Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 63 views

    T103 Instructions

    Uploaded by

    jtcool74
    This document provides instructions for a 24 hour dial time switch with the following specifications: - Double pole single throw (DPST) switch rated for 40 amps resistive, inductive, tungsten or 1000 VA pilot duty loads at 120/208-240V AC. - The clock motor operates on 110-125V AC, 60Hz. - Wiring instructions and terminal specifications are provided for making power connections to the switch. - Programming instructions explain how to set the on/off times using tripper switches on the dial and how to set the time of day. - Operating instructions describe how to manually operate the switch and how to reset it in case of a power failure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    T103 Instructions

    Uploaded by

    jtcool74
    63 views1 page
    This document provides instructions for a 24 hour dial time switch with the following specifications: - Double pole single throw (DPST) switch rated for 40 amps resistive, inductive, tungsten or 1000 VA pilot duty loads at 120/208-240V AC. - The clock motor operates on 110-125V AC, 60Hz. - Wiring instructions and terminal specifications are provided for making power connections to the switch. - Programming instructions explain how to set the on/off times using tripper switches on the dial and how to set the time of day. - Operating instructions describe how to manually operate the switch and how to reset it in case of a power failure.

    Original Title

    T103_Instructions

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for a 24 hour dial time switch with the following specifications: - Double pole single throw (DPST) switch rated for 40 amps resistive, inductive, tungsten or 1000 VA pilot duty loads at 120/208-240V AC. - The clock motor operates on 110-125V AC, 60Hz. - Wiring instructions and terminal specifications are provided for making power connections to the switch. - Programming instructions explain how to set the on/off times using tripper switches on the dial and how to set the time of day. - Operating instructions describe how to manually operate the switch and how to reset it in case of a power failure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    63 views1 page

    T103 Instructions

    Uploaded by

    jtcool74
    This document provides instructions for a 24 hour dial time switch with the following specifications: - Double pole single throw (DPST) switch rated for 40 amps resistive, inductive, tungsten or 1000 VA pilot duty loads at 120/208-240V AC. - The clock motor operates on 110-125V AC, 60Hz. - Wiring instructions and terminal specifications are provided for making power connections to the switch. - Programming instructions explain how to set the on/off times using tripper switches on the dial and how to set the time of day. - Operating instructions describe how to manually operate the switch and how to reset it in case of a power failure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    MODEL: T103 LR3730

    24 HOUR DIAL TIME SWITCH


    DOUBLE POLE SINGLE THROW (DPST)
    40 AMP. RESISTIVE, INDUCTIVE, TUNGSTEN OR
    1000 VA PILOT DUTY EACH POLE 120/208.240 VOLT AC;
    2 HP (24 FLA)-120V AC; 5 HP (28 FLA)-240V AC.
    CLOCK MOTOR: 110-125 VOLTS - 60 HZ.
    CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO
    ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
    TYPICAL
    ON WIRING
    TIME TRIPPER
    DIAL DIAGRAM CLOCK
    MOTOR
    TIME
    POINTER
    120/240 A 1 2 3 4
    NEUT.
    OFF VOLT
    3 WIRE LINE 1
    TRIPPER TO
    SUPPLY LINE 2 LOADS
    MANUAL
    LEVER GROUND
    GR.

    WIRING INSTRUCTIONS: To wire switch follow diagram above.


    Use solid or stranded COPPER only wire with insulation to suit
    installation. See gauge selection table for normal service applica-
    tions. To make power connections remove 1/2 inch of insulation
    from wire ends. Insert bare ends of wire under the pressure plate
    of terminals. Use 3/16 or larger screwdriver to tighten terminal
    screws firmly. (25 lb-in minimum).
    REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
    MINIMUM MAX. MIN. 75°C INSULATION MAX. MOTOR
    COPPER LOAD INSUL- LOAD (HP) PRESSURE PLATE
    WIRE SIZE (AMP) ATION SINGLE PHASE 3 PHASE
    (AWG) TEMP (°C)
    120 V. 240 V. 208 V.
    TERMINAL SCREW
    240 V.
    14 15 60 1/2 2
    MAKE SURE WIRE
    12 20 60 1 2 1/2 INSULATION
    N/A N/A
    10 30 60 2 3 CLEARS
    8 40 75 - 5 PRESSURE PLATE
    PROGRAMMING INSTRUCTIONS
    1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge
    of CLOCK-DIAL, pointing to time (AM or PM) when ON and
    OFF operations are desired, tighten tripper screws firmly. For
    additional tripper pairs on CLOCK-DIAL order 156T1978A.
    2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in
    either direction and align the exact time-of-day on the CLOCK-
    DIAL (the time now, when switch is being put into operation) to
    the pointer. DO NOT MOVE POINTER.
    OPERATING INSTRUCTIONS
    • TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER
    below CLOCK-DIAL left or right as indicated by arrows. This
    will not effect next operation.
    • IN CASE OF POWER FAILURE, reset CLOCK-DIAL to
    proper time-of-day. See programming instructions
    INTERMATIC INCORPORATED
    SPRING GROVE, ILLINOIS 60081-9698
    154--01003

    You might also like