Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

RM-250 Cat ELEC DIAG

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

KENR1700 Harness And Wire Electrical Schematic Symbols

February 1993
Symbols

Pressure Temperature Level Flow Circuit Breaker


Symbol Symbol Symbol Symbol Symbol

Symbols and Definitions


Fuse: A component in an electrical circuit that will open the circuit if too much current flows
through it.

Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The
circle indicates that the component has screw terminals and a wire can be disconnected from it.

Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.).
No circle indicates that the wire cannot be disconnected from the component.

Ground (Wired): This indicates that the component is connected to a grounded wire. The
grounded wire is fastened to the machine.

Ground (Case): This indicates that the component does not have a wire connected to ground.
It is grounded by being fastened to the machine.

Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the
contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch.

RR-250 Road Reclaimer Sender: A component that is used with a temperature or pressure gauge. The sender
measures the temperature or pressure. Its resistance changes to give an indication to
T
the gauge of the temperature or pressure.
SS-250 Soil Stabilizer Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity.

Electrical System It has a coil that makes an electromagnet when current flows through it. The
electromagnet can open or close the switch part of the relay.

Solenoid: A solenoid is an electrical component that is activated by electricity. It has a


RR-250: SS-250: coil that makes an electromagnet when current flows through it. The electromagnet
can open or close a valve or move a piece of metal that can do work.
6ED216-UP 6DD222-UP
Magnetic Latch Solenoid: A magnetic latch solenoid is an electrical component that is
activated by electricity and held latched by a permanent magnet. It has two coils (latch and unlatch)
that make electromagnet when current flows through them. It also has an internal switch that places
the latch coil circuit open at the time the coil latches.

Harness and Wire Symbols


1 Deutsch connector: Typical representation 1 Sure-Seal connector: Typical representation
of a Deutsch connector. The plug contains all of a Sure-Seal connector. The plug and receptacle
2 sockets and the receptacle contains all pins. 2 contain both pins and sockets.

Harness Identification Letter(s):


Wire, Cable, or Harness Assembly Identification: (A, B, C, ..., AA, AB, AC, ...)
Includes Harness Identification Letters and Harness
Connector Serialization Codes Harness Connector Serialization Code: The "C" stands
for "Connector" and the number indicates which
connector in the harness. (C1, C2, C3, .....)
Part Number for
C-C4 AG-C3 Connector Plug AG-C4 L-C12 Part Number For
111-7898 3E-5179 Connector Recepticle
130-6795 130-6795
325-AG135 PK-14 1 5A
Pin Socket
Receptacle Fuse
Pin or Socket (5 Amps)
Single Wire 9X-1123
Number
Connector
Component
Plug Part Number
Harness identification code: 2 200-L32 BK-14
This example indicates wire
135 in harness "AG".
Ground Circuit Identification
Connection Number Wire Color Wire Gauge

© 1993 Caterpillar Printed in U.S.A.


All Rights Reserved

(Dimensions: 34 inches x 24 inches)


KENR1700
16 Page,
7 6 5 4 3 2 1

E E

D D

C C
(Dimensions: 34 inches x 24 inches)
KENR1700

B B
16 Page,

A A

THIS SCHEMATIC IS FOR THE RR-250 ROAD RECLAIMER AND SS-250 SOIL STABILIZER
PART NUMBER: 1G-8685
Components are shown installed on a fully operable machine with the key and engine off, transmission shifter
in neutral and with parking brake set.
Refer to the appropriate Service Manual for Troubleshooting, Specifications and Systems Operations.

7 6 5 4 3 2 1

You might also like