SERVICE BULLETIN SUMMARY

This Service Bulletin is available at:

www.cic.bombardier.com

MODEL BD-700-1A11 (BD-700)

ATA 11-20

PLACARDS AND MARKINGS

MODIFICATION – EXTERIOR PLACARDS AND MARKINGS –

REPLACEMENT OF REFUEL/DEFUEL PLACARD

The information below is provided for your reference. For full details, please
see corresponding paragraph contained within this bulletin.

EFFECTIVITY 9127, 9130, 9140, 9149, 9152,

9154 to 9158, 9160, 9161, 9164, 9166,
9168, 9170 and 9172
COMPLIANCE Alert

Recommended

Optional

MANPOWER 2 man-hours

KITS and/or PARTS YES No

TOOLING YES No

GSE YES No

REQUIRED FOR SMART PARTS YES No

PREREQUISITE BULLETINS N/A

To place an order for material or kits, please call Bombardier Spare Parts Sales at:
1-888-222-1428 (in North America)
1-316-946-2377 (outside North America)

Jul 11/2006 700-1A11-11-006

Page 1 of 1
 SERVICE BULLETIN This Service Bulletin is available at:
www.cic.bombardier.com

MODEL BD-700-1A11 (BD-700)

ATA 11-20

PLACARDS AND MARKINGS

MODIFICATION – EXTERIOR PLACARDS AND MARKINGS –

REPLACEMENT OF REFUEL/DEFUEL PLACARD

1. PLANNING INFORMATION
A. Effectivity
BD-700-1A11 aircraft, Serial No. 9127, 9130, 9140, 9149, 9152, 9154 to 9158,
9160, 9161, 9164, 9166, 9168, 9170 and 9172.
All other subsequent BD-700-1A11 aircraft are scheduled for the modification in
production (Ref.: Modification Summary, 700T800449).
NOTE: The instructions given in this Service Bulletin are only applicable to
the systems and parts installed at the time of delivery of the aircraft
or as changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent
action changes to make sure that this bulletin can be completed.

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
© 2006, Bombardier Inc. All rights reserved
Challenger*, Global Express*, Global Express XRS*, Global 5000*, Learjet* are Trademarks of Bombardier Inc.

Jul 11/2006 700-1A11-11-006

Page 1 of 7
 MODEL BD-700-1A11

B. Reason
This Service Bulletin replaces the refuel/defuel placard that is installed behind the
refuel/defuel door.
This Service Bulletin gives instructions to remove and discard the old refuel/defuel
placard because the text on the old placard does not agree with the actual
configuration and procedures of the aircraft.
The text in the second line of the SHUTOFF TEST part of the new placard is as
follows:
“WAIT UNTIL “SOV STOP” IS DISPLAYED IN PRESEL WINDOW.”
The text in the second line of the SHUTOFF TEST part of the old placard was as
follows:
“WAIT UNTIL “SOV STOP” IS DISPLAYED IN WINDOW NEXT TO EACH TANK.”
C. Description
This Service Bulletin gives instructions to:
– Get access to the rear of the refuel/defuel door,
– Replace the refuel/defuel placard, and
– Do the Close-out.
D. Compliance
Recommended
E. Approval
The technical content of this Service Bulletin has been approved under
the authority of Transport Canada Civil Aviation (TCCA) Design Approval
Organization (DAO) DAO NO. #93-Q-02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the
FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by the
JAA and by EASA in accordance with established procedures

Jul 11/2006 700-1A11-11-006

Page 2 of 7
 MODEL BD-700-1A11

F. Manpower
NOTES: 1. The man-hours given are estimates to help you schedule the tasks
given in this bulletin. The estimates are for direct labor performed by
an experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower estimates, refer to
SB 700-1A11-00-002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to paragraph 3.). The accumulated curing
time is not included in the labor estimates and should be considered
for planning purposes before you schedule this Service Bulletin.
2 man-hours are necessary to do this modification.
Labor is at no cost if the work is done at Bombardier Business Aviation Services
(BBAS) or Authorized Service Facilities. For Bombardier Aerospace to pay for the
labor, this Service Bulletin must also be scheduled in less than 12 months from its
release date.
G. Material - Cost and Availability
The part given in Paragraph 3 is necessary to do this modification.
For Bombardier Aerospace to pay for this part, send an invoice in less than
12 months from this Service Bulletin release date. Also, the invoice will only be
processed if this Service Bulletin number is written on the invoice as a reference.
For those aircraft in new aircraft warranty at the time of service bulletin distribution,
Smart Parts Plus does not pay for the part at any time.
For those aircraft out of new aircraft warranty at the time of Service Bulletin
distribution, Smart Parts Plus pays for the part for up to one year from Service
Bulletin distribution date.
H. Tooling
No equipment or special tools are necessary.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
– Bombardier Aerospace, Modification Summary, 700T800449, Rev. A
– Global 5000 BD-700 Aircraft Maintenance Manual, Chapters 6, 11, 20 and 51
L. Other Publications Affected
Global 5000 BD-700 Aircraft Illustrated Parts Catalog (AIPC), Chapter 11.

Jul 11/2006 700-1A11-11-006

Page 3 of 7
 MODEL BD-700-1A11

M. Equivalent Service Bulletin

None

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs referenced in the instructions that follow are from the Global
5000 BD-700 Aircraft Maintenance Manual, unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from
the Global 5000 BD-700 Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
Open the refuel/defuel door 142AR and get access to the rear of the door.
B. Modification - Replacement of Refuel/Defuel Placard
(1) Do the modification as follows (refer to Figure 1):
(a) Remove and discard the old refuel/defuel placard. Refer to TASK
11-20-00-000-801:
NOTES: 1. Use the procedure for polyester film decals.
2. Use the procedure that uses solvent.
3. Do not use the procedures that use heat or paint remover.
(b) Install the new refuel/defuel placard. Refer to TASK 11-20-00-400-801.
NOTE: Use the procedure for polyester film decals.
C. Close-out
(1) Close the refuel/defuel door 142AR.
(2) Remove all tools, equipment and unwanted materials from the aircraft.
D. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Support (BBACS).

3. MATERIAL INFORMATION
A. Parts
The part that follows is necessary to do this Service Bulletin and can be purchased
from Bombardier, Spare Parts Center, Montréal:

ITEM PART NUMBER QUANTITY

Placard, Refuel/Defuel GS782-5003-3 1
NOTE: The part number for the item listed above is subject to change without
revision to this Service Bulletin. In case of discrepancy between this list
and any other list, the Illustrated Parts Catalog prevails and shall be used
to determine the latest part number.

Jul 11/2006 700-1A11-11-006

Page 4 of 7
 MODEL BD-700-1A11

B. Material
The consumable materials that follow, or equivalent, are necessary to do this
Service Bulletin. These can be purchased from a local supplier:

DESCRIPTION PART SPECIFICATION QUANTITY SUPPLIER

No./NAME (See Note)
Epoxy, Coating 1900-CG-1 MIL-C-22750 As Code: A
Clear Necessary
CT: 1 hr.
Solvent Diestone DLS - As Code: B
or Necessary
Diestone HFP
or
HFE-71DA
Cloth, Low-lint - - As Code: C
Necessary
Knife, Non- - - As Code: C
Metallic Necessary
Scraper, - - As Code: C
Non-Metallic Necessary
Brush, Paint, - - As Code: C
Natural or Necessary
Synthetic
Bristle
Paper, Kraft - - As Code: C
Necessary
Tape, Masking - - As Code: C
Necessary
NOTES: 1. Bombardier Aerospace does not pay for the consumable materials
listed on the previous page.
2. Refer to the next table for each supplier’s address listed by codes.
3. The Curing Time (CT), if applicable, for each consumable material is
indicated in the table on the previous page with the description of
each product.
4. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information
has changed, the operator is encouraged to use the World Wide Web
to find a local supplier.

Jul 11/2006 700-1A11-11-006

Page 5 of 7
 MODEL BD-700-1A11

SUPPLIERS ADDRESSES BY CODES

Code: A Code: B
Tempo Aerospace Inc. MagChem Inc
205 Fenmar Dr. West 1271 Ampere
Toronto, Ontario Boucherville, Que
Canada Canada, J4B 5Z5
Tel.: (416) 746-2233 Tel.: (450) 655-1344
or
3M Product Information Center
3M Center,
Building 0304-01-01
St. Paul, MN 55144-1000
U.S.A.
Tel.: 1-888-364-3577

Code: C
Commercially Available

Jul 11/2006 700-1A11-11-006

Page 6 of 7
 MODEL BD-700-1A11
STEP 1 STEP 2
REMOVE AND QTY INSTALL QTY
DISCARD
Placard GS782-5003-1 1 Placard (1) GS782-5003-3 1
(not shown)

4.55 in
(11.6 cm)
REF

0.50 in
(12.7 mm) 1
VIEW LOOKING INSIDE DOOR

FSB1106_001

Drawings and data contained herein are the

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.

Modification – Refuel/Defuel Placard Replacement

Figure 1

Jul 11/2006 700-1A11-11-006

Page 7 of 7
 SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)

SERVICE BULLETIN 700-1A11-11-006 ISSUE: Basic DATED: Jul 11/2006

TITLE: Modification – Exterior Placards and Markings – Replacement of Refuel/Defuel Placard

STRONGLY DISAGREE NEUTRAL AGREE STRONGLY
DISAGREE AGREE
• Instructions to do the Service Bulletin ‰ ‰ ‰ ‰ ‰
were accurate.
Comments:

• Illustration(s), figure(s), and/or kit drawing(s) ‰ ‰ ‰ ‰ ‰

were helpful to carry out instructions.
Comments:

• If a kit was required, did the kit contents ‰ ‰ ‰ ‰ ‰

received agree with the contents listed in
the bulletin?
Comments:

• The loose parts listed under Paragraph 3 ‰ ‰ ‰ ‰ ‰

were easily procured.
Comments:

• Work was accomplished in the prescribed time. ‰ ‰ ‰ ‰ ‰

Comments

• Overall, I was satisfied with this Service Bulletin. ‰ ‰ ‰ ‰ ‰

Comments:

PLEASE SUPPLY US WITH THE FOLLOWING DATA AND FAX TO: (514) 855-2535
OPERATOR:

AIRCRAFT SERIAL NO.:

TELEPHONE:

FACSIMILE:

NAME: (Please print)

THANK YOU FOR YOUR RESPONSE!

PLEASE RETURN THIS COMPLETED EVALUATION FORM BY MAIL OR FAX
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

Bombardier Business Aircraft Customer Support (BBACS)

P.O. Box 6087, Station Centre-ville
Montréal, Québec, Canada H3C 3G9

Attention: Supervisor, Service Bulletin Group

Department 631

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
 SERVICE BULLETIN INCORPORATION SHEET –
“700-1A11-11-006”
Upon completion of the Service Bulletin, please fill in this form and either fold and mail in the envelope
provided, or fax to:(514) 855-8798, or e-mail to Fracas at fracas.montreal@aero.bombardier.com

NOTE: For configuration control purposes, please fill out one form for each Service Bulletin.

Further Action
Required
Service Bulletin Rev. * Parts Completed YES NO
Number
700-1A11-11-006 Basic -
- - -
- - -

Actual hours to accomplish Service Bulletin:

Access: Modification: Tests: Restore:

* NOTES: 1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B,
C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A), only the initial check should be reported
unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should be
reported.

Is the aircraft enrolled on the CAMP computerized maintenance program? Yes No

Aircraft Serial No. Aircraft Reg. No.

Airframe Landings Airframe Hours
Date of Incorporation Service Order No.
Facility & Location
Incorporation Bulletin
SIGNED: DATE:
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

Bombardier Business Aircraft Customer Support (BBACS)

P.O. Box 6087, Station Centre-ville
Montréal, Québec, Canada H3C 3G9

Attention: Maintenance Engineering

Department 051

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --