1.3 Application Curves
Figure 17. LM2670 – 3.3 V Figure 18. LM2670 – 5 V
Figure 19. LM2670 – 12 V Figure 20. LM2670 – Adjustable
8.2.2 Fixed Output Voltage Application
Figure 21. Basic Circuit for Fixed Output Voltage Applications

LM2670


A system logic power supply bus of 3.3 V is to be generated from a wall adapter which provides an unregulated
DC voltage of 13 V to 16 V. The maximum load current is 2.5 A. Through-hole components are preferred.
Step 1: Operating conditions are:
• VOUT = 3.3 V
• VIN max = 16 V
• ILOAD max = 2.5 A
Step 2: Select an LM2670T-3.3. The output voltage will have a tolerance of ±2% at room temperature and ±3%
over the full operating temperature range.
Step 3: Use the nomograph for the 3.3-V device, Figure 17. The intersection of the 16 V horizontal line (VIN max)
and the 2.5 A vertical line (ILOAD max) indicates that L33, a 22-µH inductor, is required.
From Table 3, L33 in a through-hole component is available from Renco with part number RL-1283-22-43 or part
number PE-53933 from Pulse Engineering.
Step 4: Use Table 5 or Table 6 to determine an output capacitor. With a 3.3-V output and a 22-µH inductor there
are four through-hole output capacitor solutions with the number of same type capacitors to be paralleled and an
identifying capacitor code given. Table 1 or Table 2 provide the actual capacitor characteristics. Any of the
following choices will work in the circuit:
• 1 × 220-µF, 10-V Sanyo OS-CON (code C5)
• 1 × 1000-µF, 35-V Sanyo MV-GX (code C10)
• 1 × 2200-µF, 10-V Nichicon PL (code C5)
• 1 × 1000-µF, 35-V Panasonic HFQ (code C7)
Step 5: Use Table 7 or Table 8 to select an input capacitor. With 3.3-V output and 22 µH there are three
through-hole solutions. These capacitors provide a sufficient voltage rating and an rms current rating greater than
1.25 A (1/2 ILOAD max). Again using Table 1 or Table 2 for specific component characteristics the following
choices are suitable:
• 1 × 1000-µF, 63-V Sanyo MV-GX (code C14)
• 1 × 820-µF, 63-V Nichicon PL (code C24)
• 1 × 560-µF, 50-V Panasonic HFQ (code C13)
Step 6: From Table 4 a 3-A Schottky diode must be selected. For through-hole components 20-V rated diodes
are sufficient. and 2 part types are suitable:
• 1N5820
• SR302
Step 7: A 0.01-µF capacitor is used for CBOOST.
Table 5. Output Capacitors for Fixed Output Voltage Application—Surface Mount (1) (2)
SURFACE MOUNT
OUTPUT
INDUCTANCE (µH) AVX TPS SERIES SPRAGUE 594D SERIES KEMET T495 SERIES
VOLTAGE (V)
NO. C CODE NO. C CODE NO. C CODE
10 4 C2 3 C1 4 C4
15 4 C2 3 C1 4 C4
3.3
22 3 C2 2 C7 3 C4
33 2 C2 2 C6 2 C4
(1) No. represents the number of identical capacitor types to be connected in parallel
(2) C Code indicates the Capacitor Reference number in Table 1 or Table 2 for identifying the specific component from the manufacturer

LM2670
Table 5. Output Capacitors for Fixed Output Voltage Application—Surface Mount()() (continued)
SURFACE MOUNT
OUTPUT
VOLTAGE (V)
10 4 C2 4 C6 4 C4
15 3 C2 2 C7 3 C4
5 22 3 C2 2 C7 3 C4
33 2 C2 2 C3 2 C4
47 2 C2 1 C7 2 C4
10 4 C5 3 C6 5 C9
15 3 C5 2 C7 4 C8
22 2 C5 2 C6 3 C8
12 33 2 C5 1 C7 2 C8
47 2 C4 1 C6 2 C8
68 1 C5 1 C5 2 C7
100 1 C4 1 C5 1 C8
Table 6. Output Capacitors for Fixed Output Voltage Application—Through Hole (1) (2)
THROUGH HOLE
OUTPUT INDUCTANCE SANYO OS-CON SA
SANYO MV-GX SERIES NICHICON PL SERIES PANASONIC HFQ SERIES
VOLTAGE (V) (µH) SERIES
NO. C CODE NO. C CODE NO. C CODE NO. C CODE
10 1 C3 1 C10 1 C6 2 C6
15 1 C3 1 C10 1 C6 2 C5
3.3
22 1 C5 1 C10 1 C5 1 C7
33 1 C2 1 C10 1 C13 1 C5
10 2 C4 1 C10 1 C6 2 C5
15 1 C5 1 C10 1 C5 1 C6
5 22 1 C5 1 C5 1 C5 1 C5
33 1 C4 1 C5 1 C13 1 C5
47 1 C4 1 C4 1 C13 2 C3
10 2 C7 1 C5 1 C18 2 C5
15 1 C8 1 C5 1 C17 1 C5
22 1 C7 1 C5 1 C13 1 C5
12 33 1 C7 1 C3 1 C11 1 C4
47 1 C7 1 C3 1 C10 1 C3
68 1 C7 1 C2 1 C10 1 C3
100 1 C7 1 C2 1 C9 1 C1
Table 7. Input Capacitors for Fixed Output Voltage Application—Surface Mount (1) (2) (3)
SURFACE MOUNT
OUTPUT
VOLTAGE (V)
10 2 C5 1 C7 2 C8
15 3 C9 1 C10 3 C10
3.3
22 See (4) See (4) 2 C13 3 C12
(4)
33 See See (4) 2 C13 2 C12
(1) Assumes worst case maximum input voltage and load current for a given inductance value
(4) Check voltage rating of capacitors to be greater than application input voltage
LM2670
Table 7. Input Capacitors for Fixed Output Voltage Application—Surface Mount()()() (continued)
SURFACE MOUNT
OUTPUT
VOLTAGE (V)
10 2 C5 1 C7 2 C8
15 2 C5 1 C7 2 C8
5 22 3 C10 2 C12 3 C11
33 See (4) See (4) 2 C13 3 C12
47 See (4) See (4) 1 C13 2 C12
10 2 C7 2 C10 2 C7
15 2 C7 2 C10 2 C7
22 3 C10 2 C12 3 C10
12 33 3 C10 2 C12 3 C10
(4) (4)
47 See See 2 C13 3 C12
68 See (4) See (4) 2 C13 2 C12
100 See (4) See (4) 1 C13 2 C12
Table 8. Input Capacitors for Fixed Output Voltage Application—Through Hole (1) (2) (3)
THROUGH HOLE
OUTPUT INDUCTANCE SANYO OS-CON SA
SANYO MV-GX SERIES NICHICON PL SERIES PANASONIC HFQ SERIES
VOLTAGE (V) (µH) SERIES
10 1 C7 2 C4 1 C5 1 C6
15 1 C10 1 C10 1 C18 1 C6
3.3
22 See (4) See (4) 1 C14 1 C24 1 C13
33 See (4) See (4) 1 C12 1 C20 1 C12
10 1 C7 2 C4 1 C14 1 C6
15 1 C7 2 C4 1 C14 1 C6
5 22 See (4) See (4) 1 C10 1 C18 1 C13
33 See (4) See (4) 1 C14 1 C23 1 C13
47 See (4) See (4) 1 C12 1 C20 1 C12
10 1 C9 1 C10 1 C18 1 C6
15 1 C10 1 C10 1 C18 1 C6
22 1 C10 1 C10 1 C18 1 C6
12 33 See (4) See (4) 1 C10 1 C18 1 C6
47 See (4) See (4) 1 C13 1 C23 1 C13
68 See (4) See (4) 1 C12 1 C21 1 C12
(4)
100 See See (4) 1 C11 1 C22 1 C11
(1) Assumes worst case maximum input voltage and load current for a given inductance value
(4) Check voltage rating of capacitors to be greater than application input voltage

LM2670
8.2.3 Adjustable Output Voltage Application
Figure 22. Basic Circuit for Adjustable Output Voltage Applications


In this example, it is desired to convert the voltage from a two battery automotive power supply (voltage range of
20 V to 28 V, typical in large truck applications) to the 14.8-VDC alternator supply typically used to power
electronic equipment from single battery 12-V vehicle systems. The load current required is 2 A maximum. It is
also desired to implement the power supply with all surface mount components.
Step 1: Operating conditions are:
• VOUT = 14.8 V
• VIN maximum = 28 V
• ILOAD maximum = 2 A
Step 2: Select an LM2670S-ADJ. To set the output voltage to 14.9 V, two resistors need to be chosen (R1 and
R2 in Figure 22). For the adjustable device the output voltage is set by the following relationship:
where
• VFB is the feedback voltage of typically 1.21 V (1)
A recommended value to use for R1 is 1 kΩ. In this example then R2 is determined to be:
(2)
R2 = 11.23 kΩ
The closest standard 1% tolerance value to use is 11.3 kΩ
This is set the nominal output voltage to 14.88 V which is within 0.5% of the target value.
Step 3: To use the nomograph for the adjustable device, Figure 20, requires a calculation of the inductor Volt •
microsecond constant (E • T expressed in V • µS) from the following formula:
where
LM2670
• VSAT is the voltage drop across the internal power switch which is Rds(ON) times ILOAD (3)
In this example this would be typically 0.15 Ω × 2 A or 0.3 V and VD is the voltage drop across the forward
biased Schottky diode, typically 0.5 V. The switching frequency of 260 kHz is the nominal value to use to
estimate the ON time of the switch during which energy is stored in the inductor.
For this example E • T is found to be:
(4)
(5)
Using Figure 20, the intersection of 27 V • µS horizontally and the 2 A vertical line (ILOAD max) indicates that L38,
a 68-µH inductor, must be used.
From Table 3, L38 in a surface mount component is available from Pulse Engineering with part number PE-
54038S.
Step 4: Use Table 9 or Table 10 to determine an output capacitor. With a 14.8-V output the 12.5 to 15 V row is
used and with a 68-µH inductor there are three surface mount output capacitor solutions. Table 1 or Table 2
provides the actual capacitor characteristics based on the C Code number. Any of the following choices can be
used:
• 1 × 33-µF, 20-V AVX TPS (code C6)
• 1 × 47-µF, 20-V Sprague 594 (code C8)
• 1 × 47-µF, 20-V Kemet T495 (code C8)
NOTE
When using the adjustable device in low voltage applications (less than 3-V output), if the
nomograph, Figure 20, selects an inductance of 22 µH or less, Table 9 and Table 10 do
not provide an output capacitor solution. With these conditions the number of output
capacitors required for stable operation becomes impractical. TI recommends using either
a 33-µH or 47-µH inductor and the output capacitors from Table 9 or Table 10.
Step 5: An input capacitor for this example will require at least a 35-V WV rating with an RMS current rating of 1
A (1/2 IOUT max). From Table 1 or Table 2 it can be seen that C12, a 33-µF, 35-V capacitor from Sprague, has
the required voltage and current rating of the surface mount components.
Step 6: From Table 4 a 3-A Schottky diode must be selected. For surface mount diodes with a margin of safety
on the voltage rating one of five diodes can be used:
• SK34
• 30BQ040
• 30WQ04F
• MBRS340
• MBRD340
Step 7: A 0.01-µF capacitor is used for CBOOST.

LM2670
Table 9. Output Capacitors for Adjustable Output Voltage Applications—Surface Mount (1) (2)
SURFACE MOUNT
INDUCTANCE
OUTPUT VOLTAGE (V) AVX TPS SERIES SPRAGUE 594D SERIES KEMET T495 SERIES
(µH)
33 (3) 7 C1 6 C2 7 C3
1.21 to 2.5
47 (3) 5 C1 4 C2 5 C3
33 (3) 4 C1 3 C2 4 C3
2.5 to 3.75
47 (3) 3 C1 2 C2 3 C3
22 4 C1 3 C2 4 C3
3.75 to 5 33 3 C1 2 C2 3 C3
47 2 C1 2 C2 2 C3
22 3 C2 1 C3 3 C4
33 2 C2 2 C3 2 C4
5 to 6.25
47 2 C2 2 C3 2 C4
68 1 C2 1 C3 1 C4
22 3 C2 1 C4 3 C4
33 2 C2 1 C3 2 C4
6.25 to 7.5
47 1 C3 1 C4 1 C6
68 1 C2 1 C3 1 C4
33 2 C5 1 C6 2 C8
47 1 C5 1 C6 2 C8
7.5 to 10
68 1 C5 1 C6 1 C8
100 1 C4 1 C5 1 C8
33 1 C5 1 C6 2 C8
47 1 C5 1 C6 2 C8
10 to 12.5
68 1 C5 1 C6 1 C8
100 1 C5 1 C6 1 C8
33 1 C6 1 C8 1 C8
47 1 C6 1 C8 1 C8
12.5 to 15
68 1 C6 1 C8 1 C8
100 1 C6 1 C8 1 C8
33 1 C8 1 C10 2 C10
47 1 C8 1 C9 2 C10
15 to 20
68 1 C8 1 C9 2 C10
100 1 C8 1 C9 1 C10
33 2 C9 2 C11 2 C11
47 1 C10 1 C12 1 C11
20 to 30
68 1 C9 1 C12 1 C11
100 1 C9 1 C12 1 C11
10 4 C13 8 C12
15 3 C13 5 C12
22 2 C13 4 C12
30 to 37 No Values Available
33 1 C13 3 C12
47 1 C13 2 C12
68 1 C13 2 C12
(3) Set to a higher value for a practical design solution.

LM2670
Table 10. Output Capacitors for Adjustable Output Voltage Applications—Through Hole (1) (2)
THROUGH HOLE
OUTPUT VOLTAGE INDUCTANCE SANYO OS-CON SA PANASONIC HFQ
SANYO MV-GX SERIES NICHICON PL SERIES
(V) (µH) SERIES SERIES
33 (3) 2 C3 5 C1 5 C3 3 C
1.21 to 2.5
47 (3) 2 C2 4 C1 3 C3 2 C5
33 (3) 1 C3 3 C1 3 C1 2 C5
2.5 to 3.75
47 (3) 1 C2 2 C1 2 C3 1 C5
22 1 C3 3 C1 3 C1 2 C5
3.75 to 5 33 1 C2 2 C1 2 C1 1 C5
47 1 C2 2 C1 1 C3 1 C5
22 1 C5 2 C6 2 C3 2 C5
33 1 C4 1 C6 2 C1 1 C5
5 to 6.25
47 1 C4 1 C6 1 C3 1 C5
68 1 C4 1 C6 1 C1 1 C5
22 1 C5 1 C6 2 C1 1 C5
33 1 C4 1 C6 1 C3 1 C5
6.25 to 7.5
47 1 C4 1 C6 1 C1 1 C5
68 1 C4 1 C2 1 C1 1 C5
33 1 C7 1 C6 1 C14 1 C5
47 1 C7 1 C6 1 C14 1 C5
7.5 to 10
68 1 C7 1 C2 1 C14 1 C2
100 1 C7 1 C2 1 C14 1 C2
33 1 C7 1 C6 1 C14 1 C5
47 1 C7 1 C2 1 C14 1 C5
10 to 12.5
68 1 C7 1 C2 1 C9 1 C2
100 1 C7 1 C2 1 C9 1 C2
33 1 C9 1 C10 1 C15 1 C2
47 1 C9 1 C10 1 C15 1 C2
12.5 to 15
68 1 C9 1 C10 1 C15 1 C2
100 1 C9 1 C10 1 C15 1 C2
33 1 C10 1 C7 1 C15 1 C2
47 1 C10 1 C7 1 C15 1 C2
15 to 20
68 1 C10 1 C7 1 C15 1 C2
100 1 C10 1 C7 1 C15 1 C2
33 1 C7 1 C16 1 C2
47 1 C7 1 C16 1 C2
68 1 C7 1 C16 1 C2
100 1 C7 1 C16 1 C2
10 1 C12 1 C20 1 C10
15 1 C11 1 C20 1 C11
22 1 C11 1 C20 1 C10
33 1 C11 1 C20 1 C10
47 1 C11 1 C20 1 C10
68 1 C11 1 C20 1 C10
(3) Set to a higher value for a practical design solution.
9 Power Supply Recommendations

The LM2670 is designed to operate from an input voltage supply up to 40 V. This input supply must be well
regulated and able to withstand maximum input current and maintain a stable voltage.

LM2670
10 Layout
10.1 Layout Guidelines

Board layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise may turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in
layout to minimize the effect of this switching noise. The most important layout rule is to keep the AC current
loops as small as possible. Figure 23 shows the current flow in a buck converter. The top schematic shows a
dotted line which represents the current flow during the top switch ON-state. The middle schematic shows the
current flow during the top switch OFF-state. The bottom schematic shows the currents referred to as ac
currents. These AC currents are the most critical because they are changing in a very short time period. The
dotted lines of the bottom schematic are the traces to keep as short and wide as possible. This also yields a
small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout
example. Best results are achieved if the placement of the LM2679 device, the bypass capacitor, the Schottky
diode, RFBB, RFBT, and the inductor are placed as shown in the example. Note that, in the layout shown, R1 =
RFBB and R2 = RFBT. TI also recommends using 2-oz. copper boards or heavier to help thermal dissipation and
to reduce the parasitic inductances of board traces. See application note AN-1229 SIMPLE SWITCHER® PCB
Layout Guidelines for more information.
Figure 23. Typical Current Flow on a Buck Converter

LM2670
10.2 Layout Example
Figure 24. Top Layer Foil Pattern of Printed-Circuit Board

LM2670
11 Device and Documentation Support
11.1 Device Support

11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Related Documentation

For related documentation see the following:
• AN-1187 Leadless Leadfram Package (LLP)
• AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines
11.3 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWITCHER is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
12.1 DAP (VSON Package)

The Die Attach Pad (DAP) can and must be connected to PCB Ground plane or island. For CAD and assembly
guidelines see Application Note AN-1187 at www.ti.com/lsds/ti/analog/powermanagement/power_portal.page.

PACKAGE OPTION ADDENDUM
www.ti.com 6-May-2022
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)
LM2670S-12/NOPB ACTIVE DDPAK/ KTW 7 45 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
TO-263 & Green S-12
LM2670S-3.3/NOPB ACTIVE DDPAK/ KTW 7 45 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
TO-263 & Green S-3.3
LM2670S-5.0 NRND DDPAK/ KTW 7 45 Non-RoHS Call TI Level-3-235C-168 HR -40 to 125 LM2670
LM2670S-5.0/NOPB ACTIVE DDPAK/ KTW 7 45 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
LM2670S-ADJ NRND DDPAK/ KTW 7 45 Non-RoHS Call TI Level-3-235C-168 HR -40 to 125 LM2670
TO-263 & Green S-ADJ
LM2670S-ADJ/NOPB ACTIVE DDPAK/ KTW 7 45 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
LM2670SD-12/NOPB ACTIVE VSON NHM 14 250 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002LB Samples
LM2670SD-3.3/NOPB ACTIVE VSON NHM 14 250 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002NB Samples
LM2670SD-5.0/NOPB ACTIVE VSON NHM 14 250 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002PB Samples
LM2670SD-ADJ/NOPB ACTIVE VSON NHM 14 250 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002RB Samples
LM2670SDX-3.3/NOPB ACTIVE VSON NHM 14 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002NB Samples
LM2670SDX-5.0/NOPB ACTIVE VSON NHM 14 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002PB Samples
LM2670SDX-ADJ/NOPB ACTIVE VSON NHM 14 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 S0002RB Samples
LM2670SX-12/NOPB ACTIVE DDPAK/ KTW 7 500 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
TO-263 & Green S-12
LM2670SX-3.3/NOPB ACTIVE DDPAK/ KTW 7 500 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
LM2670SX-5.0/NOPB ACTIVE DDPAK/ KTW 7 500 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
LM2670SX-ADJ/NOPB ACTIVE DDPAK/ KTW 7 500 RoHS-Exempt SN Level-3-245C-168 HR -40 to 125 LM2670 Samples
LM2670T-12/NOPB ACTIVE TO-220 NDZ 7 45 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2670 Samples
T-12
Addendum-Page 1
Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)
LM2670T-3.3/NOPB ACTIVE TO-220 NDZ 7 45 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2670 Samples
T-3.3
LM2670T-5.0/NOPB ACTIVE TO-220 NDZ 7 45 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2670 Samples
T-5.0
LM2670T-ADJ/NOPB ACTIVE TO-220 NDZ 7 45 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2670 Samples
T-ADJ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS TAPE DIMENSIONS

K0 P1
B0 W
Reel
Diameter
Cavity A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
W Overall width of the carrier tape
P1 Pitch between successive cavity centers
Reel Width (W1)

QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2 Q1 Q2
Q3 Q4 Q3 Q4 User Direction of Feed
Pocket Quadrants
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2670SD-12/NOPB VSON NHM 14 250 178.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SD-3.3/NOPB VSON NHM 14 250 178.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SD-5.0/NOPB VSON NHM 14 250 178.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SD-ADJ/NOPB VSON NHM 14 250 178.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SDX-3.3/NOPB VSON NHM 14 2500 330.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SDX-5.0/NOPB VSON NHM 14 2500 330.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SDX-ADJ/NOPB VSON NHM 14 2500 330.0 16.4 5.3 6.3 1.5 12.0 16.0 Q1
LM2670SX-12/NOPB DDPAK/ KTW 7 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
TO-263
LM2670SX-3.3/NOPB DDPAK/ KTW 7 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
TO-263
LM2670SX-5.0/NOPB DDPAK/ KTW 7 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
TO-263
LM2670SX-ADJ/NOPB DDPAK/ KTW 7 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
TO-263
Pack Materials-Page 1
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2670SD-12/NOPB VSON NHM 14 250 210.0 185.0 35.0
LM2670SD-3.3/NOPB VSON NHM 14 250 210.0 185.0 35.0
LM2670SD-5.0/NOPB VSON NHM 14 250 210.0 185.0 35.0
LM2670SD-ADJ/NOPB VSON NHM 14 250 210.0 185.0 35.0
LM2670SDX-3.3/NOPB VSON NHM 14 2500 367.0 367.0 35.0
LM2670SDX-5.0/NOPB VSON NHM 14 2500 367.0 367.0 35.0
LM2670SDX-ADJ/NOPB VSON NHM 14 2500 367.0 367.0 35.0
LM2670SX-12/NOPB DDPAK/TO-263 KTW 7 500 367.0 367.0 45.0
LM2670SX-3.3/NOPB DDPAK/TO-263 KTW 7 500 367.0 367.0 45.0
LM2670SX-5.0/NOPB DDPAK/TO-263 KTW 7 500 367.0 367.0 45.0
LM2670SX-ADJ/NOPB DDPAK/TO-263 KTW 7 500 367.0 367.0 45.0
TUBE
T - Tube
height L - Tube length
W - Tube
width
B - Alignment groove width

Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
LM2670S-12/NOPB KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-3.3/NOPB KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-5.0 KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-5.0 KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-5.0/NOPB KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-ADJ KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-ADJ KTW TO-263 7 45 502 25 8204.2 9.19
LM2670S-ADJ/NOPB KTW TO-263 7 45 502 25 8204.2 9.19
LM2670T-12/NOPB NDZ TO-220 7 45 502 30 30048.2 10.74
LM2670T-3.3/NOPB NDZ TO-220 7 45 502 30 30048.2 10.74
LM2670T-5.0/NOPB NDZ TO-220 7 45 502 30 30048.2 10.74
LM2670T-ADJ/NOPB NDZ TO-220 7 45 502 30 30048.2 10.74
MECHANICAL DATA
NDZ0007B
TA07B (Rev E)
www.ti.com
MECHANICAL DATA
KTW0007B
TS7B (Rev E)
BOTTOM SIDE OF PACKAGE
www.ti.com
MECHANICAL DATA
NHM0014A
SRC14A (Rev A)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated

Snvs 036 K

Uploaded by

Copyright:

Available Formats

Snvs 036 K

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Snvs 036 K

Uploaded by

Copyright:

Available Formats

Product Sample & Technical Tools & Support &

Folder Buy Documents Software Community

Changes from Revision J (April 2013) to Revision K Page

Changes from Revision I (April 2013) to Revision J Page

• Changed layout of National Data Sheet to TI format ........................................................................................................... 26

2 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

5 Pin Configuration and Functions

Connect DAP to pin 9 on PCB

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 3

6.2 ESD Ratings

6.3 Recommended Operating Conditions

4 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

6.4 Thermal Information

6.5 Electrical Characteristics – 3.3 V

6.6 Electrical Characteristics – 5 V

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 5

6.7 Electrical Characteristics – 12 V

6.8 Electrical Characteristics – All Output Voltage Versions

6 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

6.9 Typical Characteristics

Figure 1. Normalized Output Voltage Figure 2. Line Regulation

Figure 3. Efficiency vs Input Voltage Figure 4. Efficiency vs ILOAD

Figure 5. Switch Current Limit Figure 6. Operating Quiescent Current

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 7

Typical Characteristics (continued)

Figure 7. Standby Quiescent Current Figure 8. ON/OFF Threshold Voltage

Figure 9. ON/OFF Pin Current (Sourcing) Figure 10. Switching Frequency

Continuous Mode Switching Waveforms VIN = 20 V, VOUT = 5 V,

8 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

Typical Characteristics (continued)

Load Transient Response for Continuous Mode VIN = 20 V,

Figure 15. Horizontal Time Base: 200 µs/div

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 9

7.2 Functional Block Diagram

* Active Inductor Patent Number 5,514,947

7.3 Feature Description

10 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

Feature Description (continued)

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 11

7.4 Device Functional Modes

7.4.2 Active Mode

12 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

8 Application and Implementation

8.1 Application Information

8.1.3 Output Capacitor

Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 13

Application Information (continued)

8.1.4 Input Capacitor

8.1.5 Catch Diode

8.1.6 Boost Capacitor

14 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated

Product Folder Links: LM2670

Application Information (continued)