Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Tsop 772 W

Download as pdf or txt
Download as pdf or txt
You are on page 1of 13

Datasheet Values Refer to PCN-OPT-1224-2022

TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems

DESCRIPTION
This IR receiver series is optimized for long burst remote
control systems in different environments. The customer
can chose between different IC settings (AGC variants), to
find the optimum solution for his application. The higher the
AGC, the better noise is suppressed, but the lower the code
compatibility.
The devices contain a PIN diode and a preamplifier
assembled on a lead frame. The epoxy package contains an
IR filter. The demodulated output signal can be directly
connected to a microprocessor for decoding. These
components have not been qualified to automotive
specifications.

FEATURES
• Individual IC settings to reach maximum
performance
• Immunity against noise (lamps, LCD TV, Wi-Fi)
21589
• Low supply current
• Photo detector and preamplifier in one package
• Supply voltage: 2.0 V to 5.5 V
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912

LINKS TO ADDITIONAL RESOURCES APPLICATIONS


• Infrared remote control systems
Product Page Marking

DESIGN SUPPORT TOOLS


• 3D models
• Window size calculator

BLOCK DIAGRAM
2
VS
30 k Ω
3
Band Demo- OUT
Input AGC
pass dulator
1, 4
PIN Control circuit GND

20445-1

Rev. 2.2, 19-Aug-2022 1 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
MECHANICAL DATA ORDERING CODE
Pinning: Taping:
1, 4 = GND, 2 = VS, 3 = OUT TSOP77...WTT - top view taped, 2200 pcs/reel
TSOP77...WTR - side view taped, 2300 pcs/reel

APPLICATION CIRCUIT
17170-14
R1
Transmitter IR receiver
with VS + VS
1 TSALxxxx
C1

Circuit
2
µC
3 OUT
23208 4 VO
GND GND

R1 and C1 recommended in case there are strong ripple or


spikes on the supply line.

PARTS TABLE
LEGACY, FOR RECOMMENDED FOR
AGC
LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) (1)
30 kHz TSOP77230W TSOP77430W
33 kHz TSOP77233W TSOP77433W
Carrier 36 kHz TSOP77236W TSOP77436W (2)(3)(4)
frequency 38 kHz TSOP77238W TSOP77438W (5)(6)(9)(11)
40 kHz TSOP77240W (12) TSOP77440W
56 kHz TSOP77256W (10) TSOP77456W (7)(8)
Package Heimdall no lens
Pinning 1, 4 = GND, 2 = VS, 3 = OUT
Dimensions (mm) 6.8 W x 3.0 H x 2.35 D
Mounting SMD
Application Remote control
(2) RC-5 (3) RC-6 (4) Panasonic (5) NEC (6) Sharp (7) r-step (8) Thomson RCA
Best choice for (9) Sejin 4PPM (10) Cisco (11) Mitsubishi (12) Sony

• Extended temperature range: www.vishay.com/doc?82738


Special options • Narrow optical filter: www.vishay.com/doc?81590
• Wide optical flter: www.vishay.com/doc?82726
Note
(1) We advise try AGC4 first if the burst length is unknown

Rev. 2.2, 19-Aug-2022 2 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors

ABSOLUTE MAXIMUM RATINGS


PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage VS -0.3 to +6 V
Supply current IS 5 mA
Output voltage VO -0.3 to 5.5 V
Voltage at output to supply VS - VO -0.3 to (VS + 0.3) V
Output current IO 5 mA
Junction temperature Tj 100 °C
Storage temperature range Tstg -25 to +85 °C
Operating temperature range Tamb -25 to +85 °C
Power consumption Tamb ≤ 85 °C Ptot 10 mW
Soldering temperature t ≤ 10 s, 1 mm from case Tsd 260 °C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)


PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply voltage VS 2.0 - 5.5 V
VS = 3.3 V, Ev = 0 ISD 0.25 0.35 0.45 mA
Supply current
Ev = 40 klx, sunlight ISH - 0.8 - mA
Ev = 0, IR diode TSAL6200, IF = 50 mA,
Transmission distance d - 12 - m
test signal see Fig. 1
Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV
Test signal: RC5 code Ee min. - 0.4 0.8 mW/m2
Minimum irradiance
Test signal: NEC code Ee min. - 0.6 1.0 mW/m2
Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee max. 50 - - W/m2
Directivity Angle of half transmission distance ϕ1/2 - ± 75 - °

TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

Axis Title
Ee Optical Test Signal 1.0 10000
(IR diode TSAL6200, 30 pulses, f = f0, T = 10 ms)
0.9 Output pulse width
tpo - Output Pulse Width (ms)

0.8
0.7 Input burst length
t 1000
0.6
tpi (1)
2nd line
1st line
2nd line

0.5
T
(1)
tpi ≥ 10/f0 0.4
Output Signal 100
VO 16110-12 0.3
(2)
7/f0 < td < 13/f0
(3) 0.2
VOH tpi - 4/f0 < tpo < tpi + 4/f0 λ = 950 nm,
0.1 optical test signal, Fig. 1

VOL 0.0 10
td (2) tpo (3) t 0.1 10 1000 100 000
Ee - Irradiance (mW/m2)

Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient

Rev. 2.2, 19-Aug-2022 3 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors

Optical Test Signal Axis Title


Ee 4 10000
Correlation with ambient light sources:

Ee min. - Threshold Irradiance (mW/m2)


10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K)
10 W/m2 = 8.2 klx (daylight, T = 5900 K)
3
Wavelength of ambient 1000
t illumination: λ = 950 nm
600 µs 600 µs

2nd line
1st line
2nd line
2
t = 60 ms
94 8134 100
Output Signal, (see Fig. 4)
VO 1

VOH

0 10
VOL
0.01 0.1 1 10 100
t on t off t
Ee - Ambient DC Irradiance (W/m2)

Fig. 3 - Output Function Fig. 6 - Sensitivity in Bright Ambient

Axis Title Axis Title


0.8 10000 0.8 10000

0.7 ton Ee min. - Threshold Irradiance (mW/m2)


ton, toff - Output Pulse Width (ms)

0.7
0.6
1000 1000
0.5 f = f0
toff 0.6
2nd line

2nd line
1st line

1st line
2nd line

2nd line

f = 30 kHz
0.4
f = 10 kHz
0.3 0.5 f = 100 Hz
100 100
0.2
0.4
0.1 λ = 950 nm,
optical test signal, Fig. 3
0 10 0.3 10
0.1 1 10 100 1000 10 000 1 10 100 1000
Ee - Irradiance (mW/m2) ∆VS RMS - AC Voltage on DC Supply Voltage (mV)

Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances

Axis Title
1.2 1.0 10000
f = 38 kHz, Ee = 2 mW/m2
Ee min./Ee - Relative Responsivity

0.9
1.0
Maximum Envelope Duty Cycle

0.8
0.8 0.7
1000
AGC 2
0.6
2nd line
1st line
2nd line

0.6
0.5
0.4 0.4
100
f = f0 ± 5 % 0.3
0.2
Δf(3 dB) = f0/10 0.2 AGC 4

0.0 0.1
0.7 0.9 1.1 1.3 0 10
16925 f/f0 - Relative Frequency 0 20 40 60 80 100 120 140
Burst Length (Number of Cycles/Burst)

Fig. 5 - Frequency Dependence of Responsivity Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length

Rev. 2.2, 19-Aug-2022 4 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors

Axis Title
0° 10° 20° 30°
0.8 10000
Ee min. - Threshold Irradiance (mW/m2)

0.7 40°

0.6 1000
50°

2nd line
1st line
2nd line

1.0
0.5

0.9 60°
0.4 100
70°
0.8
0.3 80°

0.6 0.4 0.2 0


0.2 10
-30 -10 10 30 50 70 90 22194 drel - Relative Transmission Distance
Tamb - Ambient Temperature (°C)

Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Vertical Directivity

Axis Title Axis Title


1.0 10000 0.8 10000
0.9 Ee min. - Threshold Irradiance (mW/m2)
S(λ)rel. - Relative Spectral Sensitivity

0.7
0.8
0.7
1000 0.6 1000
0.6
2nd line

2nd line
2nd line

1st line
1st line
2nd line

0.5 0.5
0.4
100 0.4 100
0.3
0.2
0.3
0.1
0 10 0.2 10
750 850 950 1050 1150 1 2 3 4 5 6
21425 λ - Wavelength (nm) VS - Supply Voltage (V)

Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Fig. 13 - Sensitivity vs. Supply Voltage

0° 10° 20° 30°

40°

1.0

0.9 50°

0.8 60°

70°
80°

0.6 0.4 0.2 0

22193 drel - Relative Transmission Distance

Fig. 11 - Horizontal Directivity

Rev. 2.2, 19-Aug-2022 5 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
This series is designed to suppress spurious output pulses Axis Title
7 10000
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in 6
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center 5

IR Signal Amplitude
1000
frequency (e.g. 38 kHz) and fulfill the conditions in the table

2nd line
below. 4

1st line
2nd line
When a data signal is applied to the product in the presence 3
of a disturbance, the sensitivity of the receiver is
100
automatically reduced by the AGC to insure that no spurious 2
pulses are present at the receiver’s output.
1
Some examples which are suppressed are:
• DC light (e.g. from tungsten bulbs sunlight) 0 10
• Continuous signals at any frequency 0 5 10 15 20
16920 Time (ms)
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 14 or Fig. 15) Fig. 14 - IR Disturbance from Fluorescent Lamp
With Low Modulation
• 2.4 GHz and 5 GHz Wi-Fi

Axis Title
40 10000

20
IR Signal Amplitude

1000
0

2nd line
2nd line

1st line
-20
100

-40

-60 10
0 5 10 15 20
16921 Time (ms)

Fig. 15 - IR Disturbance from Fluorescent Lamp


With High Modulation

TSOP772..W TSOP774..W
Minimum burst length 10 cycles/burst 10 cycles/burst
After each burst of length 10 to 72 cycles 10 to 40 cycles
a minimum gap time is required of ≥ 10 cycles ≥ 10 cycles
For bursts greater than 72 cycles 40 cycles
a minimum gap time in the data stream is needed of > 3 x burst length > 10 x burst length
Maximum number of continuous short bursts/second 950 1500
NEC code Yes Preferred
RC5 / RC6 code Yes Preferred
Thomson 56 kHz code Yes Preferred
Sharp code Yes Preferred
Complex and critical disturbance
Mild disturbance patterns
patterns are suppressed (example:
Suppression of interference from fluorescent lamps are suppressed (example:
signal pattern of Fig. 15 or
signal pattern of Fig. 14)
highly dimmed LCDs)
Notes
• For data formats with short bursts please see the datasheet of TSOP773..W and TSOP775..W

Rev. 2.2, 19-Aug-2022 6 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
6.8
6.6 ± 0.1
Center of
(3.25) sensitive area
Mold residue 2.35
Mold residue

0.8
3

1.2 ± 0.2
(1.8)
(0.635) (1)
1.27
(3 x)
0.5 ± 0.1
(4 x)
technical drawings
3 x 1.27 = 3.81
according to DIN
specifications
Marking area

(2.2) Not indicated tolerances ± 0.15


Tool separation line

Proposed pad layout


from component side
2.05

(for reference only)


(1.5)

3 x 1.27 = 3.81

1.27

Pick and place area


1.8

Drawing-No.: 6.550-5300.01-4
Issue: 4; 13.09.11

22609 0.8

ASSEMBLY INSTRUCTIONS
Reflow Soldering Manual Soldering
• Reflow soldering must be done within 72 h while stored • Use a soldering iron of 25 W or less. Adjust the
under a max. temperature of 30 °C, 60 % RH after temperature of the soldering iron below 300 °C
opening the dry pack envelope • Finish soldering within 3 s
• Set the furnace temperatures for pre-heating and heating • Handle products only after the temperature has cooled off
in accordance with the reflow temperature profile as
shown in the diagram. Exercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handling after reflow should be done only after the work
surface has been cooled off

Rev. 2.2, 19-Aug-2022 7 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
Axis Title
300 10000
max. 260 °C
250 255 °C
240 °C 245 °C
217 °C

Temperature (°C)
200 1000
max. 20 s

2nd line

2nd line
1st line
150
max. 120 s max. 100 s
100 100

Max. ramp up 3 °C/s Max. ramp down 6 °C/s


50

Max. 2 cycles allowed


0 10
0 50 100 150 200 250 300
19800 Time (s)

TAPING VERSION TSOP..TR DIMENSIONS in millimeters


0.3

3.6

16

1.75 7.5

Ø 1.5

Ø 1.5
2
8

Direction of feed
4

technical drawings
Drawing-No.: 9.700-5342.01-4 according to DIN
Issue: 2; 12.06.13 specifications

Rev. 2.2, 19-Aug-2022 8 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
TAPING VERSION TSOP..TT DIMENSIONS in millimeters

0.3

3
16

1.75 7.5

Ø 1.5

Ø 1.5 min.
2
8

Direction of feed
4

technical drawings
Drawing-No.: 9.700-5341.01-4 according to DIN
Issue: 3; 06.10.15 specifications

Rev. 2.2, 19-Aug-2022 9 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
REEL DIMENSIONS in millimeters

16734

LEADER AND TRAILER DIMENSIONS in millimeters


Trailer Leader

no devices devices no devices

End Start

min. 200 min. 400


96 11818

COVER TAPE PEEL STRENGTH


According to DIN EN 60286-3
0.1 N to 1.3 N
300 ± 10 mm/min.
165° to 180° peel angle

Rev. 2.2, 19-Aug-2022 10 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
OUTER PACKAGING

The sealed reel is packed into a pizza box.

CARTON BOX DIMENSIONS in millimeters

Length
Thickness

Width
22127

THICKNESS WIDTH LENGTH


Pizza box (SMD and heimdall)
50 340 340
(taping in reels)

LABEL

Standard bar code labels for finished goods

The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final
packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to
warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data.

VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING ABBREVIATION LENGTH
Item-description - 18
Item-number INO 8
Selection-code SEL 3
LOT-/serial-number BATCH 10
Data-code COD 3 (YWW)
Plant-code PTC 2
Quantity QTY 8
Accepted by ACC -
Packed by PCK -
Mixed code indicator MIXED CODE -
Origin xxxxxxx+ Company logo
LONG BAR CODE TOP TYPE LENGTH
Item-number N 8
Plant-code N 2
Sequence-number X 3
Quantity N 8
Total length - 21
SHORT BAR CODE BOTTOM TYPE LENGTH
Selection-code X 3
Data-code N 3
Batch-number X 10
Filter - 1
Total length - 17

Rev. 2.2, 19-Aug-2022 11 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP772..W, TSOP774..W
www.vishay.com
Vishay Semiconductors
DRY PACKING ESD PRECAUTION
The reel is packed in an anti-humidity bag to protect the Proper storage and handling procedures should be followed
devices from absorbing moisture during transportation and to prevent ESD damage to the devices especially when they
storage. are removed from the antistatic shielding bag. Electrostatic
Aluminum bag sensitive devices warning labels are on the packaging.

Label VISHAY SEMICONDUTORS STANDARD


BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
Reel data.

15973
BAR CODE PRODUCT LABEL (example)
FINAL PACKING
The sealed reel is packed into a cardboard box.

RECOMMENDED METHOD OF STORAGE


Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
22178
not available:
• Storage temperature 10 °C to 30 °C
• Storage humidity ≤ 60 % RH max.
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air /
nitrogen) or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC® standard J-STD-020 level 4 label is included
on all dry bags.

LEVEL
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES 4
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative
humidity (RH)
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or
2b. Stored at < 5 % RH
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or
2a. or 2b. are not met.
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or
24 hours at 125 °C ± 5 °C not suitable for reels or tubes
Bag Seal Date:
(If blank, see barcode label)

Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020

22522

EIA JEDEC standard J-STD-020 level 4 label is included


on all dry bags

Rev. 2.2, 19-Aug-2022 12 Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.

Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

© 2024 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED

Revision: 01-Jan-2024 1 Document Number: 91000


For technical questions, contact:
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

You might also like