TAC I/A Series

MNB-300 BACnet Unitary Controller

I/A Series Micronet MNB-300 The TAC I/A Series MicroNet MNB-300 BACnet Unitary Controller is an interoperable controller with native BACnet MS/TP communications support. The controller features Sensor Link (S-Link) support, LED status and output indication, screw terminal blocks, as well as a panel mount sub-base with removable electronics module. When programmed using WorkPlace Tech Tool, the Unitary controller provides a wide range of control strategies for packaged rooftop, heat pump, fan coil, unit ventilator, and similar applications. Stand Alone or Connected

SPECIFICATIONS
HArdwArE dimensions 7.0 in. W x 3.94 in. H x 2.19 in. D (178 mm x 100 mm x 56 mm) Enclosure Optional wall-mount enclosure conforms to NEMA-1 requirements. Cover meets UL94V-0 flammability ratings. Mounting Panel mount. wiring Terminals I/O Points Fixed screw terminals; up to two AWG #14 (2.08 mm2) or smaller wire. Power and MS/TP Removable screw terminals; single AWG #14 (2.08 mm2) wire or up to two AWG #18 (0.823 mm2) or smaller wires. ElECTrICAl Power Supply Input 20.4 to 30 Vac, 50/60 Hz. Maximum Power Consumption 16 VA at 24 Vac. ENvIrONMENT Operating Temperature -40 to 140 F (-40 to 60 C) Shipping and Storage Temperature -40 to 160 F (-40 to 71 C) Humidity 5 to 95% RH, non-condensing

The TAC I/A Series BACnet Unitary Controller can function either in a standalone mode or as part of a BACnet building automation system (BAS) network.

AGENCY lISTINGS US FCC Part 15, Class A UL 916, File #E71385 Category PAZX UL 864, Category UUKL, File #S5381 Smoke-Control Equipment Canadian UL Listed to Canadian Safety Standards (CAN/CSA 22.2) CUL Listed to Standards ULC/ORD-C100-92 (Smoke Control System Equipment) and CAN-ULC-S527 (Control Units for Fire Alarm Systems) Australian Meets requirements to bear the C-Tick Mark European Community EMC Directive 89/336/EEC, EN61326 INPUTS ANd OUTPUTS Universal Inputs (6) Universal Input characteristics are softwareconfigured to respond to one of the following input types: 10k ohm Thermistor w/ 11k ohm Shunt resistor Sensor operating range -40 to 250 F (-40 to 121 C) range. TSMN-57011-850, TS-5700-850 Series or equivalent. Specifications continued on next page.

TAC I/A Series

MNB-300 BACnet Unitary Controller COMMUNICATIONS

BACnet Networks The TAC I/A Series MicroNet BACnet Unitary Controller incorporates an isolated EIA-485 (formerly RS-485) transceiver for BACnet MS/TP communications at 9.6 up to 76.8 kbaud using standard MS/TP wiring methods. Up to 128 TAC I/A Series MicroNet BACnet controllers can be connected to an MS/TP sub-net without repeaters. S-link The Sensor Link (S-Link) communications wiring provides power and a communication interface for one MN-Sx MicroNet sensor. The various MN-Sx sensors can provide room temperature, room humidity, setpoint adjustment, and occupancy override. This connection uses two-wire, unshielded cable and is not polarity sensitive. Maximum S-Link bus length is 200 ft (61 m).

Specifications continued from first page. 1k ohm Balco Input -40 to 250 F (-40 to 121 C) range. TSMN-81011, TS-8000 Series or equivalent. 1k ohm Platinum Input -40 to 240 F (-40 to 116 C) range. TSMN-58011, TS-5800 Series or equivalent. 1k ohm resistive 0 to 1.5k ohms. 10k ohm resistive 0 to 10.5k ohms. Analog voltage 0 to 5 Vdc. Analog Current Range 0 to 20 mA, requires an external 250 ohm shunt resistor (AD-8969-202). digital Input Dry switched contact. Detection of closed switch requires less than 300 ohms. Detection of open switch requires more than 2.5k ohms. Standard Pulse Input (UI1-UI6) Minimum rate 1 pulse per 4 minutes. Maximum rate 1 pulse per second. Fast Pulse Input (UI1) Minimum rate 1 pulse per 4 minutes. Maximum rate 10 pulses per second. digital Outputs - Triac (6) 12 VA at 24 Vac, 50/60 Hz, each output individually isolated. Universal Outputs (3) Current 0 to 20 mA (output load from 80 to 550 ohms). voltage 0 to 10 V (with external 500 ohms, 1/2 W, 1% resistor). Capability to drive Functional devices RIBUI1C Relay (UO configured for 0 to 20 mAdc, no external resistor).

BACnet COMPlIANCE
BACnet Application Specific Controller (B-ASC).

FEATUrES
The TAC I/A Series MicroNet BACnet Unitary Controllers sequence of operation and BACnet image are fully programmable, using WorkPlace Tech Tool. The controllers can be applied to all common unitary HVAC applications. Capability to function in standalone mode or as part of a TAC I/A Series building automation network. Integral MS/TP jack for direct connection of PC with WorkPlace Tech Tool. Removable electronics module mates with panelmounted subbase. Removable terminals for power and communications to facilitate commissioning. Optional rugged, NEMA 1 plenum-rated sheet metal enclosure. MS/TP DIP switch addressable. Service pin button for BACnet I am message broadcast.
2009 Schneider Electric. All rights reserved.
pm

Isolated EIA-485 (formerly RS-485) transceiver for MS/TP communications. MS/TP baud rate selection from 9.6 up to 76.8 kbaud. LED indication of MS/TP communication activity, controller status, and UO and DO state. Firmware upgradeable over the network. Support for S-Link Sensor.

BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve, or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a regstered trademark of BI.
Schneider Electric
F-27339-4

1354 Clifford Avenue, P.O. Box 2940, Loves Park, IL 61132-2940, USA

1-888-444-1311

www.schneider-electric.com/buildings
November 2009

TAC I/A Series

MNB-300 BACnet Unitary Controller

INPUTS FrOM MN-SX I/A SErIES MICrONET SENSOrS

Inputs Space Temperature Space Humidity Adjustable Setpoint Override Pushbutton Fan Operation and Speed System Mode Emergency Heat description 32 to 122 F (0 to 50 C) 5 to 95% RH, Non-condensing Adjustable within limits set by application programming tool For standalone occupancy control or occupancy override Fan mode selection: On/Off, Speed (Low/ Medium/High), or Auto System mode selection: Heat, Cool, Off, or Auto Emergency heat mode selection: Enable or Disable MN-Sx Sensor MN-S1, MN-S1HT, MN-S2, MN-S2HT, MN-S3, MN-S3HT, MN-S4, MN-S4HT, MN-S4-FCS, MN-S4HT-FCS, MN-S5 and MN-S5HT MN-S1HT, MN-S2HT, MN-S3HT, MN-S4HT, MN-S4HT-FCS, and MN-S5HT MN-S3, MN-S3HT, MN-S4, MN-S4HT, MN-S4-FCS, MN-S4HT-FCS, MN-S5, and MN-S5HT MN-S2, MN-S2HT, MN-S3, MN-S3HT, MN-S4, MN-S4HT, MN-S5, and MN-S5HT MN-S4, MN-S4HT, MN-S4-FCS, MN-S4HT-FCS, MN-S5, and MN-S5HT MN-S4, MN-S4HT, MN-S5, and MN-S5HT MN-S5 and MN-S5HT

MOdElS
Part Number description Inputs/Outputs UI MNB-300 TAC I/A Series MicroNet BACnet Unitary Controller 6 UO 3 dO (Triac) 6

ACCESSOrIES
Part Number MNB-300-ENC MNB-BASE-300 MNB-CNTLR-300 description Wall-mount enclosure Controller base assembly only Controller cover assembly only TSMN Series Part Number S-Link Sensors description Temperature and humidity wall sensors with digital communication Room temperature sensors

TO1 (DO1)

TO2 (DO2)

TO3 (DO3)

TO4 (DO4)

TO5 (DO5)

TO6 (DO6)

C1

C2

C3

C4

C5

24H

24G (COM)

GND

MNB-300 Unitary Controller

Internal Triac Switches (Isolated)

C6 Physical Address

Schneider Electric
F-27339-4

1354 Clifford Avenue, P.O. Box 2940, Loves Park, IL 61132-2940, USA

1-888-444-1311

www.schneider-electric.com/buildings
November 2009
pm

2009 Schneider Electric. All rights reserved.

STATUS

XMT

RCV

EOL MS+ MSS-LK

IAM

UO1

UO2

COM

COM

COM

COM

UO3

COM

MS/TP Jack

UI1

UI2

UI3

UI4

UI5

UI6

SLD

TAC I/A Series

MNB-300 BACnet Unitary Controller

ArCHITECTUrE
PC Workstation with WorkPlace Tech Tool Software Suite

Ethernet TCP/IP and BACnet/IP

Network Controller TAC I/A Series MicroNet BACnet MNB-1000 Plant Controller S-Link Sensor Remote I/O Trunk TAC I/A Series MicroNet BACnet MNB-1000 Plant Controller

TAC I/A Series MicroNet BACnet MNB-V1 or V2 VAV Controller S-Link Sensor TAC I/A Series MicroNet BACnet MNB-300 Unitary Controller S-Link Sensor

Remote I/O Module One to Eight TAC I/A Series MicroNet BACnet MNB-1000-15 Remote I/O Modules

TAC I/A Series MicroNet BACnet MNB-300 Unitary Controller S-Link Sensor TAC I/A Series MicroNet BACnet MNB-70 Zone Controller S-Link Sensor

BACnet MS/TP Communications Bus

Remote I/O Module

BACnet MS/TP Communications Bus

TAC I/A Series MicroNet BACnet MNB-70 Zone Controller S-Link Sensor TAC I/A Series MicroNet BACnet MNB-300 Unitary Controller S-Link Sensor

Remote I/O Module

TAC I/A Series MicroNet BACnet MNB-V1 Cooling Controller S-Link Sensor

PC Workstation with WorkPlace Tech Tool Software Suite

TAC I/A Series MicroNet BACnet MNB-V2 Deluxe Controller S-Link Sensor
2009 Schneider Electric. All rights reserved.

Distributed, manufactured, and sold by Schneider Electric. I/A Series trademarks are owned by Invensys Systems, Inc. and are used on this product under master license from Invensys. Invensys does not manufacture this product or provide any product warranty or support. For service, support, and warranty information, contact Schneider Electric. On October 1st, 2009, TAC became the Buildings Business of its parent company Schneider Electric. This document reflects the visual identity of Schneider Electric, however there remain references to TAC as a corporate brand in the body copy. As each document is updated, the body copy will be changed to reflect appropriate corporate brand changes. All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. Schneider Electric
F-27339-4

1354 Clifford Avenue, P.O. Box 2940, Loves Park, IL 61132-2940, USA

1-888-444-1311

www.schneider-electric.com/buildings
November 2009
pm