Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 178 views

    Honda Accord 24

    Uploaded by

    Osmar Augusto
    This document provides instructions for connecting an ECU programmer to a 2008 Honda Accord 2.4 liter engine control unit (ECU) and reading or writing its program. It specifies connecting the red wire to pin 1 for 12V power and black wire to pin 1 for ground. For reading the ECU, it instructs removing 3 resistors and bridging 4 wires, then connecting the flat cable pins in sequence. For writing the ECU, it instructs bridging 2 wires.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Honda Accord 24

    Uploaded by

    Osmar Augusto
    178 views5 pages
    This document provides instructions for connecting an ECU programmer to a 2008 Honda Accord 2.4 liter engine control unit (ECU) and reading or writing its program. It specifies connecting the red wire to pin 1 for 12V power and black wire to pin 1 for ground. For reading the ECU, it instructs removing 3 resistors and bridging 4 wires, then connecting the flat cable pins in sequence. For writing the ECU, it instructs bridging 2 wires.

    Original Description:

    Honda accord 24

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for connecting an ECU programmer to a 2008 Honda Accord 2.4 liter engine control unit (ECU) and reading or writing its program. It specifies connecting the red wire to pin 1 for 12V power and black wire to pin 1 for ground. For reading the ECU, it instructs removing 3 resistors and bridging 4 wires, then connecting the flat cable pins in sequence. For writing the ECU, it instructs bridging 2 wires.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    178 views5 pages

    Honda Accord 24

    Uploaded by

    Osmar Augusto
    This document provides instructions for connecting an ECU programmer to a 2008 Honda Accord 2.4 liter engine control unit (ECU) and reading or writing its program. It specifies connecting the red wire to pin 1 for 12V power and black wire to pin 1 for ground. For reading the ECU, it instructs removing 3 resistors and bridging 4 wires, then connecting the flat cable pins in sequence. For writing the ECU, it instructs bridging 2 wires.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    ECU : Honda Accord 2.

    4 2008

    Connect as below:
    Serial Suite: ECU Plug:

    Red to 1 Pins Red (Power Supply +12 Volt)


    Black to 1 Pins Black (Ground)

    Piasiniengineering info@piasinienginnering.it http://www.piasiniengineering.it


    Tel: +39 0342 489060 - Fax: +39 0342 488298
    Where to connect the flat cable:

    This is where you have to connect the flat cable.

    Piasiniengineering info@piasinienginnering.it http://www.piasiniengineering.it


    Tel: +39 0342 489060 - Fax: +39 0342 488298
    READ the ECU:

    Step 1:

    You have to remove the 3 resistor, and put 4 wire (bridge), like in the picture.

    Piasiniengineering info@piasinienginnering.it http://www.piasiniengineering.it


    Tel: +39 0342 489060 - Fax: +39 0342 488298
    READ the ECU:

    Step 2:

    Connect the flat cable pin following the number like in picture.

    Piasiniengineering info@piasinienginnering.it http://www.piasiniengineering.it


    Tel: +39 0342 489060 - Fax: +39 0342 488298
    WRITE the ECU:

    For write the ECU put 2 wire(Bridge) like in the picture.

    Piasiniengineering info@piasinienginnering.it http://www.piasiniengineering.it


    Tel: +39 0342 489060 - Fax: +39 0342 488298

    You might also like