Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 3 views

    MI_TR 420_EN

    Uploaded by

    Samuele Zini

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MI_TR 420_EN

    Uploaded by

    Samuele Zini
    3 views8 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3 views8 pages

    MI_TR 420_EN

    Uploaded by

    Samuele Zini

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 8

    1 Note!

    Before installing this product, check the contents of


    the kit. If anything is missing, please check an Öhlins
    dealer.

    Kit Contents
    Description Part No Pcs
    Shock absorber TR 420 1
    C-spanner S46 60710-02 1
    Sticker set "ÖHLINS" 10207-01 1
    Owners manual 07241-02 1

    1 Note!
    Please note that this image is a general representation
    of the product and may differ slightly from your product.

    1 Note!
    Please note that during storage and transportation,
    especially at high ambient temperature, some of the oil ⚠ Warning!
    and grease used for assembling may leak and stain the Before installing this product, read the Öhlins Owner’s
    packaging. This is in no way detrimental to the product, Manual. The shock absorber is an important part of your
    wipe off the excessive oil/grease with a cloth. vehicle and will affect the stability.

    Shock Absorber for Triumph Scrambler 400 X

    TR 420
    Mounting Instructions
    MOUNTING INSTRUCTIONS

    ⚠ Warning! 1 Note!
    It is advisable to have an Öhlins dealer install the shock Before mounting this product clean the vehicle
    absorber. thoroughly.

    ⚠ Warning! 1 Note!
    If working on a raised vehicle, ensure it is securely When working on this product, always see the Vehicle
    supported so that it will not tip over. Service Manual for vehicle specific procedures and
    important data.

    1.
    Put the motorcycle on a work stand so that the
    rear wheel barely touches the ground. Make sure
    the motorcycle is in a stable position.

    2.
    Remove the passenger seat Ⓐ by using the
    ignition key.

    A
    B

    2
    MOUNTING INSTRUCTIONS

    3.
    Remove the rider seat Ⓑ by loosening the
    screws ①②

    A
    B

    1 2

    4.
    4.1 Loosen the screw ③ in order to remove
    the coverⒸ on left side from the motorcycle.

    4.2 Loosen the screw ④ in order to remove


    the coverⒹ on left side from the motorcycle.
    3
    4
    C D

    3
    MOUNTING INSTRUCTIONS

    5.
    Remove the standard shock absorber by
    loosening the top mounting ①and the lower
    Direction of
    mounting bolts ②
    rebound adjuter

    6.
    Install the Öhlins shock absorber with the
    rebound adjuster pointing upwards.
    Tighten the upper ① and the lower mounting
    bolts ② at a torque value as specified in the
    vehicle service manual.

    7.
    Reverse all the procedure as necessary.

    1 Note!
    Lower the vehicle so that the suspension is slightly
    compressed before tightening the screws.

    ✋ Caution!
    Ensure that all screws are tightened to the correct
    torque and that nothing fouls or restricts movement
    of the shock absorber when the suspension is fully
    compressed or extended.

    4
    This page intentionally left blank
    This page intentionally left blank
    This page intentionally left blank
    ADJUSTMENTS
    ⚠ Warning! Rebound
    Before riding, always make sure that the basic settings
    Adjuster
    made by Öhlins are according to recommended
    Set-up Data. Read about adjustments and setting up
    in the Öhlins Owner’s Manual before you make any
    adjustments. Contact an Öhlins dealer if you have any
    questions about setting up.

    Spring Preload
    Adjuster

    Compression
    Adjuster

    SET-UP DATA
    Recommended set-up Shock absorber data
    Spring Preload............. 8 mm. Length ............................. 324.5 mm.
    Compression adjuster 16 Clicks Stroke .............................. 58 mm.
    Rebound adjuster ........ 16 Clicks
    Spring Installed spring
    Part No ................... 61095-49
    Free spring length... 180 mm.
    Spring rate.............. 130 N/mm
    Preload adj.range.... [0-22] mm

    Öhlins products are subject to To find the latest information Part no. MI_TR 420_EN_0
    continuous improvement and contact an Öhlins distributor. Issued 2024-07-31
    development, therefore, although Please contact Öhlins if you have
    these instructions include the most any questions regarding the
    up-to-date information available at contents in this document.
    the time of printing, minor updates
    may occur.

    © Öhlins Asia Co. Ltd. All rights Öhlins Asia Co. Ltd
    reserved. Any reprinting or 700/937 Moo5, Tambol Nongkhaga,
    unauthorized use without the written Amphur Phantong, Chonburi Province
    permission of Öhlins Racing AB 20160 Thailand
    is prohibited.

    You might also like