Irussor Aor 2021 Draft

DRAFT AOR
भारत सरकार
GOVERNMENT OF INDIA
रे ल मंत्रालय
MINISTRY OF RAILWAYS
भारतीय रे ल एकीकृ त मानक दर

अनुसूची
(फॉमेशन कायय ,पूल कायय एवं पी वे कायय )
Indian Railways
Unified Standard Schedule Of Rates
(Formation Works, Bridge Works and P.Way Works)
इं जीननयररग नवभाग
Engineering Department
2021
Draft IR Unified Standard Analysis of Rates - 2021 General and Operating Instructions
General and Operating Instructions

1. General Instructions:
1.1 These instructions & guidelines are applicable for all items included in all Chapters for Railway Formation Works, Bridge Works
and P. Way Works.
1.2 Cost of cement and reinforcement steels is not included in any item except where specifically mentioned otherwise in the item.
1.3 Design Mix Cement Concrete of all grades from M-15 to M-40 will be paid at same rate irrespective of grade mentioned in the
item. Grade mentioned is for guidance purpose. However, grade of RCC to be used at site shall be mentioned in the BOQ.
1.4 Automatic digital weigh Batching, mixing and placing, preferably mobile RMC plant shall be used for design mix concrete.
Concrete mixer shall be used for small quantity for nominal mix only with the permission of Engineer-in charge. Placement of
concrete shall be done by concrete pump in general.
1.5 Cost of Admixture (plasticizer / super-plasticizer) is included in the item of design mix concrete.
1.6 Payment for cement shall be made extra wherever mentioned in the item for the quantity as per approved design mix subjected to
minimum and maximum limit as prescribed in IS 456. For nominal mix and other misc items, it shall be as per standard
consumption enclosed separately with this USSOR.
1.7 Cost of shuttering, wherever required, shall be paid separately and is not included in the rate of item except where specifically
mentioned otherwise. Shuttering shall be paid only for the shuttering area coming in contact with the concrete surface.
1.8 For steel fabrication work, the cost of welding/riveting has been incorporated in the item rate and no addition on nominal weight of
the sections as specified in the drawings shall be applicable on account of welding/riveting. HSFG bolts, where used, shall be
payable.
1.9 The rate of an item includes:
(i) Cost of all labor, materials, tools & plants, machinery, transportation to the site of work, all lead & lift, handling, re-
handling, erection, testing, supervision & maintenance, unless mentioned specifically otherwise in the description of an
item, required for design, fabrication, execution and testing the work conforming to all applicable codes, specifications,
manuals and guidelines.
(ii) GST & other taxes, royalties, duties, cess, levies or any other fees that may be payable under any Central Government,
State Government or other Local Bodies Acts or Rules, mandatory insurance, profit etc.
1.10 Uniform rate of GST, apllicable for works contract, @12% has been adopted for all items while arriving at the Rate.
2. Operating Instructions
Numbering System Of SOR Items –
2.1 The system of numbering SOR items has been adopted for easy identification of item and linkage between item number &
description of item. Each Item number of SOR consists of 6 numeric digits, as detailed below:
2.1.1 First 2 digits (left side) indicate Chapter no. e.g. from 01 to 21.
2.1.2 Next one digit indicates Sub-Group within the Chapter.
2.1.3 Next 2 digits are Main Item nos. within one Sub-group.
2.1.4 Next one digit, i.e. right-most digit indicates Sub-item within the main item.
3. Units used in IRUSSOR

Wherever "Each" has been used as Unit in any item, it should be read in comjunction with the Description of the item. Short forms of
"Unit" are used as under at different places:
TRM Track Metre

RM Running Metre
CuCm Cubic Centimetre
CuDm Cubic Decimetre
Cum Cubic Metre
Sq Cm Square Centimetre
Sqm Square Metre
KM Kilometre
MT Metric Tonne
MT KM Metric Tonne Kilometre
Kg Kilogram
Draft IR Unified Standard Schedule of Rates - 2021 Basic Input Data Sheet
Indian Railways Unified Standard Schedule Of Rates (Formation Works, Bridge Works and P.Way Works)
"Basic Input Data Sheet"

for Rates Of Basic Items Used For 'Analysis Of Rates'
(Rates of the Basic Elements are without GST)

1. Rates of Basic Element shall necessarily be without GST as provision of the GST has been made in the Analysis of Rates of Items. Accordingly, it must
be ensured that Rates of basic elements to be entered in this "Basic Input Data Sheet" while updation of USSOR are exclusive of GST. Similarly hire -
charges of plant & machinery shall also be exclusive of GST. However hire Charges shall be inclusive of cost of services of operating staff, Cost of
lubricating oil, fuel and other consumables for running the plant and machinery unless othewise specified in the Description of the Basic Element.
2. For hire charges of plant machinery, per day means single shift of eight working hours.
SL Description Unit Rate Rate (Rs)

Code
Labour:
1 Draftsman / Surveyor Day 0001 1,500.00
2 Mate (Skilled) Day 0002 609.00
3 Mate (Semi skilled) Day 0003 505.00
4 Mason 1st class (Skilled) Day 0004 609.00
5 Mason 2nd class (Semi-skilled) Day 0005 505.00
6 Carpenter (Skilled) Day 0006 609.00
7 Carpenter (Semi skilled) Day 0007 505.00
8 Blacksmith - 1st Class (Skilled) Day 0008 609.00
9 Blacksmith - 2nd Class (Semi-skilled) Day 0009 505.00
10 Fitter Grade - 1 (Skilled) Day 0010 609.00
11 Fitter Grade - 2 (Semi-skilled) Day 0011 505.00
12 Painter (Skilled) Day 0012 609.00
13 Electrician (Skilled) Day 0013 609.00
14 Rock Excavator (Semi skilled) Day 0014 505.00
15 Rock Breaker (Semi skilled) Day 0015 505.00
16 Rock Hole Driller (Semi skilled) Day 0016 505.00
17 Stone Chiseller (Semi skilled) Day 0017 505.00
18 Highly Skilled labour Day 0018 714.00
19 Labour Skilled (For Steel Fabrication i.e. Machine Operator/Welder/Machinist etc.) Day 0019 609.00
20 Labour Unskilled Day 0020 431.00
21 Helper (Semi-skilled) Day 0021 505.00
22 Bandhani (Semi skilled) Day 0022 505.00
23 Bhisti (Semi skilled) Day 0023 505.00
24 Beldar (Semi Skilled) Day 0024 505.00
25 Beldar (Un skilled) Day 0025 431.00
26 Coolie (Un skilled) Day 0026 431.00
27 Mistry (Semi skilled) Day 0027 505.00
28 Grinderman (Skilled) Day 0028 609.00
29 Welder (Skilled) Day 0029 609.00
30 Chipper (Skilled) Day 0030 609.00
31 Luter (Skilled) Day 0031 609.00
32 Hammer man (Semi-skilled) Day 0032 505.00
33 Look Out Man (Un-skilled) Day 0033 431.00
34 Waterman (Un-skilled) Day 0034 431.00
35 Patrolman (Semi-skilled) Day 0035 505.00
36 Head Trolley man (Skilled) Day 0036 609.00
37 Trolly man (Semi-skilled) Day 0037 505.00
38 Caution man (Semi-skilled) Day 0038 505.00
39 Chowkidar (Semi skilled) Day 0039 505.00
40 Machinist (operator) (Skilled) Day 0040 609.00
41 Machine Operator (Machine) (Skilled) Day 0041 609.00
42 Track Machine Maintainer (Semi skilled) Day 0042 505.00
43 USFD Operator (With approved Certificate) Day 0043 1,500.00
Hire Charges:
44 Hire charges of Hydraulic Excavator (0.9 Cum Bucket Capacity) Day 0044 6,400.00


Code
45 Crawler mounted Hydraulic Excavator 200 HP (2.5 cum bucket) Day 0045 16,000.00
46 Hire charges of Vibratory Hammer attachment of Hydraulic Excavator for driving Sheet pile Day 0046 700.00
driving
47 Hire and running charges of front end loader (1.0 Cum bucket capacity) Day 0047 6,000.00
48 Hire and running charges of Tipper 12 Cum Capacity Day 0048 7,000.00
49 Hire and running charges of Tipper 12 Cum Capacity (without POL) Day 0049 2,500.00
50 Hire charges of Motor grader (3.35 metre blade) Hour 0050 2,450.00
51 Hire charges of Water tanker 5 to 6 KL capacity Hour 0051 150.00
52 Hire Charges of Vibratory roller 8 to 10 tonne Hour 0052 600.00
53 Hire charges of Road Roller 8 to10 tonnes Hour 0053 300.00
54 Hire Charges of Slope Vibrator to be attached to Hydralic Excavator for rolling of slope Day 0054 2,000.00
surfaces of embankment.
55 Hire Charges of Wet Mix Plant 60 TPH Capacity Hour 0055 950.00
56 Hire charges of dozer of 80 HP capacity Hour 0056 500.00
57 Hire charges of dozer 215 HP capacity Hour 0057 1,500.00
58 Hire Charges of JCB of 0.92 cum bucket Capacity Hour 0058 800.00
59 Hire Charges of Truck - 9 tonne (without POL ) Day 0059 2,000.00
60 Hire charges of Diesel Truck - 9 tonne Day 0060 3,940.00
61 Hire charges of Derrick Monkey Rope Day 0061 750.00
62 Hire and running charges of Tripod and Mechanical Winch machine complete with power unit Day 0062 3,000.00
and accessories etc. and shifting at site including maintenance and cost of fuel / lubricants &
operators for running
63 Hire and running charges of Hydraulic Piling Rig with power unit etc. including complete Day 0063 35,000.00
accessories and shifting at site
64 Hire and running charges of Bentonite pump Day 0064 3,000.00
65 Hire charges of air compressor 250 cfm capacity with two leads for pneumatic cutters / Day 0065 1,600.00
hammers
66 Hire Charges of Air compressor 500 Cfm for fabrication works Day 0066 1,700.00
67 Mobile Concrete Batching/Mixing Plant @ 20 cum/hour Hour 0067 1,400.00
68 Concrete Pump Hour 0068 900.00
69 Hire charges of Transit Mixer 4 cum capacity Hour 0069 2,140.00
70 Hire charges of Concrete Mixer 0.25 to 0.40 cubic metre capacity Day 0070 800.00
71 Hire charges of Generator 2.5 KVA (without POL) Day 0071 300.00
72 Hire charges of Generator 5 KVA (without POL) Day 0072 500.00
73 Hire charges of 7.5 KVA Generator Day 0073 1,000.00
74 Hire charges of 25 KVA Generator Day 0074 1,500.00
75 Hire charges for 3 phase generator (60 KVA) Day 0075 2,000.00
76 Hire Charges of Generator 100 KVA/125 KVA Day 0076 2,500.00
77 Hire charges of Generator of 250 KVA capacity Day 0077 3,000.00
78 Hire charges for Power pack with 200 litres capacity tank with 10 HP 3 phase induction mortar, Day 0078 5,265.00
inlet, out let valves pressure gauges, hose pipes etc for pushing arrangement including
consumables, tools, plants, operator, and transportation to site of work
79 Hire charges of Pin Vibrator Day 0079 350.00
80 Hire charges of surface vibrator Day 0080 300.00
81 Hire charges for tractor with trolley Day 0081 1,200.00
82 Hire charges of tractor with Ripper arrangement Day 0082 1,200.00
83 Hire charges of Power driven hammer drill Day 0083 1,500.00
84 Hire charges of Vibratory Hand Rammers / compactors Day 0084 450.00
85 Hire charges of cement / epoxy slurry injection machine Day 0085 600.00
86 Hire charges of pump set of capacity 4000 litre per hour Day 0086 900.00
87 Hire charges of 10MT crane with Grab Bucket of 0.75 cum capacity and accessories Day 0087 7,000.00
88 Hire and running charges of light crane 5 MT capacity Day 0088 4,000.00
89 Hire charges of Crane 10T capacity Day 0089 5,000.00
90 Hire charges of 12 MT Hydra Day 0090 5,000.00


Code
91 Hire charges of 12 MT crane and accessories Day 0091 6,000.00
92 Hiring charges of Crane 20 MT capacity Day 0092 8,000.00
93 Hiring and running charges of Crane 30 MT capacity including maintenance and cost of fuel / Day 0093 16,000.00
lubricants & operators for running
94 Hiring charges of Crane 50 MT capacity Day 0094 20,000.00
95 Hiring charges of 80MT capacity crane Day 0095 35,000.00
96 Hiring charges of 100 MT capacity crane Day 0096 50,000.00
102 Hiring of Trailor truck of 20 MT capacity Day 0102 18,000.00
103 Hire Charges of 20T truck with long Trailors (without POL) Day 0103 5,000.00
104 Hire charges of Hydraulic jack 8/10 Tonnes capacity Day 0104 300.00
105 Hire charges for jack of 40 MT lifting capacity Day 0105 800.00
106 Hire charges for jack of 100 MT lifting capacity Day 0106 2,000.00
107 Hire charges for 200 MT capacity Jack Day 0107 1,500.00
108 Hire charges of Camber Jacks etc. Day 0108 500.00
109 Hire charges of stressing jack with pump for stressing of HTS cables in PSC girders/slabs. Day 0109 11,500.00
110 Hire charges of grout pump with agitator and accessories Hour 0110 500.00
111 Pulse Echo Test (PET) for integrity testing of piles with contractor’s men, materials and Each 0111 2,000.00
machines. The rate includes cost of Inspection of site, preparation of pile head and any other
unforeseen cost required for the test, submission of reports in triplicate as per satisfaction of
the Engineer in Charge at site.
112 Hire Charges of Hydraulic Jack of 50 t capacity for lateral load testing of piles Day 0112 2,000.00
113 Hire Charges of Hydraulic Jack of 100 t capacity for lateral load testing of piles Day 0113 5,000.00
114 Hire charges for OEW flat jack of 100 tons capacity for longitudinal slewing of girder from both Each 0114 2,500.00
sides
115 Hire Charges of CNC gas cutting Machine Day 0115 4,500.00
116 Hire Charges of CNC drilling machine - 14 to 50mm dia, 100mm thickness, set of spindle - 2 Day 0116 14,000.00
sets, accuracy +/- 0.03mm.
117 Hire Charges of MMAW machine ( Manual Metal Arc Welding Machine) - 80 to 500 Amperes. Day 0117 25.00
118 Hire Charges of SAW machine - Tornado Make, current range - 150 to 1250 Amperes. Day 0118 7,500.00
119 Hire Charges of Angle grinder - 230mm dia. Disc, 6000 rpm, CP make. Day 0119 11.00
120 Hire Charges of Impact wrench - 32mm dia.Boit, CP Make. Day 0120 25.00
121 Hire Charges of Torque wrench - 150 kgf-m, Mekaster Make. Day 0121 10.00
122 Hire Charges of Power hack saw machine (Angle) Day 0122 25.00
123 Hire Charges of CNC end milling machine - (Horizonral Spindle), (1). Longitudinal Traverse of Day 0123 17,000.00
table (X-Axis) - 1500mm (2). Vertical Axis (Y-Axis) - 1000mm, (3).RAM Column Traverses (Z-
Axis) - 500mm.
124 Hire Charges of EOT, 10 ton Capacity, Reva Make Day 0124 1,500.00
125 Hire charges of Road Cum Rail vehicle for transporting Flash Butt Welding plant Day 0125 1,000.00
126 Hire Charges for Mobile Flash Butt Welding Plant Day 0126 55,000.00
128 Hire charges of USFD testing machine(B-Scan) Day 0128 2,500.00
129 Hire charges of USFD testing machine Day 0129 800.00
130 Hire changes for sand receiver and sand blasting pipes with gun and all accessories complete Day 0130 500.00
131 Hire charges for metalising gun with all accessories Day 0131 600.00
132 Hire charges of Arc Welding Machine 500 Amp Day 0132 300.00
133 Hire charges of gas cutter Day 0133 100.00
134 Hire charges of translamatic robotic welding machine Day 0134 5,000.00
135 Hire charges of Hot Paint machine Day 0135 150.00


Code
136 Hire charges of off Track Tamper Day 0136 300.00
137 Hire charges of Rail Drill Machine Day 0137 300.00
138 Hire charges for pillar drilling machine Day 0138 1,000.00
139 Hire charges of Electrically operated Rail Drilling Machine Day 0139 200.00
140 Hire charges of Concrete Sleeper Drilling Machine Day 0140 300.00
141 Hire charges of Electrically operated Rail Cutting Machine Day 0141 100.00
142 Hire charges of Rail Cutting Machine Day 0142 300.00
143 Hire charges of Abrasive Rail Cutter (without POL) Day 0143 300.00
144 Hire charges of Hydraulic Rail bender (Jim Crow) Day 0144 200.00
145 Hire charges of Heavy Duty Hydraulic Extractor (10 Tonnes) Day 0145 200.00
146 Hire charges of Hydraulic Rail tensor Day 0146 150.00
147 Hire charges of Hydraulic Sleeper Spacer Day 0147 200.00
148 Hire charges of Hammer Breaker Day 0148 200.00
149 Hire charges of Grinding Machine for 150 mm dia wheel Day 0149 300.00
150 Hire charges of Angle Grinder Day 0150 200.00
151 Hire charges of Rail Profile Weld Grinder Day 0151 100.00
152 Hire charges of Weld Trimmer Machine Day 0152 300.00
153 Hire charges of Mechanical Toe load measuring device Day 0153 200.00
154 Hire charges of Electronic Toe load measuring device Day 0154 200.00
155 Hire charges of Hydraulic bending machine to bend the rails including fuel and operator Day 0155 1,100.00
156 Hire charges of Furnace blower to heat the rails for bending purpose including fuel and Day 0156 300.00
operator
157 Hire charges for wood sawing machine including fuel and operator Day 0157 1,500.00
158 Hire charges of Jib crane attachable and detachable to BFR/BRH Day 0158 300.00
159 Hire charges of Portal Crane (with Fuel & Driver) Hour 0159 250.00
160 Hire charges of Insulated Rail Dolly Day 0160 20.00
161 Hire Charges of Inflatable emergency tower light 400 Watt Day 0161 50.00
162 Hire charges of boat with boatmen Day 0162 1,200.00
163 Hire charges of 3.0 m x 3.0 m waterproof Tent Day 0163 200.00
164 Hire charges of Chair Day 0164 15.00
165 Hire charges of Table Day 0165 50.00
166 Hire charges of Laptop / Computer with software & Printer Day 0166 300.00
167 Hire charges for plotter up to A0 size Day 0167 700.00
488 Hire Charges of Halogen Lamps 500 Watt Nos. 0488 40.00
168 Soil Quality Class SQ1 suitable for sub grade of embankment as per RDSO Specifications Cum 0168 75.00
RDSO/2020/GE: IRS-0004
171 Blasting Powder Kg 0171 50.00
172 Blasting Fuse (Fuse Wire) Each 0172 20.00
173 Bentonite powder MT 0173 4,025.00
174 Doob grass Sqm 0174 29.00
175 Sarkanda/ Sarpat Sqm 0175 45.00
176 Grass sods Sqm 0176 46.00
177 Non-woven Needle Punched and Mechanically or Thermally bonded type Geotextile for use as Sqm 0177 90.00
Separator/Filtration for Railway formation as per RDSO Specification No. RDSO/2018/GE:IRS-
0004 - Part Iwith minimum strengths in Grab test, Trapezoidal Tear test and Puncture test of
700N, 250 N and 1800 N respectively
178 Non-woven Needle Punched and Mechanically or Thermally bonded type Geotextile for use as Sqm 0178 170.00
Separator/Filtration for Railway formation as per RDSO Specification No. RDSO/2018/GE:IRS-
0004 - Part I with minimum strengths in Grab test, Trapezoidal Tear test and Puncture test of
1750N, 800 N and 5800 N respectively.


Code
179 Geo-composite drain consisting of Geonet Core sandwiched between Non-Woven geo textile Sqm 0179 450.00
filters on both sides as per RDSO Specification No. RDSO/2018/GE:IRS-0006
180 Mechanically woven double twisted hexagonal shaped wire mesh gabion boxes of required Cum 0180 1,495.00
sizes with 10mm x 12mm mesh of wire dia 2.7mm/3.7mm (ID/OD) and Zn & PVC coated
181 Diesel (HSD) Oil Litre 0181 101.62

182 Normal unleaded Petrol Litre 0182 105.00
183 Hydraulic oil SS-68 or equivalent of HPCL/BPCL/IOCL Litre 0183 100.00
184 Grease Graphite Grade 'O' (IS:408) Kg 0184 240.00
185 Kerosene Oil Litre 0185 56.00
186 Mobile Oil Litre 0186 250.00
187 Grease MP-2 or equivalent of HPCL/BPCL/IOCL Kg 0187 153.00
188 Ordinary Portland Cement 43 grade MT 0188 4,940.00
189 Ordinary Portland Cement 53 grade MT 0189 5,000.00
190 Pozzolana Portland Cement MT 0190 4,700.00
191 Sulphate Resisting Cement MT 0191 6,500.00
192 Plasticiser / Super Plasticiser Kg 0192 80.00
193 Admixture (anti shrinkage compound) for CC/RCC work Kg 0193 140.00
194 Synthetic polyester triangular fibre of length 6 mm, effective diameter 10-40 microns and Kg 0194 400.00
specific gravity of 1.34 to 1.40.
195 Waterproofing compound Kg 0195 207.00
196 Muriatic Acid Kg 0196 23.00
197 Surface protection material ESI Permaproof Litre 0197 253.00
198 Surface protection material ESI Permacil -GA Litre 0198 272.55
199 Surface protection material ESI Bond Litre 0199 278.30
200 Cost of filled bags including material as sand or earth for kentledge purpose. 1000 nos. 0200 5,000.00
201 Filled sand bags (30 kg weight) Each 0201 9.00
202 Coarse Sand (Zone III) Cum 0202 1,200.00
203 Fine Sand (Zone IV) Cum 0203 1,000.00
204 Screened Sand Kg 0204 2.50
205 Stone Aggregate (single size) 63mm nominal Cum 0205 900.00
206 Stone Aggregate (Single size) : 40 mm nominal size Cum 0206 754.00
210 Stone grit 6mm and down size or pea sized gravel Cum 0210 600.00
211 Crusher Screening(Quarry Dust) Conforming to Grading Zone - I to Zone- II Cum 0211 600.00
212 Production cost of Track Ballast in quarry including loading in truck Cum 0212 569.00
213 Stone boulder, weighing minimum 35 kg each Cum 0213 750.00
214 Stone Spalls Cum 0214 445.00
215 Filter media of stone aggregate confirming to RDSO specification (12 cum loose to be taken Cum 0215 1,200.00
as 10 cum after compaction)
216 Low relaxation H T Strands conforming to IS 14268 latest version for prestressed concrete MT 0216 57,000.00
217 CRCA Sheathing Metre 0217 165.00

218 HDPE Sheathing Metre 0218 275.00
219 Tube anchorage set complete with bearing plate , permanent wedges etc. Each 0219 1,320.00
220 MS round bar for reinforcement- average rate for various dia Quintal 0220 3,600.00
221 Thermo Mechanically Treated Bars grade Fe 500D - or more.(Average of dia 10mm to Quintal 0221 5,974.00
25mm) without GST
222 G.I. Binding wire Kg 0222 51.75
223 Structural Steel Plates conforming to Grade Designation E 250; Quality "A" as per IS 2062 Quintal 0223 6,300.00


Code
224 Structural steel such as T, Angles, Channels and R S Joists conforming to Grade Quintal 0224 4,950.00
Designation E 250; Quality "A" as per IS 2062
225 Structural steel plates conforming to Grade Designation E250; Quality "B0" as per IS:2062, Quintal 0225 7,330.00
Designation E250; Quality "B0" as per IS:2062,
227 tructural steel such as T, Angles, Channels and R S Joists conforming to Grade Designation Quintal 0227 5,860.00
E 250; Quality "C" as per IS 2062
Designation E250; Quality "BR" as per IS:2062,
229 Structural Steel such as T, Angles, Channels and R S Joists Grade Designation E350; Quintal 0229 6,000.00
Quality 'B0' as per IS 2062
230 M S Flat upto 10 mm thickness Quintal 0230 6,300.00
231 HSFG bolt with DTI Wasters conforming to IRS B1-2001 with latest Correction Slips Kg 0231 100.00
232 Mild steel rivets for steel girders Quintal 0232 6,540.00
233 Rivets (different sizes) for miscellaneous works. Kg 0233 54.50
234 Nut & Bolts with washers of all sizes Kg 0234 80.00
235 Holding down HTS bolts with plates, nuts etc. Quintal 0235 7,500.00
236 Cup Grinding Stone Each 0236 900.00
237 Drill Bit Each 0237 300.00
238 Electrodes for steel fabrication work Metre 0238 24.00
239 Welding Rod for Gas Metal Arc Welding Kg 0239 116.82
240 SAW Welding Wire Kg 0240 66.00
241 Flux for SAW Weldging Kg 0241 65.00
242 Cost of Drifts Each 0242 65.00
243 Cost of Service Bolts for assembling of Girders Each 0243 35.00
244 Shielding Gas (Co2) for fabrication works Kg 0244 69.00
245 Aluminum Sheet / Strips of various sizes & thickness Kg 0245 200.00
246 GI Sheet 1.50 mm thick Quintal 0246 4,600.00
247 Mild steel chequered plate MT 0247 42,500.00
248 Polyvinyl chloride sheet 400 micron. Sqm 0248 40.25
249 Z section sheet piles AZ 18-800 (Arcellor Mittal) or equivalent & bracing Quintal 0249 4,500.00
250 G.I. wire 4mm dia Kg 0250 70.00
251 MS Bolts & Nuts below 10mm dia Kg 0251 60.00
252 MS bolts & nuts more than 10 mm dia Quintal 0252 8,500.00
253 100mm channel shoulder 2.5 m long (Shuttering material) Each 0253 1,322.50
254 MS tube 40mm dia (Shuttering material) Metre 0254 293.25
255 Wall form Panel 1250mm x 450mm (Shuttering material) Each 0255 1,150.00
256 Adjustable telescopic prop 3m (2.02m-3.75m) (Shuttering material) Each 0256 1,265.00
257 Beam Clamp 300-380mm (450mm-1070mm) (Shuttering material) Set 0257 454.25
258 Cadmium plated full threaded steel screws (30mm x 4mm dia) (Shuttering material) 100 nos. 0258 35.65
259 Aluminium washer 2mm thick & 15 mm dia (Shuttering material) 100 nos. 0259 28.75
260 uPVC Pipe- type A ISI marked 110mm dia (working pressure 4Kg/cm2) Metre 0260 160.00
261 uPVC Pipe- type A ISI marked 160mm dia Metre 0261 350.00
262 GI Pipe 50 mm dia , B Class Medium duty Metre 0262 315.35
263 GI Pipe 100 mm dia , B Class Medium duty Metre 0263 731.55
264 Clamps and MS stays including bolts and nuts for 100mm dia pipe Each 0264 90.00
265 Clamps and MS stays including bolts and nuts for 50mm dia pipe Each 0265 53.00
266 C I grating 100mm x 100mm Each 0266 75.00
267 Etch primer as per IS: 5666 Litre 0267 340.00
268 Aluminium wire for spraying Kg 0268 219.93
269 Elastomeric bearing assembly consisting of 7 layers of Elastomer bonded to 6 nos. internal Each 0269 15,360.00
reinforcing steel laminates by the process of vulcanisation, complete with all components as
per drawing and Technical Specification (Each of 19200 Cu Cm)


Code
270 Cast steel rocker bearing assembly of 250 tonne design load capacity duly painted complete Each 0270 100,000.00
with all its components as per drawing and specifications
271 Forged steel roller bearing of 250 tonne design load capacity duly painted complete with all its Each 0271 150,000.00
components as per drawing and specifications
272 PTFE sliding plate bearing assembly of 80 tonnes design load capacity duly painted complete Each 0272 24,000.00
with all its components as per drawing and Technical Specifications
273 300 MT Capacity Pot Cum PTFE Bearing (Free end ) assembly consisting of a metal piston Each 0273 57,880.00
supported by a disc of un reinforced elastomer that is confined with in the metal cylinder and
sliding assembly comprising of stainless steel attached to metal backing plate sliding in
horizontal plane over PTFE confined in recess(s) on the piston with internal seal (Brass
laminated rings), hard facings, external seal & wiper seal etc complete with cast steel
assemblies/fabricated structural steel assemblies duly painted with all components complete
as per drawings and Technical Specifications.
274 300 MT Capacity Pot cum PTFE bearing (Fixed type) assembly consisting of a metal piston Each 0274 83,045.00
supported by un reinforced elastomer confined in the pot with brass ring sealing making with
cast steel assemblies/fabricated structural steel assemblies duly painted with all components
complete as per drawings and Technical Specifications.
275 300 MT capacity Pot Cum PTFE GUIDED (L) Bearing assembly consisting of a metal piston Each 0275 101,185.00
sliding assembly with guiding arrangement to bear and resist the horizontal force in the desired
direction comprising of stain less steel attached to metal backing plate sliding in horizontal
plane over PTFE confined in recess (s)on the piston with internal seal (Brass laminated
rings),hard facings, external seal & wiper seal etc complete with cast steel
276 300 MT capacity Pot Cum PTFE GUIDED(T) Bearing assembly consisting of a metal piston Each 0276 96,790.00
rings),hard facings ,external seal & wiper seal etc complete with cast steel
supported by a disc of unreinforced elastomer that is confined with in the metal cylinder and
sliding assembly comprising of stain less steel attached to metal backing plate sliding in
horizontal plane over PTFE confined in recess (s)on the piston with internal seal (Brass
laminated rings),hard facings ,external seal & wiper seal etc complete with cast steel
278 250 MT Capacity Pot type bearing (Fixed) assembly consisting of a metal piston supported by Each 0278 62,045.00
un reinforced elastomer confined in the pot with brass ring sealing making with cast steel
279 250 MT Capacity Pot Cum PTFE GUIDED(L)Bearing assembly consisting of a metal piston Each 0279 77,390.00
280 250MT Capacity Pot Cum PTFE GUIDED(T)Bearing assembly consisting of a metal piston Each 0280 72,695.00


Code
281 200 MT Capacity Pot Cum PTFE Bearing (Free end) assembly consisting of a metal piston Each 0281 36,655.00
282 200 MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston Each 0282 45,025.00
supported by un reinforced elastomer confined in the pot with brass ring sealing making with
cast steel assemblies/fabricated structural steel assemblies duly painted with all components
complete as per drawings and Technical Specifications.
283 200 MT Capacity Pot Cum PTFE GUIDED(L)Bearing assembly consisting of a metal piston Each 0283 57,140.00
284 200 MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal piston Each 0284 52,805.00
286 150MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston supported Each 0286 29,985.00
by un reinforced elastomer confined in the pot with brass ring sealing making with cast steel
287 150MT Capacity Pot Cum PTFE Guided (L) Bearing assembly consisting of a metal piston Each 0287 38,745.00
288 150MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal piston Each 0288 35,760.00
289 100MT Capacity Pot Cum PTFE Bearing (Free end ) assembly consisting of a metal piston Each 0289 16,350.00


Code
290 100MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston supported Each 0290 17,385.00
by un reinforced elastomer confined in the pot with brass ring sealing making with cast steel
291 100MT Capacity Pot Cum PTFE Guided (L) Bearing assembly consisting of a metal piston Each 0291 25,625.00
292 100MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal piston Each 0292 23,350.00
293 300 MT Capacity Spherical fixed bearing consists of an assembly of precision machined steel Each 0293 65,185.00
components with spherical concave and convex elements in its centre designed and sized
according the specific requirements .The bottom plate with a spherically concave top face
covered with a recessed PTFE sheet .The top component is a solid stainless steel plate with
spherically machined convex bottom face mating with concave curved surface fixed by
restraining rings to restrict the horizontal movement as a complete unit made up of with Mild
steel/cast iron steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030 Grade 280-
520W or 340-570W,AISI 304/316 shall be used for the backing plates with flat or curved
surfaces.
294 300 MT Capacity Spherical free float bearing consists of an assembly of precision machined Each 0294 55,860.00
steel components with spherical concave and convex elements in its centre designed and
sized according the specific requirements .The bottom plate with a spherically concave top
face covered with a recessed PTFE sheet .The top component is a solid stainless steel plate
with spherically machined convex bottom face mating with concave curved surface . Sliding
assembly attached consists of a polished stainless sheet welded to the under side of top steel
plate slides on PTFE disc recessed or bonded to the upper surface of convex plate as
complete unit made up of with Mild steel/cast iron steel/Stainless steel conforming to IS 2062
Grade -B & IS 1030 Grade 280-520W or 340-570W,AISI 304/316 shall be used for the backing
plates with flat or curved surfaces, Stainless sheet shall be in accordance with AISI316L OR of
IS 6911 of minimum thick 3mm
295 300 MT Capacity Spherical Slide Guide (L) bearing consists of an assembly of precision Each 0295 79,400.00
machined steel components with spherical concave and convex elements in its centre
designed and sized according the specific requirements .The bottom plate with a spherically
concave top face covered with a recessed PTFE sheet .The top component is a solid
stainless steel plate with spherically machined convex bottom face mating with concave
curved surface . Sliding assembly with guiding system bear and transmit the horizontal force in
one direction and allowing the movement perpendicular to above (Longitudinal direction)
consisting of a polished stainless sheet welded to the under side of top steel plate slides on
PTFE disc recessed or bonded to the upper surface of convex plate as complete unit made
up of with Mild steel/cast iron steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030
Grade 280-520W or 340-570W,AISI 304/316 shall be used for the backing plates with flat or
curved surfaces, Stainless sheet sha all respect as directed by the Engineer - in - charge.
Note: Rail cu


Code
296 300 MT Capacity Spherical Slide Guide (T) bearing consists of an assembly of precision Each 0296 75,560.00
designed and sized according the specific requirements .The bottom plate with a spherically
concave top face covered with a recessed PTFE sheet .The top component is a solid
stainless steel plate with spherically machined convex bottom face mating with concave
curved surface . Sliding assembly with guiding system bear and transmit the horizontal force in
one direction and allowing the movement perpendicular to above (Transverse direction)
consisting of a polished stainless sheet welded to the under side of top steel plate slides on
PTFE disc recessed or bonded to the upper surface of convex plate as complete unit made
up of with Mild steel/cast iron steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030
Grade 280-520W or 340-570W,AISI 304/316 shall be used for the backing plates with flat or
curved surfaces, Stainless sheet shall all respect as directed by the Engineer - in - charge.
Note: Rail
297 Single coil spring washer for bridge bearing for 36 mm dia bolts Each 0297 12.00
298 Hot melt Thermo plastic road marking paint Litre 0298 160.00
299 Luminous Paint as per RDSO's Spec. no. M&C/PCN/120-2011 Litre 0299 300.00
301 Bituminous Emulsion without Mica (IP no. 56192 and RDSO Specification no.P30-1996) Litre 0301 200.00
302 Solvent confirming to IS Specification 1745-1976. Litre 0302 150.00

303 High build epoxy paint (two pack) as per RDSO's Specn. No. M&C/PCN/111/88 Litre 0303 440.00
304 Anti-corrosive Bituminous Paint (Black) confirming to IS:9862 Litre 0304 80.00
305 Anti-corrosive Paint as per RDSO's Specn. No. M&C/PCN/123/2012 Litre 0305 280.00
306 Enamel Paint as per RDSO's Spec. no.M&C/PCN/120-2011 Litre 0306 190.00
307 Ready mix Zinc Chromate primer as per IS 104 Litre 0307 100.00
308 Zinc Chromate red oxide Primer to IS:2074 Litre 0308 130.00
309 Aluminium paint Litre 0309 160.00
310 Synthetic Enamel Paint in Black or Chocolate shade Litre 0310 220.00
311 Epoxy paint as per RDSO Spec M&C/PCN/123-11 Litre 0311 440.00
312 Ready Mixed Paint as per IS:13607 Litre 0312 230.00
313 Wire Brush - 25cm long Each 0313 15.00
314 Soft Brush for painting - 25cm long Each 0314 33.00
315 Paint Brush (writing) of any size Each 0315 150.00
316 Industrial grade blown type Petroleum Bitumen of grade 85/25 as per IS:702 MT 0316 47,000.00
317 Coal tar Emulsion Litre 0317 50.00
318 Bitumen emulsion for road of grade RS-1 confirming to IS 8887 MT 0318 37,000.00
319 Bitumen Hot sealing compound : Gr. A MT 0319 28,000.00
320 Synthetic Rubber based Adhesive Litre 0320 200.00
321 Epoxy for fixing HDPE dowel, Rubber Pads as per RDSO approved specification Kg 0321 500.00
322 Araldite GY257 Kg 0322 379.50
323 Epoxy Hardener HY850 Kg 0323 370.30
324 Paint Brush 100 mm Each 0324 90.00
328 Supply of complete assembly of strip seal expansion joint for 40mm expansion , comprising of Metre 0328 4,000.00
edge beams, anchorage, strip seal element and complete assembly as per approved
specification and drawings
329 Supply of complete assembly of strip seal expansion joint for 80mm expansion , comprising of Metre 0329 5,500.00
edge beams, anchorage, strip seal element and complete assembly as per approved
330 Supply of complete assembly of strip seal expansion joint for 120mm expansion , comprising Metre 0330 6,500.00
of edge beams, anchorage, strip seal element and complete assembly as per approved


Code
331 Supply of complete assembly of strip seal expansion joint for 160mm expansion , comprising Metre 0331 8,000.00
of edge beams, anchorage, strip seal element and complete assembly as per approved
332 Welding cable copper 50 mm2 Metre 0332 110.00
333 500 Amp Arc welding Electrode holder Each 0333 85.00
334 Welding & cutting torch Each 0334 950.00
335 Hand gloves leather set 0335 60.00
336 Welding Hose rubber for Oxygen/D.A. 6mm dia Metre 0336 28.00
337 Welding screen Each 0337 150.00
338 Welding by Electric Plant Cm 0338 1.00
339 Commercial LPG (in cylinder) Kg 0339 73.71
340 Oxygen Gas (in cylinder) Kg 0340 50.00
341 Acetylene Gas (in cylinder) Kg 0341 65.00
342 Pressure Regulator for Oxygen/Acetylene cylinder Each 0342 1,450.00
343 Hard Variety Jungle Wood blocks 10 Cudm 0343 350.00
344 2nd class deodar wood in scantling 10 Cudm 0344 465.00
345 Fuel wood Quintal 0345 4,000.00
346 Crack filling epoxy for guniting and pressure grouting work Kg 0346 650.00
347 Accelerator compound for guniting Kg 0347 140.00
348 GI/MS nipple size 20mm dia Each 0348 15.00
349 Pre-packed polymer concrete based on epoxy system complete with curing compound, Kg 0349 10.00
initiator and promoter
350 Epoxy mortar for concrete repair kg 0350 25.00
351 Epoxy resin hardener mix for seal coat Kg 0351 150.00
352 Acrylic polymer bonding coat Litre 0352 150.00
353 Pre packed cement based polymer mortar of strength 45 Mpa at 28 days Kg 0353 22.00
354 Wire mesh size 50mm x 50mm of 3mm wire Kg 0354 80.00
355 Wire mesh (Rabbit) Sqm 0355 67.20
356 Galvanised steel fibre Kg 0356 200.00
357 Galvanised chain link mesh netting of 80mm x 80mm mesh size Sqm 0357 180.00
358 Galvanised spiral lock spring Each 0358 19.20
359 Epoxy coated washer plate of 200mm x 200mm x 6mm size Each 0359 156.00
360 Anchor fastener of 10mm dia and 110mm length Each 0360 72.00
361 Bottom anchors of 16mm dia HYSD & 1m length Each 0361 276.00
362 Galvanised steel wire mesh rope net made of 9mm dia steel wire rope having aperture size of Sqm 0362 468.00
45cm x 60cm with 6m length hangs
363 NP 4 Class RCC pipe 300mm dia Metre 0363 600.00
364 NP 4 Class RCC pipe 450mm dia Metre 0364 950.00
365 NP 4 Class RCC pipe 600mm dia Metre 0365 1,630.00
370 Designing and developing detailed structural and working Drawings for open / Pile / well Set 0370 17,250.00
foundation for RCC column / piers for ROB/RUB/Bridges, based on Railway's approved GADs,
duly designing the members and submission of check plot duly getting proof checked by
Railway approved institutes.
371 Designing and developing detailed structural and working Drawings for RCC bed block for Set 0371 5,175.00
ROB/RUB/Bridges, based on Railway's approved GADs, duly designing the members and
submission of check plot duly getting proof checked by Railway approved institutes.


Code
372 Designing and developing detailed structural and working Drawings for foundation and sub Set 0372 17,250.00
structure for RCC retaining wall, abutment and approach slab for ROB/RUB/Bridges, based on
Railway's approved GADs, duly designing the members and submission of check plot duly
getting proof checked by Railway approved institutes.
373 Exploratory drilling of boreholes of 150mm dia. in all type of soils except hard rock / large Metre 0373 796.00
boulders (boulder core more than 30cm), for collecting the undisturbed core sample including
refilling, reinstating surface and disposing off surplus material including use of mechanical rigs
with power operated winches as well as percussion/chieselling tool for advancing through
occasional seams of hard strata, where necessary with contractor's labour, tools, plants,
machinery, equipment, consumables etc., with all lead and lift complete as per specifications
and as directed by the Engineer-in-charge in Dry area 0-10m
and as directed by the Engineer-in-charge in Dry area 10m-20m
377 Exploratory drilling of boreholes of 150mm dia. in all type of soils except hard rock / large Metre 0377 1,100.00
380 Extra for 150mm dia. bore in hard Rock/large Boulder at all levels Metre 0380 1,489.00
381 Drilling of NX size borehole (75mm dia.) in all types of hard rock (fresh rock) and collection of Metre 0381 2,284.00
rock core samples from boreholes and preserving in boxes 0m-10m


Code
388 Conducting in-situ full size Plate Load Test (PLT) at selected location as per IS:10042 Each 0388 15,000.00
including making loading arrangements & casting of RCC/cast in-situ concrete footing as per
codal provisions including excavation and refilling of trial pit : Plate size- 30cm x 30cm
391 Conducting in situ Vane shear test for soil as per IS:4434 Each 0391 2,200.00
392 Conducting SCPT for soil as per IS:4968 Each 0392 35,000.00
393 Conducting DCPT for soil as per IS:4968 Each 0393 29,000.00
394 Conducting determination of California Bearing Ratio (CBR) as per IS:2720 Each 0394 1,000.00
395 Taking out 100mm dia. & 450mm long undisturbed samples of soil from bore holes, including Each 0395 103.00
provision of air tight containers for packing and, labelling incl. transporting the samples to
laboratory. Piston sampler shall be used for extracting undisturbed samples where necessary.
Samples shall be collected as per IS:2720.
396 Taking out 100mm dia. & 450mm long disturbed samples of soil from bore holes, including Each 0396 110.00
provision of air tight containers for packing, labelling and transporting the samples to
laboratory. Samples shall be collected as per IS:2720.
397 Conducting standard penetration test as per IS:2131 at approximate1.5m intervals in bore Each 0397 600.00
holes, as directed by the Engineer in charge
398 Collection of water samples at required intervals Each 0398 170.00
399 Moisture Contents/Dry Density Each 0399 200.00
400 Atterberg Limit Each 0400 400.00
401 Specific Gravity Each 0401 400.00
402 Grain size analysis including Hydrometer analysis Each 0402 550.00
403 Direct Shear Test Each 0403 1,500.00
404 Natural Density Test Each 0404 450.00
405 Consolidation Test Each 0405 5,000.00
406 Unconfined Compression Test Each 0406 1,500.00
407 Tri-axial Test Each 0407 1,500.00
408 Density Test Each 0408 200.00
409 Water Absorption & Porosity Each 0409 200.00
410 Hardness Test Each 0410 100.00
411 Unconfined Compression Test for rock Each 0411 1,500.00
412 Point Load Test Each 0412 800.00
413 Modulus of Elasticity Each 0413 4,000.00
414 Abrasion Testing Each 0414 450.00
415 Conducting chemical analysis of ground water samples to determine suitability for concreting Each 0415 1,000.00
and aggressiveness in relation to attack on concrete / reinforcement including determination
of pH value
416 Conducting chemical analysis of soil samples to determine aggressiveness in relation to Each 0416 1,000.00
attack on concrete / reinforcement including determination of pH value


Code
417 Supply of Alumino Thermit Welding Portions, 3 piece prefabricated mould (ZIRCON Each 0417 1,610.00
WASHED) manully pressed, Single shot cricible fitted with auto tapping thimble as per RDSO
Specification No IRST/19-2020 and as amended for 60 Kg/90UTS-25mm gap with
accessories as per Annexure -I of IRUSSOR - 2021.
Specification No IRST/19-2020 and as amended for 52 Kg/90UTS-25mm gap with
accessories as per Annexure -I of IRUSSOR - 2021.
Specification No IRST/19-2020 and as amended for 60 Kg/60EI-R260 grade Rail-25mm gap
with accessories as per Annexure -I of IRUSSOR - 2021.
420 Luting Sand for AT welding Kg 0420 10.00
421 Rail file 15" long for filing AT weld Each 0421 450.00
422 CP-3032 Powder for reconditioning of scabs, wheel burns of rails and cupped AT welded joints Kg 0422 1,550.00
423 TERRA C I-94 - Electrodes of make L & T, AdvaniOerlicon, Diffusion, SHARP - 650, or Each 0423 175.00
equivalent for reconditioning of MCI insert of points & crossings sleeper
424 H3 C Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0424 78.13
425 H3 B Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0425 76.50
426 H3 A Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0426 38.75
427 H3 Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0427 20.00
428 1.6mm dia core flux wire of cast manganese steel Kg 0428 916.00
429 10 mm thick Grooved Rubber Pads as per drg. No. RDSO/T-5199 & RDSO's Spec. no. IRS-T- Each 0429 132.00
47-2006 (Prov.)-1989
430 Galvanised steel fittings for non insulated galvanized channel sleepers (52/60 kg rail) as per set 0430 1,534.00
RDSO drawing no. RDSO/T-5197 to 5200
431 Galvanised steel fittings for insulated galvanized channel sleepers (52/60 kg rail) as per RDSO set 0431 2,000.00
drawing no. RDSO/T-5155 to 5164
432 Supply of 25/30 mm thick Elastomeric Pad as per RDSO drawing No. B/1636/I/R2 Each 0432 152.00
433 Supply of 2 nos. Elastomeric Pad 25mm/30mm and 4 nos. Grooved Rubber Pad as per RDSO Set 0433 1,650.00
drawing No. B/1636/5/Alt 2
434 Galvanised MS liner and Outer Clip for steel channel sleeper (RDSO Drg. No. T-6150 & T- Set 0434 434.00
6151)
435 Single Coil spring washers T-10773 Each 0435 4.35
436 Dip Galvanisation @ 705gm / sqm ( 100 Microns thick ) MT 0436 17,000.00
437 Hook Bolts 28mm dia & 320mm long as per RDSO's drg. No. BA-1636/I/R2 Each 0437 35.00
438 Zero toe load galvanised fixtures for H Beam sleepers of 52/60kg Rails as per RDSO Set 0438 3,000.00
approved drawing
439 Lifting Barrier assembly for 6m long Lifting Barrier, having fragmented boom, boom light boxes set 0439 96,858.59
with suitable gate lamps, bell, Boom supports (stay wires) with adjusters, counter weight,
pedestal and lock posts with foundation of ‘A’ type as required, turn union wheel with
brackets, balance and auxiliary weights clamps etc to approved standard drawings to nos SA
7973 to 7980 with all fittings and fastenings complete (excluding fringes)
440 Lifting Barrier assembly for 8m long Lifting Barrier, having fragmented boom, boom light boxes set 0440 129,144.47
with suitable gate lamps, bell, Boom supports (stay wires) with adjusters, counter weight,
pedestal and lock posts with foundation of ‘A’ type as required, turn union wheel with
441 Lifting Barrier assembly for 10m long Lifting Barrier, having fragmented boom, boom light set 0441 161,431.29
boxes with suitable gate lamps, bell, Boom supports (stay wires) with adjusters, counter
weight, pedestal and lock posts with foundation of ‘A’ type as required, turn union wheel with
442 Winch arrangement for operation of level crossing lifting barriers, as per RDSO’s approved Each 0442 35,289.90
layout having standard covering arrangement, foundation of ‘A’ type as required and pulleys,
pulley guides and stakes, horizontal rope wheel, vertical rope wheel, wire adjusting screws
wire ropes 6x6x19 with all fittings, fixtures and accessories to RDSO’s approved drawings
with all parts including painting of steel work as per specification(excluding excavation and
concrete work)


Code
443 Auto boom locking arrangement (Single lever) for existing lifting barriers, consisting of Each 0443 82,481.50
interlocking ground frame near gate lodge, foundation of ‘A’ type as required and connecting
ground frame to lock posts of gate booms with stipulated rodding on guide rollers, supported
on trestles as per RDSO’s drawings complete (Excluding excavation, concrete work)
444 Auto boom locking arrangement (Double lever) for existing lifting barriers, consisting of Each 0444 85,105.91
interlocking ground frame near gate lodge, foundation of ‘A’ type as required and connecting
ground frame to lock posts of gate booms with stipulated rodding on guide rollers, supported
on trestles as per RDSO’s drawings complete (Excluding excavation, concrete work)
445 Railway's lifting barrier assembly of one side at level crossing Each 0445 80,715.65
446 Railway's lifting barrier assembly and boom supports, gate lamps, of one side at level crossing Each 0446 84,751.43
447 GI wire rope of 6mm dia. 6 ply to suit lifting barrier gates Kg 0447 350.00
448 Boom Supports (stay wires) for lifting barrier (approx. 8mm dia) Each 0448 1,000.00
449 4" dia round ceramic Light Reflector as per specification Each 0449 350.00
450 Pulley with Pulley stakes complete, wire rope 6x6x19 ply with accessories as per Railway’s Each 0450 347.00
approved drawings for operation of lifting barriers
451 Vertical / Horizontal Turnout Wheels and Shafts mounted over the base plate weighing not Each 0451 1,320.00
less than 6 Kg with supporting vertical base made of MS angles 75mm x 75mm x 10mm as
per Railway's approved drawing and specifications
452 Turnout wheel- HORIZONTAL ROPE WHEEL double wire (2 way) including guides Each 0452 2,024.00
453 Galvanized STEEL WIRE ROPE for DW signalling 6 x 19 ply as per IRS No. S.11 amended Kg 0453 250.00
upto date for lifting barrier at level crossing gates
454 Precast CC Paver block -80mm thick M35 grade Sqm 0454 495.00
455 Precast CC Paver block -120mm thick M40 grade Sqm 0455 774.00
456 HDPE Dowels Each 0456 100.00
457 High Speed Hacksaw Blade of size 300mm x 12.5mm x 0.63mm (18TPI) as per as per Nos. 0457 160.00
RDSO's Spec. no. TM/SM/26 (latest Rev.)
458 Hack Saw Blades Each 0458 593.22
459 Abrasive rail cutting disc as per RDSO's Spec. no. TM/SM/2 Each 0459 574.00
460 Driving belt (abrasive rail cutter) Each 0460 600.00
461 Grinding Stone wheel GQ6 of 150mm dia Nos. 0461 490.00
462 Shearing Blade for weld trimming machine Each 0462 150.00
463 Rechargeable Battery for ETLMD as per RDSO's Spec. no. TM/SM/ETLMD/218 Each 0463 1,000.00
464 Drill twist made of high speed of size 16 mm dia of Addison / I.T. make Each 0464 1,631.50
465 Drill twist made of high speed of size 7.2 mm dia of Addison / I.T. make Each 0465 271.00
466 Drill twist made of high speed steel for size 26.5mm dia of Addison / I T make Each 0466 2,852.30
467 Drill twist made of high speed steel for size 18mm dia of Addison / I T make Each 0467 1,866.40
468 Drill twist made of high speed steel for size 28.75 mm dia of Addison / I T make Each 0468 3,242.40
469 Drill twist made of high speed steel for size 31.75 mm dia of Addison / I T make Each 0469 4,335.90
470 Drill Bit (32 mm & 26.5 mm dia) Each 0470 300.00
471 Auger Carpenter Each 0471 90.00
472 Hand lever box full set BG Each 0472 11,000.00
473 Point lock pin full set BG Each 0473 720.00
474 Fosroc conbextra-GP2 grout or similar make in 25 Kg bag Each 0474 494.00
475 Black Oil (used lubricating oil) Litre 0475 15.00
476 High intensity retro-reflective sheet Sqm 0476 1,625.00
477 Retro Reflective tape 50mm wide Metre 0477 71.30
478 Steel wires released from U/S PSC Sleeper Kg 0478 15.00
479 Bamboo 50 mm dia 2.5 metre long (1 Score = 20 nos.) score 0479 1,500.00
480 Hollock Ballies 80mm diameter Metre 0480 85.00
481 Hollock Ballies 150mm diameter Metre 0481 150.00
482 150 mm dia Eucalyptus Ballies Metre 0482 143.75
483 125 mm dia ballies of locally available wood Metre 0483 90.00
484 100 mm dia ballies of locally available wood Metre 0484 65.00


Code
485 Iron spike (different sizes) Kg 0485 60.00
486 Nylon rope 5 mm dia Kg 0486 90.00
487 Weedicide Chemical - Glyphosate Litre 0487 296.90
489 Fluorescent Tube Lights 40 Watt Nos. 0489 45.00
490 Hard Wood Peg of 50mm dia & 60 cm long Each 0490 25.00
491 Liquid solution in 250ml pack, having break loose torque of 400Nm to 540Nm, as per Each 0491 2,500.00
ISO:10123 norms with shear strength of liquid solutions as 25 to 35 N/mm2, viscosity 1500 to
3000 (Centipoise) & specific gravity of 1.1 ± 0.05. for tightening of all types of track nuts &
bolts to prevent loosening during vibrations
492 Poly chloroprene rubber based solvent (toluene free) to prevent working out of rubber pads Kg 0492 2,000.00
493 U pin of 6mm dia mild steel of 0.3m length for stone cladding work Each 0493 14.00
494 Cotton Jute Kg 0494 40.00
495 Empty cement bag polythene 50 Kgs capacity Each 0495 5.00
496 Sand Paper Nos. 0496 5.00
497 Poly propylene tarred rope gabion fabricated from 9mm dia rope 100m x 100m mesh with Cum 0497 1,380.00
partition at every 1m interval
498 Precast Concrete bridge No plaque/ stone Each 0498 287.50
499 Precast Concrete bridge foundation details plaque including engraving complete Each 0499 525.00
500 PVC pipe 25 mm dia confirming to IS standard for Electric Wiring Metre 0500 75.00
501 PVC junction boxes 4 way for Electric Work Each 0501 18.99
502 Tracing paper in roll with specification- weight 95gm/m2 width 914mm and length 45.7m Each 0502 250.00
503 Ammonia Print Sheet of 55 to 60 GSM, 914mm wide and 10m long Each 0503 250.00
504 Hire Charges of Total Station instrument Day 0504 200.00
505 Electricity Charges ( 1 Unit ) KWH 0505 7.50
Fixed rate elements
507 Sundries Lumpsum 9901 1.00
508 Add for Water Charges @ 1% Lumpsum 9902 0.01
509 Add for GST @ 12% (multiplying factor 0.1405) Lumpsum 9903 0.14
510 Add for Contractor’s Overheads and Profit @ 15% Lumpsum 9904 0.15
511 Add for Cess @ 1% Lumpsum 9905 0.01
512 Add for working under traffic block @ 5% Lumpsum 9991 0.05
Draft IR Unified Standard Analysis of Rates - 2021 Chapter - 1: Earthwork
CHAPTER - 1 : Earth Work

Item no. Description Unit Rate Rate Quantity Amount
Code (Rs.) (Rs.)
011000 Earthwork in New Lines, Doubling Projects Etc. - Embankments
011010 Preparation of foundation for Embankment by clearing, grubbing, stripping top soil
(average 15 cm), ploughing and pulverizing 15 cm of top of soil with tractor trolley,
mixing water to achieve OMC with water sprinkler or left for natural drying, as
required, and compaction with vibratory roller of suitable capacity to achieve 98%
MDD for laying first layer of soil for embankment construction.
Considering bank height of 5m, formation width 8m additional clearance of 0.5m on

either side.
The total width for clearing = 8m + 2x0.5m +2x2x5m +2x0.5m = 30m
Total area in 1 km = 30,000 Sqm Cost for 30,000 Sqm
Machinery:
Hire charges of dozer 215 HP capacity Hour 0057 1500.00 40.00 60,000.00
Hire charges of tractor with Ripper arrangement Day 0082 1200.00 2.00 2,400.00
Hire charges of Water tanker 5 to 6 KL capacity Hour 0051 150.00 24.00 3,600.00
Hire Charges of Vibratory roller 8 to 10 tonne Hour 0052 600.00 56.00 33,600.00
Labour:
Bhisti (Semi skilled) Day 0023 505.00 3.00 1,515.00
Coolie (Un skilled) Day 0026 431.00 50.00 21,550.00
122,665.00
Add for Water Charges @ 1% Lumpsum 9902 0.01 1,226.65
123,891.65
Add for GST @ 12% (multiplying factor 0.1405) Lumpsum 9903 0.14 17,406.78
141,298.43
Add for Contractor’s Overheads and Profit @ 15% Lumpsum 9904 0.15 21,194.76
162,493.19
Add for Cess @ 1% Lumpsum 9905 0.01 1,624.93
Cost for 30,000 Sqm 164,118.12
Cost of 100 Sqm 100 Sqm 547.06
011020 Benching of existing embankment manually in steps of 30 cm height for

doubling/tripling works in running line to provide proper amalgamation between the
old and new embankments as per RDSO latest Specifications and guidelines
RDSO/2020//GE: IRS-0004 to the entire satisfaction of Engineer in-charge. The item
includes uprooting and disposing of all the vegetation, all lift, descends, ascends and
additional earthwork required for filling due to removal of earth in benching in existing
bank.
Note:
(1) The benching Work shall be done for a maximum height of 0.90 m at any time
based on the the progress of earthwork starting from toe of the embankment.
(2) Benching work shall be certified and recorded before starting the earth work.
(3) Unit for payment shall be km per metre height of the Bank. Height here means
representative average height of the bank in the specified km taken from cross
sectional measurements for earthwork.
(4) Since the rate includes earthwork in steps, payment under this item shall be made
after completion of earthwork to that level.
(5) Cut soil from bank shall not be used in embankment construction and disposed off
away from bank as per the direction of Engineer-in-charge.
Detail of cost for 1 Km of 3 metres height of the embankment

Assuming 3m Height of Bank,
Number of Steps of Benching = 10
Volume of 10 Steps of Benching /1 Km length = 10 x 1000 x 0.5 x 0.30 x 0.60 =900
Cum
@3 Cum/ 1 persons
Rate of the item = Average rate of items of Earthwork of item Numbers 012011,
012012, 012013
Cost of Earthwork for Benching = Average rate of items of Earthwork for SQ1, SQ2,
SQ3 classifications of Soil
Rate of SQ1 Cum 011031 174.14
Rate of SQ2 Cum 011032 259.16
Rate of SQ3 Cum 011033 294.64
Average rate of above 3 items 242.65 900.00 218,382.33 A
Labour:
Labour Unskilled Day 0020 431.00 300.00 129,300.00
Misc:
T&P Lumpsum 9901 1.00 100.00 100.00
Total excluding A 129,400.00
130,694.00

Code (Rs.) (Rs.)
149,056.51
171,414.98
Total excluding A 173,129.13
Cost for 1 Km per 3m 391,511.46
Rate per Km per metre Km 130,503.82
011030 Earthwork in filling in embankment, guide bunds, around buried type abutments,
bridge gaps, trolley refuges, platforms etc. with contractor's own earth conforming to
Soil Quality Class SQ1/SQ2/SQ3, after preparation of foundations as applicable,
benching in existing banks wherever required, spreading in layers with motor grader,
bringing the moisture content to OMC, mechanical compaction to specified density
and dressing of bank to final profile as per RDSO Specifications: RDSO/2020/GE:
IRS-0004 with latest correction slips.
Note:
1) Foundation preparation, Benching including additional earthwork on account of
this, wherever required, shall be paid extra under relevant schedule item for
benching.
2) Payment for Earthwork under this item shall be made based on the cross section
measurements calculated (i) with original ground profile of existing bank based on
initial ground levels before doing benching and (ii) final profile of the bank worked out
with final levels as per prevailing guidelines.
011031 Using Soil Class SQ1

Detail of Cost for 100 cum of finished work
Considering average 3 m height of embankment and 7.85 m formation width, extra
earthwork for new line on account of 50 cm additional width on either side (for
compaction), extra soil required is 6.08%.
Actual quantity of soil required for 100 cum of finished work = 100 +6.08 cum =
106.08 cum
Material:
Soil Quality Class SQ1 suitable for sub grade of embankment as per RDSO Cum 0168 75.00 106.08 7,956.00
Specifications RDSO/2020/GE: IRS-0004
Hire and running charges of Tipper 12 Cum Capacity Day 0048 7000.00 0.15 1,050.00
Hire charges of Hydraulic Excavator (0.9 Cum Bucket Capacity) Day 0044 6400.00 0.17 1,088.00
Hire charges of Motor grader (3.35 metre blade) Hour 0050 2450.00 0.25 612.50
Labour:
Beldar (Un skilled) Day 0025 431.00 2.20 948.20
Coolie (Un skilled) Day 0026 431.00 0.20 86.20
Hire Charges of Vibratory roller 8 to 10 tonne Hour 0052 600.00 1.50 900.00
Hire charges of Water tanker 5 to 6 KL capacity Hour 0051 150.00 1.50 225.00
Sundries Lumpsum 9901 1.00 150.00 150.00
13,015.90
Add for Water Charges @ 1% Lumpsum 9902 0.01 130.16
13,146.06
14,993.08
17,242.04
Add for Cess @ 1% Lumpsum 9905 0.01 172.42
Cost for 100 cum 17,414.46
Rate per Cum Cum 174.14

Detail of Cost for 100 cum
Material:
Labour:
19,369.90
Total 19,563.60

Code (Rs.) (Rs.)
Total 22,312.28
Total 25,659.13
Cost of 100 cum 25,915.72

Material:
Labour:
22,021.90
Total 22,242.12
Total 25,367.14
Total 29,172.21
Cost of 100 cum 29,463.93
012000 Earthwork in New Lines, Doubling Projects Etc. - Cuttings

012010 Earthwork in cutting in formation, trolley refuges, side drains, level crossing
approaches, platforms, catch water drains, diversion of nallah & finishing to required
dimension and slopes to obtain a neat appearance to standard profile inclusive of all
labour, materials, plant & machinery, leading all cut spoils either to make spoil dumps
or for filling in embankment with leads within 2 km on either side of edge of the
cutting(s) including all lifts, ascent, descent, loading, unloading, bailing & pumping
out water, if required, clearance of site and all other works incidental thereto for
completing the work as per RDSO Specification No. RDSO/2020/GE: IRS-0004 with
latest updated correction slips and to the satisfaction of the Engineer-in-Charge.
Note:
(i) All usable earth arising from cut spoils shall be led into bank formation and
Unusable spoils shall be dumped / stacked away from toe of embankment.
(ii) All hard rock /and boulders not fit for filling will be stacked by the contractor and
will be property of the Railways.
(iii)Cut trees shall be property of Railways and to be deposited in the railway godown
unless specified otherwise in the Conditions of Contract.
012011 In all conditions and classifications of soil except rock

Bucket Capacity = 0.90 Cum
Cycle time = 35 Sec
Efficiency = 70%
Capacity = 0.9 x 60 x 60 x 0.70)/35 = 64.80 Cum/hour
Average output per day = 8 x 64.8 = 518 Cum
Machinery:
Labour:
Helper (Semi-skilled) Day 0021 505.00 4.00 2,020.00
Beldar (Un skilled) Day 0025 431.00 8.00 3,448.00
39,868.00
40,266.68
45,924.15
52,812.77

Code (Rs.) (Rs.)
Total for 518 Cum 53,340.90
012012 Soft rock not requiring blasting

Cycle time = 35 Sec x 4 = 140 Sec (Due to rock there will be more cycle time)
Efficiency =70%
Average output per day = 8 x 16.40 = 131.2 Cum
Machinery:
Labour:
Rock Excavator (Semi skilled) Day 0014 505.00 3.00 1,515.00
Rock Breaker (Semi skilled) Day 0015 505.00 3.00 1,515.00
Rock Hole Driller (Semi skilled) Day 0016 505.00 1.00 505.00
22,672.00
22,898.72
26,115.99
30,033.39
Cost for 150 Cum 30,333.72
012013 In hard rock requiring blasting

Cycle time = 35 Sec x 4 = 140 Sec (Due to rock there will be more cycle time)
Efficiency = 80%
Average output per day = 8 x 18.75 = 300 Cum
Excavator required = 150/300 = 0.5 days
Tipper required (considering twice the number due to less volume of rock to be
accommodated and more time of loading also) = 2 nos..
Machinery:
Labour:
Rock Hole Driller (Semi skilled) Day 0016 505.00 7.00 3,535.00
Beldar (Semi Skilled) Day 0024 505.00 7.00 3,535.00
Material
Blasting Powder Kg 0171 50.00 52.00 2,600.00
Blasting Fuse (Fuse Wire) Each 0172 20.00 75.00 1,500.00
37,965.00
38,344.65
43,732.07
50,291.88
Cost for 150 Cum 50,794.80
012014 In hard rock with hammer / chisel / pavement breaker etc. where blasting is not
permitted due to special circumstances and if specifically ordered in writing including
drilling and all incidental works thereto.

Code (Rs.) (Rs.)
Machinery:
Hire charges of Hydraulic Excavator (0.9 Cum Bucket Capacity) Day 0044 6400.00 0.10 640.00
Hire and running charges of Tipper 12 Cum Capacity Day 0048 7000.00 0.10 700.00
Labour:
Stone Chiseller (Semi skilled) Day 0017 505.00 1.00 505.00
Blacksmith - 2nd Class (Semi-skilled) Day 0009 505.00 0.18 88.38
5,943.13
6,002.56
Add for GST @ 12% (multiplying factor 0.1405) Lumpsum 9903 0.14 843.36
6,845.92
7,872.80
Cost for 10 cum 7,951.53
012015 Extra for leading of Cut spoil every one km beyond original lead of 2 km over item no.
011010
Cost for 12 cum for additional leading of 1 km
56.00
56.56
64.51
Add for Contractor’s Overheads and Profit @ 15% Lumpsum 9904 0.15 9.68
74.18
Cost for 12 cum 74.92
012020 Foundation preparation in cutting - ploughing and pulverizing 15 cm of top of soil with
tractor trolley, mixing water to achieve OMC with water sprinkler or allowing for
natural drying, as required, and compaction with vibratory roller of suitable capacity to
achieve 98% MDD for laying blanketing layer
Considering cost for 30,000 Sqm

Machinery:
Hire charges of Water tanker 5 to 6 KL capacity Hour 0051 150.00 24.00 3,600.00
Labour:
Bhisti (Semi skilled) Day 0023 505.00 3.00 1,515.00
44,994.00
45,443.94
51,828.81
59,603.14
Cost for 30,000 Sqm 60,199.17
Cost of 100 Sqm 100 Sqm 200.66
012030 Mechanical manufacturing of blanketing material by using only hard and durable
stone crushed in mechanical crusher to different gradations, wet mixing of the same
in designed proportion in Pug mill or wet mix plant to have uniform gradation including
all incidental transportation, laying over finished formation in uniform layer(s) with
motor grader, compaction with suitable vibratory roller to specified density and
finishing to correct profile, complete as per RDSO Specification No. RDSO/2020/GE:
IRS-0004 with latest correction slips.
Note: This item shall be used only when entire constituent of blanketing material is
mechanically manufactured.

Code (Rs.) (Rs.)
Wastage due to additional 50 cm width is about 9.76% . For 225 cum (450 MT) of
finished work, total volume of blanketing material required = 225 x1.0976 = 246.96
cum (493.92 MT)
Material:
Detail of cost for 225 cum (450 MT) finished quantity at site after compaction
Stone Aggregate (Single size) : 20 mm nominal size Cum 0207 825.00 45.69 37,696.80
Crusher Screening(Quarry Dust) Conforming to Grading Zone - I to Zone- II Cum 0211 600.00 114.22 68,529.75
Machinery:
Hire Charges of Wet Mix Plant 60 TPH Capacity Hour 0055 950.00 8.25 7,837.50
Hire Charges of Generator 100 KVA/125 KVA Day 0076 2500.00 1.03 2,575.00
Hire and running charges of front end loader (1.0 Cum bucket capacity) Day 0047 6000.00 0.75 4,500.00
Transportation of material within a distance of 5 kms on either side of the Wet Mix
plant requires 2.8 tippers.
Add 10% of cost of carriage to cover cost of loading and unloading 0.10 1,960.00
Machinery for spreading in layers, profiling and compacting at work site
Hire charges of Motor grader (3.35 metre blade) Hour 0050 2450.00 1.50 3,675.00
Labour:
Mate (Semi skilled) Day 0003 505.00 0.40 202.00
Total 279,238.79
282,031.18
321,656.56
369,905.05
Cost for 225 cum 373,604.10
Rate per Cum Cum 1,660.46
012040 Manufacturing of blanketing material by wet mixing of naturally available suitable soil
including additional blending with naturally available or manufactured material as
required to achieve specified gradation, in designed proportion in Pug mill or wet mix
plant to have uniform gradation including all incidental transportation, laying over
finished formation in uniform layer(s) with motor grader, compaction with suitable
vibratory roller to specified density and finishing to correct profile, complete as per
RDSO Specification No. RDSO/2020/GE: IRS-0004 with latest correction slips.
Wastage due to additional 50 cm width is about 9.76% . For 225 cum finished work,
total volume of blanketing material required = 246.96 cum.
Material:
Considering 80% of the Blanketing Quantity as naturally available material and 20%
qnty for Blending material.
Natural soil = 0.8*246.96 = 197.57 cum
Blending material = 0.20x246.96 = 49.39 cum
Since this is naturally available, the cost shall be the same cost of Soil as SQ3.
However, in all probability it may be available at a reasonable distance away from
worksite in most of the cases. Distance of availability of material is considered as
additional 30 km for analysis purpose.
Considering availability of natural material meeting the specification may not be in
close vicinity, a distance of 30 km is considered for calculation of additional cost for
transportation.
Cost of 30 km of transportation for 197.56 cum as per working sheet
Cost of transportation cum 159.89 197.57 31,588.65

Considering 20% of Blending Material, Qnty of Blending material =
Machinery:

Code (Rs.) (Rs.)
Machinery for spreading in layers, profiling and compacting at work site
Hire charges of Motor grader (3.35 metre blade) Hour 0050 2450.00 1.50 3,675.00
Labour:
139,940.65
141,340.05
161,198.33
185,378.08
Cost for 225 cum 187,231.86
012050 Mechanical manufacturing and supply of blanketing material by using only hard and
durable stone crushed in mechanical crusher to different gradations, wet mixing of the
same in designed proportion in Pug mill or wet mix plant to have uniform gradation as
per RDSO Specification No. RDSO/2020/GE: IRS-0004 with latest correction slips
including transportation to nominated place and stacking.
Note:
1.This item shall be used only when entire constituent of blanketing material is
mechanically manufactured.
2. Measurement shall be done as per Stack measurement.
For 246.96 cum (493.92 MT) of compacted blanketing, the volume in loose state
shall be 246.96 x 1.20 = 296.352 cum.
Material:
Detail of cost for 296.352 cum in stacks
Machinery:
Labour:
Total 270,037.79
272,738.17
311,057.88
357,716.57
Cost for 296.352 cum 361,293.73
012060 Manufacturing of blanketing material by wet mixing of different types of naturally

available suitable soil including additional blending with naturally available or
manufactured material as required to achieve specified gradation, in designed
proportion in Pug mill or wet mix plant to have uniform gradation as per RDSO
Specification No. RDSO/2020/GE: IRS-0004 with latest correction slips including all
incidental transportation and stacking at site in Stacks.
Note: Measurement shall be done in as per Stack measurement.
For 246.96 cum (493.92 MT) of compacted blanketing, the volume in loose state
shall be 246.96 x 1.20 = 296.352 cum.
Material:

Code (Rs.) (Rs.)
Considering 80% of the Blanketing Quantity as naturally available and 20% qnty for
Blending
Natural soil = 0.8*246.96 = 197.57 cum
Blending material = 0.20x246.96 = 49.39 cum
Since this is naturally available, the cost shall be the same cost of Soil as SQ3.
However, in all probability it may be available at a reasonable distance away from
worksite in most of the cases. Distance of availability of material is considered as
additional 30 km for analysis purpose.
Soil Quality Class SQ3 suitable for sub grade of embankment as per RDSO
Cum 0170 150.00 197.57 29,635.50
Considering availability of natural material meeting the specification may not be in
close vicinity, a distance of 30 km is considered for calculation of additional cost for
transportation.
Cost of 30 km of transportation for 197.56 cum as per working sheet
Cost of transportation Cum 159.89 197.57 31,588.65

Considering 20% of Blending Material, Qnty of Blending material =
Machinery:
Labour:
130,739.65
132,047.04
150,599.65
173,189.60
Cost for 296.352 cum 174,921.50
013000 Miscellaneous:
013010 Felling trees of girth (measured at a height of 1m above ground level) including lead
and stacking of material within 100m.
Note : 1. When stumps are grubbed up in addition, the rates shall be doubled for
trees cut and grubbed 2. Payment for grubbing shall only be made where specially
ordered. 3. Grubbing shall be ordered only where it is essential to remove the
stumps, including the roots, as per specification. 4. Grubbing shall include removal of
roots of trees and saplings to a depth of 60cm below ground level or 30 cm below
formation level or 15 cm below sub grade level, whichever is lower.
013011 Girth over 30 cm and upto 60 cm

Details of cost for 1 tree
Labour:
220.50
222.71
254.00
292.09
Rate per Tree Each 295.02
013012 Girth over 60 cm and upto 1.5m

Labour:

Code (Rs.) (Rs.)
608.40
614.48
700.82
805.94
Rate per Tree Each 814.00
013013 Girth over 1.5m upto 3 m

Labour:
1,211.80
1,223.92
1,395.88
1,605.26
Rate per Tree Each 1,621.31
013014 Girth over 3 m

Labour:
2,030.70
2,051.01
2,339.17
2,690.05
Rate per Tree Each 2,716.95
013020 Turfing / planting, including all lead & lift and watering as required until properly
rooted with.
Note: Initially payment of only 40% will be made. Balance 60% will be paid only after
3 months of maintenance period, if the turfing is properly rooted.
013021 Turfing with sods, 10cm thick and 20cm square closely laid.
Details of cost for 100 Sqm.
Material:
Grass sods Sqm 0176 46.00 70.00 3,220.00
{Considering coverage of 70% area of turfing with sods}
Labour:
Bhisti (Semi skilled) Day 0023 505.00 0.50 252.50
4,354.50
4,398.05
5,015.97
5,768.37
Rate per 100 Sqm 100 Sqm 5,826.05
013022 Turfing with planted doob grass.

Material:
Doob grass Sqm 0174 29.00 70.00 2,030.00
{Considering coverage of 70% area of turfing}
Labour:

Code (Rs.) (Rs.)
4,195.00
4,236.95
4,832.24
5,557.08
Rate per 100 Sqm 100 Sqm 5,612.65
013023 Planting Sarkanda / sarpat or any other suitable species approved by the engineer
Details of cost for 100sqm
Material:
Sarkanda/ Sarpat Sqm 0175 45.00 70.00 3,150.00
{Considering coverage of 70% area of turfing
Labour:
4,894.00
4,942.94
5,637.42
6,483.04
Rate per 100 Sqm 100 Sqm 6,547.87
013030 Cleaning out silt from bed of reservoir/canals including 50m lead and lift upto 1.5m.
Taking output 10 cum
Labour:
1,303.00
1,316.03
1,500.93
1,726.07
Cost for 10 Cum 1,743.33
013040 Providing and removing barricading with the help of portable fencing along running
track where work is to be done in close vicinity of track. Fencing shall consist of self
supporting steel angles of size 50mm x 50mm x 6mm, 1.5m long provided with hooks
etc. and embedded in CC 1:2:4 block of size 0.23m x 0.23m x 0.23m placed at c/c
distance of 2m along track. 12mm dia rods in three horizontal layers shall be tack
welded with angle posts.
Note : Released material will be property of the contractor after completion of work.
Cost of cement to be paid separately.
013041 With provision of one 50mm wide retro-reflective tape in horizontal direction, duly
secured/tight with vertical posts.
Details of cost for 30m
Material:
Steel angle supports 50mm x 50mm x 6mm (steel angles to be used 8 times). Quintal 0224 4950.00 0.14 688.05
Therefore, quantity taken = 1.1 / 8 = 0.14 qtl.)
Weight of Angle of size 50mm x 50mm x 6mm is 4.5 kg/m
15 no. x 1.5m = 22.5m @ 4.5kg/m = 101.25 kg (Add 5% extra for wastage) = 111.375
kg say 1.1 qtl.
MS round bar for reinforcement- average rate for various dia Quintal 0220 3600.00 0.11 400.50
M.S. bars 12mm dia = 30m x 3no. x 0.89 = 0.80 quintal (Steel to be used 8 times).
Less salvage value after full use of material @ 25% on (A + B) -272.14

Code (Rs.) (Rs.)
Retro Reflective tape 50mm wide Metre 0477 71.30 31.50 2,245.95
Stone Aggregate (Single size) : 20 mm nominal size Cum 0207 825.00 0.16 135.30
Coarse Sand (Zone III) Cum 0202 1200.00 0.08 98.40
Labour:
Mason 2nd class (Semi-skilled) Day 0005 505.00 1.00 505.00
4,302.56
4,345.59
4,956.14
5,699.56
Cost of 30 m 5,756.56
Rate per metre Metre 191.89
013042 With provision of painting verticals & horizontals with red luminous paints / strips of
30cm each with a gap of 30 cm.
Taking out put 30m
Material:
Structural steel such as T, Angles, Channels and R S Joists conforming to Grade Quintal 0224 4950.00 0.14 688.05
Weight of Angle of size 50mm x 50mm x 6mm is 4.5 kg/m
15no's x 1.5m = 22.5m @ 4.5kg/m = 101.25 kg (Add 5% extra for wastage) =
111.375 kg say 1.1 qtl.
Considering angles to be used 8 times, quantity taken for one time use = 1.1 / 8 =
0.14 qtl.)
M.S. bars 12mm dia = 30m x 3no. x 0.89 = 0.80 quintal (Steel to be used 8 times).
Less salvage value after full use of material @ 25% on (A + B) -271.91
Luminous Paint as per RDSO's Spec. no. M&C/PCN/120-2011 Litre 0299 300.00 0.40 120.00
Surface area of angle 50mm + 50mm + 6mm + 6mm = 112mm, for 22.5 metre long
angle, Area = 22.5m x .112m = 2.52 Sqm, Surface area of 12mm dia rods for 90m
long = 3.42 Sqm, i.e. Total coverage Area = 2.52sqm + 3.42sqm = 5.94 Sqm, Paint
required @ 15sqm/litre = 5.94 / 15 = 0.396 litre
Cement Concrete 1:2:4=0.182cum

Labour:
Painter (Skilled) Day 0012 609.00 0.20 121.80
2,297.74
2,320.71
2,646.78
3,043.79
Cost of 30 m 3,074.23
013050 Provision of barricading with contractor's bamboos / balli vertical post of 100mm dia.
planted at every 2m interval, projecting at least 1.5m above ground level and driven
firmly (minimum 0.5m) inside ground and including painting verticals & horizontals
with red luminous paints / strips at alternative bay on barricade. Barricades shall be
maintained through out the execution of the work and shall be removed in workman
like manner on completion of the work only after instruction of Engineer in-Charge.
Note:
(1) 60% payment shall be made on provision of barricading at work-site and balance
40% payment after removal of barricades.
(2) The released ballies shall be the property of the Contractor.

Code (Rs.) (Rs.)
013051 With 3 horizontal bamboo / balli members of minimum 50mm dia. spaced equally
Details of cost for 100 RM

Material:
Considering use of ballies 3 times and 20% overlapping, the quantity to be taken for 1
time use for 100 RM
(i) Quantity of 50 mm ballies in 100 RM = 3 x 100 x 1.2 m 360m = 360/2.5 = 144 nos.
= 144/20 = 7.2 scores. Quantity for one time use = 7.2/3 = 2.42 Scores Say 2.50
Scores
(ii) Quantity of 100 mm ballies in 100 RM = 100/2 = 50 nos. = 50 x 2 = 100 m.
Quantity for one time use = 100/3 = 33.33 Say 34 m
Bamboo 50 mm dia 2.5 metre long (1 Score = 20 nos.) score 0479 1500.00 2.50 3,750.00
100 mm dia ballies of locally available wood Metre 0484 65.00 34.00 2,210.00
Iron spike (different sizes) Kg 0485 60.00 2.00 120.00
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
Carpenter (Skilled) Day 0006 609.00 1.00 609.00
Helper (Semi-skilled) Day 0021 505.00 1.00 505.00
Misc :
T&P Lumpsum 9901 1.00 16.00 16.00
9,986.25
10,086.11
11,503.21
13,228.69
Cost for 100 RM 13,360.98
Rate per RM RM 133.61
013052 Joining with strong nylon rope in one cross and one horizontal pattern of minimum
5mm dia.
Material:
Iron spike (different sizes) Kg 0485 60.00 2.00 120.00
Nylon rope 5 mm dia Kg 0486 90.00 12.00 1,080.00
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
Misc:
T&P Lumpsum 9901 1.00 15.00 15.00
5,858.25
5,916.83
6,748.15
7,760.37
Cost for 100 RM 7,837.97
013060 Supplying, driving and erecting in all types of soils, hard wood pile 5m to 7m long
without joint, 125mm average dia. for protection of bank slope including two coats of
coal tar paint complete, as directed
Note: Payment will be made as per actual driven length of pile.
Details of cost for 100 m pile

Material:
Coal tar Emulsion Litre 0317 50.00 5.00 250.00
Hire charges of Derrick Monkey Rope Day 0061 750.00 1.00 750.00
Labour:
Mistry (Semi skilled) Day 0027 505.00 1.00 505.00

Code (Rs.) (Rs.)
13,641.00
13,777.41
15,713.14
18,070.11
18,250.81
Cost for 100 metre pile 18,250.81
013070 Driving rails 90R/52 Kg section below average ground level within the slope/toe of
embankment including making of nose with contractor’s own arrangement complete
in all respect
Note: Payment will be made as per actual driven length of rail which will be supplied
free by Railways at site of work.
Details of cost for 100 metre rail driving

Material:
Hire charges of Derrick Monkey Rope Day 0061 750.00 1.00 750.00
Labour:
7,008.00
7,078.08
8,072.55
9,283.43
Cost for 100 metre rail driving 9,376.27
013080 Shoring with 'Z' section MS sheet piles side by side in all kinds of soil mechanically or
manually as per approved drawing with contractor’s own arrangement complete in all
respects and removal of sheet piles after completion of the work as directed by
engineer in-charge
Note: Payment will be made as per actual driven length of pile.
Details of cost for 100 m of Z section Pile having wall area of 100x0.80 = 80.00 Sqm.
Material:
AZ 18-800 Sheet piles 100m @ 80.70 kg/m=8070 kg=80.70 Quintals. Add 10% for
bracing.
Total weight = 80.70 x 1.10 = 88.077quintals
This can be used 12 times with a salvage value of 25% , the weight to be taken for
using once = 0.75 x 88.77/12 = 5.5048 Say 5.505 quintal
Z section sheet piles AZ 18-800 (Arcellor Mittal) or equivalent & bracing Quintal 0249 4500.00 5.51 24,772.50
Hire charges of Vibratory Hammer attachment of Hydraulic Excavator for driving Day 0046 700.00 0.75 525.00
Sheet pile driving
Hire charges of Diesel Truck - 9 tonne Day 0060 3940.00 2.00 7,880.00
( 1 day for transportation of material to work site and 1 day for return)
Extra 20% of Hire Charges of Truck for loading unloading 0.20 1,576.00
Labour:
Mistry (Semi skilled) Day 0027 505.00 2.00 1,010.00
47,559.50
48,035.10
54,784.03
63,001.63
Cost per 80 Sqm 63,631.65
Rate per Sqm Sqm 795.40

Code (Rs.) (Rs.)
013090 Supplying, laying Non-woven Needle Punched and Mechanically or Thermally

bonded type Geotextile for use as Separator/Filtration for Railway formation as per
RDSO Specification No. RDSO/2018/GE:IRS-0004 - Part I made of Polypropylene /
Polyethylene / Polyamide or combination there of having apparent opening size of ≤
85 microns and elongation at failure > 50% in both directions including transportation
labour, lead & lift complete as directed by Engineer in-charge.
013091 On top of subgrade or prepared subgrade before laying blanketing layer with
minimum strengths in Grab test, Trapezoidal Tear test and Puncture test of 700N,
250 N and 1800 N respectively.
Cost for 100 Sqm
Material:
Non-woven Needle Punched and Mechanically or Thermally bonded type Geotextile Sqm 0177 90.00 100.00 9,000.00 P
for use as Separator/Filtration for Railway formation as per RDSO Specification No.
RDSO/2018/GE:IRS-0004 - Part Iwith minimum strengths in Grab test, Trapezoidal
Tear test and Puncture test of 700N, 250 N and 1800 N respectively
Add 10 % of P for wastage and accessories for joining elements, overlap, 0.10 900.00
transportation etc.
Labour:
11,253.60
11,366.14
12,963.08
14,907.54
Cost for 100 Sqm 15,056.62
013092 Below the ballast and above blanket layer with minimum strengths in Grab test,
Trapezoidal Tear test and Puncture test of 1750N, 800 N and 5800 N respectively.
Cost for 100 Sqm

Material:
Non-woven Needle Punched and Mechanically or Thermally bonded type Geotextile Sqm 0178 170.00 100.00 17,000.00 P
for use as Separator/Filtration for Railway formation as per RDSO Specification No.
RDSO/2018/GE:IRS-0004 - Part I with minimum strengths in Grab test, Trapezoidal
Tear test and Puncture test of 1750N, 800 N and 5800 N respectively.
Add 10 % of P for wastage and accessories for joining elements, overlap, 0.10 1,700.00
transportation etc.
Labour:
20,053.60
20,254.14
23,099.84
26,564.82
Cost for 100 Sqm 26,830.47
013093 Supplying & laying of drainage composite for use behind abutments, wing walls,
return walls and Retaining walls Geocomposite drain (Vertical) as per RDSO
Specification No. RDSO/2018/GE:IRS-0006 latest version with all material, labour,
equipment, tools and plants, lead, lift etc. complete in all respects as per the direction
of Engineer-in-Charge.
Cost for 100 Sqm

Material:

Code (Rs.) (Rs.)
Geo-composite drain consisting of Geonet Core sandwiched between Non-Woven Sqm 0179 450.00 100.00 45,000.00 P
geo textile filters on both sides as per RDSO Specification No. RDSO/2018/GE:IRS-
0006
Add 10 % of P for wastage and accessories for joining elements, overlap, 0.10 4,500.00
transportation, perforated pipes etc.
Labour:
50,853.60
51,362.14
58,578.52
67,365.29
Cost for 100 Sqm 68,038.95
Draft IR Unified Standard Analysis of Rates - 2021 Chapter - 2: Bridge Works (Sub-structure)
CHAPTER - 2 : Bridge Works Substructure

Code (Rs.) (Rs.)
021000 Soil Exploration and Testing
021010 Exploratory drilling of boreholes down to required depth, drilling of 150mm dia.
boreholes in all type of soils except hard rock & large boulders (boulder core more
than 30cm) including refilling, reinstating surface and disposing off surplus material
including use of mechanical rigs with power operated winches as well as
percussion/chiselling tool for advancing through occasional seams of hard strata to
be employed, where necessary in Dry area.
021011 0m to 10m
Exploratory drilling of boreholes of 150mm dia. in all type of soils except hard rock / Metre 0373 796.00 1.00 796.00
large boulders (boulder core more than 30cm), for collecting the undisturbed core
sample including refilling, reinstating surface and disposing off surplus material
percussion/chieselling tool for advancing through occasional seams of hard strata,
where necessary with contractor's labour, tools, plants, machinery, equipment,
consumables etc., with all lead and lift complete as per specifications and as directed
by the Engineer-in-charge in Dry area 0-10m
796.00
Total 803.96
916.92
1,054.45
Cost per meter Metre 1,065.00
021012 10m to 20m

by the Engineer-in-charge in Dry area 10m-20m
836.00
Total 844.36
962.99
1,107.44
021013 20m to 30m

880.00
888.80

Code (Rs.) (Rs.)
1,013.68
1,165.73
021014 30m to 40m

955.00
964.55
1,100.07
1,265.08
021015 40m to 50m

Exploratory drilling of boreholes of 150mm dia. in all type of soils except hard rock / Metre 0377 1100.00 1.00 1,100.00
1,100.00
1,111.00
1,267.10
1,457.16
021016 50m to 60m

1,300.00
1,313.00
1,497.48

Code (Rs.) (Rs.)
1,722.10
021017 60 m to 70 m
1,400.00
1,414.00
1,612.67
1,854.57
021020 Exploratory drilling of Boreholes down to required depth, drilling of 150mm diameter
boreholes in all type of soils except hard rock and large boulders (boulder core more
than 30cm), including refilling, reinstating surface and disposing off surplus material
including use of mechanical rigs with power operated winches as well as percussion /
chiselling tool for advancing through occasional seams of hard strata to be employed
where necessary in River bed area including standing/flowing water with all
necessary arrangements except making of platform under water which shall be paid
under relevant item of SOR.
021021 0m to 10m
Rate as per item no 021011 for drilling in dry area Metre 021011 1,065.00
Add extra for doing drilling in water 20% over item no 021011 0.20 213.00
021022 10m to 20m

021023 20m to 30m

021024 30m to 40m

021025 40m to 50m

021026 50m to 60m


Code (Rs.) (Rs.)
021027 60m to 70m

021030 Extra for 150mm dia. bore in hard Rock/large Boulder at all levels
Extra for 150mm dia. bore in hard Rock/large Boulder at all levels Metre 0380 1489.00 1.00 1,489.00
1,489.00
1,503.89
1,715.19
1,972.46
021040 Erection of temporary working platform to drill bore hole through flowing/standing
water through river bed upto water depth of 1.5m, and dismantling after completing
work and removing from the site to clear the water way.
Details of cost for 3m x 3m x 2m high Platform =18 cum

Material:
150 mm dia Eucalyptus Ballies Metre 0482 143.75 104.00 14,950.00
Salvage value to be deducted @ 10% after compensating for the cost of dismantling 0.10 -1,495.00
and removing platform from water body.
Filled sand bags (30 kg weight) Each 0201 9.00 500.00 4,500.00
Labour:
Mistry (Semi skilled) Day 0027 505.00 3.00 1,515.00
Carpenter (Semi skilled) Day 0007 505.00 3.00 1,515.00
30,290.00
30,592.90
34,891.20
40,124.88
Cost per Cum Cum 2,251.45
021050 Drilling of NX size borehole (75mm dia.) in all types of hard rock and collection of
rock core samples from boreholes and preserving in boxes
021051 0m to 10m
Drilling of NX size borehole (75mm dia.) in all types of hard rock (fresh rock) and Metre 0381 2284.00 1.00 2,284.00
collection of rock core samples from boreholes and preserving in boxes 0m-10m
2,284.00
2,306.84
2,630.95
3,025.59

Code (Rs.) (Rs.)
021052 10m to 20m

2,399.00
2,422.99
2,763.42
3,177.93
021053 20m to 30m

2,558.00
2,583.58
2,946.57
3,388.56
021054 30m to 40m

2,741.00
2,768.41
3,157.37
3,630.98
021055 40m to 50m

2,835.00
2,863.35
3,265.65
3,755.50
021056 50m to 60m

3,056.00

Code (Rs.) (Rs.)
3,086.56
3,520.22
4,048.25
021057 60m to 70m

3,300.00
3,333.00
3,801.29
4,371.48
021060 Conducting in-situ full size Plate Load Test (PLT) at selected location as per IS:1888
including making loading arrangements & casting of RCC/cast in-situ concrete
footing as per codal provisions including excavation and refilling of trial pit.
021061 Plate size 30cm x 30cm

Conducting in-situ full size Plate Load Test (PLT) at selected location as per Each 0388 15000.00 1.00 15,000.00
IS:10042 including making loading arrangements & casting of RCC/cast in-situ
concrete footing as per codal provisions including excavation and refilling of trial pit :
Plate size- 30cm x 30cm
15,000.00
15,150.00
17,278.58
19,870.36
Cost of Each Each 20,069.06

18,000.00
18,180.00
20,734.29
23,844.43


Code (Rs.) (Rs.)
21,500.00
21,715.00
24,765.96
28,480.85
021070 Conducting in situ Vane shear test for soil as per IS:4434
Conducting in situ Vane shear test for soil as per IS:4434 Each 0391 2200.00 1.00 2,200.00
2,200.00
2,222.00
2,534.19
2,914.32
021080 Conducting SCPT for soil as per IS:4968

Conducting SCPT for soil as per IS:4968 Each 0392 35000.00 1.00 35,000.00
35,000.00
35,350.00
40,316.68
46,364.18
021090 Conducting DCPT for soil as per IS:4968

Conducting DCPT for soil as per IS:4968 Each 0393 29000.00 1.00 29,000.00
29,000.00
29,290.00
33,405.25
38,416.03
021100 Conducting determination of California Bearing Ratio as per IS:2720

Conducting determination of California Bearing Ratio (CBR) as per IS:2720 Each 0394 1000.00 1.00 1,000.00
1,000.00
1,010.00
1,151.91
1,324.69

Code (Rs.) (Rs.)
021110 Taking out 100mm dia. & 450mm long undisturbed samples of soil from bore holes,
including provision of air tight containers for packing and, labeling incl. transporting
the samples to laboratory. Piston sampler shall be used for extracting undisturbed
samples where necessary. Samples shall be collected as per IS:2720.
Taking out 100mm dia. & 450mm long undisturbed samples of soil from bore holes, Each 0395 103.00 1.00 103.00
including provision of air tight containers for packing and, labelling incl. transporting
the samples to laboratory. Piston sampler shall be used for extracting undisturbed
samples where necessary. Samples shall be collected as per IS:2720.
103.00
104.03
118.65
136.44
Cost of Each Each 137.81
021120 Taking out 100mm dia. & 450mm long disturbed samples of soil from bore holes,
including provision of air tight containers for packing, labeling and transporting the
samples to laboratory. Samples shall be collected as per IS:2720.
Taking out 100mm dia. & 450mm long disturbed samples of soil from bore holes, Each 0396 110.00 1.00 110.00
including provision of air tight containers for packing, labelling and transporting the
samples to laboratory. Samples shall be collected as per IS:2720.
110.00
111.10
126.71
145.72
021130 Conducting standard penetration test as per IS:2131 at approximate1.5m intervals in

bore holes, as directed by the Engineer in charge
Conducting standard penetration test as per IS:2131 at approximate1.5m intervals in Each 0397 600.00 1.00 600.00
bore holes, as directed by the Engineer in charge
600.00
606.00
691.14
794.81
021140 Collection of water samples at required intervals

Collection of water samples at required intervals Each 0398 170.00 1.00 170.00
171.70
195.82

Code (Rs.) (Rs.)
225.20
021150 Conducting laboratory Tests on collected soil samples as per relevant IS code
021151 Moisture Content/Dry Density

Moisture Contents/Dry Density Each 0399 200.00 1.00 200.00
202.00
230.38
264.94
021152 Atterberg Limits

Atterberg Limit Each 0400 400.00 1.00 400.00
404.00
460.76
529.88
021153 Specific Gravity

Specific Gravity Each 0401 400.00 1.00 400.00
400.00
404.00
460.76
529.88
021154 Grain size analysis including Hydrometer analysis

Grain size analysis including Hydrometer analysis Each 0402 550.00 1.00 550.00
550.00
555.50
633.55
728.58
021155 Direct Shear Test

Direct Shear Test Each 0403 1500.00 1.00 1,500.00
1,500.00
1,515.00

Code (Rs.) (Rs.)
1,727.86
1,987.04
021156 Natural Density

Natural Density Test Each 0404 450.00 1.00 450.00
450.00
454.50
518.36
596.11
021157 Consolidation Test

Consolidation Test Each 0405 5000.00 1.00 5,000.00
5,000.00
5,050.00
5,759.53
6,623.45
021158 Unconfined Compression Test

Unconfined Compression Test Each 0406 1500.00 1.00 1,500.00
1,500.00
1,515.00
1,727.86
1,987.04
021159 Tri-axial Test

Tri-axial Test Each 0407 1500.00 1.00 1,500.00
1,500.00
1,515.00
1,727.86
1,987.04
021160 Conducting Laboratory tests on collected ROCK SAMPLES as per relevant IS code
021161 Density Test

Density Test Each 0408 200.00 1.00 200.00
200.00

Code (Rs.) (Rs.)
202.00
230.38
264.94
021162 Water Absorption & Porosity

Water Absorption & Porosity Each 0409 200.00 1.00 200.00
200.00
202.00
230.38
264.94
021163 Hardness
Hardness Test Each 0410 100.00 1.00 100.00
100.00
101.00
115.19
132.47
021164 Unconfined Compression Test

Unconfined Compression Test for rock Each 0411 1500.00 1.00 1,500.00
1,500.00
1,515.00
1,727.86
1,987.04
021165 Point Load Test

Point Load Test Each 0412 800.00 1.00 800.00
800.00
808.00
921.52
1,059.75
021166 Modulus of Elasticity

Modulus of Elasticity Each 0413 4000.00 1.00 4,000.00

Code (Rs.) (Rs.)
4,000.00
4,040.00
4,607.62
5,298.76
021167 Abrasion Testing

Abrasion Testing Each 0414 450.00 1.00 450.00
450.00
454.50
518.36
596.11
021170 Conducting chemical analysis of ground water samples to determine suitability for
concreting and aggressiveness in relation to attack on concrete / reinforcement
including determination of pH value
Conducting chemical analysis of ground water samples to determine suitability for Each 0415 1000.00 1.00 1,000.00
concreting and aggressiveness in relation to attack on concrete / reinforcement
including determination of pH value
1,000.00
1,010.00
1,151.91
1,324.69
021180 Conducting chemical analysis of soil samples to determine aggressiveness in

relation to attack on concrete / reinforcement including determination of pH value
Conducting chemical analysis of soil samples to determine aggressiveness in Each 0416 1000.00 1.00 1,000.00
relation to attack on concrete / reinforcement including determination of pH value
1,000.00
1,010.00
1,151.91
1,324.69
022000 OPEN FOUNDATION AND PILE FOUNDATION


Code (Rs.) (Rs.)
022010 Earthwork in excavation by mechanical means (Hydraulic Excavator)/Manual Means
for foundations and floors of the bridges, retaining walls etc. including setting out,
dressing of sides, ramming of bottom, getting out the excavated material, back filling
in layers with approved material and consolidation of the layers by ramming and
watering etc. including all lift, disposal of surplus soil upto a lead of 300m, all types of
shoring and strutting with all labour and material complete as per drawing and
technical specification as directed by Engineer in charge.
Note: This item will be used for excavation work in connection with other
miscellaneous works also like side drains, foundation for OHE masts and other
miscellaneous structures in connection with Gauge Conversion, Doubling, New lines.
022011 All kinds of soils

Ordinary soil
Unit = cum
Taking output = 10 cum
Mechanical Means
Machinery:
Labour:
Mate (Skilled) Day 0002 609.00 0.32 194.88
1,264.83
1,277.48
1,456.96
1,675.51
Cost of 10 cum 1,692.26
Rate per cum Cum 169.23
022012 Soft rock (not requiring blasting)

Depth upto 3 m
Unit = cum
Machinery:
Rock Excavator (Semi skilled) Day 0014 505.00 0.71 356.03
Rock Breaker (Semi skilled) Day 0015 505.00 1.59 802.95
Labour:
2,645.79
2,672.25
3,047.70
3,504.85
Cost of 10 cum 3,539.90

Code (Rs.) (Rs.)
022013 Hard rock (requiring blasting)
Depth upto 3 m
Unit = cum
Machinery:
Rock Excavator (Semi skilled) Day 0014 505.00 1.06 535.30
Labour:
Material:
Blasting Powder Kg 0171 50.00 3.93 196.50
Blasting Fuse (Fuse Wire) Each 0172 20.00 4.00 80.00
4,807.47
4,855.54
5,537.75
6,368.41
Cost of 10 Cum 6,432.10
022014 Hard rock (blasting prohibited )

Unit = cum
Machinery:
Labour:
7,346.40
7,419.86
8,462.35
9,731.70
Cost of 10 Cum 9,829.02
022020 Extra over item nos. 022011 to 022014 for executing the work under water and/or
liquid mud to compensate all additional arrangements including pumping out water as
required.
Note:
The extra percentage rate is applicable only for the quantity of work executed under
water.

Code (Rs.) (Rs.)
Extra due to slow progress and dewatering of the rate of the item Cum 0.20
022030 Providing and laying in position Plain cement concrete of specified Nominal Mix for
miscellaneous works like side drains, foundation for OHE masts and other
miscellaneous structures excluding the cost of Cement, centering and shuttering -
All work up to plinth level :
022031 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm

nominal size)
Details of cost for 15 cum.
Material:
Coarse Sand (Zone III) Cum 0202 1200.00 6.38 7,656.00
Labour:
Machinery:
Hire charges of Concrete Mixer 0.25 to 0.40 cubic metre capacity Day 0070 800.00 0.75 600.00
Hire charges of 25 KVA Generator Day 0074 1500.00 0.75 1,125.00
Hire charges of Pin Vibrator Day 0079 350.00 0.75 262.50
TOTAL 27,345.45
27,618.90
31,499.36
36,224.26
Cost for 15 Cum. 36,586.51
022032 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm

nominal size)
Material:
Labour:
Machinery:
28,254.70
28,537.25
32,546.73
37,428.74
Cost for 15 Cum. 37,803.03

Code (Rs.) (Rs.)
022033 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm

nominal size)
Material:
0.56 - (7.5% for voids i.e.) 0.04 = 0.52 cum
Labour:
Machinery:
TOTAL 27,898.08
28,177.06
32,135.94
36,956.33
Cost for 15 Cum. 37,325.89
022034 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm

nominal size)
Material:
Portland Cement(0.15674 cum) tonne
Labour:
Machinery:
TOTAL 29,044.20
29,334.64
33,456.16
38,474.58
Cost for 15 Cum. 38,859.33

Code (Rs.) (Rs.)
022035 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm
nominal size).
Material:
(0.70 cum - 7.5% for voids i.e. 0.05 =0.65 cum)
Portland Cement (0.15674 cum) tonne
Labour:
Machinery:
TOTAL 28,259.16
28,541.75
32,551.87
37,434.65
Cost for 15 Cum. 37,808.99
022036 1:4:8 (1 Cement : 4coarse sand (zone-III): 8 graded stone aggregate 40 mm nominal
size).
Material:
(0.70 cum - 7.5% for voids i.e. 0.05 = 0.65 cum)
Portland Cement (0.1175 cum) tonne
Labour:
Machinery:
28,585.78
28,871.64
32,928.10
37,867.32
Cost for 15 Cum. 38,245.99

Code (Rs.) (Rs.)
022040 Providing and laying in position machine batched, machine mixed and machine
vibrated Cement Concrete of specified grade as per approved Design Mix (mixed in
Mobile Concrete Batching/Mixing Plant at site or RMC from approved plants) using
20mm graded crushed stone aggregate and coarse sand of approved quality in RCC
raft foundation & Pile cap including finishing, using Admixtures in approved
proportions (as per IS:9103), to modify workability & other properties without
impairing strength and durability complete as per specifications and direction of the
Engineer in charge. Payment for cement, reinforcement and shuttering shall be paid
extra.
RCC Grade Concrete

Using Mobile Concrete Batching/Mixing Plant
Unit : Cum
Material:
Plasticiser / Super Plasticiser Kg 0192 80.00 202.56 16,204.80
Labour:
Mason 1st class (Skilled) Day 0004 609.00 3.00 1,827.00
Machinery:
Mobile Concrete Batching/Mixing Plant @ 20 cum/hour Hour 0067 1400.00 6.00 8,400.00
Hire charges of Pin Vibrator Day 0079 350.00 4.00 1,400.00
Hire charges of surface vibrator Day 0080 300.00 4.00 1,200.00
Concrete Pump Hour 0068 900.00 6.00 5,400.00
Hire charges of Transit Mixer 4 cum capacity Hour 0069 2140.00 15.00 32,100.00
Total 233,409.00
235,743.09
268,864.99
309,194.74
Cost of 120 Cum 312,286.69
20mm graded crushed stone aggregate and coarse sand of approved quality for the
following Reinforced cement concrete structural elements up to height of 9.0 m from
foundation top level, including finishing, using Admixtures in approved proportions
(as per IS:9103), to modify workability & other properties without impairing strength
and durability complete as per specifications and direction of the Engineer in
charge. Payment for cement, reinforcement, shuttering shall be paid extra.
022051 Abutment & Pier

Rate same as for item 022040 Cum 022040 2602.39 1.00 2,602.39
Additional cost upto 9 mt average height @10% on the cost of labour and Cum 022040 723.40 0.10 72.34
machinery as per analysis item no. 022040 for 1 cum i.e 10% on Cost of labour and
machinery for 120 Cum before adding CPOH, GST etc multiplied by
(1.01*1.1405*1.15*1.01) /120.
Cost per cum Cum 2,674.73


Code (Rs.) (Rs.)
022052 Wing wall and Return wall
Rate sane as item no.022051
022053 Abutment cap, Pier Cap, Inspection Platform & Pedestal over Pier cap, Fender wall,
Diaphragm wall etc.
Rate same as item 022040 Cum 022040 2602.39 1.00 2,602.39
Add extra for height @15% on the Cost of labour and machinery as per analysis of Cum 022040 723.43 0.15 108.51
item no. 022040 for 1 cum i.e 15% on Cost of labour and machinery for 120 Cum
before adding CPOH, GST etc multiplied by (1.01*1.1405*1.15*1.01) /120.
022054 Approach slab at formation level, Dirt wall/ ballast wall at formation level
Rate same as item 022040 Cum 022040 2602.39 1.00 2,602.39
Additional cost for thin section and slanting height @5% on the cost of labour and Cum 022040 723.43 0.05 36.17
machinery as per analysis of item no. 022040 for 1 cum i.e 5% on Cost of labour
and machinery for 120 Cum before adding CPOH, GST etc multiplied by
(1.01*1.1405*1.15*1.01) /120.
022055 Extra for every increase of 1m or part thereof in the height above 9.0 m
Taking output = 120 Cum considering increase in cost of labour and machinery in
proportion of height i.e. 10% per meter.
Additional cost of labour per meter height @10% on Cost of labour and machinery 120 Cum 022040 64884.20 0.10 6,488.42
for 120 Cum as per analysis of item no. 022040 before adding overheads and other
percentages like GST, CPOH etc.
6,553.30
7,474.04
8,595.15
Cost/Cum/mt. height or part thereof Cum 72.34
022060 Providing and laying Plain Cement Concrete 1:3:6 with graded stone aggregate of
40mm nominal size, in foundation and floors, retaining walls of bridges including
mechanical mixing, vibrating, pumping and bailing out water where ever required
with all materials and labour complete but excluding the cost of cement and
shuttering as per drawings and technical specifications as directed by Engineer
CC 1:3:6
Material:
Labour:
Machinery:
Hire charges of surface vibrator Day 0080 300.00 1.00 300.00
28,589.70

Code (Rs.) (Rs.)
28,875.60
32,932.62
37,872.51
Cost of 15 Cum 38,251.24
022070 Providing and fixing Weep Holes in Abutments, Wing walls and Return walls etc., of
new bridges with 110mm dia UPVC pipe Type A ISI marked with all contractor's men,
material, transportation, all taxes as per specifications and as directed by Engineer-in-
Charge.
Unit Each Mts

Taking output = 30 Mts
Material:
uPVC Pipe- type A ISI marked 110mm dia (working pressure 4Kg/cm2) Metre 0260 160.00 31.50 5,040.00
Labour:
Mason 1st class (Skilled) Day 0004 609.00 0.10 60.90
Machinery:
5,194.00
5,245.94
5,982.99
6,880.44
Cost for 30 m 6,949.25
Cost per m Metre 231.64
022080 Boring, providing and installation of bored cast in-situ Reinforced Cement Concrete
piles of specified diameter and length below pile cap of specified grade with Design
Mix Cement Concrete, using 20mm graded crushed stone aggregate and coarse
sand of approved quality, to carry a safe working load not less than specified,
concreting by machine batching, machine mixing, scaffolding, using Admixture in
approved proportion (as per IS:9103), placing with tremie pipe, chipping off of pile
top to remove laitance concrete above cut off level etc., pumping and bailing out
water, by percussion drilling using Direct Mud Circulation (DMC) or Bailor and Chisel
technique by tripod and mechanical Winch machine, complete in all respect as per
approved drawing, specification and direction of the Engineer in charge.
Note:
1. Payment for only cement, reinforcement and permanent casing pipe (if any )
shall be made extra.
2. Length of the pile for payment shall be measured upto the bottom of RCC pile cap.
022081 1500 mm diameter

Unit = metre
Taking output = 9m
Machinery:
Hire and running charges of Tripod and Mechanical Winch machine complete with Day 0062 3000.00 1.54 4,620.00
power unit and accessories etc. and shifting at site including maintenance and cost
of fuel / lubricants & operators for running
Hire and running charges of light crane 5 MT capacity Day 0088 4000.00 0.10 400.00
Hire and running charges of Bentonite pump Day 0064 3000.00 0.96 2,880.00

Code (Rs.) (Rs.)
Bentonite powder MT 0173 4025.00 0.45 1,811.25
Labour:
Misc.:
23,221.74
23,453.96
26,749.24
30,761.62
31,069.24
Cost of concrete (quantity required for 9 m = 15.91 cum) except cement as per item 022040 2602.39 15.91 41,404.01
no. 022040
Cost of 9 m 72,473.25
Rate per metre Metre 8,052.58
022082 1200mm diameter

Pile diameter = 1200mm
Unit = metre
Taking output = 9m
Machinery:
Labour:
Misc.:
16,910.15
17,079.25
19,478.89
22,400.72
22,624.73
no. 022040
Cost of 9 m 49,091.02

Unit = metre
Taking output = 10m
Machinery:

Code (Rs.) (Rs.)
Labour:
Misc.:
15,243.55
15,395.99
17,559.12
20,192.99
20,394.92
no. 022040
Cost of 10 m 40,849.70

Unit = metre
Taking output = 15m
Machinery:
Labour:
Misc.:
13,526.70
13,661.97
15,581.47
17,918.69
18,097.88
no. 022040
Cost of 15 m 37,719.90

Code (Rs.) (Rs.)
Unit = metre
Taking output = 22m
Machinery:
Labour:
Misc.:
12,811.85
12,939.97
14,758.03
16,971.74
17,141.46
no. 022040
Cost of 22 m 33,328.32
022090 Boring, providing and installation of bored cast in-situ Reinforced Cement Concrete
piles using Hydraulic piling Rig of specified diameter and length below pile cap of
specified grade with Design Mix Cement Concrete, using 20mm graded crushed
stone aggregate and coarse sand of approved quality, to carry a safe working load
not less than specified, concreting by machine batching, machine mixing, scaffolding,
using Admixture in approved proportion (as per IS:9103), placing with tremie pipe,
chipping off of pile top to remove laitance concrete above cut off level etc., pumping
and bailing out water complete in all respect as per approved drawing, specification
and direction of the Engineer in charge.
Note:
1. Payment for only cement, reinforcement shall be made extra.
2. Length of the pile for payment shall be measured upto the bottom of RCC pile
Cap.
022091 1500 mm diameter

Unit = metre
Taking output = 9m
Machinery:
Hire and running charges of Hydraulic Piling Rig with power unit etc. including Day 0063 35000.00 0.77 26,950.00
complete accessories and shifting at site
Labour:

Code (Rs.) (Rs.)
Misc.:
45,551.74
46,007.26
52,471.28
60,341.97
60,945.39
no. 022040
Cost of 9 m 102,349.40

Unit = metre
Taking output = 9m
Machinery:
Labour:
Misc.:
36,340.15
36,703.55
41,860.40
48,139.46
48,620.86
no. 022040
Cost of 9 m 75,087.15

Unit = metre
Taking output = 10m
Machinery:

Code (Rs.) (Rs.)
Labour:
Misc.:
35,253.55
35,606.09
40,608.74
46,700.05
47,167.05
no. 022040
Cost of 10 m 67,621.83

Unit = metre
Taking output = 15m
Machinery:
Labour:
Misc.:
33,826.70
34,164.97
38,965.14
44,809.92
45,258.02
no. 022040
Cost of 15 m 64,880.03

Unit = metre
Taking output = 22m
Machinery:

Code (Rs.) (Rs.)
Labour:
Misc.:
34,561.85
34,907.47
39,811.97
45,783.76
46,241.60
no. 022040
Cost of 22 m 62,428.46
022100 Providing, fabricating and installing permanent casing pipe for bored piles for all
diameters with specified thickness of steel plate including all labour, materials, tools
& complete as per approved drawing & specifications complete in all respect as per
the direction of Engineer in charge.
Note: Payment shall be made as per the weight of circular plate of casing pipe only.
Unit = 1 MT
Taking output = 5 MT = 50 qtl
Considering wastage of 5%, quantity required = 50 x 1.05 = 52.50 quintal.
Material:
Structural Steel Plates conforming to Grade Designation E 250; Quality "A" as per IS Quintal 0223 6300.00 52.50 330,750.00
2062
Considering consumables, machinery, tools & plants required for fabrication, placing 0.15 49,612.50
in position etc. @15% of the cost of plate
Labour:
Welder (Skilled) Day 0029 609.00 1.00 609.00
Fitter Grade - 1 (Skilled) Day 0010 609.00 5.00 3,045.00
Blacksmith - 1st Class (Skilled) Day 0008 609.00 5.00 3,045.00
Fitter Grade - 2 (Semi-skilled) Day 0011 505.00 5.00 2,525.00
402,746.50
406,773.97
463,925.71
533,514.56
Rate for 5 MT 538,849.71
Rate per MT MT 107,769.94
022110 Extra for chiselling in addition to boring of piles, if chiselling is required to be

resorted to in hard rock or big stone boulders larger than 30cm, manually or by any
other means.

Code (Rs.) (Rs.)
022111 1200mm diameter pile
Details of cost for 0.5 Cum
Fitter Grade - 2 (Semi-skilled) Day 0011 505.00 0.05 25.25
1,338.25
1,351.63
1,541.54
1,772.77
Details of cost for 0.5 Cum 1,790.50
Qty of chieseling in 1 metre length of pile =22/7*1.2*1.2/4*1=1.13 Cum

Qty of 1M= 22/7*1.0*1.0/4*1=0.786Cum Cum 022111 3580.99 0.79 2,814.66
Add extra for restricted space in working inside the shaft of pile. 0.10 281.47
Rate per meter Metre 3,096.12

Qty of 1 M =22/7*0.8*0.8/4*1 =0.503 cum Cum 022111 3580.99 0.50 1,801.24

Qty of 1 M =22/7*0.6*0.6/4*1 =0.283 cum Cum 022111 3580.99 0.28 1,013.42
022120 Conducting load test of a single pile upto specified capacity in accordance with
IS:2911 (Part-IV) including installation of loading platform and preparation of pile
head or construction of test cap and dismantling of test cap after test etc. with all
labour, material, tool & plants, equipment, machinery, etc. complete as per drawing
and specification, as directed by the Engineer.
022121 Initial load test upto 50 ton capacity pile

Detail of cost of each
Considring requirement of load on loading platform as 150% of pile capacity and
further 25% more for stability of the load, total load required on the platform =
50*1.5*1.25 - 93.75 say 100 mt
Material:
Cost of filled bags including material as sand or earth for kentledge purpose. 1000 nos. 0200 5000.00 2.00 10,000.00
Labour:
(i) For making preparatory arrangement like erecting platform, kentledge etc. for
conducting load test
(ii) labour for clearing the site after completion of the test and removing an disposing
the materials.
30,122.00
Cost of use of platform materials, instrumentation and other incidental charges @ 0.25 7,530.50
25%

Code (Rs.) (Rs.)
37,652.50
38,029.03
43,372.10
49,877.92
Cost of each test Each 50,376.70
022122 Initial load test above 50 ton and upto 100 T capacity pile
further 25% more for stability of the load, total load required on the platform on the
average of the range i.e. 75 T = 75*1.5*1.25 - 140.63 say 140 mt
Material:
Labour:
the materials.
39,725.00
Cost of use of platform materials, instrumentation and other incidental charges @ 0.15 5,958.75
25%
45,683.75
46,140.59
52,623.34
60,516.84
022123 Initial load test above 100 ton and upto 250 T capacity pile
further 25% more for stability of the load, total load required on the platform on the
average of the range i.e. 175 T = 175*1.5*1.25 - 328.125 say 328 mt
Material:
Machinery:
Hire Charges of JCB of 0.92 cum bucket Capacity Hour 0058 800.00 8.00 6,400.00
Labour:
the materials.

Code (Rs.) (Rs.)
55,240.00
Cost of making platforms, instrumentation and other incidental charges @ 15% 0.15 8,286.00
63,526.00
64,161.26
73,175.92
84,152.30
022124 Extra for every increase of 50 ton in pile capacity or part thereof over 250 ton
Additional hours of Loader required for loading and unloading @ 50MT/hour for
increse of average of additional loading of 25 MT, machine hour required for both
loading/unloading i.e. 25MT + 25 MT = 50 MT is 1 hour
Hire Charges of JCB of 0.92 cum bucket Capacity Hour 0058 800.00 1.00 800.00
3,616.00
3,652.16
4,165.29
4,790.08
Rate per every increase of 50 ton. Each 4,837.98
022125 Routine Load Test upto 50 ton capacity pile

50% of Rate of Initial Test of Pile vide item No. 022121 022121 50376.70 0.50 25,188.35
Rate for each test Each 25,188.35
022126 Routine Load Test above 50 ton capacity upto 100 ton capacity pile
022127 Routine Load Test above 100 ton capacity upto 250 ton capacity pile
022130 Lateral load testing of single pile in accordance with "IS Code of practice IS:2911
(Part-IV) for determining safe allowable lateral load of pile” with all labour, material,
tool & plants, equipment, machinery, etc complete as per drawing and specification
as directed by the Engineer
022131 Piles with lateral load capacity of upto 50 ton

Machinery:
Hire Charges of Hydraulic Jack of 50 t capacity for lateral load testing of piles Day 0112 2000.00 2.00 4,000.00
Cost of reusable material for arrangement of reactive force @ 20% of Hire charges 800.00
of jack
Labour:
Blacksmith - 2nd Class (Semi-skilled) Day 0009 505.00 4.00 2,020.00
13,716.00
14,216.00

Code (Rs.) (Rs.)
14,358.16
16,375.48
18,831.80
Rate per Test Each 19,020.12
022132 Piles with lateral load capacity of above 50 ton and upto 100 ton
Machinery:
Hire Charges of Hydraulic Jack of 100 t capacity for lateral load testing of piles Day 0113 5000.00 2.00 10,000.00
Cost of reusable material for arrangement of reactive force @ 20% of Hire charges 0.20 2,000.00
of jack
Labour:
20,916.00
21,616.00
21,832.16
24,899.58
28,634.52
022140 Pulse Echo Test (PET) for integrity testing of piles with contractor’s men, materials
and machines. The rate includes cost of Inspection of site, preparation of pile head
and any other unforeseen cost required for the test, submission of reports in triplicate
as per satisfaction of the Engineer in Charge at site.
Pulse Echo Test (PET) for integrity testing of piles with contractor’s men, materials Each 0111 2000.00 1.00 2,000.00
and machines. The rate includes cost of Inspection of site, preparation of pile head
and any other unforeseen cost required for the test, submission of reports in triplicate
as per satisfaction of the Engineer in Charge at site.

2,100.00
2,121.00
2,419.00
2,781.85
023000 WELL FOUNDATION

023010 Earth work in OPEN excavation in foundation of bridges, for placing of well curbs of
all shapes and designs in all kinds of soil including taking out the excavated soil,
levelling, ramming of bottom of excavation and trimming of sides, returning the soil in
layers, consolidation, disposal of surplus soil within a lead of 300m, including all lift,
dewatering, shoring and strutting complete as per technical specification and as
directed by Engineer in charge. (compaction of surplus soil when led to the bank will
be paid as per relevant item separately).
In all types of soils


Code (Rs.) (Rs.)
Unit = 1 Cum
Rate Same as item no. 022011 169.23 1.00 169.23
Add 50% for excavation in river/stream bed 0.50 84.61
Cost for 1 Cum Cum 253.84
023011 In Ordinary rock

Cost for 1 Cum Cum 389.39
023012 Hard rock (blasting prohibited )

Cost for 1 Cum Cum 1,081.19
023020 Providing and constructing Temporary Earthen Island / coffer dam for construction of
well foundations of dia. upto 10m (longest dimension) , including bailing and pumping
out of water, provision of sand bags, wooden ballies, sheet piling, earth, sand or any
other suitable material, as required with all labour and material complete job.
023021 For water depth upto 1.00m

Providing and Constructing Temporary Island 16 m diameter for construction of Well
Foundation for 8m dia. Well
Assuming depth of water 1.0 m and height of island to be 1.25 m
Unit = 1 No.
Taking output = 1 No.
Material:
Labour:
Machinery:
Hire and running charges of light crane 5 MT capacity Day 0088 4000.00 1.00 4,000.00

36,677.00
37,043.77
42,248.42
48,585.68
Rate for water depth of 1.00m Each 49,071.54
023022 Extra for every 1.00m additional depth and part thereof over item 023021 upto water
depth of 4.00m.
Assuming depth of water 4m and height of island 4.5 mts. Island dia = 16mts
average
Assuming depth of water 4.0 m and height of island 4.5 m
Unit = 1 No.
Taking output = 1No.
Material:
Hollock Ballies 150mm diameter Metre 0481 150.00 95.00 14,250.00

Code (Rs.) (Rs.)
Hollock Ballies 80mm diameter Metre 0480 85.00 190.00 16,150.00
Labour:
Mate (Semi skilled) Day 0003 505.00 5.60 2,828.00
Machinery:
Sundries Lumpsum 9901 1.00 2200.00 2,200.00

216,972.00
219,141.72
249,931.13
287,420.80
Total cost for 4.00m depth of water 290,295.01
Cost for 1.00m depth of water as per item No.023021 Each 023021 49071.54 49,071.54
Extra cost for 3.00m depth of water (A-B) 241,223.47
Cost for 1.00 additional depth of water 80,407.82
Rate per every 1.00m additional water depth or part there of Each 80,407.82
023023 Providing and constructing 10m wide service road to reach island location from one
pier location to another pier location.
Assuming span length of 30 m, width of service road 10m and depth of water 1m
Unit = Running Meter

Taking output = 30 metre
a) Material
b) Labour
c) Machinery
83,357.20
84,190.77
96,019.58
110,422.51
Cost for 30 m 111,526.74
Rate per m RM 3,717.56

Code (Rs.) (Rs.)
023030 Supplying, Fabrication, assembly, erection & placing in position the cutting edge of
well curb with structural steel including MS sheet/Plates of specified thickness for
pier/abutment complete as per approved plans and as per direction of Engineering In
charge including all operations like cutting, bending, straightening, drilling holes,
bolting, riveting, welding, threading, jointing of steel sections including outer and
inner places liners and skin plates, stiffeners, hooks, bottle nuts, bond rods etc. as
per design including all ascent, descents, leads, lifts, handing, re-handling, all other
obstructions whatsoever, diverting channels, pumping / bailing out of water wherever
required including cost of steel such as flats, sheets, angles, steel bars etc. with all
labour and material as a complete job.
Taking Output = 1 MT
Material:
2062
Nut & Bolts with washers of all sizes Kg 0234 80.00 20.00 1,600.00
Electrodes, cutting gas and other consumables @10% of cost of Structural Steel and 0.10 6,775.00
nuts and Bolts above
Labour:
(for cutting, bending, making holes, joining, welding and erecting in position)
91,779.60
92,697.40
105,721.38
121,579.59
023040 Dry/Wet Sinking of Circular Wells (Other than pneumatic method) in all types of
strata except hard rock requiring ballasting, including bailing and pumping out water,
removal of excavated soil with all labour and material required for sinking as per
drawing and direction of the Engineer in charge, disposal of surplus soil in the
adjoining bank/embankment (compaction to be paid separately under the relevant
item).
023041 From initial level of cutting edge & upto 3m depth

Dia of well (assumed) 9 metre Area 63.64
Taking output = 1cum
Depth below bed level upto 3.0 M
Rate of sinking 0.17 m/hour
a) Labour
b) Machinery
Hire charges of 10MT crane with Grab Bucket of 0.75 cum capacity and accessories Day 0087 7000.00 0.75 5,250.00
8,123.70
Add water charges @ 1% + dewatering charges @5% 0.06 487.42
8,611.12
9,820.98

Code (Rs.) (Rs.)
11,294.13
Rate per Meter for 63.64 Cum 11,407.07
023042 Above 3m to 10m depth

Beyond 3 m upto 10m depth
Rate of sinking 0.15/hour
a) Labour
b) Machinery
Hire charges of air compressor 250 cfm capacity with two leads for pneumatic cutters Day 0065 1600.00 0.83 1,328.00
/ hammers
10,750.53
11,395.57
12,996.64
14,946.14

Add 5 % for every additional meter depth of sinking over the rate of sinking for the
previous meter
11 th m 249.16
12 th m 261.62
13 th m 274.70
14 th m 288.43
15 th m 302.86
Total for 5m 1,376.76
Average rate 275.35
Add 20% for kenteledges including supports, loading arrangement and Labour etc 0.20 55.07

Add 7.5% for every additional meter depth of sinking over the rate of sinking for the
previous meter
16 th m 325.57
17 th m 349.99
18 th m 376.24
19 th m 404.45
20 th m 434.79
Average rate 378.21

Add 7.5%for every additional meter depth of sinking over the rate of sinking for the
previous meter

Code (Rs.) (Rs.)
21st m 467.40
22nd m 502.45
23rd m 540.14
24th m 580.65
25th m 624.19
Average rate 542.96

Add 10% for every additional meter depth of sinking over the rate of sinking for the
previous meter
26th m 686.61
27th m 755.27
28th m 830.80
29th m 913.88
30th m 1,005.27
Average rate 838.37

previous meter
31st m 1,105.80
32nd m 1,216.38
33rd m 1,338.01
34th m 1,471.82
35th m 1,619.00
Average rate 1,350.20

previous meter
36th m 1,821.37
37th m 2,049.04
38th m 2,305.17
39th m 2,593.32
40th m 2,917.49

previous meter
41st m 3,282.17
42nd m 3,692.44
43rd m 4,154.00
44th m 4,673.25
45th m 5,257.41
46th m 5,914.58

Code (Rs.) (Rs.)
47th m 6,653.90
48th m 7,485.64
49th m 8,421.35
50th m 9,474.02
Total for 10m 59,008.76
Add 20% for kenteledges including supports, loading arrangement and Labour etc 0.20 1,180.18
023050 Extra for above 50m for every 1m or part thereof over item no 023049
12.5% for every additional meter depth of sinking over the rate of 023049 0.13 885.13
Additional cost for 1m Cum 885.13
023060 Dry/Wet Sinking of Twin D type Wells (Other than pneumatic method) in all types of
strata except hard rock requiring ballasting, including bailing and pumping out water,
removal of excavated soil, with all labour and material required for sinking as per
drawing and direction of the Engineer in charge including disposal of surplus soil in
the adjoining bank/embankment (compaction to be paid separately under the
relevant item).
023061 From initial level of cutting edge & upto 3m depth

Considering twin D tyoe well of size 12X6M
Area= 22/7x6x6/4+6x6 = 64.28 Sqm
Depth below bed level upto 3.0 M
Rate of sinking 0.25m/hour with 2 cranes
a) Labour
b) Machinery
11,868.60
12,580.72
14,348.31
16,500.55

Beyond 3 m upto 10m depth
Rate of sinking 0.225m/hour with 2 cranes
a) Labour
b) Machinery
/ hammers
13,468.60
14,276.72

Code (Rs.) (Rs.)
16,282.59
18,724.98
Rate per Meter fro 64.28 Cum 18,912.23

Add 5 % for every additional meter depth of sinking over the rate of sinking for the
previous meter
11 th m 308.93
12 th m 324.37
13 th m 340.59
14 th m 357.62
15 th m 375.50
Average rate 341.40

previous meter
16 th m 403.67
17 th m 433.94
18 th m 466.49
19 th m 501.47
20 th m 539.08
Average rate 468.93

previous meter
21st m 579.51
22nd m 622.98
23rd m 669.70
24th m 719.93
25th m 773.92
Average rate 673.21

previous meter
26th m 851.32
27th m 936.45
28th m 1,030.09
29th m 1,133.10
30th m 1,246.41

Code (Rs.) (Rs.)
previous meter
31st m 1,371.05
32nd m 1,508.16
33rd m 1,658.97
34th m 1,824.87
35th m 2,007.36

previous meter
36th m 2,258.28
37th m 2,540.56
38th m 2,858.13
39th m 3,215.40
40th m 3,617.33

previous meter
41st m 4,069.49
42nd m 4,578.18
43rd m 5,150.45
44th m 5,794.26
45th m 6,518.54
46th m 7,333.35
47th m 8,250.02
48th m 9,281.28
49th m 10,441.44
50th m 11,746.62
Total for 10m 73,163.62
Add 20% for kenteledges including supports, loading arrangement and Labour etc 0.20 1,463.27
023070 Extra for above 50m for every 1m or part thereof over item no 023069
12.5% for every extra metre beyond 50m depth over 023069 0.13 1,097.45
Additional cost for 1m Cum 1,097.45
023080 Extra for sinking of wells in hard rock requiring controlled blasting including cost of
explosive, detonators, chiselling including all other ancillary works
Taking output = 1m
a) Materials
Blasting Powder Kg 0171 50.00 15.00 750.00
Blasting Fuse (Fuse Wire) Each 0172 20.00 60.00 1,200.00
b) Labour
Rock Breaker (Semi skilled) Day 0015 505.00 0.40 202.00

Code (Rs.) (Rs.)
c) Machinery
/ hammers
29,662.00
Dewatering @5% of cost of b+c 0.05 1,483.10
31,145.10
31,456.55
35,876.20
41,257.63
Rate per Running Meter for 63.64 Cum 41,670.20
vibrated Cement Concrete of specified grade as per approved Design Mix (Cast in-
Situ) using 20mm graded crushed stone aggregate and coarse sand of approved
quality in the following elements of well including finishing, using Admixtures in
approved proportions (as per IS:9103), to modify workability & other properties
without impairing strength and durability complete as per drawings and technical
specifications as directed by Engineer. Payment for cement, reinforcement and
shuttering shall be made extra.
023091 In well Curb

Unit = cum
Rate same as for item no. 022040 2,602.39
Add extra for lift 10% of 022040 0.10 260.24
023092 In Steining of wells

Same as in Item no. 023091 (in well curb) Cum 2,862.63
023093 In Bottom plug for wells including arrangements for placing concrete under water with
tremie or bottom opening skips.
Bottom Plug
Concrete to be placed using tremie pipe
Note: 10% extra cement to be added where under water concreting is involved
Unit = cum
Rate same as for item no. 022040 2,602.39
Add 10 per cent of cost of material and labour towards cost of forming sump, 0.10 260.24
protective bunds, chiselling and making arrangements for under water concreting
with tremie pipe..
023094 In Intermediate/top plug without shuttering

Rate same as Item no. 023093 as reinforcement, cement & shuttering are being paid 2,602.39
separately and in addition to CC rates.
Add extra for thin sections and difficults locations 0.05 130.12
Rate per cum Cum 2,732.51
023095 In Intermediate/Top plug with internal shuttering

Rate same as Item no. 023094 as reinforcement, cement & shuttering are being paid 2,732.51

Code (Rs.) (Rs.)
023096 In Well cap and corbel, if provided
Rate same as item no 023095 as reinforcement, cement & shuttering are being paid 2,732.51
023100 Supplying and filling ordinary sand in between bottom plug and top plug in wells
including all lead lift handling, re-handling, as a complete job as per specification and
guidelines.
023101 Using Sand from River Bed if suitable for filling

Unit = Cum
Rate as per item no. 022011 Cum 169.23
Add for working under water, ramming in layers and submerging well as required 0.50 84.61
023102 Using sand from other than River bed (This item is to be operated if suitable sand is
not available in River Bed for filling
Unit = Cum
a) Materials
Fine Sand (Zone IV) Cum 0203 1000.00 1.20 1,200.00
b) Labour
1,334.35
1,347.69
1,537.04
1,767.60
Rate per Cubic Meter 1,785.28
024000 RCC BOX

024010 Providing and casting machine batched, machine mixed and machine vibrated
Cement Concrete of specified grade as per approved Design Mix, mixed in Mobile
Concrete Batching/Mixing Plant at site or RMC from approved plants, (Cast in-
Situ/Pre-cast) in bottom/top slab, side walls, toe wall and sumps haunch filling head
walls, thrust bed or any other component using 20mm graded crushed stone
aggregate and coarse sand of approved quality of RCC box of any size including
finishing, Admixtures in approved proportions (as per IS:9103), to modify workability
& other properties without impairing strength and durability, complete as per
drawings and technical specifications as directed by Engineer in charge.
Note: Payment for cement, reinforcement and shuttering shall be made extra.
Rate same as item no. 022040 2602.39 1.00 2,602.39

Add 10% extra for placing of Concrete in thin sections and multiple pours of concrete 0.10 260.24
and congested area
Cost per 1 Cum Cum 2,862.63

Code (Rs.) (Rs.)
vibrated Design Mix Cement Concrete, mixed in Mobile Concrete Batching/Mixing
Plant at site or RMC from approved plants, of specified grade (cast in-situ) using
20mm graded crushed stone aggregate and coarse sand of approved quality in Drop
and curtain wall and alike structures below bed level, complete in all respect as per
drawings and technical specifications to the satisfaction of Engineer-in-Charge.
Note:Payment for cement, reinforcement and shuttering shall be made extra.
Rate as per item no. 022040 Cum 022040 2,602.39
Rate per 1 Cum Cum 2,602.39
024030 Launching of precast RCC box segments of any size and barrel length for
single/double line as per approved drawings to the correct alignment and position in
electrified / non-electrified sections safeguarding all utilities ( S&T cable, power
cable, OHE, pipelines etc.) including transportation of box segments from casting
yard to site of launching, dismantling of the existing track, removing & stacking of
ballast, removing surcharge, dismantling of existing bridge built with stone masonry /
cement concrete, placing of Box segments in position either on base slab or
prepared foundation, backfilling after launching of precast box segment and
compaction of earth in surcharge, ballasting & re-laying of track to correct alignment
and geometry, packing and further maintenance till allowing non-stop 20 KMPH over
the re-laid track, complete in all respect as per approved drawing to the satisfaction
of Engineer-in-charge. The rate is all inclusive except the cost of RCC Box
Segments, Base Slabs (if required) and backfill material which shall either be
supplied by railway or paid extra under relevant item.
Note: Unit of 'Each' here means bridge of span(s) with a total linear waterway upto
3m.
024031 Single Line

Note: Minimum equipment required shall be (i) Crawler mounted Hydraulic excavator
of min 200 HP and bucket capacity 2.5 cum - 3 numbers (ii) Cranes minimum 150 T
capacity - 3 nos., (iii) Stone Breaker - 1 no., (iv) Road Trailor of 20 MT capacity - 1
no., (v)Tippers - 2 nos. and (vi) Tractors - 2 nos. (vii) Slope Vibratory compactor - 1
no. and other required machineries etc. in good working condition at site of work.
Machineriy:
{Considering wastage of machinery-days in transportation to site of work as 50%,
total nos. for Excavator = 4.5, for Hammer Drill / Compressor = 1.5, for Tipper = 3
and for JCB = 3}
Crawler mounted Hydraulic Excavator 200 HP (2.5 cum bucket) Day 0045 16000.00 4.50 72,000.00
/ hammers
Hire charges of Power driven hammer drill Day 0083 1500.00 1.50 2,250.00
total nos. for Cranes = 4.5 and for Trailer = 1.5}
Hiring charges of 150 MT capacity crane Day 0097 100000.00 4.50 450,000.00
For compaction of surcharge after placement of box
Hire Charges of Slope Vibrator to be attached to Hydralic Excavator for rolling of Day 0054 2000.00 1.00 2,000.00
slope surfaces of embankment.
Labour:
Mate (Skilled) Day 0002 609.00 3.00 1,827.00
602,970.00

Code (Rs.) (Rs.)
608,999.70
694,564.16
798,748.78
Cost for Single Line Each 806,736.27
024032 Double Line

Note: Minimum equipment required shall be (i) Crawler mounted Hydraulic excavator
of min 200 HP and bucket capacity 2.5 cum - 3 numbers (ii) Cranes minimum 200 T
capacity - 3 nos., (iii) Stone Breaker - 1 no., (iv) Road Trailor of 20 MT capacity - 1
no., (v)Tippers - 2 nos. and (vi) Tractors - 2 nos. (vii) Slope Vibratory compactor - 2
nos. and other required machineries etc. in good working condition at site of work.
Machineriy:
total nos. for Excavator = 4.5, for Hammer Drill / Compressor = 1.5, for Tipper = 3
and for JCB = 3}
/ hammers
total nos. for Crane days =4.5 and for Trailer = 1.5}
For compaction of surcharge after placement of box
Hire Charges of Slope Vibrator to be attached to Hydralic Excavator for rolling of Day 0054 2000.00 2.00 4,000.00
Labour:
Mate (Skilled) Day 0002 609.00 5.00 3,045.00
963,446.00
973,080.46
1,109,798.26
1,276,268.00
Cost for Double Line Each 1,289,030.68
025000 MISCELLANEOUS
025010 Deduct if 40mm graded stone aggregate is used in place of 20mm graded stone
aggregate in any grade of concrete. (deduction to be made for quantity of concrete)
Material:
Difference of Cost of 40mm and 20mm size stone aggregates -71.00
Add for Water Charges @ 1% Lumpsum 9902 0.01 -0.71

Code (Rs.) (Rs.)
-71.71
Add for GST @ 12% (multiplying factor 0.1405) Lumpsum 9903 0.14 -10.08
-81.79
Add for Contractor’s Overheads and Profit @ 15% Lumpsum 9904 0.15 -12.27
-94.05
Add for Cess @ 1% Lumpsum 9905 0.01 -0.94
Cost per Cum Cum -94.99
025020 Providing and applying two coats of coal tar or bitumen confirming to IS:3117– latest
version on the top and sides of RCC box/slabs @ 1.70 kg/sqm after cleaning the
surface with all labour and materials complete job as directed by the Engineer.
Details of cost for 10 sqm

Material:
Industrial grade blown type Petroleum Bitumen of grade 85/25 as per IS:702 MT 0316 47000.00 0.02 799.00
Kerosene Oil Litre 0185 56.00 1.00 56.00
Fuel wood Quintal 0345 4000.00 0.04 140.00
Labour:
1,230.50
1,242.81
1,417.42
1,630.03
Cost of 10 sqm 1,646.33
Cost per Sqm Sqm 164.63
025030 Centering and shuttering including strutting, propping etc. and removal of form for :
025031 All types of bridge sub-structures, e.g. pier, abutment, wing wall, retaining wall, RCC
box type foundations, Abutment cap, Pier Cap, Inspection Platform & Pedestal over
Pier cap, Fender wall, Diaphragm wall etc. upto 5m above ground level
Details of cost for 10 sqm:

Material:
Wall form Panel 1250mm x 450mm (Shuttering material) Each 0255 1150.00 20.00 23,000.00
MS tube 40mm dia (Shuttering material) Metre 0254 293.25 20.00 5,865.00
100mm channel shoulder 2.5 m long (Shuttering material) Each 0253 1322.50 8.00 10,580.00
Adjustable telescopic prop 3m (2.02m-3.75m) (Shuttering material) Each 0256 1265.00 8.00 10,120.00
Beam Clamp 300-380mm (450mm-1070mm) (Shuttering material) Set 0257 454.25 12.00 5,451.00
Total Cost of Making new Shuttering "A". 55,016.00
Considering the above shuttering material can be used 40 times, Cost of using Once 1,375.40
G.I. Binding wire Kg 0222 51.75 2.00 103.50

Cadmium plated full threaded steel screws (30mm x 4mm dia) (Shuttering material) 100 nos. 0258 35.65 1.00 35.65
Aluminium washer 2mm thick & 15 mm dia (Shuttering material) 100 nos. 0259 28.75 1.00 28.75
Labour:
Total "B" 4,451.30
4,495.81

Code (Rs.) (Rs.)
5,127.47
5,896.60
Cost of 10 sqm 5,955.56
Cost per sqm Sqm 595.56
025032 All types of bridge super-structures, e.g. slabs, I-girders, T-girders, Box girders etc.
upto 5m above ground level.
Details of cost for 10 sqm:
Materials:
Cost of Shuttering Material:
Wall form Panel 1250mm x 450mm (Shuttering material) Each 0255 1150.00 20.00 23,000.00
100mm channel shoulder 2.5 m long (Shuttering material) Each 0253 1322.50 8.00 10,580.00
Beam Clamp 300-380mm (450mm-1070mm) (Shuttering material) Set 0257 454.25 12.00 5,451.00
Sub-Total: 71,001.00
Material:
Considering the above shuttering material can be used 40 times, Cost of using Once, 1,775.03
G.I. Binding wire Kg 0222 51.75 2.00 103.50

Cadmium plated full threaded steel screws (30mm x 4mm dia) (Shuttering material) 100 nos. 0258 35.65 1.00 35.65
Aluminium washer 2mm thick & 15 mm dia (Shuttering material) 100 nos. 0259 28.75 1.00 28.75
Labour:
(Labour element has been increased by 25% of substructure due to slow progress of
work)
5,786.93
5,844.79
6,665.99
7,665.89
Cost of 10 sqm 7,742.54
Cost per sqm Sqm 774.25
025033 Extra for additional height over item no. 025031 & 025032 wherever required with
adequate bracing, propping etc. over initial height of 5 metres for every additional
height of 1 metre or part thereof.
Detail of cost for 10 sqms of shuttering for average height of 10 metres - initial
heights 5 metres = 5 metres extra height
Materials
26,910.00
Considering the above shuttering material can be used 40 times, Cost of using Once 672.75

Labour:
3,580.75

Code (Rs.) (Rs.)
3,616.56
4,124.68
4,743.39
Cost of 10 sqm for 5 mt. height 4,790.82
Cost per sqm for 1 metre height Sqm 95.82
vibrated Design Mix Cement Concrete of specified grade (Cast in-Situ) using 20mm
graded crushed stone aggregate and coarse sand of approved quality in jacketing of
piers and abutments from bottom of foundation upto a height of 10m including
finishing for designed thickness of jacketing. Payment for reinforcement, cement,
wire mesh, shuttering, drilling of holes and insertion of rods will be made extra.
Considering 10 sqm surface preperation.and thickness of 30 cm

Labour:
1,250.75
1,263.26
1,440.75
1,656.86
Cost of 10 sqm 1,673.43
Assuming 30 cm thickness of Jacketing. Qty of Concrete = 3 Cum. Rate as per item 2602.39 3.00 7,807.17
022040
9,480.59
Add extra for thinner section, low volume, difficult location and complications involved 0.40 3,792.24
in river bed.
Cost per Cum Cum 4,424.28
025041 Extra for drilling 32mm dia. holes for jacketing / anchoring
Taking out put 50 mts.
Labour:
Machinery:
Hire charges of air compressor 250 cfm capacity with two leads for pneumatic cutters Day 0065 1600.00 0.50 800.00
/ hammers
4,247.00
4,289.47
4,892.14
5,625.96
Cost for 50 mts. 5,682.22
Rate per Metre Metre 113.64

Code (Rs.) (Rs.)
025042 Extra for inserting of dowel bars of specified dia. (cost of rods to be paid extra)
Taking output 200 M
Labour:
1,892.00
1,910.92
2,179.40
2,506.31
Cost for 200 M 2,531.38
025050 Supplying, spreading and compacting well graded hard stone of 63mm average size
(maximum upto 80mm size) in the bottom of foundation of box culverts, bridges etc.
including all lead, lift, ascent, descent etc. complete job as per directions of Engineer
In-charge.
Details of cost for 100 Cum

Material:
Stone Aggregate (single size) 63mm nominal Cum 0205 900.00 100.00 90,000.00
Labour:
99,225.00
100,217.25
114,297.77
131,442.44
Cost for 100 Cum 132,756.86
Cost for 1 Cum Cum 1,327.57
025060 Supply and using Cement at Worksite

025061 Ordinary Portland Cement 43 grade approved brands/makes
Details of Cost per 1 MT
Material:
Ordinary Portland Cement 43 grade MT 0188 4940.00 1.00 4,940.00

4,989.40
5,690.41
6,543.97
Rate Per 1 MT MT 6,609.41
025062 Ordinary Portland Cement 53 grade of approved brands/makes

Material:

Code (Rs.) (Rs.)

5,050.00
5,759.53
6,623.45
025063 Pozzolana Portland Cement approved brands/makes

Material:
Pozzolana Portland Cement MT 0190 4700.00 1.00 4,700.00

4,747.00
5,413.95
6,226.05
025064 Sulphate Resisting Cement approved brands/makes

Material:
Sulphate Resisting Cement MT 0191 6500.00 1.00 6,500.00

6,565.00
7,487.38
8,610.49
025070 Steel reinforcement of approved brands/makes for R.C.C. work including

straightening, cutting, bending, placing in position and binding all complete
025071 Mild steel bars
Details of cost for 1 quintal
Material:
Mild steel bars = 1.00 quintals
Wastage 5% = 0.05 quintals
Total = 1.05 quintals
MS round bar for reinforcement- average rate for various dia Quintal 0220 3600.00 1.05 3,780.00
Cover Blocks @ 1.5% of cost of reinforcement steel Lumpsum 56.70
Labour:
For straightening, cutting, bending, binding and placing in position-
Blacksmith - 1st Class (Skilled) Day 0008 609.00 1.00 609.00
Sundries and binding wire Lumpsum 9901 1.00 50.00 50.00
Sub - Total 4,926.70
4,975.97
5,675.09

Code (Rs.) (Rs.)
6,526.35
Cost for 1 Qtl 6,591.62
Rate per Kg Kg 65.92
025072 Thermo-Mechanically Treated bars of grade Fe-500D or more of approved

brands/makes.
Details of cost for 1 quintal
Material:
Mild steel bars = 1.00 q
Wastage 5% = 0.05 q
Total = 1.05 q
Thermo Mechanically Treated Bars grade Fe 500D - or more.(Average of dia Quintal 0221 5974.00 1.05 6,272.70
10mm to 25mm) without GST
Cover Blocks @ 1.5% of cost of reinforcement steel Lumpsum 94.09
Labour:
For straightening, cutting, bending, binding and placing in position-
Sundries and binding wire Lumpsum 9901 1.00 50.00 50.00
7,456.79
7,531.36
8,589.51
9,877.94
Cost for 1 Qtl 9,976.72
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 3: Bridge Works (Super-structure)
CHAPTER - 3 : Bridge Works Super Structure- RCC

Code (Rs.) (Rs.)
20mm graded crushed stone aggregate and coarse sand of approved quality for cast
in-situ Prestressed (Post-tensioned) concrete girder / Box girders/Slabs for different
spans including finishing, using Admixtures in approved proportions (as per IS:9103),
to modify workability & other properties without impairing strength and durability
complete as per drawings, specifications and direction of the Engineer in-charge.
Payment for Staging, Shuttering, Cement, reinforcement, HTS cables, sheathing,
anchorage cones, stressing of cables and grouting of the ducts shall be made extra
under relevant items.
031011 With Soffit level upto 9m above Bed level

RCC Grade Concrete `
Using Mobile Concrete Batching/Mixing Plant
A) Basic Cost of Concrete
Material:
Plasticiser / Super Plasticiser Kg 0192 80.00 202.56 16,204.80
Labour:
Machinery:
Mobile Concrete Batching/Mixing Plant @ 20 cum/hour Hour 0067 1400.00 6.00 8,400.00
Hire charges of Pin Vibrator Day 0079 350.00 4.00 1,400.00
Hire charges of surface vibrator Day 0080 300.00 4.00 1,200.00
Concrete Pump Hour 0068 900.00 6.00 5,400.00
Hire charges of Transit Mixer 4 cum capacity Hour 0069 2140.00 15.00 32,100.00
233,409.00
235,743.09
268,864.99
309,194.74
Cost of 120 Cum 312,286.69
Basic Rate per Cum Cum 2,602.39 A
B) Additional cost upto 9 mt height @15% on the basic cost of labour and Cum 031011 723.43 0.15 108.51 B
machinery for 1 Cum,
i.e 15% on Cost of labour and machinery for 120 Cum before adding CPOH, GST etc
multiplied by (1.01*1.1405*1.15*1.01) /120.
Rate per Cum upto 9m height Cum 2,710.90
031012 With Soffit level From 9m above Bed Level to12m above Bed Level
Cost of concrete as per item 031011 up to 9 m 2,710.90
Average increase in height beyond 9 metres = (9+12)/2 - 9 m = 1.5 m
Additional cost as per item no. 022055 for 1.5 m height Cum 022055 72.34 1.50 108.51

Code (Rs.) (Rs.)
031013 With Soffit level From 12m above Bed Level to 15m above Bed Level
Cost of concrete as per item 031011 up to 9 m 2,710.90
Average increase in height beyond 9 metres = (15+12)/2 - 9 m = 4.5 m
Additional cost as per item no. 022055 for 4.5 m height Cum 022055 72.34 4.50 325.54
031014 Extra over USSOR Item no. 031013 for Soffit level beyond 15m above Bed Level for
every 1m or part thereof
Same rate as per item no. 022055 Cum 022055 72.34 1.00 72.34
Rate per cum per metre height Cum 72.34
031015 Deduct for casting of Slab in place of Girders (for any heights)
Deduct 5% for casting of slabs in place of girders for any height on the Cost of Cum 031011 723.43 -0.05 -36.17
labour and machinery of item 031011 for 1 cum,
i.e 5% of basic Cost of labour and machinery for 120 Cum before adding CPOH,
GST etc multiplied by (1.01*1.1405*1.15*1.01) /120.
Cost per cum Cum -36.17
031020 Providing and launching in position machine batched, machine mixed and machine
Precast Prestressed (Post-tensioned) Concrete Girder/Box Girders/Slabs in
contactor’s casting yard in the vicinity of worksite, including finishing, using
Admixtures in approved proportions (as per IS:9103), to modify workability & other
properties without impairing strength and durability, complete as per drawings,
specifications and direction of the Engineer.
Note:
1. Payment for Shuttering, Cement, Reinforcement, HTS cables, Sheathing,
Anchorage Cones, stressing of cables, grouting of the ducts and launching of
girder/slab in position shall be made extra under relevant items.
2. For pre-cast item, loading in transport vehicle in casting yard is included and shall
not be paid extra.
Rate Per 1 Cum of Concrete

Basic cost of concrete as of item 031011 Sub Total (A) Cum 031011 2,602.39
031021 Deduct from 031020 for casting of Slab in place of Girder/Box

Deduct for less cost of labour and machinery for casting of slabs in place of girders
for any height
Basic cost for Labour and machinery for 1 cum as of item 031011 Sub Total (A) cum 729.87
Deduction 5% for Lesser cost in slabs than beams and girders cum -0.05 -36.49
Cost per cum Cum -36.49
031030 Providing and launching in position machine batched, machine mixed and machine
Precast Prestressed (Pre-tensioned) concrete girder/slab in contractor’s casting yard,
including finishing, using Admixtures in approved proportions (as per IS:9103), to
modify workability & other properties without impairing strength and durability,
complete as per specifications and direction of the Engineer.
Note:
1. Payment for Shuttering, Cement, Reinforcement, HTS cables including stressing
and launching of girder/slab in position shall be made extra under relevant items.
2. For pre-cast item, loading in transport vehicle in casting yard is included and shall
not be paid extra.

Code (Rs.) (Rs.)
Rate per 1 Cum of Concrete
Rate Same as item no. 031011 Sub Total (A)
031031 Deduct from 031030 for casting of Slab in place of Girder

Deduct for less cost of labour and machinery for casting of slabs in place of girders
for any height
Basic cost for Labour and machinery for 1 cum as of item 031011 Sub Total (A) 723.40
Deduct 5% for lesser cost in slabs than beams and girders -0.05 -36.17
Rate per cum Cum -36.17
031040 Providing, fabricating & fixing in position to exact design profiles, H.T.S. cables of all
classification made from Low Relaxation strands conforming to IS:14268– latest
version in Prestressed (Post-tensioned) Concrete girders/slabs etc. including
supplying, cutting, making into cables with necessary spacers, colour coding,
protecting with water soluble oil at all time, anchoring of cables, supplying and placing
spiral corrugated type galvanized metal steel ducts sheathing made up of Cold
Rolled Cold Annealed (CRCA) mild steel conforming to IS:513 of required diameter/
thickness, vent pipe, placing, bending, routing, fixing, stressing & grouting of cable
ducts with cement grout, Anchorage sets in required number with provision for future
prestressing if any including all lead and lift with contractor’s own materials, labour,
equipments etc. complete as per drawings & specifications. Rate also includes
covering anchorage pads with epoxy mortar of approved quality to avoid corrosion.
Cement for grouting to be paid separately. Payment shall be made in terms of weight
of HTS cables as per drawing.
Unit = 1 MT
Taking output for 18.30m span 2 Girder system RDSO Drg = 1.269MT including
wastage of 10%. Weight without wastages = 1.269/1.1=1.15 MT
Details of cost for 19T13 strand 19 m long cable

Material:
Low relaxation H T Strands conforming to IS 14268 latest version for prestressed MT 0216 57000.00 1.27 72,333.00
concrete
(Wastage 10% considered)
CRCA Sheathing Metre 0217 165.00 190.00 31,350.00
Tube anchorage set complete with bearing plate , permanent wedges etc. Each 0219 1320.00 20.00 26,400.00
Cement for grouting including 3 per cent wastage @ 3.00 kg/m = 3 x 1.03 x 152 = MT 0.47
469.68 kg (say, = 470 kg)
Labour:
(i) For making and fixing cables, anchorages
(ii) For prestressing
Fitter Grade - 1 (Skilled) Day 0010 609.00 1.00 609.00
(iii) For grouting
Machinery:
Hire charges of stressing jack with pump for stressing of HTS cables in PSC Day 0109 11500.00 0.50 5,750.00
girders/slabs.
Hire charges of grout pump with agitator and accessories Hour 0110 500.00 2.00 1,000.00
Hire charges of Generator of 250 KVA capacity Day 0077 3000.00 0.60 1,800.00
146,449.00

Code (Rs.) (Rs.)
147,913.49
168,695.34
193,999.64
Cost of 1.15 MT 195,939.63
031050 Providing, fabricating & fixing in position to exact design profiles, H.T.S. cables of all
classification made from Low Relaxation strands conforming to IS:14268– latest
version in Pretensioned Prestressed Concrete girders/slabs etc. including supplying,
cutting, making into cables with necessary spacers, colour coding, protecting with
water soluble oil at all time, placing, bending, routing, fixing, stressing including all
lead and lift with contractor’s own materials, labour, equipments etc. complete as per
drawings & specifications. Payment shall be made in terms of weight of HTS cables
as per drawing.
Unit = 1 MT
Taking output for PSC Slab 1.000 MT including wastage of 10%. Weight with
wastages = 1.10MT
Materials:
Low relaxation H T Strands conforming to IS 14268 latest version for prestressed MT 0216 57000.00 1.10 62,700.00
concrete
(Wastage 10% considered)
Labour:
(i) For making and fixing cables
(ii) For prestressing
Machinery:
Hire charges of stressing jack with pump for stressing of HTS cables in PSC Day 0109 11500.00 0.50 5,750.00
girders/slabs.
75,056.30
Add 10% of total cost for component of stressing frame Lumpsum 0.10 7,505.63
82,561.93
83,387.55
95,103.50
109,369.02
Cost of 1.00 MT 110,462.72
031060 Extra for using HDPE sheathing in place of CRCA sheathing

HDPE Sheathing Metre 0218 275.00 1.00 275.00
CRCA Sheathing Metre 0217 165.00 1.00 -165.00
Difference of cost of HDPE and CRCA sheathing 110.00
111.10
126.71
145.72

Code (Rs.) (Rs.)
031070 Making suitable designed staging for cast in-situ PSC girders/slabs upto 10.5m
height from bed level upto soffit of girder/slab with all contractors materials,
machinery, tools and plants, transportation complete in all respects required for
casting and removal of the same after completing the work and restoring the site to
original. The payment for staging shall be made on the cubical quantity of main
Girders/slabs.
Considering cost of staging for 24.4 m PSC Box girder (Concrete qnty: 160.00 Cum)
Material:
Concrete Pedestal for CC cribs as per item no. 022060 Cum 022060 2550.08 18.00 45,901.48 A
(PCC 1:3:6) 10.00x4.00x2.00 x 0.75x0.30
(18.00x4.49/20=4.041 MT)
Quantity of steel used in CC crib and ISMB/ISMC support for centering and
shuttering.
1. CC Cribs 244 Nos @ 180kg each =244*180/100 = 439.20 q
2. ISMB 200 length 66m @ 24.2kg/m = 66 x 24.2/100 =15.97 q
3. ISMC 100 length 120m @ 9.56kg/m =120x9.56/100 =11.47q
Total weight = 439.20+15.97+11.47 = 466.64 q.
Considering 25% salvage value and number of uses befire being unserviceable as 20
time, the weight to be charged for using once = 0.75 x 466.64/20 = 17.499 Say 17.50
q.
Considering fabrication cost of crib as 50% of the cost of steel, the quantity of steel to
be charged for using once = 1.50 x 17.50 = 26.25 q
Structural steel such as T, Angles, Channels and R S Joists conforming to Grade Quintal 0224 4950.00 26.25 129,937.50
Machinery:
Transportation of cribs to site of work (One truck, 3 days each for transportation to
site and back after dismantling
Hire charges of 12 MT Hydra Day 0090 5000.00 4.00 20,000.00
Labour:
Total 276,301.52
Total except A 230,400.04
232,704.04
265,398.96
305,208.80
Total except A with water charges, overheads etc. 308,260.89
Cost including A with water charges, overheads etc. 354,162.37
Cost for 160 Cum (24.4 metres span) 354,162.37
031080 Supplying and laying in position specified grade precast prestressed cement concrete
ballast retainers of size, as directed by Engineer In-charge. Payment for Shuttering,
Cement, reinforcement, HTS cables, anchorage cones, stressing of cables and
grouting of the ducts will be done extra.
Rate Per 1 Cum of Concrete

Rate Same as item no. 031011 Sub Total (A)

Code (Rs.) (Rs.)
031090 Design, manufacturing, supplying and fixing in position elastomeric bearing true to
line and level conforming to IS:3400, IS:226, BS-5400 under prestressed concrete
girders/ Steel Girders, for Pre-cast as well as cast-in-situ girders as per approved
drawing. The rate shall include cost of load test of one no. bearing from Railway
approved firms and all fixing materials, equipments, machineries, labour, taxes,
loading, unloading, leading, lifting etc. complete. Rates include getting the drawing
approved from Railway and cost of inspection during manufacturing from railway
approved organization.
Note : 1. The rate is for finished item complete and paid only after fixing in position
below the girder. 2. The volume shall be given in the drawing and no deduction shall
be made for inserted steel plates etc.
Considering an elastomeric bearing of size 500 x 400 x 96 mm for this analysis.
Overall volume of 6 bearings : 19200 X6=115200 cu.cm

Volume of 6 nos. 488mm x 388mm x 4mm size reinforcing steel plates = 4545 cu.cm.
Hence volume of elastometer = 14655 cu.cm.

Material:
Elastomeric bearing assembly consisting of 7 layers of Elastomer bonded to 6 nos. Each 0269 15360.00 1.00 15,360.00
internal reinforcing steel laminates by the process of vulcanisation, complete with all
components as per drawing and Technical Specification (Each of 19200 Cu Cm)
Labour:
Machinery:
Hire charges for 200 MT capacity Jack Day 0107 1500.00 0.50 750.00
Sudries, adhesives misc. T & P and consumables Lumpsum 9901 1.00 500.00 500.00
17,160.30
17,331.90
19,767.04
22,732.09
Cost of volume of elastometer = 19200 cu.cm. 22,959.41
Rate per cucm Cu Cm 1.20
031100 Providing and fixing in position of standard preformed sealed and slab type or strip
seal elastomeric type expansion joints for Railway bridge or Road Over Bridges as
per approved drawings and latest MOST/IRC specifications complete in all respect as
directed by Engineer in-charge.
031101 For 40mm expansion

Taking output = 12 m
Material:
Supply of complete assembly of strip seal expansion joint for 40mm expansion , Metre 0328 4000.00 12.00 48,000.00
comprising of edge beams, anchorage, strip seal element and complete assembly as
per approved specification and drawings
Add 5 per cent of cost of material for anchorage reinforcement, welding and other 0.05 2,400.00
incidentals.
Labour:
55,130.20
55,681.50

Code (Rs.) (Rs.)
63,504.75
73,030.47
Cost of 12 m 73,760.77

Material:
incidentals.
Labour:
75,760.50
76,518.11
87,268.90
100,359.23
Cost of 12 m 101,362.83

Unit = Running meter
Material:
incidentals.
Labour:
90,163.30
91,064.93
103,859.56
119,438.49
Cost of 12 m 120,632.87

Unit = Running meter
Material:

Code (Rs.) (Rs.)
incidentals.
Labour:
111,126.60
112,237.87
128,007.29
147,208.38
Cost of 12 m 148,680.46
031110 Load testing of one or more spans of bridge as selected by the Engineer as per
approved load test procedure following relevant IS/IRC/Railway codes with
contractor’s labour, deflection measuring instruments, loading materials, recoding and
analyzing the load testing results including all lead & lift, etc. complete as required.
The rates are all inclusive and will be paid after load test is finished and girder is
cleared of the kentledges/loading material etc. The load shall be 1.25 times the
stipulated design load.
031111 For Span design load upto 100 MT

Considring the load as 100 mt
Material:
Add 5 per cent of cost of material for anchorage reinforcement, welding and other 0.05 750.00
incidentals.
Hire charges and cost of instrumentation Lumpsum 9901 1.00 750.00 750.00
Labour:
(i) For making platform and loading
(ii) For clearing the site after completion of the test and removing an disposing the
materials.
55,510.00
56,065.10
63,942.25
73,533.58
Rate per test Each 74,268.92
031112 Extra for every increase 1 MT or part thereof in the span design load capacity upto
800 MT

Code (Rs.) (Rs.)
For 9 MT
Additional per MT shall be only due to adding and removing sand bags or any other
items for loading. One person can carry 4.5 MT in a day and both for to and fr
movement it will be 4.5/2 = 2.25 MT. Thus for 9 MT, 4 nos. coolie will be required.
Labour:
1,741.24
1,985.88
2,283.77
Cost of 9 MT 2,306.60
Rate per MT MT 256.29
031120 Casting and installation of single/twin RCC box of all sizes with or without common
web section including design of pushing scheme, thrust bed, casting of all RCC
components, with specified grade of controlled concrete, pushing it in correct position
and alignment below Railway track/Road following all measures of track safety by
“Box pushing technique" as per approved drawings/scheme, with or without
surcharge in all types of soils with disposal of surplus earth away from vent up to 1
Km, fixing arrangement for all services & utilities including parapet walls on both
sides,wearing course, foot paths, plaques, drainage arrangements etc. and all other
incidental works to complete the ROB/RUB/Canal crossing in all respect as per
specifications to the satisfaction of Engineer-in-Charge.
Note:
1. The rate includes all items of work/supplies for complete job in all respects except
"cost of Reinforced cement concrete, cement, reinforcement & shuttering" of (i) main
RCC Box; (ii) Thrust Bed; (iii) Footpath and (v) wearing Course only, which shall be
paid extra under relevant items of USSOR.
2. The payment for this item shall be made for the clear inner cross section area of
the parent RCC Box/Boxes per unit barrel length i.e. clear inner volume of parent
RCC Box/Boxes.
(A) Single RCC Box (Single Vent Way) of 5.50m x 5.00 m

Barrel Length 35.3 m i.e. clear inner volume of 5.5 x 5.0 x 35.3 cum = 970.75 cum
Box Dimensions
Clear span: 5.50M
Height of the box : 5.0M
Wall thickness: 60 cm
Slab thickness: 60 cm
Barrel length for three track of BG (34.8+35.8)/2=35.3m
Inside dimensions of box: 5.5 X5.0 X35.3m
Out side dimenshions of box: 6.7 X6.35 X 35.3m
Thrust Bed Dimensions
Length of thrust bed: 34.8 Mts
width of thrust bed: 7.6 mts
Thickness of thrust bed: 0.75 Mts
Cost of Box pushing except the cost of concrete, cement, reinforcement & shuttering
of RCC Box and Thrust Bed.
Earth work in excavation all types of soil and disposal of surplus soil upto a lead of Cum 022011 169.23 3937.68 666,359.29 A
50 M as per item no. 022011
(i) for thrust bed ( 34.80 X 7.60 X 8.00) = 2115.84
(ii) For Box Portion ( 6.70 X6.35 X 35.30) = 1501.84
(iii ) for approach formation ( 8.00 x20.00 x2.00) =320.00

Code (Rs.) (Rs.)
Leading of excavated earth up to 1km i.e. average lead of 0.5 km. Cost as per 50% Cum 012015 3.12 2756.38 8,605.02 A
of the rate of item No. 012015 for 70% of the excavated quantity considering 30% as
backfill
(i) for thrust bed ( 34.80 X 7.60 X 8.00) =2115.84
(ii) For Box Portion ( 6.70 X6.35 X 35.30) = 1501.84
(iii) for approach formation ( 8.00 x20.00 x2.00) = 320.00
Total quantity of excavation = 3937.68 cum
Quantity taken for leading = 70% x 3937.68 cum = 2756.38
Dewatering of accumulated water from any location.Payment to be done for horse HP Hour 052260 40.58 150.00 6,087.62 A
power of pump multiplied by pumping hour 10 days x 3 hours per day x 5 hp =150 as
per item no. 052260
Providing and laying Cement Concrete 1:4:8 using 40 mm aggregate in base Cum 022036 2549.73 13.22 33,717.67 A
course below thrust bed 34.80 X 7.60 X 0.05 = 13.224 Cum as per item no. 022036
Providing 50 mm thick screed with CC 1:2:4 using 12.5 mm aggregate thrust bed Cum 022032 2520.20 13.22 33,327.15 A
34.80 X 7.60 X 0.05 = 13.224 as per item no.022032
Cutting edge total qty 12000 kg - 3.00MT for each box out of which 1500 kg will be MT 023030 122795.38 2.78 341,371.16 A
embeded in concrete and cannot be reused and balance 1500 kg wiil be useful as
scrap after pushing as per item no 023030.
- Salvage value of 50% of steel quantity i.e 3000/2 = 1500 kg.@15%
Net quantity = 1500 x 1.85 = 2775 kg = 2.775 MT Say 2.78 MT
Polyvinyl chloride sheet 400 micron. Sqm 0248 40.25 536.56 21,596.54
Supplying of polyvinyl chloride sheet 400 micron. Thrust bed area 35.3 X 7.6 X 2
times
Grease MP-2 or equivalent of HPCL/BPCL/IOCL Kg 0187 153.00 120.00 18,360.00
2062
(Pins and packings plate total qty 16000 Kgs this can be used for 10 box pushings
works Net qty for each box pushing = 16000/10 =1600 Kg- 16 Quintals)
Hire charges for 200 MT capacity Jack Day 0107 1500.00 735.00 1,102,500.00
(21 Jacks required per day X 35 Days at the rate of 1.0 m length of pushing per
day)
Hire charges for Power pack with 200 litres capacity tank with 10 HP 3 phase Day 0078 5265.00 35.00 184,275.00
induction mortar, inlet, out let valves pressure gauges, hose pipes etc for pushing
arrangement including consumables, tools, plants, operator, and transportation to
site of work
Hire charges for 3 phase generator (60 KVA) Day 0075 2000.00 35.00 70,000.00
Providing road crane ( hydra ) of 12 MT capacity for mobilization heavy machinery
like pins, packs and jacks etc
Hire charges of 12 MT Hydra Day 0090 5000.00 35 175,000.00
(P) Providing and removing barricading with the help of portable fencing with self Metre 013041 191.89 100.00 19,188.53 A
supporting steel angles of size 50 x50x6mm, 1.5m long provided with hooks etc.
and embedded in CCreflective tapes in Horizontal & vertical direction. Note :
Released material will be the property of the contractor after the completion of work.
Cost of cement to be paid separately as per item no 013041
Hire charges of 7.5 KVA Generator Day 0073 1000.00 35.00 35,000.00
Hire Charges of Halogen Lamps 500 Watt Nos. 0488 40.00 420.00 16,800.00
slewing of disturbed track to correct alignment , lifting /lowering of track under traffic
condition and maintenance of track to required standard during the entire period of
box pushing with all contractors tools and plants ( daily 6+1+1 labour for 35 days.
Labour shall work for track correction for half day and other works in remaining
period.
Labour:
Highly Skilled labour Day 0018 714.00 35.00 24,990.00
Mate (Skilled) Day 0002 609.00 18.00 10,962.00

Code (Rs.) (Rs.)
(N) Providing cast in situ bridge number plaques as per item 052210 Each 052210 735.60 2.00 1,471.20 A
(O) Providing cast in situ foundation plaques as per item 052220 Each 052220 1137.51 1.00 1,137.51 A
Sundries (no rates reqd.) incl conduits etc. Lumpsum 9901 1.00 15000.00 15,000.00
Sub total-1 3,037,750.69
Sub total-2: Sub-Total of items marked as (A) to (P) (USSOR items final Rates are 1,111,265.15
adopted)
Sub-Total-3: Total of item without water charges,GST, Contractor profit & 1,926,485.54
Overheads, Cess. = Cost at Sub-Total 1 (-) Cost at Sub-Total -2 of items marked as
(A) to (P)
1,945,750.40
2,219,128.33
2,551,997.57
Sub- Total-4: Total cost of items except (A) with water charges,GST, Contractor profit 2,577,517.55
& Overjheads, Cess
Sub Total-5: Total Cost without Design Charges. 3,688,782.70
Designing and drawing of RCC thrust bed, cutting edge and drag sheet 0.02 73,775.65
arrangement ( @ 2 % total cost )
Total Cost for 5.5 x 5.0 x ( 34.8+35.8)/2 size box (clear inner volume of 970.75 cum) 3,762,558.35
except cost of concrete, cement, reinforcement & shuttering of components of work
Specified above.
031121 Extra for using GI Drag Sheet for protection of track support from subsidence while
pushing the box as per design over item no. 031120.
Note:The payment for this item shall be made for the clear inner cross section area of
the parent RCC Box/Boxes and barrel length.
Material:
Drag sheets: 1.50 mm thick GI Sheet in ribbons of 50 cm width 36 x 6.7 = 241.2 Sq.M x
11.77 kg/sq.m=2840 kgs
GI Sheet 1.50 mm thick Quintal 0246 4600.00 28.39 130,594.00
Supporting frame and ancillary arrangement for fixing of drag sheet MT 023030 122795.38 5.74 704,845.50 A
Total qty 9000 kg - 9.00MT. After completing the work, 85% of structural steel shall
be salvaged and considering scrap value @ 25% of the original cost, quantity to be
charged for providing arrangement = 9000 x 0.85 x (1-0.25) = 5737.5 kg Say 5.74
MT. Rate of fabricated arrangement as per item no. 023030.
Total except "A" 130,594.00

131899.94
150431.88
172996.66
Sub-Total (excluding "A") 174,726.63
Total Cost for 5.5 x 5.0 x ( 34.8+35.8)/2 i.e. 970.75 Cum inner volume of RCC Box. 879,572.13


Code (Rs.) (Rs.)
031130 Casting and installation of single/twin RCC box of all sizes with or without common
web section after supporting the track on temporary girders including design of
pushing scheme, thrust bed, casting of all RCC components, with specified grade of
controlled concrete, pushing it in correct position and alignment below Railway
track/Road following all measures of track safety by “Air pushing technique" as per
approved drawings/scheme, in all types of soils with disposal of surplus earth away
from vent up to 1 Km, fixing arrangement for all services & utilities including parapet
walls on both sides, wearing course, foot paths, plaques, drainage arrangements etc.
and all other incidental works to complete the ROB/RUB/Canal crossing in all respect
as per specifications to the satisfaction of Engineer-in-Charge.
Note:
(1) The rate includes all items of work/supplies for complete job in all respects except
"cost of Reinforced cement concrete, cement, reinforcement & shuttering" of (i) main
RCC Box; (ii) Thrust Bed; (iii) Footpath and (v) wearing Course only, which shall be
paid extra under relevant items of USSOR.
(2) The CC Cribs as required and Temporary Girder shall be supplied by Railways.
(3) Transportation of Temporary Girder to the site shall be paid separately under
relevant item.
(4) The payment for this item shall be made for the clear inner cross section area of
the parent RCC Box/Boxes per unit barrel length i.e. clear inner volume of parent
RCC Box/Boxes.
Box Dimensions
Adopting appoved GAD Drg No GM/W/SC/BR/RUB/SC/3903/2018 dimensions
Clear span: 5.50M

Clear Height of the box: 5.0M
Wall thickness: 60 cm
Slab thickness: 60 cm
Barrel length of box: 16.85 M
Inside dimensions of box ( considering average thickness of wearing course) 5.5
X5.375 X 16.85 ( 16.85 is pushing length of box)
Out side dimenshions of box: 6.7 X6.575 X 16.85
Proposed Casting Bed Dimensions
Length of casting bed: 20.875 Mts
width of casting bed: 7.6 mts
Thickness of casting bed: 0.75 Mts
Excvation for for casting bed and approaches
(i) Earth work in excavation as per item no. 022011 for casting bed and at approaches Cum 022011 169.23 572.00 96,797.48 A
and disposal of surplus soil upto a lead of 2 km including loading, unloading and
pumping out of water if required
(casting bed 21 x 8 x 1.50 = 252.00 Cum ) + (Approaches 20.00 x 8.00 x 2.00 ) =
320.00 Cum. Total Quantity = 252.00 + 320.00 = 572.00 Cum.
Excavation in formation and insertion of Temporary girder , cribs and for air pushing
as per item no. 022011
(ii) Main Box Portion = 2500 Cum
All kinds of soils Cum 022011 169.23 2500.00 423,065.92 A
(B) Leading of excavated earth up to 1km i.e. average lead of 0.5 km. Cost as per Cum 012015 3.12 2150.40 6,713.24 A
50% of the rate of item No. 011015 for 70% of the excavated quantity considering
30% as backfill
(a) for thrust bed = 572.00
(b) For Box Portion = 2500
(c) for approach formation = 320.00
Total quantity of excavation = 3072.00 cum
Quantity taken for leading = 70% x 3072.00 cum = 2150.40
(C) Providing and laying Cement Concrete 1:4:8 using 40 mm aggregate in base Cum 022036 2549.73 7.93 20,219.38 A
course below thrust bed 20.875.00 X 7.60 X 0.05 = 7.933 Cum as per item no.
022036

Code (Rs.) (Rs.)
(D) Providing 50 mm thick screed with CC 1:2:4 using 12.5 mm aggregate thrust Cum 022032 2520.20 7.93 19,985.20 A
bed 20.875 X 7.60 X 0.05 = 7.933 as per item no.022032
Supply and filling sand in formation before pushing the boxes 10 x 17 x 0.20 = 34 Cum 052240 2105.56 34.00 71,589.11 A
cum
Insertion of temporary girder in place of formation as per item no. 191021.
RH /Temporary girder of length varying from 12.2m to 16.3m using road crane Each 191021 85581.12 1.00 85,581.12 A
capacity of 80 tons
Removal of temporary girder, crib on both ends and placing temporary girder on crib
/ cess away from Railway track as directed by engineer at site under traffic block;
filling of Railway's earth by ramming, pulling ballast from stack / adjoining track /
same track, laying track, linking with approach track and packing of ballast for
opening track at 20 kmph speed, boxing & dressing of cess, ballast profiling etc. as
per item no. 191041.
RH /Temporary girder of length varying from 12.2m to 16.3m using road crane Each 191041 91124.59 1.00 91,124.59
capacity of 80 tons
Note:- Excavated earth from Rly area will be used
Quantity of sleepers for 56 Sleepers= 56 x 2.74 x 0.20 x 0.15 = 4603 Cudm = 460.32
Manufacturing and using wooden sleepers/blocks required for matting and bearing as Cum 191030 936.56 4.60 4,310.97 A
per approved design for use below and above CC Crib for insertion of Temporary
Girder.
Note: The item is for one time use and released wooden sleepers/blocks shall be the
property of the Contractor.
Rolling of box
JACKS
Jacks ( One jack of 200 MT capacity is required for jacking of 100 MT weight of
box. Wieght per 1 mt length of 5.5 x 5.375 m box = 37.75 MT for 16.85 mt length
636 Mt +1/4 of 636 MT for friction total 795 MT ie 8 jacks + 2spare 10 jacks
required x (5+3) days for rolling 10 jacks per day x 8 days =80 jacks
Hire charges for 200 MT capacity Jack Day 0107 1500.00 80.00 120,000.00
Power pack: 2Nos x ( 5+3) days

Hire charges for Power pack with 200 litres capacity tank with 10 HP 3 phase Day 0078 5265.00 16.00 84,240.00
induction mortar, inlet, out let valves pressure gauges, hose pipes etc for pushing
arrangement including consumables, tools, plants, operator, and transportation to
site of work
Generator: During pushing period ie 5+3 days

Hire charges for 3 phase generator (60 KVA) Day 0075 2000.00 8.00 16,000.00
Extra Semi skilled labour (5 Nos x 7 days)
Providing road crane ( hydra ) of 12 MT capacity for mobilization heavy machinery Day 041201 8268.45 7.00 57,879.18 A
like jacks etc
Highly skilled labour for air pushing in correct line and level
Girder mainteance work
Skilled labour for girder maintenance 9 days x 2 N os per day
Mate (Skilled) Day 0002 609.00 18.00 10,962.00
skilled labour for girder maintenance 9 days x 4 Nos per day
Semi skilled labour for girder/track maintance 9 days x 5 N os per day
Electrician (Skilled) Day 0013 609.00 1.00 609.00
Hire Charges of Halogen Lamps 500 Watt Nos. 0488 40.00 96.00 3,840.00
Providing and removing barricading with the help of portable fencing with self Metre 013041 191.89 100.00 19,188.53 A
supporting steel angles of size 50 x50x6mm, 1.5m long provided with hooks etc.
and embedded in CC .With provision of painting verticals & horizontals with red
luminous paints / Strips of 30cm each with a gap of 30 cm.

Code (Rs.) (Rs.)
Cement (0.019 Qtl per metre) MT 025062 6689.69 1.90 12,710.41 A
Providing cast in situ bridge number plaques Each 052210 735.60 2.00 1,471.20 A
Providing cast in situ foundation plaques Each 052220 1137.51 2.00 2,275.03 A
Total of all items including marked "A" 1,225,658.36
Deduct Total of items Marked 'A' 869,833.54
Total of items excluding "A" 355,824.82
359,383.07
409,876.39
471,357.84
Total of items excluding "A", with Overheads 476,071.42
Grand total- of all items 1,345,904.96

Designing and drawing of RCC casting bed ( @ 2 % of sub total cost ) 0.02 26,918.10
for 5.5 m x 5.00 m x 16.85 m = 463.375 Cum 1,372,823.06
031140 Fabrication, insertion and removal of rail cluster below the running track to ensure
safety of track during box pushing in correct position and alignment with Railway rails
and contractors MS flats, wooden blocks, and 12 mm dia bolts etc., as per approved
drawing including removing and filling back of ballast below track under traffic
conditions of Electrified/Non-Electrified section with all contractors, labour, tools,
tackles, consumables plants, and 50MT capacity crane and any other material
required for execution of work in all respect with all lead and lift, transportation and as
directed by Engineer in-charge. Payment quantity shall be as per the weight of rail in
rail cluster used at site or as per approved drawing, whichever is minimum.
Note:
(i) Insulated Elastomeric pad (Railway supplied) shall be used between Running rails
and cross rails to prevent failure of track circuit.
(ii)CC Cribs will be supplied by the railways at free of cost, if they are required to be
inserted under the track.
Transportation to the site and back to the required location will be paid by Railways
under relevant agreement item
(iii)Rail cluster should be properly maintained by proper packing under wooden blocks
/mattings during passage of trains and de assemble after completion of work
Fabrication of 9 rail cluster of 13.0 mt long by

providing clamping arrangemebt with MS flats (2Nos)
Removing and refiiling ballast from below the trcak for insertion/removal of rail cluster

Supply of MS flats of 50 x 8 ( 1.2 x 8 Nos x 3.097 kg/mt=29.730 kg.
M S Flat upto 10 mm thickness Quintal 0230 6300.00 0.30 1,890.00
Supply of wooden mats ( 1.5 x.15 x1.2 x 4 Nos
+Add sleepers 1.5 x .45 x1.2 x 4 Nos = 4.32 Cum or 4320 cudm)
Considering reuse for the 5 times, quantity to be taken for once = 4320/5 = 864 cudm
Hard Variety Jungle Wood blocks 10 Cudm 0343 350.00 86.40 30,240.00
Supply of 12 mm dia screws ( .35 length 16 Nos )
Nut & Bolts with washers of all sizes Kg 0234 80.00 0.96 76.48
Providing road crane of 50 MT capacity for Day 041203 27561.52 3.00 82,684.55
insetion /removal of rail cluster and handling of rails
Handling of rails during insertion /removal and De assemblibg rail cluster
Sub-Total Including 'A' 137,534.03

Code (Rs.) (Rs.)
Sub-Total excluding 'A' 54,849.48
55,397.97
63,181.39
72,658.60
Grand total- 73,385.18
Grand Total including 'A' 156,069.73
Total cost for Fabrication, insertion and removal of rail cluster below running the track
for single track (Weight 19.71 MT)
Rate per 1 MT MT 7,918.30
031150 Launching of precast RCC box segments for RUBs/Limited Height Subways (LHS) of
any size and barrel length for single/double line as per approved drawings to the
correct alignment and position in electrified / non-electrified sections safeguarding all
utilities ( S&T cable, power cable, OHE, pipelines etc.) including transportation of box
segments from casting yard to site of launching, dismantling of the existing track,
removing & stacking of ballast, cutting of formation and approach road below or
above bed level, placing of base slabs & Box segments in position, backfilling after
launching of precast box segment, ballasting & re-laying of track to correct alignment
and geometry, packing and further maintenance till allowing non-stop 20 KMPH over
the re-laid track, complete in all respect to the satisfaction of Engineer-in-charge. The
rate is all inclusive except the cost of RCC Box Segments, Base Slabs and backfill
material which shall either be supplied by railway or paid extra under relevant item.
Note: Minimum equipment required during block shall be (i) Crawler mounted
Hydraulic excavator of min 200 HP and bucket capacity 2.5 cum - 3 numbers and (ii)
3 cranes of adequate boom length suitable for launching box segments in position
(min capacity of each crane - 200 MT for Single Line and 300 MT for Double Line)
apart from other equipments, tools, plants and machinery required to complete the job
within the allowed block period.
031151 For Single Line

Quantity taken for analysis is for Single Line
Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
Electrician (Skilled) Day 0013 609.00 2.00 1,218.00
Machinery:
For calculation of hire charges of 200 MT Capacity Cranes and 200 HP Hydraulic
Excavator, 1 day for travel (to & fro) with charges as half of working hire charges,
equvalent days shall increase by 50%. Therefore insted of 3 cranes and 3 Hydraulic
Excavator for one day of working, it will be taken as 4.5 crane-days and 4.5
excavator days for calculation purpose..
/ hammers
Hiring of Trailor truck of 20 MT capacity Day 0102 18000.00 1.00 18,000.00
Hire Charges of Halogen Lamps 500 Watt Nos. 0488 40.00 12.00 480.00
921,518.00
930,733.18
1,061,501.19

Code (Rs.) (Rs.)
1,220,726.37
Rate for Single line Each 1,232,933.63
031152 For Double Line

Quantity for double line
Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
Electrician (Skilled) Day 0013 609.00 2.00 1,218.00
Machinery:
Hire Charges of 300MT Capacity Cranes 3 Nos. during block (2 working and 1
standby). Considering 1 day for travel (to & fro) with half the charges of working,
Crane days required = 3 x 1.5 = 4.5 crane-days.
Hiring charges of 300 MT capacity crane Day 0100 250000.00 4.50 1,125,000.00
Hiring of Trailor truck of 20 MT capacity Day 0102 18000.00 1.00 18,000.00
/ hammers
1,293,276.00
1,306,208.76
1,489,731.09
1,713,190.75
Rate for Double line Each 1,730,322.66
031160 Loading, tranportation of Precast RCC Girders / Slabs / Ballast retainers / Steel
Girders etc. from Casting Yard to Site of Work, unloading and stacking at site of work
at prescibed location as directed by Engineer-in-Charge.
Rate directly connected to Working Sheet for calculation of transportation charges
031161 Upto 5.00 Km MT 141.33 1.00 141.33

031162 Above 5 km upto 10 km MT 191.01 1.00 191.01
031171 Beyond 80 km MT KM 7.49

Code (Rs.) (Rs.)
031180 Providing Flood Level Gauges on abutments and piers, made by 20mm thick 1:4
cement plaster for a width of not less than 300mm, duly engraving markings & figures
in metres, divided into 10 parts commencing from under-side of girders towards bed,
painting markings & figures with black enamel paint in three coats on white
background including painting HFL Mark in white by side of gauge with year of
occurence with all Contractor's materials, labour, tools, scaffolding and supports,
lead & lifts, curing etc. complete as per approved drawing and as directed by the
Engineer in- charge excluding cost of cement which shall be paid extra.
Details of cost for 100 Sqm

Details of cost for 1 cum Cement Mortar
20mm thick Cement plaster (1:4) as per following item
Material:
(0.268 cum of cement = 0.38 tonne)
Labour:
For measuring,carrying,depositing and mixing
Hire and running charges of mechanical mixer Lumpsum 9901 1.00 30.00 30.00
Cost of 1 cum Cum 1,686.12
a) Details of cost for 10 sqm 20mm thick 1:4 Plaster

Materials:
Cost of 1 cum 1:4 Cement Mortar Cum 1686.12 0.22 377.69
Labour:
Scaffolding and sundries Lumpsum 9901 1.00 10.00 10.00
1,857.51
1,876.09
2,139.68
2,460.63
Cost of 10 sqm 2,485.23
Cost of 1 sqm Sqm 248.52
b) Painting two coats (excluding priming coat) with chocolate, red, grey or buff ready
mixed paint of approved quality on steel or wood work
Details of cost for 10 sqm
Materials -
Synthetic Enamel Paint in Black or Chocolate shade Litre 0310 220.00 1.16 255.20
Material for filling in hole and cracks Lumpsum 9901 1.00 5.00 5.00
Labour:
Putty ,Brushes ,sand papers etc. Lumpsum 9901 1.00 10.00 10.00
841.80
850.22
969.67
1,115.12

Code (Rs.) (Rs.)
Cost of 10.00 sqm 1,126.28
Cost of 1.00 sqm Sqm 112.63
c) Lettering with “Synthetic Enamel” paint (two coats) of approved brand and
manufacture
Details of cost for 100 letters of 15 cm height
Materials -
Enamel Paint as per RDSO's Spec. no.M&C/PCN/120-2011 Litre 0306 190.00 0.56 106.40
Labour-
Painter (Skilled) Day 0012 609.00 6.00 3,654.00
Painting brushes,turpentine stencil etc. Lumpsum 9901 1.00 20.00 20.00
4,652.40
4,698.92
5,359.12
6,162.99
Cost of 100 letters of 15 cm height 6,224.62
Cost of 1.00 letter of 1 cm height Each 4.15
Total cost for 100 Sqm
20mm thick Cement Plaster (1:4) as per (a) above. Sqm 248.52 100.00 24,852.34
Painting with synthetic enamel as per (b) above. Sqm 112.63 100.00 11,262.76
Lettering with “Synthetic Enamel” paint as per (c) above. Each 4.15 3000.00 12,449.24
Cost for 100 Sqm 48,564.34
031190 Providing and fixing in position GI Drainage Spouts of required length with Grating in
RCC slab and filling bitumen along kerb as shown in drawing with contractor's pipes,
bitumen, tools, equipment, lead, lifts etc. complete as per specifications and as
directed by Engineer in-charge.
031191 50mm dia. Drainage Spouts

Details of cost for 10 x 10m = 100m pipe
Material:
GI Pipe 50 mm dia , B Class Medium duty Metre 0262 315.35 105.00 33,111.75
Bitumen Hot sealing compound : Gr. A MT 0319 28000.00 0.01 280.00
Clamps and MS stays including bolts and nuts for 50mm dia pipe Each 0265 53.00 50.00 2,650.00
C I grating 100mm x 100mm Each 0266 75.00 10.00 750.00
Labour:
Mason 2nd class (Semi-skilled) Day 0005 505.00 2.00 1,010.00
39,625.75
40,022.01
45,645.10
52,491.86
Cost for 100 Metre Pipe 53,016.78
031192 100mm dia. Drainage Spouts

Details of cost for 10 x 10m = 100m pipe
Material:
Bitumen Hot sealing compound : Gr. A MT 0319 28000.00 0.02 420.00

Code (Rs.) (Rs.)
Clamps and MS stays including bolts and nuts for 100mm dia pipe Each 0264 90.00 50.00 4,500.00
C I grating 100mm x 100mm Each 0266 75.00 10.00 750.00
Labour:
85,316.75
86,169.92
98,276.79
113,018.31
Cost for 100 Metre Pipe 114,148.49
031200 Applying Epoxy Poly-sulphate Paint three coats on existing bottom surface of deck
slab including cleaning surface of dirt, dust & other foreign matter, sand papering,
wire brushing as required with all contractor’s materials tools, machinery, scaffolding,
lead, lifts etc. complete as per specifications and as directed by Engineer in-charge
Detail of cost for 10 Sqm

Material:
Epoxy paint as per RDSO Spec M&C/PCN/123-11 Litre 0311 440.00 3.00 1,320.00
Soft Brush for painting - 25cm long Each 0314 33.00 1.00 33.00
Labour:
2,393.00
2,416.93
2,756.51
3,169.98
Cost of 10 Sqm 3,201.68
031210 Supplying and laying 160mm dia. PVC Pipes Class-I, capable for a pressure of 2.5
kg/sqm in footpath of ROB for laying cable with all contractor’s materials labour, tools,
plant, machinery, vehicles, consumables, lead, lift etc. complete as per specifications
and as directed by Engineer in-charge.
Detail of cost for 10m pipe

Material:
uPVC Pipe- type A ISI marked 160mm dia Metre 0261 350.00 10.00 3,500.00
Labour:
3,917.75
3,956.93
4,512.88
5,189.81
Cost of 10 Metre pipe 5,241.71
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 4: Bridge Work (SuperStructure-Steel)
CHAPTER - 4 : Bridge Works : Super Structure- Steel

Code (Rs.) (Rs.)
041010 Supplying, fabrication, assembling of all types of steel girders of specified spans with
structural steel conforming to Quality "B0" Grade Designation E250 conforming to
IS:2062, erection / slewing / end launching of steel girders with cranes or any other
approved launching methods as per site conditions (not requiring traffic block) on sub-
structure including provision of trolley refuges etc., complete as per approved QAP
and drawings conforming to IRS-B1-2001 and other relevant codes and specifications.
Note:
1. Detailed fabrication and erection drawings & launching methodology will be prepared
by the contractor and got approved from Railway.
2. The rate is all inclusive including launching in position, complete in all respect except
cost of (i) Painting other than primer coat; (ii) Bearings & (iii) HSFG bolts which shall be
paid extra under relevant item.
3. The payment shall be made on the theoretical weight of main components and
gusset plates only.
4. Payment Schedule:
(i) Receipt of material at site: 40%
(ii) Fabrication of girders: 20%
(iii) Erection/Launching: 20%
(iv) Completion in all respects: 20%
041011 Plate Girder/Semi Through Girder/Composite Girder (Steel Work)

Basic cost for fabrication, errection, leading , painting primer coats.and final two coats
of paint at site.
Take a Plate girder of 12.20 m length 25T Loading standard weighing 14.69 Tonnes
i.e. 146.90 quintal
(A) Material:
(a) Structural Steel i.e Plates & Angles
(i) Plate = 140.57 quintal + wastage @5% = 147.60 quintals
(ii) Angles = 6.33 quintal + wastage @ 5% = 6.65 quintals
Structural steel plates conforming to Grade Designation E250; Quality "B0" as per Quintal 0225 7330.00 147.60 1,081,908.00
IS:2062,
(B) Cutting:
(i) Plates
Cutting length : 243.748 m (All Thicknesses)
Gas Required for Cutting
DA Gas in cylinder @ 1 Cylinder of 19 Kg per 26m length of Cutting
Acetylene Gas (in cylinder) Kg 0341 65.00 178.12 11,578.03
Oxygen Cylinder @ 7 Cylinders ( 7 Cum) per 26m length of Cutting (Density of Gas
1.429 Kg/M3. Qnty of Gas in Kgs = 243.748/26*7*7*1.429 =656.44 Kg)
Oxygen Gas (in cylinder) Kg 0340 50.00 656.44 32,822.07
Hire Charges of CNC Gas Cutting machine @ 0.400m/1min = 243.748/0.40/60 = 10.15
Hours Say12 Hours
Hire Charges of CNC gas cutting Machine Day 0115 4500.00 1.50 6,750.00
Labour Skilled (For Steel Fabrication i.e. Machine Operator/Welder/Machinist etc.) Day 0019 609.00 1.50 913.50
(ii) Angles
Total Number of Cuts = 120
Hack Saw Blades Each 0458 593.22 2.00 1,186.44
Time required @ 1 Cut in 5 minutes
Labour Skilled (For Steel Fabrication i.e. Machine Operator/Welder/Machinist etc.) Day 0019 609.00 2.00 1,218.00
Labour Unskilled Day 0020 431.00 2.00 862.00
Edge finishing by Grinding
Total length for finishing = 2,43,748 mm i.e 243.748m
Grinding of 12 meters requires 20 min
Time required @ 12m in 20 minutes = 243.748/12*20/60 = 6.77 Hours
Cup Grinding Stone Each 0236 900.00 1.00 900.00

Code (Rs.) (Rs.)
Edge Preparation for Welding
Length of the Edge for welding 106.40m
Time required for edge preparation = 106.40 * 15/12 = 2.15 Hours
Jig and Fixtures
Material Required for Jig 0.302 MT. Considering that the Jigs shall be used 5 times and
the salvage value of plate is 30%. The amount of steel to be charged for 1 girder =
0.302/5x0.7 =0.042 MT = 0.42 Quintal.
Cost of Fabrication of Jig and Fixtures considering cost equivalent to the material
required for Jig
Drilling of Holes
Total Number of Holes to be drilled = 498
Drill Bit @ 1000 holes / Bit
Drill Bit Each 0237 300.00 2.00 600.00
Time required for drilling 498 holes @ 4 holes / 4 minutes with CNC drilling Machine i.e
1 minute / 1 Hole = 498 /60 = 8.15 Hours Say 1.5 Days
Hire Charges of CNC drilling machine - 14 to 50mm dia, 100mm thickness, set of Day 0116 14000.00 1.50 21,000.00
spindle - 2 sets, accuracy +/- 0.03mm.
( C ) I-Section Assembly
(i) Tack Welding:
Tack Welding to be done = 17733 mm of 5mm fillet
Volumeof material for welding = 1/2*5*5*17733 = 221662.5 mm3
Length of 5mm dia Electrode required = 221662.5 / (3.14*5*5/4) = 11294.90 mm.
Electrodes for steel fabrication work Metre 0238 24.00 11.29 271.06
A Welder can do 3 to 3.5m length of FCAW/GMAW mig welding per hour
No of Welders required = 17.733/3.5 = 5 Hours
Hire Charges of MMAW machine ( Manual Metal Arc Welding Machine) - 80 to 500 Day 0117 25.00 1.00 25.00
Amperes.
(ii) SAW Welding
SAW total length = 13300*4*2= 106400 mm of 12mm fillet weld
Volume of Wire required = 1/2*12*12*13300*4*2 = 7660800 mm3
Weight of Wire required = 76,60,800 / 109*7850 = 60.137 Kg
SAW Welding Wire Kg 0240 66.00 60.00 3,960.00
Flux used =1/3 rd of weight of wire = 20 kg
Flux for SAW Weldging Kg 0241 65.00 20.00 1,300.00
Root welding in SAW .e 5mm Weld Size for 12m, will take 20-30 Minutes
Root Run for 12 mtrs in 30minutes = 106.4*30/12/60 = 4.5 Hours
Highly Skilled labour Day 0018 714.00 0.50 357.00
Final Run @ 12 mts run in 45 minutes for 106.4 m = 106.4*45/1/60=6.65 Hrs
Highly Skilled labour Day 0018 714.00 1.00 714.00
Hire Charges of SAW machine - Tornado Make, current range - 150 to 1250 Amperes. Day 0118 7500.00 1.50 11,250.00
(iii) CNC End Grinding to achieve final Tolerances of I-Section

Hire Charges of Angle grinder - 230mm dia. Disc, 6000 rpm, CP make. Day 0119 11.00 1.50 16.50
(iv) HSFG Bolts tightening to fix Stiffener Angles

Code (Rs.) (Rs.)
Stiffener HSFG Bolting = 522 Nos
5 Persons can fix 250 Bolts in 1 day
Hire Charges of Impact wrench - 32mm dia.Boit, CP Make. Day 0120 25.00 5.50 137.50
Hire Charges of Torque wrench - 150 kgf-m, Mekaster Make. Day 0121 10.00 5.50 55.00
Hire Charges of Power hack saw machine (Angle) Day 0122 25.00 1.50 37.50
Hire Charges of CNC end milling machine - (Horizonral Spindle), (1). Longitudinal Day 0123 17000.00 2.00 34,000.00
Traverse of table (X-Axis) - 1500mm (2). Vertical Axis (Y-Axis) - 1000mm, (3).RAM
Column Traverses (Z-Axis) - 500mm.
(v) X-Frame Assembly

4 people for one X frame - 2 to 3 Hours say 1/2 day
For 4 Frames, 4*4*1/2 =8 Mandays
(D) Final Assembly of Girder & Inspection
(E) Sand Blasting as per item Annexure - X (i) of Item No. 041040 MT 041040 1388.25 10.37 14,396.15
(F) Hire Charges of EOT Crane Day 0124 1500.00 17.00 25,500.00
For 12.2 m Plate Girder, Cost of Electric consumption @ 100 Units / MT = 100 *10.327
=1032.7KWH. \
Electricity Charges ( 1 Unit ) KWH 0505 7.50 1032.70 7,745.25
Total 1,321,639.50
1,334,855.90
1,522,403.15
1,750,763.62
Cost for 14.69 MT 1,768,271.26
Cost for 1.00 MT 120,372.45
Cost for Launching Same as per item no. 041031 MT 041031 12460.72 1.00 12,460.72
041012 Open web Girder

Basic cost for fabrication, errection, leading , painting primer coats.and final two coats
of paint at site. For cost calculation, span of 45.7m has been taken.
Take a Open Web Girder of 45.70 m Span 25T Loading standard weighing 137.927
Tonnes weight
(A) Materials : Structural Steel
(a) Structural Steel i.e Plates & Angles
(i) Plate = 1297.41 quintal + wastage @5% = 1362.28 quintals
(ii) Angles = 81.86 quintal + wastage @ 5% = 85.96 quintals
Structural steel plates conforming to Grade Designation E250; Quality "B0" as per Quintal 0225 7330.00 1362.28 9,985,512.40
IS:2062,
(B) Cutting:
(i) Plates
Cutting Area : 205.926 sqm
Gas Required for Cutting
DA cylinder @ 19 Kg per 0.65 sqm = 205.926/0.65x19 = 6019.38 kg
Oxygen Cylinder @ 7 Cylinders ( 10 kg/7 cum) Qnty of Gas in Kgs =
205.926/0.65x10x7 =22176.65 kg (15,518.99 cum)
Oxygen Gas (in cylinder) Kg 0340 50.00 22176.65 1,108,832.50

Code (Rs.) (Rs.)
Hire Charges of CNC Gas Cutting machine @ 0.400m/1min = 8237/0.40/60 = 10.15 Day 0115 4500.00 21.00 94,500.00
Hours Say12 Hours
(ii) Angles
Total Number of Cuts = 490 nos.
cost of blades @ 60 cuts per Blade
Hack Saw Blades Each 0458 593.22 9.00 5,338.98
Time required @ 1 Cut in 5 minutes, 490*5/60=40.83 = 5.1 days Say 5 days
Edge finishing by Grinding
Total length for finishing = 38,46,544 mm i.e 3846.544 m
Grinding of 12 meters requires 15 min
Time required @ 12m in 20 minutes = 3846.544/12*15/60 = 80.14 Hours
=10.01 days Say 10 days
Cost of Cup Grinding Stones @ 1 Stone per 250m=3846.544/250=15.39 Say 16
Cup Grinding Stone Each 0236 900.00 16.00 14,400.00

Jig and Fixtures
Material Required for Jig 2.123 mt. Considering that the Jigs shall be used 5 times and
the salvage value of plate is 30%. The amount of steel to be charged for 1 girder =
2.123/5x0.7 = 0.297 MT = 2.97 Quintal
2062
Cost of Fabrication of Jig and Fixtures considering equal cost of material 18,711.00
Drilling of Holes
Total Number of Holes to be drilled = 4500x2.5=11250
Cost of Drill Bit @ 1000 holes / Bit
Drill Bit Each 0237 300.00 12.00 3,600.00
Time required for drilling 11250 holes @ 4 holes of 21.5mm dia / 4 minutes with CNC
drilling Machine i.e 1 minute / 1 Hole = 11250 /60 = 187.50 Hours = 23.438 Day Say 24
Days
Hire Charges of CNC gas cutting Machine Day 0115 4500.00 23.44 105,468.75
( C ) I Section Assembly
(i) Tack Welding:
Tack Welding to be done = 24779 Nos of 5mm fillet @ 1 Tack of 50mm
@150mm=24779x5=1238950mm=1238.950m
Volumeof material for welding = 1/2*5*5*1238950 = 15486875 mm3
Length of 5mm dia Electrode required = 15486875 / (3.14*5*5/4) = 789140.127 mm
Electrodes for steel fabrication work Metre 0238 24.00 789.14 18,939.36
A Welder can do 3m length of FCAW/GMAW mig welding per hour
No of Welders required = 1238.95/3.0 = 412.98 Hours i.e. 51.62 Days say52 Days
Hire Charges of MMAW machine ( Manual Metal Arc Welding Machine) - 80 to 500 Day 0117 25.00 45.00 1,125.00
Amperes.
(ii) SAW Welding
SAW total length = 3716908 mm of 6mm fillet weld
Volume of Wire required = 1/2*6*6*37,16,908 = 6,69,04,344 mm3
Weight of Wire required = 6,69,04,344 / 109*7850 = 525.199 Kg Say 525
SAW Welding Wire Kg 0240 66.00 525.00 34,650.00
Flux used =1/3 rd of weight of wire = 575/3 = 175 kg

Code (Rs.) (Rs.)
Flux for SAW Weldging Kg 0241 65.00 175.00 11,375.00
Root welding in SAW .e 6mm Weld Size for 12m, will take 20-30 Minutes
Root Run for 12 mtrs in 30minutes = 3716.908*30/12/60 = 19.35 Hours Say 20 days

Hire Charges of SAW machine - Tornado Make, current range - 150 to 1250 Amperes. Day 0118 7500.00 20.00 150,000.00
(iii) GMAW Welding

GMAW total Length = 7,84,810mm = 784.810 m
Volume of Wire required = 1/2*6*6*784810= 14126580 mm3
Weight of Wire required = 14126580/ 109*7850 = 110.893 Kg Say 111
Welding Rod for Gas Metal Arc Welding Kg 0239 116.82 110.89 12,954.52
Shieding Gas (Co2) required = 1 Cylinder (22.50 Kg) @ Rs 29/-per Kg for 27 Meters.
Gas Required = 784.81/27*22.5=654.01 Kg
Shielding Gas (Co2) for fabrication works Kg 0244 69.00 654.01 45,126.58
A Welder can do 3 - 3.5m length of GMAW welding per hour
@3.5m/Hour, No of Hours = 784.810/3.5 = 224.231 hrs = 28.09.days Say 29 Days

(iii) End Grinding to match tolerences to be done for 76 members
@ 2 persons do 2 members per day ie 76/2 = 38 Days
Cost of Grinding Stones @ 1 Stone per 10 Components i.e 76/10 =7.6 Say 8
Cup Grinding Stone Each 0236 900.00 8.00 7,200.00
Hire Charges of Angle grinder - 230mm dia. Disc, 6000 rpm, CP make. Day 0119 11.00 38.00 418.00
(D) Trial Assembly of Girder & Inspection; 1 span will take 25 days for assembly
and 5 days for dismantling i.e total 30 days
Cost of Service Bolts for assembling of Girders Each 0243 35.00 1800.00 63,000.00

Sand Blasting as per item Annexure - X(ii) of Item No. 041040 MT 041040 3239.25 137.93 446,780.03
Hire Charges of Impact wrench - 32mm dia.Boit, CP Make. Day 0120 25.00 30.00 750.00
Hire Charges of Torque wrench - 150 kgf-m, Mekaster Make. Day 0121 10.00 30.00 300.00
Hire Charges of Power hack saw machine (Angle) Day 0122 25.00 6.00 150.00
Hire Charges of EOT, 10 ton Capacity, Reva Make Day 0124 1500.00 45.00 67,500.00
Hire Charges of Air compressor 500 Cfm for fabrication works Day 0066 1700.00 11.00 18,700.00
Cost of Drifts Each 0242 65.00 450.00 29,250.00
For 45.7m span Open Web Girder, Cost of Electric consumption @ 100 Units / MT =
100 x 137.927 =13792.7 KWH.

13,715,935.57
13,853,094.93
Add for GST @ 12% (multiplying factor 0.1405) Lumpsum 9903 0.14 1,946,359.84
15,799,454.76
Add for Contractor’s Overheads and Profit @ 15% Lumpsum 9904 0.15 2,369,918.21
18,169,372.98
18,351,066.71
Cost for 137.927 MT 18,351,066.71
Cost for 1.00 MT for Fabrication 133,049.13

Code (Rs.) (Rs.)
Cost for Launching Same as per item no. 041032 MT 041032 18654.43 1.00 18,654.43
041013 Extra for using steel conforming to Grade Designation E350 instead of Grade
Designation E250 of Quality "B0" as per IS: 2062
Structural Steel such as T, Angles, Channels and R S Joists Grade Designation Quintal 0229 6000.00 1.00 6,000.00
E350; Quality 'B0' as per IS 2062
Rate Difference 270.00
272.70
311.01
357.67
Rate for 1 Quintal 361.24
041014 Deduct for using steel conforming to Quality "BR" instead of Quality "B0" of Grade
designation E250 as per IS:2062.
Designation E250; Quality "BR" as per IS:2062,
Rate Difference -230.00
Sub Total -230.00
-232.30
-264.94
-304.68
Rate for 1 Quintal -307.73
Rate per MT MT -3,077.26
041015 Extra for using steel conforming to Quality "C" Grade Designation E250 instead of
Quality "B0" Grade Designation E250 of as per IS: 2062
tructural steel such as T, Angles, Channels and R S Joists conforming to Grade Quintal 0227 5860.00 1.00 5,860.00
Designation E 250; Quality "C" as per IS 2062
Rate Difference 130.00
Sub Total 130.00
131.30
149.75
172.21
Rate for Qtl Qtl 173.93
041020 Supplying and fixing HSFG bolts of any dia and any length with suitable nuts including
DTI washers conforming to IRS-B1-2001 for bridges and steel structures with
contractors labour, tools and plants and lead and lift etc., complete.
Consider 50 kg of bolts and washer


Code (Rs.) (Rs.)
Material:
HSFG bolt with DTI Wasters conforming to IRS B1-2001 with latest Correction Slips Kg 0231 100.00 50.00 5,000.00

Code (Rs.) (Rs.)
Labour:
5,620.00
5,676.20
6,473.71
7,444.76
Cost of 50 Kgs 7,519.21
041030 Assembling and erection of fabricated Steel girders on bearings at site with
crane/derrick / any other approved means at site on sub structure with labour,
equipment, T&P including site bolting with all temporary arrangements, scaffolding etc.
with contractors design and scheme for longitudinal launching/side slewing (not
requiring traffic block) approved by Railway. Rate includes drifts, service bolts, Holding
down bolts etc. as per drawings.
Note: Payment for HSFG bolts used if any will be made separately under relevant item.
041031 Plate Girder/Semi Through Girder /Composite Girder more than 12.2 m span
Take a Plate girder of 24.4m of MBG Loading standard weighing 443 Qtl weight
Material:
Holding down HTS bolts with plates, nuts etc. Quintal 0235 7500.00 0.25 1,875.00
20 mm dia holding down bolts 16nos.x460 mm 1840 mm Add wastage @ 5%
Total = 7.728 m @ 2.74kg/m = 21.17 kg = 0..21 quintal say 0.25 Qtls with nuts etc.
Labour:
Labour for errecton or launching
Machinery:
Hiring charges of Crane 20 MT capacity Day 0092 8000.00 10.00 80,000.00
Hire charges of air compressor 250 cfm capacity with two leads for pneumatic cutters / Day 0065 1600.00 5.00 8,000.00
hammers
Hire charges of Camber Jacks etc. Day 0108 500.00 30.00 15,000.00
145,875.00
Sudries, adhesives misc. T & P and consumables Lumpsum 9901 1.00 2000.00 2,000.00
147,875.00
149,353.75
170,337.95
195,888.64
cost of 443 Qtls. 197,847.53
Cost of Staging as per item no. 031070 for 24.40m 031070 354162.37 1.00 354,162.37
Total cost for 443 qtl 552,009.90
Rate Per Qtl. Quintal 1,246.07
041032 Open web Girder

For analysis purpose, take a Open web Girder of 45.7m and 1379.27 Qtl weight
Material:

Code (Rs.) (Rs.)
36 mm dia holding down bolts 24nos.x920 mm = 22080 mm Add wastage @ 5%
Total = 23.184 metres @8.604kg/m = 199.48kg = 1.995 quintal say 2.0 Qtls with nuts
etc
Labour:
Labour for errecton or launching
Bandhani (Semi skilled) Day 0022 505.00 60.00 30,300.00
Machinery:
hammers
Hire charges of Camber Jacks etc. Day 0108 500.00 240.00 120,000.00
Single coil spring washer for bridge bearing for 36 mm dia bolts Each 0297 12.00 48.00 576.00
1,389,156.00
Sudries, adhesives misc. T & P and consumables Lumpsum 9901 1.00 4500.00 4,500.00
1,393,656.00
1,407,592.56
1,605,359.31
1,846,163.21
Cost of 1379.27 Qtl 1,864,624.84
Cost of Staging as per item no. 031070 considering double of the cost of staging for 031070 354162.37 2.00 708,324.75
24.40m
Total cost for 1379.27 qtl 2,572,949.59
Cost for 1 quintal 1,865.44
041040 Metalizing of steel work of girders with sprayed aluminium after surface preparation by
Sand/grit blasting, followed by one coat of etch primer (IS:5666) & one coat of Zinc
Chrome primer (IS:104) and two coats of aluminium paint (IS:2339) with all labour, T&P
and material as a complete job duly conforming to all relevant specifications and
process given under Clause 39 of IRS-B1-2001.
Note: Nominal Thickness of Aluminium coating shall be 150 microns. DFT of Zinc
chrome primer shall be 25-30 microns and DFT of each coat of Aluminium paint shall
be 12-14 microns.
041041 On new girder during fabrication

Qty taken 10 Sqm
Meatallising on the steel-
Material:
Etch primer as per IS: 5666 Litre 0267 340.00 0.84 285.60
Ready mix Zinc Chromate primer as per IS 104 Litre 0307 100.00 0.90 90.00
Aluminium paint Litre 0309 160.00 1.80 288.00
Cost of Metalizing for 10 sqm as per Annexure - X below 10 Sqm 3,154.93
Labour:
Labour for application of paints after aluminium metalizing.
4,592.33
4,638.26
5,289.93

Code (Rs.) (Rs.)
6,083.42
Cost of 10.00 sqm 6,144.25
Rate for 1.0 sqm Sqm 614.43
041042 For maintenance work under running traffic

Considering additional cost over item 041041 for working under running traffic
Rate as per item no. 041041 614.43
Add for working under running traffic 0.25 153.61
Rate per sqm Sqm 768.03
Annexure - X for use in Item No. 041040

Metalization with spayed Aluminum for bridge girders as per IRS-B1-2001 with latest
Correction Slip after thorough cleaning of surface and roughened by compressed air
blasting with suitable abrasive material sand/grit as per site conditions and sparying
molten aluminium metal with specialized gun to get nominal thickness of 150 microns.
The purity of aluminium wire shall be 99.5% confirming to IS :2590.
Material:
(Consumption at the rate of 50sqm/cum; total quantity required-2.0cum)
Hire charges of air compressor 250 cfm capacity with two leads for pneumatic cutters / Day 0065 1600.00 0.20 320.00
hammers
Hire changes for sand receiver and sand blasting pipes with gun and all accessories Day 0130 500.00 0.20 100.00
complete
Hire charges for metalising gun with all accessories Day 0131 600.00 0.20 120.00
Aluminium wire for spraying Kg 0268 219.93 5.06 1,112.85
150 microns thick(The quantiy required for 10sqm is-10x0.00015X2700=4.05kg + 25%
wastage = 5.06 Kg
Oxygen Gas (in cylinder) Kg 0340 50.00 9.00 450.00
Commercial LPG (in cylinder) Kg 0339 73.71 1.60 117.94
Labour:
labour inculding sand blasting or grit blasting and application of sprayed molten
aluminium
Machine Operator (Machine) (Skilled) Day 0041 609.00 0.35 213.15
Add extra for grit blasting Lumpsum 9901 1.00 50.00 50.00
Cost of labour and material for 10 sqm 10 Sqm 3,154.93
Cost of only Sand Blasting for 10 Sqm 10 sqm 925.50
(i) Cost of only Sand Blasting Considering 15 Sqm/MT for Plate Girder 12.2 m Span MT 1,388.25
(ii) Cost of only Sand Blasting Considering 35 Sqm/MT for Open Web Girder 45.70 m MT 3,239.25
Span
041050 Providing and fixing railing used in rows for footpath or anti-crash barrier railing with B
class G.I. pipe 65/50 mm nominal dia including cost of M.S. angle and channels in
vertical posts, welding / bolting, priming painting with one coat ready mix Zinc
Chromate conforming to IS:104 with DFT of 25-30Microns, followed by one coat of Zinc
Chrome red oxide conforming to IS:2074 with DFT of 25 Microns with all material,
labour, T&P as a complete job.
Note: Cost of painting shall be paid extra under relevant item.
Taking output = 2 x 50 m span = 100 m

Total wt=2806+2142+180+150=5052Kg
Material:
(ISMC 100 = 2.806 x 1.05 = 2.946 MT)
Weight of ISMC 100 = 9.2 Kg/m For 294.6
(GI pipe medium grade = 400 X 5.10 x 1.05 = 2.142 MT=400X1.05=420)

Code (Rs.) (Rs.)
(MS bars = 0.17 x 1.05 = 0.180 MT)
MS bolts & nuts more than 10 mm dia Quintal 0252 8500.00 1.50 12,750.00
Labour:
Sundries including misc tools and plants Lumpsum 9901 1.00 1500.00 1,500.00
332,743.85
336,071.29
383,289.30
440,782.70
Total for 5052 kgs. 445,190.53
Rate per Kg. Kg 88.12
041060 Supplying and fixing M.S. Angles 65mmx 65mmx 8mm or any other size conforming to
IS:2062 in the nosing of steps of stair cases of Foot Over Bridges including provision of
10mm dia, anchor bar 600mm c/c and fixing with main girder with M.S. flat, making anti-
slip arrangements over the top of nosing as per approved scheme given by Engineer in
charge with all material, labour, T&P as a complete job.
Taking out put 2 Qtl

Material:
including wastage 5%
anchor bars 30X.30X.62=5.58 Kg+5% wastage=5.86 say 6Kg
(Tac welding components and electrodes etc)
Labour:
13,092.00
13,222.92
15,080.74
17,342.85
Total for 200 kgs. 17,516.28
Rate per Kg. Kg 87.58
041070 Providing and fixing various size HTS holding down bolts conforming to IS:1364 in
concrete column or in other structures with proper nuts, bolts, washers/plates,
grouting of holes cement or epoxy concrete with all material, labour, T&P as a complete
job.
041071 With Cement Grout. Cost of cement shall be paid extra.

Total Out put 100 Kgs
Material:

Code (Rs.) (Rs.)
Labour:
8,540.00
Sundries including misc tools and plants Lumpsum 9901 1.00 50.00 50.00
8,590.00
8,675.90
9,894.86
11,379.09
Total for 100 kgs. 11,492.88
Rate per kg Kg 114.93
041072 With epoxy concrete grouting.

Total Out put 100 Kgs
Material:
Epoxy, stone chips etc.for grouting of HTS holding down bolts @ 5% of cost of bolts 0.05 7500.00 375.00
Labour:
8,915.00
Sundries including misc tools and plants Lumpsum 9901 1.00 250.00 250.00
9,165.00
9,256.65
10,557.21
12,140.79
Total for 100 kgs. 12,262.20
Rate per kg. Kg 122.62
041080 Supplying, Fabricating and fixing access ladders, inspection platforms, Trolley refuges
etc., on bridges with structural steel conforming to IS:2062 including welding / bolting,
priming painting with one coat of ready mixed paint of Zinc Chromate (IS:104) with
DFT of 25-30 microns followed by one coat of Zinc Chrome Red Oxide (IS:2074) with
DFT of 25 microns with all material, labour, T&P as a complete job.
Note: Painting shall be paid seperately under relevant item.
Total weight=2.806+.964+.18+.15=4.10MT
Unit = MT
Taking output = 2 x 50 m span = 100 m
Material:
(ISMC 100 = 2.806 x 1.05 = 2.946 MT)
(MS Flat = 0.964 x 1.05 = 1.012 MT)
(MS bars = 0.17 x 1.05 = 0.180 MT)
MS bolts & nuts more than 10 mm dia Quintal 0252 8500.00 1.50 12,750.00
Add for electricity charges, welding and drilling equipment, electrodes and other 228885.00 0.01 2,288.85
consumables @ 1 per cent of cost of material.

Code (Rs.) (Rs.)
Labour:
268,022.85
Sudries, adhesives miscT & P Lumpsum 9901 1.00 650.00 650.00
268,672.85
271,359.58
309,485.60
355,908.44
cost of 4.10 MT 359,467.52
041090 Supplying, fitting and fixing in position true to line and level cast steel rocker/roller
bearing of different load bearing capacity conforming to IS :7666, IS:9565, IS:1030,
IS:919, IS:3073 and IRS Bridge Code including all accessories as per drawing and
Technical Specifications with all material, labour, T&P as a complete job. The payment
shall be made for the load bearing capacity in Metric Tonne as per approved drawing.
Unit : one tonne capacity

Considering a 250 tonne capacity bearing for this analysis
Labour:
Material:
Cast steel rocker bearing assembly of 250 tonne design load capacity duly painted Each 0270 100000.00 1.00 100,000.00
complete with all its components as per drawing and specifications
Add 2 per cent of cost of bearing assembly for foundation anchorage bolts, lifting 0.02 2,000.00
arrangements, grease and other consumables.
105,765.80
105,765.80
106,823.46
121,832.15
140,106.98
Cost of 250 MT Capacity Bearing 141,508.05
041100 Supplying, fitting and fixing in position true to line and level forged steel roller bearing of
different load bearing capacity conforming to IS :7666, IS:9565, IS:1030, IS:919,
IS:3073 and IRS Bridge Code including all accessories as per drawing and Technical
Specifications with all material, labour, T&P as a complete job. The payment shall be
made for the load bearing capacity in Metric Tonne as per approved drawing.
Unit: one tonne capacity

Labour:

Code (Rs.) (Rs.)
Material:
Forged steel roller bearing of 250 tonne design load capacity duly painted complete Each 0271 150000.00 1.00 150,000.00
with all its components as per drawing and specifications
Add 2 per cent of cost of bearing assembly for foundation anchorage bolts, lifting 0.02 3,000.00
arrangements, grease and other consumables.
157,070.30
158,641.00
180,930.06
208,069.57
041110 Supplying, fitting and fixing in position true to line and level sliding plate bearing of
different load bearing capacity with PTFE Surface sliding on stainless steel as per
BS:3784, BS 5400, complete including all accessories as per Drawing and Technical
Specifications with all material, labour, T&P as a complete job.The payment shall be
made for the load bearing capacity in Metric Tonne as per approved drawing.
Unit: one tonne capacity

Labour:
Material:
PTFE sliding plate bearing assembly of 80 tonnes design load capacity duly painted Each 0272 24000.00 1.00 24,000.00
complete with all its components as per drawing and Technical Specifications
Add 2 per cent for foundation anchorage bolts and consumables. 0.02 480.00
28,550.30
28,835.80
32,887.23
37,820.32
041120 Design, supply, fitting and fixing in position true to line and level POT-PTFE bearing of
300MT Capacity, consisting of a metal piston supported by a disc or un reinforced
elastomer confined within a metal cylinder, sealing rings, dust seals, PTFE surface
sliding against stainless steel mating surface, complete assembly to be of cast steel /
fabricated structural steel, metal and elastomer elements complete as per IS:2062,
IS:1030, AISI:304, AISI:316, IS:6911, BS:3784, IS:3400, IS:226, BS-5400, Bridge Code
and as per approved drawing and Technical Specifications. The design of the
bearings shall be submitted by the manufacturers / contractor and got approved from
Railway before fixing. Test report after inspection of the bearings shall be submitted
and got approved before the materials are lifted from the manufacturer premises.
041121 POT-cum -PTFE Bearing (Free end)

Unit: Each Bearing complete assembly
Labour:

Code (Rs.) (Rs.)
Material:
300 MT Capacity Pot Cum PTFE Bearing (Free end ) assembly consisting of a metal Each 0273 57880.00 1.00 57,880.00
piston supported by a disc of un reinforced elastomer that is confined with in the metal
cylinder and sliding assembly comprising of stainless steel attached to metal backing
plate sliding in horizontal plane over PTFE confined in recess(s) on the piston with
internal seal (Brass laminated rings), hard facings, external seal & wiper seal etc
complete with cast steel assemblies/fabricated structural steel assemblies duly painted
with all components complete as per drawings and Technical Specifications.
Add 2 % of cost of bearing assembly, foundation anchorage bolts, transportation and 0.02 1,157.60
misc. items required during fixing.
Sub Total 63,364.77
63,364.77
63,998.42
72,990.20
83,938.72
Rate of 300 MT Capacity Bearing Each 84,778.11
041122 POT Bearing-Fixed Type

Labour:
Material:
300 MT Capacity Pot cum PTFE bearing (Fixed type) assembly consisting of a metal Each 0274 83045.00 1.00 83,045.00
piston supported by un reinforced elastomer confined in the pot with brass ring
sealing making with cast steel assemblies/fabricated structural steel assemblies duly
painted with all components complete as per drawings and Technical Specifications.
Sub Total 89,033.07
89,033.07
89,923.40
102,557.64
117,941.28
041123 POT-cum -PTFE Guided (L)Bearing

Labour:

Code (Rs.) (Rs.)
Material:
300 MT capacity Pot Cum PTFE GUIDED (L) Bearing assembly consisting of a metal Each 0275 101185.00 1.00 101,185.00
cylinder and sliding assembly with guiding arrangement to bear and resist the
horizontal force in the desired direction comprising of stain less steel attached to metal
backing plate sliding in horizontal plane over PTFE confined in recess (s)on the piston
with internal seal (Brass laminated rings),hard facings, external seal & wiper seal etc
Sub Total 107,535.87
107,535.87
108,611.23
123,871.11
142,451.77
041124 POT-cum -PTFE Guided (T)Bearing

Labour:
Material:
300 MT capacity Pot Cum PTFE GUIDED(T) Bearing assembly consisting of a metal Each 0276 96790.00 1.00 96,790.00
with internal seal (Brass laminated rings),hard facings ,external seal & wiper seal etc
103,052.97
104,083.50
118,707.23
136,513.32

Code (Rs.) (Rs.)
250 MT Capacity, consisting of a metal piston supported by a disc or un reinforced

Labour:
Material:
piston supported by a disc of unreinforced elastomer that is confined with in the metal
cylinder and sliding assembly comprising of stain less steel attached to metal backing
plate sliding in horizontal plane over PTFE confined in recess (s)on the piston with
internal seal (Brass laminated rings),hard facings ,external seal & wiper seal etc
Add 2 % of cost of bearing assembly, foundation anchorage bolts, transportation and 0.02 947.60
Sub Total 52,433.58
52,433.58
52,957.91
60,398.50
69,458.27

Labour:
Material:
250 MT Capacity Pot type bearing (Fixed) assembly consisting of a metal piston Each 0278 62045.00 1.00 62,045.00
supported by un reinforced elastomer confined in the pot with brass ring sealing
making with cast steel assemblies/fabricated structural steel assemblies duly painted
Sub Total 67,391.88
67,391.88
68,065.79

Code (Rs.) (Rs.)
77,629.04
89,273.39

Labour:
Material:
250 MT Capacity Pot Cum PTFE GUIDED(L)Bearing assembly consisting of a metal Each 0279 77390.00 1.00 77,390.00
Sub Total 83,043.78
83,043.78
83,874.21
95,658.54
110,007.32

Labour:
Material:
250MT Capacity Pot Cum PTFE GUIDED(T)Bearing assembly consisting of a metal Each 0280 72695.00 1.00 72,695.00
Sub Total 78,254.88
78,254.88
79,037.42

Code (Rs.) (Rs.)
90,142.18
103,663.51

Labour:
Material:
200 MT Capacity Pot Cum PTFE Bearing (Free end) assembly consisting of a metal Each 0281 36655.00 1.00 36,655.00
Sub Total 41,272.88
41,272.88
41,685.61
47,542.44
54,673.80

Labour:
Material:
200 MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston Each 0282 45025.00 1.00 45,025.00

Code (Rs.) (Rs.)
49,810.28
49,810.28
50,308.38
57,376.71
65,983.22
Rate per 200 MT Capacity Bearing Each 66,643.05

Labour:
Material:
200 MT Capacity Pot Cum PTFE GUIDED(L)Bearing assembly consisting of a metal Each 0283 57140.00 1.00 57,140.00
Sub Total 62,167.58
62,167.58
62,789.26
71,611.15
82,352.82

Labour:
Material:
200 MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal Each 0284 52805.00 1.00 52,805.00

Code (Rs.) (Rs.)
57,745.88
57,745.88
58,323.34
66,517.77
76,495.43

Labour:
Material:
Sub Total 29,489.99
29,489.99
29,784.88
33,969.66
39,065.11

Labour:

Code (Rs.) (Rs.)
Material:
150MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston Each 0286 29985.00 1.00 29,985.00
Sub Total 34,248.29
34,248.29
34,590.77
39,450.77
45,368.39

Labour:
Material:
150MT Capacity Pot Cum PTFE Guided (L) Bearing assembly consisting of a metal Each 0287 38745.00 1.00 38,745.00
Sub Total 43,183.49
43,183.49
43,615.32
49,743.27
57,204.76

Labour:

Code (Rs.) (Rs.)
Material:
150MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal Each 0288 35760.00 1.00 35,760.00
Sub Total 40,138.79
40,138.79
40,540.17
46,236.07
53,171.48

Labour:
Material:
100MT Capacity Pot Cum PTFE Bearing (Free end ) assembly consisting of a metal Each 0289 16350.00 1.00 16,350.00
Sub Total 20,119.39
20,119.39
20,320.58
23,175.63

Code (Rs.) (Rs.)
26,651.97

Labour:
Material:
100MT Capacity Pot type bearing (Fixed type) assembly consisting of a metal piston Each 0290 17385.00 1.00 17,385.00
Sub Total 21,175.09
21,175.09
21,386.84
24,391.69
28,050.45

Labour:
Material:
100MT Capacity Pot Cum PTFE Guided (L) Bearing assembly consisting of a metal Each 0291 25625.00 1.00 25,625.00
Sub Total 29,579.89
29,579.89
29,875.69
34,073.22
39,184.21

Code (Rs.) (Rs.)
Labour:
Material:
100MT Capacity Pot Cum PTFE Guided (T) Bearing assembly consisting of a metal Each 0292 23350.00 1.00 23,350.00
Sub Total 27,259.39
27,259.39
27,531.98
31,400.23
36,110.26
041170 Design, supply and fixing 300MT capacity Spherical Bearing in position true to line
and level consisting of set of concave and convex mating steel backing plate with a low
friction sliding interface, flat sliding elements ,guides and restraining rings; with all
components conforming to approved drawing and technical specifications & Bridge
Code including grouting of holes for anchor bolts and underside of baseplate with
approved non-shrink epoxy grout with all material, labour, T&P as a complete job.
Note: Sliding surface with PTFE or UHMWPE low friction thermoplastic material and
steel for backing plate of Mild steel in accordance to IS:2062 grade-B. Cast steel in
accordance with IS 1030 Grade 280-520W. Stain less steel in accordance with AISI
304/316.Low friction thermo -plastic sliding PTFE material either pure
polytetrafluroethalyne (PTFE) Or Ultra High Molecular weight Polythylene (UHMWPE).
Austanitic steel is of stainless steel for the sliding interface shall be in accordance with
AISI 316L or O2 Cr17 NI12 of IS-6911. The thickness of the stain less steel sheet shall
be 3mm minimum.The stainless steel sheet shall be attached to its backing plate either
by screwing/riveting or by continuous fillet weld.Hard chromium plated surface shall be
entire curved surface of the convex steel plate mating with hard chromium plated
concave sliding surface .The thickness of the hard chromium plating shall be at least
100 microns and the final surface roughness of the plated surface shall not exceed 3
microns.Bearing manufacturer shall give the guarantee for satisfactory performance of
bearing for period specified.
041171 Spherical Fixed Bearing

Labour:
Material:

Code (Rs.) (Rs.)
300 MT Capacity Spherical fixed bearing consists of an assembly of precision Each 0293 65185.00 1.00 65,185.00
designed and sized according the specific requirements .The bottom plate with a
spherically concave top face covered with a recessed PTFE sheet .The top component
is a solid stainless steel plate with spherically machined convex bottom face mating
with concave curved surface fixed by restraining rings to restrict the horizontal
movement as a complete unit made up of with Mild steel/cast iron steel/Stainless steel
conforming to IS 2062 Grade -B & IS 1030 Grade 280-520W or 340-570W,AISI
304/316 shall be used for the backing plates with flat or curved surfaces.
Sub Total 70,815.87
70,815.87
71,524.03
81,573.15
93,809.13
041172 Spherical Free Float Bearing

Labour:
Material:
300 MT Capacity Spherical free float bearing consists of an assembly of precision Each 0294 55860.00 1.00 55,860.00
designed and sized according the specific requirements .The bottom plate with a
spherically concave top face covered with a recessed PTFE sheet .The top component
is a solid stainless steel plate with spherically machined convex bottom face mating
with concave curved surface . Sliding assembly attached consists of a polished
stainless sheet welded to the under side of top steel plate slides on PTFE disc
recessed or bonded to the upper surface of convex plate as complete unit made up of
with Mild steel/cast iron steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030
Grade 280-520W or 340-570W,AISI 304/316 shall be used for the backing plates with
flat or curved surfaces, Stainless sheet shall be in accordance with AISI316L OR of IS
6911 of minimum thick 3mm
Sub Total 61,304.37
61,304.37
61,917.41
70,616.81
81,209.33
041173 Spherical Slide Guide (L) Bearing

Labour:

Code (Rs.) (Rs.)
Material:
300 MT Capacity Spherical Slide Guide (L) bearing consists of an assembly of Each 0295 79400.00 1.00 79,400.00
precision machined steel components with spherical concave and convex elements in
its centre designed and sized according the specific requirements .The bottom plate
with a spherically concave top face covered with a recessed PTFE sheet .The top
component is a solid stainless steel plate with spherically machined convex bottom face
mating with concave curved surface . Sliding assembly with guiding system bear and
transmit the horizontal force in one direction and allowing the movement perpendicular
to above (Longitudinal direction) consisting of a polished stainless sheet welded to the
under side of top steel plate slides on PTFE disc recessed or bonded to the upper
surface of convex plate as complete unit made up of with Mild steel/cast iron
steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030 Grade 280-520W or
340-570W,AISI 304/316 shall be used for the backing plates with flat or curved
surfaces, Stainless sheet shall be in accordance with AISI316L OR of IS 6911 of
minimum thick 3mm.
Sub Total 85,315.17
c) Sudries, adhesives misc. T & P and consumables @ 3 per cent on a+b 0.03 2,559.46
87,874.63
88,753.37
101,223.22
116,406.70
Cost of 300 MT Capacity Bearing Each 117,570.77
041174 Spherical Slide Guide (T) Bearing

Labour:
Material:
300 MT Capacity Spherical Slide Guide (T) bearing consists of an assembly of Each 0296 75560.00 1.00 75,560.00
precision machined steel components with spherical concave and convex elements in
its centre designed and sized according the specific requirements .The bottom plate
with a spherically concave top face covered with a recessed PTFE sheet .The top
component is a solid stainless steel plate with spherically machined convex bottom face
mating with concave curved surface . Sliding assembly with guiding system bear and
transmit the horizontal force in one direction and allowing the movement perpendicular
to above (Transverse direction) consisting of a polished stainless sheet welded to the
under side of top steel plate slides on PTFE disc recessed or bonded to the upper
surface of convex plate as complete unit made up of with Mild steel/cast iron
steel/Stainless steel conforming to IS 2062 Grade -B & IS 1030 Grade 280-520W or
340-570W,AISI 304/316 shall be used for the backing plates with flat or curved
surfaces, Stainless sheet shall be in accordance with AISI316L OR of IS 6911 of
minimum thick 3mm
81,398.37
Sudries, adhesives misc. T & P and consumables @ 3 per cent on a+b 0.03 2,441.95
83,840.32

Code (Rs.) (Rs.)
84,678.72
96,576.09
111,062.50
041180 Extra over items 041090 to 041170 for fixing bearings under running traffic /traffic block
including removing of existing bearings and handing over at location as directed..
Add 10% on respective bearing items Each 0.10 0.10
041190 Supply & applying two coats of bitumen emulsion of Grade RS-1, conforming to
IS:8887 on the top surface of concrete deck slab (New bridges) @ 1.70 kg/sqm after
cleaning surface with all materials, labour, tools and plants, equipment etc. complete.
Cost per 20 sqm

Material:
Bitumen emulsion for road of grade RS-1 confirming to IS 8887 MT 0318 37000.00 0.034 1,258.00
Labour:
1,610.00
c) Sundries including misc tools and plants Lumpsum 9901 1.00 30.00 30.00
1,640.00
1,656.40
1,889.12
2,172.49
Cost for 20 Sqm. 2,194.22
Rate of 1.00 sqm Sqm 109.71
041200 Providing road crane of specified lifting capacity with specified jib length revolving type
for material handling, assembly & erection of girders/slab/RCC Box etc.
041201 12 MT capacity
Hire charges of 12 MT crane and accessories Day 0091 6000.00 1.00 6,000.00
Sundries including misc tools and plants (@ 3% of above) 0.03 180.00
6,180.00
6,241.80
7,118.77
8,186.59
Rate per Day Day 8,268.45
8,240.00
8,322.40
9,491.70

Code (Rs.) (Rs.)
10,915.45
20,600.00
20,806.00
23,729.24
27,288.63
Hiring charges of 80MT capacity crane Day 0095 35000.00 1.00 35,000.00
Sundries including misc tools and plants (@ 3% of above) 0.03 1,050.00
36,050.00
36,410.50
41,526.18
47,755.10

51,500.00
52,015.00
59,323.11
68,221.57

103,000.00
104,030.00
118,646.22
136,443.15

180,250.00

Code (Rs.) (Rs.)
182,052.50
207,630.88
238,775.51

231,750.00
234,067.50
266,953.98
306,997.08

257,500.00
260,075.00
296,615.54
341,107.87
041210 Extra for increase in road crane capacity over Item 041209 for every additional 1 MT
capacity or part there of
Details of cost for 1 MT
Machinery
Cost difference for 100 MT 100,000.00
101,000.00
115,190.50
132,469.08
Cost for 100 MT 133,793.77
Rate per 1 MT Day 1,337.94
041220 Surface preparation of steel work of bridge plate/composite girders by cleaning with
scrappers and/or wire brushes to remove all rust and loose or perished paint to prepare
perfectly clean & dry bare metal surface free from all dirt/foreign material & ready for
initial coat of paint. Rate includes cost of labour, consumables, brushes, tools & plants,
ladders, scaffoldings, jhoola, hanging scaffolding staging etc.
a)Taking output=100Sqm

Code (Rs.) (Rs.)
Add for providing, maintainence, slow progress and danger element by using jhoola Lumpsum 9901 1.00 500.00 500.00
etc.
Sub Total 3,287.50
3,327.50
3,360.78
3,832.96
4,407.91
Cost for 100 sqm 4,451.99
041230 Surface preparation of steel work of bridge triangulated girders by cleaning with
scrappers and/or wire brushes to remove all rust and loose or perished paint to prepare
perfectly clean & dry bare metal surface free from all dirt/foreign material & ready for
initial coat of paint. Rate includes cost of labour, consumables, brushes, misc. tools and
plants, ladders, scaffoldings, jhoola, hanging scaffolding, staging etc.
Basic cost as for item 041220 44.52

Add 50% on item 041220 for larger spans and heavier loads and extra height of 0.50 22.26
scaffolding.
041240 Surface preparation for painting of bridge plate/composite girders and other steel
structures where the finishing coat shows signs of deterioration; but primer coat of paint
is sufficiently in good condition and there are no signs of rusting etc. Surface shall be
cleaned free from oil grease, scaling and other foreign matters without disturbing the
primer coat {Rate includes cost of labour, consumables, tools & plants, scaffolding,
jhoola, ladder etc.}

Material :
Wire Brush - 25cm long Each 0313 15.00 3.00 45.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour :
1,637.75
1,654.13
1,886.53
2,169.51
Cost for 100 Sqm surface area 2,191.21

Code (Rs.) (Rs.)
041250 Surface preparation for painting of bridge Triangulated girders where the finishing coat
shows signs of deterioration; but primer coat of paint is sufficiently in good condition
and there are no signs of rusting etc. Surface shall be cleaned free from oil grease,
scaling and other foreign matters without disturbing the primer coat.
Basic cost as for item 041240 21.91

Add 50% on item 041240 for larger spans and heavier loads and extra height of 0.50 10.96
scaffolding.
041260 Painting cleaned plate/composite bridge girders including all scaffolding along with
provision of Jhoola / hanging scaffolding ladders etc. where required.
041261 With one coat ready mix Zinc Chromate conforming to IS:104 with DFT of 25-30
Microns followed by one coat of Zinc Chromate red oxide conforming to IS:2074 DFT of
25 Microns
Material:
Red oxide primer in two coats
Zinc Chromate red oxide Primer to IS:2074 Litre 0308 130.00 0.90 117.00
Labour:
Add for providing, maintainence, slow progress and danger element by using jhoola etc Lumpsum 9901 1.00 80.00 80.00
557.00
Sundries including misc tools and plants (@ 3% of sub-total) 0.03 16.71
573.71
579.45
660.86
759.99
Cost for 10 Sqm. 767.59
041262 With two cover coats of ready-mixed paint conforming to IS:13607 with colour/shades,
as decided by Engineer-incharge
Note: DFT of each coat shall be 20-25 microns
Material:
Ready-mixed paint to IS:13607 with colour/shades, as decided by Engineer-incharge
Ready Mixed Paint as per IS:13607 Litre 0312 230.00 0.91 209.30
Labour:
726.40
748.19
755.67
861.85
991.12

Code (Rs.) (Rs.)
041263 With two coats Aluminium paints in dual containers conforming to IS:2339 with DFT of
12 - 14 Microns for each coat.
Material:
Labour:
608.80
627.06
633.33
722.32
830.67
041264 With two coats of epoxy paint conforming to RDSO spec M&C/PCN/123-11
Note: DFT of each coat shall be 60 microns.
Material:
Epoxy paint as per RDSO Spec M&C/PCN/123-11 Litre 0311 440.00 1.25 550.00
Labour:
1,374.00
1,415.22
1,429.37
1,630.20
1,874.73
041265 With one coat Aluminium paint in dual containers conforming to IS:2339 with DFT of 12 -
14 Microns .
Material:
Labour:

Code (Rs.) (Rs.)
Sundries, Add for providing, maintainence, slow progress and danger element by using Lumpsum 9901 1.00 50.00 50.00
jhoola etc
Sub-total 350.00
360.50
364.11
415.26
477.55
041270 Painting cleaned triangulated bridge girders including all scaffolding, along with
provision of Jhoola / hanging scaffolding ladder where required.
041271 With one coat ready mix Zinc Chromate conforming to IS:104 with DFT of 25-30
Microns followed by one coat of Zinc Chrome red oxide conforming to IS:2074 with
DFT of 25 Microns.
Material:
Labour:
671.40
691.54
698.46
796.59
916.08
041272 With two cover coats of ready-mixed paint conforming to IS:13607 with colour/shades,
as decided by Engineer-incharge.
Note: DFT of each coat shall be 20-25 microns.
Material:
Labour:
840.80
866.02
874.68

Code (Rs.) (Rs.)
997.58
1,147.21
041273 With two coats Aluminium paint in dual containers conforming to IS:2339 with DFT of
12-14 Microns for each coat.
Material:
Labour:
723.20
744.90
752.34
858.05
986.76
041274 With two coats of epoxy paint conforming to RDSO spec M&C/PCN/123-11
Note: DFT of each coat shall be 60 microns.
Material:
Labour:
1,488.40
1,533.05
1,548.38
1,765.93
2,030.82
041280 Extra for working under traffic conditions over items 041220 to 041274
Add 10% over above items Sqm 0.10 0.10

Code (Rs.) (Rs.)
041290 Removing of existing bed plate from existing bed block, supply, fabrication and
erection of new bed plate of approved sizes in exact position over bed block on
pier/abutments by giving full and even bearing, setting them on the layer of free flow
nonshrinkable grouting compound, scrapping or chipping of bed block, if required,
fabrication and fixing of holding down HTS bolts of suitable sizes alongwith nuts,
washers etc., drilling holes of required size, grouting of holes by epoxy mortar after
fixing holding down bolts. Total work to be done during traffic block. Cost of holding
down HTS bolts shall be paid extra under relevant item for supply of HTS holding down
bolts.
041291 Upto 12.2m clear span

Consider MBG plate girder rivetted type Drawing No 16007,the weight of the bearings
(ie Bed plates all together)-0.400MT or 4.00QTL
Material:
Structural steel plates conforming to Grade Designation E250; Quality "B0" as per Quintal 0225 7330.00 4.20 30,786.00
IS:2062,
(Steel considering 5% wastage)
Araldite GY257 Kg 0322 379.50 20.00 7,590.00
Epoxy Hardener HY850 Kg 0323 370.30 20.00 7,406.00
Wooden Blocks 2400 cudm which can be used 10 times i.e. quantity to be taken for
one use = 2400/10 240 cudm.
2nd class deodar wood in scantling 10 Cudm 0344 465.00 24.00 1,116.00
Epoxy mortar for concrete repair kg 0350 25.00 10.00 250.00
Acrylic polymer bonding coat Litre 0352 150.00 1.50 225.00
Labour:
a) Fabrication of bed plate
b) Cleaning and levelling of bed plate seating location
c)Lifting and lowering of girders
Machinery:
hammers
Hire charges for jack of 40 MT lifting capacity Day 0105 800.00 4.00 3,200.00
Hire charges of Arc Welding Machine 500 Amp Day 0132 300.00 1.00 300.00
Hire charges of gas cutter Day 0133 100.00 1.00 100.00
Sundries including misc tools and plants Lumpsum 9901 1.00 5000.00 5,000.00
72,256.70
72,979.27
83,232.85
95,717.78
Cost for 4 qtl.(400 kg.) 96,674.96
041292 More than 12.2m and upto 18.3m clear span

Basic cost same as for 041291 241.69
Add for larger spans and heavier loads and extra height of scaffolding (5% above) 0.05 12.08
253.77

Code (Rs.) (Rs.)
041293 More than 18.3m and upto 30.5m clear span

Basic cost same as for 041291 241.69
Add for larger spans and heavier loads and extra height of scaffolding (10% above) 0.10 24.17
265.86
041294 Supply of HTS holding down bolts with nuts, washer etc.
Considering cost of 1 quintal HTS holding down bolts
7,575.00
8,639.29
9,935.18
Cost for 1 quintal 10,034.53
041300 Assembling and erecting pre-fabricated structures, such as columns, beams, girders,
other members of FOBs and sheds; including leading all structural elements within 1
Km lead, bolting, riveting or welding as per approved drawing or as directed by
Engineer In-charge. Rate shall include cost of labour, materials, tools & plants and only
pre-fabricated structural elements shall be given by Railway. (Work not requiring traffic
or power block).
Detail of cost for 100 MT of pre-fabricated steel structures

Material:
Mild steel rivets for steel girders Quintal 0232 6540.00 30.00 196,200.00
Welding by Electric Plant Cm 0338 1.00 7500.00 7,500.00
Machinery:
Hire charges of Derrick Monkey Rope Day 0061 750.00 60.00 45,000.00
Labour:
556,120.00
561,681.20
640,597.41
736,687.02
Cost for 100 MT 744,053.89
041301 Extra over item no 041300, if the work is to be executed under traffic or power block.
Details of cost for one MT labour cost of item no 041300

Cost for 100 MT
Labour :
25% of labour charges of item no 041300
16,605.00

Code (Rs.) (Rs.)
16,771.05
19,127.38
21,996.49
Cost for 100 MT 22,216.45
041310 Cleaning and greasing of free end and fixed end of steel girder Bridge bearings with
Grease Graphite, Kerosene oil and other materials as per Para 222 of Indian Railway
Bridge Manual 1998 with painting of Bearing as per requirement complete as directed
by engineer in-charge.
Note: One unit shall consists of all bearing of one girder.
041311 Girder of clear span upto 12.2m

Details of cost for 2 girders
Material:
Grease Graphite Grade 'O' (IS:408) Kg 0184 240.00 11.00 2,640.00
Labour:
Machine Operator (Machine) (Skilled) Day 0041 609.00 2.00 1,218.00
12,317.00
Add for working under traffic block @ 5% Lumpsum 9991 0.05 615.85
12,932.85
13,062.18
14,897.41
17,132.03
Cost for 2 girders 17,303.35
Rate per girder Each 8,651.67
041312 Girder of clear span above 12.20m & upto 24.40m

Material:
Labour:
15,345.00
16,112.25
16,273.37
18,559.78
21,343.75

Code (Rs.) (Rs.)
21,557.19
041313 Girder of clear span above 24.40m & upto 30.5m

Material:
Labour:
32,353.00
Add for working under traffic block @ 10% Lumpsum 9992 0.10 3,235.30
35,588.30
35,944.18
40,994.34
47,143.49
041314 Girder of clear span above 30.5m

Material:
Labour:
28,615.00
35,768.75
36,126.44
41,202.20
47,382.53
47,856.36
041320 Launching in position, by any approved method, pre-fabricated Steel Girders, precast
PSC girders/slabs, casted at casting bed developed at site, to correct alignment and
level over the bed block / pedestal with all required arrangements, complete in all
respect.

Code (Rs.) (Rs.)
041321 PSC girders / slabs
Detail of cost for 200.48 MT girder ( for 4 spans of 12.2m with 2 Girder system) =
8*25.06=200.48 MT)
Machinery:
Considering 2 cranes at the site of 150 T capacity for 1 working day.
Hire charges of dozer of 80 HP capacity Hour 0056 500.00 8.00 4,000.00
(Dozer for making approaches)
Labour:
218,630.00
220,816.30
251,840.99
289,617.14
Cost for 200.48 MT girder 292,513.31
041322 Structural steel plate girders

Detail of cost for 114 MT girder ( for 4 spans of 18.3m with 2 Girder system)
=4*28.5=114 MT)
Machinery:
Considering 2 cranes at the site of 100 T capacity for 1 working day.
Labour:
118,630.00
119,816.30
136,650.49
157,148.06
Cost for 114 MT girder 158,719.54
041323 Extra over item no. 041320 if the work is to be executed under traffic/power block.
Extra 10% over 041320

Rate per MT MT 0.10 0.10
041330 DeLaunching of all types of Steel girders, PSC girders/Slabs and stacking away from
river stream or passage as directed by Engineer in charge with all labour, tools and
plant, equipment etc., complete.
041331 PSC girders / slabs
Detail of cost for 200.48 MT girder ( for 4 spans of 12.2m with 2 Girder system) =
8*25.06=200.48 MT)

Code (Rs.) (Rs.)
Machinery:
Considering one crane for 1.5 working day.
Material:
Labour:
167,572.23
191,116.13
219,783.55
Cost for 200.48 MT girder 221,981.38
041332 Structural steel plate girders.

Detail of cost for 114 MT girder ( for 4 spans of 18.3m with 2 Girder system)
=4*28.5=114 MT)
Machinery:
Considering one crane for 1.5 working day.
Material:
Labour:
90,913.10
91,822.23
104,723.25
120,431.74
Cost for 114 MT girder 121,636.06

Code (Rs.) (Rs.)
041340 Delaunching of existing and Launching & fixing of new girder in exact location of all
type of steel/PSC girders/Slabs available at site, during block, complete job including
lifting to any hight as per site requirment, provision of approaches, and placing of
released material away from bridge stream or roads as the case may be.
Note: Payment under this item shall be made for the total weight of girder removed
and newly launched girder.
041341 Delaunching of existing PSC girders / slabs and Launching New PSC girders / slabs
Considering reduction of 20% in cost due to saving in manpower/machinery

simaltaneous delaunching and launching. Cost for 1 MT delaunching with 1 MT
launching
Basic cost of Delaunching of existing PSC girders (041331) 1,107.25
Basic cost of Launching New PSC girders (041321) 1,459.06
Total 2,566.31
Deduct 20% for simultaneous working with the same machinery 0.20 513.26
Net Cost for 2 MT 2,053.05
041342 Delaunching of existing PSC girders / slabs and Launching New Structural steel plate
girders.
launching
Basic cost of Delaunching of existing PSC girders/Slabs (041331) 1,107.25
Basic cost of Launching New Structural steel plate girders (041322) 1,392.28
Total 2,499.53
041343 Delaunching of existing Structural steel plate girders / slabs and Launching New
Structural steel plate girders
launching
Basic cost of Delaunching of existing Structural steel plate girders (041332) 1,066.98
Basic cost of Launching New Structural steel plate girders (041322) 1,392.28
Total 2,459.26
041344 Delaunching of existing Structural steel plate girders / slabs and Launching New PSC
girders / slabs
launching
Basic cost of Delaunching of existing Structural steel plate girders (041332) 1,066.98
Basic cost of Launching New New PSC girders / slabs (041321) 1,459.06
Total 2,526.05


Code (Rs.) (Rs.)
041350 Longitudinally slewing of steel plate girders of span 12.2m to 24.4m under traffic
block at locations where it is found short / excessive expansion gap beyond the
bearing to locking strip or the center of the bearing stiffener not in line with the center
of the bed plate or where the girders ends are butting each other as directed by the
Engineer in charge at site using contractor's own hydraulic jacks of 100 tons capacity
for lifting and slewing of girder separately on both ends to suit as per site conditions,
consumables and wooden cut blocks including transportation, with all contrctors labour,
materials, scaffolding/staging arrangements etc complete without damaging the girder
and track alignment and cross levels.
041351 For Span 12.2M to 18.3M

One girder per day during block hours
Machinery:
Hire charges for OEW flat jack of 100 tons capacity for longitudinal slewing of girder Each 0114 2500.00 2.00 5,000.00
from both sides
Material:
Hydraulic oil SS-68 or equivalent of HPCL/BPCL/IOCL Litre 0183 100.00 3.00 300.00
Diesel (HSD) Oil Litre 0181 101.62 5.00 508.10
2nd class deodar wood in scantling 10 Cudm 0344 465.00 20.00 930.00
Labour:
Add for transportation and Misc. items Lumpsum 9901 1.00 300.00 300.00
18,143.10
18,324.53
20,899.13
24,034.00
Rate per span Each 24,274.34
041352 For Span above 18.3 M to 24.4 M

Basic cost of item 041351 24,274.34
Add for larger spans and heavier loads and extra height (10% over item 041351 1.10 26,701.77
Rate per span Each 26,701.77

Code (Rs.) (Rs.)
041360 Arresting leakage of oil from oil bath tank of rocker and roller bearings where in
segmental rollers immmersed in the oil of nominated OWG bridges of all types of spans
under traffic conditions with contractor's labour, materials, tools and plants, Machinery like
drilling machines and generators, consumables (Engine oil, SAE oil, K-oil, oxygen and
accetylene gas etc), including transpotation etc. complete, by draining left over residue
oil inside of the tank and opening of oil bath tank sides and top dust cover plates and drain
pipes completly by dismantling all its bolted joint connections using chisels and drilling
out bolts if any found sheared and strucked off in the base plate, cleaning of bearings,
rollers, base plates by applying kerosene oil and scrapping, wire brushing and polishing by
zero grade sand paper, examining the rollers and base plates for any micro cracks with
magnifying glasses without causing any damage to rollers and its accessories, refixing
the oil bath tank side and top dust cover plates, drain pipes and its all joint connections
with new bolts using cork sheet and 2mm thick rubber sheet in between joint connections
all along its full length as oil sealent duly correct punching of holes as per site conditions,
applying of epoxy grout over the joint connections to required thick and allowed to set, test
checking for leakages if any by filling the oil bath tank with water during passage of several
trains and after ensuring the pool proof leakage, the Railways supplied oil servo mesh SP
460 BP or equiavalant lubricant to be filled up in the oil bath tank and all bolts to be
tightened firmly and undulations or uneven surfaces of the pier cap to be made level with
cement concrete as directed by the Engineer in charge at site .
Note:
1)Oil removed from the bearngs should be filled in tins and handed over to SSE/BR
concerned,
2)After opening, removal of all existing plates and oil, bearings should be inspected by
Engineer in charge for its confirmation of cut blocks and cleaning in all respects
3)Empty tins are to be handed over to SSE/BR/ concerned.
Machinery:
Hire charges of Rail Drill Machine Day 0137 300.00 2.00 600.00
Hire charges of Generator 5 KVA (without POL) Day 0072 500.00 2.00 1,000.00
Material:
Epoxy mortar for concrete repair kg 0350 25.00 4.00 100.00
Epoxy resin hardener mix for seal coat Kg 0351 150.00 2.00 300.00
Sand Paper Nos. 0496 5.00 20.00 100.00
Luting Sand for AT welding Kg 0420 10.00 20.00 200.00
Nut & Bolts with washers of all sizes Kg 0234 80.00 10.00 800.00
Labour:
Welder (Skilled) Day 0029 609.00 2.00 1,218.00
Add for Lumpsum for transportation, corck sheet, rubber sheet and misc etc Lumpsum 9901 1.00 1000.00 1,000.00
13,382.10
13,515.92
15,414.91
17,727.14
Rate per oil bath bearing Each 17,904.42

Code (Rs.) (Rs.)
041370 Supplying fabricating and erecting welded and/or bolted and/or riveted steel work in
built up sections, trusses and framed work, staging, racks, Height Guage etc.for Steel
Structures other than bridge girders, using RSJ, tees, angles and channels/flats, plates,
gussets, round or square bars, cleats, bolts etc., with contractors own steel including
cutting, bending, straightening, drilling, riveting, hoisting, fixing, erecting, welding,
bolting etc., with Providing stiffeners wherever required as per approved drawing
including applying a priming coat of a approved steel primer with all contractor’s
materials, labour, tools & plants, lead & lift including crossing of tracks if required etc.,
complete as per specification and as directed by Engineer-in-charge.
Note: The payment shall be made on the theoretical weight of main components and
gusset plates only.
Consider for 1MT

Material:
Including 5% wastage
Labour:
67,608.44
Add 3% for consumables and other misc. Lumpsum 0.03 2,028.25
69,636.69
70,333.06
80,214.86
92,247.08
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 5: Bridge Works (Misc.)
CHAPTER - 5 : Bridge Works - Misc.

Code (Rs.) (Rs.)
051010 Providing and laying boulders apron on river bed for protection against scour with
stone boulders weighing not less than 35 kg each with voids filled with spalls
complete as per drawing and Technical Specification.
Material:
Stone boulder, weighing minimum 35 kg each Cum 0213 750.00 1.00 750.00
Stone Spalls Cum 0214 445.00 0.20 89.00
Labour:
1,206.80
1,218.87
1,390.12
1,598.64
051020 Laying of boulder apron laid in wire crates of approved size including overlaps at
joints, laid with stone boulders, all loose ends to be tied with 4mm galvanised steel
wire. Payment for boulders & wire crates to be done extra.
Considering 5.63 Cum

Labour:
2,349.90
2,373.40
2,706.86
3,112.89
Cost of 5.63 cum 3,144.02
051030 Supplying of stone boulders weighing not less than 35 kg each at specified bridge
locations.
Material:
750.00
757.50
863.93
993.52
051040 Supplying Galvanized Wire Net Trungers made from 4mm galvanised steel wire @ 32
kg/10sqm having minimum tensile strength of 300 Mpa conforming to IS:280 and
galvanizing coating conforming to IS:4826, woven into mesh with double twist, mesh
size not exceeding 100mm x 100mm.

Code (Rs.) (Rs.)
taking trunger of size 3x1.5x1.50= Total area=13.5 +2.25+2.25=18.5 Sqm=59.20 kgs
Material:
G.I. wire 4mm dia Kg 0250 70.00 59.20 4,144.00
Labour:
5,270.90
5,323.61
6,071.58
6,982.31
Cost of 18.5 sqm 7,052.14
051050 Providing and laying of Apron with cement concrete blocks cast in-situ and made with
nominal mix of 1:2:4 with all material , labour, tools and plants.
Note: (1) Payment to be made for concrete only; (2) Cement and shuttering to be paid
extra.
Cost of shuttering to be paid extra.

Material:
Labour:
Machinery:

27,493.45
27,768.38
31,669.84
36,420.32
051060 Providing and laying Pitching with Stone Boulders, weighing not less than 35kg each
with voids filled with spalls on slopes, laid over prepared filter media including boulder
apron laid dry in front of toe of embankment complete as per drawing and Technical
Specifications (filter media to be paid separately under the relevant item).

Material:
Stone Spalls Cum 0214 445.00 0.20 89.00
Labour:

Code (Rs.) (Rs.)
1,134.75
1,146.10
1,307.12
1,503.19
051070 Providing and laying Pitching with Stone Boulders, weighing not less than 35kg each
with voids filled with cement sand mortar 1:4 on slopes laid over prepared filter media
including boulder apron laid dry in front of toe of embankment complete as per
drawing and Technical Specifications (filter media to be paid separately under the
relevant item). Rate is excluding cost of cement which shall be paid extra under
relevant item.

Material:
Stone Spalls Cum 0214 445.00 0.20 89.00
Fine Sand (Zone IV) Cum 0203 1000.00 0.35 350.00
Labour:
1,846.95
1,865.42
2,127.51
2,446.64
051080 Providing and laying Filter Material as per RDSO Specifications underneath pitching
in slopes complete as per drawing and Technical Specification.
Material:
Filter media of stone aggregate confirming to RDSO specification (12 cum loose to be Cum 0215 1200.00 1.20 1,440.00
taken as 10 cum after compaction)
Labour:
2,052.50
2,073.03

Code (Rs.) (Rs.)
2,364.29
2,718.93
051090 Laying Boulder Apron on river bed for protection against scour with stone boulders
supplied by Railway with voids filled with spalls complete as per drawings and
Technical Specifications.
Labour:
275.90
278.66
317.81
365.48
051100 Laying Pitching with Stone Boulders supplied by Railway with voids filled with spalls
on slopes, laid over prepared filter media including boulder apron laid dry in front of
toe of embankment as per drawings and technical specifications.
Note: Filter media to be paid under relevant item.

Labour:
295.75
298.71
340.68
391.78
051110 Stenciling of Girders with black / blue lettering over yellow background with ready mix
paint w.r.t. details of executed inspection, greasing and painting, other details as
directed by Engineer in-charge
Note: Payment will be per cm height of each letter
Details of cost for 100 nos.

Material:
Labour:
2,883.00
2,911.83

Code (Rs.) (Rs.)
3,320.94
3,819.08
Cost for 100 nos. 3,857.27
Rate per stencil Each 38.57
051120 Cleaning Surface of Abutment and Piers upto bed level under water with brush or any
other tools to remove all traces of moss, loose materials, fungus, algae, vegetational
growth etc. Cleaning shall be carried out with contractor's trained staff, tools & plants,
safety equipments etc. complete job including arranging safe approach.

Labour:
Hire charges of boat with boatmen Day 0162 1200.00 4.00 4,800.00
8,248.00
8,330.48
9,500.91
10,926.05
Cost for 100 Sqm 11,035.31
051130 Inspecting Sub-structure and Foundation in and around piers & abutments, using
trained and qualified staff, under-water cameras, monitoring sensors & safety
equipments, recording observed defects, e.g. cracks, cavities, bulging, leaning
spalling and other defects noticed in the structure on DVD/Pen drives & photographs
and submitting detailed inspection report to Engineer in-charge. Payment shall be
made on hourly basis of videography & photography.The work shall be executed as
per BS-96.
Detail of cost for 4 hours of videography

Material:
Hiring of video camera
Hiring of still camera
Labour:
3,315.00
3,348.15
3,818.57
4,391.35
Cost for 4 hours of videograpy 4,435.26
Cost per Hour Hour 1,108.82

Code (Rs.) (Rs.)
052000 Flooring in Bridges
052010 Providing and laying flooring with rubble stone, laid over 15cm thick CC 1:2:4 and the
voids filled with CC 1:2:4 complete with the joints pointed with 1:2 Cement Sand
mortar as per drawing and Technical specifications. Payment for cement to be done
separately. Voids in the rubble stone to be taken as 35% of the gross volume of the
stone layer.
Note: Base concrete shall be paid extra under relevant item.

Material:
Stone boulder, weighing minimum 35 kg each Cum 0213 750.00 5.00 3,750.00
Labour:
(i) For laying rubble stone flooring
(ii) For filling voids with Concrete
Machinery:
Hire charges of Generator of 250 KVA capacity Day 0077 3000.00 0.10 300.00
8,866.00
8,954.66
10,212.79
11,744.71
Cost per 5cum 11,862.16
052020 Providing and laying 300mm thick (average) Dry Stone flooring with boulders of not
less than 35kg each in weight, hand packed with surface levelled off to the correct
section with hammer dressing as necessary on the ground including filling the gaps
with quarry spalls and ordinary sand complete including cost of supply of all materials,
labour, lead, lift, tools, plants, crossing of tracks and the like as per drawing and
technical specification as directed by Engineer in charge.

Material:
Stone Spalls Cum 0214 445.00 1.00 445.00
Labour:
(i) For laying dry stone flooring
(ii) For filling gaps with quarry spalls & ordinary sand

Code (Rs.) (Rs.)
7,196.50
7,268.47
8,289.68
9,533.14
Cost per 5cum 9,628.47
052030 Supply and laying of quarry dust including consolidation, supply of all materials,
labour, lead, lift, tools, plants, crossing of tracks as per drawing and technical
specification as directed by the Engineer in charge in case loose slush is encountered
at site of foundation before casting the foundation or laying the filtering media.

Material:
Quarry Dust taking 1.2 Cum for 1cum consolidated thickness.
Labour:
7,612.25
7,688.37
8,768.59
10,083.88
Cost of 10 cum 10,184.72
052040 Supply and laying of coarse sand including consolidation with all labour, lead, lift,
tools, plants, crossing of tracks as per drawing and technical specification as directed
by the Engineer in charge in case loose slush is encountered at site of foundation
before casting the foundation or laying the filtering media.

Material:
Labour:
14,822.25
14,970.47
17,073.82
19,634.90
Cost 10 cum 19,831.25

Code (Rs.) (Rs.)
052050 Guniting concrete surface with cement mortar of average thickness 25mm along with
wire mesh 50x50x3mm, applied with compressor after cleaning surface and spraying
complete including curing as per procedure and technical specifications given under
para 209.3 of IRBM. Rate is excluding the cost of cement which shall be paid extra.
Taking output = 1sqm

Assuming thickness 25 mm
Material:
Wire mesh size 50mm x 50mm of 3mm wire Kg 0354 80.00 2.00 160.00
Accelerator compound for guniting Kg 0347 140.00 0.64 89.60
Labour:
Machinery:
/ hammers
423.19
427.42
487.47
560.60
052060 Providing and inserting nipples of size 12 to 20 mm dia. with approved fixing
compound after drilling holes for grouting as per Technical Specifications including
subsequent cutting/removal and sealing of the hole as necessary after completion of
grouting.
Taking output = 12 Nos.

Assuming thickness 25 mm
Material:
GI/MS nipple size 20mm dia Each 0348 15.00 12.00 180.00
Sundries for Cement, fixing compound and consumables Lumpsum 9901 1.00 40.00 40.00
Labour:
(Mazdoor for fixing and sealing nipples and cutting and removing of surplus legth of
nipples.)
Machinery:
/ hammers
543.45
548.88
626.00
719.90
Cost for 12 per nipples 727.10
Rate per nipple Each 60.59

Code (Rs.) (Rs.)
052070 Grouting of masonry/concrete by injection process duly Sealing of cracks, through
nipples complete as per Technical Specification and procedure given in IRBM Para
No 209 including necessary admixutre. Payment shall be as per use of cement by
weight in case of neat cement/cement mortar grouting and weight of Epoxy in case of
Epoxy Grouting. (Cement wil be paid extra).
052071 Neat Cement Grout with 20% anti shrinkage compound w.r.t. cement.
Taking output for using 1 kg of cement.
Material:
Admixture (anti shrinkage compound) for CC/RCC work Kg 0193 140.00 0.22 30.80
Labour:
Machinery:
Hire charges of grout pump with agitator and accessories Hour 0110 500.00 0.10 50.00
219.80
222.00
253.19
291.17
052072 Cement Sand Mortar (1:1) Grout with 20% anti-shrinkage compound w.r.t. cement.
Taking output for using 10 kg of cement.

Material:
Screened Sand Kg 0204 2.50 11.00 27.50
Admixture (anti shrinkage compound) for CC/RCC work Kg 0193 140.00 2.20 308.00
Labour:
Machinery:
825.75
834.01
951.19
1,093.86
Cost for 10 kg 1,104.80
052073 Epoxy Grout

Taking output = 1 kg
Material:
Crack filling epoxy for guniting and pressure grouting work Kg 0346 650.00 1.10 715.00
Labour:

Code (Rs.) (Rs.)
Machinery:
Hire charges of cement / epoxy slurry injection machine Day 0085 600.00 0.10 60.00
919.00
928.19
1,058.60
1,217.39
Rate per kg Kg 1,229.56
052080 Applying epoxy mortar over leached, honey combed and spalled concrete surface
and exposed steel reinforcement complete as per Technical Specification with
average thickness of 10mm including priming coat, mortar plaster and seal coat of
epoxy.
Taking output = 10 sqm

Assumeaverage 10mm thickness of epoxy mortar
Material:
Epoxy resin hardener mix for seal coat Kg 0351 150.00 25.00 3,750.00
Epoxy mortar for concrete repair kg 0350 25.00 120.00 3,000.00
Labour:
10,560.20
10,665.80
12,164.35
13,989.00
Rate per sqm Sqm 1,412.89
052090 Applying shotcrete mixture of average thickness 40mm over masonry / concrete
including removal of defective concrete, raking the mortar in joints, cleaning the
surface thoroughly, fixing 50x50x3mm wire mesh over the surface for application of
grout mixture comprising cement, sand,coarse aggregate, water, quick setting
compoud complete as per procedures and specifications given in IRBM Para No
209(3) including curing. Rate is excluding the cost of cement which shall be paid
extra.
Taking output = 1 sqm for an average thickness of 25mm.

Material:
Wire mesh size 50mm x 50mm of 3mm wire Kg 0354 80.00 2.00 160.00
Accelerator compound for guniting Kg 0347 140.00 0.64 89.60
Labour:

Code (Rs.) (Rs.)
Machinery:
/ hammers
470.19
474.89
541.61
622.86
052100 Applying pre-packed cement based polymer mortar of strength 45 Mpa (28 days) for
replacement of spalled concrete with average thickness of 10mm as per
manufacturer's specification and approved procedure.
Assumed thickness - 10 mm maximum
Material:
Pre packed cement based polymer mortar of strength 45 Mpa at 28 days Kg 0353 22.00 120.00 2,640.00
Labour:
3,460.20
3,494.80
3,985.82
4,583.69
052110 Providing & applying epoxy with pot life not less than 60-90 minutes for bonding of
new concrete with old concrete @ 0.80 kg/sqm and as per specifications including
cleaning the surfaces complete as per approved procedure.

Material:
Crack filling epoxy for guniting and pressure grouting work Kg 0346 650.00 8.24 5,356.00
Labour:
5,936.20
5,995.56
6,837.94
7,863.63
052120 Providing & fixing 12 mm rabbit wire mesh at the junction of RCC where specifically
ordered or as shown in the drawing

Code (Rs.) (Rs.)
Taking out put 50 Sqm
Material:
Rabbit wire mesh considering 10% for overlaps and wastage.
Wire mesh (Rabbit) Sqm 0355 67.20 55.00 3,696.00
Labour:
4,866.50
4,915.17
5,605.75
6,446.61
052130 Providing weep holes by making suitable opening or drilling in existing Brick Masonry
/ Plain / Reinforced Concrete abutment, wing wall/return wall with 110 mm dia UPVC
pipe (working pressure 4kg/sqcm) extending through the full width of the structure
complete and repairing the same with cement mortar 1:2 (1 cement : 2 coarse sand).
Rate is excluding the cost of cement which shall be paid extra.

Material:
For cement mortar 1:2
Labour:
Machinery:
/ hammers
8,973.15
9,062.88
10,336.22
11,886.65
Cost for 30 m 12,005.52
052140 Providing and fixing of Drainage Spouts of 110mm UPVC Type A ISI marked
(Working pressure 4 kg/sqcm) using suitable clamps and adhesive etc., complete.


Code (Rs.) (Rs.)
Material:
{Including wastage @ 10%}
Synthetic Rubber based Adhesive Litre 0320 200.00 0.50 100.00
Labour:
Add sundries for clamps and scafolding etc. Lumpsum 9901 1.00 160.00 160.00
7,531.15
7,606.46
8,675.17
9,976.44
Cost for 30 m 10,076.21
052150 Providing and laying of filter media consisting of granular materials of GW, GP, SW
groups as per IS:1498 (latest) in required profile behind boulder filling of abutments,
wing walls / return walls etc. above bed level with all labour and material complete job
as per drawing and technical specification of RDSO Guidelines.

Material:
Filter Media of stone aggregate conforming to RDSO specifications (12 cum loose to
be taken as 10 cum after compaction)
Filter media of stone aggregate confirming to RDSO specification (12 cum loose to be Cum 0215 1200.00 12.00 14,400.00
taken as 10 cum after compaction)
Labour:
Bandhani (Semi skilled) Day 0022 505.00 1.00 505.00
Machinery:
Hire charges of Vibratory Hand Rammers / compactors Day 0084 450.00 1.00 450.00
17,540.60
17,716.01
20,205.10
23,235.87
Cost of 10 cum 23,468.23
052160 Removing all loose concrete, cleaning rust with dusting compound & water jet, drying,
replacing worn out reinforcements by welding new reinforcement for making up lost
steel section, applying approved anti-corrosive polymer coating over the damaged
area to proper profile, providing polymer mortar (upto 20mm thickness) or polymer
concrete (more than 20mm thickness) consisting of cement, sand, 6mm down chips
where required and polymer as per manufacturers' specification. The rate includes
curing for 14 days, all materials, consumables, labours, tools and plants,
scaffolding/staging with all lead and lift. Cost of cement & inforcement to be paid
separately.

Code (Rs.) (Rs.)
052161 20mm thick polymer mortar
Taking output = 10 sqm for an average thickness of 20 mm.
Material:
Pre packed cement based polymer mortar of strength 45 Mpa at 28 days Kg 0353 22.00 240.00 5,280.00
Labour:
Machinery:
13,220.05
13,352.25
15,228.24
17,512.48
052162 20mm - 50mm thick polymer concrete

Taking output = 10 sqm for an average thickness of 40 mm.
Material:
Pre-packed polymer concrete based on epoxy system complete with curing Kg 0349 10.00 500.00 5,000.00
compound, initiator and promoter
Labour:
Machinery:
9,646.50
9,742.97
11,111.85
12,778.63
052170 Supply, fabrication and erection of steel members to replace existing corroded
members of built up section made up of MS plate, angles, channels of different
thickness and sizes including painting with one coat of ready mix paint Zinc Chromate
priming to IS:104 followed by one coat of ready mix paint red-oxide Zinc Chrome
primining paint to IS:2074. Structural steel should conform to IS:2062 E250-
Grade'B0'. Fabrication and erection to be as per existing design initially by bolts and
nuts and finally by rivetting during the sanctioned traffic block. Rate includes cutting
of new steel work, removal of rivets by drilling, dismantling of any existing members
required for inserting fabricated members, fixing of new fabricated built up members
with all tools, plants, labour, consumables, machinery and accessories etc. Work will
be executed as per IRS:B 1-2001.
Note: Painting shall be paid extra under relevant item.

Code (Rs.) (Rs.)
Taking output = 800 kgs = 8 Qtls.
Material:
Add 3% of the cost of materials for rivetting 48125.70 0.03 1,443.77
Cost of making scaffolding, shifting to different locations of work under traffic etc @ 48125.70 0.10 4,812.57
10% of cost of material
Labour:
Machinery:
/ hammers
90,922.04
91,831.26
104,733.55
120,443.59
Cost for 8 qtl 121,648.02
Cost per qtl 15,206.00
052180 Supplying and changing of corroded worn-out and loose rivets of any size at any
location of the bridges with or without traffic blocks including all tools, plants,
machinery complete in all respects.
052181 For Rivets of size upto 25mm dia.
Taking Output=100 nos
Material:
Labour:
Machinery:
/ hammers
15,463.00
15,617.63
17,811.91
20,483.69
cost per 100 Rivets 20,688.53
Rate per Rivet Each 206.89
052182 For Rivets of size more than 25mm dia.

Taking Output = 100 nos
Material:

Code (Rs.) (Rs.)
Labour:
Machinery:
/ hammers
25,804.20
26,062.24
29,723.99
34,182.59
cost per100Rivets 34,524.41
Rate per rivet Each 345.24
052200 Painting the HFL mark and Danger level mark, year of HFL on bridge abutments and
piers with ready mixed paint as per standard in two coats over one coat of primer with
all materials, labour, tools, scaffolding, all lead and lift etc. including writing complete.
Taking progress as 10 marks/day including base and two coats of paint with markings
Material:
Labour:
1,891.00
1,909.91
2,178.25
2,504.99
Cost of 10 mark 2,530.04
Rate per mark Each 253.00
052210 Providing cast in situ bridge number plaques as per Railway drawing in cement
concrete 1:2:4 mix using 20mm hard stone aggregate embedded in 30mm notch in
Bridge parapet coping duly engraving the letter and figures and an arrow indicating
the direction of flow and finishing the top exposed surface with cement mortar 1:3,
painting letters and figures with two coats of black enamel paint on two coats of white
background with all labour, tools, cement, paint etc. with all leads and lifts.
Taking progress as 10 Bridge No plaques including fi and two coats of paint with
markings
Material:
Precast Concrete bridge No plaque/ stone Each 0498 287.50 10.00 2,875.00
Labour:
5,498.00
5,552.98

Code (Rs.) (Rs.)
6,333.17
7,283.15
Cost of 10 plaque 7,355.98
Rate per plaque Each 735.60
052220 Providing cast in-situ plaques for bridge foundations details of size 45cmx45cmx5cm
in cement concrete 1:2:4 mix using 20mm hard stone aggregate embedded in 30mm
deep notch over abutment & piers, engraving the letters & figures with CM 1:3 and
finished smooth including painting letters and figures with 2 coats of black enamel and
plaque with white enamel with all labour, tools, cement, paint, curing etc. as a
complete job.
Taking progress as 10 foundation detail plaques including egraving numbring and

two coats of paint with details of foundations
Material:
Precast Concrete bridge foundation details plaque including engraving complete Each 0499 525.00 10.00 5,250.00
Labour:
8,502.00
8,587.02
9,793.50
11,262.52
Cost of 10 plaque 11,375.15
Rate per plaque Each 1,137.51
052230 Providing & laying non pressure NP-4 Class RCC pipe with collars, jointing with 1:2
cement and ordinary sand mortar including testing of joints, but excluding earthwork
with all labour and material as a complete job. Cement for mortar will be paid
separately.(Pipes of 600mm dia and above will be laid using crane/hydra).
052231 300mm dia.

Taking output 100 mts (with 5% wastage)

Code (Rs.) (Rs.)
Material:
NP 4 Class RCC pipe 300mm dia Metre 0363 600.00 105.00 63,000.00
Labour:
69,275.00
69,967.75
79,798.22
91,767.95
Cost of 100 metre 92,685.63
052232 450mm dia.

Material:
Labour:
108,875.00
109,963.75
125,413.66
144,225.71
Cost of 100 metre 145,667.96
052233 600mm dia.

Material:
Labour:
184,463.00
186,307.63
212,483.85
244,356.43
Cost of 100 metre 246,799.99

Code (Rs.) (Rs.)
052234 900mm dia.

Material:
Labour:
353,249.00
356,781.49
406,909.29
467,945.68
Cost of 100 metre 472,625.14
052235 1000mm dia.

Material:
Labour:
451,286.00
455,798.86
519,838.60
597,814.39
Cost of 100 metre 603,792.53
052236 1200mm dia.

Material:
Labour:
602,124.00
608,145.24
693,589.65
797,628.09

Code (Rs.) (Rs.)
Cost of 100 metre 805,604.37
052237 1800mm dia.

Material:
NP 4 Class RCC pipe 1800mm dia Metre 0369 13300.00 105.00 1,396,500.00
{Considering wastage of 5%, quantity = 105 metres}
Labour:
1,428,164.00
1,442,445.64
1,645,109.25
1,891,875.64
Cost of 100 metre 1,910,794.40
052240 Supplying, spreading and filling coarse sand (no cohesive materials to be used) of
approved quality including watering and ramming in foundation, behind the abutment,
wing wall, retaining wall in layers not exceeding 150mm thick including its compaction
as per direction of Engineer-in-charge. The rate includes all lead, lift, ascent, descent,
crossing of Railway line etc. complete with contractor’s labour, materials, tools and
plant.
Taking output = 10 cum.

Materials:
Labour:
15,737.37
15,894.74
18,127.96
20,847.15
Cost of 10 cum 21,055.62
Rate per metre Cum 2,105.56
052250 Providing Boulder Backing behind wing wall, return wall, retaining wall with hand
packed boulders & cobbles with smaller size boulders toward the back including all
lead, lift, labour & other incidental charges as complete work in all respect. Payment
for boulder/cobbles will be done extra.
Taking output = 10 cum.

Labour:

Code (Rs.) (Rs.)
2,430.60
2,454.91
2,799.82
3,219.79
Cost of 10 cum 3,251.99
Cost per cum Cum 325.20
052260 Dewatering of natural or accumulated water from any location. Payment to be done
for Horse power of pump multiplied by pumping hours.
Taking output HP Hours = 5X6 = 30 HP Hours
Hire charges of pump set of capacity 4000 litre per hour Day 0086 900.00 1.00 900.00
910.00
919.10
1,048.23
1,205.47
Cost of 30 hrs 1,217.52
Rate per hour per HP HP Hour 40.58
052270 Supplying & fixing Galvanised Steel Wire Ropenet, made of 9mm dia. steel wire rope
having aperture size of 45cm x 60cm with 6m long hangs for top anchoring and 5m
wide alongwith chain-link mesh-netting of 80mm x 80mm mesh size made from
2.4mm dia galvanised wire, joining of chain-link mesh & steel wire ropenet and joining
of adjacent nets with galvanised spiral lock springs of steel wire dia 2.2mm; inner dia.
of springs 18mm; total length 50mm ± 0.5mm; pitch 4mm & open end length 60mm
including cutting of tree/shrub etc. in rope-netting location and also, excavation /
filling-back of trenches in all types of soil after anchoring ropenet with RCC pre-cast
beam of size 15cm x 15cm x 2m of M-15 concrete & 30cm thick M-10 PCC. This work
also includes supply of 200mm x 200mm x 6mm epoxy coated washer plates with
12.5mm / 18mm dia. hole at centre and supplying & fixing of anchor bolts/fastners of
10mm dia. including drilling of holes upto a depth of 110mm in rock; cleaning of holes;
fixing of fastners with nut & epoxy coated washer plates; applying torque 65 to 70
N/mm for fixing of ropenet for intermediate anchoring on the surface of cutting,
bottom anchoring upto 1m depth by using 16mm dia. HYSD steel bolts, threaded upto
200mm on top and fixing epoxy coated washer plate, fabrication & fixing of U-pin on
top of cutting for top anchoring and joining of adjacent nets with spiral spring and
fixing at the ratio of 1 no. per 0.6m in longitudinal direction of net portion and
additional locks for lacing chain link netting with ropenet with contractor's materials,
machinery, tools & plants, cement, steel, labour, lead, lift, transportation, ascent,
descent, taxes, royalty etc. complete as per directions of engineer-in-charge.
Note: Concrete will be paid separately under relevant item.
Material:
Galvanised steel wire mesh rope net made of 9mm dia steel wire rope having Sqm 0362 468.00 100.00 46,800.00
aperture size of 45cm x 60cm with 6m length hangs
Galvanised chain link mesh netting of 80mm x 80mm mesh size Sqm 0357 180.00 100.00 18,000.00
Galvanised spiral lock spring Each 0358 19.20 15.00 288.00
Epoxy coated washer plate of 200mm x 200mm x 6mm size Each 0359 156.00 32.00 4,992.00
Anchor fastener of 10mm dia and 110mm length Each 0360 72.00 20.00 1,440.00
Bottom anchors of 16mm dia HYSD & 1m length Each 0361 276.00 12.00 3,312.00
U pin of 6mm dia mild steel of 0.3m length for stone cladding work Each 0493 14.00 33.00 462.00
Labour:

Code (Rs.) (Rs.)
Machinery:
/ hammers
86,100.00
86,961.00
99,179.02
114,055.87
115,196.43
Cost for 100 Sq.m. 115,196.43
052280 Supplying & placing of Mechanically Woven Double Twisted Hexagonal Shaped Wire
Mesh Gabion Boxes of required sizes, Mesh Type 10cm x 12cm, Zn and PVC coated
Mesh Wire dia. 2.7/3.7mm (ID/OD), edges of meshes mechanically edged / selvedged
with heavy coating of galvanization as per EN 10223-3/ASTM A 975 with partitions at
every 1m interval and properly packed with approx. 150mm size boulders including
transportation and placing at indicated places as per direction of engineer-in-charge
including contractor's tools, plants, labour, royalty charges etc. complete in all respect
and stitching with lacing wire of dia. 2.2/3.2mm (ID/OD) @ 5% by weight of Gabion
boxes, carrying the material by head load from nearest approach with all safety
precautions and all leads and lifts.
Cost for 100 cum

Material:
Mechanically woven double twisted hexagonal shaped wire mesh gabion boxes of Cum 0180 1495.00 100.00 149,500.00
required sizes with 10mm x 12mm mesh of wire dia 2.7mm/3.7mm (ID/OD) and Zn &
PVC coated
Labour:
Stone Chiseller (Semi skilled) Day 0017 505.00 4.00 2,020.00
235,950.00
238,309.50
271,791.98
312,560.78
Cost for 100 cum 315,686.39

Code (Rs.) (Rs.)
052290 Supplying & placing partly or fully underwater of Polypropylene Tarred Rope Gabion,
fabricated from 9mm dia. rope, 100mm x 100mm Mesh with partitions at every 1m
interval and properly packed with approximately 150mm size boulders including
transportation and placing at indicated places as per direction of engineer-in-charge
with contractor's tools, plants, labour etc. including royalty charges complete in all
respect and stitching with polypropylene lacing rope of minimum dia. 4mm; carrying
the material by head load from nearest approach with all safety precautions and all
leads and lifts.
Cost for 100 Cu.m.

Material:
Poly propylene tarred rope gabion fabricated from 9mm dia rope 100m x 100m mesh Cum 0497 1380.00 100.00 138,000.00
with partition at every 1m interval
Labour:
Stone Chiseller (Semi skilled) Day 0017 505.00 4.00 2,020.00
226,174.00
228,435.74
260,530.96
299,610.61
Cost for 100 cum 302,606.71
053000 SURFACE PROTECTION OF BRIDGES

053010 Surface protection of Piers, Substructure, Box bridges and culverts in river bed by
cleaning & preparing the surfaces by acid etching; treating surface with a two-layer
plaster; first layer of 7mm (5mm in case of sidewalk) thick with cement (OPC or slag)
admixed with an octadecanoic acid based cementitious waterproofing compound
(Max. bulk density 0.5 gm/cc), in the weight ratio of 50:3 for cement and
waterproofing compound and second layer of 12mm thick cement-sand (1:2.5)
plaster, enriched with polyester fibre (to be paid separately) and curing the plastered
surface. Treatment shall be impermeable under a water head of 20m. Rate is
excluding cost of cement which shall be paid extra.
Note: In lieu of etching with acid the surface can be roughened or bond improved by
other appropriate means complete as per specification.
053011 Piers, substructure, Box bridges and culverts in river bed

Cost of 1sqm
Material:
Waterproofing compound Kg 0195 207.00 0.84 173.88
Muriatic Acid Kg 0196 23.00 1.00 23.00
Tools, plants and other consumables Lumpsum 9901 1.00 10.00 10.00
Labour:
569.08
574.77

Code (Rs.) (Rs.)
655.53
753.86
053012 Side walks

Cost of 1sqm
Material:
Muriatic Acid Kg 0196 23.00 1.00 23.00
Tools, plants and other consumables Lumpsum 9901 1.00 10.00 10.00
Labour:
519.40
524.59
598.30
688.04
053020 Surface protection of Underside of Bridge Decks, Girders, Inside of Box Girders,
Railings etc. of Bridges and Piers and Substructures which are not in River Bed by
cleaning and drying the surface; repairing local defects, e.g. honeycombs with a paste
of cement admixed with 5% by weight of cement of Polymer bonding agent, applying
(@ 0.30 litre/sqm) a coat (DFT of 100-150 micron) of a translucent brown coloured
modified phenolic resin based single component high performance polymeric
waterproofing compound (sp. gr. 0.87, resin content nil and a solid content of
minimum 0.47%), applying (@ 0.25 litre/sqm) a top coat of a modified phenolic resin
based single component waterproofing compound of grey or other shades (sp. gr.
0.85) before the base coat becomes tack-free; permitting the coatings to cure and dry
naturally; the 2-coat system shall be impermeable under a water head of 20m,
complete as per specification.
Cost of 1 sqm
Material:
Surface protection material ESI Permaproof Litre 0197 253.00 0.30 75.90
Surface protection material ESI Permacil -GA Litre 0198 272.55 0.25 68.14
Surface protection material ESI Bond Litre 0199 278.30 0.05 13.92
Labour:
328.19
331.47
378.05

Code (Rs.) (Rs.)
434.75
053030 Surface protection of Bridge Deck by cleaning and preparing the surface by acid
etching; treating the surface with a two-layer plaster; first layer of 5mm thick with
cement (OPC or slag), admixed with an octadecanoic acid based cementitious
waterproofing compound (bulk density not greater than 0.5 gm/cc) in the weight ratio
of 50:3 for cement and waterproofing compound, further enriched with specially
fabricated deformed galvanized steel fibre @ 150 gm/sqm of treated surface and
second layer of 12mm thick cement-sand (1:2.5) plaster, enriched with polyester fibre
(to be paid separately) and curing the plastered surface. Treatment shall be
impermeable under a water head of 20m complete as per specifications. Rate is
excluding cost of cement which shall be paid extra.
Cost of 1sqm
Material:
Muriatic Acid Kg 0196 23.00 1.00 23.00
Galvanised steel fibre Kg 0356 200.00 0.15 30.00
Tools, implements and other consumbables Lumpsum 9901 1.00 10.00 10.00
Labour:
527.85
533.13
608.03
699.24
053040 Designing and developing Detailed structural and working Drawings for following
items for ROB/RUB/Bridge based on Railway's approved GADs, duly collecting
necessary data from Railways and R&B authorities, duly designing members and
submission of check plot duly getting proof-checked by Railway approved institutes,
submitting for Railway's verification and approval, making corrections duly
incorporating suggestions in drawings/designs, further submission of original in
transparent film paper and soft copy (CD) for Railways approval etc. with contractor's
technical expertise and instruments, labour, consumables, repeatedly attending till
final approval etc., complete as directed by Engineer in-charge.
053041 Open / Pile / Well Fondation for piers/abutments

Detail of cost for one set of design & drawings
Material:
Designing and developing detailed structural and working Drawings for open / Pile / Set 0370 17250.00 1.00 17,250.00
well foundation for RCC column / piers for ROB/RUB/Bridges, based on Railway's
approved GADs, duly designing the members and submission of check plot duly
getting proof checked by Railway approved institutes.

{Expenses for site visits etc.} 18,250.00
18,432.50

Code (Rs.) (Rs.)
21,022.27
24,175.61
Rate for one set of design & drawings Set 24,417.36
053042 RCC Bed Block

Material:
Designing and developing detailed structural and working Drawings for RCC bed Set 0371 5175.00 1.00 5,175.00
block for ROB/RUB/Bridges, based on Railway's approved GADs, duly designing the
members and submission of check plot duly getting proof checked by Railway
approved institutes.

5,731.75
6,537.06
7,517.62
053043 Foundation and sub-structure for RCC retaining wall, abutment and approach slab

Material:
Designing and developing detailed structural and working Drawings for foundation Set 0372 17250.00 1.00 17,250.00
and sub structure for RCC retaining wall, abutment and approach slab for
ROB/RUB/Bridges, based on Railway's approved GADs, duly designing the members
and submission of check plot duly getting proof checked by Railway approved
institutes.

17,927.50
20,446.31
23,513.26
053050 Extra for providing and mixing synthetic Polyester triangular synthetic fibre in
specified ratio (@ 0.25% of cement by weight), 6 to 18mm in length, designed for
melting point 240°C to 260°C and specific gravity of 1.33 to 1.40 in all types of work
CC/RCC/plaster etc., This item shall only be used on specific instructions of
Engineer-in-Charge.
Material:
Synthetic polyester triangular fibre of length 6 mm, effective diameter 10-40 microns Kg 0194 400 1.000 400.00
and specific gravity of 1.34 to 1.40.
400.00
404.00
460.76
529.88
Rate per 1 kg of fibre Kg 535.18
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 6: Rail, Sleepers Fittings Renewals
CHAPTER 6 : Rails, Sleepers & Fittings Renewal

Code (Rs.) (Rs.)
061000 1. Rails
061010 Pulling & positioning of rails accurately on cess including supporting rails, providing
required gap and squaring at ends for renewal preparation, as directed by Engineer in-
charge.
061011 Upto 40 m long rail panel
Details of cost for 1040 TM, i.e. 40 rail panels of 26m each on both sides of track to
be tackled in a shift of 8 hrs. working. 4 rail dollies to work for one rail panel of upto
26m length and 3 men to work on one rail dolly. Thus, total 24 men required for both
side rail panels in one day for tackling 1040 track metre stretch.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Look Out Man (Un-skilled) Day 0033 431.00 1.00 431.00
Waterman (Un-skilled) Day 0034 431.00 1.00 431.00
Misc.:
T & P (Rail tongue, Crow bar, Rail Dolly etc.) @1% on labour cost Lumpsum 9901 1.00 120.00 120.00
11,935.00
12,054.35
13,747.99
15,810.18
Cost for 1040 Running Metre 15,968.29
Rate per RM RM 7.68
061012 More than 40 m long rail panel

Details of cost for 3120 TM, i.e. 24 rail panels of average 130m each on both sides of
track to be tackled in a shift of 8 hrs. working. (20 rail dollies to work for one rail panel
of 130m length and 3 men to work on one rail dolly. Thus, total 120 men required for
both side rail panels in one day for tackling 3120 track metre stretch.)
Labour:
Mate (Skilled) Day 0002 609.00 4.00 2,436.00
Waterman (Un-skilled) Day 0034 431.00 4.00 1,724.00
Misc.:
T & P (Rail tongue, Crow bar, Rail Dolly etc.) Lumpsum 9901 1.00 240.00 240.00
56,551.00
57,116.51
65,141.38
74,912.59
Cost for 3120 TM 75,661.71
Cost for 1 Running Metre RM 12.13
061013 Extra to Item no. 061011 for working on bridge

Details of cost for 1040 TM, i.e. 40 rail panels of 26m each on both sides of track to
be tackled in a shift of 8 hrs. working and 6 rail dollies shall work for one rail panel of
upto 26m length @ 3 men per rail dolly. Thus, total 36 men required for both side rail
panels in one day for tackling 1040 track metre stretch. Since 24 men were taken in
item 061011, additional 12 men will be required.

Code (Rs.) (Rs.)
Labour:
Misc.:
5,196.00
5,247.96
5,985.30
6,883.09
Cost for 1040 Track Metre 6,951.92
061014 Extra to Item no. 061012 for working on bridge

Details of cost for 3120 TM, i.e. 24 rail panels of average 130m each on both sides of
track to be tackled in a shift of 8 hrs. working needing 30 rail dollies to work for one
rail panel of 130m length @ 3 men per rail dolly.
Thus, total 180 men required for both side rail panels in one day for tackling 3120
track metre on bridge i.e. 60 more labour than 120 labour provided in 061012.
Labour:
Misc.:
25,980.00
26,239.80
29,926.49
34,415.47
061020 Dismantling and removing rail of all types & length from track, laid on any type &
density of sleeper by removing fish plates, fastenings & fish bolts and other materials
including stacking all released materials as directed by Engineer in-charge.
Note:
1.Cutting of rails shall be paid separately.
2.Work to be done under traffic block.
061021 For Through Renewal work

Details of cost for 520 TM in one day
Labour:
(i) For Dismantling of rail during block period
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For clearing infringement & stacking of released materials, additional labour
requirement over (i) above for the activity in non-block periood.
Misc.:
T&P Lumpsum 9901 1.00 58.00 58.00
13,938.50

Code (Rs.) (Rs.)
14,635.43
14,635.43
14,781.78
16,858.62
19,387.41
Cost for 520 TRM 19,581.29
Cost for 1 TRM TRM 37.66
061022 For Casual/Scattered Renewal work

Details of cost for 350 Running Metre in one day
Labour:
(i) For Dismantling of rail {during block period}
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For clearing infringement & stacking of released materials, additional labour
requirement over (i) above for the activity in non-block periood.
T&P Lumpsum 9901 1.00 34.00 34.00
7,449.50
7,821.98
7,900.19
9,010.17
10,361.70
061030 Insertion of rails of all types & length in track, laid on any type & density of sleeper to
the specified gauge under traffic block. Rates include fastning of rail with sleepers
with standard set of fastenings and fixing of fish plates and bolts or, if required,
providing gap for welding.
Note: Rail drilling and cutting to be paid separately.
061031 For Through Rail Renewal work

Details of cost for 520 TM in one day
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,373.50
15,092.18

Code (Rs.) (Rs.)
15,243.10
17,384.75
19,992.46
Cost for 520 TRM 20,192.39
Cost for 1 TRM TRM 38.83
061032 For Casual/Scattered Rail Renewal work

Details of cost for 350 Running Metre in one day
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 38.00 38.00
7,884.50
8,278.73
8,361.51
9,536.30
10,966.75
Rate per Running Metre RM 31.65
062000 2. Sleepers
062010 Through Sleeper Renewal (TSR) with normal PSC sleepers involving removal
existing sleepers of any type along with fittings from track, insertion of PSC sleepers
lying along the cess / formation / slope / toe within 5 metres height with all fittings to
specified spacing, gauge and squareness, one round of thorough packing to make
track fit for 20 kmph speed, dressing of ballast to standard profile, all in accordance
with the latest provisions of IRPWM and stacking of all released material neatly at
specified places as directed by Engineer in-charge.
062011 For location of work not involving deep screening

Details of cost for 80 sleepers considering one group of 2 persons will remove 10
sleepers in a day after making space for removal and another group of 2 persons will
insert 16 sleepers in a day.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For removing sleeper & fittings
(ii) For insertion of sleepers, squaring, greasing of fittings, fixing etc.
(iii) For one round packing & dressing (13 Sleeper/man)
(iv) For stacking of released materials
T&P Lumpsum 9901 1.00 80.00 80.00
17,067.00

Code (Rs.) (Rs.)
17,237.67
19,659.56
22,608.50
Cost for 80 sleepers 22,834.58
Rate of each sleeper Each 285.43
062012 For location of work involving deep screening (deep screening to be paid separately).
Details of cost for 80 sleepers
Deep screening involve complete removal of ballast making free space for removal
and innsertion and initial packing is a part of deep screening, TSR will involve only
insertion and removal without obstruction sleepers. Therefore, one group of 2 persons
will remove 20 sleepers in a day and another group of 2 persons will insert 16
sleepers in a day.
Labour:
(ii) For inserting sleeper with fixing fittings etc.
(iii) For stacking of released materials
Misc.:
T&P Lumpsum 9901 1.00 30.00 30.00
9,512.00
9,607.12
10,956.92
12,600.46
062013 For PSC wider base sleepers - For location of work not involving deep screening
Considering 2.5% extra over 062011, Cost of Each sleeper
Rate of each sleeper Each 062011 285.43 1.03 292.57
062014 For PSC wider base sleepers - For location of work involving deep screening. (deep
screening to be paid separately)
Considering 2.5% Extra over item No 062012, Cost of Each sleeper
Rate of each sleeper Each 062012 159.08 1.03 163.06
062015 Extra to item no. 062011, 062012, 062013 and 062014 for sleepers lying on slope /
toe of bank beyond initial height of 5 metres.
Labour:
1,724.00
1,741.24
1,985.88
2,283.77

Code (Rs.) (Rs.)
062020 Re-spacing of existing PSC sleepers for Increasing Sleeper Density (ISD) work in
track after marking of sleeper spacing as per required sleeper density, including
fixing all fastenings and initial packing, as directed.
Note: Insertion of new sleeper will be paid extra under relevant item.
062021 For location of work not involving deep screening

Detail of cost for 192 TM (1 person will do re-spacing of 10 sleepers of 1660 density
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Pre marking of sleeper spacing as per required density
(ii) Re spacing of sleepers with fixing fittings
(iii) For initial packing
Misc.:
T & P and consumables Lumpsum 9901 1.00 100.00 100.00
20,077.75
20,278.53
23,127.66
26,596.81
Cost for 192 TRM 26,862.78
Rate of 1 TRM TRM 139.91
062022 For location of work involving deep screening (deep screening to be paid separately).
Considering cost for 240 TM (For 1660 density, 240 TM = 400 Sleepers)
Group of additional 4 persons will do re-spacing of 80 sleepers. Additional labour
required for 400 sleepers = 4 x 400/80 = 20 nos.
Labour:
(i) Pre marking of sleeper spacing as per required density
(ii) Re spacing of sleepers with fixing fittings
Misc.:
9,124.75
9,216.00
10,510.85
12,087.47
Cost for 240 TM 12,208.35
Cost for 1 TM TRM 50.87
062030 Replacement of any type of sleepers in track with PSC sleepers lying on cess or at
Bridge Approaches for casual renewal at isolated locations with all fittings complete to
specified gauge & cross level with contractor’s tools including packing and dressing of
ballast, as directed by Engineer in-charge. Released materials shall be neatly stacked
and handed over at specified location or near either side of Bridge approaches as
directed.

Code (Rs.) (Rs.)
062031 Locations other than Ballasted Deck Bridge
Details of cost for 40 sleepers (one group of 4 persons will replace 8 sleepers in a
dLabour:
)
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For replacement of sleeper including fixing fastenings,packing,dressing etc.
(ii) For carting of new sleepers and carting & stacking of released materials.
Misc.:
T & P (Rail tounge, Crow bar, beater, hammer, wire claws, Rake ballast etc.) Lumpsum 9901 1.00 48.00 48.00
11,863.00
11,981.63
13,665.05
15,714.81
Rate per sleeper Each 396.80
062032 Ballasted Deck Bridge

Details of cost for 40 sleepers (one group of 5 persons will replace 8 sleepers in a
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For replacement of sleeper including fixing fastenings, packing,dressing etc.
(ii) For carting new and released sleepers from bridge approaches and stacking
sleepers
Misc.:
T & P (Rail tounge, Crow bar, beater, hammer, wire claws, Rake ballast etc.) Lumpsum 9901 1.00 40.00 40.00
14,010.00
14,150.10
16,138.19
18,558.92
Cost for per sleeper Each 468.61
063000 3. Fittings/Lubrication Works

063010 Fixing of fish plates with fish bolts on a joint of all rail sections duly lubricating fish
plates/bolts with contractor grease graphite in running track condition including
transportation of fish plates and fish bolts from nearest station / store / level crossing.
Note: Rail cutting & drilling to be paid separately.
063011 Fish plates with 4 fish bolts.

Details of cost for 24 Joints
Labour:
(i) Leading fish plate & nut bolts from Store to site
(ii) Fixing fish plate etc.

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,722.00
2,749.22
3,135.49
3,605.81
Cost for 24 Joints 3,641.87
Rate per Joint Joint 151.74
063012 Fish plates of 6 bolts.

Details of extra cost for 24 Joints for 6 bolt holes over 4 bolt holes
Labour:
(i) Leading fish plate & nut bolts from Store to site
(ii) Fixing fish plate etc.
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
935.00
944.35
1,077.03
1,238.59
Extra cost for 24 Joints over 4 bolt holes 1,250.97
Extra cost for 1 Joints over 4 bolt holes 52.12
Cost for 1 Joint for 4 bolt holes as per item no. 063011 063011 151.74 1.00 151.74
063020 Through renewal of Metal / GFN liners in running track condition after cleaning of rail
foot at liner seat, greasing of liner and liner seat at rail foot including removing,
cleaning & lubrication of ER Clip & Insert Eye and re-driving the same with
contractor's grease graphite of approved quality with all lead & lift.
Details of cost for 1660 nos. sleeper (For renewal Metal / GFN liners one group of 2
persons will renew liners of 300 sleepers in a day)
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) For Leading & distibution of materials in 1 Km stretch & collection of released
materials.

Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
(ii) For renewal liners after cleaning rail seat and greasing of liner new liner, rail foot at
Misc.:
T & P ( Hammer, Crow bars, Tami bar, beater, Wire claws, etc.) Lumpsum 9901 1.00 48.00 48.00
Hire charges for tractor with trolley Day 0081 1200.00 1.00 1,200.00
29,877.00
30,175.77
34,415.47
39,577.79
Cost for 1660 nos.sleeper 39,973.56
Rate per Sleeper Sleeper 24.08
063030 Through Fitting Renewal (TFR) on PSC track, comprising of renewal of Grooved
Rubber Pads, Liners and ERCs without damaging PSC sleepers. Scope includes
removal of all fittings, cleaning of rail seat, rail flange at liner seats, and eye of Inserts
with wire brushes and applying Grease Graphite Grade "O" (IS:408) to eye of insert
and central leg of ERC with contractor's grease of Railway’s specification, fixing all
fitings in correct position and sealing liner edges with grease all complete including
collection and stacking of released materials at nominated locations within SSE
Jurisdiction as directed by Engineer-in-Charge.
Note: All the fittings will be supplied at SSE/Stores/Depot.
Details of cost for 1660 nos. sleeper (For TFR on PSC track one group of 3 persons
will renew fittings for 185 sleepers in a day).
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour:
(ii) For Fitting renewal & greasing of ERC's, liners & sealing liner edges.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
37,236.00
37,608.36
42,892.33
49,326.18
Cost for 1660 nos. sleeper 49,819.45

Code (Rs.) (Rs.)
063040 Through replacement of Grooved Rubber Sole pads(GRSP) on PSC sleepers duly
removing the ERCs and liners and replacing the GRSP by just lifting the rail after
cleaning the rail seat, refixing the liner and ERC after lubrication of ERCs, liners and
Liner contact area with Contractor's Grease Graphite Grade 'O' (IS:408) duly
cleaning of rust/scale of ERC, Metal /GFN liners & SGCI insert by using wire brush,
scrapper/sand emery paper etc., with all contractor’s labour, tools, plants including
collection and stacking of released materials at nominated locations within SSE
Jurisdiction and as directed by Engineer-in-Charge.
Note: GRSP will be supplied at SSE/stores/depot.
Details of cost for 1660 nos. sleeper (For Through replacement of GRSP one group
of 3 persons will renew GRSP for 200 sleepers in a day).
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour:
(ii) For GRSP renewal & greasing of ERC's, liners & sealing liner edges.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
34,650.00
34,996.50
39,913.51
45,900.53
Cost for 1660 nos. sleeper 46,359.54
063050 Lubrication of fish plated rail joints under traffic by using Grease Graphite Grade 'O'
(IS:408) and Black oil, tools & plants, supplied by contractor for all types of rail
sections as per procedure laid down in latest version of IRPWM and as directed by
Engineer In charge.
Note: Release U/S bolt & nuts is to be deposited back. If any fish bolts is jammed it
should be cut with chisel and hammer and replaced with fresh fish bolt supplied.
063051 For 1.00m long fishplates

Details of cost for 200 nos.joints ( One group of 1 B.smith + 1 Helper + 9 Persons will
do 100 joints in a day )
Material:
For greasing of 1 Fish plated joint required 100 gram grease graphite.
Cotton Jute Kg 0494 40.00 4.00 160.00
Black Oil (used lubricating oil) Litre 0475 15.00 5.00 75.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T & P (Spanner, Crow bars, beater, Wire claws, Hammer, magnifying glass, mirror Lumpsum 9901 1.00 44.00 44.00
16,566.00
16,731.66
19,082.46
21,944.83
Cost for 200 joints 22,164.28
063052 For 610 mm long fish plates.

Details of cost for 300 nos.joints ( One group of 1 B.smith + 1 Helper + 9 Persons will
do 150 joints in a day )
Material:
For greasing of 1 Fish plated joint required 80 gram grease graphite.
Cotton Jute Kg 0494 40.00 4.00 160.00
Labour: 0.00
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Spanner, Crow bars, beater, Wire claws, Hammer, magnifying glass, mirror Lumpsum 9901 1.00 40.00 40.00
17,507.00
17,682.07
20,166.40
23,191.36
063060 Opening and refixing of Joggled fish plates provided to weld joints/rail of any rail
section under traffic to enable examination of weld/rail by departmental official
nominated by Engineer Incharge and lubrication of fishplates by applying
departmental Grease graphite grade 'O' (IS:408) to fishing planes and bolts by
departmental black oil as per procedure laid down in latest version of IRPWM,
including all tools required and as directed by Engineer-in-charge.
Note:
1. Grease Graphite, black oil, fish bolts, K.Oil, wire brush, required for work shall be
given by department and issued at concerned SSE/PW Stores.
2.Jammed fish bolts shall be cut using chisel and hammer and replaced with new
Details of cost for 40 sets considering 1 group of 3 persons shall do 40 Sets
Labour:
Misc.: 0.00
T & P (Spanner set, Chisel, Hammer, Beater etc.) Lumpsum 9901 1.00 20.00 20.00
1,313.00

Code (Rs.) (Rs.)
1,326.13
1,512.45
1,739.32
Cost for 40 Sets 1,756.71
Rate per Set Set 43.92
063070 Lubrication of Elastic Rail Clips on PSC sleepers with contractor’s grease, conforming
to Railway’s specifications, labour etc. complete as per procedure prescribed in
latest edition of IRPWM.
Details of cost for 6640 nos. ERC (For Lubrication of ERC's one group of 2 persons
will do 1200 ERC's in a day)
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
16,853.00
17,021.53
19,413.05
22,325.01
Cost for 6640 nos. ERC 22,548.26
Rate per ERC Each 3.40
063080 Lubrication of Elastic Rail Clips on PSC sleepers with Railway’s grease, conforming
to Railway’s specifications, labour etc. complete as per procedure prescribed in latest
edition of IRPWM.
Details of cost for 6640 nos. ERC (For Lubrication of ERC's one group of 2 persons
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 10.00 50.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
7,253.00
7,325.53
8,354.77

Code (Rs.) (Rs.)
9,607.98
Cost for 6640 nos. ERC 9,704.06
063090 Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN
liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert
by using wire brush, scrapper / sand emery paper etc supply and application of
graphite grease, as prescribed by Railway for under side of liners & corresponding
area of rail foot & SGCI insert with ERCs and re-fixing the same as per procedure
prescribed in latest edition of IRPWM with contractors grease and all other tools &
plants complete and as directed.
Details of cost for 1660 sleepers i..e. 6640 nos. ERC (For Lubrication of ERC with
liner contact area one group of 5 persons will do 1000 ERC's in a day)
Material:
For greasing of ERCs and liner contact area of 1 sleeper requires 35 gram grease
graphite.
Sand Paper Nos. 0496 5.00 10.00 50.00
Cotton Jute Kg 0494 40.00 4.00 160.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
29,701.00
29,998.01
34,212.73
39,344.64
Cost for 1660 Sleepers 39,738.09
Rate per sleeper Sleeper 23.94
063100 Removing seized ERC from SGCI inserts of existing track by using suitable approved
chemicals or by using heavy duty extractoror or by using any approved method and
re-fixing it with lubrication of insert eye and ERC as per provisions of IRPWM, as
directed by engineer in-charge
Note:
1.Due care shall be taken to avoid any damage to the sleeper
2.A penality of 50% of the basic cost of new sleeper in nearest sleeper factory shall
be levied on each, if SGCI inseret is broken or sleeper gets cracked in the process.
Details of cost for 100 Nos. ERC

Material:
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 5.00 25.00
Grease Graphite Grade 'O' (IS:408) Kg 0184 240.00 1.00 240.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
Hire charges of Heavy Duty Hydraulic Extractor (10 Tonnes) Day 0145 200.00 1.00 200.00
3,260.00
3,292.60
3,755.21
4,318.49
Cost for 100 Nos. ERC 4,361.68
063110 Lubrication of gauge face of rail on curves, cross overs, points & crossings,turn-in
curves and at locations as required with contractor's grease graphite grade "O" IS 408
and as directed.
Material:
Cotton Jute Kg 0494 40.00 0.25 10.00
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,880.25
3,919.05
4,469.68
5,140.13
Cost for 1000 RM 5,191.53
Rate per RM RM 5.19
063120 Lubrication of Plate/Rail screws of Points and crossings, SEJs, Bridges, Curves etc,
including removal of screws carefully without damaging sleepers cleaning with wire
brush etc both screws and dowel hole applying Railways grease graphite, refixing the
screw and sealing the top and sides of screw with Railway's grease graphite to
prevent ingress of moisture and corrosion with contractors labour, tools, consumables
under traffic condition all lead and lift complete.
063121 By using Railway's Grease graphite

Details of Cost for 200 Screws
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P (Crow bar,Hammer,Box Spanner,Wire brush etc,) Lumpsum 9901 1.00 50.00 50.00
3,928.00

Code (Rs.) (Rs.)
3,967.28

Code (Rs.) (Rs.)
4,524.68
5,203.39
Cost for 200 Screws 5,255.42
Rate per screw Each 26.28
063122 By using Contractor's Grease Graphite

Details of Cost for 200 Screws
Material:
Man Power
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc
T&P (Crow bar,Hammer,Box Spanner,Wire brush,etc,) Lumpsum 9901 1.00 60.00 60.00
5,153.00
5,204.53
5,935.77
6,826.13
Cost for 200 Screws 6,894.39
Rate per screw Each 34.47
063130 Scattered renewal or replacement of missing / worn-out fittings with Railway's fittings
for track/Points & Crossings sleepers including leading to required location for the
work and the released fittings shall be collected and neatly stacked, as directed by
the Engineer Incharge.
063131 GRSP
Details of cost for 200 nos
Labour:
Misc.:
T & P ( Hammer, Crow bars, Tami bar, beater, etc.) Lumpsum 9901 1.00 10.00 10.00
2,596.00
2,621.96
2,990.35
3,438.90
Cost for 200 nos 3,473.29
Rate per GRSP Each 17.37
063132 ERCS/Metal/GFN Liners

Details of cost for 500 nos
Labour:

Code (Rs.) (Rs.)
Misc.:
2,596.00
2,621.96
2,990.35
3,438.90
063140 Renewal of seized/corroded Plate/Rail screws on PSC Sleepers by using gas or any
approved methods, duly drilling holes in broken screw and removing existing screw
pieces from the holes alongwith existing dowels and fixing new contractor's dowels
(procured from RDSO approved sources) and grouting around dowel with Epoxy
materials and refixing new Railway's rail/Plate screws duly greasing the screw with
specified grease with all contractor's materials, consumables, tools & plants, labour
with all lead, lif
Note:
1.Due care shall be taken to avoid any damage to the sleeper
2.A penality of 10% of the basic cost of new sleeper in nearest sleeper factory shall
be levied on each, if sleeper gets damaged in the process.
Detail of cost for 60 holes

Material:
Epoxy for fixing HDPE dowel, Rubber Pads as per RDSO approved specification Kg 0321 500.00 5.00 2,500.00
HDPE Dowels Each 0456 100.00 60.00 6,000.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
12,406.26
12,530.32
14,290.83
16,434.46
Cost for 60 holes 16,598.80
Rate per hole Each 276.65
064000 4. Drilling and Cutting Works

064010 Cutting / cropping of rail of 52Kg – 72 UTS or lighter section, manually and perfectly
vertical with contractor’s labour, hacksaw blade and tools & plants.
Note:
1.Manual cutting should be used only in emergencies with prior permission of
sectional ADEN where machine cutting can not be arranged in time.
2.Cutting of Rails with blade and forcing to part by using other means to break the
rails is prohibited.
3.Rails should be cut right through hacksaw blades only.
064011 On Cess
Details of cost for 15 cuts in a day
Material:

Code (Rs.) (Rs.)
High Speed Hacksaw Blade of size 300mm x 12.5mm x 0.63mm (18TPI) as per as Nos. 0457 160.00 2.00 320.00
per RDSO's Spec. no. TM/SM/26 (latest Rev.)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,090.50
2,111.41
2,408.06
2,769.27
Cost for 15 cuts 2,796.96
Rate per cut Each 186.46
064012 In-situ situation

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,521.50
2,546.72
2,904.53
3,340.21
064020 Cutting / cropping of rail of 52Kg – 90 UTS, manually and perfectly vertical with
contractor’s labour, hacksaw blade and tools & plants -
Note:
2. Cutting of Rails with blade and forcing to part by using other means to break the
064021 On Cess
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00

Code (Rs.) (Rs.)
2,090.50
2,111.41
2,408.06
2,769.27

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,521.50
2,546.72
2,904.53
3,340.21
064030 Cutting / cropping of rail of 60Kg – 90 UTS, manually and perfectly vertical with
contractor’s labour, hacksaw blade and tools & plants -
Note:
2. Cutting of Rails with blade and forcing to part by using other means to break the
064031 On Cess
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,090.50
2,111.41
2,408.06
2,769.27

Code (Rs.) (Rs.)

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,441.50
2,465.92
2,812.38
3,234.23
064033 Extra to item no. 064031 for cutting 110 UTS rail
Take 15% of relevant item rate
Extra Rate per cut Each 41.95
064034 Extra to item no. 064032 for cutting 110 UTS rail
Take 15 % of relevant item rate
Extra Rate per cut Each 61.25
064040 Drilling of hole of different diameter and chamfering, in rail of any section and any
UTS manually only in emergencies only with contractor's labours, tools & plants,
consumables etc.
064041 Hole of dia. 26.5mm and above
Details of cost for 15 holes in a day
Material:
Drill twist made of high speed steel for size 26.5mm dia of Addison / I T make Each 0466 2852.30 0.50 1,426.15
Labour:
Misc.:
T & P (Ratchet & Chamfering kit etc.) Lumpsum 9901 1.00 10.00 10.00
2,981.15
3,010.96
3,434.00
3,949.10
Cost for 15 Holes 3,988.59
Rate per Hole Each 265.91
064042 Hole of dia. below 26.5mm

Details of cost for 20 holes in a day
Material:
Drill twist made of high speed steel for size 18mm dia of Addison / I T make Each 0467 1866.40 0.50 933.20

Code (Rs.) (Rs.)
Labour:

Code (Rs.) (Rs.)
Misc.:
T & P (Ratchet & Champhering kit etc.) Lumpsum 9901 1.00 10.00 10.00
2,488.20
2,513.08
2,866.17
3,296.10
Cost for 20 Holes 3,329.06
Rate per Hole Each 166.45
064050 Gas cutting of rail of various sections with contractor’s tools & plants, as directed by
engineer in-charge :
064051 Rail section of 90R and below
Details of cost for 60 Cut
Material:
Labour:
Misc.:
T & P (Gas Cutting equipments) Lumpsum 9901 1.00 20.00 20.00
4,085.68
4,126.54
4,706.32
5,412.26
Cost for 60 Cut 5,466.39
Rate per Cut Each 91.11
064052 Rail section of 52Kg and above

Details of cost for 50 Cut
Material:
Labour:
Misc.:
T & P (Gas Cutting equipments) Lumpsum 9901 1.00 20.00 20.00
4,085.68
4,126.54
4,706.32
5,412.26
Cost for 50 Cut 5,466.39
Rate per Cut Each 109.33

Code (Rs.) (Rs.)
065000 5.Switch Expansion Joints (SEJs)
065010 Renewal of existing SEJ with IRS Switch Expansion Joint (SEJ) with PSC sleepers
under traffic block conditions as per approved drawing including fixing of special size
bearing plate, rubber pad and other sleeper / rail fittings, greasing to the fittings,
leading all new materials to site, transportation of released materials within a lead of
250m, cutting of Rails, drilling of holes, fixing of related fittings, providing temporary
connection with fishplates till welding of SEJ is done and sleepers shall be given initial
packing to make track fit for 20KMPH speed.
Note:
(1) Rail cutting and hole dilling shall be paid seperately.
(2) One set comprise complete SEJ on both rails at SEJ.
Details of cost for 2 sets

Material:
Labour:
(i) Leading of all fitting, fish plate, nut & bolt and SEJ rail, sleeper fitting etc. alongwith
(ii) Assembling and Insertion in track SEJ with sleepers by removing the existing
(iii) Fixing of fish plate with nut & bolt and packing of SEJ, aligning, levelling etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Spanner, Hammer, beater, Rail tongue etc.) Lumpsum 9901 1.00 32.00 32.00
9,131.00
10,044.10
10,144.54
11,569.85
13,305.33
Cost for 2 sets 13,438.38
Rate per set Set 6,719.19
065020 Renewal of existing SEJ with improved SEJ with PSC sleepers under traffic block
conditions as per approved drawing including fixing of special size bearing plate,
rubber pad and other sleeper / rail fittings, greasing to the fittings,leading
rails,sleepers & fittings to site, leading and stacking of released materials within a
lead of 250m, cutting of Rails,drilling of holes,fixing of related fittings, providing
temporary connection with fishplates till welding of SEJ is done and sleepers shall be
given initial packing to make track fit for 20KMPH speed.
Note:

Material:
Labour:
(i) Leading of all fitting, fish plate, nut & bolt and SEJ rail, sleeper fitting etc. alongwith

Code (Rs.) (Rs.)
(ii) Assembling and Insertion in track SEJ with sleepers by removing the existing
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
10,009.00
11,009.90
11,120.00
12,682.36
14,584.71
065030 Assembling and Laying of Improved Switch Expansion Joint (SEJ) on PSC sleepers
of any rail section as per RDSO drawing including leading of SEJ rails, sleepers,
fittings for a free lead of 250 metres, cutting of rails,drilling of holes as required and
lubrication of SEJ, gauging, aligning rails, providing temporary connection with
adequate welding gap with adjoining rails,providing reference posts at SEJ, first
through packing of SEJ potion to make track geometry fit for 30 kmph speed and
making ballast profile as per IRPWM.
Note:
065031 Under Conditions not requiring Traffic Block

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Leading of all fitting, fish plate, nut & bolt and SEJ rail, sleeper fitting etc.
(ii) Assembling and Insertion in track SEJ with sleepers
Misc.: 0.00
T & P (Crow bar, tami bar, beater, hammer, Rail dolly, Spanner, Rail tounge etc.) Lumpsum 9901 1.00 32.00 32.00
8,700.00
8,787.00
10,021.57
11,524.81

Code (Rs.) (Rs.)
065032 Under Traffic Block Conditions

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Leading of all fitting, fish plate, nut & bolt and SEJ rail, sleeper fitting etc.
(ii) Assembling and Insertion in track SEJ with sleepers
Misc.:
8,700.00
9,570.00
9,665.70
11,023.73
12,677.29
065040 Dismantling & removing existing SEJ (Switch Expansion Joint) assembly during line
block and its replacement with plain track as of adjoining section with all fittings
including rail cutting and drilling of holes and renewal of special sleepers with PSC
Sleepers as directed and aligning rails, providing fishplates and bolts/ temporary
connection with adequate welding gap with adjoining rail and ensuring proper track
geometry for 30 kmph speed.The release material shall be stacked as directed by
Engineer incharge.
Details of cost for 2 set

Material:
Normal unleaded Petrol Litre 0182 105.00 0.50 52.50
Labour:
(i) Cutting SEJ, Drilling rails &.removing SEJ etc.
(ii) Fixing required length of same rail section and fixing fish plate & nut bolt etc.
(iii) Sleeper insertion against SEJ sleeper through packing, aligning, fixing fitting &
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:

Code (Rs.) (Rs.)
Hire charges of Rail Cutting Machine Day 0142 300.00 0.50 150.00
10,733.65
11,807.02
11,925.09
13,600.56
15,640.64
Cost for 2 set 15,797.05
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 7: Turnouts and Renewals
CHAPTER - 7 : Turnouts and Renewals

Code (Rs.) (Rs.)
071000 1. Dismantling Works
071010 Dismantling of existing BG turnouts, diamond crossings and derailing switches with all
types of rails and sleeper layout, removing rails, switches, crossings, sleepers &
fastenings, leveling of ballast to correct profile & stacking all the released materials,
sleepers, fastenings, rails, switches & crossings including segregating & stacking at
specified locations in a neat and countable manner, within the lead of 250m & all lift,
clear of infringements, crossing of track, if any complete, as directed, Under Traffic
Block Conditions.
Note:
1. This item shall be operated only when existing turnout is replaced either with new
turnout in case of TTR or with plain track when existing turnout is no more required at
that location.
2. Rail cutting will be paid extra under relevant item.
3. Laying of new turnout or plain track shall be paid under relavent item for laying on
already prepared ballst bed with initial packing to make it fit for 20 kmph.
071011 1 in 8½ Turnout
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Removing Lead Rails, Switches, Crossing, Fittings and stacking etc.
(ii) Removing Sleepers, Transporting & Stacking at store.
(iii) Levelling of ballast
(iv) Stacking rails, switches, crossing etc.
Misc.:
T & P (Crow bar, tami bar, beater, Rake ballast , hammer etc.) Lumpsum 9901 1.00 92.00 92.00
17,669.00
19,435.90
19,630.26
22,388.31
25,746.56
071012 1 in 12 Turnout
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
20,267.00
22,293.70
22,516.64
25,680.22
29,532.26
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
22,869.00
25,155.90
25,407.46
28,977.21
33,323.79
Cost for 1 set Set 33,657.03
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Removing Lead Rails, Switches, Fittings and stackingetc.

Code (Rs.) (Rs.)
Misc.:
25,471.00
28,018.10
28,298.28
32,274.19
37,115.32
071015 Diamond Crossing

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Removing Lead Rails, Switches, Fittings and stacking etc.
Misc.:
27,203.00
29,923.30
30,222.53
34,468.80
39,639.12
071020 Dismantling of existing BG turnouts, diamond crossings and derailing switches with all
types of rails and sleeper layout, removing rails, switches, crossings, sleepers &
fastenings, leveling of ballast to correct profile & stacking all the released materials,
sleepers, fastenings, rails, switches & crossings including segregating & stacking at
specified locations in a neat and countable manner, within the lead of 250m & all lift,
clear of infringements, crossing of track, if any complete, as directed, under conditions
not requiring Traffic Block.
Note:
1. This item shall be operated only when existing turnout is replaced either with new
turnout in case of TTR or with plain track when existing turnout is no more required at
that location.
2. Rail cutting will be paid extra under relevant item.
3. Laying of new turnout or plain track shall be paid under relavent item for laying on
already prepared ballst bed with initial packing to make it fit for 20 kmph.

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Misc.:
15,502.00
15,657.02
17,856.83
20,535.36
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Misc.:
16,803.00
16,971.03
19,355.46
22,258.78
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
18,970.00
19,159.70
21,851.64
25,129.38
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
21,137.00
21,348.37
24,347.82
27,999.99

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:

Code (Rs.) (Rs.)
26,585.00
26,850.85
30,623.39
35,216.90
071026 Derailing Switch

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
Hire charges for tractor with trolley Day 0081 1200.00 0.50 600.00
7,092.00
7,162.92
8,169.31
9,394.71
071030 Dismantling the existing BG Buffer-stop laid with rails & wooden/ST sleepers including
leading the dismantled Bufferstop materials to nominated places within station yard
limits and stacking as material-wise and classification-wise duly releasing all fittings
carefully without causing any damage with all contractor's labour, tools, with all lead
and lifts, crossing of tracks if any, etc., complete as directed by the Engineer-in-charge.

Labour:
(i)Stacking rails, and fittings etc.
Misc.:
11,459.00
11,573.59
13,199.68

Code (Rs.) (Rs.)
15,179.63
072000 2. Assembling, Insertion and laying Works

072010 Assembling complete BG Turnout on staging to correct gauge and alignment as per
standard drawing on all types of rails over PSC sleepers at specified locations, duly
leading special size sleepers, switches, crossings, fittings, fastenings etc. as per
approved drawing with maximum lead of 500m & all lift and testing points with S&T
staff for throw of switch etc. at station yard after levelling surface complete and as
directed by engineer in-charge clear of infringements, crossing of track, if any
complete, as directed.
Note:
1.Rail cutting and Drilling shall be paid separately
2. Required P.Way fittings will be supplied at the SSE/P.Way stores
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Leading of special size PSC sleepers, switches, crossing, fitting, fastenings etc.

(ii) Preparing stage for putting new PSC sleepers, Switches, Lead rails, crossings etc.

(iii) Fixing fitting & linking of switch, lead, crossing portion etc.
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail dolly etc.) Lumpsum 9901 1.00 132.00 132.00
24,426.00
24,670.26
28,136.43
32,356.90
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00



Code (Rs.) (Rs.)

Misc.:
27,459.00
27,733.59
31,630.16
36,374.68
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Misc.:
29,626.00
29,922.26
34,126.34
39,245.29
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00


Misc.:

Code (Rs.) (Rs.)
33,096.00
33,426.96
38,123.45
43,841.97
072020 Assembling all types of Switches with 52Kg / 60Kg rails on PSC sleepers on
temporary staging, with railway's sleepers, rails etc. at indicated location as per
standard drawing duly leading sleepers, rails, switches, fastenings etc. with lead and
lift including cutting, drilling, fixing of all components, fittings etc. with housing of
tongue rails as per requirement of signaling etc. etc. complete as directed by engineer
in-charge.
Note:
Required P.way fittings shall be supplied at SSE/P.Way stores.
072021 1 in 8½ Turnouts
Material:
High Speed Hacksaw Blade of size 300mm x 12.5mm x 0.63mm (18TPI) as per as per Nos. 0457 160.00 0.50 80.00
Labour:
(i)preparation of staging,leading rails,sleepers and fittings and assembling of switch
including rail cuting and hole drilling
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Crow bar, Spanner, Hammer, Rail tounge, Pan iron mortar etc.) Lumpsum 9901 1.00 76.00 76.00
11,710.15
11,827.25
13,488.98
15,512.33
072022 1 in 12 Turnouts
Material:

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
13,446.15
13,580.61
15,488.69
17,811.99
Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,620.65
14,766.86
16,841.60
19,367.84
Material:

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
15,490.65
15,645.56
17,843.76
20,520.32

Material:
Drill twist made of high speed steel for size 26.5mm dia of Addison / I T make Each 0466 2852.30 0.25 713.08
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
10,854.58
10,963.12
12,503.44
14,378.96

Code (Rs.) (Rs.)
072030 Assembling on temporary staging and insertion of all types of turnouts on prepared
ballast bed during traffic block, manually or by contractor's cranes, at specified location
including diamond crossings with 52Kg / 60Kg rail section on PSC sleepers with
Railways rails/sleepers available anywhere within 250m as per standard drawing,
duly leading sleepers, rails, switches, crossings, fastenings etc. including rail cutting,
drilling, fixing of all components, fittings etc. with housing of tongue rails as per
requirement of signaling etc. including preparation for operation of traffic block,
including crossing of track, filling and spreading of ballast in crib and shoulder as
required, linking of turnout with existing track, attending track parameters including
lifting, providing one round of packing to make track fit for 20 kmph speed etc.
complete as directed by engineer in-charge.
Note: Required P.Way fittings shall be supplied at the SSE/P.Way stores.
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Leading of sleepers,switches,rails,crossings and fittings
(ii) Preparing stage for assembling turnout
(iii) Linking of switch,lead and crossing portion on stage
(iv) Filling of ballast in crib and shoulder portion
(v) Insertion of assembled Turnout
(vi) Linking of Track and initial packing
Misc.:
36,127.30
37,933.67
38,313.00
43,695.98
50,250.38
Material:

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Leading of sleepers, switches, rails, crossings and fittings
(iii) Linking of switch, lead and crossing portion on stage
Misc.:
41,834.55
43,926.28
44,365.54
50,598.90
58,188.73
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00

Code (Rs.) (Rs.)
Misc.:
46,585.88
48,915.17
49,404.32
56,345.63
64,797.47
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
51,743.20
54,330.36
54,873.66

Code (Rs.) (Rs.)
62,583.41
71,970.93

Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Leading of sleepers,rails,crossings and fittings
(ii) Preparing stage for assembling diamond
(iii) Linking of diamond on stage
(v) Insertion of Diamond
Misc.:
53,923.20
56,619.36
57,185.55
65,220.12
75,003.14

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
17,712.33
18,597.94
18,783.92
21,423.06
24,636.52
072040 Laying and linking of turnouts of all types including diamond crossings & Derailing
switches with 52Kg / 60Kg rail section on PSC sleepers on prepared ballast bed for
New lines or during total closure of section at indicated location as per standard
drawing, duly leading sleepers, rails, switches, crossings, fastenings including rail
cutting, drilling, fixing of all components, fittings with housing of tongue rails as per
requirement of signalin, preparing ballast bed, filling and spreading of ballast as
required, linking of turnout with track, attending track parameters including lifting,
providing one round of packing to make track fit for 20 kmph speed complete as
directed by engineer in-charge.
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(ii) Linking of switch, lead and crossing portion on stage

Code (Rs.) (Rs.)
(iii) Filling ballast in crib and shoulder for initial packing
(iv) Linking of Track and initial packing
Misc :
28,238.30
28,520.68
32,527.84
37,407.01
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(ii) Linking of switch,lead and crossing portion on stage
Misc.:
32,783.55
33,111.39
37,763.54
43,428.07
Material:

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Leading of sleepers, switches, rails,crossings and fittings
(ii) Linking of switch, lead and crossing portion on stage
Misc.:
35,810.88
36,168.98
41,250.73
47,438.33
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
39,244.20

Code (Rs.) (Rs.)
39,636.64
45,205.59
51,986.43

Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
40,993.20
41,403.13
47,220.27
54,303.31

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
12,540.33
12,665.73
14,445.26
16,612.05
072050 Laying and linking of turnouts of all types including diamond crossings & Derailing
switches with 52Kg / 60Kg rail section on PSC sleepers on ballast bed prepared after
dismantling & removal of existing turnout/normal line during TTR/yard remodelling
under traffic block, as per standard drawing, duly leading sleepers, rails, switches,
crossings, fastenings including rail cutting, drilling, fixing of all components, fittings
with housing of tongue rails as per requirement of signalin, preparing ballast bed, filling
and spreading of ballast as required, linking of turnout with track, attending track
parameters including lifting, providing one round of packing to make track fit for 20
kmph speed complete as directed by engineer in-charge.
Note: Removal of existing turnout/normal line, lavelling ballast bed for laying
transportation of released material and stacking shall be paid extra under relevant
sum.
Considering 10% additional for working under block over similar items where there is
no need of traffic block
Rate per set Set 072041 37781.08 1.10 41,559.19
Rate per set Set 072042 43862.35 1.10 48,248.58
Rate per set Set 072043 47912.72 1.10 52,703.99
Rate per set Set 072044 52506.29 1.10 57,756.92

Rate per set Set 072045 54846.35 1.10 60,330.98

Code (Rs.) (Rs.)
Rate per set Set 072046 8389.09 1.10 9,228.00
072060 Assembling on temporary staging and insertion of all types of switches including TWS
on prepared ballast bed during traffic block, manually or by contractor's cranes, at
specified location with 52Kg / 60Kg rail section on PSC sleepers with Railways
rails/sleepers available within 250m as per standard drawing, duly leading sleepers,
rails, switches, fastenings etc. including rail cutting, drilling, fixing of all components,
fittings etc. with housing of tongue rails as per requirement of signaling etc. including
preparation for operation of traffic block, including crossing of track, filling and
spreading of ballast in crib and shoulder as required, linking with existing track,
attending track parameters including lifting, providing one round of packing to make
track fit for 20 kmph speed etc. complete as directed by engineer in-charge.
Note: Required P.Way fittings shall be supplied at the SSE/P.Way stores.
Material:
Labour:
i) Leading switches, sleepers etc., assembling switches on temporary staging,
removing ballast muck upto required level, and
ii) Fixing, inserting of switch, filling ballast, levelling & packing
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
11,090.70
11,645.24
11,761.69
13,414.20
15,426.34
Material:

Code (Rs.) (Rs.)
Labour:
i) Assembling switch, removing ballast muck upto required level, and leading switches
and sleepers etc
(ii) Fixing, laying of switch, filling ballast, levelling & packing
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,550.70
15,278.24
15,431.02
17,599.08
20,238.94
Material:
Labour:
i) Assembling switch,removing ballast muck upto required level ,and leading switches
and sleepers etc
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
16,282.70
17,096.84
17,267.80
19,693.93
22,648.02

Code (Rs.) (Rs.)
Material:
Labour:
i) Assembling switch,removing ballast muck upto required level ,and leading switches
and sleepers etc
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
17,645.65
18,527.93
18,713.21
21,342.42
24,543.78
073000 3.Lifting Works

073010 Lifting for increase in ballast cushion of existing points & crossing layouts upto 75mm
or part thereof including approach and exit sleepers including one round of through
packing, adjustment to sleeper spacing, tightening of fittings, boxing of ballast and
ramping out on either side at slope not steeper than 1 in 1000 or as directed.
Note: Item will be paid only when lifting is 50mm or more.
073011 1 in 8½ Points & Crossing

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
(i) Opening ballast at packing zone lifting & packing

(ii) Adjust sleeper spacing, tightening fitting, boxing etc.
Misc.:
T & P (Crow bar, Jacks, beater, Rake ballast , Pan iron mortar etc.) Lumpsum 9901 1.00 44.00 44.00

Code (Rs.) (Rs.)
8,411.00

Code (Rs.) (Rs.)
8,495.11
9,688.67
11,141.97
073012 1 in 12 Points & Crossing

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
11,436.00
11,550.36
13,173.19
15,149.16

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
13,172.00
13,303.72
15,172.89
17,448.83

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T & P (Crow bar, Jacks, beater, Rake ballast , Pan iron mortar etc) Lumpsum 9901 1.00 76.00 76.00
15,339.00
15,492.39
17,669.07
20,319.43

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
19,657.00
19,853.57
22,643.00
26,039.45

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
4,937.00
4,986.37
5,686.95
6,540.00

Code (Rs.) (Rs.)
073017 Extra over item nos. 073011 to 073015 for additional lift beyond 75mm for every Each 0.15
50mm or part thereof upto 225mm for each set
073020 Lifting the newly inserted BG 60 Kg. / 52 Kg. turnouts/ trap switches to required level
to provide a ballast cushion upto 225mm from existing level with Railway's stone
ballast in convenient stages including one round of through packing after completion of
final stage of lift, levelling, aligning, gauging and boxing etc., with contractor's labour,
tools, with all lead and lifts etc., complete and as directed by the Engineer-in-charge.
Note:
1. The item shall be used only when UNIMAT is not available for the work before the
turnout is opened for operation.
2. Leading and dumping of ballast will be paid separately under relevant item.
073021 For 1 in 8½ Points & Crossing

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) lifting & packing,boxing
Misc.:
4,943.00
4,992.43
5,693.87
6,547.95
073022 For 1 in 12 Points & Crossing

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
6,236.00
6,298.36
7,183.28
8,260.77
073023 For 1 in 16 Points & Crossing

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
7,960.00
8,039.60
9,169.16
10,544.54
073024 For Derailing Switch

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
3,650.00
3,686.50
4,204.45
4,835.12
074000 4. Renewal Works

074010 Casual renewal of PSC sleepers on points and crossings, derailing switches and
diamonds portion of any layout, duly refixing all fittings including packing under new
sleepers. All the released materials shall be stacked at specified location in a
countable manner within the lead of 250m & all lift, clear of infringements, crossing of
track, if any complete, as directed with contractor's vehicles, consumables, stores,
labour etc. complete, as directed by engineer in-charge.
074011 Sleepers upto 2.85 m length

Details of cost for 30 nos.( One group of two persons will replace 2 sleepers in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

(ii) For stacking of released materials
Misc.:
T & P (Crow bar, beater, Rake ballast etc.) Lumpsum 9901 1.00 46.00 46.00
11,430.00
11,544.30
13,166.27
15,141.22

Code (Rs.) (Rs.)
Cost for 30 nos. 15,292.63
074012 Sleepers of length more than 2.85 m and up to 4.20 m

Details of cost for 30 nos.( One group of two persons will replace 2 sleepers in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Misc.:
15,740.00
15,897.40
18,130.98
20,850.63
21,059.14
074013 Sleepers of more than 4.20 m length

Details of cost for 30 nos.( One group of 5 persons will replace 3 sleepers in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Misc.:
24,801.00
25,049.01
28,568.40
32,853.66
Cost for 30 nos. 33,182.19
Rate per sleeper Each 1,106.07

Code (Rs.) (Rs.)
074020 Renewal of CMS Crossing of all rail sections with CMS crossing or with WCMS
crossing complete with fastenings including replacement of worn-out rubber pads,
liners and ERC, if required. All the released materials shall be stacked at specified
location in a countable manner within the lead of 500m & all lift, clear of
infringements, crossing of track, if any complete, as directed. with contractor's vehicles,
consumables, stores, labour etc. complete, as directed by engineer in-charge.
Note: Rail cutting and drilling shall be paid seperately under relavent item.
Labour:
Leading of CMS Crossing, opening of fittings, renewal of X-ing, fittings, packing etc.

Misc.:
T&P Lumpsum 9901 1.00 18.00 18.00
4,580.00
4,809.00
4,857.09
5,539.51
6,370.44
Labour:

Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
5,013.00
5,263.65
5,316.29
6,063.22
6,972.71

Code (Rs.) (Rs.)
Labour:

Misc.:
T&P Lumpsum 9901 1.00 22.00 22.00
5,446.00
5,718.30
5,775.48
6,586.94
7,574.98
Labour:

Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
5,879.00
6,172.95
6,234.68
7,110.65
8,177.25
074030 Renewal of Switch Rails (Tongue rails & Stock rails) and its fittings of all rail sections
complete with fittings, under line block conditions ensuring proper housing & changing
of stretcher bars and fittings as required,Work also includes drilling of hole if any,
required and fixing of fish plates with leading of rails.Released switch rails shall be
stacked at indicated place in a countable manner within the lead of 250m & all lift,
clear of infringements, crossing of track, if any complete, as directed. with contractor's
vehicles, consumables, stores, labour etc. complete, as directed by engineer in-
charge.
Note:
1).One set means Two Tongue rails and Two Stock rails
(2) In case when only one tongue & stock rail are replaced, only 50% of the quantity
shall be payable.
(3) If only one tongue rail is replaced, only 25% of the quantity of switch assembly
shall be payable for respective item.

Code (Rs.) (Rs.)
074031 1 in 8½ Switch Assembly
Material:
Labour:
Leading of stock & tounge rail, opening of fittings, removing rails, fixing stock & tounge
rail etc.
Misc.:
T & P (Crow bar, Spanner, Hammer, beater, Rake ballast , Rail tounge etc.) Lumpsum 9901 1.00 20.00 20.00
7,696.14
8,465.75
8,550.41
9,751.74
11,214.51
074032 1 in 12 Switch Assembly

Material:
Labour:
rail etc.
Misc.:
8,566.14
9,422.75
9,516.98
10,854.12
12,482.24

Material:

Code (Rs.) (Rs.)
Labour:
rail etc.
Misc.:
9,525.46
10,478.01
10,582.79
12,069.67
13,880.12

Material:
Labour:
rail etc.
Misc.:
10,391.46
11,430.61
11,544.91
13,166.97
15,142.02

Code (Rs.) (Rs.)
074040 Through Switches Renewals of existing curved/Thick web switches with Thick Web
Switches on 60Kg Points and crossings including approach rails as required, on PSC
sleepers, removing and re-fixing or replacing fittings, fastenings, stretcher bar, blocks
etc., with housing of tongue rails as per requirement of signaling etc. including
preparation for operation of traffic block, under line block conditions and packing of
any disturbed sleepers and boxing of ballast to profile, picking of slacks of track at
switch portion, crossing of track wherever necessary. All the released materials shall
be stacked at specified location in a countable manner within the lead of 250m & all
lift, clear of infringements, crossing of track, if any complete, as directed with
contractor's vehicles, consumables, stores, labour etc. complete, as directed by
engineer in-charge.
Note: Rail cutting and Hole Drilling shall be paid under relavent item.
074041 For 1 in 12 Turnouts

Details of Cost for 1 set
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Leading of all fitting, fish plate, nut & bolt,Switchw rails and approach rails,
alongwith transportation of released materials
(ii) Assembling and Insertion in track Switches with approach rails by removing
the existing switches and rails
Misc.:
T & P (Crow bar, tami bar, beater, Rake ballast , hammer, Auger,Spanner,Rail tongue Lumpsum 9901 1.00 50.00 50.00
etc.)
17,541.00
19,295.10
19,488.05
22,226.12
25,560.04
Rate per Set Set 25,815.64

Considering rate as 20% more than that for 1 in 12 turnout
Rate per set Set 074041 25815.64 1.20 30,978.77
074043 For 1 in 8.5 Turnouts

Considering rate as 20% less than that for 1 in 12 turnout
Rate per set Set 074041 25815.64 0.80 20,652.51
074050 Through renewal of Liners and ERCs on PSC turnouts without damaging PSC
sleepers. Scope includes removal of all ERCs and Liners, cleaning rail seat, rail
flange at liner seats, and eye of Inserts with wire brushes and applying grease to eye
of insert and central leg of ERC with contractor's grease of Railway’s specification,
fixing all fitings in correct position and sealing liner edges with grease all complete
including collection and stacking of released materials at nominated locations within
SSE Jurisdiction as directed by Engineer-in-Charge.

Code (Rs.) (Rs.)
074051 1 in 8.5 Turnouts
Details of cost for 4 set's ( In one set having 350 ERC's approximately ) 10 gram
grease required for 1 ERC, For 4 sets 4 X 350 X 10 = 14 Kg grease.
Material:
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
(i) For leading & distribution of materials & collection of released materials
(ii) For Fitting renewal & greasing of ERC's, liners & sealing liner edges.( one group of
Five persons will renew 200 rail seats / 1 T/out in a day )
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
LS for Transportation Charges Lumpsum 9901 1.00 150.00 150.00
7,534.50
7,609.85
8,679.03
9,980.88
Cost for 4 set's 10,080.69
Material:
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
four persons will renew 200 rail seats in a day )
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
9,092.50
9,183.43
10,473.70

Code (Rs.) (Rs.)
12,044.75
Material:
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
9,843.50
9,941.94
11,338.78
13,039.59
Material:
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:

Code (Rs.) (Rs.)
12,155.00
12,276.55
14,001.41
16,101.62
074060 Through fitting renewal (TFR) with new Grooved Rubber Sole pads(GRSP), Liners
and ERC or through renewal with new GRSPs using existing ERCs and liners after
cleaning and greasing on entire Turnout of PSC Fan shaped layout including
approach & exit sleepers comprising of removing & refixing or replacement of plate
screws, ERCs and liners including seized ERCs, replacing the GRSP after cleaning
rail seat, refixing slide chairs, lubrication of ERCs, applying grease to plate screws
and Liner contact area with contractor's Grease Graphite Grade 'O' (IS:408) after
cleaning of rust/scale on liner contact area etc., as per provisions of IRPWM of latest
version with all contractor’s labour, tools, plants and stacking all the releaded materials
etc .complete and as directed by Engineer in charge.
Note: GRSP will be supplied at at SSE/stores/depot.

Details of cost for 3 set's
Material:
( In one set having 480 ERC's & 180 plate screws approximately ) 15 gram grease
required for ERC & Plate screws, For 3 sets 3 X 560 X 15 = 25.20 Kg grease.

Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,256.00
14,398.56
16,421.56
18,884.79
074062 For 1 in 8.5 Turnouts

Rate per set Set 074061 6357.88 0.80 5,086.30

Code (Rs.) (Rs.)
Considering rate as 20% less than that for 1 in 12 turnout

Rate per set Set 074061 6357.88 1.20 7,629.46
074070 Through renewal of Grooved Rubber Sole pads(GRSP) on Switch portion of PSC fan
shaped layout comprising of removing & refixing Plate screws,ERCs including seized
ERCs and liners, and replacing the GRSP after cleaning rail seat,refixing Slide chairs,
liner and ERC after greasing and lubrication of ERCs,applying grease to liners and
Liner contact area with contractor's Grease Graphite Grade 'O' (IS:408) after cleaning
of rust/scale on liner contact area and on ERC, with all contractor’s labour, tools,
plants, leading of GRSP and stacking all the releaed materials etc .complete and as
directed by Engineer in charge.
074071 For 1 in 12 Turnouts (Sleeper No 1 to 25 and 5 approach sleepers)

Material:
( In one set having 50 ERC's approximately ) 10 gram grease required for 1 ERC, For
3 sets 3 X 50 X 10 = 1.5 Kg grease.
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 2.00 10.00
Labour:
(i) For leading & distribution of materials ,renewal &collection of released materials
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
3,379.70
3,413.50
3,893.09
4,477.06
074072 For 1 in 8.5 Turnouts & Derailng switches (Sleeper No 1 to 22 and 5 approach
sleepers)
Considering rate as 20% more less that for 1 in 12 turnout
Rate per set Set 074071 1507.28 0.80 1,205.82
074073 For 1 in 16 Turnouts (Sleeper No 1 to 31and 5 approach sleepers)
Rate per set Set 074071 1507.28 1.20 1,808.73


Code (Rs.) (Rs.)
074080 Through renewal of Grooved Rubber Sole pads(GRSP) on lead portion of PSC fan
shaped layout comprising of removing & refixing ERCs,Liners including seized ERCs
and replacing the GRSP after cleaning rail seat,refixing the liner and ERC after
lubrication of ERCs, liners and Liner contact area with contractor's Grease Graphite
Grade 'O' (IS:408) after cleaning of rust/scale on liner contact area and on ERC , etc.,
with all contractor’s labour, tools, plants,leading of GRSP and stacking all the releaed
materials etc .complete and as directed by Engineer in charge.
074081 For 1 in 12 Lead portion (Sleeper Nos 26 to 64 & 74 to 83 and 8 approach sleepers) :
Material:
( In one set having 400 ERC's approximately ) 10 gram grease required for 1 ERC,
For 3 sets 3 X 40 X 10 = 12 Kg grease.
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 6.00 30.00
Labour:
(i) For leading & distribution of materials & collection of released materials and renewal
of materials
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
8,865.00
8,953.65
10,211.64
11,743.38
074082 For 1 in 8.5 Turnouts (Sleeper No 23 to 42&59 to 54 and 8 approach sleepers)
Take 20% less of Relavaent item rate 074081 Set 074081 3953.61 0.80 3,162.88
074083 For 1 in 16 Turnouts (Sleeper No 32 to 76 & 87 to 101 and 8 approach sleepers)
Take 20% extra of Relavaent item rate 074081 Set 074081 3953.61 1.20 4,744.33
074090 Through renewal of Grooved Rubber Sole pads(GRSP) on Crossing portion of PSC
Sleeper turnout duly removing the Liners,ERCs including seized ERCs, and replacing
the GRSP after cleaning rail seat,refixing the liner and ERC after lubrication of ERCs,
liners and Liner contact area with contractor's Grease Graphite Grade 'O' (IS:408)
after cleaning of rust/scale on liner contact area etc., with all contractor’s labour, tools,
plants, transportation of GRSP, and stacking all the releaed materials etc. complete
and as directed by Engineer in charge.
074091 For 1 in 12 Turnouts (Sleeper No 65 to 73 )


Code (Rs.) (Rs.)
Material:
( In one set having 48 ERC's approximately ) 10 gram grease required for 1 ERC, For
3 sets 3 X 48 X 10 = 1.5 Kg grease.
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 2.00 10.00
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
2,517.70
2,542.88
2,900.15
3,335.17
074092 For 1 in 8.5 Turnouts (Sleeper No 43 to 48)
Take 20% less of Relavant item rate 074091 Set 074091 1122.84 0.80 898.27
074093 For 1 in 16 Turnouts (Sleeper No 77 to 86)
Take 20% extra of Relavant item rate 074091 Set 074091 1122.84 1.20 1,347.41
074100 Renewal of corroded slide chairs duly removing the old slide chairs by heating using
contractors gas and equipments or any approved methods and inserting Railways new
slide chairs and plate screws including crossing of tracks, leading all required materials
to site, stacking all released materials, with all contractor's tools,consumables,labour,
lead, lift and incidental charges etc complete as directed by the Engineer in charge.
Details of cost for 12 Slide chairs

Material:
Acetylene Gas (in cylinder) Kg 0341 65.00 1.00 65.00
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P ( Includes Gas cutting torch ) Lumpsum 9901 1.00 60.00 60.00
2,750.00
2,777.50

Code (Rs.) (Rs.)
3,167.74
3,642.90
Cost for 12 Nos. 3,679.33
Rate per Slide chair Each 306.61
074110 Fabrication, supply and fixing of hand operated lever boxes with pull rod of 33mm dia
to Drg.No. MA3040 including lead, lift, loading, unloading, tools and plants,
transportation, crossing of track wherever necessary as directed by Engineer-in-
charge at site.
Note:
1. Rate including Fabrication, Supply and Fixing of hand operated boxes.
2. Spring point lever (Self reversing type) as per drawing no. TMC-12 (Sheet 1,2,3).
Details of Cost of 2 sets

Material:
Hand lever box full set BG Each 0472 11000.00 2.00 22,000.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Hammer, Box spanner,cleaning brush etc.) Lumpsum 9901 1.00 30.00 30.00
24,689.00
24,935.89
28,439.38
32,705.29
Cost of 2 sets 33,032.34
Rate per set set Set 16,516.17
074120 Fabrication, supply and fixing of MS lock pins/bolts for stock and tongue rails made out
of MS 40mm dia of length 200mm with head cutting, lathe machining, milling, drilling,
welding the rod with MS flat of 6mm thick of suitable size as required at site with MS
split pins/bolts and supplying of remaining ancillary materials required at for locking,
including all taxes, lead, lift, loading and un loading , tools and plants, transportation,
crossing of track whenever necessary etc., complete and as directed by Engineer-in-
charge at site.
Details of cost for 10 pins

Material:
Point lock pin full set BG Each 0473 720.00 10.00 7,200.00
Man power:
Misc.:
T & P (Crow bar, Hammer, Box spanner,cleaning brush etc.) Lumpsum 9901 1.00 20.00 20.00
8,765.00
8,852.65
10,096.45

Code (Rs.) (Rs.)
11,610.91
Cost of 10 sets 11,727.02
Rate per set set Set 1,172.70
074130 Re-spacing of sleepers of existing PSC sleeper turnout including pre-marking of

sleeper spacing and packing with all contractor’s labour, tools, plants, as directed by
Engineer incharge.
Note: Prior inspection and recording defective spacing and approval of Engineer-in-
Charge shall be mandatory for operating this item.
074131 Turnout sleepers upto 2.85 m

Consider 48 sleepers of 1 in 12 turnout, 2 persons will do re-spacing of 12 sleepers
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
(i) Pre marking of sleeper spacing as required
(ii) Re spacing of sleepers with fixing fittings and packing
Misc.:
4,150.25
4,191.75
4,780.69
5,497.80
074132 Sleepers of length more than 2.85 m and up to 4.20 m

Considering 20% more that over rate upto 2.85 m
Rate per sleeper Each 074131 115.68 1.20 138.82
074133 Sleepers of length more than 4.20 m

Considering 30% more that over rate upto 2.85 m
Rate per sleeper Each 074131 115.68 1.30 150.39
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 8: Deep Screening Ballast Related Activities
CHAPTER - 8 : Deep Screening & Ballast Related Activities

Item no. Description Unit Rate Rate (Rs) Quantity Amount
Code (Rs.)
081000 1. Deep Screening Works
081010 Manual deep screening of Plain track/ turnouts as per procedure prescribed in
IRPWM, June 2020 or lates, in other than PSC sleepers of any density and throwing
away screened muck arising out of screening on toe of bank or on cess, if low or on
spoil banks above top of cutting (including throwing and leveling, if required beyond
minimum 5m from the edge of cutting which are upto 3m deep or alternatively carting
it upto 50m for disposing it off beyond cutting or platforms) as per direction of
Engineer in-charge, including cutting cess for effective drainage on both sides, one
round of kutcha packing with screened ballast and further attending to track
parameter to make track fit for 20 kmph speed complete in all respect.
Note : Payment shall be made for length along main line only for turnouts.
081011 Depth of 150 mm below bottom of sleeper of Plain Track

Considering 120 men on work site in a day Details of cost for 293 Track Metres of
deep screening (sleeper density of 1540 sleepers/km)
Considering output of 3.75 sleepers per person (450 sleepers in 293 TRM)
Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
(i) Deep Screening including one round kutcha packing
(ii) Other Works, e.g. removal/spreading of muck, cess attention etc. (@ one man per
16 TRM) :
Misc.:
T & P for Wooden Blocks Lumpsum 9901 1.00 236.00 236.00
64,661.00
65,307.61
74,483.33
85,655.83
Cost for 293 TRM 86,512.39
Rate per TRM TRM 295.26

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
14 TRM) :
Misc.:
62,508.00
63,133.08
72,003.28

Code (Rs.)
82,803.77
Cost for 260 TRM 83,631.81

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
12 TRM) :
Misc.:
63,372.00
64,005.72
72,998.52
83,948.30
Cost for 244 TRM 84,787.79

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
10 TRM) :
Misc.:
65,102.00
65,753.02
74,991.32
86,240.02
Cost for 228 TRM 87,102.42
081015 Depth of 150 mm below bottom of sleeper for Turnouts

Take 60% extra on 081011 TRM 081011 295.26 1.60 472.42

Code (Rs.)

Code (Rs.)

Take 60% extra on 081012 TRM 081012 321.66 1.60 514.66

Take 60% extra on 081013 TRM 081013 347.49 1.60 555.99

Take 60% extra on 081014 TRM 081014 382.03 1.60 611.25
081020 Manual deep screening of Plain track/ turnouts as per procedure prescribed in
IRPWM, June 2020 or lates, on PSC sleepers of any density and throwing away
screened muck arising out of screening on toe of bank or on cess, if low or on spoil
banks above top of cutting (including throwing and leveling, if required beyond
minimum 5m from the edge of cutting which are upto 3m deep or alternatively carting
it upto 50m for disposing it off beyond cutting or platforms) as per direction of
Engineer in-charge, including cutting cess for effective drainage on both sides, one
round of kutcha packing with screened ballast and further attending to track
parameter to make track fit for 20 kmph speed complete in all respect.
Note : Payment shall be made for length along main line only for turnouts.
081021 Depth of 150 mm below bottom of sleeper - For Plain Track :

Considering output of 3 sleepers per person (400 sleepers in 260 TRM)
Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
16 TRM) :
Misc.:
69,398.00
70,091.98
79,939.90
91,930.89
Cost for 260 TRM 92,850.20

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00

Code (Rs.)
14 TRM) :
Misc.:
66,812.00
67,480.12
76,961.08
88,505.24
Cost for 228 TRM 89,390.29

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
12 TRM) :
Misc.:
69,837.00
70,535.37
80,445.59
92,512.43
Cost for 216 TRM 93,437.55

Labour:
Mate (Skilled) Day 0002 609.00 6.00 3,654.00
Other Works, e.g. removal/spreading of muck, cess attention etc. (@ one man per 10
TRM) :
Misc.:
72,860.00
73,588.60

Code (Rs.)
83,927.80
96,516.97
Cost for 200 TRM 97,482.14
Take 60% extra on 081021 TRM 081021 357.12 1.60 571.39

Take 60% extra on 081022 TRM 081022 392.06 1.60 627.30
Take 60% extra on 081023 TRM 081023 432.58 1.60 692.13
Take 60% extra on 081024 TRM 081024 487.41 1.60 779.86

081030 Extra to item nos. from 081011 to 081018 and from 081021 to 081028 for disposal of
muck at a distance beyond 50m for every additional lead of 50 metres or part thereof
upto 500 metres for 1 TRM in station yard / cutting.
Details of cost for 250 Track Metre (Extra labour element required for additional
average lead of 250 metre for dispoal of muck)(@ one man per 25 TRM)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00
4,373.30
4,987.75
5,735.91
Cost for 250 TRM / 250 metres lead 5,793.27
Cost for 250 TRM / every 50 metres lead 1,158.65
Rate per TRM for every 50 metres Each 4.63
081040 Extra to item nos. from 081011 to 081018 and from 081021 to 081028 for disposal of
muck for additional lift of 1 metre or part thereof beyond 3 metre lift in case of
disposal of muck from track for 1 TRM in station yard / cutting.
average lift of 3 metre for dispoal of muck)(@ one man per 20 TRM)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00

Code (Rs.)
4,373.30
4,987.75
5,735.91
Cost for 200 TRM / 3 metre lift 5,793.27
Cost for 200 TRM / every 1 metre lift 1,931.09
Rate per TRM for every 1 metre LIFT Each 9.66
081050 Deep screening of turnout under line block within stipulated time by way of removing
the Points and Crossing assembly by using T-28 cranes, removing the entire stone
ballast bed by excavators up to shoulders to depth of 200/250/300 mm, limiting the
digging up to original formation level only, screening the removed ballast, putting back
the screened ballast on the formation in uniform layer, placing the points and crossing
assembly in designed position, dumping and spreading newly collected ballast in
cribs and shoulders, lifting of track as required so as to get a clean cushion of
300mm, shifting of sleepers to correct spacing including removal and re-fixing of
fittings wherever necessary, aligning of sleepers as per prescribed layout, initial
packing, aligning, dressing/ lowering the cess to deep screened depth up to the edge
of bank with a slope of 1 in 30, boxing of ballast to profile and making fit to run the
trains at a speed of non stop 20 KMPH as specified in IRPWM - June 2020 or latest
complete in all respect as directed by the Engineer - in - charge.
Note: Rail cutting and Rail hole drilling shall be paid under relevant items
081051 For 1 in 12 points and Crossings

Details of cost for one Points and crossing
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
For Pre Block activity: Opening of ballast, screening of ballast
For During Block activity: Screening of ballast, putting back ballast, shifting of
sleepers, lifting & packing of track
Look Out Man (Un-skilled) Day 0033 431.00 15.00 6,465.00
For Post Block activity: Dumping ballast, removing of muck, squaring of
sleepers,redriving of fittings, boxing of ballast
Machinery:
Misc.:
T&P (no rates reqd.) Lumpsum 9901 1.00 400.00 400.00
29,389.00
33,797.35
34,135.32
38,931.34
44,771.04
Cost for one set of points & Crossing 45,218.75
081052 For 1 in 8.5 Points & Crossings

For 1 in 8.5 Points & Crossings, considering deduction of 20% from 081051 Set 081051 45218.75 0.80 36,175.00

Code (Rs.)
081053 For 1 in 16 Points & Crossings

For 1 in 16 Points & Crossings considering extra 20% over item no. 081051 Set 081051 45218.75 1.20 54,262.50
082000 2. Spreading of Ballast :

082010 Recoupment of ballast in running line with railway's stone ballast from existing stacks
available along alignment either on top of cutting or on cess or at toe of bank by head
leads or by any other means and spreading to make up deficiency in the required
profile with contractor's labour, tools & plants, as directed by Engineer-in-charge.
Note: Payment shall be made based on ballast stack measurement.
082011 For average lead upto 50m and lift up to 5m

Details of cost for 200 cum
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
T & P ( Rake iron ballast, fork only ) Lumpsum 9901 1.00 10.00 10.00
15,360.00
15,513.60
17,693.26
20,347.25
Cost for 200 cum 20,550.72
082012 Extra over item no. 082011 for each additional average lead of 50m or part thereof
when total average lead exceeds 50m, but upto 250m.
Note: This item may be used only in exceptional circumstance under prior order on
record.
Details of cost for 200 cum per 50m Lead

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,943.00
3,982.43
4,541.96
5,223.26
Cost for 200 cum per 50m Lead 5,275.49
Rate per cum / 50m Lead Each 26.38
082013 Extra to item no. 082011 for each additional average lift of 1m or part thereof when
total average lift exceeds 5m.
Details of cost for 200 cum per 2m Lift

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50

Code (Rs.)

Code (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,638.50
3,674.89
4,191.21
4,819.89
Cost for 200 cum per 2m Lift 4,868.09
Cost for 200 cum per 1m Lift 2,434.04
Rate per cum / average 1 m Lift Each 12.17
083000 3. Lifting, Packing & Boxing Works :

083010 Lifting and packing for regrading the existing PSC sleeper track to required height /
level in stages not exceeding 75mm or part thereof at a time, providing permissible
ramp for the track, insertion of moorum / sand / stone ballast uniformly under the
existing track and placing the same to safe approved gradient, gauge, cushion
including levelling and one round of through packing to allow train movement at
restricted speed of 30 kmph for a specified length with all leads & lifts and fixing,
marking, painting rail level posts, tiebars at every 30m interval.
Note: Lifting of track shall be done in stages as per procedure prescribed in latest
edition of IRPWM to get the proposed final level as per approved working profile, as
Details of cost for 250 Track Metres for regrading by lifting and packing of track
(sleeper density of 1540 sleepers/km)
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Fixing & marking of rail level posts (Tie bar at every 30 m)
(ii) Lifting of track upto 75 mm at a time including insertion of moorum/sand/stone
ballast Considering output of 12 sleepers per man (385 sleeper in 250 TRM)

(iii) For one round Through packing ( For Through packing 15 sleeper per man)

Misc.:
T & P (Hydraulic Jack, Crow bars, Wire claws, cane basket, Rake ballast, Cross Lumpsum 9901 1.00 120.00 120.00
level etc.)
28,003.40
28,283.43
32,257.26
37,095.84
Cost for 250 TRM 37,466.80
083011 Extra for additional lift over 75mm for every 50mm lift or part thereof upto 275mm for
item nos. 083010 for each TRM.

Code (Rs.)
Taking average Lift of 100mm
Detail of cost for 250 TRM for 100mm Lift(@ one man per 12.5 TRM)
Labour:
For Filling extra ballast in packing zone, lifting & packing
Misc.:
T & P (Hydraulic Jack, Crow bars, Wire claws, Ballast dolly, Rake ballast, Cross Lumpsum 9901 1.00 40.00 40.00
level etc.)
8,660.00
8,746.60
9,975.50
11,471.82
Cost for 250 TRM for 100mm Lift 11,586.54
Cost for 1 TRM for 100mm Lift 46.35
Rate per TRM for 50mm Lift TRM 23.17
083020 Regrading the existing track by lowering upto required depth in stages, not exceeding
75mm in one stage including one round of through packing and making track fit for
30kmph speed at each stage of lowering as per procedure prescribed in latest edition
of IRPWM and subsequent picking up of sags / slacks and attending to misalignment
/ cross level defects during train operation, providing required ramp-in and ramp-out
for safe passage of trains, including cutting trenches across track at every 30m
interval to the required final formation level complete, and fixing, marking, painting
rail level posts, tiebars at every 30m interval as directed by engineer in-charge.
Details of cost for 250 Track Metres for regrading by lowering of track (sleeper density
of 1540 sleepers/km)
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Fixing & marking of rail level posts (Tie bar at every 30 m)
(ii) Lowering of track upto 75 mm at a time including picking up slacks Considering
output of 7 sleepers per man (384 sleeper in 250 TRM)
(iii) For one round Through packing ( For Through packing 15 sleeper per man)

Misc.:
T & P (Hydraulic Jack, Crow bars, Wire claws, Ballast dolly, Rake ballast, Cross Lumpsum 9901 1.00 130.00 130.00
level etc.)
37,926.40
38,305.66
43,687.61
50,240.75
Cost for 250 TRM 50,743.16

Code (Rs.)
083030 Boxing of ballast as per procedure prescribed in latest edition of IRPWM including
cess dressing on both sides of track. The work will include removing excess ballast
from track and putting the same in crib and shoulder by leading to a maximum of 50m
including crossing of track, deweeding on ballast section etc and as directed by
Engineer-In charge.
Details of cost for 500Track Metre ( Considering output of 25 TRM per man on both
sides )
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P ( Rake iron ballast, fork, beater, Phowrah, etc. ) Lumpsum 9901 1.00 40.00 40.00
9,395.50
9,489.46
10,822.72
12,446.13
083040 Removing, screening and salvaging ballast from track, duly digging / scarifying ballast
by beaters / wire brushes, leveling and dressing formation with specified cross slope
after salvaging ballast, separating muck by screening the salvaged ballast with
contractor's 20mm size sieve, stacking of sieved ballast for measurement on or
outside the formation along track, disposing off muck at specified locations under non-
traffic conditions with all ascents, descents, as directed by Engineer in-charge.
Note: Payment shall be made for quantity of ballast stacked after screening of
retrieved ballst from track.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
9,700.00
9,797.00
11,173.48
12,849.50
084000 4. Loading & Unloading of Ballast :

084010 Leading and loading Railway's ballast, collected at yard / depot / mid-section into
Railway's BOB / BKH / any other type of open wagon, using JCB or any other
approved mechanised method with all ascents, descents, taxes etc. with lead of
250m & all lifts complete as per specifications and as directed by Engineer in-charge
084011 Under Traffic Block Conditions:

Details of cost for 1400 cum (1 BOBY'N = 35 cum) consedering 40 BOBY'N
Labour:

Code (Rs.)
(i) For loading of ballast
Mate (Skilled) Day 0002 609.00 1.00 609.00
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 32.00 32.00
32,041.00
35,245.10
35,597.55
40,599.01
46,688.86
Cost for 1400 cum 47,155.75
084012 Under Conditions not requiring Traffic Block:

Details of cost for 1400 cum (1 BOBY'N = 35 cum) consedering 40 BOBY'N
Labour:
(i) For loading of ballast
Mate (Skilled) Day 0002 609.00 1.00 609.00
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 32.00 32.00
32,041.00
32,361.41
36,908.19
42,444.42
Cost for 1400 cum 42,868.86
084020 Leading and loading Railway's Ballast collected at yard / depot / mid-section into
Railway's covered wagon, using any approved method with all ascents, descents,
taxes etc. with lead of 250m & all lifts complete, as per specifications and as directed
by Engineer in-charge.

Details of cost for 800 cum for 20 BCN (1 BCN covered wagon = 40 cum)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For loading of ballast(Considering 4 persons for one BCN)
Machinery:
Misc.:

Code (Rs.)
T&P Lumpsum 9901 1.00 160.00 160.00
67,806.00
74,586.60
75,332.47
85,916.68
98,804.18
Cost for 800 cum 99,792.22
084022 Under Conditions not requiring Traffic Block -

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For loading of ballast(Considering 4 persons for one BCN)
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 160.00 160.00
67,806.00
68,484.06
78,106.07
89,821.98
Cost for 800 cum 90,720.20
084030 Leading and loading Railway's Sand collected at yard / depot into Railway's covered
wagon, using any approved method with all ascents, descents, taxes etc. with lead of
250m & all lifts complete, as per specifications and as directed by Engineer in-charge
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For loading of Sand(Considering 6 persons all the time with JCB )
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 122.00 122.00
34,770.00
35,117.70
40,051.74
46,059.50

Code (Rs.)
Cost for 700 cum 46,520.09
084040 Unloading of ballast from Railway's Hopper Wagons and distributing the unloaded
ballast uniformly over the track, taking out jammed ballast and profiling and boxing.

Details of cost for 700 cum / 20 hoopers (1 hooper = 35 cum )
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) For unloading of ballast in block and joining for profiling and boxing thereafter.

(ii) For distributing unloaded ballast & clearing of track, profiling and boxing

Misc.:
T&P Lumpsum 9901 1.00 124.00 124.00
20,989.00
23,087.90
23,318.78
26,595.07
30,584.33
Cost for 700 cum 30,890.17

Details of cost for 700 cum / 20 hoopers (1 hooper = 35 cum )
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) For unloading of ballast and joining for profiling and boxing thereafter.
(ii) For distributing unloaded ballast & clearing of track, profiling and boxing
Misc.:
T&P Lumpsum 9901 1.00 124.00 124.00
17,541.00
17,716.41
20,205.57
23,236.40
Cost for 700 cum 23,468.76

Code (Rs.)
084050 Unloading of Ballast from Railway's wagons other than Hopper wagons by opening
the doors of boxes and pulling & pushing down ballast with rake irons / phowrahs and
distributing unloaded ballast uniformly over the track, taking out jammed ballast,
profiling and boxing as per P.Way Manual.

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) For unloading of ballast (Considering 4 persons for one BCN) and joining for
profiling and boxing after unlading
(ii) Additional labour for distributing and profiling
Misc.:
T&P Lumpsum 9901 1.00 240.00 240.00
54,471.00
59,918.10
60,517.28
69,019.96
79,372.95
Cost for 800 cum 80,166.68

Labour:
Mate (Skilled) Day 0002 609.00 4.00 2,436.00
(i) For unloading of ballast (Considering 4 persons for one BCN) and joining for
profiling and boxing after unlading
(ii) Additional distributing unloaded ballast &profiling
Misc.:
T&P Lumpsum 9901 1.00 240.00 240.00
49,045.00
49,535.45
56,495.18
64,969.46
Cost for 800 cum 65,619.15
084060 Unloading of sand / quarry dust during block from Railway's wagons other than
Hopper wagons by opening the doors of boxes and pulling & pushing down sand with
rake irons / phowrahs taking out jammed sand and distributing unloaded sand
uniformly over the track.

Code (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 4.00 2,436.00
(i) For unloading of sand (Considering 3 persons for one BCN)
(ii) For distributing unloaded sand & clearing of track
Misc.:
T&P Lumpsum 9901 1.00 184.00 184.00
44,679.00
49,146.90
49,638.37
56,612.56
65,104.44
Cost for 700 cum 65,755.49
085000 5.Supply of Ballast

085010 Manufacturing, supply and stacking of machine crushed Track Ballast conforming to
RDSO Specification (IRS-GE-1) with latest correction slips at Railway depot or
nominated location.
Note: Distance of nearest quarry mentioned in each sub-item is only for the purpose
of selecting the items for preparation of estimates/tender schedule, based on the
minimum distance between nearest quarry and centre of supply points and will not
affect the selection of quarry during physical supply in any way till prescribed
specification is met fully.
085011 When distance of nearest quarry is upto 10 km

Details of Ballast for 100Cum
Material:
Production cost of Track Ballast in quarry including loading in truck Cum 0212 569.00 100.00 56,900.00
Transportation:
Considering average distance of 5 km. Quantity = 100 x 5 = 500 cum.Km. Rate as
per Working Sheet " Tr. Ballast"
Cost of transportation for 100 Cum Cum/km 8.78 500 4,391.70
Labour:
For stacking
62,584.70
63,210.55
72,091.63
82,905.37
Cost for 100 Cum 83,734.42
085012 When distance of nearest quarry is more than 10 km and upto 20 km

Material:

Code (Rs.)
Transportation:
Considering average distance of 15 km. Quantity = 100 x 15 = 1500 cum.Km
Rate as per Working Sheet " Tr. Ballast"
Labour:
For stacking
67,708.03
68,385.12
77,993.22
89,692.21
Cost for 100 Cum 90,589.13

Material:
Transportation:
Labour:
For stacking
73,326.06
74,059.33
84,464.66
97,134.36
Cost for 100 Cum 98,105.70

Material:
Transportation:
Labour:
For stacking
76,161.03
76,922.64
87,730.27
100,889.81
101,898.71

Code (Rs.)
Cost for 100 Cum 101,898.71


Code (Rs.)
Material:
Transportation:
Labour:
For stacking
79,956.58
80,756.15
92,102.38
105,917.74
106,976.92
Cost for 100 Cum 106,976.92
Material:
Transportation:
Labour:
For stacking
90,658.02
91,564.60
104,429.43
120,093.85
121,294.78
Cost for 100 Cum 121,294.78
Material:
Transportation:
Labour:
For stacking
109,896.81
110,995.78
126,590.68

Code (Rs.)
145,579.28
147,035.08
Cost for 100 Cum 147,035.08
Material:
Transportation:

Labour:
For stacking
130,034.09
131,334.44
149,786.92
172,254.96
173,977.51
Cost for 100 Cum 173,977.51
Material:
Transportation:
Labour:
For stacking
150,171.38
151,673.09
172,983.16
198,930.64
200,919.95
Cost for 100 Cum 200,919.95
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 9: Welding Activities
CHAPTER - 9 : Welding Activities

(Note: Items of this chapter shall be executed only through special tender)
Code (Rs.) (Rs.)
091000 1. Supply of Alumino Thermic Welding Portions
091010 Manufacturing and Supply of Alumino thermic welding portions of 52Kg/60 Kg/60EI-
R260 as approved by RDSO for welding of rails 52Kg/60Kg/60EI-R260 kg for 25mm
gap by the process of AT welding along with complete accessories confirming to the
specification laid down in Indian Railway Standard specification No.IRST-19-2020 up
to date correction slips with Single shot crucible fitted with Automatic Tapping
Thimble, 3 pieces pre fabricated mould (Zircon washed) manually pressed using
compressed air petrol/LPG pre heating for execution of welding of rail joint including
consumable stores complete and as directed by the engineer in charge at site.
Note:
1. The accessories along with welding portion shall be supplied as per Annexure-I of
the IRUSSOR - 2021.
2. Rate is inclusive of transportation of above to SSE/P.Way stores.
091011 For 60Kg 90 UTS Rails

Details of cost for 10 portions
Material:
Supply of Alumino Thermit Welding Portions, 3 piece prefabricated mould (ZIRCON Each 0417 1610.00 10.00 16,100.00
WASHED) manully pressed, Single shot cricible fitted with auto tapping thimble as
per RDSO Specification No IRST/19-2020 and as amended for 60 Kg/90UTS-25mm
gap with accessories as per Annexure -I of IRUSSOR - 2021.
18,362.05
21,116.36
Cost for 10 portion 21,327.52
Rate per portion Each 2,132.75
091012 For 52Kg 90 UTS Rails

Details of cost for 10 portions
Material:
17,951.47
20,644.19
091013 For 60Kg/60EI- R260 rails

Details of cost for 10 portion
Material:
per RDSO Specification No IRST/19-2020 and as amended for 60 Kg/60EI-R260
grade Rail-25mm gap with accessories as per Annexure -I of IRUSSOR - 2021.
17,951.47

Code (Rs.) (Rs.)
20,644.19
092000 2. Alumino Thermic Welding Works

092010 Alumino Thermic 25mm gap 'in-situ' welding of rail joint, during traffic block, as per
IR's AT Welding Manual with latest correction slips, complete in all respect including
restoration of track near weld joint to original position and fixing of joggled fish plate
at new weld, to be removed after passing of weld in USFD test.
Note:
1. Welding shall be carried out only by trained welder having valid competency
certificate using RDSO approved Alumino Thermit Welding Portions, 3 piece
prefabricated mould (ZIRCON WASHED) manully pressed, Single shot cricible fitted
with auto tapping thimble and Compressed Air Petrol/LPG preheating technique as
per RDSO Specification No IRST/19-2020 with latest amendment.
2. Hydraulic Weld trimmer shall be used for chipping and profile Grinder for finishing.
3. Only required nos. of Joggled fish plates shall be issued by Railway at nearest P.
Way Store which shall be returned at the same place after release from track.
092011 For 60 Kg - 90 UTS Rail

Material:
Anti-corrosive Bituminous Paint (Black) confirming to IS:9862 Litre 0304 80.00 0.25 20.00
Labour:
Chipper (Skilled) Day 0030 609.00 1.00 609.00
Luter (Skilled) Day 0031 609.00 1.00 609.00
Machinery:
Hire charges of Generator 5 KVA (without POL) Day 0072 500.00 0.20 100.00
Hire charges of Weld Trimmer Machine Day 0152 300.00 0.50 150.00
Hire charges of Rail Profile Weld Grinder Day 0151 100.00 0.20 20.00
13,800.30
15,180.33
15,332.13
17,486.30
20,109.24
Cost of 5 joints 20,310.34
Rate per joint Each 4,062.07
092012 For 60 Kg/60EI - R260 grade Rail


Code (Rs.) (Rs.)
Material:
Labour:
Machinery:
13,620.30
14,982.33
15,132.15
17,258.22
19,846.95
20,045.42
092013 For 52 Kg - 90/72 UTS Rail

Material:
Labour:
Machinery:

Code (Rs.) (Rs.)
13,620.30
14,982.33
15,132.15
17,258.22
19,846.95
092014 For 90R Rail

Rate same as 52 Kg rail
Rate per joint Each 092013 4,009.08
092020 Alumino Thermic 25mm gap 'in-situ' welding of rail joint with welding portion supplied
by Railway, during traffic block, as per IR's AT Welding Manual with latest correction
slips, complete in all respect including restoration of track near weld joint to original
position and fixing of joggled fish plate at new weld, to be removed after passing of
weld in USFD test.
Note:
1. Only welding portion and related accessories shall be supplied by Railways.
certificate.
4. Required nos. of Joggled fish plates shall be issued by Railway at nearest P. Way
Store which shall be returned at the same place after release from track.
092021 For 60 Kg Rail, Single shot crucible fitted with Automatic Tapping Thimble , 3 pieces
Mould (Zircon washed) and Compressed Air Petrol/LPG pre heating technique

Material:
Shearing Blade for weld trimming machine Each 0462 150.00 1.00 150.00
Grinding Stone wheel GQ6 of 150mm dia Nos. 0461 490.00 0.30 147.00
Labour:
Machinery:
6,100.30
6,710.33

Code (Rs.) (Rs.)
6,777.43

Code (Rs.) (Rs.)
7,729.66
8,889.11
092022 For 60 Kg/60EI-R260 grade Rail, Single shot crucible fitted with Automatic Tapping
Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol
heating technique.
Material:
Labour:
Machinery:
5,669.30
6,236.23
6,298.59
7,183.54
8,261.08
092023 For 52 Kg - 90 UTS or 52 Kg 72UTS Rail, Single shot crucible fitted with Automatic
Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air
Petrol heating technique.
Material:
Labour:

Code (Rs.) (Rs.)
Machinery:
5,669.30
6,236.23
6,298.59
7,183.54
8,261.08
092024 For 90R Rail, Single shot crucible fitted with Automatic Tapping Thimble
Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol heating
technique.
Rate same as 52 Kg rail
Rate per joint Each 092023 1,668.74
092030 Alumino Thermic 25mm gap 'in-situ' welding of rail joint with welding portion supplied
by Railway along with welder for any cross section and grade of Rail, during traffic
block, as per IR's AT Welding Manual with latest correction slips, complete in all
respect including restoration of track near weld joint to original position and fixing of
joggled fish plate at new weld, to be removed after passing of weld in USFD test.
Note:
certificate.
4. Required nos. of Joggled fish plates shall be issued by Railway at nearest P. Way
Store which shall be returned at the same place after release from track.

Material:
Labour:
Machinery:

Code (Rs.) (Rs.)
5,060.30
5,566.33
5,621.99
6,411.88
7,373.67
092040 Alumino Thermic 25mm gap 'in-situ' welding of rail joint at cess as per IR's AT
Welding Manual with latest correction slips, complete in all respect including
restoration of track near weld joint to original position and fixing of joggled fish plate
at new weld, to be removed after passing of weld in USFD test.
Note:
certificate using RDSO approved Alumino Thermit Welding Portions, 3 piece
prefabricated mould (Zircon washed) manully pressed, Single shot cricible fitted with
auto tapping thimble and Compressed Air Petrol/LPG preheating technique as per
RDSO Specification No IRST/19-2020 with latest amendment.
092041 For 60 Kg - 90 UTS Rail

Material:
Normal unleaded Petrol Litre 0182 105.00 18.00 1,890.00
Labour:
Machinery:
23,234.30
23,466.64
26,763.71
30,778.26

Code (Rs.) (Rs.)
Rate per Joint Each 3,108.60
092042 For 60 Kg/60EI - R260 grade Rail

Material:
Labour:
Machinery:
22,945.30
23,174.75
26,430.81
30,395.43
092043 For 52 Kg - 90/72 UTS Rail

Material:
Labour:
Machinery:

Code (Rs.) (Rs.)
22,945.30
23,174.75
26,430.81
30,395.43
092044 For 90R Rail

Rate same as 52 Kg rail as per item no 092043.
Rate per Joint Each 092043 3,069.94
092050 Alumino Thermic 25mm gap 'in-situ' welding of rail joint at cess with welding portion
supplied by Railway, during traffic block, as per IR's AT Welding Manual with latest
correction slips, complete in all respect including restoration of track near weld joint
to original position and fixing of joggled fish plate at new weld, to be removed after
passing of weld in USFD test.
Note:
certificate.
092051 For 60 Kg Rail, Single shot crucible fitted with Automatic Tapping Thimble, 3 pieces
Mould (Zircon washed) and Compressed Air Petrol/LPG pre heating technique

Material:
Labour:
Machinery:
7,824.30
7,902.54
9,012.85

Code (Rs.) (Rs.)
10,364.78
092052 For 60 Kg/60EI-R260 grade Rail, Single shot crucible fitted with Automatic Tapping
Thimble, 3 pieces Mould (Zircon washed) and Compressed Air Petrol/LPG pre
heating technique.
Material:
Labour:
Machinery:
7,824.30
7,902.54
9,012.85
10,364.78
092053 For 52 Kg - 90 UTS or 52 Kg-72 UTS Rail, Single shot crucible fitted with Automatic
Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air
Petrol heating technique.
Material:
Labour:
Machinery:

Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
7,824.30
7,902.54
9,012.85
10,364.78
093000 3. Flash Butt Welding Works

093010 Flash Butt Welding of 90 UTS rails, conforming to IR’s Manual for Flash Butt Welding
of Rail, using contractor’s self-propelled rail cum road / Mobile FBW Plants, tools,
equipments and consumables. Item also includes painting with anticorrosive paint as
approved and marking of welded joints, pre-straightening & post-straightening of
panels and USFD testing of finished weld as directed by engineer in-charge.
093011 52 Kg on Cess
Details of cost for 40 welds
Material:
Grinding Stone wheel GQ6 of 150mm dia Nos. 0461 490.00 2.50 1,225.00
Anti-corrosive Paint as per RDSO's Specn. No. M&C/PCN/123/2012 Litre 0305 280.00 2.00 560.00
Diesel (HSD) Oil Litre 0181 101.62 200.00 20,324.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
(a) For welding
Machinist (operator) (Skilled) Day 0040 609.00 2.00 1,218.00
Hammer man (Semi-skilled) Day 0032 505.00 1.00 505.00
Grinderman (Skilled) Day 0028 609.00 1.00 609.00
Track Machine Maintainer (Semi skilled) Day 0042 505.00 2.00 1,010.00
(b) For USFD testing
USFD Operator (With approved Certificate) Day 0043 1500.00 1.00 1,500.00
Machinery:
Hire Charges for Mobile Flash Butt Welding Plant Day 0126 55000.00 1.00 55,000.00
Hire charges of Road Cum Rail vehicle for transporting Flash Butt Welding plant Day 0125 1000.00 1.00 1,000.00
Hire charges of Crane 10T capacity Day 0089 5000.00 1.00 5,000.00
Hire charges of Angle Grinder Day 0150 200.00 1.00 200.00
Hire charges of USFD testing machine Day 0129 800.00 1.00 800.00
Misc.:
T&P Lumpsum 9901 1.00 500.00 500.00
LS for Training charges at LKO Lumpsum 9901 1.00 200.00 200.00
100,959.00
101,968.59
116,295.18
133,739.45

Code (Rs.) (Rs.)
Cost for 40 welds 135,076.85
Rate per weld Each 3,376.92
093012 60 Kg on Cess
Material:
Grinding Stone wheel GQ6 of 150mm dia Nos. 0461 490.00 2.50 1,225.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
(a) For welding
Machinist (operator) (Skilled) Day 0040 609.00 1.00 609.00
Machinery:
Hire charges of Road Cum Rail vehicle for transporting Flash Butt Welding plant Day 0125 1000.00 1.00 1,000.00
Misc.:
T&P Lumpsum 9901 1.00 500.00 500.00
94,864.00
95,812.64
109,274.32
125,665.46
093013 52 Kg 'in-situ' under traffic block

Material:
Cotton Jute Kg 0494 40.00 1.50 60.00
Labour:
(a) For welding

Code (Rs.) (Rs.)
USFD Operator (With approved Certificate) Day 0043 1500.00 0.50 750.00
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 500.00 500.00
80,063.50
88,069.85
88,950.55
101,448.10
116,665.32
093014 60 Kg 'in-situ' under traffic block

Material:
Cotton Jute Kg 0494 40.00 1.50 60.00
Labour:
(a) For welding
Grinderman (Skilled) Day 0028 609.00 2.00 1,218.00
USFD Operator (With approved Certificate) Day 0043 1500.00 0.50 750.00
Machinery:
Misc :
T&P Lumpsum 9901 1.00 500.00 500.00

Code (Rs.) (Rs.)
77,300.00
85,030.00
85,880.30
97,946.48
112,638.45
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 10: Reconditioning of Points Crossings
CHAPTER - 10 : Reconditioning of Points & Crossings

Code (Rs.) (Rs.)
101000 1. Built-Up Crossing :
101010 In-situ re-conditioning of worn out 1:8½ built-up / fabricated crossing on all types of
rail sections under traffic by RDSO approved agency, as prescribed in ‘IR's
Reconditioning of Points & Crossings Manual’ with RDSO approved electrodes and
suppliers, finishing & grinding within permissible tolerance limit, as directed by
engineer in-charge.
Note : One obtuse crossing shall be considered equivalent to two nos. of 1:8½
crossing for payment.
101011 Using H3 electrodes

Details of cost for 3 crossings (40 nos.electrodes are required for each crossing)
Material:
H3 Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0427 20.00 120.00 2,400.00
Labour:
Welder (Skilled) Day 0029 609 2.00 1,218.00
Machinery:
Hire charges of Grinding Machine for 150 mm dia wheel Day 0149 300.00 1.00 300.00
Misc.:
Electricity Charges ( 1 Unit ) KWH 0505 7.50 120.00 900.00
T&P Lumpsum 9901 1.00 10.00 10.00
8,530.00
8,615.30
9,825.75
11,299.61
Cost for 3 crossings 11,412.61
Rate per crossing Each 3,804.20
101012 Using H3A electrodes

Material:
H3 A Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0426 38.75 120.00 4,650.00
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
10,780.00
10,887.80

Code (Rs.) (Rs.)
12,417.54
14,280.17
101013 Using H3B electrodes

Material:
H3 B Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0425 76.50 120.00 9,180.00
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
15,310.00
15,463.10
17,635.67
20,281.02
101014 Using H3C electrodes

Material:
H3 C Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0424 78.13 120.00 9,375.60
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
15,505.60
15,660.66
17,860.98
20,540.12

Code (Rs.) (Rs.)
101020 In-situ reconditioning of worn out 1:12 or flatter built-up / fabricated crossing on all
types of rail sections under traffic condition by RDSO approved agency, as
prescribed in ‘IR's Reconditioning of Points & Crossings Manual’ with RDSO
approved electrodes and suppliers, finishing & grinding within permissible tolerance
limit, as directed by engineer in-charge :

Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
9,355.00
9,448.55
10,776.07
12,392.48

Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
12,167.50
12,289.18

Code (Rs.) (Rs.)
14,015.80

Code (Rs.) (Rs.)
16,118.17

Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
17,830.00
18,008.30
20,538.47
23,619.24

Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
18,074.50
18,255.25
20,820.11
23,943.12

Code (Rs.) (Rs.)
102000 2. CMS Crossing :

102010 Reconditioning of worn-out 1:8½ CMS (Cast Manganese Steel) crossing on all types
of rail sections on Cess or Depot by RDSO approved agency, as prescribed in ‘IR's
engineer in-charge.
Note: One obtuse crossing shall be considered equivalent to two nos. of 1:8½
crossing for payment.

Material:
Labour:
Machinery:
Misc.:
T & P (Cooling tub,etc.,) Lumpsum 9901 1.00 30.00 30.00
9,806.00
9,904.06
11,295.58
12,989.92

Material:
Labour:
Machinery:
Misc.:
12,618.50
12,744.69

Code (Rs.) (Rs.)
14,535.31
16,715.61

Material:
Labour:
Machinery:
Misc.:
18,281.00
18,463.81
21,057.98
24,216.67

Material:
Labour:
Machinery:
Misc.:
18,525.50
18,710.76
21,339.62
24,540.56

Code (Rs.) (Rs.)
102020 Reconditioning of worn out 1:12 or flatter CMS (Cast Manganese Steel) crossing on
all types of rail sections on Cess or Depot, as prescribed in ‘IR's Reconditioning of
Points & Crossings Manual’ with RDSO approved electrodes and suppliers, finishing
& grinding within permissible tolerance limit, as directed by engineer in-charge.

Material:
Labour:
Machinery:
Misc.:
11,062.00
11,172.62
12,742.37
14,653.73

Material:
Labour:
Machinery:
Misc.:
14,437.00
14,581.37
16,630.05
19,124.56

Code (Rs.) (Rs.)

Material:
Labour:
Misc.:
21,232.00
21,444.32
24,457.25
28,125.83

Material:
Labour:
Machinery:
Misc.:
21,525.40
21,740.65
24,795.22
28,514.50

Code (Rs.) (Rs.)
102030 Reconditioning of worn-out all types of CMS (Cast Manganese Steel) crossings on all
types of rail sections 'in-situ' under traffic conditions using RDSO approved
Translamatic Robotic Welding technology alongwith approved agency, finishing &
grinding within permissible tolerance limit, as directed by engineer in-charge.
Note : (1) One obtuse crossing shall be considered equivalent to two nos. of crossing
for payment. (2) Reconditioned crossing shall give a service life of minimum 80 GMT.
In case of pre-mature reconditioning, it shall be done by the contractor free of cost.
Details of cost for 1 crossing (6.5 Kg of 1.6mm dia core flux wire required for each
crossing)
Material:
1.6mm dia core flux wire of cast manganese steel Kg 0428 916.00 6.50 5,954.00
Labour:
Welder (Skilled) Day 0029 609 1.00 609.00
Machinery:
Hire charges of translamatic robotic welding machine Day 0134 5000.00 1.00 5,000.00
T&P Lumpsum 9901 1.00 1000.00 1,000.00
20,814.00
21,022.14
23,975.75
27,572.11
Cost for 1 crossing 27,847.83
103000 3. Switches / Tongue Rails :

103010 In-situ reconditioning of worn out 1:8½ tongue rail (only one tongue rail alongwith
connected stock rail) of all rail sections under traffic, as prescribed in ‘IR's
suppliers, finishing & grinding within permissible tolerance limit, with all contractor's
own power T&P, men and materials including crossing the track,lead lift and as

Details of cost for 12 Tongue rail (18 nos.electrodes are required for each Tounge
Rail)
Material:
Labour:
Machinery:

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
11,170.00
11,281.70
12,866.78
14,796.80
Cost for 12 Tongue Rails 14,944.76
Rate per Tongue Rail Each 1,245.40

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
15,220.00
15,372.20
17,531.99
20,161.79

Rail)
Material:
Labour:
Machinery:
Misc.:

Code (Rs.) (Rs.)
T&P Lumpsum 9901 1.00 10.00 10.00
23,374.00
23,607.74
26,924.63
30,963.32

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
23,726.08
23,963.34
27,330.19
31,429.72
103020 In-situ reconditioning of worn out 1:12 or flatter tongue rail (only one tongue rail
alongwith connected stock rail) of all rail sections under traffic, as prescribed in ‘IR's
engineer in-charge :

Rail)
Material:
Labour:

Code (Rs.) (Rs.)
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
10,730.00
11,803.00
11,921.03
13,595.93
15,635.32

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
14,480.00
15,928.00
16,087.28
18,347.54
21,099.67

Rail)
Material:
Labour:

Code (Rs.) (Rs.)
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
22,030.00
24,233.00
24,475.33
27,914.11
32,101.23

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
22,356.00
24,591.60
24,837.52
28,327.19
32,576.27
103030 Reconditioning of worn out 1:8½ tongue rail (only one tongue rail alongwith
connected stock rail) of all rail sections on Cess or Depot, as prescribed in ‘IR's
engineer in-charge.


Code (Rs.) (Rs.)
Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
13,206.00
13,338.06
15,212.06
17,493.87

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
18,006.00
18,186.06
20,741.20
23,852.38

Rail)
Material:

Code (Rs.) (Rs.)
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
27,670.00
27,946.70
31,873.21
36,654.19

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
28,087.28
28,368.15
32,353.88
37,206.96
103040 Reconditioning of worn out 1:12 or flatter tongue rail (only one tongue rail alongwith
connected stock rail) of all rail sections on Cess or Depot, as prescribed in ‘IR's
engineer in-charge.


Code (Rs.) (Rs.)
Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
13,096.00
13,226.96
15,085.35
17,348.15

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
17,821.00
17,999.21
20,528.10
23,607.31

Rail)
Material:

Code (Rs.) (Rs.)
Labour:

Code (Rs.) (Rs.)
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
27,334.00
27,607.34
31,486.17
36,209.10

Rail)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
27,744.76
28,022.21
31,959.33
36,753.23
104000 4. SEJ (Switch Expansion Joint), Weld and Rail:

104010 Re-conditioning of worn out all types of SEJs of all rail sections to the standard
profile by using H3A electrodes as per RDSO drawing and prescribed in ‘IR's
Reconditioning of Points & Crossings Manual’ including grinding to finished
tolerances etc. complete.
Note: Two stock rails + Two tongue rails will constitute one set of SEJ.
104011 On Cess condition

Details of cost for 4 set SEJ (60 nos.electrodes are required for each SEJ)
Material:
Labour:

Code (Rs.) (Rs.)
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
18,028.00
18,208.28
20,766.54
23,881.52
Cost for 4 set SEJ 24,120.34
104012 In-situ under traffic condition

Details of cost for 3 set SEJ (64 nos.electrodes are required for each SEJ)
Material:
Labour:
Machinery:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
14,010.00
15,411.00
15,565.11
17,752.01
20,414.81
Cost for 3 set SEJ 20,618.96
104020 Re-conditioning of cupped welded joints 'in-situ' by using CP-3032 powder under
traffic conditions as per RDSO’s guidelines for ‘IR's Reconditioning Of Scabs, Wheel
Burns Of Rail And Cupped AT Welded Joint’
Details of cost for 30 Welds

Material:
CP-3032 Powder for reconditioning of scabs, wheel burns of rails and cupped AT Kg 0422 1550.00 8.00 12,400.00
welded joints
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 2.00 80.00

Code (Rs.) (Rs.)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
14,826.00
14,974.26
17,078.14
19,639.87
Rate per weld Each 661.21
104030 Repairs/Reconditioning of scabbed rails & wheel burns on tongue rails / running
rails/stock rails etc in situ using Micro flow thermal spray technology by using CP –
3032 powder as approved and as per RDSO / LKO and as per specifications with all
Contractor’s material, labour, tools, powder, equipment and consumable, with all lead
and lift complete and as per the instructions of the Engineer-in-charge at site.
Details of cost for 1000 Sq cm

Material:
CP-3032 Powder for reconditioning of scabs, wheel burns of rails and cupped AT Kg 0422 1550.00 8.00 12,400.00
welded joints
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
14,826.00
14,974.26
17,078.14
19,639.87
Cost for 1000 Sq.cm 19,836.26
Rate per Sq.cm Sq cm 19.84
104040 Insitu reconditioning of MCI insert of points & crossings sleeper by reclaimimg the
wornout portion to the desired height, grinding of the finished profile for regaining the
toe load lost. The reconditioning to be done by using TERRA C I-94 - Electrodes of
make L & T, AdvaniOerlicon, Diffusion, SHARP - 650, or equivalent approved by
RDSO for reconditioning of Cast iron alloys. removing and refixing the required
fittings for reconditioning in traffic condition. The cost includes all labour, lead lift,
transportation of men and material, cost of consumables, hiring of machinery
required etc, complete and as directed by the Engineer-in -charge.
Cost Considering for 70 Nos for reconditining of inserts in one day

Each electrode required for one insert reconditioning

Code (Rs.) (Rs.)
Material:
TERRA C I-94 - Electrodes of make L & T, AdvaniOerlicon, Diffusion, SHARP - 650, Each 0423 175 70.00 12,250.00
or equivalent for reconditioning of MCI insert of points & crossings sleeper
Labour:
Helper (Semi-skilled) Day 0021 505 1.00 505.00
Grinderman (Skilled) Day 0028 609 1.00 609.00
Waterman (Un-skilled) Day 0034 431 1.00 431.00
Look Out Man (Un-skilled) Day 0033 431 1.00 431.00
Misc.:
T & P (Welding plant misc tools) and gringing blades etc Lumpsum 9901 1 20 20.00
Hire charges of Arc Welding Machine 500 Amp Day 0132 300 1.00 300.00
Hire charges of Angle Grinder Day 0150 200 1.00 200.00
15,355.00
15,508.55
17,687.50
20,340.63
Cost for 70 inserts 20,544.03
Rate per insert Each 293.49
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 11: Formation Rehabilation
CHAPTER - 11 : Formation Rehabilitation

(These items shall be used only for Rehabilitation of poor formation under running line)
Code (Rs.) (Rs.)
111000 1. Earth-Work :
111010 Removing existing ballast neatly from shoulder, crib and below sleepers under traffic
so as to completely expose formation top for formation treatment / repairs and
training out the same after completion of formation treatment work, initial packing the
track for safe running of trains at speed of 20 kmph, achieving desired track
geometry, as directed by engineer in-charge and dressing of ballast as per IRPWM
Details of cost for 100TM
Labour:
(i) For removing existing ballast from shoulder, crib & below the sleeper
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For putting back ballast,For boxing, packing, dressing etc.
Mate (Skilled) Day 0002 609.00 1.50 913.50
Misc.:
T&P Lumpsum 9901 1.00 120.00 120.00
28,795.50
31,675.05
31,991.80
36,486.65
41,959.65
Cost for 100 TM 42,379.24
111020 Insertion & spreading of blanketing material, conforming to RDSO’s specifications,

uniformly under the existing BG track in layers of maximum 75mm thickness at a
time upto the proposed formation level as per approved drawing by duly lifting the
existing track in stages under the running conditions, consolidating every layer of
blanketing material manually or mechanically in stages from stacks collected on
either side of track and packing the track for safe running of trains at speed of 30
kmph, achieving desired track geometry, as directed by engineer in-charge.
Notes:
1.Supply of blanketing material shall be paid separately.
2.Payment will be done as per pre-recorded stack measurement with deduction for
voids. 3. Any damage to the side drain/retaining wall during dumping should be made
good by the contractor, failing which recovery for twice the cost of repair will be made
from contractor.
4. Prior permission of Engineer-in-charge shall be obtained for dumping - STACK
WISE. No payment will be made in case no such prior approval is obtained by
contractor. Uniformity in dumping is to be ensured throughout the length in
proportionate to regrading.
5. STAGE PAYMENTS:
a) 40% of rate will be paid - After uniform dumping on the track.
b) 20% of rate will be paid - After fully salvaging all the moorum at stack location
c) 20% of rate will be paid- After compaction of shoulder and crib.
d) 20% of rate will be paid - After profiling the formation. 6) At deep cuttings and high
banks, the moorum available on either side of bank/cutting has to be led to the
formation by contractor's own means.
7) In case of leads more than 250m and lift more than 5m it will be paid under
relevant item.
8) Agency shall obtain prior permission of Engineer in charge before stacking the
Blanket material.

Code (Rs.) (Rs.)
111021 Without Traffic Block condition
Labour:
(i) For Dumping of blanketing material on cess etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For mixing of blanketing material
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iii) For Spreading in shoulder/crib
(iv) Compaction of blanketing material
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 112.00 112.00
26,937.00
27,206.37
31,028.86
35,683.19
111022 During Traffic Block condition

Labour:
(i) For Dumping of blanketing material on cess etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For mixing of blanketing material
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iii) For Spreading in shoulder/crib
(iv) Compaction of blanketing material
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 112.00 112.00
27,368.00
30,104.80
30,405.85
34,677.87
39,879.55

Code (Rs.) (Rs.)
111030 Excavation, loading, leading, unloading of excavated earth / muck / dismantled
rubbish of CC / masonry in foundation from platform in-between running / adjacent to
track and by manual or any other suitable means or descent/ascent, crossing of
tracks, signal wires, OHE wires, passenger crowds or any other obstructions etc.
upto a lead of 1 Km.

Labour:
(i) For excavation of earth
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For loading & unloading
Misc.:
T&P Lumpsum 9901 1.00 60.00 60.00
10,058.00
10,158.58
11,585.86
13,323.74
112000 2. Soil Testing :

112010 Slope stability calculation and design for Railways Embankment / Cutting more than
6 meters height based on soil materials & parameters as per RDSO's latest
standards and specifications, duly conducting relevant lab test, e.g. cohesion and
angle of internal friction etc. and submitting report for approval duly showing the
cross-section dimensions for embankment / cutting for each cross section.
112011 Embankment
For Lab test on collected soil samples as per relevant IS code Rates are avaliable in
Works SOR item no. 021140
Detail of cost for samples of 20 cross sections
Labour:
Draftsman / Surveyor Day 0001 1500.00 2.00 3,000.00
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
Hire charges of Laptop / Computer with software & Printer Day 0166 300.00 1.00 300.00
7,168.00
7,239.68
8,256.86
9,495.38
Cost for samples of 20 cross sections 9,590.34
Rate for each cross sections Each 479.52
112012 Cutting

Code (Rs.) (Rs.)
For Lab test on collected soil samples as per relevant IS code Rates are avaliable in
Works SOR item no. 021140
Detail of cost for samples of 20 cross sections
Labour:
Misc.: Lumpsum 9901 1.00 50.00 50.00
8,535.00
8,620.35
9,831.51
11,306.24
Cost for samples of 20 cross sections 11,419.30
Rate for each cross sections Each 570.96
113000 3. Miscellaneous Works :

113010 Excavation in all types of soil for formation treatment below track under speed
restriction of 20 kmph upto specified depth & width including making up the cess as
per standard profile or spreading earth on bank, if the same is not required for cess
making and leveling the excavated bed to slope of 1 in 40 towards cess. The rate
also includes working during traffic block for excavation, removal and insertion of
Railway’s Aluminum Alloy Girders or Rail Clusters on C.C. crib for making temporary
arrangement alongwith erection and removal of cribs, all wooden packing required
and loading, unloading, shifting operations including carriage of girders including
carting of materials back to store etc. complete including lifting and packing of
sleepers and maintaining the track parameters, as directed by engineer in-charge.
113011 With Railway’s Aluminum Alloy Girders

Labour:
(i) For excavation of soil
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For leading wooden sleeper
(iii) For inserting crib both side
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iv) For insertion of railway aluminum alloy girder
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iv) For removal of girder & crib
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(v) For carting of all materials back to store
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
(vi) For lifting and packing of track
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 404.00 404.00
97,669.00
102,552.45
103,577.97
118,130.68
135,850.28
Cost for 45 cum 137,208.78
113012 With Rail Clusters, fabricated by contractor with rails supplied by Railways
Labour:
(i) For excavation of soil
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For leading wooden sleeper
(iii) For inserting crib both side
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iv) For preparation of rail cluster (with carting of rail)
(iv) For insertion of rail cluster
Mate (Skilled) Day 0002 609.00 1.50 913.50
(v) For removal of cluster & crib
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(vi) For carting of all materials back to store
Mate (Skilled) Day 0002 609.00 1.00 609.00
(vii) For lifting and packing of track
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 452.00 452.00

Code (Rs.) (Rs.)
108,869.50
114,312.98
115,456.10
131,677.69
151,429.34
Cost for 40 cum 152,943.63
113020 Laying and spreading blanketing material from stacks by the side of track after
removing ballast and filling the same in 15cm thick layer in track, levelling, watering,
ramming with hand rammers upto the formation top during formation treatment,
putting back ballast and packing in running traffic condition at speed restriction of 20
kmph for lead upto 250m and lift upto 5m.

Labour:
(i) For spreading including lead, lift etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For leveling, watering & ramming etc
Misc.:
T&P Lumpsum 9901 1.00 76.00 76.00
18,356.00
18,539.56
21,144.37
24,316.02
113021 Extra to item no. 113020 for every 50 metres lead or part thereof when the lead
exceeds the initial 250 metres per Cum.
Details of cost for 20 Cum (Extra labour element required for additional average lead
of 250 metre for leading of blanket material)(@ one man per 2 Cum)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00
4,373.30
4,987.75
5,735.91
Cost for 20 Cum / 250 metres lead 5,793.27
Cost for 20 Cum / every 50 metres lead 1,158.65
Rate per Cum per 50m lead Each 57.93

Code (Rs.) (Rs.)
113022 Extra to item no. 113020 for every 1 metres height / lift or part thereof, when the lift
exceeds initial 5 metres per Cum.
Details of cost for 20 Cum (Extra labour element required for additional average lift of
3 metre for leading of blanket material)(@ one man per 2 Cum)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00
4,373.30
4,987.75
5,735.91
Cost for 20 cum / 3 metre lift 5,793.27
Cost for 20 Cum / every 1 metre lift 1,931.09
Rate per Cum per 1 m lift Each 96.55
113030 Repairing of embankment with contractor's own earth including , excavation / loading
into contractor's vehicle as per RDSO latest Specifications and guidelines
RDSO/2020/GE: IRS-0004 of Soil Quality Class SQ1 in cess / formation / level
crossing, rain cuts etc. in running line to make surface to the desired level and slope
to entire satisfaction of Engineer in-charge. Rate shall include uprooting and
disposing of all the vegitation, benching at every 30 Cm vertical height, earthwork for
benching cut portion, adding moisture to earth to bring it to Optimum Moisture
Content, , sectioning to profile, all lift, descends, ascends, crossing of track / road /
nallah etc. including breaking of clods etc. and compaction by slope vibratory
Rollers/Compactors etc.
Note: (1) Payment of cess repairs shall be based on the quantities worked out from
the cross sectional calculations only and worked out from the initial ground levels
before doing benching and final levels as done for new embankment. The earth work
in benching portion shall not be paid.
(2) The earth work shall be started only after Completing of the benching and
certified.
(3) The benching Work shall be done for a maximum height of 1.50 m at any time
based on the the progress of earthwork starting from toe of the embankment.
Detail of cost for 100 cum

Add Extra for earth work for benching and Wastage
Assuming 3m Height of Bank,
Number of Steps of Benching = 10
Area of 10 Steps of Benching = 10 x 0.5 x 0.30 x 0.60 = 0.90 Sqm
Assuming width of Earth work to be done = 1.00 m
Area of Earthwork to be done = 3.00 x 1.00= 3.00 Sqm.
% of earthwork for benching = 0.90/3.00 x 100 = 30%
Material:
Soil Quality Class SQ1 suitable for sub grade of embankment as per RDSO Cum 0168 75 130 9,750.00
Labour:
Unskilled Labour for removing vegitation and Benching
Benching quantity for 33m length (100 Cum /3.00 sqm) = 33.33* 0.90 =30.00 Cum
Labour Unskilled Day 0020 431 10 4,310.00

Machinery:
Hire charges of Hydraulic Excavator (0.9 Cum Bucket Capacity) Day 0044 6400 0.40 2,560.00
Hire Charges of Slope Vibrator to be attached to Hydralic Excavator for rolling of Day 0054 2000 0.40 800.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1 50 50.00
17,470.00

Code (Rs.) (Rs.)
17,644.70
20,123.78
23,142.35
Cost for 100 cum 23,373.77
113040 Excavation for widening of existing formation in cuttings in hard soils which require
picks or crow bars for hacking including soils containing stones or boulders of size
under 0.03 cum without infringing the nearby track, as directed by engineer-in-charge
at site including cutting of earth, loading, leading by contractor’s vehicles, unloading
at site, dumping on spoil bank by head loads and utilising same excavated earth for
widening of existing formation in embankment as per standards, duly rolling manually
at 2:1 slope and levelling bank to the required profile including watering and
compaction with contractor's labour or mechanically operated rollers with all
contractor's labour, clearing of jungle, benching etc., tools, plants, vehicles etc.
Detail of cost for 40 cum
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
14,939.00
15,088.39
17,208.31
19,789.56
113050 Extra over item 113030 for earth-work for making cess on other side of the track
(when no approaches available along track or no road vehicles to work at site) by
dumping contractor's own earth, collected along toe of bank of any height on to other
side of track & side slope of the existing bank by head load, duly crossing of tracks
with all contractor's materials, labour, tools, plant including loading of earth in
baskets, lifting, leading to the non-cess side of bank including crossing of tracks &
dumping etc. and as directed by the Engineer in-charge.
Take 10% of relevant item rate Cum 113030 233.74 0.10 23.37
113060 Removal of the existing track panels of each of about 12.60m length from track
formations with Contractor's 30T capacity crawler cranes of three Nos, placing the
removed track panels on level ground along the toe of the formation and and bringing
back the removed track panels and placing on the track formation after completion of
laying of blanketing and spreading the ballast duly deploying the three nos of 30T
capacity crawler cranes (including one stand by crane) and one round of initial
packing during traffic block with all contractor's men, machinery, operators and
supporting staff to machinery, fuel, comsumable, tools and plants and all incidental
charges etc ., as directed by the Engineeer-in -charge.
Note:
Contractor has to make ramps to take machines onto formation and back, removing
the ramp and making formation slope and dressing to standard profile after
It is considered that this work of 1Km length can be carried out with 3 nos of 30T
capacity crawler cranes in 10 days.
Labour:
Mate (Skilled) Day 0002 609 10.00 6,090.00
Labour required to assist to machine working while removing track panels and
placing on level ground- 2 men to each machine)
For 10 days two machines being deployed in block and one machine for stand by.

Code (Rs.) (Rs.)
Labour Unskilled Day 0020 431 20.00 8,620.00
Unskilled labour (for paking the track after laying track panels) 8 men each day for 10
days
Look Out Man (Un-skilled) Day 0033 431 10.00 4,310.00
T & P ( Hammer, Crow bars, Tami bar, beater, Wire claws, etc.) LS 9901 1.00 200.00 200.00
Machinery:
Hiring and running charges of Crane 30 MT capacity including maintenance and cost 480,000.00
Day 0093 16000 30.00
533,700.00
587,070.00
592,940.70
676,248.87
777,686.20
Cost for 1 Km 785,463.06
113070 Excavation of existing formation, after removal of track structure and removal of
ballast, to a width and depth as proposed to a length posiible to carryout in the given
period of time, duly deploying the four number of 200 HP Excavators (including one
stand by) and required no. of tippers, leading and dumping the excavated soil out
side railway boundary, laying of ramps at appropriate locations for movement of
machinery and levelling the formation after excavation during traffic block with all
contractor's men, machinery, operators and supporting staff to machinery, fuel,
consumable, tools and plants and all incidental charges etc., as directed by the
Engineer-in-charge.
Note: Contractor has to make ramps to take machines onto formation and back,
removing the ramp and making formation slope and dressing to standard profile after
completion of formation and ramps to outside railway boundary.
It is considered that this work of 1 km length can be carried out with 3 nos of Hitachi
of 210 capacity (and one stand by) in 10 days.(Quantity of earth to be excavated
from the existing formation (L=1000M,W=7.00M and D=0.55M) =3850 CuM
Labour:
Mate (Skilled) Day 0002 609 10.00 6,090.00
Men required to assist machine working
Look Out Man (Un-skilled) Day 0033 431 10.00 4,310.00
T & P ( Hammer, Crow bars, Tami bar, beater, Wire claws, etc.) Lumpsum 9901 1 500.00 500.00
Machinery:
Hire charges of Hydraulic Excavator (0.9 Cum Bucket Capacity) Day 0044 6400 40.00 256,000.00
Hire and running charges of Tipper 12 Cum Capacity Day 0048 7000 60.00 420,000.00
708,450.00
779,295.00
787,087.95
897,673.81
1,032,324.88
Cost for 3850 CuM 1,042,648.13
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 12: Activities at Construction Sites
CHAPTER - 12 : Activities at Construction Sites

Code (Rs.) (Rs.)
121000 1. Dismantling Works :
121010 Dismantling of existing BG track on all type of rails and all type of sleepers, removing
rails, sleepers, fish plates and fittings from track and cutting of rails into free rails of
length, as directed and segregation and stacking of released Rails, Sleepers and
fitting at nominated location in countable manner with in a free lead of 500m, levelling
of ballast to correct profile, so as to form a level bed for laying BG track.
Details of cost for 500 TRM

Material:
Commercial LPG (in cylinder) Kg 0339 73.71 26.00 1,916.46
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Opening ballast, fitting, fastening, joint fish plate and gas cutting if LWR
(ii) Removing rail from sleeper cess side
(iii) Collecting fitting, fastening, fish plate, nut & bolt etc.
(iv) Collecting sleepers, leading and stacking near store depot in countable manner
(v) Levelling of ballast to correct profile
Misc.:
51,521.46
52,036.67
59,347.83
68,250.00
Cost for 500 TRM 68,932.50
121020 Dismantling of existing rail / metal fencing, fixed adjoining running lines of track, duly
excavating and levelling the foundation by hand compaction, removing connections
and carting the released material up to a lead of 250m by suitable means and
stacking the same, as directed by engineer in-charge.
Note:1.The released materials shall be handed over duly stacking the same in
measurable fashion.
Details of cost for 6 MT ( For 50 m fencing of 90 R rail)

Material:
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
(i) Dismantling of fencing
(i) Leading /carting of released rail

Code (Rs.) (Rs.)
Misc.:
5,243.84
5,296.28
6,040.41
6,946.47
Cost for 6 MT 7,015.93
121030 Dismantling existing sand humps in yards from end of turnout to end of sand hump.
Scope includes dismantling of track and brick / stone masonry on either sides of
track, removing sand and earth to the required level including clearing site and
stacking released materials clear of infringement, complete and as directed.
Details of cost for each

Signal over lap 120 m considering from SRJ, Turnout length 40 m Total length of
track = 120 - 40 = 80 M {1 unskilled required for 10 metre length}
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
For Dismantling masonry and collecting and stacking released materials and for
removing sand and earth to the required level.
Misc.:
T & P (Crow bar, Rail tongue, Chisel, Hammer, Spanner, etc.) Lumpsum 9901 1.00 16.00 16.00
8,383.00
8,466.83
9,656.42
11,104.88
Cost for each 11,215.93
Rate per Sand Hump Each 11,215.93
122000 2. Shifting & Pairing Works :

122010 Shifting & pairing of rails / panels unloaded alongside existing running track to
adjoining formation including crossing of track, duly lifting & pushing rail / panel
without damaging it and taking all necessary precautions, so as not to infringe the
running track, as directed by Engineer in-charge.
Note: The disturbed rail barricading should be restored to its original condition by the
agency including re-fixing & concreting as required.
122011 Rail length upto 13m.'Under Traffic Block Conditions -

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
11,895.00

Code (Rs.) (Rs.)
12,489.75
12,614.65
14,387.01
16,545.06
Cost for 1000 RM 16,710.51
122012 Rail length upto 13m 'Under Conditions not requiring Traffic Block -
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
10,171.00
10,272.71
11,716.03
13,473.43
Cost for 1000 RM 13,608.16
122013 For rails/panels of more than 13m and upto 40m length Under Traffic Block
Conditions.
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
16,814.00
18,495.40
18,680.35
21,304.94
24,500.69
Cost for 1000 RM 24,745.69
122014 For rails/panels of more than 13m and upto 40m length Under Conditions not
requiring Traffic Block
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
13,188.00
13,319.88
15,191.32
17,470.02
Cost for 1000 RM 17,644.72
122015 For rails/panels of more than 40m length : Under Traffic Block Conditions -
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
23,532.00
27,061.80
27,332.42
31,172.62
35,848.52
Cost for 1000 RM 36,207.00
122016 For rails/panels of more than 40m length Under Conditions not requiring Traffic Block
-
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
19,222.00
19,414.22
22,141.92
25,463.21
Cost for 1000 RM 25,717.84
122017 Extra over item No 122011 for crossing each additional line
Rate as per Item No 122011
Considering additional cost per crossing one line at the rate of 10% of item no
122011

Code (Rs.) (Rs.)
Rate for crossing each additional line per Running metre RM 122011 16.71 10% 1.67
122013for crossing each additional line per Running metre
Rate RM 122013 24.75 10% 2.47
122015
Rate for crossing each additional line per Running metre RM 122015 36.21 10% 3.62
123000 3. Laying & Linking Works :

123010 Providing Centre Line / Rail Level Pegs on formation at an interval of 30 metres on
one side or at centre of proposed / existing track, as directed by engineer in-charge
for linking of new track / CTR / Deep Screening / Lifting / Lowering works, duly
embedding in formation including marking with contractor's paint (rails & tie bar pegs
of suitable size will be supplied by Railways)
Note:
(1) Rails/tie bar shall be supplied by the Railways within free lead of 250m Stores
Depot. In case of hard wood peg, the hard wood will be supplied by the contractor.
(2) Excavation and concrete work will be paid separately.
123011 With Rail pegs

Details of cost for 66 pegs ( at every 30m interval, for 1KM 33pegs are required)
Material:
Paint Brush (writing) of any size Each 0315 150.00 0.50 75.00
Labour:
(i) For carting of Rail pegs
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For fixing of Rail pegs
(iii) Painting of Rail pegs
Misc.:
T&P Lumpsum 9901 1.00 22.00 22.00
5,849.00
5,907.49
6,737.49
7,748.12
Cost for 66 Pegs 7,825.60
Rate per Pegs Each 118.57
123012 With Tie bar pegs

Material:
Labour:
(i) For carting of Tie bar pegs
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
(ii) For fixing of Tie bar pegs

Code (Rs.) (Rs.)
(iii) Painting of of Tie bar pegs
Misc.:
T&P Lumpsum 9901 1.00 22.00 22.00
5,849.00
5,907.49
6,737.49
7,748.12
123013 With contractor's hard wood pegs

Material:
Hard Wood Peg of 50mm dia & 60 cm long Each 0490 25.00 100.00 2,500.00
Labour:
(i) For carting & fixing of wooden pegs
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) Painting of wooden pegs
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
8,168.00
8,249.68
9,408.76
10,820.07
123020 Installation of reference points for track centre line in main and loop lines, in straight
or curve portion, SRJ for turnouts, heel of crossing (HOC), locations of derailing
switches, switch expansion joints etc. away from formation on firm ground at known
offset with MS Angles of 50mmx50mmx5mm thick of length 1.80 m each, protected
by surrounding concrete of size 30cm x 30cm x 45cm of nominal mix 1:3:6, including
painting to pegs, as directed by Engineer In charge.
Note: Earth work and Cement concrete will be paid under relevant items.
Details of cost for 80 pegs {For one peg requires 50mmx50mmx5mm angle of 1.80 m
length ngle)=3.80 Kgs/metre length.1.80mx80 Nos=144Rmx3.80=547.2 Kg.Wastage
5%.Total = 574.56 Kg
Material:

Code (Rs.) (Rs.)
Paint Brush 25 mm Each 0327 20.00 1.00 20.00
Man Power : (For providing Pegs)
Misc.:
T & P Including required stationery Lumpsum 9901 1.00 50.00 50.00
Hire Charges of Total Station instrument Day 0504 200.00 1.00 200.00
32,152.00
32,473.52
37,036.05
42,591.46
123030 Spreading of ballast, from existing stacks available along formation on top or at
cess, in required uniform thickness, compaction of ballast layer laid on new
formation at all the locations with smooth wheeled power roller of 8-10 tonne capacity
to sufficient number of passes to form consolidated ballast bed of approximately
250mm thickness to a width of 4m symmetrical to centre line of proposed track in
correct line & level with all ascents & descents, as directed by Engineer in-charge.
Note: Item is inclusive of (a) providing ramp for taking roller to formation and
removing the same & making good formation after completion of work; (b)
redistribution & leveling of excess ballast while rolling to obtain uniform plane
cambered surface.
Considering ballast heaped over top of formation in stackes as required for 200 mm
of ballast layer. One Dozer D-6 can doze 750 sqm/hrs i.e. 0.25*750 = 187.50
cum/hour.
Details of cost for 1000 m (For 250 mm thickness, 4 metre width and 1km length,
quantity of ballast to be spread and rolled = 0.25 x 4 x 1000 = 1000 cum)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Machinery:
Hire charges of dozer 215 HP capacity Hour 0057 1500.00 8.00 12,000.00
Hire charges of Road Roller 8 to10 tonnes Hour 0053 300.00 8.00 2,400.00
32,119.00
32,440.19
36,998.04
42,547.74
Cost for 1000 cum 42,973.22

Code (Rs.) (Rs.)
123040 Linking of BG track with any type of rail section and sleeper of specified density, on
ballast bed spread and compacted with suitable roller, over prepared formation
including leading free rails/welded panels avilable along the alignment on to
formation, leading and spreading all fittings and fastenings, spreading of sleepers at
specified spacing, squaring, placing of rails over sleepers and fixing rails to sleepers
with all types of fittings and fastenings to correct gauge & alignment, lubrication of
fittings and fastenings with contractor's grease as per IRPWM standards with
contractors labour, tools, consumables, with all lead, lifts etc. complete and raising,
levelling and initial packing of track to make it fit for 30 kmph and meet other
prequisites prescribed in Indidian Railway Track Machine Manual for deployment of
Tamping Machine.
Note:
1.Rail cutting and Hole drilling shall be paid seperately.
2.Spreading of ballast and compaction shall be paid seperately under relevant item.
123041 (a) For sleeper density of 1660 sleepers per km

Material:
Labour:
(i) Spreading Sleepes at specified spacings
Mate (Skilled) Day 0002 609.00 9.00 5,481.00
(ii) Fixing rails to sleepers with fittings & fastenings
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iii) Initial kutcha packing with spreading of ballast
Mate (Skilled) Day 0002 609.00 5.00 3,045.00
(iv) Oiling & greasing of joints & ERC's
Misc.:
T&P Lumpsum 9901 1.00 656.00 656.00
186,804.00
188,672.04
215,180.46
247,457.53
Cost for 1000 TRM 249,932.11
123042 (b) For sleeper density of 1540 sleepers per km

Material:
Labour:
(i) Spreading Sleepes at specified spacings
Mate (Skilled) Day 0002 609.00 8.00 4,872.00

Code (Rs.) (Rs.)
(ii) Fixing rails to sleepers with fittings & fastenings
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iii)Raising, leveling and initial packing (s) with spreading of ballast to make it fit for
30 kmph and minimum cushion of 250 mm for deployment of track machine.
Mate (Skilled) Day 0002 609.00 5.00 3,045.00

(iv) Oiling & greasing of joints & ERC's
Misc.:
T&P Lumpsum 9901 1.00 610.00 610.00
173,405.00
175,139.05
199,746.09
229,708.00
Cost for 1000 TRM 232,005.08
123050 Linking of track at level crossing locations as per RDSO drawings with any type of
rail section and sleeper on prepared formation including leading free rails/welded
panels avilable along the alignment on to formation,leading and spreading all fittings
and fastenings, spreading of sleepers at specified spacing, squaring ,placing of rails
over sleepers and fixing rails to sleepers with all types of fittings and fastenings to
correct gauge & alignment,excavating level crosing portion as necessary,fixing check
rails to running rails,providing C.C blocks,chairs, drilling holes to sleepers,fixing
dowels,anti corrosive painting to running rails and check rails,lubrication of fittings
and fastenings with contractor's grease as per IRPWM standards with contractors
labour, tools, consumables, with all lead, lifts etc. complete and raising, levelling and
initial packing of track to make it fit for 30 kmph and meet other prequisites
prescribed in Indidian Railway Track Machine Manual for deployment of Tamping
Machine.
Note:
1.Rail cutting and Hole drilling shall be paid seperately.

Material:
Labour:
(i) Carting of sleeper, Rails & fittings etc.

Code (Rs.) (Rs.)
(ii) Excavating the Level Crossing
(iii) Laying & spacing of sleeper (with greasing of pandrol clips)
(iv) Fixing rail,check rail, painting & fixing plate screws, etc.
(v) Initial packing with boxing of ballast
(vi) Fixing of LC Blocks etc.
Misc.:
T & P (Hydraulic Jacks, Crow bar, Beater, Wire claws, Rake ballast, Rail tounge etc.) Lumpsum 9901 1.00 92.00 92.00
16,547.00
16,712.47
19,060.57
21,919.66
Cost for 50 TRM 22,138.85
123060 Linking of BG track over ballasted deck bridges with any type of rail section and
PSC sleeper including leading free rails/welded panels avilable along the alignment
on to bridge, leading and spreading all fittings and fastenings, spreading of sleepers
at specified spacing, squaring, placing of rails over sleepers and fixing rails & guard
rails to sleepers with all types of fittings and fastenings to correct gauge &
alignment, lubrication of fittings and fastenings with contractor's grease as per
IRPWM standards with contractors labour, tools, consumables, with all lead, lifts etc.
complete and raising, levelling and initial packing of track to make it fit for 30 kmph
and meet other prequisites prescribed in Indidian Railway Track Machine Manual for
deployment of Tamping Machine.
Note:
1.Rail cutting and Hole drilling shall be paid seperately

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Leading & spreading of sleeper in proper spacing over bridge and
approches,leading guard rail and fixing them
(ii) Leading of rail, guard rails & fixing on sleeper, aligning etc.
(iii) For initial packing

Misc.:
T&P Lumpsum 9901 1.00 128.00 128.00
25,125.00
25,376.25
28,941.61

Code (Rs.) (Rs.)
33,282.86
Cost for 100 TRM 33,615.68
123070 Linking of track on Girder Bridge with Steel Channel/H-beam sleepers as per
approved drawings including leading of running and guard rails, sleepers and fittings,
bending of guard rails, notching, drilling of holes, cutting of rails etc. as per IRPWM
with latest correction slips and making track structure fit for normal speed.
Note:
1) Rails, Steel Channel/H-beam sleeper and all fittings will be supplied by Railways.
2)Transportation of track material if supplied beyond 250m of bridge appraches, shall
be paid seperately under relevant item.
Detail of cost for 50 TRM

Material:
Acetylene Gas (in cylinder) Kg 0341 65 4.00 260.00
Oxygen Gas (in cylinder) Kg 0340 50 12.00 600.00
Kerosene Oil Litre 0185 56 8.00 448.00
Normal unleaded Petrol Litre 0182 105 1.00 105.00
High Speed Hacksaw Blade of size 300mm x 12.5mm x 0.63mm (18TPI) as per as Nos. 0457 160 1.00 160.00
Labour:
(i) Leading Channel sleepers, running Rails & Guard Rails ,fittings over the bridge
and leading back the released rails & fittings to bridge approaches over the bridge

(ii) Fixing Channel sleepers alongwith fittings
(iii) Fixing rail with Fitting Clips
(iv) Fixing Guard rail
Mate (Skilled) Day 0002 609 1.00 609.00
Blacksmith - 1st Class (Skilled) Day 0008 609 2.00 1,218.00
Waterman (Un-skilled) Day 0034 431 1.00 431.00
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail tounge, Spanner etc.) Lumpsum 9901 1 116.00 116.00
Hire charges of Rail Cutting Machine Day 0142 300 0.50 150.00
Hire charges of Rail Drill Machine Day 0137 300 0.50 150.00
Hire charges for pillar drilling machine Day 0138 1000 0.50 500.00
18,574.30
18,760.04
21,395.83
24,605.20

Code (Rs.) (Rs.)
123080 Carrying out cut & connection to the existing PSC sleeper track under line block of
any rail section and sleeper density to connect the same to newly linked track which
is laid by the side, duly carrying out cutting of rails, insertion of additional PSC
sleepers, if required, providing fish plated joints including drilling of holes, slewing
required length of both tracks to prescribed alignment, adjusting sleeper spacing,
providing continuity to track, spreading of ballast to provide cushion, shoulder ballast
to the track stretch, giving one round of initial packing to make track fit for 20 kmph
speed and boxing of ballast to profile as directed by Engineer incharge.
Details of cost for 1 cut & connection

Material:
Labour:
(i) Opening of track & spreading of existing ballast on shiftted alignment.
(ii) For cutting,drilling holes & insertion of additional PSC sleepers
(iii) Slewing of both track for uniform alingment, adjusting of sleeper spacing,
insertion of ballast
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iii) One round packing, boxing etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
36,841.15
40,525.27
40,930.52
46,681.26
53,683.44
Cost for 1 cut & connection 54,220.28
Rate per cut & connection Each 54,220.28
123090 Shifting / Slewing the existing or newly assembled track of any rail section with any
type of sleepers and any density under line block to correct locations & alignment
and attending to one round kutcha packing to run safely at 20KMPH speed with all
contractors tools and consumables complete and as directed by Engineer in-charge.
123091 Maximum Shifting / Slewing upto 1 metre

Details of cost for 100 TRM (17 laborers for slewing + 13 laborers for packing &
ballast bed)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
12,993.00
13,122.93
14,966.70
17,211.71
Cost for 100 TRM 17,383.82
123092 Maximum Shifting / Slewing for more than 1 metre & upto 2 metres
Details of cost for 100 TRM (24 laborers for slewing + 14 laborers for packing &
ballast bed)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 80.00 80.00
15,595.00
15,750.95
17,963.96
20,658.55
Cost for 100 TRM 20,865.14
123100 Assembling, laying and linking of Broad Gauge track over Inspection Pit lines/CC
apron, RCC/CC Bed Blocks etc. to correct level & alignment, fixing of all fittings with
rails / panels, aligning & leveling correctly, as directed by engineer in-charge .Rate is
inclusive of cutting rails, drilling holes for fixing fish plates, lubrication of fittings &
fastenings, fixing reference pillars, arrangement for keeping assembly in correct
position while concreting, as required.
Details of cost for 500 TRM (i.e. 770 nos. Sleepers)

Material:
Labour:
(i) Spreading sleeper at specified spacings
Mate (Skilled) Day 0002 609.00 4.00 2,436.00


Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
(ii) Leading of rails & providing rails on sleepers with fixing all fittings etc.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iii) Fixing fish plate with Lubrication of MCI insert & ERC etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 238.00 238.00
69,553.30
70,248.83
80,118.79
92,136.61
Cost for 500 TRM 93,057.98
123110 Fixing all types of free rails / rail panels over pit line for BG track with inserts, elastic
rail clips, MS liners and grooved rubber pads below rail to correct spacing, gauge,
alignment and level with above fittings & fastenings in position, duly providing full
complements of rail fittings. Required nos. of inserts per bearing shall be fixed at the
time of concreting bed block over pit wall to correct spacing, centre to centre,
alignment & levels as per IR’s approved drawing.

Labour:
(i) Fixing rails over pit on RCC/bed block.
(ii) Correcting gauge, alignment & level
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Spanner, Hammer, beater, Rail tongue, Rake ballast etc.) Lumpsum 9901 1.00 36.00 36.00
9,086.00
9,176.86
10,466.21
12,036.14
Cost for 100 TRM 12,156.50
124000 4. Miscellaneous Works :

124010 Construction of Sanded Dead End as per RDSO’s Drawing no. RT-347 (with all
amendments) with brick-work using country bricks or CC bricks in mud mortar and
filling with river coarse sand, surrounding rails and filling around.
Note: Cost of brick and sand will be paid separately.
Details of cost for 1 dead end


Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 28.00 28.00
6,923.00
6,992.23
7,974.64
9,170.83
Cost for I dead end 9,262.54
Rate per dead end Each 9,262.54
124020 Working of the Railway Push Trolley by arranging one Head trollyman along with 3
trollymen as per Railway's rules and stipulations for conducting inspections by
Railway officials and as directed by Engineer in-charge.
Note:
1) Labourers supplied should be of skilled in case of head trollyman and semiskilled
in case of trollymen and capable of pushing trolley in all gradients, and levels duly
observing all safety precautions as per the manual.
2) The labour engaged should be physically fit for strenous work and literate.
124021 For Full day (8 hrs )

Details of cost for full day.
Labour:
Head Trolley man (Skilled) Day 0036 609.00 1.00 609.00
Trolly man (Semi-skilled) Day 0037 505.00 3.00 1,515.00
Misc.:
T & P (5% with contingency) Lumpsum 9901 1.00 45.00 45.00
2,169.00
2,190.69
2,498.48
2,873.25
Cost for full day 2,901.99
Rate per day Each 2,901.99
124022 For Half day (4 hours)

Details of cost for half day.
Labour:
Head Trolley man (Skilled) Day 0036 609.00 1.00 609.00
Trolly man (Semi-skilled) Day 0037 505.00 1.50 757.50
Misc.:
T & P (5% with contingency) Lumpsum 9901 1.00 30.00 30.00
1,396.50
1,410.47
1,608.64
1,849.93

Code (Rs.) (Rs.)
Cost for half day 1,868.43
Rate per Half-Day Each 1,868.43
124030 Providing Caution Watchman with prescribed protection equipments at a location

where caution order is imposed and ensuring to be on continuous vigil and exhibit
necessary hand signals to the trains for their passage over caution spot.
Note:
1) Detonators, Banner flags and HS flags will be supplied by Railways. Contractor
has to provide 3 cell electric torch and tricolor light;
2) If Contractor fails to post watchman at any time during one day, penalty at double
the accepted rates will be levied and
3) The watchman nominated by the contractor will be screened for suitability as per
Railway norms.
124031 For one shift ( 12 Hrs)

Details of cost for one Shift 1 man required)
Labour:
Caution man (Semi-skilled) Day 0038 505.00 1.50 757.50
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
777.50
785.28
895.61
1,029.95
Cost for per day & night 1,040.25
Rate per Shift Each 1,040.25
124032 For Half Shift (4 hours)

Details of cost for Half Shift
Labour:
Caution man (Semi-skilled) Day 0038 505.00 0.50 252.50
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
262.50
265.13
302.38
347.73
Cost for Half Shift 351.21
Rate per Half-Shift Each 351.21

Code (Rs.) (Rs.)
124040 Preparation of completion drawings of yard in Autocad, showing all the details, such
as circulating area, approach road, platform shelter, platform, FOB etc., showing
relevant particulars to appropriate scale as per IR's Engineering Code on approved
quality, transparent media as per details supplied by Railways, including submission
of check print for proof checking, duly incorporating the suggested corrections and
modifications and supplying the final plot on approved quality & transparent media
with six copies of ammonia prints complete and soft copy, as directed by Engineer in-
charge
Note:
(i) Drawings shall be prepared by using latest drawing making softwares AutoCad,
Work station etc. and printing shall be done on high end latest plotters.
(ii) Stage Payment - (a) For check print - 40% (b) For Paper tracing - 40% (c) For
Ammonia print & soft copy - 20%.
124041 Completion drawing of yard at junction station

Material:
Tracing paper in roll with specification- weight 95gm/m2 width 914mm and length Each 0502 250.00 0.30 75.00
45.7m
Ammonia Print Sheet of 55 to 60 GSM, 914mm wide and 10m long Each 0503 250.00 0.40 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
5,015.00
5,065.15
5,776.80
6,643.32
Rate per Yard Each 6,709.76
124042 Completion drawing of building

Material:
45.7m
Labour:
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
3,525.00
3,560.25
4,060.47
4,669.53
Rate per building Each 4,716.23

Code (Rs.) (Rs.)
124043 Completion drawing of land plan
Details of cost for 1 Kilometer
Material:
45.7m
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
3,495.00
3,529.95
4,025.91
4,629.79
Cost for 1 Kilometer 4,676.09
Rate per km Km 4,676.09
124044 Completion drawing of way side station

Material:
45.7m
Labour:
Misc.:
T&P Lumpsum 9901 1.00 25.00 25.00
1,975.00
1,994.75
2,275.01
2,616.26
Rate per Station Each 2,642.43
124050 Dismantling / removing the existing bearing plate and fixing new bearing plates
supplied by Railways in pit lines, duly breaking / chiselling CC to required depth, so
as to fix new bearing plates etc. with all contractor's labour, tools, lead, lift,
transportation etc. including crossing of tracks complete and as directed by Engineer
in-charge (concrete work for fixing will be paid separately)
Detail of cost for 40 no's bearing plate

Labour:
Misc.:
T&P Lumpsum 9901 1.00 100.00 100.00
Hire charges of Hammer Breaker Day 0148 200.00 1.00 200.00
1,845.00

Code (Rs.) (Rs.)
1,863.45
2,125.26
2,444.05
Cost for 40 no's bearing plate 2,468.49
Rate per bearing plate Each 61.71
Draft IR Unified Standard Analysis of Rates - 2021 Chapter - 13: Maintenance Activities
CHAPTER - 13 : Maintenance Activities

Code (Rs.) (Rs.)
131000 1. Through Packing Works :
131010 Through packing of track, as per procedure prescribed in latest edition of Indian
Railways Permanent Way Manual
For PSC sleeper Track
131011 For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more
Details of cost for 156 TRM (1 Person will do Through packing 12 sleepers of 1540
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P ( Crow bar,Wire claws, Rake ballast, Hydraulic jacks, Gauge cum level,Shovel Lumpsum 9901 1.00 120.00 120.00
etc.)
10,211.00
10,313.11
11,762.10
13,526.42
Cost for 156 TRM Sleepers 13,661.68
131012 For PSC sleeper Track with Sleeper Density of less than 1540 Sleepers/Km
Details of cost for 180 TRM ( 1 Person will do Through packing 12 sleepers of 1340
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Beater, Wire claws, Rake ballast, Hydraulic jacks etc.) Lumpsum 9901 1.00 40.00 40.00
10,131.00
10,232.31
11,669.95
13,420.44
Cost for 180 TRM Sleepers 13,554.65
For other than PSC Sleeper Track :

131013 For other than PSC Sleeper Track with Sleeper Density of 1540 Sleepers/Km or
more
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
10,211.00
10,313.11

Code (Rs.) (Rs.)
11,762.10
13,526.42
Cost for 182 TRM 13,661.68
131014 For other than PSC Sleeper Track with Sleeper Density of 1340 Sleepers/Km (M+4)
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
10,562.00
10,667.62
12,166.42
13,991.38
Cost for 209 TRM 14,131.30
131020 Picking up of slacks in track, as directed by Engineer in-charge duly opening up

ballast, gauging, alignment, correcting longitudinal & cross levels, packing, boxing of
ballast and dressing the same under traffic conditions as per procedure prescribed in
latest edition of IRPWM.
Note: In-charge section Engineer should identify locations requiring packing and
obtain prior approval of DEN/XEN before execution of the work when there is no
Zonal Track Maintenance agency deployed in the section.
131021 For PSC Sleeper

Details of cost for 182 TRM (1 Person will do Picking up of slacks 14 sleepers of
1540 density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
10,211.00
10,313.11
11,762.10
13,526.42
Cost for 182 TRM 13,661.68
131022 For other than PSC Sleeper

Details of cost for 208 TRM ( 1 Person will do Picking up of slacks 16 sleepers of
1540 density in a day)
Labour:

Code (Rs.) (Rs.)
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bars, beater, Wire claws, Cross level etc.) Lumpsum 9901 1.00 40.00 40.00
10,131.00
10,232.31
11,669.95
13,420.44
Cost for 208 TRM 13,554.65
131030 First or Second Through Packing of track for all sleeper density including giving a
general lift, as desired to eliminate sag after Deep Screening work, lifting of track,
lowering of track and major realignment of curves and formation rehabilitation as per
procedure prescribed in latest edition of IRPWM.
Note: General lift is normally 25 mm and isolated lift may be upto 50 mm.
131031 For PSC Sleeper Track with Sleeper Density of 1540

density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
10,211.00
10,313.11
11,762.10
13,526.42
Cost for 130 TRM 13,661.68

Rate 10% extra over item no. 131031
Rate per TRM TRM 131031 105.09 1.10 115.60

Rate 20% less than item no. 131031
Rate per TRM TRM 131031 105.09 0.80 84.07

Code (Rs.) (Rs.)
131034 For other than PSC Sleeper Track with Sleeper Density of 1540
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
10,131.00
10,232.31
11,669.95
13,420.44
Cost for 156 TRM 13,554.65
Rate per TRM TRM 131034 86.89 1.10 95.58
Rate per TRM TRM 131034 86.89 0.80 69.51
131040 Third or subsequent Through Packing of track for all sleeper density including
picking of slacks, as required after second through packing, subsequent to Deep
Screening work as per procedure prescribed in latest edition of IRPWM.This item can
also be used after lifting/regrading/realignement works also.
Note: General lift is normally 25 mm and isolated lift may be upto 50 mm.

density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
10,211.00
10,313.11
11,762.10
13,526.42
Cost for 169 TRM 13,661.68

Rate per TRM TRM 131041 80.84 1.10 88.92


Code (Rs.) (Rs.)
Rate per TRM TRM 131041 80.84 0.80 64.67
density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
10,131.00
10,232.31
11,669.95
13,420.44
Cost for 195 TRM 13,554.65
Rate per TRM TRM 131044 69.51 1.10 76.46
Rate per TRM TRM 131044 69.51 0.80 55.61
131050 Through packing of points and crossings, derailing switches including gauging,
fittings recoupment, elimination of sag and to the required alignment after Deep
Screenining as per procedure prescribed in latest edition of IRPWM complete as per
direction of Engineer-in-charge.
Note: This work shall be operated in exceptional cases with written approval at DEN
level when UNIMAT is not availble and immediate packing is required to maintain
safety.
131051 1 in 8½ PSC layout

Details of cost for one set
Total length is 28.54 metre (approx.), For Through packing Sleeper no. 1 to 13 ( 2
persons), Sleeper no. 14 to 66 ( 53 sleepers @ 5 sleepers/person i.e. 11 persons)
including filling ballast in the packing zone and operation of mechanical jack as
required.
Labour:
(i) For opening, packing & aligning of track
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
7,194.00
7,265.94
8,286.80
9,529.83

Code (Rs.) (Rs.)
131052 1 in 12 PSC layout

Total length is 39 metre (approx.), For Through packing Sleeper no. 1 to 20 (3
persons), Sleeper no. 21 to 95 (75 sleepers @ 5 sleepers/person i.e. 15 persons)
required.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
9,354.00
9,447.54
10,774.92
12,391.16
131053 1 in 16 PSC layout

Total length is 54.50 metre (approx.), For Through packing Sleeper no. 1 to 22 (4
persons), Sleeper no. 23 to 106 ( 83 sleepers @ 5 sleepers/person i.e. 17 persons)
required.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
etc.)
10,672.00
10,778.72
12,293.13
14,137.10
131054 1 in 8½ Derailing Switch

Total length is 9.00 metre and 13 sleepers needing 2 labour.
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
Misc.:
1,026.25

Code (Rs.) (Rs.)
1,036.51
1,182.14
1,359.46
131055 1 in 12 Derailing Switch

Total length is 13.00 metre (approx.) and 20 sleepers needing 3 persons with
mechanical jack.
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
Misc.:
1,461.25
1,475.86
1,683.22
1,935.70
131060 Packing of isolated loose PSC sleepers on plain track below the bottom of the
sleepers and surrounding through out its length duly opening two galas on either side
of the renewed sleepers and packing the sleeper to bring the track to normal speed
including gauging, aligning, squaring of sleepers and sectioning of ballast to the
required profile with all contractor's labour, tools and plant etc. including all lead and
lift and crossing of tracks where ever necessary complete and as directed by the
Engineer-in-charge.
Rate analysis for 80 sleepers

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Hammer, Jack, spanner, mortar pan etc.) Lumpsum 9901 1.00 10.00 10.00
4,067.00
4,107.67
4,684.80
5,387.52
Cost of 80 sleepers 5,441.39
131070 Slack picking of joint sleepers and 3 approach sleepers on either sides giving
required lift to make up general track level, packing and profiling as directed.
Details of cost for 30 Joints.( One group of two persons will do 3 joints in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T & P ( Crow bar, Beater, Wire claws, Rake ballast, jack etc.) Lumpsum 9901 1.00 42.00 42.00
10,638.00
10,744.38
12,253.97
14,092.06
Cost for 30 Joints. 14,232.98
Rate per Joint. Each 474.43
132000 2. Systematic Overhauling Works :

132010 Shallow Screening of existing ballast under traffic as per procedure prescribed in
latest edition of IRPWM , including removing the crib ballast in 50mm to 75mm depth
below bottom of sleeper and complete shoulder ballast without breaking core under
the bottom of sleeper, to recover clean ballast by screening on wire mesh and
disposing off the muck including throwing & leveling, if required beyond minimum 5m
from the edge of cutting which are upto 3m deep or alternatively carting it upto 50m
for disposing it off beyond cutting or platforms away from the track, as directed by
Engineer in-charge including cutting & making up the cess and ensuring proper
drainage slope and then re-inserting cleaned ballast into track and compaction of
shoulder and crib ballast by wooden mallet and dressing / profiling ballast as per
railway specifications.
For PSC sleeper Track :

132011 For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more
Details of cost for 91 TRM ( 7 sleeper per head sleeper density of 1540 sleepers/km)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For shallow screening works:
(ii) Other Works, e.g. removal/spreading of muck, replacing rounded ballast,
recouping deficient ballast & cess attention etc. (@ one man per 13 TRM) :
Misc.:
T & P (Beater, Wire claws, Rake ballast, Pan iron mortar, Hydraulic jacks etc.) Lumpsum 9901 1.00 54.00 54.00
13,162.00
13,293.62
15,161.37
17,435.58
132012 For PSC sleeper Track with Sleeper Density less than 1540 sleepers/Km
Details of cost for 120 TRM ( 8 sleeper per head sleeper density of 1340
sleepers/km)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
14,028.00
14,168.28
16,158.92
18,582.76
Cost for 120 TRM 18,768.59
For other than PSC sleeper Track :

132013 For other than PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more
(M+7)
sleepers/km)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
13,595.00
13,730.95
15,660.15
18,009.17
Cost for 104 TRM 18,189.26
132014 For other than PSC sleeper Track with Sleeper Density of 1340 sleepers/Km (M+4)
sleepers/km)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,461.00
14,605.61
16,657.70

Code (Rs.) (Rs.)
19,156.35
Cost for 135 TRM 19,347.92
132015 Extra over Items 132011 to 132014 for working in yards

Details of cost for 150 TRM ( 1 extra man provided for 15 track metre length for
working in yard)
Labour:
(i) For shallow screening & removal of muck :
Misc.:
4,330.00
4,373.30
4,987.75
5,735.91
132020 Systematic Overhauling (shallow screening) of fish plated / welded joint track
sleepers including 3 approach sleepers on either sides upto 50mm below bottom of
sleepers in crib & shoulder, replacing rounded ballast, recouping deficient ballast
within 50m lead, replacement of worn-out fittings supplied by Railway, as directed as
per procedure prescribed in latest edition of IRPWM.
Details of cost for 16 Joints. ( One group of four persons will do 4 joints in a day)
Labour:
(i) For shallow screening of joint sleepers including 3 approach sleepers:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(ii) For recoupment of ballast:
Misc.:
T & P (Crow bar, Beater, Wire claws,Wire basket, Rake ballast, Hydraulic jacks, off Lumpsum 9901 1.00 60.00 60.00
track tamper etc.)
12,737.00

Code (Rs.) (Rs.)
12,864.37
14,671.81
16,872.59
133000 3. Pulling Back & End Cropping Works :

133010 Pulling back of rails / panels on running track for creep adjustment or other incidental
activities by removing and re-fixing all the fittings,and fastenings including squaring of
sleepers and slack picking of displaced sleepers, as directed.
133011 For rails of 13 metre length

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
T & P (Spanner, Rail tounge, Hammer, Crow bars, Tami bar, beater, Wire claws, Lumpsum 9901 1.00 68.00 68.00
etc.)
16,875.00
17,718.75
17,895.94
20,410.32
23,471.86
Cost for 1000 RM. 23,706.58
133012 For rails from 13 metre & upto 40 metre length

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
etc.)
19,040.00
19,992.00
20,191.92
23,028.88
26,483.22
Cost for 1000 RM. 26,748.05

Code (Rs.) (Rs.)
133013 For rails more than 40 metre length

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
etc.)
21,205.00
22,265.25
22,487.90
25,647.45
29,494.57
Cost for 1000 RM. 29,789.52
133020 Pulling of single rail / welded rail panels to create a specified gap under traffic block,
including opening of fittings & fastenings and re-fixing them on track after pulling of
rail and creating standard gap for welding.
133021 For Rails more than 13m and upto 40m length
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
6,053.00
6,355.65
6,419.21
7,321.11
8,419.27
Cost for 300 RM 8,503.46
133022 For Rails more than 40m length

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 28.00 28.00
7,785.00
8,174.25
8,255.99
9,415.96
10,828.35
10,936.64
Cost for 300 RM 10,936.64
134000 4. Re-Alignment of Curves :

134010 Slewing and realigning of curves under traffic line block condition, as directed by
Engineer in-charge with contractor's labour,tools&plants, as required with general lift
upto 25mm including one round of through packing, loosening/tightening of P.Way
fittings, if required and other incidental works.
Note: Payment will be made based on average slew calculated in each 50m length of
track by averaging absolute values of positive and negative value of slews.
134011 Other than PSC Sleeper track - Maximum slew upto 50mm
Details of cost for 390 TRM ( 1 Person will do Through packing including slewing 12
sleepers of 1540 density in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 100.00 100.00
23,552.00
25,907.20
26,166.27
29,842.63
34,319.03
Cost for 390 TRM 34,662.22
134012 Other than PSC Sleeper track - Maximum slew more than 50mm and upto 100mm
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
T&P Lumpsum 9901 1.00 112.00 112.00
26,150.00

Code (Rs.) (Rs.)
28,765.00
29,052.65
33,134.55
38,104.73
Cost for 364 TRM 38,485.78
134013 Other than PSC Sleeper track - Maximum slew more than 100mm and upto 150mm
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 116.00 116.00
27,016.00
29,717.60
30,014.78
34,231.85
39,366.63
Cost for 338 TRM 39,760.30
134014 Other than PSC Sleeper track - Maximum slew more than 150mm
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 120.00 120.00
27,882.00
30,670.20
30,976.90
35,329.16
40,628.53
Cost for 312 TRM 41,034.82
134015 PSC Sleeper track - Maximum slew upto 50mm


Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 96.00 96.00
22,255.00
24,480.50
24,725.31
28,199.21
32,429.09
Cost for 312 TRM 32,753.38
134016 PSC Sleeper track - Maximum slew more than 50mm and upto 100mm
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 110.00 110.00
25,717.00
28,288.70
28,571.59
32,585.89
37,473.78
Cost for 286 TRM 37,848.52
134017 PSC Sleeper track - Maximum slew more than 100mm and upto 150mm
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 116.00 116.00
27,016.00
29,717.60
30,014.78

Code (Rs.) (Rs.)
34,231.85
39,366.63
Cost for 260 TRM 39,760.30
134018 PSC Sleeper track - Maximum slew more than 150mm

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 120.00 120.00
27,882.00
30,670.20
30,976.90
35,329.16
40,628.53
Cost for 234 TRM 41,034.82
135000 5. Destressing Works :

135010 De-stressing of LWR/CWR track of any density under traffic line block with
contractor's labours, tools, equipments and consumables inclusive of all lead & lift.
Activities include cutting of LWR/CWR into convenient panels of specified length,
removal of ERCs, liners, greasing of ERCs and liner contact area, lifting rails and
keeping them on rollers provided at every 15 sleepers, working out elongation of rail
ends depending on prevailing site conditions, pulling rails with the help of Hydraulic
Tensor to achieve the desired elongation, cutting rails, as required, removing rollers
and placing rail in position, re-fixing ERCs & liners and adjustment of gap at SEJs :
Note:
(1) Welding of rail joints will be paid separately.
(2) Rail cutting and Hole drilling shall be paid separately.
(3) Opening and closing of LC if required will be paid separately.
(4) As per procedure prescribed in latest edition of IRPWM & CE's Circulars for
destrssing of LWR/CWR, if any.
135011 With Railway’s Hydraulic Rail tensor

Details of cost for 1000 TRM ( 3 Persons deputed in between 100 Track Metre
length )
Material:
For greasing of ERCs and liner contact area of 1 sleeper required 35 gram grease
graphite.( Cost for 1660 sleeper/Km )
Labour:
(i) For removal of ERCs, lifting the rails and keepping them on rollers, greasing and
refixing of fastenings after destressing.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00

Code (Rs.) (Rs.)
(ii) Additional labour for operating Rail Tensor
Misc.:
T & P (Rail tounge, Crow bars, Hammer, Beater, etc.) Lumpsum 9901 1.00 132.00 132.00
32,959.00
33,288.59
37,965.64
43,660.48
Cost for 1000 TRM 44,097.09
135012 With Contractor’s Hydraulic Rail tensor

Details of cost for 1000 TRM ( 3 Persons deputed in between 100 Track Metre length
)
Material:
Labour:
refixing of fastenings after destressing.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(ii) Additional labour for operating Rail Tensor
Misc.:
Hire charges of Hydraulic Rail tensor Day 0146 150.00 4.00 600.00
34,227.00
34,569.27
39,426.25
45,340.19
Cost for 1000 TRM 45,793.59
135013 Without Rail tensor

Details of cost for 1000 TRM ( 3 Persons deputed in between 100 Track Metre length
)
Material:
Labour:
refixing of fastenings after destressing. 2persons extra for hamerring rails by wooden
mallet.
Mate (Skilled) Day 0002 609.00 2.00 1,218.00

Code (Rs.) (Rs.)
Misc.:
31,929.00
32,248.29
36,779.17
42,296.05
Cost for 1000 TRM 42,719.01
135020 Providing temporary Buffer Rails of fish plated joints of 3 pairs, measuring 6.5m each,
duly removing rails of the existing track including cutting & drilling of rails as required
for isolating LWR/CWR on all types of track structure. Work will be done under traffic
block condition.
Note:
1.Each set comprises of 3 pairs of rails 6.5 m long only.
2.Only Rails fish plate and fish bolts will be supplied free by Railway within free lead
of 250m.
Details of cost for each set

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
6,515.08
7,166.58
7,238.25
8,255.22
9,493.51
Cost for each set 9,588.44
136000 6. Renewal and Miscellaneous Works :

136010 Fixing Joggled Fish Plates with bolt / clamp (supplied by Railway) in running track
conditions at welds on rail, as directed by engineer in-charge (drilling of holes in rail,
if required, shall be paid separately).

Code (Rs.) (Rs.)
136011 With 2 bolts
Labour:
(i) Fixing of Joggled Fish Plate.
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Spanner, Hammer, Crow bars, Tami bari etc.) Lumpsum 9901 1.00 12.00 12.00
2,776.00
2,803.76
3,197.69
3,677.34
Rate per set Set 92.85
136012 With 4 bolts

Labour:
(ii) Fixing of Joggled Fish Plate.
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
3,084.50
3,115.35
3,553.05
4,086.01
136013 With Clamps

Labour:
(ii) Fixing of Joggled Fish Plate.
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
3,948.50
3,987.99
4,548.30
5,230.54

Code (Rs.) (Rs.)
136020 Providing wooden blocks under rail joints duly transporting Railway’s released
wooden blocks, providing bearing plate with rail screw / dog spikes and doing
packing, as directed under traffic condition.
Note: Wooden blocks, Bearing plates, rail screws/dog spikes will be supplied free at
SSE/P.Way depot
Detail of cost for 50 joints

Material:
Auger Carpenter Each 0471 90.00 3.00 270.00
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bars, Hammer, Beater, Wooden Saw, etc.) Lumpsum 9901 1.00 100.00 100.00
5,541.00
5,596.41
6,382.71
7,340.11
Rate per joint Each 148.27
136030 Removing the existing wooden blocks under each joint, duly removing fittings,
transporting and stacking material wise in a countable manner and handing over the
wooden blocks & fittings at PWI's Depot or as directed by Engineer incharge.

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
4,376.50
4,420.27
5,041.31
5,797.51
Cost for 150 nos.joints 5,855.48
Rate per joint Each 39.04
136040 Maintenance of track on main line & loops, Points & crossings etc. including special
attention to section for carrying out various maintenance works listed in Indian
Railways P.Way Manual / Bridge Manual for safe running of goods and passenger
trains with contractor's tools / labours etc. complete, as directed by Engineer in-
charge.
Note: Contractor shall arrange one gang at any point of time comprising of minimum
specified labours with sufficient experience in P.Way working.

Code (Rs.) (Rs.)
136041 One Gang comprising of 15 labours plus 1 Mate.
Note: In case, contractor provides less no. of Labour/Mate, payment will be deducted
for each such person @ 15% of the accepted item rate.
Details of cost for per day per Gang of 15 labours

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.
T & P (Hydraulic Jack, Crow bars, Wire claws, Rake ballast, Rail cutting machine Lumpsum 6465.00 5% 323.25
etc. @ 5% of the cost of labour
7,397.25
7,471.22
8,520.93
9,799.07
Rate per day per Gang Gang Day 9,897.06
136042 One Gang comprising of 20 labours plus 1 Mate.

Note: In case, contractor provides less no. of Labour/Mate, payment will be deducted
for each such labour @ 10% of the accepted item rate.
Details of cost for per day per Gang of 10 labours

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Hydraulic Jack, Crow bars, Wire claws, Rake ballast, Rail cutting machine Lumpsum 8620.00 5% 431.00
etc. @ 5% of the cost of labour
9,660.00
9,756.60
11,127.40
12,796.51
Rate per day per Gang Gang Day 12,924.48
136050 Interchanging gauge face of rails of any section in traffic line block including removal
of fittings and re-fixing the same after changing of gauge face, cutting of rails, joining
the rails with fish plate & drilling holes as directed by engineer in-charge.

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P ( Crow bars, beater, Wire claws, Hammer, Spanner etc.) Lumpsum 9901 1.00 68.00 68.00

Code (Rs.) (Rs.)
17,636.00
19,399.60
19,593.60
22,346.50
25,698.47
Cost for 260 TRM 25,955.46
136060 Replacing existing glued joint rail with cut rails or with glued joint rail or insertion of
glued joint by cutting existing track under traffic condition by cutting rails, refixing with
all rail sleeper fastenings and providing required gaps for carrying out welding as an
alternative to drilling holes or joining rails with fish plates duly drilling holes as
required and as directed by engineer in-charge.
Note:
(1) Drilling holes & rail cutting will be paid separately.
(2) Transportation of materials to the site of work from supply points, if more than
250m, shall be paid separately.
Details of cost for 4 joints

Material:
Labour:
For leading of rail, replacement of glued joint & carting released glued joints back

Misc.:
T&P Lumpsum 9901 1.00 16.00 16.00
4,147.00
4,561.70
4,607.32
5,254.65
6,042.84
136070 Fixing of wooden distance pieces for platforms with contractor's labour, tools and
plants of size Wooden Block (size : 1.0m x 0.3m x 0.15m)
136071 With Railway’s wooden block (by cutting Railway’s wooden sleepers into blocks by
sawing to size)
Labour:
(i) Cutting of wooden blocks from sleepers ( 1 carpenter + 1 helper prepare 20 Blocks
in a day )
Carpenter (Skilled) Day 0006 609.00 3.00 1,827.00
(ii) Fixing of wooden blocks
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
8,006.50

Code (Rs.) (Rs.)
8,086.57
9,222.73
10,606.14
Rate per distance piece Each 178.54
136072 With Contractor’s hard wood block

Material:
Volume of 1 no. Wooden Block (size : 1.20m x 0.3m x 0.15m) = 0.054 cum
Volume for 60 nos. = 60 x 0.054 cum = 3.24 cum = 3240 Cudm
Labour:
(i) Fixing of wooden blocks
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
119,152.50
120,344.03
137,252.36
157,840.21
Cost for 60 nos 159,418.62
Rate per distance piece Each 2,656.98
136080 Drilling holes of 16mm to 22mm dia. on all types of PSC sleepers and fixing the
dowels with adhesive of approved quality for fixing check rails & guard rails, as
directed by engineer in-charge
Details of cost for 60 holes
Material:
Drill twist made of high speed steel for size 18mm dia of Addison / I T make Each 0467 1866.40 1.00 1,866.40
HDPE Dowels Each 0456 100.00 60.00 6,000.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
Hire charges of Concrete Sleeper Drilling Machine Day 0140 300.00 1.00 300.00
12,537.40
12,662.77
14,441.89
16,608.18

Code (Rs.) (Rs.)
136090 Cleaning of side drains along the track including disposing of muck beyond Railway
boundary as per instructions of Engineer in-charge to keep drains clean and clear in
cuttings etc.
Details of cost for 500 RM ( One group of two persons will clean 50 Running metre
in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
10,131.00
10,232.31
11,669.95
13,420.44
Cost for 500 RM 13,554.65
136100 Removing weeds & bushes in ballast section and cess upto 3.95m from centre line
of track in mid section & station yard, as specified by Engineer in-charge including
disposal of branches, bushes outside cess/yard.
Details of cost for 1040 TRM ( One persons will Remove weeds & bushes 52
Running metre in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
9,700.00
9,797.00
11,173.48
12,849.50
Cost for 1040 RM 12,978.00
136110 Trimming of tree branches coming within 4m of centre line of track & those
obstructing views of Curves/LCs / Signal / Indicator at locations in section & station
yard, as specified by Engineer in-charge including disposal of branches, bushes
outside cess/yard.
Note: Girth of more than 30 cm will only be considered as tree branch.
Details of cost for 50 Tree branches

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
5,370.00

Code (Rs.) (Rs.)
5,423.70
6,185.73
7,113.59
Cost for 50 Tree branches 7,184.73
Rate per tree branch Each 143.69
136120 Making kutcha trapezoidal side drain of bottom width as 300mm and depth of 450mm
in cutting section by excavation in all types of soil including utilising excavated muck
for dressing of cess, slopes etc. in Railway land.
Details of cost for 100 RM (One group of two persons will make kutcha traezoidal
side drain of bottom width 300mm and depth of 450mm, 6.25 Running metre in a
day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
14,896.00
15,044.96
17,158.78
19,732.59
Cost for 100 RM 19,929.92
136130 Patrol man for patrolling during cold / hot weather on track for protecting track with all
contractor’s labour, tools, plants etc. complete as directed by Engineer In charge.
Note:
1.The person deployed for patrolling must have the following items:
• Valid certificate of competency issued by Railways.
• Medical certificate issued by Railway fit for A-3 medical category.
2.The following equipment will be supplied by Railways for each patrolman and same
to be handed over back to Railways in good condition:
• Detonators – 10 nos. if used, bursted detonators to be handed over back and report
with reasons for use.
• Tri colour Torch – 1no.
• Equipment list to be supplied by railway to be mentioned.
• Canne –a - boule(if required)
3.The following equipment to be arranged by contractor for each patrol man:
H.S.Flags green-1 No (Std size),H.S Flags -Red-2 Nos(Std size),Torch light 3 cell-1
no, Staff for flags-1no,Whistle Thunder- 1no,Protective clothing to withstand climate,
Gum boots, Haver sack.
136131 For duration of 8 hrs.

Details of cost for 2 Persons
Labour:
Patrolman (Semi-skilled) Day 0035 505.00 2.00 1,010.00
Misc.:
T & P Rs.10 per day and (Rs.25 for contingency+ Rs.5 for training) per man per day Lumpsum 9901 1.00 70.00 70.00
1,080.00
1,090.80

Code (Rs.) (Rs.)
1,244.06
1,430.67
Cost for 2 Persons 1,444.97
Rate per Person Each 722.49
136132 For 12 hrs. duration

Details of cost for 24 Hrs @ 1 person 12 Hours i.e 2 Persons for 24hrs { Take 3
person for 24 hrs}
Labour:
Misc.:
1,595.00
1,610.95
1,837.29
2,112.88
Cost for 24 Hours for 2 Persons, @ 1 person 12 Hours i.e 2 Persons for 24hrs 2,134.01
Rate per Person Each 1,067.01
136140 Patrol man for monsoon / security patrolling whenever required for protection of track
with all contractor’s labour, tools and plants etc. complete and as directed by
Engineer in-charge and as per IRPWM (for a duration of 12 hours)
Note:
1.The person deployed for patrolling must have the following items:
• Valid certificate of competency issued by Railways.
• Medical certificate issued by Railway fit for A-3 medical category.
2.The following equipment will be supplied by Railways per each patrol man and
required to be handed over back to Railways in good condition:
• Detonators – 10 nos.(in a tin case), if used, bursted detonators to be handed over
back with reasons for use.
• Tri Colour Torch - 1no.
• Patrol chart.
• Patrol book.
3.The following equipment to be arranged by contractor for each patrol man:

• H.S.flags green – 1no.(standard size)
• H.S. flags red – 2nos. .(standard size)
• Torch (3 cell) – 1no.
• Staff for flags – 1no.
• Whistle thunder – 1no.
•Protective cloth to withstand the climate
•Gum boots
•Haver sack
4. Wherever 2 or more tracks are parallel with in track centres 50m. one patrol man
will be sufficient.
• Wherever the track centers are more than 50m. Separate patrol man to be
deputed for each track & extra payment will be made for such case.
5. Route KM means including both UP & DN.
136141 For Day shift

Details of cost for 1 Person
Labour:
Patrolman (Semi-skilled) Day 0035 505.00 1.00 505.00
Misc.:
540.00

Code (Rs.) (Rs.)
545.40

Code (Rs.) (Rs.)
622.03
715.33
Cost for 1 Person 722.49
136142 For Night shift

Details of cost for 2 Person
Labour:
Considering 25% extra wages for night duty
Misc.:
1,342.50
1,355.93
1,546.43
1,778.40
Cost for 2 Persons 1,796.18
137000 7. Marking and Painting Works :

137010 Painting of rail outside track on rail bottom, web, foot and fishing plane as per
requirement with one coat of red oxide / zinc chromate primer to IS : 2074 of reputed
make including surface preparation, i.e. cleaning with wire brush / sand paper as a
complete job
Details of cost for 130 RM ( One group of 1 Painter + 1 helper + 1 Labour will paint
65 RM i.e 5 Rails of 13 metre in a day)
Material:
Zinc Chromate red oxide Primer to IS:2074 Litre 0308 130.00 30.00 3,900.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 12.00 60.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
5,653.00
5,709.53
6,511.72
7,488.48
Cost for 130 RM 7,563.36
137020 Painting of rail on running track on rail, web, foot including liner contact area
(excluding bottom of foot) and fishing plane as per requirement with one coat of red
oxide / zinc chromate primer to IS : 2074 of reputed make including surface
preparation, i.e. cleaning with wire brush / sand paper as a complete job.

Code (Rs.) (Rs.)
Details of cost for 130 RM ( One group of 1 Painter + 1 helper + 1 Labour will paint
65 RM i.e 5 Rails of 13 metre in a day)
Material:
Zinc Chromate red oxide Primer to IS:2074 Litre 0308 130.00 20.00 2,600.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
4,764.00
4,811.64
5,487.68
6,310.83
Cost for 130 RM 6,373.94
137030 Anti-corrosive painting of rail outside track on rail bottom, web, foot and fishing
plane as per requirement with two coats of thickness of 100 microns each by
bituminous black paint confirms to IS-9862 of reputed make including surface
preparation, i.e. cleaning with wire brush / sand paper as a complete job as per
procedure prescribed in latest edition of IRPWM.
137031 For 60 Kg Rails

Details of cost for 104 RM (One group of 1 Painter + 1 helper + 1 Labour will paint
two coat 52 RM i.e 4 Rails of 13 metre in a day)
Material:
Anti-corrosive Bituminous Paint (Black) confirming to IS:9862 Litre 0304 80.00 40.00 3,200.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 12.00 60.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
5,488.00
5,542.88
6,321.65
7,269.90
Cost for 104 RM 7,342.60

Considering cost reduction of 11.15% in the rate for 60Kg
Rate per RM RM 137031 70.60 0.89 62.73

Code (Rs.) (Rs.)
137040 Anti-corrosive painting of rail on running track of any sleeper density on web, foot
etc. including liner contact area (excluding bottom of foot) and fishing plane as per
requirement with two coats of thickness of 100 microns each by bituminous black
paint confirms to IS-9862 of reputed make including painting of liners, ERCs and
including surface preparation, i.e. cleaning with wire brush / sand paper as a
complete job as per procedure prescribed in latest edition of IRPWM
Note: 60% of payment shall be made if painting on one is done only gauge face side
is done.

Details of cost for 104 RM (One group of 1 Painter + 1 helper + 1 Labour will paint
two coat 52 RM i.e 4 Rails of 13 metre in a day)
Material:
Anti-corrosive Bituminous Paint (Black) confirming to IS:9862 Litre 0304 80.00 30.00 2,400.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Sand Paper Nos. 0496 5.00 8.00 40.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
5,708.00
5,765.08
6,575.07
7,561.33
Cost for 104 RM 7,636.95

Considering cost reduction of 11.15% in the rate for 60Kg
Rate per RM RM 137041 73.43 0.89 65.24
137050 Anti-corrosive painting to weld collar for Thermit welded rail joints on track or on cess
for new welded joints to protect against normal corrsion for any rail section with two
coats of ready mixed bitumenous black paint of reputed make confirming to IS:9862-
1981 on welded area upto 10cm on either side including on the underside of rail foot
by brush including surface preparation as per Railway's AT Weld Manual including
lettering / weld numbering with approved enamel paint as directed
Note: Before painting, dust, loose rust and mill scale and dirt shall be removed
thoroughly by wire brushing.Scrubbing welded area with water to make it free from
slag and other water soluble compounds to make it dry.

Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 20.00 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,661.00

Code (Rs.) (Rs.)
2,687.61
3,065.22
3,525.00
137060 Anti-corrosive painting to weld collar for Thermit welded rail joints on track for old
painted joints in normal corrosive prone area for any rail section with two coats of
ready mixed bitumenous black paint of reputed make confirming to IS:9862-1981 on
welded area upto 10cm on either side including on the underside of rail foot by brush
including surface preparation as per Railway's AT Weld Manual including lettering /
weld numbering with approved enamel paint as directed
Note:
1.Before painting, dust,dirt and flaked paint from the welded joint shall be removed
thoroughly by scrapping with wire brush. Grease and oil shall be removed by use of
appropriate solvent confirming to IS Specification 1745-1976.
2.Use of detergent followed by water washing should also be done to ensure
removal of oil and grease apart from the greasing compound.
3.The paint should be procured along with the thinner recommoned by the
manufacturer of the paint.
4.No other thinner like kerosine oil should be used.

Material:
Solvent confirming to IS Specification 1745-1976. Litre 0302 150.00 2.00 300.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 20.00 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,961.00
2,990.61
3,410.79
3,922.41
137070 Anti-corrosive painting to weld collar for Thermit welded rail joints on track or on cess
for new welded joints to protect against severe corrsion for any rail section with one
coat of high build epoxy paint (two pack) of reputed make confirming to RDSO
Specification M&C/PCN-111/99 on welded area upto 10cm on either side including
on the underside of rail foot by brush including surface preparation as per Railway's
AT Weld Manual including lettering / weld numbering with approved enamel paint as
directed
Note:
Befor painting,dust,loose rust and mill scale and dirt shall be removed thoroughly by
wire brushing.Scrubbing welded area with water to make it free from slag and other
water soluble compounds to make it dry.


Code (Rs.) (Rs.)
Material:
High build epoxy paint (two pack) as per RDSO's Specn. No. M&C/PCN/111/88 Litre 0303 440.00 8.00 3,520.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 20.00 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
5,541.00
5,596.41
6,382.71
7,340.11
137080 Anti-corrosive painting to weld collar for Thermit welded rail joints on track for old
painted joints in severe corrosive prone area for any rail section with one coat of high
build epoxy paint (two pack) of reputed make confirming to RDSO Specification
M&C/PCN-111/99 on welded area upto 10cm on either side including on the
underside of rail foot by brush including surface preparation as per Railway's AT
Weld Manual including lettering / weld numbering with approved enamel paint as
directed
Note:
1.Before painting, dust,dirt and flaked paint from the welded joint shall be removed
thoroughly by scrapping with wire brush. Grease and oil shall be removed by use of
appropriate solvent confirming to IS Specification 1745-1976.
2.Use of detergent followed by water washing should also be done to ensure removal
of oil and grease apart from the greasing compound.
3.The paint should be procured along with the thinner recommoned by the
manufacturer of the paint
4.No othe thinner like kerosine oil should be used

Material:
Solvent confirming to IS Specification 1745-1976. Litre 0302 150.00 2.00 300.00
High build epoxy paint (two pack) as per RDSO's Specn. No. M&C/PCN/111/88 Litre 0303 440.00 8.00 3,520.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Sand Paper Nos. 0496 5.00 20.00 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
5,841.00
5,899.41
6,728.28
7,737.52

Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
137090 Marking, inscribing, painting, writing, bordering etc. on new / old iron surface at
various locations of Points & Crossings with details of turn-in / turn-out reference
station mark on rail web for one set, duly preparing surface with contractor's wire
brush and applying two coats of yellow synthetic enamel paint of approved quality as
background and stenciling the details to suitable size, as described for every curve
reference station mark / switch / crossing details with black enamel paint of approved
quality complete, as directed :
Note: Stenciling of letters is only permitted. No hand written letters are accepted.
Details of cost for 2 sets. (Yellow & Black paint)
Material:
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,456.50
2,481.07
2,829.65
3,254.10
Cost for 2 sets. 3,286.64
Material:
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,450.00
2,474.50
2,822.17
3,245.49
Material:

Code (Rs.) (Rs.)
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,640.00
2,666.40
3,041.03
3,497.18

Material:
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,640.00
2,666.40
3,041.03
3,497.18
137100 Painting 2 coats to various P.Way Reference Post, Structures etc. with enamel paint
of approved make with 2 coats of different colours & letters, as directed by Engineer
in-charge.
137101 Kilometre & Gradient post

Details of cost for 15 posts (1.0 ltr white & 0.25 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
941.50

Code (Rs.) (Rs.)
950.92

Code (Rs.) (Rs.)
1,084.52
1,247.20
Cost for 15 posts 1,259.67
Rate per post Each 83.98
137102 Hectometre Post

Details of cost for 15 posts (1.5 ltr white & 0.50 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,084.00
1,094.84
1,248.67
1,435.96
137103 LWR / SEJ Board

Details of cost for 10 Boards (1.50 ltr white & 0.5 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,107.00
1,118.07
1,275.16
1,466.43
Cost for 10 Boards 1,481.10
Rate per board Each 148.11
137104 Level Crossing Boards including Road Sign Boards

Details of cost for 10 boards (1.0 ltr yellow, 1.00 ltr white & .50 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,262.00

Code (Rs.) (Rs.)
1,274.62
1,453.70
1,671.76
137105 Level Crossing Post

Details of cost for 8 Posts (1.0 ltr white & 0.5 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
995.50
1,005.46
1,146.72
1,318.73
Cost for 8 Posts 1,331.92
137106 Curve Post

Details of cost for 15 posts (1.0 ltr yellow & 0.50 ltr black paint reqd.)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
995.50
1,005.46
1,146.72
1,318.73
137107 Level Crossing Boom including fringe

Details of cost for 10 Metre Boom (1.0 ltr yellow & 1.0 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,032.00
1,042.32

Code (Rs.) (Rs.)
1,188.77
1,367.08
Cost for 10 Metre 1,380.75
137108 Level Crossing Boom without fringe

Details of cost for 10 Metre Boom (.50 ltr yellow & .50 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
842.00
850.42
969.90
1,115.39
137109 Curve Board

Details of cost for 10 Boards (1.50 ltr white & 0.5 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,107.00
1,118.07
1,275.16
1,466.43
137110 Curve details, SE, Versine, Station Nos. etc. per station.
Details of cost for 75 Stn.(2.0 ltr yellow & 1.0 ltr black paint reqd.)
Material:
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00

Code (Rs.) (Rs.)
2,660.00
2,686.60
3,064.07
3,523.68
Cost for 75 Stn. 3,558.91
Rate per station Each 47.45
137120 Painting 2 coats to Bridge Reference / Boards, Structures etc. along track with
enamel paint of approved make with different colours & letters, as directed by
Engineer in-charge.
137121 Bridge Board
Details of cost for 10 bridge boards (1.5 ltr White & 0.50 ltr black paint reqd.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,107.00
1,118.07
1,275.16
1,466.43
137122 Bridge Tablet

Details of cost for 30 bridge tablet (1.0 ltr white & .25 ltr black paint reqd.)
Material:
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
948.00
957.48
1,092.01
1,255.81
Cost for 30 bridge tablet 1,268.36
Rate per bridge tablet Each 42.28
137123 Bridge Height Gauge

Details of cost for 1 bridge (2.00 ltr white & 2.00 ltr black paint reqd.)
Material:
Labour:

Code (Rs.) (Rs.)
T&P Lumpsum 9901 1.00 10.00 10.00
1,880.50
1,899.31
2,166.16
2,491.08
Cost for 1 bridge 2,515.99
Rate per bridge Each 2,515.99
137124 HFL, FSL & DL on Bridge Pier / Abutment

Details of cost for 3 bridge (0.50 ltr white , 0.10 red & 0.50 black paint reqd.)
Material:
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
1,409.00
1,423.09
1,623.03
1,866.49
Cost for 3 bridge 1,885.15
Rate per bridge Each 628.38
137125 Miscellaneous General Boards, Jurisdiction Boards, Structures etc.
Details of cost for 9 Sqm i.e. Considering 6 Boards of size 1.5m x 1.0m each (
required 1.50 ltr white / yellow & 0.50 ltr black paint )
Material:
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
776.50
784.27
894.45
1,028.62
Cost for 9 Sqm 1,038.91

Code (Rs.) (Rs.)
137130 Attending the CC apron repairs under the sleeper where there is seperation of PSC
Sleeper along whole periphery and puncturing of apron under the sleepers, chiselling
as required including removal of foreign materials from the sleeper trench and
dewatering duly filling cement concrete with CONBEXTRA-GP2 or similar, the narrow
gaps completely including pouring, finishing, curing to match with the existing
C.C.apron surface and slopes complete, labour charges in traffic block and as per the
direction of Engineer Incharge.
Details of cost for 4 Sleepers

Material:
Fosroc conbextra-GP2 grout or similar make in 25 Kg bag Each 0474 494.00 8.00 3,952.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
5,138.50
5,189.89
5,919.06
6,806.92
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 14: Testing of Rails and Other Components
CHAPTER - 14 : Testing of Rails & Other Components

Code (Rs.) (Rs.)
141000 1. USFD Testing of Rails :
141010 Ultrasonic testing of single rails, required for fabrication of points and crossings by
using double crystal normal probe 4.0 MHz frequency with water / oil couplant. The
rails shall be tested by probing from the rail head top, rail head side and web with
typical oscillogram pattern for various probe positions as per 'Indian Railways
Standard Specification for Ultrasonic Testing of Rails and Welds', as applicable to
rails for fabrication of points & crossings. The rates are inclusive of contractor’s men,
materials & machines complete and as directed.
Detail of cost for 12 Nos. of 13 metres i.e. 156m

Material:
Sand Paper Nos. 0496 5.00 16.00 80.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
Misc.:
T & P (Training charges at LKO) Lumpsum 9901 1.00 100.00 100.00
7,657.50
7,734.08
8,820.71
10,143.82
Cost for 156 metres 10,245.26
141020 Carrying out Through USFD testing of running rails & welds (excluding flange testing)
including level crossings, lead portion of points and crossings, hand probing of
machined portion of tongue rail, hand probing of machined portion of SEJ and
scabbed rail testing of all types of rails by NBC (Need Based Concept) method under
traffic conditions as per provisions of IR’s "USFD Manual & Specifications for
Ultrasonic Testing of Rails and Welds" with latest correction slips & related
instructions, duly marking defects, submission of daily reports and storing back-up
data, as specified & directed.
Note:
0
The SRT/DRT machine should have minimum of 9 probes (including 37 forward
/backward probe for detecting bolt hole cracks.
141021 With Contractor’s USFD machine

Detail of cost for 3 TKM
Material:
Cotton Jute Kg 0494 40.00 0.20 8.00
Labour:
Allowances for carraiage of equipment and Travel/Stay for the team @ 50% labour 3,082.50
Misc.:
T & P (Training charges at LKO and Transportation of machinery) Lumpsum 9901 1.00 400.00 400.00

Code (Rs.) (Rs.)
Hire charges of USFD testing machine(B-Scan) Day 0128 2500.00 1.00 2,500.00
12,189.00
12,310.89
14,040.57
16,146.66
Cost for 3 TKM 16,308.12
141022 With Railway's USFD machine including related T&P and probes
Detail of cost for 3 TKM
Material:
Cotton Jute Kg 0494 40.00 0.20 8.00
Labour:
Allowances for carraiage of equipment and Travel/Stay for the team @ 50% labour 3,082.50
cost
Misc.:
9,689.00
9,785.89
11,160.81
12,834.93
Cost for 3 TKM 12,963.28
142000 2. USFD Testing of A.T.Welds :

142010 Carrying out USFD testing of Alumino Thermic (AT) welds on all types of rails, using
0º (2 MHz) double crystal; 70º (2 MHz) 20mm x 20mm single crystal probe for head &
flange testing; 2 nos. 45º (2 MHz) single crystal with tandom rig for testing from rail
top to bottom & for half moon testing and 70º (2 MHz) 20mm x 20mm side looking
probe by NBC (Need Based Concept) method under traffic conditions as per
provisions of IR’s "Manual & Specifications for Ultrasonic Testing of Rails and Welds"
& related instructions duly marking the defects, submission of daily reports and
storing back-up data as specified & directed. The rates are inclusive of contractor’s
men, materials & machines complete unless otherwise specified and directed.
142011 Track having upto 3 rail panels - With Contractor’s USFD machine :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00

Code (Rs.) (Rs.)
Labour:
Misc.:
6,872.00
6,940.72
7,915.89
9,103.27
142012 Track having more than 3 Rail panels - With Contractor’s USFD machine.
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
6,872.00
6,940.72
7,915.89
9,103.27
142013 Track having upto 3 rail panels - With Railways’ USFD machine including related
T&P and probes :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
6,072.00

Code (Rs.) (Rs.)
6,132.72
6,994.37
8,043.52
142014 Track having more than 3 rail panels - With Railways’ USFD machine including
related T&P and probes :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
5,972.00
6,031.72
6,879.18
7,911.05
143000 3. USFD Testing of Flash Butt Weld :

143010 Carrying out USFD testing of Flash Butt (FB) & Gas Pressure (GP) welds on all types
of rails using 2 single crystal 45º (2 MHz) for head testing and one single crystal 70º
(2 MHz) probe for web & flange testing by NBC (Need Based Concept) method under
traffic conditions as per provisions of IR’s "Manual & Specifications for Ultrasonic
Testing of Rails and Welds" & related instructions, duly marking the defects,
submission of daily reports and storing back-up data as specified & directed. The
rates are inclusive of contractor’s men, materials & machines complete unless
otherwise specified and directed.
143011 Track having upto 3 rail panels - With Contractor’s USFD machine :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:

Code (Rs.) (Rs.)
Misc.:
Training charges at LKO and Transportation of machinery Lumpsum 9901 1.00 200.00 200.00
7,303.00
7,376.03
8,412.36
9,674.22
143012 Track having more than 3 rail panels - With Contractor’s USFD machine :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
7,303.00
7,376.03
8,412.36
9,674.22
143013 Track having upto 3 rail panels -With Railway's USFD machine including related T&P
and probes :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
6,503.00
6,568.03

Code (Rs.) (Rs.)
7,490.84
8,614.46
143014 Track having more than 3 rail panels - With Railway's USFD machine including
related T&P and probes :
Material:
Sand Paper Nos. 0496 5.00 8.00 40.00
Cotton Jute Kg 0494 40.00 1.00 40.00
Labour:
Misc.:
6,503.00
6,568.03
7,490.84
8,614.46
Cost for 1 weld Each 145.01
144000 4. USFD Testing of SEJ :

144010 USFD testing of Switch Expansion Joint (SEJ) by NBC (Need Based Concept)
method under traffic conditions as per provisions of "IR’s Manual & Specifications for
Ultrasonic Testing of Rails and Welds" with latest amendments & related instructions,
duly marking the defects, submission of daily reports and storing back-up data, as
specified in the special conditions, as applicable to rail testing. The rates are inclusive
of contractor’s men, materials & machines complete unless otherwise specified and
directed.
Note: One set consists of both SEJ on left and right rail.
144011 With Contractor’s USFD machine

Details of cost for 8 set SEJ'S
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
Misc.:
7,517.50

Code (Rs.) (Rs.)
7,592.68
8,659.45
9,958.36
Cost for 8 set SEJ'S 10,057.95
144012 With Railway's USFD machine including related T&P and probes
Details of cost for 8 set SEJ'S
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
Misc.:
6,717.50
6,784.68
7,737.92
8,898.61
Cost for 8 set SEJ'S 8,987.60
144020 Providing an assiting gang comprising of 4 men per day with SSE/P.Way/ USFD for
carrying out ancillary works viz., lookout, watering, paint marking and handling
machine for USFD test with Single Rail Testor (SRT) machine and as directed by
Engineer incharge.
Note:
1. This item shall be operated only when there is no departmental staff available and
only with the prior approval of concerned Sr. DEN/Co-ordination.
2. In case, contractor provides less no. of Labour, payment will be deducted for each
such person @ 50% of the accepted item rate.
Details of Cost per one day per SRT

Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,734.00
1,751.34
1,997.40
2,297.01
Cost for one machine per day 2,319.98
Rate per Gang per Day Gang Day 2,319.98

Code (Rs.) (Rs.)
144030 Providing an assiting gang comprising of 6 men per day with SSE/P.Way/ USFD for
carrying out ancillary works viz., lookout, watering, paint marking and handling
machine for USFD test with Double Rail Testor (DRT) machine and as directed by
Engineer incharge.
Note:
1. This item shall be operated only when there is no departmental staff available and
only with the prior approval of concerned Sr. DEN/Co-ordination.
2. In case, contractor provides less no. of Labour, payment will be deducted for each
such person @ 1/3 rd of the accepted item rate.
Details of Cost per one day per DRT

Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,596.00
2,621.96
2,990.35
3,438.90
Cost for one DRT per day 3,473.29
Rate per Gang per day Gang Day 3,473.29
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 15: Heavy Track Machines
CHAPTER - 15 : Heavy Track Machines

Code (Rs.) (Rs.)
151000 1. PQRS Related Works :
151010 Unloading of mono-block PSC sleepers in PQRS Depot using crane from Railway
wagons and stacking them at the end of Assembling Line with all leads & lift.
Note:
1.Unloading to be done within the stipulated time as and when loaded BFRs are
received, so as to hand over empty BFRs without demurrage;
2.If unloading is not done within the stipulated time, the demurrage raised by the
Railways shall be borne by the Contractor.
3.Contractor has to arrange necessary tools etc., complete for unloading from BFR’s
and stacking.
151011 With Railway’s portal crane

Details of cost for unloading 1660 sleepers with 2 portal cranes
Labour:
Misc.:
T & P (Beater, Rail tounge, Hammer, Crow bars, Tami bar etc.) Lumpsum 9901 1.00 20.00 20.00
6,559.00
6,624.59
7,555.34
8,688.65
151012 With Contractor’s portal crane / mechanical means

Details of cost for unloading 1660 sleepers with 2 portal cranes
Labour:
Misc.:
Hire charges of Portal Crane (with Fuel & Driver) Hour 0159 250.00 16.00 4,000.00
10,559.00
10,664.59
12,162.96
13,987.41
151020 Assembling of 13m / 12.6m long track panels in PQRS Depot by spreading PSC
sleepers already unloaded and stacked, to correct spacing as per specified sleeper
density per km, using portal crane, placing service rails on them and fixing rails to
sleepers with standard fastening properly to get correct gauge with all contractor’s
labour, tools, plants etc.

Code (Rs.) (Rs.)
Details of cost for 520 TRM by 2 portal cranes .
On each portal crane, one helper ( semi skilled ) for operation of crane, 2 persons for
assistance during work, 6 persons for spreading PSC sleepers, placing rails and
fixing fastenings work.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Beater, Rail tongue, Hammer, Crow bars, Tommy bar etc.) Lumpsum 9901 1.00 36.00 36.00
12,861.00
12,989.61
14,814.65
17,036.85
Cost for 520 TRM 17,207.22
151022 With contractor’s portal crane

Details of cost for 520 TRM by 2 portal cranes [ On each portal crane one helper (
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
16,861.00
17,029.61
19,422.27
22,335.61
Cost for 520 TRM 22,558.97
151030 Loading pre-assembled panels of PSC sleepers in layers on BFR with portal crane in
PQRS Depot, complete in such a manner that it may be dispatched in train formation
to mid section, as directed by engineer in-charge.

Labour:
Misc.:
T & P (Rail tounge, Hammer, Crow bars, Tami bar etc.) Lumpsum 9901 1.00 10.00 10.00
1,882.00
1,900.82
2,167.89

Code (Rs.) (Rs.)
2,493.07
151032 With contractor’s portal crane

Labour:
Misc.:
5,882.00
5,940.82
6,775.51
7,791.83
151040 PQRS:Pre Block activity:Removing of the existing ballast from crib portion of the full
length of existing PSC sleeper and further up to the bottom of sleepers to
accomadate new sleeper and dumping the ballast so removed on the
shoulders/cess with contractor own labour, tools and plants etc, complete with all
lead and lift and as directed by the Engineer-in-charge at site including crossing of
track wherever necessary.

Labour:
T & P (Rake ballast, Pans,Crow bars, Beater etc.) Lumpsum 9901 1.00 100.00 100.00
5,272.00
5,324.72
6,072.84
6,983.77
151050 PQRS:During line block activity: Dismantling existing track, levelling disturbed and
uneven surface of bed up to bottom of sleeper, Loading the released panels in to
BFR with Railway's portal cranes, Placing new panels from BFRs on to track with
Railway's portal crane, Linking of Track with all fittings, placing ballst as required in
crib and shoulders, aligning and surfacing of track, attending track parametres and
initial packing to track to allow traffic at restricted speed of 20 kmph with contractors
own labour, tools etc, complete and lead & lift as directed by the Engineer-in-charge
at site including crossing of track wherever necessary.
Note: The PQRS cranes with fuel and operators will be provided by Railway.

Labour:

Code (Rs.) (Rs.)
6,074.00
6,681.40
6,748.21
7,696.34
8,850.79
151060 PQRS:Post Block activity, Pulling back the left over ballast from shoulders/cess in to
track and dumping in cribs and shoulders, regulating and boxing with available
ballast to facilitate surfacing of track during lifting.with contractors own labour, tools
etc, complete and lead & lift as directed by the Engineer-in-charge at site including
crossing of track wherever necessary.

Labour:
3,548.00
3,583.48
4,086.96
4,700.00
151070 Unloading of released track panels consisting of all types of rails & sleepers from
Railway wagon at PQRS Depot, using portal cranes including dismantling of released
panels to rails, sleepers & fastenings and stacking them material-wise and
classification-wise at nominated locations within the yard limits with all leads, lift and
crossing of tracks.
151071 With Railway’s portal crane for PSC sleeper track

Details of cost for 390 TRM by 2 portal cranes [ On each portal crane one helper
(semi skilled ) for operation of crane, 1 person for assistance during work ]
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
For dismantling panels & stacking in a countable manner
Misc.:
13,994.00
14,133.94
16,119.76
18,537.72

Code (Rs.) (Rs.)
Details of cost for 390 TRM 18,723.10
151072 With Railway’s portal crane for other than PSC sleeper track
Details of cost for 520 TRM by 2 portal cranes [ On each portal crane one helper
(semi skilled ) for operation of crane, 1 person for assistance during work ]
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
11,149.00
11,260.49
12,842.59
14,768.98
151073 With contractor’s portal crane for PSC sleeper track

Details of cost for 390 TRM by 2 portal cranes
On each portal crane, one helper ( semi skilled ) for operation of crane, 1 person for
assistance during work.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
19,459.00
19,653.59
22,414.92
25,777.16
151074 With contractor’s portal crane for other than PSC sleeper track
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:

Code (Rs.) (Rs.)
15,149.00

Code (Rs.) (Rs.)
15,300.49
17,450.21
20,067.74
151080 Mechanical / Manual loading of all types of rails on BFRs in PQRS Depot, as directed
151081 Mechanised loading with Railway's cranes

Details of cost for 520 RM by 2 portal cranes [ On each portal crane one helper (
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
3,355.00
3,388.55
3,864.64
4,444.34
Cost for 520 RM 4,488.78
Rate per RM RM 8.63
151082 Mechanised loading with contractor's cranes

Details of cost for 520 RM by 2 portal cranes [ On each portal crane 1 crane
Labour:
Misc.:
5,736.00
5,793.36
6,607.33
7,598.43
Cost for 520 RM 7,674.41
151083 Manual loading by contractor's labours

Details of cost for 520 RM (40 Rails of 13 metre length)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,700.00

Code (Rs.) (Rs.)
9,797.00
11,173.48
12,849.50
Cost for 520 RM 12,978.00
151090 Doing various miscellaneous works for Railway's PQRS cranes (one set of 2 portals)
for proper upkeep of crew rest van / rest room, as directed by the machine in-charge
by :
(1) Fuelling the machine, duly bringing diesel / hydraulic oil from the stacked drums;
(2) Bringing water to the staff rest van or staff rest room, cleaning rest van / rest
room, cooking food for Track Machine staff or bringing food from outside (cost of
food shall be borne by the staff concerned).
Details of cost for 1 day for one Machine / Crew rest van
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
872.00
880.72
1,004.46
1,155.13
Cost for per day for one machine / crew rest van 1,166.68
Cost for Per day per machine / crew rest van Day 1,166.68
151100 Guarding and watching the Track machine / group of machines, spare parts, oils,
grease etc. of PQRS cranes (one set of 2 portals) during day and night time in a shift
of 12 hours each, at all locations wherever necessary, as instructed by the machine
in-charge.
Note: One shift comparises of 12 hours.
Details of cost for 1 day for Guarding & watching Track machine / Group of machines
considering 2 chowkidars for 1 day i.e. (12 hr's Shift)
Labour:
Chowkidar (Semi skilled) Day 0039 505.00 2.00 1,010.00
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,020.00
1,030.20
1,174.94
1,351.18
Cost for per day for one track machine / group of machines 1,364.70
Rate per shift Shift 682.35

Code (Rs.) (Rs.)
151110 Laying of auxiliary track with all types of rails, already available on cess, fixing rails
on wooden blocks / CST-9 pots at 2m interval, true to square, to required alignment
& level, fixing with spikes / screws / keys, linking rails with fish plates, bolts & nuts to
a gauge of 3400mm (with reference to centre line of existing BG track), levelling both
the rails to same plane as that of BG track over stone ballast by way of removing
ballast from shoulders of existing track, providing one proper packing. Subsequently,
dismantling auxiliary track after completion of PQRS work at site by way of removing
wooden blocks / CST-9 pots and carrying same to next stretch / location, if required,
where auxiliary track has to be laid and spreading the same at required locations and
leaving rails there itself for carrying out TRR work later.
Details of cost for 200 Track Metre

Labour:
(i) Ballast bed plaining for CST-9/Wooden Block
(ii) Positioning & Fixing Rails on CST-9/Wooden Block
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Rail dolly, Diplorry, Spanner, Hammer, Crow bars, Tami bar, Beater, Auger Lumpsum 9901 1.00 42.00 42.00
9,776.00
9,873.76
11,261.02
12,950.18
151120 In PQRS work, through rail renewal of BG track on PSC sleepers of any density with
all types of rails / rail panels lying in auxiliary track or on cess for replacement of
service rails including handling of rails by way of dragging, pairing etc. and leading
released service rails to load into BFR / Lorry or to shift to next location including
crossing of track with lead & lift and any other incidental works as required.
151121 For rails upto 13m length

Labour:
For removal of existing rail and Re fixing the rails taken from auxiliary track
Mate (Skilled) Day 0002 609.00 1.00 609.00
For carting of service rails etc.
Misc.:
T & P (Rail tounge, Spanner, Hammer, Crow bars, Beater etc.) Lumpsum 9901 1.00 80.00 80.00
18,864.00
19,052.64
21,729.54
24,988.97

Code (Rs.) (Rs.)
Cost for 260 TRM 25,238.86
151122 For rails of more than 13m and upto 40m length
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
26,658.00
26,924.58
30,707.48
35,313.61
Cost for 390 TRM 35,666.74
151123 For rails above 40m length

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
35,492.00
35,846.92
40,883.41
47,015.92
Cost for 520 TRM 47,486.08
151130 Through Rail renewal with free service rails of all types by removing existing running
rails, already cut into free rails / rail panels for making auxiliary track, including
attending alignment, cross level, gauging, packing; wherever required including
crossing of track, as directed.

Labour:
For removal of existing rail and Re fixing free service rails
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
18,864.00
19,052.64
21,729.54
24,988.97
Cost for 260 TRM 25,238.86
152000 2. Track Relaying Train (TRT) Related Works :

152010 Carrying out preparatory works before operation of Track Relaying Train (TRT), such
as –
(1) Broken corroded sleepers to be removed and fastenings to be loosened;
(2) Excess ballast to be removed and crib ballast between consecutive sleepers
removed upto bottom of sleepers;
(3) Check rails of level crossings falling in the range of work to be removed;
(4) In case of CTR, rail panels placed at 1.5m away from existing track centre;
(5) All existing longer wooden sleepers if available or interlaced sleepers of different
height to be removed;
(6) Cutting of existing rails to 6m piece closure at work site from where Track
Relaying Train (TRT) will start working on that day;
(7) Removal of Reverse jaw type CST-9 sleeper if available joggled fish plates, OHE
bonds & other obstructions etc.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Hammer, Chisel, Spanner, Crow bars, Tommy bar, Beater etc.) Lumpsum 9901 1.00 44.00 44.00
11,249.00
11,361.49
12,957.78
14,901.45
Cost for 1000 TRM 15,050.46

Code (Rs.) (Rs.)
152020 Loading of PSC sleepers in layers on BRH (special type modified BFR for TRT /
PQRS working) by using contractor’s Gantry (Crane) in TRT / PQRS Base Depot,
placing dunnage (wooden beddings / wedges) between sleepers to cover entire layer
of sleepers, complete in such a manner that it may be dispatched in train formation.
152021 Mechanised loading with Railway's cranes

Details of cost for 1660 sleepers by 2 portal cranes
On each portal crane 1 crane operator, 1 Assistant crane operator (semi skilled) & 1
helper for operation of crane during work.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
For providing dunnage (wooden beddings) between layers
Misc.:
4,804.00
4,852.04
5,533.75
6,363.81
152022 Mechanised loading with Contractor's cranes

Details of cost for 1660 sleepers by 2 portal cranes
On each portal crane 1 crane operator, 1 Assistant crane operator (semi skilled) & 1
helper for operation of crane during work.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
For providing dunnage (wooden beddings) between layers
Misc.:
8,804.00
8,892.04
10,141.37
11,662.58
152030 Unloading of released sleepers from BRH (special type modified BFR for TRT
working) in Depot by using contractor’s Gantry (Crane) and stacking them at
nominated locations within the yard limits with all leads & lift.
Details of cost for 1660 sleepers by 2 portal cranes [ On each portal crane 1 crane
operator, 1 Assistant crane operator (semi skilled) & 1 helper for operation of crane
during work ]

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
For stacking sleepers in a countable manner
Misc.:
10,536.00
10,641.36
12,136.47
13,956.94
153000 3. T-28 Machine Related Works :

153010 Dismantling of existing Turnout by removing switches, rails, crossings, check rails,
sleepers and all fixtures and stacking all released materials, removing ballast and
muck by excavating upto required depth, preparation of formation bed, laying of pre
assembled Turnout by Railway's T-28 machine, linking of track with all fittings, filling
up of ballast duly screened, packing, adjusting, opening & housing of switch, testing
operation of switch assembly and attending track parameters, so as to make track fit
for 20 kmph speed including disposing off muck to indicated places upto free lead
after the block working etc. complete.
Note: Rate includes making necessary preparation for T-28 machine movement like
preparation of approaches, transportation and laying of wooden sleepers/blocks, etc.
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Dismantling of Turnout & stacking of released material
(ii) Removing ballast & muck (Including levelling)
(iii) Preparation of formation bed for runing T-28
(iv) After laying of turn out filling the ballast, packing & Fitting of all components of
Misc.:
T & P (Rail tounge, Crow bars, Hammer, Beater,spanner, pan iron morter etc.) Lumpsum 9901 1.00 140.00 140.00
30,308.00
33,338.80
33,672.19
38,403.13
44,163.60

Code (Rs.) (Rs.)
Rate per set Each 44,605.24

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(iv) After laying of turn out filling the ballast, packing &Fitting of all components of
Misc.:
34,892.00
38,381.20
38,765.01
44,211.50
50,843.22
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
39,476.00
43,423.60
43,857.84
50,019.86
57,522.84

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
42,944.00
47,238.40
47,710.78
54,414.15
62,576.27
153020 Dismantling of existing switch by removing switches,rails,sleepers,fixtures and

stacking all released materials, removing ballast and muck by excavating upto
required depth, preparation of formation bed, laying of pre-assembled switch by
Railway’s T-28 machine, linking of track with all fittings, filling ballast duly screened,
aligning, packing, adjusting, opening & housing of switch, testing operation of switch
assembly and attending track parameters so as to make track fit for 20 kmph speed
including disposing off muck to indicated places after the block working etc.
complete.
Note: Rate includes making necessary preparation for T-28 machine
working/movement such as providing and removing rail closures, preparation of
approaches, transportation and laying of wooden sleepers/blocks, etc.
153021 1 in 8½ Switch
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Dismantling of Switch & stacking of released material
(iv) After laying of turn out filling the ballast & packing
(v) Fitting of all components of Switch

Code (Rs.) (Rs.)
Misc.:
12,981.00
14,279.10
14,421.89
16,448.17
18,915.39
153022 1 in 12 Switch
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,713.00
16,184.30
16,346.14
18,642.78
21,439.19
153023 1 in 16 Switch
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
16,697.00
18,366.70
18,550.37
21,156.69
24,330.20
153024 1 in 20 Switch
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
18,859.00
20,744.90
20,952.35
23,896.15
27,480.58

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
(iv) After laying of turn out filling the ballast ,packing & fitting all components
Misc.:
14,721.00
16,193.10
16,355.03
18,652.91
21,450.85
154000 4. BCM / FRM Machine Related Works :

154010 Carrying out preparatory works for operation of Ballast Cleaning Machine (BCM)
which includes making trench in track for inserting cutter bar, supporting track on
wooden block supplied by Railway, removal of ballast alongwith muck from shoulder
which is out of reach of cutter chain and putting the same in cutting width or between
rails. Rate includes all miscellaneous works, e.g. opening and re-fixing of joggled fish
plates, OHE Bonds, dismantling & removing obstructions etc.

Labour:
Misc.:
T & P (Hammer, Chisel, Spanner, Crow bars, Tommy bar, Beater etc.) Lumpsum 9901 1.00 20.00 20.00
5,086.00
5,136.86
5,858.59
6,737.38
154020 Carrying out various works during operation of BCM, like filling up of ballast from
available locations (including adjoining tracks), required packing, adjustment of PSC
Sleepers, provision wooden blocks supplied by department and attending track
parameters etc. complete so as to make track fit for 20 kmph speed.
Details of cost for 360 TRM ( 1 group of two persons deputed for 40 metre track )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T & P (Rake ballast, Crow bars, Hammer, Beater etc.) Lumpsum 9901 1.00 52.00 52.00
8,850.00
8,938.50
10,194.36
11,723.51
Cost for 360 TRM 11,840.75
154030 Removal of screened muck discharged by BCM, where muck disposal on side slope
is restricted due to platform, cutting, OHE mast etc. and disposing it beyond 5m from
edge of cutting upto 3m deep or alternatively carting it upto 50m for disposing off
beyond the end of cutting / platform and making up cess wherever low.
Details of cost for 520 TRM (1 group of two persons deputed for 52 Track metre )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,700.00
9,797.00
11,173.48
12,849.50
Cost for 520 TRM 12,978.00
154040 Removal of screened muck discharged by FRM/SBCM where muck disposal on side
slope is restricted due to platform, cutting, OHE mast etc. and disposing it beyond
5m from edge of cutting upto 3m deep or alternatively carting it upto 50m for
disposing off beyond the end of cutting / platform and making up cess wherever low.
Details of cost for 780 TRM (1 group of two persons deputed for 78 Track metre)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,700.00
9,797.00
11,173.48
12,849.50
Cost for 780 RM 12,978.00

Code (Rs.) (Rs.)
154050 Extra to item nos. from 154030 and 154040 for disposal of muck at a distance
beyond 50m for every additional lead of 50 metres or part thereof upto 500 metres.
average lead of 250 metre for dispoal of muck)(@ one man per 25 TRM)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00
4,373.30
4,987.75
5,735.91
Cost for 500 TRM / 250 metres lead 5,793.27
Cost for 500 TRM / every 50 metres lead 1,158.65
Rate per TRM / every 50 metres TRM 2.32
154060 Extra to item nos. from 154030 and 54040 for disposal of muck for additional lift of 1
metre or part thereof beyond 3 metre lift in case of disposal of muck from track in
cutting.
Details of cost for 400 TRM (Extra labour element required for additional average lift
of 3 metre for dispoal of muck)(@ one man per 20 TRM)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,330.00
4,373.30
4,987.75
5,735.91
Cost for 400 TRM / 3 metre lift 5,793.27
Cost for 400 TRM / every 1 metre lift 1,931.09
Rate per TRM / every 1 metre lift TRM 4.83
154070 Removing the ballast from shoulders, left over after BCM/SBCM working, screening
the same removing the muck and putting back the screened ballast in track profile,
boxing the ballast to profile and using released muck for cess making or throwing
away within 50m lead and 3m lift when not required for cess repairs and as directed
by the Engineer-in-charge.
Note: This item shall be used only when BRM is not available.

(1 person deputed for 20 Track running metre length )
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
5,085.50

Code (Rs.) (Rs.)
5,136.36
5,858.01
6,736.71
154080 Ballast equalisation & ballast profiling after completion of deep screening work by
BCM and/or after unloading of ballast by DMT (Ballast Train), as directed by Site
Engineer as per IRPWM including heaping of ballast in tamping zone keeping rails &
sleeper top free from ballast, spacing and squaring of sleeper, gauging, cleaning of
muck, proper fixing of fastening, attention during each round of sleeper tamping in
relation to pre & post working
Note:
Payment shall be made only once in irrespective of numbers of TTRM packing round
and after restoration of normal speed and restoration of complete ballast profile and
cess profile.
Details of cost for 200 TRM (1group of two persons deputed for 40 Track metre
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Rake ballast, Crow bars, Beater etc.) Lumpsum 9901 1.00 20.00 20.00
4,634.50
4,680.85
5,338.50
6,139.28
154090 Making cess in deep screened track by using screened muck discharged by BCM
where cess is low or cutting cess to required depth upto 4m from centre of track,
where cess is high and disposing off extra muck beyond 5m from edge of cutting
which are upto 3m deep or alternatively carting it upto 50m for disposing it off beyond
cutting or platforms, so as to make cess as per standard profile including providing
proper slope.
Details of cost for 260 TRM (1group of two persons deputed for 26 Track metre for
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
9,700.00
9,797.00
11,173.48
12,849.50
Cost for 260 TRM 12,978.00

Code (Rs.) (Rs.)
154100 Carrying out Through packing of sleepers to make track fit for 30 KM speed as per
procedure stipulated in latest version of IRPWM, behind BCM including filling ballast
when only lifting is carried out by BCM.
Details of cost for 182 TRM ( 1 Person will do packing including filling the ballast 14
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,700.00
9,797.00
11,173.48
12,849.50
Cost for 182 TRM 12,978.00
154110 Pulling the left over ballast to the shoulders and dumping excess ballast in the cribs
and shoulders including boxing/profiling as per IRPWM of track together with left over
stretches at fixed structures/masts immediately after FRM work, leveling the muck for
making up cess and side slopes including removing and re-fixing of traction bonds
during line block with all contractors labour, tools, plant, all lead, lift, crossing of track
etc. complete and as directed by the Engineer-in-charge.
Rate analysis for 500 Track Metres

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Hammer,spanner, mortar pan etc.) Lumpsum 9901 1.00 30.00 30.00
9,690.00
9,786.90
11,161.96
12,836.25
Cost of 500 Track Metre 12,964.62

Code (Rs.) (Rs.)
154120 Pre, during, and post BCM works for deep screening of ballast in Points and
crossings with all contractor's labour, tools and plants as required to carry out the
work to the standards in specific time including crossing of tracks etc. complete and
as directed by the Engineer - in - charge.
I. Pre-BCM Operation : a) making trenches for insertion of cutter bars at various
locations as per the directions of engineer in charge. Ie., one trench ahead of one rail
length from SRJ and second trench near sleeper No 62 ( 1in 12) etc., b) Filling up
ballast up to sleeper level. c) Tightening of fittings/ plate screws, RECs, Stud bolts,
check rail bolts.
II. During BCM Operation : a) Assistance to S&T Department : Opening of cables at
approach of Points & Crossings, TLD Boxes/ removing of Point motor and refixing
the same and covering cables after passing of BCM in block period with S&T Staff. b)
Engineering : c) Removing of two long sleepers ie., sleeper No 3 & 4 and refixing the
same in position during block after passage of BCM. d) Removing obstruction ie.,
S&T CC block duly digging with crow bars and breaking with chisel/ hammer, cutting
of rail pegs with gas. e) To remove, excess ballast on rail table for free movement of
BCM and for packing purpose. f) Extension of cutter bar wherever required in
assisting machine staff. g) Removing of cutter bar/ Chain links from the trenches
after screening work by BCM.
III . Post BCM Operation : a) Packing switch portion including Motor long sleeper ie.,
SRJ to heel joint to to reset Point for train movement & initial packing of lead portion
to allow train at 20KMPH and lifting the track in two stages (50mm to 75mm in each
lift) wherever required for correcting the longitudinal surfacing b) Dumping of ballast
in the naked crib portion on main line turnout side for initial packing purpose. c)
Boxing / Levelling of muck duly ensuring levelling of muck on cess side and lowering
of cess to the deep screened depth and removing of muck in between the lines and
leading up to 250mts.
Note:
1. For technical reasons, some of the points and crossings cannot be deep screened
either fully or partially by BCM, in which case, the left over length will be deep
screeniend manually.
2. The length of points and crossings assembly for payment of this item should be
taken from SRJ to longest concrete sleeper available just beyond heel of crossing
along main line..
Details of cost for one Points and crossing 1 in 12 points and Crossings for a length
of 45.50m
Man Power
Mate (Skilled) Day 0002 609.00 0.50 304.50
For Pre Block,Post block & during block activities
Misc
T&P (no rates reqd.) Lumpsum 9901 1.00 60.00 60.00
5,484.00
5,538.84
6,317.05
7,264.60
Cost for one Points and crossing 1 in 12 points and Crossings for a length of 45.50m 7,337.25

Code (Rs.) (Rs.)
155000 5. CSM, Duomatic and 3X Sleeper Tamping Machines :
155010 Carrying out pre-tamping, during tamping and post-tamping work for tamping track
with all types of rails, sleepers & sleeper density by various Track Tamping
machines, like CSM,DUO/3X Machines which include :
(1) Re-adjustment of ballast, heaping-up of ballast, filling-up of cavities in tamping
zone by picking ballast from stacks / shoulders / crib of adjoining track upto lead of
50 m to ensure effective packing;
(2) Clearing of ballast on sleepers to make them visible to operator,
(3) Clearing of ballast over rail foot to facilitate holding of rail by rollers of TTRM;
(4) Digging, screening and replenishment of ballast at mud pumping / rounded ballast
in sleeper crib location;
(5) Tightening of loose fittings immediately before & after tamping;
(6) Replacement of broken / missing fittings supplied by Railway;
(7) Correcting displaced sleepers to position alongwith squaring;
(8) Re-setting of worked-out / fallen fittings;
(9) Removing and re-fixing joggled fish plates & wooden blocks, wherever necessary;
(10) Manual consolidation of ballast in crib / shoulders;
(11) Removing and refixing of traction bonds during the block in electrified sections
(12) Dressing of ballast
Note:
1. Contractor to provide minimum 40 men with 1 supervisor and 2 mates for
carrying out above work.
2. Tamping blocks are not identical & it may be given at any time either during day or
night.
3. Stages of payment a) 30% of the rate will be paid on completion of pre tamping
attention, b) Balance 70% of the rate will be paid on completion of post tamping.
4. Recovery at the rate of twice the above applicable rate will be effected in case
contractor fails to carry out pre/during/post operation.
5.Payment shall be made only once in irrespective of numbers of TTRM packing
round and after restoration of normal speed and restoration of complete ballast
profile.
155011 For day time block working

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Pre-tamping work( as like recouped missing fittings, changing PSC, recouping
(ii) Post-tamping work (filling crib ballast, recoupment of all missing fittings &
Misc.:
T & P (Rail tounge, Crow bars, Hammer, Beater,spanner, pan iron morter, cane Lumpsum 9901 1.00 86.00 86.00
10,860.00
11,946.00
12,065.46
13,760.66
15,824.76
Cost for 1000 TRM 15,983.00
155012 For night time block working


Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
12,169.00
13,385.90
13,519.76
15,419.29
17,732.18
Cost for 1000 TRM 17,909.50
155013 Under Conditions not requiring Traffic Block

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
6,550.00
6,615.50
7,544.98
8,676.72
Cost for 1000 TRM 8,763.49
155020 Pre, during & post tamping operations, for tamping of track on level crossing portion
on all types of track structre and density, during traffic block, duly opening the road
surface by digging up to the required width and up to 50mm below bottom of sleeper
to facilitate tamping, removing and refilling ballast, adustment of deficient ballast if
necessary by picking from adjoining track/shoulder/cribs, removing and refixing all
inter locking gears interfering, removing and re-fixing of check rails and painting of
running rail & check rail with coaltar emulsion, completing road surface to smooth
motorable condition after tamping is over, including tightening of loose fittings,
replacement of broken/missing fittings, correction of displaced sleepers to correct
position and as directed by Engineer incharge.

Code (Rs.) (Rs.)
155021 Level crossing with ashplated surface
Details of cost for 40 Sqm (Lumpsum area for 9 metre wide LC for one Line)
Material:
Coal tar Emulsion Litre 0317 50.00 5 250.00
Soft Brush for painting - 25cm long Each 0314 33.00 1 33.00
Wire Brush - 25cm long Each 0313 15.00 1 15.00
Labour:
Mate (Skilled) Day 0002 609.00 1 609.00
Blacksmith - 1st Class (Skilled) Day 0008 609.00 1 609.00
Helper (Semi-skilled) Day 0021 505.00 1 505.00
Look Out Man (Un-skilled) Day 0033 431.00 1 431.00
Waterman (Un-skilled) Day 0034 431.00 1 431.00
Labour Unskilled Day 0020 431.00 15 6,465.00
Misc.:
T&P Lumpsum 9901 1.00 24 24.00
9,524.25
9,619.49
10,971.03
12,616.69
155022 Level crossing with CC block surface

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
8,231.25
8,313.56
9,481.62
10,903.86
Cost for 1 Sqm Sqm 275.32
155023 Level crossing with Morum/earth surface

Material:

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 1 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
6,507.25
6,572.32
7,495.73
8,620.09
155030 Removing and refixing of guard Rails over slab bridges during machine packing with
all contractor's men and materials duly removing fittings, leading guard rails to bridge
approaches, lifting, dragging, positioning and crossing of track etc, and as directed
by Engineer In charge.
Details of Cost for 100 Track Metre

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Crow bar, Hammer,box spanner, spanner,Rail tongs etc.) Lumpsum 9901 1.00 30.00 30.00
6,620.50
6,686.71
7,626.19
8,770.12
Cost for 100 Track Metres 8,857.82

Code (Rs.) (Rs.)
156000 6. Unimat Machine Related Works :
156010 Carrying out pre-tamping, during tamping and post-tamping works for tamping of
Turnouts of all types Under Traffic Block Conditions which include :(1) Re-
adjustment of ballast, heaping-up of ballast, filling-up of cavities in tamping zone by
picking ballast from stacks / shoulders / crib of adjoining track upto lead of 50 m to
ensure effective packing; (2) Clearing of ballast on sleepers to make them visible to
operator; (3) Clearing of ballast over rail foot to facilitate holding of rail by rollers of
UNIMAT; (4) Digging, screening and replenishment of ballast at mud pumping /
rounded ballast in sleeper crib location; (5) Tightening of loose fittings including
check rails immediately before & after tamping; (6) Replacement of broken / missing
fittings supplied by Railway; (7) Correcting displaced sleepers to position alongwith
squaring; (8) Re-setting worked-out / fallen fittings; (9) Removing and re-fixing
joggled fish plates & wooden blocks, OHE bonds & other obstructions, wherever
necessary ;(10) Removing and re-fixing stretcher bar, as directed; (11) Adjustment in
opening and housing of switch for testing operation of points (12)Manual
consolidation of ballast in cribs and shoulders; (13) Stages of payment a) 30% of the
rate will be paid on completion of pre tamping attention, b) Balance 70% of the rate
will be paid on completion of post tamping; (14) Recovery at the rate of twice the
applicable rate will be effected in case contractor fails to carry out any of the
pre/during/post operation.
156011 1 in 8½ Turnouts (Under Traffic Block Conditions)

Labour:
(i) Pretamping:-opening of the joggled plates, squaring & correcting sleeper
(ii) Attention to fittings
(iii) Filling of ballast in temping zone & other misc. works.
(iv) Removing, refixing stretcherbar, adjustment of opening & housing
Misc.:
5,330.00
5,863.00
5,921.63
6,753.62
7,766.66
156012 1 in 12 Turnouts (Under Traffic Block Conditions)

Labour:

Code (Rs.) (Rs.)
Misc.:
6,200.00
6,820.00
6,888.20
7,855.99
9,034.39

Labour:
Misc.:
8,060.00
8,866.00
8,954.66
10,212.79
11,744.71

Labour:

Code (Rs.) (Rs.)
Misc.:
8,501.00
9,351.10
9,444.61
10,771.58
12,387.32
156015 Derailing Switch (Under Traffic Block Conditions)

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
3,928.50
4,321.35
4,364.56
4,977.78
5,724.45
156020 Extra Over Item Numbers 156011 to 156015 for night block working
156021 Extra to Item no. 156011 for night block working

Take 15% of relevant item rate Set 156011 7844.33 0.15 1,176.65




Code (Rs.) (Rs.)
Take 15% of relevant item rate Set 156015 2890.85 0.15 433.63
156030 Carrying out pre-tamping, during tamping and post-tamping works prescribed in
current version IRTMM/IRPWM for tamping of Turnouts of all types Under
Conditions not requiring Traffic Block.
For newly assembled turnout on compacted and level ballast bed, precisely laid as
per layout drawing (s) with all new sleepers, fittings and other fixtures; many
activities are not required in comparison to that turnouts over under train operation.
Also there is no obstruction of traffic and no restriction of working hours as required
for work under traffic block, the cost is considered as 60% of the cost turnouts under
operation i.e. 60% of corresponding rates of item nos. 156010.
Rate as per item no. 156011 156011 7844.33 0.60 4,706.60

157000 7. Miscellaneous
157010 Carrying out various miscellaneous works, for proper upkeep of crew rest van / rest
room as directed by machine in-charge of Track Machines by providing a team of 2
labours for 12 hours shift, broadly mentioned hereunder:
(1) Bringing water from nearby source and cleaning machine with water jet or any
suitable means;
(2) Fuelling machine duly bringing diesel / hydraulic oil from the stacked drums;
(3) Bringing water to staff rest van or staff rest room, cleaning rest van / rest room,
cooking food for Track Machine staff or bringing food from outside;
(4) Guarding & watching machines, spare parts, oils, grease etc. during day and
night time at all locations, wherever necessary, as instructed by the machine in-
charge;
(5) Cooking food for Track Machine staff or bringing food from outside (cost of food
shall be borne by the staff concerned).
(6) In case, contractor provides less no. of Labour/Mate, payment will be deducted
for each such person @ 75% of the accepted item rate.
Details of cost for 1 shift

Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
872.00
880.72

Code (Rs.) (Rs.)
1,004.46

Code (Rs.) (Rs.)
1,155.13
Cost for 1 shift 1,166.68
Rate per shift per machine Shift 1,166.68
157020 Carrying out ancillary works required for UTV working under line block i.e., turning of
rails/ Sleepers and keeping in position for fixing of UTV clamps to rail, keeping
rails/PSC Sleepers in position while loading into BFR, removal of clamps on BFR for
releasing loaded rail/Sleepers, adjusting of rails/Sleepers on BFR etc. by providing
minimum of three men in a shift of 8 hours, with all contractor's tools, all lead, lift,
crossing of tracks etc., complete and as directed by the engineer - in - charge.
Note: In case, contractor provides less no. of Labour, payment will be deducted for
each such person @ 2/3 rd of the accepted item rate.
Cost for 1 shift of 8 Hrs

Labour:
Misc.:
1,303.00
1,433.30
1,447.63
1,651.03
1,898.68
Rate per shift Shift 1,917.67
157030 Providing lighting arrangements with halogen lamps on and around machine during
machine working in night time blocks, with contractors own generator, consumables,
all necessary electrical fittings, operators etc.
Note:
1. Lighting arrangement is to be provided as per advance planning of Night Blocks
and written communication.
2. In case lighting arrangement is made available but not used due to non-availability
of block, payment @ 60% of the item rate shall be made.
157031 BCM/FRM/UNIMAT (7.5 kVA generator and 12x500 W)

Detail of cost for per night
Materials :
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,604.00
2,630.04
2,999.56
3,449.49

Code (Rs.) (Rs.)
Cost for per night 3,483.99
Rate per night Night 3,483.99
157032 CSM / DUO / 3X with or without DGS (7.5 kVA generator and 8x500 W)
Detail of cost for per night
Materials :
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
Hire charges of 7.5 KVA Generator Day 0073 1000 1.00 1,000.00
2,444.00
2,468.44
2,815.26
3,237.54
Cost for per night 3,269.92
Rate per night Night 3,269.92
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 16: Small Track Machines
CHAPTER - 16 : Small Track Machines

Code (Rs.) (Rs.)
161000 1. Rails :
161010 Quick cutting with abrasive rail cutter of all types of rail sections including wear
resistant, head hardened rails upto 110 UTS, with contractors tools & plants,
equipment, consumable with all lead & lift etc. complete as directed by Engineer in-
charge. Abrasive Rail Cutter will be as per RDSO Specification No. TM/SM/1 (Rev.
01 of 2012) with latest status of RDSO; Rail Cutting Wheel Abrasive Disc will be as
per RDSO Specification No.TM/SM/2 (Rev. 01 of 2020)
161011 60 Kg - 110/90 UTS - Outside Track

Details of cost for 48 cuts.
Material:
As per RDSO SpecificaNo. TM/SM/2 Rev. 01 of 2007) number of cut per disc
is 6. Thus for 48 cuts, number of disc required = 48/6 = 8 nos.
Abrasive rail cutting disc as per RDSO's Spec. no. TM/SM/2 Each 0459 574.00 8.00 4,592.00
Driving belt (abrasive rail cutter) Each 0460 600.00 0.25 150.00
Labour:
Misc.:
T & P including consumables Lumpsum 9901 1.00 50.00 50.00
Hire charges of Abrasive Rail Cutter (without POL) Day 0143 300.00 1.00 300.00
7,351.00
7,424.51
8,467.65
9,737.80
161012 52 Kg - 90 UTS - Outside Track

Material:
As per RDSO SpecificaNo. TM/SM/2 Rev. 01 of 2007) number of cut per disk
is 7. Thus for 60 cuts, number of disk required = 60/7 = 8.5 nos. Say 9 nos.
Labour:
Misc.:
8,375.00
8,458.75
9,647.20
11,094.29

Code (Rs.) (Rs.)
161013 52 Kg - 72 UTS & other rails - Outside Track

Material:
is 12. Thus for 60 cuts, number of disk required = 60/12 = 5 nos.
Labour:
Misc.:
5,080.50
5,131.31
5,852.25
6,730.09
161014 60 Kg - 110/90 UTS - On Running Line

Material:
As per RDSO SpecificaNo. TM/SM/2 Rev. 01 of 2007) number of cut per disc
is 6. Thus for 48 cuts, number of disc required = 48/6 = 8 nos. However, due
to rail stresses as well as stress hardening, number of disk required is
considered more by 20% i.e. 8 x 1.20 = 9.6 Say 10 nos.
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
9,234.50
9,326.85
10,637.27
12,232.86
161015 52 Kg - 90 UTS- On Running Line


Code (Rs.) (Rs.)
Material:
is 7. Thus for 60 cuts, number of disk required = 60/7 = 8.5 nos. However,
due to rail stresses as well as stress hardening, number of disk required is
considered more by 20% i.e. 8.5 x 1.20 = 10.2 Say 10 nos.
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
9,487.00
9,581.87
10,928.12
12,567.34
161020 Cutting of rails with Rail Cutting Machine (Saw type) in all types of rail sections with
contractor's tools & plants, equipment, consumable with all lead & lift etc. complete,
as directed by Engineer in-charge. Rail Cutting Machine (Saw type) will be as per
RDSO Specification No. TM/SM/4, dated 24.04.1991.
Note: This item shall only be used in specific circumstances on specific order of
Engineer-in-Charge.

Details of cost for 11 cuts
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,490.00
2,514.90
2,868.24
3,298.48

Code (Rs.) (Rs.)
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,490.00
2,514.90
2,868.24
3,298.48

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,047.00
3,077.47
3,509.85
4,036.33
161024 52 Kg - 72 UTS & other rails - Outside Track

Material:
Labour:
Misc.:

Code (Rs.) (Rs.)
T&P Lumpsum 9901 1.00 10.00 10.00
3,047.00
3,077.47
3,509.85
4,036.33

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,705.50
2,732.56
3,116.48
3,583.95

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,705.50
2,732.56
3,116.48

Code (Rs.) (Rs.)
3,583.95

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,593.50
2,619.44
2,987.47
3,435.59
161030 Cutting of rails with electrically operated Rail Cutting Machine in all types of rail
sections, with contractor's tools & plants, equipment, consumable with all lead & lift
etc. complete, as directed by Engineer in-charge as per Specifications. Machine to
be fitted with monorail wheel arrangement and a handle of convenient height to
enable it to be pushed over one rail by one person to take it to the work-site.
161031 Outside track - When Electricity provided by static power supply of Railway :
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Electrically operated Rail Cutting Machine Day 0141 100.00 1.00 100.00
1,428.00
1,442.28
1,644.92
1,891.66
161032 On Running track - When Electricity provided by static power supply of Railway :

Code (Rs.) (Rs.)
Material:
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Electrically operated Rail Cutting Machine Day 0141 100.00 1.00 100.00
2,163.50
2,185.14
2,492.15
2,865.97
161040 Drilling holes of 16 mm to 32 mm dia. with Rail Drilling machine in all types of rail
section with contractor's tools & plants, equipment, consumable with all lead & lift
etc. complete, as directed by Engineer in-charge. Rail Drilling Machine will be as per
RDSO Specification No. TM/SM/3, dated 24.04.1991.
161041 Outside Track

Material:
Labour:
Misc.:
3,709.65
3,746.75
4,273.16
4,914.14
161042 On Running Line

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
4,749.65
4,797.15
5,471.15
6,291.82
161050 Drilling holes of specified size for bond holes with 7.2mm dia drill twist to correct
spacing and location on 60kg/52kg rails on cess or under traffic block with
contractor’s tools and plant, equipment, consumable, labour etc complete as
directed by the Engineer in charge at site.

Material:
Drill twist made of high speed of size 7.2 mm dia of Addison / I.T. make Each 0465 271.00 1.00 271.00
Normal unleaded Petrol Litre 0182 105 0.50 52.50
Labour:
Misc.:
T & P including consumables Lumpsum 9901 1 50.00 50.00
2,498.50
2,523.49
2,878.03
3,309.74
161060 Drilling holes of 16 mm to 32 mm dia. with electrically operated Rail Drilling Machine
in all types of rail sections, with contractor's tools & plants, equipment, consumable
with all lead & lift etc. complete, as directed by Engineer in-charge as per
Specification.
161061 Outside track - When Electricity provided by static power supply of Railway
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Electrically operated Rail Drilling Machine Day 0139 200.00 1.00 200.00

Code (Rs.) (Rs.)
2,491.54
2,516.45

Code (Rs.) (Rs.)
2,870.01
3,300.51
161062 On Running track- When Electricity provided by static power supply of Railway :
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Electrically operated Rail Drilling Machine Day 0139 200.00 1.00 200.00
2,922.54
2,951.76
3,366.48
3,871.46
161070 Bending & De-kinking with Hydraulic rail bender (Jim Crow) heavy duty in all types of
rail sections of flat bottom rails maximum upto 40mm with contractor's tools & plants,
equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-
charge. Hydraulic Rail Bender (Jim Crow) Heavy duty will be as per RDSO
Specification No. TM/SM/5, dated 08.05.1991.
161071 Outside Track

Details of cost for 40 bends
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Hydraulic Rail bender (Jim Crow) Day 0144 200.00 1.00 200.00
2,246.00
2,268.46
2,587.18
2,975.26
Cost for 40 bends 3,005.01
Rate per bend Each 75.13
161072 On Running Line


Code (Rs.) (Rs.)
Details of cost for 40 bends
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Hydraulic Rail bender (Jim Crow) Day 0144 200.00 1.00 200.00
2,677.00
2,703.77
3,083.65
3,546.20
Cost for 40 bends 3,581.66
Rate per bend Each 89.54
161080 Chamfering of drilled fish bolt holes in rails of any section and any UTS with
chamfering kit and with contractor's tools & plants, equipment, consumable with all
lead & lift etc. complete, as directed by Engineer in-charge. Chamfering Kit will be as
per RDSO's Specification No. TM-53 Rev. 01 of 2004.

Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,124.00
1,135.24
1,294.74
1,488.95
161090 Pulling of rail in LWR track by hydraulic rail tensor (Non-infringing type) under traffic
block for maintaining specified gap at rail joints for A.T. welding with contractor's
tools & plant, equipment, consumable with all lead & lift etc. complete, as directed by
Engineer in-charge. Hydraulic Rail Tensor (Non-infringing type) will be as per
RDSO's Specification No. TM/SM/32, dated 20.12.1991.
Details of cost for 8 gaps

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
Hire charges of Hydraulic Rail tensor Day 0146 150.00 1.00 150.00

Code (Rs.) (Rs.)
3,673.00
3,709.73
4,230.95
4,865.59
Cost for 8 gaps 4,914.25
Rate per gap Each 614.28
162000 2. Sleepers :
162010 Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with
as directed by Engineer in-charge. Hydraulic Sleeper Spacer shall be as per RDSO's
Specification No. TM/SM/17, dated 31.03.1992.

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Hydraulic Sleeper Spacer Day 0147 200.00 1.00 200.00
2,677.00
2,703.77
3,083.65
3,546.20
162020 Drilling of holes (vertically) into concrete sleeper in-situ for fixing guard rails and
check rails on concrete sleeper track at specified locations by concrete sleeper
drilling machine with contractor's tools & plants, equipment, consumable with all lead
& lift etc. complete, as directed by Engineer in-charge as per RDSO's Specification.

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,547.40
4,592.87

Code (Rs.) (Rs.)
5,238.17
6,023.90
162030 Loading / unloading of concrete sleepers from cess to BFR / BRH wagons and vice-
versa by jib crane attachable to BFR / BRH for handling concrete sleepers with
as directed by Engineer in-charge.
Detail of cost for 100 sleepers

Man Power:
Misc.
T&P Lumpsum 9901 1.00 50.000 50.00
Hire charges of Jib crane attachable and detachable to BFR/BRH Day 0158 300.00 1.000 300.00
1,643.00
1,659.43
1,892.58
2,176.47
162040 Quick removal of damaged concrete sleepers and restoration of railway track in case
of accidents / derailments and other such emergent situations by Concrete Sleeper
Breaker & angle grinder with contractor's tools & plants, equipments, consumable
etc. with all lead & lift complete, as directed by Engineer in-charge.

Labour:
Misc.:
Hire charges of Hammer Breaker Day 0148 200.00 1.00 200.00
2,822.00
2,850.22
3,250.68
3,738.28
163000 3. Fittings :

Code (Rs.) (Rs.)
163010 Measuring of Toe Load of ERC during service in field by Toe Load Measuring Device
(Mechanical) with contractor's tools & plants, equipment, consumable with all lead &
lift etc. complete, as directed by Engineer in-charge. Toe Load Measuring Device
(Mechanical) will be as per RDSO's Specification No. TM/SM/14 (Rev. 01 of 2005
with all updation).
Details of cost for 500 ERC


Code (Rs.) (Rs.)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Mechanical Toe load measuring device Day 0153 200.00 1.00 200.00
1,334.00
1,347.34
1,536.64
1,767.14
Cost for 500 ERC 1,784.81
163020 Measuring of Toe Load of ERC during service in field by Electronic Toe Load
Measuring Device with contractor's tools & plants, equipment, consumable with all
lead & lift etc. complete, as directed by Engineer in-charge. Electronic Toe Load
Measuring Device will be as per RDSO's Specification No.TM/SM/ETLMD/218 dated
13.9.2012.

Material:
Rechargeable Battery for ETLMD as per RDSO's Spec. no. TM/SM/ETLMD/218 Each 0463 1000.00 0.10 100.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Electronic Toe load measuring device Day 0154 200.00 1.00 200.00
1,494.00
1,508.94
1,720.95
1,979.09
163030 Extraction of jammed ERC by Heavy Duty Hydraulic Extractor with contractor's tools
& plants, equipment, consumable with all lead & lift etc. complete, as directed by
Engineer in-charge. Heavy Duty Hydraulic Extractor for jammed ERCs (10 Ton
capacity) shall be used as per RDSO's Specification No. TM/SM/6, dated 8.05.1991.

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
Hire charges of Heavy Duty Hydraulic Extractor (10 Tonnes) Day 0145 200.00 1.00 200.00
2,221.00

Code (Rs.) (Rs.)
2,243.21
2,558.38
2,942.14
164000 4. Miscellaneous :
164010 Tamping of track for picking up slacks in concrete sleeper track by Hand Held Off
Track Tamper (Power Pack Version) with contractor's tools & plants, equipment,
consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Off-
track tamper (Power Pack Version) will be as per RDSO Specification No.
TM/SM/OTT/320, dated 28.01.2009.

Material:
Man Power:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.
T&P Lumpsum 9901 1.00 50.00 50.00
Hire charges of off Track Tamper Day 0136 300.00 1.00 300.00
Hire charges of Generator 5 KVA (without POL) Day 0072 500 1.00 500.00
11,994.50
12,114.45
13,816.52
15,889.00
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 17: Handling of Materials
CHAPTER - 17 : Handling of Materials

Code (Rs.) (Rs.)
171000 1. Rails :
171010 Loading of rails of any section and length upto 13 metres in Wagons / Truck /
Trailor including lead upto 50 metres and lift upto 5 metres.
171011 In wagons during period of traffic block where handling by mechanical means is not
possible
Details of cost for 89 Metric Tonne (114 nos., 60 kg/m rails of 13 metre)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 60.00 60.00
14,461.00
15,907.10
16,066.17
18,323.47
21,071.99
Cost for 89 Metric Tonne 21,282.71
171012 In wagons not involving traffic block or on lines not opened to traffic but handling by
mechanical means is not possible
Details of cost for 133.38 Metric Tonne (171 nos. 60 kg/m rails of 13 metre)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 60.00 60.00
13,599.00
13,734.99
15,664.76
18,014.47
Cost for 133.38 Metric Tonne 18,194.61
171013 In Wagon under traffic block where mechanical handling is possible

Details of cost for 150 Metric Tonne (192 rails 13 metre 60 Kg)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
Lifting beam arrangement for handling of multi rails at a time Lumpsum 9901 1.00 150.00 150.00
15,931.00
16,090.31

Code (Rs.) (Rs.)
18,351.00
21,103.65
171014 In Wagon where mechanical handling is possible and traffic block is not required or
in Truck/Trailor.
Details of cost for 150 Metric Tonne (192 rails 13 metre 60 Kg)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
Lifting beam arrangement for handling of multi rails at a time Lumpsum 9901 1.00 150.00 150.00
11,707.00
11,824.07
13,485.35
15,508.15
171020 Loading of tongue rail, stock rail, switch assembly and crossings of any section and
length, SEJ,Glued joint etc. with / without P.way fittings and fastenings, in Wagon /
Truck / Trailor including lead upto 250 metre and lift upto 5 metre.
possible
Details of cost for 84 Metric Tonne
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
16,606.00
18,266.60
18,449.27
21,041.39
24,197.60
171022 In wagons not involving traffic block or on lines, not opened to traffic but handling by
mechanical means is not possible.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
12,296.00
12,418.96
14,163.82
16,288.40
171023 In Wagon where mechanical handling is possible and traffic block is required.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 100.00 100.00
16,312.00
16,475.12
18,789.87
21,608.36
in Truck/Trailor.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
12,950.00
13,079.50
14,917.17
17,154.75

Code (Rs.) (Rs.)
171030 Loading, leading and unloading of 52Kg / 60Kg rail upto 13 metre length by
Railway's Rail Dolly / Dip Lorry to the nominated location under traffic in case road
carriage is not possible with different lead with a lift upto 5 metre during block period.

Code (Rs.) (Rs.)
171031 For lead upto 500 metre.
Details of cost for 18.72 MT ( 24 Rails of 13 metre 60 Kg )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 28.00 28.00
4,516.00
4,561.16
5,202.00
5,982.30
Cost for 18.72 MT 6,042.13
171032 For lead beyond 500 metre and up to 1 Km.

Details of cost for 18.72 MT (24 Rails of 13 metre 60 Kg)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
5,821.00
5,879.21
6,705.24
7,711.02
Cost for 18.72 MT 7,788.14
171033 Extra to Items no. 171032 for lead beyond 1 Km for every subsequent Km or part
thereof and upto 10 Km
Details of cost for 18.72 MT ( Average Lead Considered 5 Km )
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
3,460.00
3,494.60
3,985.59
4,583.43
Cost for 18.72 MT for lead upto 5 Km 4,629.26
Cost for 1 MT for 5 Km 247.29
Rate per MT for 1 Km MT 49.46
171034 Extra to Item no. 171031 and 171032 with contractor's Rail Dolly / Dip Lorry

Code (Rs.) (Rs.)
Details of cost for 18.72 MT ( 24 Rails of 13 metre 60 Kg ) Required 6 Rail Dolly for
two groups. One taken as standby.
Misc.:
T&P Lumpsum 9901 1.00 5.00 5.00
Hire charges of Insulated Rail Dolly Day 0160 20.00 10.00 200.00
205.00
207.05
236.14
271.56
Cost for 18.72 MT 274.28
171040 Loading, unloading and hauling of 52Kg / 60Kg rail more than 13 metre and upto 39
metre length by Railway's Rail Dolly / Dip Lorry to the nominated location under
traffic in case road carriage is not possible for different leads and lift upto 5 metre.
171041 For lead upto 500m

Details of cost for 42.12 MT ( 18 no's 3 Rail Panels of 60 Kg )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
11,424.00
11,538.24
13,159.36
15,133.27
Cost for 42.12 MT 15,284.60
171042 For lead beyond 500 metre and up to 1 Km

Details of cost for 42.12 MT ( 18 no's 3 Rail Panels of 60 Kg )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 60.00 60.00
16,616.00
16,782.16
19,140.05
22,011.06
Cost for 42.12 MT 22,231.17

Code (Rs.) (Rs.)
Details of cost for 42.12 MT for lead upto 5 Km
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
10,364.00
10,467.64
11,938.34
13,729.09
Cost for 42.12 MT for lead upto 5 Km 13,866.39
Rate per MT per Km MT 65.84
171044 Extra to Item no. 171041 and 171042 with contractor's Rail Dolly / Dip Lorry
Details of cost for 42.12 MT
Misc.:
T & P ( Rs.5 for Each Rail Dolly ) Lumpsum 9901 1.00 60.00 60.00
340.00
343.40
391.65
450.39
Cost for 42.12 MT 454.90
171050 Unloading of rails of any section and length upto 13 metre, in neat manner for
Railway usage from departmental material train (DMT) or contractor's / Railway's
Truck/Trailor including lead upto 50 metre, lift upto 5 metre and stacking in
prescribed manner.
possible
Details of cost for 600 Metric Tonne ( 8 BFR's )
Labour:
Mate (Skilled) Day 0002 609.00 4.00 2,436.00
Look Out Man (Un-skilled) Day 0033 431.00 4.00 1,724.00
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
60,254.00
66,279.40
66,942.19
76,347.57
87,799.71

Code (Rs.) (Rs.)
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
46,106.00
46,567.06
53,109.73
61,076.19
in Truck / Trailor
Details of cost for 216 Metric Tonne ( 12 Trailors ) Two Road Crane required in a day
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
12,469.00
12,593.69
14,363.10
16,517.57
171060 Unloading of rails of any section and length from 13 metre to 39 metre, in neat
manner for Railway usage from departmental material train (DMT) including lead
upto 50 metre and lift upto 5 metre.
171061 During period of traffic block

Labour:
Mate (Skilled) Day 0002 609.00 4.00 2,436.00
Misc.:
T&P Lumpsum 9901 1.00 128.00 128.00
51,267.00
56,393.70
56,957.64

Code (Rs.) (Rs.)
64,960.18
74,704.21
171062 Not involving traffic block or in lines not opened to traffic

Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
37,486.00
37,860.86
43,180.31
49,657.36
171070 Unloading of all type of rails of length 130 metre and beyond from end unloading
rake and keep the panels in head-up position at specified distance from centre of
track clear from any infringement..
Note: Contractor has to keep Oxygen and Acetylene gas with cutter as standby
during the period of work.

Details of cost for 650 Metric Tonne ( 42 Panels of 20 Rails )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P including wire ropes,Oxygen,Acetelene gas with cutter etc. Lumpsum 9901 1.00 500.00 500.00
11,021.00
12,123.10
12,244.33
13,964.66
16,059.36
171072 Not involving traffic block

Details of cost for 650 Metric Tonne ( 42 Panels of 20 Rails )
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
Misc.:
T & P including wire ropes,Oxygen,Acetelene gas with cutter etc. Lumpsum 9901 1.00 500.00 500.00
10,159.00
10,260.59
11,702.20
13,457.53
172000 2. Sleepers :
172010 Loading of 52kg / 60kg PSC normal line and special sleepers upto 2.75 metre length
including existing fittings and fastenings in Depot / Station / Mid-section between
stations in a neat manner to departmental material train (DMT) or contractor's /
Railway's Truck/Trailer with crane or any other means including crossing of one track
with free lead upto 250 metre and lift upto 5 metre, if required with contractor's
labour, tools & plants, machinery, consumables etc.
possible
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Rail tongue, Crow bar etc.) Lumpsum 9901 1.00 160.00 160.00
11,113.00
12,224.30
12,346.54
14,081.23
16,193.42
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,054.00
14,194.54
16,188.87
18,617.20

Code (Rs.) (Rs.)

Labour:
Misc.:
13,520.00
13,655.20
15,573.76
17,909.82
in Truck / Trailor
Labour:
Misc.:
10,158.00
10,259.58
11,701.05
13,456.21
172020 Loading of 52kg / 60kg PSC line and special sleepers beyond 2.75 metre length
including existing fittings and fastenings in Depot / Station / Mid-section between
stations in a neat manner to departmental material train (DMT) or contractor's /
Railway's Truck/Trailor with crane or any other means including crossing of one track
with free lead upto 250 metre and lift upto 5 metre, if required with contractor's
labour, tools & plants, machinery, consumables etc.
possible
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
14,493.00

Code (Rs.) (Rs.)
15,942.30
16,101.72
18,364.02
21,118.62
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
22,638.00
22,864.38
26,076.83
29,988.35

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
16,256.00
16,418.56
18,725.37
21,534.17
172024 In Wagon/Truck / Trailor where mechanical handling is possible and traffic block is
not required.
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
Misc.:
12,894.00
13,022.94
14,852.66
17,080.56
172030 Loading, leading and unloading of PSC Sleepers of 52Kg / 60Kg by Railway's Rail
Dolly/ Dip Lorry to the nominated location under traffic in case road carriage is not
possible for different leads and lift upto 5 metres.
172031 For lead upto 500 metres

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,508.00
4,553.08
5,192.79
5,971.71
Cost for 24 MT 6,031.42
172032 For lead beyond 500 metre and up to 1 Km

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 30.00 30.00
6,673.00
6,739.73
7,686.66
8,839.66
Cost for 24 MT 8,928.06
Details of cost for 24 MT ( Average Lead Considered 5 Km )
Labour:

Code (Rs.) (Rs.)
Misc.:

Code (Rs.) (Rs.)
T&P Lumpsum 9901 1.00 12.00 12.00
3,460.00
3,494.60
3,985.59
4,583.43
Cost for 24 MT for lead upto 5 Km 4,629.26
Rate per MT per km MT 38.58
172034 Extra to Item no. 172031 and 172032 with contractor's Rail Dolly/Dip Lorry.
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
160.00
161.60
184.30
211.95
Cost for 18 MT 214.07
172040 Loading, leading and unloading of all types of P.Way fittings and all other
miscellaneous material except Rails, sleepers, switches, crossings, SEJs and Glued
Joints by road vehicles.
172041 Lead upto 5 Km

Consider the cost for 9 MT and average lead of 2.5 km
Cost of leading 2.5 km as per working sheet Tr.P.Way 443.75
Labour:
For loading and unloading considering 6 Beldars can load/unload a 9 MT truck in 1
hour. Therefore, no. of labour required for both loading and unloading = (1+1)/8 x 6 =
1.5 nos.
1,090.25
1,101.15
1,255.86
1,444.24
172042 Lead beyond 5 Km and upto 10 km

Labour:
1.5 nos.

Code (Rs.) (Rs.)
1,418.05
1,432.23
1,633.46
1,878.48

Consider the cost for 9 MT and average lead of 15 km
Cost of leading 15 km as per working sheet Tr.P.Way 1,213.57
Labour:
1.5 nos.
1,860.07
1,878.67
2,142.63
2,464.02

Labour:
1.5 nos.
2,393.28
2,417.21
2,756.83
3,170.36

Labour:
1.5 nos.
3,127.09

Code (Rs.) (Rs.)
3,158.36

Code (Rs.) (Rs.)
3,602.11
4,142.43
172046 Lead beyond 50 Km and upto 100 Km

Labour:
1.5 nos.
4,711.03
4,758.14
5,426.66
6,240.66

Labour:
1.5 nos.
7,097.92
7,168.90
8,176.13
9,402.55
172048 Extra for every Km per MT beyond 150 Km over item no. 172047
Considering only the additional cost of running beyond 150 km for a distance of 240
km with the following yardstick:
(i) Speed = 60 kmph,
Hiring time of truck = 240/60 = 4 hours = 0.5 day
(ii) Fuel consumption = 5 kmpl
Diesel consumption for 240 kms = 240/5 = 48 litres
Hire Charges of Truck - 9 tonne (without POL ) Day 0059 2000.00 0.50 1,000.00
5,877.76
5,936.54

Code (Rs.) (Rs.)
6,770.62
7,786.21
Cost for 9 MT for additional lead of 240 km 7,864.08
Rate per MT per km MT Km 3.64
172050 Transportation of Rails, sleepers, switches, crossings, SEJs and Glued Joints by
road vehicles.
Note: Loading and unloading shall be paid extra under relevant items.
172051 Lead upto 5 Km

443.75
448.18
511.15
587.82
Cost for 9 MT 593.70

771.55
779.27
888.76
1,022.07

Labour:
1,213.57
1,225.71
1,397.92
1,607.61

1,746.78

Code (Rs.) (Rs.)
1,764.25
2,012.13
2,313.95

2,480.59
2,505.40
2,857.41
3,286.02

4,064.53
4,105.18
4,681.95
5,384.25

6,451.42
6,515.94
7,431.43
8,546.14
172058 Extra for every Km per MT beyond 150 Km over item no. 172057
Considering only the additional cost of running beyond 150 km for a distance of 240
km with the following yardstick:
(i) Speed = 60 kmph,
Hiring time of truck = 240/60 = 4 hours = 0.5 day
(ii) Fuel consumption = 5 kmpl
Diesel consumption for 240 kms = 240/5 = 48 litres
Hire Charges of Truck - 9 tonne (without POL ) Day 0059 2000.00 0.50 1,000.00

Code (Rs.) (Rs.)
5,877.76
5,936.54
6,770.62
7,786.21
Cost for 9 MT for additional lead of 240 km 7,864.08
Rate per MT per km MT Km 3.64
172060 Unloading of 52kg / 60kg PSC line and special sleepers upto 2.75 metre length in
Depot / Station / Mid-section between stations in neat manner for Railway usage
from departmental material train (DMT) or contractor's / Railway's Truck/Trailer with
crane or any other means including crossing of one track and lead upto 250 metre &
lift upto 5 metre with contractor's labour, tools & plants, machinery, consumables etc.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
7,972.00
8,769.20
8,856.89
10,101.29
11,616.48
172062 Not involving traffic block or on lines, not opened to traffic

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P ( Rail tongue, Crow bar, etc. ) Lumpsum 9901 1.00 20.00 20.00
6,232.00
6,294.32
7,178.67
8,255.47

Code (Rs.) (Rs.)
172063 From Truck / Trailer
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,488.00
9,582.88
10,929.27
12,568.67
172070 Unloading of 52kg / 60kg PSC special sleepers beyond 2.75 metre length in Depot /
Station / Mid-section between stations in neat manner for Railway usage from
departmental material train (DMT) or contractor's / Railway's Truck/Trailer with crane
or any other means including crossing of one track and lead upto 50 metre & lift upto
5 metre with contractor's labour, tools & plants, machinery, consumables etc.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
10,121.00
11,133.10
11,244.43
12,824.27
14,747.91
172072 Not involving traffic block or on lines not opened to traffic

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
7,094.00
7,164.94

Code (Rs.) (Rs.)
8,171.61
9,397.36

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
9,876.00
9,974.76
11,376.21
13,082.65
172080 Spreading of New / SH PSC normal line sleepers from stack along track on either
side for different leads with all lifts by any means.
172081 For a lead upto 500m
Details of cost for 120 sleepers ( Average lead considered 250 metre )
Labour:
Misc.:
T & P ( Rail dolly, Rail tongue, Crow bar, etc. ) Lumpsum 9901 1.00 50.00 50.00
5,222.00
5,274.22
6,015.25
6,917.54
Cost for 120 sleepers for upto 500 metre Lead 6,986.71
172082 Extra to Item no. 172081 for additional lead of every 500m or part thereof beyond
500 m
Details of cost for 120 sleepers ( Average Lead considered beyond 250m beyond
500m )
Labour:
Misc.:
T & P ( Rail dolly, Rail tongue, Crow bar, etc. ) Lumpsum 9901 1.00 50.00 50.00
3,498.00
3,532.98
4,029.36

Code (Rs.) (Rs.)
4,633.77
173000 3. Miscellaneous Items :
173010 Unloading of Switches / Crossings / SEJ Rails / Glued Joints of any rail section and
length with or without P.Way fittings & fastenings in neat manner for Railway usage
from departmental material train (DMT) or contractor's / Railway's Truck/Trailer with
lead upto 250 metre & lift upto 5 metre -

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 32.00 32.00
10,123.00
11,135.30
11,246.65
12,826.81
14,750.83
173012 Not involving traffic block or on lines, not opened to traffic

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
8,818.00
8,906.18
10,157.50
11,681.12

Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:

Code (Rs.) (Rs.)
6,597.50
6,663.48
7,599.69
8,739.65
173020 Unloading all types of P.Way fittings and fastenings for Railway usage from Truck
and stacking with lead upto 250 metre & lift upto 5 metre.
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
1,744.00
1,761.44
2,008.92
2,310.26
173030 Collection and stacking of various P.Way materials at nominated stacking location
with serviceable and un-serviceable ones separately within a lead upto 500 metre
and lift upto 5 metre including crossing of track(s) wherever necessary as directed
by Engineer-in-Charge.
173031 Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
9,607.00
9,703.07
11,066.35
12,726.30
173032 All type of PSC sleepers

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 60.00 60.00
10,489.00
10,593.89
12,082.33
13,894.68
173033 P.Way fittings of all types and other similar loose items
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
9,700.00
9,797.00
11,173.48
12,849.50
173040 Stacking of glued joints in single layer for electrical testing, in such a manner that
glued joints - (a) shall not touch ground, (b) shall not touch one another, (c) shall not
touch any rail or any metallic body, (d) shall not be water-logged from any side and
(e) end post shall not rest on supports of glued joint

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P ( Crow bar, Rail tongue etc. ) Lumpsum 9901 1.00 24.00 24.00
5,805.00
5,863.05
6,686.81
7,689.83
Cost for 100 nos. 7,766.73
Rate per Glued Joint Each 77.67
173050 Un Loading of stone boulders weighing not less than 35 kg each from Railway
Wagons and stack at specificed locations with all contractor's tools & plants,
machinary, labour, lead and lift, crossing of track wherever necessary etc., complete
as directed by the Engineer Incharge.

Code (Rs.) (Rs.)
Un loading of boulders from railway wagons to specified locations
(20CuM*8wagons=160CuM)
Consider 10 Nos for each wagon
Labour:
Mate (Skilled) Day 0002 609.00 1 609.00
Misc.:
T&P ( No rate required) Lumpsum 9901 1.00 16.00 16.00
17,865.00
18,043.65
20,578.78
23,665.60
Cost for 160 CuM 23,902.26
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 18: Level Crossings
CHAPTER - 18 : Level Crossings

Code (Rs.) (Rs.)
181000 1. Dismantling
181010 Opening of level crossing upto required width from centre line of track for replacement
of sleepers by digging of pucca road surface up to bottom of sleeper, removing of
ballast, muck etc., screening of ballast & stacking the same near level crossing and
disposing of all debris, replacing the required sleeper duly packing the sleeper to
make fit for normal traffic and closing of LC surface with screened ballast to original
level by proper ramming and consolidation to smooth motarable surface as directed
Details of cost for 77 Sqm [ For Insertion of PSC Sleeper in LC Area required width for
dismantling of road surface is 3.5 metre from centre line of track ] Taken 11 metre
wide LC. i.e. { 11m x (3.5m + 3.5m) = 77 Sqm }
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 74.00 74.00
17,744.00
17,921.44
20,439.40
23,505.31
181020 Dismantling existing check rail of Level Crossing, blocks, bolts & nuts and stacking
these in a countable manner, as directed by Engineer in-charge.
Details of cost for 22 RM Taken 9 Metre wide LC For both side check rails {(9+ 2) x 2
= 22 Metre }
Labour:
For Dismantling and stacking of check rail
Misc.:
T&P Lumpsum 9901 1.00 14.00 14.00
2,510.50
2,535.61
2,891.86
3,325.64
181030 Dismantling exiting Rail Height Gauge carefully and stacking the released material in
acountable manner as directed by engineer in-charge including removal of cement
concrete foundation and making surface clean.
Details of cost for 2 No's of one LC

Code (Rs.) (Rs.)
Labour:
(i) For Removing existing ht. gauge
(ii) For making surface clean & handing over material to store etc.
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
4,582.00
4,627.82
5,278.03
6,069.73
Cost for 2 No's 6,130.43
Rate per Height Gauge Each 3,065.22
181040 Dismantling existing lifting barrier alongwith winch assembly and other components
like boom, fringes, locking arrangements, pedestal, boom rest, locking rods/wires,
pulley stakes, turn out wheels, 'A' base and other materials connected with
functioning of lifting barrier, removing engineering indicators on track and level
crossing raod signages without any damage including demolishing concrete base of
existing structures, filling, ramming and levelling the ground disturbed during
demolition, clearing debris and stacking all released material in a neat and countable
manner and clear of infringements, as directed.
Note: Barriers on both sides of level crossing constitute one set.
Details of cost 1 set

Labour:
(i) For dismentaling of foundation
(ii) For removing posts & Barrier
(iii) Leading all released material and stacking
(iv) Removing Engg Indicators
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 46.00 46.00
12,094.00
12,214.94
13,931.14
16,020.81
181050 Dismantling existing lifting barrier and other components except winch assembly, like
boom, fringes, locking arrangements, pedestal, boom rest, locking rods/wires, pulley
stakes, turn out wheels, 'A' base and other materials connected with functioning of
lifting barrier without any damage including demolishing concrete base of existing
structures and clearing debris in a neat and stacking in a countable manner and clear
of infringements, as directed.
Note: Barriers on both sides of level crossing constitute one set.

Code (Rs.) (Rs.)
Labour:
(i) For dismentaling of foundation
(ii) For removing posts & Barrier (except winch)
(iii) Leading all released material and stacking
(iv) Removing Engg Indicators
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 42.00 42.00
11,228.00
11,340.28
12,933.59
14,873.63
181060 Deduction to item no. 181050 for not dismantling ‘A’ base and its foundations
Labour:
(i) For dismantling of foundation and A base
Labour Unskilled Day 0020 431.00 -4.00 -1,724.00
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
-1,714.00
-1,731.14
-1,974.37
-2,270.52
Deduction for 1 set -2,293.23
Deduction per set Set -2,293.23
181070 Dismantling existing swing gate consisting of two leaves with gate posts, meeting post
and stopper post etc. without causing any damage to material and stacking the same,
as directed by Engineer in-charge.
Material:

Code (Rs.) (Rs.)
Labour:
(i) For dismentaling of wicked gate / swing gates
(ii) For removal of gate post, stopper etc. & stacking of released material
Misc.:
T & P including gas cutting equipments Lumpsum 9901 1.00 40.00 40.00
5,462.00
5,516.62
6,291.71
7,235.46
182000 2. Overhauling of Level Crossings :

182010 Overhauling of level crossing including digging out upto 50mm below sleeper,
screening of shoulder & crib ballast, replacing worn out sleepers & fastenings, check
rails as required including scrapping of rails and painting running rails and check rails
with two coats of coal tar emulsion, greasing of ERCs and liners as per IRPWM,
correcting cross level, gauge, alignment, surfacing and packing etc., re-inserting
screened ballast, making good deficient ballast with Railway's ballast from stacks /
heaps/borrowing from adjucent length of adjoining track, within 50m lead, ramming &
levelling road surface and refixing concrete slabs as required excluding re surfacing
with bitumen as directed by Engineer in-charge.
182011 Level crossings with asphalted road surface

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For removing of Black Top road surface
(ii) For removing ballast & other materials.
(iii) For Digging 50 mm below sleeper & screening etc.
(iv) For changing worn out sleeper, fittings & fastening etc.
(v) For filling good ballast, levelling, packing & prepairing of road surface etc.
(vi) For ramming of ballast on top surface
(vii) For coltaring of running & check rail etc.
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
14,317.00
14,460.17

Code (Rs.) (Rs.)
16,491.82
18,965.60
182012 Level crossings with concrete blocks road surface

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For removing of RCC slab/blocks
(iii) For Digging 50 mm below sleeper & screening etc.
(v) For filling good ballast, levelling, packing & prepairing of road surface etc.
(vi) For fixing of concrete slab including ramming
(vii) For painting of check rail and fixing joints of slabs etc.
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00
13,014.00
13,144.14
14,990.89
17,239.53
182013 Level crossings with any other type of road surface

Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For removing of Road surface

Code (Rs.) (Rs.)
(iii) For Digging 50mm below sleeper & screening etc.
(v) For filling good ballast, levelling, packing & prepairing of road surface
(vi) For ramming of ballast on top surface
(vii) For painting of check rail and making road surface etc.
Misc.:
T&P Lumpsum 9901 1.00 30.00 30.00
11,711.00
11,828.11
13,489.96
15,513.45
183000 3. Check Rail Related Works :

183010 Drilling of parabolic shaped holes to the web of check rail as per drawings &
specifications and as directed by engineer in- charge.
Details of cost for 38 nos.Holes
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,740.15
3,777.55
4,308.30
4,954.54
Cost for 38 nos.Holes 5,004.09

Code (Rs.) (Rs.)
183020 Fabrication including cutting & bending/machining and fixing of check rails of all rail
sections over PSC Sleepers as per Railway’s approved drawings & specifications for
level crossings / trolley paths/inspection lines in yards duly cutting rail flanges,
wherever required to correct alignment and level, drilling of holes with machine in
check rails and fixing to Running rail and sleepers with all Railway's fittings, e.g. rail
screws / grip expansion bolts, brackets, packing pieces, bolts, washers etc including
grinding of brackets if required,fixing of Railway's wooden blocks at flare ends duly
cutting and planing ,crossing of tracks and as directed by the engineer in-charge
Note:
1. Drilling of holes in PSC Sleeper and fixing of dowels shall be paid under relavent
item.
2. Required P.Way materials will be supplied at SSE/P.Way stores.
Details of cost for 9.10 TRM (18.20 RM )

Material:
Labour:
(i) For preparing flare end,cutting rail flange and fixing check rail with all fittings etc.
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
6,292.65
6,355.58
7,248.53
8,335.82
Cost for 9.10 TRM 8,419.17
183030 Cutting foot of rail by gas or any other approved method for check rails with
contractor’s tools & plants. Payment shall be made for length of cutting of foot.
Details of cost for 18.20 RM of Gas Cut (9.10 x 2.0 = 18.20 RM)
Material:
Labour:
Misc.:
1,785.00
1,802.85
2,056.15
2,364.57
Cost for 18.20 RM of Gas Cut 2,388.22

Code (Rs.) (Rs.)
183040 Fixing check rails to running rails on level crossings with MS brackets, MS packing
plates, bolts & nuts, spring washers etc. as per approved drawing & specifications, as
directed. Rails, MS brackets, packing plates, bolts & nuts, spring washers will be
supplied by Railways.
Note: One set consists two check Rails.
Details of cost for each set for 1 LC. Considering average length of chck rail as 7.50m
Labour:
Misc.:
T&P Lumpsum 9901 1.00 14.00 14.00
3,157.00
3,188.57
3,636.56
4,182.05
Rate oer Set Set 4,223.87
184000 4. Painting Works :

184010 Painting of running rails and check rails of any rail section of level crossing with anti
corrosive paint on web, foot etc etc., including liner contact area (excluding bottom of
foot) and fishing plane as per requirement with two coats of thickness of 100 microns
each by bituminous black paint confirms to IS-9862 of reputed make including
painting of liners,ERCs and including surface preparation, i.e. cleaning with wire
brush / sand paper as a complete job as per Para No 613 (2)(b)(iii) of Indian
Railways Permanent Way Manual, as directed by Engineer incharge.
Details of cost for 78 RM (Running rail + check rail = 4 x 12 + 4 x 7.5) (Considering

Double Line Track LC )
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,812.00
1,830.12
2,087.25
2,400.34
Cost for 78 RM 2,424.34
184020 Painting speed breakers with paint of approved quality & colour over the Bituminous
surface near approaches to level crossing.
184021 With enamel paint (two coats)

Code (Rs.) (Rs.)
Material:
Enamel Paint as per RDSO's Spec. no.M&C/PCN/120-2011 Litre 0306 190.00 8.00 1,520.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,749.00
2,776.49
3,166.59
3,641.57
184022 With luminous paint (two coats)

Material:
Luminous Paint as per RDSO's Spec. no. M&C/PCN/120-2011 Litre 0299 300.00 8.00 2,400.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,629.00
3,665.29
4,180.26
4,807.30
184023 With Hot melt thermoplastic road marking paint

Material:
Hot melt Thermo plastic road marking paint Litre 0298 160.00 10.00 1,600.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
Hire charges of Hot Paint machine Day 0135 150.00 1.00 150.00
2,979.00
3,008.79
3,431.52

Code (Rs.) (Rs.)
3,946.25
185000 5. Fencing and Gate Boom Related Works :

185010 Dismantling existing rail hurdle fencing including removal of base concrete and
stacking released materials in a neat and countable manner clear of infringements
from the track, removing debris clear of site alongwith disposing debris, as directed by
engineer in-charge within free lead of 250 metre & lift upto 5 metre complete with all
labour, tools & plants by contractor.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 42.00 42.00
9,828.00
9,926.28
11,320.92
13,019.06
Cost for 156 RM 13,149.25
185020 Dismantling existing whistle boards/Detonator Posts, including demolishing base

concrete and stacking released materials classification wise within free lead of 250
metre at location including clearing of debris,with contractor's labour, tools, vehicles,
consumables, all lead and lift etc., complete without damage as directed by the
Engineer-in-charge.
Note: While leading the dismantled debris for disposal the work may have to be
carried out by head loads and may involve crossing of existing tracks,and vehicles
may not reach the work spot directly. The rate provided include these elements of
work and no extra cost will be paid on this account. as directed by engineer in-charge
Details of cost for 20 Rail Post.

Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
2,334.00
2,357.34
2,688.55
3,091.83
Cost for 20 Rail Post 3,122.75
Rate per Rail Post Each 156.14

Code (Rs.) (Rs.)
185030 Providing Rail Height Gauge at approaches of level crossings as per approved
drawings in cement concrete foundation using Railway's rails of all sections including
cutting, bending, drilling holes, erecting in position with clamps, bolts & nuts including
painting with one coat of enamel paint of specified colour over one coat of primer.
Note: excavation and concrete work will be paid separately.
185031 (a) Less than 5 metre width of level crossing

Details of cost for 2 No's
Material:
Labour:
(i) For Leading of all materials
(ii) For Fixing
Misc.:
T&P Lumpsum 9901 1.00 32.00 32.00
14,204.40
14,346.44
16,362.12
18,816.44
Rate per Rail Height Gauge Each 9,502.30
185032 (b) Above 5 metre width of level crossing

Material:
Labour:
(i) For Leading of all materials
(ii) For Fixing
Misc.:
T&P Lumpsum 9901 1.00 40.00 40.00

Code (Rs.) (Rs.)
16,256.40
16,418.96
18,725.83
21,534.70
Rate per Rail Height Gauge Each 10,875.02
185040 Manufacture, supply, assembly, erection, commissioning and testing of Lifting Barrier
assembly, having fragmented boom, boom light boxes with suitable gate lamps, bell,
boom supports (stay wires) with adjusters, counter weight, pedestal and lock posts
with foundation of ‘A’ type as required, turn-union wheel with brackets, balance and
auxiliary weights clamps etc. to approved standard drawing nos. SA 7973 to 7980
with all fittings and fastenings complete with contractor's men, equipments and
materials, as per specifications and as directed (this item is excluding fringes).
185041 Upto 6m long Lifting Barrier

Material:
Lifting Barrier assembly for 6m long Lifting Barrier, having fragmented boom, boom set 0439 96858.59 1.00 96,858.59
light boxes with suitable gate lamps, bell, Boom supports (stay wires) with adjusters,
counter weight, pedestal and lock posts with foundation of ‘A’ type as required, turn
union wheel with brackets, balance and auxiliary weights clamps etc to approved
standard drawings to nos SA 7973 to 7980 with all fittings and fastenings complete
(excluding fringes)
Man Power : (For errection & Commissioning)

Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
99,359.59
100,353.18
114,452.81
131,620.73
185042 Above 6m and upto 8m long Lifting Barrier

Material:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
132,254.47
133,577.02

Code (Rs.) (Rs.)
152,344.59
175,196.28
185043 Above 8m and upto 10m long Lifting Barrier

Material:
light boxes with suitable gate lamps, bell, Boom supports (stay wires) with adjusters,
counter weight, pedestal and lock posts with foundation of ‘A’ type as required, turn
union wheel with brackets, balance and auxiliary weights clamps etc to approved
standard drawings to nos SA 7973 to 7980 with all fittings and fastenings complete
(excluding fringes)

Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
164,541.29
166,186.71
189,535.94
217,966.33
185050 Manufacture, supply, assembly, erection, commissioning and testing of Winch

Arrangement for operation of level crossing lifting barriers, as per RDSO’s approved
layout, having standard covering arrangement, foundation of ‘A’ type as required and
pulleys, pulley guides & stakes, horizontal rope wheel, vertical rope wheel, wire
adjusting screws, wire ropes 6 x 6 x 19 with all fittings, fixtures & accessories to
RDSO’s approved drawings with all parts including painting of steel work as per
specification, as directed with cement concreting complete {Excavation and concrete
work will be paid separately}

Material:
Winch arrangement for operation of level crossing lifting barriers, as per RDSO’s Each 0442 35289.90 1.00 35,289.90
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
38,739.90
39,127.30
44,624.68
51,318.38
Rate for each Each 51,831.57

Code (Rs.) (Rs.)
185060 Manufacture, supply, assembly, erection, commissioning and testing of auto boom
locking arrangement for existing lifting barriers, consisting of interlocking ground
frame near gate lodge, foundation of ‘A’ type, as required and connecting ground
frame to lock posts of gate booms with stipulated rodding on guide rollers, supported
on trestles including required excavation, foundation, providing RCC NP-2 Class
pipes of 100mm dia. for road / rail crossing, as per RDSO’s drawings complete
(Excavation, concrete work and NP-2 pipe will be paid separately).
185061 Single lever

Material:
Auto boom locking arrangement (Single lever) for existing lifting barriers, consisting of Each 0443 82481.50 1.00 82,481.50
interlocking ground frame near gate lodge, foundation of ‘A’ type as required and
connecting ground frame to lock posts of gate booms with stipulated rodding on guide
rollers, supported on trestles as per RDSO’s drawings complete (Excluding
excavation, concrete work)

Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
84,467.50
85,312.18
97,298.54
111,893.32
185062 Double lever

Material:
Auto boom locking arrangement (Double lever) for existing lifting barriers, consisting Each 0444 85105.91 1.00 85,105.91
of interlocking ground frame near gate lodge, foundation of ‘A’ type as required and
connecting ground frame to lock posts of gate booms with stipulated rodding on guide
rollers, supported on trestles as per RDSO’s drawings complete (Excluding
excavation, concrete work)

Misc.:
T&P Lumpsum 9901 1.00 15.00 15.00
87,601.91
88,477.93
100,909.08
116,045.44

Code (Rs.) (Rs.)
185070 Manufacture, supply and replacement of existing Railway's lifting barrier assembly
and boom supports of one side at level crossing including required excavation &
concreting foundation of ‘A’ type, as required for pedestal bases & fixing it on boom
supports, painting iron works with two coats of synthetic enamel paint over one coat
of red lead primer of approved quality & colour and setting lifting barrier for smooth
operation complete and as directed.
Note: Excavation & concrete work will be paid separately}

Material:
Railway's lifting barrier assembly of one side at level crossing Each 0445 80715.65 1.00 80,715.65
Man Power : (For Replcement & Commissioning)
Misc.:
T&P Lumpsum 9901 1.00 15.00 15.00
84,095.65
84,936.60
96,870.20
111,400.73
185080 Manufacture, supply and replacement of Railway's lifting barrier assembly and boom
supports, gate lamps at one side of level crossing including required excavation &
concreting foundation of ‘A’ type, as required for pedestal bases, including painting
iron works with two coats of synthetic enamel paint of approved quality and colour
over one coat of red lead primer of approved quality, setting lifting barrier for smooth
operation complete and as directed.
Note: Excavation & concrete work will be paid separately.

Material:
Railway's lifting barrier assembly and boom supports, gate lamps, of one side at level Each 0446 84751.43 1.00 84,751.43
crossing
Man Power : (For Replcement & Commissioning)
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
88,745.43
89,632.88
102,226.30
117,560.25


Code (Rs.) (Rs.)
186010 Manufacturing, supplying and laying at specified locations factory made CC block
pavers for road surface of level crossings to RDSO Drg.No. M.00003, manufactured
using 20mm size graded hard stone aggregates of approved quality with all
contractor's cement, labour, tools/plant and curing with all lead & lift as per
specifications and as directed by Engineer in-charge.
186011 80mm thick blocks of M-35 grade for medium traffic.

Material:
Precast CC Paver block -80mm thick M35 grade Sqm 0454 495.00 10.50 5,197.50
Concedering 5% wastage i.e. 10 + 0.5 = 10.5 Sqm
Labour:
Misc.:
7,124.50
7,195.75
8,206.75
9,437.76
186012 120mm thick blocks of M-40 grade for heavy traffic.

Material:
Precast CC Paver block -120mm thick M40 grade Sqm 0455 774.00 10.50 8,127.00
Concedering 5% wastage i.e. 10 + 0.5 = 10.5 Sqm
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
10,363.00
10,466.63
11,937.19
13,727.77
Rate per Sqm Sqm 1,386.50
186020 Fixing of Railway’s precast concrete slabs of different sizes in position for level
crossings / trolley path and filling gap between check rail / running rail, slabs,
approaches etc. with asphalt complete and as directed.
Details of cost for 84.36 sqm {7.20 x 1.30 + 2 x(7.50 x 5.0)}
Material:
Coal tar Emulsion Litre 0317 50.00 20.00 1,000.00
Fuel wood Quintal 0345 4000.00 0.20 800.00

Code (Rs.) (Rs.)
Labour:
(i) Leveling between check rail & approaches
(ii) Leading precast slab & fixing
(iii) Ashphalting
Misc.:
T&P Lumpsum 9901 1.00 32.00 32.00
9,043.00
9,133.43
10,416.68
11,979.18
Cost for 84.36 Sqm 12,098.97
186030 Paving of level crossing road surface with Railway's precast RCC slab / blocks as per
standards / approved drawings for light and heavy vehicles, supplied on bed of sand,
moorum or gravel, duly compacted and joints filled with mixture of sand & tar/bitumen
in proportion of 1:2 by weight.
Details of cost for 84.36 sqm {7.20 x 1.30 + 2 x(7.50 x 5.0)}

Material:
Fine Sand (Zone IV) Cum 0203 1000.00 2.00 2,000.00
Bitumen Hot sealing compound : Gr. A MT 0319 28000.00 0.05 1,260.00
Fuel wood Quintal 0345 4000.00 0.25 1,000.00
Labour:
(i) For leveling of ballast bed
(ii) For leading & fixing of RCC slab / Paver blocks
Misc.:
T&P Lumpsum 9901 1.00 36.00 36.00
12,670.00
12,796.70
14,594.64
16,783.83
Cost for 84.36 Sqm 16,951.67
186040 Removal of RCC slab in existing level crossing portion and in between tracks
alongwith stacking them in countable manner, as directed.
Labour:

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,303.00
1,316.03
1,500.93
1,726.07
186050 Fixing of speed breaker on approaches of level crossings with pre-cast concrete
blocks (M-25) of parabolic shape for entire road width with 125 mm central rise, 2m
wide in the middle including painting two coats with paint of approved quality and
colour.
Details of cost for 15 Running Metre

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,828.00
3,866.28
4,409.49
5,070.92
186060 Provision of one Asphalt Speed Breaker Rumble Strip on each side of the approaches
of manned level crossings as per approved drawing including painting two coats with
paint of approved quality and colour
Details of cost for 15 Running Metre
Material:
Bitumen Hot sealing compound : Gr. A MT 0319 28000.00 0.06 1,680.00
Fuel wood Quintal 0345 4000.00 0.50 2,000.00
Labour:
Misc.:
T & P including tray for heating asphalt Lumpsum 9901 1.00 50.00 50.00
7,578.50
7,654.29
8,729.71

Code (Rs.) (Rs.)
10,039.17
186070 Manufacture & supply of tested GI wire rope of 6mm dia. and 6 ply to suit lifting barrier
gates at nearby P.Way Stores / Depot / Level Crossing gate, as directed.
Details of cost 100 Kg

Material:
GI wire rope of 6mm dia. 6 ply to suit lifting barrier gates Kg 0447 350.00 100.00 35,000.00
Misc.:
35,000.00
35,350.00
40,316.68
46,364.18
Cost for 100 Kg 46,827.82
186080 Supplying and fixing of Boom Supports (stay wires) for lifting barrier (approx. 8mm
dia.) with suitable adjuster and other specials, as directed
Detail of cost for 4 no's
Material:
Boom Supports (stay wires) for lifting barrier (approx. 8mm dia) Each 0448 1000.00 4.00 4,000.00
Man Power : (For Fixing)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
5,124.00
5,175.24
5,902.36
6,787.72
Cost for 4 no's 6,855.59
186090 Manufacture and supply of vertical / horizontal Turnout Wheels and Shafts, mounted
over base plate weighing not be less than 6 Kg with supporting vertical base, made of
MS angle 75mm x 75mm x 10mm as per Railway's approved drawings and
specifications complete and as directed.

Material:
Vertical / Horizontal Turnout Wheels and Shafts mounted over the base plate Each 0451 1320.00 1.00 1,320.00
Misc.:
1,320.00
1,333.20
1,520.51
1,748.59

Code (Rs.) (Rs.)
186100 Manufacturing and supplying to site of work including installation pulley with pulley
stakes complete, wire rope 6 x 6 x 19 with accessories as per Railway’s approved
drawings for operation of lifting barriers complete, as directed.

Material:
Pulley with Pulley stakes complete, wire rope 6x6x19 ply with accessories as per Each 0450 347.00 10.00 3,470.00
Man Power : (For Installation)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
4,594.00
4,639.94
5,291.85
6,085.63
Cost for 10 no's 6,146.49
Rate for each Each 614.65
186110 Fabrication, supply and fixing of Fringes to the lifting barriers of various length at level
crossing as per approved drawing; made of MS flat of size 30mm x 6mm in 2 rows,
40mm x 6mm in 1 row horizontally and MS flat of size 30mm x 6mm vertically at
500mm centre to centre, painting iron works with two coats of synthetic enamel paint
of approved quality & colour over one coat of red lead primer of approved quality, as
directed.
Details of cost for 18.20 RM (9.10 x 2.0 = 18.20 RM)

Horizontal M.S. Flat reqd = 3 nos.
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
12,168.00
12,289.68
14,016.38
16,118.84
Cost for 18.20 RM 16,280.03
186120 Supplying and driving into ground 'C' class G.I. pipes of 20mm dia. x 150mm length
for planting red flags and lamp at 5 metre on both sides from the centre of road at
level crossings with all leads & lifts. Payment shall be made for complete work at one
Level Crossing.
Note: Two pipes make one set.
Details of cost for each LC

Labour:

Code (Rs.) (Rs.)
Misc.:
Pipe and T & P @ 30% of labour cost. 78.00
338.00
341.38
389.34
447.75
Rate per LC Set 452.22
186130 Manufacturing & supplying to site of work and installing Turnout wheel - Horizontal
Rope Wheel - double wire (2-way) including guides with all contractor's materials,
fabrication, labour, T&P, consumables, all leads & lifts etc. complete as per approved
drawing and as directed by Engineer in-charge.

Material:
Turnout wheel- HORIZONTAL ROPE WHEEL double wire (2 way) including guides Each 0452 2024.00 20.00 40,480.00
Man Power : (For Installation)
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
41,604.00
42,020.04
47,923.86
55,112.43
Cost for 20 no's 55,663.56
186140 Supplying galvanized Steel Wire Rope for DW signalling 6 x 19 ply as per IRS No.
S.11 amended upto date for lifting barrier at level crossing gates, as directed by
Engineer in-charge
Details of cost 100 Kg
Material:
Galvanized STEEL WIRE ROPE for DW signalling 6 x 19 ply as per IRS No. S.11 Kg 0453 250.00 100.00 25,000.00
Misc.:
25,000.00
25,250.00
28,797.63
33,117.27
Cost for 100 Kg 33,448.44
186150 Fabrication, supplying and fixing Stop Boards of 600mm dia. to lifting barriers as per
approved drawing, made of 3mm thick plate, using MS clamps, providing 6 nos. of
50mm dia. red reflector on stop board, painting iron works with two coats of synthetic
enamel paint over one coat of red lead primer of approved quality & colour and writing
STOP mark over the board.

Disc volume = 4 x 22/7 x (0.6 x 0.6)/4 x 0.003 = 0.00085 cum, weight = 26.68 Kg
Material:

Code (Rs.) (Rs.)
4" dia round ceramic Light Reflector as per specification Each 0449 350.00 24.00 8,400.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
12,344.00
12,467.44
14,219.12
16,351.98
16,515.50
186160 Manufacturing, supplying and fixing Wicked Gate of size 1025mm x 1025mm x
1000mm at manned level crossings, as per approved drawing including painting with
2 coats of specified enamel colour paint over 1 coat of primer including earthwork in
excavation etc. complete, as per specifications and as directed.
Details of cost for 1.5 MT {Mild steel plates/sheets/angles required for one wicket gate
is approx 0.15 MT}
Material:
2062
Labour:
Misc.:
T&P Lumpsum 9901 1.00 44.00 44.00
117,652.00
118,828.52
135,523.93
155,852.52
Cost for 1.5 MT 157,411.04
186170 Fixing of wooden blocks of approximate size of 150mm x 300mm x 1200mm on end of
check rails including sizing at level crossings with contractor's labour, tools & plants
and as directed.
186171 With Railway’s wooden block by cutting Railway’s wooden sleepers (supplied free by
Railways) into blocks by sawing to size
Labour:

Code (Rs.) (Rs.)
(i) Cutting of wooden blocks from sleepers ( 1 carpenter + 1 helper prepare 20 Blocks
(ii) Fixing of wooden blocks
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 28.00 28.00
7,175.00
7,246.75
8,264.92
9,504.66
186172 With Contractor’s hard wood block

Material:
Volume of 1 no. Wooden Block (size : 1.20m x 0.3m x 0.15m) = 0.054 cum
Volume for 40 nos. = 40 x 0.054 cum = 2.16 cum = 2160 Cudm
Labour:
(i) Fixing of wooden blocks
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
81,657.00
82,473.57
94,061.11
108,170.27
Cost for 40 nos 109,251.98
186180 Fixing of grip expansion bolts of 18mm / 22mm dia. with nuts and MS clips / washers
on PSC sleepers as per specifications for fixing guard rails / check rails / trolley path
including drilling of required holes in sleepers with all fittings with contractor's tools &
plants, equipment, consumables with all lead, lifts etc. complete, as directed by
Engineer in-charge, excluding cost of bolts, nuts, washers, clips etc.

Material:
Labour:
(i) Fixing of grip expansion bolt & nut with MS clip and washer for guard rail/check rail
(ii) For PSC sleeper drilling holes for fixing of nut & bolt

Code (Rs.) (Rs.)
Misc.:
T&P Lumpsum 9901 1.00 22.00 22.00
Hire charges for pillar drilling machine Day 0138 1000.00 0.50 500.00
6,907.20
6,976.27
7,956.44
9,149.90
Cost for 80 nos. 9,241.40
186190 Erecting detonator rail posts at required locations as required including cutting the rail
to required length varying from 1.00M to 1.50M , leading the rail pieces from
nominated station / mid section from nearest depot to site of work, erecting the rail
post by making the pit size as required and filling with CC 1:3:6 mix with 40mm metal
and painting the rail post with two coats of synthetic enamel paint of approved colour
and make, with contractor's materials, labour, paint, all lead and lifts,etc., complete as
per specifications and as directed by the Engineer-in-charge.
Note: Excavation and concrete work for foundation will be paid under relavent item

Material:
Sand Paper Nos. 0496 5.00 6.00 30.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
(i) Fixing of Rail Post, Painting etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P for cutting torch Lumpsum 9901 1.00 50.00 50.00
5,513.00
5,568.13
6,350.45
7,303.02

Code (Rs.) (Rs.)
186200 Errecting Emergency Chain Posts for level crossings , including cutting rail to required
length varying from 1.00M to 1.50M , drilling holes, providing hooks & links / rings with
necessary locking arrangements to fix emergency chain, leading the rail pieces from
nominated station / mid section from nearest depot to site of work, erecting the rail
post by making the pit of size as required and filling with CC 1:3:6 mix with 40mm
metal and painting the rail post with two coats of synthetic enamel paint of approved
colour and make, with contractor's materials, labour, paint, all lead and lifts,etc.,
complete as per specifications and as directed by the Engineer-in-charge.
Note:
(1) Rails & chain will be supplied by Railways.
(2) Excavation and concrete work for foundation will be paid under relavent item.

Material:
Sand Paper Nos. 0496 5.00 6.00 30.00
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
(i) Fixing of Rail Post, Painting etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P for cutting torch Lumpsum 9901 1.00 50.00 50.00
6,722.00
6,789.22
7,743.11
8,904.57
186210 Providing Rail Barricading with rails supplied by Railways with verticals provided at
every 1.5m interval, height of barricade being upto 1.5m above ground / termination
level and one or more row of horizontal rail, duly cutting rails and drilling holes as
required, assembling necessary accessories to required length, including earthwork
excavation for foundation, fixing posts in cement concrete 1:3:6 base of size 0.45m x
0.45m x 0.60m and one coat of red oxide painting of steel work.
Note:
1. Excavation and concrete work will be paid separately.
2. Rail shall be made available within 250 metres
Details of cost for 15 MT ( For 100 RM Barricading by 52 Kg Rails )

Material:
Labour:
(i) Fixing of fencing
Mate (Skilled) Day 0002 609.00 1.00 609.00

Code (Rs.) (Rs.)
(ii) Carting of rail
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iii) Painting of rail
Misc.:
24,232.80
24,475.13
27,913.88
32,100.97
Cost for 15 MT 32,421.98
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 19: Bridge Related Activities
CHAPTER - 19 : Bridge Related Activities

Code (Rs.) (Rs.)
191000 1. Dismantling Works :
191010 Dismantling existing track on girder bridges including guard rails and foot path etc.,
cutting existing SW panels / LWR, if required into free rails of not less than 12 metre
length and leading all released materials to nominated place within 50m of bridge
approaches and stacking the released materials clear of infringements, as per
direction of Engineer-in-Charge.
Note: Rail cutting and drilling shall be paid separately.
191011 Under Traffic Block Conditions

Labour:
(i) Opening fittings of running rails, guard rails & pathway
(ii) Removing of running rails, guard rails,Sleepers & pathway
(iv) Leading of rails, guard rails, sleepers fitting & stacking etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail tounge, Spanner,Rollers etc.) Lumpsum 9901 1.00 100.00 100.00
13,029.00
13,680.45
13,817.25
15,758.58
18,122.37
191012 Under Conditions not requiring Traffic Block.

Labour:
(i) Opening fittings of running rails, guard rails & pathway
(ii) Removing of running rails, guard rails,Sleepers & pathway
(iv) Leading of rails, guard rails, sleepers fitting & stacking etc.
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
11,305.00
11,418.05
13,022.29

Code (Rs.) (Rs.)
14,975.63
191020 Insertion of temporary girder in place of formation involving dismantling of track,

removal of ballast and neatly stacking for future use, excavation & installation of CC
crib or wooden crib at both ends as per approved design in one or more traffic blocks,
excavation for creating space for insertion of girder as required, placement of girder
by contractor’s Crane, tools & plants, filling of earth/sand filled bags at different
stages as required, linking of track and connecting with the approaches, ballasting,
boxing and packing approach sleepers to make track fit for 20 kmph to the
satisfaction of Engineer in-charge.
Note:
1. The CC Cribs as required and Temporary Girder shall be supplied by Railways.
2. The charges for wooden sleepers/blocks required for matting and bearing as per
approved design shall be paid extra as per relevant item.
3. In case bridge timber / channel sleepers are required to be laid on girder, the same
shall be paid separately under relevant item.
191021 RH /Temporary girder of length varying from 12.2m to 16.3m using road crane
capacity of 80 tons
Details of cost for 1 span
Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Removing ballast, Slewing track by road crane
(ii) Excavation formation, installation of crib for insertion of girder
(iii) Placement of girder by road crane
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Jacks, Spanner etc.) Lumpsum 9901 1.00 48.00 48.00
60,919.00
63,964.95
64,604.60
73,681.55
84,733.78
Rate per Span Each 85,581.12

Code (Rs.) (Rs.)
191022 RH /Temporary girder of length above 16.3m and up to 26.00 using Road crane
capacity of 100Tons.
Details of cost for 1 span

Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
(i) Removing ballast, Slewing track by road crane
(ii) Excavation formation, installation of crib for insertion of girder
(iii) Placement of girder by road crane
Misc.:
129,168.00
135,626.40
136,982.66
156,228.73
179,663.04
191030 Manufacturing and using wooden sleepers/blocks required for matting and bearing as
per approved design for use below and above CC Crib for insertion of Temporary
Girder.
Note: The item is for one time use and released wooden sleepers/blocks shall be the
property of the Contractor.
Wooden Blocks required for matting and bearing at both ends on top and bottom
considering size of 3.6m x 3 m = 4 x 3.6 x 3.0 x 0.30 = 12.96 cum = 12960 cudm.
Assuming these wooden block can be used 50 times, quantity to be taken for one
time use = 12960/50 = 259.20 cudm
9,162.72
10,450.08
12,017.59
Cost for 12960 Cudm 12,137.77

Code (Rs.) (Rs.)
191040 Removal of temporary girder, crib on both ends and placing temporary girder on crib
/ cess away from Railway track as directed by engineer at site under traffic block;
filling of Railway's earth by ramming, pulling ballast from stack / adjoining track /
same track, laying track, linking with approach track and packing of ballast for
opening track at 20 kmph speed, boxing & dressing of cess, ballast profiling etc.
Note: If earth is to be brought by contractor from outside, the same will be paid
separately.
191041 RH /Temporary girder of length varying from 12.2m to 16.3m using road crane
capacity of 80 tons
Details of cost for 1 set of RH girder
Material:
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) Removal/Slewing of girder including crib & placing on crib/cess away from track by
road crane
(ii) Filling earth,ramming,laying & linking of track
(iii) Filling ballast,packing,levelling,aligning,boxing & dressing of track
Misc.:
64,865.00
68,108.25
68,789.33
78,454.23
90,222.37
191042 RH /Temporary girder of length above 16.3m and up to 26.00 using Road crane
capacity of 100Tons
Details of cost for 1 set of RH girder
Material:
Labour:
Mate (Skilled) Day 0002 609.00 2.00 1,218.00

Code (Rs.) (Rs.)
(i) Removal/Slewing of girder including crib & placing on crib/cess away from track by
road crane
(ii) Filling earth,ramming,laying & linking of track
(iii) Filling ballast,packing,levelling,aligning,boxing & dressing of track
Misc.:
86,999.00
91,348.95
92,262.44
105,225.31
121,009.11
192000 2. Linking of Track over Girders :

192010 Removing existing Channel/H-Beam sleepers with fittings from the running track
under traffic block for TBTR & stacking the same neatly at specified places with
contractor’s tools & labour, as directed by Engineer in-charge.
Details of cost for 80 sleepers (For Removing Channel sleeper one group of 4
persons will remove 16 sleepers in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 52.00 52.00
12,729.00
14,001.90
14,141.92
16,128.86
18,548.19
192020 Extra to item no. 192010 for Track Circuited area including handling of released PVC
washers on bolts and extra rubber pads on sleepers
Work involves handling of released PVC washers on bolts and extra rubber pads on
sleepers

Code (Rs.) (Rs.)
Labour:
Misc.:
T&P Lumpsum 9901 1.00 5.00 5.00
867.00
875.67
998.70
1,148.51
192030 Inserting in track Steel Channel/H-beam sleepers with all Railway supplied fittings
complete for TBTR work to specified gauge under traffic block with contractor’s tools
including aligning, levelling to make track fit for 20 kmph speed and as directed by
Engineer in-charge.
Note: Transportation of track material if supplied beyond 250m of bridge appraches,
shall be paid seperately under relevant item.
Details of cost for 84 sleepers (For carting & inserting Steel Channel Sleepers one
group of 4 persons will insert 12 sleepers in a day)
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
(i) For inserting sleeper with fixing fittings etc.
(ii) For guaging, aligning, levelling etc.
Misc.:
T&P Lumpsum 9901 1.00 64.00 64.00
15,579.00
17,136.90
17,308.27
19,740.08
22,701.09
192040 Extra to item no. 192030 for Track Circuited area including handling of released PVC
washers on bolts and extra rubber pads on sleepers.
Work involves providing PVC washers on bolts and extra rubber pads on sleepers
Labour:
Misc.:
T&P Lumpsum 9901 1.00 14.00 14.00
1,738.00
1,755.38

Code (Rs.) (Rs.)
2,002.01
2,302.31
192050 Complete Track Renewal on Bridge with Steel Channel/H-beam sleepers as per
approved drawings including leading of running and guard rails, sleepers and fittings,
bending of guard rails, drilling of holes, cutting of rails etc. and leading the released
rails, slepeers & fittings near bridge approaches under traffic block as directed and
making track structure fit for normal speed.
Note:
1) Rails, Steel Channel/H-beam sleeper and all fittings will be supplied by Railways.
2)Transportation of track material if supplied beyond 250m of bridge appraches, shall
be paid seperately under relevant item.
Detail of cost for 50 TRM

Material:
Epoxy for fixing HDPE dowel, Rubber Pads as per RDSO approved specification Kg 0321 500.00 1.00 500.00
Labour:
(i) Leading Channel sleepers, running Rails & Guard Rails ,fittings over the bridge
and leading back the released rails & fittings to bridge approaches over the bridge

(ii) Fixing Channel sleepers alongwith fittings
(iii) Fixing rail with Fitting Clips
(iv) Fixing Guard rail
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail tounge, Spanner etc.) Lumpsum 9901 1.00 116.00 116.00
33,066.30
36,372.93
36,736.66
41,898.16
48,182.88

Code (Rs.) (Rs.)
193000 3. Casual Renewals Works :

193010 Renewal of existing cracked /broken/corroded isolated Steel Channel/H-beam
sleepers with Railway supplied steel channel sleeper with its fittings during traffic
block by removing the guard rail and foot path plates with its fittings and loosening of
adjacent sleepers hook bolts and lifting of track to required height for removal of old
sleeper and insertion of new steel channel sleeper with all fixtures and GR/ER pad
in position to neat gauge without disturbing alignment of the track as a whole using
with contractors own non infringing jacks and labour ,consumables, wooden
packings and refixng back in position guard rails and foot path plates alongwith
fittings and tightening of loosened hook bolts etc as a complete job as directed by
Engineer incharge at site. The rate includes trucking of new steel channel sleepers
and its fittings from bridge approaches and trucking back released steel channels and
its fittings to bridge approaches/ nominated locations.
193011 Broad Gauge Track

Material:
Drill Bit (32 mm & 26.5 mm dia) Each 0470 300.00 2.00 600.00
Synthetic Rubber based Adhesive Litre 0320 200.00 1.00 200.00
Labour:
(i) Removal of fittings,Lifting and supporting of track on wooden packings,(Lifting
batch)
Mate (Skilled) Day 0002 609.00 1.00 609.00
ii) Renewal batch ( Removal of old sleeper and insertion of new sleeper and lowering
of track )
Mate (Skilled) Day 0002 609.00 1.00 609.00
iii)Fittings fixing batch and Positioing and Punching of holes in E/R pads
Misc.:
T&P(Crow bar, tami bar, beater, hammer, Rail dolly,Spanner etc.) Lumpsum 9901 1.00 88.00 88.00
Hire charges for pillar drilling machine Day 0138 1000.00 1.00 1,000.00
Hire charges of Hydraulic jack 8/10 Tonnes capacity Day 0104 300.00 1.00 300.00
21,460.10
23,606.11
23,842.17
27,192.00
31,270.80

Code (Rs.) (Rs.)
193020 Renewal of existing running rail and guard rails of all sections on bridge portion over
Steel Channel sleepers/PSC sleepers under traffic block including leading of new
rails,fittings, refixing all the fastenings as per approved drawings including cutting of
rails, drilling of holes to running and guard rails,as required as per drawing and
leading back the released rails and fittings and stacking at nominated place clear of
infringements with all leads & lifts tools and consumables complete and as directed.
Material:
Labour:
(i) Leading new running Rails & Guard Rails and fittings on to bridge and carting back
released materials and stacking
(ii) Fixing rail with Fitting Clip
(iii) Fixing Guard rail
Mate (Skilled) Day 0002 609.00 2.00 1,218.00
Misc.:
T & P (Crow bar, Rake ballast, Auger, Beater, Spanner, Hammer etc.) Lumpsum 9901 1.00 72.00 72.00
21,391.40
23,530.54
23,765.85
27,104.95
31,170.69
Rate of TRM TRM 629.65
193030 Scattered renewal or replacement of missing / worn-out fittings of channel sleeper on

Bridge with Railway's fittings including leading to required location for the work and
the released fittings shall be collected and neatly stacked as directed by Engineer
incharge.
193031 Involving Rubber Pad

Details of cost for 100 nos. sleeper
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
3,638.00
3,674.38

Code (Rs.) (Rs.)
4,190.63
4,819.22
193032 Not involving Rubber Pad

Details of cost for 100 nos. sleeper
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
2,038.50
2,058.89
2,348.16
2,700.38
194000 4. Guard Rails related Work :

194010 Manufacture of flared portion of Guard Rail by cutting and bending to required shape
& RDSO’s approved drawings.
Note:
(1) Rails shall be supplied by Railways.
(2) One set consists of two rails i.e. both left and right.
Details cost for 2 set (Two flare rail L.H.+ R.H.)

Material:
Labour:
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail dolly, Spanner etc.) Lumpsum 9901 1.00 36.00 36.00
5,131.00
5,182.31
5,910.42
6,796.99

Code (Rs.) (Rs.)
194020 Providing and fixing of flared portion of guard rails of any rail section over PSC
sleepers including fixing of with all fittings, including leading of rails and fittings,
squaring and adjusting spacing of sleepers as required, providing nose blocks duly
cutting wooden blocks supplied by railways and fixing it with bolts of 16mm dia as
directed complete and finished as per RDSO’s approved drawing.
Note:
1.One set consists of LH & RH side rails of one end.
2.Required P.Way fittings will be supplied at SSE stores depot.
Details cost for 2 set (Two flare rail L.H.+ R.H.)

For putting back, flared guard rail at approach of bridge
Labour:
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail dolly, Spanner and for cutting wooden Lumpsum 9901 1.00 80.00 80.00
4,642.00
4,688.42
5,347.14
6,149.21
194030 Drilling holes 25mm to 40mm dia. with drill twist in the foot of guard rails for fixing
guard rails on bridge as directed.
Details cost for 80 nos.
Material:
Labour:
Machinist (operator) (Skilled) Day 0040 609 1.00 609.00
Misc.:
T & P (Crow bar, tami bar, beater, hammer, Rail dolly, Spanner etc.) Lumpsum 9901 1.00 10.00 10.00
3,813.65
3,851.79
4,392.96
5,051.91
Cost for 80 nos. 5,102.43
194040 Drilling of 25mm to 40mm dia. holes in PSC sleepers with suitable rotary hammer /
drilling machine at indicated location for fixing of guard rails on bridges & its
approaches as per approved drawing and fixing of HDPE dowels with adhesive of
approved quality to Drawing no. RDSO/T-3002, procured from RDSO's approved
sources with contractor’s materials and consumable.

Code (Rs.) (Rs.)
Material:
HDPE Dowels Each 0456 100.00 80.00 8,000.00
Labour:
Misc.:
T & P (Crow bar, Tomi bar, Spanner etc.) Lumpsum 9901 1.00 10.00 10.00
15,097.15
15,248.12
17,390.48
19,999.05
194050 Renewal of existing guard rails of all rail sections on bridge portion over
wooden/PSC/steel channel sleepers excluding flared ends duly leading new guard
rails including cutting of rails,drilling holes to the guard rails as required and as per
drawings,refixing with all fastenings,and leading back the released rail, stacking at
nominated place clear of infringements with all leads & lifts complete and as directed.

Material:
Labour:
(i) Leading Guard Rails on to bridge and carting back releasedrails and stacking

(ii) Renewal & Fixing Guard rail
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Crow bar, Rake ballast, Auger, Beater, Spanner, Hammer etc.) Lumpsum 9901 1.00 20.00 20.00
7,222.60
7,294.83
8,319.75
9,567.71

Code (Rs.) (Rs.)
194060 Dismantling of existing flared portion of guard rails of any rail section over PSC
sleepers duly removing rails & fastenings and leading and stacking released
materials at nominated place within free lead, clear of infringements, complete and as
directed.
Note: One set consists of LH & RH side rails of one end.

Labour:
(i) Opening fittings,removing rails,Leading of guard rails, fittings & stacking etc.
Mate (Skilled) Day 0002 609.00 0.50 304.50

Misc.:
2,595.50
2,621.46
2,989.77
3,438.23

195010 Fabrication & supply of Galvanized Steel Channel Sleepers made from ISMC 150mm
x 75mm / 175mm x 75mm / 200mm x 75mm standard rolled section conforming to
IS:2062 as per RDSO approved drawing No 1636/R1/R2 with latest correction slips
complete and as directed by Engineer Incharge.
Note: Cost of Steel fittings and GRSP shall be paid separately
Detail of cost for 1 MT

Total = Channels + plates = 155.046kg
including wastage 5% i.e. 1.55+ 0.0775 = 1.6275 Qtl.
Add for Rivets and welding @3% 0.03 280.20
Fabrication charges
Labour:
Dip Galvanisation @ 705gm / sqm ( 100 Microns thick ) MT 0436 17000.00 0.16 2,635.00
14,483.10
Misc:
Sundries for rivetting,drilling,T&P and consumables @ 3 percent on total labour & 0.03 434.49
materials
14,917.59
15,066.77
17,183.65
19,761.19
Cost for 1.55 Qtls 19,958.81
Rate per Qtl. 12,876.65

Code (Rs.) (Rs.)
195020 Fabrication & supply of Galvanized H-beam Sleepers made out of the materials
confirming to IS 2062 of standard Rolled sections as per approved drawing Nos
RDSO/B/1636/4/R,5&9 complete and as directed by Engineer-incharge.
Note: Cost of steel fittings and GRSP shall be paid separately.

Total = H-Beam + plates = 168.351 kg
including wastage 5% i.e. 168.351 + 5% of 168.351=176.76 Kg
Add for welding @ 1% 0.01 101.42
Fabrication charges
Man power
14,822.52
Misc:
Sundries for rivetting,drilling,T&P and consumables @ 2 percent on total labour & 0.02 296.45
materials
15,118.97
15,270.16
17,415.62
20,027.96
Cost for 1.68 Qtls 20,228.24
Rate per Qtl. 12,040.62
Cost for 1MT MT 120,406.20
195030 Supply of 25mm thick new rubber pads of RDSO drawing no B/1636/I/R2 from
approved sources of RDSO and replacement with old crushed rubber pads of 10mm
thickness and fixing by approved adhesive on steel channel sleepers on bridges
complete, as directed by Engineer In-charge.
Details of cost for 100 Channel sleepers ( Each sleeper having 2 Rubber pads ) i.e.
Material:
Supply of 25/30 mm thick Elastomeric Pad as per RDSO drawing No. B/1636/I/R2 Each 0432 152.00 200.00 30,400.00
Poly chloroprene rubber based solvent (toluene free) to prevent working out of rubber Kg 0492 2000.00 1.00 2,000.00
pads
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 24.00 24.00
39,319.00
39,712.19
45,291.75
52,085.52
Cost for 200 nos. 52,606.37

Code (Rs.) (Rs.)
195040 Supplying & fixing MS chequered plates 6 to 8mm thick between guard rails on un-
ballasted deck bridge for gang pathway, overlapping at regular intervals of 2m to
2.5m with rail screws or bolts duly drilling holes in chequered plate, as directed
Note: Overlapping of chequered plates shall not fall in between sleepers.
Details of cost for 1000 Kg

Material:
Mild steel chequered plate MT 0247 42500.00 1.05 44,625.00
( Add wastage 5 %, so quantity = 1050 Kg
Man Power : For Fixing
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
Hire charges for pillar drilling machine Day 0138 1000.00 1.00 1,000.00
58,234.20
58,816.54
67,080.27
77,142.31
Cost for 1000 Kgs. 77,913.73
195050 Providing staging during traffic block to 3.6 m x 3.0 m x 3.0 m approx. size using
steel cribs and/or wooden sleepers as per RDSO’s approved drawing, duly
excavating earth in pit and driving rails / sleepers vertically to form shoring and filling
gap with sand bags etc. complete, as directed.
Note:
(1) Steel CC cribs, rails and wooden sleepers will be supplied by Railway.
(2) Dismantling and linking of track will be paid separately.

Labour:
(i) For preparing staging by steel cribs & wooden sleeper and fixing of clamps
(iii) Form shoring and filling sand bags
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Rake ballast, Beater, Rail tongue etc.) Lumpsum 9901 1.00 54.00 54.00
13,667.00
13,803.67
15,743.09
18,104.55

Code (Rs.) (Rs.)
195060 Fixing of Railway's gang-way / landing slabs of size Slab (size 0.5 x 1.0 x 0.05 m)
without damaging slab edges with proper concrete packing and fixing with cement
jointing in running traffic condition without block complete and as directed.

Slab (size 0.5 x 1.0 x 0.05 m) = 0.025 cum
Labour:
(i) Leading of slab for path way
(ii) Fixing of slab for way
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T & P (Crow bar, Tami bari etc.) Lumpsum 9901 1.00 38.00 38.00
4,273.00
4,315.73
4,922.09
5,660.40
Cost for 20 RM 5,717.01
195070 Clearing waterway of major & minor bridges by removing weeds / shrubs / bushes,
removing silt deposit, filling scours, if any upto 10 metre from centre of bridge on
either side including disposing waste and silt away from waterway.
Note: Rate is for a single line and per metre of bridge span.
Details of cost for 40 Metre span

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
5,370.00
5,423.70
6,185.73
7,113.59
Cost for 40 Metre span 7,184.73
195080 Fabrication, supplying and fixing 600mm x 450mm Bridge Board made from 16 SWG
MS Sheet duly welded or rivited to back support of two 600mm long horizontal angles
of size 25mm x 25mm x 3mm & two 2.5 metre long vertical support of MS Angle of
size 50mm x 50mm x 5mm, welded / rivited to board. Vertical supports shall have split
ends for proper fixing in ground. Vertical supports of board shall be embedded in
ground in M 20 Cement Concrete blocks of size 300mm x 300mm x 300mm,
complete job including painting & writing of subject matter on bridge board, as
directed by Engineer - Incharge
Note: Excavation & concrete work will be paid separately.

Code (Rs.) (Rs.)
Details of cost for 10 Boards
Required MS sheets size (600mm x 450mm & 16 SWG thick) For 10 boards 10 x
(0.6m x 0.45m x 0.001626m) = 0.0043902 cum, Density of MS steel is 7860 Kg/Cum,
Hence Weight of MS Sheet is = 0.0043902 x 7860 = 34.51 Kg, Required M.S.Angle
of size (25 x 25 x 3mm ) for 10 boards 12 metre long, Volume = 12 x (0.025 + 0.025)
x 0.003 = 0.0018 cum. Required M.S.Angle of size(50 x 50 x 5mm) 50 metre long,
Volume = 50 x (0.05 + 0.05) x 0.005 =0.025 cum Total Volume = 0.0018 + 0.025 =
0.0268 cum, Hence Weight of MS Angles = 0.0268 x 7860 = 210.65 Kg, Total weight
of MS Steel = 34.51 + 210.65 = 245.158 Kg or 2.46 quintal.
Material:
2062
Man Power (for fabricating) :
Man Power (for fixing) :
Misc.:
T&P Lumpsum 9901 1.00 18.00 18.00
23,210.00
23,442.10
26,735.72
30,746.07
Rate per Board Each 3,105.35
195090 Shallow screening of track on ballasted deck slab bridge i.e. screening of crib ballast
and shoulder ballast in between sleeper ends and ballast retaining walls on both
sides of the track without disturbing core under the sleeper under traffic following all
safety precautions and othe instructions prescribed by Engineer in-charge. Muck
should be disposed of away from bridge upto a maximum distance of 350 m and lift
upto 10m.
Details of cost for 50 TRM (One group of 4 persons deputed for 5 track metre length)
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
18,446.50
18,630.97
21,248.62
24,435.91

Code (Rs.) (Rs.)
195100 Bending the inner and outer 52 Kg/60Kg/90R rails availble at site suitable for V
portion along bulb of rerailing ramp as per RDSO Drg No T-8259 drilling of holes and
cutting to the required length and shape all lead, lifts, labour, tools and plants
machinery and all other required materials for bending etc, and as directed by
Engineer Incharge at site.
Details of cost for 1 set of 52 m length

A team of 8 men can complete the whole set i.e. 52mts length of rails bending and
giving curvature to the inner and outer 52 Kg/60Kg/90R rails suitable for V Portion
and approach guiding rails of re railing ramp in 6 days (6x8=48)
Labour:

Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
Hire charges of Hydraulic bending machine to bend the rails including fuel and Day 0155 1100.00 6.00 6,600.00
Hire charges of Furnace blower to heat the rails for bending purpose including fuel Day 0156 300.00 6.00 1,800.00
and operator
30,650.00
30,956.50
35,305.89
40,601.77
195110 Supplying providing and fixing country kali wood/hard wood (Non teak) sleepers of
various thickness and length as per the RDSO re railing ramp Drg No T-8259 for
fixing bent rails and MS plates including cutting the wood in saw mills, transporting to
site of work with all leads and lifts, labour, tools and plant etc. as directed by Engineer
In-charge.
Cost of 2.0 cum i.e. 2000 Cudm

Material:
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
Hire charges for wood sawing machine including fuel and operator Day 0157 1500.00 0.25 375.00
70,425.00
71,129.25
81,122.91
93,291.35
Cost of 2000 Cudm 94,224.26
Rate per Cudm Cudm 47.11

Code (Rs.) (Rs.)
195120 Fixing of 60Kg/52 Kg/90R rails for Re railing ramp as per RDSO Drg No T-8259 on
bridge approaches on wooden/PSC sleepers including fixing railways fishplates,
bolts, nuts, MS bearing plates, screws, check blocks of re-railing ramp etc, levelling
after drilling of holes in rails wherever necessary under block with contractor's
labour,tools and plants,machinary all etc,complete and as directed by Engineer
incharge at site.
Details of Cost for one set of rails of length 52 mts

8 men can complete the whole set in 3 days ie, 52mts length of rails laying and fixing
60/52Kg/90R rails under Trafiic block.
Man Power
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
11,873.00
11,991.73
13,676.57
15,728.05
Rate per Set Each 15,885.33
195130 Tightening of steel channel sleeper fittings i.e. hook bolts, running rails bolts, guard
rail bolts on girder bridges with contractor labour tools, plants etc., including oiling,
greasing of fittings complete and as directed by engineer in charge.
Note: Before execution of work specific approval of ADEN to be obtained by duly
indicating the locations with speciic reasons along with date of last tightening done.
Details of cost for 100 sleepers. Each sleeper requires 35 gms of grease
Material:
Cotton Jute Kg 0494 40.00 2.00 80.00
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,010.00
3,040.10
3,467.23
3,987.32
Rate per sleeper Sleeper 40.27
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 20: Supply of P.Way Materials
CHAPTER - 20 : Supply of P.Way Materials

Item no. Description Unit Rate Rate (Rs.) Quantity Amount
Code (Rs.)
201000 1. Bridge Related Fittings
201010 Manufacture and supply of Hook Bolt 28mm dia. & 320mm long as per RDSO Drg.
no. BA-1636/I/R2 from RDSO approved sources
Detail of cost for 1no.
Material:
Hook Bolts 28mm dia & 320mm long as per RDSO's drg. No. BA-1636/I/R2 Each 0437 35.00 1.00 35.00
Misc.: 35.00
39.92
45.91
201020 Manufacture & supply of 10mm thick Grooved Rubber Pads as per drg. No. RDSO/T-
5199 & RDSO's Spec. no. IRS-T-47-2006 (Prov.) from RDSO approved sources to
IRS specification with all contractor's lead, lift, labour, tools, plant and transportation
etc. complete as instructed by Engineer in-charge.
Note: One set constitutes two nos.
Detail cost for 1 set

Material:
10 mm thick Grooved Rubber Pads as per drg. No. RDSO/T-5199 & RDSO's Spec. Each 0429 132.00 2.00 264.00
no. IRS-T-47-2006 (Prov.)-1989
264.00
301.09
346.26
Rate for each Set 349.72
201030 Manufacture & supply of Elastomeric Pads 25mm / 30mm thick as per RDSO drawing
No. B/1636/I/R2 to suit Insulated steel channel sleepers from RDSO approved
sources with all contractor's material, lead, lift, labour, tools, plant and transportation
etc. complete as per approved drawings and as instructed by Engineer in-charge.
Note: One set constitutes two Nos.

Material:
Supply of 25/30 mm thick Elastomeric Pad as per RDSO drawing No. B/1636/I/R2 Each 0432 152.00 2.00 304.00
304.00
346.71
398.72
Rate per Set Set 402.71
201040 Manufacture & supply of a set of 2 Nos of Elastomeric Pads 25mm / 30mm thick and
4 nos of Grooved rubber pads as per RDSO drawing No. B/1636/5 alt 2 to suit
Insulated H Beam sleepers from RDSO approved sources with all contractor's
material, lead, lift, labour, tools, plant and transportation etc. complete as per
approved drawings and as instructed by Engineer in-charge.
Note:
One Set consists of 2 nos. Elastomeric Pad 25mm/30mm and 4 nos. Grooved Rubber
Pad


Code (Rs.)
Material:
Supply of 2 nos. Elastomeric Pad 25mm/30mm and 4 nos. Grooved Rubber Pad as Set 0433 1650 1.00 1,650.00
per RDSO drawing No. B/1636/5/Alt 2
1,650.00
1,881.83
2,164.10
201050 Manufacturing and supplying Galvanised MS Inner and Outer Clips for Steel Channel
Sleeper (RDSO Drg. No. T-6150 & T-6151) from RDSO approved sources{One set
constitutes two inner & two outer clips}
Material:
Galvanised MS liner and Outer Clip for steel channel sleeper (RDSO Drg. No. T- Set 0434 434.00 1.00 434.00
6150 & T-6151)
434.00
494.98
569.22
201060 Manufacture, supply & fixing of galvanised steel fittings of insulated galvanised steel
channel sleeper for 60 Kg running rails & 52 Kg Guard Rail as per RDSO drawing no.
RDSO/T-5155 to 5164 with up-to-date correction slips and specifications from RDSO
approved sources with all contractor's lead, lift, labour, tools, plant, transportation etc.
complete as per approved drawings and instructions of Engineer in-charge.

Material:
Galvanised steel fittings for insulated galvanized channel sleepers (52/60 kg rail) as set 0431 2000.00 1.00 2,000.00
per RDSO drawing no. RDSO/T-5155 to 5164
2,000.00
2,281.00
2,623.15
201070 Manufacture, supply & fixing of galvanised steel fittings of insulated galvanised steel
channel sleeper for 52Kg running rails & 52 Kg/90R Guard Rail as per RDSO drawing
no. RDSO/T-5197 to 5200 with up-to-date correction slips and specifications from
RDSO approved sources with all contractor's lead, lift, labour, tools, plant,
transportation etc. complete as per approved drawings and instructions of Engineer in-
charge.

Material:
Galvanised steel fittings for non insulated galvanized channel sleepers (52/60 kg rail) set 0430 1534.00 1.00 1,534.00
as per RDSO drawing no. RDSO/T-5197 to 5200
1,534.00
1,749.53
2,011.96

Code (Rs.)
201080 Supplying of Zero toe load fixtures for each H Beam sleepers of 52/60Kg Rails
procured from RDSO approved firms as per RDSO approved drawing with up-to-
date correction slips and specifications with all contractor's lead, lift, labour, tools,
plant, transportation etc. complete as per approved drawings and instructions of
Engineer in-charge.
Note: Complete fixture for 1 sleeper shall constitute 1 set.
Detail cost for 1 Set

Material:
Zero toe load galvanised fixtures for H Beam sleepers of 52/60kg Rails as per Set 0438 3000 1.00 3,000.00
RDSO approved drawing
3,000.00
3,421.50
3,934.73
Rate per sleeper Set 3,974.07
202000 2. Different Components of Track :

202010 Manufacture and Supply of Single Coil Spring Washer T-10773 as per RDSO Drg.
No. RT-4015 from RDSO approved sources at Store of SSE/P.Way complete and as
directed.
Detail cost for 1 no.
Material:
Single Coil spring washers T-10773 Each 0435 4.35 1.00 4.35
4.35
4.96
5.71
202020 Manufacturing & supplying linked chain made of 8mm dia. rods with joints welded
with links of length not exceeding 40mm with ring & bolt at one end and hook &
locking arrangement at other end, painted with two coats of PO red paint of various
length of 5.5 m to 11 m of approved quality, as directed.
Details of cost for 140 Metre chain {8mm dia rods per metre weight = 0.39 kg/metre}
For 140 metre long chain required double length i.e.280 x 0.39 = 109.20 Kg or 1.10
Quintal + 0.20 quiantal for hooks & locking arrengements.
Material:
MS Bolts & Nuts below 10mm dia Kg 0251 60.00 2.00 120.00
Man Power :
Misc.:
T&P Lumpsum 9901 1.00 20.00 20.00
12,102.00
13,802.33

Code (Rs.)
15,872.68
203000 3. Level Crossing Indicator Boards, Engineering Indicators, Curve Boards etc :
203010 Manufacturing, fabricating and supplying retro-reflective Level Crossing Indicator

boards, made of 2mm thick aluminum sheet or 3mm thick aluminium composite
sheet, face to be fully covered with high intensity encapsulated type heat activated
retro-reflective sheeting conforming to type-IV of ASTM-D4956-01 in yellow & black or
other colour combination including subject matter, message, symbols, borders etc.
as approved by Engineer In-charge or as per IRPWM guidelines, pasted on substrate
by an adhesive backing which shall be activated by applying heat and pressure
conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized
aluminium alloy rivets @ 20 cm c/c to back-support frame of M.S. angle iron of size
25mm x 25mm x 3mm alongwith theft resistant measures, mounted and fixed with 2
nos. M.S. angles of size 35mm x 35mm x 5mm to a vertical post made up of M.S. Tee
section ISMT 50mm x 50mm x 6mm, back side of board shall be with non-peelable
weather-proof paint, consisting of one coat of zinc chromate primer and two coats of
epoxy paint. Vertical post shall have black & white anti-corrosive paint or powder
coating complete, as directed.
203011 Bilingual Whistle Boards for level crossing

Detail of cost for 2 boards of size (60cm x 60cm) = 0.72 sqm (fixing on one post
having length 3950mm)
Material:
Aluminum Sheet / Strips of various sizes & thickness Kg 0245 200.00 4.50 900.00
Aluminum sheet @ 6.23 kg/sqm
High intensity retro-reflective sheet Sqm 0476 1625 0.76 1,235.00
Considering 5% wastage i.e 0.72 + 0.036 = 0.756 Sqm
Rivets (different sizes) for miscellaneous works. Kg 0233 54.50 0.25 13.63
Man Power:
Misc:
T & P (Including cost of materials for drilling holes nuts bolts etc.) Lumpsum 9901 1.00 50.00 50.00
4,891.63
5,578.90
6,415.73
203012 Speed Breaker / Rumble Strips Board

Detail of cost for 2 boards one board of equilateral triangular shape having each side
of 900mm with support length of 3650mm other board of size ( 60 x 20cm) fitted on
the same support as above. So Area of board's is = 0.35 + 0.12 = 0.47sqm
High intensity retro-reflective sheet Sqm 0476 1625 0.49 796.25

Code (Rs.)
Man Power:
3,878.68
4,423.63
5,087.17
203013 Un-manned Level Crossing Danger Stop Board
Detail of cost for one board of size (675mm x 525mm) with support length of
3650mm. So Area of board = 0.354sqm
Material:
Man Power:
3,203.55
3,653.65
4,201.70
Cost for 1 board set 4,243.71
203014 Manned Level Crossing Indicator Board

Detail of cost for 2 boards one board of equilateral triangular shape having each side
of 900mm with support length of 3650mm other board of size ( 90 x 30cm) fitted
vertically on the same support as above. So Area of board's is = 0.35 + 0.27 =
0.62sqm
Material:
2062

Code (Rs.)
Man Power:
4,403.88
5,022.62
5,776.01
203015 Single Strip / Double Strip Level Crossing Road Warning Board
Detail of cost for one board of size ( 675 x 525mm) with support length of 3650mm.
Material:
Man Power:
Misc:
3,203.55
3,653.65
4,201.70
203016 Manufacturing and supply of circular STOP Disc of 600mm dia for fixing on
emergency chains at level crossings as given in IRPWM including providing Retro
reflective sheet fully covered over board confirming to type-IV of ASTM-D4956 in red
back ground colour and text "STOP" of white colour over back ground.The circular
board shall consists of 2mm thick Aluminium sheet fixed to 1.5mm thick MS Sheet of
600mm dia with suitable sized aluminium alloy rivets @ 20 cm c/c to back-support
.Retro reflective sheet is to be pasted on substrate by an adhesive backing which
shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-
4956-01.A vertical holding stand of 1000 mm length x15mm thick to be jointed to back
side of board along with a hook for fixing emergency chain as directed by Engineer
Incharge.
Detail of cost for one Stop Disc of Circular shape having diameter of 600mm with
support length of 1000mm. So Area of board is = 0.283sqm + wastage 25% for
circular shape = 0.36 Sqm
Material:
High intensity retro-reflective sheet Sqm 0476 1625.00 0.38 617.50
Structural Steel Plates conforming to Grade Designation E 250; Quality "A" as per IS Quintal 0223 6300.00 0.06 378.00
2062

Code (Rs.)
11.78 kgs per sqm 11.78x.36= 4.24 kgs
MS Round 1000mmx15mm=0.016=1.60kg 4.24+1.60=5.84kgs
Man Power:
Misc:
2,618.70
2,986.63
3,434.62
Rate per Board Each 3,468.97
203020 Manufacturing, fabricating and supplying retro-reflective Engineering Indicator boards,

made of 2mm thick aluminum sheet or 3mm thick aluminium composite sheet, face to
be fully covered with high intensity encapsulated type heat activated retro-reflective
sheeting conforming to type-IV of ASTM-D4956-01 in yellow & black or other colour
combination including subject matter, message, symbols, borders etc. as approved
by Engineer In-charge or as per IRPWM guidelines, pasted on substrate by an
adhesive backing which shall be activated by applying heat and pressure conforming
to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium
alloy rivets @ 20 cm c/c to back-support frame of M.S. angle iron of size 25mm x
25mm x 3mm alongwith theft resistant measures, mounted and fixed with 2 nos. M.S.
angles of size 35mm x 35mm x 5mm to a vertical post made up of M.S. Tee section
ISMT 50mm x 50mm x 6mm, back side of board shall be with non-peelable weather-
proof paint, consisting of one coat of zinc chromate primer and two coats of epoxy
paint. Vertical post shall have black & white anti-corrosive paint or powder coating
complete, as directed.
203021 Caution Indicator Board

So Area of board is = 0.56sqm
Material:
2062
Man Power:
4,458.88
5,085.35
5,848.15
Rate per board Each 5,906.63

Code (Rs.)

Code (Rs.)
203022 Speed Indicator Board
Detail of cost for one board of equilateral triangular shape having each side of
1000mm with support length of 3650mm. So Area of board is = 0.433sqm
Material:
Man Power:
3,843.20
4,383.17
5,040.65
203023 Stop Indicator Board

So Area of board is = 0.56sqm
Material:
2062
Man Power:
4,458.88
5,085.35
5,848.15
203024 Termination Indicator Board

Detail of cost for one board of Circular shape having diameter of 1000mm with
support length of 3950mm. So Area of board is = 0.79sqm + wastage 25% for
circular shape = 1.0 Sqm
Material:
Aluminum Sheet / Strips of various sizes & thickness Kg 0245 200.00 6.23 1,246.00

Code (Rs.)
2062
Man Power:
5,598.55
6,385.15
7,342.92
203030 Manufacturing and supplying Trolley Refuge Indicator Boards / Level Crossing No.
Boards, made of MS sheet of 2mm thick of size 240mm dia. and 50mm x 50mm x
6mm angle, welded to MS sheet, duly painting with 2 coats of ready mixed yellow
enamel paint over one coat of red oxide with all lead & lift as per specification and as
directed by Engineer in-charge

MS Angles =10x(0.05+0.05)x0.003=0.003x7860=23.58 kgs
3700x0.23=851.00
Boards=10x3.14x0.24x0.24x0.002=0.0036x7860=28.43 kgs
Total 23.58+28.43=52.01 Kgs
Material:
H3 Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0427 20.00 4.00 80.00
2062
Man Power:
T&P Lumpsum 9901 1.00 50.00 50.00
7,982.00
9,103.47
10,468.99
Cost for 10 no. 10,573.68
Rate per unit Each 1,057.37
203040 Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to
be provided at various locations on formation, made out of MS sheet 2mm thick of
size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle
welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm
at bottom end with all lead & lift as per specification and including painting of details
with enamel paint, as directed by Engineer in-charge (Earthwork & concreting will be
paid separately)

Code (Rs.)
Details of cost for 20 nos.For 1Board required MS sheets size (450mm x 300mm &
2mm thick) So For 20 board's 20 x (0.45m x 0.30m x 0.002m) = 20 x 0.00027=
0.0054 cum, Density of MS steel is 7860 Kg/Cum, Hence Weight of MS Sheet is =
0.0054 x 7860 = 42.44 Kg, For 20 Board's required M.S.Angle of size(25 x 25 x 3mm)
= 20 {(2 x 0.45m) + (2 x 0.30m)} = 30 metre hence Volume = 30 x (0.025m + 0.025m)
x 0.003m = 30 x 0.00015 = 0.0045 Cum, Hence Weight of MS Angles = 0.0045 x
7860 = 35.37 Kg, For Post of 20 Board's @ 1.0metre long post required 20 metre
M.S.Angle of size(50 x 50 x 3mm) Volume = 20 x (0.05 + 0.05) x 0.003 = 0.006 Cum,
Hence Weight of MS Angles = 0.006 x 7860 = 47.16 Kg, Total weight of MS
Steel/Angles = 42.44+ 35.37+47.16 = 124.97 Kg + 10% wastage = 137.47Kg or 1.37
quintal so Considering Approximate weight of MS plates/Sheets/Angle 1.4 Quintal for
20 nos indicators/boards.
Material:
H3 Electrodes as per RDSO's Spec. no. IRS M:28-2011 Nos. 0427 20.00 8.00 160.00
Holding down HTS bolts with plates, nuts etc. Quintal 0235 7500 4.00 30,000.00
2062
Man Power:
T&P Lumpsum 9901 1.00 50.00 50.00
44,883.00
51,189.06
58,867.42
Cost for 20 nos. 59,456.09
204000 4. Small Track Machines :

204010 Manufacture and supply of Drill Twist, made of High Speed Steel (HSS) of various
sizes of Addision / I.T. make or equivalent, as directed by the Engineer in-charge.
204011 7.2 mm dia.

Detail cost for each.
Material:
Drill twist made of high speed of size 7.2 mm dia of Addison / I.T. make Each 0465 271.00 1.00 271.00
Misc.:
271.00
309.08
355.44
Rate per unit Each 358.99
204012 16 mm dia.
Material:
Drill twist made of high speed of size 16 mm dia of Addison / I.T. make Each 0464 1631.50 1.00 1,631.50
1,631.50
1,860.73

Code (Rs.)
2,139.83
204013 18 mm dia.
Material:
1,866.40
2,128.63
2,447.92
204014 26.5 mm dia.

Material:
2,852.30
3,253.05
3,741.01
204015 28.75 mm dia.

Material:
Drill twist made of high speed steel for size 28.75 mm dia of Addison / I T make Each 0468 3242.40 1.00 3,242.40
3,242.40
3,697.96
4,252.65
204016 31.75 mm dia.

Material:
Drill twist made of high speed steel for size 31.75 mm dia of Addison / I T make Each 0469 4335.90 1.00 4,335.90
Misc.:
4,335.90
4,945.09
5,686.86
205000 5. Welding Equipments :

205010 Manufacture & supply of rail file approximate size 15" long for filing AT welds from
Railway approved firm
Detail cost for 1 no.
Material:
Rail file 15" long for filing AT weld Each 0421 450.00 1.00 450.00
450.00

Code (Rs.)
513.23
590.21
205020 Manufacture & supply of Welding Equipments, as directed by Engineer in-charge.
205021 Welding Cable Copper (50mm2 )

Detail cost for 1 Metre.
Material:
Welding cable copper 50 mm2 Metre 0332 110.00 1.00 110.00
Misc.:
110.00
125.46
144.27
205022 Pressure Regulator for Oxygen Multi-stage cylinder

Material:
Pressure Regulator for Oxygen/Acetylene cylinder Each 0342 1450.00 1.00 1,450.00
1,450.00
1,653.73
1,901.78
205023 Pressure Regulator for Acetylene gas cylinder

Material:
Pressure Regulator for Oxygen/Acetylene cylinder Each 0342 1450.00 1.00 1,450.00
1,450.00
1,653.73
1,901.78
205024 500amp Arc Welding Electrode Holder

Material:
500 Amp Arc welding Electrode holder Each 0333 85.00 1.00 85.00
85.00
96.94
111.48
205025 Gas Cutting Torch Blow Pipe


Code (Rs.)
Material:
Welding & cutting torch Each 0334 950.00 1.00 950.00
Misc.:
950.00
1,083.48
1,246.00
Cost for each Each 1,258.46
205026 Hand Gloves Leather (Left Hand & Right Hand)

Material:
Hand gloves leather set 0335 60.00 1.00 60.00
60.00
68.43
78.69
205027 Hose Rubber for Oxygen 6mm dia.

Detail cost for 1 m
Material:
Welding Hose rubber for Oxygen/D.A. 6mm dia Metre 0336 28.00 1.00 28.00
28.00
31.93
36.72
205028 Hose Rubber for Dissolved Acetylene (D.A.) 6mm dia.

Detail cost for 1 m
Material:
Welding Hose rubber for Oxygen/D.A. 6mm dia Metre 0336 28.00 1.00 28.00
28.00
31.93
36.72
205029 Welding Screen (approximate size 4" x 3")

Material:
Welding screen Each 0337 150.00 1.00 150.00
150.00
171.08
196.74
205030 Manufacture & supply of wire brush 25mm long, as directed by Engineer in-charge

Code (Rs.)
Material:
15.00
17.11
19.67
205040 Supply of Used Lubricating Oil of approved quality

Detail cost for 1 litre
Material:
Misc.:
15.00
17.11
19.67
Rate per litre Litre 19.87
Draft IR Unified Stadard Analysis of Rates - 2021 Chapter - 21: Miscellaneous Items
CHAPTER - 21 : Miscellaneous Items

Item no. Description Unit Rate Rate (Rs) Quantity Amount (Rs.)
Code
211000 1. Miscellaneous Items
211010 Painting and fixing MS Indicator Boards of curves, SEJs, Points & Crossings,
Gang/section jurisdiction and similar as per standard design including excavation,
refilling, concreting in foundation and painting two coats with enamel and luminous
paints as directed by Engineer in-charge.
Note: Excavation, concrete work and lettering shall be paid separately.
211011 Boards with single post

Deatil of cost for 20 Boards
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,382.00
3,415.82
3,895.74
4,480.10
Rate per Board Each 226.25
211012 Boards with two posts

Deatil of cost for 20 Boards
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 12.00 12.00
3,965.00
4,004.65
4,567.30
5,252.40
211020 Erection or removal of temporary Engineering Indicator Board or any other board at
specified locations without causing infringement to track etc. complete and as
directed.
Code
211021 For erection
Details of cost for 10 boards
Labour:
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,607.50
1,623.58
1,851.69
2,129.44
Cost for 10 boards 2,150.73
211022 For removal

Details of cost for 10 boards
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
1,303.00
1,316.03
1,500.93
1,726.07
Cost for 10 boards 1,743.33
211030 Fabricating of check rails of 52Kg and 90R sections for providing to curves by
cutting web of rail horizontally by gas, grinding for smoothening the cut edge and
drilling of parabolic shaped holes to the web of check rails as per drawing and
specification and as per directions of engineer in-charge with all contractor’s labour,
tools and materials complete.
Note:
1. Rails shall be supplied by Railways
2.The both ends of head of check rails are to bent/cut as per drawing.
3. The released rail scrap shall be stacked neatly with in a lead of 500m.
4.Drilling of holes shall be paid under relavant item.
Details of cost for 100 R mts

Material:
Labour:
(ii) For cutting rail web horizontally
Mate (Skilled) Day 0002 609.00 1.00 609.00
(iii) For Stacking the releases.
Misc.:
12,412.00
Code
12,536.12
14,297.44
16,442.06
Cost for 100 RM 16,606.48
211040 Dismantling Check Rail on curves on track of all rail sections, duly removing fish
plates and bolts including removing chairs from sleepers, leading and stacking
released materials away from track clear of infringements, complete and as directed.
Details of cost for 96 Running Metres

Material:
Labour:
(i) Removing fish plates,check rail blocks/brackets plate screws
(ii) Removing, leading & stacking check rail and all fitting
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T & P (Crow bar, Rail tongue, Hammer, Spanner, Box spanner etc.) Lumpsum 9901 1.00 50.00 50.00
3,840.00
3,878.40
4,423.32
5,086.81
211050 Fixing of check rails on curves on track of all rail sections as per drawing and to
correct alignment and level with Railways fastenings including leading of rails and
fittings,crossing of tracks, greasing of plate screws with approved grease etc., as per
drawing and directions of Engineer incharge with all contractors labour, tools, plants,
machinery, consumables etc., complete.
Note: Required P.Way fittings will be supplied at SSE/P.Way stores.

Material:
Cotton Jute Kg 0494 40.00 0.50 20.00
Labour:
For leading of rails,fittings ,greasing and fixing check rail with all fittings etc.
Mate (Skilled) Day 0002 609.00 0.50 304.50
Code
Misc.:
T & P (Crow bars,Rail tongs,spanners etc ) Lumpsum 9901 1.00 30.00 30.00
4,528.50
4,573.79
5,216.40
5,998.86
Cost for 96 RM 6,058.85
211060 Supply and fixing in position pre-cast cement concrete Fouling Mark as per approved
drawing at station yard, duly painting letters of Fouling Mark, complete in all respects
with all labour, materials including cement, tools and plants etc.
(A) For casting

Detail cost for 1 cum
Material:
Labour:
Misc.:
Misc. T&P Lumpsum 9901 1.00 10.00 10.00
5,513.75
5,568.89
6,351.32
7,304.01
Rate per cum cum 7,377.05
211070 Providing and erecting water proof Gypsy Tent of size 3m x 3m for a specific period of
time and removal of the same after completion of work or as directed by Engineer in-
charge.
Detail cost for per day

Labour:
Misc.:
T & P (Transportation) Lumpsum 9901 1.00 50.00 50.00
Hire charges of 3.0 m x 3.0 m waterproof Tent Day 0163 200.00 1.00 200.00
681.00
687.81
784.45
902.11
Rate per day Day 911.14
Code
211080 Provision of furniture temporarily for site work in good condition at different locations
as per direction of Engineer In-charge, for a specific period of time & removing the
same after completion of work.
211081 Office Table of size 1.2m x 0.9m

Detail cost for 50 no's per day ( Considering 3 trips of tractor with trolley for
transportation )
Hire charges of Table Day 0165 50.00 50.00 2,500.00
3,100.00
3,131.00
3,570.91
4,106.54
Cost for 50 no's per day 4,147.61
Rate per unit per day Day 82.95
211092 Office Chairs with cushioned seat, back and arms

Detail cost for 100 no's per day ( Considering 3 trips of tractor with trolley for
transportation )
Labour:
Misc.:
T&P Lumpsum 9901 1.00 6.00 6.00
Hire charges of Chair Day 0164 15.00 100.00 1,500.00
2,537.00
2,562.37
2,922.38
3,360.74
Cost for 100 no's per day 3,394.35
Rate per unit per day Day 33.94
211100 Removing /Re-erecting existing Gradient Post / Kilometre Post, duly demolishing
concrete foundation, fixing the post in cement concrete foundation as per drawing
with 1:3:6 mix using 20mm hard aggregate, as directed (Cost of concrete work will be
paid under relevant item separately).
211101 For Removing

Details of cost for 6 post
Labour:
T & P (Crow bar, Chisel, Hammer, Phawra etc.) Lumpsum 9901 1.00 10.00 10.00
872.00
880.72
1,004.46
1,155.13
Cost for 6 post 1,166.68
Code
211102 For Fixing / Re-erecting
Details of cost for 6 post
Labour:
T & P (Crow bar, Chisel, Hammer, Phawra etc.) Lumpsum 9901 1.00 10.00 10.00
872.00
880.72
1,004.46
1,155.13
Cost for 6 post 1,166.68
211110 Breaking the damaged PSC sleepers including dragging, if required duly removing
inserts safely and handing over inserts to Railways at Stores or Depot of SSE/P.Way,
including disposing the broken concrete pieces, as directed by Engineer in-charge.
Released HTS wire shall be the property of Contractor.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
Deduction for cost of scrap value of HTS wire. Easch sleeper shall have about 8 kg of
HTS wire. For 100 sleepers, released quantity = 800 kg.
Steel wires released from U/S PSC Sleeper Kg 0478 15.00 800.00 -12,000.00
5,335.00
5,388.35
6,145.41
7,067.23
211120 Fixing vertically the unserviceable PSC sleepers at locations of tress-passing, railway
boundary or to make temporary store by excavating trench, fixing PSC sleeper in
trench and filling back open trench.

Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 50.00 50.00
7,555.00
7,630.55
8,702.64
10,008.04
Code
211130 Providing and fixing Trolley Refuge of size 3.0m x3.0m on cess, placing with
released unserviceable PSC sleepers and keepeing them at all four sides of refuge
and also placing as matting inside the refuge by keeping them in upside down
position with a minmum of 10 sleepers including levelling with earth, excavation, all
lead and lift, crossing of tracks,leading the sleepers with in a free lead and lift,
handling etc., with all contractor's men material complete and as directed by the
Engineer-in-charge.
Note: Earth-work will to be paid separately under relavent item.
Details of cost for 6 no's Trolley refuge { For one trolly refuge required 84 no's U/s
Labour:
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
15,180.00
15,331.80
17,485.92
20,108.81
Cost for 6 no's Trolley refuge 20,309.89
211140 Supplying and spraying in specified proportion Weedicide Chemical, capable to kill
entire weed on track / cess / embankment with all labour, material, tools & plants etc.
complete job in all respect. Scientific name of the chemical is Isopropylamine Salt of
Glyphosate, in which active ingredient is Glyphosate (41%), colour is light amber to
brownish, very low in toxicity and has favourable enviremental characteristics. It will
be ensured that no weed growth occurs upto six months period, otherwise respraying
shall be done by the contractor free of cost.
Details of cost for 8000 Sq.metre

Material:
Weedicide Chemical - Glyphosate Litre 0487 296.90 7.00 2,078.30
Labour:
Misc:
T&P Lumpsum 9901 1.00 50.00 50.00
3,421.30
3,455.51
3,941.01
4,532.16
Cost for 8000 Sq.metre Sqm 4,577.49
211150 Supplying & applying single liquid solution in 250ml pack, having break loose torque
of 400Nm to 540Nm, as per ISO:10123 norms with shear strength of liquid solutions
as 25 to 35 N/mm2, viscosity 1500 to 3000 (Centipoise) & specific gravity of 1.1 ±
0.05. for tightening of nuts & bolts at important locations, such as Bridges, SEJs,
Turnouts, Fish Plates, Steel Channel Sleepers etc. Work includes opening of bolts,
cleaning of bolts with suitable cleaner and tightening of bolts after applying liquid
solution as directed by Engineer in-charge.
Code
211151 Bolts dia. 20mm to 25mm
Details of cost for 100 nos Nut & Bolts
Material:
Liquid solution in 250ml pack, having break loose torque of 400Nm to 540Nm, as per Each 0491 2500.00 0.30 750.00
Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
T&P Lumpsum 9901 1.00 10.00 10.00
1,878.25
1,897.03
2,163.57
2,488.10

Material:
Liquid solution in 250ml pack, having break loose torque of 400Nm to 540Nm, as per Each 0491 2500.00 0.40 1,000.00
ISO:10123 norms with shear strength of liquid solutions as 25 to 35 N/mm2, viscosity
1500 to 3000 (Centipoise) & specific gravity of 1.1 ± 0.05. for tightening of all types of
track nuts & bolts to prevent loosening during vibrations

Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
T&P Lumpsum 9901 1.00 10.00 10.00
2,142.25
2,163.67
2,467.67
2,837.82

Material:
Liquid solution in 250ml pack, having break loose torque of 400Nm to 540Nm, as per Each 0491 2500.00 0.60 1,500.00
ISO:10123 norms with shear strength of liquid solutions as 25 to 35 N/mm2, viscosity
1500 to 3000 (Centipoise) & specific gravity of 1.1 ± 0.05. for tightening of all types of
track nuts & bolts to prevent loosening during vibrations

Labour:
Mate (Skilled) Day 0002 609.00 0.25 152.25
T&P Lumpsum 9901 1.00 10.00 10.00
Code
2,656.25
2,682.81
3,059.75
3,518.71
211160 Supplying & applying of Poly Chloroprene rubber-based Solvent (toulene free, i.e. not
harmful to human body) to prevent working out of rubber pads, having density
0.85±0.01 gm/cm3, viscosity of solvent as 1500 to 1900 (centipoise) at 30 degree
centigrade & shear strength 8 to 12 Kg/Sq.In. for bonding rubber pads / GR Sole
Plates on PSC sleepers complete job, as directed by Engineer in-charge.
211161 PSC Line sleepers

Detail of cost for 200 GR soles / Rubber pads
Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
3,666.00
3,702.66
4,222.88
4,856.32
Cost for 200 nos rubber pads 4,904.88
Rate per Rubber Pad Each 24.52
211162 1 in 8½ Turnout Set

Detail of cost for 1 set ( 216 Rubber Pads in each set )
Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
3,966.00
4,005.66
4,568.46
5,253.72
Cost for 1 Set 5,306.26
Code
211163 1 in 12 Turnout Set
Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
5,897.00
5,955.97
6,792.78
7,811.70
211164 1 in 8½ Switch Assembly

Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
2,966.00
2,995.66
3,416.55
3,929.03

Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
2,566.00
2,591.66
2,955.79
3,399.16
Code
211166 1 in 8½ Crossing Assembly
Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
2,266.00
2,288.66
2,610.22
3,001.75
Cost for Each Set Set 757.94
211167 1 in 12 Crossing Assembly

Material:
pads
Labour:
T&P Lumpsum 9901 1.00 10.00 10.00
2,466.00
2,490.66
2,840.60
3,266.69
211170 Galvanisation of Railway's Chequred Plates, Channels, Plates, Angles, I-Section,

and stretcher bars by hot dip process with Zinc Coating and mass of Zinc coating
shall not be less than 705 g/sqm and galvanisation thickness shall not be less than
100 microns including necessary surface preparation as per Clause-4 of IS:2629-
1985. Galvanisation shall be done as per IS:2629-1985 and IS:4759-1996 with Zinc
conforming to IS:209-1992, duly taking all the measures for safeguarding against
embrittlement of hot-dip galvanised iron and steel products as per IS:6158-1984 with
all contractor's labour, material, tools, plant, all lead, lift and crossing of tracks etc.
complete and as directed by the Engineer in-charge.

Material:
Labour:
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
86,882.00
Code
87,750.82
100,079.81
115,091.78
Cost for 5 MT 116,242.70
211180 Galvanisation of Railway's Chequred Plates, Channels, Plates, Angles, I-Section,

stretcher bars, M.S.Liners, ERCs and Plate screws by hot dip process with Zinc
Coating and mass of Zinc coating shall not be less than 705 g/sqm and galvanisation
thickness shall not be less than 100 microns including necessary surface preparation
as per Clause-4 of IS:2629-1985. Galvanisation shall be done as per IS:2629-1985
and IS:4759-1996 with Zinc conforming to IS:209-1992, duly taking all the measures
for safeguarding against embrittlement of hot-dip galvanised iron and steel products
as per IS:6158-1984 with all contractor's labour, material, tools, plant, all lead, lift and
crossing of tracks etc. complete and as directed by the Engineer in-charge.
Considering 20% of extra on 211170 for additional items

Rate as per item no. 211170 211170 23,248.54
Add 20% overabove 4,649.71
211200 Hiring of JCB upto 1 cum bucket capacity or other similar machinery for levelling and
dressing ground/dismantling structures, Removal of jungle, clearing of earth, lowering
high cess etc., along side the track between up and down lines obstructing drainages
of rain water, clearing of bushes obstructing visibility at curves and Level Crossings
with all lead and lift etc. complete and as directed by the Engineer-in-charge. All
labour, tools and plants consumables stores including supply of earth mover with
crew to be provided by the contractor at his own cost. The contractor shall arrange
road permit for vehicle for all the States of operation, as per instructions of engineer in-
charge and vehicle shall not be more than three years old. Payment shall be made for
actual working hours at site.
Cost per one hour

Misc.:
Hire Charges of JCB of 0.92 cum bucket Capacity Hour 0058 800.00 1.00 800.00
810.00
818.10
933.04
1,073.00
Rate per hour Hour 1,083.73
211210 Arranging labour as and when required by the Engineer incharge, for various works
under SSE/P.Way, with contractor's T&P, equipments, hand signal flags, etc. as per
specifications, special conditions and detailed scope of work as furnished in the
tender and as directed by the Engineer incharge.
Note: Item shall be operated with prior approval of concerned Sr. DEN / DEN
incharge.
Labour:
Misc.:
441.00
Code
445.41
507.99
584.19
Rate per labour per day Day 590.03
211220 Supplying and filling 50 kg size empty cement polythene bags with Rly.
Ballast/moorum/earth/Sand/quarry dust etc. placing the filled bags on the high banks
/bridge approaches/nominated place etc. dumping and spreading at the nominated
locations to profile under block period with all contractor's labour, tools, plants. ,
loading, unloading, filling, spreading including all lead/lift etc. complete and as
directed by the Engineer in charge at site including crossing of track where
necessary.
Details of Cost for 400 bags
Material
Empty cement bag polythene 50 Kgs capacity Each 0495 5.00 400.00 2,000.00
Labour:
Filling and carrying then to high banks.bridge approaches/nominated place including
Mate (Skilled) Day 0002 609.00 0.50 304.50
Misc.:
T&P Lumpsum 9901 1.00 10.00 10.00
4,038.50
4,078.89
4,651.97
5,349.76
Cost of 400 bags 5,403.26
Rate per bag Each 13.51
211230 Filling and stacking of sand bags layer by layer filled with Railway Sand/railway quarry
dust in Contractor's empty polythene cement bags of 50 kg bags with all contractors
labour, tools, plants, lead, lift etc., including stiching the same with machine using
polythene thread complete as directed by Engineer-incharge at site.

Material
Labour:
For Filling and stacking sand bags
Misc.:
Sundries (stitching machine) Lumpsum 9901 1.00 20.00 20.00
5,606.00
5,662.06
6,457.58
7,426.22
Cost of 600 bags 7,500.48
211240 Loading of sand/quarry dust filled bags from Railway stacks in to Railway Wagons
with all contractor's tools & plants, machinary, labour, lead and lift, crossing of track
wherever necessary etc., complete as directed by the Engineer Incharge.
Material:
Code
Labour:
For loading of bags in to vehicles
Mate (Skilled) Day 0002 609.00 0.50 304.50
6,800.50
6,868.51
7,833.53
9,008.56
Cost of 780 Bags 9,098.65
211250 Manufacturing and fixing buffer stop with Railway supplied rails, cutting, including
bending of rails as per plan ,with all contractor’s labour,materials, tools, plants etc.
and all lead and lift including crossing of track where necessary and as directed by
Engineer in charge at site.
Note: Excavation, fixing rails in cement concrete, drilling of holes will be paid
seperately.
Details of cost for one buffer stop

Materials
Man Power
Mate (Skilled) Day 0002 609.00 1.00 609.00
Misc.:
Sundries ( Spanners,,gas torch) Lumpsum 9901 1.00 20.00 20.00
10,348.00
10,451.48
11,919.91
13,707.90
Rate per buffer stop Each 13,844.98
211260 Manufacture and supply of Precast Kilometer Posts of size 1.15x0.50m and 75mm
thick in RCC 1:2:4 mix, engraving letters and leading to work spot, fixing in position
with CC 1:3:6 concrete duly making pits of size as required, painting the post, writing
the letters on both sides of the post with 2 coats of enamel paint of approved quality
to the Railways drawings/IRPWM with contractor's materials, cement, steel, labour,
tools, plant, with all lead and lifts etc., complete as per specifications and as directed
Note: Excavation, Concrete and steel work will be paid under relavent items.
Details of Cost of 30 boards

Material:
Labour:
Misc.:
Code
T&P ( crow bars,shovels etc) Lumpsum 9901 1.00 20.00 20.00
8,317.00
8,400.17
9,580.39
11,017.45
Cost of 30 Boards 11,127.63
211270 Manufacture and supply of Precast gradient Posts of size 1.65 x 0.60 m and 75mm
thick in RCC 1:2:4 mix, engraving letters and leading to work spot, fixing in position
with CC 1:3:6 concrete duly making pits of size as required, painting the post, writing
the letters on both sides of posts in 2 coats with enamel paint of approved quality to
the Railways drawings/IRPWM with contractor's materials, cement, steel, labour,
tools, plant, with all lead and lifts etc., complete as per specifications and as directed
Note: Excavation,Concrete and steel work will be paid under relavent items.

Materials
Man power
Misc.:
13,284.00
13,416.84
15,301.91
17,597.19
211280 Manufacture and supply of Precast Hectometer/TP Repeator posts of size

0.90Mx0.30 mx0.30Mx0.30M Triangular size in RCC 1:2:4 mix,engraving
letters,leading to work spot, and fixing in position with CC 1:3:6 concrete,duly making
pits of size as required,painting the post with two coats,letters on the both sides of
posts with enamel paint of approved quality as per IRPWM/Railways drawings
complete with contractor's materials, cement, steel, labour, tools, plant, with all lead
and lifts etc., complete as per specifications and as directed by the Engineer-in-
charge.
Note: Excavation, Concrete and steel work will be paid under relavent items.

Materials:
Man power
Misc.:
Code
12,774.00
12,901.74
14,714.43
16,921.60
Analysis of Rates for transportation P. Way Material other than PSC sleeper, Rails, Switches, Glued Joints, & Crossings
Rate Linked
Name Unit Rate Code to Basic
Sheet
Hire Day 0059 2000.00
Charges of
Truck - 9
Diesel Litre 0181 101.62
Beldar (Un Day 0025 431.00
Diesel kmpl 5.00
Mobile oil kmpl 140.00
Time of hour 1.00
Distance kmpl 6.00
from
Lead in Average Nos. of Nos. of km Litres of Cost of Hire Total Cost = Cost per Trip Cost per Rate per
km (L) Speed IN Trips Done in Diesel Diesel Charges of col. 6+7 = Col.10/Col.3 tonne tonne per
KMPH (S) N=8/(2L/S) one day consumed Truck km
+0.5 (2NL+6) (0084)
1 2 3 4 5 6 7 8 9 10 11
1 16.00 7.11 20.22 4.04 411.00 2,000.00 2,411.00 339.05 37.67 37.67
2 17.00 6.48 31.90 6.38 648.43 2,000.00 2,648.43 408.95 45.44 22.72
2.50 17.25 6.20 37.01 7.40 752.22 2,000.00 2,752.22 443.75 49.31 19.72
3 17.50 5.96 41.74 8.35 848.42 2,000.00 2,848.42 478.13 53.13 17.71
4 18.00 5.54 50.31 10.06 1,022.45 2,000.00 3,022.45 545.72 60.64 15.16
5 18.50 5.19 57.93 11.59 1,177.37 2,000.00 3,177.37 611.86 67.98 13.60
6 19.00 4.90 64.84 12.97 1,317.78 2,000.00 3,317.78 676.65 75.18 12.53
7 19.50 4.66 71.19 14.24 1,446.95 2,000.00 3,446.95 740.21 82.25 11.75
7.50 19.75 4.55 74.20 14.84 1,508.07 2,000.00 3,508.07 771.55 85.73 11.43
8 20.00 4.44 77.11 15.42 1,567.21 2,000.00 3,567.21 802.62 89.18 11.15
9 20.50 4.26 82.68 16.54 1,680.29 2,000.00 3,680.29 863.97 96.00 10.67
10 21.00 4.10 87.95 17.59 1,787.52 2,000.00 3,787.52 924.34 102.70 10.27
11 21.50 3.95 92.99 18.60 1,889.90 2,000.00 3,889.90 983.78 109.31 9.94
12 22.00 3.83 97.83 19.57 1,988.22 2,000.00 3,988.22 1,042.38 115.82 9.65
13 22.50 3.71 102.49 20.50 2,083.11 2,000.00 4,083.11 1,100.17 122.24 9.40
14 23.00 3.61 107.02 21.40 2,175.07 2,000.00 4,175.07 1,157.22 128.58 9.18
15 23.50 3.51 111.42 22.28 2,264.51 2,000.00 4,264.51 1,213.57 134.84 8.99
16 24.00 3.43 115.71 23.14 2,351.78 2,000.00 4,351.78 1,269.27 141.03 8.81
17 24.50 3.35 119.91 23.98 2,437.14 2,000.00 4,437.14 1,324.35 147.15 8.66
18 25.00 3.28 124.03 24.81 2,520.84 2,000.00 4,520.84 1,378.86 153.21 8.51
19 25.50 3.21 128.08 25.62 2,603.07 2,000.00 4,603.07 1,432.82 159.20 8.38
20 26.00 3.15 132.06 26.41 2,684.00 2,000.00 4,684.00 1,486.27 165.14 8.26
21 26.50 3.09 135.99 27.20 2,763.77 2,000.00 4,763.77 1,539.24 171.03 8.14
22 27.00 3.04 139.86 27.97 2,842.50 2,000.00 4,842.50 1,591.75 176.86 8.04
23 27.50 2.99 143.69 28.74 2,920.30 2,000.00 4,920.30 1,643.83 182.65 7.94
24 28.00 2.95 147.47 29.49 2,997.26 2,000.00 4,997.26 1,695.50 188.39 7.85
25 28.50 2.90 151.22 30.24 3,073.45 2,000.00 5,073.45 1,746.78 194.09 7.76
26 29.00 2.86 154.94 30.99 3,148.97 2,000.00 5,148.97 1,797.70 199.74 7.68
27 29.50 2.83 158.62 31.72 3,223.85 2,000.00 5,223.85 1,848.27 205.36 7.61
28 30.00 2.79 162.28 32.46 3,298.16 2,000.00 5,298.16 1,898.51 210.95 7.53
29 30.50 2.76 165.91 33.18 3,371.95 2,000.00 5,371.95 1,948.43 216.49 7.47
30 31.00 2.73 169.52 33.90 3,445.25 2,000.00 5,445.25 1,998.06 222.01 7.40
31 31.50 2.70 173.10 34.62 3,518.12 2,000.00 5,518.12 2,047.40 227.49 7.34
32 32.00 2.67 176.67 35.33 3,590.57 2,000.00 5,590.57 2,096.47 232.94 7.28
33 32.50 2.64 180.21 36.04 3,662.65 2,000.00 5,662.65 2,145.27 238.36 7.22
34 33.00 2.61 183.74 36.75 3,734.38 2,000.00 5,734.38 2,193.84 243.76 7.17
35 33.50 2.59 187.26 37.45 3,805.79 2,000.00 5,805.79 2,242.16 249.13 7.12
36 34.00 2.57 190.75 38.15 3,876.90 2,000.00 5,876.90 2,290.26 254.47 7.07
37 34.50 2.54 194.24 38.85 3,947.73 2,000.00 5,947.73 2,338.15 259.79 7.02
38 35.00 2.52 197.71 39.54 4,018.29 2,000.00 6,018.29 2,385.82 265.09 6.98
39 35.50 2.50 201.17 40.23 4,088.62 2,000.00 6,088.62 2,433.30 270.37 6.93
40 36.00 2.48 204.62 40.92 4,158.71 2,000.00 6,158.71 2,480.59 275.62 6.89
41 36.50 2.46 208.06 41.61 4,228.59 2,000.00 6,228.59 2,527.70 280.86 6.85
42 37.00 2.45 211.49 42.30 4,298.27 2,000.00 6,298.27 2,574.63 286.07 6.81
43 37.50 2.43 214.91 42.98 4,367.77 2,000.00 6,367.77 2,621.40 291.27 6.77
44 38.00 2.41 218.32 43.66 4,437.08 2,000.00 6,437.08 2,668.00 296.44 6.74
45 38.50 2.40 221.72 44.34 4,506.23 2,000.00 6,506.23 2,714.45 301.61 6.70
46 39.00 2.38 225.11 45.02 4,575.23 2,000.00 6,575.23 2,760.75 306.75 6.67
47 39.50 2.37 228.50 45.70 4,644.07 2,000.00 6,644.07 2,806.91 311.88 6.64
48 40.00 2.35 231.88 46.38 4,712.78 2,000.00 6,712.78 2,852.93 316.99 6.60
49 40.50 2.34 235.26 47.05 4,781.35 2,000.00 6,781.35 2,898.82 322.09 6.57
50 41.00 2.33 238.62 47.72 4,849.80 2,000.00 6,849.80 2,944.58 327.18 6.54
60 46.00 2.22 272.02 54.40 5,528.62 2,000.00 7,528.62 3,396.06 377.34 6.29
62.5 48.00 2.22 283.46 56.69 5,760.97 2,000.00 7,760.97 3,496.48 388.50 6.22
70 51.00 2.14 305.06 61.01 6,199.99 2,000.00 8,199.99 3,838.72 426.52 6.09
75 53.00 2.09 319.30 63.86 6,489.46 2,000.00 8,489.46 4,064.53 451.61 6.02
80 56.00 2.07 337.85 67.57 6,866.50 2,000.00 8,866.50 4,274.92 474.99 5.94
87.5 59.00 2.02 358.99 71.80 7,296.14 2,000.00 9,296.14 4,608.68 512.08 5.85
90 60.00 2.00 366.00 73.20 7,438.58 2,000.00 9,438.58 4,719.29 524.37 5.83
100 60.00 1.85 375.23 75.05 7,626.19 2,000.00 9,626.19 5,214.19 579.35 5.79
125 60.00 1.55 393.10 78.62 7,989.30 2,000.00 9,989.30 6,451.42 716.82 5.73
150 60.00 1.33 406.00 81.20 8,251.54 2,000.00 10,251.54 7,688.66 854.30 5.70
200 60.00 1.04 423.39 84.68 8,605.00 2,000.00 10,605.00 10,163.13 1,129.24 5.65
300 60.00 0.73 442.36 88.47 8,990.60 2,000.00 10,990.60 15,112.07 1,679.12 5.60
400 60.00 0.56 452.51 90.50 9,196.85 2,000.00 11,196.85 20,061.02 2,229.00 5.57
500 60.00 0.45 458.83 91.77 9,325.26 2,000.00 11,325.26 25,009.96 2,778.88 5.56
1000 60.00 0.23 472.02 94.40 9,593.32 2,000.00 11,593.32 49,754.68 5,528.30 5.53
5000 60.00 0.05 483.14 96.63 9819.28 2,000.00 11,819.28 247,712.41 27,523.60 5.50
Number of trip in working day of 8 hours N = 8/((2L/S)+1), Where L = Lead in Km, S = Speed in Km per hour, 1/2 hour is
ll d f l ofdimobile
Consumption / oill taken
di at 140 Km per litre.
In column 4 of 'Km done' an allowance of 6.0 Km has been made for movement of truck from parking place to duty and back
Cost of labour, hire charges of truck, diesel and mobile has been taken from the basic rate sheet. Loading is to be done Track
Analysis of Rates for transportation stone Track Ballast
Rate
Linked to
Name Unit Rate Code
Basic
Sheet
Hire and running charges of Day 0049 2500.00
Tipper 12 Cum Capacity (without
POL)
Diesel (HSD Oil) Litre 0181 101.62
Mobile Oil Litre 0186 250.00
Diesel consumption rate kmpl 6.00
Mobile oil consumption rate kmpl 140.00
Time of Loading/Unloading hour 0.50
Distance from Parking Place to kmpl 6.00
Duty & Back to Parking Place
Lead in Average Nos. of Nos. of km Litres of Cost of Litres of Cost of Hire Total Cost = Cost per Cost per Rate per
km (L) Speed IN Trips Done in Diesel Diesel Mobil oil Mobile Charges of col. 6+8+9 Trip = cum cum per km
KMPH (S) N=8/(2L/S) one day consumed consumed oil Truck Col.10/Co
+0.5 (2NL+6) @ 140 km (0084) l.3
per Litre
1 2 3 4 5 6 7 8 9 10 11
1 16.00 12.80 31.60 5.27 535.20 0.23 56.43 2,500.00 3,091.63 241.53 20.13 20.13
2 17.00 10.88 49.52 8.25 838.70 0.35 88.43 2,500.00 3,427.13 314.99 26.25 13.12
3 17.50 9.49 62.95 10.49 1,066.15 0.45 112.41 2,500.00 3,678.56 387.56 32.30 10.77
4 18.00 8.47 73.76 12.29 1,249.33 0.53 131.72 2,500.00 3,881.05 458.18 38.18 9.55
5 18.50 7.69 82.88 13.81 1,403.76 0.59 148.01 2,500.00 4,051.77 527.00 43.92 8.78
6 19.00 7.07 90.84 15.14 1,538.48 0.65 162.21 2,500.00 4,200.69 594.18 49.51 8.25
7 19.50 6.57 97.96 16.33 1,659.08 0.70 174.92 2,500.00 4,334.01 659.82 54.99 7.86
8 20.00 6.15 104.46 17.41 1,769.23 0.75 186.54 2,500.00 4,455.77 724.06 60.34 7.54
9 20.50 5.81 110.50 18.42 1,871.43 0.79 197.31 2,500.00 4,568.74 786.99 65.58 7.29
10 21.00 5.51 116.16 19.36 1,967.43 0.83 207.44 2,500.00 4,674.87 848.71 70.73 7.07
11 21.50 5.25 121.54 20.26 2,058.52 0.87 217.04 2,500.00 4,775.56 909.30 75.77 6.89
12 22.00 5.03 126.69 21.11 2,145.63 0.90 226.22 2,500.00 4,871.86 968.84 80.74 6.73
13 22.50 4.83 131.64 21.94 2,229.50 0.94 235.07 2,500.00 4,964.57 1,027.39 85.62 6.59
14 23.00 4.66 136.43 22.74 2,310.68 0.97 243.63 2,500.00 5,054.30 1,085.03 90.42 6.46
15 23.50 4.50 141.09 23.51 2,389.59 1.01 251.95 2,500.00 5,141.54 1,141.80 95.15 6.34
16 24.00 4.36 145.64 24.27 2,466.59 1.04 260.06 2,500.00 5,226.66 1,197.78 99.81 6.24
17 24.50 4.24 150.09 25.01 2,541.96 1.07 268.01 2,500.00 5,309.98 1,252.99 104.42 6.14
18 25.00 4.12 154.45 25.74 2,615.93 1.10 275.81 2,500.00 5,391.74 1,307.50 108.96 6.05
19 25.50 4.02 158.75 26.46 2,688.67 1.13 283.48 2,500.00 5,472.15 1,361.33 113.44 5.97
20 26.00 3.92 162.98 27.16 2,760.36 1.16 291.04 2,500.00 5,551.39 1,414.54 117.88 5.89
21 26.50 3.84 167.16 27.86 2,831.11 1.19 298.50 2,500.00 5,629.60 1,467.15 122.26 5.82
22 27.00 3.76 171.29 28.55 2,901.03 1.22 305.87 2,500.00 5,706.90 1,519.20 126.60 5.75
23 27.50 3.68 175.37 29.23 2,970.22 1.25 313.16 2,500.00 5,783.39 1,570.72 130.89 5.69
24 28.00 3.61 179.42 29.90 3,038.77 1.28 320.39 2,500.00 5,859.16 1,621.73 135.14 5.63
25 28.50 3.55 183.43 30.57 3,106.73 1.31 327.56 2,500.00 5,934.28 1,672.27 139.36 5.57
26 29.00 3.49 187.41 31.24 3,174.16 1.34 334.67 2,500.00 6,008.83 1,722.36 143.53 5.52
27 29.50 3.43 191.37 31.89 3,241.12 1.37 341.73 2,500.00 6,082.85 1,772.02 147.67 5.47
28 30.00 3.38 195.30 32.55 3,307.66 1.39 348.74 2,500.00 6,156.40 1,821.27 151.77 5.42
29 30.50 3.33 199.20 33.20 3,373.81 1.42 355.72 2,500.00 6,229.52 1,870.13 155.84 5.37
30 31.00 3.28 203.09 33.85 3,439.60 1.45 362.65 2,500.00 6,302.26 1,918.63 159.89 5.33
31 31.50 3.24 206.95 34.49 3,505.07 1.48 369.56 2,500.00 6,374.63 1,966.78 163.90 5.29
32 32.00 3.20 210.80 35.13 3,570.25 1.51 376.43 2,500.00 6,446.68 2,014.59 167.88 5.25
33 32.50 3.16 214.63 35.77 3,635.15 1.53 383.27 2,500.00 6,518.43 2,062.08 171.84 5.21
34 33.00 3.12 218.45 36.41 3,699.81 1.56 390.09 2,500.00 6,589.90 2,109.27 175.77 5.17
35 33.50 3.09 222.25 37.04 3,764.24 1.59 396.88 2,500.00 6,661.12 2,156.16 179.68 5.13
36 34.00 3.06 226.04 37.67 3,828.45 1.61 403.65 2,500.00 6,732.10 2,202.78 183.57 5.10
37 34.50 3.02 229.82 38.30 3,892.46 1.64 410.40 2,500.00 6,802.86 2,249.14 187.43 5.07
38 35.00 2.99 233.59 38.93 3,956.30 1.67 417.13 2,500.00 6,873.43 2,295.23 191.27 5.03
39 35.50 2.97 237.35 39.56 4,019.96 1.70 423.84 2,500.00 6,943.80 2,341.09 195.09 5.00
40 36.00 2.94 241.10 40.18 4,083.46 1.72 430.54 2,500.00 7,014.00 2,386.71 198.89 4.97
41 36.50 2.91 244.84 40.81 4,146.82 1.75 437.22 2,500.00 7,084.04 2,432.11 202.68 4.94
42 37.00 2.89 248.58 41.43 4,210.04 1.78 443.89 2,500.00 7,153.93 2,477.29 206.44 4.92
43 37.50 2.86 252.30 42.05 4,273.13 1.80 450.54 2,500.00 7,223.67 2,522.26 210.19 4.89
44 38.00 2.84 256.02 42.67 4,336.10 1.83 457.18 2,500.00 7,293.28 2,567.04 213.92 4.86
45 38.50 2.82 259.73 43.29 4,398.96 1.86 463.80 2,500.00 7,362.76 2,611.63 217.64 4.84
46 39.00 2.80 263.43 43.91 4,461.71 1.88 470.42 2,500.00 7,432.13 2,656.03 221.34 4.81
47 39.50 2.78 267.13 44.52 4,524.36 1.91 477.03 2,500.00 7,501.39 2,700.26 225.02 4.79
48 40.00 2.76 270.83 45.14 4,586.92 1.93 483.62 2,500.00 7,570.54 2,744.32 228.69 4.76
49 40.50 2.74 274.52 45.75 4,649.38 1.96 490.21 2,500.00 7,639.59 2,788.21 232.35 4.74
50 41.00 2.72 278.20 46.37 4,711.77 1.99 496.78 2,500.00 7,708.55 2,831.95 236.00 4.72
60 46.00 2.57 314.81 52.47 5,331.85 2.25 562.16 2,500.00 8,394.02 3,261.80 271.82 4.53
70 51.00 2.47 351.14 58.52 5,947.07 2.51 627.03 2,500.00 9,074.10 3,680.79 306.73 4.38
75 53.00 2.40 366.34 61.06 6,204.58 2.62 654.18 2,500.00 9,358.76 3,895.80 324.65 4.33
80 56.00 2.38 387.28 64.55 6,559.17 2.77 691.57 2,500.00 9,750.74 4,091.83 340.99 4.26
90 60.00 2.29 417.43 69.57 7,069.85 2.98 745.41 2,500.00 10,315.26 4,512.92 376.08 4.18
100 60.00 2.09 423.39 70.57 7,170.84 3.02 756.06 2,500.00 10,426.89 4,996.22 416.35 4.16
125 60.00 1.71 434.57 72.43 7,360.19 3.10 776.02 2,500.00 10,636.21 6,204.46 517.04 4.14
175 60.00 1.26 448.11 74.68 7,589.41 3.20 800.19 2,500.00 10,889.60 8,620.93 718.41 4.11
225 60.00 1.00 456.00 76.00 7,723.12 3.26 814.29 2,500.00 11,037.41 11,037.41 919.78 4.09
500 60.00 0.47 472.02 78.67 7,994.44 3.37 842.89 2,500.00 11,337.33 24,328.01 2,027.33 4.05
1000 60.00 0.24 478.91 79.82 8,111.08 3.42 855.19 2,500.00 11,466.27 48,492.76 4,041.06 4.04
Number of trip in working day of 8 hours N = 8/((2L/S)+1), Where L = Lead in Km, S = Speed in Km per hour, 1/2 hour is allowed for loading /
l di
Consumption of mobile oil taken at 140 Km per litre.
Cost of labour, hire charges of truck, diesel and mobile has been taken from the basic rate sheet. Loading is to be done Track Ballast Manufacturer.
Analysis of Rates for transportation Precast Girders/Slab
By Mechanical Transport including unloading and stacking
Name Unit Rate Code Rate Linked
to Basic
Sheet
Hire Charges of 20T truck with long Trailors (without Day 0103 5000.00
POL)
Hiring charges of Crane 50 MT capacity Day 0094 20000.00
Coolie (Un skilled) Day 0026 431.00

Diesel (HSD) Oil Litre 0181 101.62
Mobile Oil Litre 0186 250.00
Diesel consumption rate kmpl 2.65
Mobile oil consumption rate kmpl 140.00
Time of Loading/Unloading hour 0.50
Distance to and fro between worksite and….. kmpl 6.00
Lead in Average Nos. of Nos. of km Litres of Cost of Litres of Cost of Cost of 2 Hire Total Cost = Cost per Cost of Total Cost Cost per Rate Rate per ton
km (L) Speed IN Trips Done in Diesel Diesel Mobil oil Mobile Beldar at site Charges of col. 6+8+9+10 Trip = Crane per trip i.e. tone including per km
KMPH (S) N=8/(2L/S) one day consumed consumed oil for unloading Truck Col.11/Col. Charges cost for 20
+0.5
GST, CPOH
(2NL+6) @ 140 km with crane (0084) 3 except for
t & Cess
per Litre except hire Crane Loading &
charges of charges unloading
crane per trip
considerin
g 1/4 hrs
of crane
time each
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 16.00 12.80 31.60 11.92 1,211.77 0.23 56.43 862.00 5,000.00 7,130.20 557.05 1,250.00 1,807.05 90.35 119.69 119.69
2 17.00 10.88 49.52 18.69 1,898.95 0.35 88.43 862.00 5,000.00 7,849.38 721.45 1,250.00 1,971.45 98.57 130.58 65.29
3 17.50 9.49 62.95 23.75 2,413.92 0.45 112.41 862.00 5,000.00 8,388.33 883.77 1,250.00 2,133.77 106.69 141.33 47.11
4 18.00 8.47 73.76 27.84 2,828.67 0.53 131.72 862.00 5,000.00 8,822.39 1,041.53 1,250.00 2,291.53 114.58 151.78 37.94
5 18.50 7.69 82.88 31.28 3,178.33 0.59 148.01 862.00 5,000.00 9,188.34 1,195.10 1,250.00 2,445.10 122.26 161.95 32.39
6 19.00 7.07 90.84 34.28 3,483.35 0.65 162.21 862.00 5,000.00 9,507.56 1,344.82 1,250.00 2,594.82 129.74 171.87 28.64
7 19.50 6.57 97.96 36.97 3,756.41 0.70 174.92 862.00 5,000.00 9,793.33 1,490.97 1,250.00 2,740.97 137.05 181.55 25.94
8 20.00 6.15 104.46 39.42 4,005.80 0.75 186.54 862.00 5,000.00 10,054.34 1,633.83 1,250.00 2,883.83 144.19 191.01 23.88
9 20.50 5.81 110.50 41.70 4,237.19 0.79 197.31 862.00 5,000.00 10,296.51 1,773.64 1,250.00 3,023.64 151.18 200.27 22.25
10 21.00 5.51 116.16 43.84 4,454.56 0.83 207.44 862.00 5,000.00 10,523.99 1,910.61 1,250.00 3,160.61 158.03 209.34 20.93
11 21.50 5.25 121.54 45.86 4,660.79 0.87 217.04 862.00 5,000.00 10,739.83 2,044.94 1,250.00 3,294.94 164.75 218.24 19.84
12 22.00 5.03 126.69 47.81 4,858.04 0.90 226.22 862.00 5,000.00 10,946.26 2,176.81 1,250.00 3,426.81 171.34 226.97 18.91
13 22.50 4.83 131.64 49.67 5,047.93 0.94 235.07 862.00 5,000.00 11,145.00 2,306.39 1,250.00 3,556.39 177.82 235.56 18.12
14 23.00 4.66 136.43 51.48 5,231.72 0.97 243.63 862.00 5,000.00 11,337.34 2,433.83 1,250.00 3,683.83 184.19 244.00 17.43
15 23.50 4.50 141.09 53.24 5,410.40 1.01 251.95 862.00 5,000.00 11,524.34 2,559.26 1,250.00 3,809.26 190.46 252.30 16.82
16 24.00 4.36 145.64 54.96 5,584.74 1.04 260.06 862.00 5,000.00 11,706.81 2,682.81 1,250.00 3,932.81 196.64 260.49 16.28
17 24.50 4.24 150.09 56.64 5,755.39 1.07 268.01 862.00 5,000.00 11,885.40 2,804.59 1,250.00 4,054.59 202.73 268.55 15.80
18 25.00 4.12 154.45 58.28 5,922.86 1.10 275.81 862.00 5,000.00 12,060.67 2,924.71 1,250.00 4,174.71 208.74 276.51 15.36
19 25.50 4.02 158.75 59.91 6,087.57 1.13 283.48 862.00 5,000.00 12,233.05 3,043.27 1,250.00 4,293.27 214.66 284.36 14.97
20 26.00 3.92 162.98 61.50 6,249.87 1.16 291.04 862.00 5,000.00 12,402.90 3,160.36 1,250.00 4,410.36 220.52 292.12 14.61
21 26.50 3.84 167.16 63.08 6,410.05 1.19 298.50 862.00 5,000.00 12,570.55 3,276.05 1,250.00 4,526.05 226.30 299.78 14.28
22 27.00 3.76 171.29 64.64 6,568.37 1.22 305.87 862.00 5,000.00 12,736.24 3,390.43 1,250.00 4,640.43 232.02 307.36 13.97
23 27.50 3.68 175.37 66.18 6,725.03 1.25 313.16 862.00 5,000.00 12,900.20 3,503.58 1,250.00 4,753.58 237.68 314.85 13.69
24 28.00 3.61 179.42 67.71 6,880.22 1.28 320.39 862.00 5,000.00 13,062.62 3,615.55 1,250.00 4,865.55 243.28 322.27 13.43
25 28.50 3.55 183.43 69.22 7,034.09 1.31 327.56 862.00 5,000.00 13,223.65 3,726.40 1,250.00 4,976.40 248.82 329.61 13.18
26 29.00 3.49 187.41 70.72 7,186.78 1.34 334.67 862.00 5,000.00 13,383.45 3,836.20 1,250.00 5,086.20 254.31 336.88 12.96
27 29.50 3.43 191.37 72.21 7,338.39 1.37 341.73 862.00 5,000.00 13,542.12 3,945.00 1,250.00 5,195.00 259.75 344.09 12.74
28 30.00 3.38 195.30 73.70 7,489.04 1.39 348.74 862.00 5,000.00 13,699.78 4,052.85 1,250.00 5,302.85 265.14 351.23 12.54
29 30.50 3.33 199.20 75.17 7,638.81 1.42 355.72 862.00 5,000.00 13,856.53 4,159.80 1,250.00 5,409.80 270.49 358.32 12.36
30 31.00 3.28 203.09 76.64 7,787.78 1.45 362.65 862.00 5,000.00 14,012.43 4,265.88 1,250.00 5,515.88 275.79 365.34 12.18
31 31.50 3.24 206.95 78.10 7,936.01 1.48 369.56 862.00 5,000.00 14,167.57 4,371.15 1,250.00 5,621.15 281.06 372.31 12.01
32 32.00 3.20 210.80 79.55 8,083.58 1.51 376.43 862.00 5,000.00 14,322.01 4,475.63 1,250.00 5,725.63 286.28 379.23 11.85
33 32.50 3.16 214.63 80.99 8,230.54 1.53 383.27 862.00 5,000.00 14,475.81 4,579.37 1,250.00 5,829.37 291.47 386.11 11.70
34 33.00 3.12 218.45 82.43 8,376.93 1.56 390.09 862.00 5,000.00 14,629.02 4,682.39 1,250.00 5,932.39 296.62 392.93 11.56
35 33.50 3.09 222.25 83.87 8,522.80 1.59 396.88 862.00 5,000.00 14,781.68 4,784.74 1,250.00 6,034.74 301.74 399.71 11.42
36 34.00 3.06 226.04 85.30 8,668.18 1.61 403.65 862.00 5,000.00 14,933.84 4,886.44 1,250.00 6,136.44 306.82 406.44 11.29
37 34.50 3.02 229.82 86.73 8,813.13 1.64 410.40 862.00 5,000.00 15,085.53 4,987.52 1,250.00 6,237.52 311.88 413.14 11.17
38 35.00 2.99 233.59 88.15 8,957.65 1.67 417.13 862.00 5,000.00 15,236.78 5,088.00 1,250.00 6,338.00 316.90 419.79 11.05
39 35.50 2.97 237.35 89.57 9,101.80 1.70 423.84 862.00 5,000.00 15,387.64 5,187.91 1,250.00 6,437.91 321.90 426.41 10.93
40 36.00 2.94 241.10 90.98 9,245.58 1.72 430.54 862.00 5,000.00 15,538.12 5,287.28 1,250.00 6,537.28 326.86 432.99 10.82
41 36.50 2.91 244.84 92.39 9,389.03 1.75 437.22 862.00 5,000.00 15,688.25 5,386.12 1,250.00 6,636.12 331.81 439.54 10.72
42 37.00 2.89 248.58 93.80 9,532.17 1.78 443.89 862.00 5,000.00 15,838.06 5,484.46 1,250.00 6,734.46 336.72 446.05 10.62
43 37.50 2.86 252.30 95.21 9,675.02 1.80 450.54 862.00 5,000.00 15,987.56 5,582.32 1,250.00 6,832.32 341.62 452.54 10.52
44 38.00 2.84 256.02 96.61 9,817.59 1.83 457.18 862.00 5,000.00 16,136.77 5,679.72 1,250.00 6,929.72 346.49 458.99 10.43
45 38.50 2.82 259.73 98.01 9,959.91 1.86 463.80 862.00 5,000.00 16,285.71 5,776.67 1,250.00 7,026.67 351.33 465.41 10.34
46 39.00 2.80 263.43 99.41 10,101.99 1.88 470.42 862.00 5,000.00 16,434.41 5,873.19 1,250.00 7,123.19 356.16 471.80 10.26
47 39.50 2.78 267.13 100.81 10,243.84 1.91 477.03 862.00 5,000.00 16,582.86 5,969.31 1,250.00 7,219.31 360.97 478.17 10.17
48 40.00 2.76 270.83 102.20 10,385.47 1.93 483.62 862.00 5,000.00 16,731.09 6,065.02 1,250.00 7,315.02 365.75 484.51 10.09
49 40.50 2.74 274.52 103.59 10,526.91 1.96 490.21 862.00 5,000.00 16,879.11 6,160.36 1,250.00 7,410.36 370.52 490.82 10.02
50 41.00 2.72 278.20 104.98 10,668.15 1.99 496.78 862.00 5,000.00 17,026.94 6,255.32 1,250.00 7,505.32 375.27 497.11 9.94
51 41.50 2.70 281.88 106.37 10,809.22 2.01 503.35 862.00 5,000.00 17,174.57 6,349.93 1,250.00 7,599.93 380.00 503.38 9.87
52 42.00 2.69 285.55 107.76 10,950.11 2.04 509.91 862.00 5,000.00 17,322.03 6,444.21 1,250.00 7,694.21 384.71 509.62 9.80
53 42.50 2.67 289.22 109.14 11,090.85 2.07 516.47 862.00 5,000.00 17,469.31 6,538.15 1,250.00 7,788.15 389.41 515.84 9.73
54 43.00 2.66 292.89 110.52 11,231.43 2.09 523.01 862.00 5,000.00 17,616.44 6,631.77 1,250.00 7,881.77 394.09 522.05 9.67
55 43.50 2.64 296.55 111.91 11,371.86 2.12 529.55 862.00 5,000.00 17,763.42 6,725.09 1,250.00 7,975.09 398.75 528.23 9.60
56 44.00 2.63 300.21 113.29 11,512.16 2.14 536.09 862.00 5,000.00 17,910.25 6,818.11 1,250.00 8,068.11 403.41 534.39 9.54
57 44.50 2.61 303.86 114.67 11,652.33 2.17 542.61 862.00 5,000.00 18,056.95 6,910.84 1,250.00 8,160.84 408.04 540.53 9.48
58 45.00 2.60 307.52 116.04 11,792.38 2.20 549.14 862.00 5,000.00 18,203.51 7,003.30 1,250.00 8,253.30 412.66 546.65 9.43
59 45.50 2.59 311.17 117.42 11,932.30 2.22 555.65 862.00 5,000.00 18,349.96 7,095.48 1,250.00 8,345.48 417.27 552.76 9.37
60 46.00 2.57 314.81 118.80 12,072.12 2.25 562.16 862.00 5,000.00 18,496.28 7,187.41 1,250.00 8,437.41 421.87 558.85 9.31
61 46.50 2.56 318.45 120.17 12,211.82 2.27 568.67 862.00 5,000.00 18,642.49 7,279.09 1,250.00 8,529.09 426.45 564.92 9.26
62 47.00 2.55 322.09 121.55 12,351.43 2.30 575.17 862.00 5,000.00 18,788.60 7,370.53 1,250.00 8,620.53 431.03 570.98 9.21
63 47.50 2.54 325.73 122.92 12,490.93 2.33 581.67 862.00 5,000.00 18,934.60 7,461.73 1,250.00 8,711.73 435.59 577.02 9.16
64 48.00 2.53 329.37 124.29 12,630.35 2.35 588.16 862.00 5,000.00 19,080.50 7,552.70 1,250.00 8,802.70 440.13 583.04 9.11
65 48.50 2.52 333.00 125.66 12,769.67 2.38 594.65 862.00 5,000.00 19,226.32 7,643.45 1,250.00 8,893.45 444.67 589.05 9.06
66 49.00 2.50 336.63 127.03 12,908.91 2.40 601.13 862.00 5,000.00 19,372.04 7,733.99 1,250.00 8,983.99 449.20 595.05 9.02
67 49.50 2.49 340.26 128.40 13,048.06 2.43 607.61 862.00 5,000.00 19,517.67 7,824.32 1,250.00 9,074.32 453.72 601.03 8.97
68 50.00 2.48 343.89 129.77 13,187.14 2.46 614.09 862.00 5,000.00 19,663.23 7,914.45 1,250.00 9,164.45 458.22 607.00 8.93
69 50.50 2.47 347.51 131.14 13,326.14 2.48 620.56 862.00 5,000.00 19,808.70 8,004.38 1,250.00 9,254.38 462.72 612.96 8.88
70 51.00 2.47 351.14 132.50 13,465.07 2.51 627.03 862.00 5,000.00 19,954.10 8,094.13 1,250.00 9,344.13 467.21 618.90 8.84
71 51.50 2.46 354.76 133.87 13,603.93 2.53 633.49 862.00 5,000.00 20,099.42 8,183.69 1,250.00 9,433.69 471.68 624.84 8.80
72 52.00 2.45 358.38 135.24 13,742.72 2.56 639.96 862.00 5,000.00 20,244.68 8,273.07 1,250.00 9,523.07 476.15 630.76 8.76
73 52.50 2.44 361.99 136.60 13,881.45 2.59 646.42 862.00 5,000.00 20,389.87 8,362.27 1,250.00 9,612.27 480.61 636.66 8.72
74 53.00 2.43 365.61 137.97 14,020.12 2.61 652.88 862.00 5,000.00 20,535.00 8,451.31 1,250.00 9,701.31 485.07 642.56 8.68
75 53.50 2.42 369.22 139.33 14,158.73 2.64 659.33 862.00 5,000.00 20,680.06 8,540.19 1,250.00 9,790.19 489.51 648.45 8.65
76 54.00 2.41 372.84 140.69 14,297.28 2.66 665.78 862.00 5,000.00 20,825.06 8,628.90 1,250.00 9,878.90 493.95 654.32 8.61
77 54.50 2.41 376.45 142.06 14,435.78 2.69 672.23 862.00 5,000.00 20,970.01 8,717.46 1,250.00 9,967.46 498.37 660.19 8.57
78 55.00 2.40 380.06 143.42 14,574.22 2.71 678.68 862.00 5,000.00 21,114.90 8,805.87 1,250.00 10,055.87 502.79 666.05 8.54
79 55.50 2.39 383.67 144.78 14,712.62 2.74 685.12 862.00 5,000.00 21,259.74 8,894.14 1,250.00 10,144.14 507.21 671.89 8.50
80 56.00 2.38 387.28 146.14 14,850.96 2.77 691.57 862.00 5,000.00 21,404.53 8,982.26 1,250.00 10,232.26 511.61 677.73 8.47
90 60.00 2.29 417.43 157.52 16,007.20 2.98 745.41 862.00 5,000.00 22,614.61 9,893.89 1,250.00 11,143.89 557.19 738.11 8.20
100 61.00 2.12 429.43 162.05 16,467.32 3.07 766.83 862.00 5,000.00 23,096.16 10,909.15 1,250.00 12,159.15 607.96 805.36 8.05
200 62.00 1.15 466.32 175.97 17,882.24 3.33 832.72 862.00 5,000.00 24,576.96 21,356.19 1,250.00 22,606.19 1,130.31 1497.31 7.49
500 63.00 0.49 494.61 186.64 18,966.85 3.53 883.23 862.00 5,000.00 25,712.08 52,623.03 1,250.00 53,873.03 2,693.65 3568.26 7.14
Number of trip in working day of 8 hours N = 8/((2L/S)+1), Where L = Lead in Km, S = Speed in Km per hour, 1/2 hour is allowed for loading / unloading.
Consumption of diesel taken at 3 Km per litre.
Consumption of mobile oil taken at 140 Km per litre.
Cost of labour, hire charges of truck, diesel and mobile has been taken from the basic rate sheet. Loading is to be done by Precast Factory by his own crane.
Average Rate
per tonne per
km
9.95
8.84
IR Unified Standard Schedule of Rates 2019
The accessories, meeting applicable RDSO Specification No IRST/19-2020 with latest amendm
integral part of AT welding portions of respective Rail section and shall be supplied free of cos
yardstick.
Sl.No Description of Item Qty to be Supplied
**110 Units complete with every 100
1 Pre-fabricated 3 piece moulds with cake piece
Portions
2 Dry Luting Sand 3.5 Kg per portion in individual packets
3 Single Shot crucible charge 1 No for each portion
4 Auto tapping thimble 1 No for each portion
**105 Units complete with every 100
5 Ignition Matches
Portions
6 Mould shoe 1 Set per 50 Nos of Portions
7 Mould pressure clamp 1 Set per 500 Nos of Portions
8 Torch burner complete 1 Set per 200 Nos of Portions
9 Torch burner Keys 1 per 500 Nos of Portions
10 Goose neck arrangement for vaporization 1 per 500 Nos of Portions
11 Connecting Hose pipe 1 per 1000 Nos of Portions
12 Torch burner stand 1 per 1000 Nos of Portions
13 Aluminium / Steel rod for thermal plugging 1 per 800 Nos of Portions
14 Stop Watch 1 per 800 Nos of Portions
15 Adjustment spanner 1 per 800 Nos of Portions
16 Hot sets Chisels for emergency use 1 per 500 Nos of Portions
17 Pliers 1 per 800 Nos of Portions
18 Steel Wire brush 1 per 400 Nos of Portions
19 Slag Container Bowl 1 per 500 Nos of Portions
Weld Grinding Stone (Top Flexible High speed)
20 1 per 10 Nos of Portions
(150x120x50/22.23) mm)
Trimmer cutter hydraulic pressure pipe with
21 1 pipe per 300 Portions
connecting arrangement
22 Trimmer Cutter Blade (Fixing arrangement) 1 Set per 300 portions
23 Rail cover 1 Set per 100 portions
24 Hammer 1016 2 Nos per 800 portions
25 Thermal Chalks 1 per 800 Portions
26 10 cm Long Gauge 1 per 800 Portions
27 1 m long Gauge 1 per 800 Portions
28 Filler Gauge shims 1 per 800 Portions
29 Pressure Gauge 2 Nos per 800 portions
30 Weld Cover 1 Nos per 800 portions
IR Unified Standard Schedule of Rates 2019
Annexure I
ent, are considered
st as per following
Remarks
1. The quantity to be
supplied shall be in
whole Nos in the
specified ratio or
part thereof.
2.**Extra quantity
towards
damages/breakages
etc., and the rates
quoted are inclusive
of this extra quantity
and no extra
payment will be
there

Irussor Aor 2021 Draft

Uploaded by

Copyright:

Available Formats

Irussor Aor 2021 Draft

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Irussor Aor 2021 Draft

Uploaded by

Copyright:

Available Formats

DRAFT AOR

भारतीय रे ल एकीकृ त मानक दर

General and Operating Instructions

3. Units used in IRUSSOR

TRM Track Metre

"Basic Input Data Sheet"

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

181 Diesel (HSD) Oil Litre 0181 101.62

217 CRCA Sheathing Metre 0217 165.00

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

302 Solvent confirming to IS Specification 1745-1976. Litre 0302 150.00

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

(Rates of the Basic Elements are without GST)

SL Description Unit Rate Rate (Rs)

CHAPTER - 1 : Earth Work

Considering bank height of 5m, formation width 8m additional clearance of 0.5m on

011020 Benching of existing embankment manually in steps of 30 cm height for

Detail of cost for 1 Km of 3 metres height of the embankment

Item no. Description Unit Rate Rate Quantity Amount

011031 Using Soil Class SQ1

011032 Using Soil Class SQ2

Item no. Description Unit Rate Rate Quantity Amount

011033 Using Soil Class SQ3

012000 Earthwork in New Lines, Doubling Projects Etc. - Cuttings

012011 In all conditions and classifications of soil except rock

Item no. Description Unit Rate Rate Quantity Amount

012012 Soft rock not requiring blasting

012013 In hard rock requiring blasting

Item no. Description Unit Rate Rate Quantity Amount

Considering cost for 30,000 Sqm

Item no. Description Unit Rate Rate Quantity Amount

Cost of transportation cum 159.89 197.57 31,588.65

Item no. Description Unit Rate Rate Quantity Amount