Ece PDF

DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
DELHI TECHNOLOGICAL UNIVERSITY
(Formerly Delhi College of Engineering)
Course of Study
B. Tech. (ELECTRONICS AND COMMUNICATION ENGINEERING)
W.E.F. 2015-16 (2nd , 3rd, 4th year)
DRAFT EC-1
DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING
BACHELOR OF TECHNOLOGY
(ELECTRONICS & COMMUNICATIONENGINEERING)
I Year: Odd Semester
Teaching Scheme Contact Exam Duration Relative Weights (%)
Hours/Week (h)
S. Subject Course Title Subject Credit L T P Theory Practical CWS PRS MTE ETE PRE
No. Code Area
Group A
1 MA101 Mathematics - I ASC 4 3 1 0 3 0 25 - 25 50 -
2 AP101 Physics – I ASC 4 3 0 2 3 0 15 15 30 40 -
3 AC101 Chemistry ASC 4 3 0 2 3 0 15 15 30 40 -
4 ME101 Basic AEC 4 4 0 0 3 0 25 - 25 50 -
Mechanical
Engineering
5 ME103 Workshop AEC 2 0 0 3 0 3 - 50 - - 50
Practice
6 HU101 Communication HMC 3 3 0 0 3 0 25 - 25 50 -
Skills
Total 21 16 1 7
Group B
1 MA101 Mathematics - I ASC 4 3 1 0 3 0 25 - 25 50 -
2 AP101 Physics – I ASC 4 3 0 2 3 0 15 15 30 40 -
3 EE101 Basic Electrical AEC 4 3 0 2 3 0 15 15 30 40 -
Engineering
4 CO101 Programming AEC 4 3 0 2 3 0 15 15 30 40 -
Fundamentals
5 ME105 Engineering AEC 2 0 0 3 0 3 - 50 - - 50
Graphics
6 EN101 Introduction to AEC 3 3 0 0 3 0 25 - 25 50 -
Environmental
Science
Total 21 15 1 9
DRAFT EC-2
I Year: Even Semester
Teaching Scheme Contact Exam Duration Relative Weights (%)
Hours/Week
S. Subject Course Title Subject Credit L T P Theory Practical CWS PRS MTE ETE PRE
No. Code Area
Group A
1 MA102 Mathematics – ASC 4 3 1 0 3 0 25 - 25 50 -
II
2 AP102 Physics – II ASC 4 3 0 2 3 0 15 15 30 40 -
3 EE102 Basic Electrical AEC 4 3 0 2 3 0 15 15 30 40 -
Engineering
4 CO102 Programming AEC 4 3 0 2 3 0 15 15 30 40 -
Fundamentals
5 ME102 Engineering AEC 2 0 0 3 0 3 - 50 - - 50
Graphics
6 EN102 Introduction to AEC 3 3 0 0 3 0 25 - 25 50 -
Environmental
Science
Total 21 15 1 9
Group B
1 MA102 Mathematics – ASC 4 3 1 0 3 0 25 - 25 50 -
II
2 AP102 Physics – II ASC 4 3 0 2 3 0 15 15 30 40 -
3 AC102 Chemistry ASC 4 3 0 2 3 0 15 15 30 40 -
4 ME104 Basic AEC 4 4 0 0 3 0 25 - 25 50 -
Mechanical
Engineering
5 ME106 Workshop AEC 2 0 0 3 0 3 - 50 - - 50
Practice
6 HU102 Communication HMC 3 3 0 0 3 0 25 - 25 50 -
Skills
Total 21 16 1 7
DRAFT EC-3
II Year: Odd Semester
S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

No.
1. EE251 Electronic Instrumentation AEC 4 3 0 2 3 0 15 25 20 40 -
and Measurements
2. EC201 Analog Electronics – I DCC 4 3 0 2 3 0 15 25 20 40 -
3. EC203 Digital Design – I DCC 4 3 0 2 3 0 15 25 20 40 -
4. EC205 Signals & Systems DCC 4 3 0 2 3 0 15 25 20 40
5. EC207 Engineering Analysis & DCC 4 3 1 0 3 0 15 25 20 40 -
Design (Network Analysis
and Synthesis)
6. HU201 Engineering Economics HMC 3 3 0 0 3 0 25 - 25 50
Total 23
II Year:Even Semester

No.
1. EE262 Electromagnetics AEC 4 3 1 0 3 0 25 - 25 50 -
2. EC 202 Analog Electronics – II 4 3 0 2 3 0 15 25 20 40 -
DCC
3. EC204 Digital Design – II DCC 4 3 0 2 3 0 15 25 20 40 -
4. EC206 Communication Systems DCC 4 3 0 2 3 0 15 25 20 40 -
5. EC208 Computer Architecture DCC 4 3 0 2 3 0 15 25 20 40
6. MG201 Fundamentals of HMC 3 3 0 0 3 0 25 - 25 50
Management
7. Total 23
III Year: Odd Semester

No.
1. EC301 Digital 4 3 0 2 3 0
DCC 15 25 20 40
Communication
2. EC303 Linear Integrated 4 3 0 2 3
DCC 0 15 25 20 40 -
Circuits
3. ECxxx Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20/25 40/50
Elective Course -1
4. ECxxx Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20 40/50
Elective Course- 2 /25
5. UExxx University Elective 3 3 0 0 3 0
UEC 25 25 50 -
Course
6. HU303 Professional Ethics
HMC 2 2 0 0 3 0 25 - 25 50
& Human Values
Total 21
DRAFT EC-4
III Year: Even Semester

No.
1. EC VLSI Design DCC 4 3 0 2 3 0 15 25 20 40
302
2. EC Digital Signal DCC 4 3 0 2 3 0 15 25 20 40 -
304 Processing
3. EC306 Embedded DCC 4 3 0 2 3 0 15 25 20 40 -
Systems
Elective
Course -3
Elective
Course- 4
6. HU302 Technical HMC 2 2 0 0 3 0 25 - 25 50
Communication
Total 22
IV Year: Odd Semester

No.
1. EC B. Tech DCC
4
401 Project-I
2. EC403 Training
DCC 2
Seminar
3. EC405 Microwave 3 0 2 3 0
DCC 4 15 25 20 40 -
Engineering
4. EC407 Optical 3 0 2 3 0
DCC 4 15 25 20 40 -
Communication
5. EC Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20/25 40/50
4xx Elective
Course- 5
6. EC Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20 40/50
4xx Elective /25
Course- 6
Total 22
DRAFT EC-5
IV Year:Even Semester

No.
1. EC402 B. Tech DCC 8
Project-II
(Contd. From
VII Sem.)
2. EC Wireless DCC 4 3 0 2 4 - 15 25 20 40 -
404 Communication
3. EC Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20/25 40/50 -
406 Elective
Course- 7
4. EC Departmental DEC/GEC 4 3 0/1 2/0 3 0 15/25 25/- 20/25 40/50
4xx Elective
Course- 8
Total 20
List of Departmental Elective Courses

S.NO. SUBJECT SUBJECTS Elective No.
CODE
1. EC- 305 Semiconductor Device Electronics
2. EC – 307 Antenna Design DEC -1,DEC-2
3. EC - 309 Bio – Medical Electronics & Instrumentation
4. EC - 311 Algorithms Design And Analysis
5. EC – 313 Microprocessors And Interfacing
6. EC – 315 Computer Communication Networks
7. EC - 317 Operating Systems
8. EC – 319 CMOS Analog Integrated Circuits
9. EC – 321 IC Technology
10. EC - 323 Control Systems
11. EC - 308 Analog Filter Design DEC-3,DEC-4
12. EC – 310 Testing And Diagnosis Of Digital System
Design
13. EC – 312 Software Defined Radio And Cognitive
Radio
14. EC - 314 RF Design
15. EC – 316 Wireless Sensor Networks
DRAFT EC-6
16. EC – 318 RF Circuits in CMOS Technology
17. EC – 320 Soft Computing
18. EC – 322 Green Sensors
19. EC - 324 Nano Electronics
20. EC – 326 Data Converters
21. EC – 328 Speech Recognition
22. EC – 330 Digital Image Processing
23. EC - 332 Information Theory and Coding
24. EC - 409 Computer Vision DEC-5, DEC-6
25. EC –411 Bio – Medical Signal And Image Processing
26. EC – 413 Power Electronics
27. EC – 415 System On Chip Design
28. EC – 417 CAD For VLSI Design
29. EC – 419 Memory Design
30. EC – 421 Computer And Numerical Techniques In
Electromagnetics
31. EC – 423 Internet and Web Technologies
32. EC – 425 Mixed Signal Design
33. EC – 427 Information Theory and Coding
34. EC – 408 Low Power VLSI Design
35. EC – 410 Advanced Coding Theory DCE-7,DEC-8
36. EC- 412 Machine Learning
37. EC- 414 EMC / EMI
38. EC- 416 Pattern Recognition
39. EC- 418 Estimation And Detection Theory
40. EC – 420 Cloud Computing
41. EC – 422 Robotics & Machine Vision
42. EC – 424 Fault Tolerant Computing
43. EC – 426 Distributed Computing
44. EC – 428 Neuroelectronics
45. EC – 430 Advanced Computer Architecture
46. EC – 432 Bio – Impedance Based Measurements
47. EC – 434 Fundamentals of MIMO
48. EC – 436 Advance Microwave & Antenna Design
49. EC- 438 Radar and Satellite Communication
DRAFT EC-7
List of University Elective Courses
S.No. SUBJECT CODE SUBJECTS
1. CO351 Enterprise & Java Programming
2. CO353 E-commerce & ERP
3. CO355 Cryptography & Information Security
4. CO357 Operating System
5. CO359 Intellectual Property Rights & Cyber Laws
6. CO361 Database Management System
7. EC351 Mechatronics
8. EC353 Computer Vision
9. EC355 Embedded System
10. EC 357 Digital Image Processing
11. EC359 VLSI Design
12. EE351 Power Electronics Systems
13. EE353 Electrical Machines and Power Systems
14. EE355 Instrumentation Systems
15. EE357 Utilization of Electrical Energy
16. EE359 Non-conventional Energy Systems
17. EE361 Embedded Systems
18. EN351 Environmental Pollution & E- Waste Management
19. EN353 Occupational Health & Safety Management
20. EN355 GIS & Remote Sensing
21. EP351 Physics of Engineering Materials
22. EP353 Nuclear Security
23. HU351 Econometrics
24. MA351 History Culture & Excitement of Mathematics
25. ME351 Power Plant Engineering
26. ME353 Renewable Sources of Energy
27. ME355 Combustion Generated Pollution
28. ME357 Thermal System
29. ME359 Refrigeration & Air Conditioning
30. ME361 Industrial Engineering
31. ME363 Product Design & Simulation
32. ME365 Computational fluid dynamics
33. ME367 Finite Element Methods
34. ME369 Total Life Cycle Management
35. ME371 Value Engineering
36. MG351 Fundamentals of Financial Accounting and Analysis
37. MG353 Fundamentals of Marketing
38. MG355 Human Resource Management
39. MG357 Knowledge and Technology Management
40. PE351 Advance Machining Process
41. PE 353 Supply Chain Management
42. PE355 Work Study Design
43. PE357 Product Design & Simulation
44. PE359 Total Life Cycle Management
45. PE361 Total Quality Management
46. PT361 High Performance Polymers
47. PT363 Separation Technology
48. PT365 Non-Conventional Energy
49. PT367 Polymer Waste Management
50. PT369 Nanotechnology in Polymers
DRAFT EC-8
51. PT371 Applications of Polymer Blends and Composite
52. IT 351 Artificial Intelligence and Machine Learning
53. IT 353 Data Structures and Algorithms
54. IT 355 Communication and Computing Technology

55. IT 357 Internet and Web Programming
56. IT 359 Java Programming
1. Subject Code: EE 251 Course Title: Electronic Instrumentation and Measurements

2. Contact Hours: L: 3 T: 0 P: 2
3. Examination Duration (ETE )(Hrs.): Theory 3 Hrs Practical 0
4. Relative Weightage: CWS 15 PRS 25 MTE 20 ETE 40 PR 0
5. Credits: 4
6. Semester: III
7. Subject Area: DCC
8. Pre-requisite: Nil
9. Objective: To introduce fundamentals instrumentation and measurement
10. Details of Course
S.No. Contents Contact
Hours
1. Errors and Interface Signals in Measurement: Definitions, accuracy, 4
precision, resolution, sensitivity, relative error, absolute error, types of error,
capacitive interference, inductive interference and shielding, electromagnetic
interference and shielding, ground loop interference, input guarding to reduce
ground loop interference
2. Bridge Measurement: Wheat stone bridge, Kelvin double bridge, Maxwell 10
bridge, Hays bridge, Anderson bridge, Desauty bridge, Schering bridge, Weins
bridge.
3. Electronic Measurement of Basic Electrical quantities: Brief introduction of 10
electromechanical voltmeters, ammeters, electro dynamo type meters, analog
electronic DC voltmeters, analog electronic AC voltmeters like true r.m.s AC
voltmeters, peak reading electronic ac voltmeters, Ac Amplifier-Rectifier ac
voltmeters, Electronic ac ammeters, analog phase measurements, digital phase
detectors, frequency and time measurement, Resistance, capacitance and
inductance measurement
4. Sensors and Their Applications: Classification of sensors, sensor modeling 10
and characteristics, different types of sensors, Potentiometer, LDR ,Photo cell
,Photo diode, Phototransistors, IR emitter/detector, Thermal detector ,Optical
encoder ,Magnetic sensors, Hall Effect sensors, Piezoelectric crystal, Capacitive
sensors, inductive sensors Ultrasonic sensors, Pyroelectric sensors,
Tachometer ,Resolver, Strain gauge , Load Cell, Smart Sensors.
Measurement of physical parameters like pressure, temperature , level, flow,
thickness, acceleration, speed, displacement, humidity etc.
5. Electronics Instruments: Digital storage Oscilloscope(DSO), Current and 4
Voltage Probes, Function Generators, Spectrum analyzers.
DRAFT EC-9
6. Digital Interfaces in Measurement Systems: IEEE-488 instrumentation 4
bus(GPIB), GPIB bus structure and operation, Serial Data Communication links
like RS-232 C and D interface, RS-422, RS-423, and RS 485 Interface
,Universal Serial bus(USB), data Transmission on fiber optic cables, virtual
instruments..
TOTAL 42
11. Suggested Books
S.No. Name of Books / Authors/ Publishers Year of

Publication/
Reprint
1. Iintroduction to Instrumentation and Measurements by R. B. Northrop 2005
, CRC, 2nd Edition Prenticehall International
2 Students Reference Manual For Electronic Instrumentation Laboratories by S. 2004
Wolf and R. F.M. Smith, PHI, 2nd Edition(ISBN: 0130421820)
3. Modern Electronic Instrumentation and Measurement Techniques , A. D. 1990
Helfrick and W. D. Cooper, PHI
4. Mechatronics , A. Smaili and F. Mrad Oxford University Press 2009
1. Subject Code: EC 201 Course Title: Analog Electronics – I

3. Examination Duration (ETE ) (Hrs.): Theory 3 Hrs Practical 0
5. Credits: 4
6. Semester: III
9. Objective: To introduce p-n junction theory, operation of the semiconductor devices and their use in
basic electronic circuits.

Hours
1. Review of semiconductor physics, p-n Junction diode: Physical operation, I-V 8
characteristic and diode equation, Large-signal model, Concept of load line, p-
n junction capacitances (depletion and diffusion), small signal ( low and high
frequency) model, Breakdown in p-n diodes, Zener diode.
2. Diode Applications: Rectifier circuits, Zener diode based voltage regulators, 6
limiting and clamping circuits, voltage multipliers, switching behaviour of p-n
diode, SPICE model of p-n diode, an example of p-n diode data sheet.
3. Bipolar Junction Transistor(BJT): Physical structure and modes of operation, 10
BJT current components, The Ebers-Moll model, BJT characteristics, and large-
signal equivalent circuit, BJT Biasing for Discrete-Circuit Design, BJT small-
signal equivalent, Basic single- stage BJT amplifier configurations, BJT as a
switch, SPICE BJT model and simulation examples.
4. Metal oxide semiconductor Field Effect Transistors MOSFET: Physical structure 10
and V-I characteristics of Enhancement/Depletion- type MOSFETs (n/p-
DRAFT EC-10
channel), Biasing in MOS amplifier circuits, Small signal equivalent circuit of
MOSFET, Basic configurations of single-stage MOS amplifier circuits, MOSFET
as an analog switch, SPICE MOSFET models and simulation examples. The
Junction Field Effect Transistor (JFET): Physical structure, drain and transfer
characteristics, SPICE JFET model and simulation examples.
5. Multistage Amplifiers: Analysis of multistage amplifier using BJT and MOSFETs, 8
Significance of coupling and bypass capacitor, types of coupling: DC, RC and
Transformer.
Differential Amplifier: Large and small signal operation, differential and Common
mode operation, BJT and MOS based constant current sources as active loads,
Differential Amplifier with active load.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Microelectronics circuits by Sedra and Smith; Oxford university press 1982
2. Fundamentals of Microelectronics circuits by B. Razavi. 2012

3. Microelectronics by Millman and Grabel; Tata McGraw Hill 1987
4. Electronic Devices and Circuits by B Kumar and Shail Bala Jain, PHI 2007
1. Subject Code: EC 203 Course Title: Digital Design – I

5. Credits: 4
6. Semester: III
9. Objective: To introduce fundamentals of Digital Electronics
Hours
1. Introduction to Number Systems and Codes : Switching properties of Diodes, BJT 8
and FET, Logic gates, DTL, TTL, ECL, I2L, CMOS Gates and their parameters
and comparisons, Applications of switching transistors in bistable, monostable,
astable and Schmitt trigger circuits.
2. Boolean algebra, Switching Function, minimization of switching function: 6
Karnaugh map method and Tabulation Method don’t care terms and applications
with respect to code converters and Digital Comparators, etc.
3. Gated Flip Flops, Master Slave Flip Flop, Ripple and Parallel Counter, Up-Down 6
Counter, Shift Registers and Ring Counter, designing the combinational circuits
of the counters through Excitation Table.
4. Introduction to the circuits for Arithmetic Unit: Serial and parallel Binary Adders, 6
2’s compliment and principle of subtraction, Carry-Look Ahead Adder, and BCD
adder: Principles of multiplication, division in ALU.
DRAFT EC-11
5. Semiconductor memories: ROM, PROM, EPROM, EEPROM, Bipolar RAM, static 8
and dynamic RAM. Encoder and Decoder, Demultiplexer, multiplexer, Designing
combinational circuits with multiplexer, ROM ,PAL and PLA
6. Analog-to-Digital conversion:, dual slope integration method and voltage to 8
frequency conversion, principal of DVM. , counter type, successive approximation
type, Flash ADC , D-A converter: weighted resistors type, R2R ladder type.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Modern Digital Electronics by R. P. Jain (TMH) 2003
2 Digital Principles and Application by Malvino & Leach (TMH). 2014
3. Digital Electronics And Logic Design by M. Mano (PHI) 2008
4. Introduction To System Design Using Integrated Circuits byB.S. Sonde (New 1992
Age International).
5. Switching And Finite Automata Theory by Z. Kohavi (TMH). 2010
1. Subject Code: EC – 205 Course Title: Signals and Systems

3. Examination Duration (ETE) (Hrs.): Theory 3 Hrs Practical 0
5. Credits: 4
6. Semester: III
9. Objective: To introduce the concept of signals and systems and their applications in electronics
communication and engineering.
Hours
1. Introduction: Basic concepts & definitions of continuous and discrete time Signals 8
& their classification, continuous & discrete time system and their properties,
elementary Signals. Linear time invariant systems response for continuous time
systems and discrete time systems. Properties of continuous and discrete LTI
systems. System representation through differential equations and difference
equations.
2. Introduction to Fourier Transform Analysis: continuous and discrete time Fourier 10
series and its properties, Fourier Transform for continuous and discrete time
signals/system. Concept of bandwidth estimation for signal and system.
Magnitude and phase spectra of continuous and discrete time signal, response of
DRAFT EC-12
LTI system using Fourier transform. Application Fourier transform as linear
filtering.
3. The Laplace Transform. The Region of Convergence for Laplace Transforms. The 8
Inverse Laplace Transform. Geometric Evaluation of the Fourier Transform from
the Pole-Zero Plot. Properties of the Laplace Transform. Some Laplace Transform
Pairs. Analysis and Characterization of LTI Systems Using the Laplace
Transform. System Function Algebra and Block Diagram Representations. The
Unilateral Laplace Transform.
4. Z-Transform: Basic principles of z-transform, z-transform definition, Relationship 8

between z-transform and Fourier transform, Region of Convergence, Properties
of ROC, Properties of z-transform, Poles and Zeros, Inverse z-transform using
Contour integration, Residue Theorem, Power Series expansion and Partial
fraction expansion.
5. Sampling: Representation of continuous time signals by its sample –Types of 8
sampling, sampling theorem, aliasing, decimation, interpolation. Reconstruction
of a Signal from its samples. Mathematical Background: Representation of
signals using ortho-normal basis functions. Power and Energy spectral density.
Correlation functions. Hilbert Transform and its properties. Pre-envelope and
Complex Envelope. Band pass signals and Band pass systems.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Signals & Systems by Alan V. Oppenheim, Alan S. Willsky and S. Hamid 2013
Nawab, Pearson, Second Edition, Pearson Education, ISBN:81-7808-688-3
2. Signal & Systems by Simon Haykin and Barry Van Veen; Second Edition, 2003
John Wiley & Sons, ISBN : 0471- 16474-7
3. Linear systems and signals by B.P.Lathi, Oxford Publication 2004
4. Fundamentals of Signal & Systems using the Web and MATLAB, By Kamen 2007
: Pearson
5. Fundamentals of Signals and Systems, Third Edition, Edward W Kamen& 2006
Bonnie’s Heck, Prentice Hall.
6. Schaum's Outline of Signals and Systems, Third Edition, by Hwei P. Hsu, 1995
MGH
7. Fundamentals of Signals and Systems, Second Edition by Roberts, McGraw 2007
Hill
1. Subject Code: EC-207 Course Title: Engineering Analysis and Design (Network
Analysis and Synthesis)
DRAFT EC-13
4. Relative Weightage: CWS 25 PRS - MTE 25 ETE 50 PR 0
5. Credits: 4
6. Semester: III
9. Objective: To introduce fundamentals Engineering Analysis & Design (Network Analysis& Synthesis
Hours
1. Review of network elements: Linear versus nonlinear, time-variant and time 7
invariant, passive verses active, causal and non-anticipated, stable and unstable
networks, Network theorems: superposition, Thevenin and Norton's, maximum
power transfer, Star-Delta transformation.
2. Network graph theory, notations and definitions, incidence matrix, cut-sets and 7
fundamental loops, fundamental cutsets matrix, Kirchoff voltage law, Kirchoff
current law, interrelationship between matrices of a graph, Tellegen’s theorem
and its application.
3. Analysis of linear time invariant networks, transform methods in circuit analysis, 8
Laplace transform of common signals, concept of transformed impedance,
network functions, poles and zeros, impulse response, step response,
convolution.
4. Two-port network parameters: driving point and transfer functions. conversion, 7
various inter connections, analysis using various two port parameters.
5. State equations for networks. State variable analysis of circuits, formulation of 7
state equations, solution of state equations. Transient Response of RC, RL, RLC
Circuits to various excitation signals such as step, ramp, impulse and sinusoidal
excitations using Laplace Transform. Steady state sinusoidal analysis.
6. Network synthesis, positive real functions, driving point synthesis (RC,RL, LC, 6
)Introduction to passive filter.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Network Analysis” by M.E.Van Valkenburg, Third Edition; Prentice Hall, 1986
2. “Fundamentals of Network Analysis & Synthesis” by Behrouz Peikari; Jaico 2006
Publishing house.
3. Network Analysis & Synthesis” by F.F.Kuo; Wiley India edition, 2nd edition 2009
4. “Engineering Circuit analysis” by Hyat Jr. & Kemmerly, McGraw Hill 2006
1. Subject Code: HU201 Course Title: Engineering Economics

3. Examination Duration (ETE ) (Hrs.): Theory 03 Practical 0
5. Credits: 3
6. Semester: III
7. Subject Area: HMC
DRAFT EC-14
9. Objective: To enable the students to understand the economic theories which may be applied to maximize return
and economic environment in which they have to operate.
10. Details of Course:
Hours
1. 10
Introduction: Nature and significance of economics, Goods and Utility, Basic
Concept of Demand and Supply, Elasticity of Demand- Price elasticity of
Demand, Cross elasticity of Demand, Production - Production Function,
Production Process and Factors of Production, Market – Introduction to
Monopoly, Perfect Competition, Oligopoly and Monopolistic Competition, Cost
Concepts- Opportunity Cost, Total Cost, Average Cost; Marginal Cost; Life
Cycle cost, Sunk Cost; Preparation of Cost Sheet Profit Maximisation- numerical
problem.
2. 10
Money- its evaluation and function, Bank- Commercial Bank and Central Bank
and brief idea about function of banking system:. Tax and Subsidy, Type of
Tax- Direct and Indirect, Monetary and fiscal policy, Inflation and Business
cycle, International trade, terms of Trade, Gain from International Trade, Free
Trade vs. Protection, Dumping, Balance of Payment.
3. 12
Role of Science, Engineering and Technology in Economic Development:
Seven salient Feature of the Indian Economy; Inclusive Growth; relevance for
the Indian Economy; Globalisation & opening up of the Indian Economy; GDP-
definition and Its measurement; How knowledge of engineering and ology may
be used to improve life at slum; Green Revolution and White revolution.
Reasons for their success and can we replicate them. Appropriate Technology
& Sustainable Development. Entrepreneurship: Macro environment for
promotion of entrepreneurship: How environment has changed after advent of
IT and Globalisation.
4. 10
Elementary Economic Analysis: Interest formulas and their Applications;
Calculations of economic equivalence, Bases for Comparison of Alternatives:
Present Worth Method, Future worth method, Annual equivalent, Internal Rate
of Return; Business Risk; Factors which should be taken care while deciding
price of the product in the market.
TOTAL 42
11. Suggested books

Publication/
Reprint
1. Engineering Economy, Engi G.J. Thuesen, & W.J. Fabrycky, Prentice- (2007)
Hall of India Private Limited.
2. Engineering Economy, William G. Sullivan, James A. Bontadelli & Elin M. 2009
Wicks, Pearson Education Asia,( First Indian reprint).
3. Engineering Economic Analysis, Donald G. Newman, Jerome P. Lavelle & 2001
Ted G. Eschenbach, , Engineering Press.
4. Economics for Engineering Students, Seema Singh, , IK International 2014
Publishing House Pvt. Ltd
DRAFT EC-15
DRAFT EC-16
IVth SEMESTER
1. Subject Code: EE – 262 Course Title: Electromagnetics

5. Credits: 4
6. Semester: IV
7. Subject Area: AEC
9. Objective: To introduce fundamentals of Electromagnetics
Hours
1. Vector Analysis: Review of Coordinate systems and Transformations– 4
Cartesian, Circular and Spherical coordinates and Transformations. Vector
Calculus – Differential length, Area and Volume; Line, Surface and Volume
Integrals; Del Operator, Gradient of a Scalar, Divergence of a vector and
Divergence theorem, Curl of a vector and Stokes theorem.
2. Electrostatics and Magneto statics : Electric field due to various distributed 10
charge distributions, Gauss’s law and its applications, Electric energy and
Capacitance, Electric Boundary conditions; Poisson’s and Laplace equations,
Method of images. Biot Savart’s law, Ampere’s circuit law and its applications,
Magnetic boundary conditions, Magnetic energy and Inductance.
3. Maxwell’s Equation: Continuity equation and Relaxation Time, Faraday’s law, 10
Displacement current, Maxwell equations in their general time varying forms,
Special cases of Maxwell’s equations for Good dielectrics, Good conductors
and for Time-Harmonically varying Fields, Significance of loss tangent.
4. Electromagnetic Wave Propagation: Electromagnetic Wave Equation in a 10
general medium and its solution, Wave propagation in lossless and lossy
dielectrics, Plane waves in free space, Plane waves in good conductors, Power
and Poynting’s vector, Reflection and refraction of plane waves at normal and
oblique incidence.
5. Transmission Lines: Transmission line parameters and equations; Input 4
impedance, VSWR, and Power; Complex reflection coefficient, Short and Open
Circuit Stubs, Smith Chart, Some applications of Transmission lines, Transients
on transmission lines, Microstrip transmission lines.
6. Waveguides: Rectangular waveguides, Field equations for Transverse Electric 4
and Magnetic modes, Wave propagation in the guide and its propagational
characteristics, Power transmission and attenuation, Waveguide current and
mode excitation, Waveguide resonators. Application in Non Destructive
Testing.
TOTAL 42
DRAFT EC-17
11. Suggested Books
Publication/
Reprint
1. Elements of Electromagnetics by M. N. O. Sadiku, Oxford University Press 2005
2. Engineering Electromagnetics by Hayt and Buck, Tata McGraw Hill. 2004
3. Fields and Waves in Communications Electronics by Ramo, Whinnery and Van 1994
Duzer, John Wiley & Sons
4. Field and Wave Electromagnetics by David K Cheng, Pearson Education 2nd
(India).
1. Subject Code: EC 202 Course Title: Analog Electronics – II

5. Credits: 4
6. Semester: IV
9. Objective: To familiarize students to the analysis and design of analog electronic circuits which form
the basic building blocks of almost any electronic system.

Hours
1. Frequency Response: s-Domain analysis: Poles, Zeros, and Bode plots, the 8
amplifier transfer function, Low-frequency/ high-frequency response of common-
source/common emitter amplifiers, common-base/ common-gate amplifier,
frequency-response of emitter and source follower.
2. Frequency response of cascaded stages: Cascode configurations, the common- 8
collector and common emitter cascade, frequency response of the differential
amplifier. SPICE simulation example.
3. Feedback: Properties of feedback amplifiers, basic feedback topologies, analysis 10
and characteristics of various feedback amplifier circuits. Loop gain, stability
problem, effect of feedback on the amplifier poles, stability study using bode
plots, frequency compensation.
4. Principles of oscillations, Barkhausen criterion, Frequency stability, Various 10
types of oscillators: RC Phase shift, Wein bridge, Hartley, Colpitt, Crystal
oscillators. Amplitude limiter circuits.
Output stage and Power Amplifiers: Classification of output stages, class A, B
and AB output stages, Biasing the class AB circuit, variations on the class AB
configuration, Power BJTs, MOS power transistors, IC power amplifiers.
5. Microelectronic Technology, Planar process, Fabrication: Bipolar Transistor, 6
FET, CMOS; Monolithic diodes, Metal semiconductor contact, Integrated circuit
resistors and capacitors, Integrated circuit packaging, Characteristics of
integrated circuit components, Microelectronic circuit layout .
TOTAL 42
DRAFT EC-18
11. Suggested Books
Publication/
Reprint
1. Microelectronics circuits by Sedra and Smith; Oxford university press 1982
2 Fundamentals of Microeletronics by Razavi; Wiley 2012
3. Microelectronics by Millman and Grabel; Tata McGraw Hill 1987
4. Electronic Devices and Circuits by B Kumar and Shail Bala Jain, PHI 2007
5. Microelectronics circuits by Rashid, PWS Publishing Company 2000
1. Subject Code: EC 204 Course Title: Digital Design – II

5. Credits: 4
6. Semester: IV
9. Objective: To introduce fundamentals of VHDL and Digital Electronics

Hours
1. Digital system design with VHDL/Verilog: Introduction, language fundamentals, 10
Verilog Primitives, User Primitives, Data Types, Operators, Design examples.
High level description of standard combinational and sequential modules.
2. Introduction to finite state machine: pulse and fundamental mode of operation, 6
realization of state table from verbal description, state diagram & Transition
matrix, Mealy and Moore model machine.
3. Reduction of flow tables of completely and incompletely specified sequential 6
machines, concept of secondary state assignment and realization of circuits of
FSM,
4. Decomposition of FSM & composite machine equivalence between Mealy and 8
Moore model machine. Race and Hazard problems with asynchronous
sequential machine stuck-at and bridging faults
5. Introduction to design with the programmable modules: 6
ROM, PAL, PLA, FPGA , ASIC
6. Algorithmic state machine: ASM Chart, data and control subsystem and 6
implementation of ASM.
Introduction to ASM designing with microprogramming.
TOTAL 42
11. Suggested Books

Publication/
Reprint
DRAFT EC-19
1. A Verilog HDL Primer by J. Bhaskar; BS Publication. 2001
2. Switching And Finite Automata Theory by Z. Kohavi; TMH. 2009
3. Verilog Digital Systems Design by Z. Navabi; Tata McGraw Hill. 2003
4. Fundamental of Logic Design by Roth ; Cengage learning. 2013
5. Advanced Digital design with Verilog HDL by Michael D Ciletti 2010
6. Digital Logic State Machine Design” by D.J. Comer; Oxford University Press. 2012
7. Contemporary Logic Design by R.H.Katz, G.Borriello; PHI. 2002
8. Introduction To Digital Systems by M.Ercegovac, T. Lang and J.H.Morcno; 2006

Wiley Int.
9. Verilog HDL Palnitkar ; Pearson 2010
1. Subject Code: EC –206 Course Title: Communication Systems

2. Contact Hours: L: 3 T: P: 2
5. Credits: 4
6. Semester: IV
8. Pre-requisite: Signals and Systems, Probability and stochastic process.
9. Objective: To introduce the fundamentals of electronics Communication Systems and their
terminologies and applications.
Hours
1. Introduction to Communication systems, source of information, communication 6
channels, base band pass band signals, representation of signals and systems,
probabilistic considerations, modulation process, primary communication
resources, analog versus digital communication, applications of communications
systems.
2. Linear modulation: Time and frequency domain expression of AM (including 10
intensity modulation of light), DSB, SSB and VSB; generation of linearly
modulated signals. Coherent demodulation and envelope detection. Angle
modulation: Instantaneous frequency; phase and frequency modulation. Single
tone FM and its spectral analysis. NBFM and WBFM. Bandwidth requirements
of angle modulated signals. Demodulation of angle modulated signals
3. Radio and Television broadcasting: AM radio broadcasting and FM radio and TV 8
broad casting. Frequency division multiplexing, radio transmitters and receivers,
sampling theory, pulse code modulation and demodulation, delta modulation and
adaptive delta modulation.
4. Noise in Communication systems: Thermal noise, shot noise and white noise. 10
Noise equivalent bandwidth, noise figure and noise temperature. Time domain
representation of narrowband noise. Properties of narrowband noise. Noise in
CW modulation systems.
DRAFT EC-20
5. Figure of merit: Noise performance of linear and exponential modulation. Pre- 8
emphasis and de-emphasis in FM. Comparison of the noise performance of CW
modulation schemes.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1 “Communication System by Simon Haykin John Wiley & sons. 3rd Edition
2. Principles of Communication System by Taub & Schilling ,TMH 4th Edition
3. Communication Systems by Proakis John Wiley & sons. 2nd Edition
4. Modern analog and digital communication by B.P. Lathi , Oxford 4th Edition
5. Electronic Communication Systems by Kennedy , Tata McGraw-Hill 5th Edition
1. Subject Code: EC 208 Course Title: Computer Architecture

5. Credits: 4
6. Semester: IV
9. Objective: To introduce fundamentals concepts of computer architecture.
Hours
1. Overview of Digital Fundamentals, Register Transfer and Micro operation: 8
Register Transfer Language, Register Transfer, Bus and Memory Transfer,
Arithmetic Micro operations, Logic Micro operations, Shift Micro operations,
Design of ALU.
2. Computer Organization and Design: Instruction Codes, Computer Registers, 8
General Register Organization, Stack Organization, Instruction Formats,
Addressing Modes, , Timing & Control, Instruction Cycle, Memory Reference
Instructions, Input-Output and Interrupt related instruction cycle, Design of
Hardwired and Microprogrammed Control Unit, Microprogramming .
3. Input – Output Organization: Peripheral devices, Input – Output interface, 4
Asynchronous Data Transfer, Modes of Data Transfer, Priority Interrupt,
Direct Memory Access, Input – Output Processor.
4. Memory: Memory hierarchy, Main Memory, Auxiliary Memory, Associative 8
Memory, Cache Memory, Virtual Memory, Memory Management Hardware.
5. Computer Arithmetic: Introduction, Addition and Subtraction, Multiplication 8
Algorithms, Division Algorithms, Floating Point Arithmetic Operation, Decimal
Arithmetic Unit, Decimal Arithmetic Operations. Hardware implementation of
arithmetic algorithms.
Introduction to RISC , Parallel Processing, Concept of Pipelining, Arithmetic 6
6. Pipelining, Instruction Pipelining, Vector Processing, Array Processors.
TOTAL 42
DRAFT EC-21
11. Suggested Books
Publication/
Reprint
1. Computer System and Architecture by PHI, Mano M. 2006
2. Computer Systems Organization and Architecture by Carpinelli; Pearson 2001

Education.
3. Computer Architecture and Organization by Hayes. J.P.; TMH. 2000
4. Computer Organization & Design by Pal Chaudhuri, P; PHI. 2004
5. Computer Organization & Architecture, by Stallings, W; PHI. 2012
6. Parallel Processing and Architecture by K.Hwang and F.Briggs; McGraw Hill 1984
7. Computer Architecture: A Quantitative Approach by D. Patterson and J. 2002

Hennessy, Second Edition; Morgan.
1. Subject Code : MG201 Course Title : Fundamentals of Management

4. Relative Weightage : CWS 25 PRS 0 MTE 25 ETE 50 PR 0
5. Credits: 3
6. Semester: IV
9. Objective: The basic objective of this paper is to acquaint the students with the basic concepts
of management necessary to deal with emerging business environment besides sensitizing them about
societal challenges.
S.No. Detail Contents Contact
Hours
1. Definition of management, importance of management, management 8
principals, managerial roles, managerial ethos, management vs administration,
managerial functions, task and responsibilities, organizational structure,
motivation: meaning, theories and techniques.
2. Concept of business environment, corporate social responsibility and corporate 8
governance, managerial values and ethics.
3. Objectives and importance of financial management, basics of capital 9
budgeting, cost of capital, emerging sources of funds for new projects,
introduction to stock market.
4. Functions of marketing, marketing Vs sales, interface of marketing with other 8
departments, customer life time value, new product development, unethical
issues in marketing.
5. Introduction to knowledge management, knowledge society, knowledge 9
economy, building knowledge assets, sources of knowledge, technology
innovation process, E-governance: definition, objectives and significance;
challenges in Indian context, Digital India programme.
Total 42
DRAFT EC-22
11. Suggested Books
S. No. Name of Books / Authors/ Publishers Year of
Publication/
Reprint
1. Fundamental of Management, Stephen P. Robbins, David A. De Cenzo and 2011
Mary Coulter, Pearson Education,( ISBN:9780273755869)
2. Financial Accounting, 4 ed, S.N. Maheshwari and S.K. Maheshwari, Vikas 2005
Publication,(ISBN: 8125918523)
3. Management, James A F Stonner, Pearson Education, (ISBN: 2010
9788131707043)
4. Marketing Management, 14th ed., Philip Kotler , Kevin Lane Keller, Abraham 2013
Koshy and Mithileswar Jha, Pearson Education, (ISBN: 9788131767160)
5. Knowledge Management in Organizations: A Critical Introduction, Donald 2013
Hislop, Oxford University Press, ISBN: 9780199691937.
Vth SEMESTER
1. Subject Code: EC301 Course Title: Digital Communication

3. Examination Duration (Hrs.): Theory: 03 Practical: 00
4. Relative Weight: CWS: 15 PRS: 25 MTE: 20 ETE: 40 PRE: ---
5. Credits: 4
6. Semester: V
8. Pre-requisite: NIL
9. Objective:To familiarize the students with the concepts of basics of Digital Communication.
S. No. Contents Contact

Hours
Analog Pulse Modulation: Generation and Demodulation of Pulse Amplitude
Modulation, Pulse Width Modulation, Pulse Position Modulation, PAM/TDM
System, Spectra of Pulse Modulated Signals, SNR Calculations for Pulse
1. Modulation Systems. 10
Waveform Coding: Sampling Theorem for Band Pass Signals, Quantization,
PCM, DPCM, Delta Modulation, Adaptive Delta Modulation- Design of Typical
Systems and Performance Analysis.
Baseband Shaping for Data Transmission: Discrete PAM Signals, Power
Spectra of Discrete PAM Signals, Pulse Shaping, Inter Symbol Interference,
Nyquist Criterion for Zero ISI & for Distortion-less Baseband Binary
2. 06
Transmission, Correlative Coding, Signaling with Duo-Binary Pulses, Eye
Diagram, Equalization, Adaptive Equalization for Data Transmission, Scrambling
and Descrambling.
Signal space concepts: Analogy between Signals and Vectors, Geometric
Structure of the Signal Space, L2 Space, Distance, Norm and Inner Product,
3. Decomposition of a Signal and Signal Components, Complex Signal Space and 06
Orthogonality, Orthogonal Signal Set, Base-Band Pulse Data Transmission,
Gram-Schmidt Orthogonalization Procedure.
Detection and Estimation: Review of Gaussian Random Process, Detection of
Known Signals in Noise, Optimum Threshold Detection, Optimum Receiver for
AWGN Channel, Matched Filter and Correlation Receivers, Decision Procedure:
4. 06
Maximum A- Posteriori Probability Detector- Maximum Likelihood Detector,
Probability of Error, Bit Error Rate, Wiener Filter for Waveform Estimation, Linear
Prediction.
DRAFT EC-23
Digital modulation schemes: Coherent Binary Schemes: ASK, FSK, PSK, MSK,
GMSK. Coherent M-ary Schemes, Non-Coherent Schemes, Calculation of
Average Probability of Error for Different Modulation Schemes, Power Spectra
of Digitally Modulated Signals, Performance Comparison of Different Digital
5. Modulation Schemes. DQPSK, QPSK, OQPSK, pi/4 QPSK, 8-PSK, 16 QAM, 64 10
QAM. Trellis Coded Modulation, A discussion on various Modulation Schemes
used in various standards such as GSM, IS-95, IS-56, CDMA. A review on
adaptive Modulation Schemes for Transmission of Voice and Data over Fading
Channel.
Spread Spectrum Modulation: Pseudo-Noise Sequences, Direct Sequence
Spread Spectrum [DSSS], Resistance to Jamming, Signal-Space 4
6.
Dimensionality, Processing Gain, Frequency-Hop Spread Spectrum, Acquisition
and Synchronization, Applications.
TOTAL 42
11. Suggested Books:
S. Name of Authors /Books / Publishers Year of

No. Publication/
Reprint
1. Digital Communication Systems by Simon Haykin; John Wiley & Sons. 2009
2. Modern Digital and Analog Communication, 3rd Edition by B.P. Lathi; Oxford 2009
University Press.
3. Digital Communication, 2E by Sklar; Pearson Education. 2001
4. Digital and Analog Communication Systems by K.Shanmugham; John Wiley & 1994
Sons.
5. Analog and Digital Communication by Couch, Pearson Education.
6. Digital Communications by John G. Proakis; McGraw Hill. 2000
7. Principles of Communication Systems by H. Taub and Schilling; TMH. 1998
1. Subject Code: EC 303 Course Title: Linear Integrated Circuits

5. Credits: 4
6. Semester: V
8. Pre-requisite: EC 201, EC 202
9. Objective: To introduce Op Amp; a versatile building block and to design analog circuits and
systems for signal conditioning, processing and generation functions.
Hours
1. Operational Amplifier: The ideal Op Amp, Building blocks of analog ICs: current 10
mirrors and repeaters, current and voltage sources, differential amplifiers, input
stages, active load, gain stages, output stages, level shifters, non ideal parameters,
Monolithic IC operational amplifiers, specifications, slew rate and methods of
improving slew rate.
2. Linear applications of IC op-amps: Inverting and non-inverting amplifier 10
configurations, integrators, differentiators, summers, effect of infinite GBP, stability
consideration, active and passive compensation of op-amp. Non-Linear
applications of IC op-amps: Log/ antilog modules, Precision Rectifier, Op-amp as
comparator, Schmitt Trigger, Square and Triangular wave generator, mono stable
and astable multivibrators.
DRAFT EC-24
3. Analog filter design : Basics second order functions, op-amp RC and active filter 10
design, immittance converters and inverters, generalized impedance converter,
inductance simulation, Sinusoidal oscillators, amplitude stabilization and control.
Operational Transconductance Amplifier (OTA), Basic building blocks using OTA,
Application examples
4. Analog Multiplier and its applications: Gilbert multiplier cell 2-quadrant and 4- 6
quadrant operations, IC analog multiplier AD534, modulation, demodulation and
frequency changing, voltage-controlled filters and oscillators.
5. IC timer and phase locked loop: the IC 555 timer, operational modes, time delay, 6
asable and monostable operations , voltage-controlled oscillators, IC PLL: basic
PLL principle, three modes of operation, PLL as AM detector, FM detector,
frequency synthesis, FM demodulator, PLL motor speed control and voltage to
frequency converter.
Total 42
11. Suggested Books

Publication/
Reprint
1. Applications and Design with Analog Integrated Circuits by J. Michel Jacob, PHI 2004
2. Rolf Schaumann and Mac E.VanValkenburg by Oxford Indian Edition 2005

3. Analysis and Design of Analog Integrated Circuits by, Paul R.Gray/Robert 2009
G.Meyer, Wiley, Third edition
4. Design with Operational Amplifiers and Analog Integrated Circuits by Sergio 2013
Franco, TMH.
5. Microelectronic circuits: Analysis and Design by M.H. Rashid, 2nd edition, 2009
CENGAGE Learning
1. Subject Code: HU 303 Course Title: Professional Ethics and Human Values
5. Credits: 2
6. Semester: V
9. Objective Processes: To make students aware of the ethics and codes of conduct required by Engineers and
Professionals.
S.No. Name of Books, Authors, Publishers Contact

Hours
Human Values and Ethics: Morals, Values, Ethics and Integrity, Need for Value
1. Education for Engineers, Happiness, Prosperity, Harmony.
DRAFT EC-25
6
2. Code of Ethics and Professionalism: Professionalism and the Code of Ethics,
Technical Education, Human Values and Coexistence, Universal Human Order,
Natural acceptance. 6
3. Professional Ethics and Technology :Science, Technology and Professional
Ethics Engineering Ethics, Environmental Ethics, Safety, Responsibility and 8
Rights.
4. Case Studies: Holistic Technologies, Eco-friendly production systems, The role of 8
responsible engineers and technologists, Global Issues concerning Engineers.
TOTAL 28
11. Suggested Books
S.No. Name of Books, Authors, Publishers Year of

Publication
/Reprint
1. Professional Ethics, Subramanian, R, Oxford University Press, ISBN13: 978-0- 2011
19-808634-5
2. Professional Ethics and Human Values, Govindarajan, M. S. Natarajan, V.S. 2013
Senthil kumar PHI, ISBN: 978-81-203-4816-5
3. Constitution of India and Professional Ethics, Reddy, G.B. and Mohd. Suhaib, IK 2006
International Publishing House. ISBN: 81-89866-01-X
4. Introduction to Engineering Ethics (2nd Ed.)Martin, Mike W. and Roland 2010
Schingzinger McGraw-Hill ISBN 978-0-07-248311-6
VIth SEMESTER
1. Subject Code: EC 302 Course Title: VLSI Design

5. Credits: 4
6. Semester: VI
9. Objective: To give the student an understanding of the different design steps required to carry out a
complete digital VLSI (Very-Large-Scale Integration) design in silicon.
10.Details of Course

Hours
1. Introduction to VLSI, Manufacturing process of CMOS integrated circuits, CMOS 6
n-well process design rules, packaging integrated circuits, trends in process
technology.
MOS transistor, Energy band diagram of MOS system, MOS under external bias,
derivation of threshold voltage equation, secondary effects in MOSFETS
2. MOSFET scaling and small geometry effects, MOS capacitances, Modeling of 6
MOS transistors using SPICE, level I II and equations, capacitance models.
The Wire: Interconnect parameters: capacitance, resistance and inductance.
Electrical wire models: The ideal wire, the lumped model, the lumped RC model,
the distributed RC model, the transmission line model, SPICE wire models.
DRAFT EC-26
3. MOS inverters: Resistive load inverter, inverter with n-type MOSFET load, CMOS 8
inverter: Switching Threshold, Noise Margin, Dynamic behavior of CMOS inverter,
computing capacitances, propagation delay, Dynamic power consumption, static
power consumption, energy, and energy delay product calculations, stick
diagram, IC layout design and tools.
4. Designing Combinational Logic Gates in MOS and CMOS: 8
MOS logic circuits with depletion MOS load.
Static CMOS Design: Complementary CMOS, Ratioed logic, Pass transistor logic,
BiCMOS logic, pseudo nMOS logic,
Dynamic CMOS logic, clocked CMOS logic CMOS domino logic, NP domino logic,
speed and power dissipation of Dynamic logic, cascading dynamic gates.
5. Designing sequential logic circuits: Timing matrices for sequential circuits, 8
classification of memory elements, static latches and registers, the bistability
principle, multiplexer based latches , Master slave Edge triggered register , static
SR flip flops, dynamic latches and registers, dynamic transmission gate edge
triggered register, the C2MOS register
6. Pulse registers, sense amplifier based registers, Pipelining, Latch verses Register 6
based pipelines, NORA-CMOS. Two-phase logic structure; VLSI designing
methodology –Introduction, VLSI designs flow, Computer aided design
technology: Design capture and verification tools, Design Hierarchy Concept of
regularity, Modularity & Locality, VLSI design style, Design quality.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Digital integrated circuits a design perspective by Jan M Rabaey, Anantha 2011
Chadrakasan Borivoje Nikolic, Pearson education.
2. CMOS digital integrated circuits by Sung MO Kang Yusuf Leblebici, Tata 2002
McGraw Hill Publication
3. Principle of CMOS VLSI Design by Neil E Weste and Kamran Eshraghian, 2000
Pearson education.
1. Subject Code: EC 304 Course Title: Digital Signal Processing

5. Credits: 4
6. Semester: VI
8. Pre-requisite: Signals and Systems, Communication System
9. Objective: To introduce the fundamentals of digital processing of the signals and systems, which
includes conversion analog to digital signals/system, realization of systems, computation of DFT and its
algorithms, Multi-rate signal processing, concept of finite word length and DSP processors.
DRAFT EC-27
Hours
1. Review: Basic elements of a DSP system, Analog to digital conversion, Digital 8
processing of Analog signals, Z-Transform and its properties. Computation of
DFT : Review of DFT and its properties, DFT as a linear transformation. Efficient
computation of DFT, Decimation in time Algorithm, Decimation in frequency
algorithm, Chirp-z and Goertzel Algorithm, Implementation of FFT Algorithms.
2. General difference equation, Implementation of Discrete Time Systems : 8
Structure of FIR systems: Direct form, Cascade form, frequency sampling, and
lattice. Structure of IIRsystems: Direct form, Cascade form, parallel form, Lattice
and Lattice-Ladder.
3. Design of Digital Filters: FIR Filters : Design of FIR filters using windows, Design 8
of FIR filters using frequency sampling method, Design of FIR differentiator.
Design of IIR Filter: Impulse Invariance Method, Bilinear t r a n s f o r m a t i o n s ,
d e s i g n e x a m p l e s : B u t t e r w o r t h l o w p a s s , Frequency transformations
and Least square inverse method.
4. Multirate D i g i t a l Signal Processing: Decimation, Interpolation, sampling rate 6
conversion, polyphase representation, multistage implementation, 2 channel
maximally decimated perfect reconstruction filter banks, 2 channel Paraunitary
filter banks , Applications.
5. Concept of finite word length in DSP, fixed and floating point numbers, 6
representation of negative number, effect of truncation, finite word length effect
in realization of IIR and FIR system. Fundamentals of adaptive filters and
applications, system identification, adaptive channel equalization, echo
cancelation in data transmission,
6. Introduction to Digital Signal Processors: Fixed point and Floating point 6
processors, architectures. TMS 320C54XX and TMS320C67XX Architecture,
Memory, Addressing Modes, filter implementation on fixed and floating point
processors.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Digital Signal Processing/ Oppenheim and Schafer/ PHI 2005
2 Digital signal Processing-Principles ,algorithms ,and applications , J G Proakis, 4TH Edition

DG Manolakis and D. Sharma, Pearson Education / 2004
3. Digital Signal Processing, S.K. Mitra THM Third
Edition
4. Digital Signal Processing Matlab Based Approach/ Ingle/ Cengage Learning. 1990
5. Digital signal Processor: Architectures, Implementations and Applications/ Sen M. 2005
Kuo and Woon-Seng Gan/ Pearson Education
6. Digital Signal Processing: Fundamentals and Applications/ Li Tan/ Elsevier 2009
Publications
DRAFT EC-28
1. Subject Code: EC 306 Course Title: Embedded Systems
3. Examination Duration (ETE)(Hrs.): Theory 3 Hrs Practical
5. Credits: 4
6. Semester: VI
8. Pre-requisite: Knowledge of Computer Architecture and Microprocessors
9. Objective: To introduce fundamentals of 16 and 32 bit Microcontrollers, assembly language
programming. The course also focuses on interfacing of different interrupt driven peripherals. It also covers
in detail Real Time Operating Systems, Bus architecture, Digital Signal Processors and System On-Chip.
Hours
1. Overview of Embedded Systems: Characteristics of Embedded Systems. 8
Comparison of Embedded Systems with general purpose processors. General
architecture and functioning of micro controllers. PIC and 8051 micro controllers
: Architecture, memory interfacing , interrupts, instructions, programming and
peripherals .
2. ARM : Architecture, memory interfacing , interrupts, instructions and Assembly 12
Language programming. Exception processing and pipeline architecture and
applications.
3. Digital Signal Processors: DSP Architecture, DSP applications, algorithms, data 4
path, memory, addressing modes, peripherals. TI and Sharc family of DSP
processors.
4. System On Chip : Evolution, features, IP based design, TI OMAP architecture 4
and peripherals. Digital Multimedia processor: Architecture and peripherals.
5. SRAM, DRAM working and organization. Interfacing memory with ARM 7. 4
Elements of Network Embedded Systems
6. RTOS : RT-Linux introduction, RTOS kernel, Real-Time Scheduling 10
Bus structure: Time multiplexing, serial, parallel communication bus structure.
Bus arbitration, DMA, PCI, AMBA, I2C and SPI Buses.
TOTAL 42
11. Suggested Books

Year of
S.No. Name of Books / Authors/ Publishers Publication/
Reprint
1. Computers as components: Principles of Embedded Computing System 2000
Design, Wayne Wolf, Morgan Kaufman Publication
2. ARM System Developer’s Guide: Designing and Optimizing System Software, 2004
Andrew N. Sloss, Dominic Symes, Chris Wright, , Morgan Kaufman
Publication
3. Design with PIC Microcontrollers, John B. Peatman, Pearson Education Asia 2002
4. The Design of Small-Scale embedded systems, Tim Wilmshurst, Palgrav 2003

5. Embedded System Design, Marwedel, Peter, Kluwer Publishers 2004
DRAFT EC-29
1. Subject Code: HU 302 Course Title: Technical Communication
2 . Contact Hours: L: 2 T: 0 P: 0
5. Credits: 2
6. Semester: VI
9. Objective Processes: To train students for business communication to enhance employability skills with special
emphasis on placement interviews and public speaking.
S. No. Contents Contact Hours

1. English for Professional Purposes: 1
1.Technical Communication- Methods, Strategies and Skills
2. Communication in Global Contexts- Social, Cultural, Political and
Technical, especially in formal set up 2
2. Communication at the Workplace: Oral and Written:
1. Written Communication- Letters, Orders (Sale/Purchase) Report 6
Writing, Technical proposals Resume, SOP, Memo, Notice, Agenda,
Minutes, Note Taking/Making,
2. Oral Communication: Seminars, Conferences, Meetings, Office
Etiquettes/ Netiquettes, Presenting Written Material Negotiation,
Demonstration, Group Discussion, Interview 6
Group Discussion and Report Writing:
3. 1. Group Discussion ( Continous assessment through the semester)
2. Minor Report Writing( to be submitted before Mid- Semester 13
Examination)
3. Major Report writing ( To be submitted
before End Semester Examination)
Total 28
11. Suggested Books

S.No. Name of Books, Authors, Publishers Year of
Publication/
Reprint
1. Technical Communication: Principles and Practice Raman, Meenakshi 2011, Reprinted
and Sangeeta Sharma, Oxford University Press, ISBN-13: 978-0-19- 2014
806529-6
2. Writing to Get Results, (3rd Ed) Blicq, Ron S., Lisa A. Moretto, John 2001
Wiley and Sons, Inc. ISBN 0-7803-6020-6
Effective Technical Communication: A Guide for Scientists and 2006
3.
Engineers , Mitra, Barun K. OUP: Delhi ISBN-13: 978-0-19-568291-5
Personality Development and Soft Skills, Mitra, Barun K. New 2014
4.
Delhi:Oxford University Press.ISBN-9780198060017
The Essence of Effective Communication, Ludlow, Ron and Fergus 1996
5.
Panton. Prentice Hall: PHI. ISBN-81-203-0909-X
Advanced Technical Communication, Gupta, Ruby. Foundation Books, 2011
6.
CUP. ISBN 978-81-7596-733-5
Soft Skills: Enhancing Employability, Rao, M.S. Connecting Campus with 2011
8.
Corporate ISBN: 978-93-80578-38-5
DRAFT EC-30
Developing Communication Skills (2nd Ed), Mohan, Krishna and Meera 2009
9.
Bannerji, Macmillan Publishers India Ltd. ISBN 13: 978=0230-63843-3
VIIth SEMESTER
1. Subject Code: EC401 Course Title: B.Tech Project-I

2. Contact Hours: L:0 T:0 P:0
4. Relative Weight: CWS: 0 PRS: 0 MTE: 0 ETE: 0 PRE: 0
5. Credits: 4 6. Semester: VII 7. Subject Area: DCC
9. Objective: To familiarize the students to work in group and develop an independent understanding of
engineering and analysis of engineering systems. He should also be able to write and present the work
done during the course.
1. Subject Code: EC403 Course Title: Training Seminar

2. Contact Hours: L: 0 T:0 P:0
5. Credits: 2 6. Semester: VII 7. Subject Area: DCC
9. Objective: To familiarize the students to work in industry and working culture of the industrial system.
He should also be able to write and present the work done during the course.
DRAFT EC-31
1. Subject Code: EC – 405 Course Title: Microwave Engineering
5. Credits: 4
6. Semester: VII
9. Objective: To introduce fundamentals of microwave components.
Hours
1. Introduction, advantages and applications of Microwave Systems : Microwave 10
sub-bands, Scattering matrix :Reflection and Transmission coefficients .
Symmetry, reciprocity and power properties, zero property and unitary property.
2. Microwave components : Waveguide couplings, bends and twists, Directional 10
couplers, hybrid couplers, Matched load, Attenuators and phase shifters, E-
plane, H-plane and Hybrid Tees, Hybrid ring, Waveguide discontinuities,
Windows, Irises and Tuning screws, Detectors, wave meters; Isolators and
Circulators, tunable detector, slotted line carriage.
3. Microwave Tubes : Limitation, of conventional active devices at Microwave 10
frequency. Velocity modulation, Principle of operation, performance
characteristics and application of two cavity Klystron, Multi-cavity Klystron,
Reflex Klystron, TWT, Magnetron. Slow wave structures and their applications.
4. Microwave Semiconductor Devices : PIN diode, Tunnel diode, LSA diode, 12
varactor diode, Parametric Amplifier, Gunn Devices, IMPATT and TRAPATT,
their Principal of operation, characteristics and applications.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Liao, S.Y. / Microwave Devices & Circuits; PHI. 2003
2 Collin, R.E. Foundations for Microwave Engineering; TMH 2000
1. Subject Code: EC - 407 Course Title: Optical Communication

5. Credits: 4
6. Semester: VII
9. Objective: To introduce advanced concepts of Optical Communication
DRAFT EC-32
Hours
1. Type of Optical Fibers : Introduction to vector nature of light, propagation of light, 6
propagation of light in a cylindrical dielectric rod, Ray model, wave model.
Different types of optical fibers, Modal analysis of a step index fiber. Signal
degradation on optical fiber due to dispersion and attenuation.
2. Fabrication of fibers and measurement techniques like OTDR. Optical sources - 6
LEDs and Lasers, Requirements of Optical Sources.
3. Photo-detectors : PN, PIN, APD and RAPD photodetectors, detector 10
responsivity, noise, optical receivers. Optical link design, BER calculation,
quantum limit, Thermal noise limit, power penalties.
4. Optical switches : Coupled mode analysis of directional couplers, electro-optic 6
switches, Performance of Optical Receivers, SNR calculations.
5. Non-linear effects in fiber links : Concept of self-phase modulation, group velocity 8
dispersion and soltion based communication.
6. Optical amplifiers and Networks : EDFA, Raman amplifier, and WDM systems. 6
Hybrid optical amplifier, Optical amplifiers for next generation, WDM optical
communication networks, SDH, SONET, Review of High-Speed Mode-Locked
Quantum-Dot Lasers and Optical Amplifiers.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Fibre Optic communication, 5th Edition, by Gerd Keiser; McGraw-Hill. 2013
2. Optical communication systems by J.Gowar; Prentice Hall India, 1987

3. Integrated optics, by T. Tamir, Springer-Verlag 1975
4. Optical fibers for transmission, by J.E. Midwinter; John Wiley 1979
5. Optical fibres telecommunications, by S.E. Miller and A.G. Chynoweth, 1979
Academic Press
6. Nonlinear fibre optics by G.Agrawal, Academic Press, 2nd Ed. 1994
7. Fiber optic Communication Systems, by G. Agrawal; John Wiley and sons, New 1992
York
8. Fiber Optics Handbook for engineers and scientists, by F.C. Allard; McGraw Hill, 1990
New York
1. Subject Code: EC-402 Course Title: B.Tech project-II

2. Contact Hours: L:0 T:0 P:0
3. Examination Duration (Hrs.): Theory:0 Practical: 0
4. Relative Weight: CWS: 0 PRS: 0 MTE: 0 ETE:0 PRE: 0
5. Credits: 8
6. Semester: VIII
DRAFT EC-33
9. Objective: To familiarize the students to work in group and develop an independent understanding of
engineering and analysis of engineering systems. He should also be able to write and present the work
done during the course.
1. Subject Code: EC404 Course Title: Wireless Communication

5. Credits: 4
6. Semester: VIII
9. Objective:To familiarize the students with the concepts of basics of Wireless Communication.

Hours
History of Wireless Communication, Introduction to Mobile Communication
Systems, Generation of Wireless Networks, Evolution of Wireless Systems,
Introduction to Spectrum Allocation for various Wireless services: Methods for
Spectrum Allocation, Spectrum Allocations for existing systems, Current
1. 6
Wireless Systems: Cellular Telephone Systems, Cordless Phones, WLAN,
Wide Area Wireless Data Services, Broadband Wireless Access, Paging
Systems, Satellite Networks, Low Cost-Low Powered Radios: Bluetooth and
Zigbee.
Cellular Mobile Telephone Architecture Overview. Cellular System
Fundamentals: Cellular System Components, Operation of Cellular Systems,
Channel Assignment, Frequency Assignments, Frequency Reuse Channels,
Handover in Cellular Systems, Handoff Algorithms, Cellular Interferences,
2. 8
Antennas for Cellular Systems, Concept of Cell Splitting, Sectorization, Mobile
Traffic Calculation, Dynamic Resource Allocation: Scheduling, Dynamic
Channel Assignment, Power Control, Orthogonal Systems [TDMA/FDMA],
Non-orthogonal Systems [CDMA].
Cellular Systems: Narrowband Cellular Systems: GSM, Wideband Cellular
Systems: CDMA, OFDM- Pulse Shaping, Windowing, Spectral Efficiency,
Synchronization, Amplitude Limitation, Hybrid OFDM.
3. 6
Practical Cellular mobile systems—AMPS, D-AMPS, GSM system architecture
overview, CDMA: IS-95 & IS-136. Call Management and System Operation.
CDMA Based Cellular System.
Radio Wave Propagation, Transmit and Receive Signal Models, Free Space
Path Loss, Shadow Fading, Combined Path Loss and Shadowing, Cell
Coverage Area.
Capacity of Wireless Channels: Capacity in AWGN, Resources of AWGN
4. Channels, Capacity of Flat Fading Channels, Capacity of Frequency- Selective 6
Fading Channels.
Multiuser Systems, Multiuser Channels: The Uplink and Downlink, Multiple
Access: FDMA, TDMA, CDMA, SDMA, Random Access:-Pure Aloha, Slotted
Aloha, CSMA.
Multi Carrier Modulation: Data Transmission using Multiple Carriers, OFDM,
Challenges in Multicarrier Systems, MC-CDMA.
5. 8
Ad Hoc Wireless Networks: Data Networks, Home Networks, Device Networks,
Sensor Networks.
DRAFT EC-34
Point to Point Communication: Time Diversity, Antenna Diversity, Frequency
Diversity, Impact of Channel Uncertainty.
MIMO: Narrow Band MIMO Model, MIMO Channel Capacity, MIMO Diversity
Gain, Frequency –Selective MIMO Channels, Smart Antennas, MIMO Multiuser
Systems.
Broadcast Networks: Introduction to Broadcast Systems, DAB, HD Radio
Technology, DVB, DTH.
Cellular Networks:- Introduction to cellular networks, GSM System, GPRS,
EDGE Technology, CDMA- Based Digital Cellular Standards, WLL,
6. 8
UMTS/WCDMA-HSUPA & HSDPA, DECT, CorDECT.
Convergence in Networks:- 3G and beyond, LTE, IoT, Wi-Fi Standards, Wi-
MAX, UWB, PCS-Wireless Personal Communication Systems, Personal Mobile
Satellite Communication Systems.
Total 42

No. Publication/
Reprint
1. Mobile Cellular Telecommunications Systems by WCY Lee; McGraw Hill 1990
International Editions
2. Mobile Communications Design Fundamentals by WCY Lee; Prentice Hall 1993
3. CDMA: Principles of Spread Spectrum Communications by AJ Viterbi, Addison 1995
Wesley, New York
4. Wireless and personal Communication Systems by VK Garg and JE Wilkes; 1996
Prentice Hall
5. Mobile Radio Communications by Raymond Steele; IEEE Press, New York, 1992
6. Wireless Communication Principle and Practices by Rappaport, Pearson. 2002
7. Wireless Communication and Networking By Vijay K. Garg, Elsevier 2008
DRAFT EC-35
Departmental Electives
DRAFT EC-36
1. Subject Code: EC 305 Course Title: Semiconductor Device Electronics
5. Credits: 4
6. Semester: V
7. Subject Area: DEC
9. Objective: To develop basic semiconductor physics concepts for better understanding of current
and future devices so that their applications to electronic and optoelectronic circuits can
be appreciated.
Hours
1. Energy Bands and Charge Carriers in Semiconductors: Bonding Forces and 8
Energy Bands in Solid, Charge Carriers in Semiconductors, Carrier
Concentrations, Drift of Carriers in Electric and Magnetic Fields, Fermi Level
at Equilibrium
2. Excess Carriers in Semiconductors: Optical Absorption, Luminescence, 8
Carrier, Lifetime and Photo Conductivity, Diffusion of Carriers
3. Junctions: Fabrication of P-N Junctions, Equilibrium Condition, Forward and 10
Reverse Bias Junctions, Breakdown, Transient and AC Conditions, Metal
Semiconductor Junctions, Hetero-Junction Optoelectronic Devices:
Photodiodes, Light Emitting Diodes.
4. Field Effect Transistors: Transistor Operation, the Junction FET, the Metal 8
Semiconductor FET, the Metal insulator semiconductor FET, MOSFET.
5. Bipolar Junction Transistors: BJT Fabrication, BJT Operation, Minority Carrier 8
Distributions, Terminal Currents, Biasing, Amplification with BJT, Switching,
Frequency Limitation of Transistors, Hetero-Junction BJT .
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Solid State Electronic Devices by Streetman B.G. & Banerjee, Sanjay , 2006
Prentice Hall (India) / 5th Ed
2. Physics of Semiconductor Devices by Sze, S.M. ,Wiley Eastern Limited 2007
3. Microwave Semiconductor Devices and Their Circuit Applications by 1969

Watson, H.A. ,Tata McGraw-Hill.
4. Electronic Devices & Circuits by Bell David A. /Prentice Hall (India). 2009
5. Electronic Devices & Applications by Nair, B. Somanathan Prentice Hall 2004

(India)
6. Microwave Semiconductor Devices by Roy, Sitesh Kumar & Mitra, Monojit 2003
,Prentice Hall (India)
7. Electronic Devices & Circuits by Salivahanan, S. & Kumar, Suresh N. & 2008
Vallavraj , Tata McGraw-Hill.
DRAFT EC-37
8. Semiconductor Physics & Devices by Neamen, Donald A, Tata McGraw- 2002
Hill..
9. Semiconductor Devices Modeling & Technology by Das Gupta, N. , 2000

Prentice Hall (India)
10. Device Electronics for IC by Muller, Richard & Kamins, Theodone L ,John 1983
Wiley.
11. Advance Theory of Semiconductor Devices by Karl, Hess ,Prentice Hall 2000
(India)
1. Subject Code: EC – 307 Course Title: Antenna Design

2. Contact Hours: L: 3 T: 0/1 P: 2/0
5. Credits: 4
6. Semester: VII
9. Objective: To introduce fundamentals of Antenna Design
Hours
1. Antenna as a terminated line : Short dipole -Vector potential of short dipole, 10
Electric and magnetic field components, Far and near field components. Linear
dipole- Current distribution, Electric and magnetic field components. Radiated
power and antenna radiation resistance.
2. Radiation Pattern of Antenna : E-plane and H-plane pattern, Three dimensional 10
pattern. Power pattern. Classification of antenna based on patterns. Beam solid
angle of antenna. Antenna directivity, Antenna gain, Antenna efficiency,
Effective length and aperture of antenna. Beamwidth and bandwidth of antenna,
Antenna polarization.
3. Grounded and ungrounded antennas : Resonant and non-resonant antenna. 10
Antenna array- Broadside antenna array, End-fire antenna array, Increased
directivity end-fire antenna array. Pattern multiplication theorem
4. Folded dipole, Loop antenna, Horn antenna, Helical antenna, YAGI-UDA, 15
LPDA, Lens antenna, Parabolic reflector antenna. Corner reflector antenna,
Micro-strip antenna.
TOTAL 45
11. Suggested Books

Publication/
Reprint
1. Antennas: For All Applications - Kraus, John D&, Ronald J Mashefka - Tata 1989
McGraw Hill, 3rd Edition,
2. Antenna theory: Analysis and Design by Constantine A. Balanis, Wiley, 3 rd 2005
Edition,
3. Antennas and Wave Propagation - Prasad- K.D - Khanna Publications 1997
DRAFT EC-38
1. Subject Code: EC309 Course Title: Bio-Medical Electronics & Instrumentation
5. Credits: 4
6. Semester:V
9. Objective:To familiarize the students with the concepts of basics of Bio-Medical Electronics &
Instrumentation.
S. Contents Contact
No. Hours
Principles of biomedical instrumentation and techniques, Interfacing problems of
1. biomedical, electronic equipments with living systems. ECG, EEG, EMG 06
instruments for measuring bio signals.
Biomedical transducers. Bio-magnetic measurement and imaging. Cardiac output
2. measurement techniques. Diagnostic and therapeutic instruments, Prosthetic 08
devices such as pacemaker, hearing aid and myoelectric arm.
Functional electrical stimulation and algorithms for extremity control. Biotelemetry
3. of biological signals, biosensors. Neonatal monitoring. Special aspects such as 06
safety of medical electronic equipment.
Introduction to analog and digital computer simulation in biological sciences.
Simulation of normal and pathological states. Pattern identification and tissue and
4. 10
cell typing. Automated examination and interpretation of X-ray films of lungs and
hearts. Assembly of three- dimensional images.
Artificial intelligence, Robotics and expert systems in biomedical electronics and
medicines.
Overview of Patient Monitoring Systems, Arrhythmia and Ambulatory Monitoring
5. Instruments, Patient Safety, Digital Radiography, Nuclear Medical Imaging 12
Systems, Magnetic Resonance Imaging System, Ultrasonic Imaging Systems,
Thermal Imaging Systems, Pacemakers and Defibrillators, Automated Drug
Delivery Systems.
Total 42

No. Publication/
Reprint
1 Biomedical Instrumentation: Technology and Applications by R. S. Khandpur. 2003
Tata McGraw Hill Publishers.
2 Handbook Of Biomedical Instrumentation by Khandpur, R.S.; Tata McGraw Hill 2003
Publishers.
3 Biomedical Instrumentation and measurement by Cromewel, Wibell, Pfeiffer, 2006
2nd edition, PHI.
4 Medical Instrumentation: Theory and Design, 3rd Ed by John Webster; Wiley 2007
India.
DRAFT EC-39
1. Subject Code: EC 311 Course Title: Algorithms Design and Analysis
5. Credits: 4
6. Semester: VIII
9. Objective: To introduce various algorithm design and analysis fundamentals.
Hours
1. Introduction: Concept of algorithmic efficiency, run time analysis of algorithms, 6
Asymptotic Notations. Growth of Functions, Master's Theorem
2. Searching and Sorting: Structure of divide-and-conquer algorithms; examples: 6
binary search, quick sort, Stassen Multiplication; merge sort, heap sort and
Analysis of divide and conquer run time recurrence relations.
3. Greedy Method: Overview of the greedy paradigm examples of exact 10
optimization solution: minimum cost spanning tree, approximate solutions:
Knapsack problem, Kruskal’s algorithm and Prim’s algorithm for finding
Minimum cost Spanning Trees, Dijkstra’s and Bellman Fort Algorithm for finding
Single source shortest paths..
4. Dynamic programming: Principle of dynamic programming. Applications: Floyd- 6
Wars hall algorithm for all pair shortest paths. Matrix multiplication, Traveling
salesman Problem, longest Common sequence,
Back tracking: Overview, 8-queen problem, and Knapsack problem. Traveling
Salesman problem
5. Branch and bound: LC searching Bounding, FIFO branch and bound, LC branch 6
and bound application: 0/1 Knapsack problem,
6. Computational Complexity: Complexity measures, Polynomial Vs non- 8
polynomial time complexity; NP-hard and NP-complete classes, examples:
Circuit Satisfiablity, Vertex cover, Subset Sum problem, Randomized
Algorithms, String Matching, NP-Hard and NP-Completeness, Approximation
Algorithms, Sorting Network, Matrix Operations, Polynomials and FFT, Number
Theoretic Algorithms.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. T .H .Cormen, C .E .Leiserson, R .L .Rivest “Introduction to Algorithms”, PHI. 2009
2 E. Horowitz, S. Sahni, and S. Rajsekaran, “Fundamentals of Computer 2008
Algorithms,” Galgotia Publication
3 Sara Basse, A. V. Gelder, “ Computer Algorithms,” Addison Wesley 2002
DRAFT EC-40
1. Subject Code: EC 313 Course Title: Microprocessor and Interfacing
3. Examination Duration (ETE)(Hrs.): Theory 4Hrs Practical 2
5. Credits: 4
6. Semester: V
7. Subject Area: DEC 1
8. Pre-requisite: Basics of Digital Electronics
9. Objective: To introduce basic and pipeline architecture of microprocessors and assembly language
programming. It also focuses on interfacing different peripherals like USART, Priority Interrupt Controller,
Programmable Timers, Memory etc.
Hours
1. Introduction to microprocessor, history of computers, timing and control, 4
memory devices-semiconductor memory organization, category of memory,
8-bit microprocessor (8085): Architecture, Instruction set, Addressing mode,
assembly language programming
2. 16-bit microprocessor (8086): architecture, physical address, segmentation, 12
memory organization, bus cycle, addressing modes, assembly language
programming of 8086.
3. Data transfer scheme: introduction, types of transmission, 8257(DMA), 8
8255(PPI), serial data transfer (USART 8251), programmable priority
controller (8259).
4. Programmable interval timer/ counter (8253/8254): introduction , modes, 6
interfacing of 8253, application. ADC/DAC: introduction DAC methods, ADC
converters, Types of ADC, ADC IC ( 0808/0809) , DAC and ADC interfacing
and applications.
5. Alphanumeric displays, LCD, Graphic Displays, high power Devices. 4
Communication Bus protocols: RS 232,RS 485,SPI, Inter integrated circuits
interfacing I2C standard.
6. Introduction to 80186/80286, Advance microprocessor: introduction to 32-bit 8
and 64-bit microprocessor, power PC.
TOTAL 42
11. Suggested Books
Year of
Reprint
1. D.V. Hall : Microprocessor interfacing, TMH second edition 1986
2. The Intel Microprocessor 8086/8088. 80186, 80286, 80386 and 80486 2000
Architecture Programming and Interfacing Barry B Brey , PHI
3. Microprocessor Architecture, Programming and Applications with the 8085 2013
4. Y C Liu and G. A. Gibson: microcomputer systems : the 8086/ 8080A family 2012
architecture programming and design, PHI 2nd edition
5. John P. Hayes : digital system design and microprocessors, McGraw Hill 2004
publication
DRAFT EC-41
1. Subject Code: EC – 315 Course Title: Computer Communication Networks
5. Credits: 4
6. Semester: VII
9. Objective: To introduce advanced concepts of Computer Communication Networks
Hours
1. Introduction to computer networks : Layered architecture- OSI reference model, 6
TCP/IP architecture, circuit switching networks, Data link layer- ARQ protocols,
framing, point –to-point protocol, HDLC data link control
2. Medium Access Control – ALOHA. Slotted ALOHA, CSMA, CSMA-CD, polling, 6
token passing ring, reservation, channelization. LANs- Ethernet, token ring, LAN
Bridges & Ethernet switches.
3. Network Layer: ARP and RARP, Routing algorithms and protocols, Congestion 10
control algorithm, Router Operation, Internet Routing Protocols, IPv6 (an
overview). Transport Layer: UDP, TCP (Flow Control, Error Control, Connection
Establishment)
4. Session layer & Application layer: DNS, SNMP, Electronic Mail, WWW, ISDN, 6
Frame Relay, ATM
5. Network Security: Firewalls (Application and packet filtering), Cryptographic 8
algorithms –DES, AES, RSA
6. Introduction to Adhoc Networks : Routing Protocols- AODV, DSR, Advances in 6
computer communication. Introduction to wireless sensor networks, An analysis
of coverage prediction of sensor networks in various fading environments such
as Rayleigh, Rician and Nakagami-m. A survey on coverage and connectivity, a
discussion on the application of wireless sensor networks.
TOTAL 42
11. Suggested Books

publication/
Reprint
1. Computer Communication Networks” by W. Stallings; PHI 1999
2 Communication Networks: Fundamental Concepts and key Architectures” by 2007
Alberto Leon Garcia, Indra Widjaja; TMH
3 TCP/IP Protocol Suite”, 2nd Ed., by B. A. Forouzan; TMH. 2004
4 Computer Networks”, 3rd Ed., by A. S. Tannenbaum; PHI 1999
1. Subject Code: EC 317 Course Title: Operating Systems

DRAFT EC-42
5. Credits: 4
6. Semester: V
9. Objective: To introduce fundamentals of operating systems
Hours
1. Introduction: Operating system and function, Evolution of operating system, 4
Batch, Interactive, Time Sharing and Real Time System, System protection.
Operating System Structure: System Components, System structure, Operating
System Services
2. Concurrent Processes: Process concept, Principle of Concurrency, Producer 10
Consumer Problem, Critical Section problem, Semaphores, Classical problems
in Concurrency, Inter Process Communication, Process Generation, Process
Scheduling.
CPU Scheduling: Scheduling Concept, Performance Criteria Scheduling
Algorithm, Evolution, Multiprocessor Scheduling. .
3. Deadlock: System Model, Deadlock Characterization, Prevention, Avoidance 10
and Detection, Recovery from deadlock combined approach.
4. Memory Management: Base machine, Resident monitor, Multiprogramming 10
with fixed partition, Multiprogramming with variable partition, Multiple base
register, Paging, Segmentation, Virtual memory concept, Demand paging,
Performance, Paged replaced algorithm, Allocation of frames, Thrashing,
Cache memory, Organization, Impact on performance.
5. I/O Management & Disk Scheduling: I/O devices and organization of I/O 4
function, I/O Buffering, DISK I/O, and Operating System Design Issues.
File System: File Concept, File Organization and Access Mechanism, File
Directories, File Sharing, Implementation Issues
6. Latest Research and Case Studies: Windows, Linux and UNIX, GPU- 4
Accelerated Solutions to Optimal Power Flow Problems, CMOS Startup Charge
Pump With Body Bias and Backward Control for Energy Harvesting Step-Up
Converter
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Silberschwatz, “Operating System Concepts”, Willey . 2012
2 Haldar and Aravind, “Operating Systems”, Pearson 2010
3. Tannenbaum, “Operating system design and implementation”, PHI. 2013
DRAFT EC-43
1. Subject Code: EC 319 Course Title: CMOS Analog IC Design
5. Credits: 4
6. Semester: V
9. Objective: To lay good foundation on the design and analysis of CMOS analog ICs. To study large signal
model of MOS transistor and second order effects. Designing of analog sub circuits, two op-amp circuits,
voltage reference circuits and ADCs, DACs.
Hours
1. Large Signal Model of MOS Transistor: I-V Characteristics, Early Effect, 5
Channel Length Modulation, Back Gate Effect and other Second-Order Effects.
Passive Components: Properties of Resistors and Capacitors and Matching
Considerations .
2. Analog Sub-circuits: Basic MOS Amplifiers, Differential Pairs, Current Sources, 9
MOS Switches, and Basic Sample/Hold Circuit .
3. Basic Two-Stage Op-Amp Design: NMOS and CMOS architectures, DC 10
Design, Frequency Compensation, Slew Rate, Power Supply Rejection, Offset
Voltage calculation and Noise considerations .
4. Voltage References: Basic Design and Evaluation of Band Gap Reference, and 8
CMOS Band Gap References .
MOS Voltage Comparators: Various Configurations and Offset Cancellation
Techniques .
5. Digital-to-Analog and analog to digital converters Current scaling DAC, Voltage 10
scaling DAC charge scaling DAC, Extending resolution of parallel DAC, similar
scaled DACs
High speed ADCS, parallel or flash ADCS, interpolating ADCS, folding ADCS,
Multibit pipeline ADCS, delta sigma modular, Decimators filters.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Design of Analog CMOS Integrated Circuits” by Behzad Razavi; Tata McGraw- 2000
Hill
2. CMOS analog Circuit Design by Allen Holberg, Oxford University Press 1987
3. Analog VLSI Signal and Information Processing by Mohammed Ismail Terri 1984
Fiez, McGraw Hill International Editions.
4. Analog MOS Integrated Circuits for Signal Processing by Roubik Gregorian 1986
and Gabor C. Temes, Wiley series on filters
5. Analysis and Design of Analog Integrated Circuits, Fourth Edition by Gray 2009
Hurst Lewis Meyer, Wiley
DRAFT EC-44
1. Subject Code: EC 321 Course Title: IC Technology
5. Credits: 4
6. Semester: V
9. Objective: To provide an understanding of the manufacturing methods and their underlying scientific
principles in the context of technologies used for VLSI chip fabrication.
Hours
1. Crystal Growth, Wafer Preparation: Introduction & Historical Perspective, Clean 6
room concept – Growth of single crystal Si, surface contamination, Chemical
Mechanical Polishing, wafer preparation, DI water, RCA and Chemical Cleaning.
Processing considerations: Chemical cleaning, getting the thermal Stress factors
etc.
2. Epitaxy and Oxidation: Vapor Phase Epitaxy - Molecular Beam Epitaxy - 6
Silicon on Insulators – Epitaxial Evaluation – Growth Mechanism and Kinetics –
Thin Oxides – Oxidation Techniques and Systems – Oxide Properties.
3. Lithography and Relative Plasma Etching: Optical Lithography – Electron 9
Lithography – X-Ray Lithography - Ion Lithography Plasma - Properties –
Feature Size - Control and Anisotropic Etch Mechanism – Relative Plasma
Etching Techniques and Equipment.
4. Deposition , Diffusion, Lon Implementation And Metallization: Deposition 9
Processes – Polysilicon – Plasma Assisted Deposition – Models of Diffusion in
Solids – Fick’s One Dimensional Diffusion Equation – Atomic Diffusion
Mechanism – Measurement Techniques – Range Theory – Implantation
Equipment. Annealing Shallow Junction – High Energy Implantation – Physical
Vapor Deposition – Patterning.
5. VLSI Process Integration, Analytical, Assembly Techniques And Packaging of 12
VLSI Devices: NMOS IC Technology – CMOS IC Technology – MOS Memory
IC Technology – Bipolar IC Technology – IC Fabrication.
Analytical Beams – Beams Specimen Interaction – Chemical Methods –

Package Types baking Design Considerations – VLSI Assembly Technology –
Package Fabrication Technology.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. VLSI Technology by S. M. Sze, McGraw-Hill, 2nd edition, 1988
2 Basic VLSI design by Douglas A Pucknell and Kamaran Eshragian, 3rd edition, 1994
PHI
3. Modern VLSI design by Wayne wolf, , 2 nd edition, Prentice Hall 1998
DRAFT EC-45
1. Subject Code: EC 323 Course Title: Control Systems
5. Credits: 4
6. Semester: V
9. Objective: To introduce advanced concepts of analog circuit analysis and design
Hours
1. Introduction to Control System: Linear, Non Linear, Time Varying and Linear 6
Time Invariant System, Mathematical Modelling of Physical Systems,
Differential Equations of Physical Systems, Transfer Functions, Block Diagram
Algebra and Signal Flow Graphs. Feedback and Non feedback Systems.
Reduction of Parameter Variations by use of Feedback Control Over System
Dynamics. Feedback Control of Effects of Disturbance.
2. Control Systems and Components DC and AC Servomotors, Synchro Error 6
Detector, Tacho Generator and, Stepper Motors etc.
3. Time Response Analysis: Standard Test Signals, Time Response of First-order 10
Systems, Time Response of Second-Order Systems, Steady-State Error and
Error Constants, Effect of Adding a Pole/ Zero to a System, P, PI and PID
Control Action and Their Effect, Design Specifications of Second-Order
Systems and Performance Indices. The Concept of Stability, Necessary
Conditions for Stability, Hurwitz Stability Criterion, Routh Stability Criterion and
relative Stability Analysis. The Root Locus Concept, Construction of Root
Loci, Root Contours, Systems with Transportation Lag, Sensitivity of the
Roots of the Characteristic equation, MATLAB: Analysis and Design of Control
Systems
4. Frequency Response Analysis: Correlation Between Time and Frequency 6
Response, Polar Plots, Nyquist plots Bode Plots. Stability in Frequency
Domain: Mathematical Preliminaries, Nyquist Stability Criterion, Calculation of
Gain Margin and Phase Margin in Nyquist Plot and Bode Plot, Assessment of
Relative Stability Using Nyquist Criterion and Closed-Loop Frequency
Response
5. Compensator and Controller Design: Design of Lag, Lead, Lead Lag, Feedback 8
compensator The Design Problem, Preliminary Considerations of Classical
Design, Realization of Basic Compensators, Cascade Compensation in Time
Domain Cascade Compensation in Frequency Domain, Tuning of PID
Controllers. MATLAB based Frequency domain analysis of control system
6. Control Systems Analysis in State Space: State-Space Representations of 6
Transfer-Function Systems, Solving the Time-Invariant State Equation,
Controllability, Observability, Pole Placement, Design of Servo Systems, State
Observers, Design of Regulator Systems with Observers, Design of Control
Systems with Observers, Quadratic Optimal Regulator Systems, Robust
Control Systems.
TOTAL 42
DRAFT EC-46
11. Suggested Books
Publication/
Reprint
1. Modern Control Engineering Fifth Edition Katsuhiko Ogata Prentice 2005
Hall
2. Automatic Control Systems : Benjamin C. Kuo 2007
3. Control System Engineering: I J Nagrath , M Gopal 2008
4. Linear control Systems: B S Manke 2005
DRAFT EC-47
1. Subject Code: EC308 Course Title: Analog Filter Design
5. Credits: 4
6. Semester: VI
9. Objective: The emphasis of this course is on fundamental principles behind the various techniques of
analog filter design for signal processing.

Hours
1. Frequency response of bilinear and second order transfer functions, Design 10
parameters, Active realizations: SAB,MAB, Effect of A(s), RC-CR
Transformation, Sensitivity Analysis.
2. Filter approximation Functions: Butterworth, Chebyshev, Pole locations, Filter 8
specifications, Comparison of maximally flat and equal ripple response
Frequency Transformation: Low pass to High pass, Low pass to band pass,
Low pass to band elimination.
3. Ladder simulation by element replacement, GIC and optimal design, 10
Realization of simple ladders, Gorski Popiel embedding technique, Bruton’s
FDNR technique, Operational Simulation of ladder.
4. Switch capacitor filter, Log domain filters. 6
5. Current Mode Active block based Filters: Circuit structure and analysis of 8
operational trans -impedance Amplifier (OTIA) and various generations of
current Conveyers, MOSFET-C Filters and techniques of non-linearity
cancellation in MOS circuit.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. 1. Rolf Schaumann and Mac E. Van Valkenberg, Design of Analog Filters,
Oxford Indian Edition, 2008, CRC, 2ndEditionPrenticehall International (ISBN: 2008
0849337739)
2 G. Daryanani, Principles of active network synthesis and design Wiley
2003
3. G. Ferri, N. C. Guerrini, Low-Voltage Low-Power CMOS Current Conveyors.
Kluwer Academic Publishers 2003
DRAFT EC-48
1. Subject Code: EC-310 Course Title: Testing and Diagnosis of Digital Systems
5. Credits: 4
6. Semester: VI
9. Objective: To introduce fundamentals Testing and Diagnosis of Digital Systems
Hours
1. Faults in digital circuits: Fault modelling, fault detection, redundancy, 8
equivalence, fault location, fault dominance. Stuck at faults, bridging faults, stuck
open faults, Transient faults, Permanent faults.
2. Testing of Combinational circuits: Test generation for combinational logic circuits: 6
Path sensitization, Boolean difference method etc CAD scheme for
combinational digital circuits: D- algorithm, PODEM, FAN algorithm
3. Testing of sequential circuits: State identification experiments, checking 7
experiments and machine identification. Fault tolerance techniques for
sequential circuits, Easily Testable Design and Diagnosis of Sequential Machine
4. Self-checking and fail safe logic: Checking circuits &self-checking, Totally self- 8
checking: m/n code self-checkers and equality self-checkers. Self-checking in
PLAs. Self-stabilizing fault tolerant circuits Fail safe design.
5. Design for testability: controllability and observability. 7
Random test generation, transition count testing, signature analysis, syndrome
testable design, RMC, Level sensitive scans design.
BIST: LSSD on-chip self-test, BILBO, BIDCO.
6. Fault detection in RAM and Microprocessor. 6
TOTAL 42
11. Suggested Books
Publication/
Reprint
1 Fault Tolerant and Testable Hardware Design”, P. K. Lala: prentice hall 1985
International editions
2 “Digital Circuit and Logic Design”, S. C. Lee, (PHI). 2007
3 “Digital System Testing and Testable Design” by M. Abramovici, M. A. Breuer, 1994

A. D. Friedman, Wiley
4 “Checking Experiments in Sequential Machine” by A. Bhattacharyya Wiley 1989
Easton
DRAFT EC-49
1. Subject Code: EC – 312 Course Title: Software Defined Radio and Cognitive Radio
3. Examination Duration (ETE)(Hrs.): Theory 3 Hrs Practical 0
5. Credits: 4
6. Semester: VI
9. Objective: To introduce fundamentals of Software Defined Radio and Cognitive Radio
Hours
1. Introduction to Cognitive Radio : Hardware and software architectures of cognitive 6
radio, Smart Antennas used in Cognitive Radio; Spectrum Management;
Opportunities in Spectrum Access, Policy Challenges for Cognitive Radios.
2. Technologies in Cognitive Radio : Radio Flexibility and Capability, Comparison of 6
Radio Capabilities and Properties, Available Technologies for Cognitive Radios Radio
Frequency Translation for Software Defined Radio Receiver Design Considerations,
Transmitter Design Considerations, Candidate Architectures for SDR.
3. Spectrum awareness, sensing and identification : Primary Signal Detection, From 9
Detecting Primary Signals to Detecting Spectrum Opportunities, Fundamental Trade-
offs: Performance versus Constraint, Fundamental Trade-offs: Sensing Accuracy
versus Sensing Spectrum Access and sharing Unlicensed Spectrum Sharing,
Licensed Spectrum Sharing, Secondary Spectrum Access, Non-Real-Time SSA,
Real-Time SSA.
4. Transmission Techniques : Wireless Transmission for Dynamic Spectrum Access, 9
Non-contiguous Orthogonal Frequency Division Multiplexing, NC-OFDM-Based
Cognitive Radio: Challenges and Solutions, Overhead Interference Avoidance
Problem, Spectral Footprint Minimization, Spectrum Usage Reporting, Potential
Interference Analysis, Link Rendezvous, Distributed Sensing and Operation Channel
Awareness and Multiple Signals in Space.
5. Reconfiguration, adaptation, and optimization : Adaptation Engine Operating 12
Parameters, Parameter Relationships, Cognitive Adaptation Engines Cognitive radio
network architectures : Overview of Architectures Topology-Aware CRN Architectures
Publish-Subscribe CRN Architecture Introduction to User cooperative
communications Relay Channels User Cooperation in Wireless Networks Multi hop
Relay Channel Cross-layer optimization for multi-hop cognitive radio networks
Mathematical Models at Multiple Layers A Case Study: The Throughput Maximization
Problem Numerical Results for the Throughput Maximization.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Cognitive Radio Communications and Networks Principles and Practice 2010
Alexander M. Wyglinski, Maziar Nekovee, Y. Thomas Hou, Published by
Elsevier
2. Cognitive Radio, Software Defined Radio, and Adaptive Wireless Systems, 2007
Edited by HÜSEYIN ARSLAN, University of South Florida, Tampa, FL, USA,
Published by Springer
3. Cognitive Radio Technology, Bruce A. Fette Published by Elsevier 2009
DRAFT EC-50
1. Subject Code: EC – 314 Course Title: RF Design
5. Credits: 4
6. Semester: VI
9. Objective: To introduce fundamentals of RF Design.
Hours
1. Introduction: Importance of radiofrequency design, RF/microwave versus DC 8
or low AC component: High frequency resistors, capacitors and inductors.
Impedance signals, Dimensions and units, frequency spectrum. RF
behaviour of passive transformers, RF impedance matching. Graphical
representation (Smith Chart): Impedance transformation for general load,
Standing wave ratio, Special transformation conditions. (ZY
Chart)Admittance Transformations: Parametric admittance equation,
Additional graphical displays. Parallel and series Connections of R, L, C.
2. RF Filter Design: Filter types and parameters, Low pass filter, High pass filter, 10
Bandpass and Band stop filter, Insertion Loss. Special Filter Realizations:
Butterworth type filter, Chebyshev type filters, Demoralization of standard low
pass design. Filter Implementation: Unit Elements, Kuroda’s Identities and
Examples of Microstrip Filter Design. Coupled Filters: Odd and Even Mode
Excitation, Bandpass Filter Design, Cascading bandpass filter elements,
Design examples.
3. Single and multiport networks: Basic Definitions, Interconnecting Networks. 10
Scattering Parameters: Scattering Parameters: Definition, Meaning, Chain
Scattering Matrix, and Conversion between S- and Z-parameters, Signal
Flow Chart Modelling. Stability and Gain Considerations - Transducer Power
Gain, Additional Power Relations-Stability Considerations: Stability Circles,
Unconditional Stability, and Stabilization Methods-Unilateral and Bilateral
Design for Constant Gain- Noise Figure Circles- Constant VSWR Circles.
4. Amplifiers design and Oscillators Design: single stage transistor amplifier 8
design, Design for specified gain, broadband transistor amplifier design, One
port negative resistance oscillators, Design procedure of Transistor
Oscillators, dielectric resonator oscillator.
5. RF/Microwave frequency conversion: Mixers Types, SSB versus DSB 6
mixers, conversion loss, Noise figure.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Mathew M. Radmanesh, “Radio Frequency & Microwave Electronics”, 2002
Pearson Education Asia, Second Edition,
DRAFT EC-51
2. Reinhold Ludwig and Powel Bretchko,” RF Circuit Design – Theory and 2000
Applications”, Pearson Education Asia, First Edition.
3. David M. Pozar, “Microwave Engineering, 4th Edition” Wiley 2011
4. Devendra K. Misra ,”Radio Frequency and Microwave Communication 2004
Circuits – Analysis and Design “John Wiley & Sons, Inc.
5. Ulrich L. Rohde and David P. New Kirk, “RF / Microwave Circuit Design”, 2000
John Wiley & Sons USA,
6. Joseph. J. Carr, “Secrets of RF Circuit Design”, McGraw Hill Publishers, 2004
Third Edition.
1. Subject Code: EC 316 Course Title: Wireless Sensor Networks

5. Credits: 4
6. Semester: VI
8. Pre-requisite: Basics of Communication and Networking
9. Objective: To introduce basic concepts of Wireless Sensor Networks
Hours
1. Adhoc Networks: Introduction. Routing protocols: proactive and reactive 10
methods, backbone and position based, and power efficient routing.
2. Sensor Networks: Introduction and applications. Design issues and architecture. 08
3. Sensor deployment: Issues and challenges, Self organization, Localization. 08
4. Data Fusion: Tree construction algorithms and analysis, Asymptotic capacity, - 08
Lifetime optimization formulations.
5. Routing protocols: data centric, hierarchical, location based, energy efficient 4
routing etc.
6. Querying, data collection and processing. 4
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Handbook of Algorithms for Wireless Networking and Mobile Computing 2006
by Azzedine Boukerche , Chapman & Hall/CRC.
2 Handbook of Sensor Networks: Compact Wireless and Wired sensing 2005
systems by Mohammad Ilyas and Imad Mahgoub , CRC Press.
3. Wireless Sensor Network Designs by Anna Hac, John Wiley & Sons Ltd. 2003
4. Wireless Sensor Networks: A systems perspective by Nirupama Bulusu 2005
and Sanjay Jha ,Artech House.
5. Wireless Sensor Networks : Architecture and Protocols by Jr., Edgar H. 2003
Callaway; Auerbach .
6. Wireless Sensor Networks by C.S. Raghavendra, Krishna M. Sivalingam 2005
and Taieb Znati, Springer
DRAFT EC-52
1. Subject Code: EC318 Course Title: RF Circuits in CMOS Technology
5. Credits: 4
6. Semester: VI
9. Objective: The objective of this course is to introduce the concepts of design and analysis of RF circuits
in CMOS technology.

Hours
1. Introduction, Passive RLC Networks and IC Components: Parallel RLC tank, Q 6
, Series RLC networks, matching Pi match, T match. Passive IC Components:
Interconnects and skin Effect, Resistors, capacitors Inductors BJT and
MOSFET behavior at RF frequencies, modeling of the transistors and SPICE
model, Noise performance and limitations of devices, integrated parasitic
elements at high frequencies
2. High Frequency Amplifier Design Bandwidth estimation using open-circuit time 6
constants Bandwidth estimation using short-circuit time constants Rise-time,
delay and bandwidth Zeros to enhance bandwidth Shunt-series amplifiers,
tuned amplifiers Cascaded amplifiers. Overview of RF Filter design
3. LNA and Mixer Design Intrinsic MOS noise parameters, Power match versus 9
noise match Large signal performance, Multiplier based mixers, Subsampling
mixers
4. RF Power Amplifiers Class A, AB, B, C amplifiers, Class D, E, F amplifiers RF 9
Power amplifier.
5. Oscillators- Basic topologies VCO and definition of phase noise, Noise power 12
and trade off. Radio frequency Synthesizers- PLLS, Various RF synthesizer
architectures and frequency dividers, Design issues in integrated RF filters.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. The Design of CMOS Radio-Frequency Integrated Circuits by Thomas H. Lee.
Cambridge University Press 2004
2. RF Microelectronics by Behzad Razavi. Prentice Hall, 1997.ia htnptel.iitm.ac.in
Reference Books: 1997
3. RF Microelectronics by B. Razavi ,PHI 1998
4. CMOS Circuit Design, layout and Simulation by R. Jacob Baker, H.W. Li, D.E. 1998
Boyce , PHI
5. Mixed Analog and Digital Devices and Technology by Y.P. Tsividis , TMH 1996
DRAFT EC-53
1. Subject Code: EC 320 Course Title: Soft Computing
5. Credits: 4
6. Semester: VI
9. Objective: To introduce fundamentals of passive and active filter design for signal processing
Hours
1. Introduction of soft computing, soft computing vs. hard computing, 12
various types of soft computing techniques, applications of soft computing.
Artificial Intelligence : Introduction, Various types of production systems,
characteristics of production systems, breadth first search, depth first search
techniques, other Search Techniques like hill Climbing, Best first Search, A*
algorithm, AO* Algorithms and various types of control strategies. Knowledge
representation issues, Prepositional and predicate logic, monotonic and non-
monotonic reasoning, forward Reasoning, backward reasoning
2. Neural Network : Structure and Function of a single neuron: Biological neuron, 10
artificial neuron, definition of ANN, Taxonomy of neural net, Difference between
ANN and human brain, characteristics and applications of ANN, single layer
network, Perceptron training algorithm.
3. Fuzzy Logic: Fuzzy set theory, Fuzzy set versus crisp set, Crisp relation & fuzzy 10
relations ,Fuzzy systems: crisp logic, fuzzy logic, introduction & features of
membership functions, Fuzzy rule base system : fuzzy propositions, formation,
decomposition & aggregation of fuzzy rules, fuzzy reasoning, fuzzy inference
systems, fuzzy decision making & Applications of fuzzy logic.
4. Genetic algorithm : Fundamentals, basic concepts, working principle, encoding,
fitness function, reproduction, Genetic modeling: Inheritance operator, cross
over, inversion &deletion, mutation operator, Bitwise operator, Generational
Cycle, Convergence of GA, Applications & advances in GA, Differences & 10
similarities between GA & other traditional method.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. S. Rajasekaran and G.A.Vijaylakshmi Pai.. Neural Networks Fuzzy Logic, and 2004
Genetic Algorithms, Prentice Hall of India.
2 K.H.Lee.. First Course on Fuzzy Theory and Applications, Springer-Verlag. 2004
3. J. Yen and R. Langari.. Fuzzy Logic, Intelligence, Control and Information, 1999
Pearson Education.
DRAFT EC-54
1. Subject Code: EC 322 Course Title: Green Technologies
5. Credits: 4
6. Semester: III
9. Objective: To introduce and discuss the utilization and application of green technology around the
world.
Hours
1. Renewable Energy Resources & Systems: Current energy requirements, growth 10
in future energy requirements, Review of conventional energy resources- Coal,
gas and oil reserves and resources, Tar sands and Oil Shale, Nuclear energy
Option Solar Energy, Wind Energy, Ocean Energy and Hydropower.
2. Smart Grid and ICT role in its revolution climate change, conventional electricity 8
grid. Smart grid: building block, network topologies, communication systems,
smart grid applications.
3. Green Communication for carbon emission reduction: Introduction, Network 8
architectures and technologies to reduce carbon emission, networks and
protocols, integrated optical-wireless access, data centers, test beds, Carbon
standards for communication technologies.
4. Green RAN framework, introduction, challenges, architecture and advantages of 8
CRANGreen AdHoc and sensor network : Introduction, energy harvesting and
conservation techniques, energy synchronization techniques.
5. Green wireless communication under QoS constraints :Introduction, Variable 8
rate/ variable power, Variable rate/ fixed power and fixed rate/fixed power
transmissions: channel model, energy efficiency in low power regime, energy
efficiency in wide band regime, Green wireless access network
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Principles of Solar Engineering by D. Y. Goswami, F. Kreith and J. F. Kreider, 2010
Taylor and Francis, Philadelphi
2. Green Communications: Theoretical Fundamental Algorithms and Applications 2012
by Jinsong Wu, Sundeep Rangan, Honggang Zhang. CRC Press
1. Subject Code: EC324 Course Title: Nano Electronics

5. Credits: 4
6. Semester: VI
DRAFT EC-55
9. Objective: To learn and understand basic and advance concepts of Nano Electronics.

Hours
1. Introduction to Nano electronics, Shrink Down Approaches, CMOS Scaling, the 6
Nanoscale MOSFET, FINFETs, Vertical MOSFETs, Strained Silicon Technology,
Limits to Scaling, System Integration Limits (Interconnect Issues, etc.)
2. Resonant Tunneling Diodes, Resonant Tunneling Transistors, MOBILEs 6
(Monostable-Bistable Transition Logic Elements),Single Electron Transistors, New
Storage Devices, SRAM,DRAM, MRAM (Magneto-resistive RAM), PCRAM (Phase
change RAM), AFM based Mass Storage (the Millipede Concept), Optoelectronic
and Spintronic Devices.
3. Molecular Electronics (involving single molecules as electronic devices), Transport 9
in Molecular Structures, Molecular Systems as Alternatives to Conventional
Electronics, Molecular Interconnects. MEMS, FBARs (Film Bulk Acoustic
Resonators), Cantilevers.
4. Carbon Nanotube Electronics: Band structure &Transport, Devices (CNTFETs, CNT 9
Logic Gates, CNT RTL Circuits, CNT SET,CNT RAM, CNT Field Emission Devices),
Carbon Nano tube Interconnects, CNT Heat Sink, Applications. Graphene Based
Electronics: Band structure & Transport, Devices (GNR FETs),Applications.
Nanowire FETs, Nanowire Logic Gates.
5. Nano sensors: Biological and Chemical; Electronic Sensor Arrays, CMOS 3-D Time- 12
of –Flight Image Sensor, Nano-biomimetic Technologies: Electronic Skin, Electronic
Eye, Electronic Nose (KAMINA), Electronic Tongue; Touchscreens, Robot Tactile
Sensors, Fingerprint Sensors, Liquid Crystal Displays, Organic Electronic Devices:
Organic Light Emitting Diodes, Organic Solar Cells, Organic Thin Film Transistors;
Field Emission & Plasma Displays, Electronic Paper.
Neuro-electronic Systems: Iono-electronic Interface, Neuron-Silicon Circuits, Brain-
Silicon chips, Neuro-electronic Processors, Neuro-prosthetics, Electrical Dynamics
of the Neuron-Chip Interface on a Nanoscopic Level, Hybrid Systems made of
Neuronal Nets and Electronic Devices on a Microscopic Level, Ionoelectronic
Devices, Nerve-based Ionic Processors.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Nano electronics and Information Technology Advanced Electronic Materials and 2012
Novel Devices) by Rainer Waser,Wiley-VCH
2. Nanoelectronics (Principles and Devices, Second Edition)byMircea Dragoman 2006
(Artech House).
3. Silicon Nanoelectronics by ShunriOda and David K. Ferry,Taylor& Francis
2002
4. Molecular Nano electronics by Mark A. Reed and TakheeLee, American 2003
Scientific Publishers
5. Nanoscale Transistors (Device Physics, Modeling &Simulation) by Mark S. 2000
Lundstrom and Jing Guo ,Springer
DRAFT EC-56
6. Fundamentals of Nano electronics by George W. Hanson (Pearson) , Research 2010
Papers
1. Subject Code: EC326 Course Title: Data Convertors

5. Credits: 4
6. Semester: VII
9. Objective:To provide a thorough background of data converter systems and circuits, discuss the real
world applications, IC design challenges and prepare students for other areas of analog and digital IC
design.
Hours
1. Sample and hold circuits: Sampling switches, Conventional open loop and closed 8
loop sample and hold architecture, Open loop architecture with miller
compensation, multiplexed input architectures, recycling architecture switched
capacitor architecture.
2. Switch capacitor circuits and comparators: Switched-capacitor amplifiers, switched 8
capacitor integrator, switched capacitor common mode feedback. Single stage
amplifier as comparator, cascaded amplifier stages as comparator, latched
comparators.
3. Digital to analog conversion: Performance metrics, reference multiplication and 9
division, switching and logic functions in AC, Resistor ladder DAC architecture,
current steering DAC architecture.
4. Analog to digital conversion: Performance metric, Flash architecture, Pipelined 9
Architecture, Successive approximation architecture, Time interleaved architecture.
5. Precision techniques: Comparator offset cancellation, Op-Amp offset cancellation, 8
Calibration techniques, range overlap and digital correction.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Principles of data conversion System Design by Behzad Razavi, IEEE press 1995
2. Data Converters by Franco Maloberti, Springer 2007
3. CMOS Integrated Analog-to-Digital and Digital-to-Analog Converters, by Rudy 2003
Van de Plassche, Kluwer Academic Publishers, Boston
1. Subject Code: EC 328 Course Title: Speech Recognition

5. Credits: 4
6. Semester: VII
DRAFT EC-57
7. Subject Area: DEC 3, DEC 4
9. Objective: To introduce advanced concepts of speech signal processing
Hours
1. The Speech Production mechanism: Physiological and Mathematical Model, 8
Relating the physiological and mathematical model, Categorization of Speech
Sounds based on the source-system and the articulatory model.
2. Basic Speech Signal Processing Concepts:Discrete time speech signals, 10
relevant properties of the fast Fourier transform and Z-transform for
speech recognition, convolution, linear and non-linear filter banks,Spectral
estimation of speech using the Discrete Fourier transform,Pole-zero modeling of
speech and linear prediction (LP) analysis of speech, Homomorphic speech
signal de convolution, real and complex cepstrum, application of cepstral
analysis to speech signals.
3. The Speech Recognition Front End:Feature extraction for speech recognition, 10
Static and dynamic features for speech recognition, robustness issues,
discrimination in the feature space, feature selection, Mel frequency cepstral co-
efficients (MFCC), Linear prediction cepstral coefficients (LPCC), Perceptual
LPCC.
4. Distance measures for comparing speech patterns: Log spectral distance, 6
cepstral distances, weighted cepstral distances, distances for linear and warped
scales,Dynamic Time Warping for Isolated Word Recognition.
5. Statistical models for speech recognition: Vector quantization models and 8
applications in speaker recognition, Gaussian mixture modeling for speaker and
speech recognition,Discrete and Continuous Hidden Markov .
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Rabiner&Juang. Fundamentals of Speech Recognition Upper Saddle River, NJ: 1993
Prentice-Hall, 1993. ISBN: 0130151572.
1. Subject Code: EC 330 Course Title: Digital Image Processing

3. Examination Duration (ETE) (Hrs.): Theory 3 Practical 0
5. Credits: 4
6. Semester: VI
8. Pre-requisite: Signals and Systems
9. Objective: To introduce the fundamentals of visual information, representation of 2-D and 3-D
information, enhancement of information, retrieval of information, and various colour models.

Hours
DRAFT EC-58
1. Introduction to Image processing, fundamental steps in DIP, concept of visual 6
information, image formation model, image sampling and quantization, digital
image representation, spatial and gray level resolution, relationship between
pixels, application of image processing system.
2. Introduction to Multidimensional signals and systems, 2D-Signals, 2D systems, 8
classification of 2D system, 2D convolution, 2D Z-transform, Image Transform:
2D-DFT, discrete cosine, discrete sine, Haar, Walsh, Hadamard, Slant, KL, SVD,
Hough, Radon, Ridgelet.
3. Image enhancement; Spatial domain: linear transformation, image negative, grey 10
level shifting, non-linear transformation, logarithmic transformation, exponential
transformation, grey level slicing, bit plane slicing, image averaging, mask
processing, histogram manipulations, histogram thresholding, histogram
stretching, histogram equalization, noise removing filters, smoothing filters,
sharpening filters. Enhancement in Frequency Domain; ideal low pas filter,
Butterworth low pass filter, ideal high pass filters, Butterworth high pass filter,
band pass filter, Gaussian filters, Homomorphic filtering.
4. Image restoration: degradation model, noise models, restoration in presence of 6
noise, periodic noise removal in frequency domain, notch filters, inverse filtering,
Wiener filtering.
5. Introduction to Morphological Image Processing operations, dilation and erosion, 6
opening and closing, hit-or-miss transformation, boundary extraction, region
filling, extraction connected components, convex hull, thinning, thickening,
skeletons, pruning.
6. Introduction to various colour models: RGB, CMY, CMYK, HSI, HSV, and YCbCr. 6
Concept of image compression, Image Segmentation: detection of
discontinuities, edge linking and boundary detection, thresholding, region based
segmentation, use of motion in segmentation.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Digital Image Processing/ Gonzalez and Woods/ Pearson Education 2008/Third
Edition
2. Fundamentals of Digital Image Processing/ A.K. Jain/ PHI Indian
Edition
3. Digital Image Processing using MATLAB/ Gonzalez, Woods, and Eddins/ Mc Second/
Graw Hill 2013
4. Digital Image Processing/ K.R. Castleman/ Pearson 2014
5. Digital Image Processing Algorithms and Applications/I. Pitas/John Wiley 2002
6. Image Processing, Analysis, and Machine Vision/Milan Sonka, Vaclav Hlavac, 4th Edition
Roger Boyale/ Cengage Learning
1. Subject Code: EC - 332 Course Title: Information Theory and Coding

DRAFT EC-59
5. Credits: 4
6. Semester: VII
9. Objective: To introduce advanced concept of Information Theory and Coding

Hours
1. Information Theory: Introduction, Measure of information, Average information 12
content of symbols in long independent sequences, Average information content
of symbols in long dependent sequences. Mark-off statistical model for
information source, Entropy and information rate of mark-off source. Source
Coding: Encoding of the source output, Shannon’s encoding algorithm.
Communication Channels, Discrete communication channels, Continuous
channels.
2. Fundamental Limits on Performance: Source coding theorem, Huffman coding, 8
Discrete memory less Channels, Mutual information, Channel Capacity. Channel
coding theorem, Differential entropy and mutual information for continuous
ensembles, Channel capacity Theorem
3. Introduction to Error Control Coding: Introduction, Types of errors, examples, 8
Types of codes Linear Block Codes: Matrix description, Error detection and
correction, Standard arrays and table look up for decoding
4. Binary Cycle Codes, Algebraic structures of cyclic codes, Encoding using an (n- 6
k) bit shift register, Syndrome calculation. BCH codes.
5. RS codes, Golay codes, Shortened cyclic codes, Burst error correcting codes. 8
Burst and Random Error correcting codes. Convolution Codes, Time domain
approach. Transform domain approach
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Digital and analog communication systems, K. Sam Shanmugam, John Wiley, 1996
2. Digital communication, Simon Haykin, John Wiley. 2003
3. ITC and Cryptography, Ranjan Bose, TMH, II edition 2007
4. Digital Communications - Glover and Grant; Pearson Ed. 2nd Ed
DRAFT EC-60
1. Subject Code: EC-409 Course Title: Computer Vision
5. Credits: 4
6. Semester: VII
9. Objective: To introduce fundamentals of Computer Vision and algorithms for object detection ,
recognition and tracking application
Hours
1. Introduction to computer vision: Role of Artificial intelligence and image 5
processing in Computer Vision, Industrial Machine Vision applications, System
architecture. Visual Sensors: Camera sensors: RGB, IR, Kinect sensor, Camera
interfaces and video standards, Characteristics of camera sensors commercially
available cameras. Camera Calibration: Interior, exterior calibration and
rectification using Tsai’s Calibration method.
2. Basics of image processing – Pixel representations histograms ,transforms, 7
colour filters, noise removal,
Geometry: Math methods -linear algebra, vectors, rotations, Stereo – Epi-polar
geometry, correspondence, triangulation ,Disparity maps .
Basics of video processing – Background subtraction techniques – frame
differencing, Gaussian Mixture Modelling (GMM), Object localization and
processing:- Contours, edges, lines, skeletons.
3. Image representation: Local Wavelet basis (multiscale), Global Fourier 8
basis(Frequency), Adaptive basis (PCA and ICA) , Adaptive basis(discriminants)
Basics of Object detection – Template matching, Cascade classifiers.
4. Object Recognition : Object Modeling, Bayesian Classification, Feature Selection 6
and Boosting, Scene and Object Discrimination.
5. Motion and Tracking: Motion detection and tracking of point features, optical flow, 8
SURF, SIFT. Tracking- Kalman filter, Particle Filter, Comparison of deterministic
and probabilistic methods condensation, tracking humans, multi-frame
reconstruction under affine and perspective projection geometry.
6. Introduction to Computer Vision programming libraries: MATLAB, OpenCV. 8
Advantages/Disadvantages of each .
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Computer Vision: A Modern Approach (2nd Edition) 2nd Edition by David A. 2002
Forsyth (Author), Jean Ponce (Author)
2. Learning OpenCV: Computer Vision with the OpenCV Library Gary Bradski, 2008
Adrian Kaehler
1. Subject Code: EC 411 Course Title: Bio Medical Signal & Image Processing
3. Examination Duration (ETE )(Hrs.): Theory 3 Hrs Practical 2Hrs
5. Credits: 4
6. Semester: VII
DRAFT EC-61
9. Objective: To introduce fundamentals of biomedical signals and image processing
Hours
1. Different Types of Biomedical Signals:Biochemical signals,Bioelectric signals, 8
Biomechanical signals
ECG: Introduction, Characteristics, frequency sub-band and measuring methods.
EEG: Introduction, Characteristics, frequency sub-band and measuring methods.
Major modalities for medical imaging: ultrasound, X-ray, CT, MRI, fMRI, PET and
SPECT.
MRI: Introduction ,Basic MR Physics, MR Techniques, Artefacts, Advanced
Techniques, Instrumentation, MR Safety.
2. Biomedical Signal Processing: Fundamental Characteristics of Biomedical 8
Signals, Link Between Physiological Modeling and Biomedical Signal
Processing, Paradigm of Maximum Signal-System Integration, Characteristic
Aspects of Biomedical Signal Processing.
Parametric Models for the Analysis of Interactions in Biomedical Signals: Open-
Loop Identification, Closed-Loop Identification, Nonlinear Interactions and
Synchronization.
Interpretative Models in Biological Signal Processing: Mathematical Instruments
for Signal Processing, Descriptive Methods, The Black-Box Models,
Interpretative Models.
3. Artifacts in Biomedical Signals: Random noise,Structured noise, Physiological 6
interference,Signal dependent noise in biomedical signals,Poisson noise,Film
grain noise, Speckle noise. Transformation of signal dependent noise to signal
independent noise, Artifacts in ECG and EEG. Synchronized or Multi-frame
Averaging, Space domain local statistics based filters and Order Statistic Filters,
Frequency Domain Filters.
4. ECG and EEG denoising using following methods/Techniques: Hilbert-Huang 10
Transform, Cauchy distribution at sub band level,EMD,Parabolic Filter,Statistical
Adaptive Thresholding, Morphological Filtering, Undecimated Wavelet
Transform, Non-Local Means, signal-noise residue method,S-Transform.
5. Different steps of MR Image analysis and classification: Different types of 10

features, Advance feature enhancement methods, Advance feature extraction
methods, Advance feature reduction methods, Different MR image classifiers.
TOTAL 40
11.Suggested Books
Publication/
Reprint
1. Advance Methods of Biomedical Signal Processing by Sergio Cerutti and 2011
Carlo Marchesi, John Wiley & Sons, ISBN: 978-0-470-42214-4.
DRAFT EC-62
2. Biosignal and Biomedical image processing: MATLAB based applications by 2004
John L Semmlow, Marcel Dekker Inc, ISBN: 0-8247-4803-4.
3. Digital Image Processing using MATLAB By Rafael C. Gonzalez 2008

Richard E. Woods, Pearson Education International.
1. Subject Code: EC-413 Course Title: Power Electronics

5. Credits: 4
6. Semester: VII
7. Subject Area: DEC (DEC-5, DEC-6)
9. Objective: To introduce fundamentals Power electronics
Hours
1. Power Semiconductor Devices (PSD):Power Diodes, Enhancement of Reverse 8
blocking capacity, Reverse Recovery Silicon Controlled Rectifier (SCR)
Structure, v-I characteristics, turn ON and turn OFF characteristic, ratings, control
circuits design and protection circuits. Gate turn off thyristor (GTO) v-
characteristic, turn ON, turn OFF characteristic, limitation of power handling
capability, GTO snubber consideration exc., Triac and its application, power
MOSFETs, operation modes, switching characteristics, power BJT, second
breakdown, saturation and quasi saturation state.
2. Insulated Gate Bipolar Transistors (IGBT): Basis structure, V-I characteristics, 6
switching characteristics, device limitations and safe operating area (SOA) etc.
Introduction to emerging devices and circuits, MOS controlled thyristors,
integrated Gate Commutated Thyristor (IGCT), Power Integrated Circuits (PIC’s)
and smart power control chips.
3. Power Electronic Converters: Single phase and three phase uncontrolled and 8
controlled AC to DC converters analysis, DC to AC converters (inverters) single
phase half bridge, full bridge and switch mode inverters, three phase inverter with
120o and 180o mode of control, Series inverter and parallel inverters.
4. Choppers principle, first quadrant, second quadrant and multi quadrant and multi 6
quadrant choppers and their analysis. Switch mode converters AC to AC
converters, cycloconverters topology and structure of matrix power electronics
converters, converter protection and future converter applications.
5. Pulse width Modulation for Power Electronics Converters: PWM methods, 6
voltage control PWM, SPWM, selected harmonic elimination, minimum ripple
current , current control PWM, Adaptive hysteresis band method, space vector
method, performance criterion, open loop and closed loop PWM schemes etc..
6. Motor Drives Applications: Criterion for selecting drive components, DC motor 8
drives, rectifier control of DC motors, chopper control of DC drives, Multi-
quadrant control of chopper fed motors, closed loop control of DC drives,
Introduction to Induction motor drives: Comparison of variable frequency drives.
Field orientation control principles for induction motors, Introduction to
synchronous motors drives and PMBLDC drives. Electric Utility Applications:
DRAFT EC-63
Brief introduction to UPS, HVDC, Static VAR compensators and STATCOM,
Active filters .
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. “Power Electronics: Circuits Devices & Applications” by Rashid M H, 2nd Edition; 1993
Prentice Hall.
2. “Power Electronic, Converters, Applications and Design” by Ned Mohan, Tore. 3. 1989
3. “Power Electronics” by M.Undeland and William P. Robbins; John Wiley & Sons,. 1995
2nd edition
ISBN 9971511770, 9789971511777
4. “Power Semiconductor Controlled Drives” by Gopal K. Dubey; Prentice Hall, 2007
Englewood cliffs, New Jersey.
5. “Modern Power Electronics and Variable Frequency Drives” by B.K. Bose; 2009
Pearson Education, India.
6. Power Electronics by P.S.Bhimra, 4th edition, Khanna Publications. 2002
1. Subject Code: EC415 Course Title: System on Chip Design

5. Credits: 4
6. Semester: VII
9. Objective: To introduce basics of SOC design and modelling techniques with emphasis on architectural
exploration.
Hours
1. Introduction to the System Approach: System Architecture, Components of the 7
system, Hardware & Software, Processor Architectures, Memory and Addressing.
System level interconnection, An approach for SOC Design, System Architecture
and Complexity.
2. Processors: Introduction , Processor Selection for SOC, Basic concepts in 9
Processor Architecture, Basic concepts in Processor Micro Architecture, Basic
elements in Instruction handling. Buffers: minimizing Pipeline Delays, Branches,
More Robust Processors, Vector Processors and Vector Instructions extensions,
VLIW Processors, Superscalar Processors.
DRAFT EC-64
3. Memory Design for SOC: Overview of SOC external memory, Internal Memory, 9
Size, Scratchpads and Cache memory, Cache Organization, Cache data, Write
Policies, Strategies for line replacement at miss time, Types of Cache, Split – I,
and D – Caches, Multilevel Caches, Virtual to real translation , SOC Memory
System, Models of Simple Processor – memory interaction.
4. Interconnect Customization and Configuration: Inter Connect Architectures, Bus: 9
Basic Architectures, SOC Standard Buses , Analytic Bus Models, Using the Bus
model, Effects of Bus transactions and contention time, SOC Customization: An
overview, Customizing Instruction Processor, Reconfiguration Technologies,
Mapping design onto Reconfigurable devices, Instance- Specific design,
Customizable Soft Processor, Reconfiguration - overhead analysis and trade-off
analysis on reconfigurable Parallelism.
5. Application Studies / Case Studies: SOC Design approach, AES algorithms, 8
Design and evaluation.
TOTAL 42
11. Suggested Books

S. Name of Books / Authors/ Publishers Year of
No. Publication/
Reprint
1. Computer System Design System-on-Chip by Michael J. Flynn and Wayne Luk, 2002
Wiley India Pvt. Ltd.
2. ARM System on Chip Architecture – Steve Furber by 2nd Ed., 2000, Addison 2000
Wesley
Design of System on a Chip: Devices and Components by Ricardo Reis, 1st Ed., 2004
3. Springer
4. Co-Verification of Hardware and Software for ARM System on Chip Design 1995
(Embedded Technology) by Jason Andrews Newnes,
5. System on Chip Verification Methodologies and Techniques by Prakash 2002
Rashinkar ,Peter Peterson, Leena Singh ,Springer
1. Subject Code: EC – 417 Course Title: CAD for VLSI design

5. Credits: 4
6. Semester: VII
8. Pre-requisite: EC302
Hours
1. VLSI Physical Design Automation, VLSI Design Cycle, New Trends in VLSI 7
Design Cycle, Physical Design Cycle, New Trends in Physical Design Cycle,
Design Styles, System Packaging Styles.
DRAFT EC-65
2. Partitioning – Problem formulation, Classification of Partitioning algorithms, 10
Kernighan-Lin Algorithm, Simulated Annealing, Floor Planning – Problem
formulation, Classification of floor planning algorithms, constraint based floor
planning, Rectangular Dualization, Pin Assignment – Problem formulation,
Classification of pin assignment algorithms, General and channel Pin
assignments.
Placement – Problem formulation, Classification of placement algorithms,
Partitioning based placement algorithms.
3. Global Routing – Problem formulation, Classification of global routing 8
algorithms, Maze routing algorithms, Detailed Routing – Problem formulation,
Classification of routing algorithms, Single layer routing algorithms.
4. Physical Design Automation of FPGAs: FPGA Technologies, Physical Design 9
cycle for FPGAs, Partitioning, Routing – Routing Algorithm for the Non-
Segmented model, Routing Algorithms for the Segmented Model;
Physical Design Automation of MCMs: Introduction to MCM Technologies,
MCM Physical Design Cycle.
5. Chip Input and Output Circuits: ESD Protection, Input Circuits, Output Circuits 8
and noise, On-chip clock Generation and Distribution, Latch-up and its
prevention.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Algorithms for VLSI Physical Design Automation by Naveed Shervani, 3rd 2005
Edition, Springer International Edition.
2. CMOS Digital Integrated Circuits Analysis and Design – Sung-M Kang, Yusuf 2011
Leblebici, TMH, 3rd Ed.
3. VLSI Physical Design Automation-Theory and Practice by Sadiq M Sait, Habib 1999
Youssef, World Scientific.
4 Algorithms for VLSI Design Automation, S. H. Gerez, 1999, Wiley 1999
student Edition, John Wiley and Sons (Asia) Pvt. Ltd.
5. VLSI Physical Design Automation by Sung Kyu Lim, Springer 2000
1. Subject Code: EC419 Course Title: Memory Design

5. Credits: 4
6. Semester: VIII
8. Pre-requisite: EC302
9. Objective: To provide in-depth coverage in the area of memory design for testing, fault tolerance,
failure modes and mechanisms .
Hours
1. SRAM technologies – MOS, SOI , SRAM Cell structures and architecture, 8
peripheral circuit operation, SOI technology, Advanced SRAM architectures and
technologies, Application specific SRAMs, DRAM – DRAM technology
DRAFT EC-66
development, CMOS DRAM, cell theory and advanced cell structures, soft error
failure in DRAM.
2. Non-volatile Memories: Masked ROMs, High density ROM, PROM, CMOS 8
PROMS, EPROM, Floating gate EPROM cell, One time programmable EPROM,
EEPROM, EEPROM technology and architecture, Non-volatile SRAM, Flash
Memories .
3. RAM fault modelling, Electrical testing, Pseudo Random testing, Megabit DRAM 8
Testing, non-volatile memory modelling and testing, IDDQ fault modelling and
testing, Application specific memory testing, RAM fault modelling, BIST
techniques for memory.
4. General reliability issues, RAM failure modes and mechanism, Non-volatile 9
memory reliability, reliability modelling and failure rate prediction, Design for
Reliability, Reliability Test Structures, Reliability Screening and qualification,
Radiation effects, Single Event Phenomenon (SEP).
5. RAMs (FRAMs), GaAs FRAMs, Analog memories, magneto resistive RAMs 9
(MRAMs), Experimental memory devices, Memory Hybrids and MCMs (2D),
Memory Stacks and MCMs (3D), Memory MCM testing and reliability issues,
Memory cards, High Density Memory Packaging Future Directions.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Semiconductor Memories Technology by Ashok K. Sharma, Wiley. 2002
2. Advanced Semiconductor Memories by Architecture, Design and Applications - 2002
Ashok K. Sharma- Wiley.
3. Modern Semiconductor Devices for Integrated Circuits by Chenming C Hu, 1st 1987
Ed., Prentice Hall.
1. Subject Code :EC-421 Course Title: Computer And Numerical Techniques in Electromagnetics
5. Credits: 4
6. Semester: VII
9. Objective: To introduce fundamentals of Computer And Numerical Techniques in Electromagnetics
Hours
1. Introduction: Review of Electromagnetic Theory, Classification of EM Problems, 4
Analytical Methods: Separation of Variables, Separation of Variables in
Rectangular Coordinates, Separation of Variables in Cylindrical Coordinates,
Separation of Variables in Spherical Coordinates, other Orthogonal Functions,
Poisson’s Equation Series Expansion, Practical Applications of Scattering by
Dielectric Sphere and Scattering Cross Sections, Attenuation Due to Raindrops.
2. Finite Difference Methods: Finite Difference (FD) Schemes, Finite Differencing of 10
Parabolic PDEs, Finite Differencing of Hyperbolic PDEs, Finite Differencing of
Elliptic PDEs, Band Matrix Method and Iterative Methods, Accuracy and Stability
DRAFT EC-67
of FD Solutions, Practical Applications of Guided Structures and waveguide
scattering ,Absorbing Boundary Conditions for FDTD, Finite Differencing for Non-
rectangular Systems.
3. Variational Methods: Operators in Linear Spaces, Calculus of Variations, 10
Construction of Functionals from PDEs, Rayleigh-Ritz Method, Weighted
Residual Method: Collocation Method, Subdomain Method, Galerkin Method and
Least Squares Method, Eigenvalue Problems, Practical Applications.
4. Moment Methods :Classification of Integral Equations, Connection Between 10
Differential and Integral Equations, Green’s Functions:for Free Space and for
Domain with Conducting Boundaries. Quasi-Static Problems, Scattering
Problems, Radiation Problems, Hallen’s Integral Equation, Pocklington’s Integral
Equation, Expansion and Weighting Functions, EM Absorption in the Human
Body Derivation of Integral Equations, Transformation to Matrix Equation
(Discretization), Evaluation of Matrix Elements, Solution of the Matrix Equation.
5. Finite Element Method: Solution of Laplace’s Equation: Finite Element 4
Discretization, Element Governing Equations, Assembling of All Elements,
Solving the Resulting Equations, Solution of Poisson’s Equation, Solution of the
Wave Equation, Automatic Mesh Generation using Rectangular Domains and
Arbitrary Domains. Bandwidth Reduction, Higher Order Elements: Pascal
Triangle, Local Coordinates, Shape Functions and Fundamental Matrices, Three-
Dimensional Elements, Finite Element Methods for Exterior Problems using
Infinite Element Method, Boundary Element Method and Absorbing Boundary
Conditions.
6. Transmission-line-matrix Method: Solution of Diffusion Equation, Solution of 4
Wave Equations, Inhomogeneous and Lossy Media in TLM, Three-Dimensional
TLM Mesh, Error Sources and Correction, Absorbing Boundary Conditions
TOTAL 42
11. Suggested Books

S.No. Name of Books / Authors/ Publishers
1. Numerical Techniques in Electromagnetics with MATLAB,Third Edition by Matthew N.O. Sadiku

Publication/
Reprint
1. Numerical Techniques in Electromagnetics with MATLAB,Third Edition by 2011
Matthew N.O. Sadiku
1. Subject Code: EC 423 Course Title: Internet and Web Technology

5. Credits: 4
6. Semester: VIII
9. Objective: Introduction to networks and internet fundamentals and WWW.
Hours
DRAFT EC-68
1. Electronic Mail and Internet: Introduction, advantages and disadvantages, User 8
ids, Pass words, e-mail addresses, message components, message
composition, mailer features, E-mail inner workings, E-mail management, Mime
types, Newsgroups, mailing lists, chat rooms.
2. Introduction to networks and internet, history, Working of Internet, Internet 8
Congestion, internet culture, business culture on internet. Collaborative
computing & the internet. Modes of Connecting to Internet, Internet Service
Providers(ISPs), Internet address, standard address, domain name, DNS,
IP.v6.Modems and time continuum, communications software; internet tools.
3. World Wide Web : Introduction, Miscellaneous Web Browser details, searching 10

the www: Directories search engines and meta search engines, search
fundamentals, search strategies, working of the search engines, Telnet and FTP.
Introduction to Browser, Coast-to-coast surfing, hypertext markup language,
Web page installation, Web page setup, Basics of HTML & formatting and
hyperlink creation. Using FrontPage Express, Plug-ins.
4. Languages: Basic and advanced HTML, java script language, Client and Server 8
Side Programming in java script. Forms and data in java script, XML basics.
Introduction to Web Servers: PWS, IIS, Apache; Microsoft Personal Web Server.
Accessing & using these servers.
5. Privacy and security topics: Introduction, Software Complexity, Encryption 8
schemes, Secure Web document, Digital Signatures, Firewalls.
TOTAL 42
11.Suggested Books

Publication/
Reprint
1. TMH Internet & World Wide Programming, Deitel, Deitel & Nieto, Pearson 2000
Education
2. Fundamentals of the Internet and the World Wide Web, Raymond Greenlaw and 2001
Ellen Hepp
1. Subject Code: EC425 Course Title: Mixed Signal Design

5. Credits: 4
6. Semester: VII
8. Pre-requisite: EC 201, EC202
9. Objective: To design mixed-signal building blocks and understand various architectures in mixed signal
modes.
Hours
1. Switched Capacitor Circuits: Introduction to Switched Capacitor circuits- basic 11
building blocks, Operation and Analysis, Non-ideal effects in switched
capacitor circuits, Switched capacitor integrators first order filters, Switch
sharing, biquad filters.
DRAFT EC-69
2. Phased Lock Loop (PLL):Basic PLL topology, Dynamics of simple PLL, 10
Charge pump PLLs-Lock acquisition, Phase/Frequency detector and charge
pump, Basic charge pump PLL, Non-ideal effects in PLLs-PFD/CP non-
idealities, Jitter in PLLs, Delay locked loops, applications
3. Data Converter Fundamentals: DC and dynamic specifications, Quantization 11
noise, Nyquist rate D/A converters- Decoder based converters, Binary-Scaled
converters, Thermometer-code converters, Hybrid converters
4. Nyquist Rate A/D Converters: Successive approximation converters, Flash 10
converter, Two-step A/D converters, Interpolating A/D converters, Folding A/D
converters, Pipelined A/D converters, Time-interleaved converters.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. CMOS Mixed Signal Circuit Design by J. Baker, Wiley Student Edition 2000
2 CMOS Analog Circuit Design by Philip E. Allen and Douglas R. Holberg, 2010
Oxford University Press, International Second Edition/Indian Edition,
3. Analog Integrated Circuit Design by David A. Johns, Ken Martin, Wiley Student 2013
Edition
4. CMOS Integrated Analog-to- Digital and Digital-to-Analog converters by Rudy 2003
Van De Plassche, Kluwer Academic Publishers
5. Understanding Delta-Sigma Data converters by Richard Schreier, Wiley 2000
Interscience.
DRAFT EC-70
1. Subject Code: EC408 Course Title: Low power VLSI Design
5. Credits: 4
6. Semester: VIII
8. Pre-requisite: EC 302
9. Objective: To learn and apply in practice technology level , circuit level and system level power
optimization techniques.
Hours
1. Introduction: Need for low power VLSI chips, Power and Energy basics, Sources 7
of power dissipation, important parameters for low power design, Low power
design approaches. Device & Technology Impact on Low Power.
2. Low power design flow, SPICE circuit simulators, gate level logic simulation, 9
capacitive power estimation, static state power, gate level capacitance
estimation, architecture level analysis, data correlation analysis in DSP systems.
Monte Carlo simulation. Probabilistic power analysis: Random logic signals,
probability & frequency, probabilistic power analysis techniques, signal entropy.
3. Low Power Techniques : Circuit level: Power consumption in circuits. Dynamic 9
Power Optimization: multiple supply voltages, transistor sizing, Static power
Optimization: Multiple thresholds transistor
Flip Flops and Latches design, high capacitance nodes, low power digital cells
library. Logic level: Gate reorganization, signal gating, logic encoding, state
machine encoding, pre-computation logic.
4. Low power Architecture and Systems Power & performance management, 9
switching activity reduction, parallel architecture with voltage reduction, flow
graph transformation, low power arithmetic components, low power memory
design. Low power Clock Distribution: Power dissipation in clock distribution,
single driver Vs distributed buffers, Zero skew Vs tolerable skew, chip & package
co design of clock network.
5. Design of low power arithmetic elements: addition, Multiplication, Division. 8
Optimizing Power at Standby: Clock gating, power gating, body biasing, supply
voltage ramping, Power reduction of memory in standby mode using voltage
scaling and body biasing. Optimizing Power at Runtime: Dynamic voltage and
frequency scaling, adaptive body biasing, Power domains and power
management.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Low Power Design Methodologies by J. M. Rabaey, M.Pedram, KAP 2006
2. Practical Low Power Digital VLSI Design by Gary K. Yeap, KAP, 2002 2002
3. Digital Integrated Circuits: A Design Perspective, Second Edition by J. M. 2000
Rabaey, A. P. Chandrakasan and B. Nikolic, PH/Pearson.
4. Low-Power CMOS VLSI Circuit Design by K. Roy and S. C.Prasad Wiley. 1996
5. Low-Power CMOS Design,P. Chandrakasan and RW Broderson, IEEE Press. 2000
DRAFT EC-71
1. Subject Code: EC - 410 Course Title: Advance Coding Theory
5. Credits: 4
6. Semester: VIII
9. Objective: To introduce Advance Coding Theory concepts.
Hours
1. Information Theory : Information – Entropy, Information rate, classification of 10
codes, Kraft McMillan inequality, Source coding theorem, Shannon-Fano
coding, Huffman coding, Extended Huffman coding - Joint and conditional
entropies, Mutual information - Discrete memoryless channels – BSC, BEC –
Channel capacity, Shannon limit.
2. Error Control Coding : Definitions and Principles: Hamming weight, Hamming 10
distance, Minimum distance decoding - Single parity codes, Hamming codes,
Repetition codes - Linear block codes, Cyclic codes - Syndrome calculation,
Encoder and decoder - CRC Convolutional codes – code tree, trellis, state
diagram - Encoding – Decoding: Sequential search and Viterbi algorithm –
Principle of Turbo coding.
3. Source Coding : Text, Audio and Speech : Text: Adaptive Huffman Coding, 10
Arithmetic Coding, LZW algorithm – Audio: Perceptual coding, Masking
techniques, Psychoacoustic model, MEG Audio layers I,II,III, Dolby AC3 -
Speech: Channel Vocoder, Linear Predictive Coding.
4. Source Coding : Image and Video : Image and Video Formats – GIF, TIFF, 12
SIF, CIF, QCIF – Image compression: READ, JPEG – Video Compression:
Principles-I,B,P frames, Motion estimation, Motion compensation, H.261, MPEG
standard.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. R Bose, “Information Theory, Coding and Cryptography”, TMH 2007
2 Fred Halsall, “Multimedia Communications: Applications, Networks, Protocols 2002
and Standards”, Pearson Education Asia,
1. Subject Code: EC - 412 Course Title: Machine Learning

5. Credits: 4
6. Semester: VII
9. Objective: To introduce fundamentals of Machine Learning
DRAFT EC-72
Hours
1. Introduction to Machine Learning :Learning Associations; Classification, 4
Regression, Annotation, Supervised Unsupervised, Semi supervised, learning
Basic tools: Linear classification, regression, Feature maps, Trees, Instance based
classifiers.
2. Supervised Learning :Learning a Class from Examples like Optical character 10
recognition Bioinformatics Computational advertising Self‐driving cars Network
security, Vapnik-Chervonenkis Dimension, Probably Approximately Correct
Learning, Noise, Learning Multiple Classes, Regression, Model Selection and
Generalization, Dimensions of a Supervised Machine Learning Algorithm.
3. Decision Tree Learning: Univariate trees Objective functions & criteria for splitting 10
Pruning rule extraction from trees Learning rules from data multivariate trees Fast
implementations Acceleration by Chernoff bounds Data distribution.
4. Linear Decision Functions & Perception Learning,Linear Discrimination: 10
Generalizing the Linear Model, Geometry of the Linear Discriminant, Pairwise
Separation, Parametric Discrimination, Gradient Descent Logistic Discrimination,
Discrimination by Regression.
5. Multi-Layer Perception Networks: Perceptron, Training a Perceptron Learning 4
Boolean Functions Backpropagation Algorithm Convergence proof, Properties
Training procedures, tuning the network size, Bayesian view of learning,
dimensionality reduction, Learning time, deep learning, Kernel trick: Basic idea,
Kernel Perceptron, Kernel expansion, Kernel examples.
6. Reinforcement Learning ,Single State Case: K-Armed Bandit, Elements of 4
Reinforcement Learning, Model-Based Learning Value Iteration Policy methods
Policy evaluation Policy iteration Policy gradient Policy Iteration Temporal
Difference Learning Exploration Strategies Deterministic Rewards and Actions
Nondeterministic Rewards and Actions Eligibility Traces.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Introduction to Machine Learning Ethem Alpaydın 2013
The MIT Press (ISBN: 9780262012430)
2. A First Course in Machine Learning CRC Press Taylor and Francis (ISBN 2011
9781439824146)
1. Subject Code: EC 414 Course Title: EMC / EMI

5. Credits: 4
6. Semester: VIII
9. Objective: The student shall be able to understand the root causes for Electromagnetic Noise, its
sources, its effects and the required precautions to be taken, their measurement techniques and the
DRAFT EC-73
influences of them in detail. Also the student will understand different compatibility techniques to suppress
EMI/EMC and finally the standards that have been following in the world in the field of EMI/EMC.
Hours
1. 8
BASIC CONCEPTS: History and concepts of EMI, Definition of EMI and EMC
with examples, Classification of EMI/EMC - CE, RE, CS, RS, Units of
Parameters, Sources of EMI/EMC, EMI coupling modes - CM and DM, ESD
Phenomena and effects, Transient phenomena and suppression,
electromagnetic pulse (EMP), Radiation Hazards, frequency spectrum
conservation, mechanisms of EMI generation, EMI testing, Methods of
elimination and Biological effects of EMI
2. 9
EMI MEASUREMENTS: Basic principles of RE, CE, RS and CS measurements,
EMI measuring instruments- Antennas, LISN, Feed through capacitor, current
probe, EMC analyzer and detection technique open area site, shielded ferrite
lined anechoic chamber, Tx/Rx Antennas, Sensore, Injectors/Couplers and
coupling factors, TEM cell.
3. 9
EMC STANDARD AND REGULATIONS: National and Intentional standardizing
organizations- FCC, CISPR, ANSI, DOD, IEC, CENEEC, FCC CE and RE
standards, CISPR, CE and RE Standards, IEC/EN, CS standards, Frequency
assignment, spectrum conversation, EN emission and susceptibility standards
and specifications
4. 9
EMI CONTROL METHODS AND FIXES : Shielding, Grounding, Bonding,
Filtering, Filter installation and evaluation, Isolation transformer, opto isolator,
Transient suppressors, EMI gasket
5. 7
MC DESIGN AND INTERCONNECTION TECHNIQUES :Cable routing and
connection, signal control, Component selection and mounting, PCB design-
Trace routing, Impedance control, decoupling, Zoning and grounding, VIAs
connection, Terminations, Electromagnetic pulse- Noise from relays and
switches, Power decoupling.
TOTAL 42
11. Suggested Books

1.
Prasad Kodali.V – Engineering Electromagnetic Compatibility – S.Chand&Co. 2000
2
Clayton R.Paul – Introduction to Electromagnetic compatibility – Wiley & Sons 1992
3. Electromagnetic Interference and Compatibility IMPACT series, IIT-Delhi, Modules 1-9.

4. Bemhard Keiser, “Principles of Electromagnetic Compatibility”, 3rd Ed, Artech house,
Norwood. 1986
DRAFT EC-74
1. Subject Code: EC 416 Course Title: Pattern Recognition
5. Credits: 4
6. Semester: VIII
8. Pre-requisite: Digital Image Processing, Digital Signal Processing
9. Objective: To introduce the practical applications of pattern recognition, representation of various
patterns, classification pattern recognition methodologies, designing of classifiers and dimensionality of
feature vectors.
Hours
1. Introduction to pattern recognition, machine perceptron, pattern recognition 4
system, design cycle, learning and adaptation, applications of pattern
recognition, pattern representations.
2. Introduction to probability theory, conditional probabilities, random variables, 8
binomial distribution, Poison distribution, uniform distribution, normal
distributions, joint distribution and densities, moment of random variables,
bivariate distributions, multivariate normal distributions, Maximum likelihood
estimate, unbiased estimate, minimum risk estimate.
3. Bayesian decision theory; state of nature, prior probabilities, posterior 8
probabilities, decision rule, likelihood, loss function, two-category classification,
decision boundary, minimum error rate classification, discriminant function for
normal density, conditionally independent features, Bayesian belief network,
leave-one-out scheme, characteristic curve.
4. Non-parametric decision techniques, kernel and window estimator, nearest 8
Neighbor classification, nearest Neighbour error rate, K-nearest Neighbour
techniques, convergence of nearest Neighbour, computational complexity of K-
nearest Neighbour, Fisher linear discriminant, Multiple discriminant analysis.
5. Introduction to Linear and Nonlinear Classifiers: linear discriminant functions 8
and decision hyperplanes, perceptron algorithms, least square method, mean
square error estimation, stochastic approximation, sum of error square
estimation, mean square error regression, logistic discrimination, support vector
machine separable class and non-separable class.
6. Data transformation and dimensionality reduction, basis vector and images, The 6
Karhunen-Love transform, the singular value decomposition, independent
component analysis, non-negative matrix factorization, non-linear dimensional
reduction techniques; KPCA, LLE, ISOMAP.
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Pattern Classification/Duda and Hart/ Wiley International 2003
2. Pattern Recognition/ Theodoridis and Koutroumbas/ Acdemic Press4 th 2009
Edition/
3. Pattern Recognition and Machine Learning/Bishop, Christopher/Springer 2006
DRAFT EC-75
4. Introduction to Statistical Pattern Recognition/ KeinosukeFukunaga/Academic 2nd Edition/
Press
5. Pattern recognition and Image Analysis/ Gose, Johnsonbaugh, Jost/ PHI 1997
1. Subject Code: EC 418 Course Title: Estimation & Detection Theory

5. Credits: 4
6. Semester: VI
9. Objective: To introduce fundamentals of Detection and estimation.
Hours
1. Review of Gaussian variables and processes; problem formulation and objective 10
of signal detection and signal parameter estimation in discrete-time domain
Statistical Decision Theory: Bayesian, minimax, and Neyman-Pearson decision
rules, likelihood ratio, receiver operating characteristics, composite hypothesis
testing, locally optimum tests, detector comparison techniques, asymptotic
relative efficiency.
2. Detection of Deterministic Signals: Matched filter detector and its performance; 6
generalized matched filter; detection of sinusoid with unknown amplitude, phase,
frequency and arrival time, linear model.
3 Detection of Random Signals: Estimator-correlator, linear model, general 6
Gaussian detection, detection of Gaussian random signal with unknown
parameters, weak signal detection.
4 Nonparametric Detection: Detection in the absence of complete statistical 6
description of observations, sign detector, Wilcoxon detector, detectors based on
quantized observations, robustness of detectors.
5 Estimation of Signal Parameters: Minimum variance unbiased estimation, Fisher 8
information matrix, Cramer-Rao bound, sufficient statistics, minimum statistics,
complete statistics; linear models; best linear unbiased estimation; maximum
likelihood estimation, invariance principle; estimation efficiency; Bayesian
estimation: philosophy, nuisance parameters, risk functions, minimum mean
square error estimation, maximum a posteriori estimation.
6 Signal Estimation in Discrete-Time: Linear Bayesian estimation, Weiner filtering, 6
dynamical signal model, discrete Kalman filtering.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. H.Van Trees, Detection, Estimation, and Modulation Theory 1968
2. S.M. Kay's Fundamentals of Statistical Signal Processing: Estimation 1998
Theory (Vol 1), Detection Theory (Vol 2)
DRAFT EC-76
1. Subject Code: EC-420 Course Title: Cloud Computing
5. Credits: 4
6. Semester: VIII
9. Objective: To enable the students to understand the fundamental concepts of cloud and to apply them
to design, evaluate, simulate and compare its various applications in Cloud Computing.
Hours
1. Overview of Computing Paradigm, Recent trends in Computing: Grid Computing, 6
Cluster Computing, Distributed Computing, Utility Computing, Cloud Computing,
Evolution of Cloud Computing and it's vision, features.
Clouds: Introduction, History, components, types, services, challenges,
technologies, Current applications of Cloud Computing (Microsoft Azure, Google
App Engine, Amazon Web services, Hadoop etc).
Cloud Computing Architecture: Cloud computing stack, Reference Model
(Services: IaaS, PaaS, SaaS), various cloud management platforms and tools,
Deployment Models: Public cloud, Private cloud, Hybrid cloud, Community cloud.
2. Virtualization of Clouds 8
Virtualization: Introduction, Evolution, Virtualized Environment characteristics,
Server Virtualization, VM Provisioning and Manageability, VM Migration Services,
VM Provisioning in the Cloud Context, and Future Research Directions. Cloud
Security Mechanisms (Encryption, PKI, SSO, IAM)
3. Service Models: 12
Infrastructure as a Service (IaaS):Introduction, definition, virtualization, Different
approaches to virtualization, Hypervisors, Machine Image, Virtual Machine (VM),
Resource Virtualization: Server, Storage, Network Virtual Machine (resource)
provisioning and manageability, storage as a service, Data storage in cloud
computing(storage as a service), Examples: Amazon EC2 Renting, EC2
Compute Unit, Platform and Storage, pricing, customers, Eucalyptus
Platform as a Service(PaaS):Introduction, Service Oriented Architecture (SOA),
Cloud platform and management, computation, storage, Examples: Google App
Engine, Microsoft Azure, SalesForce.com
Software as a Service (SaaS):Introduction, Web services, Web 2.0, Web OS and
Case Study .
4. Service Management in Cloud Computing: Service Level Agreements(SLAs), 6
Billing & Accounting, Economics of scaling, Managing Data: Looking at Data,
Scalability & Cloud Services, Database & Data Stores in Cloud, Large Scale Data
Processing.
5. Cloud Security: Infrastructure Security, Network level security, Host level 6
security, Application level security, Data security and Storage: Data privacy and
security Issues, Jurisdictional issues raised by Data location, Identity & Access
Management, Access Control, Trust, Reputation, Risk, Authentication in cloud
computing, Client access in cloud, Cloud contracting Model, Commercial and
business considerations.
6. Case Studies: Open Source & Commercial Clouds, Eucalyptus, Microsoft 4
Azure, Amazon EC2 and introduction of software: CloudSim.
TOTAL 42
DRAFT EC-77
11. Suggested Books
Publication/
Reprint
1. Cloud Computing Bible, Barrie Sosinsky, Wiley-India, 2010
2. Cloud Computing: Principles and Paradigms, Editors: Rajkumar Buyya, 2011
James Broberg, Andrzej M. Goscinski, Wile,
3. Cloud Computing: Principles, Systems and Applications, Editors: Nikos 2012
Antonopoulos, Lee Gillam, Springer
4. Cloud Security: A Comprehensive Guide to Secure Cloud 2010
Computing, Ronald L. Krutz, Russell Dean Vines, Wiley-India,
5. Rajkumar Buyya, Christian Vecchiola, and Thamarai Selvi, Mastering 2013
Cloud Computing, Tata McGraw Hill, New Delhi, India.
1. Subject Code: EC-422 Course Title: Robotics and Machine vision

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of robotics and machine vision and to learn about the
perception, navigation and path planning for an autonomous mobile robot.
Hours
1. Introduction to Robotics: Mathematical modelling of Robots, Different kinematic 6
arrangement of manipulators, Rigid motion and homogeneous transformations:
Rotational transformation, composition of rotations and Parameterization of
rotation.
2. Mobile Robot :,Kinematic Models and Constraints :Representing robot position 8
,Forward kinematic models, Wheel kinematic constraints , Robot kinematic
constraints, Examples: robot kinematic models and constraints, Mobile Robot
Maneuverability :Degree of mobility, Degree of steerability, Robot
maneuverability, Mobile Robot Workspace : Degrees of freedom ,Holonomic
robots ,Path and trajectory considerations, Beyond Basic Kinematics ,Motion
Control (Kinematic Control): Open loop control (trajectory-following), Feedback
control.
3. Perception :Sensors for Mobile Robots :Sensor classification ,Characterizing 11
sensor performance ,Wheel/motor sensors, Heading sensors ,Ground-based
beacons, Active ranging, Motion/speed sensors, Vision-based sensors
,Representing Uncertainty : Statistical representation, Error propagation:
combining uncertain measurements ,
Machine vision: edge, corner , line detection algorithms, filtering, feature
extraction, object recognition and tracking algorithms
Feature Extraction : Feature extraction based on range data (laser, ultrasonic,
vision-based ranging) , Visual appearance based feature extraction .
DRAFT EC-78
4. Mobile Robot Localization : The Challenge of Localization (Noise and Aliasing) : 11
Sensor noise, Sensor aliasing ,Effector noise ,An error model for odometric
position estimation, To Localize or Not to Localize: Localization-Based Navigation
versus Programmed Solutions, Belief Representation :Single-hypothesis belief ,
Multiple-hypothesis belief, Map Representation :Continuous representations,
Decomposition strategies, State of the art: current challenges in map
representation, Probabilistic Map-Based Localization :Introduction, Markov
localization, Kalman filter localization, Other Examples of Localization Systems :
Landmark-based navigation ,Globally unique localization, Positioning beacon
systems ,Route-based localization ,Autonomous Map Building ,The stochastic
map technique
5. Planning and Navigation :Introduction, Competences for Navigation (Planning and 6
Reacting):Path planning, Obstacle avoidance ,Navigation Architectures :
Modularity for code reuse and sharing, Control localization , Techniques for
decomposition ,Case studies: tiered robot architectures.
TOTAL 34
11. Suggested Books
S.No Name of Books / Authors/ Publishers Year of
Publication/
Reprint
1. Robot Modeling and Control Mark W. Spong, Seth Hutchinson, and M. 2005
Vidyasagar JOHN WILEY & SONS, INC
2. Visual Perception and Robotic Manipulation 3D Object Recognition, Tracking and 2009
Hand-Eye Coordination Geoffrey Taylor Lindsay Kleeman
3. Introduction to Autonomous Mobile Robots by Roland Siegwart, MIT press 2011
4. Robot Vision (MIT Electrical Engineering and Computer Science) MIT Press 1986
5. Robotics, Vision and Control Peter Corke Springer 2011
1. Subject Code: EC-424 Course Title: Fault Tolerant Computing

5. Credits: 4
6. Semester: VIII
8. Pre-requisite:
9. Objective: To introduce the design concepts of reliable and safe computer systems.
Hours
1. Fundamental Concepts: Need for reliability, Faults as the sources of unreliability, 8
Definitions of fault tolerance, fault tolerant attributes, fault classification,
distribution models for permanent ,intermittent and transient faults.
2. Reliability Techniques: Information redundancy, hardware redundancy, and time 9
redundancy. Basic approaches to hardware redundancy: Error masking,
Dynamic redundancy, Hybrid hardware redundancy.
DRAFT EC-79
3. Maintainability and testing techniques :Specification based diagnosis and system 8
based diagnosis; Financial Considerations, Cost models.
4. Dependability Evaluation Techniques: Reliability and availability models: 9
(Combinatorial techniques, Fault-Tree models, Markov models), Performability
Models.
5. Architecture of Fault-Tolerant Computers (case study): General-purpose 8
systems, high-availability systems, long-life systems, critical systems. Recent
topics in fault tolerant systems: Security, fault tolerance in wireless/mobile
networks and Internet.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Reliable Computer Systems Design and Evaluation by Daniel P. 1998
Siewiorek and Robert S. Swarz .AK Peters Ltd.
2. Fault-Tolerant Computing: Theory and Techniques Vol. I,II by D. K. 1986
Pradhan , Prentice-Hall.
3. Fault Tolerance in Distributed Systems by Pankaj Jalote, Prentice Hall. 1994
4. Design and Analysis of Fault Tolerant Digital System by Barry W. 1989
Johnson, Addison-Wesley
1. Subject Code: EC 426 Course Title: Distributed Computing

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of computing and distributed system.
Hours
1. Introduction to Distributed Systems, Design Goals, Types of Distributed systems, 6
system architectures and fundamental models, middleware, Threads,
virtualization, client-Server Model, Code migration .
2. Communication fundamentals, Remote Procedure Call, message oriented 6
communication, and stream oriented communication, multicast communication.
3. Synchronization: clock synchronization, logical clocks, mutual exclusion 10
algorithms: centralized, decentralized, distributed and token ring algorithms,
election algorithms.
4. Replication management: need for replication, consistency models: data centric 6
and client centric consistency models, replica management, consistency
protocols: continuous, primary-based, replicated-write and cache-coherence
protocols.
DRAFT EC-80
5. Fault tolerance: basic concepts and failure models Classification of Failures in 6
Distributed Systems, Basic Techniques for Handling Faults in Distributed
Systems, process resilience, reliable client-server and group communication,
distributed commit recovery mechanisms.
6. Security in distributed systems, secure channels, authentication, integrity and 8
confidentiality, access control, security management. Naming: Flat naming
approaches, structured naming, name space and resolution, attribute- based
naming, directory services, LDAP, decentralized implementations.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Distributed Systems, Principles and Paradigms by Andrew S. Tanenbaum 2006
and Maarteen Van Steen, Pearson Education.
2. Coulouris, Dollimore, Kindberg, "Distributed System: Concepts and 2012
Design”, Pearson Ed.
1. Subject Code: EC 428 Course Title: Neuro Electronics

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of Neuro Electronics
Hours
1. Introduction to Neuro electronics; neuron: architecture, resting membrane 6
potential, action potentials, axon hillock, synapse, presynaptic cell, postsynaptic
cell, synaptic cleft, communication between neurons, neuro-transmitters,
synaptic potential, depolarization, hyperpolarization.
2. Recording electrical signals from neurons: voltage–clamp technique, patch- 6
clamp technique. EEG (Electroencephalography)
Neuro electronic Interfacing: Iono-Electronic Interface, Neuron-Silicon Circuits,
Brain-Silicon Chips. Electrical Dynamics of the Neuron-Chip Interface on a
Nanoscopic Level. Interfacing neurons with carbon nanotubes: Electrical signal
transfer and synaptic stimulation in cultured brain circuits. Nanowire Integrated
Microelectrode Arrays for Neuro-electronic Applications
3. Techniques for neuro electronic interfacing: thin-film technology, micro-electrode 9
arrays (MEAs), Field-Effect-Transistor arrays (FETs), CMOS integrated
systems, Nano technology and Bio-chemistry, EOSFET (Electrolyte Oxide
Silicon Field Effect Transistor), EOS Capacitors(Electrolyte Oxide Silicon
Capacitors).
4. Elementary neuro electronic hybrids: Cellular neuro-prostheses, neuronal 9
memory on chip. Neuronal networks on chip. Iono-electronic Devices, Neuro
electronic Processors.
DRAFT EC-81
5. Neuro-prosthetics: sensory prosthetics, motor prosthetics, cognitive prostheses. 12
Artificial pacemakers, cochlear implants, deep brain stimulation, brain-computer
interface, MRI, Image-Guided Surgery.
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Principles of Neural Sciences, 4th Edition, by E. R. Kandel,J. H. Schwartz, T. M. 2000
Jessell ,McGraw-Hill Companies
2. Neuroscience, 3rd Edition by D. Purves, G. J. Augustine,D. Fitzpatrick, L. C. 1997
Katz, A.- S. LaMantia, J. O. McNamara,S. M. Williams ,Sinauer Associates Inc.,
1997
3. Biophysics of Computation (Information Processing inSingle Neurons) by C. 1999
Koch ,Oxford University Press
4. Neuro-prosthetics (Theory & Practice) by K W Horch, G S Dhillon ,World 2004
Scientific Publishing
5. Introduction to Molecular Neurobiology by Z. W. Hall, Sinauer Associates Inc. 1992
6. Sensation & Perception by E. Bruce Goldstein ,Wadsworth Cengage 2007

Learning,(8thEdition)
1. Subject Code: EC 430 Course Title: Advance Computer Architecture

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals concepts of advanced computer architecture.
Hours
1. Review of Basic Organization and Architectural Techniques, RISC processors, 8
Characteristics of RISC processors, RISC Vs CISC, Classification of Instruction
Set Architectures, Review of performance measurements, Basic parallel
processing techniques: instruction level, thread level and process level,
Classification of parallel architectures.
2. Instruction Level Parallelism, Basic concepts of pipelining, Arithmetic pipelines, 10
Instruction pipelines, Hazards in a pipeline: structural, data, and control hazards,
Overview of hazard resolution techniques, Dynamic instruction scheduling,
Branch prediction techniques, Instruction-level parallelism using software
approaches, Superscalar techniques, Speculative execution, Review of modern.
Pentium Processor: IA 32 and P6 micro architectures, ARM Processor.
DRAFT EC-82
3. Memory Systems: Cache Memory, main memory design, and Virtual Memory 4
I/O Systems: Design Issues, Performances Measures. Loosely Coupled &
Tightly Coupled Systems, Concurrency & Synchronization, RAID .
4. Peripheral Devices, Bus structures and standards, Synchronous and 8
asynchronous buses, Types and uses of storage devices, Interfacing I/O to the
rest of the system, Reliability and availability, I/O system design, Platform
architecture.
5. Thread Level Parallelism, Centralized vs. distributed shared memory, 8
Interconnection topologies, Multiprocessor architecture, Symmetric
multiprocessors, Cache coherence problem, Synchronization, Memory
consistency, Multicore architecture, Review of modern multiprocessors.
Process Level Parallelism, Distributed computers, Clusters, Grid, Mainframe 4
6. computers, Multi-core Architecture .
TOTAL 42
11. Suggested Books
S.No. Name of Books / Authors/ Publishers Year of Publication/
Reprint
1. “Parallel processing and Architecture” by K.Hwang and F.Briggs; 1994
McGraw Hill.
2. “Computer architecture: A Quantitative approach” by John 1996
Hennessy and David Patterson; Morgan Kaufmann Publishers Inc
3. Structured Computer Organisation by A S Tanenbaum, Pearson 2012
publication, ISBN-13: 978-0132916523
1. Subject Code: EC432 Course Title: Bio-Impedance Based Measurements

5. Credits: 4
6. Semester: VIII
9. Objective:To familiarize the students with the concepts of basics of Bio-Impedance based
Measurements.
S. Contents Contact
No. Hours
Electrolytics: Ionic and electronic dc conduction, ionization molecular bonds, Bulk
electrolytic dc conductance, interface phenomena, Electrodes and ac phenomena,
1. 06
Dielectrics: Polarization in uniform dielectric, basic membrane experiment, Dispersion
and dielectric spectroscopy.
Electrical properties of tissues, basic biomaterials, cells, tissue and organs, Special
2. electrical properties, tissue, anisotropy, Tissue dc properties, Nerves and muscles 08
excited, Piezo electric and triboelectric effect.
Instrumentation and measurements: General network theory, The black box,
admittance, Impedance, Immittance, Two port Network, Reciprocity Theorem, Extended
3. Immittance concepts, Signal and measurements; dc static values and ac, periodic 08
waveforms, Aperiodic waveforms, spectrum analysis, Fourier transforms, Signal
generators, Operational Amplifiers and Filters, Neural Networks and Wavelets Analysis.
Bridges, Impedance Analyzers, Lock in amplifiers, Digital Lock in amplifiers, Analogue
4. lock in amplifiers, Current mode lock in amplifiers, Impedance analyzers and LCR 06
meters.
DRAFT EC-83
Applications, Electrodes, Design and Properties, ECG, Impedance plethysmography,
5. EEG, ENG/ERG/EOG, Electrotherapy, Body Composition, Cardiac pacing, 08
Defibrillation, Electroshock, Electro-surgery.
Latest trends in bio-impedance measurements, validation & calibration of bio-
impedance, challenges in measurement, analysis, validation of bio-impedance,
6. 06
Calibration of bio-impedance measuring instruments. Future scope of bio-impedance
based non-invasive medical diagnostics.
Total 42

No. Publication/
Reprint
1. S. Grimn “Bio-impedance and bioelectricity”, Springer Publication. 2000
2. Jaakko Malmivuo “Bio-electromagnetism Principles and Applications”, Springer 1995
Publications.
3. Joseph D.Bronzino, “The Biomedical Engineering handbook”, CRC Press. 1999
4. Wavelets in medicine and biology by Akram Aldroubi and Michael Unser. CRC 1996
press.
1. Subject Code: EC 434 Course Title: Fundamentals of MIMO

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of MIMO
Hours
1. Introduction: MIMO wireless communication, MIMO channel and signal model, 8
A fundamental trade-off, MIMO transceiver design, MIMO in wireless networks,
MIMO in wireless standards, Organization of the book and future challenges.
2. Capacity limits of MIMO systems :Introduction, Mutual information and Shannon 10
capacity, Single-user MIMO, Multi-user MIMO, Multi-cell MIMO, MIMO for adhoc
networks,
3. Precoding design :Transmit channel side information, Information-theoretic 4
foundation for exploiting CSIT, A transmitter structure, Pre-coding design criteria,
Linear pre-coder designs ,Pre-coder performance results and discussion,
Applications in practical systems
4. Space–time coding for wireless communications: principles and applications : 8
Introduction, Background, Space–time coding principles ,Applications,
Discussion and future challenges.
5. Fundamentals of receiver design: Introduction, Reception of uncoded signals, 8
Factor graphs and iterative processing, MIMO receivers for uncoded signals,
MIMO receivers for coded signals, Some iterative receivers.
Multi-user receiver design: Introduction, Multiple-access MIMO systems, Iterative 4

6. space–time multi-user detection, Multi-user detection in space–time coded
systems, Adaptive linear space–time multi-user detection,
DRAFT EC-84
TOTAL 42
11. Suggested Books

Publication/
Reprint
1. Introduction to MIMO Communications By Jerry R. Hampton Publisher: 2013
Cambridge University Press.
2. MIMO Wireless Communications Ezio Biglieri, Robert Calderbank, 2007
Anthony Constantinides, Andrea Goldsmith, Arogyaswami Paulraj
1. Subject Code: EC – 436 Course Title: Advance Microwave and Antenna Design
5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of Advance Microwave and Antenna Design
Hours
1. Transmission lines for Microwave Integrated Circuits: MIC transmission line 10
structures, Monolithic microwave integrated circuits(MMCs),quasi TEM mode
propagation, static TEM parameters(Z0,εeff) Synthesis: the width to height ratio
(w/h),formulae for accurate static TEM calculations, analysis
formulae(w/h),examples of static TEM synthesis.
2. Behaviour and design at microwave frequencies: effect of finite strip thickness, 8
metallic enclosure, dispersion in microstrip, discontinuities in microstrip lines:
Foreshortened open circuit, series gap microstrip short circuits, right angle bend
or corner, matched microstrip bends, frequency dependence of discontinuities
effects.
3. Antennas: Review of Basic Fundamental Concepts of antenna and its 8
parameters, Aperture antenna: Huygen’s principle, radiation from rectangular
and circular apertures, design considerations, Babinet’s principle, Radiation from
sectoral and pyramidal horns, design concepts.
4. Microstrip Antennas: Basic characteristics of microstrip antennas, feeding 8
methods, methods of analysis, design of rectangular and circular patch antennas.
5. Basic Concepts of Smart Antennas: Concept and benefits of smart antennas, 8
fixed weight beam forming basics, Adaptive beam forming.
TOTAL 42
11. Suggested Books

S. Name of Books / Authors/ Publishers Year of Publication/
No Reprint
.
DRAFT EC-85
1. T.C.Edwards, “Foundation for microstrip circuits design”, J. Wiley and 2016
sons.
2. E.H.Fooks and R.A.Zakarevicius, “Microwave Engineering Using 1990

Microstrip Circuits, Prentic Hall.
3. C. A. Balanis, "Antenna Theory and Design", 3rd Ed., John Wiley &Sons. 2005
4. R. E. Collin, "Antennas and Radio Wave Propagation", McGraw-Hill. 1985
5. F. B. Gross, "Smart Antennas for Wireless Communications", McGraw- 2005

Hill.
6. Bharathi Bhat, S. K. Koul, “Stripline-like Transmission Lines for 1989

Microwave Integrated Circuits” New Age international.
7. W. L. Stutzman, and G. A. Thiele, "Antenna Theory and Design", 2nd Ed., 1998
John Wiley &Sons.
8. R. S. Elliot, "Antenna Theory and Design", Revised edition, Wiley-IEEE 2003
Press.
1. Subject Code: EC - 438 Course Title: Radar and Satellite Communication

5. Credits: 4
6. Semester: VIII
9. Objective: To introduce fundamentals of Radar and Satellite Communication
Hours
1. Radar Introduction : Principle of detection and ranging, Radar frequencies and 6
bands. Applications, Radar block diagram and operation, Radar Range Equation,
Range prediction, Minimum detectable signal, Receiver noise, SNR, Integration
of radar pulses, Radar cross section of targets, Transmitter Power, PRF and
system losses & Propagation effects.
2. CW FM Radar : Doppler effect, CW Radar, Frequency-modulated CW Radar, 6
Multiple-frequency CW Radar. MTI and Pulse Doppler Radar, MTI delay lines,
Delay line Cancelers, Coherent and Non-Coherent MTI, Pulse Doppler Radar.
3. Satellite orbits : Solar day and sidereal day, orbital parameters, satellite 10
trajectory, period, velocity and position of a satellite, geostationary satellites, non-
geostationary constellations. Launching of geostationary satellites,
Communication satellites, spacecraft subsystems, payload, repeater, antenna,
attitude and control systems, tracking and command
DRAFT EC-86
4. Earth stations : fixed and mobile satellite service earth stations. Communication 6
link design - frequency bands used, antenna parameters - transmission
equations - noise considerations - link design - very small aperture terminals
(VSAT).
5. Multiple access techniques : frequency division multiple access - time division 6
multiple access - code division multiple access - access protocols for data
traffic. Performance analysis and comparative analysis of FDMA,TDMA and
CDMA.
TOTAL 42
11. Suggested Books

1. Introduction to Radar Systems, by Merrill I. Skolnik; Tata McGraw-Hill (3rd Edition) 2003
2. Satellite Communication, Dennis Roddy, McGraw Hill
3. Radar Principles, by Peyton Z Peeble; John Wiley 2004
4. Principles of Radar, by J C Toomay 2004
5. Satellite Communication Systems, by Richharia M.; Macmillan Press
6. Satellite Communication, by Gagliardi R.M.; CBS
7. Digital Satellite Communication, by Ha T.T.; McGraw Hill
Syllabus of University Electives offered by ECE department

1. EC-351 Mechatronics
2. EC-353 Computer Vision
3. EC-355 Embedded System
4. EC-357 Digital Image Processing
5. EC-359 VLSI Design
DRAFT EC-87
1. Subject Code: EC – 351 Course Title: Mechatronics
5. Credits: 4
6. Semester: V
7. Subject Area: UE
9. Objective: To introduce fundamentals of Mechatronics
Hours
1. Introduction : Basic Definitions and key elements of Mechatronics, Mechatronic 6
Design Approach: Functions of Mechatronic Systems, Ways of Integration,
Information Processing Systems (Basic Architecture and hardware and Software
trade-offs, Concurrent Design Procedure for Mechatronic Systems
2. System Interfacing, Instrumentation, and Control Systems: Input and output Signals 6
of a Mechatronic System, Signal Conditioning and microprocessor control,
Microprocessor-Based Controllers and Microelectronics, Programmable Logic
Controllers
3. Introduction to Micro- and Nanotechnology, Micro-actuators, Micro-sensors, Nano 10
machines. Modeling Electromechanical Systems: Models for Electromechanical
Systems, Rigid Body Models, Basic Equations of Dynamics of Rigid Bodies, Simple
Dynamic Models, Elastic System Modeling, Dynamic Principles for Electric and
Magnetic Circuits, Earnshaw’s Theorem and Electromechanical Stability
4. The Physical Basis of Analogies in Physical System Models: The Force-Current 6
Analogy: Across and Through Variables, Maxwell’s Force-Voltage Analogy: Effort and
Flow Variables, A Thermodynamic Basis for Analogies
5. Introduction to Sensors and Actuators: Characteristics of Sensor and Actuator Time 6
and Frequency Measurement, The Role of Controls an modelling in Mechatronics:
Integrated Modeling, Design, and Control Implementation, Special Requirements of
Mechatronics that Differentiate from Classic Systems and Control Design, Modeling
as Part of the Design Process, Modeling of Systems and Signals
6. Design Optimization of Mechatronic Systems: Optimization Methods, Principles of 8
Optimization : Parametric Optimization, General Aspects of the Optimization Process,
Types of Optimization Methods, Selection of a Suitable Optimization Method,
Optimum Design of Induction Motor (IM), IM Design Introduction : Classical IM Design,
Use of a Neuron Network for the Identification of the Parameters of a Mechanical
dynamic system, Mechatronics and Computer Modeling and Simulation, Mechatronics
and the Real-Time use of Computers, Communications and Computer Networks,
Control with Embedded Computers and Programmable Logic Controllers
TOTAL 42
11. Suggested Books
1. Mechatronics : an introduction by Robert H Bishop, Taylor & Francis
2 Introduction to Mechatronics by KK Appu Kuttan Oxford University Press
DRAFT EC-88
5. Credits: 4
6. Semester: V
7. Subject Area: UE
9. Objective: To introduce fundamentals of Computer Vision and algorithms for object detection ,
recognition and tracking.
Hours
2. Basics of image processing – Pixel representations histograms ,transforms, 7
colour filters, noise removal,
4. Object Recognition : Object Modeling, Bayesian Classification, Feature Selection 6
and Boosting, Scene and Object Discrimination.
5. Motion and Tracking: Motion detection and tracking of point features, optical flow, 8
SURF, SIFT. Tracking- Kalman filter, Particle Filter, Comparison of deterministic
and probabilistic methods condensation, tracking humans, multi-frame
reconstruction under affine and perspective projection geometry.
6. Introduction to Computer Vision programming libraries: MATLAB/ OpenCV. 8
advantages and disadvantages of each .
TOTAL 42
11. Suggested Books
Publication/
Reprint
1. Computer Vision: A Modern Approach (2nd Edition) 2nd Edition by David A. 2002
Forsyth (Author), Jean Ponce (Author)
2. Learning OpenCV: Computer Vision with the OpenCV Library Gary Bradski, 2008
Adrian Kaehler
DRAFT EC-89
1. Subject Code: EC- 355 Course Title: Embedded Systems
3. Examination Duration (ETE)(Hrs.): Theory 3 Hrs Practical
5. Credits: 4
6. Semester: V
7. Subject Area: UE
Hours
1. Overview of Embedded Systems: Characteristics of Embedded Systems. Comparison 8
of Embedded Systems with general purpose processors. General architecture and
functioning of micro controllers. PIC and 8051 micro controllers : Architecture, memory
interfacing , interrupts, instructions, programming and peripherals .
applications.
3. Digital Signal Processors: DSP Architecture, DSP applications, algorithms, data path, 4
memory, addressing modes, peripherals. TI and Sharc family of DSP processors.
4. System On Chip : Evolution, features, IP based design, TI OMAP architecture and 4
peripherals. Digital Multimedia processor: Architecture and peripherals.
5. SRAM, DRAM working and organization. Interfacing memory with ARM 7. Elements 4
of Network Embedded Systems
6.RTOS : RT-Linux introduction, RTOS kernel, Real-Time Scheduling 10
Bus structure: Time multiplexing, serial, parallel communication bus structure. Bus
arbitration, DMA, PCI, AMBA, I2C and SPI Buses.
TOTAL 42
11. Suggested Books
Year of
Reprint
1. Computers as components: Principles of Embedded Computing System 2000
Design, Wayne Wolf, Morgan Kaufman Publication
2. ARM System Developer’s Guide: Designing and Optimizing System 2004
Software, Andrew N. Sloss, Dominic Symes, Chris Wright, , Morgan
Kaufman Publication
3. Design with PIC Microcontrollers, John B. Peatman, Pearson Education Asia 2002
4. The Design of Small-Scale embedded systems, Tim Wilmshurst, Palgrav 2003

5. Embedded System Design, Marwedel, Peter, Kluwer Publishers 2004
DRAFT EC-90
3. Examination Duration (ETE) (Hrs.): Theory 3 Practical 0
5. Credits: 4
6. Semester: V
7. Subject Area: UE
SNo Contents Contact
Hours
Wiener filtering.
skeletons, pruning.
6. Introduction to various colour models: RGB, CMY, CMYK, HSI, HSV, and YCbCr. 6
Concept of image compression, Image Segmentation: detection of
TOTAL 42
11. Suggested Books
S.N Name of Books / Authors/ Publishers Year of
o. Publication/
Reprint
1. Digital Image Processing/ Gonzalez and Woods/ Pearson Education 2008/Third Edition
2. Fundamentals of Digital Image Processing/ A.K. Jain/ PHI Indian Edition
3. Digital Image Processing using MATLAB/ Gonzalez, Woods, and Eddins/ Second/ 2013
McGraw Hill
4. Digital Image Processing/ K.R. Castleman/ Pearson 2014
DRAFT EC-91
5. Digital Image Processing Algorithms and Applications/I. Pitas/John Wiley 2002
6. Image Processing, Analysis, and Machine Vision/Milan Sonka, Vaclav 4th Edition
Hlavac, Roger Boyale/ Cengage Learning
1. Subject Code: EC -359 Course Title: VLSI Design

5. Credits: 4
6. Semester: V
7. Subject Area: UE

Hours
1. Introduction to VLSI, Manufacturing process of CMOS integrated circuits, CMOS 6
n-well process design rules, packaging integrated circuits, trends in process
technology.
MOS transistor, Energy band diagram of MOS system, MOS under external bias,
2. MOSFET scaling and small geometry effects, MOS capacitances, Modeling of 6
The Wire: Interconnect parameters: capacitance, resistance and inductance.
Electrical wire models: The ideal wire, the lumped model, the lumped RC model,
3. MOS inverters: Resistive load inverter, inverter with n-type MOSFET load, 8
CMOS inverter: Switching Threshold, Noise Margin, Dynamic behavior of CMOS
inverter, computing capacitances, propagation delay, Dynamic power
consumption, static power consumption, energy, and energy delay product
calculations, stick diagram, IC layout design and tools.
Static CMOS Design: Complementary CMOS, Ratioed logic, Pass transistor
logic, BiCMOS logic, pseudo nMOS logic,
Dynamic CMOS logic, clocked CMOS logic CMOS domino logic, NP domino
logic, speed and power dissipation of Dynamic logic, cascading dynamic gates.
6. Pulse registers, sense amplifier based registers, Pipelining, Latch verses 6
Register based pipelines, NORA-CMOS. Two-phase logic structure; VLSI
designing methodology –Introduction, VLSI designs flow, Computer aided
design technology: Design capture and verification tools, Design Hierarchy
Concept of regularity, Modularity & Locality, VLSI design style, Design quality.
TOTAL 42
DRAFT EC-92
11. Suggested Books
Publication/
Reprint
1. Digital integrated circuits a design perspective by Jan M Rabaey, 2011
Anantha Chadrakasan Borivoje Nikolic, Pearson education.
2. CMOS digital integrated circuits by Sung MO Kang Yusuf Leblebici, Tata 2002
McGraw Hill Publication
3. Principle of CMOS VLSI Design by Neil E Weste and Kamran 2000
Eshraghian, Pearson education.
DRAFT EC-93
University Elective Courses
DRAFT EC-94
CO351 ENTERPRISE & JAVA PROGRAMMING
1. Subject Code: CO351 Course Title: Enterprise & Java programming

5. Credits: 3
6. Semester: ODD
7. Subject Area: UEC
9. Objective: To introduce fundamentals of Enterprise Java Programming, concepts of program
development using beans.
Unit Contents Contact Hours

No.
1. Collections : Collection Interfaces, Concrete Collections, Collections Framework. 5

Multithreading : Creating and running thread, Multiple thread synchronization,
Thread communication, Thread group, Thread priorities, Daemon Thread, Life
Cycle ofThread.
2. Fundamentals in Networking: Sockets in Java - Internet Addressing - DNS – 6
Ipv4,IPv6- URL class - TCP/IP and Datagram. The interfaces and classes for
networking :Interfaces and classes of java.net package; InetAddress class : IP
address scope - Host name resolution - Methods of InetAddress class; Program
to look up the IP addresses for a hostname - Factory methods - Creating and using
Sockets : Socket class - constructors and methods of Socket class. Creating TCP
servers &clients : TCP/IP server sockets - Constructors and methods of
ServerSocket class - Program to create a TCP/IP server and client. Handling
URL: URL class - constructors and methods of URL class -URLConnection
class - fields of URLConnection class - methods of URLConnection class.
Working with Datagrams: DatagramPacket - Constructors for DatagramPacket
class - Methods of DatagramPacket class - creating Datagram server and client.
3. JDBC Package :JDBC – JDBC versus ODBC – Types of JDBC drivers – 6
Connection – Statement – PreparedStatement.ResultSet :Fields of ResultSet –
Methods of ResultSet – Executing a query - ResultSetMetaData –
DatabaseMetaData. Datatypes in JDBC : Basic datatypes in JDBC – Advanced
DRAFT EC-95
datatypes in JDBC – fields of Statement – methods of Statement –
CallableStatement Interface – BatchUpdates
4. Servlets : Using Servlets - Servlet Package - Servlet lifecycle - init() method - 7
service() method , doGet() method, doPost() method and destroy() method .
Classes and interfaces of Servlet: Servlet - GenericServlet - ServletConfig -
ServletContext - ServletException - ServletInputStream - ServletOutputStream -
ServletRequest – ServletResponse. Classes and interfaces of HttpServlet:
HttpServlet - HttpServletRequest - HttpServletResponse - Reading HTML form
data from Servlets - Response Headers - Response Redirection. Handling
Servlets : Servlet Chaining - HttpUtils - Database access with JDBC inside
servlet. State and Session management : Cookies - HttpSession - Server Side
includes - Request forwarding – RequestDispatcher.
5. Concepts of Java Beans: Java Beans - Advantage of Java Beans - Reflection and 9
Introspection - Customizers – Persistence. Developing Java Beans : Bean
Developer Kit (BDK) - Creating a Java Bean - Creating a Bean Manifest file -
Creating a Bean JAR file. Controls and Properties of a Bean : Adding controls
to Beans - Giving Bean Properties - BeanInfo interface - SimpleBeanInfo
class. Types of Properties: Design pattern for Properties: Simple properties -
Indexed Properties; Descriptor Classes - Giving Bean methods - Bound and
Constrained Properties - Property Editors.
6. Components of EntrepriseBeans : Distributed Multitiered Applications -J2EE 9

components: J2EE clients, Web components, J2EE containers. Developing an
Enterprise Bean : Packaging - Enterprise JavaBeans Technology - Enterprise
Bean - Contents of an Enterprise Bean. Session Bean : Stateful session bean – life
cycle of stateful session bean - Stateless session bean – life cycle of stateless
session – ejbCreate methods – Business methods – Home interface – Remote
interface – Running the session bean. Entity Bean :Persistence - Bean managed
Persistence - Container Managed Persistance - Shared Access - Primary key –
Relationships. Message Driven Bean :life cycle of message driven bean –
onMessage method.
TOTAL 42
11. Suggested Books
S. No. Name of Books / Authors/ Publishers
DRAFT EC-96
Text Books
1. Java 2 Programming Black Book - Steven Holzner dreamTech Press(ISBN-9788177226553), 2005
2. JavaBeans Programming from the GroundUp - Joseph O’Neil, TMGH, New
Delhi(ISBN- 007463786X), 2001
Reference Books
3 Head first EJB-O’Reilly (ISBN: 8173665265), 2003
4. “Beginning Java™ EE 6 Platform with GlassFish 3 From Novice to Professional” by Antonio
Goncalves– Apress publication(ISBN: 9781430219545), 2009
CO353 E-COMMERCE AND ERP

1. Subject Code: CO353 Course Title: E-Commerce and ERP
5. Credits: 3
6. Semester: ODD
9. Objective: To introduce E-Commerce and ERP

No.
1. Introduction: Definition of Electronic Commerce, E-Commerce: technology and 7

prospects, incentives for engaging in electronic commerce, needs of E-Commerce,
advantages and disadvantages, framework, Impact of E-commerce on business, E-
Commerce Models.
2. Network Infrastructure for E- Commerce: Internet and Intranet based E- 7

commerce- Issues, problems and prospects, Network Infrastructure, Network
Access Equipments, Broadband telecommunication (ATM, ISDN, FRAME
RELAY). Mobile Commerce: Introduction, Wireless ApplicationProtocol, WAP
technology, Mobile Information device.
DRAFT EC-97
3. Web Security: Security Issues on web, Importance ofFirewall, components of 6
Firewall, Transaction security, Emerging client server, Security Threats, Network
Security, Factors to consider in Firewall design, Limitation of Firewalls.
4. Electronic Payments: Overview, The SET protocol, Payment Gateway, certificate, 6

digital Tokens, Smart card, credit card, magnetic strip card, E-Checks,
Credit/Debit card based EPS, online Banking. EDI Application in business, E-
Commerce Law, Formsof Agreement, Govt. policies and Agenda.
5. ERP Introduction, Benefits, Origin, Evolution and Structure:Conceptual Model of 8

ERP, The Evolution of ERP, The Structure of ERP. Business Process
Reengineering, Data ware Housing, Data Mining, Online Analytic
Processing(OLAP), Product Life Cycle Management(PLM),LAP, Supply chain

Management.
6. ERP Marketplace and Marketplace Dynamics:Market Overview, Marketplace 8

Dynamics, The Changing ERP Market. ERP- Functional Modules: Introduction,
Functional Modules of ERP Software, Integration of ERP, Supply chain and
Customer Relationship Applications. ERP Implementation Basics, ERP
Implementation Life Cycle, Role of SDLC/SSAD, Object Oriented Architecture,
Consultants, Vendors and Employees, ERP & E-Commerce, Future Directives- in
ERP, ERP and Internet.
TOTAL 42
11. Suggested Books
1. Goel, Ritendra “E-commerce”, New Age International,2007
2. Ravi Kalakota, Andrew Winston, “Frontiers of Electronic Commerce”, Addison- Wesley. 1996
3. Vinod Kumar Garg and Venkitakrishnan N K, “Enterprise Resource Planning –
Concepts and Practice”, PHI 2004
4. Rahul V. Altekar “Enterprise Resource Planning”, Tata McGraw Hill, 2004
5. Alexis Leon, “ERP Demystified”, Tata McGraw Hill, 2014
DRAFT EC-98
CO355 CRYPTOGRAPHY AND INFORMATION SECURITY
1. Subject Code: CO355 Course Title: Cryptography and Information Security
5. Credits: 3
6. Semester: ODD
9. Objective: To study various cryptographic techniques, mathematics related to cryptography and
some network security protocols.

No.
1. Introduction: Need for security, Introduction to security attacks, services and 6

mechanism, introduction to cryptography, Conventional Encryption: Conventional
encryption model, classical encryption techniques- substitution ciphers and
transposition ciphers, cryptanalysis, stereography, stream and block ciphers, Intruders,
Viruses and related threads.
2. Modern Block Ciphers: Block ciphers principals, Shannon’s theory of confusion and 6
diffusion, Fiestal structure, data encryption standard(DES), strength of DES, crypt
analysis of DES, block cipher modes of operations, triple DES, IDEA encryption and
decryption, strength of IDEA, key distribution.
3. Introduction to graph, ring and field, prime and relative prime numbers, modular 8
arithmetic, Fermat’s and Euler’s theorem, primarily testing, Euclid’s Algorithm,
Chinese Remainder theorem, discrete logarithms, Principals of public key crypto
systems, RSA algorithm, security of RSA, key management, Diffle-Hellman key
exchange algorithm, introductory idea of Elliptic curve cryptography, Elganel
encryption
4. Message Authentication and Hash Function: Authentication requirements, 6

authentication functions, message authentication code (MAC), hash functions,
security of hash functions and MACS, MD5 message digest algorithm, Secure hash
algorithm(SHA), Public Key Infrastructure(PKI): Digital Certificate, private key
management, Digital Signatures: Digital Signatures, authentication protocols, digital
signature standards (DSS), proof of digital signature algorithm.
DRAFT EC-99
5. Authentication Applications: Kerberos and X.509, directory authentication service, 8
password, challenge-response, biometric authentication, electronic mail security-
pretty good privacy (PGP), S/MIME.
6. IP Security: Architecture, Authentication header, Encapsulating security payloads, 8

combining security associations, key management.
Web Security: Secure Socket Layer(SSL) and transport layer security, TSP, Secure
Electronic Transaction (SET), Electronic money, WAP security, firewall design
principals, Virtual Private Network (VPN) security.
TOTAL 42
11. Suggested Books
1. William Stallings, “Cryptography and Network Security: Principals and Practice”, Prentice Hall, New
Jersy. 2016
2. Atul Kahate, “Cryptography and Network Security”, TMH. 2009
3. Behrouz A. Forouzan, “Cryptography and Network Security”, TMH.2007
4. Johannes A. Buchmann, “Introduction to Cryptography”, Springer-Verlag. 2004
5. Bruce Schiener, “Applied Cryptography”. 2015
CO357 OPERATING SYSTEM

1. Subject Code: CO357 Course Title: Operating System
5. Credits: 3
6. Semester: ODD
9. Objective: To familiar with the fundamental principles of the operating system, its services and
functionalities, the concepts of processes, synchronization and scheduling, memory management and need
for protection in computer systems
DRAFT EC-100
No.
1. Introduction: Operating system and function, Evolution of operating 4

system, Batch, Interactive, Time Sharing and Real Time System, System
protection.
Operating System Structure: System Components, System structure,

Operating System Services.
2. Concurrent Processes: Process concept, Principle of Concurrency, Producer 9

Consumer Problem, Critical Section problem, Semaphores, Classical
problems in Concurrency, Inter Process Communication, Process Generation,
Process Scheduling.
CPU Scheduling: Scheduling Concept, Performance Criteria of Scheduling

Algorithm, Evolution, Multiprocessor Scheduling.
3. Deadlock: System Model, Deadlock Characterization, Prevention, Avoidance 8

and Detection, Recovery from deadlock combined approach.
4. Memory Management: Base machine, Resident monitor, Multiprogramming 9

with fixed partition, Multiprogramming with variable partition, Multiple base
register, Paging, Segmentation, Virtual memory concept, Demand paging,
Performance, Paged replacement algorithms, Allocation of frames, Thrashing,
Cache memory organization, Impact on performance.
5. I/O Management & Disk Scheduling: I/O devices and organization of I/O 9
function, I/O Buffering, DISK I/O, Operating System Design Issues.
File System: File Concept, File Organization and Access Mechanism, File
Directories, File Sharing, Implementation Issues
6. Case Studies: Windows, Linux and Unix 3
TOTAL 42
11. Suggested Books

Text Books
1. Silbersachatz and Galvin, “Operating System Concepts”, Pearson, 5th Ed, 2001
2. Tannenbaum, “Operating Systems”, PHI, 4th Edition, 2000
Reference Books
DRAFT EC-101
3. Milenekovic, “Operating System Concepts”, McGraw Hill 2001
4. Dietel, “An introduction to operating system”, Addison Wesley 1983
CO359 INTELLECTUAL PROPERTY RIGHTS

1. Subject Code: CO359 Course Title: Intellectual Property Rights
3. Examination Duration (ETE )(Hrs.): Theory 3Hrs Practical 0
5. Credits: 3
6. Semester: ODD
9. Objective:To familiarize the students with basic concepts in each type of IPR together with historical
developments in the subject & its importance in modern times.
Unit Contents Contact

No. Hours
1. Introduction: Concept of IPR, Historical development , kinds of IPR,brief 5

description of patent, trademark, copyright ,industrial design, importance of IPR,
IPR authorities.
2. PATENTS :Introduction, Indian Patent Act 1970 &2002, Protectable subject 8
matter--patentable invention, Procedure for obtaining patent, Provisional and
complete specification Rights conferred on a patentee, transfer of patent,
Revocation and surrender of patents, Infringement of patents, Action for
infringement, Patent agents, Patent in computer programs.
3. Trademark: Introduction, Statutory authorities, principles of registration of 7
trademarks, rights conferred by registration of trademarks, Infringement of
trademarks and action against infringement, procedure of registration and
duration,licensing in trademark
4. Copyright: Introduction, Author and ownership of copyright, rights conferred by 7
copyright,term of copyright, assignment/licence of copyright, Infringement of
copyright ,remedies against infringement of copyright, registration of copyright,
copyright enforcement and societies
DRAFT EC-102
5. Industrial design: The design act-2000, registerability of a design, procedure of 6
registration of a design, piracy of a registered design, Case law on designs
6. International IPR & case laws: World intellectual property organization, WCT, 9
WPPT, TRIPS, Copyright societies, international IPR dispute resolution
mechanism. Case laws.
TOTAL 42
11. Suggested Books
Textbooks:
1. Law Relating to Intellectual property, fourth edition by B.L.Wadehra .Universal law
publishing co. pvt. Ltd , 2007. ISBN 978-81-7534-588-1
Reference books:
2. Intellectual property: Patents, copyright ,trademarks and allied rights. Fifth edition by W.R.
Cornish. Sweet & Maxwell publisher, 2003. ISSN 9780421781207
3 Law and practice of intellectual property in India by VikasVashishth, 2006
ISBN: 81-7737-119-3
4 Patents ,copyrights, trade marks and design by B L Wadhera, 2014
5 Dr. B. L. Wadhera, “Intellectual Property Law Handbook”. Universal Law Publishing, 2002.
CO361 DATABASE MANAGEMENT SYSTEM
1. Subject Code: CO361 Course Title: Database Management System

5. Credits: 3
6. Semester: ODD
9. Objective: To provide knowledge about the principles, concepts and applications of Database
Management System.
DRAFT EC-103

No.
1. Introduction: Data base system concepts and its architecture, Data models schema 7
and instances, Data independence and data base language and interface, Data
definition languages, DML. Overall data base structure.
Data modeling using Entity Relationship Model: E.R. model concept, notation
for ER diagrams mapping constraints, Keys, Concept of super key, candidate key,
primary key generalizations, Aggregation, reducing ER diagrams to tables, extended
ER model.
2. Relational Data Model and Language: Relational data model concepts, integrity 7
constraints, Keys domain constraints, referential integrity, assertions, triggers,
foreign key relational algebra, relational calculus, domain and tuple calculus, SQL
data definition queries and updates in SQL.
3. Data Base Design: Functional dependencies, normal forms, 1NF, 2NF, 3NF and 6
BCNF, multi-valued dependencies fourth normal forms, join dependencies and fifth
normal forms. Inclusion dependencies, loss less join decompositions, normalization
using FD, MVD and JDs, alternatives approaches to database design.
4. File Organization, Indexing and Hashing Overview of file organization 8
techniques,
Indexing and Hashing- Basic concepts, Static Hashing, Dynamic Hashing, Ordered
indices, Multi-level indexes, B-Tree index files, B+- Tree index files, Buffer
management
Transaction processing concepts: Transaction processing system, schedule and
recoverability, Testing of serializability, Serializability of schedules, conflict &
view serializable schedule, recovery from transaction failures, deadlock handling.
5. Concurrency Control Techniques: Locking Techniques for concurrency control, 8
time stamping protocols for concurrency control, concurrency control in distributed
systems. multiple granularities and multi-version schemes.
6 Case Studies: Commercial databases, Oracle, Postgress, MySQL 6
TOTAL 42
11. Suggested Books
Text Books
1 Elmasri, Navathe,”Fundamentals of Database systems”, Addision Wesley, 2016
2 Korth, Silberchatz, Sudarshan,”Data base concepts”, McGraw-Hill. 2010
DRAFT EC-104
Reference Books
1. Ramakrishna, Gehkre, “Database Management System”, McGraw-Hill 2014
2. Date C.J.,”An Introduction to Database systems” 2006
EC351 MECHATRONICS
1. Subject Code: EC351 Course Title: Mechatronics
5. Credits: 4
6. Semester: V
9. Objective: To introduce fundamentals of Mechatronics
No. Hours
1. Introduction : Basic Definitions and key elements of Mechatronics, Mechatronic 6
Design Approach: Functions of Mechatronic Systems, Ways of Integration,
Information Processing Systems (BasicArchitecture and hardware and Software
trade-offs, Concurrent Design Procedure for Mechatronic Systems
2. System Interfacing, Instrumentation,and Control Systems: Input and output Signals 6
of a Mechatronic System, Signal Conditioning and microprocessor control,
Microprocessor-Based Controllers and Microelectronics, Programmable Logic
Controllers
3. Introduction to Micro- and Nanotechnology, Micro-actuators, Micro-sensors, 10
Nanomachines. Modeling Electromechanical Systems: Models for Electromechanical
Systems, Rigid Body Models, Basic Equations of Dynamics of Rigid Bodies, Simple
Dynamic Models, Elastic System Modeling, Dynamic Principles for Electric and
Magnetic Circuits, Earnshaw’s Theorem and Electromechanical Stability
4. The Physical Basis of Analogies in Physical System Models: The Force-Current 6
Analogy: Across and Through Variables, Maxwell’s Force-Voltage Analogy:Effort
and Flow Variables, A Thermodynamic Basis for Analogies
5. Introduction to Sensors and Actuators: Characteristics of Sensor and Actuator Time 6
and Frequency Measurement, The Role of Controls an modelling in Mechatronics:
Integrated Modeling, Design, and Control Implementation, Special Requirements of
Mechatronics that Differentiate from Classic Systems and Control Design, Modeling
as Part of the Design Process, Modeling of Systems and Signals
6. Design Optimizationof Mechatronic Systems: Optimization Methods, Principles of 8
Optimization : ParametricOptimization, General Aspects of the OptimizationProcess,
Types of Optimization Methods, Selection of aSuitable Optimization Method,
Optimum Design of Induction Motor (IM), IM Design Introduction : Classical IM
Design, Use of a Neuron Network for the Identification ofthe Parameters of a
DRAFT EC-105
Mechanical dynamic system, Mechatronics and Computer Modelingand Simulation,
Mechatronics and the Real-Time useof Computers, Communications andComputer
Networks,Control withEmbedded Computersand ProgrammableLogic Controllers
TOTAL 42
11. Suggested Books

1. Mechatronics : an introduction by Robert H Bishop, Taylor & Francis, 2005
2 Introduction to Mechatronics by KK AppuKuttan Oxford University Press, 2007
EC353 COMPUTER VISION

5. Credits: 4
6. Semester: V
9. Objective: To introduce fundamentals of Computer Vision and algorithms for object detection,
recognition and tracking.

No. Hours
2. Basics of image processing – Pixel representations histograms ,transforms, colour 7
filters, noise removal,
4. Object Recognition : Object Modeling, Bayesian Classification, Feature 6
Selection and Boosting, Scene and Object Discrimination.
5. Motion and Tracking: Motion detection and tracking of point features, optical 8
flow, SURF, SIFT. Tracking- Kalman filter, Particle Filter, Comparison of
DRAFT EC-106
deterministic and probabilistic methods condensation, tracking humans, multi-
frame reconstruction under affine and perspective projection geometry.
6. Introduction to Computer Vision programming libraries: MATLAB/OpenCV. 8
advantages and disadvantages of each .
TOTAL 42
11. Suggested Books

1. Computer Vision: A Modern Approach (2nd Edition) 2nd Edition by David A.
Forsyth (Author), Jean Ponce (Author), 2002
2. Learning OpenCV: Computer Vision with the OpenCVLibrary Gary Bradski,
Adrian Kaehler, 2008
EC355 EMBEDDED SYSTEM
1. Subject Code: EC- 355 Course Title: Embedded Systems

5. Credits: 4
6. Semester: V

No. Hours
1. Overview of Embedded Systems: Characteristics of Embedded Systems. Comparison 8
of Embedded Systems with general purpose processors. General architecture and
functioning of micro controllers. PIC and 8051 micro controllers : Architecture,
memory interfacing , interrupts, instructions, programming and peripherals .
applications.
3. Digital Signal Processors: DSP Architecture, DSP applications, algorithms, data path, 4
memory, addressing modes, peripherals. TI and Sharc family of DSP processors.
4. System On Chip : Evolution, features, IP based design, TI OMAP architecture and 4
peripherals. Digital Multimedia processor: Architecture and peripherals.
5. SRAM, DRAM working and organization. Interfacing memory with ARM 7. 4
Elements of Network Embedded Systems
6. RTOS : RT-Linux introduction, RTOS kernel, Real-Time Scheduling 10
Bus structure: Time multiplexing, serial, parallel communication bus structure. Bus
arbitration, DMA, PCI, AMBA, I2C and SPI Buses.
TOTAL 42
DRAFT EC-107
11. Suggested Books

1. Computers as components: Principles of Embedded Computing System Design, Wayne Wolf,
Morgan Kaufman Publication, 2000
2. ARM System Developer’s Guide: Designing and Optimizing System Software, Andrew N.
Sloss, Dominic Symes, Chris Wright, , Morgan Kaufman Publication, 2004
3. Design with PIC Microcontrollers, John B. Peatman, Pearson Education Asia, 2002
4. The Design of Small-Scale embedded systems, Tim Wilmshurst, Palgrav, 2003
5. Embedded System Design, Marwedel, Peter, Kluwer Publishers, 2004
EC357 DIGITAL IMAGE PROCESSING

3. Examination Duration (ETE) (Hrs.): Theory 3Hrs Practical 0
5. Credits: 4
6. Semester: V
No. Hours
DRAFT EC-108
Wiener filtering.
skeletons, pruning.
6. Introduction to various colour models: RGB, CMY, CMYK, HSI, HSV, and 6
YCbCr. Concept of image compression, Image Segmentation: detection of
TOTAL 42
11. Suggested Books

1. Digital Image Processing/ Gonzalez and Woods/ Pearson Education, 2008/Third Edition
2. Fundamentals of Digital Image Processing/ A.K. Jain/ PHI, Indian Edition
3. Digital Image Processing using MATLAB/ Gonzalez, Woods, and Eddins/ McGraw Hill,
Second/ 2013
4. Digital Image Processing/ K.R. Castleman/ Pearson, 2014
5. Digital Image Processing Algorithms and Applications/I. Pitas/John Wiley, 2002
6. Image Processing, Analysis, and Machine Vision/Milan Sonka, Vaclav Hlavac, Roger
Boyale/ Cengage Learning, 4th Edition
EC359 VLSI DESIGN
1. Subject Code: EC -359 Course Title: VLSI Design

5. Credits: 4
6. Semester: V
DRAFT EC-109
.No. Hours
1. Introduction to VLSI, Manufacturing process of CMOS integrated circuits, 6
CMOS n-well process design rules, packaging integrated circuits, trends in
process technology.
MOS transistor, Energy band diagram of MOS system,MOS under external bias,
2. MOSFET scaling and small geometry effects, MOScapacitances, Modeling of 6
The Wire: Interconnect parameters: capacitance, resistanceand inductance.
Electrical wire models: The ideal wire, the lumpedmodel, the lumped RC model,
3. MOS inverters: Resistive load inverter, inverter with n-type MOSFET load, 8
CMOS inverter: Switching Threshold, Noise Margin, Dynamic behavior of
CMOS inverter, computing capacitances, propagation delay, Dynamic power
consumption, static power consumption, energy, and energy delay product
calculations, stick diagram, IC layout design and tools.
Static CMOS Design: Complementary CMOS, Ratioedlogic, Pass transistor
logic, BiCMOS logic, pseudo nMOS logic,
Dynamic CMOS logic, clocked CMOS logic CMOS domino logic, NP domino
logic, speed and power dissipation of Dynamic logic, cascading dynamic gates.
6. Pulse registers, sense amplifier based registers, Pipelining, Latch verses Register 6
based pipelines, NORA-CMOS. Two-phase logic structure; VLSI designing
methodology –Introduction, VLSI designs flow, Computer aided design
technology: Design capture and verification tools, Design Hierarchy Concept of
regularity, Modularity & Locality, VLSI design style, Design quality.
TOTAL 42
11. Suggested Books

1. Digital integrated circuits a design perspective byJan M Rabaey, Anantha Chadrakasan
Borivoje Nikolic, Pearson education, 2011.
2. CMOS digital integrated circuits by Sung MO KangYusuf Leblebici, Tata McGraw Hill
Publication, 2002
3. Principle of CMOS VLSI Design by Neil E Weste and Kamran Eshraghian, Pearson
education, 2000.
DRAFT EC-110
EE351 POWER ELECTRONIC SYSTEMS
1. Subject Code: EE-351 Course Title: Power Electronic Systems

2. Contact Hours : L: 3 T: 0 P: 0
3. Examination Duration (Hrs.) : Theory: 3 Practical: 0
4. Relative Weight CWS: 25 PRS: 0 MTE: 25 ETE: 50 PRE: 0
5. Credits: 3
6. Semester: VIII
8. Pre-requisite: EE-203, EE-301
9. Objective:To familiarize the students with power electronics and its applications.
No.
1. Solid State Power Devices: Principle of operation of SCR, dynamic 8

characteristic of SCR during turn ON and turn OFF, parameters of SCR,
dv/dt and di/dt protection, snubber circuit, commutation circuits; Principle
of operation ofMOSFET, IGBT, GTO, MCT, SIT, SITH, IGCT, their
operating characteristics.
2. Single-phase Converter: Half wave converter, 2-pulse midpoint converter, 8
half controlled and fully controlled bridge converters, input current and
output voltage waveforms, effect of load and source impedance, expressions
for input power factor, displacement factor, harmonic factor and output
voltage, effect of free-wheeling diode, triggering circuits.
Three-phase Converter: Half wave, full wave, half controlled and fully
controlled bridge converters, effect of load and source impedance,
expressions for input power factor, displacement factor, harmonic factor and
output voltage,
3. AC-AC Converters: Principle of operation of cycloconverter, waveforms, 4
control technique; Introduction of matrix converter.
4. DC-DC Converters: Principle of operation of single quadrant chopper, 4

continuous and discontinuous modes of operation; Voltage and current
commutation, design of commutating components; Introduction to SMPS.
5. Inverters: Voltage source and current source inverters, Principle of 8

operation of single-phase half bridge and full bridge voltage source
inverters, voltage and current waveforms; Three-phase bridge inverter, 1200
DRAFT EC-111
and 1800 modes of operation, voltage and current waveforms with star and
delta connected RL load; Voltage and frequency control of inverters; PWM
techniques-single pulse, multiple pulse, selective harmonic elimination,
sinusoidal PWM.
6. Applications: 10
FACTS Technology: Reactive power control in power systems,

transmission system compensation, static series and shunt compensation,
static shunt and series compensators- SVC, STATCOM, TCSC, SSSC and
their working principles and characteristics. Combined series-shunt
compensators –UPFC and its applications and characteristic.
VSC-HVDC Systems: Principles and applications
Total 42
S. No. Name of Authors /Books / Publishers
1. Mohan N., Undeland T. M. and Robbins W. P., “Power Electronics-Converters, Applications

and Design”, 3rd Ed., Wiley India, 2002.
2. Rashid M. H., “Power Electronics Circuits Devices and Applications”, 3rd Ed., Pearson
Education, 2004.
3. N.G. Hingorani and L. Gyugyi, “Understanding FACTS”, IEEE Press, 2000
4. K.R. Padiyar, “Facts Controllers In Power Transmission and Distribution”, New Age
publishers, 2013
5. HVDC power transmission system, K.R.Padiyar, NewAge Publishers,2011
EE353 ELECTRICAL MACHINES AND POWER SYSTEMS
1. Subject Code: EE-353 Course Title: Electrical Machines and Power Systems
DRAFT EC-112
5. Credits: 3
6. Semester: VIII
8. Pre-requisite: EE-208, EE-303, EE-304
9. Objective:To familiarize the students with electrical machines and power systems.

No.
1 8
Transformers : constructional features, types, Special constructional
features – cruciform and multiple stepped cores, cooling methodology,
conservators, breather, Buchholz relay, voltage, current and impedance
relationships, equivalent circuits andphasor diagrams at no load and full
load conditions,voltage regulation, losses and efficiency, all day efficiency,
auto transformer and equivalent circuit, parallel operation and load sharing.
2 Asynchronous machines: General constructional features of poly phase 8
asynchronous motors, concept of rotating magnetic field, principle of
operation, phasor diagram, Equivalent circuit, torque and power
equations, torque-slip characteristics, losses and efficiency.
3 Synchronous machines : General constructional features, armature 9
winding, emf equation, effect of distribution and pitch factor,flux and
mmf relationship, phasor diagram, non-salient pole machine, equivalent
circuit, determination of equivalent circuit parameters by open and short
circuit tests, voltage regulation using synchronous impedance method,
power angle characteristics
4 Single line diagram of power system, brief description of power system 9

elements, synchronous machine, transformer, transmission line, bus bar,
circuit breaker and isolator. Supply System:different kinds of supply
system and their comparison, choice of transmission voltage.
Transmission Lines:configurations, types of conductors, resistance of line,
skin effect
5 Transmission lines: Calculation of inductance and capacitance of single 8
phase, three phase, single circuit and double circuit ,transmission lines,
representation and performance of short, medium and long transmission
lines, Ferranti effect,surge impedance loading.
Total 42
DRAFT EC-113
11.Suggested Books
1 Fitzgerald. A.E., Charles KingselyJr, Stephen D.Umans, ‘Electric Machinery’, Tata McGraw
Hill, 2006.
2 M.G. Say, ‘Performance and Design of Alternating Current Machines’, CBS Publishers, New
Delhi, 2008
3 Nagrath I. J and Kothari D.P. ‘Electric Machines’, Tata McGraw Hill Publishing Company Ltd,
2010.
4 Power System Analysis, J. Grainger and W.D. Stevenson, TMH, 2006.
5 Electrical Power Systems,C. L.Wadhwa, New age international Ltd. Third Edition, 2010
6 Electric Power Generation, Transmission&Distribution,S.N.Singh, PHI Learning, 2008.
EE-355 INSTRUMENTATION SYSTEMS
1. Subject Code: EE-355 Course Title: Instrumentation Systems

5. Credits: 3
6. Semester: VIII
9. Objective:To familiarize the students with instrumentation systems.

No.
1 Transducers-I:Definition, advantages of electrical transducers, 8

classification, characteristics, factors affecting the choice of transducers,
strain gauges, resistance thermometer, thermistors, thermocouples, LVDT,
RVDT
DRAFT EC-114
2 Transducers-II:Capacitive, piezoelectric, Hall effect and opto electronic 8
transducers. measurement of motion, force, pressure, temperature flow and
liquid level.
3 Telemetry:General telemetry system, land line & radio frequency 8

telemetering system, transmission channels and media, receiver &
transmitter. Data Acquisition System:A/D and D/A converters, analog data
acquisition system, digital data acquisition system, modern digital data
acquisition system and signal conditioning.
4 Display Devices and RecordersDisplay devices, storage oscilloscope, DSO, 8

spectrum analyzer, digital recorders.RecentDevelopments:Introduction to
virtual and intelligent instrumentation, fibre optic transducers, smart
sensors, smart transmitters, process instrumentation diagrams.
5 Programmable Logic Controllers :Evolution of PLC-sequential and 10

programmable controllers, architecture and programming of PLC, relay
logic and ladder logic, functional blocks, communication networks for
PLC, field bus, profi-bus, mod-bus
Total 42
1 Electronic Instrumentation and Measurement Techniques, W.D. Cooper and A.D. Helfrick,
Prentice Hall International, 2009.
2 Measurement Systems Application and Design Ernest Doebelin, McGraw- Hill Higher
Education, 5th edition , 2003
3 Instrumentation, Measurement and Analysis, B.C. Nakra& K. Chaudhry, Tata McGraw Hill, 2 nd
Edition, 2001.
4 Advanced Measurements and Instrumentation, A.K. Sawhney, DhanpatRai& Sons, 2010
5 Process Control Instrumentation Technology, Curtis D. Johnson, Pearson, 6th edition, 1999
6 Programmable Logic Controllers, Frank D. Petruzella McGraw-Hill Higher Education, 4th

edition, 2010
DRAFT EC-115
EE357 UTILIZATION OF ELECTRICAL ENERGY
1. Subject Code: EE-357 Course Title: Utilization of Electrical Energy

5. Credits: 3
6. Semester: VIII
9. Objective: To familiarize the students with the concept of electrical power, energy and its utilization.

No.
1. Illumination: Definition:- Luminous flux, solid angle, luminous intensity, 10

illumination, luminous efficiency, depreciation factor, coefficient of utilization,
space to height ratio, reflection factor, glare, shadow, lux. Nature of light, visibility
spectrum curve of relative sensitivity of human eye and wave length of light,
Review of laws of illumination, Different types of lighting sources and their use in
domestic, street and industrial lighting, Energy considerations. LED’s and their
driving circuits.
2 Electric Heating : Advantages of electrical heating, Heating methods: Resistance 08

heating – direct and indirect resistance heating, properties of resistance heating
elements, Induction heating; principle of core type and coreless induction furnace,
Electric arc heating; direct and indirect arc heating, construction, working and
applications of arc furnace, Dielectric heating, applications in various industrial
fields, Infra-red heating and its applications, Microwave heating
3. Electric Welding: Introduction to electric welding, Welding methods, Principles 08

of resistance welding, types – spot, projection seam and butt welding and welding
equipment used, Principle of arc production, electric arc welding, characteristics
of arc, Design of Power supply and welding control circuit, comparison between
AC and DC arc welding, welding control.
4. Electrolytic Processes: Need of electro-deposition laws of electrolysis, process of 08

electro-deposition - clearing, operation, deposition of metals, polishing, buffing
equipment and accessories for electroplating factors affecting electro-deposition ,
principle of galvanizing and its applications, anodising and its applications,
DRAFT EC-116
electroplating on non-conducting materials, manufacture of chemicals by
electrolytic process, electrolysis for water purification
5. Refrigeration and Air Conditioning and Water Coolers: Principle of air 08

conditioning, vapour pressure, refrigeration cycle, eco-friendly refrigerants,
description of electrical circuit used in a) refrigerator, b) air-conditioner, and c)
water cooler, variable speed drive for compressors, high speed compressors, insta-
chill, Peltier effect, thermoelectric cooling, sterling engines, solar concentrator
heating and cooling,
Total 42
11. Suggested books:
1. Dubey G. K., “Fundamentals of Electric Drives”, 2nd Ed., Narosa Publishing House,2007.
2. Taylor E. O., “Utilization of Electric Energy (in SI units)”, Orient Longman, Revised in S.I. units by Rao,
V.V.L,1999
3. Hancock N. N., “Electric Power Utilisation”, Wheelers,1979.
EE-359 NON-CONVENTIONAL ENERGY SYSTEMS

1. Subject Code: EE-359 Course Title: Non-conventional Energy Systems
5. Credits: 3
6. Semester: VIII
9. Objective: To familiarize the students with the non-conventional sources of energy and their integration
to the grid.
DRAFT EC-117

No.
1 Introduction to Non Conventional Energy Systems 10
Various non-conventional energy resources Introduction, availability,

classification, relative merits and demerits. Solar Cells: theory of solar cells,
solar cell materials, solar cell array, solar cell power plant, limitations. Solar
Thermal Energy: solar radiation, flat plate collectors and their materials,
applications and performance, focusing of collectors and their materials,
applications and performance, solar thermal power plants, thermal energy
storage for solar heating and cooling, limitations.
2 Geothermal Energy 8
Resources of geothermal energy, thermodynamics of geo-thermal energy
conversion, electrical conversion, non-electrical conversion,environmental
considerations. Magneto-hydrodynamics (MHD):principle of working of
MHD power plant, performance and limitations.
3 Fuel Cells: Basic principle of working, various types of fuel cells, 8
performance and limitations.
4 Thermo-electrical and thermionic conversions 8
Principle of working of thermo-electrical and thermionic conversions,
performance and limitations. Wind energy: wind power and its sources, site
selection criteria, momentum theory, classification of rotors, concentrations
and augments, wind characteristics, performance and limitations of wind
energy conversion systems.
5 Energy from Bio-mass, Ocean Thermal, Wave and bio-waste 8
Availability of bio-mass and its conversion principles, ocean thermal
energy conversion principles, performance and limitations, wave and tidal
energy conversion principles, performance and limitations, bio-waste
recycling power plants.
42
11. Suggested books:
1 Renewable Energy Resources, John Twidell, Tony Weir, Taylor and Francis, 2nd edition,2005.
2 Solar Engineering of Thermal Processes,John A. Duffie, William A. Beckman, John Wiley &
Sons, 4th edition,2013.
3 Biofuels, Solar and Wind as Renewable Energy Systems: Benefits and Risks,D. Pimentel,
Springer,1st edition,2010.
DRAFT EC-118
4 Solar Photovoltaic Technology and Systems: A Manual for Technicians, Trainers and
Engineers,Chetan Singh Solanki, PHI Learning,2013.
5 Non Conventional Energy Resources, D.S. Chauhan, New Age International Pvt Ltd.,2006
EE-361 EMBEDDED SYSTEMS

1. Subject Code: EE-361 Course Title: Embedded Systems
5. Credits: 3
6. Semester: VIII
9. Objective:To familiarize the students with the concepts of embedded systems.

No.
1. Embedded Processing – Evolution, Issues and Challenges; 1
2 System and Processor Architecture : von Neumann, Harvard and their 2

variants
3 Memory Architecture and Devices; Input-Output Devices and Mechanisms 5
4 Instruction Set and Addressing Modes, Interfacing of Memory and 6

Peripheral Devices – Functional and Timing Issues
5 Application Specific Logic Design using Field Programmable Devices and 2

ASICs
6 Analog to Digital and Digital to Analog Converters 2
7 Bus I/O and Networking Considerations, Bus and Wireless Protocols 4
8 Embedded Systems Software : Constraints and Performance Targets 2
9 Real-time Operating Systems : Introduction, Scheduling in Real-time 4

Operating Systems
DRAFT EC-119
10 Memory and I/O Management : Device Drivers 2
11 Embedded Software Development : Flow, Environments and Tools 2
12 System Specification and Modelling 2
13 Programming Paradigms 2
14 System Verification 2
15 Performance Analysis and Optimisation : Speed, Power and Area 4

Optimisation, Testing of Embedded Systems
Total 42
1. S. Heath, “Embedded Systems Design”, Elsevier India,2005
2. M. Ben-Ari, “Principles of Concurrent and Distributed Programming”, Pearson,2005
3. Jane Liu, “Real Time Systems”, Pearson,2002
EN-351 ENVIRONMENTAL POLLUTION AND E –WASTE

MANAGEMENT
1. Subject Code: EN-351 Course Title: Environmental Pollution & E- Waste Management
3. Examination Duration (ETE) (Hrs.): Theory: 3 Hrs. Practical: 0
5. Credits: 3
6. Semester:VI
9. Objective: The overall aims of the course are for students to acquire understanding of the new and
emerging contaminants from various industrial processes and their transformation products. Studying
emerging environmental issues related to newer methods of manufacture of industrial products.
DRAFT EC-120

No. Hours
1 UNIT-I 9
New and emerging pollutants and related transformation products, Effects & risks
of emerging contaminants on ecosystems and humans, Persistent pollutants.
Analytical methods for identifying emerging pollutants and the products of their
transformation
2 UNIT-II 9
Micro pollutants- Pesticides, Pharmaceutical - Veterinary and human drugs,

personal care products, Surfactants and surfactant metabolites, Flame retardants,
Industrial additives and agents.Emerging pollutants’ toxicity, and their water-
related characteristics (degradability, solubility, sorption…)
3 UNIT-III 8
Emerging Issues - E-waste, Hazardous Waste, Nuclear Waste, Nano pollution,

Thermal Pollution, pollutant emission and treatment
4 UNIT-IV 8
Emerging pollutants’ emergence and fate in surface and ground water, as well as
mathematical modelling, Sustainable Development, Risk mitigation
5 UNIT-V 8
Transformation Products of Emerging Contaminants in the Environment, Removal

of emerging contaminants from water, soil and air, methods and preventive
measures.
Course Outcome:
1. Introduction to new and emerging contaminants and their transformation products.

2. Study of pollutants from manufacturing of goods.
3. Emerging area in environmental pollution.
4. Study of life cycle of a contaminant, modeling and mitigation.
11.Suggested Books:
DRAFT EC-121
1. G. Buttiglieri, T.P. Knepper, (2008), Removal of emerging contaminants in Wastewater
Treatment: Conventional Activated sludge Treatment, Springer-Verlag Berlin Heidelberg,
HdbEnvChem, vol. 5, Part S/2:1-35, DOI: 10.1007/698_5_098
2. Alok Bhandari; Rao Y. Surampalli; Craig D. Adams; Pascale Champagne; Say Kee Ong; R.
D. Tyagi; and Tian Zhang, Eds., (2009) Contaminants of Emerging Environmental Concern,
American Society of Civil Engineers, ISBN (print): 978-0-7844-1014-1, ISBN (PDF): 978-0-
7844-7266-8
3. Dimitra A. Lambropoulou, Leo M. L. Nollet Eds. () Transformation Products of Emerging

Contaminants in the Environment: Analysis, Processes, Occurrence, Effects and Risks, 1st
Edition, Wiley, ISBN-13: 978-1118339596, ISBN-10: 1118339592
EN353 OCCUPATIONAL HEALTH AND SAFETY

MANAGEMENT
1. Subject Code: EN- 353 Course Title: Occupational Health and Safety Management
3. Examination Duration (ETE) (Hrs.): Theory 3 Hrs
5. Credits: 3
6. Semester: V
7. Subject Area: UEC 8.
8. Prerequisite: Nil
9. Course Objectives:
1. Introduction about occupational health and related issues.

2. To give a basic idea about environmental safety management, industrial hygiene.
3. To introduce about training cycle, chemical hazards and control measures.
4. To aware and provide knowledge about ergonomics and different disorders.
5. To provide knowledge about different standards related to safety and health.
10. Detail of Course:

no.
DRAFT EC-122
1 UNIT –I 8
Definition of Occupational Health as per WHO/ILO. Occupational Health
and Environmental Safety Management – Principles practices. Common
Occupational diseases: Occupational Health Management Services at the
work place. Pre-employment, periodic medical examination of workers,
medical surveillance for control of occupational diseases and health records.
2 UNIT –II 8
Occupational Health and Environment Safety Management System, ILO
and EPA Standards. Industrial Hygiene: Definition of Industrial Hygiene,
Industrial Hygiene: Control Methods, Substitution, Changing the process,
Local Exhaust Ventilation, Isolation, Wet method, Personal hygiene,
housekeeping and maintenance, waste disposal, special control measures.
3 UNIT –III 9
Element of training cycle, Assessment of needs. Techniques of training,
design and development of training programs. Training methods and
strategies types of training. Evaluation and review of training programs.
Chemical Hazard: Introduction to chemical hazards, dangerous properties
of chemical, dust, gases, fumes, mist, Vapours, Smoke and aerosols.
Evaluation and control of basic hazards, concepts of dose response
relationship, bio-chemical action of toxic substances. Concept of threshold,
limit values.
4 UNIT –IV 9
Occupational Health Hazards, Promoting Safety, Safety and Health training,
Stress and Safety, Exposure Limit. Ergonomics-Introduction, Definition,
Objectives, Advantages. Ergonomics Hazards. Musculoskeletal Disorders
and Cumulative Trauma Disorders. Physiology of respiration, cardiac cycle,
muscle contraction, nerve conduction system etc. Assessment of Workload
based on Human physiological reactions. Permissible limits of load for
manual lifting and carrying. Criteria or fixation limits.
5 UNIT –V 8
Bureau of Indian standards on safety and health 14489 - 1998 and 15001 –
2000, OSHA, Process Safety Management (PSM) as per OSHA, PSM
principles, OHSAS – 18001, EPA Standards, Performance measurements to
determine effectiveness of PSM. Importance of Industrial safety, role of
safety department, Safety committee and Function.
Course Outcomes:
1. The student will be able to understand the basics of occupational health and related issues.
2. Understanding of the fundamental aspects of safety, industrial hygiene along with learning theory
to safety training methodology.
3. Considerate about hazardous materials, emergency management, ergonomics and human factors
4. Able to understand the adverse effects of hazards and develop control strategies for hazardous
conditions and work practices
DRAFT EC-123
5. Learn about Indian standards of health and safety and able to apply applicable standards, regulations
and codes.
11.Suggested Books:
1. Handbook of Occupational Health and Safety, NIC, Chicago, 1982.
2. Encyclopedia of Occupational Health and Safety, Vol. I and II. International Labour
Organisation, Geneva, 1985.
3. Accident Preventional Manual, NSC Chicago, 1982.
4. Henrich, H.W., Industrial Accident Prevention, McGraw Hill, 1980.
EN-355 GIS & REMOTE SENSING

1. Subject Code: EN-355 Course Title: GIS & Remote Sensing
3. Examination Duration (ETE) (Hrs.): Theory 3 Hrs
4. Relative Weightage: CWS 25 PRS 0 MTE 25 ETE 50 PRE 0
5. Credits: 3
6. Semester:V
8. Prerequisite: Nil
9. Course Objectives:
1) Introduce GIS and its significance in engineering and science.

2) To familiarize students with GIS data and its applications.
3) To familiarize students about the basics of remote sensing and its multi concepts.
4) To disseminate knowledge about sensors and different kind of resolution in the area of remote
sensing.
5) To familiarize students about the diverse applications of remote sensing.
10. Detail of Course:
DRAFT EC-124
no.
1 Unit-1: Geographic Information System 7
Introduction, Definition of GIS, Components of GIS, Input data for GIS,

Geographical concepts
2 Unit-2:GIS Data 9
GIS data types, Data representation, Data sources, Geo-referencing of GIS

data, GIS database, Database Management System, Data analysis
terminology, GIS software packages, GIS application
3 Unit-3:Remote Sensing 8
Introduction to Remote Sensing and Remote Sensing System, Multi concept

of remote sensing, Advantages and disadvantages of remote sensing,
Electromagnetic radiation, Polarisation, Thermal radiation
4 Unit-4:Remote Sensing Platforms 9
Important remote sensing satellites, Classifications of sensors and

platforms, Passive and Active sensors, Major remote sensing sensors,
Spatial resolution, Spectral resolution, Radiometric resolution, Temporal
resolution, Glopal Positioning System
5 Unit-5:Application of Remote Sensing 9
Digital Image Processing, Application of Remote Sensing in Land use and

Land cover mapping, Ground water mapping, Urban growth studies,
Wasteland mapping, Disaster management, Agriculture, Forestry
application
Course Outcomes:
1.The Student will learn about basics of GIS and its significance.
2.The Student will be able to understand the utility of GIS data as well as Data Management System.
3.The Student will learn the fundamentals of remote sensing.
4.The unit of Remote Sensing Platform will generate a clear cut understanding among students about
the satellites, their functioning and Global Positioning System. Geographical information system,
its components, DMS and its various applications in real life.
5. The Student will be able to attain thorough knowledge about the application of remote sensing in
different areas.
11.Suggested Books:
DRAFT EC-125
1. Fundamentals of Remote Sensing – George Joseph, University Press, Hyderabad, India.
2. Remote Sensing and Geographical Information System – AM Chandra & SK Ghosh Narosa
Publishing House, New Delhi.
3. Concepts and Techniques of Geographic Information Systems – C. P. Lo & Albert K.W.

Yeung, PHI Learning Private Limited, New Delhi.
4. Geographic Information System – Kang Tsung Chang, Tata Mc Graw hill, Publication
Edition, 2002.
EP351 PHYSICS OF ENGINEERING MATERIALS

1. Subject code: EP351 Course title: Physics of Engineering Materials
3. Examination Duration (Hrs): Theory: 3 Practical: 0
5. Credits: 3
6. Semester: ODD
7. Subject area: UEC
9. Objective: To familiarize the fundamentals /basic concepts and advances of
the different materials keeping in view of the engineering
applications. There is ample opportunity to become involved in
cutting edge Materials Science and Engineering Research
10.Detail of Course:

No. Hours
1. Crystallography:
Introduction to crystal physics,Space lattice, Basis and the Crystal structure, Bravais
lattices; Miller indices, simple crystal structures,Interplanar spacing, Intra and
Intermolecular bonds (Ionic, Covalent, Metallic, Van der Waals and Hydrogen Bond),
Defects in crystals, Basics of X- ray diffraction and its applications 10
DRAFT EC-126
2. Semiconductors:
Band theory of solids, Intrinsic and Extrinsic semiconductors, Statistics of electrons and
holes in intrinsic semiconductor, Hall effect, Effect of temperature on conductivity,
Generation and recombination, drift and diffusion current, Einstein relation, Applications 10
of Semiconducting Materials.
3. Dielectric and Magnetic Materials
Dielectric Materials: Dielectric polarization and dielectric constant, Various polarization

processes, Applications of Dielectric Materials
07
Magnetic Materials: Concept of Magnetism, Classification of dia-para, Ferro, Antiferro
and Ferrimagnetism, ferrites, soft and hard magnetic materials, Applications of Magnetic
Materials
4. Superconductivity:
Introduction and historical developments; General properties of super conductors, Meissner 07

effect and its contradiction to the Maxwell’s equation; Types of Superconductors, London
equations, Penetration depth, High Temperature Superconductors, Applications of
superconductors.
5. Advanced Engineering Materials:
Introduction, Synthesis, characterization and applications of Photonic glasses, Phosphors 08

and Nanophosphors, other selective topics in advanced materials.
Total 42
11.Suggested Books:
S. Name of Books/ Authors

No.
1. Introduction to Solid State Physics, by C. Kittel, 1996/ John Wiley & sons
2. Solid State Physics, by S. O. Pillai, 2010/ New Age International (P) Ltd.
3. Materials Science and Engineering by V. Raghavan, 2009/PHI Learning Pvt. Ltd.
4. Solid State Physics, N. W. Ashcroft and N. D. Mermin, 1976/ HBC Publication

5. Engineering Materials Science by Milton Ohring, 1995/Academic Press
6. Material Science and engineering: An Introduction By W. D. Callister Junior, 2007/ John
Wiley & Sons, Inc
7. Handbook of Electronic and Photonic Materials by SafaKasap, Peter Capper (Eds.),
2006/Springer
DRAFT EC-127
EP353 NUCLEAR SECURITY
1. Subject code: EP353 Course title: Nuclear Security
3. Examination Duration (Hrs): Theory: 3 Practical: 0
4. Relative Weight: CWS: 25, PRS:--, MTE: 25, ETE: 50, PRE: --
5. Credits: 4
6. Semester: EVEN/ODD
7. Subject area: UEC
8. Pre-requisite: Basic knowledge of Nuclear Physics
9. Objective: This course will provide basic understanding of Nuclear Security

which is essential for establishing nuclear culture in the society
10. Detail of Course:5th/6th Semester
S. Contents Contact
No. Hours
1. Introduction to nuclear security: Basics of nuclear security, Practice and culture, 08

Background, Objective, Scope, Structure, Nuclear security and safety culture:
Characteristics of nuclear security culture
2. Nuclear security regime, Importance of human factor and management leadership in 07

nuclear security, Nuclear security threats: Threat informed security, The design basis
threat
3. System characterization, PPS requirements and objectives: Facility characterization, 06

Target identification, Consequence analysis, PPS performance objectives
4. Physical protection system technologies: Intrusion detection, Exterior and Interior 09

Sensors, Access control, Contraband detection, Field detection sensors at
borders/major public Events, Alarm assessment, Communication and display, Access
delay, Response and neutralization, Response strategies and impact of On and Off site
response, Cyber security.
5. Security system design and evaluation: Adversary path analysis and Multi path 08
optimization, Scenario development, Insider analysis, Transportation, Design
approaches and vulnerability assessments, System design at major public events,
DRAFT EC-128
Design of security systems to interrupt illicit trafficking, Analysis of quantitative risk
assessment methods.
6. Consequence mitigation and event response: Consequence management following 04

nuclear events, Analysis of deterrence value of security measures, Roles and
responsibilities of institutions and individuals
Total 42
11.Suggested Books
S. Name of Books/ Authors

No.
1. Nuclear security briefing book, by Wyn Bowen, Matthew Cottee, Chris Hobbs, Luca Lentini
and Matthew Moran, 2014/King’s College, London, UK
2. IAEA Nuclear Security Series No. 13, Nuclear Security recommendations on physical
protection of nuclear material and nuclear facilities by IAEA, 2011/International Atomic
Energy Agency (IAEA)
3. The International Legal Framework of Nuclear Security: IAEA International law
series No. 4 by IAEA, 2011/International Atomic Energy Agency (IAEA)
4. Seeking Nuclear Security Through Greater International Cooperation by Jack Boureston and
Tanya Ogilvie-White, 2010/Council on Foreign Relations (CFR’s) International Institutions
5. Book Review: South Asia’s Nuclear Security by Bhumitra Chakma , 2015/Oxon, UK,
Routledge
HU351 ECONOMETRICS
1. Elective Paper - Econometrics

During Subject Open for Branches Per week- L- During
Code T-P semester
Odd semester 351 MC, CE, EN, BT, EP, PS 3-0-1 5 th
Even semester 352 EE, EL, CO, SE, AE, ME, 3-0-1 6 th
PE
(Note: i. History of this subject in DTU is different from other subjects. This subject was demanded by
the students in final year. It is supported by the placement data also that number of non-technical
companies visiting campus for recruitment is increasing over year.
2. Examination Duration: 3 Hrs.
3. Relative Weightage- will be decided at University level
4. Credits: 3 (Four)
DRAFT EC-129
5. Semester: Fifth and Sixth Semester
6. Subject Area: UEC Economics (Social Science)
7. Pre-requisite- Nil
Syllabus Hours ( Total - 56)

1 Introduction Hrs
1.1 What is Econometrics? Why a separate discipline? How it is different from 6
Mathematical Economics, Type of Data, Sources of data
1.2 Estimating Economic Relationship, Methodology of Econometrics
1.3 Matrix and its Economic Application
2 Review of Calculus 12
2.1 Differential Calculus and its application in Economics- Elasticity of demand- Price
and Cross; Profit maximization under Perfect Competition, Monopoly, Oligopoly and
Monopolistic Competition
2.2 Integral Calculus and its application in Economics - Capital Formation, Compound
Interest; Capital value and Flow Value; Consumer surplus under pure competition and
monopoly; Producers Surplus
2.3 Differential Equation and its application in Economics – Market Price Function;
Dynamic Multiplier;
3. Review of Statistics 14
3.1 Basic Ingredients of an Empirical study- Formulating a Model; Gathering data
Descriptive Statistics and its use in Business- Measure of Central Tendency: AM,
GM and HM, Median, Mode, Dispersion, Range, Quartile, standard Deviation,
Skewness, Kurtosis,
3.2 Probability - Discrete and Continuous; Probability Distribution: Binomial and
Poison distribution
3.3 Sampling techniques, Estimation and Hypothesis Testing, Interpreting the results
Mid semester
4. Regression 8 Hours
Statistical verses Deterministic Relationships, Regression verses Causation; Two variable

Regression Analysis; Population Regression Function (PRG), Stochastic specification of
PRF; The Significance of the Stochastic Term; stochastic disturbance Term; the sample
regression Function (SRF); Method of Ordinary Least Squares; Properties of Least Square
Estimators: The Gauss-Markov Theorem, Coefficient of determination r2 : A Measure of
“goodness of fit”; Monto Carlo Experiments
5. Classical Normal Linear Regression Mode (CNLRM) 4 Hours
DRAFT EC-130
The Probability distribution of Disturbances (meu); Normality Assumption, Method of
Maximum Likelihood
Multiple regression Analysis: The Problem of estimation; The problem of Inference
Cobb-Douglas Production function; Polynomial Regression Model; Testing for structural or

Parametric stability of regression Models; the Chow test
6. Dummy Variable (DV) 6 Hours
Nature; ANOVA models; Regression with a mixture of Quantitative and Qualitative

regressors: The ANCOVA Models; DV alternative to the Chow Test; Interaction effects
using Dummy Variable; Use of DV in seasonal Analysis
7. Presentation on Application of Mathematics, Statistics, 6 hrs.

Operational Research , Computer Science or any other related
subject to discuss any Aspect of Economics
11.Suggested books
S.No. Name of Books, Authors, Publishers

1. Wooldridge Jeffrey , Introductory Econometrics, Cencage Learning- ISBN-13-978-81-
315-1673-7; ISBN-1081-315-1673-3,2014
2. Damodar N. Gujrati, Basic Econometrics, Mcgraw Hill Education (India) Limited, Fifth
Edition,2013 ISBN-978-0-07-133345-0; ISBN; 0-07-133345-2
3.
Ramu Ramanathan, Introductory Econometrics with Applications, Harcourt Brace
Jovanovich Publishers, Latest USA ISBN-
MA351 HISTORY CULTURE & EXCITEMENT OF

MATHEMATICS
1. 1 Subject code: MA351 Course title: History Culture and Excitement of Mathematics
2. Contact Hours: L-3 T-0 P-0
3. Examination Duration (Hrs) Theory: 3hrs
4. Relative weightage: CWS: 25, PRS: -MTE: 25 ETE: 50 PRE: 0
5. Credits: 3
6. Semester Odd
8. Pre requisite --
9. Objective: To be capable in learning the history and culture on the Mathematics subjects
No. Hours
DRAFT EC-131
1. Ancient, Medieval and Modern Indian Mathematics: Aryabhata, 7
Brahmagupta, Bhaskar, Lilavati, Ramanujan
2 Introduction to Ancient books of Indian Mathematicians: Sidhantas, 7
Sulvasutras, Vedic Mathematics
3 Contribution of Indian Mathematicians in the field of Mathematics: 7
Value of Pi, The symbol zero, Number theory, Trigonometry, and
Mensuration, Hindu Multiplication, Long Division, Indeterminate
equation
4 Mathematicians Around the world: Newton, Leibnitz, Cauchy, 7
Lagrange in the field of Geometry, Calculus, Algebra, Probability
5 Algebra in the Renaissance: Solution of cubic equation, Ferrari’s 7
Solution in the quartic equation, Irreducible Cubics and complex
numbers
6 Paradoxes, Fallacies and Pitfalls of Mathematics 7
Total 42
11.Suggested books
S.No. Name of Books, Authors, Publishers

1. History of Mathematics, by carl B Boyer, Wiley International edition, 1968.
2. Mathematics of Music, Susan Kelly, UW-L Journal of under graduate research, Vol-
XIV, 2011.
ME 351 POWER PLANT ENGINEERING

1. Subject Code: ME 351 Course Title: Power Plant Engineering
2. Contact Hours: 42 L: 3 T: 0 P: 0
5. Credits: 3
6. Semester: V
9. Objective: To familiarize the students with thermodynamic cycles and various components of power
plants.
DRAFT EC-132
Hours
1 Indian energy scenario, Indian coals: formation, properties, analysis, benefication and 7
heating value calculation of coals; coking and non-coking coals, fuel handling systems; coal
gasification. Classification of power plants, base load and Peak load power stations, co-
generated power plant, captive power plant, and their fields of application & selection
criteria,.
2 Steam Generators: High pressure utility boiler, natural and forced circulation, coking and 7
non-coking coal, coal benefication, coal pulverization, pulverized fuel firing system,
combustion process, need of excess air, cyclone furnace, fluidized bed boiler, electrostatic
precipitators and wet scrubbers, boiler efficiency calculations, water treatment.
3 Combined Cycle Power Plants: Binary vapour cycles, coupled cycles, gas turbine- steam 7
turbine power plant, gas pipe line control, MHD- Steam power plant.
4 Other power plants: Nuclear power plants - working and types of nuclear reactors, boiling 7
water reactor, pressurized water reactor, fast breeder reactor, controls in nuclear power
plants, hydro power plant -classification and working of hydroelectric power plants, tidal
power plants, diesel and gas power plants.
5 Instrumentation and Controls in power plants: Important instruments used for 7
temperature, flow, pressure, water/steam conductivity measurement; flue gas analysis, drum
level control, combustion control, super heater and re-heater temperature control, furnace
safeguard and supervisory system (FSSS), auto turbine run-up system(ATRS).
6 Environment Pollution and Energy conservation: Economics of power generation: load 7
duration curves, power plant economics, pollution from power plants, disposal/management
of nuclear power plant waste, concept of energy conservation and energy auditing.
Total 42
Suggested Books:

1 Power Plant Engineering by M.M. Elwakil, Tata McGraw Hill, ISBN- 0070662746.
2 Power Plant Engineering by P.K Nag, Tata McGraw Hill, ISBN- 0070435993.
3 Steam and Gas turbines by A Kostyuk and V Frolov, MIR Publishers, ISBN- 9785030000329.
4. Modern Power Plant Engineering by J Wiesman and R Eckart, Prentice hall India Ltd, ISBN-
97801359725.
5. Planning Fundamentals of thermal Power Plants by F.S Aschner, John Wiley, ISBN- 07065159X.
6. Applied Thermodynamics by T.D Eastop and McConkey, Longman Scientific and Technical, ISBN-
0582305351.
7. CEGB volumes on power plant, Cwntral Electricity Generation Board, ISBN- 0080155680.
8. NTPC/NPTI publications on Power plants, ISBN- 9788132227205.
DRAFT EC-133
ME353 RENEWABLE SOURCES OF ENERGY
1. Subject Code: ME 353 Course Title: Renewable Sources of Energy
5. Credits: 3
6. Semester: V
9. Objective: To familiarize the students with renewable energy sources like solar, geothermal, wind and
tidal.

No. Hours
1 Man and Energy, world production and reserve of conventional energy sources, Indian 7
production and reserves, Energy alternatives
2 Solar radiation: Origin, nature and availability of solar radiation, estimation of solar 7
radiation. Photovoltaic cells. Design consideration and performance of different types of
solar cells. Flat plate, focusing collectors. Effects of receiving surface location and
orientation.
3 Devices for solar thermal collection and storage. Energy storage devices such as water 7
storage systems, packed Bed storage systems, phase change storage systems. Heat transfer
considerations relevant to solar energy. Characteristics of materials and surfaces used in
solar energy absorption.
4 Application systems for space heating, solar water pumps, solar thermal pond, Solar 7
Thermal Power plants, solar distillation, Solar Refrigeration and solar air conditioning, other
solar energy utilization.
5 Solar PV systems. Fuel Cell Technologies. 7
Generation and utilization of biogas, design of biogas plants, Wind energy systems.
6 Geothermal Energy Systems. Tidal energy systems. Oceanic power generation. Design 7
considerations, Installation and Performance Evaluation. MHD power generations. Role of
the nonconventional energy sources in power planning.
Total 42
11.Suggested Books:

1 G. D. Rai, “Energy Technolgy”, Khanna Publishers, ISBN- 97881740907438.
2 S.P. Sukhatme, “ Solar Energy”, Tata-Mcgraw hill, New Delhi, ISBN- 0074624531.
DRAFT EC-134
3 “Solar Energy thermal process” JADuffie and W.A. Beckman, John Wiley& sons, New York, ISBN-
1118418123.
4 Solar energy, Frank Kaieth& Yogi Goswami, Taylor and Francis, ISBN- 1560327146.
5 Treatise of Solar Energy, H.P. Garg, John Willey & sons, ISBN- 9027719306.
ME355 COMBUSTION GENERATED POLLUTION

1. Subject Code: ME 355 Course Title: Combustion Generated Pollution
5. Credits: 3
6. Semester: V
9. Objective: To introduce the students to different types of fuels, emissions from various engines, exhaust
treatment of various engines and instruments used for measuring emissions.

No. Hours
1 Engine fundamentals: Fuels, alternative fuels for IC engines, Type of hydro carbons. 7
Gasoline specifications. Effect of Engine parameters on performance, fuel injection for SI
engines, Engine vehicle road performance, road performance and fuel economy.
2 Emissions and air pollution: Automotive Emissions and their role in air pollution. Photo- 7
chemical smog. Chemistry of smog formation. Combustion in Homogeneous mixtures,
emission formation. Incomplete combustion, formation of hydro-carbons, Carbon
monoxide and oxides of nitrogen, Aldehyde emissions.
3 Influence of design and operating variables on gasoline engine exhaust emissions. 7
Hydrocarbon Evaporative Emissions: Various sources and methods of their control.

Canisters for controlling evaporative emissions. Emission control systems for gasoline
engines: Blow by control closed PCV system design.
4 Exhaust treatment devices: Air injection into exhaust system. 7
5 Thermal reactors, Catalytic convertor. 7
Stratified charge engines. Honda CVCC engine.
Diesel engine combustion Emissions: Sources of emissions during combustion. Effect of air
fuel ratio, speed, injection timing on performance and emission formation. D.I and I.D.I
engine emissions.
6 Methods of reducing emissions, exhaust gas recirculation, smoke emission from diesel 7
DRAFT EC-135
engines.
Emission Instruments: Non- dispersive Infrared analyzer, Gas chromatograph, flame

ionization detector, chemiluminescent analyzer
Total 42
11.Suggested Books:

1 Combustion generated air pollution, Earnest S Starkman, Springer, ISBN- 9780306305302.
2 Fundamentals of Air pollution engineering, Richard C. Hagan, Prentice Hall, ISBN- 0133325371.
3 Air pollution threat & response, David Alym, Addison-Wesley Publication, ISBN- 0201043556.
ME357 THERMAL SYSTEM

1. Subject Code: ME 357 Course Title: Thermal System
5. Credits: 3
6. Semester: V
9. Objective: To familiarise the students with the process of thermodynamic analysis of engineering systems
and to enhance critical thinking and provide them with a wider view to handle engineering problems.
Hours
1 Fundamentals: properties of pure substance in Solid, Liquid and Vapour Phases, PVT 7
Behavior of simple compressible system, T-S and H-S diagram, Steam Tables,
determination of quality of steam, Throttling Calorimeter, Combined Separating &
Throttling Calorimeter, Maxwell and other thermodynamics relations, mixture of non
reactive ideal gases, Real gases, Compressibility chart, Law of corresponding state, Air
water vapor mixture, calculation of properties of air water vapour mixture.
2 Rankine Cycle And Analysis: Rankine cycle and its representation on T-S and H-S 7
diagrams; Effect of low backpressure and high entry pressure and temperature and its
limitations; necessity of re-heating, ideal and actual regenerative feed water heating cycle
and its limitations. Typical feed water heating arrangements for various capacity power
plants.
3 Introduction To Boilers: Classification of Boilers, Boiler mountings and accessories; 7
draft systems, circulation system; Combustion and its calculations, and Boiler
DRAFT EC-136
performance.
4 Steam Nozzles: Types of Nozzles, Flow of steam through nozzles; Condition for 7
maximum discharge through nozzle; Nozzle efficiency. Effect of friction and
Supersaturated flow through nozzle.
5 Steam Turbines : Working principle and types of steam turbines; Velocity diagrams for 7
impulse and reaction turbines, compounding of impulse turbines; Optimum velocity ratio
and maximum efficiency. Comparison of impulse and reaction turbines. Condition line
and reheat-factor, losses in steam turbines; governing of steam turbines.
6 Condensers and Cooling towers: Types and working of condensers, types and 7
performance of cooling towers.
Total 42
11.Suggested Books:

1 Engineering Thermodynamics by P.K.Nag, Tata McGraw Hill Publishing Company Limited, ISBN –
1259062562, 2013.
2 Engineering ThermodynamicsbyRogers, Pearson Education, ISBN- 631197036.
3 Thermodynamics by Kenneth Wark, Mcgraw-hill Book Company, 5th edition, ISBN- 0070682860, 1988.
4. Engineering Thermodynamics: work and heat transfer by Gordon Rogers and Yon Mayhew, Longman,
4th edition, ISBN – 0471861731, 1992.
5. Fundamentals of Classical Thermodynamics by Van Wylen and Sonntag, John Wiley & Sons Inc., 3rd
edition, ISBN – 0471861731, 1986.
6. Fundamentals of Engineering Thermodynamics by Moran and Shaprio, John Wiley & Sons, Inc., 7th
edition, ISBN – 0470917687, 2010.
7. Thermodynamics: An Engineering Approach by Cengel and Boles, The McGraw-Hill Companies, 8th
edition, ISBN: 0073398179, 2014.
8. Applied Thermodynamics for Engineering TechnologistsbyT.D. Eastop, Prentice Hall, 5th edition, ISBN-
05820919344, 1993.
9. Treatise on Heat Engineering by V. P.Vasandani and D.S. Kumar, Metropolitan Book Co. (p) Ltd., ISBN-
810003500.
ME359 REFRIGERATION & AIR

CONDITIONING
1. Subject Code: ME 359 Course Title: Refrigeration and Air Conditioning
5. Credits: 3
6. Semester: V
DRAFT EC-137
9. Objective: To learn properties of different refrigerants, and thermodynamic cycles of refrigeration.To
understand comfort parameters and air conditioning.

No. Hours
1 Introduction to Refrigeration: 7
Necessity and applications, unit of refrigeration and C.O.P., types of Ideal cycles of
refrigeration, air-refrigeration, bell coleman cycle, open and dense air systems, actual air-
refrigeration system problems, refrigeration needs of aircrafts, actual refrigeration system
2 Vapour Compression Refrigeration: 10
Working principle and essential components of the plant, simple vapour compression
refrigeration cycle - COP, Representation of cycle on T-S and p-h charts - effects of sub
cooling and super heating - cycle analysis - Actual cycle, Influence of various parameters
on system performance – necessity of multistaging, multistage compression system, and
their analysis, necessity and working of cascading system
3 Refrigerants and Absorption Refrigeration: 4
Desirable properties of refrigerants, classification of refrigerants used, nomenclature, ozone
depletion, global warming, vapor absorption system, calculation of max COP.
4 Air Conditioning: 7
Psychometric properties & processes, comfort air-conditioning, summer and winter air-
conditioning, cooling & dehumidification systems, load calculation and applied
psychrometry.
5 Human Comfort: 7
Requirements of human comfort and concept of effective temperature, comfort chart,
comfort air-conditioning, requirements of industrial air-conditioning, air-conditioning load
calculations.
6 Control: 7
Refrigeration and air-conditioning control, air handling, air distribution and duct design
Total 42
11.Suggested Books:

1 Refrigeration and Air Conditioning by C. P. Arora, Tata McGraw Hill, ISBN- 9788120339156.
2 Refrigeration and Air Conditioning by A. R .Trott and T. C. Welch, Butterworth- Heinemann, ISBN-
9780080540436.
3 Refrigeration and Air ConditioningTechnology by Whitman, Jhonson and Tomczyk, Thomson Delmer
Learning, ISBN- 1111644470.
4 Refrigeration and Air Conditioning by Abdul Ameen, Prentice Hall of India Ltd, ISBN- 9789303206560..
5 Basic Refrigeration and Air Conditioning by P. N. Ananthanarayan, Tata McGraw Hill, ISBN-
9789383286560.
6 Refrigeration and Air Conditioning by Wilbert F. Stoecker and Jerold W. Jones, Tata McGraw Hill, ISBN-
007061623X.
DRAFT EC-138
7 Refrigeration and Air Conditioning by Richard Charles Jordan, Gayle B. Priester, Prentice hall of India Ltd,
ISBN-9780406269313.
8 ASHRAE Handbook – Refrigeration 2010, ISBN- 9781933742922.
ME361 INDUSTRIAL ENGINEERING

1. Subject Code: ME361 Course Title: Industrial Engineering
5. Credits: 4
6. Semester: V
9. Objective: To make students aware of industrial engineering concepts of work study and measurement,
quality control and reliability etc.

No. Hours
1 Introduction 7
Introduction, Definition and objectives of Industrial Engineering, Scope of Industrial
Engineering, Production systems and their classifications; Productivity-Total and partial
productivity, Reasons and remedy for poor productivity
2 Job analysis and Work Measurement Systems 7
Work System Design: Taylor’s scientific management, Gilbreth’s contributions; method
study, micro-motion study, principles of motion economy; work measurement - stop watch
time study, micro motion and memo motion, work sampling, standard data, PMTS;
ergonomics; job evaluation, merit rating, incentive schemes, and wage administration;
business process reengineering
3 Production Planning and Control 7
Types and characteristics of production systems Objective and functions of Production,
Planning & Control, Routing, Scheduling and Operations scheduling, production
scheduling, job shop scheduling problems, sequencing problems, scheduling tools and
techniques, Loading, Dispatching and its sheets & Gantt charts
4 Quality Engineering 7
Quality concept and costs; statistical quality control, Concept of specification limits,
statistical control limits, process capability, Process control and control charts for both
attributes and variable data. Acceptance Sampling- Single and double sampling
DRAFT EC-139
5 Reliability and Maintenance 7
Reliability, availability and maintainability; distribution of failure and repair times;
determination of MTBF and MTTR, reliability models; system reliability determination;
Maintenance management and its objectives, Various types of Maintenance Planning,
House Keeping, 5S concepts
6 Material Handling 7
Principles, functions, and objectives of Material Handling; Selection and classification of
Material Handling Equipments; Relation of material handling with plant layout
Total 42
11.Suggested Books

1 Industrial Engineering and Management; B. Kumar, Khanna Publication, ISBN- 8174091963, 2011.
2 Introduction to work Study, International Labour Office, Geneva, 3rd edition, Oxford and IBH publishing Co.
Pvt. Ltd, New Delhi, ISBN- 8120406028, 2008.
3 Industrial Engineering and Management, Pravin Kumar, Pearson Education, 1st edition, ISBN-
9789332543560, 2015.
ME363 PRODUCT DESIGN &

SIMULATION
1. Subject Code: ME363 Course Title: Product Design & Simulation
5. Credits: 3
6. Semester: V
9. Objective: To familiarize the students with the process of product design and development.
No. Hours
1 Stages in design process: 5

Introduction to various stages of the design process: Formulation of problem, Generate
alternatives, Evaluation, Guided Redesign. Case study.
2 Product life cycle: 5
New product introduction: early introduction, increased product life. Life cycle
management tool, System integration, QFD, House of quality, Pugh’s method, Pahl and
DRAFT EC-140
Beitz method. Case studies
3 Value engineering: Introduction, nature and measurement of value. Value analysis job 5
plan. Creativity. Value analysis test. Case studies
4 Concurrent/ reverse engineering: 5
Introduction, basic principles, components, benefits of concurrent engineering. Concept of
reengineering
5 Material selection: Materials in design. The evolution of engineering materials. Design 5
tools and material data. Material selection strategy, attribute limits, selection process,
material selection. Case studies
6 Process selection: Introduction. Process classification: shaping, joining and finishing. 5
Systematic process selection, process cost. Computer – aided process selection
7 Design for manufacture and assembly: Design for Manufacture and Assembly (DFMA). 4
Reasons for not implementing DFMA. Advantages of DFMA with case studies. Design
features and requirements with regard to assembly, Design for Manufacture in relation to
any two manufacturing processes: machining and injection molding. Need, objectives
8 System Simulation: Techniques of simulation, Monte Carlo method, Experimental nature 4
of simulation, Numerical computation techniques, Continuous system models, Analog and
Hybrid simulation, Feedback systems, Computers in simulation studies, Simulation
software packages
9 Simulation of Mechanical Systems: Building of Simulation models, Simulation of 4
translational and rotational mechanical systems, Simulation of hydraulic systems
Total 42
11.Suggested Books:

TEXT BOOKS:
1 David G Ullman, “The Mechanical Design Process.” Publisher- McGrawhillIncSingapore, ISBN-13:
9780072975741, 1992.
2 Kevin Otto & Kristin Wood Product Design: “Techniques in Reverse Engineering and new Product
Development.” 1 / e 2004 , Publisher- Pearson Education New Delhi , ISBN-13: 9780130212719,
3 L D Miles “Value Engineering.”Publisher- McGraw-Hill, 1972
4 Karl T Ulrich, Steven D Eppinger , “ Product Design &Development.”Publisher- Tata McGrawhill New
Delhi, ISBN-13: 9780078029066, 2003
5 Hollins B & Pugh S “Successful Product Design.” Publisher- Butter worths London, ISBN 9780408038614.
6 N J M Roozenberg , J Ekels , N F M Roozenberg “ Product Design Fundamentals and Methods .”Publisher-

John Willey & Sons, ISBN-13: 9780471954651, 1995.
ME365 COMPUTATIONAL FLUID

DYNAMICS
1. Subject Code: ME 365 Course Title: Computational Fluid Dynamics (CFD)
DRAFT EC-141
5. Credits: 3
6. Semester: V
9. Objective: To provide basic concepts of CFD in terms of comprehensive theoretical study and its
computational aspects.
No. Hours
1 Introduction to CFD, Historical background, Impact of CFD 3

2 The Governing Equations of Fluid Dynamics 7
Derivation, Discussion of physical meanings and Presentation of forms particularly
suitable to CFD.
3 Mathematical Behavior of Partial Differential Equations: 6
Impact on CFD
4 Basic Aspects of Discretization: 12
Introduction to Finite Difference, Finite Elements and Finite Volume Methods.
Detailed treatment of Finite Difference method, explicit and implicit methods, errors and
stability analysis.
5 Grids with Appropriate Transformations Adaptive grids and unstructured meshes. 7
Lift reduction, down force generation and drag reduction. An introduction to the
aerodynamics of airflows for cooling.
6 Commercial codes (e.g. FLUENT etc.). Grid generation, techniques and application. 7
Basic principles and concepts and the characteristics of wings and diffusers
Total 42
11.Suggested Books:

1 Computational Fluid Dynamics”,John Anderson,” McGraw- Hill Ltd.
2 Computational Fluid Dynamics”,Tu, Elsevier.
3 Introduction to Computational Fluid Dynamics,Niyogi, Pearson Education, Delhi
ME367 FINITE ELEMENT METHODS

1. Subject Code: ME 367 Course Title: Finite Element Methods
DRAFT EC-142
5. Credits: 3
6. Semester: V
9. Objective: To enable students to apply Galerkin method and virtual work principle to problems in solid
mechanics. To teach them numerical solution of differential equations with finite element method.
No.
1 Fundamental concepts of the Finite Element Method. One Dimensional 12

Problem(Bar of uniform and variable cross sections), The Galerkin Approach,
The potential –Energy Approach, shape Functions, Derivation of stiffness matrix
and load vector for the element and for the entire domain. Evaluation of
displacement, stresses and reaction forces.
2 Trusses:-. Introduction, Plane Trusses, Local and Global coordinate Systems, 3
Element Stiffness Matrix and Stress calculations
3 Two –Dimensional problem using Constant strain triangles(CST), Two- 6
dimensional isoparametric elements and numerical integration ,element stiffness
matrix, Force vector.
4 Applications of finite element method to heat transfer. 4
5 Application of finite element method to electrical systems. 10
6 Dynamic analysis:- Element mass matrices,Evaluation of Eigenvalues and 7
Eigenvectors.
Use of Softwares such as MAT LAB/ABAQUS/ANSYS/ NASTRAN/IDEAS.
Basic feature of these softwares.
Total 42
11.Suggested Books:

1 Finite Element Procedures, K.J. Bathe, Prentice Hall of India.
2 Finite Elements in Engineering by Chandrupatla and Belegundu.
3 Finite element Method by J.N.Reddy.
4. Finite element Method,O.C. Zienkiewicz& R.A. Taylor
5. Finite element Analysis,C.S. Krishnamurthy
6. Finite element Method, Kenneth H. Hubener
DRAFT EC-143
7. Finite Element Method, Desai & Abel
ME369 TOTAL LIFECYCLE

MANAGEMENT
1. Subject Code: ME 369 Course Title: Total Lifecycle Management
5. Credits: 3
6. Semester: V
9. Objective: To familiarize the students with the concept of Total Life Cycle, and applying life cycle
thinking to define tradeoffs. This course also introduces to sustainability and use of renewable resources.

No. Hours
1 Introduction: Extensive definition of Concurrent Engineering (CE), CE design 8

methodologies, Review of CE techniques like DFM (Design for manufacture), DFA
(Design for assembly), QFD (Quality function deployment), RP (Rapid prototyping), TD
(Total design), for integrating these technologies, Organizing for CE, CE tool box,
Collaborative product development
2 Use of Information Technology: IT support, Solid modeling, Product data management, 8
Collaborative product
Commerce, Artificial Intelligence, expert systems, Software hardware component design.
3 Design Stage: Lifecycle design of products, Opportunities for manufacturing enterprises, 8
Modality of concurrent engineering design, automated analysis, Idealization control, CE
in optimal structural design, Real time constraints
4 Need for PLM: Importance of PLM, Implementing PLM, Responsibility for PLM, 9
Benefits to different managers ,Components of PLM, Emergence of PLM, Lifecycle
problems to resolve, Opportunities to seize
5 Components of PLM: Components of PLM, Product lifecycle activities, Product 9
organizational structure, Human resources in product lifecycle, Methods, techniques,
Practices, Methodologies, Processes, System components in lifecycle, slicing and dicing
the systems, Interfaces, Information, Standards
Total 42
DRAFT EC-144
11.Suggested Books:

1 Integrated Product Development M.M. Anderson and L Hein IFS Publications
2 Design for Concurrent Engineering J. Cleetus CE Research Centre, Morgantown
3 Concurrent Engineering Fundamentals: Integrated Product Development Prasad Prentice hall India
4 Concurrent Engineering in Product Design and Development I Moustapha New Age International
5 Product Lifecycle Management John Stark Springer-Verlag, UK
6 Product Lifecycle Management Michael Grieves McGraw Hill
7 Concurrent Engineering: Automation tools and Technology Andrew Kusiak Wiley Eastern
ME371 VALUE ENGINEERING

1. Subject Code: ME 371 Course Title: Value Engineering
5. Credits: 3
6. Semester: V
9. Objective: To understand the concept and approaches of value analysis and engineering with an emphasis
on case studies.
No. Hours
1 An Overview Of Value Engineering-Concepts and approaches of value analysis and 8

engineering - importance of value, Function - identity, clarify – analysis
2 Evaluation of VE-Evaluation of function, Problem setting system, problem solving 8
system, setting and solving management - decision - type and services problem,
evaluation of value
3 Results accelerators, Basic steps in using the systems 8
4 Understanding the decision environment, Effect of value analysis on other work in the 9
DRAFT EC-145
business- Life Cycle Cost (LCC), Case studies
5 VE Level Of Effort-VE Team, coordinator, designer, different services, definitions, 9
construction management contracts, value engineering case studies, Effective
organization for value work, function analysis system techniques- FAST diagram, Case
studies
Total 42
11.Suggested Books:

1 Parker, D.E., “Value Engineering Theory”, Sundaram publishers, 1990
2 Miles, L.D., “Techniques of Value Engineering and Analysis”, McGraw Hill Book Co., 2nd End., 1972
3 Khanna, O.P., “Industrial Engineering and Management”, Dhanpat Rai and Sons, 1999.
MG351 FUNDAMENTALS OF FINANCIAL ACCOUNTING AND

ANALYSIS
1. Subject Code : MG351 Course Title: Fundamentals of Financial Accounting

and Analysis
2. Content Hours L: 3 T: 0 P: 0
4. Relative Weightage: CWS: 25 PRS MTE: 25 ETE : 50 PR
5. Credits: 3
6. Semester: V (ME+AE+PE+CE+ENE+BT+MC+AP+PT)/ VI (COE+IT+SE+EC+ EE+EEE)
7. Subject Area: UEC Management
9. Objective: Familiarizing the students with the financial environment of business, especially the
financial markets and acquaint them with accounting mechanics, process and system.
Unit Detail Contents No. Of

No. Hrs.
1 Introduction to Management :Basic concepts of management, 8
management process, principles of management, functions, levels,
managerial roles and skills, managerial ethics and corporate social
responsibility
2 Introduction to Financial Environment and accounting: Financial 10

Markets - Capital Markets, Basics of capital market mechanism, instruments,
DRAFT EC-146
financing and rating institutions. Importance, Objectives and Principles of
Accounting, Accounting Concepts and conventions, and the Generally
Accepted Accounting Principles (GAAP) Overview of the Accounting
Process. Accounting standards as Issued by Institute of Chartered
Accountants of India (ICAI).
3 Overview of Business Activities and Principal Financial Statements: 8

Observe the types of information provided by the three principal financial
statements and how firms might use this information in managing and
evaluating a business. Understand the rationale and the information value of
the statements of Balance Sheet, Profit and Loss statement, cash flows.
4 Financial Analysis-I: Distinction between cash profits and book profits. 8

Understanding the cash flow statement and the funds flow statement.
5 Financial Analysis –II: Importance, objectives and concept of Ratio 8

Analysis- Liquidity, leverage, solvency and profitability ratios.
Total 42
11.Suggested Books
S. No. Name of Books / Authors/ Publishers

1 Fundamental of Management, Stephen P. Robbins, David A. De Cenzo and Mary
Coulter, Pearson Education,2011, ISBN- 978-0273755869
2 Introduction to Accountancy, 10 ed., T.S. Grewal, S. Chand and Company (P) Ltd., New
Delhi,2009, ISBN- 9788121905695
3 Advance Accounts by M.C Shukla and T.S Grewal and SC Gupta, S. Chand and
Company (P) Ltd., New Delhi,1997, ISBN- 9788121902786
4 Financial Accounting, 4 ed, S.N. Maheshwari and S.K. Maheshwari, Vikas
Pulication,2005, ISBN- 8125918523
5 Financial Accounting Reporting & Analysis, Cengage, 7/e, W Albrecht Stice & James
Stice, Cengage Learning,2010, ISBN- 0538746955
MG353 FUNDAMENTALS OF MARKETING
1. Subject Code :MG353 Course Title : Fundamentals of Marketing

3. Examination Duration (ETE )(Hrs.): Theory: 3 Hrs Practical 0
4. Relative Weightage: CWS:25 PRS MTE:25ETE:50PR
DRAFT EC-147
5. Credits: 3
6. Semester: Third (ME+AE+PE+CE+ENE+BT+MC+AP+PT)/ Fourth (COE+IT+SE+EC+

EE+EEE)
9. Objective: The basic objective of this paper is to make students aware of fundamental concepts
of marketing necessary for making decisions in complex business situations by managers and
start up entrepreneurs.
Unit No. Detail Contents No. Of

Hrs.
1 Basic concepts of management: management process, principles of 8
management, functions, levels, managerial roles and skills, managerial
ethics and corporate social responsibility
2 Introduction to marketing: nature and scope of marketing, 9

marketing mix, marketing vs. sales, role of marketing in society,
interface of marketing with other departments in organization,
Customer Life Time Value, ethical issues in marketing Concept of
market segmentation: consumer and industrial, targeting and
positioning, sales forecasting
3 Product mix decisions: new product development process, test 8

marketing, concept of Product Life Cycle, product packaging
decisions
4 Pricing decisions : consideration in setting price, major pricing 9

strategies, promotional mix decisions: advertising, sales promotion,
personal selling, publicity, opportunities and avenues of online
promotion
5 9
Promotion and distribution decisions :design and management of

distribution channel for physical products and services, reasons of
channel conflict, handling strategies, basic challenges in supply chain
management of e-commerce firms
Total 42
11. Suggested Books
DRAFT EC-148
Unit Name of Books / Authors/ Publishers
No.
1 Fundamental of Management, Stephen P. Robbins, David A. De Cenzo and Mary
Coulter, Pearson Education, 2011, ISBN-978-0273755869
2 Marketing Management, 14th ed., Philip Kotler , Kevin Lane Keller, Abraham Koshy
and MithileswarJha, Pearson Education, New Delhi, 2013,(ISBN-10: 9788131767160)
3 Marketing, 14th ed., Etzel, Bruce J Walker, William J Stanton and Ajay Pandit, Mc
Graw Hill Education, 2009, ISBN -9780070151567
4. MKTG, Charles W Lamb, Joe F Hair, Carl NcDaniel and Dheeraj Sharma, Cengage
Learning,2012, ISBN- 9788131517086
5. Marketing Management, RajanSaxena, Tata Mc Graw Hill Education, 2005, ISBN-

9780070599536
MG355 HUMAN RESOURCE MANAGEMENT
1. Subject Code : MG355 Course Title : Human

Resource Management
4. Relative Weightage: CWS:25 PRS MTE:25 ETE:50 PR
5. Credits: 3

EE+EEE)
9. Objective: To develop necessary understanding in design and execution of human resource strategies
for the achievement of organization goals.
Unit Content Contact

No. hours
1. Basic concepts of management: management process, principles of management, 8
functions, levels, managerial roles and skills, managerial ethics and corporate social
responsibility
DRAFT EC-149
2. Introduction: Concept, nature, scope, objectives and importance of HRM; Evolution 9
of HRM; Environment of HRM; Personnel Management vs HRM. Acquisition of
Human Resources: HR Planning; Job analysis – job description and job specification;
recruitment – sources and process; selection process – tests and interviews; placement
and induction. Job changes – transfers, promotions/demotions, separations.
3. Training and Development: Concept and importance of training; types of training; 8

methods of training; design of training programme; evaluation of training
effectiveness; executive development – process and techniques; career planning and
development.
4. Performance Appraisal: Performance appraisal – concept and objectives; 8

traditional and modern methods, limitations of performance appraisal methods.
5. Compensation and Maintenance: Compensation: job evaluation – concept, 9

process and significance; components of employee remuneration – base and
supplementary; maintenance: overview of employee welfare, health and safety,
social security.
Total 42
11.Suggested Books
S. No Name of the book /Authors /Publishers
1 Fundamental of Management, Stephen P. Robbins, David A. De Cenzo and Mary Coulter,

Pearson Education, 2011, ISBN-978-0273755869
2 Human Resource Management, G. Dessler, B. Varkkey, Pearson prentice Hall, 2011,

(ISBN – 978-81-317-5426-9)
3 International HRM a cross cultural approach, T. Jackson, Sage publications, London, 2002,
(ISBN – 0-7619-7404-0)
4 HRM and Performance: Achievements and Challenges, D. E. Guest, J .Paauwe, P. Wright,

John Wiley and sons, UK, 2013, (ISBN – 978-1-118-48261-2)
5 A Handbook of Human Resource Management Practice, M. Armstrong, Kogan Page Limited,

UK, 2007 ,(ISBN – 978–0–7494–4631-4)
.
MG357 KNOWLEDGE AND TECHNOLOGY MANAGEMENT
DRAFT EC-150
1. Subject Code :MG 357 Course Title : Knowledge and Technology Management
4. Relative Weightage: CWS:25 PRS MTE:25 ETE:50 PR
5. Credits: 3

EE+EEE)
9. Objective: Preparing the students to understand how the new age organizations are leveraging on the
power of knowledge and technology. Acquiring the knowledge to address the issues faced by the
corporate world for a deeper understanding.
Unit No. Contents Contact Hours

1. Basic concepts of management, management process, principles of 8
management, functions, levels, managerial roles and skills,
managerial ethics and corporate social responsibility
2. Introduction to Knowledge Management: Data, Information, 9

Knowledge Management (KM), Knowledge Society, Knowledge
Economy, Types of Knowledge, Tacit knowledge and explicit
knowledge, Essential components of KM model Building Knowledge
Assets: Various knowledge assets, Tools of Knowledge, Knowledge
Audit, AAR (After Action Review), Analyzing current knowledge
state.
3. Creating Strategies for Success: KM strategy, Codification, 9

Personalization, Knowledge Management Implementation,
Generating a KM-specific vision, Integrating organizational and
business goals with KM, Choosing the right KM techniques, Relevant
case studies in this area.
4. Understanding Technology: Definition, Key concepts, Need for 8

technology, History of technological developments, Role and
importance of technology in 21st century, Recent developments in the
field of technology.
5. Technology-Management integration: Management as a concept, 8

Technology management, Life cycle approach to technology
management, Innovation, Creativity, Technology innovation process.
DRAFT EC-151
Total 42
11.Suggested Books
S. No. Name of Books /Authors/Publishers
1. Fundamental of Management, Stephen P. Robbins, David A. De Cenzo and Mary Coulter,

Pearson Education,2011, ISBN-978-0273755869
2 Knowledge Management in Organizations: A Critical Introduction, Donald Hislop, Oxford

University Press,2013, ISBN: 9780199691937.
3 The Knowledge-Creating Company: How Japanese Companies Create the Dynamics of
Innovation, IkujiroNonaka and Hirotaka Takeuchi, Oxford University Press,1995, ISBN:
0195092694.
4 Hitotsubashi on Knowledge Management (Hardcover), Hirotaka Takeuchi and

IkujiroNonaka, John Wiley and Sons, 2004, ISBN: 0470820748.
5 Management of Technology: The Key to Competitiveness and Wealth Creation, Tarek Khalil
and Ravi Shankar, McGraw Hill Education (India) Private Limited, 2nd Edition, 2012, ISBN:
9780070677371.
PE351 ADVANCED MACHINING PROCESS
1. Subject Code: PE-351 Course Title: Advanced Machining Process
5. Credits: 3
6. Semester: V
DRAFT EC-152
9. Objective: To understand basic principles of various processes and their applications. State various
parameters influencing the machining process.

No. Hours
1 Introduction, need of advanced machining processes, hybrid processes, microelectro 7

mechanical system, (MEMS), nano electromechanical systems(NEMS),Ultrasonic micro
machining - mechanics of cutting, parametric analysis, process capabilities, applications.
2 Abrasive jet machining: Introduction, set ups, gas propulsion system, abrasivefeeder, 8
machining chamber, AJM nozzle, abrasive parametric analysis, processcapabilities,
applications, abrasive micro machining,
Water jet machining:Introduction, process characteristics, process performance, applications,

Abrasive Water jet machining: Abrasive finishing process: Working principle, parametric
analysis, process variables, process performance and applications,
3 Abrasive flow machining- Working principle, parametric analysis, process variables, process 10
performance and applications, Magnetorheological abrasive flow finishing- Working
principle, parametric analysis,process variables, process performance and applications,
Magnetic float polishing,Magnetic abrasive finishing- Working principle, parametric analysis,
processvariables, process performance and applications
4 Electro discharge machining (EDM): Introduction, Working principle, parametricanalysis, 7

process variables, process characteristics, applications, hybrid processessuch as electro
discharge grinding, diamond grinding, wire EDM, Electrodischargemicro grinding,
5 Laser beam machining- production of laser, working principle, types of laser, 8

processcharacteristics and applications. Electron beam machining: Working principle,process
parameter, process characteristics, and applications. Ion beam machining:Working principle,
process parameter, process characteristics, and applications.
6 Plasma arc machining: Working principle, Plasma arc cutting system, applications. 2
Total 42
S. No. Title, Author, Publisher and ISBN No.
DRAFT EC-153
1 Advanced machining process, Dr.V.K.Jain, Allied publisher, ISBN:978-81-7319-915-8.
2 Non traditional methods of manufacturing, Shan&Pandey, ISBN, 0070965536
PE353 SUPPLY CHAIN MANAGEMENT
1. Subject Code: PE-353 Course Title: Supply Chain Management
5. Credits: 3
6. Semester: V
9. Objective: To understand the key considerations at the various stages involved in the supply of product
in order to maintain the smooth flow from source to the point of consumption so that overall
organizational performance may improve.

No. Hours
1 Introduction:Perspective of Supply Chain Management, Managing uncertainty, Key issue in 6

supply chain management.
2 Inventory Management and Risk Pooling: Inventory management, Classification of 8

inventory, Centralized versus Decentralized Warehousing and Risk pooling, Value of
Information, Quantification of Bullwhip effect, Causes and remedies of Bullwhip effect.
DRAFT EC-154
3 Resource planning: Aggregate Production Planning- Chase and leveling strategies, MRP, 6
MRP-II, Agile manufacturing Systems
4 Procurement and Outsourcing strategies:Introduction, outsourcing benefits and risks, 7

Make/Buy decision, e-procurement, Vendor selection and quota allocation.
5 Strategic Alliances: Introduction, Third party logistics, Demand driven strategies, Distribution 8
strategies- direct shipment, cross docking, transshipment, Supplier relationships management,
Customer relationship management.
6 International Issues in Supply Chain Management: Concepts in Globalization, 7

Globalization forces, Risks and Advantages of International supply chains, Issues in
International supply chain management, Regional differences in logistics.
Total 42
1. Simchi-Levi, Kaminsky, Philip K. and ‘Designing and Managing the Supply Chain: Concepts, Strategic
and Case Studies’, McGraw-Hill/Irwin, (ISBN, 10: 0072357568, 13: 978-0072357561).
2 Supply Chain Management by Chopra and Mendle, ISBN: 9780132743952
3 Supply Chain Management: Text and Cases by JannatSah.,ISBN-10: 8131715175.
PE355 WORK STUDY DESIGN
1. Subject Code: PE-355 Course Title:Work Study Design
DRAFT EC-155
5. Credits: 3
6. Semester: V
9. Objective: To provide basic understanding to the students about the concept and significance of work
study and ergonomics. To impart thorough knowledge to the students about various techniques of work-
study for improving the productivity of an organization.

No. Hrs
1 Productivity: Definition, reasons for low productivity, methods to improve productivity, Work-study 4
and productivity
2 Human factor in work-study: Relationship of work-study man with management, supervisor & 5
workers, qualities of a work-study man.
3 Method-study: Definition, objectives, step-by-step procedure, questioning techniques, charts and 9

diagrams for recording data. Like outline process charts, flow process charts, multiple activity charts,
two handed process chart, string diagram, travel chart, cycle graph, Chrono-cycle graph, therbligs,
micro motion study and film analysis, Simo chart, principles of motion economy. Development and
installation of new method..
4 Work-Measurement: Definition, various techniques of work-measurement work-sampling, 9

stopwatch time study & its procedure, Job selection, Equipment and forms used for time study, rating,
methods of rating, allowances and their types, standard time, numerical problems, predetermined -
time standards and standard data techniques. Incentive: Meaning, objectives of an incentive plan,
various types of incentive plans
5 Ergonomics: Introduction, history of development, man-machine system and its components. 8

Introduction to structure of the body- features of the human body, stress and strain, metabolism,
measure of physiological functions- workload and energy consumption, biomechanics, types of
movements of body members, strength and endurance, speed of movements. NIOSH lifting equation,
Lifting Index, Maximum acceptable Weights and Forces, Distal upper extremities risk factors, Strain
Index, RULA, REBA.
6 Applied anthropometry - types, use, principles in application, design of work surfaces and seat design. 7
Visual displays for static information, visual displays of dynamic information, auditory, tactual and
DRAFT EC-156
olfactory displays and controls. Assessment of occupational exposure to noise, heat stress and dust
.Effect of vibration/ noise, temperature, illumination and dust on human health and performance
Total 42
S. Title, Author, Publisher and ISBN No.

No.
1. Barnes Ralph M., "Motion & Time study: Design and Measurement of Work", Wiley Text Books, ISBN-
10: 8126522178, 2009.
2 Marvin E, Mundel& David L, "Motion & Time Study: Improving Productivity", Pearson
Education,ISBN-10: 0136030440, 2000.
3 Benjamin E Niebel and FreivaldsAndris, "Methods Standards & Work Design", McGraw Hill,ISBN-
101259064840, 1997.
4 International Labour organization, "Work-study", Oxford and IBH publishing company Pvt. Ltd.,
N.Delhi, ISBN-10 8120406028, 2001
PE357 PRODUCT DESIGN & SIMULATION
1. Subject Code: PE-357 Course Title: Product Design & Simulation
5. Credits: 3
6. Semester: V
9. Objective: To allow students to develop the technical, analytical, and managerial skills necessary to
perform the tasks successfully.
DRAFT EC-157
Unit Content Contact Hours
No.
1 Stages in design process: 6
Introduction to various stages of the design process: Formulation of

problem, Generate alternatives, Evaluation, Guided Redesign. Case study.
2 Product life cycle: 6
New product introduction: early introduction, increased product life. Life

cycle management tool, System integration, QFD, House of quality,
Pugh’s method, Pahl and Beitz method. Case studies.
3 Value engineering:Introduction, nature and measurement of value. Value 6

analysis, job plan. Creativity and techniques of creativity. Value analysis
test. Case studies.
Material selection:Materials in design. The evolution of engineering

materials. Design tools and material data. Functional material, shape and
process. Material selection strategy, attribute limits, selection process,
common methods of material selection. Case studies.
4 Concurrent/ reverse engineering: 6
Introduction, basic principles, components, benefits of concurrent

engineering. Concept of reengineering.
Process selection: Introduction. Process classification: shaping, joining

and finishing. Systematic process selection, Ranking, process cost.
Computer – aided process selection.
5 Design for manufacture and assembly:Design for Manufacture and 8

Assembly (DFMA). Reasons for not implementing DFMA. Advantages
of DFMA with case studies. Design features and requirements with
regard to assembly, product Design for Manufacture in relation to any
two manufacturing processes: machining and injection molding. Need,
objectives.
6 System Simulation: Techniques of simulation, Monte Carlo method, 10
Experimental nature ofsimulation, Numerical computation techniques,
Continuous system models, Analog andHybrid simulation, Feedback
systems, Computers in simulation studies, Simulation softwarepackages.
DRAFT EC-158
Simulation of Mechanical Systems: Building of Simulation models,
Simulation oftranslational and rotational mechanical systems, Simulation
of hydraulic systems.
Total 42
1 Product Design and Development, “Karl T. Ulrich, Steven D. Eppinger”Mc

GrawHill.ISBN:9780072296471
2 Integrated Product and Process Development, “John M. Usher, Utpal Roy and H. R.
Parasaei.ISBN: 978-0-471-15597-3
3 Product Design for Manufacture and Assembly, “G. Boothroyd, P. Dewhurst and W.
Knight” MarceDaker.ISBN:978-1420089271
4. Engineering Design and Design for Manufacturing: A structured approach, “John R. Dixon
and CPoli” Field Stone Publishers, USA. ISBN: 9780964527201
5. Material Selection in Mechanical Design, “M. F. Ashby”Elsevier. ISBN: 9780080419077
PE359 TOTAL LIFE CYCLE MANAGEMENT
1. Subject Code: PE359 Course Title: Total Life Cycle Management
4. Relative Weight: CWS: 25 PRS: 0 MTE:25 ETE:50 PRE: 0
5. Credits: 3
6. Semester: V
9. Objective: To familiarize the students with the concept of Total Life Cycle, management of old vehicles,
applying life cycle thinking to define tradeoffs. This course also introduces to sustainability, use of
renewable resources.
DRAFT EC-159
S. No. Contents Contact Hours
1 Introduction : Definition of Total Life Cycle (TLC) – Conceptof TLC - 8

Life Cycle Impacts - Integrating Life Cycle Technologies- Products and
Processes Within TLC - TLC Methodology- TLC AccessementData to
Complex Products – ResultantImprovement for Product
2 Vehicles End of Life : Design for End of Old VehicleManagement - 8

Problems of Old Vehicles in EmergingMarkets - Recovery and Economic
Feasibility of MaterialsSuch As Plastic, Rubber, Aluminium, Steel, etc.
3 Trade-offs : Applying Life Cycle Thinking to Define TradeoffsAlong the 10

Supply, Manufacture - Use and End of Life Chain- Effects on the Customer
- Expectation of the Customer -Evaluate Product Cost on Fuel
Consumption, Emission,Durability, Environment and Health
4 Sustainability:What Is Sustainability - Use of RenewableResources - View 8

to Design Horizon.
5 Harmonization of Environmental Goals: TLC for Emerging Vs 8

Developed Markets - Rules and Regulations to Guide Designers -
International Common Practices for End of LifeVehicles.
Total 42
1 Life Cycle Management Case Study of an Instrument Panel /SAE, 1997/
2 Accident Reconstruction: Automobiles, Tractor-semitrailers, Motorcycles, and Pedestrians

/Society of Automotive Engineers, 1987 /0898834546, 9780898834543.
PE361 TOTAL QUALITY MANAGEMENT
DRAFT EC-160
1. Subject Code: PE-361 Course Title: Total Quality Management
5. Credits: 3
6. Semester: V
9. Objective: To understand the philosophy and core values of Total Quality Management (TQM);
determine the voice of the customer and the impact of quality on economic performance and long-term
business success of an organization;
Unit Content Contact

No. Hours
1 Introduction to Quality- Definition of Quality- product, user, value, and 9

manufacturing based perspectives, Dimensions of Quality, Quality Planning,
Quality costs- optimization of quality costs, seven tools of quality
control;Philosophies of Quality Gurus- Deming, Juran, Crosby, Feigenbaum,
Ishikawa, Taguchi. Comparison of Quality Philosophies.
2 Statistical Process Control-Introduction to Quality characteristics- variables 8

and attributes, Types and causes of variations, Control Charts for variables and
attributes, Process capability.
3 Acceptance Sampling-Sampling process and lots formation; Advantages and 7

applications of acceptance sampling; characteristics of O.C. Curve; Single,
double, multiple, sequential sampling; ASN, ATI, AOQL, AOQ, AQL, LQL,
Producer’s and Consumer’s risks.
4 Six Sigma and ISO 9000:2000- Principles of Six Sigma, Statistical basis, 6
Tools and techniques, DMAIC principle, application of six sigma in
manufacturing and service organizations, structure of ISO standards, Factors
leading to ISO, Implementation and registration, Benefits of ISO.
5 Life Testing-Reliability-Life testing: objective, failure data analysis, MTTF, 6

MTBF, hazard rate, exponential and Weibull models, system reliability-series,
parallel and mixed configurations, Markov model.
DRAFT EC-161
6 Reliability Design and Allocation- Design for reliability, reliability 6
improvement techniques, active redundancy and standby redundancy, K-out-of-
N redundancy and maintenance policies.
Total 42
1. Evans JR,Lindsay WM, “The Management and Control of Quality”, Cengage learning,
India, ISBN-10: 8131501361, 2011
2 BediKanishka,“Quality Management”,Oxford University Press India, ISBN-
10: 0195677951, 2006
3 Besterfield,“Total Quality Management”, Pearson Education, ISBN-10: 9332534454, 2015
4 Gryna FM, Chua RCH, Defeo JA, “Juran‟s Quality Planning and Analysis for Enterprise
Quality”, McGraw Hill Education (India) Private Limited, ISBN-10: 0070618488, 2006
PT361 HIGH PERFORMANCE POLYMERS
1. Subject Code: PT361 Course Title: High Performance Polymers

5. Credits: 03
6. Semester: ODD-V
9. Objective: To impart knowledge about heat resistant polymers, liquid
crystalline polymers, conducting and other special polymers.
S. Contents Contact
No. Hours
1 Heat resistant polymers: Requirements for heat resistance, Determination of heat 9
resistance, Synthesis, Structure-property relationships, Applications of heat
resistant polymers like polyamides, polyimides and its derivatives,
polyquinolines, polyquinoxalines, PBT, PBO, PBI, PPS, PPO, PEEK, engineering
plastic blends.
DRAFT EC-162
2 Liquid crystalline polymers, Concept of liquid crystalline phase, Theories of 9
liquid crystallinity, Characteristics of LC state and LCPs, Rheology of liquid
crystalline polymers, Blends of LCPs, Self reinforced composites, Applications.
3 Conducting polymers, Conduction mechanism, semi-conductors and conducting 9
polymers, Band theory, Doping of polymeric systems, Processing and testing of
conducting polymers, Applications and recent advances in conducting polymers.
4 Synthesis and applications of photosensitive polymers, Curing reactions. 6
5 Polymers in specialty applications: Polymers in agricultural applications, Green 9
houses, Mulches, Control release of agricultural chemicals, Seed coatings,
Polymers in construction and building applications.
11. Suggested Books

S. No. Name of Books/Authors/Publisher
1 Encyclopedia of Polymer science and Engineering Vol.1-17/ J.I. Kroschwitz, 2007
2 Additive for coatings/ John Bieleman/ Wiley-VCH, 2000.
3 Fire Properties of Polymeric Composites Materials/ A.P. Mouritz, A G. Gibson/ Springer,
2006.
4 Modern Biopolymers science: Bridging the divide between fundamentals treatise and
industrial application/S. Kasapis, I.T. Nortan, J.B. Ubbink/ Elsevier 2009
PT363 SEPARATION TECHNOLOGY
1. Subject Code: PT363 Course Title: Separation Technology

5. Credits: 03
6. Semester: ODD-V
9. Objective:

No. Hours
1 Separation factors and its dependence on process variables, classification and 7
characterization, thermodynamic analysis and energy utilization, kinetics and
mass transport, Theory of cascades and its applications.
2 Membrane Separations, Merits and demerits, Commercial, pilot plant 7
polarization of membrane processes and laboratory membrane permeators,
DRAFT EC-163
Dialysis, Reverse osmosis, Ultrafiltration, Membrane operations, Design
controlling factors.
3 Separation by Sorption Techniques, Types and choice of adsorbents, 7
chromatographic techniques, Retention theory mechanism, Design controlling
factors, ion exchange chromatography equipment and commercial processes,
recent advances in sorption technology.
4 Ionic Separations: Theory, mechanism and equipments for electrophoresis, 7
dielectrophoresis and electro dialysis, Controlling factors, Applications, Design
considerations.
5 Thermal Separation: Thermal diffusion, Rate law, Theories of thermal diffusion 7
for gas and liquid mixtures, Equipments design and applications, Zone melting,
Equilibrium diagrams, Controlling factors, Apparatus and applications.
6 Other Techniques: Adductive crystallization, Molecular addition compounds, 7
Clathrate compounds and adducts, Equipments, Applications, Economics and
commercial processes. Foam Separation: Surface adsorption, Nature of foams,
Apparatus, Applications and Controlling factors.
11. Suggested Books

1 New Chemical Engineering Separation Techniques/ Schoen/ Wiley Interscience, New York,
1972.
2 Separation Processes/ C.J. King/ Tata McGraw Hill, New Delhi,1982.
3 Bioseparations – Principles and Techniques/ B. Sivasankar/ Prentice Hall of India Pvt. Ltd,
New Delhi, 2005.
4 Separation process Principles/ Seader, Henley and Roper/ John Wiley & Sons 2010
5 Membrane Separation processes/ Kaushik Nath/ PHI , 2008.
PT365 NON-CONVENTIONAL ENERGY
1. Subject Code: PT365 Course Title: Non-Conventional Energy

5. Credits: 03
6. Semester: ODD-V
9. Objective: To make student aware about the fundamentals and applications
of non-conventional energy.
DRAFT EC-164
No. Hours
1 Renewable and non-renewable energy sources, trends in energy consumption, 6
Global and National scenarios, Prospects of renewable energy sources, Energy
Management.
2 Solar Energy: Solar radiation - beam and diffuse radiation, solar constant, earth 6
sun angles, measurement of solar radiation, flat plate collectors, concentrating
collectors, Solar air heaters-types, solar driers, Storage of solar energy-thermal
storage, Photo voltaics - solar cells & its applications.
3 Wind Energy: Basic system principles, Assessment of wind available, Design 4
principles, Manufactured designs, Sizing and storage of energy, System
efficiency, Overview of wind industry.
4 Energy from Biomass: Calorific value of Biomass samples, Pyrolysis, Biomass 6
conversion technologies, Biogas generation plants, classification, advantages and
disadvantages, constructional details, site selection, digester design
consideration, filling a digester for starting, maintaining biogas production, Fuel
properties of bio gas, utilization of biogas.
5 Geothermal Energy: Estimation and nature of geothermal energy, geothermal 4
sources and resources like hydrothermal, geo-pressured hot dry rock, magma.
Advantages, disadvantages, and application of geothermal energy.
6 Ocean Energy: Ocean Thermal Electric Conversion systems like open cycle, 4
closed cycle, Hybrid cycle. Energy from tides, basic principle of tidal power,
single basin and double basin tidal power plants, advantages, limitation and scope
of tidal energy. Wave energy and power from wave, wave energy conversion
devices, advantages and disadvantages of wave energy.
7 Magnetohydrdynamic Power Generation: Principle of MHD power generation, 4
MHD system, Design problems and developments, gas conductivity, materials
for MHD generators and future prospects.
8 Fuel Cells: Design principle and operation of fuel cell, Types of fuel cells, 4
conversion efficiency of fuel cell, applications of fuel cells.
9 Hydrogen Energy: Hydrogen Production methods, Hydrogen storage, hydrogen 4
transportation, utilization of hydrogen gas, hydrogen as alternative fuel for
vehicles.
11. Suggested Books

1 Principles of Sustainable Energy Systems, Second Edition/ Frank Kreith, Susan Krumdieck/
CRC Press, 2013.
2 Non-conventional energy sources/ G.D. Rai/ Khanna Publishers, 2004.
3 Solar Energy: Fundamentals and Applications/ H.P. Garg & Jai Prakash/ Tata McGraw Hill,
2000
4 Solar Engineering of Thermal Processes/ Duffic and Beckman/ John Wiley, 2013
DRAFT EC-165
5 Non Conventional Energy Resources/ Saeed and Sharma/ S.K. Kataria& Sons ,2013
PT367 POLYMER WASTE MANAGEMENT
1. Subject Code: PT367 Course Title: Polymer Waste Management
5. Credits: 03
6. Semester: ODD-V
9. Objective: To impart knowledge about polymer waste and their management.

No. Hours
1 Polymer and Plastics Waste: Definition of plastics waste and the associated 8
problems, Identification, collection methods and separation. Integrated waste
management – source reduction, recycling, energy recovering process through
thermal and biological destruction, Land filling and composting.
2 Plastics waste management: Source reduction, reuse, repair, recycling, and 8
incineration with examples. Plastics recycling: Classification, Code of practice,
Primary, secondary, territory and quaternary recycling with examples, Waste
plastics as fillers.
3 Recycling and degradation of plastics: Recycling and sustainability correlation, 9
Basic principles and recovery, recycling and resource conservation.
4 Recycling of plastics by surface refurbishing, Application of a coating, polishing, 9
Plastics, Environmental and Thermal ageing, Chemical degradation, Wear and
erosion, Biodegradable plastics – an overview.
5 Environmental issues, policies and legislation in India. 8
11. Suggested Books

1 Plastics Recycling – Products and Processes/ Ehrig (Ed.)/ Hanser Publication, 1993
2 Recycling and recovery of plastics/ Brandrup/ Hanser Publishers, New York, 1996
3 Handbook of Plastics Recycling/ By Francesco La Mantia/ Rapra Tech Ltd , 2002
4 Introduction to Plastics Recycling/ By VannessaGoodship/ Rapra Tech Ltd ,2007
DRAFT EC-166
PT369 NANOTECHNOLOGY IN POLYMERS
1. Subject Code: PT369 Course Title: Nanotechnology in Polymers

5. Credits: 03
6. Semester: ODD-V
9. Objective: To make student aware about the applications of nanopolymers in
various fields.
S. Contents Contact
No. Hours
1 Concepts of nanotechnology, Time and length scale in structures, Nanosystems, 8
Dimensionality and size dependent phenomena, Surface to volume ratio-Fraction of
surface atoms, Surface energy and surface stress, surface defects, Properties at
nanoscale (optical, mechanical, electronic, and magnetic).
2 Nano-materials, Classification based on dimensionality, Quantum Dots, Wells and 8
Wires, Carbon-based nano-materials, Metal based nano-materials, Nanocomposites,
Nanopolymers, Nanoglasses, Nanoceramics, Biological nanomaterials.
3 Synthesis of nanopolymers, Chemical Methods, Metal Nanocrystals by Reduction, 9
Solvothermal Synthesis, Photochemical Synthesis, Sonochemical Routes, Chemical
Vapor Deposition, Metal Oxide - Chemical Vapor Deposition, Physical Methods
such as ball Milling, electrodeposition, spray pyrolysis, flame pyrolysis, DC/RF
magnetron sputtering, Molecular beam epitaxy.
4 Nanofabrication, Photolithography and its limitations, Electron beam lithography, 9
Nanoimprint, Soft lithography patterning, Characterization with Field Emission
Scanning Electron Microscopy, Environmental Scanning Electron Microscopy, High
Resolution Transmission Electron Microscope, Scanning Tunneling Microscope,
Surface enhanced Raman spectroscopy, X-ray Photoelectron Spectroscopy, Auger
electron spectroscopy, Rutherford back scattering spectroscopy.
5 Applications of nanomaterials, Solar energy conversion and catalysis, Molecular 8
electronics and printed electronics, Nanoelectronics, Polymers with aspecial
architecture, Applications in displays and other devices, Nanomaterials for data
storage, Photonics, Plasmonics, Nanomedicine, Nanobiotechnology and
Nanotoxicology.
11.Suggested Books
1 Organic and Inorganic Nanostructures/ Nabok/ Artech House, 2005.
2 Nanoscience: Nanotechnologies and Nanophysics/ Dupas, Houdy, Lahmani/ Springer-Verlag
Berlin Heidelberg ,2007
DRAFT EC-167
3 Nanostructured Materials and Nanotechnology/ H.S. Nalwa/ Academic Press , 2002
4 A Textbook of Nanoscience and Nanotechnology/ Pradeep/ Tata McGraw Hill Education Pvt.
Ltd. , 2012
PT371 APPLICATIONS OF POLYMER BLENDS AND

COMPOSITE
1. Subject Code: PT371 Course Title: Applications of Polymer Blends and Composite
5. Credits: 03
6. Semester: ODD-V
9. Objective: To make student aware about the applications of polymers, blends
and composites.

No. Hours
1 Concepts of polymer blends, Advantages of blends over conventional polymers, 8
Significance of polymer blend technology, Different steps involved in designing
of a blend, Different methods of blending, Characterization of polymer blends.
2 Compatibilization and Phase Morphology, Role of compatibilizers in blend 8
technology, techniques of compatibilization, Phase structure development in
polymer blends, Factors affecting morphology of polymer blends, Properties of
polymer blends.
3 Reinforcements, Properties and applications of Glass, Carbon, Kevlar, 9
polyethylene, boron, ceramic and natural fibers. Concepts of matrix material,
Thermoset matrix materials like - epoxy, polyester, vinyl esters, phenolic resin,
polyimides, Thermoplastic matrix materials like - polyolefins, polyether ether
ketones, polyphenylene sulfide, thermoplastic polyimides.
4 Concept of composites, particulate and fibrous composites, Properties of 9
composites, Fabrication of continuous and short fiber composites and particulate
composites, mechanical and physical properties
5 Applications of blends and composites for civil, aerospace, automobiles etc 8
11. Suggested Books

1 Fibre Reinforced composites/ P. K. Malik/ Marcel Deckar, 1988.
DRAFT EC-168
2 Composites Manufacturing: Materials, Product, and Process Engineering/ S.K. Mujumdar/
CRC press ,2002
3 Fibre-glass Reinforced Plastics/ N. P. Cheremisinoff (Ed)/ Noyce Pub, 1988.
4 Design Data for Reinforced Plastics/ N. L. Hancex, R. M. Mayer/ Chapman Hall, 1994.
5 Reinforced Plastics: Properties and Applications/ Raymond Seymour/ The Materials
Information Society, 1991.
IT351 Artificial Intelligence and Machine

Learning
NAME OF DEPTT: Information Technology
1. Subject Code: IT351 Course Title: Artificial Intelligence and Machine Learning
5. Credits: 3
6. Semester: ODD
8. Pre-requisite: Discrete Mathematics
9. Objective: The student should be able to understand the different supervised, unsupervised and
reinforcement learning algorithms and choose the appropriate machine learning tool for different real world
examples.
S.No. Contents Contact Hours
1. Introduction to Artificial Intelligence and Machine learning, State Space 6

representation of problems, Concept of Search, overview of different tasks:
classification, regression, clustering, control, Concept learning.
2. Heuristic Search Techniques: Generate and Test, Hill Climbing, Best-first search, 6
Branch and bound, A* algorithm, Game playing.
DRAFT EC-169
3. Knowledge Representation:Propositional logic, Predicate Logic, semantic nets, 8
frames
4. Supervised Learning: Decision trees, nearest neighbors, linear classifiers and 8

kernels, neural networks, linear regression; Support Vector Machines.
5. Unsupervised Learning: Clustering, Expectation Maximization, Dimensionality 8

Reduction, Feature Selection, PCA, factor analysis, manifold learning.
6. Applications &Research Topics: Applications in the fields of web and data mining, 6
text recognition, speech recognition
TOTAL 42
11. Suggested Books

Reprint
Text Book
1. Artificial Intelligence by Elaine Rich, K. Knight, McGrawHill 2009
1. Introduction to Machine Learning, Alpaydin, E., MIT Press, 2004
2. Machine Learning, Tom Mitchell, McGraw Hill, 1997. 1997
3. Elements of Machine Learning, Pat Langley Morgan Kaufmann 1995

Publishers, Inc. 1995. ISBN 1-55860-301-8
Reference Book
4. The elements of statistical learning, Friedman, Jerome, Trevor Hastie, and 2001
Robert Tibshirani. Vol. 1. Springer, Berlin: Springer series in statistics,
2001.
5. Machine Learning: A probabilistic approach, by David Barber. 2006
DRAFT EC-170
6 Pattern recognition and machine learning by Christopher Bishop, 2006
Springer Verlag, 2006
IT353 Data Structures and Algorithms
1. Subject Code: IT353 Course Title: Data Structures and Algorithms
5. Credits: 3
6. Semester: ODD
9. Objective: The objective of the course is to familiarize students with basic data structures and their use
in fundamental algorithms.

1. Introduction: Introduction to Algorithmic, Complexity- Time-Space Trade off. 8
Introduction to C programming through Arrays,
Stacks, Queues and Linked lists.
2. Trees: Basic Terminology, Traversals, Binary search trees, optimal and average 7
BST’s. 2-4 trees, Applications of Binary search Trees, Complete Binary trees,
Extended binary trees.
3. Introduction to algorithms: Concept of algorithmic efficiency, run time analysis 9
of algorithms, Asymptotic Notations. Growth of Functions, Master's Theorem,
Searching and Searching: Linear Search, Binary search, Insertion Sort, Quick
sort, Merge sort, Heap sort, Radix Sort.
4. Graphs: Terminology and Representations, Graphs & Multi-graphs, Directed 8
Graphs, Representation of graphs, Breadth first search and connected components.
Depth first search in directed and undirected graphs and strongly connected
components.
5. Spanning trees: Prim's and Kruskal’s algorithm, union-find data structure. 10
Dijkstra’s algorithm for shortest paths, shortest path tree. Directed acyclic graphs:
topological sort and longest path.
DRAFT EC-171
Dynamic programming: Principles of dynamic programming. Applications:
Matrix multiplication, Travelling salesman Problem.
42
11. Suggested Books

Publication/
Reprint
Text Books:
1. Horowitz and Sahni, “Fundamentals of Data structures”, Galgotia 1983
publications
2. Tannenbaum, “Data Structures”, PHI 2007( Fifth
Impression)
3. T .H . Cormen, C . E . Leiserson, R .L . Rivest “Introduction to Algorithms”, 2011 ( reprint)
3rd Ed., PHI.
4. E. Horowitz, S. Sahni, and S. Rajsekaran, “Fundamentals of Computer

Algorithms,” Galgotia Publication
Reference Books
1. R.L. Kruse, B.P. Leary, C.L. Tondo, “Data structure and program design in 2009( Fourth
C”, PHI Impression)
2. Aho ,Ullman “Principles of Algorithms ”
IT355 Communication and Computing

Technology
1. Subject Code: IT355 Course Title: Communication and Computing Technology
DRAFT EC-172
5. Credits: 3
6. Semester: ODD
8. Pre-requisite: Operating systems, Algorithm Design and Analysis and data structures
9. Objective: To introduce the concept of Communications in Computer networks

1. Introduction to Goals and Applications of Networks, Network structure and 6

architecture, The TCP/IP reference model, services, Network Topology.
2. Data Link Layer and Medium Access sub layer - Channel Allocations, LAN 6
protocols -ALOHA protocols - Overview of IEEE standards - FDDI. - Elementary
Data Link Protocols, Sliding Window protocols.
3. Network Layer: Routing, Congestion control, Internetworking -TCP / IP, IP packet, 8

IP address, IPv6 and Mobile IP.
4. Transport Layer: Design issues, TCP and UDP, connection management, 8

Congestion control, Leaky bucket, Token bucket algorithm. QoS.
5. Application Layer: File Transfer, Access and Management, Electronic mail, 6

Virtual Terminals, Internet and Public Networks, Firewalls
6. Information and Web security: IP Security, Architecture, Authentication header, 8

Encapsulating security payloads, combining security associations, Secure Socket
Layer(SSL) and transport layer security, TSP, Secure Electronic Transaction (SET),
Electronic money.
TOTAL 42
11. Suggested Books

Reprint
Text Book
1. S. Tananbaum, “Computer Networks”, 3rd Ed, PHI 1999

2.  U. Black, “Computer Networks-Protocols, Standards and Interfaces”, PHI 1996
3. W. Stallings, “Computer Communication Networks”, PHI 1999
DRAFT EC-173
3. Data Communications and Networking, Behrouz A. Forouzan 5/e 2013
Reference Book
4. William Stallings, “Cryptography and Network Security: Principals and 2001

Practice”, Prentice Hall, New Jersy.
5. Behrouz A. Forouzan, “Cryptography and Network Security”, TMH. 2006
IT357 Internet and Web Programming
1. Subject Code: IT357 Course Title: Internet and Web Programming
5. Credits: 3
6. Semester: ODD
9. Objective: To introduce the concept of internet and web programming

1. Internet and WWW: Internet basic, Introduction to internet and its applications, E- 6
mail, telnet, FTP, e-commerce, video conferencing, e-business. Internet service
providers, domain name server, internet address World Wide Web (WWW): World
Wide Web and its evolution, uniform resource locator (URL), browsers - internet
explorer, netscape navigator, opera, firefox, chrome, mozilla. Search engine, web
saver - apache, IIS, proxy server, HTTP protocol.
2. WEBSITES BASIC ANDWEB 2.0: Web 2.0: Basics-RIA Rich 6
Internet Applications - Collaborations tools - Understanding websites and web
servers: Understanding Internet – Difference between websites and web server-
Internet technologies Overview – Understanding the difference between internet and
intranet; HTML and CSS: HTML 5.0 , XHTML, CSS 3.
DRAFT EC-174
3. E-MAIL SECURITY & FIREWALLS : PGP - S/MIME - Internet Firewalls for 8
Trusted System: Roles of Firewalls - Firewall related terminology- Types of
Firewalls - Firewall designs - SET for E-Commerce Transactions, intellectual
property: copyright, patents, trademarks, cyber laws
4. SERVELETS AND JSP: JSP Technology Introduction-JSP and Servelets- Running 8
JSP Applications Basic JSP- JavaBeans Classes and JSP-Tag Libraries and Files-
Support for the Model- View- Controller Paradigm- Case Study- Related
Technologies.
5. XML: Introduction to XML, uses of XML, simple XML, XML key components, 6
DTD and Schemas, Well formed, using XML with application.XML, XSL and
XSLT. Introduction to XSL, XML transformed simple example, XSL elements,
transforming with XSLT
6. PHP: Starting to script on server side, Arrays, function and forms, advance 8
PHP, Basic command with PHP examples, Connection to server, creating database,
selecting a database, listing database, listing table names creating a table, inserting
data, altering tables, queries, deleting database, deleting data and tables, PHP my
admin and database bugs.
TOTAL 42
11. Suggested Books

Reprint
Text Books
1. Internet and Web Technologies by Raj Kamal, Tata McGraw Hill 2002
edition. (ISBN: 9780070472969)
2. An Introduction to Search Engines and Web Navigation, Mark Levene, 2010
Pearson Education. (ISBN: 978047052684)
3. Modeling the Internet and the Web,PierreBaldi,PaoloFrasconi, Padhraic 2003
Smyth, John Wiley and Sons Ltd. (ISBN: 978-0-470-84906-4)
Reference Books
4. HTML: A Beginner’s Guide by Wendy Willard, Tata McGraw-Hill 2009
(ISBN: 9780070677234)
5. PHP and MySQL for Dynamic Web Sites, Ullman, Larry, Peachpit 2012
Press.1 (ISBN: 978-0-321-78407-0)
IT359 Java Programming
1. Subject Code: IT359 Course Title: Java Programming
DRAFT EC-175
5. Credits: 3
6. Semester: ODD
9. Objective: To introduce the concept of java programming

1. Introduction to Java: Programming language Types and Paradigms, Computer 6

Programming Hierarchy, How Computer Architecture Affects a Language? , Why
Java?, Flavors of Java, Java Designing Goal, Role of Java Programmer in Industry,
Features of Java Language, JVM –The heart of Java , Java’s Magic Byte code.
2. The Java Environment: Installing Java, Java Program Development, Java Source 6
File Structure, Compilation, Executions. Lexical Tokens, Identifiers, Keywords,
Literals, Comments, Primitive Datatypes, Operators Assignments.
3. Object Oriented Programming: Class Fundamentals , Object & Object reference, 8
Object Life time & Garbage Collection, Creating and Operating Objects ,
Constructor & initialization code block, Access Control, Modifiers, methods Nested
, Inner Class &Anonymous Classes, Abstract Class & Interfaces Defining Methods,
Argument Passing Mechanism, Method Overloading, Recursion, Dealing with Static
Members, Finalize() Method, Native Method.
4. Extending Classes and Inheritance: Use and Benefits of Inheritance in OOP, 8
Types of Inheritance in Java, Inheriting Data members and Methods, Role of
Constructors in inheritance, Overriding Super Class Methods, Use of “super”,
Polymorphism in inheritance, Type Compatibility and Conversion Implementing
interfaces.
5. Package: Organizing Classes and Interfaces in Packages, Package as Access 6
Protection, Defining Package, CLASSPATH Setting for Packages, Making JAR
Files for Library Packages Import and Static Import Naming Convention For
Packages.
6. GUI Programming: Designing Graphical User Interfaces in Java, Components and 8
Containers, Basics of Components, Using Containers, Layout Managers, AWT
Components, Adding a Menu to Window, Extending GUI Features Using Swing
Components, Java Utilities (java.util Package) The Collection Framework:
Collections of Objects, Collection Types, Sets , Sequence, Map, Understanding
Hashing, Use of Array List & Vector.
TOTAL 42
DRAFT EC-176
11. Suggested Books

Reprint
Text Books
1. The Complete Reference Java,, Herbert Schildt, 7th Edition
ISBN: 978-0-07163177-8, Publisher: McGraw Hill
2. Thinking in Java, Bruce Eckel, ISBN: 0-13-187248-6, Publisher: 4th Edition

Prentice Hall
3. The Java Programming Languages,, Ken Arnold, ISBN-13: 978- 4th Edition
032134980, Publisher: Sun
4. Java in Nutshell,, Benjamin, ISBN: 9781449371296, Publisher: 6th Edition

O'Reilly Media, Inc.
DRAFT EC-177

Ece PDF

Uploaded by

Copyright:

Available Formats

Ece PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ece PDF

Uploaded by

Copyright:

Available Formats

DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING

DELHI TECHNOLOGICAL UNIVERSITY

(Formerly Delhi College of Engineering)

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

III Year: Odd Semester

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

IV Year: Odd Semester

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

S. Code Title Area Cr L T P TH PH CWS PRS MTE ETE PRE

List of Departmental Elective Courses

54. IT 355 Communication and Computing Technology

1. Subject Code: EE 251 Course Title: Electronic Instrumentation and Measurements

11. Suggested Books

S.No. Name of Books / Authors/ Publishers Year of

1. Subject Code: EC 201 Course Title: Analog Electronics – I

10. Details of Course

11. Suggested Books

2. Fundamentals of Microelectronics circuits by B. Razavi. 2012

1. Subject Code: EC 203 Course Title: Digital Design – I

11. Suggested Books

1. Subject Code: EC – 205 Course Title: Signals and Systems

4. Z-Transform: Basic principles of z-transform, z-transform definition, Relationship 8

11. Suggested Books

11. Suggested Books

1. Subject Code: HU201 Course Title: Engineering Economics

11. Suggested books

1. Subject Code: EE – 262 Course Title: Electromagnetics

1. Subject Code: EC 202 Course Title: Analog Electronics – II

S.No. Contents Contact

1. Subject Code: EC 204 Course Title: Digital Design – II

S.No. Contents Contact

11. Suggested Books

4. Fundamental of Logic Design by Roth ; Cengage learning. 2013

5. Advanced Digital design with Verilog HDL by Michael D Ciletti 2010

8. Introduction To Digital Systems by M.Ercegovac, T. Lang and J.H.Morcno; 2006

1. Subject Code: EC –206 Course Title: Communication Systems

11. Suggested Books

1. Subject Code: EC 208 Course Title: Computer Architecture

2. Computer Systems Organization and Architecture by Carpinelli; Pearson 2001

5. Computer Organization & Architecture, by Stallings, W; PHI. 2012

7. Computer Architecture: A Quantitative Approach by D. Patterson and J. 2002

1. Subject Code : MG201 Course Title : Fundamentals of Management

1. Subject Code: EC301 Course Title: Digital Communication

S. No. Contents Contact

11. Suggested Books:

S. Name of Authors /Books / Publishers Year of

1. Subject Code: EC 303 Course Title: Linear Integrated Circuits

11. Suggested Books

S.No. Name of Books / Authors/ Publishers Year of

2. Rolf Schaumann and Mac E.VanValkenburg by Oxford Indian Edition 2005

S.No. Name of Books, Authors, Publishers Contact

11. Suggested Books

S.No. Name of Books, Authors, Publishers Year of

1. Subject Code: EC 302 Course Title: VLSI Design

S.No. Contents Contact

11. Suggested Books

1. Subject Code: EC 304 Course Title: Digital Signal Processing