7550 7650 Installation Guide

70002-0247-11 11/2008
PowerLogic ION7550 / ION7650

Energy and power quality meter
Installation Guide
PowerLogic PowerLogic ION7550 / ION7650 Installation Guide
Danger
This symbol indicates the presence of dangerous voltage within and outside the product enclosure that may constitute a risk of electric shock, serious injury or death to persons if proper precautions are not followed.
Caution
This symbol alerts the user to the presence of hazards that may cause minor or moderate injury to persons, damage to property or damage to the device itself, if proper precautions are not followed.
Note
This symbol directs the users attention to important installation, operating and maintenance instructions.
Installation Considerations
Installation and maintenance of the PowerLogic ION7550 / ION7650 meter should only be performed by qualified, competent personnel that have appropriate training and experience with high voltage and current devices. The meter must be installed in accordance with all local and national electrical codes.
DANGER
Failure to observe the following instructions will result in severe injury or death. During normal operation of the ION7550 / ION7650 meter, hazardous voltages are present on its ter-
minal strips, and throughout the connected potential transformer (PT), current transformer (CT), digital (status) input, control power and external I/O circuits. PT and CT secondary circuits are capable of generating lethal voltages and currents with their primary circuit energized. Follow standard safety precautions while performing any installation or service work (i.e. removing PT fuses, shorting CT secondaries, etc.). The terminal strips on the meter base should not be user-accessible after installation. The ION7550 / ION7650 meter is designed to be used as a permanently installed device. All electrical connections to the meter must be installed with a permanent connection method (screw-type mechanical connection). The ION7550 / ION7650 meter chassis ground must be permanently connected to the switchgear earth ground. Do not use digital output devices for primary protection functions. These include applications where the devices perform energy limiting functions or provide protection of people from injury. Do not use the ION7550 / ION7650 in situations where failure of the devices can cause injury or death, or cause sufficient energy to be released that can start a fire. The meter can be used for secondary protection functions. Do not HIPOT/Dielectric test the digital (status) inputs, digital outputs, or communications terminals. Refer to the label on the ION7550 / ION7650 meter for the maximum voltage level the device can withstand.
CAUTION
Observe the following instructions, or permanent damage to the meter may occur. The ION7550 / ION7650 meter offers a range of hardware options that affect input ratings. The
ION7550 / ION7650 meters serial number label lists all equipped options. Applying current levels incompatible with the current inputs will permanently damage the meter. This document provides installation instructions applicable to each hardware option. The ION7550 / ION7650 meters chassis ground must be permanently connected to the switchgear earth ground for the noise and surge protection circuitry to function correctly. Failure to do so will void the warranty. Terminal screw torque: Barrier-type (current, voltage, and relay terminal screws: 1.35 Nm (1.00 ft-lbf) max. Captured-wire type (digital inputs/outputs, communications, power supply: 0.90 Nm (0.66 ft.lbf) max.
2008 Schneider Electric. All rights reserved.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The Ringer Equivalence Number (REN) for the ION7550 / ION7650 optional internal modem is 0.6. Connection to the ION7550 / ION7650 internal modem should be made via an FCC Part 68 compliant telephone cord (not supplied). The ION7550 / ION7650 cannot be used on a public coin phone service or party line services.
Network Compatibility Notice for the Internal Modem

The internal modem in meters equipped with this option is compatible with the telephone systems of most countries in the world. Use in some countries may require modification of the internal modems initialization strings. If problems using the modem on your phone system occur, please contact Schneider Electric Technical Support.
Standards Compliance
CSA: Certified to CAN/ Certified to CSA C22.2 No.1010-1 UL 3111

Made by Power Measurement Ltd. PowerLogic, ION, ION Enterprise, MeterM@il, WebMeter and Modbus are either trademarks or registered trademarks of Schneider Electric. Covered by one or more of the following patents: U.S. Patent No's 7010438, 7006934, 6990395, 6988182, 6988025, 6983211, 6961641, 6957158, 6944555, 6871150, 6853978, 6825776, 6813571, 6798191, 6798190, 6792364, 6792337, 6751562, 6745138, 6737855, 6694270, 6687627, 6671654, 6671635, 6615147, 6611922, 6611773, 6563697, 6493644, 6397155, 6236949, 6186842, 6185508, 6000034, 5995911, 5828576, 5736847, 5650936, D505087, D459259, D458863, D443541, D439535, D435471, D432934, D429655, D427533.
PowerLogic ION7550 / ION7650 Models

Integrated Display Model
Comes with front optical port.
TRAN (transducer) Model

The TRAN model has no display.
Available Options
Option
Form Factor

Current Inputs
Standard
COM
Standard (RS-232,
I/O
Standard (8 digital
Security
Standard1 RMANSI2
ION7550
Integ. Display TRAN 5 MB memory 10 MB memory Up to 256 sampling rate
(5 Amp)
RS-485, optical)
1 Amp
Power Supply
Standard Low Voltage
Ethernet RJ45 Ethernet Fiber Modem
DC
inputs, 3 Form C relays, 4 Form A outputs) Extra 8 digital inputs Four 0-1mA analog inputs Four 0-20 mA analog inputs Four -1 to 1mA analog outputs Four 0-20 mA analog outputs
Model
Form Factor

Current Inputs
COM
Same as
I/O
Same as ION7550
Security
Same as
ION7650
Integ. Display Same as ION7550 TRAN 5 MB memory Power Supply 10 MB memory Same as Up to 512 ION7550 sampling rate (standard) 1024 sampling rate (optional) EN50160 compliance IEC61000-4-30 Class A compliance
ION7550
ION7550
Notes
1 2
Standard = password protected, no locking or sealing. RMANSI = ANSI C12.16 approved revenue meter; meets ANSI C12.20 class 0.2 accuracy standards.
Before You Begin

Before installing the meter, familiarize yourself with the steps in this guide and read the safety precautions presented on the Installation Considerations page.
DANGER
Do not power up the meter until the current and voltage wiring is completed.
Recommended Tools

Phillips screwdriver Precision flat-head screwdriver Wire cutters / stripper
Meter Overview
Meter Front Meter Back
Voltage and Current Inputs
Digital Inputs
Analog Inputs
Analog Outputs
Softkeys
ESC
Button
I/O Expansion Card
Optical Port
Power Supply
Communications Card
Ground Terminal
Operational LEDs
Navigation Buttons
PROG/SELECT
Button
Form C Digital Outputs
Digital Inputs
Form A Digital Outputs
Front Panel Button Functions

PROG
PROG/SELECT: Press the PROG/SELECT (program or select) button to enter Setup mode. In Setup mode, press the PROG/SELECT button to accept changes. ESC:
ESC
Press the ESC (Escape) button to return to a higher menu or discontinue a configuration change.
NAVIGATION:
Press the UP / DOWN arrow buttons to highlight menu items, or increment / decrement numbers. Press the LEFT or RIGHT arrow buttons to move to an adjacent digit.
SOFTKEY: Press a SOFTKEY button to select the parameter that you want to configure from the sub-menus.
Unit Dimensions
Basic Model Rear View
Basic Model Front View
Basic Model Side View
Step 1: Mount the Meter

Environmental Specifications
Mounting Location Operating Range Display Operating Range Storage Range Relative Humidity Range Indoor use -20 to +70C (-4 to +158F) Standard Power Supply -20 to +50C (-4 to +122F) Low Voltage DC Power Supply No formation of ice -20 to +70C (-4 to +158F) -40 to +85C (-40 to +185F) 5 to 95% non-condensing
Meter Battery Considerations

The meters battery life expectancy depends on both temperature and the amount of time the meter is without power. For typical installations, the battery should last 20 years or more. If the meter is not powered, the battery will last a minimum of 7 years at room temperature.
Integrated Display Model

1. 2. Fit the meter into the DIN standard 192 cutout (186 mm by 186 mm). Slide the four brackets into their slots on the back of the meter and secure using the four Phillips head screws. Do not overtighten.
Screw
DIN 192 Cutout
Bracket
Step 2: Wire the Ground Terminal

Connect the terminal to a good earth ground with a 2.1 mm2 (14 AWG) wire. Ensure that the terminal nut is tightened down securely onto the ground wire. Do not use metal door hinges as a grounding point.
Step 3: Wire the Digital I/O and Analog I/O

Form C Digital Outputs: Mechanical Relays R1 - R3
Internal Form C Mechanical Relay
R11 R12
R13
R11 R12 R13 R21
Type Contacts Wire Connector Voltage Rating Rated Load @ Rated Voltage Max. Voltage MOV Protection Max. Load @ Max. Voltage Turn-On Time Isolation Turn-Off Time Lifetime Update time
Form C (R1, R2, R3) K (common), Y (NO), Z (NC) Use wiring that is appropriate for the application Ring or split ring connector 250 VAC / 30 VDC Resistive: 10 A (AC/DC) Inductive (PF=0.4): 7.5 A (AC) / 5 A (DC) 380 VAC / 125 VDC between K and NO/NC 300 V max. between NO and NC 3 A (AC) / 0.2 A (DC) 15 ms max. 5,000 VAC for 60 s 5 ms max. No load = 10,000,000 operations Rated voltage and load = 100,000 operations cycle or 1 s NO K NC
Mechanical relays should always be protected by external fuses
Meter
Alarm Lamp
Load
External Supply
Form A Digital Outputs: Solid State Relays D1 - D4

Type
Internal Form A Solid State Relay
Form A (D1, D2, D3, D4) 1.3 to 0.1 mm2 (16 to 28 AWG) Continuous or pulse 30 VDC 80 mA per channel Optically isolated; max. 5,000 V RMS isolation (UL-E91231) cycle or 1 s Meter
Wire Signal Type Max. Load Voltage Max. Load Current Isolation
D1
D3 - +
DIGITAL OUTPUTS
D3
D2
D1
+
1.8 Wh
External Supply 30VDC max D4 output is factory-configured to pulse once every 1.8 Wh for Class 20 meters, or once every 0.18 Wh for Class 2 meters (for calibration testing purposes).
2008 Schneider Electric. All rights reserved. 9
External Relays
D4 - +
D2 - +
+
D1 - +
Scan Time
Digital Inputs: S1 - S8
DIGITAL INPUTS
S C O M S S 8 7 S 6 S S 5 4 S 3 S 2 S 1
Type Application Wire Min. Pulse Width Max. Pulse Rate Timing Resolution Updated Isolation to Ground Max. External Voltage
Self-excited (internal 30 VDC supply) Dry contact sensing, or with external excitation 1.3 to 0.1 mm2 (16 to 28 AWG) 1 ms 20 pulses per second 1 ms cycle (after timing resolution) max. 200 VDC for 10s 130 VDC continuous External Excitation Meter
_
S7
Internal Excitation Meter

_
S7
_
+
S8
_
+
S8
30 VDC +
SCOM
Opticallycoupled switch
30 VDC + +
SCOM
External Supply
130 VDC max
Digital Inputs (Meter Ordering Option): DI1 - DI8

Type Application Wire Min. Pulse Width Max. Pulse Rate Timing Resolution Updated Isolation to Ground Max. External Voltage Self excited (internal 30 VDC supply) Dry contact sensing, or with external excitation 1.3 to 0.1 mm2 (16 to 28 AWG) 20 ms 25 pulses per second 2 ms cycle (after timing resolution) 750 VDC 50 VDC continuous External Excitation Meter
Internal Excitation Meter
External Supply
50 VDC max
10
Analog Inputs (Meter Ordering Option): AI1 to AI4

Type Wire
+ -
Captured wire connector 1.3 to 0.1 mm2 (16 to 28 AWG) DC current 0 to 20 mA (scalable 4-20 mA) or 0 to 1 mA 24 (0-20 mA option) or 475 (0-1 mA option) +/ 0.3% of full scale 1s 750 V max 400 k (channel/channel) Meter
+ AI1
AI3
Signal Type Available Options Input Impedance Accuracy Update Rate Isolation to Ground Isolation Impedance
AI4
AI3
AI2 AI1
Thermocoupler
mV
mA
Voltage-toCurrent Transducer
Example application: temperature sensing
NOTE
Do not connect the analog inputs of the I/O card to the analog outputs on the same I/O card.
Analog Outputs (Meter Ordering Option): AO1 to AO4

Type Wire
OUT COM
Captured wire connector 1.3 to 0.1 mm2 (16 to 28 AWG) DC current 0 to 20 mA (scalable 4-20 mA) or -1 to 1 mA (scalable 0-1 mA) 500 (0-20 mA option) or 10 k (-1 to 1 mA option) +/ 0.30% of full scale cycle or 1 s min. 1 cycle for measurement + cycle for ION + 1 s delay for hardware 750 V Meter
AO3
Signal Type Available Options Driving Capability
AO4 A03 A02 AO1
Accuracy Update Rate Latency Isolation to Ground
Analog Meter
OUT
AO1
COM
Example application: driving an analog meter with the DC current output
NOTE
Do not connect the analog outputs of the I/O card to the analog inputs on the same I/O card.
11
Step 4: Wire the Voltage and Current Inputs

V1 V2 V3 V4 Vref I11 I12 I21 I22 I31 I32 I41 I42
3~ CURRENT INPUTS
I51 I52
3~ VOLTAGE INPUTS
Voltage Inputs
Connector Type Wire Gauge Rated Inputs Fault Capture Overload Dielectric Withstand Input Impedance Ring or split ring connector 3.3 to 2.1 mm2 (12 to 14 AWG) 347 V L-N RMS /600 V L-L RMS 1200 V L-N peak 1500 VAC RMS continuous 2500 VAC RMS at 60 Hz for 60 s 5 M/phase (phase - Vref)
Current Inputs: Class 20 Current Inputs (5A Option)

Connector Type Wire Gauge Input Rating Starting Current Fault Capture Max. Voltage Overload Dielectric Withstand Burden Impedance Ring or split ring connector 5.3 to 3.3 mm2 (10 to 12 AWG): Use 8.4 mm2 (8 AWG) for 10-20 A applications 5 A, 10 A, and/or 20 A RMS 0.005 A RMS 70 A peak 600 V RMS (CAT III IEC61010-1) 500 A RMS for 1 s, non-recurring 2500 VAC RMS at 60 Hz for 60 s 0.05 VA per phase (at 5 A) 0.002 per phase
Current Inputs: Class 2 Current Inputs (1A Option)

Connector Type Wire Gauge Input Rating Starting Current Fault Capture Max. Voltage Overload Dielectric Withstand Burden Impedance Ring or split ring connector 5.3 to 3.3 mm2 (10 to 12 AWG) 1 A, 2 A, 5 A, and/or 10 A RMS 0.001 A RMS 17.5 A peak 600 V RMS (CAT III IEC61010-1) 50 A RMS for 1s, non-recurring 2500 VAC RMS at 60 Hz for 60 s 0.015 VA per phase (at 1 A) 0.015 per phase
NOTE
The appropriate Volts Mode setting is included with each wiring diagram. Refer to Step 8 to learn how to configure Volts Mode on the meter.
12
4-Wire Wye, 3-Element, Direct Connection Diagram

Fuse for N/- terminal required if its supply source is ungrounded Connect G terminal to ground for AC power source
4-Wire Wye, 3-Element, 3 PTs Connection Diagram

4-Wire Wye, 2-Element, 2 PTs Connection

LINE
347 V L-N / 600 V L-L max. VOLTS MODE = 4W-Wye
I4 Optional
LOAD LOAD
LINE LINE
I4 Optional
Use PTs for voltages over 347 V L-N / 600 V L-L. Wye (Star) wiring for PT primaries and secondaries. VOLTS MODE = 4W-Wye
I4 Optional
Phase B voltage (V2) displayed by meter is derived from phase A and phase C, not measured. V2 will display a value even if no voltage is present on Phase B. V2 values are only accurate for balanced loads. VOLTS MODE = 3W-Wye
LOAD
13
3-Wire Solid-Grounded Wye, 3-Element, Direct Connection

LOAD LINE
A B C
When the common or star point of a 3-wire Wye system is grounded, the meter may be connected directly without using PTs, provided that the phase voltages are within the meters range. VOLTS MODE = 4W-Wye
3-Wire Delta, 2-Element, Direct Connection

LOAD
3-Wire Delta, 2-Element 2 PTs & 2 CTs

A B C
LINE LINE
2A
Do not connect
3A
V1
V2 V3 V4 Vref I11 I12 I21 I22 I31 I32 I41 I42 I51 I52
L / + N/-
600 V L-L max. VOLTS MODE = Delta
LOAD
2A
3A
V1
L / + N/-
Use PTs for voltages over 600 V L-L. VOLTS MODE = Delta
14
3-Wire Delta, 2-Element, 2 PTs & 3 CTs

A B C
LOAD
Single Phase Connection Diagram

Using Potential Transformers

System Mode Wye Voltage Range 120 V L-N or 208 V L-L 277 V L-N or 480 V L-L 347 V L-N or 600 V L-L over 347 V L-N or 600 V L-L 120 V L-N or 240 V L-L 277 V L-N or 554 V L-L over 277 V L-N or 554 V L-L up to 600 V L-L over 600 V L-L no no no yes no no yes no yes Requires PTs
Single Phase Delta
LINE
2A
3A
V1
L / + N/-
Use PTs for voltages over 600 V L-L VOLTS MODE = Delta
LINE
I4 Optional
277 V L-N / 554 V L-L max. Use PTs for higher voltages. VOLTS MODE = Single
LOAD
15
Step 5: Wire the Communications

RS-232 Connections (COM1)
DB9 Null Modem Wiring Diagram
DTE (computer)
DTE (meter)
Null modem cable pinout Pin 3 - Transmit Data - Pin 2 Pin 2 - Receive Data - Pin 3 Pin 7 - Request to Send- Pin 8 Pin 8 - Clear to Send- Pin 7 Pin 5 - Signal Ground- Pin 5 Pin 6 - Data Set Ready- Pin 4 Pin 4 - Data Terminal Ready- Pin 6
Specification Connector Type Wire Maximum Cable Length Data Rate Isolation Duplex Compliance
Meter Connected to Computer
Meter Connected to External Modem
DB9 female end for mating with male connector on the meter Null modem RS-232 cable Straight-through RS-232 cable 15.2 m (50 ft) 300 115,200 bps Optical Full ANSI/IEEE C37.90.1-2002 surge withstand and fast transient tests
RS-485 Connections (COM1 and COM2)

SH + RS-485 Shield (electrically connected to chassis ground) RS-485 Data Minus RS-485 Data Plus Captured wire Shielded twisted pair RS-485 cable, 0.33 mm2 (22 AWG) or larger 1219 m (4000 ft) total for entire bus 300 115,200 bps 32 Optical Half ANSI/IEEE C37.90.1-2002 surge withstand and fast transient tests
Connector Type Wire Maximum Cable Length Data Rate Maximum Devices (per bus) Isolation Duplex
Connect SH at one end only
Compliance
Infrared Connections (COM4)

Interface Location Data Rate Duplex ANSI C12.18 Type II optical port Front of meter 1,200 19,200 bps Half
16
Ethernet Connections (if equipped)

10BASE-T / 100BASE-TX
Pin 1: Transmit Data + Pin 2: Transmit Data Pin 3: Receive Data + Pin 6: Receive Data -
Wire Type Connector Type Maximum Length
High quality Category 5 or 6 unshielded twisted pair cable RJ45 modular 100 m (328 ft) IEEE 802.3 10/100BASE-T for 10/100 Mbps base band CSMA/CD Type LANs Data Rate 10/100 Mbps Isolation Transformer isolated to 1500 V RMS Max. Connections Allowed 4 simultaneous (32 via Modbus TCP/IP)
100BASE-FX (Fiber)
62.5/125 or 50/125 micrometer multimode fiber optic cable Connector Type SC 2000 m (6562 ft) full duplex Maximum Length 400 m (1312 ft) half duplex Data Rate 100 Mbps Isolation Optical Wire Type
SC type fiber cable
Ethernet TCP/IP Service Ports

Protocol ION Modbus RTU Modbus TCP EtherGate (COM1) EtherGate (COM2) DNP TCP SMTP Port 7700 7701 502 7801 7802 20,000 25 (configurable)
Only one EtherGate connection per port is allowed at a time
Internal Modem Connection (COM3 if equipped)

Pin 3: Ring Pin 4: Tip
Connector Type Wire Type Data Rate Error Correction Data Compression
RJ11 FCC Part 68 compliant telephone cord (two male RJ11 ends) 300 bps 56 kbps V.42 LAPM, MNP 2-4, V.44 V.42 bis/MNP 5
17
Step 6: Wire the Power Supply

Specification Type Standard Power Supply Captured wire connector 3.3-2.1 mm2 (12-14 AWG) 2.1-0.8 mm2 (14-18 AWG) Low Voltage DC
G L+ N_
Wire Rated Inputs
85-240 VAC 10%(47-63 Hz), 20-60 VDC 10% or 110-300 VDC 10% Dielectric Withstand 2500 VAC RMS at 60 Hz for 60s Burden 35 VA max. (15 VA typical) 18 W max. (12 W typical) Ride-through 100 ms (6 cycles at 60 Hz) min. None
Step 7: Power Up the Meter

1. 2. 3. Ensure the ground wire is securely connected on both ends. Ensure the meters power supply voltage is within the allowed range. Power up the meter.
Step 8: Set Up the Meter Using the Front Panel

The following Setup screens are available for meter configuration via the front panel:
BASIC SETUP COM1 SETUP COM2 SETUP COM3 SETUP COM4 SETUP NETWORK SETUP PQ SETUP FORMAT SETUP DISPLAY SETUP TIME SETUP SECURITY SETUP METER RESETS
Use the PROG/SELECT, ESC, softkeys and arrow buttons to configure settings. The following example shows Volts Mode setup using the meter front panel.
Press Press Press
Press Press
Press PROG/SELECT to enter Setup Mode from Display Mode.
Press
Use arrow buttons to move up and down in list. Press PROG/SELECT to select Basic Setup.
Use arrow buttons to move up and down in list. Press PROG/SELECT to select PT/CT Setup.
Press Mode softkey. Use arrow buttons to move up and down in list. Press PROG/SELECT to select Delta.
18
Password
A password is required for all front panel configuration changes and to enter the Security Setup menu. The password is set to 0 (zero) in the factory. The front panel only prompts you for the meter password once, before you make your first configuration change. You can disable the password via the Security Setup menu.
Selecting the Front Panel Language

Meters are shipped with English as the default front panel language. To select another language: 1. 2. Press PROG/SELECT and the right arrow buttons, hold for two seconds then release. Scroll through the language list and select the language you want.
3.
Press PROG/SELECT to confirm.
You can also access this setting via the Display Setup menu.
NOTE
The meter only communicates to software in English.
19
Front Panel Setup Menu Settings

The following table lists all settings that can be configured via the front panel. Menu Setting
VOLTS MODE PT PRIMARY PT SECONDARY CT PRIMARY CT SECONDARY V4 PRIMARY V4 SECONDARY I4 PRIMARY I4 SECONDARY I5 PRIMARY
Description
Range (Values)
Default
4W-WYE 120.00 120.00 5.00 5.00 120.00 120.00 5.00 5.00 5.00 5.00 120.00 120.00 Normal Normal Normal Normal Normal Normal Normal Normal Normal
The power systems configuration 4W-WYE, DELTA, 3W-WYE, WYE, DELTA, etc. SINGLE, DEMO The Potential Transformers primary 1 to 999,999.99 winding voltage rating The Potential Transformers secondary winding voltage rating The Current Transformers primary winding current rating The Current Transformers secondary winding current rating 1 to 999,999.99 1 to 999,999.99 1 to 999,999.99
The Potential Transformers primary 1 to 999,999.99 winding voltage rating on V4 The Potential Transformers secondary winding voltage rating on V4 The Current Transformers primary winding current rating on I4 The Current Transformers secondary winding current rating on I4 The Current Transformers primary winding current rating on I5 The Current Transformers secondary winding current rating on I5 1 to 999,999.99 1 to 999,999.99 1 to 999,999.99 1 to 999,999.99 1 to 999,999.99
BASIC SETUP
I5 SECONDARY V NOMINAL V4 NOMINAL Va POLARITY Vb POLARITY Vc POLARITY V4 POLARITY Ia POLARITY Ib POLARITY Ic POLARITY I4 POLARITY I5 POLARITY
The V1, V2 and V3 nominal voltage 1.000 to 999,999.000 used for harmonics calculations The V4 nominal voltage used for harmonics calculations The polarity of the Potential Transformer on Va The polarity of the Potential Transformer on Vb The polarity of the Potential Transformer on Vc The polarity of the Potential Transformer on V4 The polarity of the Current Transformer on Ia The polarity of the Current Transformer on Ib The polarity of the Current Transformer on Ic The polarity of the Current Transformer on I4 The polarity of the Current Transformer on I5 1.000 to 999,999.000 Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted Normal or Inverted
CURRENT PROBE The type of current probes being TYPE used with the meter
Factory Default, User Defined 1, Factory or User Defined 2 Default
20
Menu
Setting
PROTOCOL
Description
The communications protocol
Range (Values)
Default
ION, Modbus RTU, Modbus Master, DNP V3.00, ION GPS:Truetime/Datum,GPS: Arbiter, GPS:Arbiter-Vorne, Factory, Ethergate, ModemGate 3001, 1200, 2400, 4800, 9600, 19,200 19200, 38400, 57600, 115200 0 to 1 0.010 From serial number2 RS232 RTS + DELAY OFF ION 19,200 0.010 101
COM1 SETUP
BAUD RATE TRAN DELAY UNIT ID SERIAL PORT MODE
The data rate, in bits per second The transmit delay in seconds
Every meter on an RS-485 network 1 to 9999 must have a unique Unit ID number Parity and stop bits for the port Hardware mode for the port RS232 or RS485 RTS + DELAY or RTS/CTS ON or OFF See COM1 protocol 19200, 38400, 57600, 115200 0 to 1 3001, 1200, 2400, 4800, 9600,
8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1
Specifies the handshake mode FLOW CONTROL when COM1 is set to RS232 RS485 BIAS PROTOCOL Turns on biasing when Mastering on the RS-485 bus The communications protocol The data rate, in bits per second The transmit delay in seconds
COM2 SETUP
BAUD RATE TRAN DELAY UNIT ID SERIAL PORT RS485 BIAS
Every meter on an RS-485 network 1 to 9999 must have a unique Unit ID number Parity and stop bits for the port Turns on biasing when Mastering on the RS-485 bus
8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1 ON or OFF ION, Modbus RTU, Modbus Master, DNP V3.00, GPS:Truetime/Datum,GPS: Arbiter, GPS:Arbiter-Vorne, Factory OFF
PROTOCOL
The communications protocol
ION
COM3 SETUP
BAUD RATE TRAN DELAY UNIT ID ANSWER HR RINGS NON-ANSWER HR RINGS PROTOCOL
The data rate, in bits per second The transmit delay in seconds
3001, 1200, 2400, 4800, 9600, 19,200 19200, 38400, 57600, 115200 0 to 1 0.010 102 1 5 ION 9600 0.010 103
Every meter on an RS-485 network 1 to 9999 must have a unique Unit ID number The number of rings during defined 0 to 255 answer hours The number of rings during defined 0 to 255 non-answer hours The communications protocol The data rate, in bits per second The transmit delay in seconds ION, Modbus RTU, DNP V3.00, Factory 1200, 2400, 4800, 9600, 19200 0 to 1
COM4 SETUP
BAUD RATE TRAN DELAY UNIT ID SERIAL PORT
Every meter on an RS-485 network 1 to 9999 must have a unique Unit ID number Parity and stop bits for the port
8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1
21
Menu
Setting
IP ADDRESS SUBNET MASK GATEWAY DNS PRIMARY DNS SECONDARY 10/100BT CONFIG
Description
Sets the IP address for the meter Used if subnetting applies to your network Used in multiple network configurations Sets the address for the primary DNS Server that is configured to resolve domain names Sets the address for the secondary DNS Server that is configured to resolve domain names Sets the BASE-T Ethernet max. link speed and duplexing
Range (Values)
000.000.000.000 to 999.999.999.999 000.000.000.000 to 999.999.999.999 000.000.000.000 to 999.999.999.999 000.000.000.000 to 999.999.999.999 000.000.000.000 to 999.999.999.999 Auto, 10BT half, 10BT full, 100BTX half, 100BTX full Full Duplex or Half Duplex
Default
varies3
255.240.0.0
NETWORK SETUP
0.0.0.0 none
none Auto Full Duplex Disabled 106
100BFX CONFIG Sets the Fiber Ethernet duplexing SNMP SERVER SWELL LIMIT
Determines whether SNMP protocol Enabled or Disabled is enabled on the meter or not Specifies the magnitude above which an input must rise for a swell 100 to 1000 to be recorded Specifies the magnitude below which an input must fall for a sag to 0 to 100 be recorded Specifies the amount by which an input must change during a 0 to 100 disturbance to be considered a new sub-disturbance Specifies the nominal voltage of the 0 to 1,000,000 power system Assigns a priority level to sag/swell events Specifies symbols used to delimit thousands & decimal place holder Number of decimal places displayed for voltages Number of decimal places displayed for currents 0 to 255 1000.0 or 1,000.0 or 1000,0 1. to 123456789.XXX 1. to 123456789.XXX
SAG LIMIT
88
PQ SETUP
CHANGE CRITERIA NOMINAL VOLTAGE4 EVENT PRIORITY DIGIT GROUP VOLTS DECIMAL CURRNT DECIMAL POWER DECIMAL
10
0 200 1000.0 1.XX 1.XXX 1.XXX IEEE ABC IEEE LD/LG MM/DD/ YYYY 24 H Yes
Number of decimal places 1. to 123456789.XXX displayed for power measurements Specifies the convention used for displaying measurements Specifies how phases are labelled Specifies the power factor sign convention used Sets how power factor is labelled (LD = leading/LG = lagging) Specifies how dates are displayed IEEE or IEC ABC, RST, XYZ, RYB, RWB, 123 IEEE or IEC LD/LG, +/-, CAP/IND MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD
FORMAT SETUP
MEAS SYMBOL PHASE LABEL PF SIGN PF SYMBOL DATE FORMAT TIME FORMAT DISPLAY DST
Specifies whether time is displayed 12 H or 24 H in 12 hour or 24 hour clock format Specifies whether or not DST is displayed Yes or No
22
Menu DISPLAY SETUP
Setting
UPDATE RATE CONTRAST DELTA VECTORS LANGUAGE TZ OFFSET DST OFFSET
Description
Sets when the display updates Higher numbers are sharper Specifies how vector diagrams are displayed when in Delta mode Specifies the language used on the meters front panel Sets the time zone of the meters location, relative to UTC 0 to 9
Range (Values)
1 to 6 (seconds) 1 7
Default
System or Instrument English, Spanish, French, Russian - 12:00 to +13:00
System English +00:00 +00:00 COM1 UTC Line Freq
TIME SETUP
Sets the daylight savings time offset -3:00 to +3:00 of the meters location Sets the port to receive time synchronization signals Specifies whether time sync signals are received in local time or UTC Sets the local date Sets the local time Sets the meter password Enables or disables meter security Enables or disables web browser configuration of the meter Enables or disables internal web server on the meter
1 2 3 4
SYNC SOURCE SYNC TYPE
Ethernet, COM1, COM2, COM3, COM4 Local Time or UTC Internal, Line Freq or COMM Same as Date Format setting 00000000 to 99999999 Yes or No Enabled or Disabled Yes or No
CLOCK SOURCE Specifies time sync source LOCAL DATE LOCAL TIME PASSWORD
00000000 No Enabled Yes
SECURITY SETUP
ENABLED WEB CONFIG WEB ACTIVE
A baud rate of 300 bps is only intended for paging applications. Serial number = PA-0302B222-01, Unit ID = 2222 Default IP ADDRESS = 172.16.xxx.xxx, where the last two bytes (decimal) match the last two bytes of the meters MAC address (hex). NOMINAL VOLTAGE must be set to your systems nominal voltage to activate the meters power quality features.
Step 9: Verify Meter Operation

The LEDs on the back of the meter flash during communications. LED
Ethernet 100 (Speed) Ethernet TX Ethernet RX/LINK Modem DCD Modem RI COM3 (Modem) TX COM3 (Modem) RX COM2 TX COM2 RX COM1 TX COM1 RX
Color
Green Green Green Green Green Yellow Yellow Yellow Yellow Yellow Yellow
Function
Off = link at 10 Mb, On = link at 100 Mb Blinking indicates Ethernet transmission On = link up, Off = link down Blinking indicates Ethernet reception Indicates a carrier signal is detected (active connection to the modem) Indicates a ring is detected by the modem Indicates serial transmission on COM3 Indicates serial reception on COM3 Indicates serial transmission on COM2 Indicates serial reception on COM2 Indicates serial transmission on COM1 Indicates serial reception on COM1
23
The LEDs on the front panel indicate the following:

Top (green) LED indicates the meter is operational. The light should always remain on when the meter is in service. Watt-hour pulsing Middle (red) LED is a watt-hour pulser. During normal operations this LED should blink intermittently as the meter measures power. Bottom (red) LED is user programmable. It can be used for Alarm notification. See the ION7550 / ION7650 User Guide for more information.
Front Panel
Phasor Diagrams
You can also view the meters phasor diagram in real time. Use the Phasor Viewer available in PowerLogic ION Setup v2.1 and later (free download from the PowerLogic website) to verify your meters wiring. See the ION Setup online help for details.
NOTE
The following DELTA phasor diagrams are represented in System mode view.
DELTA phasors for UNITY Power Factor (resistive load)

Applicable Volts Mode = DELTA
VCA IC ABC Rotation IB ACB Rotation IA VAB VBC
VAB IB IA
IC VBC VCA
24
WYE - ABC Rotation

Applicable Volts Mode = 4W-WYE and 3W-WYE
Q2: Leading PF (+)

VC IB
Q1: Lagging PF (-)

VC IC
+kVAR
Reactive Power
Active Power -kW Q3: Lagging PF (-)

VC IB VA
WYE - ACB Rotation

Applicable Volts Mode = 4W-WYE and 3W-WYE

VB
Rotation IA VB IC IA Rotation VB IC
Rotation
VA
VA IB VB IA
Active Power +kW Q4: Leading PF (+)

VC IA VA
IC
Reactive Power
Rotation
-kVAR
VB
IB
Q2: Leading PF (+)

VB IC
Q1: Lagging PF (-)

VB IB
+kVAR
Reactive Power
Rotation IA VC IB IA IC Rotation VC IB
Rotation
VA
VA IC VC IA

VB IB
IA VA
Rotation
Reactive Power
VA
-kVAR
IC VC
25
2 Element (3Wire) DELTA - ABC Rotation

Q2: Leading PF (+)

VCA IB Rotation
Q1: Lagging PF (-)

VCA IC Rotation IB VAB
VAB IA IC VBC
+kVAR
Reactive Power
IA VBC
Active Power -kW
Active Power +kW
Q3: Lagging PF (-)

VCA IA Rotation Rotation IC VBC
VBC IC
Q4: Leading PF (+)

VCA IC
IA VAB
Reactive Power
VAB IB
2 Element (3Wire) DELTA - ACB Rotation

-kVAR
IB VBC
Q2: Leading PF (+)
Q1: Lagging PF (-)

VBC IB Rotation
+kVAR
Reactive Power

VBC IC
Rotation Rotation IA VCA
IB VAB
VAB IA IC
IA VCA VCA

VBC IA Rotation
Reactive Power
VAB
IB IC VCA
VAB
-kVAR
IB
26
Step 10: View Meter Data

Use the softkeys to select which data to display. Use the left and right arrow buttons to scroll through the available display screens.
Display Screens
Softkey V,I,PF Volts Amps Power Energy1 Demand1 Pk Dmd1 V Bar, I Bar, P Bar Summary1, Summary2 D Inputs DI - I/O D-Output Anlg - I/O Phasors Name Plt Events Setpoint Energy2 Demand2 Pk Dmd2 THD V1 Harm, V2 Harm,... I1 Harm, I2 Harm,... TOU TOU Egy TOU Dmd1 & TOU Dmd2 *PQ Freq *PQ Vmag1 *PQ Vmag2 *PQ Flk1 *PQ Flk2 *PQ Vdist *PQ Vunb *PQ Vhrm1 *PQ Vhrm2 V-Trend, I-Trend, P-Trend * Contents Volts, Amps, Power Factor Volts Amps Total Power Energy delivered Demand delivered Peak Demand delivered Voltage, Current and Power Bar Graphs Volts/Amps Summary, Power Summary Digital Inputs Digital I/O on expansion I/O card Digital Outputs Analog In and Out Phasors Nameplate information Events Setpoint status Energy received Demand received Peak Demand received Volts and Amps Total Harmonic Distortion V1, V2, V3, V4 harmonics I1, I2, I3, I4, I5 harmonics Time Of Use Active Rate / Season TOU Energy delivered TOU Peak Demand 1 and 2 Power Quality Power Frequency PQ Supply Voltage 1 PQ Supply Voltage 2 PQ Flicker 1 PQ Flicker 2 PQ Voltage Disturbance PQ Voltage Unbalance PQ Voltage Harmonics 1 PQ Voltage Harmonics 2 Voltage, Current, Power Trends
Additional display screens for ION7650 meters with EN50160 option.
27
PowerLogic ION7550 / ION7650

with WebMeterTM and MeterM@ilTM
Installation Guide
For further assistance please contact us at:
Schneider Electric
Power Monitoring and Control 2195 Keating Cross Road Saanichton, BC Canada V8M 2A5 Tel: 1-250-652-7100 295 Tech Park Drive, Suite 100 Lavergne, TN 37086 USA Tel: 1-615-287-3400 Electropole (38 EQI) 31, rue Pierre Mends France F - 38050 Grenoble Cdex 9 Tel : + 33 (0) 4 76 57 60 60 Getting technical support: Contact your local Schneider Electric sales representative for assistance or go to the www.powerlogic.com website. PowerLogic, ION, ION Enterprise, MeterM@il, WebMeter and Modbus are either trademarks or registered trademarks of Schneider Electric in France, the USA and other countries. All other trademarks are property of their respective owners. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. 70002-0247-11 2008 Schneider Electric. All rights reserved. 11/2008

7550 7650 Installation Guide

Uploaded by

Copyright:

Available Formats

7550 7650 Installation Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

7550 7650 Installation Guide

Uploaded by

Copyright:

Available Formats

70002-0247-11 11/2008

PowerLogic ION7550 / ION7650

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Network Compatibility Notice for the Internal Modem

CSA: Certified to CAN/ Certified to CSA C22.2 No.1010-1 UL 3111

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

PowerLogic ION7550 / ION7650 Models

TRAN (transducer) Model

Integ. Display TRAN 5 MB memory 10 MB memory Up to 256 sampling rate

Ethernet RJ45 Ethernet Fiber Modem

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Before You Begin

Phillips screwdriver Precision flat-head screwdriver Wire cutters / stripper

I/O Expansion Card

Form C Digital Outputs

Form A Digital Outputs

Front Panel Button Functions

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Basic Model Front View

Basic Model Side View

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Step 1: Mount the Meter

Meter Battery Considerations

Integrated Display Model

DIN 192 Cutout

Step 2: Wire the Ground Terminal

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Step 3: Wire the Digital I/O and Analog I/O

R11 R12 R13 R21

Form A Digital Outputs: Solid State Relays D1 - D4

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Internal Excitation Meter

130 VDC max

Digital Inputs (Meter Ordering Option): DI1 - DI8

Internal Excitation Meter

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Analog Inputs (Meter Ordering Option): AI1 to AI4

Example application: temperature sensing

Analog Outputs (Meter Ordering Option): AO1 to AO4

Signal Type Available Options Driving Capability

AO4 A03 A02 AO1

Accuracy Update Rate Latency Isolation to Ground

Example application: driving an analog meter with the DC current output

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

Step 4: Wire the Voltage and Current Inputs

Current Inputs: Class 20 Current Inputs (5A Option)

Current Inputs: Class 2 Current Inputs (1A Option)

2008 Schneider Electric. All rights reserved.

PowerLogic PowerLogic ION7550 / ION7650 Installation Guide

4-Wire Wye, 3-Element, Direct Connection Diagram

4-Wire Wye, 3-Element, 3 PTs Connection Diagram