Televisores A Color
Televisores A Color
Ajustes generales
Instrucciones de seguridad
SERVICE MANUAL
COLOR TELEVISION
N0E Chassis
19A20 (TAC0001)
TOSHIBA CORPORATION
1-1, SHIBAURA 1- CHOME, MINATO-KU, TOKYO 105-8001, JAPAN
SPECIFICATIONS .................................................................................................................................................. 29
APPENDIX:
CIRCUIT DIAGRAM
–2–
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
GENERAL ADJUSTMENTS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW.
SPECIFIC INFORMATIONS
type tube as specified in the parts list.
Each time a receiver requires servicing, the high voltage 4. Some part in this receiver have special safety-related char-
should be checked following the HIGH VOLTAGE CHECK acteristics for X-RAY RADIATION protection. For contin-
procedure in this manual. It is recommended that the read- ued safety, parts replacement should be undertaken only
ing of the high voltage be recorded as a part of the service after referring to the PRODUCT SAFETY NOTICE below.
record. It is important to use an accurate and reliable high
voltage meter.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfa- Connect a 1500 ohm 10 watt resistor, paralleled by a 0.15
miliar with the necessary precautions on this receiver. The fol- µF, AC type capacitor, between a known good earth ground
lowing are the necessary precautions to be observed before (water pipe, conduit, etc.) and the exposed metallic parts,
servicing this chassis. one at a time. Measure the AC voltage across the combi-
1. An isolation Transformer should be connected in the power nation of 1500 ohm resistor and 0.15 µF capacitor. Re-
line between the receiver and the AC line before any serv- verse the AC plug at the AC outlet and repeat AC voltage
ice is performed on the receiver. measurements for each exposed metallic part. Voltage
2. Always discharge the picture tube anode to the CRT con- measured must not exceed 0.3 volts rms. This corresponds
ductive coating before handling the picture tube. The pic- to 0.2 milliamp. AC. Any value exceeding this limit consti-
ture tube is highly evacuated and if broken, glass frag- tutes a potential shock hazard and must be corrected im-
ments will be violently expelled. Use shatter proof gog- mediately.
gles and keep picture tube away from the unprotected body AC VOLTMETER
while handling.
3. When replacing a chassis in the cabinet, always be cer-
tain that all the protective devices are put back in place,
such as; non-metallic control knobs, insulating covers,
shields, isolation resistor-capacitor network etc.
4. Before returning the set to the customer, always perform
an AC leakage current check on the exposed metallic parts 0.15µF
of the cabinet, such as antennas, terminals, screwheads,
metal overlays, control shafts etc. to be sure the set is Place this probe on
safe to operate without danger of electrical shock. Plug Good earth ground each exposed
the AC line cord directly into a 120V AC outlet (do not use such as a water metallic part.
a line isolation transformer during this check). Use an AC pipe, conduit, etc. 1500 ohm
voltmeter having 5000 ohms per volt or more sensitivity in 10 watt
the following manner:
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by
the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray
radiation or other hazards.
–3–
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
GENERAL ADJUSTMENTS
SET-UP ADJUSTMENT
SET-UP ADJUSTMENT FOR 13", 14", 19", 20".
■ The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
Mounting position of the purity magnet assembly should fit to same position as old one because slightly difference to
the position depend on a kind of tube.
* There are no adjustment of purity and convergence in some picture tube (Unified with purity magnet)
SPECIFIC INFORMATIONS
TEMPORARY
DEFLECTION MOUNTING
YOKE
14mm(13", 14")
19mm(19", 20")
RUBBER WEDGE
ADHESIVE
PURITY/
CONVERGENCE DEFLECTION
MAGNET ASS'Y YOKE
GLASS CLOTH
TAPES
Figure 1.
–4–
CONVERGENCE ADJUSTMENTS ■ CIRCUMFERENCE CONVERGENCE ADJUSTMENT
NOTE: Before attempting any convergence adjustments, the 1. Loosen the clamping screw of deflection yoke slightly to
receiver should be operated for at least fifteen min- allow the yoke to tilt.
utes. 2. Temporarily put a wedge as shown in figure 1. (Do not
GENERAL ADJUSTMENTS
remove cover paper on adhesive part of the wedge.)
■ CENTER CONVERGENCE ADJUSTMENT 3. Tilt front of the deflection yoke up or down to obtain better
1. Use the cross-dot pattern from among the built-in test sig- convergence in circumference. (See figure 3.) Push the
nals. mounted wedge into the space between picture tube and
2. Set the brightness and contrast for well defined pattern. the yoke to fix the yoke temporarily.
3. Adjust two tabs of the 4-Pole Magnets to change the an- 4. Put other wedge into bottom space and remove the cover
gle between them (See figure 2.) and superimpose red paper to stick.
and blue vertical lines in the center area of the picture 5. Tilt front of the yoke right or left to obtain better conver-
screen. gence in circumference. (See figure 3.)
4. Turn the both tabs at the same time keeping the angle 6. Keep the yoke position and put another wedge in either
constant to superimpose red and blue horizontal lines at upper space. Remove cover paper and stick the wedge
the center of the screen. on picture tube to fix the yoke.
5. Adjust two tabs of 6-Pole Magnets to superimpose red/ 7. Detach the temporarily mounted wedge and put it in an-
blue line and green one. Adjusting the angle affects the other upper space. Stick it on picture tube to fix the yoke.
vertical lines and rotating both magnets affects the hori- 8. After fixing three wedges, recheck overall convergence.
Tighten the screw firmly to fix the yoke and check the yoke
SPECIFIC INFORMATIONS
zontal lines.
6. Repeat adjustments 3, 4, 5 keeping in mind red, green is firm.
and blue movement, because 4-Pole Magnets and 6-Pole 9. Stick three adhesive tapes on wedges as shown in figure
Magnets have mutual interaction and make dot movement 1.
complex.
6-POLE
MAGNETS
4-POLE ADJUST THE ANGLE
(VERTICAL LINES) FIXED
MAGNETS
PURITY
MAGNETS
Figure 2.
BLU RED RED/BLU GRN
BLU RED/BLU
RED GRN
BGR
B
G
R RGB
R B
G G
B R
BGR
R
G
RGB B
INCLINE THE YOKE UP (OR DOWN) INCLINE THE YOKE RIGHT (OR LEFT)
* There are no adjustment of purity and convergence in some picture tube (Unified with purity magnet)
SPECIFIC INFORMATIONS
Adhesive
Green Belt
Figure 2.
–6–
CONVERGENCE ADJUSTMENTS
NOTE: Before attempting any convergence adjustments, 4-POLE
the receiver should be operated for at least fifteen MAGNETS
minutes.
GENERAL ADJUSTMENTS
6-POLE
MAGNETS
■ CENTER CONVERGENCE ADJUSTMENT
1. Display built-in cross-dot pattern using the TEST SIG-
NAL SELECTION function.
2. Adjust the BRIGHTNESS and CONTRAST Controls
for well defined pattern.
3. Loosen the tightening ring and adjust two tabs of the
4-Pole Magnets to change the angle between them
PURITY
(See figure 4.) and superimpose red and blue vertical
MAGNETS
lines in the center area of the picture screen.
(See figure 3.)
PURITY/CONVERGENCE
4. Turn the both tabs at the same time keeping the con-
MAGNETS
stant angle to superimpose red and blue horizontal
lines at the centre of the screen. (See figure 3.)
SPECIFIC INFORMATIONS
5. Adjust two tabs of 6-Pole Magnets to superimpose red/ ADJUST THE ANGLE
FIXED
blue line with green one. Adjusting the angle affects (VERTICAL LINES)
the vertical lines and rotating both magnets affects the
horizontal lines.
6. Repeat adjustments 3, 4, 5 keeping in mind red, green
and blue movement, because 4-Pole Magnets and 6-
Pole magnets interact and make dot movement com-
plex.
7. After completing the “CENTER CONVERGENCE AD-
JUSTMENT” tighten the tightening ring to fix the mag- ROTATE TWO TABS
nets. AT THE SAME TIME
(HORIZONTAL LINES)
BLU RED RED/BLUE GRN ADJUSTMENT OF MAGNETS
Figure 4.
BLU RED/BLUE
RED GRN ■ SCREEN-CORNER CONVERGENCE
When the misconvergence is still evident on corners even
though the above adjustment is done, use the ferrite sheet
4-POLE MAGNETS 6-POLE MAGNETS (Part No. 23993622) to correct misconvergence.
MOVEMENT MOVEMENT 1. Put ferrite sheets into the space under the yoke.
Decide such position that misconvergence becomes
Center Convergence by Convergence Magnets minimum, watching picture screen. (See figure below.)
2. Remove cover paper of ferrite sheet to stick it in the
Figure 3. place on the tube. Put adhesive tapes on ferrite sheets
to fix.
■ Xv COIL ADJUSTMENT
Adjust the Xv coil (on the deflection yoke) to correct
misconvergence at both sides on screen.
Use a hexagonal tip stick (plastic) to adjust the core of
coil.
Clockwise Adjustment Counterclockwise Adjustment
Ferrite Ferrite
Sheets Sheets
R B B R
B R R B
A
–7–
SERVICE MODE
1. ENTERING TO SERVICE MODE
GENERAL ADJUSTMENTS
1) Press MUTE button once 2) Press MUTE button 3) While pressing the MUTE button,
on Remote Control. again to keep pressing. press MENU button on TV set.
MUTE
(Service mode display)
Item
Press Data
S
Press
–8–
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2.
(t button for reverse order)
GENERAL ADJUSTMENTS
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 15)
SPECIFIC INFORMATIONS
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Programming Channel Memory”.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
• Black cross-hatch
• White cross-hatch
2) Press “8” button while any built-in test pattern to on the screen to
output the 1 kHz sound. Press the button again to cut off the sound.
Note: If the video cable is connected to the VIDEO1 INPUT jack, the
• Black cross-dot
built-in pattern signals are not displayed.
• White cross-dot
• H signal (white)
• H signal (black)
* The signals marked with are not usable to display in the Test signal for some model.
–9–
8. SELF DIAGNOSTIC FUNCTION (MTS Model)
1) Press “9” button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
GENERAL ADJUSTMENTS
SELF CHECK
1 NO. 23XXXXXX
2 POWER : 000
3 BUS LINE : OK
4 BUS CONT : OK
5 BLOCK : UV V1 V2
or QV01 QV01S
SYNC
SPECIFIC INFORMATIONS
* The items marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.
– 10 –
DESIGN MODE
1. ENTERING TO DESIGN MODE
GENERAL ADJUSTMENTS
1) Select the Service mode. 2) While pressing RECALL button on. 3) Press MENU button on TV.
Remote and press MENU button on TV.
S D Press ITEM
DATA
Press
SPECIFIC INFORMATIONS
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL t button in the design mode changes the adjustment items in the order of table-3.
(s button for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 15)
– 11 –
ELECTRICAL ADJUSTMENTS
GENERAL ADJUSTMENTS
FOCUS VR ADJ. 1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern
appears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the
picture screen.
HORIZONTAL POSITION 1. Call up the adjustment mode display, then select the Item HPOS or VPOS.
(HPOS) 2. Press the TV/VIDEO button until the white cross-bar
VERTICAL POSITION or black cross-bar pattern appears on the screen.
(VPOS) 3. Adjust the HORIZONTAL and VERTICAL position
alternately by pressing the VOLUME s or t button
for proper picture position.
4. Check the picture with off-air signal.
HEIGHT 1. Call up the adjustment mode display, then select the Item HIT.
(HIT) 2. Press the VOLUME s or t button to get the picture so the top of raster begins
to lack.
3. Press the VOLUME s button to advance the data by 8 steps.
Note : Check the vertical picture position is correct.
– 12 –
ITEM ADJUSTMENT PROCEDURE
WHITE BALANCE 1. Adjust the CONTRAST control to the center, and BRIGHTNESS control to the
GENERAL ADJUSTMENTS
RCUT maximum.
GCUT 2. Call up the adjustment mode display, and press the TV/VIDEO button until the
BCUT white and black pattern appears on the screen.
GDRV 3. Adjust the following address with the CHANNEL s/t and VOLUME s/t
BDRV buttons.
Item : RCUT Data : 30H Item : GDRV Data : 80H
Item : GCUT Data : 30H Item : BDRV Data : 80H
Item : BCUT Data : 30H
4. Press “100” button on the Remote Control to display a single horizontal line on
the screen.
5. Turn the SCREEN control (FBT) fully counterclockwise and gradually rotate
clockwise until the first horizontal line appears slightly on the screen.
6. Press “100” button to display the normal picture.
7. Adjust the remaining two “?CUT” Item (CHANNEL s/t → 100 → VOLUME s/t
SPECIFIC INFORMATIONS
in order) to obtain the slightly lighted horizontal line in the same levels of three
(red, green, blue) colors. The line should be white if the adjustments are proper.
Bright area
Adjust "GDRV" or "BDRV" to be white.
Dark area
Fine adjust "RCUT", "GCUT" or "BCUT" to be black.
– 13 –
CIRCUIT CHECKS
HIGH VOLTAGE CHECK Troubleshooting Guide for Fail Safe Circuit
GENERAL ADJUSTMENTS
FS CIRCUIT CHECK
The Fail Safe (FS) circuit check is indispensable for the final DATA on page15)
check in servicing. Checking should be done following the
steps below.
1. Turn the receiver on and press the RESET button. NO
2. Temporarily short TP-(R) and TP-(X) with a jumper wire.
Defective Fail Safe Circuit
Raster and sound will disappear.
3. The receiver must remain in this state even after removing
the jumper wire. This is the evidence that the FS circuit is
functioning properly.
4. To obtain a picture again, temporarily turn the receiver off
and allow the FS circuit more than 5 seconds to reset.
Then turn the power switch on to produce a normal pic-
ture.
– 14 –
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
19"
HIGH VOLTAGE AT ZERO BEAM: (A) 24.7 kV
MAX HIGH VOLTAGE: (B) 26.1 kV
Table-1
SERVICE MODE
SPECIFIC INFORMATIONS
Item Name of adjustment Reference Data
DESIGN MODE
Data
Item Name of adjustment Remarks
Preset Data
Table-3
CIRCUIT CHECKS
19"
FBT DETECTION VOLTAGE (C)
22.03 V
Table-4
– 15 –
LOCATION OF CONTROLS
GENERAL ADJUSTMENTS
Front
SPECIFIC INFORMATIONS
POWER
MENU VOLUME CHANNEL
Remote sensor
Remote Control
POWER
TV/VIDEO
TV/VIDEO button POWER button
1 2 3
4 5 6
Channel Number button
7 8 9
100 0 CH RTN
RTN button
RECALL button
RECALL CH MUTE
MUTE button
VOLUME T / S button
(Menu T / S button) VOL VOL
CHANNEL s/t buttons
(Menu s/t buttons)
MENU button EXIT button
MENU CH EXIT
– 16 –
PROGRAMMING CHANNEL MEMORY
The channel memory is the list of TV channel numbers your TV will stop on when you press the CHANNEL s or t button.
GENERAL ADJUSTMENTS
First, use the TV/CABLE and CH PROGRAM functions to preset all active channels in your area.
If necessary, arrange the preset channels with the ADD/ERASE functions so that you can tune into only desired channels.
SPECIFIC INFORMATIONS
CH PROGRAM function
3 Press ;(<) or :(>) :
1 Press MENU (then s or t) repeatedly until "CH PRO- To erase the channel
GRAM" in the Set up menu is displayed in purple. Press the button until “Erase” is displayed in purple indicat-
ing that the channel has been erased from the memory.
2 Press ;(<) or :(>) to start channel programming.
The TV will automatically cycle through all the TV or CABLE To add the channel
channels depending on the mode selected, and store Press the button until “ADD” is displayed in purple indicat-
active channels in the channel memory. ing that the channel has been memorized.
3 When channel programming is complete, you will see the 4 Repeat steps 1 to 3 for other channels.
message to the right.
You have now completed the channel programming.
4 Press CHANNEL s or t to make sure the channel pro-
gramming has been done properly.
– 17 –
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS
H001
TUNER/IF/VIDEO
AUDIO OUT
W661
SPEAKER Q610
Q501
VIDEO/CHROMA/DEF
QA01 V-TV
MICROPROCESSOR C R T D R I V E B OA R D
AUDIO OUT
R
KEY SCL SCL R OUT Q901
CONTROL G V901
SDA SDA G OUT Q902
B PICTURE TUBE
B OUT Q903
DB03
RMT IN
R/SENSOR
L462
QA02 +200V DEF YOKE
MEMORY
V OUT
RESET
H OUT V. OUT
POWER QB30
– 18 –
5V Q301
FOCUS
SCREEN
H.V.
H DRIVE H. OUT
QB33
Q402 Q404
QB17 +26V
D840
Q843 QB18
QB19 T461
FBT
+9V Q421
SR81 F470
+134V CRT HEATER
Q801
FAIL SAFE
Q471
F801 T801 +32V
VOLT Q472
F802 REGU
D801~D804
P801
DEGAUSSING
COIL
L901
CHASSIS AND CABINET REPLACEMENT PARTS LIST
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY
PRECAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate com-
GENERAL ADJUSTMENTS
ponents which have special characteristics important for safety and should be replaced only with types identical to
those in the original circuit or specified in the parts list. The mounting position of replacements is to be identical
with originals. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not
degrade the safety of the receiver through improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model
number and Description.
• The PC board assembly with
* mark is no longer available after the end of the production.
Models : 19A20
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
SPECIFIC INFORMATIONS
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
Location Location
Part No. Description Part No. Description
No. No.
– 19 –
Location Location
Part No. Description Part No. Description
No. No.
CS03 24797478 EL, 0.47?F, ±20%, 50V R602 24532100 FR, 10 ohm, 1W
GENERAL ADJUSTMENTS
CS11 24797478 EL, 0.47?F, ±20%, 50V R603 24366391 CF, 390 ohm
CT63 24591223 PF, 0.022?F R604 24366182 CF, 1800 ohm
CV06 24797478 EL, 0.47?F, ±20%, 50V R605 24366339 CF, 3.3 ohm
R802 24376224 CF, 220k ohm, 1/2W
RESISTORS R803 24553123 OMF, 12k ohm, 1W
R101 24382153 OMF, 15k ohm, 1W R804 24002000 CC, 3.9M ohm, ±10%, 1/2W
R201 24552391 OMF, 390 ohm, 1/2W R806 24552560 OMF, 56 ohm, 1/2W
R208 24366124 CF, 120k ohm R808 24000269 PTC Thermistor, 7 ohm,
R218 24366154 CF, 150k ohm ±20%, AC140V
R227 24366153 CF, 15k ohm R810 24568229 Cement, 2.2 ohm, 7W
R230 24366223 CF, 22k ohm R811 24007851 Cement, 200 ohm, 15W
R233 24366152 CF, 1500 ohm R812 24510120 Cement, 12 ohm, 5W
R235 24366154 CF, 150k ohm R816 24366471 CF, 470 ohm
R236 24366101 CF, 100 ohm R818 24366561 CF, 560 ohm
R237 24366101 CF, 100 ohm R819 24366102 CF, 1k ohm
R238 24366332 CF, 3300 ohm R830 24381330 OMF, 33 ohm, 1/2W
SPECIFIC INFORMATIONS
R239 24366152 CF, 1500 ohm R831 24366681 CF, 680 ohm
R241 24366433 CF, 43k ohm R841 24568752 Cement, 7500 ohm, 7W
R242 24366473 CF, 47k ohm R845 24384123 OMF, 12k ohm, 3W
R245 24366184 CF, 180k ohm R847 24366392 CF, 3900 ohm
R246 24366225 CF, 2.2M ohm R848 24366103 CF, 10k ohm
R247 24366471 CF, 470 ohm R897 24019472 Varistor, ENE271D-10A2
R301 24366102 CF, 1k ohm R899 24019472 Varistor, ENE271D-10A2
R303 24366102 CF, 1k ohm R901 24376472 CF, 4700 ohm, 1/2W
R304 24366683 CF, 68k ohm R902 24376472 CF, 4700 ohm, 1/2W
R305 24322109 MF, 1 ohm, 1W R903 24376472 CF, 4700 ohm, 1/2W
R306 24366753 CF, 75k ohm R911 24366101 CF, 100 ohm
R307 24366914 CF, 910k ohm R912 24366101 CF, 100 ohm
R312 24381152 OMF, 1500 ohm, 1/2W R913 24366101 CF, 100 ohm
R313 24366184 CF, 180k ohm R920 24000880 FR, 5.1 ohm, 1W
R317 24366333 CF, 33k ohm R921 24366331 CF, 330 ohm
R327 24338829 MF, 8.2 ohm, 1W R922 24366331 CF, 330 ohm
R336 24383271 OMF, 270 ohm, 2W R923 24366331 CF, 330 ohm
R337 24366223 CF, 22k ohm R931 24366102 CF, 1k ohm
R338 24366223 CF, 22k ohm R932 24366102 CF, 1k ohm
R401 24366391 CF, 390 ohm R933 24366102 CF, 1k ohm
R402 24366103 CF, 10k ohm R961 24554183 OMF, 18k ohm, 2W
R403 24366332 CF, 3300 ohm R962 24554183 OMF, 18k ohm, 2W
R405 24553392 OMF, 3900 ohm, 1W R963 24554183 OMF, 18k ohm, 2W
R406 24366333 CF, 33k ohm R971 24366821 CF, 820 ohm
R407 24366223 CF, 22k ohm R972 24366102 CF, 1k ohm
R410 24366391 CF, 390 ohm R973 24366391 CF, 390 ohm
R411 24366561 CF, 560 ohm R974 24366221 CF, 220 ohm
R412 24366560 CF, 56 ohm RA03 24366102 CF, 1k ohm
R414 24383222 OMF, 2200 ohm, 2W RA07 24366102 CF, 1k ohm
R416 24510182 Cement, 1800 ohm, 5W RA14 24366102 CF, 1k ohm
R430 24366102 CF, 1k ohm RA16 24366102 CF, 1k ohm
R431 24366103 CF, 10k ohm RA17 24366102 CF, 1k ohm
R432 24366222 CF, 2200 ohm RA18 24366102 CF, 1k ohm
R448 24338828 MF, 0.82 ohm, 1W RA22 24366472 CF, 4700 ohm
R472 24376270 CF, 27 ohm, 1/2W RA23 24366472 CF, 4700 ohm
* R475 24367101 CF, 100 ohm, ±2% RA24 24366472 CF, 4700 ohm
R476 24366823 CF, 82k ohm RA25 24366682 CF, 6800 ohm
R477 24366223 CF, 22k ohm RA26 24366102 CF, 1k ohm
* R478 24327133 MF, 13k ohm, ±1%, 1/4W RA27 24366102 CF, 1k ohm
R481 24366333 CF, 33k ohm RA33 24366103 CF, 10k ohm
* R482 24327512 MF, 5100 ohm, ±1%, 1/4W RA35 24366102 CF, 1k ohm
R495 24383222 OMF, 2200 ohm, 2W RA36 24366103 CF, 10k ohm
R496 24383182 OMF, 1800 ohm, 2W RA37 24366331 CF, 330 ohm
R503 24366334 CF, 330k ohm RA38 24366331 CF, 330 ohm
R504 24366332 CF, 3300 ohm RA61 24366103 CF, 10k ohm
R513 24366332 CF, 3300 ohm RA62 24366103 CF, 10k ohm
R514 24366332 CF, 3300 ohm RA67 24366103 CF, 10k ohm
– 20 –
Location Location
Part No. Description Part No. Description
No. No.
GENERAL ADJUSTMENTS
RA70 24366333 CF, 33k ohm QB21 23114528 Transistor, 2SC1740S, Q
RA71 24366683 CF, 68k ohm QB30 23114528 Transistor, 2SC1740S, Q
RA72 24366223 CF, 22k ohm QB33 70119743 IC, PST523D
RA73 24366103 CF, 10k ohm QB40 23114528 Transistor, 2SC1740S, Q
RA74 24366101 CF, 100 ohm D101 23316411 Diode, Zener, HZT33-12
RA75 24366101 CF, 100 ohm D201 23316656 Diode, Zener, MTZJ3.3A
RB03 24366101 CF, 100 ohm D204 23118859 Diode, 1SS133
RB09 24366470 CF, 47 ohm D205 23118859 Diode, 1SS133
RB26 24366472 CF, 4700 ohm D210 23118859 Diode, 1SS133
RB27 24366103 CF, 10k ohm D301 A7568460 Diode, TVR-1B
RB28 24366104 CF, 100k ohm D302 23118095 Diode, ERB44-06, E
RB30 24366103 CF, 10k ohm D406 23118095 Diode, ERB44-06, E
RB33 24366102 CF, 1k ohm D408 23118052 Diode, RU4Z LF-L1
RB43 24366103 CF, 10k ohm D410 23316688 Diode, Zener, MTZJ9.1C
RB44 24366682 CF, 6800 ohm D441 23316687 Diode, Zener, MTZJ9.1B
RB45 24366221 CF, 220 ohm D445 23118479 Diode, BYD33J
SPECIFIC INFORMATIONS
RR90 24366102 CF, 1k ohm D471 A7568460 Diode, TVR-1B
RR91 24366102 CF, 1k ohm * D472 23316782 Diode, Zener, MTZJ6.2C
RR92 24366102 CF, 1k ohm D801 A7568754 Diode, 1S1887A FA-1
RR93 24366472 CF, 4700 ohm D802 A7568754 Diode, 1S1887A FA-1
RT61 24366332 CF, 3300 ohm D803 A7568754 Diode, 1S1887A FA-1
RT63 24366102 CF, 1k ohm D804 A7568754 Diode, 1S1887A FA-1
RV01 24366680 CF, 68 ohm D830 23316673 Diode, Zener, MTZJ5.6C
D840 A7568752 Diode, 1S1887A, FA
COILS & TRANSFORMERS D841 A7568752 Diode, 1S1887A, FA
L101 23289220 Coil, Peaking, TRF4220AF D842 23316678 Diode, Zener, MTZJ6.8B
L203 23289846 Coil, Peaking, TRF4101AT D843 23316671 Diode, Zener, MTZJ5.6A
L301 23103880 Coil (Ferrite Bead), TEM2011Y D845 23118486 Diode, ERA15-02, G1
L410 23103880 Coil (Ferrite Bead), TEM2011Y DB03 23358522 Diode (LED), SIR-56SB3F
* L462 23231292 Deflection Yoke, TDY-320UG DB30 23118859 Diode, 1SS133
* L901 23200338 Coil, Degaussing, TSB-2100CP
LA01 23289100 Coil, Peaking, TRF4100AF MISCELLANEOUS
LB01 23289470 Coil, Peaking, TRF4470AF E502 23451933 Rubber Wedge
T401 23224983 Transformer, Horiz. Drive, F301 23144727 Fuse, 0.4A
TLN1039 F301A 23165433 Holder, Fuse
* T461 23236614 Transformer, Flyback, F470 23144495 Fuse, 0.8A
TFB4139AD F470A 23165433 Holder, Fuse
T801 23211696 Line, Filter, TRF3216AK F801 23144888 Fuse, 5.0A, 125V
F801A 23165433 Holder, Fuse
SEMICONDUCTORS F802 23144785 Fuse, 1.25A, 125V
Q301 B0377890 IC, TA8403K F802A 23165433 Holder, Fuse
Q301B 72471082 Screw, BRDT2W3X10 SZN G060 24366101 CF, 100 ohm
Q402 A6330069 Transistor, 2CS2482 FA-1 G411 23103880 Coil (Ferrite Bead), TEM2011Y
Q404 A6873824 Transistor, 2SD2599 G885 23248031 Coil, Choke, TLN3274D
Q404B 72471082 Screw, BRDT2W3X10 SZN G903 23118859 Diode, 1SS133
Q421 23905952 IC, MC7809BT P001 23142041 Terminal, Antenna Shield
Q471 23114530 Transistor, 2SA933S-Q P801 23372112 Power Cord
Q472 23114528 Transistor, 2SC1740S, Q SA01 23145227 Switch, Push, 1C1P
Q501 B0385424 IC, TA1223AN SA02 23145227 Switch, Push, 1C1P
Q610 23119668 IC, TDA2611A SA03 23145227 Switch, Push, 1C1P
* Q801 23114420 IC, STR30134 SA04 23145227 Switch, Push, 1C1P
Q801B 70391356 Screw, BITTB3X10 SZN SA05 23145227 Switch, Push, 1C1P
Q817 23114528 Transistor, 2SC1740S, Q SA07 23145227 Switch, Push, 1C1P
Q818 A6012010 Transistor, RN2201 SR81 23146566 Relay, DC48V
Q819 23114528 Transistor, 2SC1740S, Q * V901A 23902970 Socket, CRT, 8P
Q830 23114552 Transistor, 2SC1685-Q, TH V901M 23102462 Magnet, Purity-Convergence,
Q843 A6330059 Transistor, 2SC2482(C) MAG-1104
Q901 A6330059 Transistor, 2SC2482(C) W661 23351157 Speaker, SPK-1399,
Q902 A6330059 Transistor, 2SC2482(C) 50x90mm, 8 ohm
Q903 A6330059 Transistor, 2SC2482(C) X401 23153721 Ceramic Resonator, 503kHz,
Q971 A6534040 Transistor, 2SA1015-Y TCR1023
QA01 23000286 IC, TMPA8700CKN-1A04 X501 23153961 Crystal, 3.58MHz
QA02 70129473 IC, AT24C01A10PC
– 21 –
Location Location
Part No. Description Part No. Description
No. No.
TCR1056BM
Z001 23134187 CR-GAP, CRA112G
PC BOARD ASSEMBLIES
* M051Z Main Board, PB9391A-1
* M052Z CRT Drive Board, PB9391A-2
PICTURE TUBE
* V901 23312676 Picture Tube, A48KZL70X(LW)
TUNER
H001 23321369 Tuner, EL953L
ACCESSORIES
K912 23306309 Remote Hand Unit, CT-9988
SPECIFIC INFORMATIONS
CABINET PARTS
– 22 –
MAIN BOARD PB9391-1
BOTTOM (FOIL) SIDE
– 23 – – 24 –
CRT-D DRIVE BOARD PB9391-2 TERMINAL VIEW OF TRANSISTORS
BOTTOM (FOIL) SIDE
B
C
E
E
BC E
BC
– 25 – – 26 –
MEMO
........................................................................................................................................
GENERAL ADJUSTMENTS
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
SPECIFIC INFORMATIONS
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
– 27 –
MEMO
........................................................................................................................................
GENERAL ADJUSTMENTS
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
SPECIFIC INFORMATIONS
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
– 28 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SPECIFICATIONS
– 29 –
SCHEMATIC DIAGRAM
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY
PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL.
CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this
model. Do not degrade the safety of the receiver through improper servicing.
NOTE:
1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5%
tolerance carbon resistor, unless otherwise noted as the following marks.
1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt
1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt
K = ±10% G = ±2% F = ±1%
2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in
?F, and the values more than 1 in pF.
All capacitors are ceramic 50V, unless otherwise noted as the following marks.
Electolytic capacitor Mylar capacitor
3. The parts indicated with " * " have special characteristics, and should be replaced with identical parts only.
4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all
controls at normal, line voltage 120 volts.
5. Waveforms are taken receiving color bar signal with enough sensitivity.
6. Voltage reading shown are nominal values and may vary ±20% except H.V.
SCHEMATIC DIAGRAM MODEL : 19A20 Chassis No. TAC0001
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY NOTE:
PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. 1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5% 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all
tolerance carbon resistor, unless otherwise noted as the following marks. controls at normal, line voltage 120 volts.
CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components 1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt 5. Waveforms are taken receiving color bar signal with enough sensitivity.
which have special characteristics important for safety and should be replaced only with types identical to those in the 1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt 6. Voltage reading shown are nominal values and may vary ±20% except H.V.
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals. K = ±10% G = ±2% F = ±1%
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this 2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in
model. Do not degrade the safety of the receiver through improper servicing.
?F, and the values more than 1 in pF.
All capacitors are ceramic 50V, unless otherwise noted as the following marks.
Electolytic capacitor Mylar capacitor
3. The parts indicated with " * " have special characteristics, and should be replaced with identical parts only.
FILE NO. 020-200003
SERVICE MANUAL
COLOR TELEVISION
N0E Chassis
19A20 (TAC0001)
TOSHIBA CORPORATION
1-1, SHIBAURA 1- CHOME, MINATO-KU, TOKYO 105-8001, JAPAN