QT013A

Hybrid Vehicle Safing Procedure for NiMh Battery
Quick Training Guide QT013A

Before servicing the high voltage system of hybrid vehicles, a safing procedure must be performed.
This Quick Reference Guide describes the safing procedures for most Toyota hybrid models.
Prepared only for technicians that are Toyota Hybrid System certified
ENTER
Click the ENTER button to view the Quick Training Guide.
©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Safing Procedure for All Hybrid Vehicle-specific Safing Procedures
Hybrid Vehicle Precautions
Vehicle Models
Click the tabs at the top to view each section

CAUTION
CAUTION
Hybrid system circuits can operate with up to 650 volts. These high
voltages are dangerous and can cause severe personal injuries, burns, The electrolyte in nickel metal hydride (NiMH) batteries in hybrid
electrical shock and even death if proper safety precautions are not vehicles is a strong alkali solution that includes potassium
followed. Always refer to the Repair Manual for vehicle-specific details. hydroxide, which is damaging to human tissues. To avoid injury
from coming in contact with the electrolyte, wear proper personal
Notice: This guide does not certify you to work on hybrid vehicle
protective equipment (PPE). Refer to the RM, FRM, ERG or other
high-voltage systems. You must complete Course 071 – Toyota Hybrid
source for chemical hazard PPE.
Systems (for service technicians), or Course 602 – Advanced Hybrid
Systems (for collision repair technicians) to safely begin working on
Toyota hybrid systems. Use the proper personal protective equipment (PPE).
Until you complete Course 071 or Course 602: The following personal protective equipment (PPE) is mandatory for working
• Never touch, disassemble, remove or replace the high-voltage parts, on the high-voltage system in Toyota hybrid vehicles:
cables and their connectors. (High-voltage parts and cables are
•
• Safety glasses (ANSI certified) with side shields
colored orange or have high-voltage warning labels.)
• Class 0 electrical insulating gloves meeting ASTM
• Do not try to access the service plug. standard specifications (up to 1000 volts)
Failure to comply with these warnings can cause severe burns or electric Gloves that have been in-service for six months
shock that may result in serious injury or death. must either:
• Be sent out for electrical testing or
Check DTCs before beginning hybrid vehicle service. • Disposed of and replaced with new gloves
Insulation malfunctions can cause high voltage to be present in Refer to the RM for care and handling of gloves and in-use check procedures.
unexpected locations. Always check DTCs and repair any isolation
faults before proceeding with vehicle service. Take responsibility for managing safety.
DTC INF Code Indicates The Certified Hybrid Technician is responsible for managing safety while
inspecting or repairing any high-voltage components.
HV Battery Voltage System Isolation
P0AA6* 526, 611, 612, 613, 614 • Confirm that the work area is dry and the areas around the hybrid
Fault
components (HV battery, inverter) are dry
Monitor CPU Malfunction
P0A1D 721, 722, 723, 787, 818 • Create and maintain a safe zone around the hybrid vehicle as appropriate.
(ECU internal error)
Malfunction in insulation monitoring • Use the “CAUTION: HIGH VOLTAGE. DO NOT TOUCH” sign to notify
P0AA7 727 other technicians that the high-voltage system is being inspected and/or
circuit in HV Battery Smart Unit
repaired. This sign can be found in most
Malfunction in HV battery voltage hybrid Repair Manuals under General >
P0A1F 129
circuit in the HV Battery Smart Unit Introduction > Repair Instruction >
Precaution. Click here for a copy.
*In 2001-2003 Prius, P3009 was used in place of P0AA6.
2 of 13
Vehicle Models
The following procedure applies to all Toyota hybrid vehicles except Prius PHV. It does NOT apply to RAV4 EV or Scion iQ EV.
Before servicing the HV system:

Even with the service plug removed, the HV battery still has high-
1. Turn the power switch OFF, and remove the key from the interior voltage components inside. Note that using non-insulated tools can
detection area for the entry and start system. cause a short circuit between high-voltage components resulting in
• When the vehicle is in READY mode, the engine may not be running – an electrical arc and burns. Always follow the safety precautions
but it can start at any time, without warning described in the Repair Manual when working around the HV battery.
• Secure the smart key at least 10 feet away from the vehicle to provide
5. Wait for 10 minutes or more to discharge the high-voltage capacitor
additional safety
inside the inverter assembly.
2. Disconnect the cable from the auxiliary battery negative terminal.
• The capacitor stores and releases high-voltage electricity supplied
3. Check the insulated gloves. by the HV battery and the motor generators
• Before use, check the insulated gloves for cracks, tears and other • The capacitor must be allowed to fully discharge before servicing
types of damage by performing the following procedure: the HV system
6. Check the voltage at the designated inspection points in the
inverter (0V check).
• Before using the voltmeter to measure voltage at the inverter
terminals, test the voltmeter by measuring the voltage of the
auxiliary battery
• Be sure the meter is set to measure the appropriate voltage range
as specified in the Repair Manual
1 Place the glove on its side
Refer to the Repair Manual for the specific test points for voltage
2 Roll the opening up 2 or 3 times, trapping as much air as possible
measurements for the vehicle you’re servicing.
within the glove
7. Insulate the disconnected high-voltage connectors with insulated
3 Fold the opening in half to close it
vinyl tape.
4 Confirm that there are no air leaks by listening for escaping air or
holding the gloves against your cheek to feel for escaping air For Additional Safety Information
4. Wearing insulated gloves, remove the service plug grip. Additional safety information for first responders and for dismantlers is
available free at http://www.techinfo.toyota.com. Go to the bottom of the
• Keep the removed service plug in your pocket (or other secure location) page and click on the “Emergency Response and Hybrid Information”
to prevent other technicians from accidentally reconnecting it while you link. There you will find:
are working on the high-voltage components
• Emergency Response Guides
Refer to the Repair Manual for the vehicle you’re servicing for the • Hybrid Emergency Responder Training
specific location of and procedure for removing the Service Plug.
• Hybrid Dismantling Manuals
3 of 13
Safing Procedure for All Hybrid
Hybrid Vehicle Precautions Vehicle-specific Safing Procedures
Vehicle Models
Avalon 2013+ Camry Highlander Highlander Prius Prius Prius Prius V Prius C
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Avalon, 2013+ and Camry, 2012+
Step 4:
Step 6:
Remove the luggage trim service hole cover,
luggage compartment floor mat, luggage
compartment front trim cover, and No. 8
hybrid vehicle battery shield panel.
Service Plug Grip
After 10 minutes,
remove the 2 bolts
and connector cover.*
x2
No. 8 Hybrid Vehicle

Battery Shield Panel
Using a measuring range of

750 V DC or more, measure the
voltage between the terminals.*
Wearing insulated gloves, Pull the lever toward you
Std. Voltage: 0V
slide the lever to the right. and remove the plug.
*Wear insulated gloves.
4 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Camry, 2007-2011
Step 4:
Service Hole Cover
Step 6:
Slide the latch upward and

open the service hole cover.
After 10 minutes,
remove the 2 bolts
and connector cover.*
Then pull to remove. Using a measuring range of

Std. Voltage: 0V
Wearing insulated
gloves, slide the lever
upward and pull down. *Wear insulated gloves.
5 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Highlander, 2006-2010
Step 4:
Step 6:
After 10 minutes, remove the
inverter cover.*
Std. Voltage: 0V
Wearing insulated gloves, pull

the lever (do not slide) and
remove the service plug grip.
Remove the 2 clips and rear
door scuff plate LH.
Remove the 2 clips and
reclining hinge cover.
6 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Highlander, 2011+
Step 4:
Remove the clips and rear Step 6:

door scuff plate LH.
After 10 minutes, remove
the 11 bolts and the
inverter terminal cover.*
Rear Door Scuff Plate LH
Rear Door LH
Remove the 2 clips and

the reclining hinge cover.

Wearing insulated gloves, pull 750 V DC or more, measure the
the lever (do not slide) and voltage between the terminals.*
remove the service plug grip. Std. Voltage: 0V
Reclining Hinge Cover *Wear insulated gloves.
7 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Prius, 2001-2003
Step 4:
Step 6: After 5 minutes:
A. Use a torx socket
Service Plug wrench (T30) to remove
the 4 screws and
B. Using a torx socket
wrench (T40), remove
the 2 screws, circuit
Terminals U, V, W breaker sensor and
connector cover.*
Slide the connector

Hint cover to disconnect
the circuit breaker
sensor connector.
Using a voltmeter,
measure the voltage
between terminals of 3
phases (U−V, V−W, U−W)
Wearing insulated gloves, and each terminal and
rotate the handle open, body ground to verify
then pull to remove. them to be approx. 0V.*
Terminals U, V, W
After removing the service plug,
cover the plug connector using *Wear insulated gloves.
Service Plug
rubber or vinyl tape.
8 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Prius, 2004-2009
Step 4:
Remove the rear floor board
Step 6:
No. 2, the rear deck floor box,
and the rear floor board No. 3.
Lever

the inverter cover.*
Using a measuring range
of 400 V DC or more,
measure the voltage
between the terminals.*
Wearing insulated gloves, slide the
Std. Voltage: 0V
lever up, then pull it down to the left.
Terminals U, V, W
Pull to the left to remove.
Using the voltmeter,

measure the voltage at
the terminals of both
three phase connectors.
Measure both connectors
between U − V, V − W,
and U − W.*
Glove Std. Voltage: 0V
Service Plug
Terminals U, V, W *Wear insulated gloves.
9 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Prius, 2010+
Step 4:
Step 6:
Remove the rear floor board
No. 2, the rear deck floor box,
and the rear floor board No. 3.

the 9 bolts and the
Service Plug Grip

slide the lever to the left. and remove the plug. Using a measuring range
measure the voltage
Std. Voltage: 0 V
10 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Prius V, 2012+
Step 4:
Step 6:
Remove the deck board
assembly, No. 1 and No. 2
deck board, rear deck floor
box, and deck floor box RH.
the 9 bolts and the
Service Plug Grip

slide the lever to the left. and remove the plug. Using a measuring range
measure the voltage
Std. Voltage: 0 V
11 of 13
Vehicle Models
Camry 2012+ 2007-2011 2006-2010 2011+ 2001-2003 2004-2009 2010+ 2012+ 2012+

Prius C, 2012+
Step 4:
Rear Seat Step 6:
Remove the front floor

cover RH, front floor
cover LH, and front
center floor cover.
Service Plug Grip

After 10 minutes,
remove the 7 bolts and
x2 the inverter cover.*
x3
Using a measuring range

x2
measure the voltage
Std. Voltage: 0 V
Wearing insulated gloves, Pull the lever toward you *Wear insulated gloves.
slide the lever downward. and remove the plug.
12 of 13
Vehicle Models

Caution Sign
Copy this sign, and after folding it, put it on the roof of the vehicle in service.
13 of 13

QT013A

Uploaded by

Copyright:

Available Formats

QT013A

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

QT013A

Uploaded by

Copyright:

Available Formats

Hybrid Vehicle Safing Procedure for NiMh Battery

Quick Training Guide QT013A

Click the ENTER button to view the Quick Training Guide.

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Click the tabs at the top to view each section

Before servicing the HV system:

Click the tabs at the top to view each section

No. 8 Hybrid Vehicle

Using a measuring range of

*Wear insulated gloves.

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Slide the latch upward and

Then pull to remove. Using a measuring range of

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Wearing insulated gloves, pull

*Wear insulated gloves.

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Remove the clips and rear Step 6:

Rear Door Scuff Plate LH

Remove the 2 clips and

Using a measuring range of

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Slide the connector

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

After 5 minutes, remove

Pull to the left to remove.

Using the voltmeter,

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

After 10 minutes, remove

Service Plug Grip

Wearing insulated gloves, Pull the lever toward you

*Wear insulated gloves.

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Service Plug Grip

Wearing insulated gloves, Pull the lever toward you

*Wear insulated gloves.

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

Click the tabs at the top to view each section

Remove the front floor

Service Plug Grip

Using a measuring range

Click the tabs at the top to view each section

©Toyota Motor Sales, U.S.A., Inc., May 31, 2013

You might also like