Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 170 views

    12V 38A 460W HSTNS PL14 Deployment

    Uploaded by

    Carlos Caseres

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    12V 38A 460W HSTNS PL14 Deployment

    Uploaded by

    Carlos Caseres
    170 views1 page

    Original Title

    12V-38A-460W-HSTNS-PL14-Deployment

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    170 views1 page

    12V 38A 460W HSTNS PL14 Deployment

    Uploaded by

    Carlos Caseres

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Switched Mode DC Power Supply

    12V-38A-460W-HSTNS-PL14
    http://www.casa.co.nz
    Type: © copyright: 16/01/2019

    General Installation & Operation


    DRAFT Overview:

    This DC Power Supply is a very high quality self-contained unit deemed


    usable in applications where 12V DC is required at continuous currents up to
    HP: 499250-201 62 Amps with good regulation and compact size... ...typical applications may
    include:
    General Data
    Rear Panel View & Basic Connection Details

    Brand: HP (Common Slot series)


    WARNING – output negatives are earthed LiPo battery charging, Amateur FM, SSB and TV transmitters, CNC
    machines-motor drive, original computer server systems etc..
    HP Part #: 499250-201
    Spares #: 511777-001 Operation: Deploy adequately sized cable etc., for connection to the mains
    Model: HSTNS-PL14 supply and the DC output. Add the appropriate control wire jumpers or
    OEM: PS-2461-1C-LF LITE-ON switches etc. to render the supply operational.

    Input Voltage: 100~240V The supply requires two additions to bring the supply into Run mode, a
    Input Current: Up to 6A @100V, 3A @240V jumper from 33 to -ve and a 22k resistor from 36-37. The fan runs at low
    Mains Input Connection: IEC C14 chassis plug speed while the supply is cool and speeds up with increasing temperature.
    Output Voltage: 12.0V (internally adjustable -/+?%) An optional SPST switch in the GND – 33 line will allow the 12V supply to be
    Output Current: Up to 38.3 Amps (tested to 42A) shut down reducing the fan noise without disabling the 12 Volt SB supply.
    Remote Sensing: No
    Minimum Load Current: 1% (will run no-load)
    33 PCB Top View 64
    Mounting: These units were originally deployed in 19" rack-mounted hot-
    Over current protection: Yes (%?) swap sleeves (as part of a major computer server infrastructure) and only
    Over/Under voltage protection: Yes -ve (Gnd) +12V require adequate ventilation at the ends to facilitate un-interupted air-flow of
    Management Voltage: 12V Standby Output the internal axial fan.
    Management Current: up to 2.5A Note - Free-standing or custom fixing is at the discretion of the user.
    Total Output power: 460W 22k
    Operating temperature: +5°C ~ +40°C. Adjustments: There are no external adjustments, however, for the
    Operating frequency: 50-60Hz Enable Link technically competent, some internal adjustments may be made to suit
    Conversion efficiency: Typically >95% (load dependant) special application including raising the output to 13.0V. There are various
    Power Factor: >0.90. APFC WWW resources offering ‘advice’ along these lines.
    Power indicator: Yes
    Over temperature protection: Yes Connection: In the absense of an original sleeve and mating connector,
    Wiring: PC Board Edge 0.1" pitch 2 rows of 32 pins some imagination using industry-standard practices can be applied to
    achieve practical connection to the high-current load terminations.
    Size: 240 x 86 x 40 mm (nominal LxWxH) A standard 0.1" 32 way 2 row connector will mate to the output PCB tracks.
    Fixing: Intended to sleeve mount Note - There are various WWW resources offering ‘advice’ on using the
    Weight: ~0.97kg included rear Hot-Swap connections.

    Package & Options include:


    1 PCB Bottom View 32 Control: See a typical connection and control schematic/diagram on the
    left. We welcome users comments and suggestions for improving this sheet.
    1 x 12V 38A 460W DC power supply and 22k resistor.
    Optional: IEC mains input cable, flexible 50~100A output +12V -ve (Gnd)
    cable and printed circuit board output connector
    Caution: This supply is capable of outputting destructive power levels!
    (refurbished EDAC 345-064-524-201, or equivalent, rated Suitably rated protective fusing or circuit breakers should be provided on the
    NOTICE – the information on this page is not guaranteed for 12 Volt rail to avoid the risk of fire and/or destruction of your connected
    3A per pin negotiable while stocks exist. Circuit breakers accuracy – CASA accepts no responsibility (neither expressed equipment under fault conditions.
    and other parts will be provided upon detailed request. nor implied) for any errors or the consequence therefrom.

    You might also like