National Conference on Recent Trends in Engineering & Technology

COST COMPARISON BETWEEN FLAT SLABS WITH DROP

AND WITHOUT DROP IN FOUR STOREY LATERAL LOAD
RESISTING BUILDING
Vikunj k.Tilva Prof. B.A.Vyas
M.E Student, Applied Mechanics Department, Professor, Applied Mechanics Department,
L. D. College of Engineering, L. D. College of Engineering,
Ahmadabad, India Ahmadabad, India
tilva_vikunj@yahoo.co.in binitavyas@yahoo.com

Assit.Prof. Parth Thaker

Assit.Professor, SBST
C.E.P.T Uinversity,Ahmedabad.
Parth_thaker2003@yahoo.co.in

Abstract- The objective of this paper is to avail a cost

Flat slab structures in areas of low seismicity (Zone
comparison between flat slab panel with drop and
without drop in four storey lateral load resisting
I& II) can be designed to resist both vertical and
building. A four storey building (having 6mx6m panel) lateral loads as permitted by code IS 1893
is subjected to gravity load + lateral load in ETABS Part1:2002. However for areas of high seismicity
(Extended 3D Analysis of Building Systems) software (Zone III, IV & V) code does not permit flat slab
and then each storey is exported to SAFE(Slab Analysis construction without any lateral load resisting system.
by the Finite Element Method) software for analyzing In a building having frames(without beam) and with
punching effect due to lateral loads. On the basis of shear wall, the frames are designed for at least 25%
permissible punching shear criteria according to IS 456, of the seismic force and 75% is taken by the shear
economical thickness of flat slab with drop and without
wall.[1] If effect of lateral load analysis and other
drop are selected and cost comparison is done by using
S.O.R. (Schedule Of Rates 2008-09).
design features are to be studied in flat slabs;
punching shear is a matter of concern for any
Keywords-Punching shear stress, slab size, drop size, structural designer.
column size, and shear wall size.

I. INTRODUCTION II. DROP PANEL

Recent market conditions show that the modern

infrastructure development is aimed to utilize the
available resources to their optimum levels, may the
resources be in terms of economy or in terms of
space. When the space criterion comes into picture,
the utility of maximum space and aesthetics is the
main concern of present day architects and designers.
The slab that satisfies architectural demand for better
illumination, requires simple formwork that can be
removed faster (than other slabs ) and guarantees
open vision while making optimum use of the
available space leads to an admired concept in field
of structural engineering i.e reinforced concrete flat
slab. Thus flat slabs give an economical alternative in
utilizing the internal space to maximum extent. Flat
slab is provided in malls, theatres and other structures
where large beam free spaces are required. But today Figure 1. ETABS plan of flat slab with drop for
shear walls are compulsory for flat slab construction four-storey building
when earthquake resistance is considered.

13-14 May 2011 B.V.M. Engineering College, V.V.Nagar,Gujarat,India

 National Conference on Recent Trends in Engineering & Technology

In flat slab construction, the slab is sometimes Panel size for an Office Building -6mx6m.
thickened around the column as shown in figure 1. Dead load: self weight of slab & floor finish 1kN/m2;
The standard practice is to thicken it to at least 1.25 Live load: 4kN/m2;
times, but it should not be more than 1.5 times the Zone (III); Soil condition - medium;
thickness of the main slab. Drop can reduce the Importance Factor (I) =1;
deflection and assist in the resistance against Response Reduction Factor SMRF(R) =5;
punching shear. Such thickening is usually made Grade used: M25 and Fe- 415.
rectangular in plan with its length measured from the All columns are assumed to be square where lateral
center line of the column to not less than 1/6th the dimension D=500,550,600 and 650 mm.
smaller span of the surrounding panels. The total Locations of shear wall are sw1, sw2, sw3, sw4 as
width of the enlargement from both sides of the shown in figure 1&2.
centre line of the column is called the drop width as Earthquake force acts in both directions.
shown in figure 1.[2]
IV. PUNCHING FAILURE

III. WORK PROCEDURE Flat slab exhibits higher stress at the column
connection .They are most likely to fail due to
punching shear which will occur due to the
concentration of shear forces and the unbalanced
bending and twisting moments . It has to be noted
that the punching shear failure is rather more critical
than the flexural failure. Such a concentration of
shear force and moments leads to unsymmetrical
stress distribution around the slab-column
connections. The local and brittle nature of the
punching shear failure is in the form of crushing of
concrete in the column periphery before the steel
reinforcement reaches the yield strain. The observed
angle of failure surface is found to vary between 26
and 36. Thus the punching shear capacity of a slab
(in absence of shear reinforcement) depends on the
Figure 2. ETABS plan of flat slab without drop strength of concrete, the area of tension
for four-storey building reinforcement, the depth of the slab and the column
size.[3] The sudden disaster effect of the punching
Steps: shear is a critical problem for any designer.

1. A 3 bay-4 storey frame with drop panel and

without drop panel is modeled in ETABS with
shear wall at four corners as shown in figure 1&2.
2. Gravity and lateral loads are assigned and analysis
is performed in ETABS software. Slab is exported
to SAFE .
3. Punching shear effect is analyzed in SAFE
software.
4. On the basis of column dimension, shear wall
dimension is selected so as to resist
75%earthquake force.(ref)

Figure3 Shear and flexural cracks near vicinity of column

Model data

13-14 May 2011 B.V.M. Engineering College, V.V.Nagar,Gujarat,India

 National Conference on Recent Trends in Engineering & Technology

Permissible shear stress=0.25 = 0.25

=1.25 N/mm2
(cl. 31.6.3.2) IS 456 = 1.5x1.25
= 1.875 N/mm2
Without drop

Below graph is prepared which shows the value of

punching shear stress at edge slab-column connection
and center slab-column connection at critical storey.
Y axis indicates slab depth in mm and X axis
indicates shear stress in N/mm2.

Figure4 Shear stud rails

Stud rail

Stud rail is probably the most suitable type of

reinforcement to arrest the punching shear damage.
The system consists of studs that are welded onto a
metal strip; the studs are fabricated from plain or
deformed reinforcement bars, with an enlarged head
welded to one or both ends. Shear stud rails are to be
designed from output value of SAFE software to
resist punching shear stress.

Figure 4(a). Column 500x500mm shear wall 1400x200mm

V. TO SELECT DIMENSION OF FLAT
SLABS (WITH DROP AND WITHOUT
DROP)

For flat slab without drop ,the thickness of slab is

considered as 200mm, 225mm, 250mm, 275mm,
300mm. and critical punching shear stress value is
obtained from SAFE software analysis results.
According to IS 456, when the shear stress at the
critical section exceeds the value of c =0.25 ,
but is less than 1.5 times c shear reinforcement
shall be provided. If the shear stress exceeds 1.5c,
the flat slab shall be redesigned. [4].

13-14 May 2011 B.V.M. Engineering College, V.V.Nagar,Gujarat,India

 National Conference on Recent Trends in Engineering & Technology

Figure 4(b). Column 550x550mm shear wall 1550x200 mm depth 250mm, column 650mmx650mm and shear
wall 2000mmx200mm are selected.

Figure 4(c). Column 600x600mm shear wall 1750x200 mm

Figure 5. Column 550x550mm shear wall 1550x200 mm

With drop

From the graph of figure5, when drop is provided,

thickness of slab depth 150 mm and drop 50 mm,
column size 550mmx550mm and shear wall
1550mmx200mm are selected. This dimension is
minimum requirement for this model and shear
stirrups are required at slab-column connection.

VI. RESULT OF COST COMPARISON

Figure 4(d). Column 650x650mm shear wall 2000x200 mm

From the graph of figure 4(b), dimension of slab

depth 225 mm, column size 550mmx550mm and
shear wall 1550mmx200mm are selected. This
dimension is minimum requirement for this model
and shear stirrups are required at slab-column
connection. If designer wants to design without shear
reinforcement then from figure 7, dimension of slab

13-14 May 2011 B.V.M. Engineering College, V.V.Nagar,Gujarat,India

 National Conference on Recent Trends in Engineering & Technology

[1] IS 1893 Part1:2002 Indian Standard Criteria for

Earthquake Resistant Design of Structures,
Bureau of Indian Standards, Table 7pp 23.

[2] P.C.Varghese, Advanced Reinforced Concrete

Design, Chapter 10 pp 161.

[3] Dr N. Subramanian, Evaluation and enhancing

the punching shear resistance of flat slabs using
HSC, The Indian Concrete Journal, April 2005
pp 31-37.
[4] IS456:2000 Plain And Reinforced Concrete-
Code Of Practice, Bureau of Indian
Standards,pp53-61.

[5] Government of Gujarat schedule of rates for

building works, R&B 2008-2009.

Figure 6. Cost comparison between flat slabs with drop and

without drop

From the graph of figure 6. a cost comparison

between case 1:A flat slab of depth 225 mm without
drop and case1: flat slab of depth 150 mm with 50
mm drop(at critical third storey) is shown by bar
chart.

VII. CONCLUSION

As per the cost comparison for flat slab panel 6mx6m

for with drop and without drop , the results show that
from economic point of view slab with drop
provision is preferable. Also punching shear stress is
reduced by adopting drop at slab-column connection.
Projected cost for flat slab without drop slab is 29 %
higher than with drop slab.

Table 1. Result of cost comparison

Cost comparison of slab in accordance to Schedule

of Rates (S.O.R- R&B2008-09)[5]

Flat slab of depth 225 mm 669355

without drop

Flat slab of depth 150 mm with 518504

50 mm drop

References

13-14 May 2011 B.V.M. Engineering College, V.V.Nagar,Gujarat,India