Mech - 2010 PDF
Mech - 2010 PDF
( MECH - 01 )
QUESTION PAPER
Instructions: Please read the following instructions carefully before writing your answers:
1) All Questions in Part - A & Part - B are compulsory.
2) Each Questions in Part - A carries 1 mark and that in Part - B carries 5 marks.
3) There are four options - (A), (B), (C), (D) given against each question in Part - A out of which
only one is the most appropriate answer.
If (A) is correct, round on the correct option like (A)
4) The discarded answer if any, must be crossed properly and supported by initial of the
candidate.
5) Use only blue or black ball pen only. Use of Pencil is not allowed.
6) No sheet from the Question Paper / Answer Book should be detached.
7) You may do rough work, if required, on the blank sheets.
8) Please DO NOT repeat DO NOT write your name anywhere on the Question Paper /
Answer sheet. If name is found marked on the Question paper / Answer sheet, this will
render the candidate disqualified.
Part - B
Q.81 Q.82 Q.83 Q.84 Total
(5) (5) (5) (5) (20)
3 3
Q.03. 64 + 0.125 + 5.5 is:
(A) 8 (B) 6 (C) 10 (D) 12
7 10 5
Q.04. The value of ? ? is:
6 3 2
(A) 7 (B) 8 (C) 2 (D) 5
Q.05. One solder is made of 45% of tin and 55% of lead. What will be the quantity of tin and
lead in 28 kg of solder ?
(A) 15.4 & 12.6 kg (B) 12.6 & 15.4 kg (C) 12 & 16 kg (D) 16 & 12 kg
Q.06. 20 workers can complete a job in 60 Hrs. 25 workers will do the job in:
(A) 40 Hrs (B) 48 Hrs (C) 60 Hrs (D) 75 Hrs
Q.07. Amount of heat required to raise the temperature of one gm substance through 10C is
called:
(A) Latent heat of fusion (B) Latent heat of vaporisation
(C) Specific heat (D) Thermal capacity
tan 650
Q.08. Evaluation of is:
cot 250
(A) 1 (B) 2 (C) 3 (D) 4
1 ? tan 2 A
Q.09. What is the value of ?
1 ? cot 2 A
(A) sec2A (B) -1 (C) tan2A (D) cot2A
Q.10. Find area of sector of a circle with radius 7 cm and of angle 300. (? =22/7):
(A) 13 cm2 (B) 15 cm2 (C) 17 cm2 (D) 19 cm2
Q.11. The single equivalent discount of two successive discounts 20% and 10% is:
(A) 30 % (B) 32 % (C) 35 % (D) 28 %
Q.12. In two hours the minute hand of a clock rotates through an angle of:
(A) 600 (B) 900 (C) 1800 (D) 7200
Q.13. The perimeter of a square is 504 cms. What is the area of the square ?
(A) 2016 sq.cms. (B) 15876 sq.cms. (C) 15376 sq.cms. (D) 1008 sq.cms.
UNCONTROLLED
( MECH - 03 )
Q.14. Toughness of a material means:
(A) Strength (B) Fatigue resistance
(C) Stress relieving (D) Machinability
Q.16. Average of five consecutive odd numbers is 95. What is the fourth number in
descending order ?
(A) 91 (B) 93 (C) 99 (D) 97
Q.18. The temperature at which the readings of Fahrenheit and Centigrade thermometer are
the same is:
(A) zero (B) 250C (C) ? 400C (D) 320C
Q.19. The main element for corrosion resistance in stainless steel is:
(A) Chromium (B) Magnesium (C) Cobalt (D) Vanadium
Q.20. What least number should be subtracted from 9889 to make it a perfect square ?
(A) 84 (B) 88 (C) 108 (D) 74
Q.22. In gas welding, lead of blow pipe is held at what angle to the plane of weld:
(A) 300 to 400 (B) 600 to 700 (C) 150 to 250 (D) None of these
Q.36. In matching the thickness of the chip produced as compare to the depth of cut is:
(A) Less
(B) More
(C) Same
(D) May be less or more depending upon the material of the tool
Q.40. The surface finish of parts produced by hot working process as compared to cold
working process is:
(A) Poor (B) Better (C) Same (D) None of these
Q.46. During the transformation of water into steam, the temperature remains constant, the
heat added is known as:
(A) Liquid heat (B) Total heat
(C) Latent heat of steam (D) Specific heat
Q.50. In spot welding, the spacing between two spot weld should not be less than:
(A) d (B) 1.5 d (C) 3d (D) 6d
where d is Electrode tip diameter
Q.51. The electrode tip diameter (d) in spot welding should be equal to:
(A) t (B) 1.5 t (C) 3 t (D) 6 t
where t is thickness of plate
Q.57. In a planer:
(A) Tool and work both reciprocate
(B) Tool is stationary and the work reciprocates
(C) Work is stationary and the tool reciprocates
(D) None of these
Q.63. In arc welding, the electric arc is produced between the work and the electrode by:
(A) Flow of current (B) Contact resistance
(C) Voltage (D) All of these
Q.70. The helix angle for a milling cutter is in the range of:
(A) 25 degree to 45 degree (B) 35 degree to 60 degree
(C) 10 degree to 15 degree (D) 5 degree to 10 degree
Q.80. The raw material used for manufacturing aluminium oxide as abrasive material is:
(A) Silica sand (B) Bauxite (C) Quartz (D) Silicon carbide
PART - B
(Each question carries 5 marks)
Q.81. If 3 men and 5 women do a piece of work in 8 days and 2 men and 7 children do the
same in 12 days. How many women can do as much work in 1 day as 21 children ?
Q.84. On grinding wheel label marking is A46K5V17, Explain meaning of symbols used in
marking.