DI−93

DIAGNOSTICS − ENGINE
DI5PP−02

DTC P0510 Closed Throttle Position Switch Malfunction

CIRCUIT DESCRIPTION
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page DI−35.
DTC No. DTC Detecting Condition Trouble Area
The closed throttle position switch does not turn ON or OFF S Open or short in closed throttle position switch circuit
P0510 even once when the vehicle is driven S Closed throttle position switch
(2 trip detection logic) S ECM

HINT:
After confirming DTC P0510 use the TOYOTA hand−held tester to confirm the closed throttle position switch
signal from ”CURRENT DATA”.
Throttle Valve Closed Throttle Position Switch Signal Malfunction
Fully closed OFF Open circuit
Fully open ON Short circuit

WIRING DIAGRAM
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page DI−35 for WIR-
ING DIAGRAM.

INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) are output simultaneously, E2 (Sen-
sor Ground) may be open.

TOYOTA hand−held tester

1 Connect the TOYOTA hand−held tester and read CTP switch signal.

PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand−held tester.
RESULT:
Throttle Valve Closed Throttle Position Switch Signal Malfunction
Fully closed OFF Open circuit: Go to step 2
Fully open ON Short circuit: Go to step 4

1996 LAND CRUISER (RM451U)

DI−94
DIAGNOSTICS − ENGINE

2 Check for open in harness or ECM.

ON PREPARATION:
(a) Disconnect throttle position sensor connector.
Throttle Position
(b) Connect sensor wire harness terminals between
Sensor ECM
4 1 5V terminals 1 and 2.
VCC
E5
12V
(c) Turn ignition switch ON.
3 10 VTA
E5 CHECK:
2 11
E5
IDL
Read CTP switch signal on TOYOTA hand−held tester.
1 9 E2
E5
E1 OK:
BE6653
FI7058 A00486 CTP switch signal: ON

OK Confirm good connection at sensor.

If OK, replace throttle position sensor.

NG

3 Check for open in harness or ECM.

PREPARATION:
ON
(a) Remove instrument panel speaker No.1 panel
Throttle Position Sensor ECM (See page SF−65).
4 1 5V
E5
VCC
(b) Connect between terminals IDL and E2 of ECM.
12V HINT:
3 10 VTA
E5
2 11 IDL Throttle position sensor connector is disconnected.
E5
1 9 E2
E5
Before checking, do a visual check and contact pressure check
E1
for connector (See page IN−28).
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand−held tester.
OK:
IDL E2 CTP switch signal: ON
FI7064
A00487

OK Open in harness between ECM and throttle

position sensor, repair or replace harness.

NG

Confirm connection at ECM.

If OK, replace ECM (See page IN−28).

1996 LAND CRUISER (RM451U)

 DI−95
DIAGNOSTICS − ENGINE

4 Check for short in harness or ECM.

PREPARATION:
ON
(a) Disconnect throttle position sensor connector.
Throttle Position Sensor ECM (b) Turn ignition switch ON.
4 1 VCC 5V
E5 CHECK:
12V
3 10 VTA
E5
Read CTP switch signal on TOYOTA hand−held tester.
2 11 IDL1
E5 OK:
1 9
E5 E2 CTP switch signal: OFF
E1

BE6653
A00499 A00488

OK Confirm good connection at sensor.

If OK, replace throttle position sensor.

NG

5 Check for short in harness or ECM.

ON
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
Throttle Position (See page SF−65).
Sensor ECM (b) Disconnect E5 connector of ECM.
4 1 VCC 5V
E5
HINT:
12V
3 10 VTA1
E5 Throttle position sensor connector is disconnected.
2 11 IDL1
E5 (c) Turn ignition switch ON.
1 9 E2
E5
CHECK:
Read CTP switch signal on TOYOTA hand−held tester.
OK:
CTP switch signal: OFF

BE6653
E5 Connector
A00498
A00496 A00489

OK Short in harness between ECM and throttle

position sensor, repair or replace harness.

NG

Confirm connection at ECM.

If OK, replace ECM (See page IN−28).

1996 LAND CRUISER (RM451U)

DI−96
DIAGNOSTICS − ENGINE

OBD II scan tool (excluding TOYOTA hand−held tester)

1 Check for open and short in harness or ECM.

ON
PREPARATION:
(a) Disconnect throttle position sensor connector.
Throttle Position Sensor ECM (b) Turn ignition switch ON.
4 1 5V
E5 VCC CHECK:
10 12V Measure voltage between terminals 1 and 2 of throttle position
3 VTA
E5

2 11
IDL
sensor connector.
E5

1 9
E5
E2 OK:
E1 Voltage: 9 − 14 V
A00492

OK Confirm good connection at sensor.

If OK, replace throttle position sensor.

NG

2 Check for open and short in harness and connector between throttle position
sensor and ECM (See page IN−28).

NG Open or short in harness between ECM and

throttle position sensor.

OK

Confirm connection at ECM.

If OK, replace ECM (See page IN−28).

1996 LAND CRUISER (RM451U)