lm567c 4

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM567, LM567C
SNOSBQ4E MAY 1999 REVISED DECEMBER 2014
LM567x Tone Decoder

1 Features
3 Description
The LM567 and LM567C are general purpose tone

decoders designed to provide a saturated transistor
switch to ground when an input signal is present
within the passband. The circuit consists of an I and
Q detector driven by a voltage controlled oscillator
which determines the center frequency of the
decoder. External components are used to
independently set center frequency, bandwidth and
output delay.
20 to 1 Frequency Range With an External

Resistor
Logic Compatible Output With 100-mA Current
Sinking Capability
Bandwidth Adjustable From 0 to 14%
High Rejection of Out of Band Signals and Noise
Immunity to False Signals
Highly Stable Center Frequency
Center Frequency Adjustable from 0.01 Hz to
500 kHz
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
SOIC (8)
4.90 mm 3.91 mm
PDIP (8)
9.81 mm 6.35 mm
2 Applications
LM567C
(1) For all available packages, see the orderable addendum at

the end of the datasheet.
Touch Tone Decoding

Precision Oscillator
Frequency Monitoring and Control
Wide Band FSK Demodulation
Ultrasonic Controls
Carrier Current Remote Controls
Communications Paging Decoders
4 Simplified Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM567, LM567C
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Diagram ................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
3
4
8.1
8.2
8.3
8.4
8.5
4
4
4
5
6
Absolute Maximum Ratings ......................................

Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
9 Parameter Measurement Information .................. 8

10 Detailed Description ............................................. 8
10.1 Overview ................................................................. 8
10.2 Functional Block Diagram ....................................... 8

10.3 Feature Description................................................. 9
10.4 Device Functional Modes...................................... 10
11 Application and Implementation........................ 12

11.1 Application Information.......................................... 12
11.2 Typical Applications .............................................. 13
12 Power Supply Recommendations ..................... 19

13 Layout................................................................... 19
13.1 Layout Guidelines ................................................. 19
13.2 Layout Example .................................................... 19
14 Device and Documentation Support ................. 20

14.1
14.2
14.3
14.4
Related Links ........................................................

Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
20
20
20
20
15 Mechanical, Packaging, and Orderable

Information ........................................................... 20
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (March 2013) to Revision E
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision C (March 2013) to Revision D
Page
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 9
Submit Documentation Feedback
Copyright 19992014, Texas Instruments Incorporated
Product Folder Links: LM567 LM567C
LM567, LM567C
www.ti.com
6 Device Comparison Table

DEVICE NAME
LM567, LM567C
LMC567
DESCRIPTION
General Purpose Tone Decoder
Same as LM567C, but lower power supply current consumption and double oscillator frequency
7 Pin Configuration and Functions

8-Pin
PDIP (P) and SOIC (D) Package
Top View
Pin Functions
PIN
NAME
NO.
TYPE
DESCRIPTION
GND
Circuit ground.
IN
Device input.
LF_CAP
Loop filter capacitor pin (LPF of the PLL).
OUT
Device output.
OF_CAP
Output filter capacitor pin.
T_CAP
Timing capacitor connection pin.
T_RES
Timing resistor connection pin.
VCC
Voltage supply pin.
LM567, LM567C
www.ti.com
8 Specifications
8.1 Absolute Maximum Ratings (1) (2) (3)
MIN
MAX
UNIT
Supply Voltage Pin
Power Dissipation (4)
1100
mW
15
V3
10
V3
V4 + 0.5
70
Soldering (10 s)
260
Vapor Phase (60 s)
215
Infrared (15 s)
220
150
V8
LM567CM, LM567CN
PDIP Package
Operating Temperature Range
SOIC Package
65
Storage temperature range, Tstg

(1)
(2)
(3)
(4)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC
electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within
the Recommended Operating Conditions. Specifications are not ensured for parameters where no limit is given, however, the typical
value is a good indication of device performance.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
See http://www.ti.com for other methods of soldering surface mount devices.
The maximum junction temperature of the LM567 and LM567C is 150C. For operating at elevated temperatures, devices in the DIP
package must be derated based on a thermal resistance of 110C/W, junction to ambient. For the SOIC package, the device must be
derated based on a thermal resistance of 160C/W, junction to ambient.
8.2 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN
MAX
3.5
8.5
Input Voltage Level
8.5
8.5
Operating Temperature Range
20
120
VCC
Supply Voltage
VIN
TA
UNIT
8.3 Thermal Information

LM567C
THERMAL METRIC (1)
UNIT
8 PINS
RJA
Junction-to-ambient thermal resistance
107.5
53.0
RJC(top)
Junction-to-case (top) thermal resistance
54.6
42.3
RJB
Junction-to-board thermal resistance
47.5
30.2
JT
Junction-to-top characterization parameter
10.0
19.6
JB
Junction-to-board characterization parameter
47.0
30.1
(1)
C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
LM567, LM567C
www.ti.com
8.4 Electrical Characteristics

AC Test Circuit, TA = 25C, V+ = 5 V
PARAMETER
TEST CONDITIONS
Power Supply Voltage Range
LM567
LM567C/LM567CM
MIN
TYP
MAX
MIN
TYP
MAX
4.75
4.75
UNIT
5.0
9.0
5.0
9.0
Power Supply Current Quiescent
RL = 20k
10
mA
Power Supply Current Activated
RL = 20k
11
13
12
15
mA
25
mVrms
Input Resistance
18
Smallest Detectable Input Voltage
IL = 100 mA, fi = fo
Largest No Output Input Voltage
IC = 100 mA, fi = fo
20
10
Largest Simultaneous Outband Signal to

Inband Signal Ratio
Minimum Input Signal to Wideband Noise
Ratio
Bn = 140 kHz
Largest Detection Bandwidth
12
Largest Detection Bandwidth Skew

Largest Detection Bandwidth Variation with
Temperature
Largest Detection Bandwidth Variation with
Supply Voltage
15
25
15
4.75 6.75 V
10
0 < TA < 70
55 < TA < +125
Center Frequency Shift with Supply Voltage 4.75 V 6.75 V

4.75 V 9 V
Fastest ON-OFF Cycling Rate
15
mVrms
dB
dB
14
16
1
100
20
20
10
0.1
Highest Center Frequency

Center Frequency Stability (4.75 5.75 V)
20
18
% of fo
% of fo
0.1
2
500
1
100
35 60
35 140
0.5
14
1.0
2.0
fo/20
%/C
5
%V
500
kHz
35 60
35 140
ppm/C
ppm/C
0.4
2.0
2.0
%/V
%/V
fo/20
Output Leakage Current
V8 = 15 V
0.01
25
0.01
25
Output Saturation Voltage
ei = 25 mV, I8 = 30 mA
ei = 25 mV, I8 = 100 mA
0.2
0.6
0.4
1.0
0.2
0.6
0.4
1.0
Output Fall Time
30
30
ns
Output Rise Time
150
150
ns
LM567, LM567C
www.ti.com
8.5 Typical Characteristics
Figure 1. Typical Frequency Drift
Figure 2. Typical Bandwidth Variation
Figure 5. Bandwidth vs Input Signal Amplitude
Figure 6. Largest Detection Bandwidth
LM567, LM567C
www.ti.com
Typical Characteristics (continued)
Figure 7. Detection Bandwidth as a Function of C2 and C3
Figure 8. Typical Supply Current vs Supply Voltage
Figure 9. Greatest Number of Cycles Before Output
Figure 10. Typical Output Voltage vs Temperature
LM567, LM567C
www.ti.com
9 Parameter Measurement Information

All parameters are measured according to the conditions described in the Specifications section.
10 Detailed Description
10.1 Overview
The LM567C is a general purpose tone decoder. The circuit consists of I and Q detectors driven by a voltage
controlled oscillator which determines the center frequency of the decoder. This device is designed to provide a
transistor switch to ground output when the input signal frequency matches the center frequency pass band.
Center frequency is set by an external timing circuit composed by a capacitor and a resistor. Bandwidth and
output delay are set by external capacitors.
10.2 Functional Block Diagram
LM567, LM567C
www.ti.com
10.3 Feature Description

10.3.1 Center Frequency
The center frequency of the LM567 tone decoder is equal to the free running frequency of the voltage controlled
oscillator. In order to set this frequency, external components should be placed externally. The component
values are given by:
1.1
fo
R1 C1
where
R1 = Timing Resistor
C1 = Timing Capacitor
(1)
10.3.2 Output Filter

To eliminate undesired signals that could trigger the output stage, a post detection filter is featured in the
LM567C. This filter consists of an internal resistor (4.7K-) and an external capacitor. Although typically external
capacitor value is not critical, it is recommended to be at least twice the value of the loop filter capacitor. If the
output filter capacitor value is too large, the turn-on and turn off-time of the output will present a delay until the
voltage across this capacitor reaches the threshold level.
10.3.3 Loop Filter
The phase locked loop (PLL) included in the LM567 has a pin for connecting the low pass loop filter capacitor.
The selection of the capacitor for the filter depends on the desired bandwidth. The device bandwidth selection is
different according to the input voltage level. Refer to the Operation With Vi < 200m VRMS section and the
Operation With Vi > 200m VRMS section for more information about the loop filter capacitor selection.
10.3.4 Logic Output
The LM567 is designed to provide a transistor switch to ground output when the input signal frequency matches
the center frequency pass band. The logic output is an open collector power transistor that requires an external
load resistor that is used to regulate the output current level.
10.3.5 Die Characteristics
Figure 11. Die Layout (C - Step)
LM567, LM567C
www.ti.com
Feature Description (continued)

Table 1. Die and Wafer Characteristics
Fabrication Attributes
General Die Information
Physical Die Identification
LM567C
Bond Pad Opening Size (min)
91m x 91m
Die Step
Bond Pad Metalization
0.5% COPPER_BAL.
ALUMINUM
Passivation
VOM NITRIDE
Wafer Diameter
Physical Attributes
150mm
Back Side Metal
BARE BACK
Dise Size (Drawn)
1600m x 1626m
63.0mils x 64.0mils
Back Side Connection
Floating
Thickness
406m Nominal
Min Pitch
198m Nominal
Special Assembly Requirements:

Note: Actual die size is rounded to the nearest micron.
Die Bond Pad Coordinate Locations (C - Step)
(Referenced to die center, coordinates in m) NC = No Connection, N.U. = Not Used
SIGNAL NAME
PAD# NUMBER
X/Y COORDINATES
PAD SIZE
OUTPUT FILTER
-673
686
91
91
LOOP FILTER
-673
-419
91
91
INPUT
-673
-686
91
91
V+
-356
-686
91
91
TIMING RES
673
-122
91
91
TIMING CAP
673
76
91
91
GND
178
686
117
91
OUTPUT
-318
679
117
104
10.4 Device Functional Modes

10.4.1 Operation With Vi < 200m VRMS
When the input signal is below a threshold voltage, typically 200m-VRMS, the bandwidth of the detection band
should be calculated .
where
10
Vi = Input voltage (volts rms), Vi 200mV

C2 = Capacitance at Pin 2(F)
LM567, LM567C
www.ti.com
Device Functional Modes (continued)

10.4.2 Operation With Vi > 200m VRMS
For input voltages greater than 200m-VRMS, the bandwidth depends directly from the loop filter capacitance and
free running frequency product. Bandwidth is represented as a percentage of the free running frequency, and
according to the product of f0C2, it can have a variation from 2 to 14%. Table 2 shows the approximate values
for bandwidth in function of the product result.
Table 2. Detection Bandwidth in Function of fo C2
fo C2 (kHzF)
Bandwidth (% of fo)
62
16
7.3
4.1
2.6
10
1.8
12
1.3
14
< 1.3
14
11
LM567, LM567C
www.ti.com
11 Application and Implementation

NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TIs customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
11.1 Application Information

The LM567 tone decoder is a device capable of detecting if an input signal is inside a selectable range of
detection. The device has an open collector transistor output, so an external resistor is required to achieve
proper logic levels. When the input signal is inside the detection band, the device output will go to a LOW state.
The internal VCO free running frequency establishes the detection band central frequency. An external RC filter
is required to set this frequency. The bandwidth in which the device will detect the desired frequency depends on
the capacitance of loop filter terminal. Typically a 1F capacitor is connected to this pin. The device detection
band has a different behavior for low and high input voltage levels. Refer to the Operation With Vi < 200m VRMS
section and the Operation With Vi > 200m VRMS section for more information.
12
LM567, LM567C
www.ti.com
11.2 Typical Applications

11.2.1 Touch-Tone Decoder
Component values (typ)

R1 6.8 to 15k
R2 4.7k
R3 20k
C1 0.10 mfd
C2 1.0 mfd 6V
C3 2.2 mfd 6V
C4 250 mfd 6V
Figure 12. Touch-Tone Decoder

11.2.1.1 Design Requirements
PARAMETERS
VALUES
Supply Voltage Range
3.5 V to 8.5 V
Input Voltage Range
20 mVRMS to VCC + 0.5
Input Frequency
1 Hz to 500 kHz
Output Current
Max. 15 mA
13
LM567, LM567C
www.ti.com
11.2.1.2 Detailed Design Procedure

11.2.1.2.1 Timing Components
To calculate the timing components for an approximated desired central detection frequency (f0), the timing
capacitor value (C1) should be stated in order to calculate the timing resistor value (R1). Typically for most
applications, a 0.1-F capacitor is used.
1.1
fo
R1 C1
(2)
11.2.1.2.2 Bandwidth
Detection bandwidth is represented as a percentage of f0. It can be selected based on the input voltage levels
(Vi). For Vi < 200 mVRMS,
(3)
For Vi > 200 mVRMS, refer to Table 2 or Figure 5.

11.2.1.2.3 Output Filter
The output filter selection is made considering the capacitor value to be at least twice the Loop filter capacitor.
C3 2C2
(4)
11.2.1.3 Application Curve

IN (PIN 3)
OUT (PIN 8)
Figure 13. Frequency Detection
14
LM567, LM567C
www.ti.com
11.2.2 Oscillator with Quadrature Output
Connect Pin 3 to 2.8V to Invert Output
Figure 14. Oscillator with Quadrature Output

Refer to the previous Design Requirements section.
Refer to the previous Detailed Design Procedure section.
OUT 1 (PIN 3)
OUT 2 (PIN 8)
Figure 15. Quadrature Output
15
LM567, LM567C
www.ti.com
11.2.3 Oscillator with Double Frequency Output
Figure 16. Oscillator with Double Frequency Output

OUT 1 (PIN 5)
OUT 2 (PIN 8)
Figure 17. Double Frequency Output
16
LM567, LM567C
www.ti.com
11.2.4 Precision Oscillator Drive 100-mA Loads
Figure 18. Precision Oscillator Drive 100-mA Loads

OUT (PIN 8)
Figure 19. Output for 100-mA Load
17
LM567, LM567C
www.ti.com
11.2.5 AC Test Circuit
fi = 100 kHz + 5 V
*Note: Adjust for fo = 100 kHz.

Refer to the previous Application Curve section.
18
LM567, LM567C
www.ti.com
12 Power Supply Recommendations

The LM567C is designed to operate with a power supply up to 9 V. It is recommended to have a well regulated
power supply. As the operating frequency of the device could be very high for some applications, the decoupling
of power supply becomes critical, so is required to place a proper decoupling capacitor as close as possible to
VCC pin.
13 Layout
13.1 Layout Guidelines
The VCC pin of the LM567 should be decoupled to ground plane as the device can work with high switching
speeds. The decoupling capacitor should be placed as close as possible to the device. Traces length for the
timing and external filter components should be kept at minimum in order to avoid any possible interference from
other close traces.
13.2 Layout Example
Figure 20. LM567 Layout Example

19
LM567, LM567C
www.ti.com
14 Device and Documentation Support

14.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM567
Click here
Click here
Click here
Click here
Click here
LM567C
Click here
Click here
Click here
Click here
Click here
14.2 Trademarks
All trademarks are the property of their respective owners.
14.3 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
14.4 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
15 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
20
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package

Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (C)
Device Marking
(4/5)
LM567CM
ACTIVE
SOIC
95
TBD
Call TI
Call TI
0 to 70
LM
567CM
LM567CM/NOPB
ACTIVE
SOIC
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
567CM
LM567CMX/NOPB
ACTIVE
SOIC
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM
567CM
LM567CN/NOPB
ACTIVE
PDIP
40
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
0 to 70
LM
567CN
NE567V
OBSOLETE
PDIP
TBD
Call TI
Call TI
0 to 70
LM
567CN
(1)
The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION

www.ti.com
3-Oct-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LM567CMX/NOPB
Package Package Pins

Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.5
B0
(mm)
K0
(mm)
P1
(mm)
5.4
2.0
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION

www.ti.com
3-Oct-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM567CMX/NOPB
SOIC
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as components) are sold subject to TIs terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TIs terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TIs goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

lm567c 4

Uploaded by

Copyright:

Available Formats

lm567c 4

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

lm567c 4

Uploaded by

Copyright:

Available Formats

Product

LM567x Tone Decoder

The LM567 and LM567C are general purpose tone

20 to 1 Frequency Range With an External

BODY SIZE (NOM)

(1) For all available packages, see the orderable addendum at

Touch Tone Decoding

Absolute Maximum Ratings ......................................

9 Parameter Measurement Information .................. 8

10.2 Functional Block Diagram ....................................... 8

11 Application and Implementation........................ 12

12 Power Supply Recommendations ..................... 19

14 Device and Documentation Support ................. 20

Related Links ........................................................

15 Mechanical, Packaging, and Orderable

Changes from Revision C (March 2013) to Revision D

Changed layout of National Data Sheet to TI format ............................................................................................................. 9

Submit Documentation Feedback

Copyright 19992014, Texas Instruments Incorporated

Product Folder Links: LM567 LM567C

SNOSBQ4E MAY 1999 REVISED DECEMBER 2014

6 Device Comparison Table

7 Pin Configuration and Functions

Loop filter capacitor pin (LPF of the PLL).

Output filter capacitor pin.

Timing capacitor connection pin.

Timing resistor connection pin.

Voltage supply pin.

Submit Documentation Feedback

Copyright 19992014, Texas Instruments Incorporated

Product Folder Links: LM567 LM567C

Supply Voltage Pin

Power Dissipation (4)

Vapor Phase (60 s)

Operating Temperature Range

Storage temperature range, Tstg

8.2 Recommended Operating Conditions

Input Voltage Level

Operating Temperature Range

8.3 Thermal Information

Junction-to-ambient thermal resistance

Junction-to-case (top) thermal resistance

Junction-to-board thermal resistance

Junction-to-top characterization parameter

Junction-to-board characterization parameter

Submit Documentation Feedback

Copyright 19992014, Texas Instruments Incorporated

Product Folder Links: LM567 LM567C

SNOSBQ4E MAY 1999 REVISED DECEMBER 2014

8.4 Electrical Characteristics

Power Supply Voltage Range

Power Supply Current Quiescent

Power Supply Current Activated

Smallest Detectable Input Voltage

Largest No Output Input Voltage

Largest Simultaneous Outband Signal to

Largest Detection Bandwidth

Largest Detection Bandwidth Skew

Center Frequency Shift with Supply Voltage 4.75 V 6.75 V