TOPS-050TB2

Photo Diode LED

Chip
Part Number Lens Color
Material Source Color

TOPS-050TB2 AlGaAs Silicon Phototransistor Black

Features
• I.C. compatible.
• Low power consumption.
• Compatible with wave soldering process.
• 5mm diameter package.
• Long life, stable and reliable.
• RoHS compliant.

Dimensions

Notes:
1. All dimensions are in millimeter.
2. Tolerance is ±0.25mm unless otherwise noted.

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 1/7
Notes: Above specification may be changed without notices.
Absolute Maximum Rating @ Ta=25°C

Parameter Symbol Rating Unit

Collector-Emitter Voltage VCEO 30 V

Emitter-Collector Voltage VECO 5 V

Collector Current Ic 20 mA

Operating Temperature Range Topr -40 to +85 ℃

Storage Temperature Range Tstg -40 to +100 ℃

Lead Soldering Temperature

Tsol 260 for 5 Sec ℃
(1/16 inch from body for 5 sec.)

Power Dissipation at (or below)25℃

PD 100 mW
Free Air Temperature

Electrical / Optical Characteristic @ Ta=25°C

Parameter Symbol Min. Typ. Max. Unit Test Condition

Ic=100µA
Collector-Emitter Breakdown Voltage BVCEO 30 - 110 V
IB=0
IE=100µA
Emitter - Collector Breakdown Voltage BVECO 5 - - V
IB=0

Rang of Spectral Wavelength λ 750 - 1050 nm -

Peak of collection Wavelength λP - 940 - nm -

Rise Time tR - 20 - VCE=5V

µS Ic=1mA
Fall Time tF - 20 - RL=1000Ω

VCE=10V
Collector Dark Current ICEO - - 100 nA 2
H=0mW/cm

IC=20mA
Collector-emitter Saturation Voltage VCE(S) - - 0.2 V
IB=100µA

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 2/7
Notes: Above specification may be changed without notices.
Typical Electro-Optical Characteristics Curve

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 3/7
Notes: Above specification may be changed without notices.
Reliability Test Project

Samples(n)
Test Items Test Conditions Failure Judgement Criteria
Defective(c)

Operation life VCE=5V，Ta：25℃ 1000Hrs n=22，c=0

1 cycle-55℃ to +25℃ to +85℃

Temperature cycle (30min) (5min) (30min) n=22，c=0
50 cycle test
-10℃ to +100℃
Thermal shock (5min)(5sec)(5min) n=22，c=0
50 cycle test
Ic(on)≤Lx0.8
High temperature storage Temp：+100℃ 1000Hrs L：Lowe specification limit n=22，c=0

Low temperature storage Temp：-40℃ 1000Hrs n=22，c=0

High temperature storage

Ta：85℃ RH：85% 1000Hrs n=22，c=0
High humidity
Temp：260±5℃ 5sec
Solder heat 4mm From the bottom of the n=22，c=0
package.
Temp：230℃±5℃ 5sec
More than 90% of Lead to be
Solderability 4mm From the bottom of the n=22，c=0
covered by soldering
package.

Judging criterion

Experiment Criteria
Item Symbol
condition Min. Max.

Forward Voltage VF IF=20mA - Initial Datex1.1

Reverse Current IR VR=5V - 30µA

Luminous Intensity IV IF=20mA Initial Datex0.7 -

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 4/7
Notes: Above specification may be changed without notices.
Package Description

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 5/7
Notes: Above specification may be changed without notices.
Cautions

LED bracket forming method :

1. The pin of led can be bent where is at least 3mm out of led colloid.
2. Must use fixture to deform the led bracket.
3. Finishing the forming of led bracket must be before soldering.
4. Guarantee the gap between two pin of led tallys with LED pads in PCB when forming.

Manual soldering :
The tip temperature of soldering iron don’t exceed 260℃；soldering time don’t exceed 3s and soldering
position must be 3mm out of led colloid。

Soldering temperature curve chart（figure A、figure B）:

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 6/7
Notes: Above specification may be changed without notices.

ESD countermeasure
Static electricity and high volt can damage led. The production whose Die material is InGaN must strictly
required to prevent ESD, must put on static glove and static fillet. Soldering tool and the cover of device must
connect the ground, soldering condition follows the related stating of production specification manual.

Protecting countermeasure when over current

Need add the protecting resistor in circuit in order to avoid damaging led due to big current and voltage
fluctuation.

LED installation method

1. Pay attention to the led polarity and avoid installation wrong. LED can’t be close to euthermic component，
work condition should tally with it’s specification.
2. Don’t install the LED under the condition of the led pin deformation.
3. The led bracket don’t load any pressure when installing the led into PCB or fitting hole.
4. Must avoid any strike and force on led before the soldering temperature return to room temperature.

Storage time
1. LED can be stored for a year under the condition:
the temperature of 5℃～35℃ and humidity of RH60%, These production must be re-inspected and tested
before use if their storage time exceed a year.
2. If LED is exposed in air for a week under the condition:
the temperature of 5℃～35℃, humidity of RH60%，must place the led in the ambience of 65℃±5℃ for 24
hours and use it in 15 days for best.

Cleaning
Be careful of some chemical results in the led colloid fades and damage when using chemical clean the LED
such as chloroethylene, acetone etc. can use ethanol to wash or soak LED but the time don’t exceed 3
minutes.

Kinked
The kinked tooling scrape easily the pin of LED, where the led bracket is rusting easily, especial expose it in
moist air. To decrease the led bracket rust, suggest using plated tin led bracket.

REV.: A-2 Prepared by WY.Lai(30950) Released Date: 2018/08/15 Doc No : GL1808030 Page 7/7
Notes: Above specification may be changed without notices.