Boq - Pani Bhaban

BILL OF QUANTITIES
Name of Project : Cyclone Shelter at Chaddaghar, Barguna.

CIVIL WORKS : FOUNDATION AND SUPER STRUCTURE
SL Rate in Figure and Works

NO. Description of Item Quantity Unit (To be Quoted) Quoted Amount
in figure in word in Taka
1 2 3 4 5 6 7
PILE WORK
1 BORED CAST IN SITU PILES
450 mm dia bored cast in-situ RCC pile of 18m max. length from cutoff level in foundation
works as per design and drawing with a concrete mix of 1:1.5:3 providing portland
cement, sand (FM 2.5) and 19mm down well graded approved best quality Bholagonj
shingles, erecting and placing necessary plants and equipments, placing reinforcement
case, provide required quantities of Bentonite, tools and tackles etc.
The concrete strength must obtain cylinder-crushing strength of 21 MPa (3000 Psi) at 28
days, which shall be determined from the materials at site by trial mix and sample test.
Actual length of service piles shall be determined and finalized after obtaining the Load
test result on test piles and if higher length of piles is required to be executed, no
enhancement of rates shall be entertained. Being the land is undulated and marshy to
some extent all necessary measures for execution of piles such as filling and leveling of
piling area with requisite compaction for moving the winch, machines and rigs and making
the area workable for setting pile layout and execution of pilling work shall have to be
taken at the own cost of Contractor and all the cost that shall be incurred against above
mentioned items shall be; inclusive of the quoted rates. The work will complete as per
direction of Engineer-in-charge. Two hundred
3700 cft 210.00 Ten only 777,000.00
The unit rate of pile is exclusive of cost of steel reinforcement and its fabrication). I he
payment shall be made for the length from TIP to cut-off level in the drawing. No payment
shall be made for extra boring from existing ground level to top level files. completed as
per direction of Engineer-in-charge.
2 BORING /DRILLING IN RCC PILE

Boring/drilling for cast in situ pile up to the required depth and diameter with minimum 6 m
long temporary steel casting, true to vertical, providing bentonite slurry and maintaining
water level in the hole, washing the hole for at least 30 8 minutes, clean the bore-hole
and make the bore-hole ready for placing steel cage and concreting including hire charge
of rig set with winch machine, tripod stand, trimle pipe, cost of fuel, lubricant, mobilization,
demobilization, maintenance, spares, stand-byes, insurance coverage, water, electricity & 2000 Ft 130.00 Taka one 260,000.00
other charges all complete as per direction of the Engineer-in-charge. hundred thirty
i) 450 mm dia only
3 REINFORCEMENT IN RCC PILE

Supplying, fabrication and fixing to details as per design deformed bar reinforcement in
concrete in accordance with BSTI standard in/c straightening and cleaning rust, if any,
bending & binding in position in/c supply of G.I. wires etc. complete in all respects in all
floors. The work complete as per direction of Engineer-in- charge.
Taka Sixty
thousand only
1 2 3 4 5 Taka6Sixty 7
60 Grade deformed bar with minumum fy=415Mpa ultimate strength 620 Mpa 12.00 Ton 60,000.00 thousand only 720,000.00
1,757,000.00
WORK UPTO GRADE BEAM
3 PILE HEAD BREAKING
Labour for breaking head of hardened cast in situ bored pile/pre-cast pile up to a
required length by any means but without damaging the rest and removing the dismantled 300 cft 130.00 Taka one 39,000.00
materials such as concrete to a safe distance including scraps and cleaning concrete
hundred thirty
from steel/M.S. rods, straightening & bending of pile bars, preparation and making
platform where necessary, carrying, all sorts of handling, stacking the same properly after only
clearing, leveling and dressing the situ and clearing the bed etc. complete as per direction
of the Engineer-in-charge. (Measurement will be given for the actual pile head volume to
be broken)
4 EARTHWORK
Earthwork in excavation in all kinds of soil for foundation trenches in/c. layout, providing
center lines, bench-mark pillars, leveling, ramming and preparing the base, fixing
bamboo spikes & giving layout with chalk powder, providing necessary tools and plants,
protecting and maintaining the trench dry etc., stacking the excavated earth at a safe
distance of up to 60 m lead, removing the spools etc. all complete as per direction of
Engineering-in-charge (rate is excluding the cost of bench mark pillars).
Excavation up to 1.50m depth and 60m lead including cheaking

levels and stacking the earth. 6000 cft 3.00 Taka Three only 18,000.00
5 DEWATERING FOR BASEMENT EXCAVATION

Arrangement of designed dewatering system for deep excavation at site shall be made
by the contractor to keep the base level of Basement dry and workable and to keep
watertable at least 1 metre below base level of excavation by sinking required number of
wells with pumps, IC1ying perforated strainer pipe horizontally to collect surface and
seepage water to a selected drainage line and to discharge the same to a selected
drainage system. To serve the purpose of dewatering, the contractor has to design and
develop the deep dewatering and drainage system at his own cost At the time of
designing and installing the system, the contractor will have to encounter the danger that
may arise out of the system works to adjoining buildings and necessary measures to
protect gradual sliding and horizontal movement of earth from underneath the foundation
of existing adjacent building shall be taken by the contractor. Any unexpected failure of
foundation of adjoining building caused due to dewatering and excavation shall fully be
protected by the Contractor at his own responsibility, arrangement and at their own cost.
If in any way failure occurs, Contractor will be fully held responsible for such failures and 1 L.S 10,000 Taka Ten 10,000.00
the damages to be made good and any compensation arisen out of such failure shall be thousand only
borne by the Contractor.
6 BRICK FLAT SOLING
1 2 3 4 5 6 7
Single brick flat soling including preparation of bed, sand filling (FM>=0.50), 10 leveling, Taka Twenty
dressing and sand blinding in foundation or floor with supply of all materials etc. complete 300 sft 25.00 Five only 7,500.00
as per direction of Engineer-in-charge.
7 CEMENT CONCRETE
Cement concrete work in leanest mix. 1:3:6 with sand of FM>=1.5, in foundation or floor
including breaking, screening, grading and washing aggregates with clear water, mixing, Taka One
laying in position, consolidation to levels, curing, including supply of all materials,
100.00 cft 160.00 hundred Sixty 16,000.00
excluding the cost of formworks etc. complete as per direction of Engineering-in-charge
only
9 RCC WORK UPTO GB

Reinforced cement concrete works of specified minimum-compressive strength fc = 21
Mpa (3000 Psi) for concrete at 28 days on standard cylinder, with Portland cement
conforming to BDS 232 & ASTM Standard, best quality coarse sand [Sylhet sand F.M.
2.5 to 2.8], 20 mm down well graded Bholaganj shinglesof proportion which actually is to
be determined by trial mix from approved materials including breaking chips and
screening through proper sieves, making, placing in position the centering shuttering,
making water-tight steel shuttering, placing of reinforcement in position; concrete mixing
in Batching Plant. casting in forms. compacting by vibrator machine and curing at least for
28 days, removing centering, shuttering, all complete including cost of water, electricity,
testing of materials and concrete & other charges as per direction of the Engineer-in-
charge.
Concrete shall be produced including necessary admixture: plasticizer, retarder etc. in the
Batching Plant and shall be transported to site by Transit Mixture Truck and placing shall
done by Concrete Pumps at site. The minimum cement content shall be 450 kg per cum
of concrete.
Rate is excluding the cost of reinforcement and its fabrication. But shall be inclusive of all
cost of production of concrete including necessary admixture : plasticizer, retarder etc. in
the Batching Plant, and Transportation of Concrete upto site and pouring of Concrete by
Pump at site
Upto Grade Beam 3,000.00 cft 260.00 780,000.00

3 REINFORCEMENT Upto GB
Supplying, fabrication and fixing to details as per design deformed bar reinforcement in
Taka Sixty
60 Grade deformed bar with minumum fy=415Mpa ultimate strength 620 Mpa 7.50 Ton 60,000.00 thousand only 450,000.00
1,320,500.00
WORK UPTO GROUND FLOOR ROOF
6 BRICK FLAT SOLING
Single brick flat soling including preparation of bed, sand filling (FM>=0.50), 10 leveling, Taka Twenty
dressing and sand blinding in foundation or floor with supply of all materials etc. complete 3,000.00 sft 25.00 Five only 75,000.00
as per direction of Engineer-in-charge.
1 2 3 4 5 6 7
7 CEMENT CONCRETE
Cement concrete work in leanest mix. 1:3:6 with sand of FM>=1.5, in foundation or floor
including breaking, screening, grading and washing aggregates with clear water, mixing, Taka One
laying in position, consolidation to levels, curing, including supply of all materials,
1,000.00 cft 160.00 hundred Sixty 160,000.00
excluding the cost of formworks etc. complete as per direction of Engineering-in-charge
only
8 DAMP PROOF MEMBRANE

Damp proof polythene membrane under cement concrete flooring in ground floor
providing 500 micron gauge polythene sheet laying including 150 mm over lapping in
joints and covering the vertical surfaces and to the surfaces of contact , with the concrete
etc. complete as per direction of Engineering-in-charge. all works complete.
3000 sft 4.00 Taka Four only 12,000.00
10 RCC WORK
2.5 to 2.8], 20 mm down well graded Bholaganj crushed stone chips of proportion which
actually is to be determined by trial mix from approved materials including breaking chips
and screening through proper sieves, making, placing in position the centering shuttering.
M.S. sheet, steel forms. 40 mm M.S. pipes, 50 x 40 mm adjustable pipes (jug pipes) with
150 x 150 x 6 mm base plate having pipe wall thickness 2.5 to 4.5 mm as props, making
water-tight steel shuttering, placing of reinforcement in position; concrete mixing in
Batching Plant. casting in forms. compacting by vibrator machine and curing at least for
charge.
of concrete.
Pump at site
Taka Two hundred
Seventy only
2500 cft 270.00 675,000.00
REINFORCEMENT IN RCC
11 Supplying, fabrication and fixing to details as per design deformed bar reinforcement in
Taka Sixty
12 60 Grade deformed bar with minumum fy=415Mpa ultimate strength 620 Mpa 10.00 Ton 60,000.00 thousand only 600,000.00
13 SAND FILLING
Sand filling in foundation trenches and plinth with coarse sand having min. F.M.
1 2 3 4 5 6 7
1.20 in 150mm layers including leveling, watering and consolidating each layer 10000 cft 18.00 Taka Eighteen 180,000.00
up to finished level (to be used when required as per design supplied by the
only
design office only) etc. all complete as per direction of the Engineer-in-Charge.
14 PATENT STONE WORK

Patent stone work in leanest mix. 1:2:4 with sand of FM>=1.5, in floor including breaking, Taka Two
screening, grading and washing aggregates with clear water, mixing, laying in position, 1200 cft 250.00 hunded Fifty only 300,000.00
consolidation to levels, curing, including supply of all materials etc. complete as per
direction of Engineering-in-charge
15 NCF WORK
NCF work in floor including mixing, laying in position, consolidation to levels, curing, 9000 sft 30.00 Taka Thirty only 270,000.00
including supply of all materials etc. complete as per direction of Engineering-in-charge
15 BRICK WORK
250 mm brick work with 1st class bricks in cement sand (F.M.1.2) mortar (1:4) and Taka Fifty Five
making bond with connected walls in/c necessary scaffolding, raking out joints, cleaning 600 cft 220.00 only 132,000.00
and soaking the bricks for at least 24 hours before use and washing of sand curing at
least for 7 days in all floors including cost of water, electricity & other charges etc. all
complete as per. direction of the Engineer-in-charge.
16 PLASTERING WORKS
16.1 PLASTER TO CONCRETE SURFACE
Minimum 6 mm thick cement sand (F.M. 1.2) plaster (1:4) with fresh cement (conforming Taka Twenty
to BDS 232) to ceiling R.C.C. columns, beams, surface of stair case, sunshades, 5,000.00 sft 25.00 Five only 125,000.00
cornices, railings, drop wall, louvers, fins and finishing the corners and edges in/c
washing of sand cleaning the surface, scaffolding and curing at least for 7 days, cost of
water, electricity & other charges etc. all complete in all respect as per drawing and
direction of the Engineer-in-charge.
16.2 PLASTER TO BRICK WALL SURFACE

Minimum 12 mm thick cement sand (F .M. 1.2) plaster (1 :6) with fresh cement Taka Twenty
(conforming to BDS 232) to ceiling R.C.C. columns, beams, surface of stair se, 1200 sft 27.00 Seven only 32,400.00
sunshades, cornices, railings, drop wall, louvers, fins and finishing the corners and edges
in/c washing of sand cleaning the surface, scaffolding and 11778 . ring at least for 7 days,
cost of water, electricity & other charges etc. all complete in all respect as per drawing
and direction of the Engineer-in-charge.
17 PAINTING WORKS
17.1 Plastic emulsion paint of approved best quality and colour delivered from authorized local
agent of the manufacturer in a sealed container, applying to wall and ceiling in two coats
over a coat of brand specified primer or sealer elapsing specified time for drying/recoating
including cleaning drying, making free from dirt, grease, was, removing all chalked &
sealed materials, fungus, mending good the surface defects, sand papering the surface 5000 sft 9.00 Taka Nine only 45,000.00
and necessary scaffolding, spreading by brush/roller/spray etc. all complete in all floor as
per direction of the Engineer-in-charge
1 2 3 4 5 6 7
17.3 Two costs of weather coat of approved quality colour and origin over a coat of plastron
sealer to exterior plastered surface necessary scaffolding and surface cleaning etc. all
complete in all floors complele as per direction of the Engineer-in-charge.
500.00 sft 11.00 Taka Eleven only 5,500.00
18 STAIR RAILING
900 mm high M.S.pipe railing in stairs including manufacturing and fixing in position as
per drawings, providing 62mm dia MS pipe hand rest and 38 mm verticals @ ± 1'-8" C/C
and 4 nos horizontal of 25mm dia MS pipe joining the verticals. The total railing framing
shall be manufactured by proper welding, the end of all verticals shall be embedded Taka Three
75mm into the concrete. welding and grinding of all joints shall be connected, grinded 60 sft 300.00 Hundred only 18,000.00
properly, polishing the pipes after finishing etc. all works complete as per direction of
Engineer-in-charge payment will be made only for clear height after finishing the stair.
2,629,900.00
WORK UPTO 1st FLOOR ROOF

10 RCC WORK
charge.
of concrete.
Pump at site
Taka Two hundred
Seventy only
2600 cft 270.00 702,000.00
Taka Sixty
thousand only
1 2 3 4 5 Taka6Sixty 7

15 NCF WORK
15 BRICK WORK
making bond with connected walls in/c necessary scaffolding, raking out joints, cleaning 4,000.00 sft 110.00 only 440,000.00
16 PLASTERING WORKS

(conforming to BDS 232) to ceiling R.C.C. columns, beams, surface of stair se, 9,000.00 sft 27.00 Seven only 243,000.00
17 PAINTING WORKS
17.2 Painting to door and window frames and shutters in two coats with approved best quality
1 2
Painting to door and window frames and shutters in two coats with approved best quality 3 4 5 6 7
and colour of synthetic enamel paint delivered from authorized local agent of the
manufacturer in a sealed container, having highly water resistant, high bondibilty, flexible,
using specific brand thinner applied by rass/roller/spray over a coat or priming elapsing
2000 sft 10.00 Taka Ten only 20,000.00
time for drying including surface cleaning from dust, oil or dirt, smoothening, finishing and
polishing with sand paper and necessary tools, scaffolding, testing charges etc. all
complete in all floors. The work complete as per direction of the Engineering-in-charge.
2,500.00 sft 11.00 Taka Eleven only 27,500.00
18 STAIR RAILING
19 DOOR FRAME WORKS

Supplying and making door and window frames (Chowkat) for all floors with matured
natural seasoned wood of required size including painting two coats of coal tar to the Taka Three
surface in contact with wall, fitting and fixing in position as per direction of the Engineer-
in-charge
13 nos 3,000.00 thousand only 39,000.00
20 WOODEN DOOR SHUTTER

Supplying, fitting and fixing 38 mm thick well matured, seasoned (min 10" wide plank)
solid wood single leaf door shutter having top rail style of sections 100 mm X 38 mm, lock
rail 125 X 38 mm and bottom rail 225 X 38 mm. Closed joints with 25 mm x 12 mm size
wooden peg and provided with best quality 4 Nos. 100 mm iron hinges 2 (two) Nos. best
quality 12 mm dia 300 mm and 200 mm long iron tower and socket bolts, 2 (two) Nos. Taka Three
heavy type nickel plated handle, hinged cleats, buffer blocks and finished by sand 150 sft 360.00 hundred Sixty 54,000.00
papering etc. in all floors as per direction of the Engineer-in-charge (All sizes of wood are only
finished).
21 STEEL DOOR
Steel door of any design in Penth House or wherever required made of mild steel
structural sections including 18 SWG M.S. sheet shutter, fabricating, welding, fitting, Taka Two
fixing, painting with 3 coats of synthetic enamel paint over a coat of anti-corrosive primer
110 sft 250.00 hundred Fifty 27,500.00
including supply and carriage of all materials, labour, tools, plants, etc. complete as per
drawing, decision and instruction of the Engineer-in-charge in all floors. only
22 ALLUMINIUM SLIDING WINDOW

Supplying, fitting and fixing of Aluminium sliding window as per standard specification
having 1.5 mm thick outer bottom (size 75.50 mm, 32 mm), 1.5 mm thick outer top (size
1 2 window as per standard specification
Supplying, fitting and fixing of Aluminium sliding 3 4 5 6 7
75.50 mm, 16.80 mm), 1.5 mm thick shutter top (size 33 mm. 26.80, 22 mm), 1 ,5 mm
thick shutter bottom (size 60 mm, 2.440 mm), 1.5 mm thick outer side (size 31 mm, 26
mm), 1.5 mm thick shutter lock (size 49.20 mm26.20 mm) & 1.5 mm 7 thick inter lock
(size 34.40 mm, 32.10 mm ) sections all Aluminium members (Total weight kg!sqm) will
be anodized to Aluminium Bronze/Silver color with a coat not less than 15 micron in Taka Two
thickness and density of 4 mg per square cm etc. including all accessories like sliding
door key lock, sliding door wheel, sliding door mohiar, sliding door neoprene, bolts & nuts 500 SFT 250.00 hundred Fifty 125,000.00
in!c sealants, keeping provision for fitting of ;; accessories, making grooves & ending only
good damages, carriage, and electricity. complete in all respect as per drawing and
23 M.S WINDOW GRILL

Supplying, fitting and fixing window grills made of 16 mm dia M.S. rod @ 100 mm c/c
fitted with 3(three) Nos. horizontal M.S. flat bar (38x6mm) including fabrication, welding, 500 sft 80.00 Taka Eighty only 40,000.00
riveting, cost of electricity, workshop charges, carriage, fixing with pre-placed clamps in
walls/RCC member for all floors etc. complete as per direction of Engineer-in-charge.
(total weight per sqm should be approx. 22.8 kg & add or deduct @ Tk. .04 for each kg 3,008,500.00
excess or less respectively).
WORK UPTO 2nd FLOOR ROOF

10 RCC WORK
charge.
of concrete.
Pump at site
Taka Two hundred
Seventy only
1 2 3 4 5 Taka Two6 hundred 7
Seventy only
2600 cft 270.00 702,000.00
Taka Sixty

15 NCF WORK
15 BRICK WORK
making bond with connected walls in/c necessary scaffolding, raking out joints, cleaning 4,000.00 sft 110.00 only 440,000.00
16 PLASTERING WORKS

(conforming to BDS 232) to ceiling R.C.C. columns, beams, surface of stair se, 9,000.00 sft 27.00 Seven only 243,000.00
17 PAINTING WORKS
NO. Plastic emulsion paint of approvedDescription of Item
best quality and colour delivered from authorized local Quantity Unit (To be Quoted) Quoted Amount
agent of the manufacturer in a sealed container, applying to wall and ceiling in two coats in figure in word in Taka
1 2
3 4 5 6 7
2000 sft 10.00 Taka Ten only 20,000.00
2,500.00 sft 11.00 Taka Eleven only 27,500.00
18 STAIR RAILING
19 DOOR FRAME WORKS

Supplying and making door and window frames (Chowkat) for all floors with matured
natural seasoned wood of required size including painting two coats of coal tar to the Taka Three
surface in contact with wall, fitting and fixing in position as per direction of the Engineer-
in-charge
13 nos 3,000.00 thousand only 39,000.00
20 WOODEN DOOR SHUTTER

Supplying, fitting and fixing 38 mm thick well matured, seasoned (min 10" wide plank)
solid wood single leaf door shutter having top rail style of sections 100 mm X 38 mm, lock
rail 125 X 38 mm and bottom rail 225 X 38 mm. Closed joints with 25 mm x 12 mm size
wooden peg and provided with best quality 4 Nos. 100 mm iron hinges 2 (two) Nos. best
quality 12 mm dia 300 mm and 200 mm long iron tower and socket bolts, 2 (two) Nos. Taka Three
heavy type nickel plated handle, hinged cleats, buffer blocks and finished by sand 150 sft 360.00 hundred Sixty 54,000.00
papering etc. in all floors as per direction of the Engineer-in-charge (All sizes of wood are only
finished).
21 STEEL DOOR
Steel door of any design in Penth House or wherever required made of mild steel in figure in word in Taka
1 structural sections including 18 SWG M.S. sheet
2 shutter, fabricating, welding, fitting, 3 4 5 Taka6 Two 7
22 ALLUMINIUM SLIDING WINDOW

Supplying, fitting and fixing of Aluminium sliding window as per standard specification
75.50 mm, 16.80 mm), 1.5 mm thick shutter top (size 33 mm. 26.80, 22 mm), 1 ,5 mm
thick shutter bottom (size 60 mm, 2.440 mm), 1.5 mm thick outer side (size 31 mm, 26
mm), 1.5 mm thick shutter lock (size 49.20 mm26.20 mm) & 1.5 mm 7 thick inter lock
(size 34.40 mm, 32.10 mm ) sections all Aluminium members (Total weight kg!sqm) will
be anodized to Aluminium Bronze/Silver color with a coat not less than 15 micron in Taka Two
thickness and density of 4 mg per square cm etc. including all accessories like sliding
door key lock, sliding door wheel, sliding door mohiar, sliding door neoprene, bolts & nuts 500 SFT 250.00 hundred Fifty 125,000.00
in!c sealants, keeping provision for fitting of ;; accessories, making grooves & ending only
good damages, carriage, and electricity. complete in all respect as per drawing and
23 M.S WINDOW GRILL

Supplying, fitting and fixing window grills made of 16 mm dia M.S. rod @ 100 mm c/c
fitted with 3(three) Nos. horizontal M.S. flat bar (38x6mm) including fabrication, welding, Taka Eighty only
riveting, cost of electricity, workshop charges, carriage, fixing with pre-placed clamps in
walls/RCC member for all floors etc. complete as per direction of Engineer-in-charge.
500 sft 80.00 40,000.00
(total weight per sqm should be approx. 22.8 kg & add or deduct @ Tk. .04 for each kg
excess or less respectively).
3,008,500.00
ROOF TOP WORK

10 RCC WORK
charge.
1 2 3 4 5 6 7
of concrete.
Pump at site
Taka Two hundred
Seventy only
500.00 cft 270.00 135,000.00
Taka Sixty
15 LCC WORK
LCC work in floor including mixing, laying in position, consolidation to levels, curing, 2500 sft 40.00 Taka Forty only 100,000.00
15 BRICK WORK
making bond with connected walls in/c necessary scaffolding, raking out joints, cleaning 600 sft 110.00 only 66,000.00
16 PLASTERING WORKS
to BDS 232) to ceiling R.C.C. columns, beams, surface of stair case, sunshades, 5000 sft 25.00 Five only 125,000.00

(conforming to BDS 232) to ceiling R.C.C. columns, beams, surface of stair se, 1200 sft 27.00 Seven only 32,400.00
17 PAINTING WORKS
Plastic emulsion paint of approved best quality and colour delivered from authorized local in figure in word in Taka
1 agent of the manufacturer in a sealed container,
2 applying to wall and ceiling in two coats 3 4 5 6 7
800 sft 10.00 Taka Ten only 8,000.00
500.00 sft 11.00 Taka Eleven only 5,500.00
21 STEEL DOOR
667,400.00
25 SITE CLEANING
Cleaning the work site after completion of works and demobilization of contractor's men,
materials, equivalent etc. including washing and clearing of floors, sote and touch up work Taka Fifty
required before work handover of the building/project complete as per direction of the
1 L.S 50,000 thousand only 50,000.00
Engineer-in-charge.
2500+2600+2600+500
10+11+11+2
8800
16000
24000
28000
12000
150
SECTIOPN - 6 : BILL OF QUANTITIES
PART- B2 : SANITARY, WATER SUPPLY & PLUMBING WORKS
1 2 3 4 5 6 7
1.0 UPVC PIPE AND PIPE FITTINGS
Supply, fitting and fixing of Extra heavy uPVC pipe shall be made uPVC as per
BS4514/18044221 88213 standard. Pipe shall be bell end socket type. Approved type
of solvent cement/sealant shall be used to install pipe and jointing the pipe with pipe
fittings. Joint shall be watertight. In brick wall pipe shall be surrounded by concrete in 1:
3.5: 5.5 and shall be clamped to wall properly at an interval of not more than 1200 mm.
Pipe laying shall have the following gradient unless otherwise specified. Nominal dia of
pipe with thickness shall be as follows. The pipes shall be Hf (HAN f ING) National
Polymer industries from Bangladesh and pipe fitting shall be imported from Singapore.
1.1 UPVC PIPE

Supply, fitting, fixing of bell and spigot type extra heavy uPVC pipe as per direction and
drawing. The pipes shall be H4> (HAN 4> ING) National Polymer industries from
Bangladesh
a) 300 mm dia 300 Rm 2,400.00 Taka two 720,000.00

thousand four
hundred only
b) 250 mm dia 350 Rm 1,825.00 Taka One thousand 638,750.00
eight hundred
twenty five only
c) 200 mm dia 500 Rm 975.00 Taka Nine 487,500.00

hundred seventy
five only
d) 150 mm dia 800 Rm 550.00 Taka Five 440,000.00
hundred fifty only
e) 100 mm dia 1000 Rm 300.00 Taka three 300,000.00

hundred only
f) 80 mm dia 50 Rm 200.00 Taka two hundred 10,000.00

only
g) 50 mm dia 200 Rm 110.00 Taka One 22,000.00
hundred ten only
h) 40 mm dia 150 Rm 85.00 Taka eighty five 12,750.00
only
1 2 3 4 5 6 7
1.2 UPVC T - JOINT

Supply, fitting, fixing of extra heavy UPVC standard Door AT-joint, as per direct
drawing. All pipe fitting shall be imported from Singapore.
a) 200 mm x 200 mm x 150 mm dia 10 each 4,540.00 Taka Four thousand 45,400.00
five hundred forty
only
b) 150 mm x 150 mm x 150 mm dia 20 Each 1,590.00 Taka One thousand 31,800.00
five hundred ninety
only
c) 150 mm x 150 mm x 100 mm dia 60 Each 1,750.00 Taka One thousand 105,000.00
seven hundred fifty
only
d) 100 mm x 100 mm x 100 mm dia 150 Each 550.00 Taka Five 82,500.00
hundred fifty only
e) 100 mm x 100 mm x 100 mm x 100 mm dia 10 Each 950.00 Taka nine 9,500.00
hundred fifty only
f) 100 mm x 100 mm x 80 mm dia 2 Each 550.00 Taka Five 1,100.00

hundred fifty only
g) 100 mm x 100 mm x 50 mm dia 50 Each 550.00 Taka Five 27,500.00

hundred fifty only
1.3 UPVC Y - JOINT

Supply, fitting, fixing of extra heavy UPVC standard Y joint, as per direction & drawing.
a) 150 mm x 150 mm x 150 mm dia 10 each 1,870.00 Taka One thousand 18,700.00
eight hundred
seventy only
b) 150 mm x 150 mm x 100 mm dia 50 Each 1,370.00 Taka One thousand 68,500.00
three hundred
seventy only
c) 100 mm x 100 mm x 100 mm dia 10 Each 1,000.00 Taka One thousand 10,000.00
only
1 2 3 4 5 6 7
d) 100 mm x 100 mm x 100 mm x 100 mm dia 2 Each 1,200.00 Taka One thousand 2,400.00
two hundred only
1.4 UPVC - TRAP

a) P - TRAP
Supply, fitting, fixing of 100 mm dia UPVC trap Syphon trap of P-trap including making Taka seven
holes in wall of floor and mending good the damage upto the satisfaction. 142 Each 700 hundred only 99,400.00
b) S - TRAP
Supply, fitting, fixing of 100 mm dia UPVC trap Syphon trap of S-trap including making
holes in wall of floor and mending good the damage upto the satisfaction. 5 Each 660 Taka six hundred 3,300.00
1.5 UPVC BEND sixty only
Supply, fitting, fixing of 100 mm dia UPVC Deep Bend / Normal Bend including making
holes in wall of floor and mending good the damage upto the satisfaction.
a) Bend 200 mm dia 10 each 2,870.00 Taka Two thousand 28,700.00

eight hundred
seventy only
b) Long Bend 150 mm dia 50 each 920.00 Taka nine hundred 46,000.00
twenty only
c) Short Bend 150 mm dia 20 each 800.00 Taka Eight hundred 16,000.00
only
d) Short Bend 100 mm dia 150 each 350.00 Taka Three 52,500.00
hundred fifty only
e) Short Bend 100 mm dia 50 each 270.00 Taka Two hundred 13,500.00
seventy only
f) Long Bend 80 mm dia 10 each 260.00 Taka Two hundred 2,600.00
sixty only
f) Long Bend 50 mm dia 120 each 220.00 Taka Two hundred 26,400.00
twenty only
1.6 UPVC LOOSE SOCKET
Supply, fitting, fixing of UPVC Loose Socket as per Drawing and Direction .
a) 150 mm Dia 50 each 430.00 Taka Four hundred 21,500.00
thirty only
b) 100 mm dia 20 each 150.00 Taka One hundred 3,000.00
fifty only
1 2 3 4 5 6 7
1.7 UPVC OFFSET BEND

Supply, fitting, fixing of 100mm dia UPVC Offset Band as per Drawing and Direction .
a) 200 mm Dia 2 each 4,300.00 Taka Four thousand 8,600.00
three hundred only
b) 150 mm dia 15 each 1,070.00 Taka One thousand 16,050.00

seventy only
c) 100 mm dia 15 each 500.00 Taka Five 7,500.00

hundred only
1.8 UPVC VENT Cowl
Supply, fitting, fixing of UPVC Vent Cowl as per Drawing and Direction .
a) 150 mm Dia 20 each 360.00 Taka Three 7,200.00
hundred sixty only
b) 100 mm dia 10 each 130.00 Taka One 1,300.00

hundred thirty only
1.9 UPVC Clean Out Cup / service Door

Supply, fitting, fixing of UPVC End cup as per drawing and direction
a) 150 mm Dia 10 each 800.00 Taka Eight 8,000.00
hundred only
b) 100 mm dia 20 each 400.00 Taka Four 8,000.00
hundred only
2.0 G.I. PIPE
Supply, fitting, fixing of GI pipe of National Tube Product. Pipe work shall be complete
with bends, tees, elbows, socket, union, reducers, hanger, bracket, clamp etc.
receptively complete as per drawing and direction of the Engineer-in- charge. Approved
type of sealant shall be used. Pipe work shall be suitable to
withstand a hydraulic pressure test of 100 psig and 48 hours 80 psig stand pressure all
GI pipe layout area. All GI materials used in pipe work shall be painted with two coats of
read oxide prime cote of approved quality.
a) 100 mm dia 200 Rm 2,500.00 Taka Two 500,000.00

thousand five
hundred only
in figure in word
Taka Two in Taka
1 2 3 4 5 thousand
6 five 7
hundred only
b) 80 mm dia 200 Rm 1,620.00 Taka One thousand 324,000.00
six hundred twenty
only
c) 65 mm dia 100 Rm 1,620.00 Taka One thousand 162,000.00

six hundred twenty
only
d) 50 mm dia 200 Rm 890.00 Taka Eight hundred 178,000.00

ninety only
e) 40 mm dia 150 Rm 650.00 Taka Six hundred 97,500.00
fity only
f) 32 mm dia 50 Rm 650.00 Taka Six hundred 32,500.00
fity only
g) 25 mm dia 200 Rm 480.00 Taka Four hundred 96,000.00
eighty only
h) 20 mm dia 150 Rm 325.00 Taka Three 48,750.00
hundred twenty five
only
i) 13 mm dia 2000 Rm 270.00 Taka Two hundred 540,000.00
seventy only
3.0 COPPER PIPE
Supply, fitting, fixing of Copper pipe work shall be complete with bends, tees, elbows,
socket, union, reducers, hanger, bracket, clamp etc. receptively complete as per
drawing and direction of the Engineer-in-charge. Approved type of sealant shall be
used. Pipe work shall be suitable to withstand a hydraulic pressure test of 100 psig and
48 hours 80 psig stand pressure all pipe layout area. All cupper pipe hot water supply
used in the pipe. Hot water pipe including 40mm or 25mm insulation cover work shall be
of approved quality.
Taka One thousand
a) 20 mm dia 50 Rm 1,000.00 only 50,000.00
b) 13 mm dia 50 Rm 950.00 Taka Nine hundred 47,500.00

fity only
4.0 TOILET FITTINGS & FIXTURES
Supply, fitting and fixing Bathroom fittings in toilets including carrying up the fixtures to
different parts of the building all respectively complete as per drawing and direction of
the Engineer-in-charge.
4.1 STOP COCK
Supply, fitting and fixing CP Stop Cock of dia 13 mm with brass rising stem screwed
bonnet, screwed end type. Stop cock shall be capable to withstand a pressure of 344
kPa. and sha location shown in the drawing and as per direction of Engineer-in-charge.
Product shall be Made B Model American Standard, Thailand or equivalent of COTTO,
1 Supply, fitting and fixing CP Stop Cock of 2dia 13 mm with brass rising stem screwed 3 4 5 6 7
bonnet, screwed end type. Stop cock shall be capable to withstand a pressure of 344 Taka Eight
kPa. and sha location shown in the drawing and as per direction of Engineer-in-charge.
Product shall be Made B Model American Standard, Thailand or equivalent of COTTO,
28 Each 800.00 hundred only 22,400.00
Thailand.
4.2 ANGLE STOP COCK

Supply, fitting and fixing of CP oval type Angle Stop Cock of dia 13 mm with bracing Taka Five
screwed bonnet, solid wedge and screwed end type. Angle Stop cock shall be suitable 220 Each 510.00 hundred ten only 112,200.00
a pressure of 344 KPa. and shall be installed at location shown in the drawing and c of
the Engineer-in-charge. Product shall be Model No.A-4400 of American standard
equivalent Model of COTTO, Thailand.
4.3 WC Shower Rose (Push shower)

Supply, fitting, fixing WC Shower Rose with stem screwed bonnet, disc and screwed Taka Five
end type. WC Shower Rose shall be installed at location shown in the drawing and as 80 Each 570.00 hundred seventy 45,600.00
per direction of Engineer-in-charge. Threaded joint shall be made properly sealed. only
Product shall be Model No. A-4800 of American Standard,
Thailand or equivalent model of COTTO, Thailand.
4.4 OPEN TAP / BIB COCK

Supply, fitting and fixing of 13 mm dia CP Open Tap shall be constructed with bronze
and shall have rising stem screwed bonnet, disc. and screwed end type and and shall Taka Six
be suitable to withstand a pressure of 344 kPa. Open taps/Bip cocks shall be installed
at location shown in the drawing and as per direction of the engineer-in-charge.
80 Each 630.00 hundred thirty only 50,400.00
Threaded joint shall be made properly sealed. Product shall be Model No. A-4100-980-
593 of American standard, Thailand or equivalent model of COTTO, Thailand
4.5 BASIN PILLAR COCK

Supply, fitting and fixing of 13 mm dia CP Medal Headed Heavy deluxe body Basin
Pillar Cock shall be constructed with brass rising stem screwed bonnet, solid wedge Taka Five
and screwed end type and shall be suitable to withstand a pressure of 344 KPa. Pill
cock shall be installed at location shown in the drawing and as per direction of the
85 Each 570.00 hundred seventy 48,450.00
Engineer-in-charge. Product shall be Model No.A-4000-980-584 of American standard, only
4.6 BASIN MIXTURE

Supply, fitting fixing of 13 mm dia CP Basin Mixture shall be constructed with brass
rising stem screwed bonnet, solid wedge and screwed end type. Valves shall be
capable to withstand a pressure of 344 KPa. Basin mixture shall be installed at location
shown in the drawing and as per direction of the Engineer-in-charge. Product shall be
1 2 Mixture shall be constructed with brass
Supply, fitting fixing of 13 mm dia CP Basin 3 4 5 6 7
rising stem screwed bonnet, solid wedge and screwed end type. Valves shall be Taka One
capable to withstand a pressure of 344 KPa. Basin mixture shall be installed at location
shown in the drawing and as per direction of the Engineer-in-charge. Product shall be
28 Set 1,860.00 thousand eight 52,080.00
model no A-1900-976-100B of American Standard Thailand or 1211.101.50 American hundred sixty only
Standard Thailand or equivalent model of COTTO, Thailand.
4.7 SINK COCK

Supply, fitting and fixing of 13 mm dia CP Sink Cock shall be constructed with brass
rising stem (Nozzle type), solid wedge and screwed end type. Valves shall be capable Taka One
to withstand a pressure of 344 kPa. Sink cock shall be installed at location shown in the
drawing and as per direction of the Engineer-in-charge. Product shall be Model No. A-
10 Each 1,380.00 thousand threet 13,800.00
4050.980-590 of American Standard, Thailand or equivalent model of COTTO, Thailand hundred eighty
only
4.8 BOTTLE TRAP

Supply, fitting and fixing of CP Bottle Trap shall be constructed with bronze and shall
have 32 mm dia inlet and outlet steel pipe connector complete with adjusting sockets, Taka seven
washer etc. The Trap shall have bottom opening screwed end type cleaning
130 Each 780.00 hundred eighty 101,400.00
arrangement. Bottle Trap shall be installed at location shown in the drawing and as per
direction of the Engineer-in-charge. Threaded joint shall be made properly seated. only
Product shall be Model No. A-8102 of American Standard, Thailand) or equivalent
model of COTTO. Thailand.
4.9 WASHING HAND BASIN

Supply. fitting and fixing of super vitreous washing hand basin super and fitting fixing
the same in position with heavy type CI wall brackets, 32 mm dia CP basin waste,
including making holes in walls and fitting with CI wall brackets and mending good the
damages etc. complete as per direction of the Engineer-in-charge.
a) Product shall be Model No. basin TF-956 with Pedestal Model-900P American Taka Two thousand
Standard, Thailand or equivalent model of COTTO, Thailand. 85 Each 2500 five hundred only 212,500.00
b) Product shall be Model No. Basin TF-0409 / 0076 of American standard, Taka Three thousand
Thailand or equivalent model of COTTO, Thailand 28 Each 3000 only 84,000.00
4.10 SINK (SINGLE BOWL)

Supply, fitting and fixing of super quality Stainless Steel Sink in position shown in the
drawing with heavy of 3 '-6" x 1'-8" size type CI wall brackets, 32 mm dia CP basin
waste, including making holes in wall and fitting with CI wall brackets and mendin good
the damages etc, complete as per direction of the Engineer-in-charge. Produc shall be
1 2
Supply, fitting and fixing of super quality Stainless Steel Sink in position shown in the 3 4 5 6 7
drawing with heavy of 3 '-6" x 1'-8" size type CI wall brackets, 32 mm dia CP basin 10 Each 3,100.00 Taka Three thousand 31,000.00
waste, including making holes in wall and fitting with CI wall brackets and mendin good one hundred only
the damages etc, complete as per direction of the Engineer-in-charge. Produc shall be
of 'TEKA' Brand of Spain or equivalent foreign Brand.
4.11 FLEXIBLE CONNECTION

Supply, fitting and fixing of flexible connecting pipe of 13 mm dia and 460 mm length
shall be complete with SS flare nut and socket on both end to adapt 13 mm dia 220 Each 150.00 Taka one 33,000.00
threaded G.I Pipe. Product shall be Model No. A-110333 of American Standard,
hundred fifty only
4.12 Commode (Combi)

Supply, fitting and fixing porcelain commode 'P' or'S' type trap, with ebonite (heavy
type) socket etc. preparing the base with cement concrete and wire net or rod if
necessary in all floors including making holes wherever required and mending good the
damages, fitting, fixing with all necessary fittings and connection as per direction of the
Engineer-in-charge. Commode shall be complete with 12 Liter capacity wall mounted
Cistern and auto flashing system (Push Type).
Taka nine
a) Commode with seat cover including all internal fittings. The product shall be thousand eight
Model no. TF-2177 of American Standard, Thailand of equivalent model of 55 Set 9800 hundred only 539,000.00
COTTO, Thailand
b) Commode with seat cover include all internal fittings. The product shall be Taka Eleven
Model no. TF-2175 of American Standard, Thailand or equivalent of COTTO 28 Set 11,200.00 thousand two 313,600.00
Thailand.
hundred only
4.13 SQUAT (LONG PAN)

Supply, fitting and fixing of Orissya type Squatting pan Model TF-100FPfT of American
Standard, Thailand or equivalent COTTO, Thailand with foot rest and preparing the
base of pan in cement concrete wire net or roads if necessary in all floors where
necessary and mending good the damages, complete with tank as per drawing and
Taka Two
direction of the Engineer-in-charge. The product shall be Model No. TF-100FPfT of 2 Set 2,200.00 thousand two 4,400.00
American Standard, Thailand or equivalent Model of COTTO, Thailand hundred only
4.14 URINAL
Supply, fitting and fixing of supper vitreous porcelain standing urinal with heavy type CI
wall bracket 32 mm dia CP waste pipe wherever required in/c making hole in wall and
1 2 3 4 5 6 7
wall bracket 32 mm dia CP waste pipe wherever required in/c making hole in wall and
fitting with CI wall bracket and mending good the damages etc. all complete as per
drawing and direction of the Engineer-in-charge.
a) Standing Urinal Model No- TF 6789 tanding Urinal of American Standard, Thailand or Taka one
equivalent model of COTTO. thousand nine
33 set 1,950.00 hundred fifty only 64,350.00
b) Sqyating Urinal Locally made best quality Taka one
thousand five
10 set 1,560.00 hundred sixty only 15,600.00
4.15 AUTOMATIC URINAL FLASH
Supply, fitting and fixing of infrared sensored Automatic Urinal Flash with 2-step system Taka Two
of pre-flashing and main flushing and capable of automatically activating hen the user 33 Set 2,800.00 Thousand eight 92,400.00
comes and leaves the sensing range: Model no.108 (AC) of Solomon, Taiwan or
equivalent model from manufacturers of Thailand/Singapore/Japan.
hundred only
4.16 SHOWER ASSEMBLY

Supply, fitting and fixing of C.P. Shower Assembly complete with all standard
accessories and fittings. Shower assembly shall be fitted to pipe end by using approved taka Nine
sealing compound to make the joint water tight as per drawing and direction of the
Engineer-in-charge. Product shall be of Model No-A-6070 Moving
28 Set 950.00 hundred fifty only 26,600.00
Shower with arm. of American Standard, Thailand or equivalent model of COTTO,
Thailand.
4.17 SHOWER TRAY

Square type Shower tray, shower mixture, shower head, shower hose, shower tub filler Taka six
including all The product shall be Model No. TF-7330, A-3900-976-400, A-6110-978- 28 Set 6,500.00 thousand five 182,000.00
780, A-900-709 of American Standard, Thailand or equivalent model From
Thailand/USA.
hundred only
4.18 GLASS MIRROR

a) Supplying and installation of bevelled edge plate glass mirror (800 mm x 750 mm
size) fitted in wall with screws including plastic plug, damp protection on back etc. all Taka one
complete as per direction of the Engineer-in-charge. Product shall be of Model: No.-
Caro-LV-01 of American Standard, Thailand or equivalent model of COTTO, Thailand.
28 Each 1,930.00 thousand nine 54,040.00
hundred thirty
only
b) Supplying and installation of locally made best quality bevelled edge plate glass mm Taka One
x 750 mm size) fitted in wall with screws including plastic plug, damp protection etc. all 85 Each 1,560.00 thousand five 132,600.00
complete as per direction of the Engineer-in-charge
hundred sixty only
4.19 TOWEL BAR AND RACK
Supply, fitting, fixing of CP towel bar respectively complete with CP wall bracket fitted
on wall plastic plug and screws as per drawing and direction of the Engineer-in-charge.
1 2
Supply, fitting, fixing of CP towel bar respectively complete with CP wall bracket fitted 3 4 5 6 7
on wall plastic plug and screws as per drawing and direction of the Engineer-in-charge.
a) Size: 610 mm x 25 mm Model No. TF-9485 Towel bar of American standard, Taka Four
Thailand or equivalent model of COTTO, Thailand. hundred thirty
60 set 435.00 five only 26,100.00
b) Round Ring, Model No. TF-9332 Towel Ring of American standard, Thailand Taka Three
Ir equivalent model of COTTO, Thailand. hundred thirty
30 set 335.00 Five only 10,050.00
C) Cort Hook American standard or equivalent model of Thailand Taka Two

hundred eighty
28 set 280.00 only 7,840.00
4.20 C. P Soap Case
Supply, fitting, fixing of CP Soap Case with counter sunk screws etc. complete. Soap Taka
case shall be fixed at location shown in the drawing and as per direction of the 150 set 260.00 Two hundred 39,000.00
Engineer-in-charge. Product shall be Model No- TF 9401 of American Standard,
sixty only
4.21 Toilet Paper Holder

Supply, fitting, fixing of CP brass toilet paper holder complete with CP brass bracket. Taka Two
Paper holder shall be fixed to the wall by using plastic bolt and screws and as per 85 set 210.00 hundred ten 17,850.00
direction of the Engineer-in-charge. Product shall be Model No- TF 9411 paper Holder
of American Standard, Thailand or equivalent model of COTTO, Thailand.
only
4.22 UPVC STRAINER

Supply, fitting, fixing of 100 mm dia uPVC Strainer complete with all accessories,
colour should be matched with colours of floor tiles and approved by the Engineer-in-
charge.
a) 100mm dia 3 Piece Strainer (with cover) Taka Four hundred

twenty five only
120 Each 425.00 51,000.00
b) 100mm dia 2 Piece Strainer Taka Four hundred
only
20 Each 400.00 8,000.00
c) 150 mm dia Roof Rain Strainer Taka Five hundred
20 Each 500.00 only 10,000.00
d) 100 mm dia Roof Rain Strainer Taka Three
hundred sixty only
d) 100 mm dia Roof Rain Strainer in figure in word
Taka Three in Taka
1 2 3 4 5 hundred 6sixty only 7
40 Set 360.00 14,400.00
5.0 Automatic Soap dispenser
Supply, fitting, fixing of Automatic Liquid Soap Dispenser with Battery-Operated system, Taka Two
screws etc. complete, as per drawing and direction of the Engineer-in-charge. Product 28 set 2,500.00 thousand five 70,000.00
shall be Model No-9309 (Solomon, Taiwan) or equivalent model from hundred only
Thailand/Singapore/Japan.
6.0 Automatic Head Dryer

Supply, fitting, fixing of Automatic Hand Dryer with' AC-Operated system complete as er Taka Six
drawing and direction of the Engineer-in-charge. Product shall be Model No-HD-103 28 set 6,700.00 thousand seven 187,600.00
Solomon, Taiwan or equivalent model from Thailand/Singapore/Japan. hundred only
7.0 Automatic Water Heater

Supply, fitting and fixing of Electric water heater shall be made of Stainless Steel-13
WG inner tank container with seamless welding pressure tested to leaks complete as
per drawing and direction of the Engineer-in-charge. Outside jackets shall be prayed
with scratch and Stainless Steel high gloss backed enamel paint. The heater shall be
complete with adjustable Thermostat (30°C to 80°C) and automatic pressure release
valve and all other required accessories. The water heaters Product shall be IEGA"
Brand for SHAMEEM & COMPANY from Bangladesh.
a) 10 Gallon Capacity Taka Fifteen

thousand six
12 Set 15,600.00 hundred only 187,200.00
b) 15 Gallon Capacity
Taka Eighteen
thousand only
12 Set 18,000.00 216,000.00
8.0 RCC Pipe
Supply, fitting, fixing and laying 200 mm and 150 mm dia R.C.C pipe over 100 mm and
75 mm thick cement concrete (6:3:1) at base over a brick flat soling with proper gradient
in trenches, making collar joints with gasket and cement mortar (1:1) including cutting
trenches and refilling the same upto the required depth as per drawing and direction of
a) 400 mm dia pipe Taka One thousand

one hundred
100 Rm 1,125.00 twenty five only 112,500.00
b) 300 mm dia pipe
Taka Eight hundred
20 Rm 875.00 seventy five only 17,500.00
9.0 CATCH PIT
1 2 3 4 5 6 7
Construction of masonry Catch pits, inside measurement (600 mm x 600 mm x 600 Taka Four
mm) with 250 mm thick brick work in cement mortar (4:1) and 100 mm thick R.C.C top 40 Each 4,400.00 thousand four 176,000.00
(4:2:1) with necessary reinforcement with top MS Grating system as per drawing and
hundred only
10.0 INSPECTION PIT

a) Construction of masonry Inspection pits, inside measurement (600 mm x 600 mm x Taka Five
760 mm) with 250 mm thick brick work in cement mortar (4:1) and 100 mm thick R.C.C 50 Each 5,600.00 thousand six 280,000.00
top (4:2:1) with necessary reinforcement as per drawing and direction of Engineer-in-
charge.
hundred only
b) Construction of masonry Inspection pits, inside measurement (760 mm x 900 mm x Taka seven
1000 mm) with 250 mm thick brick work in cement mortar (4:1) and 100 mm thick R.C.C 35 Each 7,500.00 thousand five 262,500.00
top (4:2: 1) with necessary reinforcement as per drawing and direction Engineer-in-
charge.
hundred only
11.0 C.I COVER

Supply and installation of heavy duty C.I. manhole covers of 550 mm clear opening with Taka one
frames (Minimum weight of cover to be 15 Kg) in top slab of inspection pits all complete 70 Each 1,200.00 thousand two 84,000.00
as per drawings and direction of the Engineer-in-charge.
hundred only
12.0 SEPTIC TANK

Construction of Septic Tank of different sizes with brick work/ RCC work in cement
mortar (1 :6) as per approved drawings over a brick flat soling and 150 mm thick
cement concrete flooring ( 1:2:4) with 125 mm thick walls in partition and 20mm thick
cement plaster (1:4) to insides of walls with N.C.F. and 25mm thick patent stone (1:2:4)
flooring with N.C.F. including supplying fitting and fixing of two R.C.C. Tees and
providing 500mm dia water sealed heavy type C.I. manhole cover with locking Taka Four
arrangement and 100 mm thick R.C.C (1:2:4) Top slab with minimum 1% reinforcement 2 Each 430,000.00 hundred thirty 860,000.00
including centering, shuttering, fabricating, casting and curing etc. complete, upto
required depth including necessary earth work in excavation and shorting, bailing out thousand only
water and side filing including the cost of all materials, operations and incidental
charges, etc. all complete as per drawing and direction of Engineer-in-charge
A) 250 Users Septic Tank
13.0 SOAK WALL

1 2 3 4 5 6 7
Construction of Soak Well of different sizes with 250 mm thick solid brick work and 250
mm honey comb brick work with cement mortar (1 :6) as per design and drawings over
R.C.C (1:2:4) well curb with 1.5% reinforcement including supplying and fixing 500mm
dia water sealed heavy type C.I. manhole cover with locking arrangement filling the well
Taka Three
upto the required depth with graded khoa and sand including supplying and fabricating 4 Each 310,000.00 hundred ten 1,240,000.00
M.S. Rod casting curing including necessary earth work in excavation, side filling and thousand only
bailing out water including cost of all materials etc. all complete as per drawing, design
and direction of the Engineer-in-Charge.
a) 250 Users Soak Well
14.0 PVC WATER TANK

Supply fitting and fixing of best quality PVC WATER TANK capacity 3,000 litter Taka Thirty six
including all fittings and accessories etc. all complete as per direction of the Engineer- 4 Each 36,000.00 thousand only 144,000.00
in-charge. Tank shall be Gazi or Polycon Brand.
15.0 PRESSURISED WATER DISTRIBUTION SYSTEM

Supply, installation, testing & commissioning of hydro-pneumatics system comprising of
following items complete in all respect as per direction of the Engineer-in-charge. All the
pumps, component and accessories for the system shall be from
USA/UK/Japan/Australia.
a) 3 Nos. vertical in line pumps complete in respect with heavy duty cast iron
conforming to BS 1452, closed coupled centrifugal, Impeller shall be manufactured in
gun-metal.
Taka Three
Pump Capacity : 500 GPM 2 Set 350,000.00 hundred fifty 700,000.00
Head required : 90 Meter thousand only
RMP : 2900
b) Accessories like isolating gate valve, on-return valves, and Interconnecting pipe work
complete in all respect.
Electrical Control Panel with logic controller relays. Pressure switch, pressure Gauge,
Hand/Off/Auto switch, pump starter's duty selector switch, wiring cabling from panel to
pumps, level controller, Power on light, run & trip, main isolator switch, terminal blocks
suitable for field services interlocks complete with all
accessories as per manufacturer specification.
1 2 3 4 5 6 7
c) 1 No x 500 litre vessel with inner changeable butyl rubber membrane. Base
frame: All components mild steel 7 hollow section frame & shall be primed & painted
with protective undercoat & gloss finish.
16.0 SUMP PUMP

Supply, installation, testing and commissioning of single stage Sump pump having a Taka forty
capacity to handle 40 Gpm of water against a head of 15 meter of wg. Product shall be 6 Set 40,000.00 thousand only 240,000.00
from USA / UK/JAPAN/ Germany/Australia/Italy.
17.0 SLUDGE PUMP

Supply, installation, testing and commissioning of single stage Sludge pump having a Taka fifty
capacity to handle 45 Gpm of water against a head of 30 meter of wg. Product shall be 2 Set 50,000.00 thousand only 100,000.00
from USA/UK/JAPAN/Germany/Australia.
18.0 VALVES & FITTINGS

Supply and installation of valves and fittings shall be capable to withstand a pressure of
200 psig. Valves of 80 mm & 100 mm dia shall be flanged end type complete with
companion flanges, gasket etc. and valves of 40mm dia shall be of threaded end type.
Valves shall be installed at location shown in the drawing and as per direction of
Engineer-in-charge. Product shall be from UK/JAPANI Germany/ Australia/Italy .
18.1 GATE VALVES

Supply, fitting and fixing of Gate valves upto 40 mm dia of bronze body and valves
above 40 mm dia of iron body to withstand a water pressure of 200 PSIG. Valves shall
be installed at location as shown on the drawing complete with consumable, materials
etc. as per direction of Engineer-in-charge.
a) 100 mm Dia Taka Five

thousand two
8 Each 5,200.00 hundred only 41,600.00
b) 80 mm Dia Taka Three
thousand six
hundred twenty five
10 Each 3,625.00 only
36,250.00
c) 65 mm Dia Taka Two thousand
10 Each 2,400.00 four hundred only 24,000.00
d) 50 mm Dia Taka One thousand
10 Each 1,600.00 six hundred only 16,000.00
e) 40 mm Dia Taka six hundred
20 Each 660.00 sixty only 13,200.00
1 2 3 4 5 6 7
f) 32 mm Dia Taka Five hundred
5 Each 580.00 eighty only 2,900.00
g) 25 mm Dia Taka Four
20 Each 400.00 hundred only 8,000.00
h) 20 mm Dia Taka Three
2 Each 300.00 hundred only 600.00
18.2 GLOBE VALVES
Supply, fitting and fixing of Globe balues upto 40mm dia bronze body and above 40mm
dia or iron body to withstand a water pressure of 200 PSIG. Values shall be installed at
location as shown on the drawing complete with consumable, accessories etc. as per
direction of Engineer-in-charge
a) 80 mm Dia Taka Five

thousand five
b) 50 mm Dia Taka Three

thousand four
c) 40 mm Dia Taka Two
thousand eight
d) 32 mm Dia Taka Two
thousand eight
e) 25 mm Dia Taka Two
thousand six
hundred fifty only
2 Each 2,650.00 5,300.00
f) 20 mm Dia Taka Two
thousand five
hundred only
2 Each 2,500.00 5,000.00
18.3 STRAINER Taka Five

Supply, fitting and fixing of Strainers of cast iron body flanged end type assembly 10 Each 5,900.00 thousand nine 59,000.00
consumable and materials as per direction of the Engineer-in-charge hundred only
a. 65 mm dia
18.4 CHECK VALVE Taka Five

Supply, fitting and fixing of Check Valve of iron body flanged end lift check type 10 Each 5,900.00 thousand nine 59,000.00
complete companion flange, nut bolt, gasket consumable and materials as per direction hundred only
of the Engineer-in-charge
a. 65 mm dia
in figure in word
Taka Five in Taka
1 Supply, fitting and fixing of Check Valve2 of iron body flanged end lift check type 3 4 5 thousand
6 nine 7
complete companion flange, nut bolt, gasket consumable and materials as per direction hundred only
of the Engineer-in-charge
a. 65 mm dia
18.5 FOOT VALVE Taka Five

Supply, fitting and fixing of fOOT VALVE shall be flanged end/screwed end type with 12 Each 5,400.00 thousand four 64,800.00
non-return valve & treainer as per direction of the Engineer-in-charge hundred only
b. 65 mm dia
18.6 FLEXIBLE JOINT

Supply, fitting and fixing of flexible joints of mouled neoprene and shall be capable to Taka Four
absorb shock and system hammering at the line water pressure of 200 psig complete thousand seven
with flanged end. Companion flanges, adjustable screw etc. flexible joint shall be hundred only
installed at suction and discharge side of pump or as shown on the & shall be tested
20 Each 4,700.00 94,000.00
upto satistaction of the Engineer-in-charge. a. 65 mm dia
18.7 FLOAT ASSEMBLY

Supply and installation of float assembly suitable to install on 100 mm dia supply pipe. Taka Five
Float assembly shall be complete with float valve, float etc. complete as per direction of thousand nine
the Engineer-in-charge. hundred only
a)65 mm dia
5 Each 5,900.00 29,500.00
18.8 PRESSURE GUAGE

Supply and installation of Dial type Pressure Gauge of 75 mm dia suitable to read 0 to Taka Four
300 psig pressure on water pipe complete with adapter, 3 mm pet cock etc complete as 10 Each 4,000.00 thousand only 40,000.00
per direction of the Engineer-in-charge.
18.9 PRESSURE REDUCING VALVE
Supply fitting and fixing of Pressure Reducing Valves of the sizes complete in all
respect as per direction of the Engineer-in-charge. Pressure reducing valve shall be
suitable to adjust and maintain outlet pressure at 7.5 psig. Valve shall be flanged end
type and complete with all control accessories.
a) 80 mm Dia Taka Forty

thousand only
4 Each 40,000.00 160,000.00
b) 50 mm Dia Taka Seventeen
thousand two
c) 40 mm Dia Taka Twelve
thousand only
1 c) 40 mm Dia 2 3 4 5 6
Taka Twelve 7
thousand only
4 Each 12,000.00 48,000.00
d) 32 mm Dia Taka Ten
thousand nine
e) 25 mm Dia Taka Ten
thousand nine
19.0 CABLE WORKS
Supply, installation and testing of electrical cable works complete with metal Taka One million
conduit with all fittings as per drawing and direction of Engineer-in-charge. five hundred
1 L.S 1,500,000 thousand only 1,500,000.00
20.0 WATER LEVEL CONTROLLER

Supply, installation, testing and commissioning of auto water level controller for all
pump system and underground reservoir, as per direction of Engineer-in-charge.
Controller shall be capable to start the pump in sequence when water level on tank
drops down below preset level. The pump shall continue to run until the tank is filled Taka Twenty five
upto preset level. The pump will not operate when there is no water in underground 8 Set 25,000.00 thousand only 200,000.00
reservoir. Controller shall be complete with water level sensors, indication panel, control
wiring (cable) with conduit etc. complete. Product shall be from
USA/UK/JAPAN/German .
21.0 WASA CONNECTION

Obtaining permission for Water connection from Dhaka WASA from the WASA Header
to Building Premises including supply of Water Meter and installation of the Water Meter Taka Three
with all accessories and consumables as per drawings and direction of the Engineer-in-
charge and as per approval of the Dhaka WASA. All required formalities with WASA
4 L.S 300,000.00 hundred thousand 1,200,000.00
shall be done by the Contractor. only
22.0 TESTING AND COMMISSIONING

After complete installation the system shall be tested and commissioned as per Taka Five
recommendation of the manufacturer and standard. Piping system shall be tested with 1 L.S 500,000.00 hundred thousand 500,000.00
pressure in presence of the Engineer-in-charge All testing of electrical system shall be only
done as per direction. Test certification shall be taken from the Engineer.
After complete installation the system shall be tested and commissioned as per in figure in word
Taka Five in Taka
1 recommendation of the manufacturer and standard.
2 Piping system shall be tested with 3 4 5 hundred 6thousand 7
pressure in presence of the Engineer-in-charge All testing of electrical system shall be only
done as per direction. Test certification shall be taken from the Engineer.
23.0 TITAS GAS SYSTEM

A.
23.1 MS PIPE FOR TITAS GAS
Supply, fitting and fixing of MS pipe for TITAS Gas line of National Tube Product. Pipe
work shall be complete with bends, tees, elbows, socket, union, reducers, hanger,
bracket, clamp etc. complete. Approved type of sealant shall be used for threaded
connection. All pipe shall be wrapped with two layer of Black Tape. Before wrapping
with black tape the pipe surface shall be properly cleaned & read oxide paint. Pipe work
shall be suitable to withstand a pressure test of 100 psig. All MS pipe work shall be
done by "TITAS Approved Contractor".
a) 100 MM N.D (110.50MM ) Taka Two

thousand six
hundred twenty five
50 Rm 2,625.00 only
131,250.00
b) 80 mm Dia (87.50mm) Taka One thousand

six hundred fiifty
only
100 Rm 1,650.00 165,000.00
c) 50 mm N.D (60.30mm) Taka Nine hundred
thirty only
150 Rm 930.00 139,500.00
D) 25 mm N.D (33.40mm) Taka Five hundred
only
25 Rm 500.00 12,500.00
E) 20 mm N.D (26.70mm) Taka Three
hundred fifty only
100 Rm 350.00 35,000.00
23.2 BACK FILLING Taka six

Back Filling the trenches with sand (F.M 08) in 150mm layer, watering & consolidating 300 cum 600 hundred only 180,000.00
each layer upto finished level.
23.3 BUTT WELDING
Providing butt welded joints to pipes. tees, elbows etc. made above or below ground
etc. all complete in all respects as per specifications of Titas Gas (T & D)Co. Ltd. & as
per direction of the Engineer -in- charge. Before welding end of the pipe shall be
properly beveled and cleaned. Measurement shall be done on per joint of welding.
NO. Providing butt welded joints to pipes.
Description of Item
tees, elbows etc. made above or below ground Quantity Unit (To be Quoted) Quoted Amount
etc. all complete in all respects as per specifications of Titas Gas (T & D)Co. Ltd. & as in figure in word in Taka
per direction of the Engineer -in- charge. Before welding end of the pipe shall be
1 2
properly beveled and cleaned. Measurement shall be done on per joint of welding.
3 4 5 6 7
a) 100 MM N.D (110.50MM ) Taka Three

hundred twenty
20 Rm 320.00 only 6,400.00
b) 80 mm Dia (87.50mm) Taka Two
hundred fifty only
30 Each 250.00 7,500.00
c) 50 mm N.D (60.30mm) Taka Two
hundred twenty
50 Each 220.00 only 11,000.00
d) 25 mm N.D (33.40mm) Taka Two
hundred only
50 Each 200.00 10,000.00
e) 20 mm N.D (26.70mm) Taka One
hundred eighty five
50 Each 185.00 only 9,250.00
23.4 VALVES
Supplying welding fitting & fixing of the different sizes valve Tee/Service Tee to connect
the pipe lines with the Titas Gas Main pipe line etc all complete in all respects as per
specification of Titas Gas(T&D) Go Ltd. & as per direction of the Engineer-in-charge.
a) 50MM X 50MM Service Tee / Valve Tee Taka Twenty five

thousand only
4 Each 25,000.00 100,000.00
b) 50 mm N.D flange valve 150 RF Taka Twenty
thousand only
2 Each 20,000.00 40,000.00
c) 50 mm N.D Adco valve 150 RF Taka Eighteen
thousand seven
hundred fifty only
2 Each 18,750.00 37,500.00
d) 25 mm N.D Adco valve Taka Ten
thousand six
e) 20 mm N.D Adco valve Taka Nine
thousand three
hundred seventy
1 e) 20 mm N.D Adco valve 2 3 4 5 Taka6 Nine 7
thousand three
hundred seventy
10 Each 9,375.00 five only 93,750.00
f) 13 mm N.D Adco valve Taka Six
thousand two
hundred fifty only
10 Each 6,250.00 62,500.00
g) 50 mm N.D Gas strainer 150 RF Taka Twelve
thousand five
hundred only
2 Each 12,500.00 25,000.00
h) Pressure Gage 0-5 psig Taka Seven
hundred fifty only
2 Each 750.00 1,500.00
i) 20 mm Plug & Socket
Taka ninety
10 Each 90.00 only 900.00
j) MS Pipe Nipple Taka
one hundred
10 Each 125.00 twenty five only 1,250.00
24.0 INSULATION FLANGE including Taka Eighteen
thousand seven
Supplying fitting & fixing in position of cathode protection Insulation Flange etc. all 1 Each 18,750.00 hundred fifty only 18,750.00
complete of Titas Gas (T&D) Co Ltd. &direction of the Engineer- in- charge
25.0 VALVE PIT
Construction of standard size high-pressure valve pit including providing standard M.S 1 Each 3,125.00 Taka three 3,125.00
sheet valve pit cover as per drawing specifications of Titas Gas (T & D)Co. Ltd. etc. all thousand one
complete in all respects & direction of the Engineer-in- charge
hundred twenty
five only
26.0 TESTING & PURGING Taka One
Testing & Purging the pipe fines properly as per. Specifications of Titas Gas (T &D)Co. 500 Rm 100,000.00 hundred thousand 50,000,000.00
Ltd. etc. all omplete in all respects & direction of the Engineer- in- charge. only
27.0 GAS REGULATOR
Supplying fitting & fixing standard Regulator approved by Titas Gas (T & D)Co Ltd.
Including supplying of necessary fittings such as. Union socket. Elbow, Nipple etc all
complete in all respects as per specification of Titas Gas (T & D ) Co. Ltd & direction of
a) 50mm dia high pressure pilot system ( Regulator) Taka Thirty

1 2
a) 50mm dia high pressure pilot system ( Regulator) 3 4 5 6 7
1 Each 30,000.00 Thousand only 30,000.00
b) 25mm dia High pressure system (Regulator) Taka Thirteen
4 Each 13,000.00 Thousand only 52,000.00
c) 20mm dia High pressure system ( Regulator ) Taka Seven
10 Each 7,000.00 thousand only 70,000.00
28 LOCK WING COCK

Supplying fitting & fixing 20mm x 20mm (local) lock wing cock etc. all complete in all Taka Four
respects as per specification Titas Gas (T & D)Co Ltd. and as per direction of the 10 Each 4,000.00 thousand only 40,000.00
Engineer-in-charge.
29 ROAD CUTTING
Cutting & permanent re installment of the pucca (Rigid I flexible) road & mending good Taka Ten
the damages etc all complete in all respects as per specification Titas Gas(T& D)Co 50 Sqm 10,000.00 thousand only 500,000.00
Ltd. and as per direction of the Engineer-in-charge.
a) Bituminous Road
30 COMMERCIAL HOUSE LINE

30.1 G.I. PIPE
Installation of Commercial House GI pipe for supplying Titas Gas including supplying
fitting & fixing in position different dia best quality fittings & accessories cutting trenches. Take two
Walls & floors. Etc. and back filling the trenches, restoring walls and floors etc. all
complete in all respect as per specification of Titas Gas (T &D) Ltd and drawing and
80 Rm 280.00 hundred eighty 22,400.00
direction of the Engineer-in-charge only
a. 13 mm.N.D.
30.2 LINE VALVES

Supplying fitting and fixing in position different dia one way brass stop cock/gas cock Taka One
best quality & heavy type cock. complete in all Gas (T &D) Go. Ltd and direction of the 10 Each 1,500.00 thousand 15,000.00
Engineer- in- charge
a. 20 mm N.D.
five hundred
only
30.3 GAS BURNER
Supply, fitting and fixing of best quality Machine Gas Burner for Kitchen Area including
all Fittings & fixtures complete as per Drawing direction of the Engineer in charge
Supply, fitting and fixing of best quality Machine Gas Burner for Kitchen Area including in figure in word in Taka
1 all Fittings & fixtures complete as per Drawing
2 direction of the Engineer in charge 3 4 5 6 7
a) Residential Gas Burner Taka Two

thousand five
b) Machine Gas Burner (Commercial Berner) Taka seven
4 Each 7,000.00 thousand only 28,000.00
31.0 TITAS GAS CONNECTION
Complete Gas Connection from Titas gas line from nearest point available on road shall Taka Five
be under this contract. The work shall be complete with getting permission from Titas 1 L.S 500,000.00 hundred 500,000.00
Authority, road cutting with permission, piping will all welding, taping. testing, regulator
valve etc. complete in all respect. as per Drawing direction of the Engineer- in- charge
thousand only
69,558,385.00
PART- C2 : INTERNAL ELECTRIFICATION WORKS
1 2 3 4 5 6 7
1.0 CONDUIT WORK
Supply & Installation of PVC pipe and accessories of reputed manufacturers as per
routing shown in the drawing, concealed/ surface mounted in columns, ceiling, walls
and other various places as required, complete with bend/elbow, PVC circular boxes,
shaddles, rowel plugs, sockets, lock-nuts, male/female bushes, 18SWG G.I.pull/wire,
necessary thermo-cool, minimum 4-times taping of joints with plastic of thickness
O.2mm, width 19mm, S-lon solvent cement, fish wire, tying with the reinforcement steel
bar at the rate of 600mm spacing using 2X20 SWG G.I wire including tracing out the
outlets after the shuttering are removed and clearing the outlets & mending good all
damages as per drawings, specifications & direction of the Engineer-in-charge. This is
an average rate with necessary number of 16SWG sheet steel make junction/pull boxes
of appropriate sizes with 3mm approved colour (matching with all colour). all above
mentioned materiall accessories of this item. The cost shall include the necessary
cleaning and necessary civil works like cutting/ breaking of walls/columns/ceiling and
mending the plastering /painting (approved colour)
as per instruction of the Engineer-in-charge. All materials of this item will be of approved
quality
1.1.1 150 mm dia ( C - Class) 200 Rm 450.00 Taka Four hundred 90,000.00
fifty only
1.1.2 100 mm dia ( C - Class) 200 Rm 275.00 Taka Two hundred 55,000.00
Seventy five only
1.1.3 50 mm dia ( C - Class) 370 Rm 125.00 Taka One hundred 46,250.00
twenty five only
1.1.4 38 mm dia ( D - Class) 2800 Rm 88.00 Taka Eighty 246,400.00
eight only
1.1.5 25 mm dia water grade 56600 Rm 35.00 Taka Thirty 1,981,000.00
five only
1.1.6 25 mm dia Flexible pipe 8000 Rm 45.00 Taka Forty 360,000.00
Five only
1.1.7 38 mm dia Flexible pipe 280 Rm 50.00 Taka Fifty 14,000.00
Only
1.1.8 50 mm dia Flexible pipe 350 Rm 55.00 Taka fifty 19,250.00
Five only
1 2 3 4 5 6 7
2.00 CABLE WORK

Supply & installation of PVC insulated single core cable/PVC insulated & PVC sheathed
single/multi core cables of BSTI approved & having ISO9001 certified co. of the
following sizes in prelaid conduits/trench /tray and making good all damages and
termination of connection at both ends as per drawing, specification and instruction of
The rate should be quoted inclusive of locally available best/approved quality PIB
insulating tape, ceiling rose(if necessary), cable sockets, solder less connector, cutting/
cleaning the prelaid PVC pipe, connection etc. This is an average rate and all material
of this item will be of approved quality.
2.1.1 IC - 1.5 MM2 BYA 77900 Rm 29.00 Taka Twenty 2,259,100.00

nine only
2.1.2 IC - 2.5 MM2 BYA 48000 Rm 45.00 Taka Forty 2,160,000.00
five only
2.1.3 IC - 4.0 MM2 BYA 1800 Rm 65.00 Taka Sixty 117,000.00
Five only
2.1.4 IC - 6.0 MM2 BYA 600 Rm 90.00 Taka ninety 54,000.00
only
2.1.5 IC - 10 MM2 BYA 300 Rm 145.00 Taka one 43,500.00
hundred forty
five only
2.1.6 IC - 6.0 MM2 NYY 3100 Rm 160.00 Taka one 496,000.00
hundred sixty only
2.1.7 IC - 10 MM2 NYY 1100 Rm 175.00 Taka one 192,500.00
hundred seventy
five only
2.1.8 IC - 16 MM2 NYY 3300 Rm 280.00 Taka two 924,000.00
hundred eighty
only
2.1.9 IC - 25 MM2 NYY 1400 Rm 415.00 Taka four 581,000.00
hundred fifteen
only
2.1.10 IC - 35 MM2 NYY 120 Rm 560.00 Taka five 67,200.00
hundred sixty
only
1 2 3 4 5 6 7
2.1.11 IC - 50 MM2 NYY 600 Rm 780.00 Taka Seven 468,000.00
hundred eighty
only
2.1.12 IC - 70 MM2 NYY 50 Rm 1,035.00 Take One 51,750.00
thousand thirty
five only
2.1.13 IC - 95 MM2 NYY 460 Rm 1,500.00 Taka one 690,000.00
thousand five
hundred only
2.1.14 IC - 120 MM2 NYY 50 Rm 2,000.00 Taka Two 100,000.00
thousand only
2.1.15 IC -150 MM2 NYY 40 Rm 2,500.00 Taka two 100,000.00
thousand five
hundred only
2.1.16 IC -185 MM2 NYY 50 Rm 3,000.00 Taka three 150,000.00
thousand
only
2.1.17 IC -240 MM2 NYY 60 Rm 3,600.00 Taka three 216,000.00
thousand six
hundred only
3.0 EARTH CONTINUITY CONDUCTORS
Supply & installation of insulated/electrolytic annealed copper earth continuity conductor
of BSTI approved & having 1809001 certified co.of following sizes in prelaid conduit
along with cable including connection to various metallic parts as per specification,
drawing and instruction of the Engineer-in-charge:
3.1.1 IC-1.5 MM2 re BYA (Green) 38900 Rm 25.00 Taka twenty 972,500.00
five only
3.1.2 IC-2.5 MM2 re BYA (Green) 24000 Rm 40.00 Taka forty 960,000.00
only
3.1.3 IC-4.0 MM2 re BYA (Green) 500 Rm 65.00 Taka Sixty 32,500.00
five only
3.1.4 IC-6.0 MM2 BYA (Green) 960 Rm 90.00 Taka ninety 86,400.00
only
3.1.5 IC-10 MM2 BYA (Green) 300 Rm 150.00 Taka one 45,000.00
hundred
fifty only
3.1.6 IC-16 MM2 BYA (Green) 1300 Rm 250.00 Taka two 325,000.00
hundred
1 2 3 4 5 6 7
fifty only
3.1.7 IC-25 MM2 BYA (Green) 200 Rm 375.00 Taka three 75,000.00
hundred
seventy five only
3.1.8 IC-35 MM2 BYA (Green) 25 Rm 500.00 Taka Five 12,500.00
hundred only
3.1.9 IC-50 MM2 BYA (Green) 200 Rm 750.00 Taka Seven 150,000.00
hundred fifty
only
3.1.10 IC-70 MM2 BYA (Green) 50 Rm 950.00 Taka NIne 47,500.00
hundred fifty
only
4.0 LIGHT FITTINGS

4.1 Supply & installation of imported 1x36W ceiling surface mounted fluorescent light fixture Taka one
similar to Torando PX.ABS/Classic ASTB of OMS, Slovakia or F&G, Germany/Philips, 35 Set 1,400.00 thousand four 49,000.00
Netherlands complete with 1x36W fluorescent lamp, foreign 1 ballast, starter, capacitor
and all other necessary materials as per drawing, specifications and direction of the
hundred only
Engineer-in-charge.
4.2 Supply & installation of imported 2x36W ceiling surface mounted fluorescent light
fixture similar to Torando PX.ABS/Classic ASTB of OMS, Slovakia or F&G, Taka Two
Germany/Philips, Netherlands complete with 2x36W fluorescent lamps, T foreign
ballasts, starters, capacitors and all other necessary materials as per ,
thousand one
drawing, specifications and direction of the Engineer-in-charge. 720 Set 2,130.00 hundred thirty 1,533,600.00
only
4.3 Supply & installation of imported 2x36W ceiling recessed mounted fluorescent light 2
fixture similar to Relax PV Par Mat of OMS, Slovakia or F&G, Germany/Philips, Taka Two
Netherlands complete with mirror reflector, 2x36W fluorescent lamps, foreign ballasts,
starters, capacitors and all other necessary materials as per drawing, specifications and
thousand three
direction of the Engineer-in-charge. 20 Set 2,300.00 hundred only 46,000.00
4.4 Supply & installation of imported 4x18W ceiling recessed mounted fluorescent light
fixture similar Relax PV/LA of OMS, Slovakia or F&G, Germany/Philips, Netherlands Taka Two
complete with mirror reflector, 4x18W fluorescent lamps, foreign ballasts, starters,
capacitors and all other necessary materials as per drawing, specifications and direction
thousand four
of the Engineer-in-charge. 690 Set 2,450.00 hundred fifty 1,690,500.00
only
4.5 Supply & installation of imported ceiling recessed mounted double height light fixture Taka one
similar to Down light 212 BR of OMS, Slovakia or F&G, Germany/Philips, Netherlands thousand two
complete with 2x26W energy saving lamp and all other necessary materials as per
drawing, specifications and direction of the Engineer-in-charge.
230 Set 1,270.00 hundred seventy 292,100.00
only
1 2 3 4 5 6 7
4.6 Supply & installation of imported 2x9W surface mounted energy saving light fixture
similar to 31 OPAL of OMS, Slovakia or F&G, Germany/Philips, Netherlands complete Taka six
with 2x9W energy saving lamps and all other necessary materials as per drawing,
specifications and direction of the Engineer-in-charge
30 Set 635.00 hundred thirty 19,050.00
five only
4.7 Supply & installation of imported ceiling recessed mounted light fixture similar to Down
light 201 of OMS, Slovakia or F&G, Germany/Philips, Netherlands complete with 2x13W Taka Six
energy saving lamp and all other necessary materials as per drawing, specifications
1655 Set 600.00 hundred only 993,000.00
4.8 Supply & installation of imported 1 x18W wall mounted mirror light fixture of similar to
PLAST of OMS, Slovakia or F&G,Germany/Philip5, Netherlands complete with 1 X 18W Taka Nine
fluorescent lamp, ballast, capacitor, holder, etc. and all other necessary accessories as
per drawing, specifications and direction of the Engineer-in-charge.
95 Set 950.00 hundred fifty 90,250.00
only
4.9 Supply & installation of imported 2x9W surface mounted energy saving light fixture Taka Eight
similar to Forwall 11 OMS, Slovakia or F&G, Germany/Philips, Netherlands complete hundred forty
with 2x9W energy saving lamps and all other necessary materials as per : drawing,
specifications and direction of the Engineer-in-charge.
14 Set 840.00 only 11,760.00
4.10 Supply & installation of imported 2x9W surface mounted energy saving light fixture
similar to Forwall 21 OMS, Slovakia or F&G, Germany/Philips, Netherlands complete Taka Eight
with 2x9W energy saving lamps and all other necessary materials as per : drawing,
specifications and direction of the Engineer-in-charge.
20 Set 870.00 hundred seventy 17,400.00
only
4.11 Supply & installation of impor1ed wall mounted building illumination light fixture
similar to cat. no.20431 of Lanzini, Italy, or OMS, Slovakial F&G, Germany/Philips,
Netherlands complete with 1X400W metal halide lamp, base plate, nuts, screws
etc. and all other necessary accessories as per drawing, specifications and
Taka Ten
direction of the Engineer-in-charge. 10 Set 10,000.00 thousand only 100,000.00
4.12 Supply & installation of imported Aviation Light similar to PS14 with GLS-60W, Taka Three
822 lamp of Philips having blinking circuit arrangement complete with 8'-0" long Thousand six
1.5" dia G.I pipe, nuts, bolts, screws, holder and all other necessary accessories
as per specification & direction of Engineer-in-charge.
2 Set 3,600.00 hundred only 7,200.00
4.13 Supply & installation of imported LED Exit sign light similar to Exit light 2841 of OMS,
Slovakia or F&G, Germany/Philips, Netherlands complete with all respect to provide 4- Taka Five
hours backup time and all other necessary accessories as per drawing, : specifications
1 2 3 4 5 6 7
hours backup time and all other necessary accessories as per drawing, : specifications
20 Set 5,000.00 thousand only 100,000.00
5.0 SWITCH BOARD

5.1 Supply and installation of impor1ed gang switches from Legrand (France UK)
IM.K(UK)/Crabtree(UK) Nolex(UK) & wall boxes complete with all other necessary
boxes complete with all other necessary accessories & connections everything
complete as per drawing, specification and instruction of the Engineer-in-charge. The
wall boxes may be locally made of 16SWG galvanized steel sheet including
earthing block.
5.1.1 1 GANG ( 10 A) 110 Set 230.00 Tala Two 25,300.00

hundred thirty
only
5.1.2 2 GANG ( 10 A) 115 Set 320.00 Tala Three 36,800.00
hundred twenty
only
5.1.3 3 GANG ( 10 A) 164 Set 420.00 Tala Four 68,880.00
hundred twenty
only
5.1.2 4 GANG ( 10 A) 195 Set 570.00 Tala Five 111,150.00
hundred seventy
only
5.2 Supply & installation of concealed/surface type special switches in totally insulated
made switch board from Moeller/Siemens of appropriate dimension with sufficient
spacing suitable for mounting the required nos. of switches, contactors, impulse relay,
push button, earthing block, etc. from reputed manufactures like as per following ratings
with cover and all other accessories & connections as per specifications, drawing &
comprising of .
5.2.1 SSB-1 Taka one

2 to 4 nos. Push button switch 26 set 1,000.00 thousand only 26,000.00
6.0 SOCKET OUTLET
6.1 Supply and installation of imported 5A/13A, 3-pin, 250V, combined switched socket
outlet from Legrand (France UK) IM.K(UK) I Crabtree(UK) Nolex(UK) suitable for 213 Taka three
pin plug including the box, cover plate with necessary galvanized B237 machine
screws, earthing block complete with necessary connections as per drawings,
550 Set 375.00 hundred seventy 206,250.00
specifications and direction of the Engineer-in-charge. The box may be locally made of
16SWG galvanized steel sheet conforming to BS4662.
NO. Supply and installation of imported
Description
5A/13A, of Item250V, combined switched socket Quantity
3-pin, Unit (To be Quoted) Quoted Amount
outlet from Legrand (France UK) IM.K(UK) I Crabtree(UK) Nolex(UK) suitable for 213 in figure in word in Taka
pin plug including the box, cover plate with necessary galvanized B237 machine
1 2
screws, earthing block complete with necessary connections as per drawings,
3 4 5 6 7
specifications and direction of the Engineer-in-charge. The box may be locally made of five only
16SWG galvanized steel sheet conforming to BS4662.
6.2 Supply and installation of imported 15A, 3-pin, 250V, combined switched socket Quiet
from Legrand (France UK) IM.K(UK)I Crabtree(UK) Nolex(UK) suitable for 3-pin plug Taka
including the box, cover plate with necessary galvanized machine screws, earthing
block complete with necessary connections as per drawings.
20 Set 500.00 Five hundred 10,000.00
specifications and direction of the Engineer-in-charge. The box may be locally only
made of 16SWG galvanized steel sheet conforming to BS4662.
6.3 Supply and installation of imported 15A, 3-pin, 250V, combined switched socket outlet
from Legrand (France/UK) IM.K(UK)I Crabtree(UK) Nolex(UK) (outdoor type) & 3 pin
plug of approved model including the box, cover plate with necessary galvanized
machine screws, earthing block complete with necessary connections as per drawings,
Taka Six
specifications and direction of the Engineer-in-charge. The box may be locally made of 4 Set 650.00 hundred fifty 2,600.00
16SWG galvanized steel sheet conforming to 8S4662. only
6.4 Supply & installation of imported 16A/20A/25A 132A TP Motor protective circuit breaker Taka three
from Moeller(Germany)/ Siemens(Germany) with auxiliary contacts, indicating lamps, thousand two
etc. in flush/surface mounted totally insulated box as per drawing, specifications and
4 Each 3,220.00 hundred twenty 12,880.00
only
7.0 TELEPHONE SYSTEM
7.1 Supply & installation of imported surface /concealed type totally insulated telephone
junction box made of polystrol/ polycarbonate board from Moeller
(Germany)/Siemens(Germany) of following sizes with connecting strip and all required
accessories such as insulator, screw, rubber bushing, rowel plug etc. as per drawing,
specification and instruction of the Engineer-in-charge.
7.1.1 700 Pairs 1 Set 20,700.00 Taka Twenty 20,700.00

thousand seven
hundred only
7.1.2 50 Pairs 1 Set 4,025.00 Taka Four 4,025.00
thousand twenty
five only
7.1.3 30 Pairs 2 Set 2,875.00 Taka Two 5,750.00
thousand eight
1 2 3 4 5 6 7
hundred seventy
five only
7.1.4 20 Pairs 1 Set 2,075.00 Taka Two 2,075.00
thousand seventy
five only
7.1.5 15 Pairs 1 Set 1,725.00 Taka one thousand 1,725.00
seven hundred
twenty five only
7.2 Supply and installation of imported jack type shuttered telephone socket outlet from
Legrand (France/UK) IM.K(UK)I Crabtree (UK) Nolex(UK) with sheet steel box and all Taka Three
other accessories as per specifications, drawing and direction of the Engineer-in-
charge.
175 Set 335.00 hundred thirty 58,625.00
five only
7.3 Supply & installation of telephone cable of BSTI approved cable of the following sizes in
prelaid conduit and termination of connection as per drawing, specifications and
instruction of the Engineer-in-charge.
7.3.1 200 Pairs Cable (Under ground) 200 Rm 2,000.00 Taka Two 400,000.00
Thousand only
7.3.2 50 Pairs Cable 14 Rm 570.00 Take five hundred 7,980.00
seventy only
7.3.3 30 Pairs Cable 50 Rm 385.00 Take three 19,250.00
hundred eighty
five only
7.3.4 20 Pairs Cable 20 Rm 260.00 Take two 5,200.00
hundred sixty only
7.3.5 15 Pairs Cable 10 Rm 200.00 Taka two 2,000.00
hundred only
7.3.6 3 Pairs Cable 41000 Rm 38.00 Taka Thirty 1,558,000.00
eight only
8.0 FAN
8.1 Supply & installation of concealed type fan hook box (size: 4.5" dia & depth 2") made of Taka one
16SWG sheet steel box of approved quality everything complete as per : specifications, 22 Set 100.00 hundred only 2,200.00
drawing and direction of the Engineer-in-charge.
8.2 Supply & installation of 56" sweep ceiling mounted fan approved quality of reputed Taka two
company everything complete with regulator, fixing accessories, hard : wares etc. as 22 Set 2,400.00 thousand four 52,800.00
per drawing, specifications and direction of the Engineer-in-charge
hundred only
8.3 Supply & installation of 16" sweep 220V,50HZ, A.C wall mounted industrial type Take two thousand
exhaust fan approved quality of reputed company everything complete with fixing 8 Set 2,600.00 six hundred 20,800.00
accessories, hard wares etc. as per drawing, specifications and direction of the
Engineer-in-charge
only
1 2 3 4 5 6 7
9.0 DISTRIBUTION BOARD
9.1 Supply, installation, testing & commissioning of imported, type tested assembly, totally
insulated distribution boards with insulated cover conforming to IEC439-1 from
Moeller/Siemens(Germany) having ISO9001 certificate housing the following rated
MCB/ELCB /MCCB /MPCB/ ON-OFF disconnecting switches, contactors, impulse relay
& bus bars and all other accessories as per technical specification & drawings. All the
MCCB shall have adjustable overload & adjustable short circuit releases, rotary handle
& interrupting capacities as stated in the specification.
The distribution board shall be of suitable dimensions so as to accommodate the circuit

breakers and busbars with insulated shroud with sufficient spacing including internal
connection cables in the board and other materials, -shall be suitable for concealed
/surface mounted type having PVC cable glands/ grommets of appropriate sizes, shall
have knockout for conduits entry & exist, a suitable size copper plate earthing block
must be provided inside the box.
The rate should be quoted inclusive of all required inclusive of all required material for
this item & the cost shall include the necessary clearing and necessary civil works like
cutting and breaking of walls/columns/ceiling /floors and mending the same including
the plastering & painting as per instruction of the Engineer-in-charge.
9.1.1 MDB -& EMDB -Basement-2

Incoming : 1 x 100A TP MCB / DS ( C-curve)
Outgoing : 2 x 25A TP MPCB Take One hundred
: 6 x 16A SP MCB ( C-curve) 2 Set 150,000.00 fifty thousand 300,000.00
: 15 x 20A SP MCB ( C- curve) only
5 x 20A TP Contractor with auxilliary contact
5 x 16A SP Impulse Relay
2 x 120A TP+N+E Plug in type insulated Busbar
9.1.2 MDB -& EMDB -Basement-1
Incoming : 1 x 100A TP MCB / DS ( C-curve)
Outgoing : 2 x 25A TP MPCB Take One hundred
: 9 x 16A SP MCB ( C-curve) 2 Set 115,000.00 fifteen thousand 230,000.00
: 12 x 20A SP MCB ( C- curve) only
4 x 20A TP Contractor with auxilliary contact
9.1.3 EMDB -Fire Pump Take Thirty six
Incoming : 1 x 200A TP MCCB 1 Set 36,000.00 thousand 36,000.00
1 2 3 4 5 6 7
9.1.4 EMDB -Water Pump
Incoming : 1 x 200A TP MCCB
Outgoing : 2 x 100A TP MPCB/MPCB Taka one hundred
: 2 x 25 SP MCCB 1 Set 105,000.00 five thousand 105,000.00
: 300A TP +N+E Bushbar only
9.1.5 MDB -Ground Floor

Incoming : 1 x 200A TP MCCB / DS
Outgoing : 1 x 125A TP MCB (C-curve) Take one hundred
: 1 x 63A TP MCB ( C-curve) 1 Set 120,000.00 twenty thousand 120,000.00
: 1 x 40A TP MCB ( C- curve) only
: 2 x 32A TP MCB ( C- curve)
2 x120A TP+N+E Plug-in type insulated Busbar
9.1.6 SDB-1 Ground Floor
Incoming : 1 x 40A TP MCB / DS (C-curve)
+add-on 40A 4P (100mA) ELCB
Outgoing : 9 x 16A SP MCB (C-curve) Take Eoghty five
: 3 x 20A SP MCB ( C-curve) 1 Set 85,000.00 thousand only 85,000.00
1 x 20A TP Contractor with auxiliary contact
1 x 20A TP Contractor with auxiliary contact
1 x 16A SP Impilse Relay
1 x 120A TP+N+E Plug-in type insulated Busbar
Incoming : 1 x 63A TP MCB/DS (C-curve)
Outgoing : 6 x 16A SP MCB (C-curve) Take one hundred
: 9 x 20A SP MCB (C-curve) 1 Set 100,000.00 thousand only 100,000.00
3 x 20A TP Contactor with auxilliary contact
+add-on 32A 4P (100mA) ELCB Take Fifty two
Outgoing : 9 x 16A SP MCB (C-curve) 1 Set 52,000.00 thousand only 52,000.00
1 2 3 4 5 6 7
9.1.9 EMDB Ground Floor
Incoming : 1 x 63A TP MCB / DS (C-curve) Take Sixty five
Outgoing : 2 x 40A TP MCB (C-curve) 1 Set 65,000.00 thousand only 65,000.00
2 x 20A TP MCB (C-curve)
9.1.10 ESDB-1 Ground Floor

Outgoing : 6 x 16A SP MCB (C-curve) Take Eighty
: 6 x 20A SP MCB (C-curve) 1 Set 85,000.00 five thousand 85,000.00
2 x 20A TP Contactor with auxilliary contact only
Outgoing : 3 x 16A SP MCB (C-curve) Take Eighty
: 6 x 20A SP MCB (C-curve) 1 Set 85,000.00 five thousand 85,000.00
2 x 20A TP Contactor with auxilliary contact only

+add-on 25A 4P (100mA) ELCB Take Sixty
Outgoing : 6 x 16A SP MCB (C-curve) 1 Set 60,000.00 thousand only 60,000.00
9.1.13 MDB-1 1st. Floor

Incoming : 1 x 160A TP MCCB / DS (C-curve) Take One
Outgoing : 1 x 100A TP MCB (C-curve) 1 Set 120,000.00 hundred twenty 120,000.00
2 x 40A TP MCB (C-curve) thousand only
1 2 3 4 5 6 7
9.1.14 SDB-1 & 2 First Floor

+add-on 40A 4P (100mA) ELCB Take Fifty eight
Outgoing : 12 x 16A SP MCB (C-curve) 2 Set 58,000.00 Thousand only 116,000.00
9.1.15 SDB-3 1st. Floor

Incoming : 1 x 32A TP MCCB / DS (C-curve)
+add-on 32A 4P (100mA) ELCB Take Fifty
Outgoing : 9 x 16A SP MCB (C-curve) 1 Set 54,000.00 Four thousand 54,000.00
2 x 120A TP+N+E Plug-in type insulated Busbar only
9.1.16 EMDB First Floor
Incoming : 1 x 80A TP MCB / DS (C-curve) Take sixty five
Outgoing : 1 x 40A TP MCB (C-curve) 1 Set 65,000.00 thousand 65,000.00
2 x 32A TP MCB (C-curve) only
9.1.17 ESDB-1 First Floor
+add-on 40A 4P (100mA) ELCB Take Fifty eight
9.1.18 ESDB-2 & 3 First Floor
+add-on 25A 4P (100mA) ELCB Take Fifty five
9.1.19 MDB-2nd floor
Outgoing : 1 x 125A TP MCB (C-curve) Take One
2 x 63A TP MCB (C-curve) 1 Set 150,000.00 hundred fifty 150,000.00
1 x 40A TP MCB (C-curve) thousand only
1 2 3 4 5 6 7
9.1.20 SDB-1 2nd Floor
+add-on 40A 4P (100mA) ELCB Take Forty eight
9.1.21 SDB-2 & 3 2nd Floor
+add-on 63A 4P (100mA) ELCB Take Seventy six
9.1.22 SDB-4 2nd. Floor

+add-on 32A 4P (100mA) ELCB Take Ninety
2 x 20A SP MCB (C-curve)
2 x 20A TP contractor with auxiliary contact
2 x 16A SP impulse Relay
9.1.23 EMDB - 2nd. Floor
Incoming : 1 x 63A TP MCCB / DS (C-curve) Taka Fifty five
Outgoing : 2 x 32A TP MCB (C-curve) 1 Set 55,000.00 Thousand only 55,000.00
9.1.24 ESDB 1 - 2nd. Floor

+add-on 40A 4P (100mA) ELCB Taka Fifty
9.1.25 ESDB 2 & 3 2nd. Floor

+add-on 32A 4P (100mA) ELCB Taka Fifty
1 2 3 4 5 6 7
9.1.26 ESDB 4- 2nd. Floor

+add-on 25A 4P (100mA) ELCB Taka Sixty eight
9.1.27 MDB - 3rd Floor

Incoming : 1 x 200A TP MCCB / DS Taka One
Outgoing : 1 x 100A TP MCB (C-curve) 1 Set 100,000.00 hundred thousand 100,000.00
2 x 63A TP MCB (C-curve) only
9.1.28 SDB 1 & 2 3rd Floor Taka Eighty

Incoming : 1 x 63A TP MCB / DS ( C-curve) 2 Set 80,000.00 Thousand only 160,000.00
Outgoing : 18 x 16A SP MCB (C-curve)
9.1.29 SDB 3 3rd Floor Taka Ninety

1 2 3 4 5 6 7
9.1.30 SDB 4 - 3rd Floor Taka Fifty
9.1.31 EMDB -3rd Floor Taka Fifty

9.1.32 ESDB 1 & 2 - 3rd Floor Taka Fifty

9.1.33 ESDB 3 & 4 - 3rd Floor Taka forty nine

9.1.34 MDB 4th to 5th Floor Taka one hundred

Incoming : 1 x 160A TP MCCB / DS 2 Set 105,000.00 five thousand 210,000.00
Outgoing : 1 x 80A TP MCB (C-curve) only
1 2 3 4 5 6 7
9.1.35 SDB-1 & 2 - 4th to 5th Floor Taka Eighty
Incoming : 1 x 63A TP MCB / DS (C-curve) 4 Set 80,000.00 Thousand only 320,000.00
9.1.36 SDB -3 -4th to 5th Floor Taka fifty two

9.1.37 EMDB -4th to 5th Floor Taka fifty two

Outgoing : 2 x 32A TP MCB (C-curve)
9.1.38 ESDB-1&2 -4th to 5th Floor Taka forty eight

Incoming : 1 x 32A TP MCB / DS (C-curve) 4 Set 48,000.00 thousand only 192,000.00
9.1.39 ESDB-3 -4th to 5th Floor

Incoming : 1 x 25A TP MCB / DS (C-curve) 2 Set 50,000.00 Taka Fifty 100,000.00
+add-on 32A 4P (100mA) ELCB Thousand only
9.1.40 DB-1 -LIFT

Incoming : 1 x 400A TP MCCB / DS 1 Set 190,000.00 Taka One hundred 190,000.00
Outgoing : 1 x 160A TP MCCB ninety
1 2 3 4 5 6 7
4 x 100A TP MCCB Thousand only
6 x 16A/20A SP MCB
630A TP +N+E Bushbar
9.1.41 SDB-LIFT
Incoming : 1 x 160A TP MCCB / DS 1 Set 110,000.00 Taka One hundred 110,000.00
Outgoing : 2 x 100A TP MCCB Ten
3 x 16A/20A SP MCB Thousand only
250A TP +N+E Bushbar
10.0 TRAFFIC SIGNAL SYSTEM
10.1 Supply and installation of imported traffic signal light system from reputed manufacture's Taka Thirteen
complete with red, yellow and green colour lights, push button, impulse relay, contactor, 9 Set 13,000.00 Thousand only 117,000.00
timer (if necessary) and other accessories as per drawing specifications and instruction
of the Engineer-in-charge.
11.0 LIGHTING PROTECTION
11.1 Supply and installation of 450mm long 12mm dia single point copper air-terminal Taka One
including necessary bolts, nuts, clamps & all other accessories as shown in the 28 Set 1,100.00 thousand one 30,800.00
drawing.
hundred only
11.2 Supply and installation of roof and intermediate conductor made of 2SWG copper Taka Three
wire complete with necessary hole making, connecting the brass plate of air- 182 Rm 320.00 hundred twenty 58,240.00
terminals, down conductors, etc. complete as per drawing.
11.3 Supply and installation of solid copper wire 2X1/0 SWG in 40mm dia PVC pipe as down Taka Six
conductor as per drawing & specifications. 630 Rm 635.00 hundred thirty 400,050.00
five only
11.4 Supply and installation of test point of size 225X125X100mm made of 16SWG-- Take nine
sheet steel having a copper bar of 1 OOX38X 19mm as per drawing & specifications. 7 Set 950.00 hundred fifty 6,650.00
only
11.5 Supply & installation of solid copper wire earthing lead 2X2/0 SWG in 38mm dia G.I. Take one
pipe and termination of connections at both ends as per drawing & specifications. 75 Rm 1,035.00 thousand thirty 77,625.00
five only
11.6 Supply and installation of 38mm dia, 12m long G.I. pipe earth electrode sunk up to a Taka fourteen
depth of 12m below ground level to be used as earth electrode as per drawing and 10 Set 14,000.00 thousand only 140,000.00
specifications
1 2 3 4 5 6 7
specifications
11.7 Construction of 300X300X300mm earth inspection pit with R.C.C cover as per Taka One
drawing & instruction of the Engineer-in-charge. thousand six
10 Set 1,600.00 hundred only 16,000.00
12.0 CABLE TRAY/LADDER
12.1 Supply and installation of cable tray/ladder made of 18SWG galvanized sheet
steel/angle bar, flat bar of Approved quality of following sizes complete with necessary
hangers, supports, cover junction box, angers, clamps, bends, nuts, bolts, washer & all
other accessories as per drawing, specifications & direction of the Engineer-in-charge.
Take one
12.1.1 100mm width, 75mm -depth thousand five
450 Rm 1,500.00 hundred only 675,000.00
12.1.2 600mm width, 150mm -depth Take six

25 Rm 6,000.00 thousand only 150,000.00
28,007,565.00
PART- D2 : SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF DEEP TUBEWELL
1 2 3 4 5 6 7
1 Transpor1ation of Complete boring Equipment's, Labours, Carrying of all Materials to Take Fifty
site, Removing the surplus materials after Completion of work, installation of 1 L.S 50,000.00 Thousand only 50,000.00
equipment's, making necessary arrangements of electricity, water, labour shed, site
office and store, digging mud pit etc. all complete.
2 Execution of Tube well boring specification location water jet or other approved method,
the boring is 400 mm dia ver1ical hole up to designed depth and collection of soil
sample at every 10 m interval and at every charge of formation of soil including sinking
of necessary casing pipe (Measurement will be allowed from G.L to bottom of blank
pipe and the rate is inclusive of the cost of extra depth of boring for caving and siltation).
Length of boring necessary depending on the test result of test boring and
recommendation of BUET (stat size and length of strainer will however be confirmed by
BUET depending on the test result of test boring)
a) From 0 to 50m 50 Rm 1,400.00 Taka one thousand 70,000.00

four hundred only
b) From 50 to 100m 50 Rm 1,700.00 Taka one thousand 85,000.00
seven hundred only
c) From 100 to 150m 50 Rm 2,000.00 Taka Two 100,000.00
thouusand only
d) From 150 to 200m 50 Rm 2,300.00 Taka Two thousand 115,000.00
three hundred
only
3 Supply and Complete installation of the following tube well fixtures as per approved
available materials in the market and direction of Engineer-in-charge
a) 100mm dia bail plug 3m long 1 Each 7,000.00 Taka Seven 7,000.00
thousand only
b) 100mm dia blind G.P Pipe 52 Rm 800.00 Taka Eight 41,600.00
hundred only
c) 100mm dia S.S Strainer 60 Rm 8,600.00 Taka eight thousand 516,000.00
six hundred only
d) 200mm x 100 mm Reducer 1 Each 10,000.00 Taka Ten 10,000.00
1 2 3 4 5 6 7
thousand only
e) 200mm dia M.S Housing Pipe 60 Rm 6,500.00 Taka Six thousand 390,000.00
five hundred only
f) Gravel Packing around the tube well upto 15'-0 above the filter 10 Cum 1,600.00 Taka one thousand 16,000.00
six hundred only
g) Centralizer made 12 BWG MS rod at an interval of 5M 40 Each 500.00 Taka Five 20,000.00
hundred only
h) 40mm dia M.S casing upto min 2M below the raft foundation of building 8 Rm 5,000.00 Taka five 40,000.00
thousand only
4 Development of tube well by alternate surging and pumping by compressor upto Taka forty
satisfactory cleaning of water. 1 L.S 40,000.00 thousand only 40,000.00
5 Testing of the well by required Capacity of water which will be Continued upto 72 Taka forty
hrs or steady state Condition is attained 1 L.S 40,000.00 thousand only 40,000.00
6 Filling the bore hole around the tubewell top of shrouding upto the bottom of sanitary Taka one
seal by selected soil or local clay as pe standard specification 100 Rm 120.00 hundred twenty only 12,000.00
7 Making sanitary seal upto a minimum depth of 6M from GL with 12mm down graded Taka Eight
brick chips in the ration ( 1:1.5:3) 2 Cum 8,000.00 Thousand only 16,000.00
8 Water analysis to be carried out from BUET as detailed in specification of tender Taka Fifteen
document. 1 L.S 15,000.00 thousand only 15,000.00
9 Supply, Installation,Testing and commissioning of submersible pump of any reputed
brad of 80 USGMP capacity against a total head of 60M The pump shall complete with
all necessary under water cable, control/ starter penel made of 20 BWG steel sheet,
circuit breaker, starter, overload relay, time delay relay, voltmeter, ammeter, 100mm dia
Taka Four
pressure gauge. The work include supply and installation of necessary check valve, 1 L.S 400,000.00 hundred thousand 400,000.00
gate valve and column pipe of required diameter. only
10 Obtaining requisite permission from Dhaka WASA or any other Govt. agency for sinking Taka Three
of Tubewell (The Contractor shall be responsible for obtaining permission from WASA hundred thiusand
or other Govt agency )
1 L.S 300,000.00 only 300,000.00
11 38mm dia test boring including supply of all materials required to complete test boring
at site to selected place upto a depth of 300 m or upto satisfactory layer of water Taka Seventy
obtained as per specifications including testing of water and collecting sample of soil at
an internal of 10m and as per direction of Engineer-in-Charge.
1 Item 75,000.00 five thousand 75,000.00
only
2,358,600.00
CIVIL #REF!
PLUMBING 69,558,385.00
ELECTRICAL 28,007,565.00
DEEP TUBEWELL 2,358,600.00
#REF!
Seven
hundred
forty two
thousand
nine
hundred
seventeen
only
Taka One million Five hundred thousand only

dred thousand only

Boq - Pani Bhaban

Uploaded by

Copyright:

Available Formats

Boq - Pani Bhaban

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boq - Pani Bhaban

Uploaded by

Copyright:

Available Formats

BILL OF QUANTITIES

Name of Project : Cyclone Shelter at Chaddaghar, Barguna.

SL Rate in Figure and Works

2 BORING /DRILLING IN RCC PILE

3 REINFORCEMENT IN RCC PILE

Excavation up to 1.50m depth and 60m lead including cheaking

5 DEWATERING FOR BASEMENT EXCAVATION

9 RCC WORK UPTO GB

Upto Grade Beam 3,000.00 cft 260.00 780,000.00

8 DAMP PROOF MEMBRANE

14 PATENT STONE WORK

16.2 PLASTER TO BRICK WALL SURFACE

WORK UPTO 1st FLOOR ROOF

14 PATENT STONE WORK

16.2 PLASTER TO BRICK WALL SURFACE

19 DOOR FRAME WORKS

20 WOODEN DOOR SHUTTER

22 ALLUMINIUM SLIDING WINDOW

23 M.S WINDOW GRILL

WORK UPTO 2nd FLOOR ROOF

14 PATENT STONE WORK

16.2 PLASTER TO BRICK WALL SURFACE

19 DOOR FRAME WORKS

20 WOODEN DOOR SHUTTER

22 ALLUMINIUM SLIDING WINDOW

23 M.S WINDOW GRILL

ROOF TOP WORK

16.2 PLASTER TO BRICK WALL SURFACE

1.1 UPVC PIPE

a) 300 mm dia 300 Rm 2,400.00 Taka two 720,000.00

c) 200 mm dia 500 Rm 975.00 Taka Nine 487,500.00

e) 100 mm dia 1000 Rm 300.00 Taka three 300,000.00

f) 80 mm dia 50 Rm 200.00 Taka two hundred 10,000.00

1.2 UPVC T - JOINT

f) 100 mm x 100 mm x 80 mm dia 2 Each 550.00 Taka Five 1,100.00

g) 100 mm x 100 mm x 50 mm dia 50 Each 550.00 Taka Five 27,500.00

1.3 UPVC Y - JOINT

1.4 UPVC - TRAP

a) Bend 200 mm dia 10 each 2,870.00 Taka Two thousand 28,700.00

1.7 UPVC OFFSET BEND

b) 150 mm dia 15 each 1,070.00 Taka One thousand 16,050.00

c) 100 mm dia 15 each 500.00 Taka Five 7,500.00

b) 100 mm dia 10 each 130.00 Taka One 1,300.00

1.9 UPVC Clean Out Cup / service Door

a) 100 mm dia 200 Rm 2,500.00 Taka Two 500,000.00

c) 65 mm dia 100 Rm 1,620.00 Taka One thousand 162,000.00

d) 50 mm dia 200 Rm 890.00 Taka Eight hundred 178,000.00

b) 13 mm dia 50 Rm 950.00 Taka Nine hundred 47,500.00

4.2 ANGLE STOP COCK

4.3 WC Shower Rose (Push shower)

4.4 OPEN TAP / BIB COCK

4.5 BASIN PILLAR COCK

4.6 BASIN MIXTURE

4.7 SINK COCK

4.8 BOTTLE TRAP

4.9 WASHING HAND BASIN

4.10 SINK (SINGLE BOWL)

4.11 FLEXIBLE CONNECTION

4.12 Commode (Combi)