B.tech Me Final1
B.tech Me Final1
B.tech Me Final1
Scheme
of
Bachelor of Technology
(Mechanical Engineering)
[Effective from Session 2015 - 2016]
I.E.C. UNIVERSITY
BADDI (SOLAN) H.P.
IEC University, Baddi
SCHEME OF STUDY & EVALUATION FOR
B. TECH. PROGRAM
FIRST YEAR,
(Common for all branches)
SEMESTER I
Course Periods Evaluation Scheme Course Total
Sr. No Code Title L T P Sessional Marks Exam Marks Credits
marks
MSE CA P Total ESE
Theory
1 EE-101/ Basic Electrical 3 1 0 30 15 0 45 30 75 3.5
ME-101 Engineering/
Engineering
Mechanics
2 ECE- Basic Electronics 3 1 0 30 15 0 45 30 75 3.5
101/ Engineering/
ME-102 Engineering Graphics
3 MAT- Engineering 3 1 0 40 20 0 60 40 100 3.5
101 Mathematics-1
4 CSE-101 Fundamentals of 3 1 0 30 15 0 45 30 75 3.5
computer and
programming in “C”
5 HUM- Communication 2/ 0 0 30/ 15/ 0 45/ 30/ 75/ 2/
101/ Skills/ Environment 3 / 0 40 20 0 060 40 100 3
EVS-101 Science and 1
technology
6 PHY- Engineering Physics/ 3 1 0 30 15 0 45 30 75 3.5
101/ Engineering
CHE-101 Chemistry
Practical/Training/Project
1 PHY- Engineering Physics 0 0 2 15 15 10 25 1
151/ Lab./ Engineering
CHE-151 Chemistry Lab
2 CSE-151 Programming in “C” 0 0 2 15 15 10 25 1
lab.
3 ECE- Basic Electronics 0 0 2 15 15 10 25 1
151/ Engineering Lab/
ME-151 Engineering
Mechanics Lab
4 EE-151/ Basic Electrical 0 0 2 15 15 10 25 1
ME-152 Engineering Lab/
Workshop Lab
5 HUM- Communication Skills 0 0 2 15 15 10 25 1
151 Lab
Total 18 6 8 200 100 60 360 240 600 24.5
SEMESTER II
Theory
1 MAT- Engineering 3 1 0 40 20 0 60 40 100 3.5
201 Mathematics-II
2 PHY- Engineering Physics/ 3 1 0 30 15 0 45 30 75 3.5
101/ Engineering
CHE-101 Chemistry
3 EE-101/ Basic Electrical 3 1 0 30 15 0 45 30 75 3.5
ME-101 Engineering/
Engineering
Mechanics
COMPONENTS OF EVALUATION
The components of Evaluation for each course will be as under:
For Non-Practical Subjects:
(a) Continuous A ssessment (CA), -- 20 Marks in the form of:
(i) Assignments (15 Marks)
(ii) Attendance (05 Marks),
(b) Mid-Term Exams (MSE), ---------40 Marks
(i) First MSE to be held after completion of 35% - 40% course
coverage,
(ii) Second MSE to be held after completion of 70% - 80% course
coverage
(c) End- semester Exams (ESE), ------ 40 Marks
For Subjects with Practical Courses:
(a) Continuous A ssessment (CA), -- 15 Marks in the form of:
(i) Assignments (10 Marks)
(ii) Attendance (05 Marks),
(b) Mid-Term Exams (MSE), ---------30 Marks
(i) First MSE to be held after completion of 35% - 40% course
coverage,
(ii) Second MSE to be held after completion of 70% - 80% course
coverage
(c) End- semester Exam (ESE), ------ 30 Marks
For Practical Courses:
(a) Continuous A ssessment (CA) -- 15 Marks
(b) End-semester Practical Exam----10
Total --25 Marks
B.Tech (Mechanical Engineering)
Semester III
Note- Summer Training (6 Weeks) done after 4th Semester would be evaluated in 5th semester through
Report and viva voice etc
B.Tech (Mechanical Engineering)
Semester V
Unit-II (Lectures 6)
FUELS: Introduction, classification, solid, liquid and gas fuel; Nuclear energy- Breeder reactor and light
water nuclear reactor for power generation (Block diagram only), solar energy conservation and solar
cells; Fuel Cells- Introduction, types and their characteristics, alternate fuels.
LUBRICANTS: Introduction, Mechanisms of lubrication, Types and selection of lubricants, synthetic
lubricants, properties and different methods for testing of lubricating oils and greases.
Unit-III (Lectures 7)
POLYMERS: Introduction, classification, types of polymerization, synthesis and applications of some
important polymers. PVC, Polyamides, Polyurethane, Polyethylene, Poly propylene, PET, Resins
(Phenol Formaldehyde), PMMA, PAN. Conducting and Biodegradable polymers ; Introduction:
Rubber and different types of rubber, Vulcanization of rubber. Natural and synthetic rubber. Some
important rubber and its uses.
References:
1. Vogel’s quantitative Analysis A I Vogel, G Svelha Seventh Edition longman Group ltd.
2. Elementary Practical Organic Chemistry Fifth Edition Quantitave analysis, A I Vogel,
Longman Group Ltd.
3. Practical Eng. Chemistry S. S. Dara , First edition S. Chand Company.
4. Engg. Chemistry Sudha Rani and S.K. Bhasin First edition Dhanpat rai Publication.
5. Saltcomindia.gov.in./NIDCCP- EstimatContent.html
B.Tech. Common for all branches of Engineering
Semester I
ENVIRONMENTAL SCIENCE AND TECHNOLOGY
Course Code: EVS-101 L T P
2 0 0
Unit I (10 hours)
INTRODUCTION: Definition and Scope: Importance, Public awareness and education.
Natural Resources: Introduction, Renewable and non-renewable, Forest, water, mineral, food,
energy and land resources, Conservation of resources, Equitable use of resources.
Human population and the environment: Population growth, Environment and human health,
Human rights, HIV/AIDS, Value education, Women and child welfare.
Unit II (7 hours)
ECOLOGY: Ecosystems, Concept, Structure, Function, Energy flow, Ecological pyramids,
Forest, grassland, desert and aquatic ecosystems - Introduction, characteristic features, structure
and function.
Biodiversity: Genetic, Species and ecological diversity, Threats to biodiversity, Conservation of
Biodiversity.
Unit IV (6 hours)
ENVIRONMENTAL CHEMISTRY
General Chemistry: Review of concepts like oxidation-reduction, Gas laws, pH and Buffers.
Atmospheric Chemistry: Photochemical reactions in atmosphere, Major chemical pollutants
and their effects.
Water and Wastewater Chemistry: Hardness, Residual chlorine, Dissolved oxygen, BOD,
COD, Solids.
Green Chemistry: Principles, Green materials, reactions, reagents and product.
Text Books:
• Environmental Studies by J.P.Sharma.
• Environmental studies by Smriti Srivastava.
Reference Books:
• Environment and Ecology by H.Kaur.
• Environmental Studies by Ranjit Daniels.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: MAT-101 ENGINEERING MATHEMATICS I L T P
3 1 0
Unit-III Integral Calculus: Surface and volume of solids of revolutions, Double integral,
double integral by changing into polar form, area and volume by double integration, beta
function and gamma function (simple properties).
Unit-IV Differential Equations: Differential Equations of first order and first degree, linear
form, reducible to linear form, exact form and linear differential equation of higher order with
constant coefficient only.
Unit-V Differential Equations: Second order ordinary Differential Equations with variables
Coefficients, homogeneous and exact forms, change of dependent variable, change of
independent variable, method of variation of parameters.
Text Books:
1. Higher Engineering Mathematics, H.K. Dass, S.Chand.
2. A Text Book of Engineering Mathematics, N.P. Bali, Luxmi Publication.
3. Higher Engineering Mathematics, Dr. BS Grewal.
References:
1. Higher Engineering Mathematics, B.V. Ramana, Tata McGraw Hill.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: ECE-101 BASIC ELECTRONICS ENGINEERING L T P
3 1 0
Unit II (8 lectures)
Bipolar junction transistors: Introduction, Junction Transistor Structure, Operation, Transistor
amplifying action, CB, CC and CE Configuration, characteristics, application of transistor as an
amplifier, transistor biasing.
Unit IV (6 lectures)
Operational amplifiers: Introduction to Op-amp, Inverting and non-inverting configuration,
Op-amp applications adder, sub tractor, integrator, differentiator and comparator, practical op -
amps.
Unit V (8 lectures)
Number System and Embedded system: Binary, Octal, Hexadecimal number systems and
their inter-conversion, Embedded system, introduction to microcontroller, introduction to
microprocessor, difference between microcontroller and microprocessor, 8085 and 8051.
Text Books
1. Electronics Devices and circuits by Millman & Halkias.
2. Electronics devices and circuit theory by Robert Boylestad
3. M. Morris Mano, Digital Design, Prentice Hall of India.
4. R.S. GAONKAR, Microprocessor Architecture, Programming and applications with the
8085/8080A.
B.Tech. Common for all branches of Engineering
Semester I
BASIC ELECTRONICS ENGINEERING LAB
Course Code: ECE-151 L T P
0 0 2
List of Experiments
1. To observe sine wave, square wave, triangular wave and ramp waveforms on the C.R.O. and
to measure amplitude and frequency of the waveforms.
2. To obtain V-I characteristics of PN junction diode.
3. To study observe waveform at the output of half wave rectifier.
4. To study observe waveform at the output of full wave bridge rectifier.
5. To obtain V-I characteristics of Zener diode.
6. To draw the input and output characteristics of NPN transistor for common base
configurations.
7. To draw the input and output characteristics of NPN transistor for common Emitter
configurations.
8. To observe waveforms at the output of clamper circuits.
9. To observe waveforms at the output of clipper circuits
B.Tech. Common for all branches of Engineering
Semester I
Course Code: EE-101 BASIC ELECTRICAL ENGINEERING L T P
3 1 0
UNIT I: Introduction to Electrical Engineering: Essence of electricity, Conductor,
semiconductor and insulator; Electric Field, Electric Current, Potential and Potential difference,
Electromotive Force, Electric Power, Ohm’s law, Basic circuit component and Faradays law
Electromagnetic Induction.
UNIT II: Network Analysis: Basic definition, type of elements, type of sources, Resistive
Network, Inductive Network, Capacitive Network, series parallel circuits, star-delta and delta-
star transformation. Network theorems: Norton’s, Superposition, Thevenin’s, Maximum Power
Transfer Theorem in dc circuit with simple problem.
UNIT III: Magnetic Circuits: Basic definitions, Analogy between electric and magnetic circuits,
series magnetic circuit, parallel magnetic circuit, magnetic circuits with air gap, self-inductance
and mutual inductance, magnetic coupling, coefficient of coupling.
UNIT IV: Study of AC circuits consisting of pure resistance, pure inductance, pure capacitance
and corresponding voltage current phasor diagram and waveforms, Development of concept of
reactance. Study of series R-L, R-C, R-L-C circuit and resonance, study of parallel RL,RC and
RLC circuit, concept of impedance, admittance, conductance and susceptance in case of above
combination and relevant voltage-current phasor diagrams, concept of active, reactive and
apparent power, power factor.
UNIT V: Basic concept of transformers and rotating electrical machines (operating principle,
construction and working ), Basic instrument: Introduction, classification of instruments,
operating principles, essential features of measuring instruments, Moving Coil Permanent
Magnet (PMMC) Instruments, Moving Iron of ammeters and voltmeters (elementary treatment
only).
Text Books:
1. Basic Electrical Engineering- By M.S. Naidu and S. Kamakshiah-TMH
2. Basic Electrical Engineering- By T.K. Nagasarkar and M.S. Sukhija Oxford University
Press.
References:
1. Theory and problems of Basic Electrical Engineering by D.P. Kothari and I.J. Nagrath
PHI.
2. Principles of Electrical Engineering by V.K. Mehta, S.Chand Publications.
3. Essentials of Electrical and computer Engineering by David V. Kerns, JR. J. David Irwin
Pearson.
B.Tech. Common for all branches of Engineering
Semester I
UNIT II
Quantum Theory: Need of Quantum Mechanics, Davisson-Germer Experiment and Matter
waves, Group and Phase velocities. Uncertainity Principle and its applications, Time-
independent and Time-Dependent Schrödinger Wave equation, Eigen values and Eigen
Functions, Applications of Schrödinger Wave equation to Particle in a box (one dimensional).
UNIT III
Lasers and Optical Fibers: Spontaneous and Stimulated Emission, Einstein’s coefficients,
Population Inversion and Optical Pumping, Three-level and Four-level Lasers, Ruby, He-Ne,
CO2, Semiconductor Lasers, Application of lasers, Basic theory of fiber optics, accepatance
angle, numerical aperture, modes of propagation, material and pulse dispersion, application of
optical fibers.
UNIT IV
Magnetic materials and Superconductivity: Hard and soft magnetic materials and their
applications, Ferrites and their applications, Phenomenon of superconductivity, Magnetic
properties of superconductors (Meissner effect), Type-I and Type-II Superconductors,
Applications of Superconductivity.
UNIT V
Radiation Physics: A few X- and Gamma-radioisotopes (109Cd, 241Am, 60Co, 137Cs) and their
applications, Coolidge tube; Continuous and Characteristic X-rays; Moosley’s law; Absorption of X-rays
and gamma rays; X-ray Diffraction and Bragg’s law, EDXRF and WDXRF (qualitative idea).
B.Tech. Common for all branches of Engineering
Semester I
Course Code: PHY-151 ENGINEERING PHYSICS LAB L T P
0 0 2
List of Experiments
1. To determine the specific rotation of cane sugar solution with the help of polarimeter.
2. To determine Planck’s constant
3. To determine the dispersive power of the material of the prism using mercury light with
the help of a spectrometer.
4. To determine the wavelength of sodium light by Newton’s Ring.
5. To determine the Energy Band Gap of a Semiconductor by using Four probe method.
6. To measure the numerical aperture of the given an optical fiber.
7. To determine the specific resistance of a given wire using Carey Foster’s bridge.
8. To determine e/m ratio using Thompson’s method
9. To determine angle of divergence of Laser beam
10. To determine angle of prism and minimum deviation using spectrometer.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: ME-101 ENGINEERING MECHANICS L T P
3 1 0
Unit I (8hours)
Two Dimensional Concurrent Force Systems: Basic concepts, Units, Force systems, Laws of
motion, Moment and Couple, Vectors - Vectorial representation of forces and moments - Vector
operations. Principle of Transmissibility of forces,, Resultant of a force system, Equilibrium and
Equations of Equilibrium, Equilibrium conditions, Free body diagrams, Determination of
reaction, Resultant of Two dimensional concurrent forces, Applications of concurrent forces
Unit II (13hours)
Two Dimensional Non-Concurrent Force Systems: Basic Concept, Varignon’s theorms,
Transfer of a force to parallel position, Distributed force system, Types of supports and their
reactions, converting force into couple and Vise versa Applications.
Friction: Introduction, Laws of Coulomb Friction, Equilibrium of Bodies involving Dry-
friction, Belt friction, ladder Friction, Applications of Friction in daily life.
Structure: Plane truss, perfect and imperfect truss, assumption in the truss analysis, analysis of
perfect plane trusses by the method of joints, method of section.
Unit IV (8hours)
Kinematics of Rigid Body: Introduction, plane rectilinear motion of rigid body, Plane
curvilinear Motion of Rigid Body, Velocity and Acceleration under Translation and Rotational
Motion, Relative Velocity.
Unit V (8hours)
Kinetics of Rigid Body: Introduction, Force, Mass and Acceleration, Work and Energy,
Impulse and Momentum, D’Alembert’s Principles and Dynamic Equilibrium, Friction in
moving bodies
Text books:
1. Engineering Mechanics Statics , J.L Meriam , Wiley
2. Engineering Mechanics Dynamics , J.L Meriam , Wiley
3. Engineering Mechanics by Irving H. Shames, Prentice-Hall
4. Engineering Mechanics : Statics and Dynamics, R. C. Hibbler
5. Mechanics of Solids by Abdul Mubeen, Pearson Education Asia.
6. Mechanics of Materials by E.P.Popov, Prentice Hall of India Private limited.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: ME-151 ENGINEERING MECHANICS LAB L T P
0 0 2
List of Experiments
References:
1. Applied Mechanics and Strength of Materials, U.C. Jindal, Galgotia Publications
2. Engineering Mechanics For Uptu With Experiments, D.S. Kumar, S.K. Kataria
publication
3. Advanced Practical Physics for Students, Worsenop & Flint
B.Tech. Common for all branches of Engineering
Semester I
Course Code: ME-102 ENGINEERING GRAPHICS L T P
3 1 0
Unit I (10hours)
Introduction: Sheet layout, Drawing instruments and their uses, Lettering and free hand
practicing, Dimensioning, Types of lines, BIS conventions.
Unit II (12hours)
Orthographic projections: Definitions, Planes of projection, Reference line and convention
employed, Projections of points, lines, True and apparent lengths, inclinations, Orthographic
projections of plane surfaces.
Unit III (8hours)
Projections of solids: Definitions, Projections of right regular tetrahedron, Projections of
hexahedron, Projections of prisms, Projections of pyramids, cylinders and cones.
Unit IV (10hours)
Isometric projections
Isometric scales, Isometric projections of simple figures, tetrahedron, hexahedron, right regular
prisms, pyramids, cylinder and cones, Spheres, cut spheres and combination of solids.
Unit V (8 hours)
Introduction to computer aided sketching: Computer screen: layout of menus/tool bars,
Creations of 2D/3D Environment, Drawing scale, units etc., Creation of shapes: square,
rectangle, circle, curves etc, Dimensioning.
Text books:
1. Engineering Drawing – N D Bhatt & V M Panchal, 48th edition, 2005 Charotar
Publishing House, Gujarat.
2. A Primer on Computer Aided Engineering Drawing – 2006, Published by VTU,
Belgaum.
3. A Textbook of Engineering Graphics, K. Venugopal and V. Prabhu Raja, New Age
International Publishers.
4. Engineering Drawing and Graphics using Auto Cad, T. Jeyapoovan, Vikas Publishing
House Pvt. Ltd.
Reference Books:
1. Computer Aided Engineering Drawing – S. Trymabaka Murthy, I K International
Publishing House Pvt. Ltd., New Delhi, 3rd revised edition – 2006.
2. Engineering Graphics – K R Gopalakrishna, 32nd edition, 2005 – Subhash Publishers,
Bangalore.
3. Fundamentals of Engineering Drawing with an introduction to Interactive Computer
Graphics for Design and Production – Luzadder Warren J., duff John M., Eastern
Economy Edition, 2005 - Prentice – Hall of India Pvt. Ltd., New Delhi.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: ME-152 WORKSHOP PRACTICE L T P
0 0 3
List of Jobs
Carpentry Shop
Job No. 1
Objective: To Prepare a “T–LAP JOINT” as per sketch.
Job No. 2
Objective: To prepare a “Cross Lap Joint” as per given sketch.
Job No. 3
Objectives: To prepare Mortise and Tenon Joint
Fitting Shop
Job No. 1
Objectives: To Make Right Angle Fitting Job
Job No. 2
Objectives: To Make A Square Fitting Job.
Unit II
Listening Skills: Process of listening, Types of listening, and Barriers to effective listening,
Difference between hearing and listening, Feedback skills.
Speaking Skills: Study of Vowels symbols & diagram( Long, Short, Open, Close, Rounded,
Unrounded, Monophthongs, Diphthongs) , Consonants & symbols , Accent , Stress , Voice
Modulation
Unit III
Grammar: Abbreviations, Idioms & phrases, One word substitution, Antonyms, Synonyms,
Homophones, Homonyms, Word formation: prefix, suffix, Punctuation. Transformation of
sentences: Simple to compound, compound to Complex& vice versa.
.
Unit IV
Writing Skills: Business letters: principles, structure, Writing a memo, Job application letters,
preparing a personal resume; Writing notices, Agenda and Minutes of meetings; Paragraph
writing, Report writing: Characteristics, types of reports, structure of technical/research reports,
preparatory steps to report writing.
Text Books:
1. Bhattacharya, Inderjit, an Approach to Communication Skills. Dhanpat Rai, New Delhi.
2. K.K.Sinha, Business Communication, Galgotia Publishing Company, New Delhi, 1999.
References:
1. Sheila H.A. Smith, M and Thomas, L., Methuen, Reading to Learn; London, 1982.
2. McGraw, SJ;Basic Managerial Skills for all, Prentice Hall of India, New Delhi 1991
3. Technical Reporting Writing British Association for commercial and Industrial
Education, BACIE, 1992
4. Chrissie Wright (Ed.); Handbook of Practical Communication Skills; JAICO Books
5. Common Errors in English, by Sudha Publication (P) Ltd., B-5, Prabhat Kiran Building,
Rajendra Place, New Delhi – 110008.
6. Abul Hashem, Common Errors in English, Ramesh Pub. House, Daryagang New Delhi.
7. Objective English by Tata McGraw Hill Publishing Co. Ltd., New Delhi.
8. R.K.Bansal & J.B. Harrison, spoken English for India, Orient Longman.
9. Veena Kumar, the Sounds of English, Makaav Educational Software, New Delhi.
B.Tech. Common for all branches of Engineering
Semester I
Course Code: HUM-151 COMMUNICATION SKILLS LAB L T P
0 0 2
Practical syllabus-
a) Group Discussion
b) Just a minutes session: Speaking Extempore for one minutes on given topics
c) Reading aloud of newspaper headlines and important articles.
d) Improving pronunciation through tongue twisters.
e) Soft Skills: Mannerism or Etiquette.
f) Mock Interview
g) Preparing PPTs
h) Telephonic Skills
i) Phonetics
B.Tech. Common for all branches of Engineering
Semester I
FUNDAMENTALS OF COMPUTERS & PROGRAMMING IN “C”
Course Code: CSE-101 L T P
3 1 0
Unit I (10hours)
An Overview of Computer System: Anatomy of a digital Computer, Memory Units, Main and
Auxiliary Storage Devices, Input Devices, Output Devices, Classification of Computers,
Introduction to microprocessor, commonly used CPUs, Input/output ports and connectors. Radix
Number System: Decimal, Binary, Octal, Hexadecimal numbers
Operating System: The user Interface, Running Programmes, Managing files, Introduction to
PC operating Systems: Unix/Linux, DOS, and Windows 2000.
Unit II (10hours)
Networking Basics: Introduction to the basic concepts of Networks and Data Communications,
Network topologies, Network Types (LAN, WAN and MAN), How Internet works, Major
features of internet, Emails, FTP, Using the internet.
Programming Languages: Machine-, Assembly-, High Level- Language, Assembler,
Compiler, Interpreter, debuggers, Programming fundamentals: problem definition, algorithms,
flow charts and their symbols, introduction to compiler, interpreter, assembler, linker and loader
and their inter relationship.
Unit III (10hours)
C Programming language: C fundamentals formatted input/ output, expressions, selection
statements, loops and their applications; Basic types, arrays, union, structure, functions,
including recursive functions, program organization: local and external variables and scope,
pointers & arrays.
Unit I (10hours)
Strings: strings literals, string variables, I/O of strings, arrays of strings; applications.
Structures, Unions and Enumerations: Structure variables and operations on structures;
Structured types, nested array structures; unions; enumeration as integers, tags and
types. Standard library: Input / output; streams, file operations, formatted I/O, character
I/O, line I/O, block, string I/O, Library support for numbers and character data, error
Handling:
TEXT BOOKS:
1. Using Information Technology, 5th Edi, Brian K Williams & Stacey C. Sawyer, 2003, TMH
2. The C Programming Language by Dennis M Ritchie, Brian W. Kernigham, 1988, PHI.
3. C Programming – A modern approach by K.N. King, 1996, WW Norton & Co.
4. Fundamentals of Computing and C Programming, R. B. Patel, Tech Publications, New Delhi.
B.Tech. Common for all branches of Engineering
Semester I
FUNDAMENTALS OF COMPUTERS & PROGRAMMING IN “C” LAB
Course Code: CSE-151 L T P
0 0 2
List of Experiments
Unit II (10hours)
Vector Calculus: Scalar and vector field, Differentiation & Integration of vector functions,
Gradient of a scalar field and directional derivative, Divergence and Curl of a vector field, Line
integral, Surface integral and volume integral. Application of Vector Calculus: Green’s
Theorem, Gauss’s Theorem and Stoke’s Theorem (without proof) and their Applications.
Unit IV (9hours)
Partial differential equations: Formation of partial differential equations, Lagrange’s linear
partial differential equations, First order non-linear partial differential equations
{ f ( p, q ) 0, z px qy f ( p, q ), f ( z , p, q ) 0, f1 ( x, p ) f 2 ( y, q ) }, Charpit’s method
Unit V (9hours)
Application of Partial differential equations: Homogeneous linear equations with constants
coefficients, Non-homogeneous linear partial differential equations, Method of separation of
variables and its application, One dimensional wave equation, One dimensional heat equation.
Suggested Readings:
Unit II
Classes and Data Abstraction: Introduction, Structure Definitions, Accessing Members of
Structures, Class Scope and Accessing Class Members, Initializing Class Objects: Constructors,
Using Default Arguments With Constructors, Using Destructors, Classes: Const (Constant)
Object And Const Member Functions, Object as Member of Classes, Friend Function and Friend
Classes, Using This Pointer, Dynamic Memory Allocation with New and Delete, Static Class
Members, Function overloading.
Operator Overloading: Introduction, Fundamentals of Operator Overloading, Restrictions On
Operators Overloading, Operator Functions as Class Members vs. as Friend Functions,
Overloading, <<, >> Overloading Unary Operators, Overloading Binary Operators.
Unit III
Inheritance: Introduction, Inheritance: Base Classes and Derived Classes, Protected Members,
Casting Base- Class Pointers to Derived- Class Pointers, Overriding Base –Class Members in a
Derived Class, Public, Protected and Private Inheritance, Using Constructors and Destructors in
derived Classes.
Virtual Functions and Polymorphism: Introduction to Virtual Functions, Abstract Base
Classes and Concrete Classes, Polymorphism, New Classes and Dynamic Binding, Virtual
Destructors, Polymorphism, Dynamic Binding. Files and I/O Streams: Files and Streams,
Creating a Sequential Access File, e.g. , Random Access Files, Creating A Random Access File,
e.g. Stream Input/output Classes and Objects, e.g., Stream Manipulators.
Unit IV
Templates & Exception Handling: Function Templates, Class Template, Templates and
Inheritance, Basics of C++ Exception Handling: Try, Throw, Catch, Throwing an Exception,
Catching an Exception, Re-throwing an Exception
Text Books:
• C++ How to Program by H M Deitel and P J Deitel, 1998, Prentice Hall
• Object Oriented Programming in Turbo C++ by Robert Lafore ,1994, The WAITE Group
Press.
• Programming with C++ By D Ravichandran, 2003, T.M.H
Reference books: • Object oriented Programming with C++ by E Balagurusamy, 2001, Tata
McGraw-Hill
• Computing Concepts with C++ Essentials by Horstmann, 2003, John Wiley,
• The Complete Reference in C++ By Herbert Schildt, 2002, TMH.
B.Tech. Common for all branches of Engineering
Semester I
PROGRAMMING IN ‘C++’ LAB
Course Code: CSE-251 L T P
0 0 2
List of Experiments
Unit II (10hours)
Vector Calculus: Scalar and vector field, Differentiation & Integration of vector functions,
Gradient of a scalar field and directional derivative, Divergence and Curl of a vector field, Line
integral, Surface integral and volume integral. Application of Vector Calculus: Green’s
Theorem, Gauss’s Theorem and Stoke’s Theorem (without proof) and their Applications.
Unit IV (9hours)
Partial differential equations: Formation of partial differential equations, Lagrange’s linear
partial differential equations, First order non-linear partial differential equations
{ f ( p, q ) 0, z px qy f ( p, q ), f ( z , p, q ) 0, f1 ( x, p ) f 2 ( y, q ) }, Charpit’s method
Unit V (9hours)
Application of Partial differential equations: Homogeneous linear equations with constants
coefficients, Non-homogeneous linear partial differential equations, Method of separation of
variables and its application, One dimensional wave equation, One dimensional heat equation.
Suggested Readings:
Unit II
Classes and Data Abstraction: Introduction, Structure Definitions, Accessing Members of
Structures, Class Scope and Accessing Class Members, Initializing Class Objects: Constructors,
Using Default Arguments With Constructors, Using Destructors, Classes: Const (Constant)
Object And Const Member Functions, Object as Member of Classes, Friend Function and Friend
Classes, Using This Pointer, Dynamic Memory Allocation with New and Delete, Static Class
Members, Function overloading.
Operator Overloading: Introduction, Fundamentals of Operator Overloading, Restrictions On
Operators Overloading, Operator Functions as Class Members vs. as Friend Functions,
Overloading, <<, >> Overloading Unary Operators, Overloading Binary Operators.
Unit III
Inheritance: Introduction, Inheritance: Base Classes and Derived Classes, Protected Members,
Casting Base- Class Pointers to Derived- Class Pointers, Overriding Base –Class Members in a
Derived Class, Public, Protected and Private Inheritance, Using Constructors and Destructors in
derived Classes.
Virtual Functions and Polymorphism: Introduction to Virtual Functions, Abstract Base
Classes and Concrete Classes, Polymorphism, New Classes and Dynamic Binding, Virtual
Destructors, Polymorphism, Dynamic Binding. Files and I/O Streams: Files and Streams,
Creating a Sequential Access File, e.g. , Random Access Files, Creating A Random Access File,
e.g. Stream Input/output Classes and Objects, e.g., Stream Manipulators.
Unit IV
Templates & Exception Handling: Function Templates, Class Template, Templates and
Inheritance, Basics of C++ Exception Handling: Try, Throw, Catch, Throwing an Exception,
Catching an Exception, Re-throwing an Exception
Text Books:
• C++ How to Program by H M Deitel and P J Deitel, 1998, Prentice Hall
• Object Oriented Programming in Turbo C++ by Robert Lafore ,1994, The WAITE Group
Press.
• Programming with C++ By D Ravichandran, 2003, T.M.H
Reference books: • Object oriented Programming with C++ by E Balagurusamy, 2001, Tata
McGraw-Hill
• Computing Concepts with C++ Essentials by Horstmann, 2003, John Wiley,
• The Complete Reference in C++ By Herbert Schildt, 2002, TMH.
B.Tech. Common for all branches of Engineering
Semester I
PROGRAMMING IN ‘C++’ LAB
Course Code: CSE 251 L T P
0 0 2
List of Experiments
MATHEMATICS – III
Question Paper will contain three sections of 100 marks, Section (A) is compulsory & will
contain 10 short questions each carrying weightage of 2 marks(Fill in the blanks/ True –false/
MCQ/One Word answer)
Section B will contain question no 2 and 3. Each question will have six sub questions and
candidate will attempt any four questions from each question carrying weightage of 5 marks.)
Section C will contain question no 4 and 5. Each question will have four sub questions and
candidates will attempt any two questions from each question carrying weightage of 10
marks.
UNIT-I Fourier Series: Periodic functions, Fourier series of period 2 , Euler’s formulas, Dirichlet’s
condition, Fourier series for discontinuous functions, Change of interval, Odd and even function, Half-
range sine and cosine series.
UNIT-II Fourier Transforms: Fourier integrals, Fourier transforms, Fourier cosine and sine transforms,
Properties of Fourier transforms, Convolution theorem, Perseval’s identity, Relation between Fourier and
Laplace transforms, Fourier transforms of the derivatives of a function, Application to boundary value
problems.
UNIT-IV Numerical analysis: Solution of algebraic and transcendental equations by the Bisection,
Regula-falsi and Newton-Raphsion methods, Solution of linear simultaneous equations by Gauss
elimination method, Iteration methods, Jacobi’s iteration method, Gauss-seidel method, Relaxation
method, Numerical integration methods, Trapezoidal rule, Simpson’s one-third rule, Simpson’s three-
eighth rule, Numerical solution of differential equations, Picard’s method, Taylor’s series method, Euler’s
method and forth-order Runge-Kutta method.
Unit II
Kinematics of Fluid Flow: Velocity of Fluid, Streamlines, Path Lines and Streak Lines, Equation of Continuity,
One-, Two-, Three-dimensional Flows, Flow Net, Uses and Limitations.
Dynamics of Fluid Flow: Energy of Fluids, Kinetic Energy Factor, Internal Energy, Energy Equation for Liquids,
Gases and Vapours, External Work done on Fluid; Introduction to Navier-Stokes Equations, Euler’s Equation along
a Streamline, Bernoulli's Equation, Examples of Application of Bernoulli’s Equation., Cavitation, Pitot Tube,
Energy and Hydraulic Grade Lines for various pipe and open channel flow cases. Free Vortex, Rotational and
Irrotational Motion; Momentum Equation and applications. (8 Hours)
Unit III
Viscous Flow: Flow Between Parallel Boundaries, Free Surface Flow over Inclined Surface, Flow Between a
Moving and Stationary Boundary, Flow through Circular Tubes, Stokes’ Law, Oiled Bearings, Viscosity
Measurements and Viscometers.
Dimensional Analysis and Similarity laws: Dimensional Analysis, Development of Equations, Buckingham's Pi
Theorem, Examples. Similarity of Flows: Geometric, Kinematic and Dynamic Similarities; Reynolds, Froude,
Weber and Mach Similarity Laws & Applications (8 Hours)
Unit IV
Real Fluid Flow: Turbulent Flow, Boundary Layer, Flow past Solid Boundaries and through Pipes, Boundary
Layers in Pipes, Separation of Boundary Layer, Examples, Secondary Flows.
Pipe Flow: Laminar and Turbulent Flow, Equation for Flow and Head Loss, Velocity Distribution for Turbulent
Flow in Smooth Pipes and Rough Pipes, Universal Chart for Pipe Friction Factors, Approximate Equations for Pipe
Friction and Head Loss, Chezy’s, Manning’s and Hazen Williams Formulae, Friction Factor in Non-Circular
Conduits, Minor Losses - Sudden and Gradual Enlargement and Contraction, Pipe Entrances, Bends, Losses in Pipe
Fittings, Pipeline Problems, Pipes in Series and parallel, Method of Equivalent Pipes, Siphon, Pipeline with a
Pump, Pipeline with Turbine, Economical Pipe Diameter.
Flow in Open Channels: Hydraulic and Energy Gradient, Steady Uniform Flow, Kutter, Bazin and Manning
Formulae, (8 Hours)
Unit V
Fluid Measurements: Measurement of Fluid Properties, Measurement of Static Pressure, Velocity Measurement,
Mechanical and Chemical Devices. Measurement of Discharge: Discharge Through an Orifice, Energy Loss,
Orifice Flow for Pressures Other than Atmospheric, Discharge Through Large Openings under Small Heads,
Coefficients, Short Tubes, Mouthpieces, Nozzles, Discharge under Gates; Discharge Through an Orifice Meter,
Flow Nozzle, Ventura Meter, Comparison, Elbow Meter, Rotameter, Displacement Meters, Inferential Meters; Open
Channel Flow Measurements, Rectangular, Contracted, Triangular, Trapezoidal, Proportional or Sutro Weirs.
(8 Hours)
Text Books:
1. M.Manohar, P.Krishnamachar, Fluid Mechanics, vol.1, SBPRA Pub. Huston, USA, 2013.
2. Vennard and Street, Fluid Mechanics
3. R J Fox, Introduction to Fluid Mechanics,
4. Hunter Rouse John Wiley and sons,Elementary Mechanics of Fluids, Omc/1946
Reference Books:
1. L H Shames Mechanics of Fluids, McGraw Hill, Internatioal student edition.
2. K L Kumar, Engineering Fluid Mechanics
3. V Gupta and S K Gupta, Fluid Mechanics and its applications, Wiley Eastern
4. Som and Biswas, Introduction to Fluid Mechanics and Machines, TMH
5. Modi and Seth, Fluid Mechanics and Fluid Machines .
6. Bruce R.Donald F Young and T H Okishi, Fundamentals of Fluid Mechanics, Wiley Eastern
B.Tech. Mechanical Engineering
Semester III
MATERIAL SCIENCE IN ENGINEERING
Course Code: ME-302 L T P Cr
3 0 0 3
UNIT I
Introduction: Historical perspective, importance of materials. Brief review of modern & atomic concepts in
Physics and Chemistry, Atomic models, Periodic table, Chemical bonding
Crystallography and Imperfections: Concept of unit cell space lattice, Bravais lattices, common crystal
structures, Atomic packing factor and density. Miller indices, X-ray crystallography techniques, Imperfections,
Defects & Dislocations in solids (10 Hours)
Unit-II
Mechanical properties and Testing: Stress strain diagram, Ductile & brittle material, Stress vs strength.
Toughness, Hardness, Fracture, Fatigue and Creep, Testing such as Strength testing, Hardness testing, Impact
testing, Fatigue testing Creep testing, Non-destructive testing (NDT)
Micro structural Exam: Microscope principle and methods. Preparation of samples and Microstructure exam and
grain size determination. Comparative study of microstructure of various metals & alloys such as Mild steel, CI,
Brass
Phase Diagram and Equilibrium Diagram: Uniary and Binary diagrams, Phase rules. Types of equilibrium
diagrams: Solid solution type, eutectic type and combination type. Iron-carbon equilibrium diagram
(8 Hours)
Unit-III
Ferrous materials: Brief introduction of iron and steel making furnaces. Various types of carbon steels, alloy steels
and cast irons, its properties and uses.
Heat Treatment: Various types of heat treatment such as Annealing, Normalizing, Quenching, Tempering and
Case hardening. Time Temperature Transformation (TTT) diagrams.
Non-Ferrous metals and alloys: Non-ferrous metals such as Cu, Al, Zn, Cr, Ni etc. and its applications, Various
type Brass, Bronze, bearing materials, its properties and uses. Aluminum alloys such as Duralumin. Other advanced
materials/alloys. (8 Hours)
Unit-IV
Magnetic properties: Concept of magnetism - Dia, Para, Ferro Hysteresis. Soft and hard magnetic materials,
Magnetic storages
Electric properties: Energy band concept of conductor, insulator and semi-conductor. Intrinsic & extrinsic semi-
conductors. P-n junction and transistors. Basic devices and its application, Diffusion of Solid, Super conductivity
and its applications, Messier effect, Type I & II superconductors, High Tc superconductors. (8 Hours)
Unit-V
Ceramics : Structure types and properties and applications of ceramics.
Mechanical/Electrical behavior and processing of Ceramics
Plastics: Various types of polymers/plastics and its applications. Mechanical behavior and processing of plastics,
Future of plastics
Other materials : Brief description of other material such as optical and thermal materials concrete,
Composite Materials and its uses. Brief introduction to Smart- materials & Nano-materials and their potential
applications
Performance of materials in service: Brief theoretical consideration of Fracture, Fatigue, and Corrosion and its
control. (8 Hours)
References:
1. W.D. Callister, Jr, - Material Science & Engineering Addition-Wesley Publication.
2. K.M.Gupta, Materials Science, Umesh Publication.
3. Van Vlash - Elements of Material Science & Engineering John Wiley & Sons.
4. V. Raghvan - Material Science, Prentice Hall.
5. Narula - Material Science, TMH.
6. Srivastava, Srinivasan - Science of Materials Engineering, NewAge Publication.
B.Tech. Mechanical Engineering
Semester III
Strength of Materials-I
Course Code: ME-303 L T P Cr
3 1 0 3.5
Unit –I
Simple, Compound Stresses and Strains: Stress and Strain and their types, Hook’s law, longitudinal and
lateral strain, Poisson’s ratio, stress-strain diagram for ductile and brittle materials, extension of a bar due
to without and with self weight, bar of uniform strength, stress in a bar, elastic constants and their
significance, relation between elastic constants, Young’s modulus of elasticity, modulus of rigidity and
bulk modulus. Temperature stress and strain calculation due to axial load variation of temperature in single
and compound bars.
(Hours 10)
Unit –II
Two dimensional stress system, stress at a point on a plane, principal stresses and principal planes, Mohr’s
circle of stress ellipse of stress and their applications. Generalized Hook's law, principal stresses related to
principal strains.
(Hours 6)
Unit –III
Bending Moment (B.M) and Shear Force (S.F) Diagrams: S.F and B.M definitions; relation between
load, shear force and bending moment; B.M and S.F diagrams for cantilevers, simply supported beams
with or without overhangs, and calculation of maximum B.M and S.F and the point of contra flexure under
the following loads: a) Concentrated loads b) Uniformity distributed loads over the whole span or part of
span c) Combination of concentrated and uniformly distributed load d) Uniformly varying loads e)
Application of moments
(Hours 10)
Unit –IV
Bending Stresses In Beams: Assumptions in the simple bending theory; derivation of formula and its
application to beams of rectangular, circular and channel, I and T- sections. Combined direct and bending
stresses in afore-mentioned sections, composite / flitched beams.
Shear stresses in beams: Shear stress distribution in rectangular, circular, I, T and channel section; built
up beams. Shear centre and its importance.
(Hours 8)
Unit –V
Slope and deflection: Relationship between moment, slope and deflection; method of integration,
Macaulay’s method, moment area method and use of these methods to calculate slope and deflection for
the following: a) Cantilevers b) Simply supported beams with or without overhang c) Under concentrated
loads, uniformly distributed loads or combination of concentrated & uniformly distributed loads.
Columns and struts: Introduction, failure of columns, Euler’s formula, Rankine-Gordon’s formula,
Johnson’s empirical formula for axially loaded columns and their applications.
(Hours 10)
Unit – I:
Fundamental Concepts and Definitions: Introduction and definition of thermodynamics,
Dimensions and units, Microscopic and Macroscopic Systems, approach system surroundings
and universe, Concept of continuum, Control system boundary, control volume and control surface,
Properties and state, Thermodynamic properties, Thermodynamic path, process and cycle,
Thermodynamic equilibrium, Reversibility and irreversibility, Quasi static process, Energy and its
forms, Work and heat, Gas laws, Ideal gas, Real gas, Law of corresponding states, Dalton’s law,
Amagat’s law, Property of mixture of gases.
(8 Hours)
Unit – II:
Zeroth law of thermodynamics: Zeroth law of thermodynamics, Temperature and its’measurement,
Temperature scales.
First law of thermodynamics: Thermodynamic definition of work, Thermodynamic processes,
Calculation of work in various processes and sign convention, Non-flow work and flow work, Joules’
experiment, First law of thermodynamics, Internal energy and enthalpy, First law of thermodynamics
applied to open systems, Steady flow systems and their analysis, Steady flow energy equation, Boilers,
Condensers, Turbine, Throttling process, Pumps etc. First law analysis for closed system (non flow
processes), Analysis of unsteady processes such as filling and evacuation of vessels with and without
heat transfer, Limitations of first law of thermodynamics, PMM-I.
(10 Hours)
Unit – III
Second law: Devices converting heat to work, Thermal reservoir, Heat engines, Efficiency,
Devices converting work to heat, Heat pump, refrigerator, Coefficient of Performance, Reversed
heat engine, Kelvin Planck statement of second law of thermodynamics, Clausius statement of
second law of thermodynamics, Equivalence of two statements of second law of thermodynamics,
Reversible and irreversible processes, Carnot cycle and Carnot engine, Carnot theorem and it’s
corollaries, thermodynamic temperature scale, PMM-II. (8 Hours)
Unit – IV
Entropy : Clausius inequality, Concept of Entropy, Entropy change in different thermodynamic
processes, Tds equation, Principle of entropy increase, T-S diagram, Statement of the third law of
thermodynamics.
Availability and Irreversibility: Available and unavailable energy, Availability and Irreversibility,
Second law efficiency, Helmholtz & Gibb’s function. (8 Hours)
Unit –V
Properties of steam and thermodynamics cycles: Pure substance, Property of steam, Triple
point, Critical point, Sub-cooled liquid, Saturation states, Superheated states, Phase transformation
process of water, Graphical representation of pressure, volume and temperature, P-T & P-V diagrams,
T-S and H-S diagrams, use of property diagram, Steam-Tables & Mollier charts, Dryness factor
and it’s measurement, processes involving steam in closed and open systems. Simple Rankine cycle.
(8 Hours)
Books:
1. Engineering Thermodynamics by Jones and Dugans, PHI Learning Pvt. Ltd.
2. Fundamentals of Thermodynamics by Sonntag, Wiley India Pvt. Ltd.
3. Fundamentals of Classical Thermodynamics by Van Wylen, John wiley & sons.
4. Thermodynamics by J.P. Holman, McGraw Hill.
5. Engineering Thermodynamics by P.K.Nag, Tata Mc Graw Hill Pub.
6. Engineering Thermodynamics by Onkar Singh, New Age International Pub..
7. Thermal Engineering By R.K. Rajput, Laxmi Publication.
8. Engineering Thermodynamics by C.P. Arora.
B.Tech. Mechanical Engineering
Semester III
HUMAN VALUES & PROFESSIONAL ETHICS (ME-305)
L T P Cr
3 0 0 3
Unit 1
Introduction - Understanding the need of Value Education, Self Exploration as the
process for value education; basic Human Aspirations- Continuous Happiness and
Prosperity
Unit 2
Understanding Harmony at various levels (in brief): Self (‘I’) and Body, Self and
Myself, Human Body
Unit 3
Understanding Harmony in the Family (relationship), Society to world, nature
Unit 4
Understanding Harmony in the Nature and Existence - Whole existence as
Coexistence,
Unit 5
Right Understanding concepts –morals, Values, Ethic (professional), Value of time,
Confidence, Spirituality, Respect, Peace
Various issues related to Education, Societies (gender inequalities, security for women-
crime-), Nature (Earth) (Environment issues- Global Warming, deforestation, over
population, ozone layers depletion, climate change, etc.) and Life.
TEXT BOOKS
1. R R Gaur, RSangal, GP Bagaria, Human Values and professional Ethics , Excel
Books, New Delhi 2013.
2. Charles E Harris, Michael S. Protchard and Michael J Rabins, “Engineering
Ethics – Concepts and Cases”, Wadsworth Thompson Learning, United States,
2000 (Indian Reprint now available)
3. John R Boatright, “Ethics and the Conduct of Business”, Pearson Education,
New Delhi, 2003
B.Tech. Mechanical Engineering
Semester III
FLUID MECHANICS LAB
Course Code: ME-351 L T P Cr
0 0 2 1
Review of Orthographic Projections (1 drawing sheet) Orthographic Projection of solids in First angle of
projection, missing lines views, interpretation of views
Part and Assembly Drawing (2 drawing sheet)
Assembly drawing of eccentric, lathe tail stock, air valve, screw jack, connecting rod, safety valve etc.
Specification of Materials (1 drawing sheet)
Engineering materials, representation, Code designation of steel, copper,
aluminium etc.
Limits, Tolerance and Fits (1 drawing sheet)
Limit system, Tolerances, Method of placing limit dimensions, Fits-types
Surface Roughness (1 drawing sheet)
Introduction, nomenclature, machining symbols, indication of surface roughness
Production Drawing (1drawing sheet)
Types, Examples of simple machine elements like helical gear, bevel gear, crank,
connecting rod, belt pulley, piston etc.
Computer Aided Drafting (2 drawings)
Introduction, input, output devices, introduction to software like AutoCAD, ProE, basic commands and
development of 2D and 3D drawings of simple parts
UNIT-I
Introduction:Classification of Fluid Machines & Devices, Application of momentum and momentum equation to
flow through hydraulic machinery, Euler’s fundamental equation.
Impact of jet:Introduction to hydrodynamic thrust of jet on a fixed and moving surface (flat & curve), Effect of
inclination of jet with the surface.
Hydraulic Turbines:Classification of turbines, Impulse turbines, Constructional details, Velocity triangles,
Power and efficiency calculations, Governing of Pelton wheel. (10 Hours)
UNIT-II
Reaction Turbines:Francis and Kaplan turbines, Constructional details, Velocity triangles, Power and
efficiency calculations, Degree of reaction, Draft tube, Cavitation in turbines, Principles of similarity, Unit and
specific speed, Performance characteristics, Selection of water
turbines. (8 Hours)
UNIT-III
Centrifugal Pumps:Classifications of centrifugal pumps, Vector diagram, Work done by impellor, Efficiencies of
centrifugal pumps, Specific speed, Model testing, Cavitation & separation and their
control, Performance characteristics. (8 Hours)
UNIT-IV
Positive Displacement Pumps: Reciprocating pump theory, Slip and coefficient of discharges, Indicator diagram,
Effect and acceleration, Work saved by fitting air vessels, Comparison of centrifugal and reciprocating
pumps, Positive rotary pumps, Gear and Vane pumps, Performance characteristics.
(8 Hours)
UNIT-V
Other Machines: Hydraulic accumulator, Special duty pumps, Intensifier, Hydraulic press, Lift and cranes, Theory
of hydraulic coupling and torque converters, Performance characteristics.
Water Lifting Devices :Hydraulic ram, Jet pumps, Air lift pumps. (8 Hours)
BOOKS:
Hydraulic Machines by Jagdish Lal, Metropolitan book co. pvt ltd. Hydraulic
Machines: Theory & Design, V.P.Vasandhani, Khanna Pub.
Applied Hydraulics by Addison
Hydraulic Machines by R K Rajput, S.Chand & co Ltd.
B.Tech. Mechanical Engineering
Semester IV
I.C.ENGINE AND GAS TURBINES
Course Code: ME-402 L T P Cr
3 1 0 3.5
UNIT 1
Heat engines; Internal and external combustion engines; Classification of I.C. Engines; Cycle of operations in four
strokes and two-stroke IC engines; Wankle Engine.
Assumptions made in air standard cycles; Otto cycle; Diesel cycle; Dual combustion cycle; Comparison of Otto, diesel
and dual combustion cycles; Sterling and Ericsson cycles; Air standard efficiency, Specific work output. Specific
weight; Work ratio; Mean effective pressure; Deviation of actual engine cycle from ideal cycle.
(8 Hours)
UNIT II
Mixture requirements for various operating conditions in S.I. Engines; Elementary carburetor, Calculation of fuel air
ratio; The complete carburetor; Requirements of a diesel injection system; Type of injection system; Petrol injection;
Requirements of ignition system; Types of ignition systems, ignition timing; Spark plugs.
S.I. engines; Ignition limits; Stages of combustion in S. I. Engines; Ignition lag; Velocity of flame propagation;
Detonation; Effects of engine variables on detonation; Theories of detonation; Octane rating of fuels; Pre-ignition; S.I.
engine combustion chambers. Stages of combustion in C.I. Engines; Delay period; Variables affecting delay period;
Knock in C.I. Engines; Cetane rating; C.I. Engine combustion chambers.
(10 Hours)
UNIT III
Functions of a lubricating system, Types of lubrication system; Mist, Wet sump and dry sump systems; Properties of
lubricating oil; SAE rating of lubricants; Engine performance and lubrication; Necessity of engine cooling;
Disadvantages of overcooling; Cooling systems; Air-cooling, Water-cooling; Radiators.
Performance parameters; BHP, IHP, Mechanical efficiency; Brake mean effective pressure and indicative mean
effective pressure, Torque, Volumetric efficiency; Specific fuel consumption (BSFG, ISFC); Thermal efficiency; Heat
balance; Basic engine measurements; Fuel and air consumption, Brake power, Indicated power and friction power, Heat
lost to coolant and exhaust gases; Performance curves;
(8 Hours)
UNIT IV
Pollutants from S.I. and C.I. Engines; Methods of emission control, Alternative fuels for I.C. Engines; The current
scenario on the pollution front.
Working of a single stage reciprocating air compressor; Calculation of work input; Volumetric efficiency; Isothermal
efficiency; Advantages of multi stage compression; Two stage compressor with inter-cooling; Perfect inter cooling;
Optimum intercooler pressure; Rotary air compressors and their applications; Isentropic efficiency.
(8 Hours)
UNIT V
Brayton cycle; Components of a gas turbine plant; Open and closed types of gas turbine plants; Optimum pressure ratio;
Improvements of the basic gas turbine cycle; Multi stage compression with inter-cooling; Multi stage expansion with
reheating between stages; Exhaust gas heat exchanger; Application of gas turbines.
(8 Hours)
Recommended books
Internal combustion engine by Ramalingam scitech publication
Internal combustion engine by Ganeshan TMG
Internal combustion engine by Mathur & Sharma
B.Tech. Mechanical Engineering
Semester IV
ENGINEERING THERMODYNAMICS-II
Course Code: ME-403 L T P Cr
3 1 0 3.5
UNIT I
Introduction; classification of boilers; comparison of fire tube and water tube boiler; their advantages; description
of boiler; Lancashire; locomotive; Babcock; Wilcox etc.; boiler mountings; stop valve; safety valve; blow off
valve; feed check etc.; water level indicator; fusible plug; pressure gauge; boiler accessories; feed pump; feed
water heater; preheater; superheater; economizer; natural draught chimney design; artificial draught; stream jet
draught; mechanical draught; calculation of boiler efficiency and equivalent evaporation(no numerical problem)
(10 Hours)
UNIT II
Carnot cycle; simple and modified Rankine cycle; effect of operating parameters on rankine cycle performance;
effect of superheating; effect of maximum pressure; effect of exhaust pressure; reheating and regenerative
Rankine cycle; types of feed water heater; reheat factor; binary vapour cycle.
Simple steam engine, compound engine; function of various components. (8 Hours)
UNIT III
Function of steam nozzle; shape of nozzle for subsonics and supersonics flow of stream; variation of velocity;
area of specific volume; steady state energy equation; continuity equation; nozzle efficiency; critical pressure ratio
for maximum discharge; physical explanation of critical pressure; super saturated flow of steam; design of steam
nozzle. (8 Hours)
UNIT IV
Advantage of steam condensation; component of steam condensing plant; types of condensers; air leakage in
condensers; Dalton’s law of partial pressure; vacuum efficiency; calculation of cooling water requirement; air
expansion pump. (8 Hours)
UNIT V
Introduction; classification of steam turbine; impulse turbine; working principal; compounding of impulse
turbine; velocity diagram; calculation of power output and efficiency; maximum efficiency of a single stage
impulse turbine; design of impulse turbine blade section; impulse reaction turbine; working principle; degree of
reaction; parsons turbine; velocity diagram; calculation of power output; efficiency of blade height; condition of
maximum efficiency; internal losses in steam turbine; governing of steam turbine.
(8 Hours)
Text Books:
1. Thermal Engineering – P L Ballaney, Khanna Publishers
2. Thermodynamics and Heat Engines vol II – R Yadav, Central Publishing House
Reference Books :
1. Applied Thermodynamics for Engineering Technologists – T D Eastop and A McConkey, Pearson Education
2. Heat Engineering – V P Vasandani and D S Kumar, Metropolitan Book Co Pvt Ltd
B.Tech. Mechanical Engineering
Semester IV
MANUFACTURING SCIENCE-I
Course Code: ME-404 L T P Cr
4 0 0 4
Unit-I
Introduction :Importance of manufacturing. Economic & technological considerations in
manufacturing. Classification of manufacturing processes. Materials & manufacturing processes for
common items.
Metal Forming Processes :Elastic & plastic deformation, yield criteria. Hot working vs cold working.
Analysis (equilibrium equation method) of Forging process for load estimation with sliding friction
sticking friction and mixed condition for slab and disc. Work required for forging, Hand, Power, Drop
Forging (8 Hours)
Unit-II
Metal Forming Processes (continued): Analysis of Wire/strip drawing and maximum-reduction, Tube
drawing, Extrusionand its application. Condition for Rolling force and power in rolling. Rolling mills &
rolled-sections.Design, lubrication and defects in metal forming processes. (8 Hours)
Unit-III
Sheet Metal working :Presses and their classification, Die & punch assembly and press work methods and
processes. Cutting/Punching mechanism, Blanking vs Piercing. Compound vs Progressive die. Flat-face vs
Inclined-face punch and Load(capacity) needed. Analysis of forming process like cup/deep drawing. Bending &
spring-back. (8 Hours)
Unit-IV
Unconventional Metal forming processes :Unconventional metal forming processes such as explosive
forming, electro- magnetic, electro-hydraulic forming.
Powder Metallurgy :Powder metallurgy manufacturing process. The need, process, advantage and
applications.
Jigs & Fixtures :Locating & Clamping devices & principles. Jigs and Fixtures and its applications.
Manufacturing of Plastic components :Review of plastics, and its past, present & future uses. Injection
moulding. Extrusion of plastic section. Welding of plastics. Future of plastic & its applications. Resins &
Adhesives. (8 Hours)
Unit-V
Casting (Foundry) Basic principle & survey of casting processes. Types of patterns and allowances. Types and
properties of moulding sand. Elements of mould and design considerations, Gating, Riser, Runnes, Core.
Solidification of casting,. Sand casting, defects & remediesand inspection. Cupola furnace. Die Casting,
Centrifugal casting. Investment casting,CO2 casting and Stir casting etc. (8 Hours)
Books :
1. Manufacturing Science by Ghosh and Mallik
2. Production Engg. Science by P.C. Pandey
3. Production Technology by R.K. Jain
4. Manufacturing Technology by P.N. Rao., TMH
5. Materials and Manufacturing by Paul Degarmo.
6. Manufacturing Science by KM Moeed.
7. Manufacturing Engineering & Technology by Kalpakjian, Pearson Pub.
B.Tech. Mechanical Engineering
Semester IV
MEASUREMENT AND METROLOGY
Unit-I
Mechanical MeasurementsIntroduction: Introduction to measurement and measuring
instruments, Generalized measuring system and functional elements, units of measurement, static and
dynamic performance characteristics of measurement devices, calibration, concept of error, sources of
error, statistical analysis of errors.
Sensors and Transducers: Types of sensors, types of transducers and their characteristics.
Signal transmission and processing: Devices and systems.Signal Display & Recording Devices
(8 Hours)
Unit-II
Time related measurements: Counters, stroboscope, frequency measurement by direct comparison
.Measurement of displacement
Measurement of pressure: Gravitational, directing acting, elastic and indirect type pressure
transducers. Measurement of very low pressures
Strain measurement: Types of strain gauges and their working, strain gauge circuits, temperature
compensation. Strain rosettes, calibration. (8 Hours)
Unit-III:
Measurements of force and torque: Different types of load cells, elastic transducers, pneumatic &
hydraulic systems.
Temperature measurement: Thermometers, bimetallic thermocouples, thermistors and pyrometers.
Vibration: Seismic instruments, vibration pick ups and decibel meters, vibrometers
accelerometers. (8 Hours)
Unit-IV
Metrology and Inspection: Standards of linear measurement, line and end standards. Limit fits and
tolerances. Interchangeability and standardization, Linear and angular measurements devices and systems
Comparators: Sigma, Johansson’s Microkrator.Limit gauges classification, Taylor’s Principle of Gauge
Design. (8 Hours)
Unit-V
Measurement of geometric forms like straightness, flatness, roundness, Tool maker’s microscope, profile
project autocollimator. Interferometry: principle and use of Interferometry, optical flat.
Measurement of screw threads and gears, Surface texture: quantitative evaluation of surface roughness and
its measurement.
Measurement and Inspection: Dimensional inspection – Tolerance, Limit gauging, comparators,
Surface roughness, Feature inspection. (8 Hours)
References
1. Beckwith Thomas G., Mechanical Measurements, Narosa Publishing House, N. Delhi.
2. Doeblein E.O., “Measurement Systems, Application Design”, McGraw Hill, 1990.
3. Kumar D.S., “Mechanical Measurements and Control”, Metropolitan, N. Delhi.
4. Hume K.J., “Engineering Metrology”, MacDonald and Co. 1963
5. Gupta, I.C., “Engineering Metrology”, Dhanpat Rai & Sons, New Delhi, 1994
6. Sirohi, “Mechanical Measurement” New Age Publishers
7. Jain, R.K., “Engineering Metrology” Khanna Publishers
8. Jain, R.K., “Mechanical Measurement” Khanna Publishers
B.Tech. Mechanical Engineering
Semester IV
Strength of Materials-II
Course Code: ME-406
L T P Cr
3 1 0 3.5
Unit –I
Strain energy: Introduction to strain energy, energy of dilation and distortion. Resilience, stress
due to suddenly applied loads. Castigliano’s and Maxwell’s theorem of reciprocal deflection.
Theories of failure: Maximum principal stress theory, maximum shear stress theory, maximum
principal strain theory, total strain energy theory, shear strain energy theory. Graphical
representation and derivation of equation for these theories and their application to problems
related to two dimensional stress systems.(Hours 10)
Unit –II
Torsion: Derivation of torsion equation and its assumptions and its application to the hollow and
solid circular shafts. Torsional rigidity, combined torsion and bending of circular shafts; principal
stress and maximum shear stresses under combined loading of bending and torsion.
(Hours 6)
Unit –III
Springs: Open and closed coiled helical springs under the action of axial load and/or couple. Flat
spiral springs- derivation of formula for strain energy, maximum stress and rotation. Leaf spring
deflection and bending stresses.
(Hours 6)
Unit – IV
Thin cylinders and spheres: Calculation of Hoop stress, longitudinal stress in a cylinder, effects
of joints, change in diameter, length and internal volume. Principal stresses in sphere, change in
diameter and internal volume.
Thick cylinders: Derivation of Lame’s equations, calculation of radial, longitudinal and hoop
stresses and strains due to internal pressure in thick cylinders, compound cylinders, hub shrunk on
solid shafts, shrinkage allowance and shrinkage stress.
(Hours 10)
Unit –V
Unsymmetrical Bending: Properties of beam cross-section, slope of neutral axis, stress and
deflection
in unsymmetrical bending, determination of shear center and flexural axis(for symmetry about
both axis and about one axis) for I-section and channel- section
Bending of curved beams: Calculation of stresses in cranes or chain hooks, rings of circular and
trapezoidal section, and chain links with straight sides.
Rotational discs: Stresses in rotating discs and rims of uniform thickness; disc of uniform
strength
(Hours 10)
Suggested Readings / Books:
LIST OF EXPERIMENTS
1. To make a trial on single cylinder 4-stroke Diesel Engine to calculate B. H. P., S.F.C. and to draw its
characteristics curves.
2. To make a trial on 4-stroke high-speed diesel engine and to draw its Heat Balance Sheet.
3. and to draw its characteristic Curves.
4. To make Morse Test to calculate IHP of the multi cylinder petrol engine and to determine its
mechanical To make a trial on Wiley’s jeep Engine at constant speed to calculate B. H. P., S. F. C.
Thermal efficiency.
5. To calculate the isothermal efficiency and volumetric efficiency of a 2 stage reciprocating air
compressor.
6. To find out the efficiency of an air Blower.
7. To make a trial on the Boiler to calculate equivalent evaporation and efficiency of the Boiler.
8. To study the following models;
a. Gas Turbine.
b. Wankle Engine.
9. To study
a. Lubrication and cooling systems employed in various I. C. Engines in the Lab
b. Braking system of automobile in the lab
10. To study a Carburetor.
11. To study
(a) the Fuel Injection System of a C. I. Engine.
(b) Battery Ignition system of a S. I. Engine
12. To study Cooling Tower.
13. To study multi Cylinder four strokes vertical Diesel Engine test RIG With Hydraulic Dynamometer
B.Tech. Mechanical Engineering
Semester IV
ENGINEERING THERMODYNAMICS LAB
Course Code: ME-453 L T P Cr
0 0 2 1
UNIT I
Introduction: Definition, Design requirements of machine elements, Design procedure, Standards in
design, Selection of preferred sizes, Indian Standards designation of carbon & alloy steels, Selection of
materials for static and fatigue loads
Design against Static Load: Modes of failure, Factor of safety, Principal stresses, Stresses due to
bending and torsion, Theory of failure (8 Hours)
UNIT II
Design against Fluctuating Loads: Cyclic stresses, Fatigue and endurance limit, Stress
concentration factor, Stress concentration factor for various machine parts, Notch sensitivity, Design
for finite and infinite life, Soderberg, Goodman & Gerber criteria
Riveted Joints-Riveting methods, materials, Types of rivet heads, Types of riveted joints,
Caulking and Fullering, Failure of riveted joint, Efficiency of riveted joint, Design of boiler joints,
Eccentric loaded riveted joint (8 Hours)
UNIT III
Shafts: Cause of failure in shafts, Materials for shaft, Stresses in shafts, Design of shafts subjected
to twisting moment, bending moment and combined twisting and bending moments, Shafts subjected
to fatigue loads, Design for rigidity
Keys and Couplings: Types of keys, splines, Selection of square & flat keys, Strength of sunk key,
Couplings- Design of rigid and flexible couplings (8 Hours)
UNIT IV
Mechanical Springs: Types, Material for helical springs, End connections for compression and tension
helical springs, Stresses and deflection of helical springs of circular wire, Design of helical springs
subjected to static and fatigue loading (8 Hours)
UNIT V
Power Screws: Forms of threads, multiple threads, Efficiency of square threads, Trapezoidal threads,
Stresses in screws, Design of screw jack (6 Hours)
UNIT I
Introduction Links-types, Kinematics pairs-classification, Constraints-types, Degrees of freedom of
planar mechanism, Grubler’s equation, linkage mechanisms, inversions of four bar chain, slider crank
chain and double slider crank chain
Velocity in Mechanisms Velocity of point in mechanism, relative velocity method, Velocities in
four bar mechanism, slider crank mechanism and quick return motion mechanism, Rubbing velocity
at a pin joint, Instantaneous center method, Types & location of instantaneous centers, Kennedy’s
theorem, Velocities in four bar mechanism & slider crank mechanism (10 Hours)
UNIT II
Acceleration in Mechanisms Acceleration of a point on a link, Acceleration diagram, Coriolis
component of acceleration, Crank and slotted lever mechanism, Klein’s construction for Slider Crank
mechanism and Four Bar mechanism, Analytical method for slider crank mechanism
Mechanisms with Lower Pairs Pantograph, Exact straight line motion mechanisms-Peaucellier’s,
Hart and Scott Russell mechanisms, Approximate straight line motion mechanisms–Grass-Hopper,
Watt and Tchebicheff mechanisms, Analysis of Hooke’s joint, Davis and Ackermann
steering gear mechanisms. (8 Hours)
UNIT III
FRICTION Laws of friction, Friction on inclined plane, Efficiency on inclined plane, Friction in
journal bearing-friction circle, Pivots and collar friction-uniform pressure and uniform wear, Belt
and pulley drive, Length of open and cross belt drive, Ratio of driving tensions for flat
belt drive, centrifugal tension, condition for maximum power transmission, V belt drive
Brakes & Dynamometers Shoe brake, Band brake, Band and Block brake, Absorption and
transmission type dynamometers (8 Hours)
UNIT IV
CAMS Cams and Followers - Classification & terminology, Cam profile by graphical methods
with knife edge and radial roller follower for uniform velocity, simple harmonic and
parabolic motion of followers, Analytical methods of cam design – tangent cam with
roller follower and circular cams with flat faced follower (8 Hours)
UNIT V
Gears & Gear Trains Classification & terminology, law of gearing, tooth forms & comparisons,
Systems of gear teeth, Length of path of contact, contact ratio, interference & under cutting in
involute gear teeth, minimum number of teeth on gear and pinion to avoid interference, simple,
compound, reverted and planetary gear trains, Sun and planet gear. (8 Hours)
Unit-III
Grinding & Super finishing Grinding : Grinding wheels, abrasive & bonds, cutting action. Grinding
wheel specification. Grinding wheel wear - attritions wear, fracture wear. Dressing and Truing. Max
chip thickness and Guest criteria. Surface and Cylindrical grinding. Centerless grinding. Super finishing
: Honing, lapping, polishing.
Standardization & Interchangeability, Limits, Fits & Tolerance and Surface- roughness:
Introduction to Standardization & Interchangeability Limits, Fits, Tolerances and IS standards, Limit-
gauges, and surface-roughness. (8 Hours)
Unit-IV
Metal Joining (Welding)Survey of welding and allied processes. Gas welding and cutting, process
and equipment. Arc welding : Power sources and consumables. TIG & MIG processes and their
parameters. Resistance welding - spot, seam projection etc. Other welding processes such as
atomic hydrogen, submerged arc, electroslag, friction welding.Soldering & Brazing.Thermodynamic
and Metallurgical aspects in welding and weld,. Shrinkage/residual stress in welds. Distortions &
Defects in welds and remedies.Weld decay in HAZ. (8 Hours)
Unit-V
Introduction to Un-conventional Machining and Welding Need & benefits, application and working
principle of EDM, ECM, LBM, EBM, USM. AJM, WJM. Similarly, non-conventional welding
applications such as LBW, USW, EBW, Plasma-arc welding, Diffusion welding, Explosive
welding/cladding. (8 Hours)
Books
1. Manufacturing science by Ghosh and Mallik
2. Fundamentals of Metal Cutting and Machine tools by Boothroyd
3. Production Technology by R.K. Jain
4. Production Technology - H.M.T.
5. Production Engineering Science by P.C. Pandey
6. Modern Machining Processes by P.C. Pandey & H.S. Shan
7. Manufacturing science by Degarmo
8. Fundamentals of metal cutting & machine tools - Juneja & Shekhon
9. Process & materials of manufacturing - Lindburg.
10. Advanced Machining Process - VK Jain
B.Tech. Mechanical Engineering
Semester V
HEAT AND MASS TRANSFER
Course Code: ME-504 L T P Cr
3 1 0 3.5
UNIT-I
Introduction to Heat Transfer: Concepts of the mechanisms of heat flows; Conduction,
convection and radiation; Effect of temperature on thermal conductivity of materials; Introduction
to combined heat transfer mechanism.
Conduction: One-dimensional general differential heat conduction equation in the rectangular,
cylindrical and spherical coordinate systems; Initial and boundary conditions.
Steady State one-dimensional Heat conduction : Composite Systems in rectangular, cylindrical and
spherical coordinates with and without energy generation; Thermal resistance concept; Analogy
between heat and electricity flow; Thermal contact resistance; Critical thickness of insulation.
(10 Hours)
UNIT-II
Fins: Heat transfer from extended surfaces, Fins of uniform cross-sectional area; Errors of
measurement of temperature in thermometer wells.
Transient Conduction: Transient heat conduction; Lumped capacitance method; Time
constant; Unsteady state heat conduction in one dimension only, Heisler charts. (8 Hours)
UNIT-III
Forced Convection: Basic concepts; Hydrodynamic boundary layer; Thermal boundary layer;
Approximate integral boundary layer analysis; Analogy between momentum and heat transfer in
turbulent flow over a flat surface; Mixed boundary layer; Flow over a flat plate; Flow across a
single cylinder and a sphere; Flow inside ducts; Empirical heat transfer relations; Relation between
fluid friction and heat transfer; Liquid metal heat transfer.
Natural Convection : Physical mechanism of natural convection; Buoyant force; Empirical heat
transfer relations for natural convection over vertical planes and cylinders, horizontal plates and
cylinders, and sphere ; Combined free and forced convection. (8 Hours)
UNIT-IV
Thermal Radiation : Basic radiation concepts; Radiation properties of surfaces; Black body radiation
Planck’s law, Wein’s displacement law, Stefan Boltzmann law, Kirchoff’s law; ; Gray body; Shape
factor; Black-body radiation; Radiation exchange between diffuse non black bodies in an enclosure;
Radiation shields; Radiation combined with conduction and convection; Absorption and emission in
gaseous medium; Solar radiation; Green house effect. (8 Hours)
UNIT-V
Heat Exchanger : Types of heat exchangers; Fouling factors; Overall heat transfer coefficient;
Logarithmic mean temperature difference (LMTD) method; Effectiveness-NTU method; Compact
heat exchangers.
Condensation And Boiling : Introduction to condensation phenomena; Heat transfer relations for
laminar film condensation on vertical surfaces and on outside & inside of a horizontal tube; Effect of
non-condensable gases; Dropwise condensation; Heat pipes; Boiling modes, pool boiling;
Hysteresis in boiling curve; Forced convective boiling.
Introduction To Mass Transfer : Introduction; Fick's law of diffusion; Steady state equimolar
counter diffusion; Steady state diffusion though a stagnant gas film. (8 Hours)
Books:
1. Elements of Heat transfer by Bayazitouglu & Ozisik, McGraw-Hill Book Company.
2. Heat Transfer By J.P. Holman, McGraw-Hill International edition.
3. Schaum's outline of Heat Transfer by Pitts & Sisson McGraw-Hill International edition.
4. Principles of Heat Transfer by Frank Kreith, McGraw-Hill Book co.
5. Fundamentals of Momentum, Heat and Mass Transfer by James R.Welty;
John Wiley & Sons (Pvt). Ltd.
6. Heat Transfer, by Vijay Gupta, New Age International (P) Ltd. Publishers
(EWP)B.Tech. Mechanical Engineering
Semester V
PRODUCTION PLANNING & CONTROL
Course Code: ME-505 L T P Cr
3 0 0 3
Unit-I
Introduction: Types and characteristics of production systems Objective and functions of
Production, Planning & Control, Place of production, Planning in Engineering, manufactures
organization.
Preplanning: Forecasting & Market Analysis. Factory Location & Layout, Equipment policy and
replacement. Preplanning production, capacity planning. (8 Hours)
Unit-II
Production Planning: Aggregate Planning, MPS, Material Resource Planning, Selection of
material methods, machines & manpower. Routing, Scheduling and Dispatching and its sheets &
charts, Production Line Balancing. (8 Hours)
Unit-III
Production and Inventory Control: Progress control through records and charts. Types
of inventories, Inventory Classification. Inventory Control under constraints Economic lot
(batch) size. Trends in purchasing and store keeping, JIT production MRP II, comparison of Push
& Pull systems, ERP, CAPPC. (8 Hours)
Unit-IV
Productivity: Importance, Productivity patterns, productivity measurements & ratios,
improvement-maintenance process.
Human Factors & Ergonomics: Human abilities, Training & motivation safety programs,
workplace design & working conditions. (8 Hours)
Books :
Note: Eight experiments out of the following are to be performed. Students are
advised to use design data book for the design. Drawing shall be made wherever
necessary on small drawing sheets
1. Shear-angle determination (using formula) with tube cutting (for orthogonal) on lathe machine.
2. Bolt (thread) making on Lathe machine
3. Tool grinding (to provide tool angles) on tool-grinder machine.
4. Gear cutting on Milling machine.
5. Machining a block on shaper machine.
6. Finishing of a surface on surface-grinding machine.
7. Drilling holes on drilling machine and study of twist-drill.
8. Study of different types of tools and its angles & materials.
9. Experiment on tool wear and tool life.
10. Experiment on jigs/Fixtures and its uses
11. Gas welding experiment
12. Arc welding experiment
13. Resistance welding experiment.
14. Soldering & Brazing experiment
15. Experiment on unconventional machining.
16. Experiment on unconventional welding.
17. Experiment on TIG/MIG Welding.
18. Macro and Microstructure of welding joints, HAZ.
B.Tech. Mechanical Engineering
Semester V
HEAT & MASS TRANSFER – LAB
Course Code: ME-553 L T P Cr
0 0 2 1
UNIT II
Principles of organization, Importance and characteristics of organization, Organization theories;
Classical Organization theory; Neo-Classical organization theory, Modern organization theory; Types of
organization, Military or line organization, Functional organization, Line and staff organization,
Committees. (8 Hours)
UNIT III
Objectives of PPC; Functions of PPC; Preplanning and planning; Routing; Estimating; scheduling-master
schedule; Daily schedule; Gantt chart; Dispatching –centralized vs. decentralized; Control; Follow up and
progress reporting.
Introduction; Product development; Product characteristics; Role of product development; 3Ss –
Standardization; Simplification and Specialization. (8 Hours)
UNIT IV
Introduction, Objectives and importance of sales forecasting, Types of forecasting, Methods of sales
forecasting-Collective opinion method, Delphi technique, economic indicator method; Regression
analysis, Moving average method, Time series analysis.
Introduction, Functions of inventory; Types of inventory; Control importance and functions, Inventory
costs, Factors affecting inventory control, Various inventory control models. A. B. C. analysis, Lead-time
calculations. (8 Hours)
UNIT V
Introduction; Objectives; Concept and life cycle of a product and V.E.; Steps in VE., Methodology and
techniques, Fast diagram, Matrix method.
Various concepts in industrial engineering
a) WAGES AND INCENTIVES; -Concept; Types; Plans; Desirable characteristics.
b) ERGONOMICS; - its importance; Man-machine work place system; Human factors considerations in
system design.
c) SUPPLY CHAIN MANAGEMENT; - its definition, Concept, Objectives, Applications, benefits,
Some successful cases in Indian Industries.
d) JIT; - Its definition, Concept, Importance, Misconception, Relevance, Applications, Elements of JIT
(brief description).
e) MRP;-Introduction, Objectives, factors, Guide lines, Techniques Elements of MRP system, Mechanics
of MRP, MRP-II
f) TIME MANAGEMENT;-Introduction, Steps of time management, Ways for saving time, Key for
time saves. (8 Hours)
Reference and Text books:
Production planning and control by S.Elion
Modren production Management by S.S Buffa
Industrial engg. and management manufacturing system by Surender kumar,
Satya prakashan
Essence of Supply Chain Management by R.P mohanty and S.G Deshmukh
Industrial engg. and management by S Sharma and Savita sharama
B.Tech. Mechanical Engineering
Semester VI
UNCONVENTIONAL MANUFACTURING PROCESSES
Course Code: ME-602 L T P Cr
3 0 0 3
UNIT I
Introduction: Limitations of conventional manufacturing processes need of unconventional
manufacturing proc
processes & its class
classificat
ification and its fut
future possibi
possibilit
lities.
ies. (8 Hours)
Unit-II
Unconventional Machining Process: Principle and working and applications of unconventional
machining process such as Electro-Disc
Electro-Discharge machining, Ele
Electro- chem
chemical machining, ultrasonic
machining, Abr
Abrasiv
asive jet machining etc. (8 Hours)
Unit-III
Unconventional Machining Process(continued) :Principle
Principle and working and application of
unconv
unconventional machining proc
process
esses such as Laser beam machachining, Electron
Electron beam machining,
Ultrasonic machini
achining etc. (these can also be used for welding). (8 Hours)
Unit-IV
Unconventional weld elding processes: Explosiv
plosive welding, Cladding etc. Und
Under water welding,
Metalizing, Plasma are welding/c
welding/cutting etc. (8 Hours)
Unit-V
Unconventional Forming process
processes: Princi
Principle, workin
working and appl
applications of High energy
form
forming processe
processes such as Explosiv
plosive Form
Forming, Electrom
lectromagnetic form
forming, Electro-
Discharge form
orming, wat
water ham
hammer form
orming, explosiv
osive com
compac
paction etc.
Electronic-device Manufacturing: Brief descrip
description of Diffus
Diffusion and Photo- Lithogra
Lithography process for
electronic-d
ectronic-device manufacturing. (8 Hours)
Books
1. Modern Machining Proce
Processes – P.C. Pandey
2. Unconv
Unconventiona
entional Machini
achining – V.K. Jain
B.Tech. Mechanical Engineering
Semester VI
MECHANICAL VIBRATION
UNIT - II
Single Degree Freedom: Forced Vibration
Forced vibration, Harmonic excitation with viscous damping, steady state vibrations, Forced
vibrations with rotating and reciprocating unbalance, Support excitation, Vibration isolation,
Transmissibility, Vibration measuring instruments, Displacement, velocity and acceleration measuring
instruments (8 Hours)
UNIT- III
Two Degree Freedom systems Introduction, Principal modes, Double pendulum, Torsional system
with damping, coupled system, undamped dynamic vibration absorbers, Centrifugal pendulum
absorbers, Dry friction damper (8 Hours)
UNIT- IV
Multi Degree Freedom system: Exact Analysis
Undamped free and forced vibrations of multi-degree freedom systems, influence number,
Reciprocal theorem, Torsional vibration of multi-degree rotor system, Vibration of gear system,
Principal coordinates, Continuous systems- Longitudinal vibrations of bars, Torsional vibrations of
circular shafts (8 Hours)
UNIT- V
Multi Degree Freedom system: Numerical Analysis Rayleigh’s, Dunkerely’s, Holzer’s ad Stodola
methods, Rayleigh-Ritz method
CRITICAL SPEED OF SHAFTS Shaft with one disc with and without damping, Multi-disc
shafts, Secondary critical speed. (8 Hours)
UNIT I
Spur Gears Tooth forms, System of gear teeth, contact ratio, Standard proportions of gear systems,
Interference in involute gears, Backlash, Selection of gear materials, Gear manufacturing methods,
Design considerations, Beam strength of gear tooth, Dynamic tooth load, Wear strength of gear
tooth, Failure of gear tooth, Design of spur gears, AGMA and Indian standards. (8 Hours)
UNIT II
Helical Gears Terminology, Proportions for helical gears, Beam strength and wear strength of helical
gears, herringbone gears, crossed helical gears, Design of helical gears.
Worm Gears Types of worms, Terminology, Gear tooth proportions, Efficiency of worm gears,
Heat dissipation in worm gearing, Strength and wear tooth load for worm gears, Design of worm
gearing (8 Hours)
UNIT III
Sliding Contact Bearing Types, Selection of bearing, Plain journal bearing, Hydrodynamic
lubrication, Properties and materials, Lubricants and lubrication, Hydrodynamic journal
bearing, Heat generation, Design of journal bearing, Thrust bearing-pivot and collar
bearing, Hydrodynamic thrust bearing,
Rolling Contact Bearing Advantages and disadvantages, Types of ball bearing, Thrust ball bearing,
Types of roller bearing, Selection of radial ball bearing, Bearing life, Selection of roller bearings,
Dynamic equivalent load for roller contact bearing under constant and variable loading, Reliability of
Bearing, Selection of rolling contact bearing, Lubrication of ball and roller bearing, Mounting of
bearing (10 Hours)
UNIT IV
Design of flat belts &Pulleys, Design /selection of V belts &Pulleys, Design/selection of wire ropes,
Design/selection of chains Single &multiple Plate clutch, Cone clutch External shoe brake, Internal shoe
brakes (8 Hours)
UNIT V
IC ENGINE PARTS Selection of type of IC engine, General design considerations, Design of
Cylinder and cylinder head; Design of piston, piston ring and gudgeon pin; Design of connecting rod;
Design of centre crankshaft (8 Hours)
Note: Design data book is allowed in the examination
Books and References:
1. Mechanical Engineering Design – Joseph E. Shigely, McGraw Hill Publications
2. Design of Machine Memebers-Alex Valance and VI Doughtie, McGraw Hill Co.
3. Machine design-M.F. Spott, Prentice Hall India
4. Machine design -Black & Adams, Mc Graw Hill
5. Design of Machine Elements-V.B. Bhandari, Tata McGraw Hill Co.
B.Tech. Mechanical Engineering
Semester VI
THEORY OF MACHINES II
Course Code: ME-605 L T P Cr
3 1 0 3.5
UNIT I
Static & Dynamic Force Analysis Static equilibrium of two/three force members, Static equilibrium
of member with two forces and torque, Static force analysis of linkages, D’Alembert’s principle,
Equivalent offset inertia force, Dynamic force analysis of four link mechanism and slider crank
mechanism, Engine force analysis-Piston and crank effort (8 Hours)
UNIT II
Turning Moment & Flywheel Turning moment on crankshaft, Turning moment diagrams-single
cylinder double acting steam engine, four stroke IC engine and multi-cylinder steam engine,
Fluctuation of energy, Flywheel (8 Hours)
UNIT III
Balancing of Machines Static and dynamic balancing, Balancing of several masses in the same
plane and different planes, Balancing of reciprocating masses, Balancing of primary force in
reciprocating engine, Partial balancing of two cylinder locomotives, Variation of tractive force,
swaying couple, hammer blow (8 Hours)
UNIT IV
Governors Terminology, Centrifugal governors-Watt governor, Dead weight governors-Porter &
Proell governor, Spring controlled governor-Hartnell governor, Sensitivity, Stability, Hunting,
Isochronism, Effort and Power of governor, Controlling force diagrams for Porter governor and
Spring controlled governors (8 Hours)
UNIT V
Gyroscopic Motion Principles, Gyroscopic torque, Effect of gyroscopic couple on the stability of aero
planes & automobiles
Mechanical Vibrations Types of vibrations, Degrees of freedom, Single degree free & damped
vibrations, Forced vibration of single degree system under harmonic excitation, Critical speeds of
shaft (8 Hours)
Books and References:
1. Theory of Machines - Thomas Bevan
2. Theory of Machines and Mechanisms- Shigley
3. Theory of Machines and Mechanisms-Ghosh & Mallik
4. Theory of Machines and Mechanisms- Rao & Dukkipati
5. Theory of Machines - S.S. Rattan
6. Theory of Machines – R.K. Bansal
7. Mechanics of Machines – V. Ramamurti
8. Theory of Machines – Khurmi & Gupta
9. Theory of Machines – P.L. Ballaney
10. Theory of Machines – V. P. Singh
B.Tech. Mechanical Engineering
Semester VI
REFRIGERATION & AIR CONDITIONING
Course Code: ME-606 L T P Cr
3 1 0 3.5
Unit-I
Refrigeration: Introduction to refrigeration system, Methods of refrigeration, Carnot refrigeration
cycle, Unit of refrigeration, Refrigeration effect & C.O.P.
Air Refrigeration cycle: Open and closed air refrigeration cycles, Reversed Carnot cycle, Bell
Coleman or Reversed Joule air refrigeration cycle, Aircraft refrigeration system, Classification of
aircraft refrigeration system. Boot strap refrigeration, Regenerative, Reduced ambient, Dry air rated
temperature (DART). (8 Hours)
Unit-II
Vapour Compression System: Single stage system, Analysis of vapour compression cycle, Use of T-S
and P-H charts, Effect of change in suction and discharge pressures on C.O.P, Effect of sub cooling
of condensate & superheatingof refrigerant vapour on C.O.P of the cycle, Actual vapour
compression refrigeration cycle, Multistage vapour compression system requirement, Removal of
flash gas, Intercooling, Different configuration of multistage system, Cascade system. (8 Hours)
Unit-III
Vapour Absorption system; Working Principal of vapour absorption refrigeration system,
Comparison between absorption & compression systems, Elementary idea of refrigerant absorbent
mixtures, Temperature – concentration diagram & Enthalpy – concentration diagram , Adiabatic
mixing of two streams, Ammonia – Water vapour absorption system, Lithium- Bromide water vapour
absorption system, Comparison.
Refrigerants: Classification of refrigerants, Nomenclature, Desirable properties of refrigerants,
Common refrigerants, Secondary refrigerants and CFC free refrigerants. (8 Hours)
Unit-IV
Air Conditioning: Introduction to air conditioning, Psychometric properties and their definitions,
Psychometric chart, Different Psychometric processes, Thermal analysis of human body, Effective
temperature and comfort chart, Cooling and heating load calculations, Selection of inside &
outside design conditions, Heat transfer through walls & roofs, Infiltration & ventilation, Internal
heat gain, Sensible heat factor ( SHF ), By pass factor, Grand Sensible heat factor ( GSHF), Apparatus
dew point (ADP). (10 Hours)
Unit-V
Refrigeration Equipment & Application: Elementary knowledge of refrigeration & air
conditioning equipments e.g compressors, condensers, evaporators & expansion devices, Air
washers, Cooling, towers & humidifying efficiency, Food preservation, Cold storage, Refrigerates
Freezers, Ice plant, Water coolers, Elementary knowledge of transmission and distribution of air
through ducts and fans, Basic difference between comfort and industrial air conditioning. (8 Hours)
Books:
1. Refrigeration and Air conditioning, by Manohar Prasad, New Age International (P) Ltd.Pub.
2. Refrigeration and Air conditioning by C.P Arora.
3. Refrigeration and Air conditioning by Arora & Domkundwar.
4. Refrigeration and Air conditioning by stoecker & Jones.
5. Refrigeration and Air conditioning by Roy J. Dossat.
B.Tech. Mechanical Engineering
Semester VI
MACHINE DESIGN-II LAB
Course Code: ME-651 L T P Cr
0 0 3 1.5
Note: Eight experiments out of the following are to be performed. Students are
advised to use design datebook for the design. Drawing shall be made wherever
necessary on small drawing sheets
Unit-I
Power Unit and Gear Box: Principles of Design of main components. Valve mechanism. Power and
Torque characteristics. Rolling, air and gradient resistance. Tractive effort. Gear Box. Gear ratio
determination. Design of Gear box. (8 Hours)
Unit-II
Transmission System: Requirements. Clutches. Toque converters. Over Drive and free wheel, Universal
joint. Differential Gear Mechanism of Rear Axle. Automatic transmission, Steering and Front Axle.
Castor Angle, wheel camber & Toe-in, Toe-out etc.. Steering geometry. Ackerman mechanism,
Understeer and Oversteer. (8 Hours)
Unit-III
Braking System: General requirements, Road, tyre adhesion, weight transfer, Braking ratio.
Mechanical brakes, Hydraulic brakes. Vacuum and air brakes. Thermal aspects.
Chasis and Suspension System: Loads on the frame. Strength and stiffness. Various suspension systems.
(8 Hours)
Unit-IV
Electrical System : Types of starting motors, generator & regulators, lighting system, Ignition system,
Horn, Battery etc.
Fuel Supply System: Diesel & Petrol vehicle system such as Fuel Injection Pump, Injector & Fuel
Pump, Carburetor etc. MPFI. (8 Hours)
Unit-V
Automobile Air Conditioning: Requirements, Cooling & heating systems.
Cooling & Lubrication System: Different type of cooling system and lubrication system.
Maintenance system: Preventive maintenance, break down maintenance and over hauling. (8 Hours)
References-
1. Automotive Engineering- Hietner
2. Automobile Engineering - Kripal Singh.
3. Automobile Engineering - Narang.
4. Automotive Mechanics- Crouse
5. Automobile Engineering - Newton and Steeds.
B.Tech. Mechanical Engineering
Semester VII
TOTAL QUALITY MANAGEMENT (TQM)
Unit-I
Quality Concepts Evolution of Quality control, concept change, TQM Modern concept, Quality concept
in design, Review off design, Evolution of proto type.
Control on Purchased Product Procurement of various products, evaluation of supplies, capacity
verification, Development of sources, procurement procedure.
Manufacturing Quality Methods and Techniques for manufacture, Inspection and control of product,
Quality in sales and services, Guarantee, analysis of claims.
(8 Hours)
Unit-II
Quality Management Organization structure and design, Quality function, decentralization, Designing
and fitting organization for different types products and company, Economics of quality value and
contribution, Quality cost, optimizing quality cost, seduction programme.
Human Factor in Quality Attitude of top management, co-operation, of groups, operators attitude,
responsibility, causes of operators error and corrective methods.
(8 Hours)
Unit-III
Control Charts Theory of control charts, measurement range, construction and analysis of R charts,
process capability study, use of control charts.
Attributes of Control Charts Defects, construction and analysis off-chart, improvement by control
chart, variable sample size, construction and analysis of C-chart.
(8 Hours)
Unit-IV
Defects Diagnosis and Prevention Defect study, identification and analysis of defects, corrective
measure, factors affecting reliability, MTTF, calculation of reliability, Building reliability in the product,
evaluation of reliability, interpretation of test results, reliability control, maintainability, zero defects,
quality circle.
(8 Hours)
Unit-V
IS0-9000 and its concept of Quality Management: ISO 9000 series, Taguchi method, JIT in some
details
(8 Hours)
References:
1. Lt. Gen. H.LaI, "Total Quality management", Wiley Eastern Limited, 1990. .
2. Greg Bounds. “Beyond Total Quality Management”. McGraw Hill, 1994.
3. Menon, H.G, "TQM in New Product manufacturing", McGraw Hill 1992
B.Tech. Mechanical Engineering
Semester VIII
OPERATIONS RESEARCH
Unit I
Introduction: Basics of Operations Research
Linear Programming- Introduction & Scope, Problem formulation, Graphical Method, Simplex
methods, primal & dual problem sensitivity analysis.
(8 Hours)
Unit-II
Transportation & Assignment problems.
Deterministic Dynamic Programming- Multistage decision problems & solution, Principle of
optimality.
(8 Hours)
Unit-III
Decision theory- Decision under various conditions.
Game Theory- Two Person Zero sum game, Solution with / without Saddle point, Dominance Rule,
Different Methods like Algebraic, Graphical, Liner Programming
Sequencing- Basic assumption, n Jobs through two / three machines, 2 Jobs on m machines.
(8 Hours)
Unit-IV
Stochastic inventory models- Single & multi period models with continuous & discrete demands,
Service level & reorder policy
Simulations- Use, advantages& limitations, Monte-carlo simulation, Application to queuing,
inventory & other problems.
(8 Hours)
Unit-V
Queuing models- Characteristics of Queuing Model, M/M/1 & M/M/S system, cost consideration
Project Management: Basic concept, Rules for drawing the network diagram, Applications of CPM and
PERT techniques in Project planning and control; crashing of operations; resource allocation.
(8 Hours)
Text Books
Operations Research by : Wangner
Operations Research by : Taha
Introduction to Management Science by: Hiller & Hiller
Operations Research by : Wayne L. Winston1
B.Tech. Mechanical Engineering
Semester VIII
NON-CONVENTIONAL ENERGY RESOURCES
Course Code: ME-705 L T P Cr
4 0 0 4
UNIT-I
Energy resources and their utilization : Indian and global energy sources, Energy exploited,
Energy planning, Energy parameters (energy intensity, energy-GDP elasticity), Introduction to various
sources of energy, Solar thermal, Photovoltaic, Water power, Wind energy, Biomass, Ocean thermal,
Tidal and wave energy, Geothermal energy, Hydrogen energy systems, Fuel
cells, Decentralized and dispersed generation.
Solar radiations: Extra terrestrial radiation, Spectral distribution, Solar constant, Solar radiations on earth,
Measurement of solar radiations, Solar radiation geometry, Flux on a plane surface, Latitude,
Declination angle, Surface azimuth angle, Hour angle, Zenith angle, Solar
altitude angle expression for angle between incident beam and the normal to a plane
surface (no derivation), Local apparent time, Apparent motion of sun, Day length, Solar radiation data for
India.
(8 Hours)
UNIT-II
Solar energy: Solar thermal power and it's conversion, Solar collectors, Flat plate, Performance
analysis of flat plate collector, Solar concentrating collectors, Types of concentrating collectors,
Thermodynamic limits to concentration, Cylindrical collectors, Thermal analysis of solar collectors,
Tracking CPC and solar swing .Solar thermal energy storage, Different systems, Solar pond. Applications,
Water heating, Space heating & cooling, Solar distillation, solar pumping, solar cooking, Greenhouses,
Solar power plants.
Solar photovoltaic system: Photovoltaic effect, Efficiency of solar cells, Semiconductor materials for
solar cells, Solar photovoltaic system, Standards of solar photovoltaic system, Applications of PV
system, PV hybrid system.
(8 Hours)
UNIT-III
Biogas: Photosynthesis, Bio gas production Aerobic and anaerobic bio-conversion process, Raw materials,
Properties of bio gas, Producer gas, Transportation of bio gas, bio gas plant technology & status,
Community biogas plants, Problems involved in bio gas production,
Bio gas applications, Biomass conversion techniques, Biomass gasification, Energy recovery from
urban waste, Power generation from liquid waste, Biomass cogeneration, Energy plantation, Fuel
properties, Biomass resource development in India.
Wind energy: Properties of wind, Availability of wind energy in India, wind velocity, Wind machine
fundamentals, Types of wind machines and their characteristics, Horizontal and Vertical
axis wind mills, Elementary design principles, Coefficient of performance of a wind mill rotor,
Aerodynamic considerations in wind mill design, Selection of a wind mill, Wind energy farms,
Economic issues, Recent development.
(8 Hours)
UNIT-IV
Electrochemical effects and fuel cells: Principle of operation of an acidic fuel cell, Reusable cells, Ideal
fuel cells, Other types of fuel cells, Comparison between acidic and alkaline hydrogen-oxygen fuel
cells, Efficiency and EMF of fuel cells, Operating characteristics of fuel cells, Advantages of
fuel cell power plants, Future potential of fuel cells .
Tidal power: Tides and waves as sources of energy, Fundamentals of tidal power, Use of tidal energy
Limitations of tidal energy conversion systems.
Hydrogen Energy: Properties of hydrogen in respect of it's use as source of renewable energy, Sources of
hydrogen, Production of hydrogen, Storage and transportation, Problems with hydrogen
as fuel, Development of hydrogen cartridge, Economics of hydrogen fuel and its use..
(8 Hours)
UNIT-V
Thermoelectric systems: Kelvin relations, power generation, Properties of thermoelectric materials,
Fusion Plasma generators.
Geothermal energy: Structure of earth’s interior, Geothermal sites, earthquakes & volcanoes,
Geothermal resources, Hot springs, Steam ejection, Principal of working, Types of geothermal
station with schematic representation, Site selection for geothermal power plants.
Advanced concepts, Problems associated with geothermal conversion.
Ocean energy; Principle of ocean thermal energy conversion, Wave energy conversion machines,
Power plants based on ocean energy, Problems associated with ocean thermal energy conversion systems,
Thermoelectric OTEC, Developments of OTEC, Economics .
Impact of renewable energy generation on environment, Kyoto Protocol, Cost of
electricity production from different energy sources, Energy options for Indian economy.
(8 Hours)
Books / Reference:
Bansal Keemann, Meliss," Renewable energy sources and conversion technology", Tata Mc
Graw Hill.
Kothari D.P., “Renewable energy resources and emerging technologies”, Prentice Hall of India
Pvt. Ltd.
Rai G.D, "Non-Conventional energy Sources", Khanna Publishers.
Ashok V. Desai, "Nonconventional Energy", New Age International Publishers Ltd
B.Tech. Mechanical Engineering
Semester VII
CAD/CAM Lab
List of Experiments:
1) Line Drawing or Circle Drawing experiment: Writing and validation of computer program.
2) Geometric Transformation algorithm experiment for
translation/rotation/scaling: Writing and validation of computer program.
3) Component assembly in CAD and generating and modifying
Drawings.
4) CAD exercises using Auto Cad software
5) Part-programming on CNC machines
6) Execution of part programme for machining given profile.
7) Programming of robots for various applications.
8) Part modeling using some of the modeling technique
9) To study the characteristic features of CNC machine.
10) Experiment on difference between ordinary and NC machine, study or retrofitting.
11) Experiment on Robot and programs
B.Tech. Mechanical Engineering
Semester VII
AUTOMOBILE LAB
Course Code: ME-752 L T P Cr
0 0 2 1