Ic Motor MC14028BCP
Ic Motor MC14028BCP
Ic Motor MC14028BCP
BCD-To-Decimal Decoder
Binary-To-Octal Decoder
The MC14028B decoder is constructed so that an 8421 BCD code
on the four inputs provides a decimal (one–of–ten) decoded output,
while a 3–bit binary input provides a decoded octal (one–of–eight)
code output with D forced to a logic “0”. Expanded decoding such as http://onsemi.com
binary–to–hexadecimal (one–of–16), etc., can be achieved by using
other MC14028B devices. The part is useful for code conversion,
MARKING
address decoding, memory selection control, demultiplexing, or
DIAGRAMS
readout decoding.
16
• Diode Protection on All Inputs PDIP–16
• Supply Voltage Range = 3.0 Vdc to 18 Vdc P SUFFIX MC14028BCP
CASE 648 AWLYYWW
• Capable of Driving Two Low–power TTL Loads or One Low–power 1
Schottky TTL Load Over the Rated Temperature Range
• Positive Logic Design
16
• Low Outputs on All Illegal Input Combinations SOIC–16
• Similar to CD4028B. D SUFFIX
14028B
AWLYWW
CASE 751B
1
PIN ASSIGNMENT
Q4 1 16 VDD
Q2 2 15 Q3
Q0 3 14 Q1
Q7 4 13 B
Q9 5 12 C
Q5 6 11 D
Q6 7 10 A
VSS 8 9 Q8
TRUTH TABLE
D C B A Q9 Q8 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0
0 0 0 0 0 0 0 0 0 0 0 0 0 1
0 0 0 1 0 0 0 0 0 0 0 0 1 0
0 0 1 0 0 0 0 0 0 0 0 1 0 0
0 0 1 1 0 0 0 0 0 0 1 0 0 0
0 1 0 0 0 0 0 0 0 1 0 0 0 0
0 1 0 1 0 0 0 0 1 0 0 0 0 0
0 1 1 0 0 0 0 1 0 0 0 0 0 0
0 1 1 1 0 0 1 0 0 0 0 0 0 0
1 0 0 0 0 1 0 0 0 0 0 0 0 0
1 0 0 1 1 0 0 0 0 0 0 0 0 0
1 0 1 0 0 0 0 0 0 0 0 0 0 0
1 0 1 1 0 0 0 0 0 0 0 0 0 0
1 1 0 0 0 0 0 0 0 0 0 0 0 0
1 1 0 1 0 0 0 0 0 0 0 0 0 0
1 1 1 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 0 0 0 0 0 0 0 0 0 0
BLOCK DIAGRAM
10 A Q0 3
Q1 14
3-BIT Q2 2
BINARY 13 B Q3 15 OCTAL
8421 DECODED
INPUTS Q4 1 DECIMAL
BCD OUTPUTS
Q5 6 DECODED
INPUTS
OUTPUTS
12 C Q6 7
Q7 4
Q8 9
11 D Q9 5
VDD = PIN 16
VSS = PIN 8
http://onsemi.com
2
MC14028B
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Î
ÎÎÎÎÎ ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎ VDD
– 55C 25C 125C
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Characteristic Symbol Vdc Min Max Min Typ (4.) Max Min Max Unit
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Output Voltage “0” Level 5.0 — 0.05 — 0 0.05 — 0.05 Vdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Vin = VDD or 0 VOL 10 — 0.05 — 0 0.05 — 0.05
15 — 0.05 — 0 0.05 — 0.05
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎÎ
ÎÎÎ
Vin = 0 or VDD
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎ
“1” Level
ÎÎÎ
ÎÎÎ
VOH
5.0
10
4.95
9.95
—
—
4.95
9.95
5.0
10
—
—
4.95
9.95
—
—
Vdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
15 14.95 — 14.95 15 — 14.95 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Input Voltage “0” Level Vdc
(VO = 4.5 or 0.5 Vdc) 5.0 — 1.5 — 2.25 1.5 — 1.5
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
VIL
(VO = 9.0 or 1.0 Vdc) 10 — 3.0 — 4.50 3.0 — 3.0
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
(VO = 13.5 or 1.5 Vdc) 15 — 4.0 — 6.75 4.0 — 4.0
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
“1” Level Vdc
(VO = 0.5 or 4.5 Vdc) 5.0 3.5 — 3.5 2.75 — 3.5 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
VIH
(VO = 1.0 or 9.0 Vdc) 10 7.0 — 7.0 5.50 — 7.0 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
(VO = 1.5 or 13.5 Vdc) 15 11 — 11 8.25 — 11 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Output Drive Current mAdc
(VOH = 2.5 Vdc) Source 5.0 – 3.0 — – 2.4 – 4.2 — – 1.7 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
(VOH = 4.6 Vdc) IOH 5.0 – 0.64 — – 0.51 – 0.88 — – 0.36 —
(VOH = 9.5 Vdc) 10 – 1.6 — – 1.3 – 2.25 — – 0.9 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎÎ
(VOH = 13.5 Vdc)
ÎÎÎÎÎÎÎÎÎÎ ÎÎÎ
ÎÎÎÎ
(VOL = 0.4 Vdc) ÎÎÎ
ÎÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎ
ÎÎÎSink
15
5.0
– 4.2
0.64
—
—
– 3.4
0.51
– 8.8
0.88
—
—
– 2.4
0.36
—
— mAdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
(VOL = 0.5 Vdc) IOL 10 1.6 — 1.3 2.25 — 0.9 —
(VOL = 1.5 Vdc) 15 4.2 — 3.4 8.8 — 2.4 —
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
Input Current
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ Iin 15 — ± 0.1 — ±0.00001 ± 0.1 — ± 1.0 µAdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ
(Vin = 0) ÎÎÎ
Input Capacitance
ÎÎÎ ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎ
ÎÎÎ
Cin — — — — 5.0 7.5 — — pF
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ ÎÎÎ
Quiescent Current
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ ÎÎÎ ÎÎÎÎ
ÎÎÎ
(Per Package)
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ ÎÎÎ
ÎÎÎ
ÎÎÎ
IDD 5.0
10
15
—
—
—
5.0
10
20
—
—
—
0.005
0.010
0.015
5.0
10
20
—
—
—
150
300
600
µAdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ ÎÎÎ
ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
Total Supply Current (5.) (6.)
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
(Dynamic plus Quiescent, ÎÎÎ
ÎÎÎ
IT 5.0
10
IT = (0.3 µA/kHz) f + IDD
IT = (0.6 µA/kHz) f + IDD
µAdc
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
Per Package) 15 IT = (0.9 µA/kHz) f + IDD
(CL = 50 pF on all outputs, all
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
buffers switching)
ÎÎÎ
4. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
5. The formulas given are for the typical characteristics only at 25C.
6. To calculate total supply current at loads other than 50 pF:
IT(CL) = IT(50 pF) + (CL – 50) Vfk
where: IT is in µA (per package), CL in pF, V = (VDD – VSS) in volts, f in kHz is input frequency, and k = 0.001.
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
SWITCHING CHARACTERISTICS (7.) (CL = 50 pF, TA = 25C)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
Characteristic Symbol VDD Min Typ (8.) Max Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
Output Rise and Fall Time
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ ÎÎÎÎ
ÎÎÎÎ ÎÎÎ
ÎÎÎÎ
ÎÎÎ
tTLH, tTHL = (1.5 ns/pF) CL + 25 ns
tTLH, tTHL = (0.75 ns/pF) CL + 12.5 ns
tTLH,
tTHL 5.0
10
—
—
100
50
200
100
ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ
ÎÎÎÎÎ ÎÎÎÎ
ÎÎÎÎ ÎÎÎÎ
ÎÎÎÎ
Propagation Delay Time ÎÎÎÎ
ÎÎÎÎ ÎÎÎ
tTLH, tTHL = (0.55 ns/pF) CL + 9.5 ns
ÎÎÎÎ
ÎÎÎ tPLH,
15 — 40 80
ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
tPLH, tPHL = (1.7 ns/pF) CL + 215 ns tPHL 5.0 — 300 600
tPLH, tPHL = (0.66 ns/pF) CL + 97 ns 10 — 130 260
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
tPLH, tPHL = (0.5 ns/pF) CL + 65 ns
7. The formulas given are for the typical characteristics only at 25C.
15 — 90
8. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
180
http://onsemi.com
3
MC14028B
20 ns 20 ns
Inputs B, C, and D VDD All outputs connected
switching in respect 90% to respective CL loads.
INPUT A 50%
to a BCD code. f in respect to a system
10%
VSS clock.
1/f
20 ns 20 ns
VDD
INPUT C 90%
50%
10%
VSS
Inputs A, B, and D low. tPLH tPHL
VOH
90%
Q4 50%
10%
VOL
tTLH tTHL
LOGIC DIAGRAM
Q0
Q1
A
Q2
Q3
B
Q4
Q5
C
Q6
Q7
D
Q8
Q9
http://onsemi.com
4
MC14028B
Excess–3
Excess–3
Inputs Output Numbers
Binary
Aiken
4–Bit
4–Bit
Gray
Gray
4221
D C B A 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1
0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 2 3 0 2 2
0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 3 2 0 3 3
0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 4 7 1 4 4
0 1 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 5 6 2 3
0 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 6 4 3 1 4
0 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 7 5 4 2
1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 8 15 5
1 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 9 14 6 5
1 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 10 12 7 9 6
1 0 1 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 11 13 8 5
1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 12 8 9 5 6
1 1 0 1 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 13 9 6 7 7
1 1 1 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 14 11 8 8 8
1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 15 10 7 9 9
http://onsemi.com
5
MC14028B
INPUTS
A B C D E F INHIBIT
(NO SELECTION)
A B C -D
MC14028B
Q0 Q9
A B C D A B C D A B C D A B C D A B C D A B C D A B C D A B C D
MC14028B MC14028B MC14028B MC14028B MC14028B MC14028B MC14028B MC14028B
Q0 Q9 Q0 Q9 Q0 Q9 Q0 Q9 Q0 Q9 Q0 Q9 Q0 Q9 Q0 Q9
0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63
*1/6 MC14069UB 64 OUTPUTS (SELECTED OUTPUT IS HIGH)
APPROPRIATE APPROPRIATE
Q0 VOLTAGE VOLTAGE
A Q1 NEON INCANDESCENT
Q2 DISPLAY DISPLAY
B Q3
Q4 OR
MC14028B Q5
C Q6
Q7 0
Q8 9 9 2 1 0
D Q9
http://onsemi.com
6
MC14028B
PACKAGE DIMENSIONS
PDIP–16
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08 NOTES:
–A– 1. DIMENSIONING AND TOLERANCING PER ANSI
ISSUE R Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
16 9 3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
B 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
1 8 5. ROUNDED CORNERS OPTIONAL.
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
F C A 0.740 0.770 18.80 19.55
L
B 0.250 0.270 6.35 6.85
S C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
SEATING F 0.040 0.70 1.02 1.77
–T– PLANE G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
H K M J 0.008 0.015 0.21 0.38
J K 0.110 0.130 2.80 3.30
G L 0.295 0.305 7.50 7.74
D 16 PL
M 0 10 0 10
0.25 (0.010) M T A M S 0.020 0.040 0.51 1.01
SOIC–16
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
–A– ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
16 9 2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
–B– MOLD PROTRUSION.
P 8 PL
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
1 8
0.25 (0.010) M B S PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
G
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
F A 9.80 10.00 0.386 0.393
K R X 45 B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
C F 0.40 1.25 0.016 0.049
–T– SEATING G 1.27 BSC 0.050 BSC
PLANE J J 0.19 0.25 0.008 0.009
M
K 0.10 0.25 0.004 0.009
D 16 PL M 0 7 0 7
P 5.80 6.20 0.229 0.244
0.25 (0.010) M T B S A S R 0.25 0.50 0.010 0.019
http://onsemi.com
7
MC14028B
PACKAGE DIMENSIONS
SOEIAJ–16
F SUFFIX
PLASTIC EIAJ SOIC PACKAGE
CASE 966–01
ISSUE O NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
16 9 LE MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
Q1 OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
E HE M 4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
1 8 L DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DETAIL P DIMENSION AT MAXIMUM MATERIAL CONDITION.
Z DAMBAR CANNOT BE LOCATED ON THE LOWER
D RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
VIEW P
e A MILLIMETERS INCHES
c DIM MIN MAX MIN MAX
A --- 2.05 --- 0.081
A1 0.05 0.20 0.002 0.008
b 0.35 0.50 0.014 0.020
c 0.18 0.27 0.007 0.011
A1 D 9.90 10.50 0.390 0.413
b E 5.10 5.45 0.201 0.215
e 1.27 BSC 0.050 BSC
0.13 (0.005) M 0.10 (0.004) HE 7.40 8.20 0.291 0.323
L 0.50 0.85 0.020 0.033
LE 1.10 1.50 0.043 0.059
M 0 10 0 10
Q1 0.70 0.90 0.028 0.035
Z --- 0.78 --- 0.031
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
EUROPE: LDC for ON Semiconductor – European Support JAPAN: ON Semiconductor, Japan Customer Focus Center
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET) 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Email: ONlit–german@hibbertco.com Phone: 81–3–5740–2745
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET) Email: r14525@onsemi.com
Email: ONlit–french@hibbertco.com
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT) ON Semiconductor Website: http://onsemi.com
Email: ONlit@hibbertco.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 For additional information, please contact your local
*Available from Germany, France, Italy, UK Sales Representative.
http://onsemi.com MC14028B/D
8