Alpha 4-8-12

Installation Manual Document : 01 NGP 1145
ALPHA 4/8/12 GBR Index :B

Conventional Fire Alarm Control Date : 19/03/04
Panel Page : 1/34
Conventional fire alarm panel
ALPHA 4/8/12
Installation
Commissioning
Operation
Panel Page : 2/34
SUMMARY
INTRODUCTION ............................................................................. 3
INSTALLATION .............................................................................. 4
Mounting ...................................................................................................................... 4
Connections ................................................................................................................ 4
COMMISIONING ............................................................................. 5
Preliminary inspections.............................................................................................. 5
Configuration............................................................................................................... 6
Panel configuration..................................................................................................... 8
CONTROLS AND TESTS ............................................................. 17
Connection ................................................................................................................ 17
Test power supply..................................................................................................... 17
Working tests ............................................................................................................ 17
Final work .................................................................................................................. 18
Electrical and mechanical characteristics .............................................................. 19
Relay card .................................................................................................................. 20
Electrical characteristics of extinguishing card..................................................... 20
Type of Actuators and Type of command............................................................... 20
APPENDIX .................................................................................... 21
Mechanical drawing .................................................................................................. 21
Mains connecting plan ............................................................................................. 22
Panel connecting plan .............................................................................................. 23
Detector and Sounders connection plan ................................................................ 24
Extinguishing configuration and connecting plan................................................. 26
Input lines connection .............................................................................................. 27
Output connection .................................................................................................... 28
Checklist Commissioning ........................................................................................ 29
User Maintenance / System Inspection................................................................... 30
12 relay card configuration and connecting plan .................................................. 31
Operation instructions of Extinguishing module................................................... 33
Operation instructions.............................................................................................. 34
Panel Page : 3/34
INTRODUCTION
This manual provides information of the conventional fire alarm panel ALPHA 4/8/12.
• ALPHA 4/8/12 Basic panel with 4 lines
• EX4A4 Option: 4 line extension card
• REP4R Option: 4 relays card
• R12P2 Option: 12 relays card
• DEAG Option: extinguishing card
The document includes instructions about

• installation
• operation
• commissioning
• analysis of deficiencies
• technical specification
The following information is given to benefit the safety of persons, to avoid damaging the installed
equipment and to ensure the correct operation of the system.
The whole panel documentation shall be printed and placed close to the panel.
All modules are designed to comply with the EN 54-2 and EN 54-4 standards and with the draft of EN
12094-1 standard for the extinguishing part.
In addition to this document, these following items are necessary:

• One screwdriver TORX T10, one digital or analogue multimeter, one chronometer, an
appropriate detector test product in accordance to the installed detectors
• The installation drawing of products on the site
• The specific installation drawing of each associated product
(point -, beam -,aspirating detectors,…).
Access levels
The operation access to the panel is divided on 3 levels
Level 1 direct access for all personnel (no code).

No safety relevant operation is enabled
Level 2 protected access for operator / safety officer (by digital code).
Safety relevant operation is enabled. E.g. switch detection lines on/off
Level 3 protected access for installer (by digital code).

For configuration and maintenance. E.g. set a delay time for alarm and set
association of detection line to the extinguishing channel.
Caution :
Before any intervention on the power supply of the equipment, make sure the mains (230V) is
powered down using the external device of the building's electrical installation.
Panel Page : 4/34
INSTALLATION
Mounting
Fix the panel box to the wall using the 3 attaching holes (see drawing in the appendix)
The installation of the two batteries and the optional cards will be done during the commissioning.
Other equipment refer to their individual instruction manuals.
Connections
Cable inlets
In order to keep the initial degree of protection (IP31), the cables will enter either by the preformed
orifice plate at the bottom or at the back of the box.
Do not connect the wires at the panel now, the connections will be done during the commissioning.
Power supply
The panel will be powered from the mains (230 VAC 50 Hz).
Use the mains terminal block of the cabinet (at the right bottom).
A dedicated power line shall be used for the fire security.
The line shall be protected against high voltage peaks and high frequency voltage.
The panel has to be connected to electrical earth.
(Recommendation:
Use the earth of weak signal equipment: «weak current earth» or «computing earth».
Cable types
Part Line type Wire type

Cabinet Mains 3 x 1.5mm² (2P +E)
Main card Fire detection lines Up to 500 m: 2x 0.5mm²
Up to 1000 m: 2x 1.0mm²
Up to 1500 m: 2x 1.5mm²
Up to 2000 m: 2x 2.0mm²
Up to 2500 m: 2x 2.5mm²
Recommendation:
Pair-wise twisted and shielded
24VDC Output 2 x 1.5mm² or 2 x 2.5mm²
Internal repetition by relay Cable (pre installed)
(optional)
Sounders 2 x 1.5mm² or 2 x 2.5mm²
Cable protected according to national standard
Programmable input ≥ 1 mm² (maximum length = 1Km)
Extension card Fire detection lines See under main card
Relay Card Information transmit ≥ 2x 0.5mm²
Extinguishing -Extinguishing Manual Call ≥ 2x 1 mm² (maximum length = 1Km)
Card Point Input
-Remote inhibition Input
-Low pressure Contact
Input
24V external power supply ≥ 2x 1.5 mm²
for evacuation indicators
and extinguishing
actuators
-Extinguishing indicators ≥ 2x 1.5 mm²
-Extinguishing actuators
Panel Page : 5/34
COMMISIONING
Preliminary inspections
Line checks
Before connecting and powering up the panel, the monitored lines for
• Detectors
• Sounders and Extinguishing indicators, Extinguishing actuators if used
• Input of main card and Inputs of Extinguishing card if used
shall be checked for their quality.
For each line, check its line resistance, rating resistance and insulation.
Line resistance «LR»

Make a short circuit at the end of the line. Measure the resistance at the beginning of the line between
the wires «+» and «-».
LR shall be < 36 Ω
Rating resistance «RR»
Remove the short circuit and connect the Line Terminal Resistor (LTR=3,9kΩ) at the end of the line.
Measure the resistance at the beginning of the line between the wires «+» and «-».
RR shall be between 3750Ω and 4200Ω
Insulation resistance «IR»

This measurements have to be done for each installation wire line of all panel cards.
Measure the resistance between each conductor (including shield) and the electrical earth.
IR ≥ 1MΩ.
Panel Page : 6/34
Configuration
Generalities
Hardware configuration:
All equipment is powered off.
(If the panel is powered, first remove the battery and then the mains.)
If there are optional cards: mount the extension or Extinguishing card(s) and make sure that the
jumper ST1 at the left card is set, and the jumper ST1 at the right card is removed.
For the Extinguishing Card(s), select the different jumpers according the chosen configuration for the
type of actuators, the actuators supply and sounders/indicators supply (see appendix).
Software configuration:
When the panel is powered, it allows to define some parameters and functions. This must be done,
every time you remove or add a card, or a parameter has to be changed.
These settings will be saved in a non-volatile memory and can be changed only be overwriting.
Powering Up
• Check the correct mains voltage (between 195VAC and 253VAC)

• Connect the mains to the terminal block of the panel.
• Put the batteries in place and connect them to the panel.
• After the activation of the LED «supply fault», connect the 2 batteries.
The panel displays «System Fault», this LED turns off after a few seconds (initialisation time), then the
fire detection lines are disabled.
Before any intervention it is indispensable to make sure that all parts

controlled by the extinguishing circuit board are disconnected.
Panel Page : 7/34
Software Parameters
As the first step, you have to enable the fire detection lines (see chapter “Enable / disable fire
detection ”). Now make the panel configuration according the site requirements.
The main parameters of the commissioning as follows:
(This is an overview. The function are described in more detail further down in this document)
Parameters Access Function
Enable/ disable fire detection line Level 2 Inhibition of information given by a fire detection line.
On/off test mode of fire detection line Level 2 Enable to test the detectors of the installation without
activation of the control device.
Detection mode (alarm on one Level 3 Allows to configure the line in 2 detectors alarm mode.
detector or on two detectors) code BABA This mode is forbidden for Manual Call Points.
Joining alarm zone with Level 3 Allows to join the alarm zone to one or several fire detection
detection zone (AZ/DZ) code ABBB zones. By default all fire detection zones are joined to the
alarm zone.
If extinguishing card is used, Allows to join the extinguishing
zone to two (minimum) or several detection zones.
Sounders delay Level 3 Delay between an alarm and the actuation of sounders line.
code BAAA 0 to 7 minutes in 1 minute steps. Default: no delay.
If extinguishing card is used, Delay between the activation
extinguishing indicators and the activation extinguishing
actuators.
Enable/ disable sounders line Level 3 Disabling of the sounders line.
code BABA
Level 2 and 3 access general mode
Access Level 2
The panel can have two different level 2 access codes (see chapter “Code modification level 2
access”)
The standard level 2 access:

Simultaneously press keys A and B: The indicator «level 2 or 3» will flash for 15 seconds.
Within this time enter the code ABAB.
Simultaneously press A and B
If the code is correct, the LED «Access level 2 or 3» will light up permanentely.
1) The simple level 2 access:

Simultaneously press keys A and B then the level 2 is activated (indicator is permanentely on).
After a timeout of 2 minutes, the access level 2 will be deactivated automatically
Access Level 3
The Level 3 can be accessed if the panel is in level 2 and if the system is not in alarm.
The level 3 access codes are described in the list above.
Indication after a valid access level 3 code:
- The LED «level 2 or 3» is off and the LED «Fault system» is blinking.
- One other LED of the main panel will activate, according to the code which has been set.
The validation of the settings is done either automatically or by pressing the «Reset» key, depending
on the chosen function.
The level 3 exit is done by pressing the key «Silence Buzzer».
Panel Page : 8/34
Panel configuration
Enable / disable fire detection zones, or enable / disable manual mode and/or automatic mode
of extinguishing module
FUNCTIONS For the fire detection cards:

Allows to enable / disable fire detection line(s) in order to activate or inhibit
informations given by a fire detection line.
For the extinguishing module:
Allows to enable / disable the automatic mode and/or the manual mode.
CODE Level 2
STATE LED « ACCESS LEVEL 2 or 3 » is on
KEY and LED Fire detection:
• Press the key « LEVEL 2 » of the function « DISABLE (TEST) » of
each zone to switch the line on and off.
• LED « FAULT/DISABLED/TEST » :
On = line is switched off
Off = line is switched on
Extinguishing:
• Press the key « LEVEL 2 » of « AUTOMATIC MODE
DISABLED/MANUAL MODE DISABLED » to enable or disable each
mode
• LED « AUTOMATIC MODE DISABLED » and/or LED « MANUAL
MODE DISABLED » :
On = automatic mode or manual mode disabled
Off = automatic mode or manual mode enabled
Enable/disable the test mode of detection zones and/or extinguishing channel
FUNCTIONS Allows to activate the test mode of each detection zone and/or extinguishing
channel.
CODE Level 2
STATE LED « ACCESS LEVEL 2 OR 3 » is on
KEY and LED • Press the key « LED – BUZZER TEST »
• LED « TEST » on

each detection zone or extinguishing card to switch into test mode.
• LED « FAULT/DISABLED/TEST» :
Slow blinking = test mode activated
For exit of test mode press « RESET PANEL » (see note below )
Note: Once the zones have been programmed in test mode wait 10s before pressing « RESET
PANEL » for exit. Exit of test mode is possible only when the zones in test mode are no longer in
alarm status. On the other hand, you can reach Level 3 from test mode and this way disable test mode
without taking the delay of 10s into account.
Panel Page : 9/34
2 detectors mode
FUNCTIONS 1) Allows to activate Mode 1 (single detection) or Mode 2 (double detection) for
each detection zone.
• Mode 1: Zone switches into alarm status if one detector is in alarm
• Mode 2: Zone switches into alarm status if a second detector of the
same zone is in alarm.
2) Allows to check the mode of each zone
CODE At level 2, set the code BABA, then press AB simultaneously
STATE LED « SYSTEM FAULT » is blinking
LED « FAULT WARNING » in on
KEY and LED • Press the key « LEVEL 2 » of the function « DISABLE (TEST) » of
each detection zone to switch the line from mode 1 to mode 2 or from
mode 2 to mode 1.
• LED « FAULT/DISABLED/TEST »:
Off = mode 1
On = mode 2
To validate this setting you must reset the panel by pressing the key «
SILENCE BUZZER »
Note: After any setting in double detection mode you must validate this mode by pressing the key «
ON/OFF » of the function « DAY/NIGHT » (LED « ACTIVE » on). This manipulation will be done under
access Level 2.
Enable / disable sound broadcasters line
FUNCTIONS 1) Allows to enable/disable the line of the main card dedicated to sound
broadcasters.
2) Allows to check the state of the sounders line (on or off)
CODE At level 2, set the code BABA, then press AB simultaneously
LED « FAULT WARNING » is on
KEY and LED • Press the key « ON/OFF » of the sounders line to switch on/off the
line.
• LED « FAULT WARNING » of the sounders line :
Off = Line is on
On = Line is off
To validate this setting you must reset the panel by pressing the key «
SILENCE BUZZER »
Panel Page : 10/34
Alarm zone and detection zone association
FUNCTIONS 1) Allows to associate one or several detection zones DZ to the alarm zone AZ
Note: The alarm zone AZ corresponds to the line of the main card dedicated to
the sound broadcasters.
2) Allows to check the association « AZ/DZ »

CODE At level 2, set the code ABBB, then press AB simultaneously
LED « TEST » is on
KEY and LED Check
• Press the key « ON/OFF » of the sounders line.
• LED « EVACUATE » of the sounders line is on.
• LED « FAULT/DISABLED/TEST » of each detection zone DZ associated
to the alarm zone AZ is on.
For exit you must reset the panel by pressing the key « SILENCE BUZZER »
Association setting
( you must be in check mode)
• Press the key « LEVEL 2 » of the function « DISABLE (TEST) » to
associate or not the chosen detection zone to the alarm zone.
On = DZ associated to AZ
Off = DZ not associated to AZ
Validation
• Press the key « RESET PANEL » to save the association settings and
for exit of setting.
• LED « EVACUATE » of the sounders line is off.
Note: As long as you have not reset the panel you can reach the
association setting by pressing « ON/OFF » of the sounders line. Then a
new association setting can be done.
Exit
Press the key « SILENCE BUZZER » to return to standard operation
Panel Page : 11/34
Extinguishing zone and detection zone association
FUNCTIONS 1) Allows to associate two (minimum to activate the extinguishing zone) or

several detection zones DZ to the extinguishing zone EZ
2) Allows to check the association « EZ/DZ »

CODE At level 2, set the code ABBB, then press AB simultaneously
LED « TEST » is on
KEY and LED Check
• Press the key « LEVEL 2 » of the function « (TEST) DISABLED » of the
extinguishing card.
• LED « (TEST) DISABLED » of extinguishing card is on.
• LED « FAULT/DISABLED/TEST » of each detection zone DZ associated
to the extinguishing zone EZ is on.
For exit you must reset the panel by pressing the key « SILENCE BUZZER »
Association setting
( you must be in check mode)
• Press the key « LEVEL 2 » of the function « DISABLE (TEST) » to
associate or not the chosen detection zone to the extinguishing zone.
On = DZ associated to EZ
Off = ZD not associated to EZ
Validation
• Press the key « RESET PANEL » to save the association settings and
for exit of setting.
• LED « (TEST) DISABLED » of the extinguishing line is off.
Note: As long as you have not reset the panel you can reach the association
setting by pressing « LEVEL 2 » of the function « (TEST) DISABLED » of the
extinguishing card. Then a new association setting can be done.
Exit
Press the key « SILENCE BUZZER » to return to standard operation
Panel Page : 12/34
Sounders delay
FUNCTIONS 1) Allows to apply a delay for the activation of the sounders line.
2) Allows to check the delay.

CODE At level 2, set the code BAAA, then press AB simultaneously
LED « DISABLED » is on
LIMITS 0 to 7 minutes in 1 minute steps
KEY and LED Check
• Press the key « ON/OFF » of the sounders line.
The main card displays the programmed delay as follows :

• LED « FAULT WARNING » of sounders line is on = 1 min
• LED « EVACUATE » of sounders line is on = 2 min
• LED « ACTIVE » of the function « DAY/NIGHT » is on = 4 min
• The various combinations of those LEDS allow to read a delay from 0
to 7 minutes
• All the LEDS are off = no delay
You must reset the panel by pressing the key « SILENCE BUZZER » for exit
Setting
(You must be in check mode)
• Press the key A or B to decrease or to increase the delay.
Validation
• Press the key « RESET PANEL » to save the settings.
Exit
Press the key « SILENCE BUZZER » to return to standard operation.
Panel Page : 13/34
Extinguishing delay
FUNCTIONS 1) Allows to apply a delay for the activation of the extinguishing zone.
2) Allows to check the delay.

CODE At level 2, set the code BAAA, then press AB simultaneously
LIMITS 0 to 60 seconds in 10 seconds steps
KEY and LED Check
• Press the key « LEVEL 2 » of the function « AUTOMATIC/MANUAL
MODE DISABLED » of the extinguishing card to select the mode which
you want to apply an extinguishing delay on.
• LED « AUTOMATIC MODE DISABLED » is on if you select automatic
mode or LED « MANUAL MODE DISABLED » is on if you select
manual mode.
For automatic mode or manual mode, the extinguishing card displays the
programmed delay as follows :
• LED C (at the right) of the function « FAULTS IDENTIFICATION » is
on = 10s
• LED B (at the middle) of the function « FAULT IDENTIFICATION » is
on = 20s
• LED A (at the left) of the function « FAULT IDENTIFICATION » is on =
40s
• The various combinations of those LEDS allow to read a delay from 0
to 60 seconds.
• All the LEDS are off = no delay
You must reset the panel by pressing the key « SILENCE BUZZER » for exit
Setting
(You must be in check mode)
• Press the key « LEVEL 2 » of the function « TEST (DISABLED) » of
the extinguishing card to decrease or increase the delay of one or the
other of the 2 modes.
Validation
Exit
Press the key « SILENCE BUZZER » to return to standard operation.
Panel Page : 14/34
Modification of access code level 2 and modification of the faults delay for zones of the main
card
FUNCTIONS 1) Allows to modify or to check the access code level 2
2) Allows to modify the faults delay for zones of the main card.
CODE At level 2, set the code AAAA, then press AB simultaneously
STATE LED « SYSTEM FAULT » is on
LED « EVACUATE » of the sounders line is on
KEY and LED Simple access code level 2
• Press the key A to install the simple access code level 2.
• LED « FIRE ALARM » of zone 1 is on.
Standard access code level 2

• Press the key B to install the standard access code level 2.
• LED « FIRE ALARM » of zone 2 is on
Short delay (only for the 4 detection zones of the main card):
zone 4 to set a short delay (1 s for a short-circuit and 4 s for an open
circuit).
• LED « FAULT/DISABLED/TEST » of zone 4 is on = short delay.
Standard delay (only for the 4 zones of the main card):

zone 3 to set a short delay (20 s for a short-circuit and 30 s for an open
circuit).
• LED « FAULT/DISABLE/TEST » of zone 3 is on = standard delay.
Note: For the detection zones of the optional cards, the delay remains the
same (1 s for a short-circuit and 12 s for an open circuit).
For the extinguishing card, the delay remains the same (5 s for a
short/open circuit in the low pressure line, 2 s for a short/open circuit in the
manual extinguishing line, 1 s for a short/open circuit in the 3 others lines).
Validation and exit:

Press the key « SILENCE BUZZER » to valid the settings and to reset the
system.
Remarks
Simple access code level 2 = «AB»
Standard access code level 2 = «AB, A,B,A,B, AB»
Panel Page : 15/34
Setting of the 4 open collector outputs
FUNCTIONS Allows to charge an event to each of the 4 open collector outputs.

The panel has 4 open collector outputs (OC1 …. OC4) associated to the 4
detection zones. The association is the following: OC1/DZ1, OC2/DZ2,
OC3/DZ3 and OC4/DZ4.
CODE At level 2, set the code BBBB, then press AB simultaneously
STATE LED « ACCESS LEVEL 2 OR 3 » slow blinking
KEY and LED Selection of the output(OC1 …OC4)
• Press the key « LEVEL 2 » of the function « DISABLE (TEST) » of the
corresponding zone.
Output setting
Successively press the key «A» or «B» to select the function as follows:
• LED « FIRE ALARM » of detection zone is on (standard mode)
• LED « FIRE ALARM » of detection zone is blinking (mode 2 detectors,
if mode « DAY/NIGHT » activated)
• LED « FIRE ALARM » of the main card for mode 2 detectors (if used)
is blinking
• LED « DISABLED » is on
• LED « TEST » is on
• LED « SYSTEM FAULT » is on
• LED « POWER SUPPLY FAULT » is on
• LED « FAULT WARNING » of the sounders line is on
• LED « EVACUATE » of the sounders line is on
• Active buzzer state ( short beep)
• Reset panel state (long beep)
Validation:
This will switch off the leds of the chosen zone and the chosen function.
New settings can be done at this moment. (Press the key « LEVEL 2 » of the
function « DISABLE (TEST) » of the corresponding zone).
Exit
Press the key « SILENCE BUZZER » to validate the setting and to return to
reset the system.
Panel Page : 16/34
Function of the input

This input is normally used to do an external reset.
Alternatively this input can be used to active the LED « POWER SUPPLY FAULT » or to activate the
sounders line.
FUNCTIONS Allows to charge an event to the input.

CODE At level 2, set the code AABB, then press AB simultaneously
STATE LED « SYSEM FAULT » is on
KEY and LED Setting
• Press successively the key «A» to program the input as follows:
• LED « POWER SUPPLY FAULT » is on for external supply state
monitoring
• LED « EVACUATE » is on for external activation of sounders line
• IRREGULAR BEEP for external reset panel
Validation and Exit

Press the key « SILENCE BUZZER » to validate the setting and to reset the
system.
Panel Page : 17/34
CONTROLS AND TESTS

Connection
After finishing the software configuration, connect all detection fire lines, the sounders line and the
other lines except to the extinguishing actuators according to the schematics in the appendix.
WARNING !
Before effecting any control the extinguishing actuators have to disconnect if it

is used.
Test power supply

Make the test as follows :
Control Action Result

Batteries (secondary supply) Disconnect mains (230 V). Steady LED «Power Supply Fault»
Steady LED «system fault»
Continuous Buzzer.
Mains (primary supply) Connect mains Blinking LED «Power Supply Fault»
Disconnected one wire of the Steady LED «system fault»
batteries Continuous Buzzer.
Return at initial state Connect the wires of the batteries Only the green LED «Power» is on.
Working tests
Note
These tests are a real control of the fire detection installation.
It is recommended to make these tests in a first step having the fire safety control equipment
neutralised. When the test are ok., repeat all test having the fire safety control equipment connected.
Before carrying out these tests, make sure the security department is informed about the fire alarm
testing.
Fire detection lines

For each fire detection line:
• Check if the line is in standby.
In case of problem, identify the fault at first (no LTR, bad connection, insulation fault,…).
• Plug out the line and verify if the LED « Fault/disabled/test » blinks. Then plug in the line
again.
• For a line with automatic detector heads: remove a detector from the socket and verify if the
LED « Fault/disabled/test » blinks. Then insert the detector again.
• Set the line in test mode and check the correct working of all detection points.
• Set the line in standby mode again.
• Enable all outputs and the sounder line.
• Activate one detector and verify the alarm at the panel and check the delay. Check the correct
working of sounders and other equipment associated to the evacuation.
• After 5 minutes, reset the panel.
• Disconnect the battery. Now release an alarm and check the reaction of the system.
• After 5 minutes, reset the panel.
Panel Page : 18/34
Evacuation Function
• Press the sounders key «On/Off» during 3 seconds.
• Check the LED sounders «Active» is on.
• Check the correct working of sounders and other equipment associated to the evacuation.
• Press the sounders key «On/Off» to switch off the sounders.
Extinguishing Function
• Make sure that all the monitored lines connected to the panel are in a normal status.
• In case of anomaly, identify the fault before continuing with the next test.
• For all monitored lines, Disconnect it from the panel and make sure that panel signals the
corresponding fault.
• Plug again it with the panel and make sure the fault warning disappears.
• After having checked that the actuators are disconnected, activate the automatic zone alarm
inputs and make sure the extinguishing cycle starts with the correct operations and delay.
• Reset the system and activate the manual extinguishing input and make sure the
extinguishing cycle starts with the correct operations and delay.
• Reset the system and make sure the remote inhibition line and 2nd stage MCP (Manual Call
Point) line operate correctly.
Final work
After completing the tests successfully
• Note the software settings.
• Put the line names on the panel
Hand over the system to the customer, including:
• Instruction of the responsible person(s)
• System manual
• Software settings
• Installation drawings
Panel Page : 19/34
Electrical and mechanical characteristics

ALPHA4/8/12 ALPHA4/8/12 ALPHA4/8/12
+ 1 EX4A4 + 2 EX4A4
Detector lines
Number of lines 4 8 12
Line terminal element (EOL) Resistor 3,9 KΩ, ¼ W, ± 5%
Line voltage 20VDC (between 18.5 V @100mA and 21V @0mA)
Number of detectors per line According to the list below with a maximum of 32 points
Number of manual call points per line According to the list below with a maximum of 32 points
Outputs
Output «General Fault» 1 relay,
potential free, switch over contacts 1A/30VDC
Output «Fire Alarm» 1 relay,
potential free, switch over contacts 1A/30VDC
Number of fire detection line outputs 4
Type of fire detection line outputs Open collector. 100mADC / 50 VDC. Not protected. Switch to GND.
Output «24VDC Supply» Power output protected with polyswitch, 24VDC 400mA
Input
Number of programmable input 1
Type of programmable input Monitored input with LTR = 3k9 Ω, ¼ W, ± 5%
Active by resistor 560 Ω, ¼ W, ± 5% in parallel
Sounders line
Number of sounders line outputs 1
Characteristic of sounders line output Output voltage: 24VDC, 450 mA maximum.
Line Terminal element for the sounders line Resistor 3k9 Ω, ¼ W, ± 5%
Supply
Mains voltage 230 VAC (+10, -15%), 50 – 60Hz
Mains power consumtion < 75 W
Batteries supply 2 lead-acid batteries. 12V/7.2Ah. Connected in series.
Autonomy time: approx. 24h in standby and 5 min. in alarm.
Battery voltage disconnected: 21.6V ( ±0.2V).
Current on battery : < 0.95A
Main card Current on batteries 51mA @ EOL = 3,9KΩ (30mA + 4 x 20V / EOL)
Line extension card current on batteries 35mA @ EOL = 3,9KΩ (14mA + 4 x 20V / EOL)
Supply input voltage main card Nominal: 30VAC (26 VAC to 33 VAC)
Battery voltage disconnected 21.6V ( ±0.2V)
Panel batteries 2 batteries 12V / 7.2 Ah
Panel Limitation current 0.95A by electronic protection
Mechanical Characteristics
Box ABS 5V
Colour Black RAL 7035
Dimensions Height x Width x Depth: 300 mm x 370 mm x 118 mm
Approximate weight 2 kg (without batteries)
Protection class IP31
Operating temperature range -10°C to +50°C
Storage temperature range -20°C to +60°C
Cable terminal blocks Max. wire cross section for all terminal blocks: 2.5 mm²
Wires inlets From below and from the back of the box
Others characteristics
Used components In conformity with the category 3K5 of CEI 721-3-3.
Power supply and battery charging In conformity with EN60950 standard.
Standards EN54-2 EN54-2 EN54-2
EN54-4 EN54-4 EN54-4
Admissible weighting on one detector line 35 u

Type Reference Weighting Type Reference Weighting
Ionisation smoke detector IY2 0,9 u Conventional rate of rise + fixed TVY2 2u
heat detector
Optical smoke detector OY2 2,3 u Laser beam detector for linear DLF 30 u
smoke detection
Conventional multisensor MCY2 3u Conventional manual call point BMY2 or 0 u
(optical-heat) with reset and led BMLY2
Panel Page : 20/34
Relay card
REP4R
input lines
number of lines 4
Type To be driven from ALPHA 4/8/12 open collector outputs .
Output
number of outputs 4
Type 1 relay, potential free, switch over contact 5A/230VDC
R12P2
Output
Quantity of output 12
Type 1 relay, potential free, switch over contact 30V/1A
Electrical characteristics of extinguishing card

DEAG
Input lines
Extinguishing Manual Call Point (Double Knock) Controlled line RFL = 3,9 Kohm
Active if a R = 1Kohm is connected on the line
Inhibition device Controlled line RFL = 3,9 Kohm
Contact low pressure Controlled line RFL = 3,9 Kohm
External Power Supply External power supply for extinguishing, evacuation and actuators (24Vdc)
Outputs
Evacuation indicator Controlled line RFL = 3,9 Kohm
Activation with reverse polarity (24Vdc)
Electronic protection :
- 500mA if internal power supply.
- 1A if external power supply
Extinguishing actuators Controlled line RFL = 3,9 Kohm
Activation with reverse polarity.
Current limiter for pyroelectric actuators (1A per 2sec)
Electronic protection for solenoid actuators (24Vdc)
600mA if internal power supply
2A if external power supply
NOTA : If the internal power supply is used to command the evacuation indicator and the
extinguishing actuators, don‘t forget this internal power supply is limited to 950mA by Electronic
protection.
Type of Actuators and Type of command

Type of command
Type of actuators
Internal Power supply External Power supply
24V per 30s 24V per 30s
Solenoid
Imax = 600mA Imax = 2A
Pyroelectric 1A per 2s 1A per 2s
Panel Page : 21/34
APPENDIX
Mechanical drawing
Product equipment
370mm (depth 118mm)
Battery 12V Relay card Battery 12V
Main card
Optional card Optional card 300mm

or blind plate or blind plate
or
blind plate
Card connectors
230VAC
General connecting area
Anticipate a free area of 150mm around the cabinet
Wall mounting
28mm
3 holes Ø 6 mm
300mm
28mm
115 mm 115 mm
Panel Page : 22/34
Mains connecting plan

Neutral Earth Phase
Mains Terminal Block
Cable clamp
Panel Page : 23/34
Panel connecting plan

Panel Page : 24/34
Detector and Sounders connection plan
Automatic detectors
SR95
Contact NO 60V/0,2A
S95
Shield
Shield
LTR
LTR
Type A : Basic connection Type D : Basic connection with relay
S95
Shield GENERAL REMARKS

1 Recommendation : All cable
LTR screens are protected by
spaghetti tubing.
2 All types (A to D) can be

mixed together
3 LTR : Line Terminal Resistor

Type B : With individual indicator
4 IA : Remote Indicator
S95
Shield
LTR
Type C : With common indicator

Panel Page : 25/34
Manual call points
BMY2
Shield protected by spaghetti
BMLY2
Shield protected by spaghetti
Sounders line
LTR
Panel Page : 26/34
Extinguishing configuration and connecting plan

Panel Page : 27/34
Input lines connection
Ract Ract
1KΩ 1KΩ
1/4W Reol
Manual Extinguishing 1/4W 3,9KΩ
Input 1/4W
Ract Ract
1KΩ 1KΩ
1/4W Reol
Extinction/Inhibition 1/4W 3,9KΩ
Input 1/4W
Ract
1KΩ Reol
Low Pressure input 1/4W 3,9KΩ
1/4W
Panel Page : 28/34
Output connection
Connection For Electromagnetic actuators
1N5406 1N5406
Extinguishing actuators
Type Electromagnetic Reol
24 Vdc for 30 s 3,9KΩ
2A maximum 1/4W
1N4004 1N4004
-
Electromagnetic actuator
Connection For Pyroelectric actuators
Extinguishing Pyroelectric actuator

actuators Reol
Type Pyroelectric 3,9KΩ
1N5406
1A maximum for 2s 1/4W
Connection For Extinguishing Indicators
Extinguishing indicators 24Vdc 1N4004 1N4004

500mA maximum with internal
supply* Reol
1A maximum with external supply 3,9KΩ
Indicator Indicator 1/4W
*Using panel power supply, the sum of

current required by the extinguishing
indicator, by extinguishing actuators, by
sounders output and by the load connected
on 24Vdc output must be lesser than 950
mA.
Panel Page : 29/34
Checklist Commissioning
This is a brief instruction. For detailed information refer to the corresponding chapter in the manual.
1. If needed, mount the optional card(s).Make sure that the jumper ST1 at the left card is installed
and the jumper ST1 at the right card is removed.
2. All the detector lines must have an end resistor of 3kΩ (2850Ω ...3150Ω).
Check this value by means of a multimeter
3. The sounders line and the input of ALPHA4/8/12 must have an end resistor of 3k9Ω. If
extinguishing card is used, all input lines and output lines must have an end resistor of 3k9Ω.
Check this value by means of a multimeter
4. Connect the mains (230VAC) to the panel.

The LED «System Fault» will light up for a short moment (during initialisation of the panel)
The LED «Fault/Off» of every line is on.
5. Put the 2 batteries in the box. Connect the bridge from bat.1 «+» to bat.2 «-».
Connect the battery cables from the panel to bat.1 «-» and to bat.2 «+».
6. Enter access level2

- Press «A» and «B» simultaneously. The LED «Access level 2 or 3» starts to blink.
- Now press A,B,A,B successively, then AB simultaneously. Now the LED lights steady.
Rem.: Exit level 2 by pressing AB simultaneously or automatically after a timeout of 2 min.
7. Enable all detection lines. Press «Fault/Off» of each line.

Caution: from now on, the panel is active. In case of alarms, the output will be activated.
8. Make the required software settings. When you are in access level 2, use the following code.
Rem.: By default, all the lines are associated to the alarm zone.
Code Key Function

BABA, «AB» «Disable(test)» of each line 1 or 2 detector alarm
«On/Off» sounders Disable / enable sounders
ABBB, «AB» «On/Off» sounders Alarm zone AZ
«Disable(test)» of each line Join / not join the AZ
BAAA, «AB» «On/Off» sounders Delay time of the sounders
«A» Decrease delay time
«B» Increase delay time
AAAA, «AB» «A» Simple level 2 access
«B» Standard level 2 access
BBBB, «AB» See list in manual Programming open collector output (O.C)
AABB, «AB» See list in manual Programming input
Extinguishing module software settings :

Rem : The line (minimum 2 lines) must be associated to the extinguishing zone to allow the
extinguishing activation.
Code Key Function

ABBB, «AB» Extinguishing key Test/off «On/Off». Extinguishing zone EZ
«Disable(test)» of each line Join / not join the EZ
BAAA, «AB» Extinguishing key Manual/Automatic Delay time of the Extinguishing
«On/Off» activation
Extinguishing key Test/off «On/Off» Decrease or Increase delay time
9. Make the necessary tests.
Panel Page : 30/34
User Maintenance / System Inspection

It states the responsibility to carry out all routine tests and maintenance rests with the owner/ manager
of property in which the fire alarm system is installed. The following tests are advised.
WARNING !
Before effecting any control disconnect the extinguishing actuators if it is

used.
DAILY INSPECTION
Check that the System Energised LED is lit.
Check no other LEDS are lit and that no sounders are operating.
Report any faults to the designated site maintenance engineer.
WEEKLY TEST
Press the Led/Buzzer Test to check that all LEDs lights show and the warning beeper sounds.
Switch off the mains supply and verify the fault signalling are given.
Stop the beeper sounds.
Switch on again the mains supply.
MONTHLY TEST
One Fire Detector Point or one Manual Call Point have to be tested to check the system can operate
in case of Fire. During each control, Test a different zone each week and always use a different call
point or smoke/heat detector for each test so that all devices are tested in rotation.
Check that the alarm sounders operate.
QUARTERLY TEST
Visually inspect the battery and it’s connections. Please note : Lethal voltages are present inside
the panel . Do not open the panel unless you are qualified to do so and DO NOT touch the
power supply unit.
Operate a call point or sensor in each zone to test the fire alarm as in the monthly test above.
Remove the mains supply and check that the battery is capable of supplying the alarm sounders.
ANNUAL TEST :
As for the monthly and quarterly test but check every detector, call point, sounder, and all auxiliary
equipment for correct operation.
EVERY 2 to 3 YEARS :
Clean the smoke/ heat detector s to ensure the correct operation and freedom from false alarms.
SERVICING :
REGULAR SERVICING IS HIGHLY RECOMMENDED, preferably on a continuous maintenance
contract and by a competent organisation. A full-itemised report of the installation should be obtained
at least annually.
Panel Page : 31/34
12 relay card configuration and connecting plan
ST1 ST2 ST3 ST4 ST5 ST6 ST7 ST8 ST9 ST10 ST11 ST12
S1 S3 S5 S7 S9 S11
ON ON ON ON ON ON
S2 S4 S6 S8 S10 S12
1 1 1 1
K1 K4 K7 K10
2 2 2 2
3 3 3 3
B1 K2 B2 K5 B3 K8 B4 K11
4 4 4 4
5 5 5 5
6
K3 6
K6 6
K9 6
K12
J2
J1
Switches S1, S2, …, S12:

select normally open (N.O) or normally closed (N.C) relay’s contact on terminal blocks.
ON position = N.O
OFF position = N.C
Jumpers ST1, ST2… ST12:

Allow to insert of a 560 ohm resistor in series to the contact. If the jumper is present, the resistor is
short circuited and then the contact is clean
removed = 560 Ohm
set position= 0 Ohm
Terminal J1: Connexion via flat cable to ALPHA 4/8/12 (J5)
Terminal J2: not used
Terminal blocks
B1 B2 B3 B4
B1.1 COM Relay B2.1 COM Relay B3.1 COM Relay B4.1 COM Relay
B1.2 N.O./N.C. K1 B2.2 N.O./N.C. K4 B3.2 N.O./N.C. K7 B4.2 N.O./N.C. K10
Panel Page : 32/34
Contact association
Terminal Relay Module ALPHA 4-8-12

B1.1-1.2 1 Main Fire alarm line 1*
B1.3-1.4 2 Fire alarm line 2*
EX4A4 DEAG
B2.3-2.4 5 Extension card at Fire alarm line 5* Extinguishing actuators ch.1 active
B2.5-2.6 6 left position ST1 Fire alarm line 6* Channel 1 in evacuation status
B3.1-3.2 7 set Fire alarm line 7* Channel 1 in inhibition status
B3.3-3.4 8 Fire alarm line 8* Channel 1 in manual mode
EX4A4 DEAG
B3.5-3.6 9 Extension card at Fire alarm line 9* Extinguishing actuators ch. 2 active
B4.1-4.2 10 right position ST1 Fire alarm line 10* Channel 2 in evacuation status
B4.3-4.4 11 removed Fire alarm line 11* Channel 2 in inhibition status
B4.5-4.6 12 Fire alarm line 12* Channel 2 in manual mode
* association of the fire alarm lines see drawing below
Association of fire alarm lines

Panel Page : 33/34
Operation instructions of Extinguishing module
Red Steady
At least a detection line associated
with the extinguishing channel is in
alarm.
Red Steady Yellow Steady
Extinguishing cycle (delay) in Extinguishing channel is disabled
progress. At least two detection Blinking con T=2s.
lines associated with the Extinguishing channel is in test
extinguishing channel is in alarm. mode
Red Steady
Discharge actuators are activated. Help the user to detect the
functions of the extinguishing
channel in fault status.
Yellow Steady.
Yellow Steady
Discharge command is inhibited
A function of the extinguishing
thanks to the inhibition input line.
channel is in fault
Yellow Blinking T=1s.
Yellow Steady
More then one function of the
The automatic mode is off.
extinguishing channel is in fault
Yellow Steady
The manual mode is off
Faults code identification
Type of fault LED A LED B LED C

No fault OFF OFF OFF
Extinguishing actuators line OFF OFF ON
Evacuation indicator line OFF ON OFF
Extinguishing MCP line OFF ON ON
Inhibition (aut/man) line ON OFF OFF
Contact low pressure line ON OFF ON
External Power supply not connected ON ON OFF
Low pressure ON ON ON
Installation Manual Document :01 NGP 1145
ALPHA 4/8/12 Index :B
Conventional Fire Alarm Control Panel Date : 14/01/04
Page : 34/34
Operation instructions
LED on: LED on: Sounders function:

At least one power source is on 2 detectors alarm mode is active. Press the This function allows the activation of the sounders. The manual command allows to switch off then activate the sounders again
(230V or battery) push button On/Off below to after an automatic command. It is possible to delay this activation. In this case, it is possible to stop the alarm process by
activate/deactivate this mode. pressing the button « Silence Buzzer » at level 2 access during 3 seconds.
LED blinking and Buzzer continuous:

Fault/ Indicates a fault on the sounders line.
LED on and buzzer intermittent:
Zone warning Zone LED on:
One fire alarm is present on the system. Power
LED blinking: n° : n° : Sounders line is disabled. This condition is
Evacuate
One detector is active when the system is in 2 programmed at access level 3.
detectors alarm mode (pre-alarm mode). FIRE ALARM
If another detector of the same zone is active O N/OFF
Fire alarm Fire alarm
the system releases a fire alarm. Fault warning LEVEL 2 LED on and Buzzer continuous:
Alarm is active (evacuation in progress).
LED on and Buzzer continuous: Fault/ Disabled Fault/ It is possible to stop or activate the sounders at
At least one fault or anomaly has occurred. disabled/ disabled/ access level 2 by pressing the push button «
test test
T
Test day/night On/Off » successively.

LED blinking and Buzzer intermittent:
LED on: Disable Level Disable Level Alarm delay time is running.
2 System fault Active 2
Zones of the panel are disabled (test) (test)
or in test mode. During the delay mode,
Power supply fault ON/OFF
- the sounders can be activated immediately by
LED on: LEVEL 2 pressing the button « On/Off ».
The system is in fault - the alarm process can be stopped by
(software failure or fault communication pressing « silence buzzer » at level 2 access
Access level 2 or 3 during 3 seconds.
between main card and extension card). Zone Zone
n° : n° :
A B
LED on: Control field of fire detection zone «DZ »:
Mains failure (230V) Each detection zone is associated to a control
LED blinking: Fire alarm Fire alarm field with two indicators and one push button.
Battery fault. Each control field is associated to an identified
In case of mains failure, the system is Fault/ Fault/ installation area
operating a period of at least 24 hours. disabled/ disabled/
LED on and Buzzer intermittent:
test Led – Silence Reset
test Fire alarm in the zone.
LED + 2 access keys A, B (level 1 access): buzzer buzzer Panel LED blinking:
test One detector is active.
Code management for accessing level 2 or 3 Disable Level Level 2 Disable Level
(see chapter configuration). The zone is in 2 detectors mode (pre-alarm
(test) 2 (test) 2
mode)
It is used to change system parameters.
LED on:
Key Test Led/Buzzer (level 1 access): The zone is disabled.
Activates the buzzer and all LEDs at the panel Key Silence Buzzer (level 1 access): Key Reset Panel (Level 2 access): Key Disable (level 2 access): LED blinking fast and Buzzer continuous:
incl. extension cards for test purpose. Allows at any time the internal buzzer signal to After the cause of the alarm has been Allows to enable/disable the The line is in fault (open circuit, short circuit,
At level 2 access, this key is used to enter in be switched off temporary; it then remains eliminated, this key allows the panel to zone or to enter the zone in detector fault or removed detector)
test mode. available for any further information. be reset. test mode. LED slow blinking:
Caution: During the delay mode, the alarm It is also used to exit from test mode. (For test mode, at first press The zone is in test mode. This indication has
process can be stopped by pressing « Silence the key Test Led/Buzzer). less priority than the others.
Buzzer » at level 2 access during 3 seconds.

Alpha 4-8-12

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Alpha 4-8-12

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Alpha 4-8-12

Uploaded by

Copyright:

Available Formats

Installation Manual Document : 01 NGP 1145

ALPHA 4/8/12 GBR Index :B

Conventional fire alarm panel

The document includes instructions about

In addition to this document, these following items are necessary:

The operation access to the panel is divided on 3 levels

Level 1 direct access for all personnel (no code).

Level 3 protected access for installer (by digital code).

Part Line type Wire type

Line resistance «LR»

Rating resistance «RR»

Insulation resistance «IR»

• Check the correct mains voltage (between 195VAC and 253VAC)

Before any intervention it is indispensable to make sure that all parts

Level 2 and 3 access general mode

The standard level 2 access:

1) The simple level 2 access:

After a timeout of 2 minutes, the access level 2 will be deactivated automatically

FUNCTIONS For the fire detection cards:

Enable/disable the test mode of detection zones and/or extinguishing channel

• Press the key « LEVEL 2 » of the function « DISABLE (TEST) » of

Enable / disable sound broadcasters line

Alarm zone and detection zone association

2) Allows to check the association « AZ/DZ »

Extinguishing zone and detection zone association

FUNCTIONS 1) Allows to associate two (minimum to activate the extinguishing zone) or

2) Allows to check the association « EZ/DZ »

2) Allows to check the delay.

The main card displays the programmed delay as follows :

2) Allows to check the delay.

FUNCTIONS 1) Allows to modify or to check the access code level 2

Standard access code level 2

Standard delay (only for the 4 zones of the main card):

Validation and exit:

Setting of the 4 open collector outputs

FUNCTIONS Allows to charge an event to each of the 4 open collector outputs.

Function of the input

FUNCTIONS Allows to charge an event to the input.

Validation and Exit

CONTROLS AND TESTS

Before effecting any control the extinguishing actuators have to disconnect if it

Test power supply

Control Action Result

Fire detection lines

Electrical and mechanical characteristics

Admissible weighting on one detector line 35 u

Electrical characteristics of extinguishing card

Type of Actuators and Type of command

370mm (depth 118mm)

Battery 12V Relay card Battery 12V

Optional card Optional card 300mm

Anticipate a free area of 150mm around the cabinet

Mains connecting plan

Mains Terminal Block

Panel connecting plan

Detector and Sounders connection plan

Type A : Basic connection Type D : Basic connection with relay

Shield GENERAL REMARKS