SURFACE VEHICLE J20 ™ -2 MAR201 8

STANDARD Issued 2001 -1 1

Stabilized 201 8-03
Superseding J20-2 JUN2009

Coolant Hose - Normal Service Type Convoluted, Wire Support Hose

(Supplement to SAE J20 for Government Use Replacing Part of MS51 008)

RATIONALE

This document has been determined to contain basic and stable technology which is not dynamic in nature.

STABILIZED NOTICE

This document has been declared "Stabilized" by the SAE Non-Hydraulic Hose Committee and will no longer be subjected
to periodic reviews for currency. Users are responsible for verifying references and continued suitability of technical
requirements. Newer technology may exist.

__________________________________________________________________________________________________________________________________________
SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely
voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and
suggestions.
Copyright © 201 8 SAE International
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) SAE values your input. To provide feedback
Tel: +1 724-776-4970 (outside USA) on this Technical Report, please visit
Fax: 724-776-0790 http://standards.sae.org/J20/2_201 803
Email: CustomerService@sae.org
SAE WEB ADDRESS: http://www.sae.org
SAE INTERNATIONAL J20™ -2 MAR201 8 2 OF 4
_________________________________________________________________________________________________

1. Scope—This SAE Standard provides ordering information for any SAE 20R5 hose type (such as “EC, HT, LT”
or combination thereof.) This is a wire-reinforced hose for coolant circulating systems of automotive type
engines. This hose consists of a convoluted section with plain ends. The hose shall contain a wire helix or
helices in the convoluted section. It is a supplement for Government use but may be used by others.

2. References

2.1 Applicable Publications—The following publications form a part of this specification to the extent specified
herein. Unless otherwise indicated, the latest version of SAE publications shall apply.

2.1 .1 SAE P UBLICATION —Available from SAE, 400 Commonwealth Drive, Warrendale, PA 1 5096-0001 .

SAE J20—Coolant System Hoses

2.1 .2 ISO P UBLICATIONS —Available from ANSI, 1 1 West 42nd Street, New York, NY 1 0036-8002.

ISO 9001 —Quality systems—Model for quality assurance in design, development, production, installation
and servicing

2.1 .3 G OVERNMENT P UBLICATIONS —Available from U. S. Government, DOD SSP, Subscription Service Division,
Building 4D, 700 Robbins Avenue, Philadelphia, PA 1 91 1 1 -5094.

Federal Specification ZZ-H-428—Hose; Non-Metallic and Hose; Preformed: (for Coolant Systems of
Automotive and Other Liquid-Cooled Engines)
Military Drawing MS51 008—Hose, Preformed: Flexible, Engine Coolant, 1 -1 /4, 1 -1 /2, 1 -3/4, 2, 2-1 /4, 2-1 /
2, 3 ID

2.1 .4 AUTOMOTIVE I NDUSTRY P UBLICATION —Available from AIAG, 26200 Lasher Road, Suite 200, Southfield, MI
48034-71 00.

QS 9000—Quality System Requirements

SAE INTERNATIONAL J20™ -2 MAR201 8 3 OF 4
_________________________________________________________________________________________________

3. Technical Requirements— The following requirements are in addition to the requirements of SAE J20.

3.1 Certification—Manufacturers/suppliers of hose to the Government must be ISO 9001 or QS-9000 certified
and provide their certification to provide this SAE J20/2 hose.

3.2 Lengths—The lengths specified in Table 1 shall comply with SAE J20 Table 2 tolerances.

TABLE 1 —NOMINAL LENGTHS

Nominal Length Actual Length
mm mm (in)
1 27 1 27.0 (5.00)
1 52 1 52.4 (6.00)
1 78 1 77.8 (7.00)
203 203.2 (8.00)
229 228.6 (9.00)
254 254.0 (1 0.00)
280 279.4 (1 1 .00)
305 304.8 (1 2.00)
356 355.6 (1 4.00)
406 406.4 (1 6.00)
457 457.2 (1 8.00)
508 508.0 (20.00)
550 550.0 (22.00)
61 0 609.6 (24.00)
660 660.4 (26.00)
71 1 71 1 .2 (28.00)
762 762.0 (30.00)
81 3 81 2.8 (32.00)
864 863.6 (34.00)
91 4 91 4.4 (36.00)
965 965.2 (38.00)

3.3 Inside Diameters—The inside diameters specified in Table 2 shall comply with SAE J20 tolerances.

TABLE 2—NOMINAL INSIDE DIAMETERS (ID)

Nominal ID Actual ID
mm mm (in)
25 25.40 (1 .00)
32 31 .75 (1 .25)
38 37.50 (1 .50)
44 44.45 (1 .75)
51 50.80 (2.00)
57 57.1 5 (2.25)
64 63.50 (2.50)
76 76.20 (3.00)

3.4 Wall Gauge Range—Wall gauge range shall comply with SAE J20.

3.5 Marking—For U.S. Government use only, marking shall consist of the following on one or both cuffs:

a. Part Identification Number (see 4.2)

b. Manufacturer’s identification code (CAGE) or trademark symbol
c. Month and year of manufacture
SAE INTERNATIONAL J20™ -2 MAR201 8 4 OF 4
_________________________________________________________________________________________________

3.5.1 If there is insufficient space on the hose for the required marking due to small ID hose or too short a straight
length, a label carrying the required information taped around the individual pieces of hose in lieu of the
previous method of marking.

3.5.2 Marking for non-Government users shall be agreed upon by the customer and manufacturer.

4. Notes

4.1 Intended Use—The flexible, wire-reinforced coolant hose is intended for use in automotive cooling systems. It
is commonly known as universal type hose.

4.2 Part Identification Number—Part numbers shall be constructed as indicated in Figure 1 .

FIGURE 1 —PART IDENTIFICATION NUMBER

4.3 Government Specification Replacement—This document is a replacement for portions of Federal

Specification ZZ-H-428, “Hose; Non-Metallic and Hose; Preformed: (for Coolant Systems of Automotive and
Other Liquid-Cooled Engines.)” This document is also a replacement for part of Military Drawing MS51 008,
“Hose, Preformed: Flexible, Engine Coolant, 1 -1 /4, 1 -1 /2, 1 -3/4, 2, 2-1 /4, 2-1 /2, 3 ID.”

4.4 Cross Reference Information—Table 3 shows the relationship between designations in ZZ-H-428 and this
document. MS51 008 only provided part numbers for ZZ-H-428, Type V, Grade A, Class 2 hose. Those part
numbers are now replaced by SAE J20/2ECLT Class A part numbers.
TABLE 3—CROSS REFERENCE DESIGNATION
J20 J20 ZZ-H-428 ZZ-H-428 ZZ-H-428
Designation Class Type Grade Class
SAE-J20/2ECLT A V A 2
SAE-J20/2ECLT A V A 3
SAE-J20/2EC B V B 1
SAE-J20/2EC C V B 2
SAE-J20/2EC D-1 V B 3
SAE-J20/2EC D-3 V B 4

4.5 Other Sizes—Sizes and tolerances other than those listed in this document shall be agreed upon by the
supplier and purchaser. The requirements of SAE J20 shall be the met.

4.6 Key Words—Automotive, flexible hose, universal hose.

PREPARED BY THE SAE COOLANT HOSE COMMITTEE