Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    GMK 5220 Manual

    Uploaded by

    Carlos Riffo
    This document provides instructions for accessing the normal and extended emergency modes on a GMK 7450 Telescope. 1. To access normal emergency mode, press F4 while holding the right joystick deadman switch, then press F4 again and enter the keycode BABC. 2. The extended emergency mode requires using a laptop with a valid dongle and driver to access the mode and calculate an access code using the displayed code numbers from the ECOS display. 3. Reseting the telescope status involves turning off the ignition for 5-6 seconds, then turning it back on and pressing F4 to display a red ?, holding the left deadman switch and pressing F10-F13 to view

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    GMK 5220 Manual

    Uploaded by

    Carlos Riffo
    1K views3 pages
    This document provides instructions for accessing the normal and extended emergency modes on a GMK 7450 Telescope. 1. To access normal emergency mode, press F4 while holding the right joystick deadman switch, then press F4 again and enter the keycode BABC. 2. The extended emergency mode requires using a laptop with a valid dongle and driver to access the mode and calculate an access code using the displayed code numbers from the ECOS display. 3. Reseting the telescope status involves turning off the ignition for 5-6 seconds, then turning it back on and pressing F4 to display a red ?, holding the left deadman switch and pressing F10-F13 to view

    Original Description:

    GMK 5220 technology spanish

    Original Title

    GMK 5220 manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for accessing the normal and extended emergency modes on a GMK 7450 Telescope. 1. To access normal emergency mode, press F4 while holding the right joystick deadman switch, then press F4 again and enter the keycode BABC. 2. The extended emergency mode requires using a laptop with a valid dongle and driver to access the mode and calculate an access code using the displayed code numbers from the ECOS display. 3. Reseting the telescope status involves turning off the ignition for 5-6 seconds, then turning it back on and pressing F4 to display a red ?, holding the left deadman switch and pressing F10-F13 to view

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1K views3 pages

    GMK 5220 Manual

    Uploaded by

    Carlos Riffo
    This document provides instructions for accessing the normal and extended emergency modes on a GMK 7450 Telescope. 1. To access normal emergency mode, press F4 while holding the right joystick deadman switch, then press F4 again and enter the keycode BABC. 2. The extended emergency mode requires using a laptop with a valid dongle and driver to access the mode and calculate an access code using the displayed code numbers from the ECOS display. 3. Reseting the telescope status involves turning off the ignition for 5-6 seconds, then turning it back on and pressing F4 to display a red ?, holding the left deadman switch and pressing F10-F13 to view

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Deutsche GROVE GmbH

    GMK 7450 Telescope


    Normal & Extended Emergency Access

    Access normal emergency mode:

    1. Press F4 once, hold right joystick deadman


    switch.

    2. While still holding on to the deadman switch,


    press F4 again and then enter keycode BABC,
    press enter.

    !
    ?
    ****

    For the normal emergency mode to work the following conditions must be met:

    • Locking status signals for the boom section and cylinder must be valid
    • Telescope cylinder solenoids must be without error
    • At least one too low/too high proximity switch must be active & without errors on
    other telescope cylinder proximity switches
    • ECOS or EKS5 length measurement must be functional

    Caution! should normal emergency mode not function it will be necessary to use
    extended emergency mode. When using extended emergency mode extreme caution
    should be used to verify the section/cylinder locking status and cylinder position.

    Failure to observe the caution can lead to damage to the telescope system!

    If in doubt, contact Grove LCS for advice!

    GMK 7450 Training information. Access Emergency mode. August 2002


    Deutsche GROVE GmbH
    Access Second Level Extended Emergency Mode:
    (Normal emergency must be active)

    1. You must have a valid Dongle with installed Peak driver connected to the laptop.

    NOTE: it is not necessary to connect the laptop to the crane!

    2. Use taskbar ‘options’ and click on ‘Access extended emergency mode.’

    7450

    3. Press F5 on the ECOS in-cab display, while in the telescope window then press C,
    two code numbers will be displayed e.g. 3585 0001

    F1 F5

    F2 F6

    ?
    F3 F7
    ECOS +00002 mm

    F4
    EKS5 +00000 mm
    EKS4
    F8
    3585
    ? 0001
    263s
    ?
    ! 360s
    0000 0000 0000 0000 !
    A ?
    F9 F10 F11 F12 F13 F14

    B P1 ESC

    C Enter

    4. Enter keycode 3585 in code field on laptop and press calculate. The calculated
    number e.g. 23 must then be entered on the ECOS display by turning THE
    POTENTIOMETER (P1) to match exactly and then press enter. The icon will then
    change to tools to indicate access.

    Note:

    If time clock expires, go back to normal


    emergency mode (as step 1) and press C &
    enter to restart time clock without having to
    calculate a new access code.

    GMK 7450 Training information. Access Emergency mode. August 2002


    Deutsche GROVE GmbH

    Reset telescope status

    Note: You will have to reset the telescope


    status after you re-start ECOS

    1. Turn off ignition key for approx. 5/6


    seconds

    2. Turn on the ignition. Press F4. A red ? should


    appear in the white tele box.

    3. Hold down the deadman switch on the left


    joystick. While holding the left deadman switch,
    press F10 - F13 to view % of the tele sections in
    yellow. Match the % of sections to the actual boom
    configuration or choose intermediate position if
    applicable.

    NOTE:
    Ensure that the % / intermediate positions of telescope sections viewed in the
    ECOS screen matches the exact configuration of the boom.

    4. Press Enter and look for a cursor to appear in the section box. Press
    buttons ABAC to accept the configuration.
    ?
    !
    ****
    5. Verify that the red ? has disappeared from the white tele box. The telescope
    status has been successfully reset.

    Should the red ? remain and the EKS 5 boom length display flashes you must re-
    check and re-enter the boom configuration status.

    GMK 7450 Training information. Access Emergency mode. August 2002

    You might also like